Canon imageRUNNER Advance C5550i

Общие характеристики
Размещение	настольный
Цветность печати	цветная
Печать фотографий
Телефон
Тип устройства	МФУ
Макс. формат	A3
Копир
Факс
Сканер
Технология печати	лазерная
Тип	лазерный/светодиодный
Макс, длина отпечатка	420
Макс, ширина отпечатка	297
Количество цветов	4
Пигментные чернила
Двусторонняя печать
Печать без полей
Макс, разрешение для ч/б печати
По Y	1 200
По X	1 200
Скорость ч/б печати
A4	50
A3	27
Время выхода первого отпечатка
Ч/б	4,1
Цветн,	6,1
Шаг масштабирования	0,01
Макс, количество копий за цикл	999
Значение масштаба
Минимальное	0,25
Максимальное	4
Макс, разрешение (ч/б)
По Y	600
По X	600
По X	400
Устройство автоподачи оригиналов	одностороннее
Слайд-адаптер
Макс. формат оригинала	A3
Оттенки серого	256
Емкость устройства автоподачи оригиналов	150
Тип сканера	планшетный/протяжный
Стандарт TWAIN
Отправка изображения по e-mail
Макс, размер сканирования
По Y	420
По X	297
Разрешение сканера
По Y	400
По Y (улучшенное)	600
По Х	600
По Х (улучшенное)	600
Скорость сканирования
Ч/б	80
Цветн,	80
Количество картриджей	4
Ресурс ч/б картриджа/тонера	69 000
Ресурс цветного картриджа/тонера	60 000
Печать на:
CD/DVD
Фотобумаге
Рулоне
Этикетках
Конвертах
Карточках
Пленках
Глянцевой бумаге
Матовой бумаге
Плотность бумаги
Минимальная	51
Максимальная	300
PC Fax
Макс, скорость передачи данных	33,6 Кбит/с
Память	30 000
Проводная трубка
Автоответчик
Беспроводная трубка
Спикерфон
Caller ID
Стандарт DECT
АОН
Языки управления
PCL 6
PostScript
PostScript 3
PCL 5c
PCL 5e
PDF
Емкость лотка ручной подачи	150
Подача бумаги
Максимальная	6 350
Стандартная	1 200
Вывод бумаги
Максимальный	3 250
Стандартный	350
Версия USB	2,0
USB
Ethernet (RJ-45)
Bluetooth
Wi-Fi
Устройство для чтения карт памяти
Инфракрасный порт
FireWire (IEEE 1394)
AirPrint
LPT
Частота процессора	1 750
Емкость жесткого диска	250
Объем памяти	4 096
Работа от аккумулятора
Диагональ дисплея	10,1
Экран
Поддержка ОС
Mac OS
Windows
Потребляемая мощность
В режиме ожидания	67,9
При работе	849
Ширина	950
Глубина	620
Вес	142
Высота	742

Error code:	001-0001-05
Description:	Fixing Thermistor high temperature detection error
Causes:	The Fixing Film Unit Main Thermistor detected an abnormally high temperature.
Remedy:	[Related parts] R1.00 - Harnesses connecting the Pickup Driver PCB (UN4/J1491), the Drawer Unit (J8001) and the Fixing Thermistor Unit 1 (THM11/J7404) - Fixing Film Unit - Pickup Driver PCB (UN4) [Remedy] Perform the following in the order while checking whether the error is cleared. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. 1. Check the harness between the Pickup Driver PCB and the Fixing Film Unit Main Thermistor. 2. Pull out the Fixing Feed Unit and check "FIX-UC". a. In the case of below 240 deg C, replace the Fixing Film Unit. b. In the case of 240 deg C or higher, disconnect the connector of the Pickup Driver PCB and then check "FIX-UC" again. b-a. In the case of below 240 deg C, replace the harness between the Pickup Driver PCB and the Drawer Unit. b-b. In the case of 240 deg C or higher, replace the Pickup Driver PCB.

Error code:	001-0002-05
Description:	Fixing Thermistor high temperature detection error
Causes:	The Fixing Main Thermistor in the Fixing Assembly detected 230 deg C or higher.
Remedy:	[Related parts] - Harness between the Main Driver PCB (UN78/J129, J104 and J105) and the Fixing Drawer Unit (J3001) (Unit of replacement: CABLE, FIXING DRAWER) - Harness between the Fixing Thermistor (THM01/J3271, THM02/J3206 and THM04/J3204) and the Fixing Drawer Unit (J3200) (Unit of replacement: CABLE, FIXING DC DRAWER) - Harnesses from the Main Driver PCB to the Fixing Power Supply PCB 1. Main Driver PCB (UN78/J118 and J119) to Relay Connector (19P and 13P) (Unit of replacement: CABLE, MAIN DRIVER IH) 2. Relay Connector (19P and 13P) to Fixing Power Supply PCB (UN03/J316 and J313) (Unit of replacement: CABLE, IH SIGNAL) - Harness between the Main Driver PCB (UN78/J108 and J101) and the Relay PCB (UN86/J522 and J515) (Unit of replacement: CABLE, SIGNAL) - Harness between the DC Controller PCB (UN01/J414, J411, J412 and J413) and the Main Driver PCB (UN78/J128, J126, J125 and J124) (Unit of replacement: CABLE, SIGNAL) - Fixing Main Thermistor (THM01) (Unit of replacement: THERMISTOR UNIT, MAIN) - Fixing Sub Thermistor 1 and 2 (THM02 and THM04) (Unit of replacement: THERMISTOR UNIT, SUB) - Fixing Upper Unit (Unit of replacement: FIXING ASS`Y, UPPER) - Fixing Power Supply PCB (UN03) (Unit of replacement: IH POWER SUPPLY PCB ASS`Y) - Main Driver PCB (UN78) (Unit of replacement: MAIN DRIVE DRIVER PCB ASS`Y) - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	001-0003-05
Description:	Fixing Thermistor high temperature detection error
Causes:	The FixingThermistor detects hardware overheating.
Remedy:	[Related parts] - Harness between the Main Driver PCB (UN78/J129, J104 and J105) and the Fixing Drawer Unit (J3001) (Unit of replacement: CABLE, FIXING DRAWER) - Harness between the Fixing Thermistor (THM01/J3271, THM02/J3206 and THM04/J3204) and the Fixing Drawer Unit (J3200) (Unit of replacement: CABLE, FIXING DC DRAWER) - Harnesses from the Main Driver PCB to the Fixing Power Supply PCB 1. Main Driver PCB (UN78/J118 and J119) to Relay Connector (19P and 13P) (Unit of replacement: CABLE, MAIN DRIVER IH) 2. Relay Connector (19P and 13P) to Fixing Power Supply PCB (UN03/J316 and J133) (Unit of replacement: CABLE, IH SIGNAL) - Harness between the Main Driver PCB (UN78/J108 and J101) and the Relay PCB (UN86/J522 and J515) (Unit of replacement: CABLE, SIGNAL) - Harness between the DC Controller PCB (UN01/J414, J411, J412 and J413) and the Main Driver PCB (UN78/J128, J126, J125 and J124) (Unit of replacement: CABLE, SIGNAL) - Fixing Main Thermistor (THM01) (Unit of replacement: THERMISTOR UNIT, MAIN) - Fixing Sub Thermistor 1 and 2 (THM02 and THM04) (Unit of replacement: THERMISTOR UNIT, SUB) - Fixing Upper Unit (Unit of replacement: FIXING ASS`Y, UPPER) - Fixing Power Supply PCB (UN03) (Unit of replacement: IH POWER SUPPLY PCB ASS`Y) - Main Driver PCB (UN78) (Unit of replacement: MAIN DRIVE DRIVER PCB ASS`Y) - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	001-0004-05
Description:	Fixing Thermistor high temperature detection error
Causes:	Abnormal temperature difference among the Thermistors was detected.
Remedy:	[Related parts] - Harness between the Main Driver PCB (UN78/J129, J104 and J105) and the Fixing Drawer Unit (J3001) (Unit of replacement: CABLE, FIXING DRAWER) - Harness between the Fixing Thermistor (THM01/J3271, THM02/J3206 and THM04/J3204) and the Fixing Drawer Unit (J3200) (Unit of replacement: CABLE, FIXING DC DRAWER) - Harnesses from the Main Driver PCB to the Fixing Power Supply PCB 1. Main Driver PCB (UN78/J118 and J119) to Relay Connector (19P and 13P) (Unit of replacement: CABLE, MAIN DRIVER IH) 2. Relay Connector (19P and 13P) to Fixing Power Supply PCB (UN03/J316 and J313) (Unit of replacement: CABLE, IH SIGNAL) - Harness between the Main Driver PCB (UN78/J108 and J101) and the Relay PCB (UN86/J522 and J515) (Unit of replacement: CABLE, SIGNAL) - Harness between the DC Controller PCB (UN01/J414, J411, J412 and J413) and the Main Driver PCB (UN78/J128, J126, J125 and J124) (Unit of replacement: CABLE, SIGNAL) - Fixing Main Thermistor (THM01) (Unit of replacement: THERMISTOR UNIT, MAIN) - Fixing Sub Thermistor 1 and 2 (THM02 and THM04) (Unit of replacement: THERMISTOR UNIT, SUB) - Fixing Upper Unit (Unit of replacement: FIXING ASS`Y, UPPER) - Fixing Power Supply PCB (UN03) (Unit of replacement: IH POWER SUPPLY PCB ASS`Y) - Main Driver PCB (UN78) (Unit of replacement: MAIN DRIVE DRIVER PCB ASS`Y) - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	001-0005-05
Description:	Fixing Thermistor high temperature detection error
Causes:	The Fixing Film Thermistor (Front) detected a high temperature error.
Remedy:	[Related parts] R1.00 - Harness connecting from the Feed/Drum Driver PCB (UN2/J213) to the Fixing Cooling Fan (Front) and (Rear) (FM5/J6068 and FM6/J6069) - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Sub Thermistor (TH2/J6491) - Fixing Cooling Fan (Front) (FM5) - Fixing Cooling Fan (Rear) (FM6) - Sub Thermistor (TH2) - Film Assembly - Fan Shutter - Feed/Drum Driver PCB (UN2) - DC Controller PCB (UN1) [Remedy] - Check COPIER> DISPLAY> ANALOG> FIX-F. a. In the case of below 275 deg C, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. b. In the case of 275 deg C or higher, check/replace the related harness/cable, connector and parts. [CAUTION] Do not turn ON the power before replacing the Fixing Film Unit. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	001-0006-05
Description:	Fixing Thermistor high temperature detection error
Causes:	The Fixing Film Thermistor (Rear) detected a high temperature error.
Remedy:	[Related parts] R1.00 - Harness connecting from the Feed/Drum Driver PCB (UN2/J213) to the Fixing Cooling Fan (Front) and (Rear) (FM5/J6068 and FM6/J6069) - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Sub Thermistor (TH2/J6491) - Fixing Cooling Fan (Front) (FM5) - Fixing Cooling Fan (Rear) (FM6) - Sub Thermistor (TH2) - Film Assembly - Fan Shutter - Feed/Drum Driver PCB (UN2) - DC Controller PCB (UN1) [Remedy] - Check COPIER> DISPLAY> ANALOG> FIX-R. a. In the case of below 275 deg C, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. b. In the case of 275 deg C or higher, check/replace the related harness/cable, connector and parts. [CAUTION] Do not turn ON the power before replacing the Fixing Film Unit. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	001-0007-05
Description:	Fixing Thermistor high temperature detection error
Causes:	The Fixing Thermistor detected a high temperature error by hardware detection.
Remedy:	[Related parts] R1.00 - Harness connecting from the Feed/Drum Driver PCB (UN2/J213) to the Fixing Cooling Fan (Front) and (Rear) (FM5/J6068 and FM6/J6069) - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Fixing Thermistors (TH2/J6491 and TH1/J6492) - Fixing Cooling Fan (Front) (FM5) - Fixing Cooling Fan (Rear) (FM6) - Fixing Thermistors (TH1 and TH2) - Film Assembly - Fan Shutter - Feed/Drum Driver PCB (UN2) - DC Controller PCB (UN1) [Remedy] - Check the detected temperatures of all the Fixing Thermistors. a. If it is the upper limit temperature or lower, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. b. If it exceeds the upper limit temperature, check/replace the related harness/cable, connector and parts. [CAUTION] Do not turn ON the power before replacing the Fixing Film Unit. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0001-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	After the start of temperature control of the Fixing Roller, the Fixing Main Thermistor detected abnormal temperature rise.
Remedy:	[Related parts] - Harness between the Main Driver PCB (UN78/J129, J104 and J105) and the Fixing Drawer Unit (J3001) (Unit of replacement: CABLE, FIXING DRAWER) - Harness between the Fixing Main Thermistor (THM01/J3271) and the Fixing Drawer Unit (J3200) (Unit of replacement: CABLE, FIXING DC DRAWER) - Harnesses from the Main Driver PCB to the Fixing Power Supply PCB 1. Main Driver PCB (UN78/J118 and J119) to Relay Connector (19P and 13P) (Unit of replacement: CABLE, MAIN DRIVER IH) 2. Relay Connector (19P and 13P) to Fixing Power Supply PCB (UN03/J316 and J313) (Unit of replacement: CABLE, IH SIGNAL) - Harness between the Main Driver PCB (UN78/J108 and J101) and the Relay PCB (UN86/J522 and J515) (Unit of replacement: CABLE, SIGNAL) - Harness between the DC Controller PCB (UN01/J414, J411, J412 and J413) and the Main Driver PCB (UN78/J128, J126, J125 and J124) (Unit of replacement: CABLE, SIGNAL) - Fixing Main Thermistor (THM01) (Unit of replacement: THERMISTOR UNIT, MAIN) - Fixing Upper Unit (Unit of replacement: FIXING ASS`Y, UPPER) - Fixing Power Supply PCB (UN03) (Unit of replacement: IH POWER SUPPLY PCB ASS`Y) - Main Driver PCB (UN78) (Unit of replacement: MAIN DRIVE DRIVER PCB ASS`Y) - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0002-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	Startup control was not completed although 60 sec had passed.
Remedy:	[Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Main Thermistor (TH1/J6492) - Main Thermistor (TH1) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0003-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	After the Fixing Heater was turned ON, the Fixing Main Thermistor detected error in temperature increase.
Remedy:	[Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Main Thermistor (TH1/J6492) - Main Thermistor (TH1) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0004-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	After the Fixing Heater was turned ON, the Fixing Thermistor (Front) detected error in temperature increase.
Remedy:	[Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Main Thermistor (TH1/J6492) - Main Thermistor (TH1) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0005-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	After the Fixing Heater was turned ON, the Fixing Thermistor (Rear) detected error in temperature increase.
Remedy:	[Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Main Thermistor (TH1/J6492) - Main Thermistor (TH1) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0006-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	The Fixing Film Thermistor (Middle) detected no temperature increase.
Remedy:	[Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Main Thermistor (TH1/J6492) - Main Thermistor (TH1) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0007-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	The Fixing Film Thermistor (Front) detected no temperature increase.
Remedy:	[Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Sub Thermistor (TH2/J6491) - Sub Thermistor (TH2) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0008-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	The Fixing Film Thermistor (Rear) detected no temperature increase.
Remedy:	[Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Sub Thermistor (TH2/J6491) - Sub Thermistor (TH2) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0009-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	The Fixing Film Thermistor (Middle) detected error in temperature increase.
Remedy:	[Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Main Thermistor (TH1/J6492) - Main Thermistor (TH1) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	002-0010-05
Description:	Fixing Thermistor low temperature detection error
Causes:	Turning OFF and then ON the power without clearing the error.
Remedy:	Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR.

Error code:	002-0011-05
Description:	Fixing Thermistor temperature increase detection error
Causes:	The Fixing Film Thermistor (Rear) detected error in temperature increase.
Remedy:	[Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Sub Thermistor (TH2/J6491) - Sub Thermistor (TH2) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	003-0001-05
Description:	Fixing Thermistor low temperature detection error
Causes:	The Fixing Film Unit Main Thermistor detected an abnormally low temperature during print control.
Remedy:	[Related parts] R1.00 - Harness between the Pickup Driver PCB (UN4/J1489) and the IH Power Supply PCB (UN30/ J501) - Harnesses connecting the IH Power Supply PCB (UN30/J510), the Drawer Unit (J8027) and the Main Heater (H4) - Harnesses connecting the Pickup Driver PCB (UN4/J1491), the Drawer Unit (J8001) and the Fixing Thermistor Unit 1 (THM11/J7404) - Main Heater (H4) - Fixing Film Unit - IH Power Supply PCB (UN30) - Pickup Driver PCB (UN4) [Remedy] Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR.

Error code:	003-0002-05
Description:	Fixing Thermistor low temperature detection error
Causes:	The Fixing Sub Thermistor (Front) detected an abnormally low temperature during print control.
Remedy:	- Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Main Thermistor (TH1/J6492) - Main Thermistor (TH1) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	003-0003-05
Description:	Fixing Thermistor low temperature detection error
Causes:	The Fixing Sub Thermistor (Rear) detected an abnormally low temperature during print control.
Remedy:	- Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Main Thermistor (TH1/J6492) - Main Thermistor (TH1) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	003-0004-05
Description:	Fixing Thermistor low temperature detection error
Causes:	The Fixing Film Thermistor (Middle) detected an abnormally low temperature during print control.
Remedy:	- Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Main Thermistor (TH1/J6492) - Main Thermistor (TH1) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	003-0005-05
Description:	Fixing Thermistor low temperature detection error
Causes:	The Fixing Film Thermistor (Front) detected an abnormally low temperature during print control.
Remedy:	- Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Sub Thermistor (TH2/J6491) - Sub Thermistor (TH2) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	003-0006-05
Description:	Fixing Thermistor low temperature detection error
Causes:	The Fixing Film Thermistor (Rear) detected an abnormally low temperature during print control.
Remedy:	- Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Sub Thermistor (TH2/J6491) - Sub Thermistor (TH2) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	003-0007-05
Description:	Fixing Thermistor low temperature detection error
Causes:	An error in temperature difference between the Fixing Film Thermistor (Front) and (Rear) was detected during print control.
Remedy:	- Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Sub Thermistor (TH2/J6491) - Sub Thermistor (TH2) - Film Assembly - Fan Shutter - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. Then, turn OFF and then ON the main power. 2. Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	004-0000-05
Description:	Fixing Thermistor disconnection detection error
Causes:	Open circuit of the Fixing Thermistor or connector disconnection was detected.
Remedy:	- Harnesses connecting the DC Controller PCB (UN1/J122), the Drawer Unit (J5012) and the Fixing Thermistors (TH1/J6492 and TH2/J6491) - Fixing Thermistors (TH1 and TH2) - Film Assembly - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Fixing Assembly is properly installed. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	004-0001-05
Description:	Fixing Power Supply error
Causes:	An error in the fixing current was detected.
Remedy:	[Related parts] - Harnesses from the Main Driver PCB to the Fixing Power Supply PCB 1. Main Driver PCB (UN78/J118 and J119) to Relay Connector (19P and 13P) (Unit of replacement: CABLE, MAIN DRIVER IH) 2. Relay Connector (19P and 13P) to Fixing Power Supply PCB (UN03/J316 and J313) (Unit of replacement: CABLE, IH SIGNAL) - Fixing Power Supply PCB (UN03) (Unit of replacement: IH POWER SUPPLY PCB ASS`Y) - Main Driver PCB (UN78) (Unit of replacement: MAIN DRIVE DRIVER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR.

Error code:	009-0000-05
Description:	Fixing pressure timeout error
Causes:	The Fixing Pressure Sensor did not detect ON status within 5 sec after the start of pressure application operation for fixing.
Remedy:	- Harness between the Feed/Drum Driver PCB (UN2/J215) and the Fixing Motor (M21/J6084) - Harness between the DC Controller PCB (UN1/J172 and J170) and the Feed/Drum Driver PCB (UN2/J203 and J202) - Feed/Drum Driver PCB (UN2) - Fixing Motor (M21) - Fixing Drive Assembly - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power. 2. Check that the Fixing Assembly is properly installed. 3. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	009-0001-05
Description:	Fixing disengagement timeout error
Causes:	The Fixing Pressure Sensor did not detect OFF status within 5 sec after the start of fixing disengagement operation.
Remedy:	- Harness between the Feed/Drum Driver PCB (UN2/J215) and the Fixing Motor (M21/J6084) - Harness between the DC Controller PCB (UN1/J172 and J170) and the Feed/Drum Driver PCB (UN2/J203 and J202) - Feed/Drum Driver PCB (UN2) - Fixing Motor (M21) - Fixing Drive Assembly - DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power. 2. Check that the Fixing Assembly is properly installed. 3. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	009-0002-05
Description:	Fixing pressure error
Causes:	The gears did not stop at pressure application position within 10 times after the start of pressure application operation for fixing.
Remedy:	Clean the grease scattered on the gears in the Fixing Assembly. 1. Remove the Fixing Assembly and the Pressure Release Plate Assembly. 2. Wipe off the grease scattered on/around the Pressure Release Cam and the Pressure Plate with lint-free paper moistened with alcohol. 3. Wipe off the excess grease on the side of the gears and shaft in the host machine.

Error code:	012-0101-05
Description:	Drum speed detection error (Y)
Causes:	The Drum Speed Detection PCB (Y) 1/2 detected a rotation signal error.
Remedy:	[Related parts] R1.00 - Harness connecting from the Drum Driver PCB (UN6/J1905) to the Drum Speed Detection PCB (Y) 1/2 and Drum Motor (Y) (UN20/J7316, UN21/J7317 and M21/J7300) - Drum Speed Detection PCB (Y) 1/2 (UN20 and UN21) - Drum Motor (Y) (M21) - Drum Unit (Y) - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Encoder Wheel of the Drum Speed Detection PCB (Y) 1/2 is properly installed. 2. Clean the Drum Speed Detection PCB (Y) 1/2 and the Encoder Wheel. 3. Set the Drum Unit (Y) again. 4. Check/replace the related harness/cable, connector and parts.

Error code:	012-0401-05
Description:	Drum speed detection error (Bk)
Causes:	The Drum Speed Detection PCB (Bk) 1/2 detected a rotation signal error.
Remedy:	[Related parts] R1.00 - Harness connecting from the Drum Driver PCB (UN6/J1907) to the Drum Speed Detection PCB (Bk) 1/2 and Drum Motor (Bk) (UN18/J7310, UN19/J7311 and M19/J7306) - Drum Speed Detection PCB (Bk) 1/2 (UN18 and UN19) - Drum Motor (Bk) (M19) - Drum Unit (Bk) - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Encoder Wheel of the Drum Speed Detection PCB (Bk) 1/2 is properly installed. 2. Clean the Drum Speed Detection PCB (Bk) 1/2 and the Encoder Wheel. 3. Set the Drum Unit (Bk) again. 4. Check/replace the related harness/cable, connector and parts.

Error code:	012-1000-05
Description:	ITB Motor error
Causes:	Lock signal error of the ITB Motor was detected while the ITB was being driven.
Remedy:	- Harness between the Front Driver PCB (UN3/J303) and the ITB Motor (M13/J3030) - Harness between the Front Driver PCB (UN3/J304) and the Relay PCB (UN5/J402) - ITB Motor (M13) - Transfer Cleaning Blade - Front Driver PCB (UN3) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the ITB is not displaced. 2. Check/replace the related harness/cable, connector and parts.

Error code:	012-1001-05
Description:	ITB Motor error
Causes:	Lock signal error of the ITB was detected consecutively when starting the drive of the ITB.
Remedy:	- Harness between the Front Driver PCB (UN3/J303) and the ITB Motor (M13/J3030) - ITB Motor (M13) - Transfer Cleaning Blade - Front Driver PCB (UN3) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the ITB is not displaced. 2. Check/replace the related harness/cable, connector and parts.

Error code:	013-0001-05
Description:	Waste Toner Lock detection error
Causes:	The Waste Toner Lock Detection Switch detects locked at power-on.
Remedy:	[Related parts] - Harness between the Main Driver PCB (UN78/J103) and the Waste Toner Lock Detection Switch (SW05/J3050) (Unit of replacement: CABLE, MAIN DRIVER RELAY) - Waste Toner Lock Detection Switch (SW05) (Unit of replacement: CABLE, LOCK DETECT SWITCH) - Main Driver PCB (UN78) (Unit of replacement: MAIN DRIVE DRIVER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	013-0002-05
Description:	Waste Toner Lock detection error
Causes:	The Waste Toner Lock Detection Switch detects locked while the Developing Assembly is driven.
Remedy:	[Related parts] - Harness between the Main Driver PCB (UN78/J103) and the Waste Toner Lock Detection Switch (SW05/J3050) (Unit of replacement: CABLE, MAIN DRIVER RELAY) - Waste Toner Lock Detection Switch (SW05) (Unit of replacement: CABLE, LOCK DETECT SWITCH) - Main Driver PCB (UN78) (Unit of replacement: MAIN DRIVE DRIVER PCB ASS`Y) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the Waste Toner Container and the Waste Toner Pipe, and remove clogged toner if there is any. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	014-0001-05
Description:	Fixing Motor error
Causes:	Lock error of the Fixing Motor was detected.
Remedy:	[Related parts] - Harness between the Main Driver PCB (UN78/J104 and J105) and the Fixing Drawer Unit (J3001) (Unit of replacement: CABLE, FIXING DRAWER) - Harness between the Relay PCB (UN86/J520) and the Fixing Drawer Unit (J3218M) (Unit of replacement: CABLE, SIGNAL) - Harness between the Fixing Drawer Unit (J3200) and the Fixing Motor (M03/J2163P) (Unit of replacement: CABLE, FIXING MOTOR, 1) - Fixing Drive Unit (Unit of replacement: FIXING DRIVE ASS`Y) - Fixing Drive Gear (Unit of replacement: GEAR,71T/26T, GEAR, 20T, GEAR, 33T/20T, GEAR, 16T/38T) - Fixing Motor (M03) - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - Main Driver PCB (UN78) (Unit of replacement: MAIN DRIVE DRIVER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-0124-05
Description:	ATR output error
Causes:	The ATR Patch (Y) detected that the output value (SigD) was below the lower limit at initialization of the Developing Assembly.
Remedy:	- Drum Unit - Developing Assembly (Y) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Assembly and the Drum Unit are properly installed. 2. Remove soiling on the exposure window and the Drum Unit. 3. Replace the Developing Assembly and the Drum Unit.

Error code:	020-0134-05
Description:	ATR output error
Causes:	The ATR Patch (Y) detected that the output value (SigD) exceeded the upper limit at initialization of the Developing Assembly.
Remedy:	- Drum Unit - Developing Assembly (Y) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Assembly and the Drum Unit are properly installed. 2. Remove soiling on the Drum Unit. 3. Replace the Developing Assembly and the Drum Unit.

Error code:	020-01A8-05
Description:	Toner Density Sensor (Y) output upper/lower limit error
Causes:	Output (Vsig_ind) of the Toner Density Sensor (Y) showed 245 or higher or 10 or lower once during operation.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1305) and the Toner Density Sensor (Y) (TS2/ J8944) - Toner Density Sensor (Y) (TS2) - Side Driver PCB (UN96) - Developing Assembly (Y) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-01A9-05
Description:	ATR output error
Causes:	The ATR Sensor (Y) detected that the output value exceeded the upper limit during printing.
Remedy:	- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5093/5P) and the ATR Sensor (Y) (TS5/J6114) - Developing Assembly (Y) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-01B8-05
Description:	Toner Density Sensor (Y) output upper/lower limit error
Causes:	When executing the initial installation mode of the Developing Assembly (Y) (COPIER> FUNCTION> INSTALL> INISET-Y), output failed to reach 128 although the control voltage value of the Toner Density Sensor (Y) reached 1023 or higher. Or output failed to reach 128 although the control voltage reached 220 or lower.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1305) and the Toner Density Sensor (Y) (TS2/ J8944) - Toner Density Sensor (Y) (TS2) - Side Driver PCB (UN96) - Developing Assembly (Y) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-01B9-05
Description:	ATR output error
Causes:	The ATR Sensor (Y) detected 4.5 V or more of control voltage at initialization of the Developing Assembly.
Remedy:	- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5093/5P) and the ATR Sensor (Y) (TS5/J6114) - Developing Assembly (Y) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-0224-05
Description:	ATR output error
Causes:	The ATR Patch (M) detected that the output value (SigD) was below the lower limit at initialization of the Developing Assembly.
Remedy:	- Drum Unit - Developing Assembly (M) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Assembly and the Drum Unit are properly installed. 2. Remove soiling on the exposure window and the Drum Unit. 3. Replace the Developing Assembly and the Drum Unit.

Error code:	020-0234-05
Description:	ATR output error
Causes:	The ATR Patch (M) detected that the output value (SigD) exceeded the upper limit at initialization of the Developing Assembly.
Remedy:	- Drum Unit - Developing Assembly (M) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Assembly and the Drum Unit are properly installed. 2. Remove soiling on the Drum Unit. 3. Replace the Developing Assembly and the Drum Unit.

Error code:	020-02A8-05
Description:	Toner Density Sensor (M) output upper/lower limit error
Causes:	Output (Vsig_ind) of the Toner Density Sensor (M) showed 245 or higher or 10 or lower once during operation.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1305) and the Toner Density Sensor (M) (TS3/ J9014) - Toner Density Sensor (M) (TS3) - Side Driver PCB (UN96) - Developing Assembly (M) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-02A9-05
Description:	ATR output error
Causes:	The ATR Sensor (M) detected that the output value exceeded the upper limit during printing.
Remedy:	- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5094/5P) and the ATR Sensor (M) (TS6/J6116) - Developing Assembly (M) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-02B8-05
Description:	Toner Density Sensor (M) output upper/lower limit error
Causes:	When executing the initial installation mode of the Developing Assembly (M) (COPIER> FUNCTION> INSTALL> INISET-M), output failed to reach 128 although the control voltage value of the Toner Density Sensor (M) reached 1023 or higher. Or output failed to reach 128 although the control voltage reached 220 or lower.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1305) and the Toner Density Sensor (M) (TS3/ J9014) - Toner Density Sensor (M) (TS3) - Side Driver PCB (UN96) - Developing Assembly (M) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-02B9-05
Description:	ATR output error
Causes:	The ATR Sensor (M) detected 4.5 V or more of control voltage at initialization of the Developing Assembly.
Remedy:	- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5094/5P) and the ATR Sensor (M) (TS6/J6116) - Developing Assembly (M) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-0324-05
Description:	ATR output error
Causes:	The ATR Patch (C) detected that the output value (SigD) was below the lower limit at initialization of the Developing Assembly.
Remedy:	- Drum Unit - Developing Assembly (C) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Assembly and the Drum Unit are properly installed. 2. Remove soiling on the exposure window and the Drum Unit. 3. Replace the Developing Assembly and the Drum Unit.

Error code:	020-0334-05
Description:	ATR output error
Causes:	The ATR Patch (C) detected that the output value (SigD) exceeded the upper limit at initialization of the Developing Assembly.
Remedy:	- Drum Unit - Developing Assembly (C) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Assembly and the Drum Unit are properly installed. 2. Remove soiling on the Drum Unit. 3. Replace the Developing Assembly and the Drum Unit.

Error code:	020-03A8-05
Description:	Toner Density Sensor (C) output upper/lower limit error
Causes:	Output (Vsig_ind) of the Toner Density Sensor (C) showed 245 or higher or 10 or lower once during operation.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1309) and the Toner Density Sensor (C) (TS4/ J9015) - Toner Density Sensor (C) (TS4) - Side Driver PCB (UN96) - Developing Assembly (C) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-03A9-05
Description:	ATR output error
Causes:	The ATR Sensor (C) detected that the output value exceeded the upper limit during printing.
Remedy:	- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5095/5P) and the ATR Sensor (C) (TS7/J6118) - Developing Assembly (C) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-03B8-05
Description:	Toner Density Sensor (C) output upper/lower limit error
Causes:	When executing the initial installation mode of the Developing Assembly (C) (COPIER> FUNCTION> INSTALL> INISET-C), output failed to reach 128 although the control voltage value of the Toner Density Sensor (C) reached 1023 or higher. Or output failed to reach 128 although the control voltage reached 220 or lower.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1309) and the Toner Density Sensor (C) (TS4/ J9015) - Toner Density Sensor (C) (TS4) - Side Driver PCB (UN96) - Developing Assembly (C) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-03B9-05
Description:	ATR output error
Causes:	The ATR Sensor (C) detected 4.5 V or more of control voltage at initialization of the Developing Assembly.
Remedy:	- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5095/5P) and the ATR Sensor (C) (TS7/J6118) - Developing Assembly (C) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-0424-05
Description:	ATR output error
Causes:	The ATR Patch (Bk) detected that the output value (SigD) was below the lower limit at initialization of the Developing Assembly.
Remedy:	- Drum Unit - Developing Assembly (Bk) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Assembly and the Drum Unit are properly installed. 2. Remove soiling on the exposure window and the Drum Unit. 3. Replace the Developing Assembly and the Drum Unit.

Error code:	020-0434-05
Description:	ATR output error
Causes:	The ATR Patch (Bk) detected that the output value (SigD) exceeded the upper limit at initialization of the Developing Assembly.
Remedy:	- Drum Unit - Developing Assembly (Bk) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Assembly and the Drum Unit are properly installed. 2. Remove soiling on the Drum Unit. 3. Replace the Developing Assembly and the Drum Unit.

Error code:	020-04A8-05
Description:	Toner Density Sensor (Bk) output upper/lower limit error
Causes:	Output (Vsig_ind) of the Toner Density Sensor (Bk) showed 245 or higher or 10 or lower once during operation.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1309) and the Toner Density Sensor (Bk) (TS1/ J9016) - Toner Density Sensor (Bk) - Side Driver PCB (UN96) - Developing Assembly (Bk) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-04A9-05
Description:	ATR output error
Causes:	The ATR Sensor (Bk) detected that the output value exceeded the upper limit during printing.
Remedy:	- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5096/5P) and the ATR Sensor (Bk) (TS8/J6120) - Developing Assembly (Bk) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-04B8-05
Description:	Toner Density Sensor (Bk) output upper/lower limit error
Causes:	When executing the initial installation mode of the Developing Assembly (Bk) (COPIER> FUNCTION> INSTALL> INISET-K), output failed to reach 128 although the control voltage value of the Toner Density Sensor (Bk) reached 1023 or higher. Or output failed to reach 128 although the control voltage reached 220 or lower.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1309) and the Toner Density Sensor (Bk) (TS1/ J9016) - Toner Density Sensor (Bk) - Side Driver PCB (UN96) - Developing Assembly (Bk) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	020-04B9-05
Description:	ATR output error
Causes:	The ATR Sensor (Bk) detected 4.5 V or more of control voltage at initialization of the Developing Assembly.
Remedy:	- Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5096/5P) and the ATR Sensor (Bk) (TS8/J6120) - Developing Assembly (Bk) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	021-0100-05
Description:	Developing Motor error
Causes:	Lock signal error of the Developing Motor (Y) was detected consecutively.
Remedy:	- Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (Y) (M5/ J6015) - Developing Motor (Y) (M5) - Developing Assembly (Y) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn the gears of the Developing Assembly by hand. If it does not turn, replace the Developing Assembly. 2. Check/replace the related harness/cable, connector and parts.

Error code:	021-0120-05
Description:	Developing Screw rotation detection error
Causes:	The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (Y) in the Developing Assembly (Y) was 12 or less during rotation of the Developing Screw.
Remedy:	- Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (Y) (M5/ J6015) - Harnesses connecting the Front Driver PCB (UN3/J306), the Drawer Unit (J755) and the Process Unit Relay PCB (UN20/J607) - Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5093/5P) and the ATR Sensor (Y) (TS5/J6114) - Developing Motor (Y) (M5) - Developing Assembly (Y) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	021-0200-05
Description:	Developing Motor error
Causes:	Lock signal error of the Developing Motor (M) was detected consecutively.
Remedy:	- Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (M) (M6/ J6013) - Developing Motor (M) (M6) - Developing Assembly (M) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn the gears of the Developing Assembly by hand. If it does not turn, replace the Developing Assembly. 2. Check/replace the related harness/cable, connector and parts.

Error code:	021-0220-05
Description:	Developing Screw rotation detection error
Causes:	The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (M) in the Developing Assembly (M) was 12 or less during rotation of the Developing Screw.
Remedy:	- Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (M) (M6/ J6013) - Harnesses connecting the Front Driver PCB (UN3/J306), the Drawer Unit (J755) and the Process Unit Relay PCB (UN20/J607) - Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5094/5P) and the ATR Sensor (M) (TS6/J6116) - Developing Motor (M) (M6) - Developing Assembly (M) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	021-0300-05
Description:	Developing Motor error
Causes:	Lock signal error of the Developing Motor (C) was detected consecutively.
Remedy:	- Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (C) (M7/ J6012) - Developing Motor (C) (M7) - Developing Assembly (C) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn the gears of the Developing Assembly by hand. If it does not turn, replace the Developing Assembly. 2. Check/replace the related harness/cable, connector and parts.

Error code:	021-0320-05
Description:	Developing Screw rotation detection error
Causes:	The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (C) in the Developing Assembly (C) was 12 or less during rotation of the Developing Screw.
Remedy:	- Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (C) (M7/ J6012) - Harnesses connecting the Front Driver PCB (UN3/J306), the Drawer Unit (J755) and the Process Unit Relay PCB (UN20/J607) - Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5095/5P) and the ATR Sensor (C) (TS7/J6118) - Developing Motor (C) (M7) - Developing Assembly (C) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	021-0400-05
Description:	Developing Motor error
Causes:	Lock signal error of the Developing Motor (Bk) was detected consecutively.
Remedy:	[Related parts] R1.00 - Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (Bk) (M8/ J6011) - Developing Motor (Bk) (M8) - Developing Assembly (Bk) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn the gears of the Developing Assembly by hand. If it does not turn, replace the Developing Assembly. 2. Check/replace the related harness/cable, connector and parts.

Error code:	021-0420-05
Description:	Developing Screw rotation detection error
Causes:	The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (Bk) in the Developing Assembly (Bk) was 12 or less during rotation of the Developing Screw.
Remedy:	[Related parts] R1.01 - Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (Bk) (M8/ J6011) - Harnesses connecting the Front Driver PCB (UN3/J306), the Drawer Unit (J755) and the Process Unit Relay PCB (UN20/J607) - Harnesses connecting the Process Unit Relay PCB (UN20/J609), the Relay Connector (J5096/5P) and the ATR Sensor (Bk) (TS8/J6120) - Developing Motor (Bk) (M8) - Developing Assembly (Bk) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	025-0100-05
Description:	Toner Bottle Motor error
Causes:	Rotation error of the Toner Bottle Motor (Y) was detected.
Remedy:	[Related parts] R1.00 - Harness between the Feed/Drum Driver PCB (UN2/J211) and the Bottle Motor (Y) (M9/J2111) - Harness between the Feed/Drum Driver PCB (UN2/J212) and the Toner Sensor Relay PCB (Y) (UN39/J1400) - Harness between the Toner Sensor Relay PCB (Y) (UN39/J1401) and the Bottle Rotation Sensor (Y) (PS60/J6035) - Bottle Rotation Sensor (Y) (PS60) - Bottle Motor (Y) (M9) - Toner Bottle (Y) - Set-on Hopper Assembly - Toner Sensor Relay PCB (Y) (UN39) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn the Toner Bottle counterclockwise by hand, and if turning becomes heavy, check/replace the Toner Bottle. 2. Turn the Bottle Drive Gear of the Set-on Hopper Assembly by hand, and if turning becomes heavy, check/replace the assembly. 3. Check/replace the related harness/cable, connector and parts.

Error code:	025-0150-05
Description:	Toner Density Sensor (Y) output lower limit error
Causes:	The Toner Density Sensor (Y) detected that the output (Vsig_ind) was 51 or less 10 consecutive times.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1305) and the Toner Density Sensor (Y) (TS2/ J8944) - Harness between the DC Controller PCB (UN2/J1247) and the Hopper and Stirring Supply Motor (Y) (M9/J7104) - Toner Density Sensor (Y) (TS2) - Hopper and Stirring Supply Motor (Y) (M9) - Hopper Unit (Y) - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-0151-05
Description:	Toner Density Sensor (Y) output upper limit error
Causes:	The Toner Density Sensor (Y) detected that the output (Vsig_ind) was 221 or higher 10 consecutive times.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1305) and the Toner Density Sensor (Y) (TS2/ J8944) - Harness between the Video PCB (UN106/J70) and the Laser Scanner Unit (Y) - Harness between the DC Controller PCB (UN2/J1254) and the Developing High Voltage PCB (CL) (UN40/J3045) - Harness between the Primary Charging High Voltage PCB (CL) (UN38/J3022) and the HVR PCB (Y) (UN59) - Harness between the DC Controller PCB (UN2/J1247) and the Hopper Toner Level Sensor (Y) (TS6/J7121) - Toner Density Sensor (Y) (TS2) - Hopper Toner Level Sensor (Y) (TS6) - Laser Scanner Unit (Y) - Developing High Voltage PCB (CL) (UN40) - HVR PCB (Y) (UN59) - Primary Charging High Voltage PCB (CL) (UN38) - DC Controller PCB (UN2) - Hopper Unit (Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-01C0-05
Description:	Toner Container Replacement Cover open/close detection error (Y)
Causes:	The Toner Container Replacement Door Sensor (Y) did not detect the open state when removing the Toner Container.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1310) and the Toner Container Replacement Door Sensor (Y) (PS10/J7122) - Toner Container Replacement Door Sensor (Y) (PS10) - Hopper Unit (Y) - Toner Container Replacement Cover Unit - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. 1. Go through the following to check that the Toner Container Replacement Cover opens: Adjustment/Maintenance> Maintenance> Replace Specified Toner> Replace. Not Needed> Remove Toner. 2. Check the installation of the Toner Container Replacement Door Sensor (Y) and whether it is soiled. 3. Check that the Toner Container Replacement Cover opens by making the Hopper Unit driven with the Toner Container Removing Tool. If it`s in normal state, the output value of "COPIER> I/O> DC-CON> P035 bit7" shows "0" when opening the cover, and "1" when closing it with your hand. a. When the Toner Container Replacement Cover does not open although the Hopper Unit is driven, check the drive system (Hopper Unit and link mechanism of Hopper Tray). b. If the output value is not changed properly although the Toner Container Replacement Cover can be opened/closed, check/replace the related harness/cable, connector and parts. After a recovery from the error, go through the following to check that toner can be replaced properly (the removed toner container can be installed again): "Adjustment/Maintenance> Maintenance> Replace Specified Toner". [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-0200-05
Description:	Toner Bottle Motor error
Causes:	Rotation error of the Toner Bottle Motor (M) was detected.
Remedy:	[Related parts] R1.00 - Harness between the Feed/Drum Driver PCB (UN2/J211) and the Bottle Motor (M) (M10/J2112) - Harness between the Feed/Drum Driver PCB (UN2/J212) and the Toner Sensor Relay PCB (M) (UN40/J1410) - Harness between the Toner Sensor Relay PCB (M) (UN40/J1411) and the Bottle Rotation Sensor (M) (PS61/J6038) - Bottle Rotation Sensor (M) (PS61) - Bottle Motor (M) (M10) - Toner Bottle (M) - Set-on Hopper Assembly - Toner Sensor Relay PCB (M) (UN40) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn the Toner Bottle counterclockwise by hand, and if turning becomes heavy, check/replace the Toner Bottle. 2. Turn the Bottle Drive Gear of the Set-on Hopper Assembly by hand, and if turning becomes heavy, check/replace the assembly. 3. Check/replace the related harness/cable, connector and parts.

Error code:	025-0250-05
Description:	Toner Density Sensor (M) output lower limit error
Causes:	The Toner Density Sensor (M) detected that the output (Vsig_ind) was 51 or less 10 consecutive times.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1305) and the Toner Density Sensor (M) (TS3/ J9014) - Harness between the DC Controller PCB (UN2/J1247) and the Hopper and Stirring Supply Motor (M) (M12/J7105) - Toner Density Sensor (M) (TS3) - Hopper and Stirring Supply Motor (M) (M12) - Hopper Unit (M) - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-0251-05
Description:	Toner Density Sensor (M) output upper limit error
Causes:	The Toner Density Sensor (M) detected that the output (Vsig_ind) was 221 or higher 10 consecutive times.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1305) and the Toner Density Sensor (M) (TS3/ J9014) - Harness between the Video PCB (UN106/J70) and the Laser Scanner Unit (M) - Harness between the DC Controller PCB (UN2/J1254) and the Developing High Voltage PCB (CL) (UN40/J3045) - Harness between the Primary Charging High Voltage PCB (CL) (UN38/J3322) and the HVR PCB (M) (UN60) - Harness between the DC Controller PCB (UN2/J1247) and the Hopper Toner Level Sensor (M) (TS7/J7124) - Toner Density Sensor (M) (TS3) - Hopper Toner Level Sensor (M) (TS7) - Laser Scanner Unit (M) - Developing High Voltage PCB (CL) (UN40) - HVR PCB (M) (UN60) - Primary Charging High Voltage PCB (CL) (UN38) - DC Controller PCB (UN2) - Hopper Unit (Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-02C0-05
Description:	Toner Container Replacement Cover open/close detection error (M)
Causes:	The Toner Container Replacement Door Sensor (M) did not detect the open state when removing the Toner Container.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1310) and the Toner Container Replacement Door Sensor (M) (PS13/J7125) - Toner Container Replacement Door Sensor (M) (PS13) - Hopper Unit (M) - Toner Container Replacement Cover Unit - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. 1. Go through the following to check that the Toner Container Replacement Cover opens: Adjustment/Maintenance> Maintenance> Replace Specified Toner> Replace. Not Needed> Remove Toner. 2. Check the installation of the Toner Container Replacement Door Sensor (M) and whether it is soiled. 3. Check that the Toner Container Replacement Cover opens by making the Hopper Unit driven with the Toner Container Removing Tool. If it`s in normal state, the output value of "COPIER> I/O> DC-CON> P035 bit6" shows "0" when opening the cover, and "1" when closing it with your hand. a. When the Toner Container Replacement Cover does not open although the Hopper Unit is driven, check the drive system (Hopper Unit and link mechanism of Hopper Tray). b. If the output value is not changed properly although the Toner Container Replacement Cover can be opened/closed, check/replace the related harness/cable, connector and parts. After a recovery from the error, go through the following to check that toner can be replaced properly (the removed toner container can be installed again): "Adjustment/Maintenance> Maintenance> Replace Specified Toner". [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-0300-05
Description:	Toner Bottle Motor error
Causes:	Rotation error of the Toner Bottle Motor (C) was detected.
Remedy:	[Related parts] R1.00 - Harness between the Feed/Drum Driver PCB (UN2/J211) and the Bottle Motor (C) (M11/J2113) - Harness between the Feed/Drum Driver PCB (UN2/J212) and the Toner Sensor Relay PCB (C) (UN41/J1420) - Harness between the Toner Sensor Relay PCB (C) (UN41/J1421) and the Bottle Rotation Sensor (C) (PS62/J6041) - Bottle Rotation Sensor (C) (PS62) - Bottle Motor (C) (M11) - Toner Bottle (C) - Set-on Hopper Assembly - Toner Sensor Relay PCB (C) (UN41) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn the Toner Bottle counterclockwise by hand, and if turning becomes heavy, check/replace the Toner Bottle. 2. Turn the Bottle Drive Gear of the Set-on Hopper Assembly by hand, and if turning becomes heavy, check/replace the assembly. 3. Check/replace the related harness/cable, connector and parts.

Error code:	025-0350-05
Description:	Toner Density Sensor (C) output lower limit error
Causes:	The Toner Density Sensor (C) detected that the output (Vsig_ind) was 51 or less 10 consecutive times.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1309) and the Toner Density Sensor (C) (TS4/ J9015) - Harness between the DC Controller PCB (UN2/J1248) and the Hopper and Stirring Supply Motor (C) (M15/J7106) - Toner Density Sensor (C) (TS4) - Hopper and Stirring Supply Motor (C) (M15) - Hopper Unit (C) - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-0351-05
Description:	Toner Density Sensor (C) output upper limit error
Causes:	The Toner Density Sensor (C) detected that the output (Vsig_ind) was 221 or higher 10 consecutive times.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1309) and the Toner Density Sensor (C) (TS4/ J9015) - Harness between the Video PCB (UN106/J76) and the Laser Scanner Unit (C) - Harness between the DC Controller PCB (UN2/J1254) and the Developing High Voltage PCB (CL) (UN40/J3045) - Harness between the Primary Charging High Voltage PCB (CL) (UN38/J3522) and the HVR PCB (C) (UN61) - Harness between the DC Controller PCB (UN2/J1248) and the Hopper Toner Level Sensor (C) (TS8/J7127) - Toner Density Sensor (C) (TS4) - Hopper Toner Level Sensor (C) (TS8) - Laser Scanner Unit (C) - Developing High Voltage PCB (CL) (UN40) - HVR PCB (C) (UN61) - Primary Charging High Voltage PCB (CL) (UN38) - DC Controller PCB (UN2) - Hopper Unit (C) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-03C0-05
Description:	Toner Container Replacement Cover open/close detection error (C)
Causes:	The Toner Container Replacement Door Sensor (C) did not detect the open state when removing the Toner Container.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1310) and the Toner Container Replacement Door Sensor (C) (PS16/J7128) - Toner Container Replacement Door Sensor (C) (PS16) - Hopper Unit (C) - Toner Container Replacement Cover Unit - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. 1. Go through the following to check that the Toner Container Replacement Cover opens: Adjustment/Maintenance> Maintenance> Replace Specified Toner> Replace. Not Needed> Remove Toner. 2. Check the installation of the Toner Container Replacement Door Sensor (C) and whether it is soiled. 3. Check that the Toner Container Replacement Cover opens by making the Hopper Unit driven with the Toner Container Removing Tool. If it`s in normal state, the output value of "COPIER> I/O> DC-CON> P035 bit6" shows "0" when opening the cover, and "1" when closing it with your hand. a. When the Toner Container Replacement Cover does not open although the Hopper Unit is driven, check the drive system (Hopper Unit and link mechanism of Hopper Tray). b. If the output value is not changed properly although the Toner Container Replacement Cover can be opened/closed, check/replace the related harness/cable, connector and parts. After a recovery from the error, go through the following to check that toner can be replaced properly (the removed toner container can be installed again): "Adjustment/Maintenance> Maintenance> Replace Specified Toner". [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-0400-05
Description:	Toner Bottle Motor error
Causes:	Rotation error of the Toner Bottle Motor (Bk) was detected.
Remedy:	[Related parts] R1.00 - Harness between the Feed/Drum Driver PCB (UN2/J211) and the Bottle Motor (Bk) (M12/J2114) - Harness between the Feed/Drum Driver PCB (UN2/J212) and the Toner Sensor Relay PCB (Bk) (UN42/J1430) - Harness between the Toner Sensor Relay PCB (Bk) (UN42/J1431) and the Bottle Rotation Sensor (Bk) (PS63/J6044) - Bottle Rotation Sensor (Bk) (PS63) - Bottle Motor (Bk) (M12) - Toner Bottle (Bk) - Set-on Hopper Assembly - Toner Sensor Relay PCB (Bk) (UN42) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn the Toner Bottle counterclockwise by hand, and if turning becomes heavy, check/replace the Toner Bottle. 2. Turn the Bottle Drive Gear of the Set-on Hopper Assembly by hand, and if turning becomes heavy, check/replace the assembly. 3. Check/replace the related harness/cable, connector and parts.

Error code:	025-0450-05
Description:	Toner Density Sensor (Bk) output lower limit error
Causes:	The Toner Density Sensor (Bk) detected that the output (Vsig_ind) was 51 or less 10 consecutive times.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1309) and the Toner Density Sensor (Bk) (TS1/ J9016) - Harness between the DC Controller PCB (UN2/J1248) and the Hopper and Stirring Supply Motor (Bk) (M6/J7107) - Toner Density Sensor (Bk) (TS1) - Hopper and Stirring Supply Motor (Bk) (M6) - Hopper Unit (Bk) - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-0451-05
Description:	Toner Density Sensor (Bk) output upper limit error
Causes:	The Toner Density Sensor (Bk) detected that the output (Vsig_ind) was 221 or higher 10 consecutive times.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1309) and the Toner Density Sensor (Bk) (TS1/ J9016) - Harness between the Video PCB (UN106/J76) and the Laser Scanner Unit (Bk) - Harness between the Developing High Voltage PCB (CL) (UN40/J3046) and the Developing High Voltage PCB (Bk) (UN39/J7) - Harness between the DC Controller PCB (UN2/J1254) and the Developing High Voltage PCB (CL) (UN40/J3045) - Harness between the DC Controller PCB (UN2/J1248) and the Hopper Toner Level Sensor (Bk) (TS5/J7136) - Toner Density Sensor (Bk) (TS1) - Hopper Toner Level Sensor (Bk) (TS5) - Laser Scanner Unit (Bk) - Developing High Voltage PCB (Bk) (UN39) - Developing High Voltage PCB (CL) (UN40) - Primary Charging High Voltage PCB (Bk) (UN37) - DC Controller PCB (UN2) - Hopper Unit (Bk) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	025-04C0-05
Description:	Toner Container Replacement Cover open/close detection error (Bk)
Causes:	The Toner Container Replacement Door Sensor (Bk) did not detect the open state when removing the Toner Container.
Remedy:	[Related parts] R1.00 - Harness between the Side Driver PCB (UN96/J1310) and the Toner Container Replacement Door Sensor (Bk) (PS7/J7138) - Toner Container Replacement Door Sensor (Bk) (PS7) - Hopper Unit (Bk) - Toner Container Replacement Cover Unit - Side Driver PCB (UN96) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. 1. Go through the following to check that the Toner Container Replacement Cover opens: Adjustment/Maintenance> Maintenance> Replace Specified Toner> Replace. Not Needed> Remove Toner. 2. Check the installation of the Toner Container Replacement Door Sensor (Bk) and whether it is soiled. 3. Check that the Toner Container Replacement Cover opens by making the Hopper Unit driven with the Toner Container Removing Tool. If it`s in normal state, the output value of "COPIER> I/O> DC-CON> P035 bit4" shows "0" when opening the cover, and "1" when closing it with your hand. a. When the Toner Container Replacement Cover does not open although the Hopper Unit is driven, check the drive system (Hopper Unit and link mechanism of Hopper Tray). b. If the output value is not changed properly although the Toner Container Replacement Cover can be opened/closed, check/replace the related harness/cable, connector and parts. After a recovery from the error, go through the following to check that toner can be replaced properly (the removed toner container can be installed again): "Adjustment/Maintenance> Maintenance> Replace Specified Toner". [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	027-0100-05
Description:	Error in supply with Y Developing Assembly
Causes:	The Toner Supply Screw Rotation Sensor detected rotation error within the specified period of time.
Remedy:	[Related parts] R1.01 - Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (Y) (M5/ J6015) - Harness between the Feed/Drum Driver PCB (UN2/J212) and the Toner Sensor Relay PCB (Y) (UN39/J1400) - Developing Motor (Y) (M5) - Developing Assembly (Y) - Main Drive Assembly - Set-on Hopper Assembly - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Coupling of the Developing Assembly is not damaged. 2. Check that the Developing Coupling of the Main Drive Assembly is not damaged. 3. Check/replace the related harness/cable, connector and parts.

Error code:	027-0200-05
Description:	Error in supply with M Developing Assembly
Causes:	The Toner Supply Screw Rotation Sensor detected rotation error within the specified period of time.
Remedy:	[Related parts] R1.01 - Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (M) (M6/ J6013) - Harness between the Feed/Drum Driver PCB (UN2/J212) and the Toner Sensor Relay PCB (M) (UN40/J1410) - Developing Motor (M) (M6) - Developing Assembly (M) - Main Drive Assembly - Set-on Hopper Assembly - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Coupling of the Developing Assembly is not damaged. 2. Check that the Developing Coupling of the Main Drive Assembly is not damaged. 3. Check/replace the related harness/cable, connector and parts.

Error code:	027-0300-05
Description:	Error in supply with C Developing Assembly
Causes:	The Toner Supply Screw Rotation Sensor detected rotation error within the specified period of time.
Remedy:	[Related parts] R1.01 - Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (C) (M7/ J6012) - Harness between the Feed/Drum Driver PCB (UN2/J212) and the Toner Sensor Relay PCB (C) (UN41/J1420) - Developing Motor (C) (M7) - Developing Assembly (C) - Main Drive Assembly - Set-on Hopper Assembly - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Coupling of the Developing Assembly is not damaged. 2. Check that the Developing Coupling of the Main Drive Assembly is not damaged. 3. Check/replace the related harness/cable, connector and parts.

Error code:	027-0400-05
Description:	Error in supply with K Developing Assembly
Causes:	The Toner Supply Screw Rotation Sensor detected rotation error within the specified period of time.
Remedy:	[Related parts] R1.01 - Harness between the Feed/Drum Driver PCB (UN2/J225) and the Developing Motor (Bk) (M8/ J6011) - Harness between the Feed/Drum Driver PCB (UN2/J212) and the Toner Sensor Relay PCB (Bk) (UN42/J1430) - Developing Motor (Bk) (M8) - Developing Assembly (Bk) - Main Drive Assembly - Set-on Hopper Assembly - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Developing Coupling of the Developing Assembly is not damaged. 2. Check that the Developing Coupling of the Main Drive Assembly is not damaged. 3. Check/replace the related harness/cable, connector and parts.

Error code:	029-1000-05
Description:	Patch Sensor error
Causes:	The Patch Sensor detected correction error of the light intensity value determined at initialization.
Remedy:	[Related parts] R1.00 - Harness between the Multi Driver PCB (UN97/J1353) and the Patch Sensor (PS21/J7412) - Patch Sensor (PS21) - Multi Driver PCB (UN97) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the sensor surface of the Patch Sensor is soiled, clean it with a cloth tightly wrung out of water. 2. Check/replace the related harness/cable, connector and parts.

Error code:	029-1001-05
Description:	Patch Sensor error
Causes:	An error was detected in P-wave light intensity value read by ITB background sampling.
Remedy:	[Related parts] R1.00 - Harness between the Multi Driver PCB (UN97/J1353) and the Patch Sensor (PS21/J7412) - Patch Sensor (PS21) - Intermediate Transfer Belt - Multi Driver PCB (UN97) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Intermediate Transfer Belt is free of damage and foreign matter. 2. If the sensor surface of the Patch Sensor is soiled, clean it with a cloth tightly wrung out of water. 3. Check/replace the related harness/cable, connector and parts.

Error code:	029-6001-05
Description:	Registration Shutter Solenoid error
Causes:	Light intensity lower limit error was detected during light intensity correction of the regular reflection LED.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J125) and the Patch Sensor (UN49/J1253) - Harness between the Front Driver PCB (UN3/J305) and the Registration Shutter Solenoid (SL1/ J6064) - Patch Sensor (UN49) - Registration Shutter Solenoid (SL1) - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	074-0001-05
Description:	Primary Transfer Roller disengagement HP timeout error
Causes:	The Primary Transfer Roller Detachment HP Sensor did not detect home position within the specified period of time.
Remedy:	[Related parts] R1.00 - Harness between the ITB Relay PCB (UN28/J2701) and the Primary Transfer Roller Detachment HP Sensor (PS4/J7113) - Harnesses connecting the DC Controller PCB (UN2/J1240), the Drawer Unit (J8050) and the ITB Relay PCB (UN28/J2700) - Primary Transfer Roller Detachment HP Sensor (PS4) - ITB Relay PCB (UN28) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Primary Transfer Roller (Pressure Release Lever, Link and Cam) is free of foreign matter or soiling. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	074-0002-05
Description:	ITB Unit pressure error
Causes:	When applying pressure on the ITB Unit (at power-on/recovery from sleep/opening and closing of the door), pressure failure was detected.
Remedy:	[Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the ITB Pressure Release Lever is in the engaged state. 2. When pulling out the ITB Unit, check that the unit is on the rails and the edges of the 2 ITB Pressure Arms at the front side of the unit are fitted in the grooves of the ITB Frame. [CAUTION] If the ITB Pressure Arm is soiled with toner, clean it with a cloth tightly wrung out of water. 3. Check that the shafts of the Primary Transfer Roller are fitted in the Shaft Support.

Error code:	074-0003-05
Description:	Primary Transfer Detachment Sensor error
Causes:	Both the Primary Transfer Detachment Sensor 1 and 2 detected home position at the same time during engagement/disengagement operation of the ITB.
Remedy:	[Related parts] R1.00 - Harnesses connecting the Front Driver PCB (UN3/J303), the ITB Displacement Sensor PCB (UN60/J700 and J701) and the Primary Transfer Detachment Sensor 1 and 2 (PS22/J7010 and PS23/J7011) - Primary Transfer Detachment Sensor 1 (PS22) - Primary Transfer Detachment Sensor 2 (PS23) - ITB Displacement Sensor PCB (UN60) - Intermediate Transfer Belt Assembly - Front Driver PCB (UN3) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	075-0002-05
Description:	ITB displacement control error
Causes:	The ITB Displacement Sensor detected upper limit error.
Remedy:	[Related parts] R1.00 - Harness between the ITB Relay PCB (UN28/J2702) and the ITB Displacement Sensor (PS2/ J7415) - ITB Displacement Sensor (PS2) - ITB Relay PCB (UN28) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the ITB Displacement Sensor and the Sensor Flag are properly installed. 2. Check/replace the related harness/cable, connector and parts.

Error code:	075-0003-05
Description:	ITB displacement control error
Causes:	The ITB Steering Sensor detected that the ITB was at full displacement position at the rear.
Remedy:	[Related parts] R1.00 - Harnesses connecting the Front Driver PCB (UN3/J303), the ITB Displacement Sensor PCB (UN60/J700 and J701) and the ITB Steering Sensor (PS24/J7013) - Harness between the Front Driver PCB (UN3/J303) and the ITB Displacement Control Motor (M14/J3031) - ITB Steering Sensor (PS24) - ITB Displacement Control Motor (M14) - ITB Displacement Sensor PCB (UN60) - Secondary Transfer Inner Roller - Intermediate Transfer Belt Assembly - Front Driver PCB (UN3) [Remedy] Perform the following in the order while checking whether the error is cleared. a. If the ITB is not at full displacement position, 1. Check/replace the related harness/cable, connector and parts. b. If the ITB is at full displacement position, 1. Correct displacement of the ITB. 1-1. Remove the Intermediate Transfer Belt Assembly. 1-2. Lift the left front side (where the cleaner and the ITB Motor are located) and hold the Intermediate Transfer Belt Assembly as if to twist it. 1-3. Turn the ITB Motor counterclockwise to rotate the ITB. 1-4. As the ITB is getting closer to the center, adjust the ITB position. 2. Check/replace the Secondary Transfer Inner Roller. 3. Execute COPIER> FUNCTION> MISC-P> ITB-INIT. 4. If the value displayed in COPIER> DISPLAY> MISC> ITB-POS/ITB-POS2 is out of the appropriate reference value range, execute the ITB alignment. 5. Check/replace the related harness/cable, connector and parts.

Error code:	075-0004-05
Description:	ITB displacement control error
Causes:	ITB displacement position could not be detected due to error in the Displacement Control Sensor.
Remedy:	[Related parts] R1.00 - Harness between the Front Driver PCB (UN3/J303) and the ITB Displacement Sensor PCB (UN60/J700) - ITB Displacement Sensor PCB (UN60) - Intermediate Transfer Belt Assembly - Front Driver PCB (UN3) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	075-0005-05
Description:	ITB displacement control error
Causes:	The ITB Steering Sensor detected home position error.
Remedy:	[Related parts] R1.00 - Harnesses connecting the Front Driver PCB (UN3/J303), the ITB Displacement Sensor PCB (UN60/J700 and J701) and the ITB Steering Sensor (PS24/J7013) - ITB Steering Sensor (PS24) - ITB Displacement Sensor PCB (UN60) - Intermediate Transfer Belt Assembly - Front Driver PCB (UN3) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	075-0006-05
Description:	ITB displacement control error
Causes:	The Displacement Control Sensor did not detect equilibrium position although a specified period of time had passed.
Remedy:	[Related parts] R1.00 - Harness between the Front Driver PCB (UN3/J303) and the ITB Displacement Sensor PCB (UN60/J700) - Harness between the Front Driver PCB (UN3/J303) and the ITB Displacement Control Motor (M14/J3031) - ITB Displacement Control Motor (M14) - ITB Displacement Sensor PCB (UN60) - Intermediate Transfer Belt Assembly - Front Driver PCB (UN3) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	075-0103-05
Description:	ITB displacement control error
Causes:	The ITB Steering Sensor detected that the ITB was at full displacement position at the front.
Remedy:	[Related parts] R1.00 - Harnesses connecting the Front Driver PCB (UN3/J303), the ITB Displacement Sensor PCB (UN60/J700 and J701) and the ITB Steering Sensor (PS24/J7013) - Harness between the Front Driver PCB (UN3/J303) and the ITB Displacement Control Motor (M14/J3031) - ITB Steering Sensor (PS24) - ITB Displacement Control Motor (M14) - ITB Displacement Sensor PCB (UN60) - Secondary Transfer Inner Roller - Intermediate Transfer Belt Assembly - Front Driver PCB (UN3) [Remedy] Perform the following in the order while checking whether the error is cleared. a. If the ITB is not at full displacement position, 1. Check/replace the related harness/cable, connector and parts. b. If the ITB is at full displacement position, 1. Correct displacement of the ITB. 1-1. Remove the Intermediate Transfer Belt Assembly. 1-2. Lift the left rear side (opposite side of where the cleaner and the ITB Motor are located) and hold the Intermediate Transfer Belt Assembly as if to twist it. 1-3. Turn the ITB Motor counterclockwise to rotate the ITB. 1-4. As the ITB is getting closer to the center, adjust the ITB position. 2. Check/replace the Secondary Transfer Inner Roller. 3. Execute COPIER> FUNCTION> MISC-P> ITB-INIT. 4. If the value displayed in COPIER> DISPLAY> MISC> ITB-POS/ITB-POS2 is out of the appropriate reference value range, execute the ITB alignment. 5. Check/replace the related harness/cable, connector and parts.

Error code:	100-0100-05
Description:	Laser Scanner error
Causes:	BD signal was not detected although a specified period of time had passed during operation of the Laser Scanner (Y, M).
Remedy:	[Related parts] R1.01 - Small-diameter Coaxial Cable connecting from the Riser PCB (J9) to the Laser Driver PCB (Y) and (M) (UN13/J101 and UN12/J822) - Connector between the Main Controller PCB and the Riser PCB - Harness between the DC Controller PCB (UN1/J171) and the Laser Driver PCB (Y) (UN13/J851) - Harness between the Relay PCB (UN5/J416) and the Laser Driver PCB (M) (UN12/J830) - Laser Driver PCB (Y) (UN13) - Laser Driver PCB (M) (UN12) - Main Controller PCB - Riser PCB - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	100-0102-05
Description:	Laser Scanner error
Causes:	Correction in timing of laser exposure to the Polygon Mirror (Y, M) was not completed within the specified period of time.
Remedy:	[Related parts] R1.00 - Small-diameter Coaxial Cable connecting from the Riser PCB (J9) to the Laser Driver PCB (Y) and (M) (UN13/J101 and UN12/J822) - Connector between the Main Controller PCB and the Riser PCB - Harness between the DC Controller PCB (UN1/J171) and the Laser Driver PCB (Y) (UN13/J851) - Laser Driver PCB (Y) (UN13) - Laser Driver PCB (M) (UN12) - Main Controller PCB - Riser PCB - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	100-0300-05
Description:	Laser Scanner error
Causes:	BD signal was not detected although a specified period of time had passed during operation of the Laser Scanner (C, Bk).
Remedy:	[Related parts] R1.00 - Small-diameter Coaxial Cable connecting from the Riser PCB (J9) to the Laser Driver PCB (C) and (Bk) (UN15/J802 and UN14/J822) - Connector between the Main Controller PCB and the Riser PCB - Harness between the DC Controller PCB (UN1/J171) and the Laser Driver PCB (C) (UN15/J862) - Laser Driver PCB (C) (UN15) - Laser Driver PCB (Bk) (UN14) - Main Controller PCB - Riser PCB - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	100-0302-05
Description:	Laser Scanner error
Causes:	Correction in timing of laser exposure to the Polygon Mirror (C, Bk) was not completed within the specified period of time.
Remedy:	[Related parts] R1.00 - Small-diameter Coaxial Cable connecting from the Riser PCB (J9) to the Laser Driver PCB (C) and (Bk) (UN15/J802 and UN14/J822) - Connector between the Main Controller PCB and the Riser PCB - Harness between the DC Controller PCB (UN1/J171) and the Laser Driver PCB (C) (UN15/J862) - Laser Driver PCB (C) (UN15) - Laser Driver PCB (Bk) (UN14) - Main Controller PCB - Riser PCB - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	102-0101-05
Description:	EEPROM error
Causes:	An error in check sum of EEPROM on the Laser Scanner (Y) was detected.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN2/J1200) and the Relay PCB (UN7/J1817) - Harnesses between the DC Controller PCB (UN2/J1259, J1220 and J1221) and the Laser Interface PCB (UN106/J15, J10 and J16) - Harness between the Laser Interface PCB (UN106/J70) and the Laser Scanner Unit (Y) (J8076) - Laser Scanner Unit (Y) - Laser Interface PCB (UN106) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	102-0301-05
Description:	EEPROM error
Causes:	An error in check sum of EEPROM on the Laser Scanner (C) was detected.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN2/J1200) and the Relay PCB (UN7/J1817) - Harnesses between the DC Controller PCB (UN2/J1259, J1220 and J1221) and the Laser Interface PCB (UN106/J15, J10 and J16) - Harness between the Laser Interface PCB (UN106/J76) and the Laser Scanner Unit (C) (J8066) - Laser Scanner Unit (C) - Laser Interface PCB (UN106) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	112-0000-05
Description:	Laser Shutter Error
Causes:	Home position of the Laser Shutter was not detected.
Remedy:	[Related parts] R1.00 - Harness connecting from the Feed/Drum Driver PCB (UN2/J224) to the Laser Shutter Motor and Laser Shutter Sensor (M28/J6060 and PS29/J6123) - Laser Shutter Sensor (PS29) - Laser Shutter Motor (M28) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Laser Shutter Motor is properly installed. 2. Check that there is no damage or deformation with the Laser Shutter Sensor Flag. 3. Check/replace the related harness/cable, connector and parts.

Error code:	112-0001-05
Description:	Laser Shutter Error
Causes:	Home position was not detected although the Laser Shutter was closed.
Remedy:	[Related parts] R1.00 - Harness connecting from the Feed/Drum Driver PCB (UN2/J224) to the Laser Shutter Motor and Laser Shutter Sensor (M28/J6060 and PS29/J6123) - Laser Shutter Sensor (PS29) - Laser Shutter Motor (M28) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Laser Shutter Motor is properly installed. 2. Check that there is no damage or deformation with the Laser Shutter Sensor Flag. 3. Check/replace the related harness/cable, connector and parts.

Error code:	112-0002-05
Description:	Laser Shutter Error
Causes:	Change in home position was not detected while the Laser Shutter was open.
Remedy:	[Related parts] R1.00 - Harness connecting from the Feed/Drum Driver PCB (UN2/J224) to the Laser Shutter Motor and Laser Shutter Sensor (M28/J6060 and PS29/J6123) - Laser Shutter Sensor (PS29) - Laser Shutter Motor (M28) - Feed/Drum Driver PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Laser Shutter Motor is properly installed. 2. Check that there is no damage or deformation with the Laser Shutter Sensor Flag. 3. Check/replace the related harness/cable, connector and parts.

Error code:	197-0000-05
Description:	Serial communication error
Causes:	A communication error between the DC Controller PCB and the Laser Scanner (Y, M) was detected.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J171) and the Laser Driver PCB (Y) (UN13/J851) - Small-diameter Coaxial Cable connecting from the Riser PCB (J9) to the Laser Driver PCB (Y) and (M) (UN13/J802 and UN12/J822) - Laser Driver PCB (Y) (UN13) - Laser Driver PCB (M) (UN12) - Riser PCB - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	197-0100-05
Description:	Serial communication error
Causes:	A communication error between the DC Controller PCB and the Laser Scanner (C, Bk) was detected.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J171) and the Laser Driver PCB (C) (UN15/J862) - Small-diameter Coaxial Cable connecting from the Riser PCB (J9) to the Laser Driver PCB (C) and (Bk) (UN15/J802 and UN14/J822) - Laser Driver PCB (C) (UN15) - Laser Driver PCB (Bk) (UN14) - Riser PCB - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	197-2000-05
Description:	Serial communication error
Causes:	A communication error of ASIC (HV_KONA) in the DC Controller PCB was detected.
Remedy:	Replace the DC Controller PCB (UN1). [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	197-2001-05
Description:	Serial communication error
Causes:	A communication error between the DC Controller PCB and the Side Paper Deck was detected.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J170) and the Side Paper Deck Controller PCB (J357) - DC Controller PCB (UN1) - Side Paper Deck Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	197-2002-05
Description:	Serial communication error
Causes:	A communication error between the DC Controller PCB and the Front Driver PCB was detected.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J111) and the Front Driver PCB (UN3/J301) - Front Driver PCB (UN3) - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	197-2003-05
Description:	Serial communication error
Causes:	A communication error between the DC Controller PCB and the Main Controller PCB was detected.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J100 and J101) and the Riser PCB (J2 and J10) - Connector between the Main Controller PCB and the Riser PCB - Riser PCB - Main Controller PCB - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	197-2004-05
Description:	Serial communication error
Causes:	A communication error between the DC Controller PCB and the Feed/Drum Driver PCB was detected.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J170 and J172) and the Feed/Drum Driver PCB (UN2/J202 and J203) - Feed/Drum Driver PCB (UN2) - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	197-2005-05
Description:	Serial communication error
Causes:	A communication error between the DC Controller PCB and the Feed/Drum Driver PCB was detected.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J170 and J172) and the Feed/Drum Driver PCB (UN2/J202 and J203) - Feed/Drum Driver PCB (UN2) - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	199-0101-05
Description:	Error in high voltage sequence (Y)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0102-05
Description:	Error in high voltage sequence (M)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0103-05
Description:	Error in high voltage sequence (C)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0104-05
Description:	Error in high voltage sequence (K)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0201-05
Description:	Error in high voltage sequence (Y)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0202-05
Description:	Error in high voltage sequence (M)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0203-05
Description:	Error in high voltage sequence (C)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0204-05
Description:	Error in high voltage sequence (K)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0301-05
Description:	Error in high voltage sequence (Y)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0302-05
Description:	Error in high voltage sequence (M)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0303-05
Description:	Error in high voltage sequence (C)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	199-0304-05
Description:	Error in high voltage sequence (K)
Causes:	Error for collecting log.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.

Error code:	202-0001-04
Description:	Reader Scanner Unit HP error
Causes:	The Reader Scanner Unit could not detect the home position when starting scanning operation.
Remedy:	[Related parts] - Harness between the Scanner Unit HP Sensor (SR2/J5202) and the Reader Controller PCB (UN1/J102) (Unit of replacement: DF MOUNT ASSEMBLY, L) - Harness between the Scanner Motor (M1/J601) and the Reader Controller PCB (PCB1/J108) (Unit of replacement: CABLE, MOTOR) - Scanner Unit HP Sensor (SR2) - Scanner Motor (M1) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	202-0002-04
Description:	Reader Scanner Unit HP error
Causes:	The Reader Scanner Unit could not detect the home position when completing scanning operation.
Remedy:	[Related parts] - Harness between the Scanner Unit HP Sensor (SR2/J5202) and the Reader Controller PCB (UN1/J102) (Unit of replacement: DF MOUNT ASSEMBLY, L) - Harness between the Scanner Motor (M1/J601) and the Reader Controller PCB (PCB1/J108) (Unit of replacement: CABLE, MOTOR) - Scanner Unit HP Sensor (SR2) - Scanner Motor (M1) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	202-0003-04
Description:	Reader Scanner Unit HP error
Causes:	An error in the Reader Scanner Unit position was detected when reading of a job was started.
Remedy:	[Related parts] - Harness between the Scanner Unit HP Sensor (SR2/J5202) and the Reader Controller PCB (UN1/J102) (Unit of replacement: DF MOUNT ASSEMBLY, L) - Harness between the Scanner Motor (M1/J601) and the Reader Controller PCB (PCB1/J108) (Unit of replacement: CABLE, MOTOR) - Scanner Unit HP Sensor (SR2) - Scanner Motor (M1) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	202-0004-04
Description:	Reader Scanner Unit HP error
Causes:	Home position error of the Reader Scanner Unit was detected when reading of a job was completed.
Remedy:	[Related parts] R1.00 - Harness between the Reader Controller PCB (UN_BO2/J102) and the Scanner Unit HP Sensor (PS_A1/J5002) - Harness between the Reader Controller PCB (UN_BO2/J108) and the Scanner Motor (STM1/ J5015) - Scanner Unit HP Sensor (PS_A1) - Scanner Motor (STM1) - Reader Controller PCB (UN_BO2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	202-0101-04
Description:	DADF Scanner Unit HP error
Causes:	The DADF Scanner Unit could not detect the home position when starting scanning operation.
Remedy:	[Related parts] - Harnesses from the Glass HP Sensor to the DADF Driver PCB 1. Glass HP Sensor (SR18/J630) to Relay Connector (6P) (Unit of replacement: CABLE, READ 2 SENSOR) 2. Relay Connector (6P) to Relay Connector (9P) (Unit of replacement: PAPER DELIVERY ASSEMBLY) 3. Relay Connector (9P) to Relay Connector (9P) 4. Relay Connector (9P) to DADF Driver PCB (UN03/J413) (Unit of replacement: CABLE, MAIN SENSOR) - Harnesses from the Glass Shift Motor to the DADF Driver PCB 1. Glass Shift Motor (M8/J1225) to Relay Connector (9P) (Unit of replacement: CABLE, FRONT MOTOR) 2. Relay Connector (9P) to Relay Connector (9P) 3. Relay Connector (9P) to DADF Driver PCB (UN03/J415) (Unit of replacement: CABLE, MOTOR) - Glass HP Sensor (SR18) - Glass Shift Motor (M8) - DADF Driver PCB (UN03) (Unit of replacement: DF DRIVER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	202-0102-04
Description:	DADF Scanner Unit HP error
Causes:	The DADF Scanner Unit could not detect the home position when completing scanning operation.
Remedy:	[Related parts] - Harnesses from the Glass HP Sensor to the DADF Driver PCB 1. Glass HP Sensor (SR18/J630) to Relay Connector (6P) (Unit of replacement: CABLE, READ 2 SENSOR) 2. Relay Connector (6P) to Relay Connector (9P) (Unit of replacement: PAPER DELIVERY ASSEMBLY) 3. Relay Connector (9P) to Relay Connector (9P) 4. Relay Connector (9P) to DADF Driver PCB (UN03/J413) (Unit of replacement: CABLE, MAIN SENSOR) - Harnesses from the Glass Shift Motor to the DADF Driver PCB 1. Glass Shift Motor (M8/J1225) to Relay Connector (9P) (Unit of replacement: CABLE, FRONT MOTOR) 2. Relay Connector (9P) to Relay Connector (9P) 3. Relay Connector (9P) to DADF Driver PCB (UN03/J415) (Unit of replacement: CABLE, MOTOR) - Glass HP Sensor (SR18) - Glass Shift Motor (M8) - DADF Driver PCB (UN03) (Unit of replacement: DF DRIVER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	227-0001-04
Description:	Power supply error
Causes:	The Reader Controller PCB did not detect 24 V when the main power was turned ON.
Remedy:	[Related parts] - Harness between the Reader Controller PCB (UN1/J111) and the DADF Driver PCB (UN03/J402) (Unit of replacement: ADF POWER CABLE) - Harnesses from the Reader Controller PCB to the Relay PCB 1. Reader Controller PCB (UN1/J101) to Relay Connector (6P) (Unit of replacement: CABLE, READER POWER SUPPLY) 2. Relay Connector (6P) to Relay PCB (UN86/J505) (Unit of replacement: CABLE, SIGNAL ) - Harness between the Relay PCB (UN86/J512) and the DC Power Supply PCB (24V) (J202A) (Unit of replacement: CABLE, DC 24V, A) - Harness between the Relay PCB (UN86/J513) and the DC Power Supply PCB (24V) (J202B) (Unit of replacement: CABLE, DC 24V, B) - Harness between the DC Power Supply PCB (24V) (J102A/J102B) and the AC Driver PCB (UN20/J606) (Unit of replacement: CABLE, AC MAIN) - Harness between the Relay PCB (UN86/J518 and J514) and the DC Controller PCB (UN01/J401 and J451) (Unit of replacement: CABLE, SIGNAL) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) - DADF Driver PCB (UN03) (Unit of replacement: DF DRIVER PCB ASSEMBLY) - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Power Supply PCB (24V) (Unit of replacement: 24V POWER SUPPLY ASS`Y, LEFT) - DC Power Supply PCB (24V) (Unit of replacement: 24V POWER SUPPLY ASS`Y, RIGHT) - AC Driver PCB (UN20) (Unit of replacement: AC DRIVER PCB ASS`Y) - DC Controller PCB (UN2) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When an error is detected, conduction of 24 V is stopped. At power check, check if 24 V is conducted or rated voltage is output by repeating power cycling of the machine. - Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	227-0101-04
Description:	Power supply error
Causes:	The DADF Driver PCB did not detect 24 V when the main power was turned ON.
Remedy:	[Related parts] - Harness between the Reader Controller PCB (UN1/J111) and the DADF Driver PCB (UN03/J402) (Unit of replacement: ADF POWER CABLE) - Harnesses from the Reader Controller PCB to the Relay PCB 1. Reader Controller PCB (UN1/J101) to Relay Connector (6P) (Unit of replacement: CABLE, READER POWER SUPPLY) 2. Relay Connector (6P) to Relay PCB (UN86/J505) (Unit of replacement: CABLE, SIGNAL ) - Harness between the Relay PCB (UN86/J512) and the DC Power Supply PCB (24V) (J202A) (Unit of replacement: CABLE, DC 24V, A) - Harness between the Relay PCB (UN86/J513) and the DC Power Supply PCB (24V) (J202B) (Unit of replacement: CABLE, DC 24V, B) - Harness between the DC Power Supply PCB (24V) (J102A/J102B) and the AC Driver PCB (UN20/J606) (Unit of replacement: CABLE, AC MAIN) - Harness between the Relay PCB (UN86/J518 and J514) and the DC Controller PCB (UN01/J401 and J451) (Unit of replacement: CABLE, SIGNAL) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) - DADF Driver PCB (UN03) (Unit of replacement: DF DRIVER PCB ASSEMBLY) - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Power Supply PCB (24V) (Unit of replacement: 24V POWER SUPPLY ASS`Y, LEFT) - DC Power Supply PCB (24V) (Unit of replacement: 24V POWER SUPPLY ASS`Y, RIGHT) - AC Driver PCB (UN20) (Unit of replacement: AC DRIVER PCB ASS`Y) - DC Controller PCB (UN2) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When an error is detected, conduction of 24 V is stopped. At power check, check if 24 V is conducted or rated voltage is output by repeating power cycling of the machine. - Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	240-0002-05
Description:	Controller communication error
Causes:	Image output request waiting status was detected.
Remedy:	[Related parts] - Harness between the Main Controller PCB 2 (PWB02/J5201) and the DC Controller PCB (UN01/ J443) (Unit of replacement: CABLE, COMMUNICATION) - Harness between the Main Controller PCB 2 (PWB02/J5202) and the DC Controller PCB (UN01/ J442) (Unit of replacement: CABLE, SIGNAL) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) - Main Controller PCB 2 (PWB02) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 2) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	246
Description:	Duplex Unit Flash Memory Failure Applicable Status Code: Code 246: Hardware failure with Duplex Unit Flash Memory.
Causes:	• Duplex Unit • Motor Driver Board, PL2.1.10
Remedy:	1 Check the Duplex Unit connector for damage. Is the connector damaged? Replace the connector. Replace the Duplex Unit. If the error persists, go to Step 2. 2 Check all pins on the DUPLEX Harness for continuity. Disconnect the DUPLEX Harness. Is the DUPLEX Harness conductive? Replace the Motor Driver Board. If the error persists, go to Step 3. Replace the DUPLEX Harness. 3 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness.

Error code:	247
Display:	Service Call 247:Error
Description:	Motor Driver Board Flash Memory Failure Applicable Status Code: Code 247: Hardware failure with the Motor Driver Board Flash Memory.
Causes:	• Motor Driver Board, PL2.1.10
Remedy:	1 Check the connections to the Engine Control Board. Are DV0 and DV1 completely connected? Replace the Motor Driver Board. Connect the two ribbon cables.

Error code:	248-0001-04
Description:	EEPROM error
Causes:	Reading error was detected when the Main Controller PCB 1 read the Reader backup value in the Reader Controller PCB.
Remedy:	Check/replace the Reader Controller PCB (UN1). (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	248-0002-04
Description:	EEPROM error
Causes:	The Main Controller PCB 1 failed writing of the Reader backup value in the Reader Controller PCB.
Remedy:	Check/replace the Reader Controller PCB (UN1). (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	248-0003-04
Description:	EEPROM error
Causes:	The Main Controller PCB 1 detected an error at inspection after completion of writing of the Reader backup value in the Reader Controller PCB.
Remedy:	Check/replace the Reader Controller PCB (UN1). (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	260-0001-05
Description:	Power supply error
Causes:	An error in 3.3 VA power supply was detected at startup.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J171) and the Environment Sensor (UN50/J810) - Harness between the DC Controller PCB (UN1/J120) and the Primary Transfer/Bk Developing Charging High-Voltage PCB (UN17/J622) - Harness between the DC Controller PCB (UN1/J122) and the Secondary Transfer High-Voltage PCB (UN18/J657) - Harness between the DC Controller PCB (UN1/J123) and the Charging High-Voltage PCB (YMC) (UN77/J641) - Harness between the DC Controller PCB (UN1/J124) and the Developing High-Voltage PCB (YMC) (UN76/J611) - DC Controller PC (UN1) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	260-0002-05
Description:	Power supply error
Causes:	An error in 5 V power supply was detected at startup of CPU.
Remedy:	[Related parts] 1.00 - Sensor harness for 5 V power supply - Harness between the Feed/Drum Driver PCB (UN2/J214) and the Drawer Unit (J5012) - Harness between the Feed/Drum Driver PCB (UN2/J216) and the Second/Third Delivery Unit (J5032) - Harness between the Feed/Drum Driver PCB (UN2/J219) and the Right Door Relay PCB (UN61/ J1100) - Harness between the DC Controller PCB (UN1/J111) and the Front Driver PCB (UN3/J301) - Harness between the DC Controller PCB (UN1/J170) and the Feed/Drum Driver PCB (UN2/J202) - Harness between the DC Controller PCB (UN1/J110) and the Finisher (J1103) - Harness between the DC Controller PCB (UN1/J101) and the Riser PCB (J10) - Feed/Drum Driver PCB (UN2) - Right Door Relay PCB (UN61) - Front Driver PCB (UN3) - Riser PCB - DC Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	280-0001-04
Description:	Communication error
Causes:	Communication between the Reader Controller PCB and the Reader Scanner Unit was not completed within the specified period of time.
Remedy:	[Related parts] - Harness between the Reader Scanner Unit (UN2/J1101) and the Reader Controller PCB (UN1/ J106) (Unit of replacement: FLEXIBLE FLAT CABLE UNIT) - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) - Reader Scanner Unit (UN2) (Unit of replacement: SCANNER UNIT, READER) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	280-0002-04
Description:	Communication error
Causes:	Disconnection of FFC between the Reader Controller PCB and the Reader Scanner Unit was detected.
Remedy:	[Related parts] - Harness between the Reader Scanner Unit (UN2/J1101) and the Reader Controller PCB (UN1/ J106) (Unit of replacement: FLEXIBLE FLAT CABLE UNIT) - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	280-0101-04
Description:	Communication error
Causes:	Communication between the Reader Controller PCB and the DADF Scanner Unit was not completed within the specified period of time.
Remedy:	[Related parts] - Harness between the DADF Scanner Unit (J1102) and the Reader Controller PCB (UN1/J105) (Unit of replacement: FLEXIBLE FLAT CABLE UNIT) - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) - DADF Scanner Unit (Unit of replacement: SCANNER UNIT, ADF) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	280-0102-04
Description:	Communication error
Causes:	Disconnection of FFC between the Reader Controller PCB and the DADF Scanner Unit was detected.
Remedy:	[Related parts] - Harness between the DADF Scanner Unit (J1102) and the Reader Controller PCB (UN1/J105) (Unit of replacement: FLEXIBLE FLAT CABLE UNIT) - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	302-0001-04
Description:	Error in paper front white shading
Causes:	An access error to the paper front white shading RAM or a paper front white shading value that was higher than the specified value was detected.
Remedy:	[Related parts] - Harness between the Reader Scanner Unit (UN2/J1101) and the Reader Controller PCB (UN1/ J106) (Unit of replacement: FLEXIBLE FLAT CABLE UNIT) - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) - Reader Scanner Unit (UN2) (Unit of replacement: SCANNER UNIT, READER) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	302-0002-04
Description:	Error in paper front black shading
Causes:	An access error to the paper front black shading RAM or a paper front black shading value that was higher than the specified value was detected.
Remedy:	[Related parts] - Harness between the Reader Scanner Unit (UN2/J1101) and the Reader Controller PCB (UN1/ J106) (Unit of replacement: FLEXIBLE FLAT CABLE UNIT) - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) - Reader Scanner Unit (UN2) (Unit of replacement: SCANNER UNIT, READER) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	302-0101-04
Description:	Error in paper back white shading
Causes:	An access error to the paper back white shading RAM or a paper back white shading value that was higher than the specified value was detected.
Remedy:	[Related parts] - Harness between the DADF Scanner Unit (J1102) and the Reader Controller PCB (UN1/J105) (Unit of replacement: FLEXIBLE FLAT CABLE UNIT) - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) - DADF Scanner Unit (Unit of replacement: SCANNER UNIT, ADF) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	302-0102-04
Description:	Error in paper back black shading
Causes:	An access error to the paper back black shading RAM or a paper back black shading value that was higher than the specified value was detected.
Remedy:	[Related parts] - Harness between the DADF Scanner Unit (J1102) and the Reader Controller PCB (UN1/J105) (Unit of replacement: FLEXIBLE FLAT CABLE UNIT) - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) - DADF Scanner Unit (Unit of replacement: SCANNER UNIT, ADF) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	350
Description:	ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0
Causes:	• ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty

Error code:	351
Description:	ID sensor error 2 The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern
Causes:	• ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty

Error code:	354
Display:	Set new fuser 354: Fuser life
Description:	Fuser life (occurs when fuser life continuation is OFF).
Causes:	Right after replacing fuser?
Remedy:	Check fuser life. Replace fuser.

Error code:	355
Display:	Set new belt 355: Belt life
Description:	Belt life notified (alarm). Print N-count by opening and closing cover.
Causes:	Right after replacing belt?
Remedy:	Check belt life. Replace belt.

Error code:	400-0001-04
Description:	Communication error
Causes:	A communication error between the Reader Controller PCB and the DADF Driver PCB was detected.
Remedy:	[Related parts] R1.00 - Harness between the Reader Controller PCB (UN_BO1/J4) and the DADF Driver PCB (PCB1/ J401) - Harness between the Reader Controller PCB (UN_BO1/J104) and the DADF Driver PCB (PCB1/ J402) - DADF Driver PCB (PCB1) - Reader Controller PCB (UN_BO1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	400-0002-04
Description:	Communication error
Causes:	A communication error between the Reader Controller PCB and the DADF Driver PCB was detected.
Remedy:	[Related parts] - Harness between the DADF Driver PCB (UN03/J401) and the Reader Controller PCB (UN1/J104) (Unit of replacement: CABLE, FLAT) - Harness between the DADF Driver PCB (UN03/J402) and the Reader Controller PCB (UN1/J111) (Unit of replacement: CABLE, ADF POWER SUPPLY) - DADF Driver PCB (UN3) (Unit of replacement: DF DRIVER PCB ASSEMBLY) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	400-0003-04
Description:	Communication error
Causes:	Disconnection of the harness between the Reader Controller PCB and the DADF Driver PCB was detected.
Remedy:	[Related parts] - Harness between the DADF Driver PCB (UN03/J401) and the Reader Controller PCB (UN1/J104) (Unit of replacement: CABLE, FLAT) - Harness between the DADF Driver PCB (UN03/J402) and the Reader Controller PCB (UN1/J111) (Unit of replacement: CABLE, ADF POWER SUPPLY) - DADF Driver PCB (UN3) (Unit of replacement: DF DRIVER PCB ASSEMBLY) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	412-0005-04
Description:	Fan error
Causes:	Rotation of fan was detected after the stop signal for the DADF Cooling Fan 1/2 was transmitted.
Remedy:	[Related parts] - Harness between DADF Cooling Fan 2 (FM2/J620) and the DADF Driver PCB (UN03/J408) (Unit of replacement: CABLE, REAR MOTOR, 2) - DADF Cooling Fan 1 (FM1) - DADF Cooling Fan 2 (FM2) - DADF Driver PCB (UN03) (Unit of replacement: DF DRIVER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	412-0006-04
Description:	Fan error
Causes:	Stop of fan was detected after rotation signal for the DADF Cooling Fan 1/2 was transmitted.
Remedy:	[Related parts] - Harness between DADF Cooling Fan 2 (FM2/J620) and the DADF Driver PCB (UN03/J408) (Unit of replacement: CABLE, REAR MOTOR, 2) - DADF Cooling Fan 1 (FM1) - DADF Cooling Fan 2 (FM2) - DADF Driver PCB (UN03) (Unit of replacement: DF DRIVER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	423-0001-04
Description:	SDRAM error in the Reader Controller PCB
Causes:	Either an access error to SDRAM in the Reader Controller PCB or an error at data inspection was detected.
Remedy:	[Remedy] Replace the Reader Controller PCB (PCB1). (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	490-0001-04
Description:	Different Scanner Unit model error
Causes:	A wrong Scanner Unit was installed.
Remedy:	Install the Scanner Unit for this model.

Error code:	490-0101-04
Description:	Different DADF model error
Causes:	A wrong DADF was installed.
Remedy:	[Related parts] R1.00 - Flat Cable between the DADF Driver PCB (PCB1/J401) and the Reader Controller PCB (UN_ BO1/J4) - DADF Driver PCB (PCB1) - Reader Controller PCB (UN_BO1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check if the installed DADF model matches the model that was set in "COPIER> OPTION> CUSTOM> SCANTYPE". If not matched, install the appropriate DADF. 2. Check/replace the related parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	501-0000-02
Description:	Communication error (Finisher-H1)
Causes:	A communication error between the host machine and the Finisher was detected.
Remedy:	[Related parts] - Harnesses and connectors from the DC Controller PCB to the Finisher Controller PCB - Finisher Controller PCB (PCB1) - DC Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness and connector between the DC Controller PCB and the Finisher Controller PCB. 2. Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. 3. Replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	503-0021-02
Description:	a. Error in communication between the Finisher - Insertion Unit (Finisher-X1) b. Error in communication between the Finisher and Saddle Unit (Finisher-V)
Causes:	a. Communication failed between Finisher - Insertion Unit b. Communication error between the Finisher Controller PCB and the Saddle Stitcher Controller PCB was detected. (Command transmission error)
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Finisher Controller PCB to the Insertion Unit Controller PCB - Finisher Controller PCB (PBA101) - Insertion Unit Controller PCB(PCB3) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. - When replacing the Insertion Unit Controller PCB, refer to "Adjustment> Adjustment at Time of Parts Replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses and connectors from the Finisher Controller PCB to the Saddle Stitcher Controller PCB - Finisher Controller PCB (PCB101) - Saddle Stitcher Controller PCB (PCB201) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness and connector between the Finisher Controller PCB and the Saddle Stitcher Controller PCB. 2. Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. 3. Replace the Saddle Stitcher Controller PCB.

Error code:	503-0022-02
Description:	a. Error in communication between the Finisher - Insertion Unit (Finisher-X1/Document Insertion Unit-N1) b. Error in communication between the Finisher and Saddle Unit (Finisher-V)
Causes:	a. Communication failed between Finisher - Insertion Unit b. Communication error between the Finisher Controller PCB and the Saddle Stitcher Controller PCB was detected. (Command reception error)
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Finisher Controller PCB to the Insertion Unit Controller PCB - Insertion Unit Controller PCB(PCB3) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. - When replacing the Insertion Unit Controller PCB, refer to "Adjustment> Adjustment at Time of Parts Replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses and connectors from the Finisher Controller PCB to the Saddle Stitcher Controller PCB - Finisher Controller PCB (PCB101) - Saddle Stitcher Controller PCB (PCB201) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness and connector between the Finisher Controller PCB and the Saddle Stitcher Controller PCB. 2. Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. 3. Replace the Saddle Stitcher Controller PCB.

Error code:	503-0031-02
Description:	Error in communication between the Finisher and Puncher Unit (Finisher-V)
Causes:	Communication error between the Finisher Controller PCB and the Puncher Controller PCB was detected. (Command transmission error)
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses and connectors from the Finisher Controller PCB to the Puncher Controller PCB - Finisher Controller PCB (PCB101) - Puncher Controller PCB (PCB301) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness and connector between the Finisher Controller PCB and the Puncher Controller PCB. 2. Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. 3. Replace the Puncher Controller PCB. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	503-0032-02
Description:	Error in communication between the Finisher and Puncher Unit (Finisher-V)
Causes:	Communication error between the Finisher Controller PCB and the Puncher Controller PCB was detected. (Command reception error)
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses and connectors from the Finisher Controller PCB to the Puncher Controller PCB - Finisher Controller PCB (PCB101) - Puncher Controller PCB (PCB301) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness and connector between the Finisher Controller PCB and the Puncher Controller PCB. 2. Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. 3. Replace the Puncher Controller PCB. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	503-0041-02
Description:	Communication error between Finisher and Multi Function Professional Puncher (M.F PRO PUNCHER-A1/FIN-W1/SADDLE FIN-W1/FINISHER-X1)
Causes:	An error was detected in communication from the finisher to the Multi Function Professional Puncher.
Remedy:	[Related parts] - Harness between the BOARD, OPCON PCB and the Finisher Controller PCB - BOARD, OPCON PCB - Finisher Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	503-0042-02
Description:	Communication error between Finisher and Multi Function Professional Puncher (M.F PRO PUNCHER-A1/FIN-W1/SADDLE FIN-W1/FINISHER-X1)
Causes:	An error was detected in communication from the Multi Function Professional Puncher to the finisher.
Remedy:	[Related parts] - Harness between the BOARD, OPCON PCB and the Finisher Controller PCB - BOARD, OPCON PCB - Finisher Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	503-0061-02
Description:	a. Error in communication between the Finisher - Paper Folding Unit (Finisher-X1) b. Error in communication between the IC of Finisher Controller PCB (Finisher-V)
Causes:	a. Communication failed between the Finisher - Paper Folding Unit b. Communication error between the IC of Finisher Controller PCB was detected. (Command transmission error)
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Finisher Controller PCB to the Paper Folding Unit Controller PCB - Finisher Controller PCB (PBA101) - Paper Folding Unit Controller PCB (PCB1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. - When replacing the Paper Folding Unit Controller PCB, refer to "Adjustment> Adjustment at Time of Parts Replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Finisher Controller PCB (PCB101) [Remedy] Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	503-0062-02
Description:	a. Error in communication between the Finisher - Paper Folding Unit (Paper Folding Unit- J1/Finisher-X1) b. Error in communication between the IC of Finisher Controller PCB (Finisher-V)
Causes:	a. Communication failed between the Finisher - Paper Folding Unit b. Communication error between the IC of Finisher Controller PCB was detected. (Command reception error)
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Finisher Controller PCB to the Paper Folding Unit Controller PCB - Finisher Controller PCB (PBA101) - Paper Folding Unit Controller PCB (PCB1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. - When replacing the Paper Folding Unit Controller PCB, refer to "Adjustment> Adjustment at Time of Parts Replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Finisher Controller PCB (PCB101) [Remedy] Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	505-0001-02
Description:	a. Finisher back-up RAM (EEPROM) error (Finisher-X1) b. Finisher data error (Finisher-V) c. Backup data error (failed data reading) (Document Insertion Unit-N1; Location Inf. 71)
Causes:	a. The checksum for the EEPROM data has an error. (The value written in EEPROM and the value extracted from EEPROM doesn`t conform.) b. The data read from Finisher Controller PCB has an error. (The read data doesn`t match with the written data.) c. Data failed to be read properly
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Finisher Controller PCB (PBA101) [Remedy] Check/replace the Finisher Controller PCB (PBA101). [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Finisher Controller PCB (PCB101) [Remedy] Replace the Finisher Controller PCB (PCB101). [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. INSERTION UNIT-N1 [Related parts] - Insertion Unit Controller PCB (PCB3) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Insertion Unit Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

Error code:	505-0004-02
Description:	a. Back-up RAM error (Multi Function Professional Puncher-A1) b. Puncher unit data error (Finisher-V)
Causes:	a. The checksum for the EEPROM data has an error. (The value written in EEPROM and the value extracted from EEPROM doesn`t conform.) b. The data read from Puncher Controller PCB has an error. (The read data doesn`t match with the written data.)
Remedy:	a. MULTI FUNCTION PROFESSIONAL PUNCHER-A1 [Related parts] - Multi Function Professional Puncher Controller PCB [Remedy] Check/replace Multi Function Professional Puncher Controller PCB. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Puncher Controller PCB (PCB301) [Remedy] Replace the Puncher Controller PCB. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	505-0005-02
Description:	Error in the Paper Folding Unit backup RAM (Paper Folding Unit-J1)
Causes:	Read-write on EPROM is failed to detect.
Remedy:	[Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Paper Folding Unit Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

Error code:	514-0002-02
Description:	Assist Motor error (Finisher-H1)
Causes:	- The Assist HP Sensor was not turned ON although 3 seconds had passed after the Assist Motor operation started. - The Assist HP Sensor was not turned ON when starting operation.
Remedy:	[Related parts] - Harnesses and connectors from the Finisher Controller PCB to the Assist HP Sensor - Harnesses and connectors from the Finisher Controller PCB to the Assist Motor - Assist HP Sensor (PS7) - Assist Motor (M5) - Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual.

Error code:	514-8001-02
Description:	a. Processing Tray HP error (Finisher-W1) b. Error in the Gripper Base Motor (Finisher-X1) c. Error in the Paper End Assist Motor (Finisher-V)
Causes:	a. The Processing Tray HP Sensor was not turned ON although 5 sec had passed after the Assist Motor operation started. b. The gripper does not come off the Gripper Base Rear Sensor when the Gripper Base Motor has been driven for 3 seconds. c. The assist belt does not come off the Paper End Assist HP Sensor when the Paper End Assist Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Processing Tray HP Sensor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (16P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (16P) to Processing Tray HP Sensor (PS13) (Unit of replacement: CABLE, BJOG) - Harnesses from the Finisher Controller PCB to the Assist Motor 1. Finisher Controller PCB (UN3/J111) to Relay Connector (12P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (J12P) to Assist Motor (M12/J632) (Unit of replacement: CABLE, JOG-U) - Processing Tray HP Sensor (PS13) - Assist Motor (M12) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Gripper Base Rear Sensor (S117) to the Finisher Controller PCB - Harnesses from the Gripper Base Motor (M116) to the Finisher Controller PCB - Gripper Base Rear Sensor (S117) - Gripper Base Motor (M116) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Gripper Base Rear Sensor (S117) to the Finisher Controller PCB - Harnesses from the Gripper Base Motor (M116) to the Finisher Controller PCB - Gripper Base Rear Sensor (S117) - Gripper Base Motor (M116) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Paper End Assist HP Sensor (PS123) to the Finisher Controller PCB - Harnesses from the Paper End Assist Motor (M113) to the Finisher Controller PCB - Paper End Assist HP Sensor (PS123) - Paper End Assist Motor (M113) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	514-8002-02
Description:	a. Processing Tray HP error (Finisher-W1) b. Error in the Gripper Base Motor (Finisher-X1) c. Error in the Paper End Assist Motor (Finisher-V)
Causes:	a. The Processing Tray HP Sensor was not turned OFF although 5 sec had passed after the Assist Motor operation started. b. The Gripper Base Rear Sensor dose not detect the gripper when the Gripper Base Motor has been driven for 3 seconds. c. The Paper End Assist HP Sensor does not detect the assist belt when the Paper End Assist Motor has been driven for 2 seconds.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Processing Tray HP Sensor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (16P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (16P) to Processing Tray HP Sensor (PS13) (Unit of replacement: CABLE, BJOG) - Harnesses from the Finisher Controller PCB to the Assist Motor 1. Finisher Controller PCB (UN3/J111) to Relay Connector (12P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (J12P) to Assist Motor (M12/J632) (Unit of replacement: CABLE, JOG-U) - Processing Tray HP Sensor (PS13) - Assist Motor (M12) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Gripper Base Rear Sensor (S117) to the Finisher Controller PCB - Harnesses from the Gripper Base Motor (M116) to the Finisher Controller PCB - Gripper Base Rear Sensor (S117) - Gripper Base Motor (M116) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Front Alignment HP Sensor (PS115) to the Finisher Controller PCB - Harnesses from the Front Alignment Motor (M107) to the Finisher Controller PCB - Front Alignment HP Sensor (PS115) - Front Alignment Motor (M107) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	516-0001-02
Description:	Paddle Motor error (Finisher-H1)
Causes:	- The Paper Fold HP Sensor was not turned OFF although 3 seconds had passed after the Paddle Motor operation started. - The last paper fold operation is not finished when driving the Paddle Motor.
Remedy:	[Related parts] - Harnesses and connectors from the Finisher Controller PCB to the Paper Fold HP Sensor - Harnesses and connectors from the Finisher Controller PCB to the Paddle Motor - Paper Fold HP Sensor (PS8) - Paddle Motor (M10) - Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual.

Error code:	516-0002-02
Description:	Paddle Motor error (Finisher-H1)
Causes:	- The Paper Fold HP Sensor was not turned ON although 3 seconds had passed after the Paddle Motor operation started. - The last paper fold operation is not finished when driving the Paddle Motor.
Remedy:	[Related parts] - Harnesses and connectors from the Finisher Controller PCB to the Paper Fold HP Sensor - Harnesses and connectors from the Finisher Controller PCB to the Paddle Motor - Paper Fold HP Sensor (PS8) - Paddle Motor (M10) - Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual.

Error code:	530-8001-02
Description:	a. Rear Alignment Guide HP error (Finisher-W1) b. Error in the Front Alignment Motor (Finisher-X1) c. Error in the Front Alignment Motor (Finisher-V)
Causes:	a. The Rear Alignment Guide HP Sensor was not turned ON although 5 sec had passed after the Rear Alignment Motor operation started. b. The front alignment plate does not come off the Front Alignment HP Sensor when the Front Alignment Motor has been driven for 4 seconds. c. The front alignment plate does not come off the Front Alignment HP Sensor when the Front Alignment Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Rear Alignment Guide HP Sensor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (16P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (16P) to Rear Alignment Guide HP Sensor (PS12/J608) (Unit of replacement: CABLE, BJOG) - Harnesses from the Finisher Controller PCB to the Rear Alignment Motor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (16P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (16P) to Rear Alignment Motor (M10/J612) (Unit of replacement: CABLE, BJOG) - Rear Alignment Guide HP Sensor (PS12) - Rear Alignment Motor (M10) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Front Alignment HP Sensor (S108) to the Finisher Controller PCB - Harnesses from the Front Alignment Motor (M108) to the Finisher Controller PCB - Front Alignment HP Sensor (S108) - Front Alignment Motor (M108) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Front Alignment HP Sensor (PS115) to the Finisher Controller PCB - Harnesses from the Front Alignment Motor (M107) to the Finisher Controller PCB - Front Alignment HP Sensor (PS115) - Front Alignment Motor (M107) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	530-8002-02
Description:	a. Rear Alignment Guide HP error (Finisher-W1) b. Error in the Front Alignment Motor (Finisher-X1) c. Error in the Front Alignment Motor (Finisher-V)
Causes:	a. The Rear Alignment Guide HP Sensor was not turned OFF although 5 sec had passed after the Rear Alignment Motor operation started. b. The Front Alignment HP Sensor does not detect the Front Alignment plate when the Front Alignment Motor has been driven for 4 seconds. c. The Front Alignment HP Sensor does not detect the Front Alignment plate when the Front Alignment Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Rear Alignment Guide HP Sensor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (16P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (16P) to Rear Alignment Guide HP Sensor (PS12/J608) (Unit of replacement: CABLE, BJOG) - Harnesses from the Finisher Controller PCB to the Rear Alignment Motor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (16P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (16P) to Rear Alignment Motor (M10/J612) (Unit of replacement: CABLE, BJOG) - Rear Alignment Guide HP Sensor (PS12) - Rear Alignment Motor (M10) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Front Alignment HP Sensor (S108) to the Finisher Controller PCB - Harnesses from the Front Alignment Motor (M108) to the Finisher Controller PCB - Front Alignment HP Sensor (S108) - Front Alignment Motor (M108) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Front Alignment HP Sensor (PS115) to the Finisher Controller PCB - Harnesses from the Front Alignment Motor (M107) to the Finisher Controller PCB - Front Alignment HP Sensor (PS115) - Front Alignment Motor (M107) - Finisher Controller PCB (PCB1) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	531-8001-02
Description:	a. Staple HP error (Finisher-W1) b. Error in the Staple Motor (Finisher-X1) c. Error in the Staple Motor (Finisher-V)
Causes:	a. The Staple HP Sensor was not turned ON although 0.5 sec had passed after the Staple Motor operation started. b. The staple unit does not come off the Staple HP Sensor when the Staple Motor has been driven for 400 msec. c. The staple unit does not come off the Staple HP Sensor when the Staple Motor has been driven for 0.4 seconds.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Staple HP Sensor 1. Finisher Controller PCB (UN3/J122) to Relay Connector (15P) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) 2. Relay Connector (15P) to Staple HP Sensor (PS27/J678) (Unit of replacement: CABLE, STAPLE SENSOR) - Harnesses from the Finisher Controller PCB to the Staple Unit 1. Finisher Controller PCB (UN3/J123) to Staple Driver PCB (UN6/J311) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) 2. Staple Driver PCB (UN6/J315 and J316) to Staple Unit (J672 and J673) (Unit of replacement: CABLE, STAPLE ASSEMBLY) - Staple Driver PCB (UN6) (Unit of replacement: STAPLE DRIVER PCB ASSEMBLY) - Staple HP Sensor (PS27) - Stapler (Unit of replacement: STAPLER ASSEMBLY) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Staple Position Switch (SW103) to the Finisher Controller PCB - Harnesses from the Staple Unit to the Finisher Controller PCB - Staple Position Switch (SW103) - Staple Unit - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Stapler Unit to the Stapler Relay PCB - Harnesses from the Stapler Unit Relay PCB to the Finisher Controller PCB - Stapler Unit - Stapler Unit Relay PCB (PCB102) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. 7. Error/Jam/Alarm

Error code:	531-8002-02
Description:	a. Staple HP error (Finisher-W1) b. Error in the Staple Motor (Finisher-X1) c. Error in the Staple Motor (Finisher-V)
Causes:	a. The Staple HP Sensor was not turned OFF although 0.5 sec had passed after the Staple Motor operation started. b. The Staple HP Sensor does nor detect the staple unit when the Staple Motor has been driven for 400 msec. c. The Staple HP Sensor does nor detect the staple unit when the Staple Motor has been driven for 0.4 seconds.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Staple HP Sensor 1. Finisher Controller PCB (UN3/J122) to Relay Connector (15P) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) 2. Relay Connector (15P) to Staple HP Sensor (PS27/J678) (Unit of replacement: CABLE, STAPLE SENSOR) - Harnesses from the Finisher Controller PCB to the Staple Unit 1. Finisher Controller PCB (UN3/J123) to Staple Driver PCB (UN6/J311) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) 2. Staple Driver PCB (UN6/J315 and J316) to Staple Unit (J672 and J673) (Unit of replacement: CABLE, STAPLE ASSEMBLY) - Staple Driver PCB (UN6) (Unit of replacement: STAPLE DRIVER PCB ASSEMBLY) - Staple HP Sensor (PS27) - Stapler (Unit of replacement: STAPLER ASSEMBLY) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Staple Unit to the Finisher Controller PCB - Staple Unit - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Stapler Unit to the Stapler Relay PCB - Harnesses from the Stapler Unit Relay PCB to the Finisher Controller PCB - Stapler Unit - Stapler Unit Relay PCB (PCB102) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	532-8001-02
Description:	a. Staple HP error (Finisher-W1) b. Error in the Stapler Shift Motor (Finisher-X1) c. Error in the Stapler Shift Motor (Finisher-V)
Causes:	a. The Staple HP Sensor was not turned ON although 10 sec had passed after the Staple Shift Motor operation started. b. The staple unit does not come off the Stapler Shift HP Sensor when the Staple Shift Motor has been driven for 5 seconds. c. The stapler unit does not come off the Stapler Shift HP Sensor when the Stapler Shift Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Staple HP Sensor 1. Finisher Controller PCB (UN3/J122) to Relay Connector (15P) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) 2. Relay Connector (15P) to Staple HP Sensor (PS27/J678) (Unit of replacement: CABLE, STAPLE SENSOR) - Harnesses from the Finisher Controller PCB to the Staple Unit 1. Finisher Controller PCB (UN3/J123) to Staple Driver PCB (UN6/J311) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) 2. Staple Driver PCB (UN6/J317) to Staple Move Motor (M21/J671) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) - Staple Driver PCB (UN6) (Unit of replacement: STAPLE DRIVER PCB ASSEMBLY) - Staple HP Sensor (PS27) - Staple Move Motor (M21) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Stapler Shift HP Sensor (S107) to the Finisher Controller PCB - Harnesses from the Staple Shift Motor (M107) to the Finisher Controller PCB - Stapler Shift HP Sensor (S107) - Staple Shift Motor (M107) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Stapler Shift HP Sensor (PS124) to the Finisher Controller PCB - Harnesses from the Stapler Shift Motor (M114) to the Finisher Controller PCB - Stapler Shift HP Sensor (PS124) - Stapler Shift Motor (M114) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	532-8002-02
Description:	a. Staple HP error (Finisher-W1) b. Error in the Stapler Shift Motor (Finisher-X1) c. Error in the Stapler Shift Motor (Finisher-V)
Causes:	a. The Staple HP Sensor was not turned OFF although 2 sec had passed after the Staple Shift Motor operation started. b. The Stapler Shift HP Sensor does not detect the staple unit when the Staple Shift Motor has been driven for 5 seconds. c. The Stapler Shift HP Sensor does not detect the stapler unit when the Stapler Shift Motor has been driven for 15 seconds.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Staple HP Sensor 1. Finisher Controller PCB (UN3/J122) to Relay Connector (15P) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) 2. Relay Connector (15P) to Staple HP Sensor (PS27/J678) (Unit of replacement: CABLE, STAPLE SENSOR) - Harnesses from the Finisher Controller PCB to the Staple Unit 1. Finisher Controller PCB (UN3/J123) to Staple Driver PCB (UN6/J311) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) 2. Staple Driver PCB (UN6/J317) to Staple Move Motor (M21/J671) (Unit of replacement: HOLDER, STAPLER CABLE, UPPER) - Staple Driver PCB (UN6) (Unit of replacement: STAPLE DRIVER PCB ASSEMBLY) - Staple HP Sensor (PS27) - Staple Move Motor (M21) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Stapler Shift HP Sensor (S107) to the Finisher Controller PCB - Harnesses from the Staple Shift Motor (M107) to the Finisher Controller PCB - Stapler Shift HP Sensor (S107) - Staple Shift Motor (M107) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Stapler Shift HP Sensor (PS124) to the Finisher Controller PCB - Harnesses from the Stapler Shift Motor (M114) to the Finisher Controller PCB - Stapler Shift HP Sensor (PS124) - Stapler Shift Motor (M114) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	535-0001-02
Description:	Error in the Swing Guide Motor (Finisher-X1)
Causes:	The swing guide does not come off the Swing Guide HP Sensor when the Swing Guide Motor has been driven for 3 seconds.
Remedy:	[Related parts] - Harnesses from the Swing Guide HP Sensor (S110) to the Finisher Controller PCB - Harnesses from the Swing Guide Motor (M110) to the Finisher Controller PCB - Swing Guide HP Sensor (S110) - Swing Guide Motor (M110) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

Error code:	535-0002-02
Description:	Error in the Swing Guide Motor (Finisher-X1)
Causes:	The Swing Guide HP Sensor does not detect the swing guide when the Swing Guide Motor has been driven for 3 seconds.
Remedy:	[Related parts] - Harnesses from the Swing Guide HP Sensor (S110) to the Finisher Controller PCB - Harnesses from the Swing Guide Motor (M110) to the Finisher Controller PCB - Swing Guide HP Sensor (S110) - Swing Guide Motor (M110) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

Error code:	535-8001-02
Description:	a. Swing Guide HP error (Finisher-W1) b. Error in the Swing Guide Motor (Finisher-V)
Causes:	a. The Swing Guide HP Sensor was not turned ON although 5 sec had passed after the Swing Guide Motor operation started. b. The swing guide does not come off the Swing Guide HP Sensor when the Swing Guide Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Swing Guide Motor 1. Finisher Controller PCB (UN3/J141) to Relay Connector (6P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (6P) to Relay Connector (6P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (6P) to Swing Guide Motor (M18/J630) (Unit of replacement: CABLE, YDGM) - Harnesses from the Finisher Controller PCB to the Swing Guide HP Sensor 1. Finisher Controller PCB (UN3/J106) to Relay Connector (25P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (25P) to Relay Connector (3P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (3P) to Swing Guide HP Sensor (PS44/J616) (Unit of replacement: OPERATION ASSEMBLY) - Swing Guide Motor (M18) - Swing Guide HP Sensor (PS44) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Swing Guide HP Sensor (PS119) to the Finisher Controller PCB - Harnesses from the Swing Guide Motor (M110) to the Finisher Controller PCB - Swing Guide HP Sensor (PS119) - Swing Guide Motor (M110) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	535-8002-02
Description:	a. Swing Guide HP error (Finisher-W1) b. Error in the Swing Guide Motor (Finisher-V)
Causes:	a.The Swing Guide HP Sensor was not turned OFF although 5 sec had passed after the Swing Guide Motor operation started. b. The Swing Guide HP Sensor does not detect the swing guide when the Swing Guide Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Swing Guide Motor 1. Finisher Controller PCB (UN3/J141) to Relay Connector (6P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (6P) to Relay Connector (6P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (6P) to Swing Guide Motor (M18/J630) (Unit of replacement: CABLE, YDGM) - Harnesses from the Finisher Controller PCB to the Swing Guide HP Sensor 1. Finisher Controller PCB (UN3/J106) to Relay Connector (25P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (25P) to Relay Connector (3P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (3P) to Swing Guide HP Sensor (PS44/J616) (Unit of replacement: OPERATION ASSEMBLY) - Swing Guide Motor (M18) - Swing Guide HP Sensor (PS44) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Swing Guide HP Sensor (PS119) to the Finisher Controller PCB - Harnesses from the Swing Guide Motor (M110) to the Finisher Controller PCB - Swing Guide HP Sensor (PS119) - Swing Guide Motor (M110) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	537-8001-02
Description:	a. Front Alignment Guide HP error (Finisher-W1) b. Error in the Rear Alignment Motor (Finisher-X1) c. Error in the Rear Alignment Motor (Finisher-V)
Causes:	a. The Front Alignment Guide HP Sensor was not turned ON although 5 sec had passed after the Front Alignment Motor started the operation. b. The rear alignment plate does not come off the Rear Alignment HP Sensor when the Rear Alignment Motor has been driven for 4 seconds. c. The rear alignment plate does not come off the Rear Alignment HP Sensor when the Rear Alignment Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Front Alignment Guide HP Sensor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (14P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (14P) to Front Alignment Guide HP Sensor (PS11/J605) (Unit of replacement: CABLE, FJOG) - Harnesses from the Finisher Controller PCB to the Front Alignment Motor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (14P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (14P) to Front Alignment Motor (M9/J606) (Unit of replacement: CABLE, FJOG) - Front Alignment Guide HP Sensor (PS11) - Front Alignment Motor (M9) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Rear Alignment HP Sensor (S109) to the Finisher Controller PCB - Harnesses from the Rear Alignment Motor (M109) to the Finisher Controller PCB - Rear Alignment HP Sensor (S109) - Rear Alignment Motor (M109) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Rear Alignment HP Sensor (PS116) to the Finisher Controller PCB - Harnesses from the Rear Alignment Motor (M108) to the Finisher Controller PCB - Rear Alignment HP Sensor (PS116) - Rear Alignment Motor (M108) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	537-8002-02
Description:	a. Front Alignment Guide HP error (Finisher-W1) b. Error in the Rear Alignment Motor (Finisher-X1) c. Error in the Rear Alignment Motor (Finisher-V)
Causes:	a. The Front Alignment Guide HP Sensor was not turned OFF although 5 sec had passed after the Front Alignment Motor operation started. b. The Rear Alignment HP Sensor does not detect the rear alignment plate when the Rear Alignment Motor has been driven for 4 seconds. c. The Rear Alignment HP Sensor does not detect the rear alignment plate when the Rear Alignment Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Front Alignment Guide HP Sensor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (14P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (14P) to Front Alignment Guide HP Sensor (PS11/J605) (Unit of replacement: CABLE, FJOG) - Harnesses from the Finisher Controller PCB to the Front Alignment Motor 1. Finisher Controller PCB (UN3/J139) to Relay Connector (31P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (31P) to Relay Connector (14P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (14P) to Front Alignment Motor (M9/J606) (Unit of replacement: CABLE, FJOG) - Front Alignment Guide HP Sensor (PS11) - Front Alignment Motor (M9) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Rear Alignment HP Sensor (S109) to the Finisher Controller PCB - Harnesses from the Rear Alignment Motor (M109) to the Finisher Controller PCB - Rear Alignment HP Sensor (S109) - Rear Alignment Motor (M109) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Rear Alignment HP Sensor (PS116) to the Finisher Controller PCB - Harnesses from the Rear Alignment Motor (M108) to the Finisher Controller PCB - Rear Alignment HP Sensor (PS116) - Rear Alignment Motor (M108) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	540-8001-02
Description:	a. Tray A (Upper Tray) lifting error (Finisher-W1) b. Tray 1 time out error (Finisher-X1) c. Stack tray time out error (Finisher-V)
Causes:	a. The Tray A Lifting Motor Rotation Sensor was not turned OFF although 800 sec had passed after the Tray A Lifting Motor started the operation. b. The tray 1 does not return to home position when the Tray 1 Shift Motor has been driven for 20 seconds. The tray 1 does not come off the Tray 1 Area Sensor at the same area when the Tray 1 Shift Motor has been driven for 4 seconds. c. The operation of the stack tray don`t finish when the Stack Tray Shift Motor has been driven for 28 seconds. The stack tray does not come off the same area when the Stack Tray Shift Motor has been driven for 15 seconds.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Tray A Lifting Motor 1. Finisher Controller PCB (UN3/J109A) to Tray A Motor Driver PCB (UN10/J292A) (Unit of replacement: CABLE ASSEMBLY, A) 2. Tray A Motor Driver PCB (UN10/J291A) to Tray A Lifting Motor (M22) (Unit of replacement: STEPPING MOTOR UNIT) - Tray A Lifting Motor Rotation Sensor (PS34) - Tray A Lifting Motor (M22) - Tray A Motor Driver PCB (UN10) (Unit of replacement: MOTOR DRIVER PCB ASSEMBLY) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Tray 1 Area Sensors (S122/S123/S124) to the Finisher Controller PCB - Harnesses from the Tray 1 Shift Motor (M105) to the Finisher Controller PCB - Tray 1 Area Sensors (S122/S123/S124) - Tray 1 Shift Motor (M105) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Stack Tray HP Sensor (PS106) to the Finisher Controller PCB - Harnesses from the Stack Tray Full Sensor 1/2/3 (PS107/PS108/PS109) to the Finisher Controller PCB - Harnesses from the Stack Tray Upper Limit Sensor (PS110) to the Finisher Controller PCB - Harnesses from the Stack Tray Shift Motor (M105) to the Finisher Controller PCB - Stack Tray HP Sensor (PS106) - Stack Tray Full Sensor 1/2/3 (PS107/PS108/PS109) - Stack Tray Shift Motor (M105) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	540-8002-02
Description:	a. Tray A (Upper Tray) area error (Finisher-W1) b. Tray 1 area error (Finisher-X1) c. Stack tray area error (Finisher-V)
Causes:	a. Tray A (Upper Tray) was detected as being at a lower position than Tray B (Lower Tray). The Tray A Position Sensor detected a non-contiguous area. b. The tray 1 detects the discontinuous area with the Tray 1 Area Sensors. c. The stack tray detects the discontinuous area during the operation.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harness between the Finisher Controller PCB (UN3/J109B) and the Tray A Third Position Sensor (PS49/J2534) (Unit of replacement: CABLE ASSEMBLY, A) - Harness between the Finisher Controller PCB (UN3/J109B) and the Tray A Fourth Position Sensor (PS50/J2533) (Unit of replacement: CABLE ASSEMBLY, A) - Tray A Third Position Sensor (PS49) - Tray A Fourth Position Sensor (PS50) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Tray 1 Area Sensors (S122/S123/S124) to the Finisher Controller PCB - Harnesses from the Tray 1 Shift Motor (M105) to the Finisher Controller PCB - Tray 1 Area Sensors (S122/S123/S124) - Tray 1 Shift Motor (M105) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Swing Guide Safety Switch (SW102) to the Finisher Controller PCB - Harnesses from the Stack Tray Shift Motor (M105) to the Finisher Controller PCB - Swing Guide Safety Switch (SW102) - Stack Tray Shift Motor (M105) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	540-8004-02
Description:	Stack tray paper surface detection error (Finisher-V)
Causes:	The Stack Tray Paper Surface Sensor does not turn off when the stack tray has been lowered for 10 seconds.
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Stack Tray Paper Surface Sensor (light-emitting) (PBA101) to the Finisher Controller PCB - Harnesses from the Stack Tray Paper Surface Sensor (light-receiving) (PBA102/PBA103) to the Finisher Controller PCB - Harnesses from the Stack Tray Shift Motor (M105) to the Finisher Controller PCB - Stack Tray Paper Surface Sensor (light-emitting) (PBA101) - Stack Tray Paper Surface Sensor (light-receiving) (PBA102/PBA103) - Stack Tray Shift Motor (M105) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	551-0003-02
Description:	a. Error in the Heat Exhaust Fan of the Finisher (Finisher-X1) b. Error in the Cooling Fan (Finisher-V)
Causes:	a. The lock signal is detected 1.2 seconds or more while the fan operates. b. The lock signal is detected 1.2 seconds or more while the fan operates.
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Heat Exhaust Fan (FAN102) to the Finisher Controller PCB - Heat Exhaust Fan (FAN102) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Cooling Fan (FM101) to the Finisher Controller PCB - Cooling Fan (FM101) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	551-0004-02
Description:	a. Error in the Heat Exhaust Fan of the Finisher (Finisher-X1) b. Error in the Cooling Fan of the Finisher (Finisher-V) c. Error in the Cooling Fan of the Paper Folding Unit (Paper Folding Unit-J1)
Causes:	a. The lock status is released when the fan stops. b. The lock status is released when the fan stops. c. The lock status is released when the fan rotates or the lock status is performed when the fan stops.
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Heat Exhaust Fan (FAN102) to the Finisher Controller PCB - Heat Exhaust Fan (FAN102) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Cooling Fan (FM101) to the Finisher Controller PCB - Cooling Fan (FM101) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. c. PFU-J1 [Related parts] - Harnesses from the Cooling Fan (F1) to the Finisher Controller PCB - Cooling Fan (F1) - Paper Folding Unit Controller PCB (PCB1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	553-8001-02
Description:	Error in the Lower Escape Delivery Shift Motor (Finisher-V)
Causes:	The lower escape delivery roller does not come off the Lower Escape Delivery Roller HP Sensor when the Lower Escape Delivery Shift Motor has been driven for 1 second.
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Lower Escape Delivery Roller HP Sensor (PS112) to the Finisher Controller PCB - Harnesses from the Lower Escape Delivery Shift Motor (M106) to the Finisher Controller PCB - Lower Escape Delivery Roller HP Sensor (PS112) - Lower Escape Delivery Shift Motor (M106) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	553-8002-02
Description:	Error in the Lower Escape Delivery Shift Motor (Finisher-V)
Causes:	The Lower Escape Delivery Roller HP Sensor does not detect the lower escape delivery roller when the Lower Escape Delivery Shift Motor has been driven for 1 second.
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Lower Escape Delivery Roller HP Sensor (PS112) to the Finisher Controller PCB - Harnesses from the Lower Escape Delivery Shift Motor (M106) to the Finisher Controller PCB - Lower Escape Delivery Roller HP Sensor (PS112) - Lower Escape Delivery Shift Motor (M106) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	553-8011-02
Description:	Error in the Flapper Motor (Finisher-V)
Causes:	The flapper does not come off the Flapper HP Sensor when the Flapper Motor has been driven for 1 second.
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Flapper HP Sensor (PS105) to the Finisher Controller PCB - Harnesses from the Flapper Motor (M104) to the Finisher Controller PCB - Flapper HP Sensor (PS105) - Flapper Motor (M104) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	553-8012-02
Description:	Error in the Flapper Motor (Finisher-V)
Causes:	The Flapper HP Sensor does not detect the flapper when the Flapper Motor has been driven for 1 second.
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Flapper HP Sensor (PS105) to the Finisher Controller PCB - Harnesses from the Flapper Motor (M104) to the Finisher Controller PCB - Flapper HP Sensor (PS105) - Flapper Motor (M104) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	553-80F1-02
Description:	Error in the Saddle Feed/Paddle Motor (Finisher-V)
Causes:	The paddle does not come off the Saddle Paddle HP Sensor when the Saddle Feed/Paddle Motor has been driven for 1 second.
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Paddle HP Sensor (PS206) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Feed/Paddle Motor (M201) to the Saddle Stitcher Controller PCB - Saddle Paddle HP Sensor (PS206) - Saddle Feed/Paddle Motor (M201) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	553-80F2-02
Description:	Error in the Saddle Feed/Paddle Motor (Finisher-V)
Causes:	The Saddle Paddle HP Sensor does not detect the paddle when the Saddle Feed/Paddle Motor has been driven for 1 second.
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Paddle HP Sensor (PS206) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Feed/Paddle Motor (M201) to the Saddle Stitcher Controller PCB - Saddle Paddle HP Sensor (PS206) - Saddle Feed/Paddle Motor (M201) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	554-8001-02
Description:	Safety switch ON error (Finisher-V)
Causes:	The Swing Guide Safety Switch is turned ON for 0.3 seconds. The Front Cover Switch is turned OFF for 0.3 seconds when the Front Cover Sensor is ON.
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Swing Guide Safety Switch (SW102) to the Finisher Controller PCB - Harnesses from the Stack Tray Shift Motor (M105) to the Finisher Controller PCB - Swing Guide Safety Switch (SW102) - Stack Tray Shift Motor (M105) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	577-0002-02
Description:	Paddle Motor error (Finisher-H1)
Causes:	- The Return Belt HP Sensor was not turned ON although 1 second had passed after the Paddle Motor operation started. - The last paddle operation is not finished when driving the Paddle Motor.
Remedy:	[Related parts] - Harnesses and connectors from the Finisher Controller PCB to the Return Belt HP Sensor - Harnesses and connectors from the Finisher Controller PCB to the Paddle Motor - Return Belt HP Sensor (PS3) - Paddle Motor (M10) - Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual.

Error code:	577-8001-02
Description:	a. Paddle rotation HP error (Finisher-W1) b. Error in the Stack Delivery/Paddle Motor (Finisher-V)
Causes:	a. The Paddle Rotation HP Sensor was not turned ON although 5 sec had passed after the Paddle Rotation Motor started the operation. b. The paddle does not come off the Paddle HP Sensor when the Stack Delivery/Paddle Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Paddle Rotation Motor 1. Finisher Controller PCB (UN3/J140) to Relay Connector (19P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (19P) to Relay Connector (5P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (5P) to Paddle Rotation Motor (M14/J628) (Unit of replacement: CABLE, PDLROT- M-T) - Harnesses from the Finisher Controller PCB to the Paddle Rotation HP Sensor 1. Finisher Controller PCB (UN3/J106) to Relay Connector (25P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (25P) to Relay Connector (3P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (3P) to Paddle Rotation HP Sensor (PS20/J619) (Unit of replacement: OPERATION ASSEMBLY) - Paddle Rotation Motor (M14) - Paddle Rotation HP Sensor (PS20) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Paddle HP Sensor (PS120) to the Finisher Controller PCB - Harnesses from the Stack Delivery/Paddle Motor (M103) to the Finisher Controller PCB - Paddle HP Sensor (PS120) - Stack Delivery/Paddle Motor (M103) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	577-8002-02
Description:	a. Paddle rotation HP error (Finisher-W1) b. Error in the Stack Delivery/Paddle Motor (Finisher-V)
Causes:	a. The Paddle Rotation HP Sensor was not turned OFF although 5 sec had passed after the Paddle Rotation Motor started the operation. b. The Paddle HP Sensor does not detect the paddle when the Stack Delivery/Paddle Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Paddle Rotation Motor 1. Finisher Controller PCB (UN3/J140) to Relay Connector (19P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (19P) to Relay Connector (5P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (5P) to Paddle Rotation Motor (M14/J628) (Unit of replacement: CABLE, PDLROT- M-T) - Harnesses from the Finisher Controller PCB to the Paddle Rotation HP Sensor 1. Finisher Controller PCB (UN3/J106) to Relay Connector (25P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (25P) to Relay Connector (3P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (3P) to Paddle Rotation HP Sensor (PS20/J619) (Unit of replacement: OPERATION ASSEMBLY) - Paddle Rotation Motor (M14) - Paddle Rotation HP Sensor (PS20) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Paddle HP Sensor (PS120) to the Finisher Controller PCB - Harnesses from the Stack Delivery/Paddle Motor (M103) to the Finisher Controller PCB - Paddle HP Sensor (PS120) - Stack Delivery/Paddle Motor (M103) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	578-8001-02
Description:	a. Feed knurling HP error (Finisher-W1) b. Error in the Paper Return Guide Motor (Finisher- X1) c. Error in the Return Roller Lift Motor (Finisher-V)
Causes:	a. The Feed Belt HP Sensor was not turned ON although 5 sec had passed after the Feed Shift Motor started the operation. b. The paper return guide does not come off the Paper Return Guide HP Sensor when the Paper Return Guide Motor has been driven for 3 seconds. c. The return roller does not come off the Return Roller HP Sensor when the Return Roller Lift Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Feed Belt Shift Motor 1. Finisher Controller PCB (UN3/J129) to Relay Connector (11P) (Unit of replacement: CABLE, FEED UNIT) 2. Relay Connector (11P) to Feed Belt Shift Motor (M17/J640) (Unit of replacement: CABLE, KNURLED UNIT) - Harnesses from the Finisher Controller PCB to the Feed Belt HP Sensor 1. Finisher Controller PCB (UN3/J129) to Relay Connector (11P) (Unit of replacement: CABLE, FEED UNIT) 2. Relay Connector (11P) to Feed Belt HP Sensor (PS25/J639) (Unit of replacement: CABLE, KNURLED UNIT) - Feed Belt Shift Motor (M17) - Feed Belt HP Sensor (PS25) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Paper Return Guide HP Sensor (S112) to the Finisher Controller PCB - Harnesses from the Paper Return Guide Motor (M112) to the Finisher Controller PCB - Paper Return Guide HP Sensor (S112) - Paper Return Guide Motor (M112) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Return Roller HP Sensor (PS121) to the Finisher Controller PCB - Harnesses from the Return Roller Lift Motor (M111) to the Finisher Controller PCB - Return Roller HP Sensor (PS121) - Return Roller Lift Motor (M111) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	578-8002-02
Description:	a. Feed knurling HP error (Finisher-W1) b. Error in the Paper Return Guide Motor (Finisher- X1) c. Error in the Return Roller Lift Motor (Finisher-V)
Causes:	a. The Feed Belt HP Sensor was not turned OFF although 5 sec had passed after the Feed Shift Motor started the operation. b. The Paper Return Guide HP Sensor does not detect the paper return guide when the Paper Return Guide Motor has been driven for 3 seconds. c. The Return Roller HP Sensor does not detect the return roller when the Return Roller Lift Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Finisher Controller PCB to the Feed Belt Shift Motor 1. Finisher Controller PCB (UN3/J129) to Relay Connector (11P) (Unit of replacement: CABLE, FEED UNIT) 2. Relay Connector (11P) to Feed Belt Shift Motor (M17/J640) (Unit of replacement: CABLE, KNURLED UNIT) - Harnesses from the Finisher Controller PCB to the Feed Belt HP Sensor 1. Finisher Controller PCB (UN3/J129) to Relay Connector (11P) (Unit of replacement: CABLE, FEED UNIT) 2. Relay Connector (11P) to Feed Belt HP Sensor (PS25/J639) (Unit of replacement: CABLE, KNURLED UNIT) - Feed Belt Shift Motor (M17) - Feed Belt HP Sensor (PS25) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Paper Return Guide HP Sensor (S112) to the Finisher Controller PCB - Harnesses from the Paper Return Guide Motor (M112) to the Finisher Controller PCB - Paper Return Guide HP Sensor (S112) - Paper Return Guide Motor (M112) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Return Roller HP Sensor (PS121) to the Finisher Controller PCB - Harnesses from the Return Roller Lift Motor (M111) to the Finisher Controller PCB - Return Roller HP Sensor (PS121) - Return Roller Lift Motor (M111) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	57B-8001-02
Description:	a. Paper Trailing Edge Drop Guide HP error (Finisher-W1) b. Error in the Paper Trailing Edge Pushing Guide Motor (Finisher-X1) c. Error in the Paper End Pushing Guide Motor (Finisher- V)
Causes:	a. The Paper Trailing Edge Drop Guide HP Sensor was not turned ON although 5 sec had passed after the Paper Trailing Edge Drop Motor started the operation. b. The paper trailing edge pushing guide does not come off the Paper Trailing Edge Pushing Guide HP Sensor when the Paper Trailing Edge Pushing Guide Motor has been driven for 3 seconds. c. The paper end pushing guide does not come off the Paper End Pushing Guide HP Sensor when the Paper End Pushing Guide Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Feed Motor Driver PCB to the Paper Trailing Edge Drop Guide HP Sensor 1. Feed Motor Driver PCB (UN5/J277) to Relay Connector (7P) 2. Relay Connector (7P) to Paper Trailing Edge Drop Guide HP Sensor (PS24/J510) (Unit of replacement: CABLE, DNSORT SENSOR) - Paper Trailing Edge Drop Motor (M16) - Paper Trailing Edge Drop Guide HP Sensor (PS24) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Paper Trailing Edge Pushing Guide HP Sensor (S113) to the Finisher Controller PCB - Harnesses from the Paper Trailing Edge Pushing Guide Motor (M113) to the Finisher Controller PCB - Paper Trailing Edge Pushing Guide HP Sensor (S113) - Paper Trailing Edge Pushing Guide Motor (M113) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Paper End Pushing Guide HP Sensor (PS122) to the Finisher Controller PCB - Harnesses from the Paper End Pushing Guide Motor (M112) to the Finisher Controller PCB - Paper End Pushing Guide HP Sensor (PS122) - Paper End Pushing Guide Motor (M112) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	57B-8002-02
Description:	a. Paper Trailing Edge Drop Guide HP error (Finisher-W1) b. Error in the Paper Trailing Edge Pushing Guide Motor (Finisher-X1) c. Error in the Paper End Pushing Guide Motor (Finisher- V)
Causes:	a. The Paper Trailing Edge Drop Guide HP Sensor was not turned OFF although 5 sec had passed after the Paper Trailing Edge Drop Motor started the operation. b. The Paper Trailing Edge Pushing Guide HP Sensor does not detect the paper trailing edge pushing guide when the Paper Trailing Edge Pushing Guide Motor has been driven for 3 seconds. c. The Paper End Pushing Guide HP Sensor does not detect the paper end pushing guide when the Paper End Pushing Guide Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Feed Motor Driver PCB to the Paper Trailing Edge Drop Guide HP Sensor 1. Feed Motor Driver PCB (UN5/J277) to Relay Connector (7P) 2. Relay Connector (7P) to Paper Trailing Edge Drop Guide HP Sensor (PS24/J510) (Unit of replacement: CABLE, DNSORT SENSOR) - Paper Trailing Edge Drop Motor (M16) - Paper Trailing Edge Drop Guide HP Sensor (PS24) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Paper Trailing Edge Pushing Guide HP Sensor (S113) to the Finisher Controller PCB - Harnesses from the Paper Trailing Edge Pushing Guide Motor (M113) to the Finisher Controller PCB - Paper Trailing Edge Pushing Guide HP Sensor (S113) - Paper Trailing Edge Pushing Guide Motor (M113) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Paper End Pushing Guide HP Sensor (PS122) to the Finisher Controller PCB - Harnesses from the Paper End Pushing Guide Motor (M112) to the Finisher Controller PCB - Paper End Pushing Guide HP Sensor (PS122) - Paper End Pushing Guide Motor (M112) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	583-8001-02
Description:	a. Stack Delivery Auxiliary Tray HP error (Finisher-W1) b. Error in the Tray Auxiliary Guide Motor (Finisher-X1) c. Error in the Tray Auxiliary Guide Motor (Finisher-V)
Causes:	a. The Stack Delivery Auxiliary Tray HP Sensor was not turned ON although 5 sec had passed after the Stack Delivery Auxiliary Tray Motor started the operation. b. The tray auxiliary guide does not come off the Tray Auxiliary Guide Front/Rear HP Sensors when the Tray Auxiliary Guide Motor has been driven for 3 seconds. c. The tray auxiliary guides don`t come off the Front/Rear Tray Auxiliary Guide HP Sensors when the Tray Auxiliary Guide Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses connecting the Stack Delivery Auxiliary Tray Motor (M13/J629), the Relay Connector (J629/J633) and the Finisher Controller PCB (UN3/J140) - Harnesses from the Finisher Controller PCB to the Stack Delivery Auxiliary Tray Motor 1. Finisher Controller PCB (UN3/J140) to Relay Connector (19P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (19P) to Stack Delivery Auxiliary Tray Motor (M13/J629) (Unit of replacement: MOTOR, STEPPING, DC) - Harnesses from the Finisher Controller PCB to the Stack Delivery Auxiliary Tray HP Sensor 1. Finisher Controller PCB (UN3/J106) to Relay Connector (25P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (25P) to Relay Connector (4P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (4P) to Stack Delivery Auxiliary Tray HP Sensor (PS14/J617) (Unit of replacement: TRAY AUXILIARY PLATE ASSEMBLY) - Stack Delivery Auxiliary Tray Motor (M13) - Stack Delivery Auxiliary Tray HP Sensor (PS14) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Tray Auxiliary Guide Front HP Sensor (S137) to the Finisher Controller PCB - Harnesses from the Tray Auxiliary Guide Rear HP Sensor (S136) to the Finisher Controller PCB - Tray Auxiliary Guide Motor (M120) - Tray Auxiliary Guide Front HP Sensor (S137) - Tray Auxiliary Guide Rear HP Sensor (S136) - Tray Auxiliary Guide Motor (M120) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Front Tray Auxiliary Guide HP Sensor (PS117) to the Finisher Controller PCB - Harnesses from the Rear Tray Auxiliary Guide HP Sensor (PS118) to the Finisher Controller PCB - Harnesses from the Tray Auxiliary Guide Motor (M109) to the Finisher Controller PCB - Front Tray Auxiliary Guide HP Sensor (PS117) - Rear Tray Auxiliary Guide HP Sensor (PS118) - Tray Auxiliary Guide Motor (M109) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	583-8002-02
Description:	a. Stack Delivery Auxiliary Tray HP error (Finisher-W1) b. Error in the Tray Auxiliary Guide Motor (Finisher-X1) c. Error in the Tray Auxiliary Guide Motor (Finisher-V)
Causes:	a. The Stack Delivery Auxiliary Tray HP Sensor was not turned OFF although 5 sec had passed after the Stack Delivery Auxiliary Tray Motor started the operation. b. The Tray Auxiliary Guide Front/Rear HP Sensors does nor detect the tray auxiliary guide when the Tray Auxiliary Guide Motor has been driven for 3 seconds. c. The Front/Rear Tray Auxiliary Guide HP Sensors don`t detect the tray auxiliary guides when the Tray Auxiliary Guide Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses connecting the Stack Delivery Auxiliary Tray Motor (M13/J629), the Relay Connector (J629/J633) and the Finisher Controller PCB (UN3/J140) - Harnesses from the Finisher Controller PCB to the Stack Delivery Auxiliary Tray Motor 1. Finisher Controller PCB (UN3/J140) to Relay Connector (19P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (19P) to Stack Delivery Auxiliary Tray Motor (M13/J629) (Unit of replacement: MOTOR, STEPPING, DC) - Harnesses from the Finisher Controller PCB to the Stack Delivery Auxiliary Tray HP Sensor 1. Finisher Controller PCB (UN3/J106) to Relay Connector (25P) (Unit of replacement: CABLE, JOG-T) 2. Relay Connector (25P) to Relay Connector (4P) (Unit of replacement: CABLE, JOG-U) 3. Relay Connector (4P) to Stack Delivery Auxiliary Tray HP Sensor (PS14/J617) (Unit of replacement: TRAY AUXILIARY PLATE ASSEMBLY) - Stack Delivery Auxiliary Tray Motor (M13) - Stack Delivery Auxiliary Tray HP Sensor (PS14) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Tray Auxiliary Guide Front HP Sensor (S137) to the Finisher Controller PCB - Harnesses from the Tray Auxiliary Guide Rear HP Sensor (S136) to the Finisher Controller PCB - Tray Auxiliary Guide Motor (M120) - Tray Auxiliary Guide Front HP Sensor (S137) - Tray Auxiliary Guide Rear HP Sensor (S136) - Tray Auxiliary Guide Motor (M120) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Front Tray Auxiliary Guide HP Sensor (PS117) to the Finisher Controller PCB - Harnesses from the Rear Tray Auxiliary Guide HP Sensor (PS118) to the Finisher Controller PCB - Harnesses from the Tray Auxiliary Guide Motor (M109) to the Finisher Controller PCB - Front Tray Auxiliary Guide HP Sensor (PS117) - Rear Tray Auxiliary Guide HP Sensor (PS118) - Tray Auxiliary Guide Motor (M109) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	590-0002-02
Description:	Error in the Punch (Inner Puncher-B1)
Causes:	The Puncher does not come on the Punch HP Sensor after driving stopped during initialization. The Punch HP Sensor does not detect the punch when the Punch Motor has been driven for 0.4 seconds for returning the punch after the punch jam.
Remedy:	[Related parts] - Harnesses from the Punch HP Sensor 1 (S5) to the Puncher Relay PCB - Harnesses from the Punch HP Sensor 2 (S6) to the Puncher Relay PCB - Harnesses from the Punch Motor Clock Sensor (S7) to the Puncher Relay PCB - Harnesses from the Punch Motor (M2) to the Puncher Relay PCB - Punch HP Sensor 1 (S5) - Punch HP Sensor 2 (S6) - Punch Motor Clock Sensor (S7) - Punch Motor (M2) - Puncher Relay PCB (PCB5) - Puncher Controller PCB (PCB1) - Finisher Controller PCB (PCB1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	590-8001-02
Description:	a. Punch Motor HP error (Puncher Unit-BS1/BT1/BU1) b. Error in the Punch Motor (Puncher Unit-BE1/BF1/BG1/BH1) c. Error in the Punch Motor (Puncher Unit-A1)
Causes:	a. The Punch Motor HP Sensor was not turned ON although 500 sec had passed after the Punch Motor started the operation. b. During initialization, the Punch HP Sensor does not detect the Puncher when the Punch Motor has been driven for 500 msec. after the Puncher has come off the Punch HP Sensor. After initialization, the Punch Motor does not return to home position. c. The punch does not come off the Punch HP Sensor when the Punch Motor has been driven for 0.2 seconds.
Remedy:	a. PUNCHER UNIT-BS1/BT1/BU1 [Related parts] - Harness between the Finisher Controller PCB (UN3/J131) and the Punch Motor (M24/J571) (Unit of replacement: CABLE, PUNCH) - Harness between the Finisher Controller PCB (UN3/J130) and the Punch Motor Clock Sensor (PS38/J575) (Unit of replacement: CABLE, PUNCH) - Harness between the Finisher Controller PCB (UN3/J130) and the Punch Front Sensor (PS37/ J573) (Unit of replacement: CABLE, PUNCH) - Harness between the Finisher Controller PCB (UN3/J130) and the Punch 2/3 Hole Sensor (PS39/ J572) (Unit of replacement: CABLE, PUNCH) - Harness between the Finisher Controller PCB (UN3/J130) and the Punch Motor HP Sensor (PS36/J574) (Unit of replacement: CABLE, PUNCH) - Punch Motor Clock Sensor (PS38) (Unit of replacement: IC, PHOTO-INTERRUPTER) - Punch Front Sensor (PS37) (Unit of replacement: IC, PHOTO-INTERRUPTER) - Punch 2/3 Hole Sensor (PS39) (Unit of replacement: IC, PHOTO-INTERRUPTER) - Punch Motor HP Sensor (PS36) (Unit of replacement: IC, PHOTO-INTERRUPTER) - Punch Motor (M24) (Unit of replacement: MOTOR, STEPPING, DC) - Punch Unit (Unit of replacement: PUNCHER UNIT-BS1/BT1/BU1) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. Puncher Unit-BE1/BF1/BG1/BH1 [Related parts] - Harnesses from the Punch HP Sensor (S104) to the Puncher Driver PCB - Harnesses from the Punch Motor Clock Sensor (S105) to the Puncher Driver PCB - Harnesses from the Punch Motor (M102) to the Puncher Driver PCB - Punch HP Sensor (S104) - Punch Motor Clock Sensor (S105) - Punch Motor (M102) - Puncher Driver PCB (PCB1) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. Puncher Unit-A1 [Related parts] - Harnesses from the Punch HP Sensor 1 (PS303) to the Puncher Relay PCB - Harnesses from the Punch HP Sensor 2 (PS304) to the Puncher Relay PCB - Harnesses from the Punch Motor Clock Sensor (PS305) to the Puncher Relay PCB - Harnesses from the Punch Motor (M301) to the Puncher Relay PCB - Punch HP Sensor 1 (PS303) - Punch HP Sensor 2 (PS304) - Punch Motor Clock Sensor (PS305) - Punch Motor (M301) - Puncher Relay PCB (PCB302) - Puncher Controller PCB (PCB301) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	590-8002-02
Description:	a. Punch Motor HP error (Puncher Unit-BS1/BT1/BU1) b. Error in the Punch Motor (Puncher Unit-BE1/BF1/BG1/BH1) c. Error in the Punch Motor (Puncher Unit-A1)
Causes:	a. The Punch Motor HP Sensor was not turned OFF although 500 sec had passed after the Punch Motor started the operation. b. The Puncher does not come off the Punch HP Sensor when the Punch Motor has been driven for 200 msec. The Puncher does not come off the Punch HP Sensor during initialization. c. The Punch HP Sensor does not detect the punch during initialization. The Punch HP Sensor does not detect the punch when the Punch Motor has been driven for 0.4 seconds for returning the punch after the punch jam.
Remedy:	a. PUNCHER UNIT-BS1/BT1/BU1 [Related parts] - Harness between the Finisher Controller PCB (UN3/J131) and the Punch Motor (M24/J571) (Unit of replacement: CABLE, PUNCH) - Harness between the Finisher Controller PCB (UN3/J130) and the Punch Motor Clock Sensor (PS38/J575) (Unit of replacement: CABLE, PUNCH) - Harness between the Finisher Controller PCB (UN3/J130) and the Punch Front Sensor (PS37/ J573) (Unit of replacement: CABLE, PUNCH) - Harness between the Finisher Controller PCB (UN3/J130) and the Punch 2/3 Hole Sensor (PS39/ J572) (Unit of replacement: CABLE, PUNCH) - Harness between the Finisher Controller PCB (UN3/J130) and the Punch Motor HP Sensor (PS36/J574) (Unit of replacement: CABLE, PUNCH) - Punch Motor Clock Sensor (PS38) (Unit of replacement: IC, PHOTO-INTERRUPTER) - Punch Front Sensor (PS37) (Unit of replacement: IC, PHOTO-INTERRUPTER) - Punch 2/3 Hole Sensor (PS39) (Unit of replacement: IC, PHOTO-INTERRUPTER) - Punch Motor HP Sensor (PS36) (Unit of replacement: IC, PHOTO-INTERRUPTER) - Punch Motor (M24) (Unit of replacement: MOTOR, STEPPING, DC) - Punch Unit (Unit of replacement: PUNCHER UNIT-BS1/BT1/BU1) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. Puncher Unit-BE1/BF1/BG1/BH1 [Related parts] - Harnesses from the Punch HP Sensor (S104) to the Puncher Driver PCB - Harnesses from the Punch Motor Clock Sensor (S105) to the Puncher Driver PCB - Harnesses from the Punch Motor (M102) to the Puncher Driver PCB - Punch HP Sensor (S104) - Punch Motor Clock Sensor (S105) - Punch Motor (M102) - Puncher Driver PCB (PCB1) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. Puncher Unit-A1 [Related parts] - Harnesses from the Punch HP Sensor 1 (PS303) to the Puncher Relay PCB - Harnesses from the Punch HP Sensor 2 (PS304) to the Puncher Relay PCB - Harnesses from the Punch Motor Clock Sensor (PS305) to the Puncher Relay PCB - Harnesses from the Punch Motor (M301) to the Puncher Relay PCB - Punch HP Sensor 1 (PS303) - Punch HP Sensor 2 (PS304) - Punch Motor Clock Sensor (PS305) - Punch Motor (M301) - Puncher Relay PCB (PCB302) - Puncher Controller PCB (PCB301) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	593-0001-02
Description:	Error in the Punch Horizontal Registration Motor (Inner Puncher-B1)
Causes:	The Horizontal Registration HP Sensor does not detect the punch unit when shifting the punch unit by 37mm toward rear.
Remedy:	[Related parts] - Harnesses from the Horizontal Registration HP Sensor (S1) to the Puncher Controller PCB - Harnesses from the Punch Horizontal Registration Motor (M1) to the Puncher Controller PCB - PHorizontal Registration HP Sensor (S1) - Punch Horizontal Registration Motor (M1) - Puncher Controller PCB (PCB1) - Finisher Controller PCB (PCB1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	593-0002-02
Description:	Error in the Punch Horizontal Registration Motor (Inner Puncher-B1)
Causes:	The Horizontal Registration HP Sensor does not detect the punch unit when shifting the punch unit by 37mm toward rear.
Remedy:	[Related parts] - Harnesses from the Horizontal Registration HP Sensor (S1) to the Puncher Controller PCB - Harnesses from the Punch Horizontal Registration Motor (M1) to the Puncher Controller PCB - PHorizontal Registration HP Sensor (S1) - Punch Horizontal Registration Motor (M1) - Puncher Controller PCB (PCB1) - Finisher Controller PCB (PCB1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	593-8001-02
Description:	a. Error in the Punch Slide Motor (Puncher Unit-BE1/BF1/BG1/BH1) b. Error in the Punch Shift Motor (Puncher Unit-A1)
Causes:	a. The punch unit does not come off the Horizontal Registration HP Sensor when the Punch Slide Motor has been driven for 680 msec. b. The punch unit does not come off the Punch Slide HP Sensor when shifting the punch unit by 9mm toward rear.
Remedy:	a. Puncher Unit-BE1/BF1/BG1/BH1 [Related parts] - Harnesses from the Horizontal Registration HP Sensor (S101) to the Puncher Driver PCB - Harnesses from the Punch Slide Motor (M101) to the Puncher Driver PCB - Horizontal Registration HP Sensor (S101) - Punch Slide Motor (M101) - Puncher Driver PCB (PCB1) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. Puncher Unit-A1 [Related parts] - Harnesses from the Punch Slide HP Sensor (PS302) to the Puncher Controller PCB - Harnesses from the Punch Shift Motor (M302) to the Puncher Controller PCB - Punch Slide HP Sensor (PS302) - Punch Shift Motor (M302) - Puncher Controller PCB (PCB301) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	593-8002-02
Description:	a. Error in the Punch Slide Motor (Puncher Unit-BE1/BF1/BG1/BH1) b. Error in the Punch Shift Motor (Puncher Unit-A1)
Causes:	a. The Horizontal Registration HP Sensor does not detect the punch unit when the Punch Slide Motor has been driven for 3.3 seconds. b. The Punch Slide HP Sensor does not detect the punch unit when shifting the punch unit by 37mm toward front.
Remedy:	a. Puncher Unit-BE1/BF1/BG1/BH1 [Related parts] - Harnesses from the Horizontal Registration HP Sensor (S101) to the Puncher Driver PCB - Harnesses from the Punch Slide Motor (M101) to the Puncher Driver PCB - Horizontal Registration HP Sensor (S101) - Punch Slide Motor (M101) - Puncher Driver PCB (PCB1) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. Puncher Unit-A1 [Related parts] - Harnesses from the Punch Slide HP Sensor (PS302) to the Puncher Controller PCB - Harnesses from the Punch Shift Motor (M302) to the Puncher Controller PCB - Punch Slide HP Sensor (PS302) - Punch Shift Motor (M302) - Puncher Controller PCB (PCB301) - Finisher Controller PCB (PCB101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F0-8001-02
Description:	a. Saddle Leading Edge Stopper HP error (Finisher-W1) b. Error in the Saddle Lead Edge Stopper Motor (Finisher-X1) c. Error in the Saddle Paper End Stopper Motor (Finisher-V)
Causes:	a. The Saddle Leading Edge Stopper Home Position Sensor was not turned ON although 5.5 sec had passed after the Saddle Leading Edge Stopper started the operation. b. The Saddle Lead Edge Stopper HP Sensor does not detect the Saddle lead edge stopper when the Saddle lead edge stopper has been moved for 182 mm by Saddle Lead Edge Stopper Motor. c. The saddle paper end stopper does not come off the Saddle Paper End Stopper HP Sensor when the Saddle Paper End Stopper Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Leading Edge Stopper Home Position Sensor 1. Saddle Stitcher Controller PCB (UN101/J213) to Relay Connector (17P) (Unit of replacement: CABLE, SADDLE SENSOR, FRONT) 2. Relay Connector (17P) to Relay Connector (17P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (17P) to Saddle Leading Edge Stopper Home Position Sensor (PS105/J929) (Unit of replacement: EDGE STOPPER ASSEMBLY) - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Lead Edge Stopper Motor 1. Saddle Stitcher Controller PCB (UN101/J213) to Relay Connector (17P) (Unit of replacement: CABLE, SADDLE SENSOR, FRONT) 2. Relay Connector (17P) to Relay Connector (17P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (17P) to Saddle Lead Edge Stopper Motor (M103/J925) (Unit of replacement: EDGE STOPPER ASSEMBLY) - Saddle Leading Edge Stopper Home Position Sensor (PS105) - Saddle Leading Edge Stopper Motor (M103) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Lead Edge Stopper HP Sensor (S205) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Lead Edge Stopper Motor (M203) to the Saddle Stitcher Controller PCB - Saddle Lead Edge Stopper HP Sensor (S205) - Saddle Lead Edge Stopper Motor (M203) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Paper End Stopper HP Sensor (PS210) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper End Stopper Motor (M206) to the Saddle Stitcher Controller PCB - Saddle Paper End Stopper HP Sensor (PS210) - Saddle Paper End Stopper Motor (M206) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F0-8002-02
Description:	a. Saddle Leading Edge Stopper HP error (Finisher-W1) b. Error in the Saddle Lead Edge Stopper Motor (Finisher-X1) c. Error in the Saddle Paper End Stopper Motor (Finisher-V)
Causes:	a. The Saddle Leading Edge Stopper Home Position Sensor was not turned OFF although 5.5 sec had passed after the Saddle Leading Edge Stopper started the operation. b. The Saddle lead edge stopper does not come off the Saddle Lead Edge Stopper HP Sensor when the Saddle Lead Edge Stopper Motor has been driven for 50 pulses. c. The Saddle Paper End Stopper HP Sensor does not detect the saddle paper end stopper when the Saddle Paper End Stopper Motor has been driven for 4 seconds.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Leading Edge Stopper Home Position Sensor 1. Saddle Stitcher Controller PCB (UN101/J213) to Relay Connector (17P) (Unit of replacement: CABLE, SADDLE SENSOR, FRONT) 2. Relay Connector (17P) to Relay Connector (17P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (17P) to Saddle Leading Edge Stopper Home Position Sensor (PS105/J929) (Unit of replacement: EDGE STOPPER ASSEMBLY) - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Lead Edge Stopper Motor 1. Saddle Stitcher Controller PCB (UN101/J213) to Relay Connector (17P) (Unit of replacement: CABLE, SADDLE SENSOR, FRONT) 2. Relay Connector (17P) to Relay Connector (17P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (17P) to Saddle Lead Edge Stopper Motor (M103/J925) (Unit of replacement: EDGE STOPPER ASSEMBLY) - Saddle Leading Edge Stopper Home Position Sensor (PS105) - Saddle Leading Edge Stopper Motor (M103) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Lead Edge Stopper HP Sensor (S205) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Lead Edge Stopper Motor (M203) to the Saddle Stitcher Controller PCB - Saddle Lead Edge Stopper HP Sensor (S205) - Saddle Lead Edge Stopper Motor (M203) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Paper End Stopper HP Sensor (PS210) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper End Stopper Motor (M206) to the Saddle Stitcher Controller PCB - Saddle Paper End Stopper HP Sensor (PS210) - Saddle Paper End Stopper Motor (M206) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F1-8003-02
Description:	Saddle Delivery Motor clock error (Finisher-V)
Causes:	The lock state of Saddle Delivery Motor is detected 0.2 seconds or more while the motor operates.
Remedy:	STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Delivery Motor Clock Sensor (PS211) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Delivery Motor (M207) to the Saddle Stitcher Controller PCB - Saddle Delivery Motor Clock Sensor (PS211) - Saddle Delivery Motor (M207) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F3-8001-02
Description:	a. Saddle Alignment Plate HP error (Finisher-W1) b. Error in the Saddle Alignment Guide Motor (Finisher-X1) c. Error in the Saddle Alignment Motor (Finisher-V)
Causes:	a. The Saddle Alignment Plate HP Sensor was not turned ON although 1.5 sec had passed after the Saddle Alignment Guide Motor started the operation. b. The Saddle Alignment Plate HP Sensor does not detect the saddle alignment guide when the saddle alignment guide has been moved for 177 mm by Saddle Alignment Guide Motor. c. The saddle alignment plate does not come off the Saddle Alignment HP Sensor when the Saddle Alignment Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Alignment Plate HP Sensor 1. Saddle Stitcher Controller PCB (UN101/J213) to Relay Connector (17P) (Unit of replacement: CABLE, SADDLE SENSOR, FRONT) 2. Relay Connector (17P) to Relay Connector (17P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (17P) to Saddle Alignment Plate HP Sensor (PS106/J928) (Unit of replacement: EDGE STOPPER ASSEMBLY) - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Alignment Guide Motor 1. Saddle Stitcher Controller PCB (UN101/J213) to Relay Connector (17P) (Unit of replacement: CABLE, SADDLE SENSOR, FRONT) 2. Relay Connector (17P) to Relay Connector (17P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (17P) to Saddle Alignment Guide Motor (M102/J923) (Unit of replacement: EDGE STOPPER ASSEMBLY) - Saddle Alignment Plate HP Sensor (PS106) - Saddle Alignment Guide Motor (M102) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Alignment Plate HP Sensor (S206) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Alignment Guide Motor (M202) to the Saddle Stitcher Controller PCB - Saddle Alignment Plate HP Sensor (S206) - Saddle Alignment Guide Motor (M202) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Alignment HP Sensor (PS207) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Alignment Motor (M203) to the Saddle Stitcher Controller PCB - Saddle Alignment HP Sensor (PS207) - Saddle Alignment Motor (M203) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F3-8002-02
Description:	a. Saddle Alignment Plate HP error (Finisher-W1) b. Error in the Saddle Alignment Guide Motor (Finisher-X1) c. Error in the Saddle Alignment Motor (Finisher-V)
Causes:	a. The Saddle Alignment Plate HP Sensor was not turned OFF although 1.5 sec had passed after the Saddle Alignment Guide Motor started the operation. b. The saddle alignment guide does not come off the Saddle Alignment Plate HP Sensor when the Saddle Alignment Guide Motor has been driven for 50 pulses. c. The Saddle Alignment HP Sensor does not detect the saddle alignment plate when the Saddle Alignment Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Alignment Plate HP Sensor 1. Saddle Stitcher Controller PCB (UN101/J213) to Relay Connector (17P) (Unit of replacement: CABLE, SADDLE SENSOR, FRONT) 2. Relay Connector (17P) to Relay Connector (17P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (17P) to Saddle Alignment Plate HP Sensor (PS106/J928) (Unit of replacement: EDGE STOPPER ASSEMBLY) - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Alignment Guide Motor 1. Saddle Stitcher Controller PCB (UN101/J213) to Relay Connector (17P) (Unit of replacement: CABLE, SADDLE SENSOR, FRONT) 2. Relay Connector (17P) to Relay Connector (17P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (17P) to Saddle Alignment Guide Motor (M102/J923) (Unit of replacement: EDGE STOPPER ASSEMBLY) - Saddle Alignment Plate HP Sensor (PS106) - Saddle Alignment Guide Motor (M102) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Alignment Plate HP Sensor (S206) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Alignment Guide Motor (M202) to the Saddle Stitcher Controller PCB - Saddle Alignment Plate HP Sensor (S206) - Saddle Alignment Guide Motor (M202) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Alignment HP Sensor (PS207) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Alignment Motor (M203) to the Saddle Stitcher Controller PCB - Saddle Alignment HP Sensor (PS207) - Saddle Alignment Motor (M203) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F4-8001-02
Description:	a. Saddle Staple (Rear) error (Finisher-W1) b. Error in the Saddle Stitcher Motor (Finisher- X1) c. Error in the Saddle Stitcher Motor (Finisher-V)
Causes:	a. The Saddle Staple HP Sensor was not turned ON although 0.8 sec had passed after the Saddle Staple Unit started the operation. b. The Saddle Stitcher HP Sensor does not detect the saddle stitcher unit when the Saddle Stitcher Motor has been driven for 480 msec. c. The saddle stitcher does not come off the Saddle Stitcher HP Sensor when the Saddle Stitcher Motor has been driven for 1.2 seconds.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Saddle Staple Unit to the Saddle Stitcher Controller PCB 1. Saddle Staple Unit (J904) to Relay Connector (10P) (Unit of replacement: CABLE, SADDLE STOPPER) 2. Relay Connector (10P) to Saddle Stitcher Controller PCB (UN101/J207) (Unit of replacement: CABLE, SADDLE SENSOR, RIGHT) - Saddle Staple Unit (Unit of replacement: SADDLE STAPLER ASSEMBLY) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Stitcher HP Sensor (S223) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Stitcher Motor (M209) to the Saddle Stitcher Controller PCB - Saddle Stitcher HP Sensor (S223) - Saddle Stitcher Motor (M209) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Stitcher HP Sensor (PS215) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Stitcher Motor (M208) to the Saddle Stitcher Controller PCB - Saddle Stitcher HP Sensor (PS215) - Saddle Stitcher Motor (M208) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F4-8002-02
Description:	a. Saddle Staple (Rear) error (Finisher-W1) b. Error in the Saddle Stitcher Motor (Finisher- X1) c. Error in the Saddle Stitcher Motor (Finisher-V)
Causes:	a. The Saddle Staple HP Sensor was not turned OFF although 0.5 sec had passed after the Saddle Staple Unit started the operation. b. The Saddle Stitcher unit does not come off the Saddle Stitcher HP Sensor when the Saddle Stitcher Motor has been driven for 480msec. c. The Saddle Stitcher HP Sensor does not detect the saddle stitcher when the Saddle Stitcher Motor has been driven for 1.2 seconds.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Saddle Staple Unit to the Saddle Stitcher Controller PCB 1. Saddle Staple Unit (J904) to Relay Connector (10P) (Unit of replacement: CABLE, SADDLE STOPPER) 2. Relay Connector (10P) to Saddle Stitcher Controller PCB (UN101/J207) (Unit of replacement: CABLE, SADDLE SENSOR, RIGHT) - Saddle Staple Unit (Unit of replacement: SADDLE STAPLER ASSEMBLY) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Stitcher HP Sensor (S223) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Stitcher Motor (M209) to the Saddle Stitcher Controller PCB - Saddle Stitcher HP Sensor (S223) - Saddle Stitcher Motor (M209) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Stitcher HP Sensor (PS215) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Stitcher Motor (M208) to the Saddle Stitcher Controller PCB - Saddle Stitcher HP Sensor (PS215) - Saddle Stitcher Motor (M208) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F6-8001-02
Description:	a. Saddle Paper Thrust Plate HP error (Finisher-W1) b. Error in the Saddle Paper Push-on Plate Motor (Finisher-X1) c. Error in the Saddle Paper Pushing Plate/Folding Motor (Finisher-V)
Causes:	a. The Saddle Paper Thrust Plate HP Sensor was not turned ON although 0.8 sec had passed after the Saddle Paper Thrust Plate Motor started the operation. b. The Saddle Paper Push-on Plate HP Sensor does not detect the saddle paper push-on plate when the Saddle Paper Push-on Plate Motor has been driven for 500 msec. c. The saddle paper pushing plate does not come off the Saddle Paper Pushing Plate HP Sensor when the Saddle Paper Pushing Plate/Folding Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harness between the Saddle Stitcher Controller PCB (UN101/J209) and the Saddle Paper Thrust Plate HP Sensor (PS108/J937) (Unit of replacement: CABLE, SADDLE SENSOR, RIGHT) - Harnesses from the Saddle Paper Thrust Plate Motor to the Saddle Stitcher Controller PCB 1. Saddle Stitcher Controller PCB (UN101/J206) to Relay Connector (4P) (Unit of replacement: SADDLE ASSEMBLY) 2. Relay Connector (4P) to Relay Connector (4P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (4P) to Saddle Paper Thrust Plate Motor (M105/J901) (Unit of replacement: MOTOR, DC) - Saddle Paper Thrust Plate HP Sensor (PS108) - Saddle Paper Thrust Plate Motor (M105) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Paper Push-on Plate HP Sensor (S218) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper Push-on Plate Motor (M205) to the Saddle Stitcher Controller PCB - Saddle Paper Push-on Plate HP Sensor (S218) - Saddle Paper Push-on Plate Motor (M205) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Paper Pushing Plate HP Sensor (PS208) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper Pushing Plate/Folding Motor (M204) to the Saddle Stitcher Controller PCB - Saddle Paper Pushing Plate HP Sensor (PS208) - Saddle Paper Pushing Plate/Folding Motor (M204) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F6-8002-02
Description:	a. Saddle Paper Thrust Plate HP error (Finisher-W1) b. Error in the Saddle Paper Push-on Plate Motor (Finisher-X1) c. Error in the Saddle Paper Pushing Plate/Folding Motor (Finisher-V)
Causes:	a. The Saddle Paper Thrust Plate HP Sensor was not turned OFF although 0.8 sec had passed after the Saddle Paper Thrust Plate Motor started the operation. b. The saddle paper push-on plate does not come off the Saddle Paper Push-on Plate HP Sensor when the Saddle Paper Push-on Plate Motor has been driven for 150 msec. c. The Saddle Paper Pushing Plate HP Sensor does not detect the saddle paper pushing plate when the Saddle Paper Pushing Plate/Folding Motor has been driven for 3 seconds.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harness between the Saddle Stitcher Controller PCB (UN101/J209) and the Saddle Paper Thrust Plate HP Sensor (PS108/J937) (Unit of replacement: CABLE, SADDLE SENSOR, RIGHT) - Harnesses from the Saddle Paper Thrust Plate Motor to the Saddle Stitcher Controller PCB 1. Saddle Stitcher Controller PCB (UN101/J206) to Relay Connector (4P) (Unit of replacement: SADDLE ASSEMBLY) 2. Relay Connector (4P) to Relay Connector (4P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (4P) to Saddle Paper Thrust Plate Motor (M105/J901) (Unit of replacement: MOTOR, DC) - Saddle Paper Thrust Plate HP Sensor (PS108) - Saddle Paper Thrust Plate Motor (M105) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) - Finisher Controller PCB (UN3) (Unit of replacement: FINISHER CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts> Points to Note when Replacing the Finisher Controller PCB" in the Service Manual for the Finisher. b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Paper Push-on Plate HP Sensor (S218) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper Push-on Plate Motor (M205) to the Saddle Stitcher Controller PCB - Saddle Paper Push-on Plate HP Sensor (S218) - Saddle Paper Push-on Plate Motor (M205) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual. c. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Paper Pushing Plate HP Sensor (PS208) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper Pushing Plate/Folding Motor (M204) to the Saddle Stitcher Controller PCB - Saddle Paper Pushing Plate HP Sensor (PS208) - Saddle Paper Pushing Plate/Folding Motor (M204) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F6-8003-02
Description:	a. Saddle Paper Push-on Plate Motor clock error (Finisher-X1) b. Saddle Paper Pushing Plate/Folding Motor clock error (Finisher-V)
Causes:	a. The drive speed of the Saddle Paper Push-on Plate Motor is less than 6 clocks. b. The lock state of Saddle Paper Pushing Plate/Folding Motor is detected 0.2 seconds or more while the motor operates.
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Paper Push-on Plate Motor Sensor (S213) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper Push-on Plate Motor (M205) to the Saddle Stitcher Controller PCB - Saddle Paper Push-on Plate Motor Sensor (S213) - Saddle Paper Push-on Plate Motor (M205) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Paper Pushing Plate/Folding Motor Clock Sensor (PS212) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper Pushing Plate/Folding Motor (M204) to the Saddle Stitcher Controller PCB - Saddle Paper Pushing Plate/Folding Motor Clock Sensor (PS212) - Saddle Paper Pushing Plate/Folding Motor (M204) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F8-8001-02
Description:	a. Error in the Saddle Tapping Motor (Finisher-X1) b. Error in the Saddle Switching Lever Motor (Finisher-V)
Causes:	a. The Saddle Paper Tapping HP Sensor does not detect the Saddle tapping plate when the Saddle Tapping Motor has been driven for 50 pulses. b. The saddle switching lever does not come off the Saddle Switching Lever HP Sensor when the Saddle Switching Lever Motor has been driven for 1 second.
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Paper Tapping HP Sensor (S215) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Tapping Motor (M213) to the Saddle Stitcher Controller PCB - Saddle Paper Tapping HP Sensor (S215) - Saddle Tapping Motor (M213) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Switching Lever HP Sensor (PS205) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Switching Lever Motor (M202) to the Saddle Stitcher Controller PCB - Saddle Switching Lever HP Sensor (PS205) - Saddle Switching Lever Motor (M202) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5F8-8002-02
Description:	a. Error in the Saddle Tapping Motor (Finisher-X1) b. Error in the Saddle Switching Lever Motor (Finisher-V)
Causes:	a. The saddle tapping plate does not come off the Saddle Paper Tapping HP Sensor when the Saddle Tapping Motor has been driven for 50 pulses. b. The Saddle Switching Lever HP Sensor does not detect the saddle switching lever when the Saddle Switching Lever Motor has been driven for 1 second.
Remedy:	a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Paper Tapping HP Sensor (S215) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Tapping Motor (M213) to the Saddle Stitcher Controller PCB - Saddle Paper Tapping HP Sensor (S215) - Saddle Tapping Motor (M213) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Switching Lever HP Sensor (PS205) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Switching Lever Motor (M202) to the Saddle Stitcher Controller PCB - Saddle Switching Lever HP Sensor (PS205) - Saddle Switching Lever Motor (M202) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5FA-8001-02
Description:	a. Saddle Press Motor error (Finisher-W1) b. Error in the Saddle Gripper Motor (Finisher-V)
Causes:	a. The Saddle Press Motor did not move although 0.2 sec had passed after the motor started the operation. b. The saddle gripper does not come off the Saddle Gripper HP Sensor when the Saddle Gripper Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Press Position Sensor 1. Saddle Stitcher Controller PCB (UN101/J207) to Relay Connector (9P) (Unit of replacement: CABLE, SADDLE SENSOR, RIGHT) 2. Relay Connector (9P) to Relay Connector (9P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (9P) to Saddle Press Position Sensor (PS116/J913) (Unit of replacement: CABLE, PRESS SENSOR) - Saddle Press Motor (M108) - Saddle Press Position Sensor (PS116) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Gripper HP Sensor (PS209) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Gripper Motor (M205) to the Saddle Stitcher Controller PCB - Saddle Gripper HP Sensor (PS209) - Saddle Gripper Motor (M205) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	5FA-8002-02
Description:	a. Saddle press position detection error (Finisher-W1) b. Error in the Saddle Gripper Motor (Finisher-V)
Causes:	a. The Saddle Press Position Sensor was not turned ON although 10 sec had passed after the Saddle Press Motor started the operation. b. The Saddle Gripper HP Sensor does not detect the saddle gripper when the Saddle Gripper Motor has been driven for 1 second.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harnesses from the Saddle Stitcher Controller PCB to the Saddle Press Position Sensor 1. Saddle Stitcher Controller PCB (UN101/J207) to Relay Connector (9P) (Unit of replacement: CABLE, SADDLE SENSOR, RIGHT) 2. Relay Connector (9P) to Relay Connector (9P) (Unit of replacement: SADDLE ASSEMBLY) 3. Relay Connector (9P) to Saddle Press Position Sensor (PS116/J913) (Unit of replacement: CABLE, PRESS SENSOR) - Saddle Press Motor (M108) - Saddle Press Position Sensor (PS116) - Saddle Stitcher Controller PCB (UN101) (Unit of replacement: SADDLE DRIVER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Gripper HP Sensor (PS209) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Gripper Motor (M205) to the Saddle Stitcher Controller PCB - Saddle Gripper HP Sensor (PS209) - Saddle Gripper Motor (M205) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the malfunction in the swing guide unit. 2. Check whether there is not the malfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

Error code:	602-0001-00
Description:	HDD error
Causes:	HDD failed to be Ready, or HDD was not formatted. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Turn ON the main power, and check whether the error is cleared. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 5. After replacing the HDD, format the HDD. 6. Replace the Main Controller PCB.

Error code:	602-0101-00
Description:	HDD error
Causes:	An error was detected in the PDL-related file storage area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0111-00
Description:	HDD error
Causes:	An error was detected in the PDL-related file storage area. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0201-00
Description:	HDD error
Causes:	An error was detected in the storage area of image data after startup. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0211-00
Description:	HDD error
Causes:	An error was detected in the storage area of image data after startup. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0301-00
Description:	HDD error
Causes:	An error was detected in the MEAP-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0311-00
Description:	HDD error
Causes:	An error was detected in the MEAP-related area. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0401-00
Description:	HDD error
Causes:	Logical partition error was detected. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 4. After replacing the HDD, format the HDD. 5. Replace the Main Controller PCB.

Error code:	602-0411-00
Description:	HDD error
Causes:	Logical partition error was detected. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 4. After replacing the HDD, format the HDD. 5. Replace the Main Controller PCB.

Error code:	602-0501-00
Description:	HDD error
Causes:	An error was detected in the storage area of image data after startup. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0511-00
Description:	HDD error
Causes:	An error was detected in the storage area of image data after startup. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0601-00
Description:	HDD error
Causes:	An error was detected in the storage area of image data after startup. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "6", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "6", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0611-00
Description:	HDD error
Causes:	An error was detected in the storage area of image data after startup. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "6", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "6", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0701-00
Description:	HDD error
Causes:	An error was detected in general application temporary area (temporary file). (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "7", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "7", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0711-00
Description:	HDD error
Causes:	An error was detected in general application temporary area (temporary file). (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "7", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "7", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0801-00
Description:	HDD error
Causes:	An error was detected in the general application-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0811-00
Description:	HDD error
Causes:	An error was detected in the general application-related area. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0901-00
Description:	HDD error
Causes:	An error was detected in PDL spool data (temporary file). (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "9", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "9", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-0911-00
Description:	HDD error
Causes:	An error was detected in PDL spool data (temporary file). (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "9", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "9", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1001-00
Description:	HDD error
Causes:	An error was detected in the SEND-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "10", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "10", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1011-00
Description:	HDD error
Causes:	An error was detected in the SEND-related area. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "10", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "10", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1101-00
Description:	HDD error
Causes:	An error was detected in the update-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "11", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "11", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1111-00
Description:	HDD error
Causes:	An error was detected in the update-related area. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "11", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "11", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1201-00
Description:	HDD error
Causes:	An error was detected in the license-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "12", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 5. After replacing the HDD, format the HDD. 6. Replace the Main Controller PCB.

Error code:	602-1211-00
Description:	HDD error
Causes:	An error was detected in the license-related area. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "12", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 5. After replacing the HDD, format the HDD. 6. Replace the Main Controller PCB.

Error code:	602-1301-00
Description:	HDD error
Causes:	An error was detected in the system area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "13", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 5. After replacing the HDD, format the HDD. 6. Replace the Main Controller PCB.

Error code:	602-1311-00
Description:	HDD error
Causes:	An error was detected in the system area. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "13", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 5. After replacing the HDD, format the HDD. 6. Replace the Main Controller PCB.

Error code:	602-1401-00
Description:	HDD error
Causes:	An error was detected in SWAP (temporary file/alternative memory area). (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "14", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 5. After replacing the HDD, format the HDD. 6. Replace the Main Controller PCB.

Error code:	602-1411-00
Description:	HDD error
Causes:	An error was detected in SWAP (temporary file/alternative memory area). (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "14", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 5. After replacing the HDD, format the HDD. 6. Replace the Main Controller PCB.

Error code:	602-1701-00
Description:	HDD error
Causes:	An error was detected in the debug log area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "17", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "17", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1711-00
Description:	HDD error
Causes:	An error was detected in the debug log area. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "17", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "17", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1801-00
Description:	HDD error
Causes:	An error was detected in the image data storage area in Advanced Box. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "18", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "18", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1811-00
Description:	HDD error
Causes:	An error was detected in the image data storage area in Advanced Box. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "18", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "18", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1901-00
Description:	HDD error
Causes:	An error was detected in the storage area of data for printing. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "19", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "19", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-1911-00
Description:	HDD error
Causes:	An error was detected in the storage area of data for printing. (File could not be written in the HDD after startup or I/O error after startup)
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 4 and later. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "19", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "19", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 5. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 6. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 7. After replacing the HDD, format the HDD. 8. Replace the Main Controller PCB.

Error code:	602-2000-00
Description:	SATA-FLASH error
Causes:	Data error in the SATA-FLASH was detected.
Remedy:	After replacing the SATA-FLASH PCB (PWB03) (unit of replacement: SATA-FLASH PCB ASS`Y), reinstall the system software using SST or a USB memory.

Error code:	602-2001-00
Description:	rHDD error
Causes:	Mismatch on encryption board operation
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check that the HDD optional board is properly installed. 2. Turn ON the main power, and check whether the error is cleared. 3. Execute the key clear using SST (to make an unformatted disk). [CAUTION] E602-0001 will be indicated if activating the machine with the unformatted disk. Therefore, be sure to format the HDD. 4. Enter safe mode using (2+8) startup. Then format the HDD and reinstall the system software using SST or a USB flash drive.

Error code:	602-2002-00
Description:	HDD error
Causes:	Failure of encryption board and others
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Turn ON the main power, and check whether the error is cleared. 2. Execute the key clear using SST (to make an unformatted disk). [CAUTION] E602-0001 will be indicated if activating the machine with the unformatted disk. Therefore, be sure to format the HDD. 3. Enter safe mode using (2+8) startup. Then format the HDD and reinstall the system software using SST or a USB flash drive. 4. Replace the Main Controller PCB

Error code:	602-5001-00
Description:	HDD Encryption Board error
Causes:	Mistake in the procedure for installing the HDD Encryption Board
Remedy:	[Related parts] Encryption Board [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Remove the Encryption Board and install the HDD only. Then, turn ON the main power. 2. Execute "COPIER> FUNCTION> INSTALL> HD-CRYP". 3. Install the Encryption Board.

Error code:	602-5002-00
Description:	HDD error
Causes:	A non-genuine HDD was detected
Remedy:	[Related parts] HDD (Unit of replacement: HDD, WD10EURX, WESTEM DIGITAL) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Install a genuine HDD. 2. Enter download mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory device. 3. Reinstall the necessary application software.

Error code:	602-FF01-00
Description:	HDD error
Causes:	An unidentified HDD error was detected at startup. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 4. After replacing the HDD, format the HDD. 5. Replace the Main Controller PCB.

Error code:	602-FF11-00
Description:	HDD error
Causes:	An unidentified HDD error was detected after startup.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003, J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - HDD (Unit of replacement: HARD DISK DRIVE) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y,1) [Remedy] Perform the following in the order while checking whether the error is cleared. [CAUTION] Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Check the cable between the Main Controller PCB and the HDD 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 4. After replacing the HDD, format the HDD. 5. Replace the Main Controller PCB.

Error code:	604-0512-00
Description:	Faulty/insufficient image memory (Main Controller PCB1)
Causes:	No necessary memory at Main Controller PCB 1
Remedy:	Make the Memory capacity at Main Controller PCB 1 as indicated by 0512.

Error code:	604-1024-00
Description:	Faulty/insufficient image memory (Main Controller PCB1)
Causes:	No necessary memory at Main Controller PCB 1
Remedy:	Make the Memory capacity at Main Controller PCB 1 as indicated by 1024

Error code:	604-1536-00
Description:	Faulty/insufficient image memory (Main Controller PCB1)
Causes:	No necessary memory at Main Controller PCB 1
Remedy:	Make the Memory capacity at Main Controller PCB 1 as indicated by 1536.

Error code:	613-0512-00
Description:	Faulty/insufficient image memory
Causes:	No necessary memory at Main Controller PCB
Remedy:	Make the Memory capacity at Main Controller PC as indicated by 0512.

Error code:	613-1024-00
Description:	Faulty/insufficient image memory
Causes:	No necessary memory at Main Controller PCB
Remedy:	Make the Memory capacity at Main Controller PCB as indicated by 1024.

Error code:	613-1536-00
Description:	Faulty/insufficient image memory
Causes:	No necessary memory at Main Controller PCB
Remedy:	Make the Memory capacity at Main Controller PCB as indicated by 1536.

Error code:	614-0001-00
Description:	Flash PCB error
Causes:	The Flash PCB could not be recognized, or the Flash PCB was not formatted.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 4. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 5. Replace the Main Controller PCB.

Error code:	614-0002-00
Description:	Error in file system on the Flash PCB
Causes:	The file system could not be initialized normally at startup. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 4. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 5. Replace the Main Controller PCB.

Error code:	614-0006-00
Description:	Error in file system on the Flash PCB
Causes:	Bootable was not found on the Flash PCB.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 4. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 5. Replace the Main Controller PCB.

Error code:	614-0101-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the system area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0111-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the system area. (File could not be written in the Flash PCB after startup or I/O error after startup)
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0201-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the system area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0211-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the system area. (File could not be written in the Flash PCB after startup or I/O error after startup)
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0301-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the system area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0311-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the system area. (File could not be written in the Flash PCB after startup or I/O error after startup)
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0401-00
Description:	Error in file system on the Flash PCB
Causes:	Logical partition error was detected. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0411-00
Description:	Error in file system on the Flash PCB
Causes:	Logical partition error was detected. (File could not be written in the Flash PCB after startup or I/O error after startup)
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0501-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the general application-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. - When prioritizing clearing of the error, perform Remedy 3 and later. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 6. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 7. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0511-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the general application-related area. (File could not be written in the Flash PCB after startup or I/O error after startup)
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. - When prioritizing clearing of the error, perform Remedy 3 and later. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 6. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 7. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0601-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the license-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0611-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in the license-related area. (File could not be written in the Flash PCB after startup or I/O error after startup)
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Sata Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0701-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in system setting value (service mode, etc.) storage area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. - When prioritizing clearing of the error, perform Remedy 3 and later. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 6. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 7. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-0711-00
Description:	Error in file system on the Flash PCB
Causes:	An error was detected in system setting value (service mode, etc.) storage area. (File could not be written in the Flash PCB after startup or I/O error after startup)
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. - When prioritizing clearing of the error, perform Remedy 3 and later. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 6. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 7. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-4000-00
Description:	Error in file system on the Flash PCB
Causes:	The OS could not be recognized. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - Format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 3. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-4001-00
Description:	Error in file system on the Flash PCB
Causes:	The OS boot file was not found. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - Format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 3. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-4002-00
Description:	Error in file system on the Flash PCB
Causes:	The OS kernel was not found. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - Format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 3. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-4003-00
Description:	Error in file system on the Flash PCB
Causes:	The OS boot loader was not found. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - Format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 3. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-4010-00
Description:	Error in file system on the Flash PCB
Causes:	The OS in safe mode could not be recognized. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Remedy] Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-4011-00
Description:	Error in file system on the Flash PCB
Causes:	The file for booting the OS in safe mode was not found. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-4012-00
Description:	Error in file system on the Flash PCB
Causes:	The kernel in safe mode was not found. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-9000-00
Description:	Error in file system on the Flash PCB
Causes:	SRAM device access-related error (at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - Format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 3. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-9001-00
Description:	Error in file system on the Flash PCB
Causes:	Error in memory allocation/invalid memory (at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - Format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 3. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-9002-00
Description:	Error in file system on the Flash PCB
Causes:	Setting file error was detected at startup. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - Format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 3. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-9003-00
Description:	Error in file system on the Flash PCB
Causes:	Parameter error was detected at startup. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - Format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 3. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-9004-00
Description:	Error in file system on the Flash PCB
Causes:	Startup error was detected. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Disconnect and then connect the connectors of the Sata Flash PCB (PWB3) and the Main Power Switch, and check if there is any bent pin or cable disconnection. - Format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 3. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory.

Error code:	614-FF01-00
Description:	Error in file system on the Flash PCB
Causes:	Flash error (Unidentified) (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	614-FF11-00
Description:	Error in file system on the Flash PCB
Causes:	Flash error (Unidentified) (File could not be written in the Flash PCB after startup or I/O error after startup)
Remedy:	[Related parts] - Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. - Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Sata Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	615-0001-00
Description:	Error in self-diagnosis of the encryption module
Causes:	An error was detected in self-diagnosis of the encryption library.
Remedy:	Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After reinstalling the system software using SST or a USB memory, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 4. After replacing the Flash PCB (UN61), reinstall the system software using SST or a USB memory. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	674-0001-07
Description:	Fax Board communication error
Causes:	An error was detected for the specified number of times in communication with the Fax Board.
Remedy:	[Related parts] - Harness between the Fax Board and the Main Controller PCB 1 (PWB01/J4011) (Unit of replacement: CABLE, SIGNAL) - Fax Board - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY, 1) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	674-0002-07
Description:	Fax Board communication error
Causes:	An error was detected for the specified number of times in communication with the Fax Board.
Remedy:	[Related parts] - Harness between the Fax Board and the Main Controller PCB 1 (PWB01/J4011) (Unit of replacement: CABLE, SIGNAL) - Fax Board - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY, 1) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	674-0004-07
Description:	Fax Board communication error
Causes:	A communication error occurred when accessing the modem IC used for fax.
Remedy:	[Related parts] - Harness between the Fax Board and the Main Controller PCB 1 (PWB01/J4011) (Unit of replacement: CABLE, SIGNAL) - Fax Board - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY, 1) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	674-0008-07
Description:	Fax Board communication error
Causes:	A communication error occurred when accessing the port IC used for fax.
Remedy:	[Related parts] - Harness between the Fax Board and the Main Controller PCB 1 (PWB01/J4011) (Unit of replacement: CABLE, SIGNAL) - Fax Board - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY, 1) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	674-0010-07
Description:	Fax Board communication error
Causes:	A communication error occurred when opening the Timer Device used for fax.
Remedy:	Replace the Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY, 1)

Error code:	674-0011-07
Description:	Fax Board communication error
Causes:	A communication error occurred when starting the Timer Device used for fax.
Remedy:	Replace the Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY, 1)

Error code:	674-0020-07
Description:	Fax Board communication error
Causes:	An error occurred in the modem IC used for fax.
Remedy:	[Related parts] - Harness between the Fax Board and the Main Controller PCB 1 (PWB01/J4011) (Unit of replacement: CABLE, SIGNAL) - Fax Board - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY, 1) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	674-0030-07
Description:	Fax Board communication error
Causes:	Check sum error
Remedy:	System software download for 2 line FAX

Error code:	674-0100-07
Description:	Fax Board communication error
Causes:	After completion of fax communication, writing of the communication information (log) failed, and the log could not be read.
Remedy:	Turn OFF and then ON the main power. [CAUTION] The previous communication information (log) will be cleared by turning OFF and then ON the main power.

Error code:	674-0300-07
Description:	Fax configuration error
Causes:	It was detected that there was a Fax Board for multiple lines installed while the IP Fax license was enabled.
Remedy:	- Remove the Fax Board for multiple lines to use the machine as an IP Fax model. - Uninstall the IP Fax license to use the machine as a G3 Fax model.

Error code:	674-0301-07
Description:	Fax configuration error
Causes:	It was detected that there was no 1-line Fax Board installed while the IP Fax license was enabled.
Remedy:	- Install the Fax Board (1-line) to use the machine as an IP Fax model. - Uninstall the IP Fax license and install the G3 Fax Board to use the machine as a G3 Fax model.

Error code:	677-0001-00
Description:	Print server error
Causes:	Exhaust Fan operation error on the print server is detected.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check power supply to the Exhaust Fan. 2. Replace the Exhaust Fan.

Error code:	677-0003-00
Description:	Print server error
Causes:	Error was detected at the configuration check performed at startup.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check the connection cable between the host machine and the print server. 2. Reinstall the system of the print server.

Error code:	677-0004-00
Description:	Print server error
Causes:	CPU Fan operation error on the print server is detected.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check power supply to the CPU Fan. 2. Replace the CPU Fan.

Error code:	677-0010-00
Description:	Print server error
Causes:	Not proper print server is connected.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Replace the print server with the proper one. 2. Reinstall the system of the print server.

Error code:	677-0080-00
Description:	Print server error
Causes:	A communication error between the print server and the host machine was detected.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check the connection cable between the host machine and the print server. 2. Reinstall the system of the print server.

Error code:	713-0010-05
Description:	Finisher communication error (time out error)
Causes:	Timeout was detected in communication between the host machine and the finisher.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harness between the DC Controller PCB (UN01/J1 and J7) and the CAN Transceiver (J3 and J4) (Unit of replacement: CABLE, INTERFACE, CAN) - Harness between the Finisher Controller PCB and the CAN Transceiver - CAN Transceiver Cable - CAN Transceiver PCB (Unit of replacement: TRANSCEIVER PCB ASSEMBLY, CAN) - Finisher Controller PCB - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the DC Controller PCB/Relay PCB to the Finisher Lattice Connector 1. DC Controller PCB (UN01/J462) to Relay Connector (9P) (Unit of replacement: CABLE, SIGNAL) 2. Relay PCB (UN86/J505) to Relay Connector (4P) (Unit of replacement: CABLE, SIGNAL) 3. Relay Connector (9P and 4P) to Finisher Lattice Connector (J9043) (Unit of replacement: CABLE, FINISHER CONNECTOR) - Finisher Controller PCB - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES - After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual for the Finisher.

Error code:	713-0011-05
Description:	Finisher communication error (NACK reception error)
Causes:	Finisher communication error (NACK reception error) Detection Description Retransmission of NACK was detected consecutively in communication between the host machine and the finisher.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harness between the DC Controller PCB (UN01/J1 and J7) and the CAN Transceiver (J3 and J4) (Unit of replacement: CABLE, INTERFACE, CAN) - Harness between the Finisher Controller PCB and the CAN Transceiver - CAN Transceiver Cable - CAN Transceiver PCB (Unit of replacement: TRANSCEIVER PCB ASSEMBLY, CAN) - Finisher Controller PCB - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the DC Controller PCB/Relay PCB to the Finisher Lattice Connector 1. DC Controller PCB (UN01/J462) to Relay Connector (9P) (Unit of replacement: CABLE, SIGNAL) 2. Relay PCB (UN86/J505) to Relay Connector (4P) (Unit of replacement: CABLE, SIGNAL) 3. Relay Connector (9P and 4P) to Finisher Lattice Connector (J9043) (Unit of replacement: CABLE, FINISHER CONNECTOR) - Finisher Controller PCB - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES - After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual for the Finisher.

Error code:	713-0020-05
Description:	Finisher communication error (invalid BCC in received data)
Causes:	Invalid BCC in received data was detected in communication between the host machine and the finisher.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harness between the DC Controller PCB (UN01/J1 and J7) and the CAN Transceiver (J3 and J4) (Unit of replacement: CABLE, INTERFACE, CAN) - Harness between the Finisher Controller PCB and the CAN Transceiver - CAN Transceiver Cable - CAN Transceiver PCB (Unit of replacement: TRANSCEIVER PCB ASSEMBLY, CAN) - Finisher Controller PCB - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the DC Controller PCB/Relay PCB to the Finisher Lattice Connector 1. DC Controller PCB (UN01/J462) to Relay Connector (9P) (Unit of replacement: CABLE, SIGNAL) 2. Relay PCB (UN86/J505) to Relay Connector (4P) (Unit of replacement: CABLE, SIGNAL) 3. Relay Connector (9P and 4P) to Finisher Lattice Connector (J9043) (Unit of replacement: CABLE, FINISHER CONNECTOR) - Finisher Controller PCB - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES - After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual for the Finisher.

Error code:	713-0021-05
Description:	Finisher communication error (reception timeout error)
Causes:	Reception incomplete was detected consecutively in communication between the host machine and the finisher.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harness between the DC Controller PCB (UN01/J1 and J7) and the CAN Transceiver (J3 and J4) (Unit of replacement: CABLE, INTERFACE, CAN) - Harness between the Finisher Controller PCB and the CAN Transceiver - CAN Transceiver Cable - CAN Transceiver PCB (Unit of replacement: TRANSCEIVER PCB ASSEMBLY, CAN) - Finisher Controller PCB - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the DC Controller PCB/Relay PCB to the Finisher Lattice Connector 1. DC Controller PCB (UN01/J462) to Relay Connector (9P) (Unit of replacement: CABLE, SIGNAL) 2. Relay PCB (UN86/J505) to Relay Connector (4P) (Unit of replacement: CABLE, SIGNAL) 3. Relay Connector (9P and 4P) to Finisher Lattice Connector (J9043) (Unit of replacement: CABLE, FINISHER CONNECTOR) - Finisher Controller PCB - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES - After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual for the Finisher.

Error code:	713-0022-05
Description:	Finisher communication error (undefined error)
Causes:	An undefined error was detected consecutively in communication between the host machine and the finisher.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harness between the DC Controller PCB (UN01/J1 and J7) and the CAN Transceiver (J3 and J4) (Unit of replacement: CABLE, INTERFACE, CAN) - Harness between the Finisher Controller PCB and the CAN Transceiver - CAN Transceiver Cable - CAN Transceiver PCB (Unit of replacement: TRANSCEIVER PCB ASSEMBLY, CAN) - Finisher Controller PCB - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the DC Controller PCB/Relay PCB to the Finisher Lattice Connector 1. DC Controller PCB (UN01/J462) to Relay Connector (9P) (Unit of replacement: CABLE, SIGNAL) 2. Relay PCB (UN86/J505) to Relay Connector (4P) (Unit of replacement: CABLE, SIGNAL) 3. Relay Connector (9P and 4P) to Finisher Lattice Connector (J9043) (Unit of replacement: CABLE, FINISHER CONNECTOR) - Finisher Controller PCB - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES - After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual for the Finisher.

Error code:	713-0030-05
Description:	Finisher communication error (initialization error)
Causes:	An initialization error was detected in communication between the host machine and the finisher.
Remedy:	a. FIN-W1/SADDLE FIN-W1 [Related parts] - Harness between the DC Controller PCB (UN01/J1 and J7) and the CAN Transceiver (J3 and J4) (Unit of replacement: CABLE, INTERFACE, CAN) - Harness between the Finisher Controller PCB and the CAN Transceiver - CAN Transceiver Cable - CAN Transceiver PCB (Unit of replacement: TRANSCEIVER PCB ASSEMBLY, CAN) - Finisher Controller PCB - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) b. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the DC Controller PCB/Relay PCB to the Finisher Lattice Connector 1. DC Controller PCB (UN01/J462) to Relay Connector (9P) (Unit of replacement: CABLE, SIGNAL) 2. Relay PCB (UN86/J505) to Relay Connector (4P) (Unit of replacement: CABLE, SIGNAL) 3. Relay Connector (9P and 4P) to Finisher Lattice Connector (J9043) (Unit of replacement: CABLE, FINISHER CONNECTOR) - Finisher Controller PCB - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES - After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual for the Finisher.

Error code:	719-0001-00
Description:	Coin vendor error
Causes:	The coin vendor which was connected before turning OFF the main power was not connected at power-on.
Remedy:	Check/replace the cable between the charging management equipment and the host machine. [Reference] When operating the machine without the charging management equipment, execute "COPIER> FUNCTION> CLEAR> ERR". (It is designed to generate an error to prevent the misuse by removing the charging management equipment.)

Error code:	719-0002-00
Description:	Coin vendor error
Causes:	IPC error when the coin vendor is running - Open circuit of the IPC, or IPC communication could not be recovered. - Open circuit of the pickup/delivery signal cable was detected. - Invalid connection was detected.
Remedy:	Check/replace the cable between the charging management equipment and the host machine. [Reference] When operating the machine without the charging management equipment, execute "COPIER> FUNCTION> CLEAR> ERR". (It is designed to generate an error to prevent the misuse by removing the charging management equipment.)

Error code:	719-0003-00
Description:	Coin vendor error
Causes:	A communication error with the coin vendor was detected during unit price acquisition at startup.
Remedy:	Check/replace the cable between the charging management equipment and the host machine. [Reference] When operating the machine without the charging management equipment, execute "COPIER> FUNCTION> CLEAR> ERR". (It is designed to generate an error to prevent the misuse by removing the charging management equipment.)

Error code:	719-0004-00
Description:	Coin vendor error
Causes:	The coin vendor was connected to a model that does not support the coin vendor
Remedy:	1. Disconnect the coin vendor

Error code:	719-0031-00
Description:	Card Reader communication error
Causes:	Communication with the Card Reader could not be established at startup.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness between the Card Reader and the Main Controller PCB (PWB1/ J4023 (white connector at the upper side). 2. Replace the Card Reader. [Reference] In the case of operating the device without the Card Reader which had been used, execute "COPIER> FUNCTION> CLEAR> CARD" after removing the Card Reader.

Error code:	719-0032-00
Description:	Card Reader communication error
Causes:	Although communication with the Card Reader was available at startup, it became unavailable in the middle of it.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness between the Card Reader and the Main Controller PCB (PWB1/ J4023 (white connector at the upper side). 2. Replace the Card Reader. [Reference] In the case of operating the device without the Card Reader which had been used, execute "COPIER> FUNCTION> CLEAR> CARD" after removing the Card Reader.

Error code:	720-0001-00
Description:	Error due to non-compatible Finisher
Causes:	Non-compatible Finisher was connected.
Remedy:	Connect either the Staple Finisher-Y1 or Saddle Stitch Finisher-Y1.

Error code:	730-C001-00
Description:	Error in HDD access
Causes:	An error occurred when accessing the HDD.
Remedy:	[Related parts] R1.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Format the HDD and reinstall the system software using SST or a USB flash drive. 2. Check/replace the related harness/cable, connector and parts.

Error code:	731-3000-00
Description:	Main Controller PCB error
Causes:	Unable to recognize the SURF Board.
Remedy:	Check/replace the Main Controller PCB

Error code:	731-3001-00
Description:	Main Controller PCB error
Causes:	Failure of SURF initialization.
Remedy:	Check/replace the Main Controller PCB

Error code:	731-3002-00
Description:	Main Controller PCB error
Causes:	Failure of SURF initialization.
Remedy:	Check/replace the Main Controller PCB

Error code:	731-3015-00
Description:	Main Controller PCB error
Causes:	Video data is not transmitted to CL1-G even though there is no problem in the software.
Remedy:	Check/replace the Main Controller PCB

Error code:	732-0001-00
Description:	Communication error
Causes:	A communication error between the Reader Controller PCB and the Main Controller PCB was detected.
Remedy:	[Related parts] R1.00 - Harness between the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Reader Controller PCB (UN_BO1) - Riser PCB - Main Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	732-0010-00
Description:	Scanner communication error
Causes:	A signal to start image transfer could not be detected at scanning although the specified period of time (120 sec) has passed.
Remedy:	[Related parts] - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) - Main Controller PCB 2 (PWB02) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 2) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) [Points to note at work] After performing the remedy, check that the copy image is output normally. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Reinstall the latest system software using SST or a USB memory. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	732-0020-00
Description:	Communication error
Causes:	A communication error between the Reader Controller PCB and the Main Controller PCB was detected
Remedy:	[Related parts] R1.00 - Harness between the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Reader Controller PCB (UN_BO1) - Riser PCB - Main Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	732-0021-00
Description:	Communication error
Causes:	A communication error between the Reader Controller PCB and the Main Controller PCB was detected.
Remedy:	[Related parts] R1.00 - Harness between the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Reader Controller PCB (UN_BO1) - Riser PCB - Main Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	732-0022-00
Description:	Communication error
Causes:	A communication error between the Reader Controller PCB and the Main Controller PCB was detected.
Remedy:	[Related parts] R1.00 - Harness between the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Reader Controller PCB (UN_BO1) - Riser PCB - Main Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	732-0023-04
Description:	Communication error
Causes:	A communication error between the Reader Controller PCB and the Main Controller PCB 1was detected at startup/recovery from sleep.
Remedy:	[Related parts] - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) - Harnesses from the Relay PCB to the Reader Controller PCB 1. Relay PCB (UN7/J505) to Relay Connector (6P) (Unit of replacement: CABLE, SIGNAL) 2. Relay Connector (6P) to Reader Controller PCB (PCB1/J101) (Unit of replacement: CABLE, READER POWER SUPPLY) - Main Controller PCB 2 (PWB02) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 2) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY, 1) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) - Relay PCB (UN7) (Unit of replacement: RELAY PCB ASSEMBLY) [Points to note at work] After performing the remedy, check that the copy image is output normally. [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	732-0F01-04
Description:	Communication error
Causes:	Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0001 is generated.
Remedy:	It is not necessary to perform a remedy because the machine is automatically rebooted after log collection.

Error code:	732-0F20-00
Description:	Communication error
Causes:	Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0020 is generated.
Remedy:	It is not necessary to perform a remedy because the machine is automatically rebooted after log collection.

Error code:	732-0F21-00
Description:	Communication error
Causes:	Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0021 is generated.
Remedy:	It is not necessary to perform a remedy because the machine is automatically rebooted after log collection.

Error code:	732-0F22-00
Description:	Communication error
Causes:	Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0022 is generated.
Remedy:	It is not necessary to perform a remedy because the machine is automatically rebooted after log collection.

Error code:	732-0F23-04
Description:	Communication error
Causes:	Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0023 is generated.
Remedy:	It is not necessary to perform a remedy because the machine is automatically rebooted after log collection.

Error code:	732-8888-00
Description:	Error in the reader type
Causes:	When a scanner for the different model is detected during the communication with the reader.
Remedy:	Replace to the proper reader.

Error code:	733-0000-05
Description:	Printer communication error
Causes:	A communication error between the DC Controller PCB and the Main Controller PCB was detected at startup.
Remedy:	[Related parts] - Harness between the Main Controller PCB 2 (PWB02/J5201) and the DC Controller PCB (UN01/ J443) (Unit of replacement: CABLE, COMMUNICATION) - Harness between the Main Controller PCB 2 (PWB02/J5202) and the DC Controller PCB (UN01/ J442) (Unit of replacement: CABLE, SIGNAL) - Connector between the Main Controller PCB 1 (PWB01) and the Main Controller PCB 2 (PWB02) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) - Main Controller PCB 2 (PWB02) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 2) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	733-0001-05
Description:	Printer communication error
Causes:	A communication error between the DC Controller PCB and the Main Controller PCB was detected.
Remedy:	[Related parts] - Harness between the Main Controller PCB 2 (PWB02/J5201) and the DC Controller PCB (UN01/ J443) (Unit of replacement: CABLE, COMMUNICATION) - Harness between the Main Controller PCB 2 (PWB02/J5202) and the DC Controller PCB (UN01/ J442) (Unit of replacement: CABLE, SIGNAL) - Connector between the Main Controller PCB 1 (PWB01) and the Main Controller PCB 2 (PWB02) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) - Main Controller PCB 2 (PWB02) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 2) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	733-0002-05
Description:	Printer communication error
Causes:	A communication error between the DC Controller PCB and the Main Controller PCB was detected.
Remedy:	[Related parts] - Harness between the Main Controller PCB 2 (PWB02/J5201) and the DC Controller PCB (UN01/ J443) (Unit of replacement: CABLE, COMMUNICATION) - Harness between the Main Controller PCB 2 (PWB02/J5202) and the DC Controller PCB (UN01/ J442) (Unit of replacement: CABLE, SIGNAL) - Connector between the Main Controller PCB 1 (PWB01) and the Main Controller PCB 2 (PWB02) - DC Controller PCB (UN01) (Unit of replacement: DC CONTROLLER PCB ASS`Y) - Main Controller PCB 2 (PWB02) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 2) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	733-0F00-05
Description:	Printer communication error
Causes:	Communication error that can be recovered by reboot If it is detected again immediately after reboot, E733-0000 is generated.
Remedy:	It is not necessary to perform a remedy because the machine is automatically rebooted after log collection.

Error code:	733-0F01-05
Description:	Printer communication error
Causes:	Communication error that can be recovered by reboot If it is detected again immediately after reboot, E733-0001 is generated.
Remedy:	It is not necessary to perform a remedy because the machine is automatically rebooted after log collection.

Error code:	733-0F02-05
Description:	Printer communication error
Causes:	Communication error that can be recovered by reboot If it is detected again immediately after reboot, E733-0002 is generated.
Remedy:	It is not necessary to perform a remedy because the machine is automatically rebooted after log collection.

Error code:	733-9999-05
Description:	Printer communication error
Causes:	The Finisher connection information differs between the Riser PCB and the DC Controller PCB.
Remedy:	Turn OFF and then ON the power

Error code:	743-0000-04
Description:	Communication error
Causes:	The Reader Controller PCB detected a communication error between the Main Controller PCB 1 and the Reader Controller PCB.
Remedy:	[Related parts] - Harness between the Reader Controller PCB (UN1/J109) and the Main Controller PCB 2 (PWB02/J4031) (Unit of replacement: CABLE, INTERFACE) - Reader Controller PCB (UN1) (Unit of replacement: READER CONTROLLER PCB ASSEMBLY) - Main Controller PCB 2 (PWB02) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 2) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY, 1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES

Error code:	743-0001-04
Description:	DDI communication error
Causes:	Software sequence error
Remedy:	Turn OFF and then ON the main power.

Error code:	744-0001-00
Description:	Language file error
Causes:	The language file in the HDD was not supported by the version of Bootable.
Remedy:	Reinstall the correct language file or system software using SST or a USB memory.

Error code:	744-0002-00
Description:	Language file error
Causes:	Size of the language file in HDD was too big.
Remedy:	Reinstall the correct language file using SST or USB memory reinstall the entire software.

Error code:	744-0003-00
Description:	Language file error
Causes:	The language file to be switched to that was described in the Config.txt in HDD was not found.
Remedy:	Reinstall the correct language file using SST or USB memory reinstall the entire software.

Error code:	744-0004-00
Description:	Language file error
Causes:	Switching to the language file in the HDD failed.
Remedy:	Reinstall the correct language file using SST or USB memory reinstall the entire software.

Error code:	744-2000-00
Description:	Controller firmware mismatch
Causes:	Invalid controller firmware was detected.
Remedy:	This error normally does not occur. This error occurs when using the HDD which was used with another model. Replace the HDD with the one which was originally installed or a new one for the model.

Error code:	744-5000-07
Description:	Mismatch of software version for fax
Causes:	After the Fax Board (option) has been installed, mismatch of version of software in the Fax Board was detected at transmission and reception.
Remedy:	Upgrade the system software version to the latest one.

Error code:	746-0011-00
Description:	Voice Board error
Causes:	Because both the voice composition board and the composition recognition board are inserted.
Remedy:	Insert only 1 board of the appropriate voice board.

Error code:	746-0021-00
Description:	Image Analysis Board error
Causes:	Self-check NG of Image Analysis Board
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check that the Image Analysis Board is installed properly by removing and then installing it again. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. After replacing the Image Analysis Board, reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB memory.

Error code:	746-0022-00
Description:	Image Analysis Board error
Causes:	Wrong version of the Image Analysis Board was detected.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB memory. 2. After replacing the Image Analysis Board, perform step 1.

Error code:	746-0023-00
Description:	Image Analysis Board error
Causes:	Communication from the Image Analysis Board could not be detected.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check that the Image Analysis Board is installed properly by removing and then installing it again. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. After replacing the Image Analysis Board, reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB memory.

Error code:	746-0024-00
Description:	Image Analysis Board error
Causes:	An error in the operation of the Image Analysis Board was detected.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Check that the Image Analysis Board is installed properly by removing and then installing it again. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. After replacing the Image Analysis Board, reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB memory.

Error code:	746-0031-00
Description:	TPM error
Causes:	A communication error between the Main Controller PCB and the TPM PCB was detected at startup.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. After turning OFF the main power, replace the TPM PCB. (Unit of replacement: TPM PCB ASSEMBLY) 3. If the TPM key was backed up, restore the key. 3-1. Connect the USB memory which stores the TPM key. 3-2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 3-3. Enter the password set at backup operation. 3-4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power.

Error code:	746-0032-00
Description:	TPM error
Causes:	Mismatch of the TPM key was detected.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Format the system. 1-1. Enter safe mode using (2+8) startup, and execute [4]: Clear/Format> [2]: Flash Format (Flash format) using a USB memory. 1-2. Reinstall the system software using SST or a USB memory. 2. Replace the TPM PCB. (Unit of replacement: TPM PCB ASSEMBLY) 3. If the TPM key was backed up, restore the key. 3-1. Connect the USB memory which stores the TPM key. 3-2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 3-3. Enter the password set at backup operation. 3-4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power.

Error code:	746-0033-00
Description:	TPM error
Causes:	It was detected that data in TPM was inconsistent.
Remedy:	Perform the following in the order while checking whether the error is cleared. Perform the appropriate remedy according to the status whether the TPM key was backed up. a. If the TPM key was backed up, restore the key. 1. Connect the USB memory which stores the TPM key. 2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 3. Enter the password set at backup operation. 4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power. b. If the TPM key was not backed up, format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory.

Error code:	746-0034-00
Description:	TPM auto-recovery error
Causes:	The error occurred when clearing HDD while TPM setting was ON.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. a. If the error is cleared, execute "Settings/Registration> Log In> Management Settings> Data Management> Initialize All Data/Settings". b. If the error is not cleared, format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 2. If the TPM key was backed up, restore the key. 2-1. Connect the USB memory which stores the TPM key. 2-2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 2-3. Enter the password set at backup operation. 2-4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power.

Error code:	746-0035-00
Description:	TPM version error
Causes:	TPM PCB which cannot be used in this machine was installed.
Remedy:	Install the TPM PCB for this model. (Unit of replacement: TPM PCB ASSEMBLY)

Error code:	747-0000-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-001E-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0119-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-011A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-011B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0219-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-021A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-021B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0319-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-031A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-031B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0419-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-041A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-041B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-051B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-051C-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-051D-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0618-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0619-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-061A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts

Error code:	747-061B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0718-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0719-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-071A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-071B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0818-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0819-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-081A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-081B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0918-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0919-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-091A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-091B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0A18-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0A19-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0A1A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	- Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0A1B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0B18-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0B19-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0B1A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0B1B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0C18-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0C19-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0C1A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-0C1B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-110D-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-110E-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1117-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1200-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1201-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1202-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1203-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1204-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1205-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1206-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1207-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts. 7. Error/Jam/Alarm

Error code:	747-1208-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-1217-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-2000-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-2017-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-2018-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-201B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-201C-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-201F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-2217-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-2218-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-221B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-221C-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-221F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-3C00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-3D00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-3F00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6000-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-620C-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-620D-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-620E-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-620F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6210-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6211-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6218-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6219-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-621A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-621B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-621C-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-621D-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-621F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-650F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6513-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6514-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6515-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6516-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6517-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6519-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-651A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-651B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-651C-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-651D-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-651F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6A1F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6B1F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6C1E-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6C1F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-6F1F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-711F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-721F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-741E-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-741F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-751B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-751C-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-751F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-7C00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-7D00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-7F00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-850F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-8513-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-8514-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-8515-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-8516-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-8517-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-8519-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-851A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-851B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-851C-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-851D-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-851F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-951A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-951B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-9C00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-9F00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-C000-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-C519-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-C51A-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-C51B-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-C51C-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-C51D-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-C51F-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-C701-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-C706-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-DC00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-DF00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-FF00-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	747-FF01-00
Description:	Board error
Causes:	There was unexpected interruption from ASIC.
Remedy:	[Related parts] R1.00 - Harness betweens the Reader Controller PCB (UN_BO1/J109) and the Riser PCB (J7) - Bypass PCB (when non-Canon-made controller is installed) - Open I/F PCB (when non-Canon-made controller is installed) - Riser PCB - Main Controller PCB - HDD [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	748-2000-00
Description:	Main Controller PCB access error
Causes:	Main Controller PCB Chip access error.
Remedy:	Replace the Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1)

Error code:	748-2001-00
Description:	Main Controller PCB access error
Causes:	Main Controller PCB memory access error.
Remedy:	Replace the Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1)

Error code:	748-2010-00
Description:	Flash PCB error / HDD error
Causes:	IPL (startup program) was not found, or the HDD could not be recognized.
Remedy:	[Related parts] - Cable between the Main Controller PCB 1 (PWB01/J6003,J6004) and the HDD (Unit of replacement: CABLE, HARD DISK DRIVE, 1) - SATA-FLASH PCB (PWB03) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Disconnect the cable between the Main Controller PCB and the HDD, and turn ON the main power. a. When the error code has not been changed: 1. Obtain the necessary backup data by referring to the backup data list. 2. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 3. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 4. Restore the backup data. b. When the error code has been changed to another one, see the remedy for the corresponding code. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

Error code:	748-2011-00
Description:	Flash PCB error
Causes:	OS is not found
Remedy:	After replacing the SATA-FLASH PCB (PWB03) (unit of replacement: SATA-FLASH PCB ASS`Y), reinstall the system software using SST or a USB memory.

Error code:	748-2012-00
Description:	Flash PCB error
Causes:	Cannot mount the OS in safe mode startup or No OS startup script
Remedy:	After replacing the SATA-FLASH PCB (PWB03) (unit of replacement: SATA-FLASH PCB ASS`Y), reinstall the system software using SST or a USB memory.

Error code:	748-2021-00
Description:	Main Controller PCB access error
Causes:	Main controller board 2 access errors
Remedy:	Replace the Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1)

Error code:	748-2023-00
Description:	Main Controller PCB access error
Causes:	Main controller board 2 access errors
Remedy:	Replace the Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1)

Error code:	748-2024-00
Description:	Main Controller PCB access error
Causes:	Main controller board 2 access errors
Remedy:	Replace the Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1)

Error code:	748-2025-00
Description:	Main Controller PCB access error
Causes:	Main controller board access errors
Remedy:	[Related parts] R1.00 - Bypass PCB - Main Controller PCB [Remedy] Check/replace the related connector and parts.

Error code:	748-2026-00
Description:	Main Controller PCB access error
Causes:	Main controller board access errors
Remedy:	Check/replace the Main Controller PCB

Error code:	748-4910-00
Description:	Main Controller PCB access error
Causes:	Main controller board 2 access errors
Remedy:	Replace the Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1)

Error code:	748-9000-00
Description:	System error
Causes:	System error
Remedy:	Contact to the sales company.

Error code:	749-0006-00
Description:	Error due to change in hardware configuration
Causes:	Change in option configuration could not be detected.
Remedy:	[Remedy] Turn OFF and then ON the main power. [Reference] Options are recognized again by turning OFF and then ON the main power. In the case of changing option configuration, disconnect the power plug or turn OFF the breaker after turning OFF the main power so that an error does not occur.

Error code:	753-0001-00
Description:	Download error
Causes:	Update of the Main Controller PCB ended in failure.
Remedy:	Perform the following in the order while checking whether the error is cleared. 1. Reinstall the system software using SST or a USB memory. 2. After replacing the Sata Flash PCB (PWB3) (Unit of replacement: SATA-FLASH PCB ASS`Y), reinstall the system software using SST or a USB memory. 3. Collect debug log and contact to the sales company.

Error code:	760-0001-00
Description:	Main Controller PCB internal error
Causes:	An error was detected in the Main Controller PCB.
Remedy:	Check/replace the Main Controller PCB (UN158)

Error code:	804-0000-00
Description:	Power Supply Cooling Fan error
Causes:	It was detected that the Power Supply Cooling Fan was locked.
Remedy:	[Related parts] - Harnesses from the Relay PCB to the Power Supply Cooling Fan 1 1. Relay PCB (UN86/J509) to Relay Connector (3P) (Unit of replacement: CABLE, POWER FAN) 2. Relay Connector (3P) to Power Supply Cooling Fan 1 (FM14/J2134) (Unit of replacement: CABLE, POWER FAN) - Harness between the Relay PCB (UN86/J509) and the Power Supply Cooling Fan 2 (FM15/ J2154) (Unit of replacement: CABLE, POWER FAN) - Power Supply Cooling Fan 1 (FM14) - Power Supply Cooling Fan 2 (FM15) - Relay PCB (UN86) (Unit of replacement: RELAY PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	805-0000-05
Description:	Fixing Heat Exhaust Fan Error
Causes:	Rotation error of the Fixing Heat Exhaust Fan 1 was detected. - Rotation signal was detected while the fan was being stopped, or the signal was not detected during operation.
Remedy:	[Related parts] R1.01 - Harness between the Feed/Drum Driver PCB (UN2/J217) and the Fixing Heat Exhaust Fan 1 (FM1/J6066) - Fixing Heat Exhaust Fan 1 (FM1) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	805-0001-05
Description:	Fixing Heat Exhaust Fan Error
Causes:	Rotation error of the Fixing Heat Exhaust Fan 2 was detected. - Rotation signal was detected while the fan was being stopped, or the signal was not detected during operation.
Remedy:	[Related parts] R1.01 - Harness between the Feed/Drum Driver PCB (UN2/J217) and the Fixing Heat Exhaust Fan 2 (FM2/J6067) - Fixing Heat Exhaust Fan 2 (FM2) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	806-0000-05
Description:	Making Image Exhaust Fan error
Causes:	It was detected that the Making Image Exhaust Fan was locked.
Remedy:	[Related parts] - Harnesses from the Feed Driver PCB to the Making Image Exhaust Fan 1. Feed Driver PCB (UN79/J225) to Relay Connector (3P) (Unit of replacement: CABLE, CASSETTE, 3 , 4) 2. Relay Connector (3P) to Making Image Exhaust Fan (FM03/J2088) (Unit of replacement: CABLE, FAN) - Making Image Exhaust Fan (FM03) (Unit of replacement: FAN UNIT) - Feed Driver PCB (UN79) (Unit of replacement: FEED DRIVER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	806-0001-05
Description:	Delivery fan Error
Causes:	Rotation error of the Delivery Fan 2 was detected. - Rotation signal was detected while the fan was being stopped, or the signal was not detected during operation.
Remedy:	[Related parts] R1.00 - Harness between the Front Driver PCB (UN3/J301) and the Delivery Fan 2 (FM9/J3012) - Delivery Fan 2 (FM9) - Front Driver PCB (UN3) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	806-0002-05
Description:	Secondary Transfer Exhaust Fan Error
Causes:	Rotation error of the Secondary Transfer Exhaust Fan was detected. - Rotation signal was detected while the fan was being stopped, or the signal was not detected during operation.
Remedy:	[Related parts] R1.00 - Harness between the Feed/Drum Driver PCB (UN2/J213) and the Secondary Transfer Exhaust Fan (FM8/J6071) - Secondary Transfer Exhaust Fan (FM8) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	807-0000-05
Description:	Process cartridge fan Error
Causes:	Rotation error of the Process Cartridge Fan (Rear) was detected. - Rotation signal was detected while the fan was being stopped, or the signal was not detected during operation.
Remedy:	[Related parts] R1.00 - Harness between the Feed/Drum Driver PCB (UN2/J224) and the Process Cartridge Fan (Rear) (FM4/J6124) - Process Cartridge Fan (Rear) (FM4) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts

Error code:	807-0001-05
Description:	Process cartridge fan Error
Causes:	Rotation error of the Process Cartridge Fan (Front) was detected. - Rotation signal was detected while the fan was being stopped, or the signal was not detected during operation.
Remedy:	[Related parts] R1.00 - Harness between the Feed/Drum Driver PCB (UN2/J224) and the Process Cartridge Fan (Front) (FM10/J6123) - Process Cartridge Fan (Front) (FM10) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	808-0000-05
Description:	Zero Cross Error
Causes:	Zero cross signal was not detected after fixing relay was ON.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J173) and the AC Driver PCB (UN6/J505) - AC Driver PCB (UN6) - DC Controller PCB (UN1) [Remedy] - Check the voltage of the outlet, and connect the machine to the correct outlet if it is wrong. - Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Error code:	840-0000-05
Description:	Fixing Shutter HP error
Causes:	Home position error of the Fixing Shutter was detected.
Remedy:	[Related parts] R1.00 - Harness between the Feed/Drum Driver PCB (UN2/J213) and the Fixing Shutter Motor (M27/ J6059) - Harnesses connecting the Feed/Drum Driver PCB (UN2/J214), the Drawer Unit and the Fixing Relay PCB (UN78/J720) - Harness connecting from the Fixing Relay PCB (UN78/J722) to the Shutter HP Sensor and Shutter Position Sensor (PS31/J6103 and PS32/J6102) - Fixing Shutter Motor (M27) - Shutter HP Sensor (PS31) - Shutter Position Sensor (PS32) - Feed/Drum Driver PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts.

Error code:	880-0001-00
Description:	Controller Fan error
Causes:	It was detected that the Controller Fan was locked.
Remedy:	[Related parts] - Controller Cooling Fan (FM04) - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the connector of the Controller Cooling Fan. 2. Visually check that the Controller Cooling Fan is rotated. a. If it is not rotated, replace the Controller Cooling Fan. b. If it is rotated, replace the Main Controller PCB.

Error code:	880-0003-00
Description:	Controller Fan error
Causes:	It was detected that the Controller Fan was locked.
Remedy:	[Related parts] R1.00 - Cable between the Main Controller PCB (J15) and the Controller Fan (FM11) - Controller Fan (FM11) - Main Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. - Check the connectors of the Controller Fan. - Visually check rotation of the Controller Fan. a. If it is not rotated, replace the Controller Fan. b. If it is rotated, replace the Main Controller PCB.

Error code:	880-0005-00
Description:	Error in Controller Fan
Causes:	Fan lock of the HDD Cooling Fan was detected
Remedy:	Check if the connector is connected. It the connection is OK, replace the HDD Cooling Fan.

Error code:	881-0001-00
Description:	Board over heat error
Causes:	Abnormal temperature of the Main Controller CPU was detected.
Remedy:	[Related parts] - Main Controller PCB 1 (PWB01) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 1) - Main Controller PCB 2 (PWB02) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y, 2) [Remedy] Perform the following in the order while checking whether the error is cleared. a. If the error occurred during a service visit and then occurred again: 1. Replace the Main Controller PCB 1. 2. Replace the Main Controller PCB 2. [CAUTION] When replacing the Main Controller PCB 2, execute "Adjustment after the Main Controller PCB 2 replacement" in situation mode. b. If the error does not occur during a service visit but is found in the log: 1. Clean the inlet on the side where the fan is installed and remove dust. 2. Remove dust from the fan in the Controller Box. 3. If the space on the side where the fan is installed is less than 10 cm, ask the customer to secure enough space.

Error code:	882-0002-05
Description:	Main Power Supply Switch error
Causes:	The main power was not turned OFF due to the solenoid in the Main Power Switch not working.
Remedy:	[Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J109) and the Main Power Supply Switch (SW/ J1091 and J1092) - Main Power Supply Switch (SW1) - Riser PCB- DC Controller PCB (UN1) [Remedy] Perform the following in the order while checking whether the error is cleared. a. If the fuse (FU5) of the Riser PCB is blown out, 1. Check the harness and connector (caught cable, short circuit). 2. Check/replace the Riser PCB. b. If the fuse (FU5) of the Riser PCB is not blown out, 1. Check for any open circuit of the harness. 2. Check/replace the Main Power Supply Switch. 3. Check/replace the DC Controller PCB.

Error code:	996-0071-04
Description:	Error for collecting sequence jam log (ADF)
Causes:	Error for collecting jam log (ADF)
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-R" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CA1-05
Description:	Error for collecting sequence jam log (Printer)
Causes:	Error for collecting jam log (Printer)
Remedy:	Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CA2-05
Description:	Error for collecting sequence jam log (Printer)
Causes:	Error for collecting jam log (Printer)
Remedy:	Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CA3-05
Description:	Error for collecting sequence jam log (Printer)
Causes:	Error for collecting jam log (Printer)
Remedy:	Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CA4-05
Description:	Error for collecting sequence jam log (Printer)
Causes:	Error for collecting jam log (Printer)
Remedy:	Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CA5-05
Description:	Error for collecting sequence jam log (Printer)
Causes:	Error for collecting jam log (Printer)
Remedy:	Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CA6-05
Description:	Error for collecting log (Printer)
Causes:	Error for collecting log (Printer) Continuous 0CA6 jam was detected.
Remedy:	[Remedy] Collect debug log and contact the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CA7-05
Description:	Error for collecting log (Printer)
Causes:	Error for collecting log (Printer) Continuous 0CA7 jam was detected.
Remedy:	[Remedy] Collect debug log and contact the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CA9-05
Description:	Error for collecting log (Printer)
Causes:	Error for collecting log (Printer) Continuous 0CA9 jam was detected.
Remedy:	[Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CAA-05
Description:	Error for collecting log (Printer)
Causes:	Error for collecting log (Printer) Continuous 0CAA jam was detected.
Remedy:	Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CAB-05
Description:	Error for collecting log (Printer)
Causes:	Error for collecting log (Printer) Continuous 0CAB jam was detected.
Remedy:	Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CAC-05
Description:	Error for collecting log (Printer)
Causes:	Error for collecting log (Printer) Continuous 0CAC jam was detected.
Remedy:	Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Error code:	996-0CAE-05
Description:	Error for collecting log (Printer)
Causes:	Error for collecting log (Printer) Continuous 0CAE jam was detected.
Remedy:	Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence.

Деталь:	KNOB, 1
Парткод:	FB2-8094-020

Деталь:	GUIDE,2ND TRNSFER.OUTER,FRONT
Парткод:	FC8-4795-000

Деталь:	GUIDE, REG. HARD ROLLER, REAR
Парткод:	FC8-4796-000

Деталь:	PLATE, GROUNDING
Парткод:	FE4-3841-000

Деталь:	FOOT, GUIDE POSITIONING
Парткод:	FE4-3847-000

Деталь:	COVER, PAPER PICK-UP CABLE
Парткод:	FE4-4151-000

Деталь:	SUPPORT, CST. ROLLER, RIGHT 1
Парткод:	FE4-4624-000

Деталь:	SUPPORT, CST. ROLLER, RIGHT 2
Парткод:	FE4-4625-000

Деталь:	COVER, HEATER CONNECTOR
Парткод:	FE4-6047-000

Деталь:	SUPPORT, CASSETTE ROLLER, LEFT
Парткод:	FL1-0489-000

Деталь:	SENSOR UNIT, REG. PATCH
Парткод:	FM1-G456-000

Деталь:	PRE-REGISTRATION GUIDE ASSY
Парткод:	FM1-H144-000

Деталь:	DRAWING LINK ASSY, FRONT
Парткод:	FM3-8916-000

Деталь:	CONNECTOR, SNAP TIGHT, BK
Парткод:	VS1-7177-003

Деталь:	SHEET, PAPER DUST RELEASE
Парткод:	FC5-7403-000

Деталь:	LABEL, MULTIPLE
Парткод:	FE8-1364-000

Деталь:	CABLE, WASTE TONER
Парткод:	FM1-E910-000

Деталь:	SCREW,RS,M3X8
Парткод:	XA9-1386-000

Деталь:	RING, E
Парткод:	XD9-0137-010

Деталь:	PAPER PICK-UP DRIVE ASSEMBLY
Парткод:	FM1-G580-000

Деталь:	FLAG, 2ND DELIVERY SENSOR
Парткод:	FC5-0996-000

Деталь:	ROLLER, SECOND PAPER DELIVERY
Парткод:	FC8-4782-000

Деталь:	ROLLER, SECOND VERTICAL PATH
Парткод:	FC8-4789-000

Деталь:	GUIDE, SHAFT POSITIONING
Парткод:	FC8-5128-010

Деталь:	ELIMINATOR, STATIC CHARGE
Парткод:	FL1-0918-000

Деталь:	HINGE, SECOND PAPER DELIVERY
Парткод:	FL3-1142-000

Деталь:	PAPER DELIVERY ROLLER ASSEMBLY
Парткод:	FM1-G226-000

Деталь:	GEAR, 24T/PULLEY, 30T
Парткод:	FU5-3020-000

Деталь:	IC,PHOTO-INTERRUPTER,LG248NL1A
Парткод:	WG8-5783-000

Canon imageRUNNER Advance C5550i

Общие характеристики

Размещение

Цветность печати

Печать фотографий

Телефон

Тип устройства

Макс. формат

Копир

Факс

Сканер

Технология печати

Тип

Принтер

Макс, длина отпечатка

Макс, ширина отпечатка

Количество цветов

Пигментные чернила

Двусторонняя печать

Печать без полей

Макс, разрешение для ч/б печати

Скорость ч/б печати

Время выхода первого отпечатка

Копир

Шаг масштабирования

Макс, количество копий за цикл

Значение масштаба

Макс, разрешение (ч/б)

Сканер

Устройство автоподачи оригиналов

Слайд-адаптер

Макс. формат оригинала

Оттенки серого

Емкость устройства автоподачи оригиналов

Тип сканера

Стандарт TWAIN

Отправка изображения по e-mail

Макс, размер сканирования

Разрешение сканера

Скорость сканирования

Расходные материалы

Количество картриджей

Ресурс ч/б картриджа/тонера

Ресурс цветного картриджа/тонера

Печать на:

Плотность бумаги

Факс

PC Fax

Макс, скорость передачи данных

Память

Телефон

Проводная трубка

Автоответчик

Беспроводная трубка

Спикерфон

Caller ID

Стандарт DECT

АОН

Языки управления

Лотки

Емкость лотка ручной подачи

Подача бумаги

Вывод бумаги

Интерфейсы

Версия USB

USB

Ethernet (RJ-45)

Bluetooth

Wi-Fi

Устройство для чтения карт памяти

Инфракрасный порт

FireWire (IEEE 1394)

AirPrint

LPT

Память/Процессор

Частота процессора

Емкость жесткого диска

Объем памяти

Дополнительная информация

Работа от аккумулятора

Деталь:	BELT, TIMING, COGGED
Парткод:	XF2-4107-940

Деталь:	BEARING, BALL, MR106ZZ
Парткод:	XG9-0704-000

Деталь:	SECOND PAPER DELIVERY ASSEMBLY
Парткод:	FM1-G224-000

Деталь:	COUPLING, DEVELOPMENT
Парткод:	FC8-4170-000

Деталь:	PLATE, MOTOR MOUNTING
Парткод:	FC8-5323-000

Деталь:	CLUTCH, ELECTROMAGNETIC
Парткод:	FK2-7371-000

Деталь:	LABEL, MEMORY CAUTION
Парткод:	FC0-5049-000

Деталь:	MAIN CONTROLLER PCB ASSEMBLY
Парткод:	FM1-W953-000

Деталь:	SHEET, GLASS PROTECTIVE
Парткод:	FC0-9291-000

Деталь:	SPACER, SHAFT CUSHION
Парткод:	FE2-1752-000