Canon imageRUNNER Advance 4251
Рейтинг
Модули
400 READER ASSEMBLY
140 POWER CORD TERMINAL ASSEMBLY
350 FIRST DELIVERY ASSEMBLY
320 TRANSFER PAPER FEED ASSEMBLY
261 PAPER PICK-UP DRIVE ASSEMBLY (LOWER)(EXCEPT IR-ADV 4251)
351 SECOND DELIVERY ASSEMBLY
930 ENGINE CONTROLLER PCB ASSEMBLY
270 CARTRIDGE LEFT RAIL ASSEMBLY
263 DUPLEXING DRIVE ASSEMBLY
311 PAPER PICK-UP ASSEMBLY (LOWER)
920 MAIN CONTROLLER PCB ASSY, 2
460 LASER SCANNER ASSEMBLY
107 INTERNAL COMPONENTS 4
301 CASSETTE ASSEMBLY (LOWER)
130 CONTROL PANEL ASSEMBLY
103 MACHINE FRONT PLATE
620 HOPPER ASSEMBLY
300 CASSETTE ASSEMBLY (UPPER)
310 PAPER PICK-UP ASSEMBLY (UPPER)
B21 ESTRANGEMENT DRIVE ASSEMBLY (ADF MODEL)
102 RIGHT DOOR ASSEMBLY
104 INTERNAL COMPONENTS 1
316 PRE-REGISTRATION GUIDE ASSY
640 DEVELOPING ASSEMBLY
T21 SPEAKER ASSEMBLY (FAX)
313 DUPLEXING FEED GUIDE ASSEMBLY
105 INTERNAL COMPONENTS 2
T20 G3 FAX ASSEMBLY, 1 LINE (FAX)
280 FIRST DELIVERY DRIVE ASSEMBLY
108 INTERNAL COMPONENTS 5
B11 BASE ASSEMBLY (ADF MODEL)
330 RIGHT LOWER DOOR ASSEMBLY
110 MACHINE REAR PLATE 2
980 HIGH VOLTAGE PCB ASSEMBLY
333 RIGHT LOWER INNER DOOR ASSY
109 MACHINE REAR PLATE 1
352 SECOND DELIVERY FRAME ASSEMBLY
810 FIXING ASSEMBLY
910 MAIN CONTROLLER PCB ASSY, 1
250 MAIN DRIVE ASSEMBLY
900 CONTROLLER BOX ASSEMBLY
B41 PAPER FEED ASSEMBLY (ADF MODEL)
262 PAPER PICK-UP DRIVE ASSEMBLY (IR-ADV 4251)
B13 DOCUMENT TRAY ASSEMBLY (ADF MODEL)
106 INTERNAL COMPONENTS 3
D90 READER CONTROLLER PCB ASSEMBLY
B41 PAPER FEED ASSEMBLY (ADF MODEL) 2
312 MULTI PAPER PICK-UP ASSEMBLY
815 DELIVERY LOWER GUIDE ASSEMBLY
B10 ADF MAIN BODY (ADF MODEL)
271 CARTRIDGE RIGHT RAIL ASSEMBLY
B12 PAPER PICK-UP COVER ASSEMBLY (ADF MODEL)
770 WASTE TONER BOX ASSEMBLY
816 DELIVERY UPPER GUIDE ASSEMBLY
100 EXTERNAL COVERS, PANELS, ETC.
260 PAPER PICK-UP DRIVE ASSEMBLY (UPPER)(EXCEPT IR-ADV 4251)
Детали 320 TRANSFER PAPER FEED ASSEMBLY
| Деталь: | ARM, OPEN/CLOSE SENSOR |
| Парткод: | FC9-7292-000 |
| Деталь: | CORE HOLDER UNIT |
| Парткод: | FM4-8459-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | COVER, READER SUB, FRONT |
| Парткод: | FC0-2491-000 |
| Деталь: | COVER, READER SUB, REAR |
| Парткод: | FC0-2497-000 |
| Деталь: | COVER, READER SUB, REAR |
| Парткод: | FC0-2496-000 |
| Деталь: | LABEL, SERVICE |
| Парткод: | FL0-0207-000 |
| Деталь: | CARRIAGE UNIT |
| Парткод: | FM4-9642-000 |
| Деталь: | CASE, OPEN/CLOSE SENSOR |
| Парткод: | FC8-6188-010 |
| Деталь: | CASE, PAPER SIZE SENSOR |
| Парткод: | FC9-7284-000 |
| Деталь: | CCD MIRROR CLEANING UNIT |
| Парткод: | FL3-3207-000 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FC9-7297-000 |
| Деталь: | SCREW, FLAT HEAD, M4 |
| Парткод: | XA9-1415-000 |
| Деталь: | COVER, READER, FRONT |
| Парткод: | FC0-2490-000 |
| Деталь: | COVER, GLASS RETAINING |
| Парткод: | FC9-7288-000 |
| Деталь: | COVER, GLASS SUPPORT |
| Парткод: | FC0-2618-000 |
| Деталь: | COVER, HINGE, LEFT |
| Парткод: | FL3-5465-000 |
| Деталь: | COVER, HINGE, RIGHT |
| Парткод: | FL3-5309-000 |
| Деталь: | DOCUMENT SIZE SENSOR UNIT |
| Парткод: | FH7-7569-000 |
| Деталь: | CABLE, ADF I/F |
| Парткод: | FM4-7702-000 |
| Деталь: | SCREW, TP,M3X6 |
| Парткод: | XA9-1469-000 |
| Деталь: | GLASS, READER |
| Парткод: | FL3-3206-000 |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF2-4606-740 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2481-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FK3-1343-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU8-2497-000 |
| Деталь: | PHOTO-INTERRUPTER, SG2481 |
| Парткод: | WG8-5776-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-4668-040 |
| Деталь: | PLATE, SHAFT RETAINING |
| Парткод: | FC9-7308-000 |
| Деталь: | COVER, READER, REAR |
| Парткод: | FL3-6218-000 |
| Деталь: | PULLEY |
| Парткод: | FC8-6163-000 |
| Деталь: | PULLEY |
| Парткод: | FC8-6180-000 |
| Деталь: | PULLEY, 24T/41T |
| Парткод: | FU5-3710-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2470-000 |
| Деталь: | LABEL, COPY INHIBITED |
| Парткод: | FU7-8085-000 |
| Деталь: | LABEL, COPY INHIBITED |
| Парткод: | FU7-8086-000 |
| Деталь: | LABEL, COPY INHIBITED |
| Парткод: | FU7-8087-000 |
| Деталь: | LABEL, COPY INHIBITED |
| Парткод: | FU7-8227-000 |
| Деталь: | LABEL, COPY PROHIBITION, JAPAN |
| Парткод: | FU7-8084-000 |
| Деталь: | GLASS, COPYBOARD |
| Парткод: | FL3-3593-000 |
| Деталь: | GLASS, COPYBOARD |
| Парткод: | FL3-3594-000 |
| Деталь: | GLASS, COPYBOARD |
| Парткод: | FL3-3591-000 |
| Деталь: | LABEL, CLEANING POSITION |
| Парткод: | FU7-8080-000 |
| Деталь: | LABEL, CLEANING POSITION |
| Парткод: | FU7-8079-000 |
| Деталь: | CABLE, READER FLAT |
| Парткод: | FM4-7705-000 |
| Деталь: | COVER, READER, LEFT |
| Парткод: | FL3-6227-000 |
| Деталь: | COVER, READER, RIGHT |
| Парткод: | FL3-6226-000 |
| Деталь: | SHEET, CONNECTOR COVER |
| Парткод: | FE2-0755-000 |
| Деталь: | CABLE, HOME POSITION SENSOR |
| Парткод: | FM4-7700-000 |
| Деталь: | CABLE, MOTOR |
| Парткод: | FM4-7699-000 |
| Деталь: | CABLE,PAPER SIZE SENSOR |
| Парткод: | FM4-3390-000 |
| Деталь: | CABLE, POWER |
| Парткод: | FM4-7698-000 |
| Деталь: | CABLE, READER HEATER |
| Парткод: | FM4-7703-000 |
| Деталь: | CABLE,PAPER SIZE SENSOR |
| Парткод: | FM4-3389-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | NPN |
| Деталь: | CORD, POWER |
| Парткод: | FM4-0040-000 |
| Деталь: | POWER CORD |
| Парткод: | FM2-4786-000 |
| Деталь: | CABLE, AC INLET |
| Парткод: | FM4-7621-000 |
| Деталь: | CABLE, AC INLET |
| Парткод: | FM4-7675-000 |
| Деталь: | CORD, POWER |
| Парткод: | FM2-5951-000 |
| Деталь: | POWER CORD TERMINAL ASSY |
| Парткод: | NPN |
| Деталь: | LEVER, FULL DETECT |
| Парткод: | FC9-0806-010 |
| Деталь: | BUSHING |
| Парткод: | FC0-3073-000 |
| Деталь: | ROLLER, CURL |
| Парткод: | FC0-4672-000 |
| Деталь: | ROLLER, FD |
| Парткод: | FC8-0209-000 |
| Деталь: | LEVER, DELIVERY SENSOR |
| Парткод: | FC9-0802-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-0805-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-8959-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FL3-7222-000 |
| Деталь: | PLATE, ELIMINATOR |
| Парткод: | FL3-5302-000 |
| Деталь: | BUSHING, DELIVERY ROLLER |
| Парткод: | FU5-1522-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2925-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2968-000 |
| Деталь: | GEAR, 26T |
| Парткод: | FU8-0538-000 |
| Деталь: | FIRST PAPER DELIVERY ASSEMBLY |
| Парткод: | FM4-7915-000 |
| Деталь: | PIN, TRANSFER HINGE |
| Парткод: | FC0-4340-000 |
| Деталь: | PIN, TRANSFER HINGE |
| Парткод: | FC5-1536-000 |
| Деталь: | SHEET, PRE-REG. DOOR SIDE |
| Парткод: | FC9-0629-010 |
| Деталь: | GUIDE, ELIMINATOR |
| Парткод: | FC9-0702-000 |
| Деталь: | FLAG, LOOP SENSOR |
| Парткод: | FC9-0709-000 |
| Деталь: | ARM, TRANSFER, FRONT |
| Парткод: | FC9-0699-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2928-000 |
| Деталь: | ARM, TRANSFER, REAR |
| Парткод: | FC9-0700-000 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FM3-9299-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2930-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2931-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU8-2807-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2933-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | ROLLER, TRANSFER |
| Парткод: | FC9-0693-000 |
| Деталь: | ELIMINATOR HOLDER ASSEMBLY |
| Парткод: | FM3-9296-000 |
| Деталь: | SUPPORT, SENSOR FLAG |
| Парткод: | FE2-1943-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1009-000 |
| Деталь: | TRANSFER PAPER FEED ASSEMBLY |
| Парткод: | FM4-9155-000 |
| Деталь: | PULLEY, 34T |
| Парткод: | FC6-5022-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK2-7327-000 |
| Деталь: | GEAR, 80T/16T |
| Парткод: | FU3-0285-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1604-940 |
| Деталь: | PAPER PICK-UP DRIVE ASSY |
| Парткод: | FM4-7902-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2943-000 |
| Деталь: | RING, RETAINING |
| Парткод: | FC5-4697-000 |
| Деталь: | GUIDE, REVERSE LW. AUXILIARY |
| Парткод: | FC0-4692-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-0717-000 |
| Деталь: | GUIDE, SLIDE |
| Парткод: | FC9-0814-000 |
| Деталь: | FLAG, FULL SENSOR LEVER, |
| Парткод: | FC9-0816-010 |
| Деталь: | REVERSE SENSOR |
| Парткод: | FC9-0822-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC9-0836-000 |
| Деталь: | COLLAR, FIXING DELIVERY |
| Парткод: | FC9-7720-000 |
| Деталь: | SHEET, REVERSE AUXILIARY |
| Парткод: | FC9-7723-000 |
| Деталь: | ROLLER, REVERSE |
| Парткод: | FL3-1450-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FK3-1308-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0602-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0603-000 |
| Деталь: | GEAR, 35T |
| Парткод: | FU8-0605-000 |
| Деталь: | GEAR, 46T |
| Парткод: | FU8-0606-000 |
| Деталь: | GEAR, 35T |
| Парткод: | FU8-0610-000 |
| Деталь: | SIDE PLATE, 2ND PAPER DELIVERY |
| Парткод: | FM1-B597-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-040 |
| Деталь: | PULLEY |
| Парткод: | FU5-3796-000 |
| Деталь: | SPRING, RETAINING |
| Парткод: | FU7-2934-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7173-005 |
| Деталь: | GUIDE, REVERSE BACK END |
| Парткод: | FC0-4680-000 |
| Деталь: | 2ND PAPER DELIVERY DRIVE UNIT |
| Парткод: | FM4-7916-000 |
| Деталь: | SECOND PAPER DELIVERY ASSEMBLY |
| Парткод: | FM4-7337-010 |
| Деталь: | IC,TC200GO2EFG-1031,GATE ARRAY |
| Парткод: | FK2-1773-000 |
| Деталь: | IC, FSA0AC211AA |
| Парткод: | FK2-6450-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-A993-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-A994-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-A995-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-A996-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-A997-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-A998-000 |
| Деталь: | SCREW, STEPPED |
| Парткод: | FC9-0795-000 |
| Деталь: | STOPPER, DRUM |
| Парткод: | FC9-1618-000 |
| Деталь: | FAN |
| Парткод: | FK2-0360-000 |
| Цена: | 1 600 ₽ |
| Деталь: | CABLE, DRAWER |
| Парткод: | FM4-2918-000 |
| Деталь: | CABLE, ENGINE DRAWER DC |
| Парткод: | FM4-7624-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CABLE, FAN |
| Парткод: | FM4-7632-000 |
| Деталь: | CARTRIDGE LEFT RAIL ASSEMBLY |
| Парткод: | NPN |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FK3-1307-000 |
| Деталь: | BUSHING |
| Парткод: | FS5-1943-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2960-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0585-000 |
| Деталь: | PULLEY, 30T |
| Парткод: | FU9-0375-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1606-040 |
| Деталь: | DUPLEXING DRIVE ASSEMBLY |
| Парткод: | FM4-7917-000 |
| Деталь: | GUIDE, VERTICAL PATH |
| Парткод: | FB6-3387-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FB6-3410-000 |
| Деталь: | STOPPER, ROLLER |
| Парткод: | FC7-5845-000 |
| Деталь: | HOLDER, PAPER PICK-UP ROLLER |
| Парткод: | FC0-6755-000 |
| Деталь: | ROD, SEPARATION ROLLER RELEASE |
| Парткод: | FB6-3388-000 |
| Деталь: | CLAW, PICK-UP |
| Парткод: | FB6-3389-000 |
| Деталь: | GEAR, RATCHET |
| Парткод: | FB6-3391-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FB6-3392-020 |
| Деталь: | ARM, PAPER FEED SHAFT |
| Парткод: | FB6-3395-000 |
| Деталь: | LOCK, PICK-UP |
| Парткод: | FB6-3396-010 |
| Деталь: | FLAG, PAPER SENSOR |
| Парткод: | FB6-3397-000 |
| Деталь: | FLAG, PAPER DETECT SENSOR |
| Парткод: | FB6-3398-000 |
| Деталь: | GEAR, RATCHET |
| Парткод: | FB6-3402-000 |
| Деталь: | COUPLING, FEED SHAFT STOP |
| Парткод: | FB6-3403-000 |
| Деталь: | COUPLING, SEPARATION SHAFT |
| Парткод: | FB6-3404-000 |
| Деталь: | COLLAR, PAPER PICK-UP SHAFT |
| Парткод: | FB6-3413-000 |
| Деталь: | ROLLER, VERTICAL PATH |
| Парткод: | FB6-4852-000 |
| Деталь: | CABLE, PAPER PICK-UP UNIT |
| Парткод: | FG3-2302-020 |
| Деталь: | RING, RETAINING |
| Парткод: | FC6-9867-000 |
| Деталь: | CLAW, PAPER PICK-UP |
| Парткод: | FC8-1178-000 |
| Деталь: | DAMPER |
| Парткод: | FC8-1202-000 |
| Деталь: | JOINT, RETARD |
| Парткод: | FC9-4290-010 |
| Деталь: | ARM, LIFTING |
| Парткод: | FC9-7253-000 |
| Деталь: | GEAR, 46T |
| Парткод: | FL3-6661-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | SOLENOID |
| Парткод: | FK2-0408-000 |
| Деталь: | FLAG, REGISTRATION SENSOR |
| Парткод: | FL3-8032-000 |
| Деталь: | PICK-UP ARM UNIT |
| Парткод: | FM3-4146-000 |
| Деталь: | HOLDER, SEPARATION ROLLER |
| Парткод: | FM4-2525-000 |
| Деталь: | BUSHING |
| Парткод: | FS1-1205-000 |
| Деталь: | BUSHING |
| Парткод: | FS5-1943-000 |
| Деталь: | BUSHING |
| Парткод: | FS6-1063-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FS7-2800-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FS7-2801-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FS7-2803-000 |
| Деталь: | GEAR, 15T |
| Парткод: | FU0-0043-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU3-0282-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU3-0283-000 |
| Деталь: | GEAR, 16T |
| Парткод: | FU3-0284-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU3-0288-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU3-0289-000 |
| Деталь: | GEAR, 41T |
| Парткод: | FU3-0347-000 |
| Деталь: | GEAR, 41T |
| Парткод: | FU3-0349-000 |
| Деталь: | GEAR, 41T/41T |
| Парткод: | FU3-0350-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1763-000 |
| Деталь: | GEAR, 16T/16T |
| Парткод: | FU3-0352-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU6-2684-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU6-2784-000 |
| Деталь: | GEAR, 42T |
| Парткод: | FU7-0445-000 |
| Деталь: | GEAR, 51T |
| Парткод: | FU8-0214-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-5378-000 |
| Деталь: | BUSHING |
| Парткод: | RS5-1567-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | SCREW,RS,M3X10 |
| Парткод: | XA9-0656-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FB6-3405-000 |
| Цена: | 550 ₽ |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FC6-6661-000 |
| Цена: | 600 ₽ |
| Деталь: | ROLLER, FEED/SEPARATION |
| Парткод: | FC6-7083-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, 14P, W |
| Парткод: | VS1-7173-014 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-122 |
| Деталь: | PAPER PICK-UP ASSEMBLY |
| Парткод: | FM4-9177-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 2 |
| Парткод: | FM1-D272-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 2 |
| Парткод: | FM1-D273-000 |
| Деталь: | IC, MB87L8650, GATE ARRAY |
| Парткод: | FK2-3218-000 |
| Деталь: | IC, R8A03018ABG U100, ASIC |
| Парткод: | FK2-7835-010 |
| Деталь: | IC, T6TH5EFG-0002(0), STANDARD |
| Парткод: | FK2-7852-000 |
| Деталь: | IC, CLOCK GENERATOR, HYBRID |
| Парткод: | FK4-0572-000 |
| Деталь: | IC, MB87S1801 |
| Парткод: | FK2-8321-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 2 |
| Парткод: | NPN |
| Деталь: | LASER SCANNER ASSEMBLY |
| Парткод: | FM3-9406-010 |
| Деталь: | LASER SCANNER ASSEMBLY |
| Парткод: | FM3-9407-010 |
| Деталь: | CLIP |
| Парткод: | FC8-6380-000 |
| Деталь: | RAIL, FIXING, FRONT |
| Парткод: | FC9-0535-000 |
| Деталь: | RAIL, FIXING, REAR |
| Парткод: | FC9-0536-000 |
| Деталь: | MOTOR, DC |
| Парткод: | FK2-9141-000 |
| Деталь: | CLUTCH |
| Парткод: | FK2-9154-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, 10P, W |
| Парткод: | VS1-7173-010 |
| Деталь: | CONNECTOR, SNAP TIGHT, 13P, W |
| Парткод: | VS1-7173-013 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-015 |
| Деталь: | CABLE, DRIVE UNIT CONNECTING |
| Парткод: | FM4-7655-000 |
| Деталь: | CABLE, DRIVE UNIT |
| Парткод: | FM4-7706-000 |
| Деталь: | RING CORE |
| Парткод: | WE8-6787-000 |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | DIAL, DETECT, SMALL |
| Парткод: | FC8-2469-000 |
| Деталь: | DIAL, DETECT, LARGE |
| Парткод: | FC8-2470-000 |
| Деталь: | SHAFT, SUPPORT |
| Парткод: | FC8-2474-000 |
| Деталь: | PLATE, JOINT |
| Парткод: | FC8-2475-000 |
| Деталь: | PLATE, FREE STOP |
| Парткод: | FC8-2670-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-2671-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-2672-000 |
| Деталь: | LABEL, SIZE INDEX, SIDE, LARGE |
| Парткод: | FC8-4962-000 |
| Деталь: | COLLAR, REGISTRATION MULTI |
| Парткод: | FS5-6945-000 |
| Деталь: | LABEL, PAPER PICK-UP OPERATION |
| Парткод: | FC8-4966-000 |
| Деталь: | WINDOW, CST FR. COVER IND. |
| Парткод: | FC8-4967-000 |
| Деталь: | ROLLER, CASSETTE SWING |
| Парткод: | FC8-4970-000 |
| Деталь: | BUTTON, PUSHING |
| Парткод: | FC8-4985-000 |
| Деталь: | PIN, SIZE DETECT POSITIONING |
| Парткод: | FC8-4989-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FC8-4990-000 |
| Деталь: | WIRE,CENTER PLATE GROUNDING,L |
| Парткод: | FC8-4992-000 |
| Деталь: | PLATE, COVER ATTACHMENT, LEFT |
| Парткод: | FC8-4993-000 |
| Деталь: | COVER, TOP |
| Парткод: | FC8-4996-000 |
| Деталь: | SCREW, B, M4X8 |
| Парткод: | XA9-1523-000 |
| Деталь: | COVER, CASSETTE FRONT |
| Парткод: | FC8-8181-010 |
| Деталь: | RING, BUTTON |
| Парткод: | FC8-8182-000 |
| Деталь: | GEAR, 9T |
| Парткод: | FC9-0129-000 |
| Деталь: | LINK, BACK END DETECT |
| Парткод: | FC9-0130-000 |
| Деталь: | PAPER SIDE END EXTENSION ASSY |
| Парткод: | FM3-8912-000 |
| Деталь: | HOLDER, SIZE INDEX |
| Парткод: | FC9-0136-000 |
| Деталь: | COVER, SIZEPLATE |
| Парткод: | FC9-4042-000 |
| Деталь: | BACK END LIMIT PLATE ASSEMBLY |
| Парткод: | FM3-8907-000 |
| Деталь: | PLATE, CENTER |
| Парткод: | FL2-9472-000 |
| Деталь: | BUTTON LINK ASSEMBLY |
| Парткод: | FM3-8913-000 |
| Деталь: | PLATE, LIFTER |
| Парткод: | FL3-2859-000 |
| Деталь: | SIDE END PLATE ASSEMBLY, FRONT |
| Парткод: | FM3-8905-010 |
| Деталь: | SIDE END PLATE ASSEMBLY, REAR |
| Парткод: | FM3-8906-010 |
| Деталь: | CASSETTE ASSEMBLY |
| Парткод: | FM3-8153-000 |
| Деталь: | CONTROL PANEL ASSEMBLY, UPPER |
| Парткод: | FM1-D173-000 |
| Деталь: | COVER, CONTROL PANEL |
| Парткод: | FC0-2531-000 |
| Деталь: | COVER, LAMP |
| Парткод: | FC8-7823-000 |
| Деталь: | KEY TOP, BRIGHTNESS ADJUSTMENT |
| Парткод: | FC8-7824-000 |
| Деталь: | KEY TOP, VOLUME |
| Парткод: | FC8-7834-000 |
| Деталь: | KEY TOP, SETTINGS/REGISTRATION |
| Парткод: | FC8-8649-000 |
| Деталь: | KEY TOP, SLEEP |
| Парткод: | FC0-4942-000 |
| Деталь: | KEY TOP, STOP |
| Парткод: | FC9-9235-000 |
| Деталь: | KEY TOP, COUNTER CHECK |
| Парткод: | FC8-8655-000 |
| Деталь: | KEY TOP, NUMBERS |
| Парткод: | FC8-8660-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FC8-8679-000 |
| Деталь: | COVER, KEY TOP, LEFT |
| Парткод: | FC9-4390-000 |
| Деталь: | COVER, KEY TOP, RIGHT |
| Парткод: | FC9-4391-000 |
| Деталь: | COVER, PEN |
| Парткод: | FC9-4408-000 |
| Деталь: | KEY TOP, RESET KEY |
| Парткод: | FC9-9237-000 |
| Деталь: | TOP, CANCEL KEY |
| Парткод: | FC9-9238-000 |
| Деталь: | TOP, MAIN MENU |
| Парткод: | FC9-9239-000 |
| Деталь: | KEY TOP, PORTAL |
| Парткод: | FC9-9240-000 |
| Деталь: | GASKET |
| Парткод: | KE8-1168-100 |
| Деталь: | PEN, TOUCH PANEL |
| Парткод: | FL3-0626-000 |
| Деталь: | GASKET |
| Парткод: | KE8-1162-060 |
| Деталь: | KEY TOP, START |
| Парткод: | FL3-0833-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1118-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1119-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1120-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1121-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1122-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1123-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1124-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1125-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1112-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1113-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1114-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1115-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1116-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FL0-1117-000 |
| Деталь: | LCD UNIT |
| Парткод: | FL3-6215-000 |
| Деталь: | KEY TOP PCB ASSEMBLY |
| Парткод: | FM1-C889-000 |
| Деталь: | KEY TOP PCB ASSEMBLY, SUB |
| Парткод: | FM4-1195-000 |
| Деталь: | CONTROL PANEL VOLUME ASSEMBLY |
| Парткод: | FM4-1198-000 |
| Деталь: | CPU PCB ASSEMBLY |
| Парткод: | FM1-C888-000 |
| Деталь: | RING CORE |
| Парткод: | WE8-5731-000 |
| Деталь: | CABLE, CONTROL PANEL |
| Парткод: | FK4-0574-000 |
| Деталь: | TOUCH PANEL ASSEMBLY |
| Парткод: | FK2-8477-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A237-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A238-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A239-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A240-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A249-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A250-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A251-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A252-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A258-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A254-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A259-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A255-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A260-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A256-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | SENSOR, HUMIDITY |
| Парткод: | WP2-5316-000 |
| Деталь: | COVER, CONTROL, LOWER |
| Парткод: | FC0-2532-000 |
| Деталь: | LABEL, WASTE TONER UNLOCK |
| Парткод: | FC9-0504-000 |
| Деталь: | HOOK, RIGHT DOOR, LOWER |
| Парткод: | FC9-0900-000 |
| Деталь: | SWITCH, MAIN |
| Парткод: | FK3-2835-000 |
| Деталь: | HOOK, RIGHT DOOR, UPPER |
| Парткод: | FC9-0898-000 |
| Деталь: | HOOK, RIGHT DOOR, CENTER |
| Парткод: | FC9-0899-000 |
| Деталь: | HOOK, FRONT DOOR |
| Парткод: | FC9-1698-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2996-000 |
| Деталь: | SHUTTER, BOTTLE |
| Парткод: | FC0-2467-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU8-2792-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2794-000 |
| Деталь: | LEVER, BOTTLE EXCHANGE |
| Парткод: | FC9-0502-000 |
| Деталь: | LEVER, HANDLE LOCK |
| Парткод: | FC9-0503-000 |
| Деталь: | GEAR, 7T |
| Парткод: | FC9-7708-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2912-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2997-000 |
| Деталь: | SWITCH, MICRO |
| Парткод: | WC4-5242-000 |
| Деталь: | LABEL, LASER CAUTION |
| Парткод: | FU6-8880-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2911-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU6-2194-000 |
| Деталь: | HOLDER, SWITCH |
| Парткод: | FE3-3701-000 |
| Деталь: | PIN, HINGE |
| Парткод: | FA8-2446-000 |
| Деталь: | CABLE, ENVIRONMENT SENSOR |
| Парткод: | FM1-A975-000 |
| Деталь: | CABLE, DEVELOPING SENSOR |
| Парткод: | FM4-7688-000 |
| Деталь: | HOLDER, INTERLOCK |
| Парткод: | FC9-1701-000 |
| Деталь: | MACHINE FRONT PLATE |
| Парткод: | NPN |
| Деталь: | SUB HOPPER ASSEMBLY |
| Парткод: | FM4-7304-000 |
| Деталь: | ROD, STIRRING, AUXILIARY |
| Парткод: | FL3-6197-000 |
| Деталь: | HOLDER, RELEASE |
| Парткод: | FC0-2444-000 |
| Деталь: | COUPLING |
| Парткод: | FE3-5612-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-9022-010 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2791-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2919-000 |
| Деталь: | GEAR, 19T |
| Парткод: | FU8-0518-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU8-0519-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0520-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2793-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2806-000 |
| Деталь: | SEAL, OIL |
| Парткод: | MB4-8201-000 |
| Деталь: | SENSOR, ELECTROMAGNETIC |
| Парткод: | WP2-5282-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2800-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2803-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | BOX, DRIVE, FRONT |
| Парткод: | FC0-2452-000 |
| Деталь: | BOX, DRIVE, REAR |
| Парткод: | FC0-2453-000 |
| Деталь: | GEAR, WORM |
| Парткод: | FC9-0612-000 |
| Деталь: | MOTOR UNIT |
| Парткод: | FM4-7707-000 |
| Деталь: | GEAR, 43T/18T |
| Парткод: | FU8-0514-000 |
| Деталь: | GEAR, 73T |
| Парткод: | FU9-0326-000 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-0702-000 |
| Деталь: | BOX, DRIVE, FRONT |
| Парткод: | FC0-2454-000 |
| Деталь: | GEAR, 73T |
| Парткод: | FU9-0327-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | GEAR, 25T |
| Парткод: | FU9-0377-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD3-2200-162 |
| Деталь: | HOPPER ASSEMBLY |
| Парткод: | FM4-7913-000 |
| Деталь: | HOPPER ASSEMBLY |
| Парткод: | FM4-7914-000 |
| Деталь: | DIAL, DETECT, SMALL |
| Парткод: | FC8-2469-000 |
| Деталь: | DIAL, DETECT, LARGE |
| Парткод: | FC8-2470-000 |
| Деталь: | SHAFT |
| Парткод: | FC8-2474-000 |
| Деталь: | PLATE, JOINT |
| Парткод: | FC8-2475-000 |
| Деталь: | PLATE, FREE STOP |
| Парткод: | FC8-2670-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-2671-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-2672-000 |
| Деталь: | LABEL, PAPER PICK-UP OPERATION |
| Парткод: | FC8-4966-000 |
| Деталь: | ROLLER, CASSETTE SWING |
| Парткод: | FC8-4970-000 |
| Деталь: | PLATE, LIFTER |
| Парткод: | FL3-2859-000 |
| Деталь: | PIN, SIZE DETECT POSITIONING |
| Парткод: | FC8-4989-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FC8-4990-000 |
| Деталь: | COVER, TOP |
| Парткод: | FC8-4996-000 |
| Деталь: | GEAR, 9T |
| Парткод: | FC9-0129-000 |
| Деталь: | LINK, BACK END DETECT |
| Парткод: | FC9-0130-000 |
| Деталь: | LABEL, INDEX, SIZE M, BACK END |
| Парткод: | FC9-7243-000 |
| Деталь: | LABEL, INDEX, SIZE M, SIDE |
| Парткод: | FC9-7242-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FC9-0140-000 |
| Деталь: | PLATE, CENTER |
| Парткод: | FL2-9472-000 |
| Деталь: | COLLAR, REGISTRATION MULTI |
| Парткод: | FS5-6945-000 |
| Деталь: | SCREW, B, M4X8 |
| Парткод: | XA9-1523-000 |
| Деталь: | SIDE END PLATE ASSEMBLY, FRONT |
| Парткод: | FM3-8905-010 |
| Деталь: | SIDE END PLATE ASSEMBLY, REAR |
| Парткод: | FM3-8906-010 |
| Деталь: | BACK END LIMIT PLATE ASSEMBLY |
| Парткод: | FM3-8907-000 |
| Деталь: | PAPER SIDE END EXTENSION ASSY |
| Парткод: | FM3-8912-000 |
| Деталь: | CASSETTE FRONT COVER ASSY |
| Парткод: | FM4-7881-000 |
| Деталь: | WINDOW, CST FR. COVER IND. |
| Парткод: | FC8-4967-000 |
| Деталь: | PLATE, COVER ATTACHMENT, LEFT |
| Парткод: | FC8-4993-000 |
| Деталь: | HOLDER, SIZE INDEX |
| Парткод: | FC9-0136-000 |
| Деталь: | RING, BUTTON |
| Парткод: | FC8-8182-000 |
| Деталь: | BUTTON, PUSHING |
| Парткод: | FC8-4985-000 |
| Деталь: | LINK, BUTTON, UPPER, 2 |
| Парткод: | FC8-4986-000 |
| Деталь: | LINK, BUTTON, LOWER |
| Парткод: | FC8-4987-000 |
| Деталь: | COVER, SIZEPLATE |
| Парткод: | FC9-4042-000 |
| Деталь: | HOLDER, LOCK ARM, RIGHT |
| Парткод: | FC0-2590-000 |
| Деталь: | ARM, LOCK, A |
| Парткод: | FC9-7259-000 |
| Деталь: | ARM, LOCK, B |
| Парткод: | FC9-7260-000 |
| Деталь: | ROLLER, LINK |
| Парткод: | FC9-7261-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2518-000 |
| Деталь: | COVER, CASSETTE FRONT |
| Парткод: | FC8-8181-010 |
| Деталь: | CASSETTE ASSEMBLY |
| Парткод: | FM4-7880-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FB6-3410-000 |
| Деталь: | GUIDE, VERTICAL PATH |
| Парткод: | FC5-0595-010 |
| Деталь: | STOPPER, ROLLER |
| Парткод: | FC7-5845-000 |
| Деталь: | HOLDER, PAPER PICK-UP ROLLER |
| Парткод: | FC0-6755-000 |
| Деталь: | ROD, SEPARATION ROLLER RELEASE |
| Парткод: | FB6-3388-000 |
| Деталь: | CLAW, PICK-UP |
| Парткод: | FB6-3389-000 |
| Деталь: | GEAR, RATCHET |
| Парткод: | FB6-3391-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FB6-3392-020 |
| Деталь: | ARM, PAPER FEED SHAFT |
| Парткод: | FB6-3395-000 |
| Деталь: | LOCK, PICK-UP |
| Парткод: | FB6-3396-010 |
| Деталь: | FLAG, PAPER SENSOR |
| Парткод: | FB6-3397-000 |
| Деталь: | FLAG, PAPER DETECT SENSOR |
| Парткод: | FB6-3398-000 |
| Деталь: | GEAR, RATCHET |
| Парткод: | FB6-3402-000 |
| Деталь: | COUPLING, FEED SHAFT STOP |
| Парткод: | FB6-3403-000 |
| Деталь: | COUPLING, SEPARATION SHAFT |
| Парткод: | FB6-3404-000 |
| Деталь: | COLLAR, PAPER PICK-UP SHAFT |
| Парткод: | FB6-3413-000 |
| Деталь: | ROLLER, VERTICAL PATH |
| Парткод: | FB6-4852-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, 14P, W |
| Парткод: | VS1-7173-014 |
| Деталь: | RING, RETAINING |
| Парткод: | FC6-9867-000 |
| Деталь: | CLAW, PAPER PICK-UP |
| Парткод: | FC8-1178-000 |
| Деталь: | DAMPER |
| Парткод: | FC8-1202-000 |
| Деталь: | JOINT, RETARD |
| Парткод: | FC9-4290-010 |
| Деталь: | ARM, LIFTING |
| Парткод: | FC9-7253-000 |
| Деталь: | GEAR, 46T |
| Парткод: | FL3-6661-000 |
| Деталь: | SOLENOID |
| Парткод: | FK2-0408-000 |
| Деталь: | PICK-UP ARM UNIT |
| Парткод: | FM3-4146-000 |
| Деталь: | HOLDER, SEPARATION ROLLER |
| Парткод: | FM4-2525-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | BUSHING |
| Парткод: | FS1-1205-000 |
| Деталь: | BUSHING |
| Парткод: | FS5-1943-000 |
| Деталь: | BUSHING |
| Парткод: | FS6-1063-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FS7-2800-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FS7-2801-000 |
| Деталь: | GEAR, 15T |
| Парткод: | FU0-0043-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU3-0282-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU3-0283-000 |
| Деталь: | GEAR, 16T |
| Парткод: | FU3-0284-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU3-0288-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU3-0289-000 |
| Деталь: | GEAR, 41T |
| Парткод: | FU3-0347-000 |
| Деталь: | GEAR, 41T |
| Парткод: | FU3-0349-000 |
| Деталь: | GEAR, 41T/41T |
| Парткод: | FU3-0350-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1763-000 |
| Деталь: | GEAR, 16T/16T |
| Парткод: | FU3-0352-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU6-2684-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU6-2784-000 |
| Деталь: | GEAR, 42T |
| Парткод: | FU7-0445-000 |
| Деталь: | GEAR, 51T |
| Парткод: | FU8-0214-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-5378-000 |
| Деталь: | BUSHING |
| Парткод: | RS5-1567-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | SCREW,RS,M3X10 |
| Парткод: | XA9-0656-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FB6-3405-000 |
| Цена: | 550 ₽ |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FC6-6661-000 |
| Цена: | 600 ₽ |
| Деталь: | ROLLER, FEED/SEPARATION |
| Парткод: | FC6-7083-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-122 |
| Деталь: | PAPER PICK-UP ASSEMBLY |
| Парткод: | FM4-9175-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | DUCT, ESTRANGEMENT HARNESS |
| Парткод: | FC8-6406-000 |
| Деталь: | CAM, ESTRANGEMENT |
| Парткод: | FC8-6407-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FK2-0207-000 |
| Деталь: | GEAR/PULLEY, 40T/20T |
| Парткод: | FU8-0311-000 |
| Деталь: | GEAR, 31T |
| Парткод: | FU8-0319-000 |
| Деталь: | GEAR, 30T |
| Парткод: | FU8-0320-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | PHOTO INTEUPTE, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | SCREW,RS,M4 |
| Парткод: | XA9-0732-010 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1607-640 |
| Деталь: | SPRING, LEAF |
| Парткод: | FC0-4617-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FC0-9122-010 |
| Деталь: | ESTRANGEMENT DRIVE ASSEMBLY |
| Парткод: | NPN |
| Деталь: | GUIDE, AUXILIARY |
| Парткод: | FC0-2458-010 |
| Деталь: | GUIDE, DUPLEXING PAPER FEED |
| Парткод: | FC0-2489-000 |
| Деталь: | COLLAR, FIXING DELIVERY |
| Парткод: | FC5-1358-000 |
| Деталь: | CAP, SPRING |
| Парткод: | FC5-6014-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-0717-000 |
| Деталь: | COVER, MULTI ROLLER |
| Парткод: | FE2-0503-000 |
| Деталь: | FAN |
| Парткод: | FK2-0360-000 |
| Цена: | 1 600 ₽ |
| Деталь: | FAN |
| Парткод: | FK2-0472-010 |
| Деталь: | ROLLER, DUPLEXING PAPER FEED |
| Парткод: | FL3-1448-000 |
| Деталь: | HOOK HOLDER UNIT |
| Парткод: | FM3-9249-000 |
| Деталь: | HOOK, WIRE |
| Парткод: | FC9-1710-000 |
| Деталь: | BUTTON, RIGHT DOOR |
| Парткод: | FC0-4685-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2998-000 |
| Деталь: | DUPLEXING PAPER FEED ASSEMBLY |
| Парткод: | FM4-9152-000 |
| Деталь: | FLAG, REVERSE DETECT |
| Парткод: | FC9-8965-010 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC9-8966-000 |
| Деталь: | ROLLER, DUPLEXING PAPER FEED |
| Парткод: | FL3-6203-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FC6-2931-000 |
| Деталь: | GEAR, 26T/26T |
| Парткод: | FU9-0384-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | PULLEY |
| Парткод: | FU5-3796-000 |
| Деталь: | COLLAR |
| Парткод: | FU5-6014-000 |
| Деталь: | SPRING, RETAINING |
| Парткод: | FU8-2883-000 |
| Деталь: | GEAR, 28T |
| Парткод: | FU8-0530-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2798-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-3111-840 |
| Деталь: | CONNECTOR, SNAP TIGHT, 3P |
| Парткод: | VS1-7173-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-005 |
| Деталь: | LABEL, HIGH TMP. CAUTION |
| Парткод: | FE2-0747-000 |
| Деталь: | SHEET, STATIC CHARGE |
| Парткод: | FL0-2763-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD3-2200-142 |
| Деталь: | RIGHT DOOR ASSEMBLY |
| Парткод: | FM4-9154-030 |
| Деталь: | CAM, DOOR HINGE, RIGHT |
| Парткод: | FC0-2537-000 |
| Деталь: | GUIDE, DUPLEXING AUXILIARY |
| Парткод: | FC0-5233-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-0545-000 |
| Деталь: | ROLLER, REGISTRATION PRESSURE |
| Парткод: | FC9-0552-000 |
| Деталь: | GEAR, 17T |
| Парткод: | FU8-0508-000 |
| Деталь: | LEVER, RIGHT |
| Парткод: | FC9-0562-010 |
| Деталь: | BALL BEARING UNIT, L-1680HHP0P |
| Парткод: | FC0-2459-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC9-0989-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC9-0990-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC9-0991-000 |
| Деталь: | FOOT, RUBBER |
| Парткод: | XH9-0136-000 |
| Деталь: | CLUTCH |
| Парткод: | FK2-9154-000 |
| Деталь: | CLIP |
| Парткод: | FC8-6380-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-025 |
| Деталь: | CABLE, DOOR CONNECTING, RIGHT |
| Парткод: | FM4-7670-000 |
| Деталь: | HINGE, RIGHT DOOR, LOWER |
| Парткод: | FC0-2513-000 |
| Деталь: | SPRING PIN |
| Парткод: | XD3-1200-122 |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | CABLE, GROUNDING |
| Парткод: | FC9-0557-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, 6P, W |
| Парткод: | VS1-7173-006 |
| Деталь: | PHOTOINTERRUPTER, PS122TL1-A |
| Парткод: | WG8-5927-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | PRE-REGISTRATION GUIDE ASSY |
| Парткод: | FM4-7921-000 |
| Деталь: | ROLLER |
| Парткод: | FC0-5122-000 |
| Деталь: | RING, C |
| Парткод: | FC0-5242-000 |
| Деталь: | HOLDER, DEVELOPING FRONT |
| Парткод: | FC9-0592-010 |
| Деталь: | FEEDSCREW, TONER |
| Парткод: | FC9-1610-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-1613-000 |
| Деталь: | BLADE ASSEMBLY |
| Парткод: | FM3-9265-000 |
| Деталь: | GEAR, 18T/18T |
| Парткод: | FU8-0509-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0510-000 |
| Деталь: | GEAR, 31T/13T |
| Парткод: | FU8-0512-000 |
| Деталь: | DEVELOPING CYLINDER ASSEMBLY |
| Парткод: | FM4-9170-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2916-000 |
| Деталь: | GEAR, 16T |
| Парткод: | FU8-0511-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU8-0553-000 |
| Деталь: | GEAR, 20T |
| Парткод: | FU9-0383-000 |
| Деталь: | SEAL, OIL |
| Парткод: | MB4-8201-000 |
| Деталь: | SENSOR, ELECTROMAGNETIC |
| Парткод: | WP2-5282-000 |
| Деталь: | BEARING, BALL, L-1680HH LY13 |
| Парткод: | XG9-0387-000 |
| Деталь: | WASHER, TOOTHED LOCK, M3 |
| Парткод: | XD1-4200-302 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD3-2200-142 |
| Деталь: | DEVELOPING ASSEMBLY |
| Парткод: | FM4-9730-000 |
| Деталь: | SPEAKER |
| Парткод: | FK2-0428-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1567-000 |
| Деталь: | SPEAKER ASSEMBLY |
| Парткод: | FM4-9135-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-0717-000 |
| Деталь: | RATCHET, INTERMEDIATE |
| Парткод: | FC9-0826-000 |
| Деталь: | ARM, SOLENOID, 2 |
| Парткод: | FC5-1023-000 |
| Деталь: | COVER, REVERSE SOLENOID |
| Парткод: | FC9-0838-000 |
| Деталь: | SHEET, REVERSE SOLENOID |
| Парткод: | FC9-8950-000 |
| Деталь: | SOLENOID |
| Парткод: | FH6-5095-000 |
| Деталь: | COVER, AIR FILTER |
| Парткод: | FC0-3079-000 |
| Деталь: | RATCHET, FEED |
| Парткод: | FC9-0852-000 |
| Деталь: | ROLLER, ENTRANCE |
| Парткод: | FL3-1451-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | DUPLEXING ENTRANCE GUIDE ASSY |
| Парткод: | FM4-9740-000 |
| Деталь: | FLAPPER, SECOND DELIVERY |
| Парткод: | FC9-0841-000 |
| Деталь: | GUIDE, REVERSE ENTRANCE |
| Парткод: | FC9-0843-000 |
| Деталь: | FLAPPER, REVERSE |
| Парткод: | FC9-0846-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-0923-000 |
| Деталь: | COLLAR, FIXING DELIVERY |
| Парткод: | FC9-7720-000 |
| Деталь: | GUIDE, ENTRANCE |
| Парткод: | FL3-1443-000 |
| Деталь: | SPRING, RETAINING |
| Парткод: | FU7-2947-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU8-2805-000 |
| Деталь: | GEAR, 35T |
| Парткод: | FU8-0607-000 |
| Деталь: | FILTER, AIR |
| Парткод: | FC0-3078-000 |
| Деталь: | DUPLEXING FEED GUIDE ASSEMBLY |
| Парткод: | FM4-9157-000 |
| Деталь: | HANDLE, PRESSURE |
| Парткод: | FC9-0512-000 |
| Деталь: | SLIDER, LASER SHUTTER |
| Парткод: | FC9-0533-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2913-000 |
| Деталь: | LINK, LASER SHUTTER |
| Парткод: | FC9-1623-010 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2972-000 |
| Деталь: | FAN |
| Парткод: | FK2-0472-010 |
| Деталь: | CAM, DEVELOPING PRESSURE |
| Парткод: | FC9-0609-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2801-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1030-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6823-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, 10P, W |
| Парткод: | VS1-7173-010 |
| Деталь: | CABLE, HOPPER CONNECTING |
| Парткод: | FM4-7689-000 |
| Деталь: | CABLE, POLYGON MOTOR |
| Парткод: | FM4-7623-000 |
| Деталь: | CABLE, LASER |
| Парткод: | FM4-7629-000 |
| Деталь: | CABLE, LASER |
| Парткод: | FM4-7633-000 |
| Деталь: | CABLE, BD |
| Парткод: | FM1-A985-000 |
| Деталь: | CABLE, BD |
| Парткод: | FM1-A999-000 |
| Деталь: | CABLE, COOLING FAN |
| Парткод: | FM1-C863-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | 1 LINE PCB ASSEMBLY |
| Парткод: | FM1-C887-000 |
| Деталь: | MODULAR PCB ASSEMBLY |
| Парткод: | FM4-2476-000 |
| Деталь: | CABLE, SPEAKER |
| Парткод: | FM1-A986-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CABLE, FAX CB |
| Парткод: | FM1-A980-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6991-000 |
| Деталь: | CABLE, MODULAR |
| Парткод: | FM1-A991-000 |
| Деталь: | CABLE, GROUNDING |
| Парткод: | FM1-A989-000 |
| Деталь: | CABLE, ARESTA GROUNDING |
| Парткод: | FM4-7694-000 |
| Деталь: | MODULAR CORD, 2P |
| Парткод: | HH2-2824-000 |
| Деталь: | G3 FAX ASSEMBLY, 1 LINE |
| Парткод: | NPN |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FK3-1309-000 |
| Деталь: | GEAR, 18T/PULLEY, 20T |
| Парткод: | FU9-0376-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1603-640 |
| Деталь: | FIRST DELIVERY DRIVE ASSEMBLY |
| Парткод: | FM4-7918-000 |
| Деталь: | SCREW, STEPPED, M5X6 |
| Парткод: | FU5-9139-000 |
| Деталь: | SCREW, FIXED, M4 |
| Парткод: | FU5-9167-000 |
| Деталь: | COVER, HINGE BLANKING |
| Парткод: | FC9-6192-010 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | PLATE, READER JOINT, LEFT |
| Парткод: | FL3-5310-000 |
| Деталь: | PLATE, READER JOINT, RIGHT |
| Парткод: | FC0-2499-000 |
| Деталь: | SHEET, BLANKING |
| Парткод: | FC9-6193-000 |
| Деталь: | INTERNAL COMPONENTS 5 |
| Парткод: | NPN |
| Деталь: | SHAFT, PAPER FEED ROLLER |
| Парткод: | FC5-4285-030 |
| Деталь: | ROLLER, PAPER FEED, 1 |
| Парткод: | FC5-4286-000 |
| Деталь: | ROLLER, PAPER FEED, 2 |
| Парткод: | FC5-4287-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FC6-8973-000 |
| Деталь: | HOLDER, SOLENOID |
| Парткод: | FC8-6319-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FC8-6322-000 |
| Деталь: | ROLLER, READ 2 PINCH |
| Парткод: | FC8-6404-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2652-000 |
| Деталь: | SHEET, PAPER FEED |
| Парткод: | FC8-6422-000 |
| Деталь: | SHEET, PAPER FEED |
| Парткод: | FC8-6423-000 |
| Деталь: | HOLDER, ROLLER, SMALL |
| Парткод: | FL2-9933-000 |
| Деталь: | HOLDER, ROLLER, LARGE |
| Парткод: | FL2-9934-010 |
| Деталь: | COVER, BASE, LOWER |
| Парткод: | FL3-2942-000 |
| Деталь: | LEVER, READ 1 PRESSURE |
| Парткод: | FC8-6331-000 |
| Деталь: | COLLAR, READ 1 PRESSURE |
| Парткод: | FC8-6332-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2653-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1168-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6316-000 |
| Деталь: | HOLDER, DELIVERY ROLLER |
| Парткод: | FC8-6317-000 |
| Деталь: | CAM, DELIVERY ESTRANGEMENT |
| Парткод: | FC8-6318-010 |
| Деталь: | DAMPER, DELIVERY |
| Парткод: | FC8-6419-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-122 |
| Деталь: | BASE ASSEMBLY (ADF MODEL) |
| Парткод: | NPN |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FB6-3313-000 |
| Деталь: | GUIDE, DOOR, RIGHT LOWER |
| Парткод: | FC0-2517-000 |
| Деталь: | GUIDE, DECK PATH |
| Парткод: | FC0-2518-000 |
| Деталь: | HANDLE, RIGHT DOOR, LOWER |
| Парткод: | FC0-2519-000 |
| Деталь: | STOPPER, DOOR, RIGHT LOWER |
| Парткод: | FC0-2520-000 |
| Деталь: | HOOK, RIGHT LOWER DOOR, FRONT |
| Парткод: | FC0-2521-000 |
| Деталь: | HOOK, RIGHT LOWER DOOR, REAR |
| Парткод: | FC0-2522-000 |
| Деталь: | CAM |
| Парткод: | FC0-2528-000 |
| Деталь: | CAM |
| Парткод: | FC0-2529-000 |
| Деталь: | COVER, DECK PATH |
| Парткод: | FC8-4861-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FS7-2788-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1035-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2796-000 |
| Деталь: | DOOR ASSEMBLY, RIGHT LOWER |
| Парткод: | FM4-7332-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | RAIL, HARD DISK DRIVE GUIDE |
| Парткод: | FC8-4051-000 |
| Деталь: | PIN, LOCK |
| Парткод: | FC9-7865-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2289-000 |
| Деталь: | DAMPER, BUSHING |
| Парткод: | FE2-0465-000 |
| Деталь: | HDD, MK1676GSX, TOSHIBA |
| Парткод: | FK3-2219-000 |
| Деталь: | SCREW, STEPPED, M3 |
| Парткод: | FE2-0468-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-011 |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6817-000 |
| Деталь: | CABLE, USB |
| Парткод: | FK4-0575-000 |
| Деталь: | LABEL, CAUTION |
| Парткод: | FU8-8257-000 |
| Деталь: | DAMPER |
| Парткод: | FE3-1776-000 |
| Деталь: | CABLE, POWER SUPPLY REMOTE |
| Парткод: | FM1-A979-000 |
| Деталь: | CABLE, ENVIRONMENT ESS |
| Парткод: | FM1-A977-000 |
| Деталь: | CABLE, SWITCH AC |
| Парткод: | FM1-A972-000 |
| Деталь: | CABLE, DRIVE UNIT |
| Парткод: | FM4-7657-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | SPACER |
| Парткод: | XZ1-1301-005 |
| Деталь: | SPACER |
| Парткод: | XZ1-1300-605 |
| Деталь: | MACHINE REAR PLATE |
| Парткод: | NPN |
| Деталь: | H.V. TRANSFER PCB ASSEMBLY |
| Парткод: | FM4-7615-000 |
| Деталь: | HIGH VOLTAGE PCB ASSEMBLY |
| Парткод: | NPN |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FB6-3313-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FC7-5907-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FS7-2788-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1035-000 |
| Деталь: | RIGHT LOWER INNER DOOR ASSY |
| Парткод: | FM3-1297-000 |
| Деталь: | HANDLE |
| Парткод: | FC6-4689-000 |
| Деталь: | FAN |
| Парткод: | FK2-0360-000 |
| Цена: | 1 600 ₽ |
| Деталь: | MOTOR, DC |
| Парткод: | FK2-9145-000 |
| Деталь: | BUSHING |
| Парткод: | FC7-2409-000 |
| Деталь: | POWER SUPPLY ASSEMBLY |
| Парткод: | FM1-A232-000 |
| Деталь: | POWER SUPPLY ASSEMBLY |
| Парткод: | FM1-A233-000 |
| Деталь: | POWER SUPPLY ASSEMBLY |
| Парткод: | FM1-A231-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC0-2577-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC0-2578-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC0-2579-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC0-2580-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC0-2581-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC9-0992-000 |
| Деталь: | SPRING, CONTACT |
| Парткод: | FC9-0993-000 |
| Деталь: | CABLE, READER CONTROLLER |
| Парткод: | FM1-A982-000 |
| Деталь: | CASSETTE HEATER PCB ASSEMBLY |
| Парткод: | FM4-8594-000 |
| Деталь: | CASSETTE HEATER PCB ASSEMBLY |
| Парткод: | FM4-8593-000 |
| Деталь: | GEAR, 106T |
| Парткод: | FU9-0324-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU9-0385-000 |
| Деталь: | CABLE, OPTION CASSETTE |
| Парткод: | FM4-7653-000 |
| Деталь: | CABLE, ENVIRONMENT SWITCH |
| Парткод: | FM4-7627-000 |
| Деталь: | CABLE, DECK LATTICE |
| Парткод: | FM1-C867-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6823-000 |
| Деталь: | CABLE, FINISHER SIGNAL |
| Парткод: | FM1-C859-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FC0-0205-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-015 |
| Деталь: | CABLE, ENGINE CONTROLLER |
| Парткод: | FM1-A976-000 |
| Деталь: | CABLE, ENGINE CONTROLLER CB |
| Парткод: | FM1-C862-000 |
| Деталь: | CABLE, HIGH VOLTAGE TRANSFER |
| Парткод: | FM4-7625-000 |
| Деталь: | CABLE, READER HEATER |
| Парткод: | FM4-7639-000 |
| Деталь: | WASHER, TOOTHED LOCK, M4 |
| Парткод: | XD1-4200-402 |
| Деталь: | MACHINE REAR PLATE |
| Парткод: | NPN |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-040 |
| Деталь: | GEAR, 24T |
| Парткод: | FU8-0609-000 |
| Деталь: | ROLLER, FD |
| Парткод: | FC0-5231-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-0974-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-0997-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | CAP, SPRING |
| Парткод: | FC5-6014-000 |
| Деталь: | RATCHET, FEED |
| Парткод: | FC9-0854-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FC9-0856-000 |
| Деталь: | ROLLER, VERTICAL PASS |
| Парткод: | FC9-0857-000 |
| Деталь: | STOPPER, BELT |
| Парткод: | FC9-0864-000 |
| Деталь: | FLAPPER |
| Парткод: | FC9-0870-010 |
| Деталь: | BUSHING |
| Парткод: | FC9-0923-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-8967-000 |
| Деталь: | ROLLER, SECOND DELIVERY |
| Парткод: | FL3-1454-000 |
| Деталь: | SOLENOID |
| Парткод: | FL3-3151-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | BUSHING |
| Парткод: | FS5-1943-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU5-0076-000 |
| Деталь: | BUSHING, DELIVERY ROLLER |
| Парткод: | FU5-1522-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU6-2189-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2946-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2948-000 |
| Деталь: | GEAR, 26T |
| Парткод: | FU8-0608-000 |
| Деталь: | SECOND DELIVERY FRAME ASSEMBLY |
| Парткод: | FM4-7924-000 |
| Деталь: | LABEL, CAUTION |
| Парткод: | FE2-0466-000 |
| Деталь: | ROWEL |
| Парткод: | FE2-2846-000 |
| Деталь: | HOLDER, FIXING DELIVERY, UPPER |
| Парткод: | FC0-3069-000 |
| Деталь: | CAP,DUST |
| Парткод: | FC0-0293-000 |
| Деталь: | GUIDE, DELIVERY LOWER |
| Парткод: | FC0-2394-000 |
| Деталь: | COLLAR, FIXING DELIVERY |
| Парткод: | FC0-2406-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FC0-2413-000 |
| Деталь: | SCREW, STEPPED |
| Парткод: | FC0-4356-000 |
| Деталь: | SPRING,SENSOR LEVER |
| Парткод: | FC5-1367-000 |
| Деталь: | HOUSING,BEARING |
| Парткод: | FC5-7182-000 |
| Деталь: | LEVER, PRESSURE RELEASE, REAR |
| Парткод: | FC9-0738-000 |
| Деталь: | GUIDE, FIXING ENTRANCE, 1 |
| Парткод: | FC9-0781-010 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC9-0782-000 |
| Деталь: | RACK, PRESSURE RELEASE |
| Парткод: | FC9-0787-010 |
| Деталь: | BUSHING |
| Парткод: | FC9-0790-000 |
| Деталь: | GEAR, 7T |
| Парткод: | FC9-0792-000 |
| Деталь: | GUIDE, FIXING ENTRANCE, 2 |
| Парткод: | FE2-0749-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC9-8968-000 |
| Деталь: | ROLLER, PRESSURE |
| Парткод: | FC9-8974-000 |
| Деталь: | H.V. CONTACT GUIDE ASSEMBLY |
| Парткод: | FM3-9401-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM4-7897-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM4-7898-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM4-7900-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM4-7901-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM4-7899-000 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-0702-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2881-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2788-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0386-000 |
| Деталь: | GEAR, 36T |
| Парткод: | FU9-0576-000 |
| Деталь: | GEAR, 15T/22T |
| Парткод: | FU9-0577-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | BALL BEARING, NSK, 688AZZ1MC4E |
| Парткод: | XG9-0172-000 |
| Деталь: | LABEL,HIGH TEMPERATURE CAUTION |
| Парткод: | FU6-8898-000 |
| Деталь: | FIXING ASSEMBLY, MAIN |
| Парткод: | FM4-9733-000 |
| Деталь: | FIXING ASSEMBLY, MAIN |
| Парткод: | FM4-9734-000 |
| Деталь: | FIXING ASSEMBLY, MAIN |
| Парткод: | FM4-9736-000 |
| Деталь: | FIXING ASSEMBLY, MAIN |
| Парткод: | FM4-9737-000 |
| Деталь: | FIXING ASSEMBLY, MAIN |
| Парткод: | FM4-9735-000 |
| Деталь: | GUIDE, RELEASE |
| Парткод: | FC9-0785-000 |
| Деталь: | GUIDE, FIXING CABLE, A |
| Парткод: | FC0-2417-000 |
| Деталь: | GUIDE, FIXING CABLE, B |
| Парткод: | FC0-2418-000 |
| Деталь: | FIXING ASSEMBLY |
| Парткод: | NPN |
| Деталь: | MAIN CONTROLLER PCB ASSY, 1 |
| Парткод: | FM1-D268-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 1 |
| Парткод: | FM1-D269-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 1 |
| Парткод: | FM1-D270-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 1 |
| Парткод: | FM1-D271-000 |
| Деталь: | FAN |
| Парткод: | FK2-8276-000 |
| Деталь: | TPM PCB ASSEMBLY |
| Парткод: | FM1-C876-000 |
| Деталь: | IC, 88E8075B0-NNC2C000, |
| Парткод: | FK2-9794-000 |
| Деталь: | IC, AU80610006252AASLBXD, MPU |
| Парткод: | FK3-2222-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 1 |
| Парткод: | NPN |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE2-0459-000 |
| Деталь: | COUPLING |
| Парткод: | FC9-0922-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-0923-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-0924-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-1593-000 |
| Деталь: | COUPLING, DRUM |
| Парткод: | FC7-2666-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2962-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2960-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2961-000 |
| Деталь: | GEAR, 40T |
| Парткод: | FU8-0539-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU8-0540-000 |
| Деталь: | GEAR, 99T/52T |
| Парткод: | FU8-0541-000 |
| Деталь: | GEAR, 99T/75T |
| Парткод: | FU8-0542-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0547-000 |
| Деталь: | GEAR, 35T/26T |
| Парткод: | FU8-0555-000 |
| Деталь: | GEAR, 24T/39T |
| Парткод: | FU9-0378-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU9-0379-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0380-000 |
| Деталь: | GEAR, 37T/87T |
| Парткод: | FU9-0381-000 |
| Деталь: | GEAR, 29T |
| Парткод: | FU9-0382-000 |
| Деталь: | BEARING, BALL, F688ZZ |
| Парткод: | XG9-0508-000 |
| Деталь: | PIN, DOWELL, 2.5X12 |
| Парткод: | XD3-2250-122 |
| Деталь: | PIN |
| Парткод: | XD3-2200-222 |
| Деталь: | MAIN DRIVE ASSEMBLY |
| Парткод: | FM4-9179-000 |
| Деталь: | HOLDER, PCB |
| Парткод: | FC0-2548-000 |
| Деталь: | COVER, HARD DISK DRIVE |
| Парткод: | FC0-4359-000 |
| Деталь: | BUSHING, FFC |
| Парткод: | FC6-7576-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | CABLE, HDD SIGNAL |
| Парткод: | FK3-1597-000 |
| Деталь: | CABLE, HDD POWER SUPPLY |
| Парткод: | FK3-1596-000 |
| Деталь: | CONTROLLER BOX ASSEMBLY |
| Парткод: | NPN |
| Деталь: | FLANGE, BELT |
| Парткод: | FC5-4353-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FC6-8973-000 |
| Деталь: | GUIDE, PLATEN, 2 |
| Парткод: | FC8-6368-000 |
| Деталь: | FLAPPER, REVERSE |
| Парткод: | FL2-9949-000 |
| Деталь: | LEVER, READ SENSOR |
| Парткод: | FC8-6371-000 |
| Деталь: | LEVER, PAPER DELIVERY SENSOR |
| Парткод: | FC8-6372-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FC8-6377-000 |
| Деталь: | DUCT, HARNESS |
| Парткод: | FC8-6378-020 |
| Деталь: | FLANGE, PULLEY |
| Парткод: | FC8-6379-000 |
| Деталь: | CLIP |
| Парткод: | FC8-6380-000 |
| Деталь: | ROLLER, BELT TENSION |
| Парткод: | FC8-6382-000 |
| Деталь: | JOINT, DELIVERY GEAR |
| Парткод: | FC8-6385-000 |
| Деталь: | DIAL, JAM |
| Парткод: | FC0-4616-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6395-010 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FC8-6396-000 |
| Деталь: | ROLLER, READ |
| Парткод: | FC0-4619-000 |
| Деталь: | JOINT, READ PULLEY |
| Парткод: | FC8-6418-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FC8-6421-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FM1-F816-000 |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | FK2-6870-000 |
| Деталь: | FLAG, REGISTRATION SENSOR |
| Парткод: | FL2-9937-000 |
| Деталь: | BEARING, BALL, MF128ZZ |
| Парткод: | XG9-0507-000 |
| Деталь: | JOINT, PICK-UP |
| Парткод: | FC8-6383-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-6411-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0304-000 |
| Деталь: | JOINT, REGISTRATION |
| Парткод: | FC8-6384-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-6412-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0307-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC8-6399-000 |
| Деталь: | ARM, PLATEN, FRONT |
| Парткод: | FC8-6373-000 |
| Деталь: | ARM, PLATEN, REAR |
| Парткод: | FC8-6374-000 |
| Деталь: | SPACER, READ, FRONT |
| Парткод: | FC8-6375-000 |
| Деталь: | SPACER, READ, REAR |
| Парткод: | FC8-6376-000 |
| Деталь: | ROLLER, WHITE |
| Парткод: | FC8-6398-000 |
| Деталь: | GUIDE, PLATEN, 1 |
| Парткод: | FL2-9939-000 |
| Деталь: | LINK, SOLENOID |
| Парткод: | FC8-6381-000 |
| Деталь: | DAMPER, REV. GUIDE RETAINING |
| Парткод: | FC8-6403-000 |
| Деталь: | SOLENOID |
| Парткод: | FK2-6871-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU8-0306-000 |
| Деталь: | PHOTO INTEUPTE, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | SEPARATION REVERSE GUIDE ASSY |
| Парткод: | FM0-1209-000 |
| Деталь: | PAD, SEPARATION |
| Парткод: | FL3-5538-010 |
| Цена: | 1 400 ₽ |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2657-000 |
| Деталь: | LED PCB UNIT |
| Парткод: | FM4-8146-000 |
| Деталь: | LABEL, JAM CLEARING OPERATION |
| Парткод: | FS9-0204-000 |
| Деталь: | LABEL, GREEN |
| Парткод: | FS9-0205-000 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-0702-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | BUSHING |
| Парткод: | FU5-1172-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1626-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1088-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1089-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2658-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2659-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2660-000 |
| Деталь: | GEAR PULLEY, 27T/22T |
| Парткод: | FU8-0303-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0305-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0308-000 |
| Деталь: | GEAR PULLEY, 36T/54T/28T |
| Парткод: | FU8-0309-000 |
| Деталь: | PULLEY, 36T |
| Парткод: | FU8-0310-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0312-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0313-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU8-0314-000 |
| Деталь: | GEAR, 39T |
| Парткод: | FU8-0315-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU8-0316-000 |
| Деталь: | GEAR, 32T |
| Парткод: | FU8-0317-000 |
| Деталь: | GEAR, 48T/62T |
| Парткод: | FU8-0318-000 |
| Деталь: | SCREW,RS,M3X6.5 |
| Парткод: | XA9-1164-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1607-640 |
| Деталь: | SHEET, CLEANING, LARGE |
| Парткод: | FC8-6356-000 |
| Деталь: | SHEET, CLEANING, SMALL |
| Парткод: | FC8-6357-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-122 |
| Деталь: | PAPER FEED ASSEMBLY |
| Парткод: | FM4-8976-000 |
| Деталь: | MOTOR, DC |
| Парткод: | FK2-7326-000 |
| Деталь: | PULLEY, 53T/GEAR, 16T |
| Парткод: | FU7-0353-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1607-340 |
| Деталь: | PAPER PICK-UP DRIVE ASSEMBLY |
| Парткод: | FM4-7922-000 |
| Деталь: | COVER, TRAY, LOWER |
| Парткод: | FL3-2450-000 |
| Деталь: | GUIDE, TRAY, FRONT |
| Парткод: | FL3-2451-000 |
| Деталь: | RACK, TRAY |
| Парткод: | FC9-4983-000 |
| Деталь: | HOLDER, TRAY VOLUME |
| Парткод: | FC8-6338-000 |
| Деталь: | LEVER, TRAY SENSOR |
| Парткод: | FC8-6339-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FU7-8133-000 |
| Деталь: | GEAR, 50T |
| Парткод: | FC9-4984-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | TRAY, DOCUMENT |
| Парткод: | FL3-2449-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC8-6341-000 |
| Деталь: | GUIDE, TRAY, REAR |
| Парткод: | FL3-2452-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FU7-8134-000 |
| Деталь: | VARIABLE RESISTOR UNIT |
| Парткод: | FG3-3757-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | RACK, TRAY |
| Парткод: | FC8-6340-000 |
| Деталь: | DOCUMENT TRAY ASSEMBLY |
| Парткод: | FM4-8978-000 |
| Деталь: | COVER, HEATER CONNECTOR |
| Парткод: | FC9-4691-000 |
| Деталь: | CASSETTE HEATER ASSEMBLY |
| Парткод: | FM0-4834-000 |
| Деталь: | LABEL, HIGH TMP. CAUTION |
| Парткод: | FU6-8647-000 |
| Деталь: | HOLDER, SWITCH |
| Парткод: | FC8-2478-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2332-000 |
| Деталь: | SWITCH, DETECT PUSH |
| Парткод: | WC2-5680-000 |
| Деталь: | ROLLER, RAIL |
| Парткод: | FC8-4999-000 |
| Деталь: | RAIL, ROLLER SHAFT PLATE, LEFT |
| Парткод: | FL3-1456-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, 10P, W |
| Парткод: | VS1-7173-010 |
| Деталь: | CABLE, CASSETTE HEATER |
| Парткод: | FM4-7640-000 |
| Деталь: | CABLE, CASSETTE |
| Парткод: | FM4-7686-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | IC, MB87Q1911, ASIC |
| Парткод: | FK2-7574-000 |
| Деталь: | READER CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-C860-000 |
| Деталь: | FLANGE, BELT |
| Парткод: | FC5-4353-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FC6-8973-000 |
| Деталь: | GUIDE, PLATEN, 2 |
| Парткод: | FC8-6368-000 |
| Деталь: | FLAPPER, REVERSE |
| Парткод: | FL2-9949-000 |
| Деталь: | LEVER, READ SENSOR |
| Парткод: | FC8-6371-000 |
| Деталь: | LEVER, PAPER DELIVERY SENSOR |
| Парткод: | FC8-6372-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FC8-6377-000 |
| Деталь: | DUCT, HARNESS |
| Парткод: | FC8-6378-020 |
| Деталь: | FLANGE, PULLEY |
| Парткод: | FC8-6379-000 |
| Деталь: | CLIP |
| Парткод: | FC8-6380-000 |
| Деталь: | ROLLER, BELT TENSION |
| Парткод: | FC8-6382-000 |
| Деталь: | JOINT, DELIVERY GEAR |
| Парткод: | FC8-6385-000 |
| Деталь: | DIAL, JAM |
| Парткод: | FC0-4616-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6395-010 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FC8-6396-000 |
| Деталь: | ROLLER, READ |
| Парткод: | FC0-4619-000 |
| Деталь: | JOINT, READ PULLEY |
| Парткод: | FC8-6418-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FC8-6421-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FM1-F816-000 |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | FK2-6870-000 |
| Деталь: | FLAG, REGISTRATION SENSOR |
| Парткод: | FL2-9937-000 |
| Деталь: | BEARING, BALL, MF128ZZ |
| Парткод: | XG9-0507-000 |
| Деталь: | JOINT, PICK-UP |
| Парткод: | FC8-6383-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-6411-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0304-000 |
| Деталь: | JOINT, REGISTRATION |
| Парткод: | FC8-6384-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-6412-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0307-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC8-6399-000 |
| Деталь: | ARM, PLATEN, FRONT |
| Парткод: | FC8-6373-000 |
| Деталь: | ARM, PLATEN, REAR |
| Парткод: | FC8-6374-000 |
| Деталь: | SPACER, READ, FRONT |
| Парткод: | FC8-6375-000 |
| Деталь: | SPACER, READ, REAR |
| Парткод: | FC8-6376-000 |
| Деталь: | ROLLER, WHITE |
| Парткод: | FC8-6398-000 |
| Деталь: | GUIDE, PLATEN, 1 |
| Парткод: | FL2-9939-000 |
| Деталь: | LINK, SOLENOID |
| Парткод: | FC8-6381-000 |
| Деталь: | DAMPER, REV. GUIDE RETAINING |
| Парткод: | FC8-6403-000 |
| Деталь: | SOLENOID |
| Парткод: | FK2-6871-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU8-0306-000 |
| Деталь: | PHOTO INTEUPTE, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | SEPARATION REVERSE GUIDE ASSY |
| Парткод: | FM0-1209-000 |
| Деталь: | PAD, SEPARATION |
| Парткод: | FL3-5538-010 |
| Цена: | 1 400 ₽ |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2657-000 |
| Деталь: | LED PCB UNIT |
| Парткод: | FM4-8146-000 |
| Деталь: | LABEL, JAM CLEARING OPERATION |
| Парткод: | FS9-0204-000 |
| Деталь: | LABEL, GREEN |
| Парткод: | FS9-0205-000 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-0702-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | BUSHING |
| Парткод: | FU5-1172-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1626-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1088-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1089-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2658-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2659-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2660-000 |
| Деталь: | GEAR PULLEY, 27T/22T |
| Парткод: | FU8-0303-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0305-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0308-000 |
| Деталь: | GEAR PULLEY, 36T/54T/28T |
| Парткод: | FU8-0309-000 |
| Деталь: | PULLEY, 36T |
| Парткод: | FU8-0310-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0312-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0313-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU8-0314-000 |
| Деталь: | GEAR, 39T |
| Парткод: | FU8-0315-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU8-0316-000 |
| Деталь: | GEAR, 32T |
| Парткод: | FU8-0317-000 |
| Деталь: | GEAR, 48T/62T |
| Парткод: | FU8-0318-000 |
| Деталь: | SCREW,RS,M3X6.5 |
| Парткод: | XA9-1164-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1607-640 |
| Деталь: | SHEET, CLEANING, LARGE |
| Парткод: | FC8-6356-000 |
| Деталь: | SHEET, CLEANING, SMALL |
| Парткод: | FC8-6357-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-122 |
| Деталь: | PAPER FEED ASSEMBLY |
| Парткод: | FM4-8976-000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FE3-4753-000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FE3-4754-000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FE3-4755-000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FC0-4665-000 |
| Деталь: | LABEL, PAPER SET INSTRUCTION |
| Парткод: | FC0-4669-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FC0-4670-000 |
| Деталь: | HINGE, MULTI PICK-UP, REAR |
| Парткод: | FC0-2608-000 |
| Деталь: | STOPPER |
| Парткод: | FC0-2611-000 |
| Деталь: | FLAG, MULTI PAPER SENSOR |
| Парткод: | FC0-5222-000 |
| Деталь: | ROLLER, EXTRACTION |
| Парткод: | FC9-0670-000 |
| Деталь: | CAP, SHAFT CONDUCTIVE |
| Парткод: | FC9-0671-000 |
| Деталь: | COVER, MULTI SENSOR |
| Парткод: | FC9-0672-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-0923-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-1026-000 |
| Деталь: | SOLENOID |
| Парткод: | FK2-1410-000 |
| Деталь: | GUIDE, MULTI, UPPER |
| Парткод: | FL3-1348-010 |
| Деталь: | ROLLER, MULTI EXTRACTION DRIVE |
| Парткод: | FL3-1349-000 |
| Деталь: | GUIDE, MULTI LOWER |
| Парткод: | FL0-2517-000 |
| Деталь: | GUIDE, VERTICAL PATH |
| Парткод: | FL3-5605-000 |
| Деталь: | MULTI SEPARATION PAD ASSEMBLY |
| Парткод: | FM3-9287-010 |
| Деталь: | BUSHING |
| Парткод: | FC9-0684-000 |
| Деталь: | BUSHING ROLLER, |
| Парткод: | FC9-0685-000 |
| Деталь: | MULTI CAM, MULTI, |
| Парткод: | FC9-0687-000 |
| Деталь: | FRONT CAM, MULTI, |
| Парткод: | FC9-0688-000 |
| Деталь: | REAR |
| Парткод: | FC9-0689-000 |
| Деталь: | MULTI PAPER PICK-UP GEAR ASSY |
| Парткод: | FM3-9293-000 |
| Деталь: | PLATE, PAPER SIDE END, FRONT |
| Парткод: | FC0-2603-000 |
| Деталь: | PLATE, PAPER SIDE END, REAR |
| Парткод: | FC0-2604-000 |
| Деталь: | RACK, PAPER SIDE END |
| Парткод: | FC0-2605-000 |
| Деталь: | GEAR, 54T/18T |
| Парткод: | FC0-2606-000 |
| Деталь: | COVER, CABLE |
| Парткод: | FC0-2607-000 |
| Деталь: | HINGE, MULTI PICK-UP, FRONT |
| Парткод: | FC0-2609-000 |
| Деталь: | COVER, HINGE |
| Парткод: | FC0-2610-000 |
| Деталь: | MULTI FEED SIZE PCB ASSEMBLY |
| Парткод: | FM2-2768-000 |
| Деталь: | SCREW, B, M4X8 |
| Парткод: | XA9-1523-000 |
| Деталь: | TRAY, MULTI EXTENSION, 1 |
| Парткод: | FC0-2525-000 |
| Деталь: | TRAY, MULTI EXTENSION, 2 |
| Парткод: | FC0-2526-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2925-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2926-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2971-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2974-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU8-0525-000 |
| Деталь: | GEAR 27T/25T |
| Парткод: | FU8-0526-000 |
| Деталь: | GEAR, 19T |
| Парткод: | FU8-0527-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2804-000 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | PAD, SEPARATION |
| Парткод: | FL3-3469-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL3-1352-000 |
| Цена: | 700 ₽ |
| Деталь: | CONNECTOR, 2P |
| Парткод: | VS1-7507-002 |
| Деталь: | COVER, MULTI |
| Парткод: | FC0-2527-000 |
| Деталь: | MULTI PAPER PICK-UP ASSEMBLY |
| Парткод: | FM4-7333-010 |
| Деталь: | BUSHING |
| Парткод: | FA9-4041-005 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FC0-3063-000 |
| Деталь: | HOLDER, FIXING PAPER DELIVERY |
| Парткод: | FC0-3074-000 |
| Деталь: | ROLLER, FIXING PAPER DELIVERY |
| Парткод: | FC0-3077-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FC0-8273-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FL3-6225-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU9-0319-000 |
| Деталь: | GEAR, 18T/26T |
| Парткод: | FU9-0320-000 |
| Деталь: | GEAR, 15T |
| Парткод: | FU9-0321-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0325-000 |
| Деталь: | SCREW, FIXED, M4 |
| Парткод: | FE2-0464-000 |
| Деталь: | COLLAR, FIXING DELIVERY |
| Парткод: | FC9-7720-000 |
| Деталь: | SPRING, RETAINING |
| Парткод: | FU7-2934-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-1672-000 |
| Деталь: | BUSHING |
| Парткод: | FE2-0508-000 |
| Деталь: | DELIVERY LOWER GUIDE UNIT |
| Парткод: | FM4-7293-000 |
| Деталь: | LABEL, DIAL OPERATION |
| Парткод: | FS9-0203-000 |
| Деталь: | LABEL, HINGE CAUTION |
| Парткод: | FU7-8223-000 |
| Деталь: | LABEL, HINGE CAUTION, C |
| Парткод: | FU7-8452-000 |
| Деталь: | COVER, STAMP |
| Парткод: | FC8-6311-000 |
| Деталь: | LEVER, READ 1 ESTRANGEMENT |
| Парткод: | FC8-6330-000 |
| Деталь: | HOLDER, TRAY SUPPORT |
| Парткод: | FC8-6387-000 |
| Деталь: | HOLDER, FEEDER SHAFT |
| Парткод: | FC8-6388-000 |
| Деталь: | SHEET, READ 2 LEAD |
| Парткод: | FC8-6405-000 |
| Деталь: | HINGE, LEFT |
| Парткод: | FC8-6420-000 |
| Деталь: | SCREW,RS,M4 |
| Парткод: | XA9-0732-010 |
| Деталь: | FAN |
| Парткод: | FK2-6873-000 |
| Деталь: | COVER, COPYBOARD |
| Парткод: | FL2-9945-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FL3-2934-010 |
| Деталь: | COVER, REAR |
| Парткод: | FL3-2935-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1173-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2651-000 |
| Деталь: | CABLE, INTERFACE |
| Парткод: | FM4-8149-000 |
| Деталь: | LABEL, PROHIBITION DOCUMENT |
| Парткод: | FU7-8444-000 |
| Деталь: | LABEL, PROHIBITION DOCUMENT |
| Парткод: | FU7-8446-000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FU7-8449-000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FU7-8447-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | ADF PCB ASSEMBLY |
| Парткод: | FM4-8145-000 |
| Деталь: | RIGHT HINGE ASSEMBLY |
| Парткод: | FM3-6893-000 |
| Деталь: | LABEL, HINGE CAUTION, C |
| Парткод: | FU7-8454-000 |
| Деталь: | LABEL, HINGE CAUTION |
| Парткод: | FU7-8455-000 |
| Деталь: | LABEL, HINGE CAUTION, C |
| Парткод: | FU7-8453-000 |
| Деталь: | LABEL, HINGE CAUTION, A |
| Парткод: | FU7-8225-000 |
| Деталь: | LABEL, HINGE CAUTION |
| Парткод: | FU7-8226-000 |
| Деталь: | LABEL, HINGE CAUTION |
| Парткод: | FU7-8142-000 |
| Деталь: | CABLE, BASE |
| Парткод: | FM4-8150-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6961-000 |
| Деталь: | STAMPER |
| Парткод: | FB5-9410-000 |
| Деталь: | SOLENOID |
| Парткод: | FK2-0216-000 |
| Деталь: | ADF MAIN BODY (ADF MODEL) |
| Парткод: | NPN |
| Деталь: | SHUTTER, FRONT |
| Парткод: | FC9-0733-000 |
| Деталь: | SHUTTER, REAR |
| Парткод: | FC9-0734-000 |
| Деталь: | PINION, 18T |
| Парткод: | FC9-1683-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK2-9148-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, 7P |
| Парткод: | VS1-7173-007 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | IC PHOTOINTERRUPTER, HYBRID |
| Парткод: | WG8-5836-000 |
| Деталь: | CABLE, SIDE END SHUTTER |
| Парткод: | FM4-2950-000 |
| Деталь: | CARTRIDGE RIGHT RAIL ASSEMBLY |
| Парткод: | NPN |
| Деталь: | ROLLER, REGISTRATION, 1 |
| Парткод: | FC5-4323-000 |
| Деталь: | ROLLER, REGISTRATION, 2 |
| Парткод: | FC5-4324-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | CASE, LED |
| Парткод: | FC8-6345-000 |
| Деталь: | KNOB, PAPER PICK-UP COVER |
| Парткод: | FC9-6190-000 |
| Деталь: | LEVER, EMPTY SENSOR |
| Парткод: | FC8-6347-010 |
| Деталь: | LEVER, TIMING SENSOR |
| Парткод: | FC8-6348-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU8-0302-000 |
| Деталь: | SHUTTER |
| Парткод: | FL2-9948-000 |
| Деталь: | COVER, PAPER PICK-UP |
| Парткод: | FL3-2940-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2656-000 |
| Деталь: | GUIDE, PAPER PICK-UP, LOWER |
| Парткод: | FL3-5998-000 |
| Деталь: | PAPER PICK-UP ROLLER UNIT |
| Парткод: | FM3-6892-010 |
| Цена: | 7 500 ₽ |
| Деталь: | ROLLER, PAPER SEPARATION |
| Парткод: | FC6-2784-000 |
| Деталь: | LEVER, STOP |
| Парткод: | FC6-8971-010 |
| Деталь: | ARM, PICK, FRONT |
| Парткод: | FC8-6351-000 |
| Деталь: | ARM, PICK, REAR |
| Парткод: | FC8-6352-010 |
| Деталь: | JOINT |
| Парткод: | FC8-6353-000 |
| Деталь: | ROLLER, PICK-UP |
| Парткод: | FC8-6355-000 |
| Цена: | 700 ₽ |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-6410-010 |
| Деталь: | GEAR, 20T |
| Парткод: | FU8-0299-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0300-000 |
| Деталь: | GEAR, 33T |
| Парткод: | FU8-0301-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1172-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1626-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2654-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2655-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD3-2200-102 |
| Деталь: | PAPER PICK-UP COVER ASSEMBLY |
| Парткод: | FM0-1208-000 |
| Деталь: | WASTE TONER BOX ASSEMBLY |
| Парткод: | FM3-9276-020 |
| Деталь: | BUSHING |
| Парткод: | FA9-4077-000 |
| Деталь: | ROLLER, PAPER DELIVERY DRIVEN |
| Парткод: | FC0-3064-000 |
| Деталь: | HOLDER, BUSHING |
| Парткод: | FC0-3066-000 |
| Деталь: | HOLDER, BUSHING |
| Парткод: | FC0-3067-000 |
| Деталь: | HOLDER, BUSHING |
| Парткод: | FC0-3068-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-8277-000 |
| Деталь: | ROLLER, SLEEVE |
| Парткод: | FL2-5277-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU5-2683-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2787-000 |
| Деталь: | DELIVERY UPPER GUIDE ASSEMBLY |
| Парткод: | FM4-7295-000 |
| Деталь: | COVER, FRONT, UPPER |
| Парткод: | FC0-2470-000 |
| Деталь: | PANEL, RIGHT LOWER, FRONT |
| Парткод: | FC0-2471-000 |
| Деталь: | PANEL, RIGHT LOWER, REAR |
| Парткод: | FC0-2472-000 |
| Деталь: | PANEL, LEFT |
| Парткод: | FC0-2473-000 |
| Деталь: | PANEL, LEFT LOWER |
| Парткод: | FC0-2474-000 |
| Деталь: | COVER, PAPER DELIVERY, REAR |
| Парткод: | FC0-2476-000 |
| Деталь: | PANEL, REAR |
| Парткод: | FC0-2477-000 |
| Деталь: | PANEL, LEFT REAR |
| Парткод: | FC0-2478-000 |
| Деталь: | PANEL, REAR LOWER |
| Парткод: | FC0-2482-000 |
| Деталь: | PANEL, PROTECTIVE |
| Парткод: | FC0-2484-000 |
| Деталь: | PANEL, DELIVERY TRAY AUXILIARY |
| Парткод: | FC0-2485-000 |
| Деталь: | PANEL, INNER RIGHT FRONT |
| Парткод: | FC0-2486-000 |
| Деталь: | PANEL, DELIVERY TRAY AUXILIARY |
| Парткод: | FC0-2592-000 |
| Деталь: | JOINT, PAPER DELIVERY COVER |
| Парткод: | FC0-2593-010 |
| Деталь: | PANEL, HANDLE |
| Парткод: | FC0-4674-000 |
| Деталь: | TRAY, PAPER DELIVERY, 2 |
| Парткод: | FC0-4675-000 |
| Деталь: | PANEL, PAPER DELIVERY, LOWER |
| Парткод: | FC0-4676-000 |
| Деталь: | TRAY, PAPER DELIVERY, 1 |
| Парткод: | FC0-4677-000 |
| Деталь: | COVER, MAIN SWITCH |
| Парткод: | FC8-4000-000 |
| Деталь: | LABEL, WASTE TONER CHANGE, UP. |
| Парткод: | FC9-0573-000 |
| Деталь: | PANEL, RIGHT CENTER |
| Парткод: | FC0-4693-000 |
| Деталь: | LABEL, WASTE TONER CHANGE, LW. |
| Парткод: | FC9-7281-000 |
| Деталь: | LABEL, MAIN POWER SUPPLY |
| Парткод: | FC9-7862-000 |
| Деталь: | LABEL, MAIN POWER SUPPLY |
| Парткод: | FC9-7863-000 |
| Деталь: | LABEL, MAIN POWER SUPPLY |
| Парткод: | FC9-7861-000 |
| Деталь: | EMBLEM |
| Парткод: | FL3-1185-000 |
| Деталь: | COVER, PAPER DELIVERY, REAR |
| Парткод: | FL3-6200-000 |
| Деталь: | PANEL, RIGHT REAR |
| Парткод: | FC0-2479-000 |
| Деталь: | COVER, RIGHT REAR, SMALL |
| Парткод: | FC0-2481-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FC8-8346-000 |
| Деталь: | LABEL, TONER |
| Парткод: | FC0-5223-000 |
| Деталь: | LABEL, TONER |
| Парткод: | FC0-5224-000 |
| Деталь: | LABEL, TONER |
| Парткод: | FC0-5225-000 |
| Деталь: | LABEL, TONER |
| Парткод: | FC0-5226-000 |
| Деталь: | LABEL, TONER |
| Парткод: | FC0-5227-000 |
| Деталь: | LABEL, TONER |
| Парткод: | FC0-5228-000 |
| Деталь: | MOUNT, SWITCH COVER |
| Парткод: | FC0-2538-000 |
| Деталь: | SCREW, RS, M3X8.5 |
| Парткод: | XA9-1567-000 |
| Деталь: | FRONT DOOR UNIT |
| Парткод: | FM4-9156-000 |
| Деталь: | HOLDER, SERVICE BOOK |
| Парткод: | FC9-9069-000 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FC9-7297-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FC0-2468-000 |
| Деталь: | LABEL, FAX |
| Парткод: | FC0-5250-000 |
| Деталь: | LABEL, GROUNDING CAUTION |
| Парткод: | FU5-8901-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | PULLEY, 80T |
| Парткод: | FC5-1516-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK2-7327-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1609-040 |
| Деталь: | PAPER PICK-UP DRIVE ASSY |
| Парткод: | FM4-7923-000 |
Коды ошибок
E000-0001
E001-0000
E001-0001
E001-0002
E002-0000
E003-0000
E004-0000
E010-0001
E010-0002
E014-0001
E014-0002
E020-0000
E024-0000
E024-0001
E025-0000
E025-0001
E032-0001
E110-0001
E110-0002
E110-0003
E196-0000
E196-0001
E196-0002
E197-0000
E197-0001
E202-0001
E202-0002
E225-0000
E227-0001
E227-0002
E227-0003
E227-0004
E240-0000
E240-0001
E246-0001
E246-0002
E246-0003
E247-0001
E247-0002
E247-0003
E247-0004
E248-0001
E248-0002
E248-0003
E261-0000
E280-0003
E315-0007
E315-000d
E315-000e
E315-0025
E315-0027
E315-0033
E315-0035
E315-0100
E315-0500
E315-0501
E315-0510
E315-0511
E315-0520
E315-0521
E315-0530
E315-0531
E315-0540
E315-0541
E315-0550
E315-0551
E315-0560
E315-0561
E350-0000
E350-0001
E350-0002
E350-0003
E350-3000
E351-0000
E354-0001
E354-0002
E355-0001
E355-0003
E355-0004
E400-0001
E400-0002
E400-0003
E413-0001
E413-0002
E490-0001
E500-0000
E500-0001
E503-0002
E503-0003
E505-0001
E505-0002
E514-8001
E514-8002
E520-0001
E520-0002
E530-8001
E530-8002
E531-8001
E531-8002
E532-0001
E532-0002
E532-8001
E532-8002
E535-8002
E537-8001
E537-8002
E540-0001
E540-0005
E540-8001
E540-8002
E540-8003
E540-8004
E540-8005
E540-8006
E540-8007
E542-0001
E542-0002
E542-8001
E542-8002
E542-8004
E542-8005
E542-8006
E542-8007
E551-0001
E551-0002
E567-0001
E567-0002
E56F-0001
E56F-0002
E571-0001
E571-0002
E575-0001
E575-0002
E584-0002
E584-8001
E590-8001
E590-8002
E591-8001
E591-8002
E592-8001
E592-8002
E592 8003
E592-8004
E592-8005
E592-8006
E592-8007
E592-8008
E592-8009
E592-800A
E593-8001
E593-8002
E5F0-8001
E5F0-8002
E5F1-8001
E5F1-8002
E5F2-8001
E5F2-8002
E5F3-8001
E5F3-8002
E5F4-8001
E5F4-8002
E5F5-8001
E5F5-8002
E5F6-8001
E5F6-8002
E5F6-8003
E5F6-8004
E5F6-8005
E602
E604-0000
E609-0008
E609-0009
E610
E611-0000
E615-0001
E674
E677-0001
E677-0003
E677-0004
E677-0010
E677-0080
E710-0001
E711-0001
E711-0002
E713-0000
E713-0001
E713-0002
E713-0004
E713-0010
E713-0011
E713-0020
E713-0021
E713-0022
E716-0000
E717-0001
E717-0002
E719-0001
E719-0002
E719-0011
E719-0012
E719-0031
E719-0032
E730-1001
E730-100A
E730-9004
E730-9005
E730-A006
E730-A007
E730-B013
E732-0000
E732-0001
E732-0010
E732-0021
E732-8888
E732-9999
E733-0000
E733-0001
E733-0002
E733-0010
E740-0002
E743-0000
E744
E746
E748
E753-0001
E760-0001
E800-0000
E804-0000
E804-0001
E805-0000
E805-0001
E805-0002
E805-0003
E806-0000
E806-0001
E806-0002
E806-0003
E840-0000
E840-0001
E840-0002
E840-0003
E840-0004
E880-0001
E880-0005
Описание
| Error code: | E000-0001 |
| Description: | Fixing fault |
| Causes: | After the fixing heater has gone on, the reading of the main thermistor is not 50 deg C within about 1.5 sec. Cause The fixing film unit is faulty. The engine controller PCB is faulty. |
| Remedy: | - Replace the fixing film unit. - Replace the engine controller PCB. |
| Error code: | E001-0000 |
| Description: | Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature 235 deg C) during temperature control |
| Causes: | The main thermistor detected a temperature of higher than 255 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0001 |
| Description: | Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control. |
| Causes: | The sub thermistor detected a temperature of higher than 290 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0002 |
| Description: | Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 1 has detected a high temperature (ASIC detection) |
| Causes: | The fixing film unit is faulty (i.e., the thermistor has a short circuit). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service move: COPIER>FUNCTION>CLEAR>ERR. |
| Remedy: | Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR. |
| Error code: | E002-0000 |
| Description: | Low temperature during temperature control. The target temperature is not reached during temperature control. |
| Causes: | The fixing film unit is faulty (i.e., the main thermistor TH1 has poor contact, or the fixing heater is faulty). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>FCLEAR>ERR. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0000 |
| Description: | Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E004-0000 |
| Description: | Fixing power supply drive circuit error |
| Causes: | 43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly. |
| Error code: | E010-0001 |
| Description: | Main motor error Lock of the motor fails to be detected 2 sec or more after the motor starts to operate. |
| Causes: | The main motor drive system has an excess load. The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Check on connection of the connector, Replace the motor |
| Error code: | E010-0002 |
| Description: | Main motor error After rotation of the motor becomes stable, the motor lock fails (i.e., the motor becomes unstable) for 500msec or more. |
| Causes: | The main motor drive system has an excess load. The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Check on connection of the connector, Replace the motor |
| Error code: | E014-0001 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E014-0002 |
| Description: | Fixing motor error When the lock was disengaged after the motor was locked |
| Causes: | The belt motor (M15) is faulty. The belt motor drive system has an excess load. The drum drive AC generation PCB is faulty. The transfer drive AC generation PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Replace the drumITB moter. Replace the fixing moter.Replace the DCDC converterAi38VAj. Replace the fixing belt unit. |
| Error code: | E020-0000 |
| Description: | Density sensor failure warning |
| Error code: | E024-0000 |
| Description: | Toner level sensor failure |
| Causes: | Failure output from the toner level sensor (Yellow). Cause Memory controller PCB assembly fault, DC controller PCB assembly fault, toner cartridge fault. |
| Remedy: | - Replace toner cartridge - Replace memory controller PCB - Replace DC controller PCB |
| Error code: | E024-0001 |
| Description: | Toner level sensor failure |
| Causes: | Failure output from the toner level sensor (Magenta). Cause Memory controller PCB assembly fault, DC controller PCB assembly fault, toner cartridge fault. |
| Remedy: | - Replace toner cartridge - Replace memory controller PCB - Replace DC controller PCB |
| Error code: | E025-0000 |
| Description: | Error in the toner motor Indicates an error of Y developing assembly toner supply |
| Remedy: | Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor |
| Error code: | E025-0001 |
| Description: | There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25). There is an overcurrent in the hopper stirring motor (M23). |
| Remedy: | Turn off and then on the main power. |
| Error code: | E032-0001 |
| Description: | NE controller counter operation failure When the counter function of the NE controller does not work |
| Causes: | The DA unit is faulty. The main controller PCB is faulty. |
| Remedy: | Check the cable connections. |
| Error code: | E110-0001 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor rotation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0002 |
| Description: | Error in first artificial BD adjustment |
| Causes: | Primary pseudo BD correction |
| Error code: | E110-0003 |
| Description: | There is a scanner motor error. The FG signal is not detected while the polygon scanner is rotating stably. |
| Remedy: | Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power. |
| Error code: | E196-0000 |
| Description: | Invalid RFU execution requested |
| Causes: | D-con update for the host machine or the optional cassette is not completed. |
| Error code: | E196-0001 |
| Description: | Image processor PCB failure Error on writing and readout ROM of image processor PCB (mainn ROM). |
| Causes: | D-con update for the optional cassette is not completed. |
| Remedy: | - Putting the switch on/off of the power supply. - Replace the image processor PCB. |
| Error code: | E196-0002 |
| Description: | Image processor PCB failure Error on writing and readout ROM of image processor PCB (option ROM). |
| Causes: | Can not access to DC controller NVRAM Cause Failure in DC controller PCB |
| Remedy: | - Putting the switch on/off of the power supply. - Replace the image processor PCB. |
| Error code: | E197-0000 |
| Description: | Printer engine communication error Erroneous communication between the DC controller PCB and image processor PCB was detected. |
| Causes: | Internal communication error |
| Remedy: | - Check the connectors of the DC controller PCB and image processor PCB. - Replace the DC controller PCB for normal connection. - Replace the image processor PCB. |
| Error code: | E197-0001 |
| Description: | Engine communication error |
| Causes: | Error between DC controller PCB and main controller PCB. Cause Failure in connection between PCB, failure in DC controller PCB, failure in controller PCB. |
| Remedy: | - Check the connection of the connector of the DC controller PCB and controller PCB - Replace the DC controller PCB - Replace the controller PCB |
| Error code: | E202-0001 |
| Description: | Reader HP sensor fault |
| Causes: | Reader HP outward fault The CCD unit moves backward, but does not move to the home position. |
| Remedy: | - Replace reader HP sensor. - Replace reader motor sensor. - Replace reader unit. |
| Error code: | E202-0002 |
| Description: | Contact Sensor HP error, Failure in return |
| Causes: | Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board. |
| Error code: | E225-0000 |
| Description: | Error in light intensity of the lamp |
| Causes: | Decrease of light intensity of the lamp. |
| Remedy: | Replace reader unit. |
| Error code: | E227-0001 |
| Description: | Reader unit power supply error When the 24 V port is OFF when the power is turned ON. |
| Remedy: | Disconnect and re-connect the power connector. Replace the power supply |
| Error code: | E227-0002 |
| Description: | Reader unit power supply error When the 24 V port is OFF when a job is started. |
| Remedy: | Disconnect and re-connect the power connector. Replace the power supply |
| Error code: | E227-0003 |
| Description: | Reader unit power supply error When the 24 V port is OFF when a job is finished. |
| Remedy: | Disconnect and re-connect the power connector. Replace the power supply |
| Error code: | E227-0004 |
| Description: | Reader unit power supply error When the 24 V port is OFF during load drive. |
| Remedy: | Disconnect and re-connect the power connector. Replace the power supply |
| Error code: | E240-0000 |
| Description: | Error in communication between main controller and DC controller Serial communication error |
| Causes: | The main controller PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Check the connector connections. Check the DC controller PCB (MAISY). Replace the No.1 main controller circuit. |
| Error code: | E240-0001 |
| Description: | Error in communication of controller There is no response when 3 sec passed since the main controller had sent the pickup request to DC controller during printing. |
| Remedy: | Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB |
| Error code: | E246-0001 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E246-0002 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E246-0003 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E247-0001 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E247-0002 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E247-0003 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E247-0004 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E248-0001 |
| Description: | EEPROM access error |
| Causes: | Error at EEPROM power-on EEPROM data cannot be read at power-on. |
| Remedy: | Replace reader unit. |
| Error code: | E248-0002 |
| Description: | EEPROM access error |
| Causes: | Error in EEPROM writing EEPROM writing cannot be performed. |
| Remedy: | Replace reader unit. |
| Error code: | E248-0003 |
| Description: | EEPROM access error |
| Causes: | Error in EEPROM reading after writing EEPROM reading cannot be performed after writing is performed. |
| Remedy: | Replace reader unit. |
| Error code: | E261-0000 |
| Description: | Zero-cross signal error If failed to detect zero-cross signal cycle of the power supply when initializing. When the input of the zero-signal failed continuously for three seconds while controlling the temperature adjustment. |
| Causes: | The wiring is faulty (short circuit, open circuit). The main power supply PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | - Replace the power supply PCB. - Replace the DC controller PCB. |
| Error code: | E280-0003 |
| Description: | Reading unit communication error Insufficient insertion of the reading unit connector |
| Remedy: | Disconnect and then connect the flexible cable. Replace the flexible cable |
| Error code: | E315-0007 |
| Description: | There is an error in image data. There is an error in JBIG encoding. |
| Remedy: | Turn off and then back on the power. |
| Error code: | E315-000d |
| Description: | There is an error in image data. There is an error in JBIG decoding. |
| Remedy: | Turn off and then back on the power. |
| Error code: | E315-000e |
| Description: | Image data trouble Damaged data (trouble in memory or HDD) Software decoding error |
| Remedy: | Replace the image memory (SDRAM) or HDD. |
| Error code: | E315-0025 |
| Description: | Abnormality of image data ASIC (for compression/decompression) on the image conversion PCB is faulty. Image data transfer error during rotation processing. |
| Remedy: | Check on connection of the image conversion board, Replace the image conversion board |
| Error code: | E315-0027 |
| Description: | There is an error in image data. Error in ROTU timeout |
| Remedy: | Replace SDRAM. Replace HDD. Replace the main controller PCB. |
| Error code: | E315-0033 |
| Description: | There is an error in image data. Error in MemFill hardware |
| Remedy: | Replace the main controller PCB. |
| Error code: | E315-0035 |
| Description: | There is an error in image data. Error in MemFill timeout |
| Remedy: | Replace the main controller PCB. |
| Error code: | E315-0100 |
| Description: | There is an error in image data. Error in PrcOverRun |
| Remedy: | Replace the main controller PCB. |
| Error code: | E315-0500 |
| Description: | There is an error in image data. Error in device timeout [location to be detected] image process module (SCIO) [Detection timing] when there is no interruption 2 min after the operation has been started |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0501 |
| Description: | There is an error in image data. Device: abnormal termination error [location to be detected] image process module (SCIO) [Detection timing] When abnormal interruption is detected after the operation has been started. |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0510 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (SCIP) [Detection timing] when there is no interruption 2 min after the operation has been started. |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0511 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (SCIP) [Detection timing] when abnormal interruption is detected after the operation has been detected |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0520 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (CMIP) [Detection timing] When there is no interruption 2 min after the operation has been started |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0521 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (CMIP) [Detection timing] when abnormal interruption is detected after the operation has been detected |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB |
| Error code: | E315-0530 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (JPEN) [Detection timing] when there is no interruption 2 min after the operation has been started. |
| Remedy: | Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently. |
| Error code: | E315-0531 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (JPEN) [Detection timing] when abnormal interruption is detected after the operation has been started. |
| Remedy: | Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently. |
| Error code: | E315-0540 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (JPDE) [Detection timing] when there is no interruption 2 min after the operation has been started. |
| Remedy: | Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently. |
| Error code: | E315-0541 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (JPDE) [Detection timing] when abnormal interruption is detected after the operation has been started |
| Remedy: | Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently. |
| Error code: | E315-0550 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (PRIP) [Detection timing] when there is no interruption 2 min after the operation has been started. |
| Remedy: | Check connection with DDI-P cable(DCON). Replace the main controller PCB. |
| Error code: | E315-0551 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (PRIP) [Detection timing] when abnormal interruption is detected after the operation has been started. |
| Remedy: | Check connection with DDI-P cable(DCON). Replace the main controller PCB. |
| Error code: | E315-0560 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (PRIO) [Detection timing] when there is no interruption 2 min after the operation has been started. |
| Remedy: | Check connection with DDI-P cable(DCON). Replace the main controller PCB. |
| Error code: | E315-0561 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (PRIO) [Detection timing] when abnormal interruption is detected after the operation has been started. |
| Remedy: | Check connection with DDI-P cable(DCON). Replace the main controller PCB. |
| Error code: | E350-0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E350-0001 |
| Description: | Fault in the soft ID PCB/function An error has occurred in the course of full data read operation on the soft ID PCB. |
| Remedy: | Turn off the main power, and check the connection of the soft ID PCB. If the remedy fails, replace the soft ID PCB. |
| Error code: | E350-0002 |
| Description: | Fault in the soft ID PCB/function The value of the check sum area of all data read from the soft ID PCB and the result of checksum computation do not match. |
| Remedy: | Turn off the main power, and replace the soft ID PCB. If the remedy fails, replace the soft ID PCB. |
| Error code: | E350-0003 |
| Description: | Fault in the soft ID PCB/function The values in the soft ID check sum area of FRAM, SRAM1, and SRAM2 and the result of a check sum computation differ. |
| Remedy: | Turn off the main power, and check the connection of the soft ID PCB. If the remedy fails, replace the soft ID PCB. |
| Error code: | E350-3000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E351-0000 |
| Description: | Main controller PCB fault |
| Causes: | Internal error of the main controller PCB Cause Main controller PCB fault. |
| Remedy: | - Check the connection of main controller PCB. - Replace main controller PCB. |
| Error code: | E354-0001 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E354-0002 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E355-0001 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E355-0003 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E355-0004 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E400-0001 |
| Description: | Feeder communication error Checksum error |
| Remedy: | Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub). |
| Error code: | E400-0002 |
| Description: | Feeder communication error Reception status error |
| Remedy: | Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub). |
| Error code: | E400-0003 |
| Description: | Feeder communication error Reception interrupt error |
| Remedy: | Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub). |
| Error code: | E413-0001 |
| Description: | Pressure motor trouble Pressure HP sensor OPEN |
| Remedy: | Replace the pressure motor. |
| Error code: | E413-0002 |
| Description: | Pressure motor trouble Pressure HP sensor CLOSE |
| Remedy: | Replace the pressure motor. |
| Error code: | E490-0001 |
| Description: | Wrong model error When the feeder of another model has been detected |
| Remedy: | Connect the feeder for this unit. |
| Error code: | E500-0000 |
| Description: | The communication between the copier and the finisher is disrupted and is not corrected for 5 sec or less |
| Causes: | The copier harness is faulty. (disconnected connector, open circuit) The finisher controller PCB or the copier’s DC controller PCB is faulty. |
| Error code: | E500-0001 |
| Description: | Finisher communication error Data communication could not be performed normally. It has been retried three times in vain. |
| Remedy: | - Check the connectors of the finisher controller PCB and DC controller PCB for normal connection. - Replace the finisher controller PCB. - Replace the DC controller PCB. |
| Error code: | E503-0002 |
| Description: | Saddle communication error When communication with the saddle stitcher is interrupted |
| Remedy: | - Check the connections between the saddle stitcher controller PCB and finisher controller PCB. - Replace the saddle stitcher controller PCB and finisher controller PCB. |
| Error code: | E503-0003 |
| Description: | There is an error in the communication within the finisher (finisher R1/R2). finisher-to-punch unit communication error |
| Causes: | A communication error has been detected. |
| Remedy: | Check the connection between the Punch controller PCB and the finisher controller PCB. |
| Error code: | E505-0001 |
| Description: | Finisher backup memory error When the checksum value calculated by the CPU differs from the checksum values of the data held inside the RAM |
| Causes: | The backup RAM is faulty. |
| Remedy: | Replace the finisher controller PCB. |
| Error code: | E505-0002 |
| Description: | Finisher backup memory error When the verify processing is not completed even after 2000 ms have elapsed during data writing |
| Causes: | The EEPROM is faulty. The finisher controller PCB is faulty. The puncher driver PCB is faulty. |
| Remedy: | Replace the finisher controller PCB. |
| Error code: | E514-8001 |
| Description: | Bundling (forward rotation direction) error When the trailing edge fails to leave the trailing edge assist home position even when the trailing edge assist motor has been driven for 3 sec. |
| Remedy: | Replace the trailing edge assist motor (M109) and trailing edge assist home position sensor (PI109). |
| Error code: | E514-8002 |
| Description: | Bundling (forward rotation direction) error When the trailing edge fails to return to the trailing edge assist home position even when the trailing edge assist motor has been driven for 3 sec. |
| Remedy: | Replace the trailing edge assist motor (M109) and trailing edge assist home position sensor (PI109). |
| Error code: | E520-0001 |
| Description: | - Offset motor or finisher controller PCB failure - Offset HP sensor failure - The offset motor was driven for 1000 ms in the HP sensor approach direction, but the offset HP sensor did not turn on. |
| Remedy: | - Check the connector of the offset HP sensor. - Check the connector of the offset motor. - Replace the offset HP sensor. - Replace the offset motor. - Replace the finisher controller PCB. |
| Error code: | E520-0002 |
| Description: | - Offset motor or finisher controller PCB failure - Offset HP sensor failure - The offset motor was driven for 1000 ms in the HP sensor escape direction, but the offset HP sensor did not turn off. |
| Remedy: | - Check the connector of the offset HP sensor. - Check the connector of the offset motor. - Replace the offset HP sensor. - Replace the offset motor. - Replace the finisher controller PCB. |
| Error code: | E530-8001 |
| Description: | Alignment error When the alignment plate fails to leave the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec. |
| Remedy: | Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106). |
| Error code: | E530-8002 |
| Description: | Alignment error When the alignment plate fails to return to the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec. |
| Remedy: | Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106). |
| Error code: | E531-8001 |
| Description: | Stapler error When the stapler fails to leave the stapler home position even though the stapler motor was driven for 0.5 sec. |
| Remedy: | Replace the stapler motor (M111) and stapler home position detection sensor (PI50). |
| Error code: | E531-8002 |
| Description: | Stapler error When the stapler fails to return to the stapler home position even though the stapler motor was driven for 0.5 sec. |
| Remedy: | Replace the stapler motor (M111) and stapler home position detection sensor (PI50). |
| Error code: | E532-0001 |
| Description: | There is a fault in the shift of the stapler. Finisher-N1/Saddle Finisher-N2 The stapler shift motor (M4) or the stapler shift home position sensor (PI7) is faulty. There is a fault in the path of the stapler shift base. The stapler shift base does not leave the stapler shift home position sensor when the stapler shift motor has been driven for 4 sec. |
| Causes: | The stapler shift motor (M4) is faulty. The stapler shift home position sensor (PI7) is faulty. |
| Remedy: | Replace the stapler shift HP sensor (PI50) , Replace the stapler shift motor (M35) |
| Error code: | E532-0002 |
| Description: | There is a fault in the shift of the stapler. Finisher-N1/Saddle Finisher-N2 The stapler shift motor (M4) or the stapler shift home position sensor (PI7) is faulty. There is a fault in the path of the stapler shift base. The stapler shift base does not return from the stapler shift home position sensor when the stapler shift motor has been driven for 4 sec. |
| Causes: | The stapler shift motor (M4) is faulty. The stapler shift home position sensor (PI7) is faulty. |
| Remedy: | Replace the stapler shift HP sensor (PI50) , Replace the stapler shift motor (M35) |
| Error code: | E532-8001 |
| Description: | There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go off within a specific period of time after the stapler shift motor has started to rotate. |
| Remedy: | 1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected? |
| Error code: | E532-8002 |
| Description: | There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go on within a specific period of time after the stapler shift motor has started to rotate. |
| Remedy: | 1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected? |
| Error code: | E535-8002 |
| Description: | Oscillation error Occurs when the oscillation guide close switch fails to be set to ON even when the oscillator motor is run in the reverse direction for 1 sec. |
| Remedy: | Replace the oscillator motor (M106) and oscillation home position sensor (PI105). |
| Error code: | E537-8001 |
| Description: | Front alignment error When the alignment plate fails to leave the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec. |
| Remedy: | Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107). |
| Error code: | E537-8002 |
| Description: | Front alignment error When the alignment plate fails to return to the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec. |
| Remedy: | Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107). |
| Error code: | E540-0001 |
| Description: | - Standard tray shift motor or finisher controller PCB failure - Standard tray HP sensor failure - Standard tray clock sensor failure - Standard tray shift motor load failure The standard tray was moved but the paper surface was not detected. |
| Causes: | The tray lift motor (M5) is faulty. The tray lift motor clock sensor 1/2 (PI19/PI20) is faulty. The tray home position sensor (PI8) is faulty. |
| Remedy: | - Check the connector of the standard tray HP sensor. - Check the connector of the standard tray clock sensor. - Check the connector of the standard tray shift motor. - Replace the standard tray HP sensor. - Replace the standard tray clock sensor. - Replace the standard tray shift motor. - Replace the finisher controller PCB. |
| Error code: | E540-0005 |
| Description: | - Standard tray shift motor or finisher controller PCB failure - Standard tray HP sensor failure - Standard tray clock sensor failure - Standard tray shift motor load failure The encoder clock signal was not detected two or more times when the standard tray was operated for 300 ms. |
| Remedy: | - Check the connector of the standard tray HP sensor. - Check the connector of the standard tray clock sensor. - Check the connector of the standard tray shift motor. - Replace the standard tray HP sensor. - Replace the standard tray clock sensor. - Replace the standard tray shift motor. - Replace the finisher controller PCB. |
| Error code: | E540-8001 |
| Description: | Tray up/down error - When the tray fails to return to the home position even when the 1st tray shift motor has been driven for 20 sec. - When the tray fails to move to another area even when the 1st tray shift motor has been driven for 4 sec. |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8002 |
| Description: | Tray up/down error When a danger area is reached before the sheet level is detected by the 1st tray sheet level detection sensor during the sheet level detection operation - When a discontinuous area was detected during the tray operation |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8003 |
| Description: | Tray up/down error When the input of the clock signal could not be detected within 0.2 sec. during the operation of the 1st tray shift motor |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8004 |
| Description: | Tray up/down error When the input of the clock signal could not be detected within 0.2 sec. during the operation of the 1st tray shift motor |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8005 |
| Description: | Tray up/down error When the lock detection signal was set to OFF 150 ms after the lock detection signal was set to ON |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8006 |
| Description: | Tray up/down error When the lock detection signal could not be set to ON within 1 sec. after the start of the 1st tray shift motor drive |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8007 |
| Description: | Tray up/down error When the lock detection signal fails to go OFF when the 1st tray shift motor is stopped |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E542-0001 |
| Description: | - Optional tray motor or finisher controller PCB failure - Optional tray HP sensor failure - Optional tray clock sensor failure - Optional tray shift motor load failure The optional tray was operated, but the paper surface was not detected. |
| Remedy: | - Check the connector of the optional tray HP sensor. - Check the connector of the optional tray clock sensor. - Check the connector of the optional tray shift motor. - Replace the optional tray HP sensor. - Replace the optional tray clock sensor. - Replace the optional tray shift motor. - Replace the finisher controller PCB. |
| Error code: | E542-0002 |
| Description: | - Optional tray motor or finisher controller PCB failure - Optional tray HP sensor failure - Optional tray clock sensor failure - Optional tray shift motor load failure Cannot move (to the pickup position) within the specified time. |
| Remedy: | - Check the connector of the optional tray HP sensor. - Check the connector of the optional tray clock sensor. - Check the connector of the optional tray shift motor. - Replace the optional tray HP sensor. - Replace the optional tray clock sensor. - Replace the optional tray shift motor. - Replace the finisher controller PCB. |
| Error code: | E542-8001 |
| Description: | Tray shift error When the tray fails to return to the home position even when the 2nd tray shift motor has been driven for 20 sec. - When the tray fails to move to another area even when the 2nd tray shift motor has been driven for 4 sec. |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8002 |
| Description: | Tray shift error - When the upper limit area is reached before the sheet level is detected by the 2nd tray sheet level detection sensor 1 during a sheet level detection operation - When a discontinuous area was detected during the tray operation - When the fact that the area ahead of the 2nd tray sheet level detection sensor 2 has been reached is detected before the sheet level is detected by the 2nd tray sheet level detection sensor 2 during an escape operation |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8004 |
| Description: | Tray shift error When the input of the clock signal could not be detected within 0.2 sec. while the 2nd tray shift motor was running |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8005 |
| Description: | Tray shift error When the lock detection signal was set to OFF 150 ms after the lock detection signal was set to ON |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8006 |
| Description: | Tray shift error When the lock detection signal could not be set to ON within 1 sec. after the 2nd tray shift motor started driving |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8007 |
| Description: | Tray shift error When the lock detection signal fails to go OFF when the 2nd tray shift motor is stopped |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E551-0001 |
| Description: | A. Error in power supply fan (Document Insertion Unit) B. Error in power supply fan (FAN101) (Finisher). A. The lock signal ON is detected while the fan operation. B. The lock signal is detected 1.2 seconds or more while the fan operation. |
| Remedy: | A: A-1. Power supply fan is faulty. A-2. Connector of the power supply fan is disconnected B: B-1. The connector of the power supply fan (FAN101) is disconnected. B-2. The wiring of the power supply fan is faulty. B-3. The power supply fan is faulty. B-4. The finisher controller PCB is faulty. |
| Error code: | E551-0002 |
| Description: | A. Error in power supply fan (Paper Folding Unit) B. Error in power supply fan (FAN101) (Finisher). The lock status is released when the fan stops. |
| Remedy: | A: A-1. Connector of the power supply fan is disconnected. A-2. Power supply fan is faulty. B: B-1. The connector of the power supply fan (FAN101) is disconnected. B-2. The wiring of the power supply fan is faulty. B-3. The power supply fan is faulty. B-4. The finisher controller PCB is faulty. |
| Error code: | E567-0001 |
| Description: | Shift Roller Release Motor fails to move from HP At initial rotation, when the Motor rotates for specified period of time and cannot move from HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M5) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Shift Roller Release Sensor (S3) Connector is physically removed. 4. Check if the Shift Roller Release Sensor (S3) failure occurs. |
| Error code: | E567-0002 |
| Description: | Shift Roller Release Motor fails to return to HP At initial rotation, when the Motor rotates for specified period of time and cannot return to HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M5) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Shift Roller Release Sensor (S3) Connector is physically removed. 4. Check if the Shift Roller Release Sensor (S3) failure occurs. |
| Error code: | E56F-0001 |
| Description: | Entrance Roller Release/Stopper HP Motor fails to move from HP At initial rotation, when the Motor rotates for specified period of time and cannot move from HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M6) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Entrance Roller Release/Stopper HP Sensor (S5) Connector is physically removed. 4. Check if the Entrance Roller Release/Stopper HP Sensor (S5) failure occurs. |
| Error code: | E56F-0002 |
| Description: | Entrance Roller Release/Stopper HP Motor fails to return to HP At initial rotation, when the Motor rotates for specified period of time and cannot return to HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M6) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Entrance Roller Release/Stopper HP Sensor (S5) Connector is physically removed. 4. Check if the Entrance Roller Release/Stopper HP Sensor (S5) failure occurs. |
| Error code: | E571-0001 |
| Description: | Gripper Open/Close Motor fails to move from HP At initial rotation, when the Motor rotates for specified period of time and cannot move from HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M7) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Gripper Arm HP Sensor (S13) Connector is physically removed. 4. Check if the Gripper Unit HP Sensor (S7) failure occurs. |
| Error code: | E571-0002 |
| Description: | Gripper Open/Close Motor fails to return to HP At initial rotation, when the Motor rotates for specified period of time and cannot return to HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M7) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Gripper Arm HP Sensor (S13) Connector is physically removed. 4. Check if the Gripper Unit HP Sensor (S7) failure occurs. |
| Error code: | E575-0001 |
| Description: | - Stack delivery motor or finisher controller PCB failure - Stack delivery HP sensor failure - The stack delivery motor was driven for 2000 ms in the stack delivery direction (HP sensor approach direction), but the stack delivery HP sensor did not turn on. |
| Remedy: | - Check the connector of the stack delivery HP sensor. - Check the connector of the stack delivery motor. - Check the connector of the stack delivery HP sensor. - Replace the stack delivery motor. - Replace the finisher controller PCB. |
| Error code: | E575-0002 |
| Description: | - Stack delivery motor or finisher controller PCB failure - Stack delivery HP sensor failure - The stack delivery motor was driven for 2000 ms in the HP sensor escape direction, but the stack delivery HP sensor did not turn off. |
| Remedy: | - Check the connector of the stack delivery HP sensor. - Check the connector of the stack delivery motor. - Check the connector of the stack delivery HP sensor. - Replace the stack delivery motor. - Replace the finisher controller PCB. |
| Error code: | E584-0002 |
| Description: | - Shutter drive motor or finisher controller PCB failure - Shutter open detection sensor failure - Shutter clutch failure - The shutter open sensor did not turn off when 1000 ms have lapsed since the shutter unit had performed close operation, resulting in incomplete close operation. |
| Causes: | The feed motor (M1) is faulty. The shutter open sensor (PI5) is faulty. |
| Remedy: | - Check the connector of the shutter open sensor. - Check the connector of the shutter clutch. - Check the connector of the shutter motor. - Replace the shutter open sensor. - Replace the shutter clutch. - Replace the shutter drive motor. - Replace the finisher controller PCB. |
| Error code: | E584-8001 |
| Description: | Tray unit trouble When the shutter fails to leave the shutter home position even when the binding motor has been driven for 3 sec. |
| Remedy: | - Check the shutter home position sensor connectors. - Replace the shutter home position sensor. - Replace the shutter open/close clutch (CL101). - Replace the binding bottom roller clutch (CL102). - Replace the binding motor (M102). |
| Error code: | E590-8001 |
| Description: | When the puncher cannot detect the punch home position sensor even when the punch motor is driven for 200 ms |
| Remedy: | - Check the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch motor (M61). |
| Error code: | E590-8002 |
| Description: | When the puncher cannot detect the punch home position sensor after motor drive has stopped during the initial operation of the punch motor |
| Remedy: | - Check the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch motor (M61). |
| Error code: | E591-8001 |
| Description: | When the light sensing voltage is less than 3.0 V even though the lightemitting duty ratio of the waste full detection sensor has been set to more than 66% |
| Remedy: | - Check the waste full detection sensor (LED6, PTR6) connectors. - Replace the waste full detection sensors (LED6, PTR6). |
| Error code: | E591-8002 |
| Description: | When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of the waste full detection sensor has been set to 0% |
| Remedy: | - Check the waste full detection sensor (LED6, PTR6) connectors. - Replace the waste full detection sensors (LED6, PTR6). |
| Error code: | E592-8001 |
| Description: | Sheet trailing edge, side registration sensor error When the light sensing voltage is less than 2.5 V even though the lightemitting duty ratio of the sheet trailing edge sensor has been set to more than 66% |
| Remedy: | - Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4). |
| Error code: | E592-8002 |
| Description: | Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of the sheet trailing edge sensor has been set to 0% |
| Remedy: | - Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4). |
| Error code: | E592 8003 |
| Description: | Horizontal registration sensor 1 error The voltage of the light received is 2.5 V or less even when the light emitting duty of the horizontal registration sensor 1 (LED1,PTR1) has been increased to 66% or more |
| Remedy: | 1. The wiring between the LED PCB/photosensor PCB and punch controller PCB is faulty. 2. The LED PCB and photosensor PCB is faulty. 3. The punch controller PCB is faulty. 4. The finisher controller PCB is faulty. |
| Error code: | E592-8004 |
| Description: | Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of side registration sensor 1 (LED1, PTR1) has been set to 0% |
| Remedy: | - Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4). |
| Error code: | E592-8005 |
| Description: | Sheet trailing edge, side registration sensor error When the light sensing voltage is less than 2.5 V even though the lightemitting duty ratio of side registration sensor 2 (LED2, PTR2) has been set to more than 66% |
| Remedy: | - Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4). |
| Error code: | E592-8006 |
| Description: | Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of side registration sensor 2 (LED2, PTR2) has been set to 0% |
| Remedy: | - Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4). |
| Error code: | E592-8007 |
| Description: | Sheet trailing edge, side registration sensor error When the light sensing voltage is less than 2.5 V even though the lightemitting duty ratio of side registration sensor 3 (LED3, PTR3) has been set to more than 66% |
| Remedy: | - Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4). |
| Error code: | E592-8008 |
| Description: | Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of side registration sensor 3 (LED3, PTR3) has been set to 0% |
| Remedy: | - Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4). |
| Error code: | E592-8009 |
| Description: | Sheet trailing edge, side registration sensor error When the light sensing voltage is less than 2.5 V even though the lightemitting duty ratio of side registration sensor 4 (LED4, PTR4) has been set to more than 66% |
| Remedy: | - Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4). |
| Error code: | E592-800A |
| Description: | Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of side registration sensor 4 (LED4, PTR4) has been set to 0% |
| Remedy: | - Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4). |
| Error code: | E593-8001 |
| Description: | Side registration initializing error When the side registration fails to leave the side registration home position sensor position even when the punch slide unit is moved 9 mm during the initial operation of the side registration motor |
| Remedy: | - Check the side registration home position sensor (P161) connectors. - Replace the side registration home position sensor (P161). - Replace the side registration motor (M62). |
| Error code: | E593-8002 |
| Description: | Side registration initializing error When the side registration fails to return to the side registration home position sensor position even when the punch slide unit is moved 37 mm during the initial operation of the side registration motor |
| Remedy: | - Check the side registration home position sensor (P161) connectors. - Replace the side registration home position sensor (P161). - Replace the side registration motor (M62). |
| Error code: | E5F0-8001 |
| Description: | Saddle sheet positioning error When the sheet positioning plate home position sensor fails to turn ON even when the sheet positioning plate motor is driven by 1500 pulses |
| Remedy: | - Check the sheet positioning plate home position sensor (P17) connectors. - Replace the sheet positioning plate home position sensor (P17). - Replace the sheet positioning plate motor (M4). |
| Error code: | E5F0-8002 |
| Description: | Saddle sheet positioning error When the sheet positioning plate home position sensor fails to turn OFF even when the sheet positioning plate motor is driven by 300 pulses |
| Remedy: | - Check the sheet positioning plate home position sensor (P17) connectors. - Replace the sheet positioning plate home position sensor (P17). - Replace the sheet positioning plate motor (M4). |
| Error code: | E5F1-8001 |
| Description: | Saddle sheet creasing error When the number of detection pulses of the sheet creasing motor clock sensor has dropped below the prescribed number |
| Remedy: | - Check the sheet creasing motor clock sensor (P14) and sheet creasing home position sensor (P121) connectors. - Replace the sheet creasing motor clock sensor (P14) and sheet creasing home position sensor (P121). - Replace the sheet creasing motor (M2). |
| Error code: | E5F1-8002 |
| Description: | Saddle sheet creasing error When the sheet creasing home position sensor status fails to change even when the sheet creasing motor is driven for 3 sec. |
| Remedy: | When the sheet creasing home position sensor status fails to change even when the sheet creasing motor is driven for 3 sec. |
| Error code: | E5F2-8001 |
| Description: | Saddle guide error The guide HP sensor fails to be ON after the guide motor is driven for 0.455 sec. |
| Remedy: | Replace the guide motor (M3S), Replace the guide HP sensor (PI13S) |
| Error code: | E5F2-8002 |
| Description: | Saddle guide error The HP sensor fails to be OFF after the guide motor is driven for 1 sec. |
| Remedy: | Replace the guide motor (M3S), Replace the guide HP sensor (PI13S) |
| Error code: | E5F3-8001 |
| Description: | Saddle alignment error When the alignment plate home position sensor fails to turn ON even when the alignment motor is driven for 0.5 sec. (or driven for 1.67 sec. during the initial operation) |
| Remedy: | - Check the alignment plate home position sensor (P15S) connectors. - Replace the alignment plate home position sensor (P15S). - Replace the alignment motor (M5S). |
| Error code: | E5F3-8002 |
| Description: | Saddle alignment error When the alignment plate home position sensor fails to turn OFF even when the alignment motor is driven for 1 sec. |
| Remedy: | - Check the alignment plate home position sensor (P15S) connectors. - Replace the alignment plate home position sensor (P15S). - Replace the alignment motor (M5S). |
| Error code: | E5F4-8001 |
| Description: | Saddle rear stapler error When the stitch operation home position sensor fails to turn OFF even when the stitch motor (rear) has been run in the forward direction for at least 0.5 sec. |
| Remedy: | - Check the stitch operation home position sensor (rear, MS5S) connectors. - Replace the stitch operation home position sensor (rear, MS5S). - Replace the stitch motor (rear, M6S). |
| Error code: | E5F4-8002 |
| Description: | Saddle rear stapler error When the stitch operation home position sensor fails to turn ON even when the stitch motor (rear) has been run in the reverse direction for at least 0.5 sec. |
| Remedy: | - Check the stitch operation home position sensor (rear, MS5S) connectors. - Replace the stitch operation home position sensor (rear, MS5S). - Replace the stitch motor (rear, M6S). |
| Error code: | E5F5-8001 |
| Description: | Saddle front stapler error When the stitch operation home position sensor fails to turn OFF even when the stitch motor (front) has been run in the forward direction for at least 0.5 sec. |
| Remedy: | - Check the stitch operation home position sensor (front, MS7S) connectors. - Replace the stitch operation home position sensor (front, MS7S). - Replace the stitch motor (front, M7S). |
| Error code: | E5F5-8002 |
| Description: | Saddle front stapler error When the stitch operation home position sensor fails to turn ON even when the stitch motor (front) has been run in the reverse direction for at least 0.5 sec. |
| Remedy: | - Check the stitch operation home position sensor (front, MS7S) connectors. - Replace the stitch operation home position sensor (front, MS7S). - Replace the stitch motor (front, M7S). |
| Error code: | E5F6-8001 |
| Description: | Saddle sheet push plate stapler error When the sheet push plate home position sensor fails to turn ON even when the sheet push plate motor has been run for at least 0.3 sec. |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E5F6-8002 |
| Description: | Saddle sheet push plate stapler error When the sheet push plate home position sensor fails to turn OFF even when the sheet push plate motor has been run for at least 80 ms |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E5F6-8003 |
| Description: | Saddle sheet push plate stapler error When the sheet push plate edge position sensor fails to turn OFF even when the sheet push plate motor has been run for at least 80 ms |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E5F6-8004 |
| Description: | Saddle sheet push plate stapler error When the number of pulses detected by the sheet push plate motor clock sensor has dropped below the prescribed number |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E5F6-8005 |
| Description: | Saddle sheet push plate stapler error When the sheet push plate edge position sensor fails to turn ON even when the sheet push plate motor has been run for at least 0.3 sec. |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E602 |
| Description: | Yellow TCR Sensor adjustment failure - TCR Sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Photoconductor Unit /C • Photoconductor Unit /M • Photoconductor Unit /Y • Toner Supply Motor Y/M (M6) • Toner Supply Motor C/K (M7) • Mechanical Control Board (PWB-M) • Controller Board (PWB-P) |
| Remedy: | 1 Clean the TCR Sensor window on the underside of the Photoconductor Unit if dirty - - 2 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23 3 Reinstall Photoconductor Unit - - 4 Change Photoconductor Unit - - 5 Change PWB-M - - 6 Change PWB-P |
| Error code: | E604-0000 |
| Description: | Memory error |
| Causes: | Lack of memory capacity |
| Remedy: | Check the memory capacity inserted to each slot. |
| Error code: | E609-0008 |
| Description: | Hard disk trouble When the HDD fails to reach the prescribed temperature within the prescribed period of time when it is started up |
| Remedy: | Replace with an HDD which is guaranteed to operate at low temperatures. |
| Error code: | E609-0009 |
| Description: | Hard disk trouble When the HDD fails to reach the prescribed temperature when its operation is restored from the sleep mode |
| Remedy: | Replace with an HDD which is guaranteed to operate at low temperatures. |
| Error code: | E610 |
| Description: | 1st Image Transfer ATVC (color) failure - An abnormal average value is detected while performing the first image transfer ATVC of color. |
| Causes: | • Transfer Belt Unit • Transfer Roller • High Voltage Unit |
| Remedy: | 1 Check if the Transfer Roller and Transfer Belt are dirty and correct as necessary. - - 2 Change High Voltage Unit - - 3 Change Transfer Belt Unit |
| Error code: | E611-0000 |
| Description: | Rebooting repeat error due to SRAM failure, etc. Rebooting error when the SRAM data has been destroyed, the job information saved in the SRAM can no longer be read or when rebooting is otherwise repeated when the power is shut off and restored |
| Remedy: | - Clear the SRAM. - Clear the power shutdown guaranteed jobs. |
| Error code: | E615-0001 |
| Description: | Self test error of encryption module A self test of the Ipsec Board was conducted, and an error was detected. The encryption module is broken. |
| Remedy: | Upgrade the system after HDD format. When this error occurs, normal network communication cannot be guaranteed. |
| Error code: | E674 |
| Description: | Modem error. |
| Remedy: | - Turn the power OFF and then back ON. - Replace the SCNT board. |
| Error code: | E677-0001 |
| Description: | DPRAM size error In communication for initialization, the DPRAM size returned by the PDL board to the host machine has an error. (The host machine is aware of the DPRAM size in advance; the DPRAM is a dual-port RAM used for communication between the host machine and the PDL board, and is mounted on the PDL board.) |
| Causes: | The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty. |
| Remedy: | 1. Connector Is the printer board (accessory) connected correctly? NO: Correct the connection. 2. Printer board, Main controller PCB Try replacing the printer board. Is the problem corrected? YES: End. NO: Replace the main controller PCB. |
| Error code: | E677-0003 |
| Description: | There is an external controller error. An error has been detected by a check on the configuration when the external controller is being started up. |
| Remedy: | Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to start up, re-install the system software of the external contro |
| Error code: | E677-0004 |
| Description: | PDL board disconnection After the connection of the PDL board is recognized at power-on, the PDL board is disconnected. During power-up, monitoring is executed at intervals of 2 min; however, if the CPU is not on (sleep state or the like), no error will be identified even if the PDL board is discontented. If the PDL board is disconnected in sleep state, the absence of the PDL board will be recognized at the start of the CPU. |
| Causes: | The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty. |
| Remedy: | - Check connection of the connector for cooling CPU - Replace CPU cooling fan |
| Error code: | E677-0010 |
| Description: | There is an external controller error. A controller for a non-Canon machine is connected. |
| Remedy: | Turn off the main power, and check the controller is an appropriate type, and check the cable; then turn on the main power. If the machine fails to reset, re-install the system software of the external controller. |
| Error code: | E677-0080 |
| Description: | There is an external controller error. There is an error in the communication with the printer after the external controller has started up normally. |
| Causes: | The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty. |
| Remedy: | Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to start up, re-install the system software of the external controller. |
| Error code: | E710-0001 |
| Description: | IPC initializing error When the ready status fails to be established within 3 sec. after the IPC chip started up |
| Causes: | The DC controller PCB is faulty. The reader controller PCB is faulty. The machine controller PCB is faulty. |
| Remedy: | Check the cable connections. |
| Error code: | E711-0001 |
| Description: | IPC communication error When error occurrence was set 4 or more times in the error register of the IPC chip within 1.5 sec. |
| Causes: | The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty. |
| Remedy: | Check the cable connections. Replace the ADF controller PCB. Replace the reader controller PCB. |
| Error code: | E711-0002 |
| Description: | There is an IPC communication error. An error has been detected 4 times or more within 1.5 sec after the communication has been interrupted between the finisher and the printer, and the machine does not reset. |
| Causes: | The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty. |
| Remedy: | Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to reset, check the connector between the finisher and the copier for poor contact; as necessary, replace the finisher controller/DC controller. |
| Error code: | E713-0000 |
| Description: | Communication error between the finisher and the printer Communication between the finisher and the copier stops. |
| Causes: | The connector has poor connection. The option power supply PCB is faulty. The finisher controller PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Check on connection of the cable, Replace the finisher controller PCB, Replace the DC controller PCB |
| Error code: | E713-0001 |
| Description: | There is a finisher communication error. There is an error in the IC used for communication by the sorter. |
| Remedy: | Turn off the main power switch, and check the wiring of the DC controller PCB and the finisher controller PCB, and check the 24V system fuse: then, turn on the main power switch. If the machine does not reset, replace the DC controller PCB/finisher controller PCB. |
| Error code: | E713-0002 |
| Description: | Error in IPC communication When detecting CRC error at transmission. |
| Remedy: | Check the connector connected to the Finisher. |
| Error code: | E713-0004 |
| Description: | Finisher/printer communication error When communication between the finisher and copier was interrupted |
| Remedy: | Check the cable connections. Replace the finisher controller PCB. Replace the DC controller PCB. |
| Error code: | E713-0010 |
| Description: | Error in UFDI communication Neither ACK nor NAK is returned for specified times in a row. |
| Remedy: | Check the connector connected to the Finisher. |
| Error code: | E713-0011 |
| Description: | Error in UFDI communication NAK is returned for specified times in a row. |
| Remedy: | Check the connector connected to the Finisher. |
| Error code: | E713-0020 |
| Description: | UFDI communication error BCC of the reception data is invalid for specified number of times in a row. |
| Remedy: | Check the connection of the Connector with Finisher. |
| Error code: | E713-0021 |
| Description: | Error in UFDI communication Timeout before the completion of reception for specified times in a row. |
| Remedy: | Check the connector connected to the Finisher. |
| Error code: | E713-0022 |
| Description: | Error in UFDI communication Undefined error for specified times in a row at reception. |
| Remedy: | Check the connector connected to the Finisher. |
| Error code: | E716-0000 |
| Description: | Erroneous communication with optional cassette Disconnection of the optional cassette was detected after power-on, detection of normal connection to the optional cassette, and start of communication. |
| Causes: | The connector has poor connection. The main power supply PCB is faulty. The pedestal controller PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | - Check the connectors of the optional cassette PCB and DC controller PCB. - Replace the optional cassette PCB for normal connection. - Replace the DC controller PCB. |
| Error code: | E717-0001 |
| Description: | Error in communication with NE controller When the NE controller which was connected before the power was turned OFF could not be recognized when the power was turned back ON |
| Causes: | The wiring is faulty (short circuit, open circuit). The DA unit PCB is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR. |
| Remedy: | Check the cable connections. |
| Error code: | E717-0002 |
| Description: | Error in communication with NE controller When the IPC has a broken or disconnected wire or when an error has occurred where IPC communication cannot be recovered |
| Remedy: | In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR. |
| Error code: | E719-0001 |
| Description: | Error in communication with coin vendor/card reader When the coin vendor which was connected before the power was turned OFF could not be recognized when the power was turned back ON |
| Causes: | The wiring is faulty (short circuit, open circuit). The Card Reader-C1 is faulty. The coin vendor is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR. |
| Remedy: | Check the cable connections. |
| Error code: | E719-0002 |
| Description: | Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.) |
| Causes: | Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.) |
| Remedy: | - Check the connection between the image processor PCB and serial PCB. - Check the connectors of the serial PCB and coin vendor for normal connection. - Replace the serial PCB. - Check the coin vendor. - Replace the image processor PCB. |
| Error code: | E719-0011 |
| Description: | Error in communication with coin vendor/card reader When the card reader which was connected before the power was turned OFF could not be recognized when the power was turned back ON |
| Remedy: | In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E719-0012 |
| Description: | Error in communication with coin vendor/card reader When a wire in the IPC cable connected with the card reader is broken or disconnected or when an error has occurred where IPC communication cannot be recovered |
| Remedy: | In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E719-0031 |
| Description: | There is a coin vendor error. Error in communication at card reader (serial) startup Communication with the card reader cannot be started at startup. |
| Remedy: | 1. Check the connection of the cable for the card reader (connector disconnected, cable cut); thereafter, reset the condition in service mode: COPIER > FUNCTION > CLEAR > ERR. 2. Execute the following items in service mode after removing the card reader, and then install the card reader again. - COPIER > FUNCTION > CLEAR > CARD - COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E719-0032 |
| Description: | There is a coin vendor error. Error in communication after card reader (serial) startup Communication with the card reader is available at startup, and then becomes unavailable. |
| Remedy: | Check the connection of the cable for the card reader (connector disconnected, cable cut); thereafter, reset the condition in service mode: COPIER > FUNCTION > CLEAR > ERR. |
| Error code: | E730-1001 |
| Description: | There is a PDL software error. An initialization error has occurred. |
| Remedy: | - Execute PDL resetting. - Turn on the power once again. |
| Error code: | E730-100A |
| Description: | Printer service call |
| Error code: | E730-9004 |
| Description: | There is a PDL software error. There is an error in the communication (PAI) with an external controller. |
| Remedy: | - Turn on the power once main. - Check the connection of the open I/F board and the cable. - Replace the board for the external controller open I/F. - Replace the main controller PCB. |
| Error code: | E730-9005 |
| Description: | There is a PDL software error. Fault in the connector of the vide cable to the external controller |
| Remedy: | - Turn on the power once main. - Check the connection of the open I/F board and the cable. - Replace the board for the external controller open I/F. - Replace the main controller PCB. |
| Error code: | E730-A006 |
| Description: | There is a PDL software error. The PDL board does not respond. A subbootable is faulty or absent. |
| Remedy: | - Execute PDL resetting. - Turn on the power once again. - Check the connection of the UFR board. - Re-install the firmware. - Replace the main controller PCB. |
| Error code: | E730-A007 |
| Description: | There is a PDL software error. There is a mismatch between the control software of the machine and the PDL control software in regard to version. |
| Remedy: | - Execute PDL resetting. - Turn on the power once again. - Execute system formatting (all), and reinstall the system. |
| Error code: | E730-B013 |
| Description: | There is a PDL software error. Corruption in the font data |
| Remedy: | - Turn on the power once again. - Re-install the Software. - Execute system formatting (all), and reinstall the system. |
| Error code: | E732-0000 |
| Description: | Scanner communication error. |
| Causes: | Scanner communication error |
| Remedy: | 1. Install the set of the controller firmware. 2.Replace the Main Controller PCB (UN30). |
| Error code: | E732-0001 |
| Description: | Scanner communication error |
| Causes: | Scanner communication error |
| Remedy: | 1. Update the firmware. 2. Replace the Main Controller PCB. |
| Error code: | E732-0010 |
| Description: | There is an error in the communication with the scanner Fault in detection of DDI-S Vsync signal |
| Remedy: | 1. Check the connector used to connect the scanner. 2. Check the power supply of the scanner (to see if initialization takes place at startup). 3. Replace the reader controller, scanner board, or main board as necessary. |
| Error code: | E732-0021 |
| Description: | Error in scanner communication Error in DDI-S communication |
| Remedy: | 1. Check the connector connecting to the Scanner. 2. Check the power of the Scanner ->whether to perform initialization at start-up? 3. Replace the Rcon, the Scanner Board or the Main controller PCB 2. |
| Error code: | E732-8888 |
| Description: | Reader communication error When the different scanner model is detected. |
| Remedy: | Check the scanner model and the scan type at: COPIER > OPTION > BODY > SCAN TYPE, then make the scan type setting as below. 0 for CIS model reader 1 for CCD model reader |
| Error code: | E732-9999 |
| Description: | There is an error in reader communication. Although a printer model, the machine is identified as a reader unit at start-up. (A copier model is started up as a printer model when the RAM is initialized.) |
| Remedy: | Turn off and then on the main power. |
| Error code: | E733-0000 |
| Description: | Erroneous communication between controller and printer Cannot communicate with the printer at startup. |
| Causes: | Printer communication error (communication error at initial communication and negotiation packet error) |
| Remedy: | - Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB. |
| Error code: | E733-0001 |
| Description: | Printer communication error (Invalid communication after communication is established, Parity error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E733-0002 |
| Description: | Printer communication error. An error occurred to detect printer vertical synchronous signal. |
| Remedy: | 1. Check the connection to the printer. ?¨ Connect the connector/replace the harness. 2. Check the power of the printer (check if the initialization operation is executed at startup). 3. Replace the DC Controller PCB/Main Controller PCB. |
| Error code: | E733-0010 |
| Description: | There is an error in the communication with the printer Fault in detection of DDI-P Vsync signal |
| Remedy: | 1. Check the connection with the printer. 2. Check the power supply of the printer (to see if initialization takes place at startup). 3. Replace the DC controller or the main board. |
| Error code: | E740-0002 |
| Description: | Error detection on either Network Board or Mac address |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of the network cable. (2) Replace the Main Controller Board. |
| Error code: | E743-0000 |
| Description: | Error in main controller communication An error in reading of/writing to the Flash ROM in the Main Controller occurred. |
| Causes: | Software sequence error |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. |
| Error code: | E744 |
| Description: | Stop jam at the original exit/reverse sensor |
| Causes: | Original exit/reverse sensor RADF board Perform the 05-3210 Roller Intermediate transport roller |
| Remedy: | 1. Clean the exit/reverse intermediate roller if it is stained. 2. Is the original exit/reverse sensor working? (Perform input check: 03: [FAX]/ON/[5]/[B]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original exit/reverse sensor or the harnesses are open-circuited. Correct if this is the case. 4. Replace the original exit/reverse sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the exit/reverse intermediate roller, if it is worn out. |
| Error code: | E746 |
| Description: | Original exit/reverse sensor paper remaining jam |
| Causes: | Original exit reverse sensor Registration sensor Original width detection sensor-1 Original width detection sensor-2 Original width detection sensor-3 Intermediate transport sensor Reading end sensor Exit sensor RADF board Perform the 05-3210 Roller |
| Remedy: | 1. Check if there is any paper on each sensor. Remove it if there is. 2. Is each sensor working? (Perform input check: 03) [E746]: [FAX]/ON/[5]/[B], [E762]: [FAX]/ON/[7]/[H], [E770]: [FAX]/ON/[8]/[F], [E771]: [FAX]/ON/[8]/[G], [E772]: [FAX]/ON/[8]/[H], [E773]: [FAX]/ON/[7]/[F], [E774]: [FAX]/ON/[7]/[G], [E775]: [FAX]/ON/[5]/[D], [E777]: [FAX]/ON/[7]/[E] 3. Check if the connector CN74 or CN75 on the RADF board is disconnected from each sensor or the harnesses are open-circuited. Correct if this is the case. 4. Replace each sensor. * If the original reading start sensor is replaced, perform automatic adjustment (05-356) for it. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). |
| Error code: | E748 |
| Description: | Internal cooling fan motor error. When the lock signal is detected continuously for the predetermined time during fan rotation. |
| Causes: | • Fuser Fan Motor (M7) • PH Fan Motor (M8) • Suction Fan Motor (M13) • Ozone Fan Motor (M9) • PS Fan Motor (M6) • PU Fan Motor (M12) |
| Remedy: | 1 Check the motor connector connection status, and correct if it is improper. 2 Check the load status of the fan section, and correct if it is improper. 3 Check the operation of M12. p115 PWB-A CNF3-A-1(REM) 7-C 4 Replace the PWB-A. |
| Error code: | E753-0001 |
| Description: | Error in Finisher Boot software. The Boot software has not been written in ROM of the finisher controller. |
| Remedy: | 1. The finisher controller PCB is faulty. 2. The host machine controller PCB is faulty. |
| Error code: | E760-0001 |
| Description: | Main Controller PCB error |
| Causes: | An error occurred with the firmware of the Main Controller. |
| Remedy: | 1. Update the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E800-0000 |
| Description: | There is an error in the auto power-off circuit. An open circuit is detected in the auto power-off circuit for 3 sec or more. |
| Remedy: | - Turn on the power once again. - Check if the connector (J505) of theDC controller PCB is mounted properly. - Check if the connector (J1719) of the relay PCB is mounted properly. - Replace the relay PCB. - Replace the DC controller PCB. |
| Error code: | E804-0000 |
| Description: | Power supply fan failure |
| Error code: | E804-0001 |
| Description: | Controller fan error Stop of power supply cooling fan 2 was detected |
| Remedy: | Check the connection of power supply cooling fan 2, replace it |
| Error code: | E805-0000 |
| Description: | Fan failure The fan is faulty. |
| Causes: | Fixing fan error Cause The fixing fan is faulty. The engine controller PCB is faulty. |
| Remedy: | - Check the fan connector. - Replace the fan. - Replace the DC controller PCB. |
| Error code: | E805-0001 |
| Description: | Error in duplex cooling fan |
| Causes: | Fan 1 failure |
| Error code: | E805-0002 |
| Description: | Fan Motor 2 error |
| Causes: | The Sub Fan fails to rotate at the specified rotation speed. |
| Remedy: | 1. Check the connection of the Sub Fan. 2. Replace the Sub Fan. |
| Error code: | E805-0003 |
| Description: | Fan failure |
| Causes: | Controller fan failure detected The controller fan does not rotate because some kind of failure occurred in it. |
| Remedy: | Replace the controller fan. |
| Error code: | E806-0000 |
| Description: | Fan Motor cannot rotate at specified revolution speed. |
| Causes: | Fixing / fixing power supply cooling fan does not rotate in the specified rotation speed. Cause: Problem in fixing / fixing power supply cooling fan / DC controller PCB |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Main Fan Unit. (2) Replace the DC Controller Board. |
| Error code: | E806-0001 |
| Description: | Delivery fan error |
| Error code: | E806-0002 |
| Description: | Error in fan of main body The drop of connector of delivery adhesive fan / the disconnection was detected |
| Remedy: | Check the connection of delivery adhesive fan, replace it |
| Error code: | E806-0003 |
| Description: | Error in fan of main body Error in secondary transfer exhaust fan was detected |
| Remedy: | Check the connection of secondary transfer exhaust fan, replace it |
| Error code: | E840-0000 |
| Description: | Pressure release mechanism failure |
| Causes: | The target pressure position was not reached even when 3.5 seconds (approximately 1.5 rotation of the cam) elapsed after start of the fixing motor reverse rotation. |
| Remedy: | Check the gears and detection flags related to fixing pressure release mechanism. Replace the fixing pressure release sensor (PS9). Replace the fixing motor. Replace the fixing assembly. |
| Error code: | E840-0001 |
| Description: | Fixing Core/Shield Plate HP error. At the Fixing Core/Shield Plate home position detection operation, move from inside the home position range to outside the range is not completed after the specified period of time has passed. |
| Remedy: | 1. Check the connection of connectors of the Core Shutter Motor (M56) and Core HP Sensor (PS98). 2. Check the harness of the target parts. -> Replace the harness if it is disconnected. 3. Replace the Core Shutter Motor (M56) and Core HP Sensor (PS98). 4. Clean the IH Unit. (Refer to the Service Manual.) 5. Replace the IH Unit. 6. Replace the Fixing Feed Driver PCB (UN5). |
| Error code: | E840-0002 |
| Description: | Fixing Core/Shield Plate HP error. At the Fixing Core/Shield Plate home position detection operation, move from outside the home position range to inside the range is not completed after the specified period of time has passed. |
| Remedy: | 1. Check the connection of connectors of the Core Shutter Motor (M56) and Core HP Sensor (PS98). 2. Check the harness of the target parts. -> Replace the harness if it is disconnected. 3. Replace the Core Shutter Motor (M56) and Core HP Sensor (PS98). 4. Check the Fixing Film Unit. -> Replace the unit if it is damaged. 5. Clean the IH Unit. (Refer to the Service Manual.) 6. Replace the IH Unit. 7. Replace the Fixing Feed Driver PCB (UN5). |
| Error code: | E840-0003 |
| Description: | Failure of Fixing Film Edge Cooling Fan (Front) (FM2) When the lock signal is detected for 15 sec while the fixing film edge cooling fan (front) stops. * The same status is detected again after the retry operation. |
| Remedy: | 1. Check connection of the Connectors (J2035/J215). 2. Replace the fixing film edge Cooling fan (front) (FM2) 3. Replace the DC controller PCB (UN2). |
| Error code: | E840-0004 |
| Description: | Rotation error of Fixing Film Edge Cooling Fan (Front) (FM2) When the lock signal is detected for 15 sec while the fixing film edge cooling fan (front) operates. * The same status is detected again after the retry operation. |
| Remedy: | 1. Check connection of the Connectors (J2035/J215). 2. Replace the fixing film edge cooling fan (front) (FM2). 3. Replace the DC controller PCB (UN2). |
| Error code: | E880-0001 |
| Description: | Controller fan1 (FM19) Error. When detect a failure of the power supply cooling fan |
| Remedy: | 1. Connector disconnection 2. Controller fan 1 (FM19) failure |
| Error code: | E880-0005 |
| Description: | HDD cooling fan (FM21) error. When detect a failure of the power supply cooling fan |
| Remedy: | 1. Connector disconnection 2. HDD cooling fan (FM21) failure |
