Canon i-SENSYS LBP7750Cdn
Рейтинг
Модули
810 FIXING ASSY
104 INTERNAL COMPONENTS 2
101 FRONT DOOR ASSY
105 INTERNAL COMPONENTS 3
310 CASSETTE PAPER PICK-UP ASSY
100 EXTERNAL PANELS, COVERS, ETC.
107 INTERNAL COMPONENTS 5
103 INTERNAL COMPONENTS 1
300 CASSETTE
106 INTERNAL COMPONENTS 4
311 M.P. PAPER PICK-UP ASSY
102 RIGHT DOOR ASSY
810 FIXING ASSY 2
330 SECONDARY TRANSFER ASSY
320 REGISTRATION ASSY
360 DUPLEXING PAPER FEED ASSY
350 PAPER DELIVERY ASSY
Детали 104 INTERNAL COMPONENTS 2
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-8815-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-8816-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-8824-000 |
| Цена: | 58 300 ₽ |
| Деталь: | FAN CABLE ASSY |
| Парткод: | RM1-5746-000 |
| Деталь: | TRAY, WASTE TONER CATCH |
| Парткод: | RC2-5898-000 |
| Деталь: | HOLDER, CARTRIDGE FAN |
| Парткод: | RC2-5044-000 |
| Деталь: | HOLDER, CARTRIDGE FAN |
| Парткод: | RC2-5932-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | RU6-2436-000 |
| Деталь: | GUIDE, CABLE, LOWER |
| Парткод: | RC2-5971-000 |
| Деталь: | SEAL, CARTRIDGE FAN HOLDER |
| Парткод: | RC2-5993-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | RC2-5970-000 |
| Деталь: | STOPPER, PLATE |
| Парткод: | RC2-5160-000 |
| Деталь: | TAB |
| Парткод: | RC2-5909-000 |
| Деталь: | SHUTTER |
| Парткод: | RC2-5910-000 |
| Деталь: | COVER |
| Парткод: | RC2-5912-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | RC2-5958-000 |
| Деталь: | HOLDER, CRG. LOCK LEVER |
| Парткод: | RC2-5955-000 |
| Деталь: | LEVER, CARTRIDGE LOCK |
| Парткод: | RC2-5954-000 |
| Деталь: | GUIDE, TRANSFER S CABLE, 1 |
| Парткод: | RC2-5966-000 |
| Деталь: | GUIDE, TRANSFER S CABLE, 2 |
| Парткод: | RC2-5967-000 |
| Деталь: | COVER |
| Парткод: | RC2-5962-000 |
| Деталь: | GUIDE, CARTRIDGE ESTRANGEMENT |
| Парткод: | RC2-5969-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2318-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2316-000 |
| Деталь: | TAB |
| Парткод: | RC2-4428-000 |
| Деталь: | LEVER, SHUTTER |
| Парткод: | RC2-4415-000 |
| Деталь: | SHUTTER |
| Парткод: | RC2-4413-000 |
| Деталь: | ARM, SHUTTER, REAR |
| Парткод: | RC2-4407-000 |
| Деталь: | ARM, SHUTTER, FRONT |
| Парткод: | RC2-4406-000 |
| Деталь: | SENSOR UNIT, TMP./HUM. SENSING |
| Парткод: | RK2-2229-000 |
| Деталь: | BASE |
| Парткод: | RL1-2144-000 |
| Деталь: | TONER SENSOR HOLDER ASSY |
| Парткод: | RM1-5700-000 |
| Деталь: | BASE |
| Парткод: | RL1-1923-000 |
| Деталь: | BASE ASSY |
| Парткод: | RM1-4979-000 |
| Деталь: | LOWER CRG. GUIDE ASSY |
| Парткод: | RM1-4984-000 |
| Деталь: | CONNECTING CABLE ASSY |
| Парткод: | RM1-5749-000 |
| Деталь: | SENSOR CABLE ASSY |
| Парткод: | RM1-5740-000 |
| Деталь: | SENSOR CABLE ASSY |
| Парткод: | RM1-5741-000 |
| Деталь: | MOTOR/SENSOR CABLE ASSY |
| Парткод: | RM1-5752-000 |
| Деталь: | LASER/SCANNER ASSY |
| Парткод: | RM1-5676-000 |
| Деталь: | FAN |
| Парткод: | RK2-2418-000 |
| Деталь: | STAND ASSY |
| Парткод: | RM1-5588-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | FM3-8798-000 |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | FM3-9067-000 |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | FM3-9068-000 |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | FM3-9069-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-4541-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-4875-000 |
| Деталь: | PLATE,CST. POSITIONING,FR. RT. |
| Парткод: | RC2-4869-000 |
| Деталь: | PLATE,CST. POSITIONING,RR. RT. |
| Парткод: | RC2-4871-000 |
| Деталь: | GUIDE, DOOR LATCH, RIGHT |
| Парткод: | RC2-4914-000 |
| Деталь: | LINK, DOOR STOPPER |
| Парткод: | RC2-4916-000 |
| Деталь: | GUIDE, OPTION ENTRANCE |
| Парткод: | RC2-4915-000 |
| Деталь: | GUIDE, SENSOR CABLE |
| Парткод: | FC8-9803-000 |
| Деталь: | COVER, INNER, RIGHT LOWER |
| Парткод: | RC2-5019-000 |
| Деталь: | LINK, INTERLOCK |
| Парткод: | RC2-5120-000 |
| Деталь: | MOUNT, INTERLOCK SWITCH |
| Парткод: | RC2-5123-000 |
| Деталь: | ARM, INTERLOCK LINK SWITCH |
| Парткод: | RC2-5121-000 |
| Деталь: | HOLDER, SWITCH |
| Парткод: | RC2-5113-000 |
| Деталь: | LINK, INTERLOCK |
| Парткод: | RC2-5119-000 |
| Деталь: | LINK, INTERLOCK |
| Парткод: | RC2-5118-000 |
| Деталь: | FRAME, INTERLOCK |
| Парткод: | RC2-5117-000 |
| Деталь: | GEAR, 19T |
| Парткод: | RU6-0536-000 |
| Деталь: | SHAFT |
| Парткод: | RC2-5913-000 |
| Деталь: | GUIDE, DUPLEXING REVERSE |
| Парткод: | FC8-9794-000 |
| Деталь: | LEVER, CARTRIDGE LOCK |
| Парткод: | RC2-5954-000 |
| Деталь: | HOLDER, CARTRIDGE LOCK LEVER |
| Парткод: | RC2-5957-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | RC2-5958-000 |
| Деталь: | HOLDER, CARTRIDGE LOCK LEVER |
| Парткод: | RC2-5956-000 |
| Деталь: | GEAR, 26T |
| Парткод: | RU6-0521-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | RC2-4378-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | RU6-2268-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | RC2-4377-000 |
| Деталь: | LINK, INTERLOCK |
| Парткод: | RC2-5122-000 |
| Деталь: | HINGE, RIGHT DOOR, FRONT |
| Парткод: | RC2-4894-000 |
| Деталь: | SUPPORT, RIGHT DOOR, FRONT |
| Парткод: | RL1-1925-000 |
| Деталь: | REAR LOCK ARM ASSY |
| Парткод: | RM1-5533-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | PLATE, GROUNDING RESISTOR |
| Парткод: | RC2-6028-000 |
| Деталь: | 2ND TRANSFER ROLLER ASSY |
| Парткод: | RM1-4990-000 |
| Деталь: | RIGHT CASSETTE RAIL ASSY |
| Парткод: | RM1-5012-000 |
| Деталь: | DENSITY DETECT SENSOR ASSY |
| Парткод: | RM1-4953-000 |
| Деталь: | LOWER PICK-UP GUIDE ASSY |
| Парткод: | RM1-4980-000 |
| Деталь: | INTERMEDIATE TRANS. BELT ASSY |
| Парткод: | FM3-8817-000 |
| Деталь: | CONTROL PANEL CABLE ASSY |
| Парткод: | FM4-1584-000 |
| Деталь: | SWITCH CABLE ASSY |
| Парткод: | RM1-5718-000 |
| Деталь: | FRONT CABLE ASSY |
| Парткод: | FM4-1585-000 |
| Деталь: | FRONT LOCK ARM ASSY |
| Парткод: | RM1-5532-000 |
| Деталь: | SWITCH |
| Парткод: | WC4-5171-000 |
| Деталь: | DOOR SWICH ASSY |
| Парткод: | RM1-5732-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | PAPER PICK-UP ROLLER ASSY |
| Парткод: | RM1-4968-000 |
| Деталь: | PHOTO INTERPRUPER |
| Парткод: | WG8-5696-000 |
| Деталь: | CASSETTE PAPER PICK-UP ASSY |
| Парткод: | RM1-4967-000 |
| Деталь: | COVER, RIGHT FRONT |
| Парткод: | FC8-9779-000 |
| Деталь: | COVER, REAR |
| Парткод: | FC8-9766-000 |
| Деталь: | COVER, LEFT |
| Парткод: | FC8-9763-000 |
| Деталь: | COVER, UPPER |
| Парткод: | FM3-8793-000 |
| Деталь: | COVER, REAR RIGHT |
| Парткод: | FC8-9770-000 |
| Деталь: | COVER, RIGHT LOWER |
| Парткод: | FC8-9776-000 |
| Деталь: | COVER, REAR UPPER |
| Парткод: | FC8-9765-000 |
| Деталь: | E, BASE, PANEL, PLATE |
| Парткод: | FC8-9769-000 |
| Деталь: | TRAY, PAPER DELIVERY |
| Парткод: | FM3-8794-000 |
| Деталь: | TRAY, PAPER DELIVERY |
| Парткод: | FM3-8809-000 |
| Деталь: | TRAY, PAPER DELIVERY |
| Парткод: | FM4-3169-000 |
| Деталь: | OPERATION PANEL ASSY |
| Парткод: | FM3-8812-000 |
| Деталь: | OPERATION PANEL ASSY |
| Парткод: | FM3-8813-000 |
| Деталь: | OPERATION PANEL ASSY |
| Парткод: | FM3-8814-000 |
| Деталь: | OPERATION PANEL ASSY |
| Парткод: | FM3-8822-000 |
| Деталь: | COVER, CONTROL PANEL ASSY, LT |
| Парткод: | FC8-9783-000 |
| Деталь: | COVER, CONTROL PANEL ASSY, RT |
| Парткод: | FC8-9784-000 |
| Деталь: | PLATE, SHIELD |
| Парткод: | FC8-9800-000 |
| Цена: | 1 300 ₽ |
| Деталь: | PLATE, SHIELD R |
| Парткод: | FC8-9819-000 |
| Деталь: | EXTERNAL PANELS, COVERS, ETC. |
| Парткод: | NPN |
| Деталь: | DUPLEXING UNIT CABLE ASSY |
| Парткод: | RM1-5730-000 |
| Деталь: | ARM, SOLENOID |
| Парткод: | RC2-4824-000 |
| Деталь: | PLATE,CST. POSITIONING,RR. LF. |
| Парткод: | RC2-4872-000 |
| Деталь: | STOPPER, SCANNER |
| Парткод: | RC2-5015-000 |
| Деталь: | PICK-UP MOTOR CABLE ASSY |
| Парткод: | RM1-5731-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | RU6-2405-000 |
| Деталь: | LIFTER DRIVE ASSY |
| Парткод: | RM1-4976-000 |
| Деталь: | DRUM MOTOR ASSY |
| Парткод: | RM1-4988-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | RC2-5104-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | RC2-9069-000 |
| Деталь: | MEMORY TAG DETECT ASSY |
| Парткод: | RM1-5712-000 |
| Деталь: | CONNECTOR, DRAWER |
| Парткод: | VS1-7258-007 |
| Цена: | 360 ₽ |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | CST. PAPER PICK-UP DRIVE ASSY |
| Парткод: | RM1-4975-000 |
| Деталь: | GUIDE, ROLLER, REAR |
| Парткод: | RC2-5961-000 |
| Деталь: | LEVER, PRESSURE, REAR |
| Парткод: | RC2-3972-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2234-000 |
| Деталь: | GUIDE, PRE-EXPOSURE CABLE |
| Парткод: | RC2-5959-000 |
| Деталь: | REAR PRE-EXPOSURE PCB ASSY |
| Парткод: | RM1-5705-000 |
| Деталь: | HIGH VOLTAGE HOLDER ASSY |
| Парткод: | RM1-4978-000 |
| Деталь: | SHEET, PRE-EXPOSURE COVER |
| Парткод: | RC2-5968-000 |
| Деталь: | FIXING DRIVE ASSY |
| Парткод: | RM1-4974-000 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | RM1-4954-000 |
| Деталь: | DUPLEXING DRIVE ASSY |
| Парткод: | RM1-4973-000 |
| Деталь: | GUIDE, REAR CABLE, RIGHT |
| Парткод: | RC2-5017-000 |
| Деталь: | PICK-UP MOTOR ASSY |
| Парткод: | RM1-5773-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-2415-000 |
| Деталь: | FIXING MOTOR ASSY |
| Парткод: | RM1-4983-000 |
| Деталь: | INTERNAL COMPONENTS 5 |
| Парткод: | NPN |
| Деталь: | LEFT CABLE ASSY |
| Парткод: | RM1-5742-000 |
| Цена: | 1 800 ₽ |
| Деталь: | PLATE,CST. POSITIONING,FR. LF. |
| Парткод: | RC2-4870-000 |
| Деталь: | COVER, FRONT INNER, LOWER |
| Парткод: | FM3-8827-000 |
| Цена: | 1 600 ₽ |
| Деталь: | GUIDE, CABLE, FRONT |
| Парткод: | RC2-5011-000 |
| Деталь: | COVER, FRONT INNER, UPPER |
| Парткод: | RC2-5006-000 |
| Деталь: | COVER, FRONT INNER, LOWER |
| Парткод: | FM3-8828-000 |
| Цена: | 850 ₽ |
| Деталь: | GUIDE, CABLE, UPPER |
| Парткод: | RC2-5010-000 |
| Деталь: | COVER, LEFT LOWER |
| Парткод: | FC8-9764-000 |
| Деталь: | COVER, FACE-DOWN DUCT |
| Парткод: | RC2-4830-000 |
| Деталь: | DUCT, PAPER DELIVERY |
| Парткод: | RC2-4820-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2567-000 |
| Цена: | 320 ₽ |
| Деталь: | WASTE TONER DETECT ASSY |
| Парткод: | RM1-5696-000 |
| Деталь: | WASTE TONER DUCT ASSY |
| Парткод: | RM1-4977-000 |
| Деталь: | COVER, RIGHT DOOR GEAR, REAR |
| Парткод: | RC2-4924-000 |
| Деталь: | RAIL, GUIDE, FRONT |
| Парткод: | RC2-4783-000 |
| Деталь: | GUIDE, ROLLER, FRONT |
| Парткод: | RC2-5960-000 |
| Цена: | 140 ₽ |
| Деталь: | SPRING, TENSION |
| Парткод: | RU6-2236-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | RU6-2237-000 |
| Деталь: | LEVER, CRG. PRESSURE, FRONT |
| Парткод: | RC2-3983-000 |
| Деталь: | GUIDE, LIGHT |
| Парткод: | RC2-4426-000 |
| Деталь: | SEAL, WASTE TONER BOX |
| Парткод: | RC2-4780-000 |
| Деталь: | FRONT PRE-EXPOSURE PCB ASSY |
| Парткод: | RM1-5704-000 |
| Деталь: | PLATE, GROUNDING RESISTOR |
| Парткод: | RC2-5900-000 |
| Деталь: | LOCK, DOOR |
| Парткод: | RC2-5937-000 |
| Деталь: | COVER, CABLE |
| Парткод: | RC2-5950-000 |
| Деталь: | LEVER, BOX PRESENCE DETECT |
| Парткод: | RC2-5951-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2568-000 |
| Деталь: | CABLE, DEVELOP |
| Парткод: | RM1-7037-000 |
| Деталь: | RAIL, CASSETTE, LEFT |
| Парткод: | RL1-1920-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | RU6-2245-000 |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | RM1-4966-000 |
| Деталь: | CASSETTE |
| Парткод: | FM3-8800-000 |
| Деталь: | FIXING CONNECTING CABLE ASSY |
| Парткод: | RM1-5714-000 |
| Деталь: | LINK, DOOR STOPPER |
| Парткод: | RC2-4916-000 |
| Деталь: | PANEL, GUARD |
| Парткод: | RL1-1948-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RC2-5021-000 |
| Деталь: | HOLDER, 2ND TRNSFR. CONTACT |
| Парткод: | RC2-5020-000 |
| Деталь: | FAN |
| Парткод: | RK2-2416-000 |
| Деталь: | HANDLE, REAR |
| Парткод: | FC8-9767-000 |
| Деталь: | DUCT, DUPLEXING FAN |
| Парткод: | RC2-5047-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | RC2-5148-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | RC2-5930-000 |
| Деталь: | ARM, SWITCH |
| Парткод: | FC8-9817-000 |
| Деталь: | HOLDER, DUPLEXING FAN |
| Парткод: | RC2-5046-000 |
| Деталь: | GUIDE, FLEXIBLE FLAT CABLE |
| Парткод: | RC2-5933-000 |
| Деталь: | SUPPORT, RIGHT DOOR, REAR |
| Парткод: | RL1-1926-000 |
| Деталь: | COUNTER CABLE |
| Парткод: | FM4-1592-000 |
| Деталь: | CABLE, SCANNER FLAT |
| Парткод: | RK2-2506-000 |
| Деталь: | REAR CABLE ASSY |
| Парткод: | RM1-5721-000 |
| Деталь: | SWITCH CONNECTING CABLE ASSY |
| Парткод: | RM1-5719-000 |
| Деталь: | INNER CONNECTING PCB ASSY |
| Парткод: | FM3-8805-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | FM4-1628-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | FM4-1631-000 |
| Деталь: | MAIN CONTROLLER ASSY |
| Парткод: | FM4-1638-000 |
| Деталь: | COVER, CROSSMEMBER, RIGHT REAR |
| Парткод: | RC2-5016-000 |
| Деталь: | HOLDER, LINK |
| Парткод: | RC2-4918-000 |
| Деталь: | PLATE, REINFOR |
| Парткод: | RC2-6027-000 |
| Деталь: | HINGE, RIGHT DOOR, REAR |
| Парткод: | RC2-4895-000 |
| Деталь: | FAN |
| Парткод: | FK2-0993-000 |
| Деталь: | SPACER, LOCK |
| Парткод: | RC2-9074-000 |
| Деталь: | M.P. SENSOR CABLE ASSY |
| Парткод: | RM1-5737-000 |
| Деталь: | POWER SUPPLY GROUNDING UNIT |
| Парткод: | FM4-4178-000 |
| Деталь: | POWER SUPPLY GROUNDING UNIT |
| Парткод: | FM4-5110-000 |
| Деталь: | POWER SUPPLY GROUNDING UNIT |
| Парткод: | FM4-1593-000 |
| Деталь: | LW. H.V.POWER SUPPLY PCB ASSY |
| Парткод: | RM1-5680-000 |
| Деталь: | UP. H.V.POWER SUPPLY PCB ASSY |
| Парткод: | RM1-5681-000 |
| Деталь: | DC CONROLLER PCB ASSY |
| Парткод: | FM4-1580-000 |
| Деталь: | SCREW,TAPPING,TRUSS HEAD,M4X10 |
| Парткод: | XB4-7401-005 |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | ROLLER, MULTI-PURPOSE PICK-UP |
| Парткод: | RL1-2184-000 |
| Деталь: | PAD, MULTI-PURPOSE SEPARATION |
| Парткод: | RL1-1937-000 |
| Деталь: | M.P. PAPER PICK-UP ASSY |
| Парткод: | RM1-4961-000 |
| Деталь: | CAM, STOPPER |
| Парткод: | RC2-6018-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | RU6-2569-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | RC2-4734-000 |
| Деталь: | GEAR, 26T |
| Парткод: | RU6-0509-000 |
| Деталь: | LEVER, STOPPER |
| Парткод: | RC2-9073-000 |
| Деталь: | RIGHT DOOR ASSY |
| Парткод: | FM3-8796-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-8815-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-8816-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-8824-000 |
| Цена: | 58 300 ₽ |
| Деталь: | SECONDARY TRANSFER ASSY |
| Парткод: | RM1-4952-000 |
| Деталь: | REGISTRATION ASSY |
| Парткод: | RM1-4969-000 |
| Деталь: | DUPLEXING PAPER FEED ASSY |
| Парткод: | RM1-4959-000 |
| Деталь: | PAPER DELIVERY ASSY |
| Парткод: | RM1-4970-000 |
Коды ошибок
E000-0000
E001-0000
E001-0001
E001-0004
E003-0000
E003-0001
E003-0004
E004-0000
E012-0002
E012-0003
E012-0004
E012-0005
E012-0006
E012-0007
E012-0008
E012-0009
E014-0000
E014-0001
E015-0000
E015-0001
E015-0002
E020-0000
E066-0000
E06F-0068
E078-0001
E100-0000
E100-0001
E100-0002
E100-0003
E100-0004
E110-0000
E110-0001
E196-0000
E196-0001
E198-0000
E602-0001
E602-0002
E602-0003
E602-0006
E602-0007
E604-0000
E730-100A
E730-C000
E730-C001
E733-0001
E733-0004
E733-0005
E733-0006
E740-0002
E740-0004
E744-0800
E744-0900
E744-1000
E748-4000
E748-4020
E760-0000
E804-0000
E805-0003
E805-0006
E806-0001
E808-0001
E825-0000
E825-0001
E825-0002
E825-0003
E825-0004
E840-0000
Описание
| Error code: | E000-0000 |
| Description: | Startup error The temperature detected by the main or sub thermistor does not rise to the specified value during startup control. |
| Causes: | The detection temperature of the main thermistor did not increase after start of the power distribution to the heater. |
| Remedy: | - Check the fixing film connector. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0000 |
| Description: | Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature 235 deg C) during temperature control |
| Causes: | The main thermistor detected a temperature of higher than 255 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0001 |
| Description: | Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control. |
| Causes: | The sub thermistor detected a temperature of higher than 290 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0004 |
| Description: | Abnormal high temperature in fixing |
| Causes: | The sub thermistor 2 detected a temperature exceeding a specified temperature |
| Remedy: | Replace the fixing assembly. Replace the DC controller PCB. |
| Error code: | E003-0000 |
| Description: | Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0001 |
| Description: | Abnormally low temperature (detected by sub thermistor) After the temperature detected by the sub thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The sub thermistor detected a temperature of lower than 80 degree C for more than 2 seconds when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0004 |
| Description: | Abnormal low temperature in fixing |
| Causes: | The sub thermistor 2 detected a temperature lower than a specified temperature. |
| Remedy: | Replace the fixing assembly. Replace the DC controller PCB. |
| Error code: | E004-0000 |
| Description: | Fixing power supply drive circuit error |
| Causes: | 43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly. |
| Error code: | E012-0002 |
| Description: | ITB motor or drum motor failure |
| Causes: | Yellow drum motor error (Failure in drum motor initial operation) The target speed was not reached within a specified time after startup of the motor |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly. |
| Error code: | E012-0003 |
| Description: | ITB motor or drum motor failure |
| Causes: | Yellow drum motor error (Failure in drum motor rotation) The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly |
| Error code: | E012-0004 |
| Description: | ITB motor or drum motor failure |
| Causes: | Magenta drum motor error (Failure in drum motor initial operation) The target speed was not reached within a specified time after startup of the motor. |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly. |
| Error code: | E012-0005 |
| Description: | ITB motor or drum motor failure |
| Causes: | Magenta drum motor error (Failure in drum motor rotation) The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly. |
| Error code: | E012-0006 |
| Description: | ITB motor or drum motor failure |
| Causes: | Cyan drum motor error (Failure in drum motor initial operation) The target speed was not reached within a specified time after startup of the motor. |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly. |
| Error code: | E012-0007 |
| Description: | ITB motor or drum motor failure |
| Causes: | Cyan drum motor error (Failure in drum motor rotation) The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly. |
| Error code: | E012-0008 |
| Description: | ITB motor or drum motor failure |
| Causes: | Black drum motor error (Failure in drum motor initial operation) The target speed was not reached within a specified time after startup of the motor. |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly. |
| Error code: | E012-0009 |
| Description: | ITB motor or drum motor failure |
| Causes: | Black drum motor error (Failure in drum motor rotation) The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly. |
| Error code: | E014-0000 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor startup error The target speed was not reached within a specified time after startup of the motor. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E014-0001 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E015-0000 |
| Description: | Developing disengagement motor failure |
| Causes: | Developing disengagement motor failure The standard flag was not detected even when driving was performed for 1000ms after rotation of the motor. The standard flag was not detected even when driving was performed for 8000ms at the time of switching from the full-color position to "all disengagement". The standard flag was not detected even when driving was performed for 3000ms at the time of switching from the monochrome position to "all disengagement". |
| Remedy: | Reconnect the connector J518 of the developing disengagement motor, the connector J1005 on the driver PCB, and the connector J91 on the DC controller PCB. Check the condition of the developing disengagement sensor in the sensor monitor mode. If a failure is found, replace the developing disengagement sensor assembly. Execute the developing assembly engagement/disengagement drive test in the actuator drive mode. If the developing assembly does not perform engagement/disengagement, replace the developing disengagement motor. |
| Error code: | E015-0001 |
| Description: | Cassette 1 lift up motor error |
| Causes: | Cassette 1 lift up motor error |
| Remedy: | Reconnect the connector J151 on the DC controller PCB and the relay connector J742. Check the cassette media stack surface sensor in the sensor monitor mode. If a failure is found, replace the lifter drive unit. Replace the lifter drive unit. |
| Error code: | E015-0002 |
| Description: | Cassette 2 lift up motor error |
| Causes: | Cassette 2 lift up motor error |
| Remedy: | Reconnect the connector J2003 on the paper feeder driver PCB and the relay connector J702. Check the paper feeder media stack surface sensor in the sensor monitor mode. If a failure is found, replace the pickup unit. Reconnect the connector J2006 on the paper feeder driver PCB. Replace the lifter drive unit. |
| Error code: | E020-0000 |
| Description: | Density sensor failure warning |
| Error code: | E066-0000 |
| Description: | Environment sensor failure |
| Causes: | Environment sensor failure |
| Remedy: | Replace the environment sensor. |
| Error code: | E06F-0068 |
| Description: | EEPROM access failure |
| Causes: | EEPROM access failure |
| Remedy: | Replace the EEPROM. |
| Error code: | E078-0001 |
| Description: | Primary transfer disengagement mechanism failure |
| Causes: | Primary transfer disengagement mechanism failure At the time of searching the home position: Considering that the coupling of primary transfer engagement/ disengagement drive may not be connected, the solenoid was pulled for maximum 6 times in the condition where the flag was detected once. But the HP sensor did not detect the color print engagement position. * If a flag is not detected even once, it is considered that the ITB unit is absent. At the time of changing the position The position after turning ON/OFF of the solenoid did not match the HP sensor value. |
| Remedy: | Check whether the ITB unit is installed or not. Reconnect the connector J181 on the DC controller PCB. Check the primary transfer roller disengagement switch in the sensor monitor mode. If a failure is found, replace the primary transfer roller disengagement switch assembly. Execute the primary transfer roller engagement/disengagement drive test in the actuator drive mode. If the primary transfer roller does not perform engagement/disengagement, replace the fixing drive unit. |
| Error code: | E100-0000 |
| Description: | BD detection PCB failure The BD detection PCB is faulty. |
| Causes: | Yellow optical assembly failure |
| Remedy: | - Check the connector of the BD detection PCB. - Replace the laser scanner unit. - Replace the DC controller PCB. |
| Error code: | E100-0001 |
| Description: | Error detection on any of scanner motor, laser unit, and BD detection at scanner area. |
| Causes: | Magenta optical assembly failure |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Laser Scanner Unit. (2) Replace the DC Controller Board. |
| Error code: | E100-0002 |
| Description: | Optical assembly error (Laser) |
| Causes: | Cyan optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E100-0003 |
| Description: | Optical assembly error (Laser) |
| Causes: | Black optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E100-0004 |
| Description: | Optical assembly error (Laser) |
| Causes: | Optical assembly error (Laser failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0000 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor initial operation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0001 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor rotation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E196-0000 |
| Description: | Invalid RFU execution requested |
| Causes: | D-con update for the host machine or the optional cassette is not completed. |
| Error code: | E196-0001 |
| Description: | Image processor PCB failure Error on writing and readout ROM of image processor PCB (mainn ROM). |
| Causes: | D-con update for the optional cassette is not completed. |
| Remedy: | - Putting the switch on/off of the power supply. - Replace the image processor PCB. |
| Error code: | E198-0000 |
| Description: | DC controller memory failure |
| Causes: | A checksum failure is found in the block where specific information of the DC controller PCB is saved. A communication error occurred when reading the specific information of the DC controller PCB from the NVRAM at power-on. |
| Remedy: | If the failure cannot be removed by turning the power OFF/ON, replace the DC controller PCB. |
| Error code: | E602-0001 |
| Description: | HDD error |
| Causes: | Lack of the HDD capacity The capacity of the HDD installed is smaller than that of the HDD used in the software. |
| Error code: | E602-0002 |
| Description: | HDD error |
| Causes: | Bootable load failure A Bootable CD was not contained. A Bootable CD was damaged. |
| Remedy: | Burn the Bootable CD again. |
| Error code: | E602-0003 |
| Description: | HDD error |
| Causes: | HDD access error An error occurred caused by the device or hardware when accessing to the HDD during execution of bootrom. (Damage to the sector / Busy device status, etc.) |
| Remedy: | Turn on the power again. |
| Error code: | E602-0006 |
| Description: | HDD error |
| Causes: | SubBootable load failure A SubBootable CD was not contained. A SubBootable CD was damaged. |
| Remedy: | Burn the SubBootable CD again. |
| Error code: | E602-0007 |
| Description: | HDD error |
| Causes: | The contents (ICC-Profile, etc.) could not be detected. (The contents were not contained. The contents were damaged, etc.) |
| Remedy: | Burn the Bootable CD again. |
| Error code: | E604-0000 |
| Description: | Memory error |
| Causes: | Lack of memory capacity |
| Remedy: | Check the memory capacity inserted to each slot. |
| Error code: | E730-100A |
| Description: | Printer service call |
| Error code: | E730-C000 |
| Description: | An error such as memory not acquired at initialization occurred. |
| Remedy: | Turn on the power again. |
| Error code: | E730-C001 |
| Description: | An error occurred when accessing the HDD. |
| Remedy: | Turn on the power again. |
| Error code: | E733-0001 |
| Description: | Printer communication error (Invalid communication after communication is established, Parity error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E733-0004 |
| Description: | Printer communication error (Undefined command error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E733-0005 |
| Description: | Printer communication error (Communication timeout error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E733-0006 |
| Description: | Printer communication error (Unknown communication error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E740-0002 |
| Description: | Error detection on either Network Board or Mac address |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of the network cable. (2) Replace the Main Controller Board. |
| Error code: | E740-0004 |
| Description: | LAN controller chip access error |
| Remedy: | 1.Check the area around the LAN chip. 2.Replace the board. |
| Error code: | E744-0800 |
| Description: | Model code mismatch |
| Remedy: | Replace Soft-ID PCB. |
| Error code: | E744-0900 |
| Description: | Model code mismatch |
| Remedy: | Change to proper bootable |
| Error code: | E744-1000 |
| Description: | Mismatch of the series or model of the firmware sent at the time of downloading |
| Remedy: | Check the supported series or model of the firmware, and burn the correct series or model of firmware. |
| Error code: | E748-4000 |
| Description: | Timeout of G-Chip loop back |
| Remedy: | Replace the main controller PCB. |
| Error code: | E748-4020 |
| Description: | Unknown device detected on the PCI |
| Remedy: | Replace the main controller PCB. |
| Error code: | E760-0000 |
| Description: | CPU exception occurred. |
| Remedy: | Turn on the power again. |
| Error code: | E804-0000 |
| Description: | Power supply fan failure |
| Error code: | E805-0003 |
| Description: | Fan failure |
| Causes: | Controller fan failure detected The controller fan does not rotate because some kind of failure occurred in it. |
| Remedy: | Replace the controller fan. |
| Error code: | E805-0006 |
| Description: | Fan failure |
| Causes: | Power supply fan failure The fan did not rotate even when 12 seconds elapsed after the motor rotation start order was received. |
| Remedy: | Reconnect the connector J21 on the DC controller PCB and the connector J106 on the low-voltage power supply unit. If the voltage between the connectors J21-2 and J25-2 on the DC controller PCB is changed from 0V to approximately 24V immediately after the printer is turned on, replace the power supply fan. |
| Error code: | E806-0001 |
| Description: | Delivery fan error |
| Error code: | E808-0001 |
| Description: | Fixing Assembly_Edge Left Cooling Fan error |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Edge Left Cooling Fan. (2) Replace the DC Controller Board. |
| Error code: | E825-0000 |
| Description: | Drum phase control sensor failure warning |
| Causes: | Yellow drum phase control sensor failure warning A slit was not detected for 4 seconds after slit detection started. An abnormal slit width was detected. |
| Remedy: | Check the YMC drum drive gear. Replace the YMC drum HP sensor (PS13). |
| Error code: | E825-0001 |
| Description: | Drum phase control sensor failure warning |
| Causes: | Magenta drum phase control sensor failure warning A slit was not detected for 4 seconds after slit detection started. An abnormal slit width was detected. |
| Remedy: | Check the YMC drum drive gear. Replace the YMC drum HP sensor (PS13). |
| Error code: | E825-0002 |
| Description: | Drum phase control sensor failure warning |
| Causes: | Cyan drum phase control sensor failure warning A slit was not detected for 4 seconds after slit detection started. An abnormal slit width was detected |
| Remedy: | Check the YMC drum drive gear. Replace the YMC drum HP sensor (PS13). |
| Error code: | E825-0003 |
| Description: | Drum phase control sensor failure warning |
| Causes: | Black drum phase control sensor failure warning A slit was not detected for 4 seconds after slit detection started. An abnormal slit width was detected. |
| Remedy: | Check the Bk drum drive gear. Replace the Bk drum HP sensor (PS12). |
| Error code: | E825-0004 |
| Description: | Drum phase control sensor failure warning |
| Causes: | OHT sensor failure warning |
| Error code: | E840-0000 |
| Description: | Pressure release mechanism failure |
| Causes: | The target pressure position was not reached even when 3.5 seconds (approximately 1.5 rotation of the cam) elapsed after start of the fixing motor reverse rotation. |
| Remedy: | Check the gears and detection flags related to fixing pressure release mechanism. Replace the fixing pressure release sensor (PS9). Replace the fixing motor. Replace the fixing assembly. |
