Konica-Minolta bizhub 367
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
48000
Скорость печати
A4
36
Цветность печати
черно-белая
Общие характеристики |
|
|---|---|
Тип |
лазерный/светодиодный |
Область применения |
малый офис |
Цветность печати |
|
Технология печати |
лазерная |
Макс. формат |
A3 |
Число страниц в месяц |
48 000 |
Размещение |
напольный |
Сканер |
|
Тип устройства |
МФУ |
Копир |
|
Печать фотографий |
|
Телефон |
|
Факс |
|
Принтер |
|
Печать без полей |
|
Пигментные чернила |
|
Прямая печать |
|
Система непрерывной подачи чернил |
|
Макс, ширина отпечатка |
297 |
Время разогрева |
20 |
Двусторонняя печать |
|
Макс, длина отпечатка |
355 |
Макс, разрешение для ч/б печати |
|
| По Y | 600 |
| По X | 1 800 |
Скорость ч/б печати |
|
| A3 | 20 |
| A4 | 36 |
Время выхода первого отпечатка |
|
| Ч/б | 4,5 |
Копир |
|
Макс, количество копий за цикл |
9 999 |
Время выхода первой копии |
4,5 |
Шаг масштабирования |
0,1 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По X | 600 |
| По Y | 600 |
Сканер |
|
Емкость устройства автоподачи оригиналов |
100 |
Слайд-адаптер |
|
Стандарт WIA |
|
Стандарт TWAIN |
|
Отправка изображения по e-mail |
|
Макс. формат оригинала |
A3 |
Тип сканера |
планшетный/протяжный |
Оттенки серого |
256 |
Макс, размер сканирования |
|
| По Y | 432 |
| По X | 297 |
Разрешение сканера |
|
| По Х | 600 |
Скорость сканирования |
|
| Цветн, | 45 |
| Ч/б | 45 |
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
25 000 |
Количество картриджей |
1 |
Ресурс фотобарабана |
110 000 |
Печать на: |
|
| CD/DVD |
|
| Рулоне |
|
| Фотобумаге |
|
| Пленках |
|
| Карточках |
|
| Матовой бумаге |
|
| Конвертах |
|
| Глянцевой бумаге |
|
| Этикетках |
|
Плотность бумаги |
|
| Минимальная | 60 |
| Максимальная | 220 |
Факс |
|
PC Fax |
|
Цветной |
|
Телефон |
|
Caller ID |
|
Проводная трубка |
|
Автоответчик |
|
АОН |
|
Беспроводная трубка |
|
Спикерфон |
|
Стандарт DECT |
|
Шрифты и языки управления |
|
Языки управления |
|
| PCL 5e |
|
| PPDS |
|
|
|
|
| PostScript 2 |
|
| PCL 5c |
|
| PCL 6 |
|
| PostScript 3 |
|
| PostScript |
|
Количество установленных шрифтов |
|
| PCL | 80 |
| PostScript | 137 |
Лотки |
|
Емкость лотка ручной подачи |
150 |
Подача бумаги |
|
| Стандартная | 1 100 |
| Максимальная | 3 600 |
Вывод бумаги |
|
| Стандартный | 250 |
| Максимальный | 3 200 |
Финишер |
|
Брошюровщик |
|
Электронная сортировка |
|
Сортер |
|
Сортировка со сдвигом |
|
Степлер |
|
Интерфейсы |
|
Версия USB |
2,0 |
USB |
|
Веб-интерфейс |
|
Ethernet (RJ-45) |
|
AirPrint |
|
Устройство для чтения карт памяти |
|
RS-232 |
|
Инфракрасный порт |
|
LPT |
|
Bluetooth |
|
Wi-Fi 802.11n |
|
Wi-Fi |
|
FireWire (IEEE 1394) |
|
Память/Процессор |
|
Макс, объем памяти |
4 096 |
Объем памяти |
2 048 |
Емкость жесткого диска |
250 |
Частота процессора |
1 200 |
Процессор |
|
Дополнительная информация |
|
Экран |
|
Работа от аккумулятора |
|
Поддержка ОС |
|
| DOS |
|
| Windows |
|
| Linux |
|
| Mac OS |
|
Потребляемая мощность |
|
| При работе | 1 500 |
Габариты |
|
Вес |
56,5 |
Высота |
735 |
Ширина |
585 |
Глубина |
660 |
Модули
BYPASS TRAY SECTION
1ST PAPER FEED SECTION
ELECTRICAL COMPONENTS 2
2ND PAPER FEED SECTION 2
VERTICAL CONVEYANCE DOOR SECTION
EXTERNAL PARTS 2
CASSETTE RAIL SECTION
PH UNIT, HIGH VOLTAGE SECTION
REVERSAL SECTION
PAPER FEED SECTION
TONER SUPPLY SECTION 2
SCANNER SECTION 2
PAPER EXIT SECTION 2
FUSING SECTION
OZONE DUCT SECTION
PAPER SIZE DETECTION SECTION
SCANNER SECTION
VERTICAL TRANSPORT SECTION
MAIN POWER SUPPLY SECTION
BYPASS TRAY SECTION 2
2ND CASSETTE SECTION
1ST PAPER FEED SECTION 2
REGISTRATION SECTION
ELECTRICAL COMPONENTS
PAPER EXIT SECTION
TONER SUPPLY SECTION
ERASE LAMP, DV LOCK LEVER SECTION
2ND CASSETTE SECTION 2
INNER COVER SECTION
1ST CASSETTE SECTION
1ST CASSETTE SECTION 2
OPERATION PANEL SECTION
SCANNER SECTION 3
2ND PAPER FEED SECTION
EXTERNAL PARTS
VERTICAL TRANSPORT SECTION 2
DRIVE SECTION
REVERSAL SECTION 2
Детали EXTERNAL PARTS 2
| Деталь: | Multiple Bypass Tray Assy |
| Парткод: | A7AHR71600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH600400 |
| Деталь: | Guide Sheet |
| Парткод: | A7AH605200 |
| Деталь: | HOLDER |
| Парткод: | A7AH600300 |
| Деталь: | Paper feed Shaft |
| Парткод: | A7AH601100 |
| Деталь: | Slide Stopper |
| Парткод: | A161594400 |
| Деталь: | ROLLER |
| Парткод: | A00F623201 |
| Деталь: | BUSHING |
| Парткод: | A02E596300 |
| Деталь: | SHAFT |
| Парткод: | A7AH602701 |
| Деталь: | Paper feed Cam |
| Парткод: | A161593300 |
| Деталь: | Drive Frame |
| Парткод: | A7AH600502 |
| Деталь: | Bypass Cover |
| Парткод: | A7AH605100 |
| Деталь: | BUSHING |
| Парткод: | 1134304301 |
| Деталь: | GEAR 20T |
| Парткод: | A7AH603000 |
| Деталь: | Bypass Gear |
| Парткод: | A7AH602200 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH604101 |
| Деталь: | COVER |
| Парткод: | A7AH604300 |
| Деталь: | CONVEYANCE SOLENOID |
| Парткод: | A034M20100 |
| Деталь: | CLUTCH |
| Парткод: | A7AHM20400 |
| Деталь: | Drive Cover |
| Парткод: | A7AH600801 |
| Деталь: | SEAL |
| Парткод: | A7AH604900 |
| Деталь: | LEVER |
| Парткод: | A7AH603100 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH603200 |
| Деталь: | CLUTCH ASSY |
| Парткод: | A7AHR72700 |
| Деталь: | GEAR 24T |
| Парткод: | A7AH604700 |
| Деталь: | CLUTCH |
| Парткод: | A7AHM20500 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | Positioning Shaft |
| Парткод: | A7AH565100 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH566001 |
| Деталь: | Paper feed Frame |
| Парткод: | A7AH565301 |
| Деталь: | Frame /Front |
| Парткод: | A7AH560101 |
| Деталь: | Conveyance Guide |
| Парткод: | A7AH565702 |
| Деталь: | Detecting Lever |
| Парткод: | A7AH561601 |
| Деталь: | Shaft /Paper feed |
| Парткод: | A7AH560500 |
| Деталь: | Paper feed Gear |
| Парткод: | A7AH562400 |
| Деталь: | CLUTCH |
| Парткод: | A02E561100 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | ROLLER |
| Парткод: | A5C1562200 |
| Деталь: | Conveyance Gear 28T |
| Парткод: | A7AH562600 |
| Деталь: | Idling Gear |
| Парткод: | A7AH562300 |
| Деталь: | Support Shaft |
| Парткод: | A7AH563400 |
| Деталь: | Protection Sheet |
| Парткод: | A7AH562900 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH562801 |
| Деталь: | Conveyance Guide /4 |
| Парткод: | A7AH562100 |
| Деталь: | Harness /Paperfeed |
| Парткод: | A7AHN12100 |
| Деталь: | Frame /Rear |
| Парткод: | A7AH560201 |
| Деталь: | Protection Seal |
| Парткод: | A7AH569500 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | COVER |
| Парткод: | A7AH132801 |
| Деталь: | Harness /Paper feed |
| Парткод: | A7AHN14600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH132600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH132200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH132300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH132900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH132400 |
| Деталь: | SEESAW-SWITCH |
| Парткод: | 4038M60000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH132701 |
| Деталь: | Harness /AC Power source |
| Парткод: | A7AHN10201 |
| Деталь: | FERRITECORE |
| Парткод: | A02EM70F00 |
| Деталь: | FRAME |
| Парткод: | A7AH563902 |
| Деталь: | Paper feed Guide |
| Парткод: | A7AH578401 |
| Деталь: | GUIDE |
| Парткод: | A7AH568500 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7AH569400 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH568700 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A0ED563900 |
| Деталь: | Support Shaft |
| Парткод: | A7AH565000 |
| Деталь: | HOLDER |
| Парткод: | A7AH563101 |
| Деталь: | Release Lever |
| Парткод: | A7AH564101 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH564401 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH561300 |
| Деталь: | BUSHING |
| Парткод: | A02E815200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH566100 |
| Деталь: | LOCK CLAW |
| Парткод: | A0ED712100 |
| Деталь: | SENSOR LEVER |
| Парткод: | A7AH705201 |
| Деталь: | Open/close Handle |
| Парткод: | A7AH706700 |
| Деталь: | PIN |
| Парткод: | A7AH705301 |
| Деталь: | Lock plate |
| Парткод: | A7AH706000 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH705700 |
| Деталь: | Lock Claw /Lower |
| Парткод: | A7AH706500 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161815900 |
| Деталь: | Paper feed Guide |
| Парткод: | A7AH705401 |
| Деталь: | Paper feed Guide |
| Парткод: | A7AH600700 |
| Деталь: | Positioning Part |
| Парткод: | A7AH706300 |
| Деталь: | HOLDER |
| Парткод: | A7AH706400 |
| Деталь: | GUIDE |
| Парткод: | A7AH138200 |
| Деталь: | HOLDER |
| Парткод: | A7AH706201 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A161137100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161151200 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06M60100 |
| Деталь: | HOLDER |
| Парткод: | A7AH705501 |
| Деталь: | ROLL |
| Парткод: | A161815400 |
| Деталь: | Pulling Spring |
| Парткод: | A161815500 |
| Деталь: | SHAFT |
| Парткод: | A161815300 |
| Деталь: | Lock Claw /Middle |
| Парткод: | A7AH706600 |
| Деталь: | Open/close Claw |
| Парткод: | A7AH705800 |
| Деталь: | Swing Spring |
| Парткод: | A161815800 |
| Деталь: | HOLDER |
| Парткод: | A7AH705900 |
| Деталь: | Adjusting Plate |
| Парткод: | A7AH706101 |
| Деталь: | COVER |
| Парткод: | A7AH164600 |
| Деталь: | COVER |
| Парткод: | A7AH162802 |
| Деталь: | COVER |
| Парткод: | A7AH162902 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH167001 |
| Деталь: | COVER |
| Парткод: | A7AH162400 |
| Деталь: | Cover Plate /Right rear |
| Парткод: | A7AH163001 |
| Деталь: | Cover Plate /Upper |
| Парткод: | A7AH160503 |
| Деталь: | Cover Plate /Right rear |
| Парткод: | A7AH163300 |
| Деталь: | FILTER |
| Парткод: | A7AH141400 |
| Деталь: | LABEL |
| Парткод: | A2X0945701 |
| Деталь: | Cover Plate /Lower |
| Парткод: | A7AH164701 |
| Деталь: | Cover Plate /Lower |
| Парткод: | A7AH163402 |
| Деталь: | GASKET |
| Парткод: | A7AHM92000 |
| Деталь: | GASKET |
| Парткод: | A7AHM92100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH101600 |
| Деталь: | Mounting Plate /Right rear |
| Парткод: | A7AH102000 |
| Деталь: | SHAFT |
| Парткод: | A7AH101900 |
| Деталь: | LEVER |
| Парткод: | A161101900 |
| Деталь: | COVER |
| Парткод: | A7AH102300 |
| Деталь: | RUBBER FOOT |
| Парткод: | 996305501 |
| Деталь: | RAIL |
| Парткод: | A7AH103000 |
| Деталь: | STOPPER |
| Парткод: | A7AH120102 |
| Деталь: | STOPPER |
| Парткод: | A7AH121301 |
| Деталь: | SEAL |
| Парткод: | A1UD104500 |
| Деталь: | CONTACT ASSY |
| Парткод: | A7AHR70100 |
| Деталь: | DV Contact Assy |
| Парткод: | A7AHR70000 |
| Деталь: | Harness /Separating |
| Парткод: | A7AHN10800 |
| Деталь: | Harness /Transfer |
| Парткод: | A7AHN10500 |
| Деталь: | Harness /HV |
| Парткод: | A7AHN13800 |
| Деталь: | PCB Support |
| Парткод: | V502010043 |
| Деталь: | Harness /Developing |
| Парткод: | A7AHN10600 |
| Деталь: | HIGH VOLTAGE UNIT |
| Парткод: | A7AHM40600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH134200 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | A891R70000 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4128197801 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4128197901 |
| Деталь: | Harness /Chaging |
| Парткод: | A7AHN10700 |
| Деталь: | Harness /HV |
| Парткод: | A7AHN13900 |
| Деталь: | Cover /Upper |
| Парткод: | A7AH813200 |
| Деталь: | Stench filter Assy |
| Парткод: | A7AHR71800 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH705600 |
| Деталь: | Door /Upper |
| Парткод: | A7AH705001 |
| Деталь: | Label Paper supply |
| Парткод: | A7AH943000 |
| Деталь: | SEAL |
| Парткод: | A7AH709000 |
| Деталь: | Door /Lower |
| Парткод: | A7AH705100 |
| Деталь: | Knob /A |
| Парткод: | A161814700 |
| Деталь: | Label M4 |
| Парткод: | A7AH944200 |
| Деталь: | BUSHING |
| Парткод: | A02E815200 |
| Деталь: | Idler Roller /A |
| Парткод: | A161825700 |
| Деталь: | Roller /B |
| Парткод: | A7AH814000 |
| Деталь: | Ground Contact |
| Парткод: | A7AH813600 |
| Деталь: | COVER |
| Парткод: | A7AH814901 |
| Деталь: | Gear 23T |
| Парткод: | A7AH814700 |
| Деталь: | Gear 23T |
| Парткод: | A7AH814600 |
| Деталь: | ROLL |
| Парткод: | A7AH815601 |
| Деталь: | COLLAR |
| Парткод: | A7AH814800 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038218401 |
| Деталь: | Drive plate |
| Парткод: | A7AH814200 |
| Деталь: | Belt 222L |
| Парткод: | A7AH814500 |
| Деталь: | Pulley 22/27T |
| Парткод: | A7AH814400 |
| Деталь: | Belt 112L |
| Парткод: | A7AH814300 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH815700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH815500 |
| Деталь: | Drive Side plate |
| Парткод: | A7AH814100 |
| Деталь: | Stepping motor |
| Парткод: | A7AHM10700 |
| Деталь: | Guide /Upper |
| Парткод: | A7AH813100 |
| Деталь: | DUCT |
| Парткод: | A7AH145401 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | FAN MOTOR |
| Парткод: | 4556M10000 |
| Деталь: | CUSHION |
| Парткод: | A7AH892300 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH568900 |
| Деталь: | Open/close Lever |
| Парткод: | A7AH568800 |
| Деталь: | PAPER FEED ASSY |
| Парткод: | A7AHR71300 |
| Деталь: | COVER |
| Парткод: | A7AH133300 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140051 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | GEAR 20T |
| Парткод: | A7AH218100 |
| Деталь: | Gear 15/37T |
| Парткод: | A7AH218300 |
| Деталь: | Drive Holder |
| Парткод: | A7AH218702 |
| Деталь: | Gear 15/20T |
| Парткод: | A7AH218400 |
| Деталь: | SHAFT |
| Парткод: | A7AH218500 |
| Деталь: | Fixing Claw |
| Парткод: | A161165700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A2XN374800 |
| Деталь: | HOLDER |
| Парткод: | A7AH362700 |
| Деталь: | SHEET |
| Парткод: | A7AH165200 |
| Деталь: | LEVER |
| Парткод: | A7AH285102 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH285400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH285501 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | APS Photoreflector |
| Парткод: | A7AHM50100 |
| Деталь: | Ground Plate spring |
| Парткод: | A7AH281701 |
| Деталь: | Harness /Scanner |
| Парткод: | A7AHN12W00 |
| Деталь: | Mounting Plate /Right front |
| Парткод: | A7AH262602 |
| Деталь: | Mounting Plate /Right front |
| Парткод: | A7AH261401 |
| Деталь: | SEAL |
| Парткод: | 4581162501 |
| Деталь: | Harness /ADF Relay |
| Парткод: | A7AHN12800 |
| Деталь: | Ground Plate spring |
| Парткод: | A7AH262501 |
| Деталь: | Neutralizing Brush |
| Парткод: | A161894000 |
| Деталь: | GUIDE |
| Парткод: | A7AH890300 |
| Деталь: | ROLL |
| Парткод: | A7AH892000 |
| Деталь: | COLLAR |
| Парткод: | A7AH891901 |
| Деталь: | ROLLER |
| Парткод: | A7AH891000 |
| Деталь: | Ground Contact /Lower |
| Парткод: | A7AH895601 |
| Деталь: | PULLEY |
| Парткод: | A7AH811100 |
| Деталь: | ROLL |
| Парткод: | 4004590301 |
| Деталь: | SHAFT |
| Парткод: | 4025598401 |
| Деталь: | SPRING |
| Парткод: | A161892400 |
| Деталь: | GROUND SPRING |
| Парткод: | A7AH811300 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 1164202801 |
| Деталь: | BUSHING |
| Парткод: | A0ED891100 |
| Деталь: | Ground Contact /Upper |
| Парткод: | A7AH811500 |
| Деталь: | GUIDE |
| Парткод: | A7AH810102 |
| Деталь: | GROUND SPRING |
| Парткод: | A7AH891500 |
| Деталь: | COLLAR |
| Парткод: | A0ED897700 |
| Деталь: | ROLL |
| Парткод: | A1UD721500 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH891800 |
| Деталь: | Paper exit Guide |
| Парткод: | A7AH812002 |
| Деталь: | COVER |
| Парткод: | A7AH892200 |
| Деталь: | BUSHING |
| Парткод: | A161891000 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH890800 |
| Деталь: | SOLENOID ASSY |
| Парткод: | A7AHR72500 |
| Деталь: | COVER |
| Парткод: | A7AH890700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH890900 |
| Деталь: | Panel /Front |
| Парткод: | A7AH890402 |
| Деталь: | CUSHION |
| Парткод: | A7AH892300 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A1UD722700 |
| Деталь: | SHAFT |
| Парткод: | A7AH892101 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH890200 |
| Деталь: | Panel /Rear |
| Парткод: | A7AH890501 |
| Деталь: | Gear 21/35T |
| Парткод: | A7AH891200 |
| Деталь: | GEAR 18T |
| Парткод: | A7AH891700 |
| Деталь: | Drive Holder |
| Парткод: | A7AH891400 |
| Деталь: | GEAR 24T |
| Парткод: | A02F897200 |
| Деталь: | GEAR 16T |
| Парткод: | A7AH891300 |
| Деталь: | GUIDE |
| Парткод: | A7AH890102 |
| Деталь: | Cushion /B |
| Парткод: | A161826000 |
| Деталь: | SEAL |
| Парткод: | A7AH819900 |
| Деталь: | SEAL |
| Парткод: | A7AH819700 |
| Деталь: | Harness /Fixing Relay |
| Парткод: | A7AHN10401 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH134500 |
| Деталь: | COVER |
| Парткод: | A7AH133201 |
| Деталь: | COVER |
| Парткод: | A7AH133100 |
| Деталь: | Fusing Unit /220-240V |
| Парткод: | A7AHR72400 |
| Деталь: | FERRITECORE |
| Парткод: | A7AHM90300 |
| Деталь: | GUIDE RAIL |
| Парткод: | A7AH115101 |
| Деталь: | SEAL |
| Парткод: | A7AH146600 |
| Деталь: | DUCT |
| Парткод: | A7AH145100 |
| Деталь: | SEAL |
| Парткод: | A7AH135100 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH101102 |
| Деталь: | GROUND PLATE |
| Парткод: | A7AH139101 |
| Деталь: | Stay /Rear |
| Парткод: | A7AH101201 |
| Деталь: | DUCT |
| Парткод: | A7AH147100 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | DUCT |
| Парткод: | A7AH145201 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | TONER FILTER |
| Парткод: | A7AHR72600 |
| Деталь: | SEAL |
| Парткод: | A7AH146800 |
| Деталь: | HOLDER |
| Парткод: | A7AH146100 |
| Деталь: | DUCT |
| Парткод: | A7AH146301 |
| Деталь: | SEAL |
| Парткод: | A7AH146500 |
| Деталь: | WtoW Connector |
| Парткод: | V651010045 |
| Деталь: | LEVER |
| Парткод: | A7AH627501 |
| Деталь: | SPRING |
| Парткод: | A7AH627701 |
| Деталь: | STOPPER |
| Парткод: | A7AH627900 |
| Деталь: | SPRING |
| Парткод: | A7AH627800 |
| Деталь: | SWITCH |
| Парткод: | A7AHM60100 |
| Деталь: | Paper Size Detection Assy |
| Парткод: | A7AHR72800 |
| Деталь: | Harness /Paper Feed Wiring |
| Парткод: | A7AHN12200 |
| Деталь: | COVER |
| Парткод: | A7AH627600 |
| Деталь: | Case |
| Парткод: | A7AH627400 |
| Деталь: | MOTOR |
| Парткод: | 9J06M10300 |
| Деталь: | Read Cover /Rear |
| Парткод: | A7AH266203 |
| Деталь: | Read Cover /Rear |
| Парткод: | A7AH267000 |
| Деталь: | SEAL |
| Парткод: | A7AH266800 |
| Деталь: | IR Cover /Upper Assy |
| Парткод: | A7AHR70800 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7AH267201 |
| Деталь: | COVER |
| Парткод: | A7AH266300 |
| Деталь: | LABEL |
| Парткод: | A0HF952400 |
| Деталь: | Read Cover /Front |
| Парткод: | A7AH266503 |
| Деталь: | Read Cover /Left |
| Парткод: | A7AH266601 |
| Деталь: | Vertical Transport Assy |
| Парткод: | A7AHR71900 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A7AH707700 |
| Деталь: | SEAL |
| Парткод: | A7AH708200 |
| Деталь: | HOLDER |
| Парткод: | A7AH704500 |
| Деталь: | CONTACT |
| Парткод: | A7AH704400 |
| Деталь: | CONTACT |
| Парткод: | A7AH703600 |
| Деталь: | CONTACT |
| Парткод: | A7AH700401 |
| Деталь: | CONTACT |
| Парткод: | A7AH700500 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH707600 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030420701 |
| Деталь: | HOLDER |
| Парткод: | A7AH703401 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7AH708800 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH701901 |
| Деталь: | THERMISTOR |
| Парткод: | 9372271022 |
| Деталь: | NEUTRALIZING NEEDLE |
| Парткод: | 1164420204 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7AH817700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH816701 |
| Деталь: | COVER |
| Парткод: | A7AH817000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH816300 |
| Деталь: | HOLDER |
| Парткод: | A7AH703500 |
| Деталь: | Conveyance Holder |
| Парткод: | A7AH700101 |
| Деталь: | SEAL |
| Парткод: | A7AH708500 |
| Деталь: | FIXED POWER RESISTORS |
| Парткод: | V800500300 |
| Деталь: | Guide Sheet |
| Парткод: | A7AH709900 |
| Деталь: | SEAL |
| Парткод: | A7AH141300 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | PROTECTION |
| Парткод: | 1154467001 |
| Деталь: | DUCT |
| Парткод: | A7AH141100 |
| Деталь: | Power supply Assy /220-240V |
| Парткод: | A7AHR70600 |
| Деталь: | Label Metric |
| Парткод: | A7AH943100 |
| Деталь: | Brake Part |
| Парткод: | A7AH604501 |
| Деталь: | Regulating Plate /R |
| Парткод: | A7AH601901 |
| Деталь: | FRICTION SHEET |
| Парткод: | 978381101 |
| Деталь: | Regulating Plate /L |
| Парткод: | A7AH602001 |
| Деталь: | Brake Part /F |
| Парткод: | A7AH604401 |
| Деталь: | Auxiliary Tray |
| Парткод: | A161592200 |
| Деталь: | TRAY |
| Парткод: | A7AH600102 |
| Деталь: | GEAR 20T |
| Парткод: | A02E592100 |
| Деталь: | FRICTION PLATE |
| Парткод: | A161593800 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH603300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH601700 |
| Деталь: | Support Holder |
| Парткод: | A7AH604202 |
| Деталь: | CUSHION |
| Парткод: | A161594201 |
| Деталь: | SEAL |
| Парткод: | A161595100 |
| Деталь: | HOLD PLATE |
| Парткод: | A161591600 |
| Деталь: | Slide Guide |
| Парткод: | A161595600 |
| Деталь: | FRAME |
| Парткод: | A7AH600601 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4658015106 |
| Деталь: | Holding |
| Парткод: | A7AH601300 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030347501 |
| Деталь: | HOLD PLATE |
| Парткод: | A7AH601400 |
| Деталь: | GUIDE |
| Парткод: | A02E597600 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Harness /Paper feed |
| Парткод: | A7AHN11901 |
| Деталь: | Separating Plate |
| Парткод: | A161595300 |
| Деталь: | GUIDE |
| Парткод: | 4030340301 |
| Деталь: | Sensor Holder |
| Парткод: | A161591100 |
| Деталь: | TORSION SPRING |
| Парткод: | A161591000 |
| Деталь: | ACTUATOR |
| Парткод: | A7AH601202 |
| Деталь: | VR |
| Парткод: | A161M50400 |
| Деталь: | Harness /Paper Detection |
| Парткод: | A7AHN13200 |
| Деталь: | Regulating Gear 41T |
| Парткод: | A161594300 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH603400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AHR71700 |
| Деталь: | LIFTING PLATE |
| Парткод: | A7AH600203 |
| Деталь: | 2nd Cassette Assy |
| Парткод: | A7AHR71500 |
| Деталь: | ROLL |
| Парткод: | A7AH629901 |
| Деталь: | Slide Part |
| Парткод: | A7AH622901 |
| Деталь: | RAIL |
| Парткод: | A7AH623400 |
| Деталь: | LEVER |
| Парткод: | A7AH624200 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161626800 |
| Деталь: | LEVER |
| Парткод: | A161626602 |
| Деталь: | Label 2 |
| Парткод: | A7AH941200 |
| Деталь: | HANDLE |
| Парткод: | A7AH626901 |
| Деталь: | Cover /Lower |
| Парткод: | A7AH625200 |
| Деталь: | HOLDER |
| Парткод: | A7AH624300 |
| Деталь: | Label Paper supply |
| Парткод: | A7AH941000 |
| Деталь: | Paper feed Cassette |
| Парткод: | A7AH630102 |
| Деталь: | ROLL |
| Парткод: | A161623400 |
| Деталь: | Rail /Left |
| Парткод: | A7AH623201 |
| Деталь: | FRAME |
| Парткод: | A7AH563902 |
| Деталь: | Paper feed Guide |
| Парткод: | A7AH568402 |
| Деталь: | ACTUATOR |
| Парткод: | A7AH560800 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A7AH560700 |
| Деталь: | GUIDE |
| Парткод: | A7AH568500 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7AH569400 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH568600 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A0ED563900 |
| Деталь: | Support Shaft |
| Парткод: | A7AH565000 |
| Деталь: | HOLDER |
| Парткод: | A7AH563101 |
| Деталь: | Release Lever |
| Парткод: | A7AH564101 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH564401 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH561300 |
| Деталь: | BUSHING |
| Парткод: | A02E815200 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH570100 |
| Деталь: | Cushion /B |
| Парткод: | A161826000 |
| Деталь: | Slide Part |
| Парткод: | A7AH570200 |
| Деталь: | CLUTCH |
| Парткод: | A02EM20200 |
| Деталь: | BUSHING |
| Парткод: | A7AH703201 |
| Деталь: | Registration Spring |
| Парткод: | A7AH703301 |
| Деталь: | HOLDER |
| Парткод: | A7AH706902 |
| Деталь: | Mounting Screw |
| Парткод: | A7AH708900 |
| Деталь: | PLATE NUT |
| Парткод: | 4002504202 |
| Деталь: | Image Transfer Roller Kit |
| Парткод: | A7AHR72900 |
| Деталь: | Registration Roller |
| Парткод: | A7AH703001 |
| Деталь: | LEVER |
| Парткод: | A7AH708600 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH708700 |
| Деталь: | GUIDE |
| Парткод: | 4038353701 |
| Деталь: | Registration Roller |
| Парткод: | A7AH703101 |
| Деталь: | GUIDE |
| Парткод: | 4038353901 |
| Деталь: | Guide Sheet |
| Парткод: | A0ED700600 |
| Деталь: | GEAR 18T |
| Парткод: | A7AH707500 |
| Деталь: | GEAR 13T |
| Парткод: | 1164351501 |
| Деталь: | GROUND PLATE |
| Парткод: | A7AH702200 |
| Деталь: | HOLDER |
| Парткод: | A7AH707403 |
| Деталь: | Guide Sheet /Inside |
| Парткод: | A7AH704101 |
| Деталь: | Registration Guide /Inside |
| Парткод: | A7AH702002 |
| Деталь: | Harness /Conveyance |
| Парткод: | A7AHN12400 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Ground Contact |
| Парткод: | A7AH708100 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH707300 |
| Деталь: | Spring /A |
| Парткод: | A161701100 |
| Деталь: | Registration Actuator |
| Парткод: | A7AH701700 |
| Деталь: | Paper Powder Removal Assy |
| Парткод: | A7AHR72100 |
| Деталь: | Registration Guide /Outside |
| Парткод: | A7AH702101 |
| Деталь: | SHAFT |
| Парткод: | A7AH709200 |
| Деталь: | SPACER |
| Парткод: | V502010036 |
| Деталь: | Insulating Part |
| Парткод: | A7AH130600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH131100 |
| Деталь: | SHIELD PLATE |
| Парткод: | A7AH130300 |
| Деталь: | PWB Assembly (PWB-MFP) |
| Парткод: | A7AHH02005 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH130201 |
| Деталь: | Harness /DC Power source |
| Парткод: | A7AHN10902 |
| Деталь: | HOLDER |
| Парткод: | A7AH139301 |
| Деталь: | DUCT |
| Парткод: | A7AH141201 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH130101 |
| Деталь: | FERRITECORE |
| Парткод: | A3EWM90300 |
| Деталь: | PWB Assembly(PWB-EE) |
| Парткод: | A7AHH00C00 |
| Деталь: | GUIDE |
| Парткод: | A7AH138101 |
| Деталь: | FERRITECORE |
| Парткод: | A49FM90100 |
| Деталь: | FERRITECORE |
| Парткод: | A3EWM90200 |
| Деталь: | Harness /Control |
| Парткод: | A7AHN15A00 |
| Деталь: | Connector Cover |
| Парткод: | V503010002 |
| Деталь: | SCREW |
| Парткод: | A7AH131300 |
| Деталь: | COVER |
| Парткод: | A7AH810201 |
| Деталь: | SHEET |
| Парткод: | A161894100 |
| Деталь: | Neutralizing Brush |
| Парткод: | A161894000 |
| Деталь: | COVER |
| Парткод: | A7AH162700 |
| Деталь: | Timing belt 164L |
| Парткод: | A7AH811200 |
| Деталь: | GUIDE PART |
| Парткод: | A161897200 |
| Деталь: | Stepping motor |
| Парткод: | A7AHM10700 |
| Деталь: | COVER |
| Парткод: | A7AH405200 |
| Деталь: | Seal /1 |
| Парткод: | A161404001 |
| Деталь: | SEAL |
| Парткод: | A161403701 |
| Деталь: | Seal /2 |
| Парткод: | A161404100 |
| Деталь: | SPACER |
| Парткод: | A161403901 |
| Деталь: | Label Toner 1 |
| Парткод: | A0ED940600 |
| Деталь: | LABEL TONER TYPE |
| Парткод: | A7AH946200 |
| Деталь: | SHUTTER |
| Парткод: | A161402403 |
| Деталь: | SEAL |
| Парткод: | A161403800 |
| Деталь: | SEAL |
| Парткод: | A161402502 |
| Деталь: | COVER |
| Парткод: | A7AH402100 |
| Деталь: | SEAL |
| Парткод: | A7AH403300 |
| Деталь: | SEAL |
| Парткод: | A7AH403500 |
| Деталь: | SCREW |
| Парткод: | A7AH400100 |
| Деталь: | Conveyance Pipe |
| Парткод: | A7AH406000 |
| Деталь: | SEAL |
| Парткод: | A7AH403200 |
| Деталь: | SHUTTER |
| Парткод: | A0ED401000 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH406300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH400700 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Detecting Actuator |
| Парткод: | A7AH404300 |
| Деталь: | PIN |
| Парткод: | A161400800 |
| Деталь: | BUSHING |
| Парткод: | 4163510201 |
| Деталь: | GEAR 36T |
| Парткод: | A161401100 |
| Деталь: | Gear 17/65T |
| Парткод: | A7AH401300 |
| Деталь: | Fixing Plate |
| Парткод: | A7AH406201 |
| Деталь: | Stepping motor |
| Парткод: | A7AHM10400 |
| Деталь: | GEAR 18T |
| Парткод: | A161401000 |
| Деталь: | SEAL |
| Парткод: | 4576536301 |
| Деталь: | HOLDER |
| Парткод: | A161403101 |
| Деталь: | Agitating Shaft |
| Парткод: | A5C1F42000 |
| Деталь: | DETECTING PLATE |
| Парткод: | A161400401 |
| Деталь: | Fixing Plate |
| Парткод: | A161404200 |
| Деталь: | Detecting Seal |
| Парткод: | A161400601 |
| Деталь: | Sub Hopper Assy |
| Парткод: | A7AHR71100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH142300 |
| Деталь: | Wiring Cover |
| Парткод: | A7AH138600 |
| Деталь: | SEAL |
| Парткод: | A7AH142900 |
| Деталь: | SEAL |
| Парткод: | A7AH142800 |
| Деталь: | LED Unit |
| Парткод: | A1UDM30900 |
| Деталь: | SEAL |
| Парткод: | A7AH142700 |
| Деталь: | HOLDER |
| Парткод: | A7AH142100 |
| Деталь: | Light blocking Plate |
| Парткод: | A7AH136301 |
| Деталь: | Sensor Holder |
| Парткод: | A7AH112300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH139900 |
| Деталь: | Relay Connector |
| Парткод: | A0EDM60001 |
| Деталь: | LABEL |
| Парткод: | A02E940300 |
| Деталь: | GUIDE RAIL |
| Парткод: | A7AH112102 |
| Деталь: | OZONE FILTER |
| Парткод: | A7AHR70300 |
| Деталь: | Harness /Photoconductor |
| Парткод: | A7AHN11401 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A7AH139700 |
| Деталь: | HOLDER |
| Парткод: | A161115700 |
| Деталь: | Slide Lever |
| Парткод: | A7AH116100 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A7AH116900 |
| Деталь: | Release Shaft |
| Парткод: | A7AH116300 |
| Деталь: | Slide Lever |
| Парткод: | A161116100 |
| Деталь: | Release Lever |
| Парткод: | A7AH116500 |
| Деталь: | Harness /Neutralizing |
| Парткод: | A7AHN11301 |
| Деталь: | Lifting Shaft |
| Парткод: | A7AH621601 |
| Деталь: | LEVER |
| Парткод: | A7AH623601 |
| Деталь: | GROUND SPRING |
| Парткод: | A7AH622100 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A7AH620902 |
| Деталь: | CUSHION |
| Парткод: | A161624100 |
| Деталь: | Operation Lever |
| Парткод: | A7AH621300 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH621000 |
| Деталь: | LOCK LEVER |
| Парткод: | A7AH621200 |
| Деталь: | LABEL |
| Парткод: | A161943000 |
| Деталь: | REGULATING PLATE |
| Парткод: | A7AH620801 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7AH628200 |
| Деталь: | GEAR |
| Парткод: | A161620701 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A7AH622401 |
| Деталь: | GUIDE |
| Парткод: | A7AH629600 |
| Деталь: | LEVER |
| Парткод: | 4030320601 |
| Деталь: | Label Position |
| Парткод: | A7AH941300 |
| Деталь: | REGULATING PLATE |
| Парткод: | A7AH621701 |
| Деталь: | LEVER |
| Парткод: | A7AH623500 |
| Деталь: | Adjusting Plate |
| Парткод: | A7AH620600 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | LEVER |
| Парткод: | A7AH621401 |
| Деталь: | PLATE SPRING |
| Парткод: | A7AH621801 |
| Деталь: | LIFTING PLATE |
| Парткод: | A7AH620400 |
| Деталь: | Separating Sheet |
| Парткод: | A7AH627000 |
| Деталь: | DETECTING PLATE |
| Парткод: | A7AH622201 |
| Деталь: | BUSHING |
| Парткод: | A7AH621501 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | STOPPER |
| Парткод: | A7AH112600 |
| Деталь: | Cover /Front |
| Парткод: | A7AH165003 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038101401 |
| Деталь: | HOLDER |
| Парткод: | A7AH112900 |
| Деталь: | LEVER |
| Парткод: | A7AH112500 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH113000 |
| Деталь: | STOPPER |
| Парткод: | A7AH112800 |
| Деталь: | Release Lever |
| Парткод: | A7AH116200 |
| Деталь: | Cover /Rear |
| Парткод: | A7AH164500 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A7AHM50400 |
| Деталь: | COVER |
| Парткод: | A7AH135301 |
| Деталь: | SPEAKER |
| Парткод: | A0P0M73100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7AH138900 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161151300 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06M60100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH138500 |
| Деталь: | LEVER |
| Парткод: | A7AH138700 |
| Деталь: | TORSION SPRING |
| Парткод: | A7AH138800 |
| Деталь: | 1st Cassette Assy |
| Парткод: | A7AHR71400 |
| Деталь: | ROLL |
| Парткод: | A7AH629901 |
| Деталь: | Slide Part |
| Парткод: | A7AH622901 |
| Деталь: | RAIL |
| Парткод: | A7AH623400 |
| Деталь: | LEVER |
| Парткод: | A7AH624100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161626800 |
| Деталь: | LEVER |
| Парткод: | A161626602 |
| Деталь: | Label 1 |
| Парткод: | A7AH941100 |
| Деталь: | HANDLE |
| Парткод: | A7AH626901 |
| Деталь: | Cover /Upper |
| Парткод: | A7AH625101 |
| Деталь: | HOLDER |
| Парткод: | A7AH624300 |
| Деталь: | Label Paper supply |
| Парткод: | A7AH941000 |
| Деталь: | Paper feed Cassette |
| Парткод: | A7AH620103 |
| Деталь: | ROLL |
| Парткод: | A161623400 |
| Деталь: | Rail /Left |
| Парткод: | A7AH623201 |
| Деталь: | Lifting Shaft |
| Парткод: | A7AH621601 |
| Деталь: | LEVER |
| Парткод: | A7AH623601 |
| Деталь: | GROUND SPRING |
| Парткод: | A7AH622100 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A7AH620902 |
| Деталь: | CUSHION |
| Парткод: | A161624100 |
| Деталь: | Operation Lever |
| Парткод: | A7AH621300 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH621000 |
| Деталь: | LOCK LEVER |
| Парткод: | A7AH621200 |
| Деталь: | LABEL |
| Парткод: | A161943000 |
| Деталь: | REGULATING PLATE |
| Парткод: | A7AH620801 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7AH628200 |
| Деталь: | GEAR |
| Парткод: | A161620701 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A7AH622401 |
| Деталь: | GUIDE |
| Парткод: | A7AH629600 |
| Деталь: | LEVER |
| Парткод: | 4030320601 |
| Деталь: | Label Position |
| Парткод: | A7AH941300 |
| Деталь: | REGULATING PLATE |
| Парткод: | A7AH621701 |
| Деталь: | LEVER |
| Парткод: | A7AH623500 |
| Деталь: | Adjusting Plate |
| Парткод: | A7AH620600 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | LEVER |
| Парткод: | A7AH621401 |
| Деталь: | PLATE SPRING |
| Парткод: | A7AH621801 |
| Деталь: | LIFTING PLATE |
| Парткод: | A7AH620400 |
| Деталь: | Separating Sheet |
| Парткод: | A7AH627000 |
| Деталь: | DETECTING PLATE |
| Парткод: | A7AH622201 |
| Деталь: | BUSHING |
| Парткод: | A7AH621501 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | GROUND PLATE |
| Парткод: | A7AH134600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH139000 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A7AHN15600 |
| Деталь: | HOLDER |
| Парткод: | A7AH162100 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A7AHM70101 |
| Деталь: | SEAL |
| Парткод: | A7AH162001 |
| Деталь: | COVER |
| Парткод: | A7AH161900 |
| Деталь: | LENS |
| Парткод: | A7AH161801 |
| Деталь: | COVER |
| Парткод: | A7AH166601 |
| Деталь: | PLATE NUT |
| Парткод: | 4002504202 |
| Деталь: | Cover /Right |
| Парткод: | A7AH161501 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH139401 |
| Деталь: | Cover /Front |
| Парткод: | A7AH161700 |
| Деталь: | Cover /Middle |
| Парткод: | A7AH161602 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A7AHN15301 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH139600 |
| Деталь: | Cover /Left |
| Парткод: | A7AH161400 |
| Деталь: | Scan-IR unit |
| Парткод: | A890R70011 |
| Деталь: | Harness /Scanner |
| Парткод: | A7AHN12Y02 |
| Деталь: | LED exposure unit |
| Парткод: | A890R70200 |
| Деталь: | Guide Sheet |
| Парткод: | A7AH262900 |
| Деталь: | Mounting Cover |
| Парткод: | A7AH262100 |
| Деталь: | Harness /Scanner |
| Парткод: | A7AHN12V01 |
| Деталь: | FERRITECORE |
| Парткод: | A7AHM90100 |
| Деталь: | CONNECTOR |
| Парткод: | A7AHM90000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH261802 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH261700 |
| Деталь: | Adjusting Plate |
| Парткод: | A7AH280700 |
| Деталь: | Pulling Spring |
| Парткод: | A7AH280500 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Idling Pulley |
| Парткод: | A7AH281300 |
| Деталь: | WASHER |
| Парткод: | A7AH281600 |
| Деталь: | Support Rubber |
| Парткод: | A4EU138000 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7AH281800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH280800 |
| Деталь: | Stepping motor |
| Парткод: | A161M10300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH261902 |
| Деталь: | Belt 1196L |
| Парткод: | A7AH280400 |
| Деталь: | Gear 120T |
| Парткод: | A7AH280900 |
| Деталь: | Protection Mat |
| Парткод: | A7AH262700 |
| Деталь: | FERRITECORE |
| Парткод: | A7AHM90200 |
| Деталь: | Insulating Part |
| Парткод: | A7AH263000 |
| Деталь: | Gear 24/35T |
| Парткод: | A7AH563700 |
| Деталь: | CLUTCH |
| Парткод: | A7AHM20500 |
| Деталь: | SHAFT |
| Парткод: | A7AH563800 |
| Деталь: | CLUTCH |
| Парткод: | A7AHM20400 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH579101 |
| Деталь: | DRIVE ROLLER |
| Парткод: | A7AH578100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A7AH578800 |
| Деталь: | ACTUATOR |
| Парткод: | A7AH578600 |
| Деталь: | Conveyance Guide |
| Парткод: | A7AH578200 |
| Деталь: | Paper feed Frame |
| Парткод: | A7AH565301 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH571100 |
| Деталь: | Photoreflector |
| Парткод: | A0EDM50100 |
| Деталь: | Conveyance Guide |
| Парткод: | A7AH565702 |
| Деталь: | Shaft /Paper feed |
| Парткод: | A7AH560500 |
| Деталь: | Paper feed Gear |
| Парткод: | A7AH562400 |
| Деталь: | CLUTCH |
| Парткод: | A02E561100 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | ROLLER |
| Парткод: | A5C1562200 |
| Деталь: | Conveyance Gear 28T |
| Парткод: | A7AH562600 |
| Деталь: | Idling Gear |
| Парткод: | A7AH562300 |
| Деталь: | Support Shaft |
| Парткод: | A7AH563400 |
| Деталь: | Protection Sheet |
| Парткод: | A7AH562900 |
| Деталь: | Conveyance Guide /4 |
| Парткод: | A7AH562100 |
| Деталь: | Harness /Paperfeed |
| Парткод: | A7AHN13100 |
| Деталь: | Protection Seal |
| Парткод: | A7AH569500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH579300 |
| Деталь: | Detecting Lever |
| Парткод: | A7AH561601 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A7AH562801 |
| Деталь: | Cover /Upper |
| Парткод: | A7AH160102 |
| Деталь: | TRAY |
| Парткод: | A7AH161001 |
| Деталь: | Label Toner 2 |
| Парткод: | A0ED940700 |
| Деталь: | Support Shaft |
| Парткод: | A161165602 |
| Деталь: | Cover Plate /Right front |
| Парткод: | A7AH162500 |
| Деталь: | BAND |
| Парткод: | A0ED162401 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475260302 |
| Деталь: | Open/close Cover /Right |
| Парткод: | A7AH162300 |
| Деталь: | Open/close Cover /Front |
| Парткод: | A7AH180200 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | Handle /Left |
| Парткод: | A7AH102200 |
| Деталь: | SEAL |
| Парткод: | A7AH134800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH102100 |
| Деталь: | Cover /Left |
| Парткод: | A7AH160700 |
| Деталь: | Cover /Left |
| Парткод: | A7AH160801 |
| Деталь: | HOLDER |
| Парткод: | A7AH160601 |
| Деталь: | Plate /D |
| Парткод: | A0Y5944800 |
| Деталь: | LABEL |
| Парткод: | A789942300 |
| Деталь: | OZONE FILTER |
| Парткод: | A7AHR72000 |
| Деталь: | BUSHING |
| Парткод: | A02E815200 |
| Деталь: | Idler Roller /A |
| Парткод: | A161825700 |
| Деталь: | ROLLER |
| Парткод: | A7AH816500 |
| Деталь: | GUIDE |
| Парткод: | A7AH816002 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Lock Shaft /A |
| Парткод: | A161711300 |
| Деталь: | Label M2 |
| Парткод: | A7AH944100 |
| Деталь: | Pulley 22T |
| Парткод: | A0ED811700 |
| Деталь: | Belt 296L |
| Парткод: | A7AH817300 |
| Деталь: | SHAFT |
| Парткод: | A7AH701000 |
| Деталь: | Lock Shaft /C |
| Парткод: | A161711500 |
| Деталь: | Label M1 |
| Парткод: | A7AH944000 |
| Деталь: | SPRING |
| Парткод: | A7AH701100 |
| Деталь: | ACTUATOR |
| Парткод: | A7AH813500 |
| Деталь: | HANDLE |
| Парткод: | A7AH700901 |
| Деталь: | Conveyance Spring /B |
| Парткод: | A161714600 |
| Деталь: | SPRING |
| Парткод: | A7AH812901 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313130051 |
| Деталь: | SEAL |
| Парткод: | A7AH819100 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED702400 |
| Деталь: | Guide Sheet |
| Парткод: | A7AH818100 |
| Деталь: | GUIDE |
| Парткод: | A7AH818000 |
| Деталь: | GUIDE |
| Парткод: | A7AH818200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH819000 |
| Деталь: | DUCT |
| Парткод: | A7AH819200 |
| Деталь: | GROUND SPRING |
| Парткод: | A7AH817101 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7AH816602 |
| Деталь: | Harness /Conveyance |
| Парткод: | A7AHN13000 |
| Деталь: | SEAL |
| Парткод: | A7AH819300 |
| Деталь: | COVER |
| Парткод: | A7AH819502 |
| Деталь: | SEAL |
| Парткод: | A7AH816800 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A7AH812800 |
| Деталь: | GROUND SPRING |
| Парткод: | A7AH816200 |
| Деталь: | GROUND PLATE |
| Парткод: | A7AH816100 |
| Деталь: | Support Shaft |
| Парткод: | A7AH816400 |
| Деталь: | GEAR |
| Парткод: | A7AH817200 |
| Деталь: | GUIDE |
| Парткод: | A7AH818300 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A7AHR70700 |
| Деталь: | Gear 23T |
| Парткод: | A7AH215400 |
| Деталь: | SHAFT |
| Парткод: | A7AH214800 |
| Деталь: | SHAFT |
| Парткод: | A7AH214701 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH215101 |
| Деталь: | Connecting Spring |
| Парткод: | A7AH704900 |
| Деталь: | HOLDER |
| Парткод: | A7AH704201 |
| Деталь: | CONTACT |
| Парткод: | A7AH707201 |
| Деталь: | CONTACT |
| Парткод: | A7AH707101 |
| Деталь: | GUIDE |
| Парткод: | A7AH134401 |
| Деталь: | Positioning Holder /Front |
| Парткод: | A7AH704601 |
| Деталь: | Positioning Holder /Rear |
| Парткод: | A7AH704701 |
| Деталь: | Gear 14/37T |
| Парткод: | A7AH213500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH216700 |
| Деталь: | Drive Holder |
| Парткод: | A7AH213902 |
| Деталь: | GEAR 28T |
| Парткод: | A7AH212800 |
| Деталь: | GEAR 26T |
| Парткод: | A7AH213000 |
| Деталь: | GEAR 37T |
| Парткод: | A7AH212600 |
| Деталь: | Gear 23/31T |
| Парткод: | A7AH216500 |
| Деталь: | Gear 27/35T |
| Парткод: | A7AH212300 |
| Деталь: | Gear 22/29T |
| Парткод: | A7AH212200 |
| Деталь: | Gear 30/35T |
| Парткод: | A7AH212100 |
| Деталь: | GEAR 26T |
| Парткод: | A7AH211700 |
| Деталь: | GEAR 26T |
| Парткод: | A7AH214300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH212000 |
| Деталь: | Gear 65T |
| Парткод: | A161240600 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038541202 |
| Деталь: | JOINT |
| Парткод: | A161240700 |
| Деталь: | Gear 15/91T |
| Парткод: | A7AH217100 |
| Деталь: | Gear 29/62T |
| Парткод: | A161240400 |
| Деталь: | Drive Holder |
| Парткод: | A7AH217001 |
| Деталь: | Toner bottle Drive Assy |
| Парткод: | A7AHR70200 |
| Деталь: | Stepping motor |
| Парткод: | A7AHM10400 |
| Деталь: | brushless Motor /20 |
| Парткод: | A61DM10200 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | Guide /Lower |
| Парткод: | A7AH813001 |
| Деталь: | Spring /D |
| Парткод: | A161712800 |
| Деталь: | ACTUATOR |
| Парткод: | A161813200 |
| Деталь: | Pressing Spring /A |
| Парткод: | A161813600 |
| Деталь: | Holding Part |
| Парткод: | A0ED815100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH894100 |
| Деталь: | Contact /C |
| Парткод: | A161819400 |
| Деталь: | Bushing /B |
| Парткод: | A161814500 |
| Деталь: | BUSHING |
| Парткод: | A02E815200 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161813400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH813300 |
| Деталь: | GUIDE PLATE |
| Парткод: | A7AH893102 |
| Деталь: | GEAR 18T |
| Парткод: | A7AH891100 |
| Деталь: | COLLAR |
| Парткод: | A7AH893400 |
| Деталь: | Harness /Conveyance |
| Парткод: | A7AHN11802 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7AH893301 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | A7AH893000 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161813100 |
| Деталь: | ACTUATOR |
| Парткод: | A7AH894000 |
| Деталь: | Bushing /C |
| Парткод: | A161819500 |
| Деталь: | SEAL |
| Парткод: | A7AH819400 |
Коды ошибок
C0002
C0106
C0107
C0108
C0109
C0202
C0204
C0206
C0208
C0210
C0211
C0214
C1004
C1081
C1102
C1103
C1105
C1106
C1109
C1112
C1113
C1114
C1115
C1132
C1140
C1141
C1144
C1145
C1156
C1182
C1184
C1195
C1196
C1197
C11A1
C11A2
C11E1
C1402
C2253
C2254
C2350
C2414
C2557
C2558
C255C
C2564
C2650
C2A14
C3421
C3721
C3722
C3731
C3821
C3822
C3921
C3922
C40A1
C40A2
C40A3
C40A4
C4101
C4501
C5102
C5103
C5354
C5356
C5359
C5370
C5372
C5501
C5601
C5605
C5606
C6102
C6103
C6704
C6751
C6752
C6756
C6F01
C8101
C8107
C8401
C9401
C9402
CA051
CA052
CA053
CC140
CC151, CC152
CC155
CC156
CC15B
CC163
CC164
CC170 ... CC186
CC190
CC191
CC211
CC212
CC213
CC214
CC216
CD002
CD004, CD00F, CD020
CD010
CD011
CD012
CD030
CD041 ... CD046
CD047 ... CD04B
CD050
CD110
CD201, CD202, CD203
CD211, CD212
CD241, CD242
CD261
CD262
CD271
CD272
CD300 ... CD370
CD390
CD3A0
CD401 ... CD413
CD601, CD602, CD603
CD701, CD702, CD703
CD704
CD705, CD706
CDF50, CDF70, CDFA0
CE001 ... CE007
CE002
CE101
CE201
CE301 ... CE305
CED01
CEEE1, CEEE3
CEEE2
CF0xx
CF1xx
CF2xx
CF3xx
CF4xx
CF5xx
CF6xx
CF7xx
CF8xx
CF9xx
CFAxx
CFB00 ... CFFBD
Описание
| Error code: | C0002 |
| Description: | Paper feed communication error. When the paper feed/transport drive board (PFTDB) is receiving data, a communication error is detected. |
| Causes: | • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Correct the harness connection between MFPB CN7E-PFTDB CN4 if faulty. 3. Rewrite the firmware. 4. PFTDB F3 conduction check 5. Replace PFTDB. 6. MFPB F2E conduction check 7. Replace MFPB. |
| Error code: | C0106 |
| Description: | Tray 3/LCT paper feed motor turning at abnormal timing • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | <When PC-110 or PC-210 is installed> • Tray 3 paper feed motor (M111) • PC control board (PCCB) <When PC-410 is installed> • Paper feed motor (M131) • PC control board (PCCB) |
| Remedy: | When PC-110 or PC-210 is installed: 1 Check the connector between M111-PCCB CN5 for proper connection and correct as necessary. 2 Check the connector of M111 for proper drive coupling and correct as necessary. 3 M111 operation check PCCB CN5-5 (CW/CCW) PC-110/PC-210 4-C. 4 Replace M111. 5 Replace PCCB. When PC-410 is installed: 1 Check the connector between M131-PCCB CN5 for proper connection and correct as necessary. 2 Check the connector of M131 for proper drive coupling and correct as necessary. 3 M131 operation check PCCB CN5-5 (CW/CCW) PC-410 5-J 4 Replace M131. 5 Replace PCCB. |
| Error code: | C0107 |
| Description: | Tray 3/LCT vertical transport motor turning at abnormal timing • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | <When PC-110 or PC-210 is installed> • Tray 3 vertical transport motor (M112) • PC control board (PCCB) <When PC-410 is installed> • Vertical transport motor (M132) • PC control board (PCCB) |
| Remedy: | When PC-110 or PC-210 is installed: 1 Check the connector between M112-PCCB CN5 for proper connection and correct as necessary. 2 Check the connector of M112 for proper drive coupling and correct as necessary. 3 M112 operation check PCCB CN5-13 (CW/CCW) PC-110/PC-210 3 to 4-C. 4 Replace M112. 5 Replace PCCB. When PC-410 is installed: 1 Check the connector between M132-PCCB CN5 for proper connection and correct as necessary. 2 Check the connector of M132 for proper drive coupling and correct as necessary. 3 M132 operation check PCCB CN5-13 (CW/CCW) PC-410 4-J. 4 Replace M132. 5 Replace PCCB. |
| Error code: | C0108 |
| Description: | Tray 4 paper feed motor turning at abnormal timing <When PC-210 is installed> • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Tray 4 paper feed motor (M121) • PC control board (PCCB) |
| Remedy: | 1 Check the connector between M121-PCCB CN9 for proper connection and correct as necessary. 2 Check the connector of M121 for proper drive coupling and correct as necessary. 3 M121 operation check PCCB CN9-5 (CW/CCW) PC-210 6-K. 4 Replace M121. 5 Replace PCCB |
| Error code: | C0109 |
| Description: | Tray 4 vertical transport motor turning at abnormal timing <When PC-210 is installed> • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Tray 4 vertical transport motor (M122) • PC control board (PCCB) |
| Remedy: | 1 Check the connector between M122-PCCB CN9 for proper connection and correct as necessary. 2 Check the connector of M122 for proper drive coupling and correct as necessary. 3 M122 operation check PCCB CN9-13 (CW/CCW) PC-210 6-K. 4 Replace M122. 5 Replace PCCB. |
| Error code: | C0202 |
| Description: | Magenta PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 1 upper limit sensor (PS6) • Tray 1 lift-up motor (M6) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0204 |
| Description: | Yellow PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 2 upper limit sensor (PS14) • Tray 2 lift-up motor (M8) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0206 |
| Description: | Black PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 3 upper limit sensor (PS22) • Tray 3 lift-up motor (M23) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0208 |
| Description: | Tray 5 feeder up/down abnormality |
| Causes: | • Tray 4 upper limit sensor (PS27) • Tray 4 lift-up motor (M24) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0211 |
| Description: | Tray 1 feeder up/down abnormality • The paper feed tray 1 lift-up position sensor is not unblocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The paper feed tray 1 lift-up position sensor is not blocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started. |
| Causes: | • Bypass lift-up motor (M26) • Bypass upper limit sensor (PS35) • Bypass lower limit sensor (PS36) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check the connector of M1 for proper drive coupling and correct as necessary. 3 PS17 I/O check PRCB CN6PRCB-7 (ON) D-2. 4 SL1 operation check PRCB CN6PRCB-4 (ON) D-1. 5 M1 operation check PRCB CN34PRCB-10 (REM) PRCB CN34PRCB-13 (LOCK) D-22. 6 Change SL1. 7 Change M1. 8 Change PRCB. |
| Error code: | C0214 |
| Description: | LCT shifting failure |
| Causes: | • Shifter motor (M133) • Shifter stop / lower limit position sensor (PS138) • Shifter home sensor (PS139) • PC control board (PCCB) |
| Error code: | C1004 |
| Description: | FNS communication error |
| Causes: | FS control board (FSCB) |
| Error code: | C1081 |
| Description: | SD communication error <When FS-534+SD-511 is installed> When a communication error is detected between the FS control board (FSCB) and the SD control board (SDDB). |
| Causes: | • SD drive board (SDDB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace SDDB. 4 Replace FSCB. |
| Error code: | C1102 |
| Description: | Main tray up/down motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • While the exit tray is being lifted, the main tray upper position sensor (PS26/PS27) is not turned ON (blocked) and the main tray upper position detect switch (SW2) is not turned ON, even after the main tray up/down motor (M11) turns by the set number of times. • While the exit tray is being lowered, the main tray full detection sensor (PS29) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M11) is turned ON. <When FS-537 or FS-537SD is installed> • The main tray lift up detection sensor (PS16/PS17) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/ down motor (M6) is turned ON. • The main tray full detection sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M6) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Main tray up/down motor (M11) • Main tray upper position sensor/R (PS26) • Main tray upper position sensor/F (PS27) • Main tray full detection sensor (PS29) • Main tray upper position detect switch (SW2) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Main tray up/down motor (M6) • Main tray lift up detection sensor/F (PS16) • Main tray lift up detection sensor/R (PS17) • Main tray full detection sensor (PS12) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M11-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M11 for proper drive coupling, and correct as necessary. 3. Check the connector between PS26-relay CN1-FSCB J14 for proper connection and correct as necessary. 4. Check the connector between PS27-relay CN1-FSCB J14 for proper connection and correct as necessary. 5. Check the connector between PS29-relay CN2-FSCB J14 for proper connection and correct as necessary. 6. Check the connector between SW2-FSCB J10 for proper connection and correct as necessary. 7. PS26 I/O check, sensor check • Control signal: FSCB J14<A>-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-C 8. PS27 I/O check, sensor check • Control signal: FSCB J14<B>-6 (ON) • Location of electrical component: FS-536/FS-536SD 3-C 9. PS29 I/O check, sensor check • Control signal: FSCB J14<A>-8 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 10. SW2 operation check • Control signal: FSCB J10-1 to 2 • Location of electrical component: FS-536/FS-536SD 15-K 11. M11 operation check • Control signal: FSCB J9<A>-9 to 10 • Location of electrical component: FS-536/FS-536SD 12-C 12. Replace M11. 13. FSCB F2 conduction check 14. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M6-FSCB J23 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS16-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 4. Check the connector between PS17-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 5. Check the connector between PS12-relay CN9-FSCB J19 for proper connection and correct as necessary. 6. PS16 I/O check, sensor check • Control signal: FSCB J20<B>-4 (ON) • Location of electrical component: FS-537/FS-537SD 11 to 12-D 7. PS17 I/O check, sensor check • Control signal: FSCB J20<B>-7 (ON) • Location of electrical component: FS-537/FS-537SD 12-D 8. PS12 I/O check, sensor check • Control signal: FSCB J19-7 (ON) • Location of electrical component: FS-537/FS-537SD 10-D 9. M6 operation check • Control signal: FSCB J23-1 to 11 • Location of electrical component: FS-537/FS-537SD 13-D 10. Replace M6. 11. FSCB F3 conduction check 12. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1103 |
| Description: | Alignment motor/Front’s drive malfunction. <When FS-536 or FS-536SD is installed> • The alignment plate/F home sensor (PS12) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M7) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. <When FS-537 or FS-537SD is installed> • The alignment plate/F home sensor (PS9) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS9) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M14) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. |
| Causes: | <When FS-536 or FS-536SD is installed> • Alignment motor/Front (M7) • Alignment plate/F home sensor (PS12) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Alignment motor/Front (M14) • Alignment plate/F home sensor (PS9) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M7-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS12-FSCB J4 for proper connection and correct as necessary. 4. PS12 I/O check, sensor check • Control signal: FSCB J4<B>-4 (ON) • Location of electrical component: FS-536/FS-536SD 15-C 5. M7 operation check • Control signal: FSCB J4<A>-5 to 8 • Location of electrical component: FS-536/FS-536SD 14-C 6. Replace M7. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M14-relay CN5-FSCB J18 for proper connection and correct as necessary. 2. Check the connector of M14 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-relay CN5-FSCB J18 for proper connection and correct as necessary. 4. PS9 I/O check, sensor check • Control signal: FSCB J18-10 (ON) • Location of electrical component: FS-537/FS-537SD 6-D 5. M14 operation check • Control signal: FSCB J18-1 to 4 • Location of electrical component: FS-537/FS-537SD 6-D 6. Replace M14. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1105 |
| Description: | Bundle eject motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • The gripper home position sensor (PS18) is not turned ON (unblocked) even after the set period of time has elapsed after the gripper position detection sensor (PS19) turns OFF (block). • The gripper position detection sensor (PS19) is not turned OFF (blocked) even after the set period of time has elapsed after PS19 turns ON (unblock). • The gripper position detection sensor (PS19) is not turned ON (unblocked) even after the set period of time has elapsed after the gripper home position sensor (PS18) turns OFF (block). • The gripper home position sensor (PS18) is not turned OFF (blocked) even after the set period of time has elapsed after the bundle eject motor (M10) is energized. • The gripper home position sensor (PS18) and the gripper position detection sensor (PS19) is turned ON (unblocked) at the same time. <When FS-537 or FS-537SD is installed> The gripper home position sensor (PS3) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed after the bundle eject motor (M1) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Bundle eject motor (M10) • Gripper home position sensor (PS18) • Gripper position detection sensor (PS19) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Bundle eject motor (M1) • Gripper home position sensor (PS3) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M10-relay CN7<A>-FSCB J13 for proper connection and correct as necessary. 2. Check the connector of M10 for proper drive coupling, and correct as necessary. 3. Check the connector between PS18-relay CN7<A>-FSCB J13 for proper connection and correct as necessary. 4. Check the connector between PS19-relay CN8<B>-FSCB J12 for proper connection and correct as necessary. 5. PS18 I/O check, sensor check • Control signal: FSCB J13-13 (ON) • Location of electrical component: FS-536/FS-536SD 8-C 6. PS19 I/O check, sensor check • Control signal: FSCB J12-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 7. M10 operation check • Control signal: FSCB J13-1 to 2 • Location of electrical component: FS-536/FS-536SD 9-C 8. Replace M10. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M1-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS3-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 4. PS3 I/O check, sensor check • Control signal: FSCB J22<A>-13 (ON) • Location of electrical component: FS-537/FS-537SD 2-D 5. M1 operation check • Control signal: FSCB J22<A>-1 to 2 • Location of electrical component: FS-537/FS-537SD 1-D 6. Replace M1. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1106 |
| Description: | Stapler movement motor’s malfunction. <When FS-536 or FS-536SD is installed> • The stapler home position sensor (rear) (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the side stapler movement motor (M13) turned ON. • The stapler does not reach the specified position within the set period of time. <When FS-537 or FS-537SD is installed> • The stapler home position sensor (PS18/PS19) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler movement motor (M19) turned ON. • The stapler does not reach the specified position within the set period of time. |
| Causes: | <When FS-536 or FS-536SD is installed> • Side stapler movement motor (M13) • Stapler home position sensor (rear) (PS23) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler movement motor (M19) • Stapler home position sensor (corner) (PS18) • Stapler home position sensor (rear) (PS19) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M13-relay CN3-FSCB J11 for proper connection, and correct as necessary. 2. Check the connector of M13 for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 5. M13 operation check • Control signal: FSCB J11<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 4-C 6. Replace M13. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M19-FSCB J17 for proper connection and correct as necessary. 2. Check the connector of M19 for proper drive coupling and correct as necessary. 3. Check the connector between PS18-FSCB J16 for proper connection and correct as necessary. 4. Check the connector between PS19-FSCB J16 for proper connection and correct as necessary. 5. PS18 I/O check, sensor check • Control signal: FSCB J16-9 (ON) • Location of electrical component: FS-537/FS-537SD15-D 6. PS19 I/O check, sensor check • Control signal: FSCB J16-6 (ON) • Location of electrical component: FS-537/FS-537SD 15-D 7. M19 operation check • Control signal: FSCB J17-10 to 13 • Location of electrical component: FS-537/FS-537SD 14-D 8. Replace M19. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1109 |
| Description: | Stapler motor’s malfunction. <When FS-536 or FS-536SD is installed> • The stapler home position sensor (rear) (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler motor (M14) turned ON. • The stapler position sensor (center) (PS24) is turned ON (blocked), when the stapler motor (M14) is running. <When FS-537 or FS-537SD is installed> • The stapler home position sensor (PS18/PS19) is not turned (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler movement motor (M5) turned ON. • The stapler position sensor (center) (PS20) is turned ON (blocked), when the stapler motor (M5) is running. |
| Causes: | <When FS-536 or FS-536SD is installed> • Stapler unit • Stapler home position sensor (rear) (PS23) • Stapler position sensor (center) (PS24) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler unit • Stapler home position sensor (corner) (PS18) • Stapler home position sensor (rear) (PS19) • Stapler position sensor (center) (PS20) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between the stapler unit-relay CN4-FSCB J11 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. Check the connector between PS24-relay CN3-FSCB J11 for proper connection and correct as necessary. 5. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 6. PS24 I/O check, sensor check • Control signal: FSCB J11<B>-6 • Location of electrical component: FS-536/FS-536SD 5-C 7. Replace the stapler unit. 8. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between the stapler unit-FSCB J17 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS18-FSCB J16 for proper connection and correct as necessary. 4. Check the connector between PS19-FSCB J16 for proper connection and correct as necessary. 5. Check the connector between PS20-FSCB J16 for proper connection and correct as necessary. 6. PS18 I/O check, sensor check • Control signal: FSCB J16-9 • Location of electrical component: FS-537/FS-537SD 15-D 7. PS19 I/O check, sensor check • Control signal: FSCB J16-6 • Location of electrical component: FS-537/FS-537SD 15-D 8. PS20 I/O check, sensor check • Control signal: FSCB J16-3 • Location of electrical component: FS-537/FS-537SD 15-D 9. Replace the stapler unit. 10. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1112 |
| Description: | Stapler motor`s drive malfunction. <When FS-536SD or FS-537SD is installed> • The stapler home sensor is not turned ON even after the set period of time has elapsed while the stapler motor is energized. • The stapler home sensor is not turned OFF even after the set period of time has elapsed after the stapler home sensor is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Staple unit • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between the staple unit-SDCB J4 for proper connection and correct as necessary. 2. Check the connector of the staple unit for proper drive coupling and correct as necessary. 3. Replace the staple unit. (FS-536SD/FS-537SD) 4. Replace SDCB. (FS-536SD/FS-537SD) 5. Replace FSCB. (FS-536SD/FS-537SD) |
| Error code: | C1113 |
| Description: | Stopper drive motor`s malfunction. <When FS-536SD or FS-537SD is installed> The stopper home sensor (PS6) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stopper drive motor (M4) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Stopper drive motor (M4) • Stopper home sensor (PS6) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M4-SDCB J10 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-SDCB J10 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: SDCB J10-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 2-P 5. M4 operation check • Control signal: SDCB J10-6 to 9 • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 1-P 6. Replace M4. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1114 |
| Description: | Alignment motor’s malfunction. <When FS-536SD or FS-537SD is installed> The alignment home sensor (PS4) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the alignment motor (M3) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Alignment motor (M3) • Alignment home sensor (PS4) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M3-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS4-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS4 I/O check, sensor check • Control signal: SDCB J7-6 (ON) • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 5. M3 operation check • Control signal: SDCB J7-7 to 10 • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 6. Replace M3. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1115 |
| Description: | Center fold knife motor`s malfunction. <When FS-536SD or FS-537SD is installed> The center fold knife home sensor (PS8) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Center fold knife motor (M9) • Center fold knife home sensor (PS8) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M9-SDCB J11 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS8-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS8 I/O check, sensor check • Control signal: SDCB J7-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-P, FS-537/FS-537SD 6-P 5. M9 operation check • Control signal: SDCB J11-11 to 20 • Location of electrical component: FS-536/FS-536SD 2-L, FS-537/FS-537SD 1-K 6. Replace M9. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1132 |
| Description: | Punch drive motor’s drive malfunction. <When FS-536+PK-520 or FS-536SD+PK-520 is installed> The punch home sensor (PS1) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the punch drive motor (M1) is energized. <When FS-537+PK-523 or FS-537SD+PK-523 is installed> The PK punch home sensor/2(PS301) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the punch drive motor (M301) is energized. |
| Causes: | <When FS-536+PK-520 or FS-536SD+PK-520 is installed> • Punch drive motor (M1) • Punch home sensor (PS1) • FS control board (FSCB) <When FS-537+PK-523 or FS-537SD+PK-523 is installed> • Punch drive motor (M301) • PK punch home sensor/2(PS301) • Punch control board (PKCB) • FS control board (FSCB) |
| Remedy: | (a) When FS-536+PK-520 or FS-536SD+PK-520 is installed 1. Check the connector between M1-relay CN351-FSCB J7 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS1-FSCB J7 for proper connection and correct as necessary. 4. PS1 I/O check, sensor check • Control signal: FSCB J7-5 (ON) • Location of electrical component: FS-536/FS-536SD 13-K 5. M1 operation check • Control signal: FSCB J7-7 to 8 • Location of electrical component: FS-536/FS-536SD 13-K 6. Replace M1. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537+PK-523 or FS-537SD+PK-523 is installed 1. Check the connector between M301-relay CN351-PKCB CN35 for proper connection and correct as necessary. 2. Check the connector of M301 for proper drive coupling and correct as necessary. 3. Check the connector between PS301-PKCB CN36 for proper connection and correct as necessary. 4. PS301 I/O check, sensor check • Control signal: PKCB CN36-5 (ON) • Location of electrical component: PK-523 3-C 5. M301 operation check • Control signal: PKCB CN35-1 to 3 • Location of electrical component: PK-523 2-C 6. Replace M301. 7. Replace PKCB. 8. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.4 PK-523) |
| Error code: | C1140 |
| Description: | PF lift motor error Object: Side feeder |
| Causes: | 1. The PF lift upper limit sensor does not turn on when passing 30s after cassette 5 is inserted. 2. The lock-up signal is detected for 200ms continuously during the PF lift motor operation. 3. The PF lift upper limit sensor does not turn on when passing 2s after the upper limit control when printing starts. |
| Remedy: | 1 Checking the bottom plate The bottom plate does not operate properly. Repair or replace the bottom plate when it does not move vertically. 2 Checking the drive gear The drive gear to lift up the bottom plate does not rotate properly. Check if the drive gears to lift up the bottom plate rotate smoothly or have no excessive load. And apply the grease to the frictional parts and fix the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor - PF main PWB Wiring diagram 4 Checking the PF lift motor The PF lift motor is faulty. Replace the PF lift motor. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift upper limit sensor - PF main PWB Wiring diagram 6 Checking the PF lift upper limit sensor The PF lift upper limit sensor is not properly attached or faulty. Reattach the PF lift upper limit sensor. Then, replace it if it is not fixed. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1141 |
| Description: | FNS paddle motor’s malfunction. <When FS-536 or FS-536SD is installed> The upper paddle home position detection sensor (PS14) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M5) is turning. <When FS-537 or FS-537SD is installed> The paddle home sensor (PS25) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M9) is turning. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS paddle motor (M5) • Upper paddle home position detection sensor (PS14) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • FNS paddle motor (M9) • Paddle home sensor (PS25) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M5-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS14-FSCB J4 for proper connection and correct as necessary. 4. PS14 I/O check, sensor check • Control signal: FSCB J4<B>-7 (ON) • Location of electrical component: FS-536/FS-536SD 15-C 5. M5 operation check • Control signal: FSCB J4<A>-9 to 12 • Location of electrical component: FS-536/FS-536SD 14-C 6. Replace M5. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M9-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS25-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 4. PS25 I/O check, sensor check • Control signal: FSCB J14<B>-10 (ON) • Location of electrical component: FS-537/FS-537SD 16-K to L 5. M9 operation check • Control signal: FSCB J14<B>-4 to 7 • Location of electrical component: FS-537/FS-537SD 17- K to L 6. Replace M9. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1144 |
| Description: | Pre-eject drive motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • The pre-eject home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the preeject drive motor (M9) is turned ON. • The pre-eject away sensor (PS22) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the preeject drive motor (M9) is turned ON. <When FS-537 or FS-537SD is installed> The trail edge stopper home sensor (PS31) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the pre-eject drive motor (M2) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Pre-eject drive motor (M9) • Pre-eject home sensor (PS21) • Pre-eject away sensor (PS22) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Pre-eject drive motor (M2) • Trail edge stopper home sensor (PS31) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M9-relay CN7<A>-FSCB J13 for proper connection, and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 4. Check the connector between PS22-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 5. PS21 I/O check, sensor check • Control signal: FSCB J12-6 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 6. PS22 I/O check, sensor check • Control signal: FSCB J12-9 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 7. M9 operation check • Control signal: FSCB J13-3 to 4 • Location of electrical component: FS-536/FS-536SD 9-C 8. Replace M9. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M2-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS31-relay CN2-relay CN1<B>-FSCB J22 for proper connection and correct as necessary. 4. PS31 I/O check, sensor check • Control signal: FSCB J22<B>-13 • Location of electrical component: FS-537/FS-537SD 3-D 5. M2 operation check • Control signal: FSCB J22<A>-3 to 4 • Location of electrical component: FS-537/FS-537SD 1-D 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1145 |
| Description: | Trailing edge stopper motor malfunction. <When FS-536 or FS-536SD is installed> The trailing edge stopper home position detection sensor (PS20) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the trailing edge stopper motor (M6) is turned ON. <When FS-537 or FS-537SD is installed> The trailing edge stopper home position detection sensor/F (PS10) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the trailing edge stopper motor/F (M12) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Trailing edge stopper motor (M6) • Trailing edge stopper home position detection sensor (PS20) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Trail edge stopper motor/F (M12) • Trail edge stopper sensor/F (PS10) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M6-FSCB J5 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS20-relay CN19-FSCB J5 for proper connection and correct as necessary. 4. PS20 I/O check, sensor check • Control signal: FSCB J5-9 (ON) • Location of electrical component: FS-536/FS-536SD 15-K 5. M6 operation check • Control signal: FSCB J5-13 to 16 • Location of electrical component: FS-536/FS-536SD 15-K 6. Replace M6. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M12-relay CN5-FSCB J18 for proper connection and correct as necessary. 2. Check the connector of M12 for proper drive coupling and correct as necessary. 3. Check the connector between PS10-relay CN5-FSCB J18 for proper connection and correct as necessary. 4. PS10 I/O check, sensor check • Control signal: FSCB J18-13 (ON) • Location of electrical component: FS-537/FS-537SD 6 to 7-D 5. M12 operation check • Control signal: FSCB J18-14 to 17 • Location of electrical component: FS-537/FS-537SD 7-D 6. Replace M12. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1156 |
| Description: | SD paddle motor malfunction. <When FS-536SD or FS-537SD is installed> The paddle home sensor (PS5) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the SD paddle motor (M7) is turning. |
| Causes: | <When FS-536SD or FS-537SD is installed> • SD paddle motor (M7) • Paddle home sensor (PS5) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M7-SDCB J8 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS5-SDCB J8 for proper connection and correct as necessary. 4. PS5 I/O check, sensor check • Control signal: SDCB J8-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 5. M7 operation check • Control signal: SDCB J8-4 to 7 • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 6. Replace M7. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1182 |
| Description: | Unsupported option trouble |
| Causes: | When JS-504 is installed: Shift motor (M2) Shift home sensor (PS6) JS control board (JSCB). When FS-527 is installed: Tray2 shift motor (M16) Tray2 shift home sensor (PS25) FS control board (FSCB) |
| Error code: | C1184 |
| Description: | Paper discharge control motor malfunction. <When FS-536 or FS-536SD is installed> The paper delivery control sensor (PS28) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed while the paper receiving control motor (M12) is energized. <When FS-537 or FS-537SD is installed> The paper delivery control sensor (PS11) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed while the paper receiving control motor (M15) is energized. |
| Causes: | <When FS-536 or FS-536SD is installed> • Paper receiving control motor (M12) • Paper delivery control sensor (PS28) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Paper receiving control motor (M15) • Paper delivery control sensor (PS11) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M12-relay CN1-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M12 for proper drive coupling and correct as necessary. 3. Check the connector between PS28-relay CN1-FSCB J14 for proper connection and correct as necessary. 4. PS28 I/O check, sensor check • Control signal: FSCB J14<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 2 to 3-C 5. M12 operation check • Control signal: FSCB J14<A>-9 to 12 • Location of electrical component: FS-536/FS-536SD 2-C 6. Replace M12. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M15-FSCB J19 for proper connection and correct as necessary. 2. Check the connector of M15 for proper drive coupling and correct as necessary. 3. Check the connector between PS11-relay CN10<A>-FSCB J20 for proper connection and correct as necessary. 4. PS11 I/O check, sensor check • Control signal: FSCB J20<A>-3 (ON) • Location of electrical component: FS-537/FS-537SD 10-D 5. M15 operation check • Control signal: FSCB J19-1 to 4 • Location of electrical component: FS-537/FS-537SD 10-D 6. Replace M15. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1195 |
| Description: | Paper discharge control motor malfunction. <When FS-536SD or FS-537SD is installed> The curl cover detection sensor (PS2) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the paper discharge control motor (M2) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Paper discharge control motor (M2) • Curl cover detection sensor (PS2) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M2-relay CN22 (FS-536SD), CN25 (FS-537SD)-relay CN21 (FS-536SD), CN26 (FS-537SD)-SDCB J5 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-relay CN22 (FS-536SD), CN25 (FS-537SD)-relay CN21 (FS-536SD), CN26 (FS-537SD)-SDCB J5 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: SDCB J5-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-L, FS-537/FS-537SD 3-K 5. M2 operation check • Control signal: SDCB J5-4 to 7 • Location of electrical component: FS-536/FS-536SD 4-L, FS-537/FS-537SD 3-K 6. Replace M2. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1196 |
| Description: | Center fold guide motor’s drive malfunction. <When FS-536SD or FS-537SD is installed> The guide home sensor (PS7) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the center fold roller motor (M6) is turned ON. |
| Causes: | <When FS-536SD is installed> <When FS-537SD is installed> • Center fold guide motor (M6) • Guide home sensor (PS7) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M6-SDCB J9 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS7-SDCB J9 for proper connection and correct as necessary. 4. PS7 I/O check, sensor check • Control signal: SDCB J9-6 (ON) • Location of electrical component: FS-536/FS-536SD 5-P, FS-537/FS-537SD 4-P 5. M6 operation check • Control signal: SDCB J9-7 to 10 • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 4-P 6. Replace M6. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1197 |
| Description: | Tri-folding guide motor’s drive malfunction. <When FS-536SD or FS-537SD is installed> The tri-folding gate home sensor (PS11) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the tri-folding guide motor (M8) is energized. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Tri-folding guide motor (M8) • Tri-folding gate home sensor (PS11) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M8-SDCB J8 for proper connection and correct as necessary. 2. Check the connector of M8 for proper drive coupling and correct as necessary. 3. Check the connector between PS11-SDCB J8 for proper connection and correct as necessary. 4. PS11 I/O check, sensor check • Control signal: SDCB J8-10 (ON) • Location of electrical component: FS-536/FS-536SD 3-P, FS-537/FS-537SD 3-P 5. M8 operation check • Control signal: SDCB J8-11 to 14 • Location of electrical component: FS-536/FS-536SD 3-P, FS-537/FS-537SD 2-P 6. Replace M8. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C11A1 |
| Description: | Finishing option exit roller pressure/retraction failure |
| Causes: | Exit roller retraction motor (M9) Exit roller pressure sensor (PS12) FS control board (FSCB) |
| Error code: | C11A2 |
| Description: | Saddle exit roller pressure/retraction failure |
| Causes: | <When FS-536 or FS-536SD is installed> • Receiving roller retraction motor (M4) • Receiving roller retraction sensor (PS11) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Receiving roller retraction motor (M10) • Receiving roller retraction sensor (PS22) • FS control board (FSCB) |
| Error code: | C11E1 |
| Description: | Paper exit switching drive malfunction. <When FS-536 or FS-536SD is installed> The exchange folded paper output sensor (PS30) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the FNS entry transport motor (M2) is turned ON. <When FS-537 or FS-537SD is installed> The route change gate home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the route change gate motor (M4) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS entry transport motor (M2) • Exchange folded paper output sensor (PS30) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Route change gate motor (M4) • Route change gate home sensor (PS21) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M2-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS30-FSCB J4 for proper connection and correct as necessary. 4. PS30 I/O check, sensor check • Control signal: FSCB J4<A>-15 (ON) • Location of electrical component: FS-536/FS-536SD 14-C 5. M2 operation check • Control signal: FSCB J9<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 12-C 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M4-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-FSCB J12 for proper connection and correct as necessary. 4. PS21 I/O check, sensor check • Control signal: FSCB J12<B>-12 (ON) • Location of electrical component: FS-537/FS-537SD 18-D 5. M4 operation check • Control signal: FSCB J21<B>-8 to 9 • Location of electrical component: FS-537/FS-537SD 18-D 6. Replace M4. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1402 |
| Description: | IR illegal interrupt vector occurred |
| Causes: | FS control board (FSCB) |
| Remedy: | 1. Reset the malfunction. 2. If the same malfunction persists, change the Image Processing Board. |
| Error code: | C2253 |
| Description: | Color PC motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/YMC (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2254 |
| Description: | Color PC motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/YMC motor (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2350 |
| Description: | Toner suction fan failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Toner suction fan (FM7) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM7-relay CN326-MFPB CN24E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM7 operation check • Control signal: MFPB CN24E-7 (DRIVE), MFPB CN24E-9 (LOCK) • Location of electrical component: 1-K 4. Replace FM7. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C2414 |
| Description: | Developing unit new article release. The status with the new unit is not cleared after the new developing unit is set. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Replace the developing unit. 3. Replace MFPB. |
| Error code: | C2557 |
| Description: | Abnormally low toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Developing unit • Toner cartridge • Toner empty sensor/K (PZS/K) • Toner supply motor/K (M12) • Toner cartridge motor/CK (M14) • MFP board (MFPB) |
| Remedy: | 1 M3 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 D-23. 2 Reinstall imaging unit. 3 Reinstall toner cartridge. 4 Change imaging unit /K. 5 Change PRCB. |
| Error code: | C2558 |
| Description: | Abnormally high toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Developing unit • Toner cartridge • Sub hopper unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit /K. 4 Change PRCB. |
| Error code: | C255C |
| Description: | Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit /K. 2 Change imaging unit /K. 3 Change PRCB. |
| Error code: | C2564 |
| Description: | Black TCR sensor failure. • The TCR sensor input is 0. • This detection is used for detecting disconnection of TCR sensor connector. |
| Causes: | • Developing unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Check the connector between the developing unit-relay CN214-PHRYB CN6 for proper connection and correct as necessary. 3. Replace the developing unit. 4. PHRYB PS1 conduction check. 5. Replace PHRYB. 6. Replace MFPB |
| Error code: | C2650 |
| Description: | PF feed motor error (Side Multi Feeder) Object: Side multi feeder |
| Causes: | The ready signal is not at the L level (stable rotation) for passing 2s since the PF feed motor drive is started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected. The drive parts are faulty. Execute U247 [SMT] > [Motor On] to check the paper feeding operation. If the PF feed motor does not properly operate, reconnect the connector. Check if the PF feed roller and the drive gears rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. Executing U247 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF main PWB • PF main PWB - Engine PWB (Cable from the side multi feeder) Wiring diagram 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF drive unit (Side multi feeder) 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 5 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2A14 |
| Description: | Drum unit new release failure. The status with the new unit is not cleared after the new drum unit is set. |
| Causes: | • Drum unit • MFP board (MFPB) |
| Remedy: | 1. Clean the connection between the drum unit and the developing unit if dirty. 2. Reinstall the drum unit. 3. Check the harness for proper connection and correct as necessary. 4. Replace the drum unit. 5. Replace MFPB. |
| Error code: | C3421 |
| Description: | Fusing heaters trouble (heating side) • The temperature detected by the heating roller thermistor/C does not reach a predetermined level after the lapse of a predetermined period of time after the heating roller fusing heater lamp lights up. • The difference between the maximum and minimum temperatures detected by the heating roller thermistor/C within a predetermined period of time after the start of a warm-up cycle is below or above a predetermined value. • The temperature detected after a pressure level correction remains under a predetermined level even after the lapse of a predetermined period of time after the start of the temperature detection. • During a warm-up, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. |
| Causes: | • Fusing unit • C3421: Fusing temperature sensor/1 (TEM1: center) • C3426: Fusing temperature sensor/1 (TEM1: edge) • DC power supply (DCPS) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3721 |
| Description: | Fusing abnormally high temperature detection (heating side) • The heating roller thermistor continues to detect a temperature higher than a predetermined one for a predetermined period of time. • Hard protection signal L is detected continuously over a predetermined period of time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3722 |
| Description: | Fusing abnormally high temperature detection (Edge of the heating side) Detected temperature of the heating roller thermistor/1 (TH1) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3731 |
| Description: | Fusing abnormally high temperature (Hard protector). An abnormally high temperature of the hard protector signal is detected. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • Fusing belt temperature sensor/2 (TEMS2) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/2 (TEMS2) (bizhub 808/758) • Fusing belt temperature sensor/3 (TEMS3) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/3 (TEMS3) (bizhub 808/758) • Pressure roller thermistor/2 (TH3) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1, TEMS2, TEMS3-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Replace the fusing unit. 6. Replace TEMS1, TEMS2, TEMS3. 7. Replace MFPB. |
| Error code: | C3821 |
| Description: | Fusing abnormally low temperature detection (heating side) • The heating roller thermistor continues to detect a temperature lower than a predetermined one for a predetermined period of time. • In the states other than a warm-up operation, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. • The power supply frequency cannot be detected. |
| Causes: | • Fusing unit • C3821: Thermistor/1 (TH1) • C3822: Thermistor/2 (TH2) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3822 |
| Description: | Fusing abnormally low temperature detection (Edge of the heating roller) The heating roller thermistor/3 continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, IHPU, NF1 and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace IHPU. 6 Replace PRCB. 7 Replace NF1. |
| Error code: | C3921 |
| Description: | Fusing sensor wire breaks detection (Center of the heating roller) • At the warm-up stage, the heating roller temperature sensor/2 voltage does not decrease by predetermined steps (temperature rise) within a predetermined time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, PRCB and REDB for proper connection and correct or change as necessary. - - 4 Change TEMS1, TEMS2 or TEMS3 - - 5 Change fusing unit - - 6 Change IHPU - - 7 PRCB ICP17 conduction check - - 8 Change PRCB - - 9 Change REDB |
| Error code: | C3922 |
| Description: | Fusing sensor wire breaks detection (Edge of the heating roller) After a predetermined period of time after the warm-up stage is started, the heating roller thermistor/1 (TH1) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C40A1 |
| Description: | Mechanical controller sub-CPU communication error. A CPU communication error is detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. MFPB F3E conduction check 4. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.60. C40A1 - C40A4, C5372, C5601 - C5606, CA051 - CA053, CC151, CC152, CC170 - CC186, CC191 - CC216, CD211 - CD242, CD401 - CD413, CD701 - CD703, CD705, CD706, CE001, CE003 - CE305, CEEE1, CEEE3) |
| Error code: | C40A2 |
| Description: | Mechanical controller PF communication data error. A CPU communication error is detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. MFPB F3E conduction check 4. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.60. C40A1 - C40A4, C5372, C5601 - C5606, CA051 - CA053, CC151, CC152, CC170 - CC186, CC191 - CC216, CD211 - CD242, CD401 - CD413, CD701 - CD703, CD705, CD706, CE001, CE003 - CE305, CEEE1, CEEE3) |
| Error code: | C40A3 |
| Description: | Mechanical controller PF transmission timeout. A CPU communication error is detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. MFPB F3E conduction check 4. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.60. C40A1 - C40A4, C5372, C5601 - C5606, CA051 - CA053, CC151, CC152, CC170 - CC186, CC191 - CC216, CD211 - CD242, CD401 - CD413, CD701 - CD703, CD705, CD706, CE001, CE003 - CE305, CEEE1, CEEE3) |
| Error code: | C40A4 |
| Description: | Mechanical controller PF communication pulse error. A CPU communication error is detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. MFPB F3E conduction check 4. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.60. C40A1 - C40A4, C5372, C5601 - C5606, CA051 - CA053, CC151, CC152, CC170 - CC186, CC191 - CC216, CD211 - CD242, CD401 - CD413, CD701 - CD703, CD705, CD706, CE001, CE003 - CE305, CEEE1, CEEE3) |
| Error code: | C4101 |
| Description: | BD initialization error |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4501 |
| Description: | Laser malfunction. • SOS signal is not detected even after the lapse of a given period of time after starting the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Causes: | • PH unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between the PH unit-PHRYB CN8 for proper connection and correct as necessary. 2. Replace the PH unit. 3. PHRYB IC5 conduction check. 4. Replace PHRYB. 5. Replace MFPB. |
| Error code: | C5102 |
| Description: | Main high-voltage error C |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5103 |
| Description: | Main high-voltage error M |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5354 |
| Description: | Exhaust fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Ozone ventilation fan (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM4 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM4 operation check PRCB CN3PRCB-14 (ON) PRCB CN3PRCB-16 (LOCK) D-6. 4 Change FM4. 5 Change PRCB. |
| Error code: | C5356 |
| Description: | Cooling fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | Cooling fan motor (FM3) Printer control board (PRCB) |
| Remedy: | 1 Check the FM3 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM3 operation check PRCB CN15-4 (REM) PRCB CN15-6 (LOCK) K-7 to 8 4 Change FM3 - - 5 PRCB ICP6 conduction check - - 6 Change MFPB |
| Error code: | C5359 |
| Description: | Reverse cooling fan failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Reverse cooling fan (FM5) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM5-relay CN88-relay CN20-MFPB CN25E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM5 operation check. • Control signal: MFPB CN25E-11 (REM), MFPB CN25E-13 (LOCK) • Location of electrical component: 18-C 4. Replace FM5. 5. Replace MFPB. |
| Error code: | C5370 |
| Description: | Rear side cooling fan’s failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan remains stationary. |
| Causes: | • MFP control board cooling fan (FM17) • MFP board (MFPB) |
| Remedy: | 1 Check the connector between FM3-MFPB PJ26 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM3 operation check MFPB PJ26 (LOCK) 7-P. 4 Replace FM3. 5 Replace MFPB. |
| Error code: | C5372 |
| Description: | MFP control board CPU temperature failure. Temperature failure of CPU on the MFP board was detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Reboot the machine. 2. Check for clogging in the ventilation path between the MFPB and the power supply cooling fan, and correct as necessary. 3. Replace MFPB. |
| Error code: | C5501 |
| Description: | AC signal abnormality The zero cross signal is not input during fusing phase control. |
| Causes: | • Fusing unit • DC power supply (DCPU) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU and PRCB for proper connection and correct or change as necessary. 3 Replace fusing unit. 4 Replace PRCB. 5 Replace DCPU. |
| Error code: | C5601 |
| Description: | Engine control malfunction. Engine control malfunction is detected with port monitor control. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | C5605 |
| Description: | Engine communication data error. A communication error is detected between CPUs. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.60. C40A1 - C40A4, C5372, C5601 - C5606, CA051 - CA053, CC151, CC152, CC170 - CC186, CC191 - CC216, CD211 - CD242, CD401 - CD413, CD701 - CD703, CD705, CD706, CE001, CE003 - CE305, CEEE1, CEEE3) |
| Error code: | C5606 |
| Description: | Engine transmission timeout. A communication error is detected between CPUs. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.60. C40A1 - C40A4, C5372, C5601 - C5606, CA051 - CA053, CC151, CC152, CC170 - CC186, CC191 - CC216, CD211 - CD242, CD401 - CD413, CD701 - CD703, CD705, CD706, CE001, CE003 - CE305, CEEE1, CEEE3) |
| Error code: | C6102 |
| Description: | Drive system home sensor malfunction • The scanner home sensor (PS201) is unable to detect the scanner located at its home position. • The scanner home sensor (PS201) is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor (PS201) detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor (PS201). |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6103 |
| Description: | Slider over running The scanner home sensor (PS201) detects the scanner at its home position during a period of time that begins with the time when a prescan command and a scan preparation command are executed and ends when a home return command is executed. |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6704 |
| Description: | Image input time out. Image data is not input from the scanner to the MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Memory Bus Check] -> [Scanner -> Memory], and conduct the memory bus function. 2. Correct the harness connection between scanner section and MFPB if faulty. 3. MFPB F3E conduction check 4. Replace MFPB. 5. Replace the CCD unit. |
| Error code: | C6751 |
| Description: | CCD gain adjustment failure. • The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment. |
| Causes: | • LED exposure unit • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 2. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 3. Correct the harness connection between SCDB CN1-DCPU CN005 if faulty. 4. Check for possible extraneous light and correct as necessary. 5. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 6. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 7. Replace SCDB 8. Replace the CCD unit. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | C6752 |
| Description: | ASIC clock input error (front side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on CCD board (CCDB) was conducted, and verification failure was detected. |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Correct the harness connection of CCDB if faulty. 2. Replace the CCD unit. 3. MFPB F3E conduction check 4. Replace MFPB. |
| Error code: | C6756 |
| Description: | CCD power-supply voltage malfunction. Power is not supplied to CCD after the lapse of a given period of time after the main power switch is turned ON or the machine recovers from the sleep mode. |
| Causes: | • CCD board (CCDB) • Scanner drive board (SCDB) • DC power supply unit (DCPU) |
| Remedy: | 1. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 2. Correct the harness connection between SCDB CN1 and DCPU CN005 if faulty. 3. Replace the CCD unit. 4. Replace SCDB. 5. Replace DCPU. |
| Error code: | C6F01 |
| Description: | Scanner sequence trouble 1. The original transport interval becomes shorter than the predetermined value due to an original transport control error in original reading in DF. |
| Causes: | • MFP board (MFPB) • DF control board (DFCB) |
| Remedy: | 1. Correct the harness connection between main body and DF if faulty. 2. Replace DFCB. 3. Replace MFPB. |
| Error code: | C8101 |
| Description: | Before reading pressure welding alienation mechanism trouble. • During a pressure motion being performed, the before read sensor (PS6) output does not change from H to L. • During a retraction motion being performed, the before read sensor (PS6) output does not change from L to H. |
| Causes: | • Reading roller pressure/retraction motor (M6) • Before read sensor (PS6) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M6-relay CN118-DFCB CN4 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-relay CN120-DFCB CN11 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: DFCB CN11-2 (ON) • Location of electrical component: DF 1-C 5. M6 operation check • Control signal: DFCB CN4-1 to 2 • Location of electrical component: DF 10-C 6. Replace M6. 7. DFCB ICP9 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8107 |
| Description: | Glass cleaning mechanism trouble. The front side cleaning home sensor (PS18) is not turned ON (unblocked) even after the set period of time has elapsed after the front side cleaning motor (M8) turned ON. |
| Causes: | • Front side cleaning motor (M8) • Front side cleaning home sensor (PS18) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M8-DFCB CN14 for proper connection and correct as necessary. 2. Check the connector between PS18-DFCB CN18 for proper connection and correct as necessary. 3. Check the connector of M8 for proper drive coupling and correct as necessary. 4. PS18 I/O check, sensor check • Control signal: DFCB CN18-3 (ON) • Location of electrical component: DF 3-C 5. M8 operation check • Control signal: DFCB CN14-1 to 4 • Location of electrical component: DF 6-C 6. Replace M8. 7. DFCB ICP8 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8401 |
| Description: | Nonvolatile memory error. The EEPROM writing is disabled. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Check the DFCB connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Replace DFCB. |
| Error code: | C9401 |
| Description: | Exposure LED lighting failure The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | C9402 |
| Description: | Exposure LED lighting abnormally The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | CA051 |
| Description: | Standard controller configuration failure • The controller of the printer control board (PRCB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA052 |
| Description: | Controller hardware error • A controller hardware error is detected in the network I/F. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA053 |
| Description: | Controller start failure • A controller start failure is detected in the controller interface. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CC140 |
| Description: | Trouble related to security. |
| Causes: | Trouble related to security. |
| Remedy: | Contact the responsible people of KM before taking some countermeasures. |
| Error code: | CC151, CC152 |
| Description: | • CC151: ROM contents error upon startup (MSC) • CC152: ROM contents error upon startup (IR) • CC151: A fault is detected in a sequence of ROM contents check of the MSC during starting. • CC152: A fault is detected in a sequence of ROM contents check of the IR during starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the ROM version. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CC155 |
| Description: | Finisher ROM error |
| Causes: | FS control board (FSCB) |
| Error code: | CC156 |
| Description: | DF ROM error. Data of flash ROM of the DF is determined to be faulty when the main power switch is turned ON. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace DFCB. |
| Error code: | CC15B |
| Description: | Flash ROM error (saddle). <When FS-536SD or FS-537SD is installed> Data of flash ROM of the saddle is determined to be faulty when the main power switch is turned ON. |
| Causes: | SD control board (SDCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace SDCB. (FS-536SD/FS-537SD) |
| Error code: | CC163 |
| Description: | ROM contents error (PRT) • The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Rewrite the firmware. 2 Change PRCB 2.1. Turn OFF the power switch and replace the current PRCB with a new one. (When using a PRCB of another machine in service, be sure to use a PRCB installed in the same model.) 2.2. Update the PRCB firmware. 2.3. After completing the firmware update, turn OFF and ON the power switch and check to see that warm-up is started. 2.4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SV ERB. 3 Change SV ERB 3.1. Replace the current SV ERB with a new one. 3.2. Turn ON the power switch and check to see that warm-up is started. (One minute is spent to prepare the new SV ERB for use. During the period, the control panel backlight stays off.) 3.3. Make the specified readjustments. 4 If the above actions do not solve the problem, contact KMBT. |
| Error code: | CC164 |
| Description: | ROM contents error (MSC) • The wrong model of firmware is detected in the MFP board when the power switch is turned ON. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the corresponding board. 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CC170 ... CC186 |
| Description: | • CC170: Dynamic link error during starting (AP0) • CC171: Dynamic link error during starting (AP1) • CC172: Dynamic link error during starting (AP2) • CC173: Dynamic link error during starting (AP3) • CC174: Dynamic link error during starting (AP4) • CC180: Dynamic link error during starting (LDR) • CC181: Dynamic link error during starting (IBR) • CC182: Dynamic link error during starting (IID) • CC183: Dynamic link error during starting (IPF) • CC184: Dynamic link error during starting (IMY) • CC185: Dynamic link error during starting (SPF) • CC186: Dynamic link error during starting (OAP) A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. If the malfunction code "CC172" has occurred, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if "Controller 1," or "Others" is set for [Image Controller Setting]. If any of these is set, select “Controller 0”. 2. If the malfunction code "CC180" has occurred, check to install the appropriate loadable device driver for an authentication unit which is installed to the MFP. When the appropriate loadable device driver is not installed, reinstall the appropriate loadable device driver. 3. Replace MFPB. 4. If the above actions do not solve the problem, contact KM. |
| Error code: | CC190 |
| Description: | Outline font load error. An error occurred while loading the outline font. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Format the hard disk. 4. Replace the hard disk. (HDD (A) / HDD (B)) 5. Replace MFPB. |
| Error code: | CC191 |
| Description: | Setting parameter load error (LDR). Upon startup, the processing of the loadable device driver setting data file failed. • RAM disk file creation failed. • Reading from the flash ROM failed. • An error occurred in API of the authentication module. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON. 2. Reinstall the loadable device driver. 3. Rewrite the firmware. 4. Replace MFPB. |
| Error code: | CC211 |
| Description: | Authentication device general error. When using the authentication device, authentication data is not to meet the specifications. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. |
| Error code: | CC212 |
| Description: | User validation error. • An error occurred while validating the user authentication information. • The loadable device driver is not successfully installed. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. When this trouble code is generated after installing the loadable device driver, check to see if there is any file other than loadable device driver in USB memory used. If there is any file, reinstall the loadable device driver. 2. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 3. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 4. Re-register the user authentication information. 5. Replace authentication device. |
| Error code: | CC213 |
| Description: | User registration error/Card information setting error. • IC card advanced settings data is not correct when starting-up the authentication device. • Authentication information data is not correct when starting-up the authentication device. • IC card advanced settings data is not correct when setting the IC card advanced settings. • Authentication information data is not correct when setting the IC card advanced settings. • IC card advanced settings data is not correct when registering the authentication information. • Authentication information data is not correct when registering the authentication information. • IC card advanced settings data is not correct when editing the authentication information. • Authentication information data is not correct when editing the authentication information. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 3. Reset the authentication settings. (card type, IC card advanced settings, and etc.) 4. Re-register the user authentication information. |
| Error code: | CC214 |
| Description: | User information deletion error. The deletion of the user information is uncompleted. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. |
| Error code: | CC216 |
| Description: | Acquisition failure of the number of trials/Initialize error of number of authentication. An error occurred during user authentication using optional authentication unit AU-102. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 3. Reset the number of authentication trials. |
| Error code: | CD002 |
| Description: | JOB RAM save error • The error in save of JOB data to the memory/ hard disk and its read error are detected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB. |
| Error code: | CD004, CD00F, CD020 |
| Description: | • CD004: Hard disk access error (connection failure) • CD00F: Hard disk data transfer error • CD020: Hard disk verify error • CD004: Unable to communicate between the hard disk and MFP board (MFPB). • CD00F: Data transfer from the hard disk is faulty. • CD020: The data abnormality is detected by the hard disk verify check. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Reinstall the hard disk. 4. Replace the hard disk. (HDD (A) / HDD (B)) 5. Replace MFPB. |
| Error code: | CD010 |
| Description: | Hard disk unformat. Unformatted hard disk is connected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Carry out the [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format]. 2. Replace the hard disk. (HDD (A) / HDD (B)) 3. Replace MFPB. |
| Error code: | CD011 |
| Description: | Hard disk out of specifications mounted. A hard disk that falls outside the specifications is connected. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD012 |
| Description: | Mount error due to hard disk being unformatted. • The hard disk is not logically formatted after the whole data in the hard disk has been deleted by overwriting. • The hard disk that has replaced an old one is not logically formatted. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Logically format the hard disk and then upgrade the firmware. 2. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD030 |
| Description: | Hard disk management information reading error. The machine fails to read administrative information data saved in the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Logically format the hard disk. 4. Physically format the hard disk. 5. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD041 ... CD046 |
| Description: | HDD command execution error. The error occurred inside the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD047 ... CD04B |
| Description: | HDD SCSI library error. The error occurred inside the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD050 |
| Description: | Hard disk recovery timeout. The hard disk fails to recover from the power save mode within the predetermined period of time. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Reinstall the hard disk. 4. Format the hard disk. 5. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD110 |
| Description: | Wireless LAN destination initialization error. When an initialization error occurred on the settings of the wireless LAN in the upgrade kit (UK-212/UK-215). |
| Remedy: | 1. Check the UK-212 or UK-215 connector for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Reinstall the UK-212or UK-215. |
| Error code: | CD201, CD202, CD203 |
| Description: | • CD201: File memory mounting error • CD202: Memory capacity discrepancy • CD203: Memory capacity discrepancy 2 CD201: • The file memory is not mounted. • The file has any abnormality. CD202: • File memory capacity on the MFP board (MFPB) is not enough. • File memory capacity necessary for duplex printing is not enough. CD203: File memory capacity on the MFP board (MFPB) is not enough. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Replace MFPB. |
| Error code: | CD211, CD212 |
| Description: | • CD211: PCI-SDRAM DMA operation failure • CD212: Compression/extraction timeout detection • CD211: Hardware related to the transfer of memory image of the MFP board (MFPB) fails to respond. • CD212: Hardware related to the BTC compression function of the MFP board (MFPB) fails to respond. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Replace MFPB. |
| Error code: | CD241, CD242 |
| Description: | • CD241: Encryption ASIC setting error • CD242: Encryption ASIC mounting error • CD241: Initialization error of the encrypted ASIC is detected during the machine is starting. • CD242: The faulty of the installation of encrypted ASIC is detected during the machine is starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the MFP board connector for proper connection and correct as necessary. 2. Replace MFPB |
| Error code: | CD261 |
| Description: | USB hub board failure. • When a failure is detected in USB hub board included in the local interface kit. • Non-standard USB device is connected. |
| Causes: | • MFP board (MFPB) • USB hub board (USBHB: EK-610/EK-611) |
| Remedy: | 1. Check the operation with another USB device. 2. Check the USB hub board connector for proper connection and correct as necessary. 3. Replace the USB hub board. 4. Replace MFPB. |
| Error code: | CD262 |
| Description: | Extension network adapter installation error. • When the 2nd network card settings is set to “Set” but the upgrade kit (UK-212/UK-215) is not installed. • Upgrade Kit (UK-212/UK-215) is faulty. |
| Remedy: | 1. Check the settings of [Service Mode] -> [Network Settings] -> [2nd Network Setting] -> [2nd network card settings]. 2. Check the UK-212 or UK-215 connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Reinstall the UK-212 or UK-215. |
| Error code: | CD271 |
| Description: | The memory cannot be recognized with the i-Option activated. While the i-Option is activated, the memory on an MFPB cannot be recognized. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CD272 |
| Description: | i-Option activated and HDD not installed. While the i-Option is activated, the hard disk is not installed. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) |
| Remedy: | 1. Access [Service Mode] -> [System 2] -> [HDD] and check to see if “Installed” is selected. 2. Replace the hard disk (A). 3. Replace MFPB. |
| Error code: | CD300 ... CD370 |
| Description: | CD3##: Nonvolatile data error CD370: Nonvolatile data multiple errors. CD3##: Abnormality is detected by the abnormal check of each nonvolatile data. CD370: Multiple errors (over 5) are detected by the abnormal check of each nonvolatile data. |
| Remedy: | NOTE • Trouble code [C-D370] will be displayed when multiple errors (over 5) of nonvolatile data are detected, which can be restored with one restoration command. • Data backup will be automatically performed every hour. Backup can also be performed manually with the following setting. [Service Mode] -> [Enhanced Security] -> [Memory Data Backup] 1. When a trouble caused by nonvolatile data error occurs, the screen below appears. 2. Select [Yes]. 3. The screen will be shifted to the data restoration screen to perform data restoration. NOTE • When the restoration is performed in a short time, data restoration screen may not be displayed. 4. Check the message which indicates that the data restoration was successfully conducted. Turn OFF the main power switch and turn it ON again more than 10 seconds after. NOTE • In case it failed to restore data, return to the trouble code screen. |
| Error code: | CD390 |
| Description: | Nonvolatile data checksum error. Checksum error is detected while nonvolatile data is being checked for error by each data. (The MFP board is replaced with a new one.) |
| Remedy: | 1 Touch [Yes] on the restore screen displayed on the control panel to restore data. - - NOTE • Do not replace the printer control board and SSD board at the same time with new ones or ones removed from other machines. The backup data will be lost and image failure may be caused. |
| Error code: | CD3A0 |
| Description: | Counter error. The total counter values provided by the MFP board and the eMMC board are different. |
| Causes: | • MFP board (MFPB) • eMMC board (eMMC) |
| Remedy: | 1. If this error occurs temporarily due to the use of the board removed from another machine, reinstall the original board. 2. Replace the current MFPB with a new one. |
| Error code: | CD401 ... CD413 |
| Description: | • CD401: NACK command incorrect • CD402: ACK command incorrect • CD403: Checksum error • CD404: Receiving packet incorrect • CD405: Receiving packet analysis error • CD406: ACK receiving timeout • CD407: Retransmission timeout • CD411: Touch panel board error • CD412: Touch panel type mismatch • CD413: Electrostatic touch panel operation mode error When abnormality is found in the communication of controller. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check whether there is a strong electromagnetic noise source near the main body. 2. Check the connectors on MFPB for proper connection and correct as necessary. 3. Replace MFPB. |
| Error code: | CD601, CD602, CD603 |
| Description: | Trouble related to security. |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. If the above actions do not solve the problem, contact KM. |
| Error code: | CD701, CD702, CD703 |
| Description: | • CD701: Mechanical controller flash ROM writing error • CD702: Mechanical controller flash ROM device error • CD703: FW download communication fault CD701: A mechanical controller flash ROM writing sequence is interrupted in its mid-operation due to, for example, power being shut off. CD702: An erase error or other device fault occurs during mechanical controller flash ROM writing. CD703: • Irregular data is received during FW downloading. • Places are changed in the order of write completion pulses. • A write completion pulse is received for a memory for which binary writing is not permitted. • Final checksum mismatch in FW download • Two-minute timeout (no response from CTL, the number of transfer data items less than the specified) |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CD704 |
| Description: | Finisher Flash ROM device error (When FS-536, FS-536SD, FS-537, or FS-537SD is installed) An erase error or other device fault occurs during the finisher flash ROM writing. |
| Causes: | FS control board (FSCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace FSCB. (FS-536/FS-536SD/FS-537/FS-537SD) |
| Error code: | CD705, CD706 |
| Description: | • CD705: Mechanical controller sub-CPU flash ROM device error • CD706: Mechanical controller sub-CPU flash ROM error • CD705: An erase error or other device fault occurs during mechanical controller sub-CPU flash ROM writing. • CD706: A data error is determined to exist in the mechanical controller sub-CPU flash ROM during starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CDF50, CDF70, CDFA0 |
| Description: | • CDF50: ASIC image version failure • CDF70: ASIC image access failure • CDFA0: ASIC image error Communication error is detected between the MFP board (MFPB) and the CCD board (CCDB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Check the connector between MFPB CN9-CCDB PJ3 for proper connection and correct as necessary. 2. Update the firmware. 3. Replace the CCD unit. 4. Replace MFPB. |
| Error code: | CE001 ... CE007 |
| Description: | Abnormal message queue Task error Event error Memory access error Header access error DIMM initialize error |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the connectors on MFPB for proper connection and correct as necessary. 2 Replace MFPB |
| Error code: | CE002 |
| Description: | Message and method parameter failure. MFP board (MFPB) is faulty. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF the main power switch and turn it ON again, and conduct the following setting. [Service Mode] -> [System 1] -> [Initialization] - > [Clear All Data]. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) 4. Replace MFPB. |
| Error code: | CE101 |
| Description: | Browser finish detected. • The browser is automatically recovered (restarted) after the main body detected that the browser (separate process) has stopped with fault. • When the “Malfunction finish is detected over predetermined number of times” or “the browser task process is except in idle (printing, etc)”. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CE201 |
| Description: | Transmission operation log storage fault. When the transmission log storage failed, it repeats retrial until transmission operation log is stored. The trouble is detected when the retrial failed for predetermined number of times. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CE301 ... CE305 |
| Description: | • CE301: Referring incorrect memory • CE302: Incorrect command • CE303: Finished due to error inside Qt library • CE304: Finished due to error outside Qt library • CE305: Program forced to stop Error occurred with the process inside the MFP controller. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. 3. Acquire the debug logs in [Service Mode] -> [Debug Settings] and analyze them. |
| Error code: | CED01 |
| Description: | The authentication application information does not exist in the hard disk/eMMC board in the enhanced server authentication state. With “Enhanced Server Authentication” set, no authentication application registration information is found in the hard disk or the eMMC board (eMMC). |
| Causes: | • eMMC board (eMMC) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF and ON the main power switch. 2. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 3. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 4. Check the connector from eMMC to MFPB for proper connection and correct as necessary. 5. Logically format the hard disk. 6. Replace the hard disk. (HDD (A) / HDD (B)) 7. If the above actions do not solve the problem, contact KM. |
| Error code: | CEEE1, CEEE3 |
| Description: | • CEEE1: MFP board (MSC) malfunction • CEEE3: MFP board (ENG) malfunction MFP board (MFPB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CEEE2 |
| Description: | Scanner section malfunction. A scanner part is faulty. |
| Causes: | • LED exposure unit • CCD board (CCDB) • Scanner drive board (SCDB) |
| Remedy: | 1. Check the connectors on CCDB or MFPB for proper connection and correct as necessary. 2. Replace SCDB 3. Replace the CCD unit. |
| Error code: | CF0xx |
| Description: | An exceptional instance occurred due to the unexpected parameter in the system F/W. |
| Causes: | MFP board (MFPB) |
| Error code: | CF1xx |
| Description: | Compression malfunctions |
| Causes: | MFP board (MFPB) |
| Error code: | CF2xx |
| Description: | An exceptional instance occurred due to the unexpected parameter in the system F/W. |
| Causes: | MFP board (MFPB) |
| Error code: | CF3xx |
| Description: | Image transfer error on IR input bus |
| Causes: | MFP board (MFPB) |
| Error code: | CF4xx |
| Description: | Communication error (between IR-systems) |
| Causes: | MFP board (MFPB) |
| Error code: | CF5xx |
| Description: | Communication error (IR detected) |
| Causes: | MFP board (MFPB) |
| Error code: | CF6xx |
| Description: | An exceptional instance occurred due to the unexpected parameter in the system F/W. |
| Causes: | • MFP board (MFPB) • Engine |
| Error code: | CF7xx |
| Description: | An exceptional instance occurred due to the unexpected parameter in the system F/W. |
| Causes: | MFP board (MFPB) • Engine • Control panel |
| Error code: | CF8xx |
| Causes: | • MFP board (MFPB) • Engine |
| Error code: | CF9xx |
| Causes: | • MFP board (MFPB) • Engine |
| Error code: | CFAxx |
| Description: | An exceptional instance occurred due to the unexpected parameter in the system F/W. |
| Causes: | MFP board (MFPB) • DIMM (UK-211) • Hard disk (HDD) |
| Error code: | CFB00 ... CFFBD |
| Description: | Abort code |
| Causes: | • MFP board (MFPB) • Hard disk (HDD) • DIMM (UK-211) |
