Konica-Minolta bizhub C200
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Скорость печати
A4
20
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Тип устройства |
МФУ |
Копир |
|
Сканер |
|
Печать фотографий |
|
Телефон |
|
Факс |
|
Цветность печати |
цветная |
Размещение |
напольный |
Тип |
лазерный/светодиодный |
Макс. формат |
A3 |
Технология печати |
лазерная |
Принтер |
|
Прямая печать |
|
Печать без полей |
|
Пигментные чернила |
|
Двусторонняя печать |
|
Время разогрева |
40 |
Макс, разрешение для ч/б печати |
|
| По Y | 600 |
| По X | 600 |
Скорость ч/б печати |
|
| A4 | 20 |
| A3 | 9,8 |
Время выхода первого отпечатка |
|
| Цветн, | 13,5 |
| Ч/б | 10 |
Копир |
|
Шаг масштабирования |
0,1 |
Макс, количество копий за цикл |
999 |
Время выхода первой копии |
10 |
Значение масштаба |
|
| Максимальное | 4 |
| Минимальное | 0,25 |
Макс, разрешение (ч/б) |
|
| По Y | 600 |
| По X | 600 |
Сканер |
|
Оттенки серого |
256 |
Тип сканера |
планшетный |
Макс. формат оригинала |
A3 |
Стандарт TWAIN |
|
Отправка изображения по e-mail |
|
Стандарт WIA |
|
Макс, размер сканирования |
|
| По Y | 487 |
| По X | 311 |
Разрешение сканера |
|
| По Х | 600 |
Расходные материалы |
|
Печать на: |
|
| Глянцевой бумаге |
|
| Карточках |
|
| Конвертах |
|
| Этикетках |
|
| Пленках |
|
| Матовой бумаге |
|
| CD/DVD |
|
| Рулоне |
|
| Фотобумаге |
|
Плотность бумаги |
|
| Максимальная | 256 |
| Минимальная | 64 |
Факс |
|
Цветной |
|
Телефон |
|
Спикерфон |
|
Стандарт DECT |
|
Автоответчик |
|
Caller ID |
|
АОН |
|
Беспроводная трубка |
|
Проводная трубка |
|
Языки управления |
|
| PCL 5e |
|
| PostScript |
|
| PostScript 3 |
|
| PCL 5c |
|
|
|
|
| PPDS |
|
| PCL 6 |
|
| PostScript 2 |
|
Лотки |
|
Подача бумаги |
|
| Максимальная | 3 350 |
| Стандартная | 250 |
Вывод бумаги |
|
| Стандартный | 250 |
Финишер |
|
Сортировка со сдвигом |
|
Брошюровщик |
|
Степлер |
|
Электронная сортировка |
|
Сортер |
|
Интерфейсы |
|
Ethernet (RJ-45) |
|
USB |
|
Инфракрасный порт |
|
RS-232 |
|
Bluetooth |
|
Wi-Fi |
|
Веб-интерфейс |
|
Устройство для чтения карт памяти |
|
FireWire (IEEE 1394) |
|
LPT |
|
Версия USB |
2,0 |
Память/Процессор |
|
Объем памяти |
576 |
Макс, объем памяти |
1 024 |
Дополнительная информация |
|
Экран |
|
Поддержка ОС |
|
| Linux |
|
| Mac OS |
|
| DOS |
|
| Windows |
|
Потребляемая мощность |
|
| При работе | 1 250 |
Габариты |
|
Высота |
648 |
Глубина |
688 |
Ширина |
620 |
Вес |
68 |
Модули
PRINT HEAD SECTION
TONER CONVEYANCE SECTION
REAR ELECTRICAL SECTION
EXTERNAL PARTS 2
PAPER FEED SECTION
SCANNER SECTION 2
VERTICAL CONVEYANCE SECTION 3
TONER CONVEYANCE SECTION 2
PAPER EXIT SECTION 2
TRANSFER BELT UNIT
FUSING SECTION
SCANNER SECTION
VERTICAL CONVEYANCE SECTION 2
IR COVER
ELECTRICAL COMPONENTS
MFBU
PAPER EXIT SECTION
INNER COVER SECTION
Toner collecting Section
CASSETTE TRAY SECTION
MAIN FRAME SECTION
IR DRIVE SECTION
ERASE LAMP SECTION
Fusing Drive Section
EXTERNAL PARTS
Vertical conveyance Section
SIZE DETECT SECTION
LOWER FRAME SECTION
P-H FRAME SECTION
FEED-TRANSPORT DRIVE SECTION
IR FRAME SECTION
HIGH VOLTAGE UNIT
T-C RAIL SECTION
MAIN DRIVE SECTION
Детали FEED-TRANSPORT DRIVE SECTION
| Деталь: | Print Head Kit |
| Парткод: | A02F R70B 11 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 1906 04 |
| Деталь: | BRACKET |
| Парткод: | A02E 1048 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 2187 04 |
| Деталь: | GUIDE |
| Парткод: | A02F 1059 00 |
| Деталь: | GEAR 27T |
| Парткод: | 4038 2189 01 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2190 03 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2191 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2194 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2193 03 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2196 01 |
| Деталь: | GEAR 30T |
| Парткод: | 4038 2188 02 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 2184 01 |
| Деталь: | WASHER |
| Парткод: | 4038 2179 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2180 01 |
| Деталь: | SPRING |
| Парткод: | 4038 2042 01 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | SKEW ADJUSTMENT ASSY |
| Парткод: | A02E R703 00 |
| Деталь: | GEAR 15T |
| Парткод: | A02E 3676 00 |
| Деталь: | GEAR 14T |
| Парткод: | A02E 3677 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 3682 01 |
| Деталь: | WASHER |
| Парткод: | A02E 3687 00 |
| Деталь: | SCREW |
| Парткод: | A02E 3674 01 |
| Деталь: | SEAL |
| Парткод: | A02E 3684 00 |
| Деталь: | Transport Pipe K |
| Парткод: | A02E 3673 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 3681 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3679 01 |
| Деталь: | INSULATING MEMBER |
| Парткод: | A02E 1047 00 |
| Деталь: | SEAL |
| Парткод: | 4038 2056 02 |
| Деталь: | DUCT |
| Парткод: | 4038 2052 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2053 02 |
| Деталь: | SHUTTER |
| Парткод: | A02E 3603 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3604 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 3602 00 |
| Деталь: | PIPE |
| Парткод: | A02E 3601 01 |
| Деталь: | SCREW |
| Парткод: | A02E 3671 01 |
| Деталь: | Transport Pipe CMY |
| Парткод: | A02E 3670 00 |
| Деталь: | GEAR 18T |
| Парткод: | A02E 3637 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 3683 00 |
| Деталь: | PIN |
| Парткод: | A02E 3678 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 3680 00 |
| Деталь: | BRACKET |
| Парткод: | A02F 1482 00 |
| Деталь: | BRACKET |
| Парткод: | A02F 1472 00 |
| Деталь: | REAR COVER |
| Парткод: | 4039 1016 01 |
| Деталь: | PWB assembly (PWB-EE1 ASSY) |
| Парткод: | A02E H002 01 |
| Деталь: | BRACKET |
| Парткод: | A02F 1486 00 |
| Деталь: | LABEL |
| Парткод: | 9J06 7301 01 |
| Деталь: | POWER CORD |
| Парткод: | 4037 0775 01 |
| Деталь: | BRACKET |
| Парткод: | A02F 1495 00 |
| Деталь: | COVER |
| Парткод: | A02F 1671 02 |
| Деталь: | COVER |
| Парткод: | A02F 1688 01 |
| Деталь: | REAR COVER |
| Парткод: | A02F 1625 01 |
| Деталь: | RIGHT COVER |
| Парткод: | A02F 1629 02 |
| Деталь: | Cover Manu |
| Парткод: | A02F 1640 02 |
| Деталь: | LEFT COVER |
| Парткод: | A02F 1628 01 |
| Деталь: | REAR COVER |
| Парткод: | A02F 1638 02 |
| Деталь: | SEAL |
| Парткод: | A02F 1617 01 |
| Деталь: | SEAL |
| Парткод: | A02F 1679 00 |
| Деталь: | COVER |
| Парткод: | A02F 1677 00 |
| Деталь: | WEIGHT |
| Парткод: | A02F 6263 00 |
| Деталь: | WASHER |
| Парткод: | 4036 3030 01 |
| Деталь: | WASHER |
| Парткод: | 4036 3031 01 |
| Деталь: | SPACER |
| Парткод: | 4039 5602 00 |
| Деталь: | WASHER |
| Парткод: | 4011 3020 01 |
| Деталь: | WASHER |
| Парткод: | 1164 3066 01 |
| Деталь: | ROLLER |
| Парткод: | 4034 3012 01 |
| Деталь: | SHAFT |
| Парткод: | 4004 3001 02 |
| Деталь: | COLLAR |
| Парткод: | 4004 3005 01 |
| Деталь: | STOP RING |
| Парткод: | 4658 3046 01 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | 4034 0151 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 5654 00 |
| Деталь: | SHAFT |
| Парткод: | 4658 3040 01 |
| Деталь: | COLLAR |
| Парткод: | 4038 5655 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4004 3006 03 |
| Деталь: | BEARING |
| Парткод: | A02F 6203 00 |
| Деталь: | STOPPER |
| Парткод: | 4039 5601 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4036 3040 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4036 3018 01 |
| Деталь: | PIN |
| Парткод: | 4036 3014 01 |
| Деталь: | PAWL |
| Парткод: | 1164 3004 03 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1164 3005 02 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4038 R748 00 |
| Деталь: | Inverter unit |
| Парткод: | A02F PPOY 00 |
| Деталь: | SLIDER |
| Парткод: | 4551 2017 01 |
| Деталь: | HOLDER |
| Парткод: | A02F PP1F 00 |
| Деталь: | FlatCable |
| Парткод: | A02F PP1D 00 |
| Деталь: | SCREW |
| Парткод: | A02F PP1K 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 7128 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 3559 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3537 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3539 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3538 01 |
| Деталь: | Label Jam/M1 |
| Парткод: | A02E 9406 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 7129 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 3536 01 |
| Деталь: | ROLLER |
| Парткод: | A02E 7001 00 |
| Деталь: | ROLLER |
| Парткод: | 4038 3502 02 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 7023 00 |
| Деталь: | FIXED POWER RESISTORS |
| Парткод: | V800 5003 00 |
| Деталь: | BUSHING |
| Парткод: | 4025 3572 01 |
| Деталь: | GEAR 20T |
| Парткод: | 4004 3503 02 |
| Деталь: | GEAR 14T |
| Парткод: | 4004 3504 02 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 3525 01 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 7130 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3567 01 |
| Деталь: | SEAL |
| Парткод: | 4128 3522 02 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A02E M505 00 |
| Деталь: | ACTUATOR |
| Парткод: | 4038 3562 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 1164 3527 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 3561 03 |
| Деталь: | HOLDER |
| Парткод: | A02E 7057 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 7126 01 |
| Деталь: | COVER |
| Парткод: | A02E 7058 01 |
| Деталь: | Photo sensing |
| Парткод: | A02E M500 00 |
| Деталь: | Toner Detection harness |
| Парткод: | A02E N10B 00 |
| Деталь: | SPACER |
| Парткод: | 4038 3597 01 |
| Деталь: | WASHER |
| Парткод: | 4038 3593 01 |
| Деталь: | FRAME |
| Парткод: | A02E 1006 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3592 01 |
| Деталь: | SPACER |
| Парткод: | 4038 5603 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A02E 7132 01 |
| Деталь: | CLUTCH |
| Парткод: | A02E M200 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 3540 03 |
| Деталь: | Vertical Transport |
| Парткод: | A02F R7A5 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 3616 01 |
| Деталь: | COVER |
| Парткод: | A02E 3615 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3619 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 3614 00 |
| Деталь: | GEAR 22T |
| Парткод: | A02E 3626 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 3625 00 |
| Деталь: | COIL |
| Парткод: | A02E 3613 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3617 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 3618 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 2452 01 |
| Деталь: | GEAR 35T |
| Парткод: | A02E 2451 00 |
| Деталь: | BUSHING |
| Парткод: | 4004 5339 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 2586 01 |
| Деталь: | Gear 26/34T |
| Парткод: | A02E 2450 00 |
| Деталь: | Gear 30/30T |
| Парткод: | A02E 2579 00 |
| Деталь: | GEAR 18/30T |
| Парткод: | 4004 2545 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 2453 02 |
| Деталь: | PIPE |
| Парткод: | A02E 3611 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2143 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2114 01 |
| Деталь: | SHUTTER |
| Парткод: | A02E 3628 00 |
| Деталь: | CAP |
| Парткод: | A02E 3631 00 |
| Деталь: | BRACKET |
| Парткод: | A02F 3634 00 |
| Деталь: | SEAL |
| Парткод: | A02F 1481 00 |
| Деталь: | GEAR 18T |
| Парткод: | A02E 3627 00 |
| Деталь: | Gear 43T |
| Парткод: | A02F 3635 00 |
| Деталь: | Gear 27/48T |
| Парткод: | A02E 3622 00 |
| Деталь: | Caulking (Drive) |
| Парткод: | A02F R7A3 00 |
| Деталь: | Gear 44/26T |
| Парткод: | A02F 3636 00 |
| Деталь: | Gear 22/37T |
| Парткод: | A02E 3630 00 |
| Деталь: | LEVER |
| Парткод: | A02F 8973 00 |
| Деталь: | GEAR 32T |
| Парткод: | 9J06 5925 02 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 5872 02 |
| Деталь: | GEAR 16/20T |
| Парткод: | A02F 8971 00 |
| Деталь: | TENSION SPRING |
| Парткод: | A02F 8981 00 |
| Деталь: | LEVER |
| Парткод: | A02F 8956 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 5864 01 |
| Деталь: | HOLDER |
| Парткод: | A02F 8950 01 |
| Деталь: | GEAR 25T |
| Парткод: | A02F 8977 00 |
| Деталь: | ROLLER |
| Парткод: | A02E 8910 00 |
| Деталь: | ROLL |
| Парткод: | 4131 3904 02 |
| Деталь: | BUSHING |
| Парткод: | 4038 5860 01 |
| Деталь: | SHAFT |
| Парткод: | 4025 5984 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | SPACER |
| Парткод: | A02E 8916 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 8906 00 |
| Деталь: | COVER |
| Парткод: | A02E 8903 00 |
| Деталь: | GEAR 16T |
| Парткод: | A02E 8952 00 |
| Деталь: | Gear 34/27T |
| Парткод: | A02F 8970 00 |
| Деталь: | GEAR 24T |
| Парткод: | A02F 8972 00 |
| Деталь: | GEAR 17/16T |
| Парткод: | 4038 5871 02 |
| Деталь: | GEAR 24/20T |
| Парткод: | 4038 5877 02 |
| Деталь: | Caulking (Paper Output Drive)2 |
| Парткод: | A02F R7A2 00 |
| Деталь: | Caulking (Paper Output Drive)1 |
| Парткод: | A02F R7A1 00 |
| Деталь: | Drive (Paper Output) |
| Парткод: | A02F R708 00 |
| Деталь: | Transfer Detection Assy |
| Парткод: | A02F R70D 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 1123 00 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 1122 12 |
| Деталь: | BRACKET |
| Парткод: | A02E 1121 11 |
| Деталь: | Connecting Detection harness |
| Парткод: | A02F N10V 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Transfer Wiring /14 |
| Парткод: | A02E N131 00 |
| Деталь: | Transfer Wiring /13 |
| Парткод: | A02E N132 01 |
| Деталь: | Transfer Wiring /2 |
| Парткод: | A02E N130 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | ARM |
| Парткод: | 4038 2027 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2029 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2028 01 |
| Деталь: | LEVER |
| Парткод: | 4038 2026 01 |
| Деталь: | CONTACT |
| Парткод: | A02E 1103 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2205 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2207 01 |
| Деталь: | CONTACT |
| Парткод: | A02E 1104 00 |
| Деталь: | CONTACT |
| Парткод: | A02E 1105 00 |
| Деталь: | RAIL |
| Парткод: | A02E 1102 00 |
| Деталь: | CONTACT |
| Парткод: | A02E 1107 00 |
| Деталь: | RAIL |
| Парткод: | A02E 1101 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2152 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2077 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2078 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2153 13 |
| Деталь: | LEVER |
| Парткод: | 4038 2046 01 |
| Деталь: | ARM |
| Парткод: | 4038 2047 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2080 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2045 01 |
| Деталь: | CONTACT |
| Парткод: | A02E 1108 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2048 01 |
| Деталь: | Transfer Belt Kit |
| Парткод: | A02E R730 11 |
| Деталь: | Fusing Unit 100V |
| Парткод: | A02F R703 00 |
| Деталь: | FUSING UNIT 120V |
| Парткод: | A02F R705 00 |
| Деталь: | FUSING UNIT 230V |
| Парткод: | A02F R706 00 |
| Деталь: | FUSING UNIT 110V |
| Парткод: | A02F R704 00 |
| Деталь: | HOLDER |
| Парткод: | 9J06 2082 01 |
| Деталь: | GUIDE |
| Парткод: | 9J06 2462 01 |
| Деталь: | HOLDER |
| Парткод: | 9J06 2079 01 |
| Деталь: | SEAL |
| Парткод: | A02E 1057 01 |
| Деталь: | GUIDE |
| Парткод: | 9J06 2463 02 |
| Деталь: | Scanner |
| Парткод: | A02F PP02 00 |
| Деталь: | HOLDER |
| Парткод: | A02F PP05 00 |
| Деталь: | FlatCable |
| Парткод: | A02F PP0N 00 |
| Деталь: | SPEAKER |
| Парткод: | A02F PP0T 00 |
| Деталь: | Cusion |
| Парткод: | A02F PP1E 00 |
| Деталь: | REED SWITCH |
| Парткод: | 4551 2010 01 |
| Деталь: | HARNESS |
| Парткод: | A02F PP0P 00 |
| Деталь: | GUIDE |
| Парткод: | A02F PP03 00 |
| Деталь: | Lamp |
| Парткод: | A02F PP0X 00 |
| Деталь: | SLIDER |
| Парткод: | 4551 2017 01 |
| Деталь: | SCREW |
| Парткод: | A02F PP1K 00 |
| Деталь: | COVER |
| Парткод: | A02F 7183 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 3516 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3517 03 |
| Деталь: | Label JAM |
| Парткод: | A02E 9405 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02F 7112 01 |
| Деталь: | COLLAR |
| Парткод: | 4038 3534 01 |
| Деталь: | SHAFT |
| Парткод: | A02F 7114 00 |
| Деталь: | BRACKET |
| Парткод: | A02F 7111 00 |
| Деталь: | STOPPER |
| Парткод: | A02E 7123 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 3511 02 |
| Деталь: | LABEL |
| Парткод: | A02F 9446 00 |
| Деталь: | Label Prohibit |
| Парткод: | A02F 9447 00 |
| Деталь: | COVER |
| Парткод: | A02F 1673 01 |
| Деталь: | Cover IR Front |
| Парткод: | A02F 1670 00 |
| Деталь: | COVER |
| Парткод: | A02F 1705 01 |
| Деталь: | PANEL SHEET |
| Парткод: | A02F 9511 00 |
| Деталь: | PANEL SHEET |
| Парткод: | A02F 9512 00 |
| Деталь: | PANEL SHEET |
| Парткод: | A02F 9514 00 |
| Деталь: | PANEL SHEET |
| Парткод: | A02F 9513 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A02F M700 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A02F M708 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A02F M702 01 |
| Деталь: | COVER |
| Парткод: | A02F 1704 00 |
| Деталь: | Label Emperon |
| Парткод: | A011 9462 00 |
| Деталь: | COVER |
| Парткод: | A02F 1680 01 |
| Деталь: | COVER BACK |
| Парткод: | A02F 1682 02 |
| Деталь: | Cover IR Lower |
| Парткод: | A02F 1678 00 |
| Деталь: | GLASS |
| Парткод: | A02F PP01 00 |
| Деталь: | ORIGINAL GLASS |
| Парткод: | A02F PP00 00 |
| Деталь: | COVER |
| Парткод: | A02F PP04 00 |
| Деталь: | SCREW |
| Парткод: | A02F PP1J 00 |
| Деталь: | SCREW |
| Парткод: | A02F PP1H 00 |
| Деталь: | PWB Assembly(PWB-MC ASSY) |
| Парткод: | A02F H001 04 |
| Деталь: | POWER SUPPLY |
| Парткод: | A02F M400 02 |
| Деталь: | POWER SUPPLY |
| Парткод: | A02F M401 02 |
| Деталь: | SPACER |
| Парткод: | V502 0100 36 |
| Деталь: | SPACER |
| Парткод: | V502 0100 37 |
| Деталь: | BRACKET |
| Парткод: | A02F 1494 00 |
| Деталь: | BRACKET |
| Парткод: | A02F 1485 00 |
| Деталь: | FAN MOTOR |
| Парткод: | A02E M108 01 |
| Деталь: | FILTER |
| Парткод: | A02E 1483 00 |
| Деталь: | FILTER |
| Парткод: | A02E 1484 00 |
| Деталь: | SHIELD |
| Парткод: | A02F 1480 00 |
| Деталь: | PLUG HOUSING |
| Парткод: | V818 6000 15 |
| Деталь: | Control Wiring |
| Парткод: | A02F N10C 01 |
| Деталь: | Memory card |
| Парткод: | A02F PP1G 00 |
| Деталь: | PWB Assembly |
| Парткод: | A02F PP10 00 |
| Деталь: | Control board |
| Парткод: | A02F PP11 00 Old |
| Деталь: | Control board |
| Парткод: | A02F PP1111 |
| Деталь: | SCREW |
| Парткод: | A02F PP1K 00 |
| Деталь: | COVER |
| Парткод: | A02F 8901 00 |
| Деталь: | Label JAM |
| Парткод: | A02E 9414 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | 4038 5856 01 |
| Деталь: | Cooling Wiring |
| Парткод: | A02F N107 01 |
| Деталь: | COVER |
| Парткод: | A02F 8908 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | GUIDE |
| Парткод: | A02F 8976 00 |
| Деталь: | GUIDE |
| Парткод: | A02F 8904 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 8934 00 |
| Деталь: | GROUND |
| Парткод: | A02F 8982 00 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 8905 00 |
| Деталь: | PIN |
| Парткод: | 4036 2549 01 |
| Деталь: | COLLAR |
| Парткод: | A02E 8913 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 8902 03 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | Grounding Wiring |
| Парткод: | A02F N10W 00 |
| Деталь: | Front Cover Switch Assy |
| Парткод: | A02E R709 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 2287 02 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 1384 00 |
| Деталь: | Heater Relay harness |
| Парткод: | A02F N10K 01 |
| Деталь: | BRACKET |
| Парткод: | A02F 1381 00 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06 M601 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2281 04 |
| Деталь: | Supply Detection harness |
| Парткод: | A02E N10N 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2282 03 |
| Деталь: | CONNECTOR PIN |
| Парткод: | V816 3000 02 |
| Деталь: | CONNECTOR |
| Парткод: | V651 0100 40 |
| Деталь: | COVER |
| Парткод: | A02E 1702 00 |
| Деталь: | SUCTION PLATE |
| Парткод: | A02E 1614 01 |
| Деталь: | LABEL |
| Парткод: | A02F 9453 00 |
| Деталь: | SPACER |
| Парткод: | A02E 1618 00 |
| Деталь: | Label Iu |
| Парткод: | A02E 9403 00 |
| Деталь: | Label Tc/Iu |
| Парткод: | A02E 9402 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 1703 00 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038 1014 01 |
| Деталь: | COVER |
| Парткод: | A02E 1701 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2283 02 |
| Деталь: | Photoconductor Detection harness |
| Парткод: | A02E N119 02 |
| Деталь: | SEESAW-SWITCH |
| Парткод: | 4038 M600 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1383 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1300 51 |
| Деталь: | BRACKET |
| Парткод: | A02F 1203 01 |
| Деталь: | AC Wiring /100V |
| Парткод: | A02F N10M 01 |
| Деталь: | AC Wiring |
| Парткод: | A02F N10J 01 |
| Деталь: | DUCT |
| Парткод: | A02E 1161 02 |
| Деталь: | 2nd Front Cover |
| Парткод: | A02F R7A4 00 |
| Деталь: | Waste Toner Box |
| Парткод: | A0DT WY0 |
| Деталь: | RAIL |
| Парткод: | A02E 3650 01 |
| Деталь: | LD Relay harness |
| Парткод: | A02F N10E 01 |
| Деталь: | COVER |
| Парткод: | A02E 3651 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0901 01 |
| Деталь: | Sensor Wiring /3 |
| Парткод: | A02E N10G 00 |
| Деталь: | SHUTTER |
| Парткод: | A02E 3641 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 3644 01 |
| Деталь: | PIPE |
| Парткод: | A02F 3640 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3643 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3642 01 |
| Деталь: | Waste Toner Pipe |
| Парткод: | A02F R701 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4687 3281 01 |
| Деталь: | SEAL |
| Парткод: | A02F 6229 01 |
| Деталь: | BRAKE |
| Парткод: | 4036 3086 01 |
| Деталь: | Label Cd |
| Парткод: | A02F 9443 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02F 6211 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 5601 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4134 3106 01 |
| Деталь: | GUIDE |
| Парткод: | 4004 3040 02 |
| Деталь: | GUIDE |
| Парткод: | 4004 3024 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4004 3033 01 |
| Деталь: | GUIDE |
| Парткод: | 4004 3038 01 |
| Деталь: | SEAL |
| Парткод: | 4004 3008 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1164 3062 01 |
| Деталь: | LEVER |
| Парткод: | 1164 3061 01 |
| Деталь: | LABEL PAPER |
| Парткод: | A02F 9444 00 |
| Деталь: | COVER |
| Парткод: | A02E 6207 00 |
| Деталь: | CASSETTE |
| Парткод: | A02F 6201 02 |
| Деталь: | COVER |
| Парткод: | A02F 6202 02 |
| Деталь: | BRACKET |
| Парткод: | 4004 3031 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LEVER |
| Парткод: | A02F 6251 00 |
| Деталь: | SPACER |
| Парткод: | 4037 3226 01 |
| Деталь: | Label FD |
| Парткод: | A02F 9442 00 |
| Деталь: | RACK |
| Парткод: | A02F 6232 00 |
| Деталь: | LEVER |
| Парткод: | A02F 6214 00 |
| Деталь: | GUIDE |
| Парткод: | 4004 3042 01 |
| Деталь: | GEAR 20T |
| Парткод: | 1164 3045 01 |
| Деталь: | GUIDE |
| Парткод: | 4021 3036 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4037 3223 01 |
| Деталь: | RAIL |
| Парткод: | 4039 5604 00 |
| Деталь: | SPACER |
| Парткод: | 4037 3227 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | A02F 6215 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02F 6212 00 |
| Деталь: | Label Level |
| Парткод: | A02F 9441 00 |
| Деталь: | SEAL |
| Парткод: | A02F 6221 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02F R70A 00 |
| Деталь: | CASSETTE |
| Парткод: | A02F R709 00 |
| Деталь: | BRACKET |
| Парткод: | A02F 1192 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 1191 00 |
| Деталь: | HANDLE |
| Парткод: | A02E 1190 01 |
| Деталь: | PROTECTION |
| Парткод: | 1154 4670 01 |
| Деталь: | CAP |
| Парткод: | A02E 1196 00 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996 3055 01 |
| Деталь: | SEAL |
| Парткод: | 4039 2209 01 |
| Деталь: | SEAL |
| Парткод: | A02E 1207 00 |
| Деталь: | CAP |
| Парткод: | A02E 1195 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1382 00 |
| Деталь: | SPACER |
| Парткод: | V502 0100 36 |
| Деталь: | BRACKET |
| Парткод: | A02E 1014 00 |
| Деталь: | ImageProcessing Wiring |
| Парткод: | A02F N10D 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 1164 3054 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3054 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 1193 00 |
| Деталь: | INSULATING MEMBER |
| Парткод: | A02E 1194 00 |
| Деталь: | BRACKET |
| Парткод: | A02F 1194 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A02F PP0W 00 |
| Деталь: | HARNESS |
| Парткод: | A02F PP0Q 00 |
| Деталь: | MOTOR |
| Парткод: | A02F PP0K 00 |
| Деталь: | PULLEY |
| Парткод: | A02F PP0D 00 |
| Деталь: | TIMING BELT |
| Парткод: | A02F PP0R 00 |
| Деталь: | SCREW |
| Парткод: | A02F PP1K 00 |
| Деталь: | E RING |
| Парткод: | A0EY PP01 00 |
| Деталь: | Eraser Assy Black |
| Парткод: | A02E R706 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1033 11 |
| Деталь: | SHIELD PLATE |
| Парткод: | A02E 1053 11 |
| Деталь: | LED ARRAY |
| Парткод: | A02E M304 00 |
| Деталь: | Eraser (YMC) |
| Парткод: | A02F R70C 00 |
| Деталь: | COVER |
| Парткод: | A02E 1054 00 |
| Деталь: | SHIELD PLATE |
| Парткод: | A02E 1051 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 1035 00 |
| Деталь: | RAIL |
| Парткод: | A02E 1034 00 |
| Деталь: | RAIL |
| Парткод: | A02E 1037 00 |
| Деталь: | Label Iu |
| Парткод: | A02E 9403 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2072 04 |
| Деталь: | SLIDER |
| Парткод: | 4038 2069 01 |
| Деталь: | WASHER |
| Парткод: | A02E 2302 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A02E 2585 00 |
| Деталь: | WASHER |
| Парткод: | A02E 2303 00 |
| Деталь: | Gear 27/85T |
| Парткод: | A02E 2570 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2573 00 |
| Деталь: | PIN |
| Парткод: | 1144 5200 01 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 02 |
| Деталь: | GEAR 34T |
| Парткод: | A02E 2571 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 2310 11 |
| Деталь: | LEVER |
| Парткод: | A02E 2584 01 |
| Деталь: | HOLDER |
| Парткод: | A02F 2557 03 |
| Деталь: | SHAFT |
| Парткод: | A02F 2559 00 |
| Деталь: | BUSHING |
| Парткод: | 9J06 2101 00 |
| Деталь: | GEAR 26T |
| Парткод: | A02F 2541 00 |
| Деталь: | GEAR 16T |
| Парткод: | 9J06 2574 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 2576 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 9J06 2595 02 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2580 01 |
| Деталь: | PLATE |
| Парткод: | A02F 2313 01 |
| Деталь: | GEAR 13T |
| Парткод: | 9J06 2546 01 |
| Деталь: | GEAR 22T |
| Парткод: | 9J06 2575 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 2594 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2587 00 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2592 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 2596 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M200 00 |
| Деталь: | SHAFT |
| Парткод: | A02F 2563 00 |
| Деталь: | GEAR 40T |
| Парткод: | A02E 2545 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2314 00 |
| Деталь: | PIN |
| Парткод: | 4131 2536 02 |
| Деталь: | GEAR 41T |
| Парткод: | 4038 2593 02 |
| Деталь: | SHAFT |
| Парткод: | A02E 2315 00 |
| Деталь: | GEAR 60T |
| Парткод: | 9J06 2543 01 |
| Деталь: | Gear 18/75T |
| Парткод: | A02E 2542 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | HOLDER |
| Парткод: | 9J06 2572 01 |
| Деталь: | PLUG HOUSING |
| Парткод: | V818 6000 14 |
| Деталь: | BRACKET |
| Парткод: | A02F 2317 00 |
| Деталь: | Brushless motor |
| Парткод: | A02E M100 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 2556 12 |
| Деталь: | Gear 17/68T |
| Парткод: | A02E 2544 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2316 00 |
| Деталь: | Gear 16/29T |
| Парткод: | A02E 2591 00 |
| Деталь: | GEAR 27T |
| Парткод: | A02F 2547 00 |
| Деталь: | MOTOR ASSY |
| Парткод: | A02E R714 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 2582 00 |
| Деталь: | Fuser Drive |
| Парткод: | A02F R7A6 00 |
| Деталь: | TRAY |
| Парткод: | A02E 1620 00 |
| Деталь: | TOP COVER |
| Парткод: | A02E 1621 00 |
| Деталь: | COVER |
| Парткод: | A02E 1637 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1615 00 |
| Деталь: | Label IU replace |
| Парткод: | A02F 9448 01 |
| Деталь: | SEAL |
| Парткод: | A02E 1164 00 |
| Деталь: | DUCT |
| Парткод: | A02E 1160 01 |
| Деталь: | SET PLATE |
| Парткод: | 1053 3103 01 |
| Деталь: | BAND |
| Парткод: | A02E 1612 00 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475 2603 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 1046 01 |
| Деталь: | RIGHT COVER |
| Парткод: | A02F 1623 00 |
| Деталь: | Label Number 1 |
| Парткод: | A02E 9418 00 |
| Деталь: | LABEL |
| Парткод: | A02F 9521 00 |
| Деталь: | LABEL |
| Парткод: | A02F 9522 00 |
| Деталь: | LABEL |
| Парткод: | A02F 9445 01 |
| Деталь: | LABEL |
| Парткод: | A02F 9541 00 |
| Деталь: | Label(bizhubC200R) |
| Парткод: | A02F 9543 00 |
| Деталь: | LABEL |
| Парткод: | A02F 9542 00 |
| Деталь: | HINGE |
| Парткод: | A02E 1610 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 1613 00 |
| Деталь: | Logo Mark |
| Парткод: | A00J 9455 00 |
| Деталь: | Label Waste Toner Remove |
| Парткод: | A02E 9404 00 |
| Деталь: | CLEANING PAD |
| Парткод: | 4038 2084 06 |
| Деталь: | CLANING MATERIAL |
| Парткод: | 4038 2083 02 |
| Деталь: | SEAL |
| Парткод: | A02E 1162 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1165 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1163 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1616 00 |
| Деталь: | LEFT COVER |
| Парткод: | A02E 1624 02 |
| Деталь: | Label Only connect |
| Парткод: | A00J 9450 00 |
| Деталь: | Label Mask |
| Парткод: | A02E 1611 00 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | A02E F185 00 |
| Деталь: | COVER |
| Парткод: | A02F 7185 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 7191 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 7192 00 |
| Деталь: | LEVER |
| Парткод: | A02E 7100 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 4611 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 3542 02 |
| Деталь: | CAM |
| Парткод: | 4038 3553 01 |
| Деталь: | LEVER |
| Парткод: | A02E 7051 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 7053 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3520 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 4620 01 |
| Деталь: | COVER |
| Парткод: | A02F 7182 01 |
| Деталь: | GUIDE |
| Парткод: | A02F 7186 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 7023 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 3571 02 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 7054 00 |
| Деталь: | LEVER |
| Парткод: | A02E 7052 01 |
| Деталь: | COVER DUP |
| Парткод: | A02F 1637 01 |
| Деталь: | TRANSFER ROLLER UNIT |
| Парткод: | A02E R713 00 |
| Деталь: | Vertical Conveyance Assy |
| Парткод: | A02F R707 00 |
| Деталь: | Coil spring |
| Парткод: | A02F PP0G 00 |
| Деталь: | PULLEY |
| Парткод: | A02F PP0U 00 |
| Деталь: | WIRE |
| Парткод: | A02F PP09 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A02F PP0W 00 |
| Деталь: | ARM |
| Парткод: | A02F PP0B 00 |
| Деталь: | Coil spring |
| Парткод: | A02F PP0H 00 |
| Деталь: | HOLDER |
| Парткод: | A02F PP0A 00 |
| Деталь: | Coil spring |
| Парткод: | A02F PP0F 00 |
| Деталь: | PULLEY |
| Парткод: | A02F PP0C 00 |
| Деталь: | TIMING BELT |
| Парткод: | A02F PP0S 00 |
| Деталь: | SPACER |
| Парткод: | A02F PP0E 00 |
| Деталь: | SENSOR |
| Парткод: | A02F PP0M 00 |
| Деталь: | PWB Assembly |
| Парткод: | A02F PP06 00 |
| Деталь: | PULLEY |
| Парткод: | A02F PP08 00 |
| Деталь: | PULLEY |
| Парткод: | A02F PP07 00 |
| Деталь: | BALL BEARING |
| Парткод: | 4384 1021 01 |
| Деталь: | E RING |
| Парткод: | A0EY PP01 00 |
| Деталь: | SCREW |
| Парткод: | A02F PP1K 00 |
| Деталь: | SCREW |
| Парткод: | A02F PP1N 00 |
| Деталь: | BRACKET |
| Парткод: | A02F 1058 00 |
| Деталь: | RAIL |
| Парткод: | 4004 3029 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 1164 3053 12 |
| Деталь: | SPACER |
| Парткод: | A02F 6252 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2099 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3541 01 |
| Деталь: | HOLDER |
| Парткод: | 4004 3062 06 |
| Деталь: | PHOTO INTERUPPTER |
| Парткод: | 9J06 R901 00 |
| Деталь: | ACTUATOR |
| Парткод: | 1164 3027 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4004 3063 01 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 61 |
| Деталь: | ACTUATOR |
| Парткод: | 4004 3061 01 |
| Деталь: | Paperfeed Wiring /1 |
| Парткод: | A02F N100 01 |
| Деталь: | LEVER |
| Парткод: | 1164 3020 03 |
| Деталь: | PWB ASSY |
| Парткод: | 4037 0104 01 |
| Деталь: | HOLDER |
| Парткод: | 1164 3022 02 |
| Деталь: | SPACER |
| Парткод: | 4004 3052 01 |
| Деталь: | CUSHION |
| Парткод: | 4038 2162 02 |
| Деталь: | RAIL |
| Парткод: | A02F 1008 01 |
| Деталь: | PROTECTION |
| Парткод: | 1154 4670 01 |
| Деталь: | OZONE FILTER |
| Парткод: | A02E R727 00 |
| Деталь: | DUCT |
| Парткод: | A02E 1172 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | SEAL |
| Парткод: | A02E 1173 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1175 01 |
| Деталь: | BRACKET |
| Парткод: | A02F 1180 00 |
| Деталь: | SEAL |
| Парткод: | 4038 2062 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0904 01 |
| Деталь: | BRACKET |
| Парткод: | 4004 3011 01 |
| Деталь: | LEVER |
| Парткод: | 4004 3012 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2051 01 |
| Деталь: | SEAL |
| Парткод: | A02E 1179 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J06 2086 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 1055 00 |
| Деталь: | PWB Assembly(PWB-PH ASSY) |
| Парткод: | A02F H003 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 1330 00 |
| Деталь: | PU Lifting Plate Assy |
| Парткод: | A02E R704 00 |
| Деталь: | ROLL |
| Парткод: | 4038 2094 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | 4038 2016 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A02E 1058 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2018 03 |
| Деталь: | BRACKET |
| Парткод: | 4038 2061 01 |
| Деталь: | ATDC Connector Assy |
| Парткод: | A02E R705 00 |
| Деталь: | HOLDER |
| Парткод: | A02F R700 00 |
| Деталь: | Gear 83/115T |
| Парткод: | A02E 2513 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2524 00 |
| Деталь: | Gear 65T |
| Парткод: | A02E 2520 01 |
| Деталь: | GEAR 18/30T |
| Парткод: | 4004 2545 01 |
| Деталь: | GEAR 26T |
| Парткод: | A02F 2529 00 |
| Деталь: | GEAR 32/18T |
| Парткод: | 4038 2531 01 |
| Деталь: | GEAR 32T |
| Парткод: | A02F 2599 00 |
| Деталь: | PIN |
| Парткод: | A02E 2290 00 |
| Деталь: | SHAFT |
| Парткод: | A02F 2535 01 |
| Деталь: | BUSHING |
| Парткод: | 1200 3121 09 |
| Деталь: | GEAR 22T |
| Парткод: | A02E 2519 00 |
| Деталь: | GEAR 18T |
| Парткод: | A02F 2598 00 |
| Деталь: | PIN |
| Парткод: | 4038 2699 01 |
| Деталь: | SHAFT |
| Парткод: | A02F 2515 00 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 02 |
| Деталь: | HOLDER |
| Парткод: | A02F 2526 00 |
| Деталь: | CLUTCH |
| Парткод: | A02F M201 00 |
| Деталь: | GEAR 24T |
| Парткод: | 4038 2532 01 |
| Деталь: | Gear 22/46T |
| Парткод: | A02E 2517 00 |
| Деталь: | Gear 50/56T |
| Парткод: | A02E 2549 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2523 01 |
| Деталь: | Gear 50T |
| Парткод: | A02E 2514 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M203 00 |
| Деталь: | Gear 46/53T |
| Парткод: | A02E 2551 00 |
| Деталь: | Gear 42/56T |
| Парткод: | A02E 2508 00 |
| Деталь: | GEAR 20/56T |
| Парткод: | 4038 2578 01 |
| Деталь: | HOLD PLATE |
| Парткод: | A02F 2539 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 2536 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2275 01 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 2597 00 |
| Деталь: | Feed/Transport Drive Assy |
| Парткод: | A02F R702 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | DUCT |
| Парткод: | A02F 1153 00 |
| Деталь: | PROTECTION |
| Парткод: | 1154 4670 01 |
| Деталь: | COVER |
| Парткод: | A02F 1672 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02F 2647 03 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326 1910 21 |
| Деталь: | I/F Wiring |
| Парткод: | A02F N10U 01 |
| Деталь: | PWB Assembly(PWB-CSRC ASSY) |
| Парткод: | A02F H005 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A02F 2651 00 |
| Деталь: | BRACKET |
| Парткод: | A02F 2650 02 |
| Деталь: | SCREW |
| Парткод: | 4025 2283 01 |
| Деталь: | HIGH VOLTAGE UNIT |
| Парткод: | A02E M402 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 1329 00 |
| Деталь: | IU Contact Assy Black |
| Парткод: | A02F R70G 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2222 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2233 02 |
| Деталь: | HOLDER |
| Парткод: | A02F 1321 00 |
| Деталь: | COVER |
| Парткод: | A02E 1327 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2203 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2225 02 |
| Деталь: | CONTACT |
| Парткод: | A02F 1341 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 1323 01 |
| Деталь: | CONTACT |
| Парткод: | A02F 1342 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2276 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 1324 00 |
| Деталь: | IU Contact Assy CMY |
| Парткод: | A02F R70H 00 |
| Деталь: | SET PLATE |
| Парткод: | 4038 2038 02 |
| Деталь: | RAIL |
| Парткод: | A02E 1019 02 |
| Деталь: | LABEL |
| Парткод: | 4038 7316 01 |
| Деталь: | CLAW |
| Парткод: | A02F 1072 00 |
| Деталь: | CLAW |
| Парткод: | A02F 1074 00 |
| Деталь: | CLAW |
| Парткод: | A02F 1073 00 |
| Деталь: | CLAW |
| Парткод: | A02F 1076 00 |
| Деталь: | COVER |
| Парткод: | A02E 1050 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3662 01 |
| Деталь: | SEAL |
| Парткод: | A02E 3661 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 3660 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2110 03 |
| Деталь: | RAIL |
| Парткод: | A02E 1022 00 |
| Деталь: | Photoconductor Relay harness |
| Парткод: | A02F N10N 00 |
| Деталь: | Fixing Relay harness |
| Парткод: | A02F N105 02 |
| Деталь: | RAIL |
| Парткод: | A02E 1023 01 |
| Деталь: | RAIL |
| Парткод: | A02E 1024 01 |
| Деталь: | Hopper Drive Assy 1 |
| Парткод: | A02E R710 00 |
| Деталь: | Hopper Drive Assy 2 |
| Парткод: | A02E R711 00 |
| Деталь: | Brushless motor /30 |
| Парткод: | A02F M102 00 |
| Деталь: | Brushless motor |
| Парткод: | A02E M103 00 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A02F R70E 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 1106 00 |
| Деталь: | PIN |
| Парткод: | A02E 2290 00 |
| Деталь: | GEAR 36T |
| Парткод: | A02E 2518 00 |
Коды ошибок
C0001
C0204
C0206
C0208
C0209
C0210
C0211
C0212
C0213
C0214
C0215
C0301
C1004
C1182
C11A1
C11E0
C2151
C2152
C2164
C2253
C2254
C225D
C2451
C2551
C2552
C2553
C2554
C2555
C2556
C2557
C2558
C2559
C255A
C255B
C255C
C2650
C2651
C2652
C2653
C2654
C2A01
C2A02
C2A03
C2A04
C3101
C3201
C3202
C3301
C3302
C3421
C3423
C3721
C3723
C3821
C3823
C4151
C4152
C4153
C4154
C4551
C4552
C4553
C4554
C5102
C5103
C5351
C5354
C5357
C6102
C6401
C6704
C6751
CC151
CC155
Описание
| Error code: | C0001 |
| Description: | Main Motor turning at abnormal timing The Main Motor Lock signal remains faulty for a predetermined continuous period of time while the Main Motor remains stationary. |
| Remedy: | 1 Main Motor rotation while it is being energized: the voltage across PJ13I-7A on Master Board and GND remains DC 0 V. YES: Change Master Board. NO: Change motor. |
| Error code: | C0204 |
| Description: | Yellow PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 2 upper limit sensor (PS14) • Tray 2 lift-up motor (M8) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0206 |
| Description: | Black PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 3 upper limit sensor (PS22) • Tray 3 lift-up motor (M23) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0208 |
| Description: | Tray 5 feeder up/down abnormality |
| Causes: | • Tray 4 upper limit sensor (PS27) • Tray 4 lift-up motor (M24) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Error code: | C0209 |
| Description: | LCT elevator motor malfunction |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0211 |
| Description: | Tray 1 feeder up/down abnormality • The paper feed tray 1 lift-up position sensor is not unblocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The paper feed tray 1 lift-up position sensor is not blocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started. |
| Causes: | • Bypass lift-up motor (M26) • Bypass upper limit sensor (PS35) • Bypass lower limit sensor (PS36) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check the connector of M1 for proper drive coupling and correct as necessary. 3 PS17 I/O check PRCB CN6PRCB-7 (ON) D-2. 4 SL1 operation check PRCB CN6PRCB-4 (ON) D-1. 5 M1 operation check PRCB CN34PRCB-10 (REM) PRCB CN34PRCB-13 (LOCK) D-22. 6 Change SL1. 7 Change M1. 8 Change PRCB. |
| Error code: | C0212 |
| Description: | LCT ejection failure |
| Error code: | C0213 |
| Description: | LCT shift gate malfunction |
| Error code: | C0214 |
| Description: | LCT shifting failure |
| Causes: | • Shifter motor (M133) • Shifter stop / lower limit position sensor (PS138) • Shifter home sensor (PS139) • PC control board (PCCB) |
| Error code: | C0215 |
| Description: | LCT shift motor malfunction |
| Error code: | C0301 |
| Description: | Suction fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Suction fan (FM1) • Paper feed/transport drive board (PFTDB) |
| Remedy: | 1 Check the FM8 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM8 operation check PRCB CN3PRCB-2 (ON) PRCB CN3PRCB-3 (LOCK) D-4 to 5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C1004 |
| Description: | FNS communication error |
| Causes: | FS control board (FSCB) |
| Error code: | C1182 |
| Description: | Unsupported option trouble |
| Causes: | When JS-504 is installed: Shift motor (M2) Shift home sensor (PS6) JS control board (JSCB). When FS-527 is installed: Tray2 shift motor (M16) Tray2 shift home sensor (PS25) FS control board (FSCB) |
| Error code: | C11A1 |
| Description: | Finishing option exit roller pressure/retraction failure |
| Causes: | Exit roller retraction motor (M9) Exit roller pressure sensor (PS12) FS control board (FSCB) |
| Error code: | C11E0 |
| Description: | Unsupported option trouble |
| Causes: | When FS-527 is installed: Duplex path switching motor (M2) Duplex path switching sensor (PS3)FS control board (FSCB). When JS-504 is installed: Route change motor (M3) Route change home sensor (PS4) JS control board (JSCB) |
| Error code: | C2151 |
| Description: | Secondary transfer roller pressure welding alienation • During a retraction operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its retracted position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. • During a pressure operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its pressed position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. |
| Causes: | • 2nd transfer pressure motor (M3) • 2nd transfer pressure sensor (PS50) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M11 connector for proper connection and correct as necessary. 2 Check the connector of M11 for proper drive coupling and correct as necessary. 3 PS36 I/O check PRCB CN3PRCB-9 (ON) D-5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C2152 |
| Description: | Transfer belt pressure welding alienation • During a retraction operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its retracted position within a predetermined period of time after the transfer belt retraction clutch is turned ON. • During a pressure operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its pressed position within a predetermined period of time after the transfer belt clutch is turned ON. |
| Causes: | • 1st transfer pressure sensor/K (PS51) • 1st transfer pressure sensor/YMC (PS52) • 1st transfer pressure motor (M21) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 PS31 I/O check PRCB CN36PRCB-15 (ON) D-26 to 27. 3 CL7 operation check PRCB CN39PRCB-10 (ON) D-23. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change CL7. 6 Change M5. 7 Change PRCB. |
| Error code: | C2164 |
| Description: | PC charge malfunction • When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined period of time. |
| Causes: | • Imaging unit • High voltage unit/1 (HV1) • Printer control board (PRCB) |
| Remedy: | 1 Check the imaging unit for proper connection and correct as necessary. 2 Check the HV connector for proper connection and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Change IU. 5 Change HV. 6 Change PRCB. |
| Error code: | C2253 |
| Description: | Color PC motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/YMC (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2254 |
| Description: | Color PC motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/YMC motor (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C225D |
| Description: | Color dev. unit engagement/disengagement failure • The gears remain disengaged after the lapse of a predetermined period of time after the engagement operation is started by the color dev. unit engaged motor. • The gears remain engaged after the lapse of a predetermined period of time after the disengagement operation is started by the color dev. unit engaged motor. |
| Remedy: | 1 Check the M10 connector for proper connection and correct as necessary. 2 Check the M10 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 PS26 I/O check PRCB CN39PRCB-18 (ON) D-24. 5 M10 operation check PRCB CN39PRCB-12 (REM) D-24. 6 Change M10. 7 Change PRCB. |
| Error code: | C2451 |
| Description: | Release new transfer belt unit • A new installation is not detected when a new transfer cleaner unit (image transfer belt unit) is installed. |
| Remedy: | 1 Reinstall unit. 2 Check there is a short circuit in the fuse of the transfer belt unit. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Change PRCB. |
| Error code: | C2551 |
| Description: | Abnormally low toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2552 |
| Description: | Abnormally high toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2553 |
| Description: | Abnormally low toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2554 |
| Description: | Abnormally high toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2555 |
| Description: | Abnormally low toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2556 |
| Description: | Abnormally high toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2557 |
| Description: | Abnormally low toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Developing unit • Toner cartridge • Toner empty sensor/K (PZS/K) • Toner supply motor/K (M12) • Toner cartridge motor/CK (M14) • MFP board (MFPB) |
| Remedy: | 1 M3 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 D-23. 2 Reinstall imaging unit. 3 Reinstall toner cartridge. 4 Change imaging unit /K. 5 Change PRCB. |
| Error code: | C2558 |
| Description: | Abnormally high toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Developing unit • Toner cartridge • Sub hopper unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit /K. 4 Change PRCB. |
| Error code: | C2559 |
| Description: | Cyan TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255A |
| Description: | Magenta TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255B |
| Description: | Yellow TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255C |
| Description: | Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit /K. 2 Change imaging unit /K. 3 Change PRCB. |
| Error code: | C2650 |
| Description: | PF feed motor error (Side Multi Feeder) Object: Side multi feeder |
| Causes: | The ready signal is not at the L level (stable rotation) for passing 2s since the PF feed motor drive is started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected. The drive parts are faulty. Execute U247 [SMT] > [Motor On] to check the paper feeding operation. If the PF feed motor does not properly operate, reconnect the connector. Check if the PF feed roller and the drive gears rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. Executing U247 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF main PWB • PF main PWB - Engine PWB (Cable from the side multi feeder) Wiring diagram 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF drive unit (Side multi feeder) 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 5 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2651 |
| Description: | EEPROM access error (IU C) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2652 |
| Description: | EEPROM access error (IU M) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2653 |
| Description: | EEPROM access error (IU Y) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2654 |
| Description: | EEPROM access error (IU K) |
| Causes: | Imaging unit /C Imaging unit /M Imaging unit /Y Drum unit /K Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2A01 |
| Description: | EEPROM access error (TC C) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C2A02 |
| Description: | EEPROM access error (TC M) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C2A03 |
| Description: | EEPROM access error (TC Y) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C2A04 |
| Description: | EEPROM access error (TC K) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C3101 |
| Description: | Fusing roller separation failure • With the fusing roller being retracted, the pulse of the fusing roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • With the fusing roller being pressed, the pulse of the roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • During a pressure operation of the fusing roller, the fusing roller is not at the pressed position even after the roller retraction sensor counts the specified number of pulses after the fusing retraction motor starts rotating. |
| Causes: | • Fusing pressure home sensor (PS55) • Fusing pressure motor (M29) • Printer control board (PRCB) • Fusing unit |
| Remedy: | 1 Check the M12 connector for proper connection and correct as necessary. 2 PS38 I/O check PRCB CN28PRCB-8 (ON) D-25. 3 M12 operation check PRCB CN28PRCB-4 to 5 D-25. 4 Change M12. 5 Change fusing unit. 6 Change PRCB. |
| Error code: | C3201 |
| Description: | Fusing motor failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3202 |
| Description: | Fusing motor turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3301 |
| Description: | Fusing cooling fan motor/ 1 failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Remedy: | 1 Check the FM9 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM9 operation check PRCB CN40PRCB-2 (ON) PRCB CN40PRCB-3 (LOCK) D-19. 4 Change FM9. 5 Change PRCB. |
| Error code: | C3302 |
| Description: | Fusing cooling fan motor/ 2,3 failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Paper cooling fan (FM8) • Printer control board (PRCB) |
| Remedy: | 1 Check the FM10 or FM11 connector for proper connection and correct as necessary 2 Check the fan for possible overload and correct as necessary. 3 FM10/FM11 operation check PRCB CN40PRCB-5 (ON) PRCB CN40PRCB-6 (LOCK) D-19. PRCB CN40PRCB-8 (ON) PRCB CN40PRCB-9 (LOCK) D-18. 4 Change FM10/FM11. 5 Change PRCB. |
| Error code: | C3421 |
| Description: | Fusing heaters trouble (heating side) • The temperature detected by the heating roller thermistor/C does not reach a predetermined level after the lapse of a predetermined period of time after the heating roller fusing heater lamp lights up. • The difference between the maximum and minimum temperatures detected by the heating roller thermistor/C within a predetermined period of time after the start of a warm-up cycle is below or above a predetermined value. • The temperature detected after a pressure level correction remains under a predetermined level even after the lapse of a predetermined period of time after the start of the temperature detection. • During a warm-up, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. |
| Causes: | • Fusing unit • C3421: Fusing temperature sensor/1 (TEM1: center) • C3426: Fusing temperature sensor/1 (TEM1: edge) • DC power supply (DCPS) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3423 |
| Description: | Fusing heaters trouble (pressurizing side) • After warm-up operation starts, the fusing pressure roller thermistor does not detect a temperature as high as a predetermined one though a predetermined period of time has elapsed. • The temperature of the pressure roller remains lower than a predetermined level even after the lapse of a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3721 |
| Description: | Fusing abnormally high temperature detection (heating side) • The heating roller thermistor continues to detect a temperature higher than a predetermined one for a predetermined period of time. • Hard protection signal L is detected continuously over a predetermined period of time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3723 |
| Description: | Fusing abnormally high temperature detection (pressurizing side) • The temperature of the pressure roller continues to be higher than a predetermined level for a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • Pressure roller power supply unit (PRPU) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3821 |
| Description: | Fusing abnormally low temperature detection (heating side) • The heating roller thermistor continues to detect a temperature lower than a predetermined one for a predetermined period of time. • In the states other than a warm-up operation, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. • The power supply frequency cannot be detected. |
| Causes: | • Fusing unit • C3821: Thermistor/1 (TH1) • C3822: Thermistor/2 (TH2) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3823 |
| Description: | Fusing abnormally low temperature detection (pressurizing side) • The temperature of the pressure roller continues to be lower than a predetermined level for a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • Pressure roller power supply unit (PRPU) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C4151 |
| Description: | Polygon motor rotation trouble (C) • The polygon motor fails to turn stably even after the lapse of a given period of time after activating the polygon motor. • Motor lock signal detects HIGH for a given period time consecutively during the polygon motor is rotating. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4152 |
| Description: | Polygon motor rotation trouble (M) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4153 |
| Description: | Polygon motor rotation trouble (Y) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4154 |
| Description: | Polygon motor rotation trouble (K) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4551 |
| Description: | Laser malfunction (C) • SOS signal is not detected even after the lapse of a given period of time after staring the laser output. • SOS signal is not detected for a given period of time during printing or image stabilization adjustment. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4552 |
| Description: | Laser malfunction (M) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4553 |
| Description: | Laser malfunction (Y) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4554 |
| Description: | Laser malfunction (K) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C5102 |
| Description: | Main high-voltage error C |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5103 |
| Description: | Main high-voltage error M |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5351 |
| Description: | Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • DC power supply cooling fan (FM9) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1 Check the FM5 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check PRCB CN30PRCB-11 (ON) PRCB CN30PRCB-12 (LOCK) K-8. 4 Change FM5. 5 Change DCPU. 6 Change PRCB. |
| Error code: | C5354 |
| Description: | Exhaust fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Ozone ventilation fan (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM4 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM4 operation check PRCB CN3PRCB-14 (ON) PRCB CN3PRCB-16 (LOCK) D-6. 4 Change FM4. 5 Change PRCB. |
| Error code: | C5357 |
| Description: | Cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Machine cooling fan (FM1) • CPU board (CPUB) • Base board (BASEB) |
| Remedy: | 1 Check the FM1 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM1 operation check PRCB CN30PRCB-4 (ON) PRCB CN30PRCB-6 (LOCK) K-7. 4 Change FM1. 5 Change PRCB. |
| Error code: | C6102 |
| Description: | Drive system home sensor malfunction • The scanner home sensor (PS201) is unable to detect the scanner located at its home position. • The scanner home sensor (PS201) is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor (PS201) detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor (PS201). |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6401 |
| Description: | Other troubles of scanner • The scan operation was terminated abnormally because of a reason except defined trouble. |
| Remedy: | 1 Check the connectors between BCRUB and MFBUB for proper connection and correct as necessary. 2 Change BCRUB. 3 Change MFBUB. 4 Change exposure unitk. |
| Error code: | C6704 |
| Description: | Image input time out. Image data is not input from the scanner to the MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Memory Bus Check] -> [Scanner -> Memory], and conduct the memory bus function. 2. Correct the harness connection between scanner section and MFPB if faulty. 3. MFPB F3E conduction check 4. Replace MFPB. 5. Replace the CCD unit. |
| Error code: | C6751 |
| Description: | CCD gain adjustment failure. • The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment. |
| Causes: | • LED exposure unit • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 2. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 3. Correct the harness connection between SCDB CN1-DCPU CN005 if faulty. 4. Check for possible extraneous light and correct as necessary. 5. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 6. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 7. Replace SCDB 8. Replace the CCD unit. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | CC151 |
| Description: | ROM contents error upon startup (MSC) • A fault is detected in a sequence of ROM contents check of the MSC (PRCB) during starting |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. |
| Error code: | CC155 |
| Description: | Finisher ROM error |
| Causes: | FS control board (FSCB) |
