Konica-Minolta bizhub C250P
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
40000
Скорость печати
A4
25
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Область применения |
малый офис |
Макс. формат |
A3 |
Число страниц в месяц |
40 000 |
Сканер |
|
Телефон |
|
Копир |
|
Печать фотографий |
|
Факс |
|
Цветность печати |
цветная |
Тип устройства |
Принтер |
Принтер |
|
Прямая печать |
|
Двусторонняя печать |
|
Пигментные чернила |
|
Печать без полей |
|
Количество цветов |
4 |
Макс, разрешение для ч/б печати |
|
| По X | 600 |
| По Y | 1 800 |
Скорость ч/б печати |
|
| A4 | 25 |
Сканер |
|
Отправка изображения по e-mail |
|
Стандарт WIA |
|
Стандарт TWAIN |
|
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
12 000 |
Ресурс цветного картриджа/тонера |
12 000 |
Печать на: |
|
| CD/DVD |
|
| Фотобумаге |
|
| Рулоне |
|
| Конвертах |
|
| Этикетках |
|
| Пленках |
|
| Матовой бумаге |
|
| Глянцевой бумаге |
|
Факс |
|
Цветной |
|
Телефон |
|
Спикерфон |
|
Стандарт DECT |
|
АОН |
|
Автоответчик |
|
Caller ID |
|
Беспроводная трубка |
|
Проводная трубка |
|
Языки управления |
|
| PostScript 2 |
|
| PostScript |
|
| PostScript 3 |
|
Лотки |
|
Подача бумаги |
|
| Стандартная | 850 |
Вывод бумаги |
|
| Стандартный | 1 250 |
Финишер |
|
Сортировка со сдвигом |
|
Брошюровщик |
|
Степлер |
|
Сортер |
|
Интерфейсы |
|
RS-232 |
|
Wi-Fi |
|
Bluetooth |
|
LPT |
|
Инфракрасный порт |
|
USB |
|
Устройство для чтения карт памяти |
|
FireWire (IEEE 1394) |
|
Ethernet (RJ-45) |
|
Память/Процессор |
|
Объем памяти |
1 024 |
Дополнительная информация |
|
Мин. системные требования |
Intel Pentium II |
Поддержка ОС |
|
| Linux |
|
| DOS |
|
| Mac OS |
|
| Windows |
|
Габариты |
|
Вес |
76 |
Высота |
601 |
Ширина |
653 |
Глубина |
712 |
Модули
Fusing Drive Section
P-H FRAME SECTION 2
MPT CASSETTE TRAY SECTION
TRANSPORT DRIVE SECTION
MANUAL FEED SECTION 2
ELECTRICAL COMPONENTS
2ND CASSETTE PAPER TAKE-UP SECTION 2
PAPER EXIT SECTION
MAIN FRAME
TRANSFER SECTION
2ND CASSETTE FRAME
RIGHT DOOR SECTION
MPT PAPER TAKE-UP SECTION
FUSING SECTION
P-H FRAME SECTION
ERASER SECTION
MPT CASSETTE PAPER TAKE-UP SECTION
2ND CASSETTE
EXTERNAL PARTS
INNER COVER SECTION
WASTE TONER BOX SECTION
REAR DUCT SECTION
2ND CASSETTE PAPER TAKE-UP SECTION
2ND CASSETTE DRIVE SECTION
MANUAL FEED SECTION 3
HOPPER DRIVE SECTION
DEVELOPMENT DRIVE SECTION
T-C RAIL SECTION
MANUAL FEED SECTION
2ND CASSETTE PAPER TAKE-UP SECTION 3
TRANSFER BELT SECTION
2ND CASSETTE 2
PAPER EXIT DRIVE SECTION
CONTACT SECTION
WASTE TONER TRANSPORT SECTION
PAPER TRANSPORT SECTION
Детали HOPPER DRIVE SECTION
| Деталь: | BRACKET |
| Парткод: | 4038 2556 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2592 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2591 01 |
| Деталь: | GEAR 37T |
| Парткод: | 4038 2540 01 |
| Деталь: | GEAR 81/17T |
| Парткод: | 4038 2538 01 |
| Деталь: | SCREW |
| Парткод: | 4154 3804 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2557 01 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2573 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2596 01 |
| Деталь: | GEAR 2DT |
| Парткод: | 4038 2574 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2576 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2577 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2588 01 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2580 01 |
| Деталь: | GEAR 22T |
| Парткод: | 4038 2575 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2600 02 |
| Деталь: | SHAFT |
| Парткод: | 4038 2587 01 |
| Деталь: | GEAR 20T |
| Парткод: | 4038 2541 01 |
| Деталь: | CLUTCH |
| Парткод: | 9322 1300 21 |
| Деталь: | GEAR 41T |
| Парткод: | 4038 2593 02 |
| Деталь: | CONNECTOR 2P |
| Парткод: | 9383 2210 11 |
| Деталь: | MOTOR |
| Парткод: | 9314 1400 71 |
| Деталь: | BRACKET |
| Парткод: | 4038 2096 03 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 1906 03 |
| Деталь: | GEAR 27T |
| Парткод: | 4038 2189 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 2187 04 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2044 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2194 01 |
| Деталь: | SCREW |
| Парткод: | 4106 2063 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2193 03 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2196 01 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2191 02 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2190 03 |
| Деталь: | SHAFT |
| Парткод: | 4038 2192 02 |
| Деталь: | BRACKET ASSY |
| Парткод: | 4038 0211 04 |
| Деталь: | GEAR 3DT |
| Парткод: | 4038 2188 02 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 2184 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2095 03 |
| Деталь: | WASHER |
| Парткод: | 4038 2179 01 |
| Деталь: | SPRING |
| Парткод: | 4038 2042 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2043 03 |
| Деталь: | CONTACT |
| Парткод: | 4038 2180 01 |
| Деталь: | SKEW ADJUSTMENT ASSY |
| Парткод: | 4038 0758 00 |
| Деталь: | PRINT HEAD UNIT |
| Парткод: | 4038 0778 00 |
| Деталь: | LIFTING PLATE |
| Парткод: | 4036 3022 01 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4687 3281 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4134 3106 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4036 3008 01 |
| Деталь: | LABEL MP CD |
| Парткод: | 4036 7314 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4011 3011 01 |
| Деталь: | LEVER |
| Парткод: | 4037 3210 01 |
| Деталь: | GUIDE |
| Парткод: | 4004 3040 02 |
| Деталь: | GUIDE |
| Парткод: | 4004 3024 01 |
| Деталь: | LEVER |
| Парткод: | 1164 3061 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1164 3062 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4004 3033 01 |
| Деталь: | GUIDE |
| Парткод: | 4004 3038 01 |
| Деталь: | SEAL |
| Парткод: | 4004 3008 01 |
| Деталь: | LABEL |
| Парткод: | 4037 7306 12 |
| Деталь: | CASSETTE |
| Парткод: | 4036 3021 02 |
| Деталь: | COVER |
| Парткод: | 4038 3071 02 |
| Деталь: | LABEL NUMBER |
| Парткод: | 4038 7312 01 |
| Деталь: | HANDLE |
| Парткод: | 4036 3025 01 |
| Деталь: | FRONT COVER |
| Парткод: | 4038 3020 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LEVER |
| Парткод: | 4004 3051 02 |
| Деталь: | BRACKET |
| Парткод: | 4004 3031 01 |
| Деталь: | SPACER |
| Парткод: | 4037 3226 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4037 3223 01 |
| Деталь: | RACK |
| Парткод: | 4004 3032 01 |
| Деталь: | GUIDE |
| Парткод: | 4021 3036 01 |
| Деталь: | GUIDE |
| Парткод: | 4004 3042 01 |
| Деталь: | GEAR 2DT |
| Парткод: | 1164 3045 01 |
| Деталь: | LABEL MP FD |
| Парткод: | 4036 7313 01 |
| Деталь: | RAIL |
| Парткод: | 4004 3030 01 |
| Деталь: | SPACER |
| Парткод: | 4037 3227 01 |
| Деталь: | LABEL CAPACITY |
| Парткод: | 4004 7324 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4036 3028 01 |
| Деталь: | MULTIPURPOSE CASSETTE |
| Парткод: | 4038 0762 00 |
| Деталь: | Gear 83/115T |
| Парткод: | 4038 2513 01 |
| Деталь: | Gear 65T |
| Парткод: | 4038 2520 01 |
| Деталь: | GEAR 26T |
| Парткод: | 4038 2529 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4038 2599 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2524 01 |
| Деталь: | GEAR 32/18T |
| Парткод: | 4038 2531 01 |
| Деталь: | GEAR 24T |
| Парткод: | 4038 2532 01 |
| Деталь: | CLUTCH |
| Парткод: | 9322 1400 21 |
| Деталь: | GEAR 49/44T |
| Парткод: | 4038 2551 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2526 01 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 01 |
| Деталь: | GEAR 22T |
| Парткод: | 4038 2519 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2535 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2598 01 |
| Деталь: | PIN |
| Парткод: | 4038 2699 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2515 01 |
| Деталь: | GEAR 5DT |
| Парткод: | 4038 2514 01 |
| Деталь: | GEAR 37/5DT |
| Парткод: | 4038 2549 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2523 01 |
| Деталь: | CLUTCH |
| Парткод: | 9322 1300 31 |
| Деталь: | GEAR 22/38T |
| Парткод: | 4038 2517 01 |
| Деталь: | GEAR 55/31T |
| Парткод: | 4038 2508 01 |
| Деталь: | GEAR 2D/56T |
| Парткод: | 4038 2578 01 |
| Деталь: | GEAR 18/3DT |
| Парткод: | 4004 2545 01 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 2539 01 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 2536 01 |
| Деталь: | SHIELD |
| Парткод: | 4038 2253 01 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 2597 01 |
| Деталь: | COVER |
| Парткод: | 4038 3205 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 3207 03 |
| Деталь: | FRAME |
| Парткод: | 4038 3208 02 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 3217 01 |
| Деталь: | LEVER |
| Парткод: | 4038 3216 03 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 3220 01 |
| Деталь: | LEVER |
| Парткод: | 4038 3218 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3228 03 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 3263 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3403 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4030 3402 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3268 02 |
| Деталь: | GUIDE |
| Парткод: | 4038 3204 04 |
| Деталь: | RESISTOR |
| Парткод: | 9455 8076 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 3266 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 3261 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 3262 03 |
| Деталь: | GUIDE |
| Парткод: | 4038 3270 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 3265 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3475 01 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | 4034 0151 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3267 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3269 02 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 3281 01 |
| Деталь: | FRAME ASSY |
| Парткод: | 4038 0251 03 |
| Деталь: | RING |
| Парткод: | 1031 4403 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3231 02 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4038 0765 00 |
| Деталь: | BRACKET |
| Парткод: | 4038 2303 02 |
| Деталь: | SCREW |
| Парткод: | 4025 2287 01 |
| Деталь: | ELECTRICALLY CONDUCTIVE MATERIAL |
| Парткод: | 4037 6776 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4581 2269 02 |
| Деталь: | COVER |
| Парткод: | 4037 2242 01 |
| Деталь: | COVER |
| Парткод: | 4037 2247 01 |
| Деталь: | ELECTRICALLY CONDUCTIVE MATERIAL |
| Парткод: | 4037 6778 02 |
| Деталь: | ELECTRICALLY CONDUCTIVE MATERIAL |
| Парткод: | 4037 6777 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4037 2220 02 |
| Деталь: | BRACKET |
| Парткод: | 4037 2219 02 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 1502 03 |
| Деталь: | COVER |
| Парткод: | 4038 2315 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2074 05 |
| Деталь: | CAP |
| Парткод: | 4038 2036 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2075 02 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2073 01 |
| Деталь: | DUCT |
| Парткод: | 4038 2405 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4037 6812 01 |
| Деталь: | SHIELD BOX |
| Парткод: | 4038 2301 04 |
| Деталь: | GUIDE |
| Парткод: | 4004 2203 01 |
| Деталь: | HARD DISK DRIVE |
| Парткод: | 4037 6095 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4036 6870 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2312 01 |
| Деталь: | BUSHING |
| Парткод: | 4025 2294 01 |
| Деталь: | COLLAR |
| Парткод: | 4025 2295 01 |
| Деталь: | WASHER |
| Парткод: | 1200 1442 04 |
| Деталь: | D FILED |
| Парткод: | 4037 6076 01 |
| Деталь: | PWB-SIF |
| Парткод: | 4038 0123 03 |
| Деталь: | DUCT |
| Парткод: | 4038 2404 03 |
| Деталь: | PWB-MFP |
| Парткод: | 4038 0121 06 |
| Деталь: | LID |
| Парткод: | 4038 2302 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 1510 01 |
| Деталь: | COVER |
| Парткод: | 4037 2244 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1300 41 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | DUCT |
| Парткод: | 4038 2410 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3105 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3124 03 |
| Деталь: | BRACKET |
| Парткод: | 4030 3129 03 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3125 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4030 3037 01 |
| Деталь: | BRACKET |
| Парткод: | 4030 3025 02 |
| Деталь: | STAY |
| Парткод: | 4036 3846 02 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4036 3838 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3077 01 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | 4030 0151 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3078 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3079 01 |
| Деталь: | HOLDER |
| Парткод: | 4030 3013 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3017 02 |
| Деталь: | BRACKET |
| Парткод: | 4030 3014 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | COVER |
| Парткод: | 4038 5881 05 |
| Деталь: | LABEL EXIT COVER |
| Парткод: | 4038 7304 01 |
| Деталь: | Neutralizing Brush |
| Парткод: | 4038 5856 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 5886 03 |
| Деталь: | GUIDE |
| Парткод: | 4038 5883 03 |
| Деталь: | LEVER |
| Парткод: | 4038 5894 03 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 5896 02 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LEVER |
| Парткод: | 4038 5895 03 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6835 01 |
| Деталь: | CONNECTOR 3P |
| Парткод: | 9383 2210 41 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1300 41 |
| Деталь: | COVER |
| Парткод: | 4038 5852 02 |
| Деталь: | FRAME |
| Парткод: | 4038 2006 04 |
| Деталь: | BASE FRAME |
| Парткод: | 4038 2090 02 |
| Деталь: | SPACER |
| Парткод: | 4038 3595 01 |
| Деталь: | SWITCH |
| Парткод: | 9332 1710 41 |
| Деталь: | BRACKET |
| Парткод: | 4038 2065 04 |
| Деталь: | COVER |
| Парткод: | 4128 2215 01 |
| Деталь: | COVER |
| Парткод: | 4038 2066 01 |
| Деталь: | SCREW |
| Парткод: | 4154 3804 01 |
| Деталь: | CAP |
| Парткод: | 4038 2036 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2073 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6809 03 |
| Деталь: | BASE FRAME |
| Парткод: | 4038 2004 06 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996 3055 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2097 02 |
| Деталь: | PROTECTION |
| Парткод: | 1154 4670 01 |
| Деталь: | BASE FRAME |
| Парткод: | 4038 2003 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2285 02 |
| Деталь: | SEAL |
| Парткод: | 4038 3548 01 |
| Деталь: | SEAL |
| Парткод: | 4038 3549 01 |
| Деталь: | DUCT |
| Парткод: | 4038 3546 02 |
| Деталь: | DUCT |
| Парткод: | 4038 3547 01 |
| Деталь: | GEAR 34T |
| Парткод: | 4038 3580 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | HOLDER |
| Парткод: | 4038 3557 04 |
| Деталь: | CAM |
| Парткод: | 4038 3553 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 4611 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LEVER |
| Парткод: | 4038 3551 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 3542 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 4620 01 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4038 0776 00 |
| Деталь: | LEVER |
| Парткод: | 4038 3552 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3564 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4038 3563 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 3572 01 |
| Деталь: | GEAR 17/39T |
| Парткод: | 4038 3586 01 |
| Деталь: | Gear 39T |
| Парткод: | 4038 3582 01 |
| Деталь: | GEAR 17/39T |
| Парткод: | 4038 3583 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 3588 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 3566 01 |
| Деталь: | RESISTOR |
| Парткод: | 9455 8076 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 3569 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 3565 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 3568 02 |
| Деталь: | MOTOR ASSY |
| Парткод: | 4038 0774 00 |
| Деталь: | SCREW |
| Парткод: | 4002 2581 01 |
| Деталь: | PLATE ASSY |
| Парткод: | 4067 0202 03 |
| Деталь: | COVER |
| Парткод: | 4067 3803 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4067 3818 02 |
| Деталь: | STAY |
| Парткод: | 4036 3810 03 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4036 3849 01 |
| Деталь: | BRACKET |
| Парткод: | 4348 2042 01 |
| Деталь: | PLATE ASSY |
| Парткод: | 4067 0201 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4067 3821 01 |
| Деталь: | STAY |
| Парткод: | 4036 3808 03 |
| Деталь: | COVER |
| Парткод: | 4067 3802 01 |
| Деталь: | HOLDER |
| Парткод: | 4348 2037 02 |
| Деталь: | BRACKET |
| Парткод: | 4348 2038 02 |
| Деталь: | BRACKET |
| Парткод: | 4036 3843 02 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996 3055 01 |
| Деталь: | BASE FRAME |
| Парткод: | 4036 3814 01 |
| Деталь: | STOP PLATE |
| Парткод: | 4658 3140 02 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4658 3042 01 |
| Деталь: | BRACKET |
| Парткод: | 4036 3828 01 |
| Деталь: | GUIDE |
| Парткод: | 4348 2044 01 |
| Деталь: | BRACKET |
| Парткод: | 4348 2041 02 |
| Деталь: | STAY |
| Парткод: | 4067 3807 02 |
| Деталь: | LEFT COVER |
| Парткод: | 4067 3805 02 |
| Деталь: | RUBBER FOOT |
| Парткод: | 4030 2080 01 |
| Деталь: | STAY |
| Парткод: | 4036 3809 01 |
| Деталь: | BRACKET |
| Парткод: | 4036 3811 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4067 3871 01 |
| Деталь: | REAR COVER LEFT |
| Парткод: | 4067 3856 02 |
| Деталь: | COVER |
| Парткод: | 4067 3857 02 |
| Деталь: | REAR COVER RIGHT |
| Парткод: | 4067 3855 02 |
| Деталь: | SPACER |
| Парткод: | 4348 2040 01 |
| Деталь: | COVER |
| Парткод: | 4038 3515 02 |
| Деталь: | RIGHT DOOR |
| Парткод: | 4038 3506 08 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3520 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3518 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 3516 01 |
| Деталь: | PAWL |
| Парткод: | 4038 3508 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3591 01 |
| Деталь: | DUCT |
| Парткод: | 4038 3545 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3519 02 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3512 01 |
| Деталь: | COLLAR |
| Парткод: | 4038 3534 01 |
| Деталь: | BRACKET ASSY |
| Парткод: | 4038 0210 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 3511 02 |
| Деталь: | STOPPER |
| Парткод: | 4038 3523 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 3571 02 |
| Деталь: | PAWL |
| Парткод: | 4038 3507 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 3505 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3522 01 |
| Деталь: | COVER |
| Парткод: | 4038 3521 01 |
| Деталь: | Label JAM |
| Парткод: | 4038 7302 01 |
| Деталь: | DOOR ASSY |
| Парткод: | 4038 0752 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3541 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6829 01 |
| Деталь: | HOLDER |
| Парткод: | 4004 3062 06 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4038 0902 01 |
| Деталь: | ACTUATOR |
| Парткод: | 1164 3027 01 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 61 |
| Деталь: | ACTUATOR |
| Парткод: | 4004 3061 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4004 3063 01 |
| Деталь: | CUSHION |
| Парткод: | 4038 2162 01 |
| Деталь: | RAIL |
| Парткод: | 4038 2008 02 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2408 01 |
| Деталь: | HOLDER |
| Парткод: | 1164 3022 02 |
| Деталь: | PWB-I |
| Парткод: | 4037 0104 01 |
| Деталь: | LEVER |
| Парткод: | 1164 3020 03 |
| Деталь: | SPACER |
| Парткод: | 4004 3052 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 1164 3054 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0904 01 |
| Деталь: | BRACKET |
| Парткод: | 4004 3011 01 |
| Деталь: | LEVER |
| Парткод: | 4004 3012 01 |
| Деталь: | SIZE DETECTING PWB ASSY |
| Парткод: | 4038 0772 00 |
| Деталь: | FUSING UNIT 100-127V |
| Парткод: | 4038 0754 00 |
| Деталь: | FUSING UNIT 220-240V |
| Парткод: | 4038 0755 00 |
| Деталь: | Fusing Unit 100V |
| Парткод: | 4038 0753 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2082 03 |
| Деталь: | BRACKET |
| Парткод: | 4038 3735 01 |
| Деталь: | LABEL JAM LEVER |
| Парткод: | 4038 7319 02 |
| Деталь: | PWB-D |
| Парткод: | 4038 0105 03 |
| Деталь: | ROLL |
| Парткод: | 4038 2094 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | 4038 2016 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2017 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2018 03 |
| Деталь: | SCREW |
| Парткод: | 4154 3804 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2061 01 |
| Деталь: | CONNECTOR ASSY |
| Парткод: | 4038 0766 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2249 02 |
| Деталь: | HOLDER |
| Парткод: | 4038 2060 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2067 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2051 01 |
| Деталь: | COLLAR |
| Парткод: | 4038 2086 01 |
| Деталь: | SHIELD PLATE |
| Парткод: | 4038 2199 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2182 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2181 01 |
| Деталь: | LED PILOT LAMP |
| Парткод: | 9353 2400 11 |
| Деталь: | BRACKET |
| Парткод: | 4038 2015 02 |
| Деталь: | RAIL |
| Парткод: | 4038 2014 07 |
| Деталь: | LABEL |
| Парткод: | 4038 7309 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2011 03 |
| Деталь: | SLIDER |
| Парткод: | 4038 2069 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2072 03 |
| Деталь: | SHIELD PLATE |
| Парткод: | 4038 2198 02 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2040 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2056 02 |
| Деталь: | DUC |
| Парткод: | 4038 2052 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2053 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2081 02 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2091 03 |
| Деталь: | BRACKET |
| Парткод: | 4038 2012 03 |
| Деталь: | SEAL |
| Парткод: | 4038 2151 02 |
| Деталь: | PIPE |
| Парткод: | 4038 2106 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2104 02 |
| Деталь: | SHUTTER |
| Парткод: | 4038 2103 04 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2105 03 |
| Деталь: | SEAL |
| Парткод: | 4038 2102 01 |
| Деталь: | PIPE |
| Парткод: | 4038 2101 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2183 01 |
| Деталь: | WEIGHT |
| Парткод: | 4038 3063 01 |
| Деталь: | WASHER |
| Парткод: | 4036 3030 01 |
| Деталь: | WASHER |
| Парткод: | 4036 3031 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3020 01 |
| Деталь: | WASHER |
| Парткод: | 1164 3066 01 |
| Деталь: | SHAFT |
| Парткод: | 4004 3001 02 |
| Деталь: | ROLLER |
| Парткод: | 4034 3012 01 |
| Деталь: | COLLAR |
| Парткод: | 4004 3005 01 |
| Деталь: | STOP RING |
| Парткод: | 4658 3046 01 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | 4034 0151 01 |
| Деталь: | GUIDE |
| Парткод: | 4658 3035 02 |
| Деталь: | HOLDER |
| Парткод: | 4004 3003 02 |
| Деталь: | SHAFT |
| Парткод: | 4658 3040 01 |
| Деталь: | COLLAR |
| Парткод: | 4658 3047 01 |
| Деталь: | BRACKET |
| Парткод: | 4004 3004 01 |
| Деталь: | HOLDER |
| Парткод: | 1144 3097 03 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4004 3006 03 |
| Деталь: | BUSHING |
| Парткод: | 1164 3003 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4036 3040 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4036 3018 01 |
| Деталь: | PIN |
| Парткод: | 4036 3014 01 |
| Деталь: | PAWL |
| Парткод: | 1164 3004 03 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1164 3005 02 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4038 0773 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4030 3229 02 |
| Деталь: | FRONT COVER |
| Парткод: | 4067 3852 01 |
| Деталь: | LABEL NUMBER |
| Парткод: | 4038 7321 01 |
| Деталь: | LABEL |
| Парткод: | 4348 7301 02 |
| Деталь: | HANDLE |
| Парткод: | 4036 3025 01 |
| Деталь: | Label Paper supply |
| Парткод: | 4030 7304 02 |
| Деталь: | LIFTING PLATE |
| Парткод: | 4030 3203 01 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030 3226 01 |
| Деталь: | STOPPER |
| Парткод: | 4498 3469 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4030 3223 02 |
| Деталь: | GUIDE |
| Парткод: | 4030 3222 03 |
| Деталь: | CASSETTE ASSY |
| Парткод: | 4038 0155 03 |
| Деталь: | TRAY TOP |
| Парткод: | 4038 1020 03 |
| Деталь: | TOP COVER LIGHT |
| Парткод: | 4038 1039 02 |
| Деталь: | RIGHT COVER |
| Парткод: | 4038 1008 03 |
| Деталь: | LABEL REMOVE |
| Парткод: | 4038 7301 03 |
| Деталь: | HINGE |
| Парткод: | 4038 1010 01 |
| Деталь: | SHAFT |
| Парткод: | 1136 1019 01 |
| Деталь: | CLEANING PA0 |
| Парткод: | 4038 2084 03 |
| Деталь: | SET PLATE |
| Парткод: | 1053 3103 01 |
| Деталь: | BAN0 |
| Парткод: | 4643 1020 02 |
| Деталь: | SEAL |
| Парткод: | 4025 1018 01 |
| Деталь: | SCREW |
| Парткод: | 4038 1049 01 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475 2603 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 1046 01 |
| Деталь: | FRONT 0OOR |
| Парткод: | 4038 1022 05 |
| Деталь: | LABEL bizhub C250P |
| Парткод: | 4038 7327 01 |
| Деталь: | LABEL LOGO MARK |
| Парткод: | 4030 7500 01 |
| Деталь: | LABEL CH CLEAN |
| Парткод: | 4038 7315 02 |
| Деталь: | CLANING MATERIAL |
| Парткод: | 4038 2083 01 |
| Деталь: | TOP COVER |
| Парткод: | 4038 1021 05 |
| Деталь: | LEFT COVER UPPER |
| Парткод: | 4038 1054 04 |
| Деталь: | LABEL HI0E |
| Парткод: | 4036 1011 01 |
| Деталь: | REAR COVER |
| Парткод: | 4038 1035 01 |
| Деталь: | LEFT COVER REAR |
| Парткод: | 4038 1027 03 |
| Деталь: | LABEL EARTH CAUTION |
| Парткод: | 4037 7406 01 |
| Деталь: | LABEL OUTLET |
| Парткод: | 4038 7341 01 |
| Деталь: | COVER |
| Парткод: | 4037 1006 01 |
| Деталь: | REAR COVER |
| Парткод: | 4038 1023 04 |
| Деталь: | RIGHT COVER REAR |
| Парткод: | 4038 1029 04 |
| Деталь: | REAR COVER |
| Парткод: | 4038 1031 03 |
| Деталь: | PLATE NUT |
| Парткод: | 4036 4909 01 |
| Деталь: | CONTROL PANEL ASSY |
| Парткод: | 4038 6055 02 |
| Деталь: | CONTROL PANEL ASSY |
| Парткод: | 4038 6056 02 |
| Деталь: | CONTROL PANEL ASSY |
| Парткод: | 4038 6057 02 |
| Деталь: | COVER ASSY |
| Парткод: | 4038 0775 00 |
| Деталь: | BRACKET |
| Парткод: | 4038 2265 03 |
| Деталь: | MICRO-SWITCH |
| Парткод: | 9331 2200 21 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2283 02 |
| Деталь: | HOL0ER |
| Парткод: | 4038 2281 03 |
| Деталь: | CONNECTOR PIN |
| Парткод: | 4136 6751 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6815 02 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2282 03 |
| Деталь: | COVER |
| Парткод: | 4038 1101 06 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038 1014 01 |
| Деталь: | COVER |
| Парткод: | 4038 1102 02 |
| Деталь: | LABEL |
| Парткод: | 4038 7308 01 |
| Деталь: | LABEL |
| Парткод: | 4038 7309 01 |
| Деталь: | HOL0ER |
| Парткод: | 4038 1105 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6816 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2305 01 |
| Деталь: | SEESAW-SWITCH |
| Парткод: | 9332 5400 11 |
| Деталь: | PROTECTION |
| Парткод: | 1154 4670 01 |
| Деталь: | FRONT COVER SW ASSY |
| Парткод: | 4131 0326 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6811 02 |
| Деталь: | SHOUL0ER SCREW |
| Парткод: | 4038 2287 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2266 01 |
| Деталь: | PLATE |
| Парткод: | 4038 1103 03 |
| Деталь: | TONER PIPE |
| Парткод: | 4038 0759 00 |
| Деталь: | LABEL WASTE TONER |
| Парткод: | 4038 7311 01 |
| Деталь: | RAIL |
| Парткод: | 4038 2013 04 |
| Деталь: | SCREW |
| Парткод: | 4154 3804 01 |
| Деталь: | Waste Toner Box |
| Парткод: | 4065 611 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1400 81 |
| Деталь: | DUCT |
| Парткод: | 4038 2031 01 |
| Деталь: | DUCT |
| Парткод: | 4038 2033 01 |
| Деталь: | DUCT |
| Парткод: | 4038 2034 04 |
| Деталь: | DUCT |
| Парткод: | 4038 2055 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2241 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2237 01 |
| Деталь: | LEFT COVER |
| Парткод: | 4038 1018 02 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | SEAL |
| Парткод: | 4004 2148 01 |
| Деталь: | FILTER |
| Парткод: | 4038 2085 02 |
| Деталь: | COLLAR |
| Парткод: | 4038 2309 01 |
| Деталь: | RAIL |
| Парткод: | 4038 2195 03 |
| Деталь: | BRACKET |
| Парткод: | 4348 3046 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0902 01 |
| Деталь: | BRACKET |
| Парткод: | 4348 3049 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3016 12 |
| Деталь: | FRAME |
| Парткод: | 4030 3010 02 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | FRAME |
| Парткод: | 4067 3816 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | GEAR 3DT |
| Парткод: | 4425 3013 01 |
| Деталь: | CLUTCH |
| Парткод: | 4030 3034 01 |
| Деталь: | ROLLER |
| Парткод: | 4030 3005 01 |
| Деталь: | HOLDER |
| Парткод: | 4030 3002 02 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4030 3095 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3036 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 3003 01 |
| Деталь: | GEAR 29T |
| Парткод: | 4030 3008 01 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 3020 02 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 3030 01 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3011 02 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 3012 01 |
| Деталь: | SHAFT |
| Парткод: | 4348 3047 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4067 6804 01 |
| Деталь: | FRAME ASSY |
| Парткод: | 4067 0204 03 |
| Деталь: | GEAR 32T |
| Парткод: | 4348 3029 01 |
| Деталь: | COVER |
| Парткод: | 4348 3070 02 |
| Деталь: | UNIVERSAL CASSETTE |
| Парткод: | 4038 0771 00 |
| Деталь: | UNIVERSAL CASSETTE |
| Парткод: | 4038 0770 00 |
| Деталь: | MOTOR |
| Парткод: | 9314 1300 61 |
| Деталь: | FRAME ASSY GEAR |
| Парткод: | 4067 0203 02 |
| Деталь: | 27T SHOULDER |
| Парткод: | 4348 3030 01 |
| Деталь: | SCREW PRESSURE |
| Парткод: | 4030 3224 01 |
| Деталь: | SPRING |
| Парткод: | 4030 3081 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | HOLDER |
| Парткод: | 4030 3083 01 |
| Деталь: | BRACKET |
| Парткод: | 4030 3048 02 |
| Деталь: | BRACKET |
| Парткод: | 4030 3049 01 |
| Деталь: | BRACKET |
| Парткод: | 4030 3208 02 |
| Деталь: | BRACKET |
| Парткод: | 4030 3046 03 |
| Деталь: | MOTOR |
| Парткод: | 9312 1200 31 |
| Деталь: | PWB-I |
| Парткод: | 4037 0104 01 |
| Деталь: | HOLDER |
| Парткод: | 4011 3012 01 |
| Деталь: | BRACKET |
| Парткод: | 4067 3815 02 |
| Деталь: | SCREW |
| Парткод: | 4002 2581 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4067 6801 04 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4067 6805 01 |
| Деталь: | COVER |
| Парткод: | 4067 3820 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4067 6802 01 |
| Деталь: | PWB-Z |
| Парткод: | 4067 0101 02 |
| Деталь: | LEVER |
| Парткод: | 4030 3091 01 |
| Деталь: | HOLDER |
| Парткод: | 4030 3047 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4002 3110 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4002 3131 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4067 6803 02 |
| Деталь: | CLUTCH ASSY |
| Парткод: | 4038 3260 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 3240 01 |
| Деталь: | BUSHING |
| Парткод: | 1274 2611 01 |
| Деталь: | GEAR 30T |
| Парткод: | 4038 3246 01 |
| Деталь: | GEAR 30T |
| Парткод: | 4038 3247 01 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | CAM |
| Парткод: | 4038 3236 01 |
| Деталь: | ROLLER |
| Парткод: | 4131 3001 01 |
| Деталь: | STOP RING |
| Парткод: | 4142 3217 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 3232 01 |
| Деталь: | GEAR 25T |
| Парткод: | 1075 2565 01 |
| Деталь: | CLUTCH |
| Парткод: | 9322 1200 31 |
| Деталь: | SOLENOID |
| Парткод: | 9321 2400 61 |
| Деталь: | BRACKET |
| Парткод: | 4038 3244 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 3249 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | BUSHING |
| Парткод: | 4004 5339 01 |
| Деталь: | SHIELD PLATE |
| Парткод: | 4038 3237 01 |
| Деталь: | DRIVE ASSY |
| Парткод: | 4038 0756 00 |
| Деталь: | REINFORCE PLATE D |
| Парткод: | 4038 3517 02 |
| Деталь: | DRIVE ASSY |
| Парткод: | 4038 0757 00 |
| Деталь: | MOTOR |
| Парткод: | 9314 2400 41 |
| Деталь: | MOTOR |
| Парткод: | 9314 2300 61 |
| Деталь: | RAIL |
| Парткод: | 4038 2019 01 |
| Деталь: | SET PLATE |
| Парткод: | 4038 2038 02 |
| Деталь: | PAWL |
| Парткод: | 4038 2174 03 |
| Деталь: | PAWL |
| Парткод: | 4038 2175 02 |
| Деталь: | PAWL |
| Парткод: | 4038 2173 02 |
| Деталь: | LABEL |
| Парткод: | 4038 7316 01 |
| Деталь: | RAIL |
| Парткод: | 4038 2020 02 |
| Деталь: | RAIL |
| Парткод: | 4038 2021 03 |
| Деталь: | RAIL |
| Парткод: | 4038 2022 02 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6813 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 2107 03 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2109 01 |
| Деталь: | STIRRING MEMBER |
| Парткод: | 4038 2108 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2150 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2110 02 |
| Деталь: | TRAY |
| Парткод: | 4038 3203 01 |
| Деталь: | COVER |
| Парткод: | 4038 3235 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6834 03 |
| Деталь: | GUIDE |
| Парткод: | 4038 3229 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3234 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4038 3233 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | TRAY |
| Парткод: | 4038 3202 02 |
| Деталь: | LABEL CAUTION |
| Парткод: | 4038 7354 01 |
| Деталь: | COVER |
| Парткод: | 4038 3212 02 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 3215 01 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 3253 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 3252 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3256 01 |
| Деталь: | COVER |
| Парткод: | 4038 3213 01 |
| Деталь: | SCREW |
| Парткод: | 4154 3804 01 |
| Деталь: | BRACKET ASSY |
| Парткод: | 4038 0252 03 |
| Деталь: | GEAR 13/18T |
| Парткод: | 4030 3412 01 |
| Деталь: | RACK |
| Парткод: | 4030 3460 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 3272 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6845 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | 4038 3251 02 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4687 3281 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4038 3222 03 |
| Деталь: | BRAKE |
| Парткод: | 4038 3286 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4038 3221 03 |
| Деталь: | SCALE INCH |
| Парткод: | 4038 7352 01 |
| Деталь: | SCALE METRIC |
| Парткод: | 4038 7351 01 |
| Деталь: | BRAKE |
| Парткод: | 4038 3255 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 3214 02 |
| Деталь: | Manual Feed Tray Unit |
| Парткод: | 4038 0763 00 |
| Деталь: | DOOR |
| Парткод: | 4067 3822 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3123 01 |
| Деталь: | SHAFT |
| Парткод: | 4348 3071 01 |
| Деталь: | ROLL |
| Парткод: | 4030 3122 01 |
| Деталь: | HANDLE |
| Парткод: | 4067 3833 01 |
| Деталь: | LEVER |
| Парткод: | 4036 3823 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3116 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4067 3834 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4348 3042 01 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | ROLLER |
| Парткод: | 4348 3011 04 |
| Деталь: | GEAR 19/4DT |
| Парткод: | 4348 3048 01 |
| Деталь: | GEAR 19/32T |
| Парткод: | 4348 3031 01 |
| Деталь: | GEAR 2DT |
| Парткод: | 4348 3032 01 |
| Деталь: | BRACKET |
| Парткод: | 4348 3069 03 |
| Деталь: | GEAR 22T |
| Парткод: | 4348 3028 01 |
| Деталь: | BRACKET |
| Парткод: | 4067 3832 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3115 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4067 3825 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4036 3831 01 |
| Деталь: | RAIL |
| Парткод: | 4038 2023 07 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2029 01 |
| Деталь: | LEVER |
| Парткод: | 4038 2046 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2048 01 |
| Деталь: | ARM |
| Парткод: | 4038 2047 02 |
| Деталь: | SPACER |
| Парткод: | 4038 3594 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2080 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2045 01 |
| Деталь: | SCREW |
| Парткод: | 4154 3804 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2077 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2152 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2153 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2078 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2205 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2207 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2151 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2217 01 |
| Деталь: | RAIL |
| Парткод: | 4038 2024 02 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6836 01 |
| Деталь: | ARM |
| Парткод: | 4038 2027 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2028 01 |
| Деталь: | LEVER |
| Парткод: | 4038 2026 01 |
| Деталь: | TRANSFER KIT |
| Парткод: | 4038 0777 00 |
| Деталь: | SWITCH ASSY |
| Парткод: | 4038 0761 00 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6835 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4030 3212 01 |
| Деталь: | GUIDE |
| Парткод: | 4658 3048 01 |
| Деталь: | LABEL CARRYING CAPACITY |
| Парткод: | 4002 7306 01 |
| Деталь: | STOPPER |
| Парткод: | 4658 3049 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030 3214 02 |
| Деталь: | GUIDE |
| Парткод: | 4030 3215 01 |
| Деталь: | GEAR 14T |
| Парткод: | 4658 3012 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 3217 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3228 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3227 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4037 3213 01 |
| Деталь: | SHAFT |
| Парткод: | 4498 3826 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4498 3825 01 |
| Деталь: | LEVER |
| Парткод: | 4128 3823 01 |
| Деталь: | KNOB |
| Парткод: | 4037 3204 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4030 3211 02 |
| Деталь: | CASSETTE |
| Парткод: | 4030 3201 03 |
| Деталь: | BUSHING |
| Парткод: | 0992 3014 01 |
| Деталь: | SCREW |
| Парткод: | 4498 3834 01 |
| Деталь: | BRACKET |
| Парткод: | 4030 3216 01 |
| Деталь: | BRACKET |
| Парткод: | 4030 3218 01 |
| Деталь: | LEVER |
| Парткод: | 4002 3108 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3207 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3021 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3020 01 |
| Деталь: | BUSHING |
| Парткод: | 1274 3603 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 3205 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3206 01 |
| Деталь: | ROLLER |
| Парткод: | 4038 5887 01 |
| Деталь: | ROLL |
| Парткод: | 4131 3904 02 |
| Деталь: | SHAFT |
| Парткод: | 4025 5984 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 5890 02 |
| Деталь: | COLLAR |
| Парткод: | 4139 5577 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 5891 02 |
| Деталь: | BUSHING |
| Парткод: | 4038 5860 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 5884 03 |
| Деталь: | ROLLER |
| Парткод: | 4038 5901 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 5885 01 |
| Деталь: | DUCT |
| Парткод: | 4038 5869 01 |
| Деталь: | WASHER |
| Парткод: | 1200 1646 03 |
| Деталь: | TIMING BELT 144L |
| Парткод: | 4038 5893 01 |
| Деталь: | PULLEY 24/16T |
| Парткод: | 4038 5897 01 |
| Деталь: | Pulley 24T |
| Парткод: | 4038 5898 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 5889 02 |
| Деталь: | GEAR 23/21T |
| Парткод: | 4038 5870 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4038 5873 01 |
| Деталь: | GEAR 33/32T |
| Парткод: | 4038 5879 01 |
| Деталь: | GEAR 24/2DT |
| Парткод: | 4038 5877 02 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 5862 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 5864 01 |
| Деталь: | LEVER |
| Парткод: | 4038 5863 01 |
| Деталь: | BRACKET ASSY |
| Парткод: | 4038 0212 01 |
| Деталь: | BRACKET ASSY |
| Парткод: | 4038 0213 01 |
| Деталь: | LEVER |
| Парткод: | 4038 5861 02 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 5874 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 5872 02 |
| Деталь: | GEAR 17/16T |
| Парткод: | 4038 5871 02 |
| Деталь: | GEAR 14T |
| Парткод: | 4038 5876 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 5888 02 |
| Деталь: | HOLDER |
| Парткод: | 4038 2275 01 |
| Деталь: | IU CONTACT PLATE ASSY |
| Парткод: | 4038 0760 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2233 02 |
| Деталь: | SCREW |
| Парткод: | 4154 3804 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2313 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2206 02 |
| Деталь: | HOLDER |
| Парткод: | 4038 2274 01 |
| Деталь: | COVER |
| Парткод: | 4038 2255 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2222 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2277 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2276 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2225 02 |
| Деталь: | COVER |
| Парткод: | 4038 2232 01 |
| Деталь: | HV TRANSFORMER |
| Парткод: | 4038 6203 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2118 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2076 01 |
| Деталь: | PIPE |
| Парткод: | 4038 2116 03 |
| Деталь: | STIRRING PLATE |
| Парткод: | 4038 2131 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2117 02 |
| Деталь: | CUSHION |
| Парткод: | 4038 2025 01 |
| Деталь: | LID |
| Парткод: | 4038 2115 02 |
| Деталь: | BUSHING |
| Парткод: | 4004 5607 02 |
| Деталь: | GEAR 18/3DT |
| Парткод: | 4004 2545 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2579 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2586 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4004 5612 01 |
| Деталь: | PIPE |
| Парткод: | 4038 2111 01 |
| Деталь: | SCREW |
| Парткод: | 4038 2112 02 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2114 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2143 01 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2142 01 |
| Деталь: | BUSHING |
| Парткод: | 4038 2120 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | BRACKET ASSY |
| Парткод: | 4038 0203 02 |
| Деталь: | STOP PLATE |
| Парткод: | 4038 2089 01 |
| Деталь: | GEAR 32/3DT |
| Парткод: | 4038 2140 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4038 2130 01 |
| Деталь: | SHUTTER |
| Парткод: | 4038 2113 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2119 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2062 01 |
| Деталь: | Label M1 |
| Парткод: | 4038 7303 01 |
| Деталь: | HANDLE |
| Парткод: | 4038 3532 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3529 02 |
| Деталь: | GUIDE |
| Парткод: | 4038 3539 01 |
| Деталь: | ROLLER |
| Парткод: | 4038 3501 01 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 21 |
| Деталь: | GUIDE |
| Парткод: | 4038 3537 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3538 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3536 01 |
| Деталь: | ROLLER |
| Парткод: | 4038 3502 02 |
| Деталь: | GUIDE |
| Парткод: | 4038 3540 03 |
| Деталь: | GUIDE |
| Парткод: | 4038 3526 04 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 3535 02 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 3530 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 3525 01 |
| Деталь: | BUSHING |
| Парткод: | 4025 3572 01 |
| Деталь: | GEAR 2DT |
| Парткод: | 4004 3503 02 |
| Деталь: | GEAR 14T |
| Парткод: | 4004 3504 02 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3567 01 |
| Деталь: | RESISTOR |
| Парткод: | 9455 8076 01 |
| Деталь: | SEAL |
| Парткод: | 4128 3522 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4038 3562 01 |
| Деталь: | PRISM |
| Парткод: | 9335 1400 11 |
| Деталь: | WASHER |
| Парткод: | 4038 3593 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3592 01 |
| Деталь: | PHOTO SENSING ELEMENT |
| Парткод: | 9372 1300 12 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 3531 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6830 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 3561 03 |
| Деталь: | HUMIDITY CONVERTION EL. |
| Парткод: | 9372 5400 31 |
| Деталь: | TORSION SPRING |
| Парткод: | 1164 3527 02 |
| Деталь: | CLUTCH |
| Парткод: | 9322 1300 21 |
| Деталь: | SEAL |
| Парткод: | 4038 3556 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 3559 01 |
| Деталь: | COVER |
| Парткод: | 4038 3558 02 |
| Деталь: | GUIDE |
| Парткод: | 4038 3527 03 |
| Деталь: | TRANSPORT UNIT |
| Парткод: | 4038 0751 00 |
Коды ошибок
C0001
C0102
C0204
C0206
C0208
C0209
C0210
C0211
C0212
C0213
C0214
C0215
C0301
C1180
C1181
C1182
C1183
C1190
C1192
C1193
C11A1
C11A2
C11A4
C11B0
C11B1
C11B2
C11B4
C11C1
C11C2
C11C3
C11C5
C1401
C2151
C2152
C2253
C2254
C2255
C2256
C2451
C2551
C2552
C2553
C2554
C2555
C2556
C2557
C2558
C2559
C255A
C255B
C255C
C2651
C2652
C2653
C2654
C2A01
C2A02
C2A03
C2A04
C3301
C3302
C3451
C3452
C3461
C3751
C3752
C3851
C3852
C3A01
C3A02
C4151
C4152
C4153
C4154
C4551
C4552
C4553
C4554
C4705
C4761
C4765
C4770 ... C4773
C4780 ... C4783
C5102
C5103
C5351
C5353
C5354
C5357
C5358
C6102
C6103
C6301
C6704
C6751
C9401
C9402
CA051
CA052
CA053
CB001 ... CB119
CD004 ... CD011
CF001 ... CFF15
Описание
| Error code: | C0001 |
| Description: | Main Motor turning at abnormal timing The Main Motor Lock signal remains faulty for a predetermined continuous period of time while the Main Motor remains stationary. |
| Remedy: | 1 Main Motor rotation while it is being energized: the voltage across PJ13I-7A on Master Board and GND remains DC 0 V. YES: Change Master Board. NO: Change motor. |
| Error code: | C0102 |
| Description: | LCT vertical transport motor malfunction |
| Error code: | C0204 |
| Description: | Yellow PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 2 upper limit sensor (PS14) • Tray 2 lift-up motor (M8) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0206 |
| Description: | Black PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 3 upper limit sensor (PS22) • Tray 3 lift-up motor (M23) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0208 |
| Description: | Tray 5 feeder up/down abnormality |
| Causes: | • Tray 4 upper limit sensor (PS27) • Tray 4 lift-up motor (M24) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Error code: | C0209 |
| Description: | LCT elevator motor malfunction |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0211 |
| Description: | Tray 1 feeder up/down abnormality • The paper feed tray 1 lift-up position sensor is not unblocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The paper feed tray 1 lift-up position sensor is not blocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started. |
| Causes: | • Bypass lift-up motor (M26) • Bypass upper limit sensor (PS35) • Bypass lower limit sensor (PS36) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check the connector of M1 for proper drive coupling and correct as necessary. 3 PS17 I/O check PRCB CN6PRCB-7 (ON) D-2. 4 SL1 operation check PRCB CN6PRCB-4 (ON) D-1. 5 M1 operation check PRCB CN34PRCB-10 (REM) PRCB CN34PRCB-13 (LOCK) D-22. 6 Change SL1. 7 Change M1. 8 Change PRCB. |
| Error code: | C0212 |
| Description: | LCT ejection failure |
| Error code: | C0213 |
| Description: | LCT shift gate malfunction |
| Error code: | C0214 |
| Description: | LCT shifting failure |
| Causes: | • Shifter motor (M133) • Shifter stop / lower limit position sensor (PS138) • Shifter home sensor (PS139) • PC control board (PCCB) |
| Error code: | C0215 |
| Description: | LCT shift motor malfunction |
| Error code: | C0301 |
| Description: | Suction fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Suction fan (FM1) • Paper feed/transport drive board (PFTDB) |
| Remedy: | 1 Check the FM8 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM8 operation check PRCB CN3PRCB-2 (ON) PRCB CN3PRCB-3 (LOCK) D-4 to 5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C1180 |
| Description: | Transport system drive malfunctions |
| Error code: | C1181 |
| Description: | Paddle motor malfunctions |
| Error code: | C1182 |
| Description: | Unsupported option trouble |
| Causes: | When JS-504 is installed: Shift motor (M2) Shift home sensor (PS6) JS control board (JSCB). When FS-527 is installed: Tray2 shift motor (M16) Tray2 shift home sensor (PS25) FS control board (FSCB) |
| Error code: | C1183 |
| Description: | Finishing option elevator drive malfunction |
| Causes: | Elevate motor (M15) Tray1 lower position sensor (PS21) Tray1 upper position sensor (PS24) Tray1 upper position switch (SW2) Tray1 lower position switch (SW3) FS control board (FSCB) |
| Error code: | C1190 |
| Description: | Finishing option aligning bar moving mechanism malfunction 1 |
| Causes: | Alignment plate motor (M13) Alignment plate home sensor (PS17) FS control board (FSCB) |
| Error code: | C1192 |
| Description: | Front aligning plate motor malfunctions |
| Error code: | C1193 |
| Description: | Rear aligning plate motor malfunctions |
| Error code: | C11A1 |
| Description: | Finishing option exit roller pressure/retraction failure |
| Causes: | Exit roller retraction motor (M9) Exit roller pressure sensor (PS12) FS control board (FSCB) |
| Error code: | C11A2 |
| Description: | Saddle exit roller pressure/retraction failure |
| Causes: | <When FS-536 or FS-536SD is installed> • Receiving roller retraction motor (M4) • Receiving roller retraction sensor (PS11) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Receiving roller retraction motor (M10) • Receiving roller retraction sensor (PS22) • FS control board (FSCB) |
| Error code: | C11A4 |
| Description: | Saddle exit motor failure Booklet exit motor malfunctions |
| Error code: | C11B0 |
| Description: | Finishing option stapler unit CD drive failure |
| Causes: | Stapler movement motor (M11) Stapler home sensor/1 (PS18) Stapler home sensor/2 (PS19) FS control board (FSCB) |
| Error code: | C11B1 |
| Description: | Stapler unit slide motor malfunctions |
| Error code: | C11B2 |
| Description: | Finishing option stapling mechanism malfunction 1 |
| Causes: | Stapler unit FS control board (FSCB) |
| Error code: | C11B4 |
| Description: | Stapler/folding motor malfunctions |
| Error code: | C11C1 |
| Description: | Punch control board malfunctions |
| Error code: | C11C2 |
| Description: | Punch side registration motor malfunctions |
| Error code: | C11C3 |
| Description: | Punch motor malfunctions |
| Error code: | C11C5 |
| Description: | Punch sensor malfunctions |
| Causes: | Paper size detect board (PSDTB) |
| Error code: | C1401 |
| Description: | Backup RAM failure |
| Error code: | C2151 |
| Description: | Secondary transfer roller pressure welding alienation • During a retraction operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its retracted position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. • During a pressure operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its pressed position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. |
| Causes: | • 2nd transfer pressure motor (M3) • 2nd transfer pressure sensor (PS50) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M11 connector for proper connection and correct as necessary. 2 Check the connector of M11 for proper drive coupling and correct as necessary. 3 PS36 I/O check PRCB CN3PRCB-9 (ON) D-5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C2152 |
| Description: | Transfer belt pressure welding alienation • During a retraction operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its retracted position within a predetermined period of time after the transfer belt retraction clutch is turned ON. • During a pressure operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its pressed position within a predetermined period of time after the transfer belt clutch is turned ON. |
| Causes: | • 1st transfer pressure sensor/K (PS51) • 1st transfer pressure sensor/YMC (PS52) • 1st transfer pressure motor (M21) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 PS31 I/O check PRCB CN36PRCB-15 (ON) D-26 to 27. 3 CL7 operation check PRCB CN39PRCB-10 (ON) D-23. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change CL7. 6 Change M5. 7 Change PRCB. |
| Error code: | C2253 |
| Description: | Color PC motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/YMC (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2254 |
| Description: | Color PC motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/YMC motor (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2255 |
| Description: | Developing motor’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Developing motor/YMC (M17) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M21-PRCB CN32 for proper connection and correct as necessary. 2 Check the M21 connector for proper drive coupling and correct as necessary. 3 M21 operation check PRCB CN32-2 (REM) PRCB CN32-5 (LOCK). bizhub C224 25-I to J 4 Replace M21. 5 Replace PRCB. |
| Error code: | C2256 |
| Description: | Developing motor’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Developing motor/YMC (M17) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M21-PRCB CN32 for proper connection and correct as necessary. 2 Check the M21 connector for proper drive coupling and correct as necessary. 3 M21 operation check PRCB CN32-2 (REM) PRCB CN32-5 (LOCK). bizhub C224 25-I to J 4 Replace M21. 5 Replace PRCB. |
| Error code: | C2451 |
| Description: | Release new transfer belt unit • A new installation is not detected when a new transfer cleaner unit (image transfer belt unit) is installed. |
| Remedy: | 1 Reinstall unit. 2 Check there is a short circuit in the fuse of the transfer belt unit. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Change PRCB. |
| Error code: | C2551 |
| Description: | Abnormally low toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2552 |
| Description: | Abnormally high toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2553 |
| Description: | Abnormally low toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2554 |
| Description: | Abnormally high toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2555 |
| Description: | Abnormally low toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2556 |
| Description: | Abnormally high toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2557 |
| Description: | Abnormally low toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Developing unit • Toner cartridge • Toner empty sensor/K (PZS/K) • Toner supply motor/K (M12) • Toner cartridge motor/CK (M14) • MFP board (MFPB) |
| Remedy: | 1 M3 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 D-23. 2 Reinstall imaging unit. 3 Reinstall toner cartridge. 4 Change imaging unit /K. 5 Change PRCB. |
| Error code: | C2558 |
| Description: | Abnormally high toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Developing unit • Toner cartridge • Sub hopper unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit /K. 4 Change PRCB. |
| Error code: | C2559 |
| Description: | Cyan TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255A |
| Description: | Magenta TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255B |
| Description: | Yellow TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255C |
| Description: | Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit /K. 2 Change imaging unit /K. 3 Change PRCB. |
| Error code: | C2651 |
| Description: | EEPROM access error (IU C) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2652 |
| Description: | EEPROM access error (IU M) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2653 |
| Description: | EEPROM access error (IU Y) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2654 |
| Description: | EEPROM access error (IU K) |
| Causes: | Imaging unit /C Imaging unit /M Imaging unit /Y Drum unit /K Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2A01 |
| Description: | EEPROM access error (TC C) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C2A02 |
| Description: | EEPROM access error (TC M) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C2A03 |
| Description: | EEPROM access error (TC Y) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C2A04 |
| Description: | EEPROM access error (TC K) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C3301 |
| Description: | Fusing cooling fan motor/ 1 failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Remedy: | 1 Check the FM9 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM9 operation check PRCB CN40PRCB-2 (ON) PRCB CN40PRCB-3 (LOCK) D-19. 4 Change FM9. 5 Change PRCB. |
| Error code: | C3302 |
| Description: | Fusing cooling fan motor/ 2,3 failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Paper cooling fan (FM8) • Printer control board (PRCB) |
| Remedy: | 1 Check the FM10 or FM11 connector for proper connection and correct as necessary 2 Check the fan for possible overload and correct as necessary. 3 FM10/FM11 operation check PRCB CN40PRCB-5 (ON) PRCB CN40PRCB-6 (LOCK) D-19. PRCB CN40PRCB-8 (ON) PRCB CN40PRCB-9 (LOCK) D-18. 4 Change FM10/FM11. 5 Change PRCB. |
| Error code: | C3451 |
| Description: | Heating Roller warm-up failure • The temperature of the Heating Roller does not reach 100 °C within 50 sec. after the Heating Roller Heater Lamp has been turned ON. • The temperature of the Heating Roller does not reach 100 °C and that of the Fusing Pressure Roller does not reach 195 °C within 200 sec. after the Heating Roller Heater Lamp has been turned ON. • The voltage of the Heating Roller Thermistor does not increase by five steps within 20 sec. after the Heating Roller Heater Lamp has been turned ON. • No zero cross signal is detected even with the lapse of 1 sec. or more after the Heating Roller Heater Lamp has been turned ON. |
| Causes: | Fusing unit Right door switch (SW2) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1. |
| Error code: | C3452 |
| Description: | Fusing Pressure Roller warm-up failure • The voltage of the Fusing Pressure Roller Thermistor does not increase by five steps within 20 sec. after the predrive of the Fusing Roller has been started during a warm-up cycle. |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1. |
| Error code: | C3461 |
| Description: | Release new fusing unit • A new installation is not detected when a new fusing Unit is installed. |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 3 Reinstall fusing unit. 4 Change fusing unit. 5 Change PRCB. |
| Error code: | C3751 |
| Description: | Heating Roller abnormally high temperature • A temperature of 225 °C or more of the Heating Roller is detected for 1 sec. or more. |
| Causes: | Fusing unit Right door switch (SW2) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1. |
| Error code: | C3752 |
| Description: | Fusing Pressure Roller abnormally high temperature • A temperature of 190 °C or more of the Fusing Pressure Roller is detected for 1 sec. or more before the start of the heater temperature control. • A temperature of 215 °C or more of the Fusing Pressure Roller is detected for 1 sec. or more after the start of the heater temperature control. |
| Causes: | Fusing unit Right door switch (SW2) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1. |
| Error code: | C3851 |
| Description: | Heating Roller abnormally low temperature • No zero cross signal is detected even with the lapse of 1 sec. or more during a standby state, print cycle, or Power Save. • A temperature of 120 °C or less of the Heating Roller is detected for 1 sec. or more during a standby state. • A temperature of 120 °C or less of the Heating Roller is detected for 1 sec. or more during a print cycle. • A temperature of 70 °C or less of the Heating Roller is detected for 1 sec. or more during Power Save. |
| Causes: | Fusing unit Right door switch (SW2) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1. |
| Error code: | C3852 |
| Description: | Fusing Pressure Roller abnormally low temperature • . A temperature of 80 °C or less of the Fusing Pressure Roller is detected for 1 sec. or more during a standby state. • A temperature of 80 °C or less of the Fusing Pressure Roller is detected for 1 sec. or more during a print cycle. • A temperature of 80 °C or less of the Fusing Pressure Roller is detected for 1 sec. or more during Power Save. |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1. |
| Error code: | C3A01 |
| Description: | PIC Board malfunction The PIC Board is faulty. |
| Remedy: | 1 The same malfunction recurs even after the malfunction has been reset, Power Switch turned OFF and ON, and the power cord plugged out and back in. YES: Change PIC Board. |
| Error code: | C3A02 |
| Description: | Paper Stuck to Fuser Pressure Roller • The temperature of the Fusing Pressure Roller Thermistor /1 (TH2) goes down by a given level of degree compared to the temperature of a given period of time before when the paper passes on the Timing Roller and blocks the Exit Sensor (PC2). |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M for proper connection and correct or change as necessary. 3 PC2 I/O check, Sensor check PWB-M CNTH2-8 (ON) C-13. 4 Change Fusing Unit. 5 Change PWB-M. 6 Change PU1. |
| Error code: | C4151 |
| Description: | Polygon motor rotation trouble (C) • The polygon motor fails to turn stably even after the lapse of a given period of time after activating the polygon motor. • Motor lock signal detects HIGH for a given period time consecutively during the polygon motor is rotating. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4152 |
| Description: | Polygon motor rotation trouble (M) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4153 |
| Description: | Polygon motor rotation trouble (Y) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4154 |
| Description: | Polygon motor rotation trouble (K) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4551 |
| Description: | Laser malfunction (C) • SOS signal is not detected even after the lapse of a given period of time after staring the laser output. • SOS signal is not detected for a given period of time during printing or image stabilization adjustment. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4552 |
| Description: | Laser malfunction (M) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4553 |
| Description: | Laser malfunction (Y) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4554 |
| Description: | Laser malfunction (K) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4705 |
| Description: | Printer Time Out • No image data is output from the MFP Control Board (PWB-MFPC). |
| Remedy: | 1 Select Service Mode - State Confirmation - Memory/HDD Adj. - Memory Bus Check - Memory-PRT. 2 Check the connectors on PWB-MFPC for proper connection and correct as necessary. 3 Change PWB-MFPC. |
| Error code: | C4761 |
| Description: | Compression hardware timeout • The hardware involved with the compression function offered by the MFP Control Board (PWBMFPC) does not respond. |
| Remedy: | Change PWB-MFPC |
| Error code: | C4765 |
| Description: | Extraction hardware timeout • The hardware involved with the extraction function offered by the MFP Control Board (PWBMFPC) does not respond. |
| Remedy: | Change PWB-MFPC |
| Error code: | C4770 ... C4773 |
| Description: | JBIG Error • Memory of the MFP Control Board (PWB-MFPC) is faulty. |
| Remedy: | Change PWB-MFPC |
| Error code: | C4780 ... C4783 |
| Description: | The MFP Control Board (PWB-MFPC) is faulty. |
| Remedy: | Change PWB-MFPC |
| Error code: | C5102 |
| Description: | Main high-voltage error C |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5103 |
| Description: | Main high-voltage error M |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5351 |
| Description: | Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • DC power supply cooling fan (FM9) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1 Check the FM5 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check PRCB CN30PRCB-11 (ON) PRCB CN30PRCB-12 (LOCK) K-8. 4 Change FM5. 5 Change DCPU. 6 Change PRCB. |
| Error code: | C5353 |
| Description: | Cooling fan motor/2’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Cooling fan motor/2 (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM2 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM2 operation check PRCB CN28PRCB-2 (ON) PRCB CN28PRCB-3 (LOCK) D-24. 4 Change FM2. 5 Change PRCB. |
| Error code: | C5354 |
| Description: | Exhaust fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Ozone ventilation fan (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM4 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM4 operation check PRCB CN3PRCB-14 (ON) PRCB CN3PRCB-16 (LOCK) D-6. 4 Change FM4. 5 Change PRCB. |
| Error code: | C5357 |
| Description: | Cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Machine cooling fan (FM1) • CPU board (CPUB) • Base board (BASEB) |
| Remedy: | 1 Check the FM1 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM1 operation check PRCB CN30PRCB-4 (ON) PRCB CN30PRCB-6 (LOCK) K-7. 4 Change FM1. 5 Change PRCB. |
| Error code: | C5358 |
| Description: | Fusing power supply cooling fan’s failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan remains stationary. |
| Causes: | • Fusing power supply cooling fan (FM12) • Expansion control board (EXCB) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between FM12-EXCB CN6 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM12 operation check EXCB CN6-1 (REM) 23-TM). 4 Replace FM12. 5 EXCB ICP1 conduction check. 6 Replace EXCB. 7 Replace PRCB. |
| Error code: | C6102 |
| Description: | Drive system home sensor malfunction • The scanner home sensor (PS201) is unable to detect the scanner located at its home position. • The scanner home sensor (PS201) is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor (PS201) detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor (PS201). |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6103 |
| Description: | Slider over running The scanner home sensor (PS201) detects the scanner at its home position during a period of time that begins with the time when a prescan command and a scan preparation command are executed and ends when a home return command is executed. |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6301 |
| Description: | Optical cooling fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | Optical cooling fan motor (M202) Scanner relay board (REYB/SCAN) MFP board (MFPB) |
| Remedy: | 1 Check the FM201 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 M202 operation check REYB/SCAN PJ4-3 (LOCK) P-18 4 Change REYB/SCAN - - 5 Change MFPB |
| Error code: | C6704 |
| Description: | Image input time out. Image data is not input from the scanner to the MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Memory Bus Check] -> [Scanner -> Memory], and conduct the memory bus function. 2. Correct the harness connection between scanner section and MFPB if faulty. 3. MFPB F3E conduction check 4. Replace MFPB. 5. Replace the CCD unit. |
| Error code: | C6751 |
| Description: | CCD gain adjustment failure. • The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment. |
| Causes: | • LED exposure unit • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 2. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 3. Correct the harness connection between SCDB CN1-DCPU CN005 if faulty. 4. Check for possible extraneous light and correct as necessary. 5. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 6. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 7. Replace SCDB 8. Replace the CCD unit. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | C9401 |
| Description: | Exposure LED lighting failure The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | C9402 |
| Description: | Exposure LED lighting abnormally The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | CA051 |
| Description: | Standard controller configuration failure • The controller of the printer control board (PRCB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA052 |
| Description: | Controller hardware error • A controller hardware error is detected in the network I/F. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA053 |
| Description: | Controller start failure • A controller start failure is detected in the controller interface. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CB001 ... CB119 |
| Description: | FAX board error |
| Error code: | CD004 ... CD011 |
| Description: | HDD error |
| Error code: | CF001 ... CFF15 |
| Description: | MFP Control Board error |
