Konica-Minolta bizhub C280
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
75000
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Печать фотографий |
|
Факс |
|
Цветность печати |
цветная |
Телефон |
|
Размещение |
напольный |
Макс. формат |
A3 |
Область применения |
средний офис |
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Число страниц в месяц |
75 000 |
Копир |
|
Тип устройства |
МФУ |
Сканер |
|
Принтер |
|
Пигментные чернила |
|
Печать без полей |
|
Время разогрева |
45 |
Прямая печать |
|
Двусторонняя печать |
|
Количество цветов |
4 |
Макс, разрешение для ч/б печати |
|
| По X | 1 800 |
| По X | 600 |
| По Y | 600 |
Скорость ч/б печати |
|
| A3 | 17 |
Скорость цветной печати |
|
| A4 | 28 |
Время выхода первого отпечатка |
|
| Цветн, | 7,7 |
| Ч/б | 5,8 |
Копир |
|
Макс, количество копий за цикл |
9 999 |
Шаг масштабирования |
0,1 |
Время выхода первой копии |
5,8 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По Y | 600 |
| По X | 600 |
Сканер |
|
Слайд-адаптер |
|
Емкость устройства автоподачи оригиналов |
100 |
Оттенки серого |
256 |
Тип сканера |
планшетный/протяжный |
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Макс. формат оригинала |
A3 |
Макс, размер сканирования |
|
| По X | 297 |
| По Y | 320 |
Разрешение сканера |
|
| По Х | 600 |
Скорость сканирования |
|
| Цветн, | 70 |
| Ч/б | 70 |
Расходные материалы |
|
Количество картриджей |
4 |
Ресурс ч/б картриджа/тонера |
29 000 |
Ресурс цветного картриджа/тонера |
26 000 |
Печать на: |
|
| Рулоне |
|
| CD/DVD |
|
| Карточках |
|
| Пленках |
|
| Матовой бумаге |
|
| Конвертах |
|
| Этикетках |
|
| Глянцевой бумаге |
|
Плотность бумаги |
|
| Минимальная | 60 |
| Максимальная | 271 |
Факс |
|
Цветной |
|
Телефон |
|
Проводная трубка |
|
АОН |
|
Беспроводная трубка |
|
Спикерфон |
|
Стандарт DECT |
|
Автоответчик |
|
Caller ID |
|
Шрифты и языки управления |
|
Языки управления |
|
| PostScript 2 |
|
| PPDS |
|
| PCL 5e |
|
| PostScript |
|
|
|
|
| PostScript 3 |
|
Количество установленных шрифтов |
|
| PCL | 80 |
| PostScript | 137 |
Лотки |
|
Емкость лотка ручной подачи |
150 |
Подача бумаги |
|
| Максимальная | 3 650 |
| Стандартная | 1 150 |
Вывод бумаги |
|
| Максимальный | 3 200 |
| Стандартный | 250 |
Финишер |
|
Сортировка со сдвигом |
|
Сортер |
|
Брошюровщик |
|
Степлер |
|
Электронная сортировка |
|
Интерфейсы |
|
LPT |
|
Устройство для чтения карт памяти |
|
RS-232 |
|
Инфракрасный порт |
|
FireWire (IEEE 1394) |
|
Wi-Fi |
|
Bluetooth |
|
Ethernet (RJ-45) |
|
USB |
|
Версия USB |
2,0 |
Память/Процессор |
|
Емкость жесткого диска |
250 |
Частота процессора |
1 000 |
Процессор |
MPC8533 |
Объем памяти |
2 048 |
Дополнительная информация |
|
Диагональ дисплея |
8,5 |
Экран |
|
Поддержка ОС |
|
| DOS |
|
| Linux |
|
| Mac OS |
|
| Windows |
|
Потребляемая мощность |
|
| При работе | 1 500 |
Габариты |
|
Глубина |
842 |
Ширина |
643 |
Вес |
98 |
Высота |
770 |
Модули
1ST PAPER FEED SECTION
VERTICAL CONVEYANCE DOOR SECTION
SCANNER DRIVE SECTION
CASSETTE RAIL SECTION
MANUAL FEED TRAY UNIT
TRANSFER BELT UNIT
SHIELD BOX
2ND CASSETTE SECTION
Control panel
IR COVER
PAPER FEED DRIVE
PAPER EXIT SECTION
TONER SUPPLY SECTION
PH UNIT
1ST CASSETTE SECTION
MAIN POWER SUPPLY UNIT
D/C RAIL SECTION
ERASE LAMP SECTION
Fusing Drive Section
2ND PAPER FEED SECTION
EXTERNAL PARTS
REAR FAN SECTION
Vertical conveyance Section
HIGH VOLTAGE UNIT
BOTTLE DRIVE SECTION
IR FRAME
FUSING SECTION/ WASTE TONER BOX
CCD UNIT/ SCANNER SECTION
MAIN DRIVE SECTION
Детали VERTICAL CONVEYANCE DOOR SECTION
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5609 00 |
| Деталь: | Photoreflector |
| Парткод: | A0ED M501 00 |
| Деталь: | Paperfeed Wiring /1 |
| Парткод: | A0ED N10F 00 |
| Деталь: | Paperfeed Wiring /1 |
| Парткод: | A0ED N11D 00 |
| Деталь: | Frame /Front |
| Парткод: | A0ED 5601 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 5612 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3016 12 |
| Деталь: | GEAR 30T |
| Парткод: | 4425 3013 01 |
| Деталь: | CLUTCH |
| Парткод: | A02E 5611 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | GEAR 29T |
| Парткод: | 4030 3008 01 |
| Деталь: | Paper feed Holder |
| Парткод: | A00J 5601 00 |
| Деталь: | Shaft /P |
| Парткод: | A00J 5640 00 |
| Деталь: | SHAFT |
| Парткод: | 4040 3097 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5603 02 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5668 01 |
| Деталь: | LEVER |
| Парткод: | A02E 5613 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 5605 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 5608 00 |
| Деталь: | Gear 26/36T |
| Парткод: | A0ED 5661 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M202 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5651 00 |
| Деталь: | Paper Feed Assy (1st) |
| Парткод: | A0ED R731 00 |
| Деталь: | Paper Feed Assy (1st)3 |
| Парткод: | A0ED R732 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5685 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0ED 5684 00 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3125 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5612 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 5610 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5638 00 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3017 03 |
| Деталь: | BRACKET |
| Парткод: | 4030 3014 01 |
| Деталь: | HOLDER |
| Парткод: | 4030 3013 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3078 01 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A02E F566 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5636 00 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A02E R729 00 |
| Деталь: | COVER |
| Парткод: | A0ED 7142 00 |
| Деталь: | Cover Door Upper |
| Парткод: | A0ED 7116 00 |
| Деталь: | Door /Right |
| Парткод: | A0ED 7106 00 |
| Деталь: | LOCK CLAW |
| Парткод: | A0ED 7121 00 |
| Деталь: | LEVER |
| Парткод: | A0ED 7108 00 |
| Деталь: | CLAW |
| Парткод: | A0ED 7104 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 7103 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 7105 00 |
| Деталь: | LOCK CLAW |
| Парткод: | A0ED 5988 00 |
| Деталь: | Caulking (Reinforce Plate Door Fron t) |
| Парткод: | A0ED G812 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0ED 7147 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 7120 00 |
| Деталь: | POSITIONING PLATE |
| Парткод: | A0ED 7110 00 |
| Деталь: | LEVER |
| Парткод: | A0ED 7100 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 7145 00 |
| Деталь: | Caution Label |
| Парткод: | A0ED 9400 00 |
| Деталь: | Connecting Plate |
| Парткод: | A0ED 5938 00 |
| Деталь: | Door Assy(Vertical Transport) |
| Парткод: | A0ED R722 11 |
| Деталь: | SHAFT |
| Парткод: | A02E 5953 02 |
| Деталь: | SPACER |
| Парткод: | A0ED 5989 00 |
| Деталь: | CAM |
| Парткод: | A02E 5960 02 |
| Деталь: | COVER |
| Парткод: | A0ED 5912 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 5963 00 |
| Деталь: | FEED ROLLER |
| Парткод: | A02E 5947 00 |
| Деталь: | STOP RING |
| Парткод: | 4142 3217 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 5957 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0ED 5916 00 |
| Деталь: | GEAR 28T |
| Парткод: | A0ED 5955 00 |
| Деталь: | GEAR 22T |
| Парткод: | A02E 5954 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | GEAR 30T |
| Парткод: | A02E 5961 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M201 00 |
| Деталь: | SOLENOID |
| Парткод: | 9J06 M200 00 |
| Деталь: | COVER |
| Парткод: | A0ED 5978 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5952 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5956 00 |
| Деталь: | Light blocking Plate |
| Парткод: | A0ED 5965 00 |
| Деталь: | CLUTCH ASSY |
| Парткод: | A02E 5951 00 |
| Деталь: | WtoW Connector |
| Парткод: | V651 0100 42 |
| Деталь: | CONNECTOR |
| Парткод: | V651 0100 01 |
| Деталь: | COVER |
| Парткод: | A0ED 5977 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 5917 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 5905 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 5919 00 |
| Деталь: | ROLL |
| Парткод: | 4030 3122 01 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED 7144 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 7143 00 |
| Деталь: | COVER |
| Парткод: | A0ED 7146 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5972 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3475 01 |
| Деталь: | HOLDER |
| Парткод: | A0ED 5971 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5976 00 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | 4034 0151 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5993 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5940 00 |
| Деталь: | GUIDE |
| Парткод: | 4030 3403 01 |
| Деталь: | SEAL |
| Парткод: | 4030 3489 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 5973 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5915 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5902 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5901 00 |
| Деталь: | VIBRATIONPROOF PART |
| Парткод: | A0ED 5997 00 |
| Деталь: | Paper Separation Assy(Multiple Bypa ss) |
| Парткод: | A0ED R730 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0ED 8201 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0ED 8206 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0ED 8204 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0ED 8203 00 |
| Деталь: | ROLLER |
| Парткод: | A0ED 8210 00 |
| Деталь: | CUSHION |
| Парткод: | A0P0 9008 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 8205 00 |
| Деталь: | SHAFT |
| Парткод: | 4025 5984 01 |
| Деталь: | BUSHING |
| Парткод: | A02E 8152 00 |
| Деталь: | Holding Part |
| Парткод: | A0ED 8151 00 |
| Деталь: | ROLL |
| Парткод: | 4497 3116 01 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 8211 00 |
| Деталь: | ACTUATOR |
| Парткод: | A0ED 8207 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 8202 01 |
| Деталь: | CUSHION |
| Парткод: | A0ED 8212 00 |
| Деталь: | Pulley 22T |
| Парткод: | A0ED 8117 00 |
| Деталь: | ROLL |
| Парткод: | A0ED 8142 00 |
| Деталь: | COVER |
| Парткод: | A0ED 8111 00 |
| Деталь: | GEAR 22T |
| Парткод: | A0ED 8137 00 |
| Деталь: | LEVER |
| Парткод: | A0ED 8144 00 |
| Деталь: | Coil spring |
| Парткод: | A0ED 8140 00 |
| Деталь: | Gear 22/23T |
| Парткод: | A0ED 8136 00 |
| Деталь: | TIMING BELT 270L |
| Парткод: | A0ED 8113 00 |
| Деталь: | Pulley 22T |
| Парткод: | A0ED 8141 00 |
| Деталь: | Caulking (Drive) |
| Парткод: | A0ED G811 00 |
| Деталь: | Vibrationproof Plate |
| Парткод: | A0ED 2742 00 |
| Деталь: | MIRROR |
| Парткод: | A0ED 2732 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2733 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED 2741 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 2816 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4036 1720 01 |
| Деталь: | LEVER |
| Парткод: | A00J 2802 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0903 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2801 00 |
| Деталь: | TAPE |
| Парткод: | 4036 3075 01 |
| Деталь: | REED SWITCH |
| Парткод: | 9334 2610 12 |
| Деталь: | BUSHING |
| Парткод: | A0ED 2710 00 |
| Деталь: | PULLEY |
| Парткод: | A0ED 2736 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2737 00 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 81 |
| Деталь: | Scanner Wiring /4 |
| Парткод: | A0ED N144 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 2812 00 |
| Деталь: | PULLEY |
| Парткод: | A0ED 2739 00 |
| Деталь: | GUIDE PART |
| Парткод: | A0ED 2740 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2811 00 |
| Деталь: | Scanner Wiring /3 |
| Парткод: | A0ED N143 01 |
| Деталь: | Scanner Wiring /1 |
| Парткод: | A0ED N141 00 |
| Деталь: | SPACER |
| Парткод: | V502 0100 33 |
| Деталь: | Scanner Wiring /6 |
| Парткод: | A0ED N146 00 |
| Деталь: | Inverter unit |
| Парткод: | A0ED M410 00 |
| Деталь: | PWB Assembly (PWB-IF ASSY) |
| Парткод: | A0ED H01A 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2734 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 2754 00 |
| Деталь: | PULLEY |
| Парткод: | A0ED 2753 01 |
| Деталь: | BEARING |
| Парткод: | A0ED 2765 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 2705 00 |
| Деталь: | SEAL |
| Парткод: | A02E 2708 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2704 00 |
| Деталь: | Pressing Plate |
| Парткод: | A0ED 2709 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2708 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED 2703 00 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 2763 00 |
| Деталь: | Pulling Spring |
| Парткод: | A0ED 2763 01 |
| Деталь: | MIRROR |
| Парткод: | A0ED 2702 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2707 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 2706 00 |
| Деталь: | Lamp |
| Парткод: | A0ED M310 00 |
| Деталь: | Stepping motor |
| Парткод: | A02E M10A 00 |
| Деталь: | Vibrationproof Rubber |
| Парткод: | A0P0 2767 00 |
| Деталь: | Belt 210L |
| Парткод: | A0ED 2756 00 |
| Деталь: | Pulley 117T |
| Парткод: | A0ED 2755 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2760 00 |
| Деталь: | Pulling Spring |
| Парткод: | A0ED 2757 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2762 00 |
| Деталь: | WIRE |
| Парткод: | A0ED 2751 00 |
| Деталь: | 1st Slider Assy |
| Парткод: | A0ED R728 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 1075 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1023 00 |
| Деталь: | Reinforce Nut |
| Парткод: | A0ED 1020 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1042 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 1019 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 1041 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1018 00 |
| Деталь: | Cover Lever |
| Парткод: | A0ED 1013 01 |
| Деталь: | LEVER |
| Парткод: | A0ED 1017 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1016 01 |
| Деталь: | ROLL |
| Парткод: | A0ED 6234 00 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996 3055 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1066 00 |
| Деталь: | RAIL |
| Парткод: | A0ED 1007 00 |
| Деталь: | M ounting Plate |
| Парткод: | A0ED 1065 00 |
| Деталь: | Scale |
| Парткод: | A02E 9408 00 |
| Деталь: | Scale |
| Парткод: | A02E 9409 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | A0ED 5922 01 |
| Деталь: | GEAR 20T |
| Парткод: | A02E 5921 00 |
| Деталь: | Caulking Gear Mounting Plate |
| Парткод: | A02E G621 00 |
| Деталь: | GEAR 40T |
| Парткод: | A02E 5983 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5981 00 |
| Деталь: | RESISTOR |
| Парткод: | V801 3000 06 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 5935 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0ED 5928 00 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 5936 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A02E 5925 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 5926 00 |
| Деталь: | Brake Part |
| Парткод: | A0ED 5931 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 5990 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5991 00 |
| Деталь: | Photoreflector |
| Парткод: | A0ED M501 00 |
| Деталь: | Sensor Wiring /2 |
| Парткод: | A0ED N10N 00 |
| Деталь: | SEAL |
| Парткод: | A02E 5937 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 5992 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4687 3281 01 |
| Деталь: | BRAKE |
| Парткод: | A02E 5934 00 |
| Деталь: | BRAKE |
| Парткод: | A02E 5932 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 5923 00 |
| Деталь: | BRAKE |
| Парткод: | A02E 5933 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 5924 00 |
| Деталь: | COVER |
| Парткод: | A0ED 5909 00 |
| Деталь: | Bypass Label |
| Парткод: | A0ED 9402 00 |
| Деталь: | TRAY |
| Парткод: | A02E 5911 00 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 5984 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 3446 01 |
| Деталь: | SHAFT |
| Парткод: | 1134 3042 02 |
| Деталь: | HOLDER |
| Парткод: | A0ED 5987 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Sensor Wiring /1 |
| Парткод: | A0ED N10M 01 |
| Деталь: | COVER |
| Парткод: | A02E 5918 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 5986 00 |
| Деталь: | TRAY |
| Парткод: | A0ED 5908 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A0ED 5939 00 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 5982 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3234 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | BRACKET |
| Парткод: | 9J06 3235 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5910 00 |
| Деталь: | Multiple Bypass Tray Assy |
| Парткод: | A0ED R729 00 |
| Деталь: | CONTACT |
| Парткод: | A0ED 1120 00 |
| Деталь: | Transfer Wiring /Y |
| Парткод: | A0ED N10U 01 |
| Деталь: | RAIL |
| Парткод: | A0ED 1102 00 |
| Деталь: | DETECTING PLATE |
| Парткод: | A0ED 1108 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED 1109 00 |
| Деталь: | Transfer Wiring /K |
| Парткод: | A0ED N10W 01 |
| Деталь: | Arm /Rear |
| Парткод: | A0ED 1106 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | Lever /Rear |
| Парткод: | A0ED 1107 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED 1110 00 |
| Деталь: | Torsion Coil spring /R |
| Парткод: | A0ED 1112 00 |
| Деталь: | Transfer Wiring /2 |
| Парткод: | A0ED N10X 00 |
| Деталь: | CONTACT |
| Парткод: | A0ED 1119 00 |
| Деталь: | Contact /K |
| Парткод: | A0ED 1114 00 |
| Деталь: | CONTACT |
| Парткод: | A0ED 1117 00 |
| Деталь: | Contact /Color |
| Парткод: | A0ED 1115 00 |
| Деталь: | CONTACT |
| Парткод: | A0ED 1118 00 |
| Деталь: | Intermediate Image Transfer Kit |
| Парткод: | A0ED R716 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5084 00 |
| Деталь: | Lever /Front |
| Парткод: | A0ED 1105 00 |
| Деталь: | Arm /Front |
| Парткод: | A0ED 1104 00 |
| Деталь: | Torsion Coil spring /F |
| Парткод: | A0ED 1111 00 |
| Деталь: | RAIL |
| Парткод: | A0ED 1101 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Connecting Detection harness |
| Парткод: | A0ED N10B 01 |
| Деталь: | RAIL |
| Парткод: | A0ED 1103 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1121 00 |
| Деталь: | SHIELD PLATE |
| Парткод: | A0ED 1375 00 |
| Деталь: | SHIELD PLATE |
| Парткод: | A0ED 1323 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1473 00 |
| Деталь: | CUSHION |
| Парткод: | 4004 1829 02 |
| Деталь: | GROUND PLATE |
| Парткод: | A0P0 1459 00 |
| Деталь: | MEMORY MODULES |
| Парткод: | V865 3000 26 |
| Деталь: | Controller Detection harness |
| Парткод: | A0ED N116 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1449 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | RAIL |
| Парткод: | A0P0 1447 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1322 00 |
| Деталь: | SCREW |
| Парткод: | 4025 2283 01 |
| Деталь: | COVER |
| Парткод: | A0ED 1372 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1472 01 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 1373 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A02E 1933 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1474 01 |
| Деталь: | COVER |
| Парткод: | A00J 1387 00 |
| Деталь: | SCREW |
| Парткод: | A00J 1396 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 1320 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1319 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1371 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0ED 1325 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 1401 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 1358 00 |
| Деталь: | PIN |
| Парткод: | A0ED 1314 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1313 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1315 01 |
| Деталь: | LABEL |
| Парткод: | 9J06 7301 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1357 00 |
| Деталь: | Power Supply Wiring |
| Парткод: | A02E N125 01 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 1374 00 |
| Деталь: | SHEET |
| Парткод: | A0ED 1328 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1312 00 |
| Деталь: | GUIDE RAIL |
| Парткод: | A00J 1367 00 |
| Деталь: | Shield Case |
| Парткод: | A0ED 1311 01 |
| Деталь: | ImageProcessing Flatcable /25 |
| Парткод: | A0ED N113 00 |
| Деталь: | SUPPORT |
| Парткод: | V502 0100 26 |
| Деталь: | PWB Assembly(PWB-EE ASSY) |
| Парткод: | A0P0 H00C 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 1376 00 |
| Деталь: | PWB Assembly(PWB-MC ASSY) |
| Парткод: | A0ED H001 03 |
| Деталь: | ImageProcessing Flatcable /30 |
| Парткод: | A0ED N114 00 |
| Деталь: | HDD |
| Парткод: | A0ED M720 00 |
| Деталь: | CABLE |
| Парткод: | A0P0 N152 00 |
| Деталь: | CABLE |
| Парткод: | A0P0 N151 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1324 00 |
| Деталь: | PWB assembly(PWB-PCI ASSY) |
| Парткод: | A0P0 H026 01 |
| Деталь: | FERRITECORE |
| Парткод: | A0P0 M900 00 |
| Деталь: | PWB Assembly(PWB-MFP ASSY) |
| Парткод: | A0ED H020 02 |
| Деталь: | PWB Assembly(PWB-MFP ASSY) |
| Парткод: | A0ED H021 02 |
| Деталь: | Power source Cord /100V |
| Парткод: | A0ED N300 01 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 1377 00 |
| Деталь: | LIFTING PLATE |
| Парткод: | A0ED 6205 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030 3226 01 |
| Деталь: | Caulking(Regulating Plate/ASSY) |
| Парткод: | A0ED F621 00 |
| Деталь: | KNOB |
| Парткод: | 4037 3204 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3021 01 |
| Деталь: | LEVER |
| Парткод: | A0ED 6213 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED 6214 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 6202 00 |
| Деталь: | Rack /Front |
| Парткод: | A0ED 6211 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3206 01 |
| Деталь: | BUSHING |
| Парткод: | 0992 3014 01 |
| Деталь: | Paper feed Cassette |
| Парткод: | A0ED 6301 02 |
| Деталь: | Label Cd |
| Парткод: | A00J 9421 02 |
| Деталь: | Label FD |
| Парткод: | A00J 9423 02 |
| Деталь: | Label FD |
| Парткод: | A00J 9422 02 |
| Деталь: | GEAR 14T |
| Парткод: | A02E 6224 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0ED 6206 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3228 12 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 6223 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 6216 00 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3207 01 |
| Деталь: | BUSHING |
| Парткод: | A0ED 6204 00 |
| Деталь: | CUSHION |
| Парткод: | A02E 6233 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LABEL CARRYING CAPACITY |
| Парткод: | 4002 7306 01 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A0ED 6209 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 6210 00 |
| Деталь: | CUSHION |
| Парткод: | A02E 6227 00 |
| Деталь: | GUIDE |
| Парткод: | 4537 3317 01 |
| Деталь: | Caulking(Mounting Plate cassette) |
| Парткод: | A0ED F622 00 |
| Деталь: | REGULATING PLATE ASSY |
| Парткод: | A02E R734 00 |
| Деталь: | 2nd Cassette Assy |
| Парткод: | A0ED R736 11 |
| Деталь: | ROLL |
| Парткод: | A0ED 6234 00 |
| Деталь: | Reinforce Plate /Right rear |
| Парткод: | A0ED 6231 00 |
| Деталь: | LOCK LEVER |
| Парткод: | A0ED 6255 00 |
| Деталь: | Release Lever |
| Парткод: | A0ED 6257 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED 6258 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 6353 01 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED 6254 00 |
| Деталь: | LABEL PAPER |
| Парткод: | A0ED 9401 00 |
| Деталь: | COVER |
| Парткод: | A0ED 6351 02 |
| Деталь: | HANDLE |
| Парткод: | A0ED 6252 01 |
| Деталь: | COVER |
| Парткод: | A0ED 6250 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 6219 01 |
| Деталь: | LEVER |
| Парткод: | A02E 6214 00 |
| Деталь: | STOPPER |
| Парткод: | A0ED 6242 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 6241 00 |
| Деталь: | Reinforce Plate /Left rear |
| Парткод: | A0ED 6232 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 6221 00 |
| Деталь: | Read Cover |
| Парткод: | A0ED 1714 01 |
| Деталь: | Label Emperon |
| Парткод: | A011 9462 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M705 01 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M706 01 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M707 01 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M708 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M709 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1694 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1679 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1915 00 |
| Деталь: | WASHER |
| Парткод: | A00J 1929 00 |
| Деталь: | LEVER |
| Парткод: | A0ED 1922 00 |
| Деталь: | Pulling Spring |
| Парткод: | A0ED 1926 00 |
| Деталь: | HANDLE |
| Парткод: | A0ED 1925 01 |
| Деталь: | LEVER |
| Парткод: | A0ED 1923 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1921 00 |
| Деталь: | WASHER |
| Парткод: | A00J 1919 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1912 00 |
| Деталь: | Support Screw |
| Парткод: | A00J 1918 00 |
| Деталь: | Read Cover |
| Парткод: | A0ED 1716 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1680 00 |
| Деталь: | Support Shaft |
| Парткод: | A00J 1928 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1916 00 |
| Деталь: | ARM |
| Парткод: | A0P0 1913 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A0P0 1927 01 |
| Деталь: | COLLAR |
| Парткод: | A00J 1917 00 |
| Деталь: | ARM |
| Парткод: | A0P0 1914 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1911 00 |
| Деталь: | Read Cover /Right front |
| Парткод: | A0ED 1710 01 |
| Деталь: | Ope.unit Cable |
| Парткод: | A0ED N11B 01 |
| Деталь: | Mounting Plate (Control Panel) Assy |
| Парткод: | A0ED R702 00 |
| Деталь: | Pen |
| Парткод: | A0PD 1602 00 |
| Деталь: | Read Cover /Right rear |
| Парткод: | A0ED 1705 00 |
| Деталь: | COVER |
| Парткод: | A02E 1677 00 |
| Деталь: | Read Cover /Right |
| Парткод: | A0ED 1704 01 |
| Деталь: | COVER |
| Парткод: | A00J 1691 00 |
| Деталь: | Read Cover F |
| Парткод: | A0ED 1711 00 |
| Деталь: | Read Cover |
| Парткод: | A0ED 1715 00 |
| Деталь: | Read Cover |
| Парткод: | A0ED 1712 00 |
| Деталь: | Scanner Wiring /7 |
| Парткод: | A0ED N147 00 |
| Деталь: | Read Cover Upper F |
| Парткод: | A0ED 1706 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 1692 00 |
| Деталь: | Read Cover /Front |
| Парткод: | A0ED 1701 00 |
| Деталь: | Light blocking Plate |
| Парткод: | A00J 1689 02 |
| Деталь: | Lens /B |
| Парткод: | A00J 1682 02 |
| Деталь: | Light blocking Cover /C |
| Парткод: | A00J 1685 02 |
| Деталь: | PWB Assembly LED2 |
| Парткод: | A00J H00E 00 |
| Деталь: | Scanner Wiring /5 |
| Парткод: | A0ED N145 00 |
| Деталь: | Read Cover /Left |
| Парткод: | A0ED 1703 00 |
| Деталь: | Read Cover /Rear |
| Парткод: | A0ED 1702 00 |
| Деталь: | Read Cover Upper R |
| Парткод: | A0ED 1707 00 |
| Деталь: | Label Print Side |
| Парткод: | A0ED 9403 00 |
| Деталь: | Label Legal Restiriction |
| Парткод: | A00J 9401 00 |
| Деталь: | LABEL |
| Парткод: | A00J 9402 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 6277 00 |
| Деталь: | MOTOR |
| Парткод: | 9J06 M103 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED 6276 00 |
| Деталь: | HOLDER |
| Парткод: | 4030 3083 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030 3224 02 |
| Деталь: | Paperfeed Wiring /Rear |
| Парткод: | A0ED N10E 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 6275 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4002 3110 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4002 3131 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3091 01 |
| Деталь: | PWB ASSY |
| Парткод: | 4037 0104 01 |
| Деталь: | HOLDER |
| Парткод: | 4011 3012 01 |
| Деталь: | Cover Output |
| Парткод: | A0ED 8901 00 |
| Деталь: | Label Output |
| Парткод: | A0ED 9404 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | A02E 8907 00 |
| Деталь: | SHEET |
| Парткод: | A0ED 8971 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | FAN MOTOR |
| Парткод: | A0ED M105 00 |
| Деталь: | Cooling Wiring /1 |
| Парткод: | A0ED N10H 00 |
| Деталь: | DUCT |
| Парткод: | A0ED 8908 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 8970 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 8904 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 5896 02 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 8905 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0ED 8963 00 |
| Деталь: | LEVER |
| Парткод: | A0ED 8956 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 8964 00 |
| Деталь: | BUSHING |
| Парткод: | A0ED 8911 00 |
| Деталь: | SHAFT |
| Парткод: | 4025 5984 01 |
| Деталь: | POSITIONING PLATE |
| Парткод: | A0ED 8969 00 |
| Деталь: | ROLL |
| Парткод: | 4004 5903 01 |
| Деталь: | COLLAR |
| Парткод: | 4139 5577 01 |
| Деталь: | PIN |
| Парткод: | 4036 2549 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 8906 00 |
| Деталь: | ROLLER |
| Парткод: | A0ED 8910 00 |
| Деталь: | PULLEY 28T |
| Парткод: | A0ED 8952 00 |
| Деталь: | Timing belt 160L |
| Парткод: | A0ED 8967 00 |
| Деталь: | Stepping motor |
| Парткод: | A0ED M103 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0ED 8902 00 |
| Деталь: | Label Toner 2 |
| Парткод: | A0ED 9407 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 4056 01 |
| Деталь: | SUCTION PLATE |
| Парткод: | A0ED 4057 00 |
| Деталь: | SPACER |
| Парткод: | A0ED 4055 01 |
| Деталь: | Label Toner 1 |
| Парткод: | A0ED 9406 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 4054 00 |
| Деталь: | DETECTING PLATE |
| Парткод: | A0ED 4053 00 |
| Деталь: | COVER |
| Парткод: | A0ED 4051 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 4026 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 4009 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 4008 01 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038 1014 01 |
| Деталь: | HOLD PLATE |
| Парткод: | A0ED 2452 00 |
| Деталь: | GEAR 16T |
| Парткод: | A0ED 2579 00 |
| Деталь: | Gear 32/16T |
| Парткод: | A0ED 2454 00 |
| Деталь: | Gear 40/20T |
| Парткод: | A0ED 2451 00 |
| Деталь: | Gear 20/20T |
| Парткод: | A0ED 2450 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 2586 01 |
| Деталь: | COVER |
| Парткод: | A0ED 4050 00 |
| Деталь: | COVER |
| Парткод: | A0ED 4060 00 |
| Деталь: | COVER |
| Парткод: | A0ED 4061 00 |
| Деталь: | COVER |
| Парткод: | A0ED 4062 00 |
| Деталь: | COVER |
| Парткод: | A0ED 4063 00 |
| Деталь: | COVER |
| Парткод: | A0ED 4064 00 |
| Деталь: | COVER |
| Парткод: | A0ED 4065 00 |
| Деталь: | COVER |
| Парткод: | A0ED 4066 00 |
| Деталь: | WASTE TONER DRIVE ASSY |
| Парткод: | A0ED R707 00 |
| Деталь: | Sub Hopper Assy(Amur1JP) |
| Парткод: | A0ED R710 00 |
| Деталь: | Sub Hopper Assy(Amur1US) |
| Парткод: | A0ED R711 00 |
| Деталь: | Sub Hopper Assy(Amur1EU) |
| Парткод: | A0ED R712 00 |
| Деталь: | Sub Hopper Assy(Amur2/3JP) |
| Парткод: | A0ED R713 00 |
| Деталь: | Sub Hopper Assy(Amur2/3US) |
| Парткод: | A0ED R714 00 |
| Деталь: | Sub Hopper Assy(Amur2/3EU) |
| Парткод: | A0ED R715 00 |
| Деталь: | Sub Hopper Assy(Amur1 other) |
| Парткод: | A0ED R737 00 |
| Деталь: | Sub Hopper(Amur2/3 Others) |
| Парткод: | A0ED R739 00 |
| Деталь: | Gear 47T |
| Парткод: | A0ED 4021 00 |
| Деталь: | GEAR 19T |
| Парткод: | A0ED 4019 00 |
| Деталь: | Gear 23T |
| Парткод: | A0ED 4020 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 4016 00 |
| Деталь: | SPRING |
| Парткод: | 4038 5411 01 |
| Деталь: | GEAR 36T |
| Парткод: | A0ED 4015 00 |
| Деталь: | BUSHING |
| Парткод: | 4163 5102 01 |
| Деталь: | GEAR 40T |
| Парткод: | A0ED 4018 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 4028 01 |
| Деталь: | Gear 37/37T |
| Парткод: | A0ED 4025 00 |
| Деталь: | Gear 37/88T |
| Парткод: | A0ED 4017 00 |
| Деталь: | MAGNET |
| Парткод: | 9326 2900 06 |
| Деталь: | DETECTING PLATE |
| Парткод: | A0ED 4005 00 |
| Деталь: | PIN |
| Парткод: | A0ED 4006 00 |
| Деталь: | Agitating Shaft |
| Парткод: | A0ED 4003 00 |
| Деталь: | Agitating Part |
| Парткод: | A0ED 4004 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 4024 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 4023 00 |
| Деталь: | Stepping motor |
| Парткод: | A02E M104 00 |
| Деталь: | SWITCH |
| Парткод: | 9334 2710 11 |
| Деталь: | PLATE NUT |
| Парткод: | 4011 5339 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4036 5348 01 |
| Деталь: | SHUTTER |
| Парткод: | A0ED 4010 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 4011 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 4007 00 |
| Деталь: | Gear 33T |
| Парткод: | A0ED 4013 00 |
| Деталь: | Gear 20/51T |
| Парткод: | A0ED 4014 00 |
| Деталь: | Supply Roller |
| Парткод: | A0ED 4002 01 |
| Деталь: | GEAR 17T |
| Парткод: | A0ED 4012 00 |
| Деталь: | Toner Drive harness |
| Парткод: | A0ED N108 01 |
| Деталь: | DUCT |
| Парткод: | A0ED 1420 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | Cooling Wiring /2 |
| Парткод: | A0ED N10J 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1081 00 |
| Деталь: | Print Head Assy(Amur1/2) |
| Парткод: | A0ED R708 00 |
| Деталь: | Print Head Assy(Amur3) |
| Парткод: | A0ED R709 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1028 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 1026 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1459 00 |
| Деталь: | KNOB |
| Парткод: | A00J 3650 01 |
| Деталь: | Fixing Plate |
| Парткод: | A0ED 3603 01 |
| Деталь: | POSITIONING PLATE |
| Парткод: | A0ED 1022 00 |
| Деталь: | PIN |
| Парткод: | A0ED 1032 01 |
| Деталь: | PIN |
| Парткод: | A0ED 1031 00 |
| Деталь: | PIN |
| Парткод: | A0ED 1021 00 |
| Деталь: | RAIL |
| Парткод: | A0ED 1076 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0ED 1074 00 |
| Деталь: | PIPE |
| Парткод: | A0ED 3630 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 3634 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED 3632 00 |
| Деталь: | SHUTTER |
| Парткод: | A0ED 3631 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 3633 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1087 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1088 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1084 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1085 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1086 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1093 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1012 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1011 00 |
| Деталь: | Waste Toner Pipe |
| Парткод: | A0ED F360 00 |
| Деталь: | LIFTING PLATE |
| Парткод: | A0ED 6205 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030 3226 01 |
| Деталь: | Caulking(Regulating Plate/ASSY) |
| Парткод: | A0ED F621 00 |
| Деталь: | KNOB |
| Парткод: | 4037 3204 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3021 01 |
| Деталь: | LEVER |
| Парткод: | A0ED 6213 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED 6214 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 6202 00 |
| Деталь: | Rack /Front |
| Парткод: | A0ED 6211 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3206 01 |
| Деталь: | BUSHING |
| Парткод: | 0992 3014 01 |
| Деталь: | Paper feed Cassette |
| Парткод: | A0ED 6201 02 |
| Деталь: | Label Cd |
| Парткод: | A02E 9415 00 |
| Деталь: | Label FD |
| Парткод: | A02E 9413 00 |
| Деталь: | Label FD |
| Парткод: | A00J 9422 02 |
| Деталь: | GEAR 14T |
| Парткод: | A02E 6224 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0ED 6206 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3228 12 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 6223 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 6216 00 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3207 01 |
| Деталь: | BUSHING |
| Парткод: | A0ED 6204 00 |
| Деталь: | CUSHION |
| Парткод: | A02E 6233 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LABEL CARRYING CAPACITY |
| Парткод: | 4002 7306 01 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A0ED 6209 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 6210 00 |
| Деталь: | CUSHION |
| Парткод: | A02E 6227 00 |
| Деталь: | GUIDE |
| Парткод: | 4537 3317 01 |
| Деталь: | Caulking(Mounting Plate cassette) |
| Парткод: | A0ED F622 00 |
| Деталь: | REGULATING PLATE ASSY |
| Парткод: | A02E R734 00 |
| Деталь: | 1st Cassette Assy |
| Парткод: | A0ED R735 11 |
| Деталь: | ROLL |
| Парткод: | A0ED 6234 00 |
| Деталь: | Reinforce Plate /Right rear |
| Парткод: | A0ED 6231 00 |
| Деталь: | LOCK LEVER |
| Парткод: | A0ED 6255 00 |
| Деталь: | Release Lever |
| Парткод: | A0ED 6257 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED 6258 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 6253 01 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED 6254 00 |
| Деталь: | LABEL PAPER |
| Парткод: | A0ED 9401 00 |
| Деталь: | COVER |
| Парткод: | A0ED 6251 02 |
| Деталь: | HANDLE |
| Парткод: | A0ED 6252 01 |
| Деталь: | COVER |
| Парткод: | A0ED 6250 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 6219 01 |
| Деталь: | LEVER |
| Парткод: | 4002 3108 01 |
| Деталь: | STOPPER |
| Парткод: | A0ED 6242 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 6241 00 |
| Деталь: | Reinforce Plate /Left rear |
| Парткод: | A0ED 6232 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 6221 00 |
| Деталь: | Scanner Relay harness /100V |
| Парткод: | A0ED N11C 00 |
| Деталь: | Heater Relay harness |
| Парткод: | A0ED N103 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 1367 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 2287 02 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06 M601 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1056 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1361 00 |
| Деталь: | PWB Assembly (PWB-F ASSY) |
| Парткод: | A0ED H003 00 |
| Деталь: | SEESAW-SWITCH |
| Парткод: | 4038 M600 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1351 00 |
| Деталь: | PWB-PH Assembly(PWB-PH ASSY) |
| Парткод: | A0ED H002 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1303 00 |
| Деталь: | Power supply /100V |
| Парткод: | A0ED M403 00 |
| Деталь: | Power supply /230V |
| Парткод: | A0ED M401 01 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED 1037 00 |
| Деталь: | Slide Lever |
| Парткод: | A0ED 1036 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1050 00 |
| Деталь: | PIN |
| Парткод: | 9752 3012 50 |
| Деталь: | Support Holder |
| Парткод: | A0ED 1060 00 |
| Деталь: | RAIL |
| Парткод: | A0ED 1006 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 1057 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1048 01 |
| Деталь: | Relay Connector |
| Парткод: | A0ED M600 01 |
| Деталь: | LEVER |
| Парткод: | A0ED 1034 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED 1052 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0ED 1053 00 |
| Деталь: | FILTER |
| Парткод: | A0ED 1409 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | DUCT |
| Парткод: | A0ED 1410 00 |
| Деталь: | LEVER |
| Парткод: | A0ED 1058 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 1033 00 |
| Деталь: | Photoconductor Wiring /C |
| Парткод: | A0ED N10P 01 |
| Деталь: | Photoconductor Wiring /K |
| Парткод: | A0ED N117 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1090 01 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1067 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1068 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1069 00 |
| Деталь: | PAD |
| Парткод: | A0ED 1070 00 |
| Деталь: | STAY |
| Парткод: | A0ED 1071 00 |
| Деталь: | STAY |
| Парткод: | A0ED 1072 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1083 00 |
| Деталь: | KNOB |
| Парткод: | A0ED 1082 00 |
| Деталь: | Light blocking Part |
| Парткод: | A0ED 1055 00 |
| Деталь: | RAIL |
| Парткод: | A0ED 1043 01 |
| Деталь: | Neutralizing LED array |
| Парткод: | A0ED M304 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1073 00 |
| Деталь: | RAIL |
| Парткод: | A0ED 1005 01 |
| Деталь: | RAIL |
| Парткод: | A0ED 1054 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1089 00 |
| Деталь: | Eraser (Black) Assy |
| Парткод: | A0ED R700 00 |
| Деталь: | Eraser (YMC) Assy |
| Парткод: | A0ED R701 00 |
| Деталь: | Gear 50/28T |
| Парткод: | A0ED 2544 00 |
| Деталь: | Gear 52/17T |
| Парткод: | A0ED 2542 00 |
| Деталь: | Gear 72/24T |
| Парткод: | A0ED 2570 00 |
| Деталь: | Gear 17/48T |
| Парткод: | A0ED 2543 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 2582 00 |
| Деталь: | GEAR 34T |
| Парткод: | A02E 2571 00 |
| Деталь: | PIN |
| Парткод: | 9752 3012 50 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 02 |
| Деталь: | Gear 39T |
| Парткод: | A0ED 2545 00 |
| Деталь: | PIN |
| Парткод: | 9752 2016 50 |
| Деталь: | HOLDER |
| Парткод: | A0ED 2557 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 2573 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 2563 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 2596 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 2587 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A0ED 2312 00 |
| Деталь: | GEAR 16T |
| Парткод: | 9J06 2574 01 |
| Деталь: | GEAR 13T |
| Парткод: | A0ED 2546 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2576 00 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2580 01 |
| Деталь: | GEAR 26T |
| Парткод: | A0ED 2575 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 2594 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 2595 00 |
| Деталь: | GEAR 41T |
| Парткод: | 4038 2593 02 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2592 01 |
| Деталь: | CLUTCH |
| Парткод: | A02E M200 00 |
| Деталь: | GEAR 29T |
| Парткод: | A0ED 2591 01 |
| Деталь: | LEVER |
| Парткод: | A0ED 2584 01 |
| Деталь: | WASHER |
| Парткод: | A02E 2302 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A02E 2585 00 |
| Деталь: | WASHER |
| Парткод: | A02E 2303 00 |
| Деталь: | BUSHING |
| Парткод: | 9J06 2101 00 |
| Деталь: | CONNECTOR |
| Парткод: | V651 0100 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2556 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | DC Brushless motor |
| Парткод: | A0ED M101 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2310 00 |
| Деталь: | Fuser Pressure Release motor Assy |
| Парткод: | A0ED R723 00 |
| Деталь: | FUSER DRIVE ASSY |
| Парткод: | A0ED R703 00 |
| Деталь: | DRIVE ROLLER |
| Парткод: | A0ED 5781 00 |
| Деталь: | Photoreflector |
| Парткод: | A0ED M501 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5711 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | Frame /Front |
| Парткод: | A0ED 5701 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | Paperfeed Wiring /2 |
| Парткод: | A0ED N10G 01 |
| Деталь: | Paperfeed Wiring /2 |
| Парткод: | A0ED N11E 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5609 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 5612 00 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3016 12 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E 5611 00 |
| Деталь: | GEAR 30T |
| Парткод: | 4425 3013 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | GEAR 29T |
| Парткод: | 4030 3008 01 |
| Деталь: | Paper feed Holder |
| Парткод: | A00J 5601 00 |
| Деталь: | SHAFT |
| Парткод: | 4040 3097 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5603 02 |
| Деталь: | Shaft /P |
| Парткод: | A00J 5640 00 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5668 01 |
| Деталь: | LEVER |
| Парткод: | A02E 5613 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 5608 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 5605 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M202 00 |
| Деталь: | Gear 26/36T |
| Парткод: | A0ED 5661 00 |
| Деталь: | Caulking (Mounting Plate Drive Rein force |
| Парткод: | A0ED G571 00 |
| Деталь: | GEAR 22T |
| Парткод: | A02E 5954 00 |
| Деталь: | Gear 26/35T |
| Парткод: | A0ED 5662 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M200 00 |
| Деталь: | COVER |
| Парткод: | A0ED 5790 00 |
| Деталь: | Paper Feed Assy (2nd) |
| Парткод: | A0ED R733 00 |
| Деталь: | Paper Feed Assy (2nd)3 |
| Парткод: | A0ED R734 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0ED 5784 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5785 00 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3125 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5612 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0ED 5782 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 5843 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5636 00 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A02E F566 00 |
| Деталь: | LEVER |
| Парткод: | 4030 3078 01 |
| Деталь: | HOLDER |
| Парткод: | 4030 3013 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3017 03 |
| Деталь: | BRACKET |
| Парткод: | 4030 3014 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 5610 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5638 00 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A02E R729 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1603 00 |
| Деталь: | LABEL |
| Парткод: | A0ED 9465 00 |
| Деталь: | Indicating Wiring |
| Парткод: | A0ED N10C 00 |
| Деталь: | PWB Assembly LED1 |
| Парткод: | A00J H00D 00 |
| Деталь: | Light blocking Cover |
| Парткод: | A00J 1683 00 |
| Деталь: | Light blocking Plate |
| Парткод: | A0ED 1627 00 |
| Деталь: | LENS |
| Парткод: | A0ED 1626 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1604 00 |
| Деталь: | Label Number 1 |
| Парткод: | A02E 9418 00 |
| Деталь: | Label Number 2 |
| Парткод: | A02E 9419 00 |
| Деталь: | Label Toner 3 |
| Парткод: | A0ED 9408 00 |
| Деталь: | Label Toner 3 |
| Парткод: | A0ED 9409 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 1632 00 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475 2603 02 |
| Деталь: | Label bizhub C360 |
| Парткод: | A0ED 9418 00 |
| Деталь: | Label bizhub C280 |
| Парткод: | A0ED 9419 00 |
| Деталь: | Label bizhub C220 |
| Парткод: | A0ED 9420 00 |
| Деталь: | Open/close Cover /Front |
| Парткод: | A0ED 1602 01 |
| Деталь: | Logo Mark |
| Парткод: | A00J 9455 00 |
| Деталь: | Label Replace |
| Парткод: | A0ED 9405 02 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | COVER |
| Парткод: | A0ED 3618 01 |
| Деталь: | BAND |
| Парткод: | A0ED 1624 01 |
| Деталь: | CONTACT |
| Парткод: | A0ED 1675 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1673 01 |
| Деталь: | PROTECTION PART |
| Парткод: | A0ED 1674 00 |
| Деталь: | Label DR Y |
| Парткод: | A0ED 9411 00 |
| Деталь: | Label DR M |
| Парткод: | A0ED 9412 00 |
| Деталь: | Label DR C |
| Парткод: | A0ED 9413 00 |
| Деталь: | Label DR K |
| Парткод: | A0ED 9414 00 |
| Деталь: | Cover (2nd Front) |
| Парткод: | A0ED F164 02 |
| Деталь: | Read Cover /Rear |
| Парткод: | A0ED 1622 00 |
| Деталь: | Read Cover /Rear |
| Парткод: | A0ED 1628 00 |
| Деталь: | TRAY |
| Парткод: | A0ED 1610 01 |
| Деталь: | Cover /Upper |
| Парткод: | A0ED 1601 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1630 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1616 00 |
| Деталь: | Cover /Left |
| Парткод: | A0ED 1607 00 |
| Деталь: | Cover /Left |
| Парткод: | A0ED 1608 00 |
| Деталь: | COVER REAR UPPER |
| Парткод: | A0ED 1621 00 |
| Деталь: | Read Cover |
| Парткод: | A0ED 1623 00 |
| Деталь: | Cover Right Rear |
| Парткод: | A0ED 1618 01 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 1617 02 |
| Деталь: | Cover Right Open |
| Парткод: | A0ED 1609 03 |
| Деталь: | COVER |
| Парткод: | A0ED 1629 01 |
| Деталь: | COVER |
| Парткод: | A0ED 1612 01 |
| Деталь: | Cover Rear R |
| Парткод: | A0ED 1606 01 |
| Деталь: | Cover Rear L |
| Парткод: | A0ED 1605 00 |
| Деталь: | Label 220-240V 0.65A |
| Парткод: | A00J 9452 01 |
| Деталь: | LABEL |
| Парткод: | A02E 1499 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1662 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1625 00 |
| Деталь: | Label Only connect |
| Парткод: | A00J 9450 00 |
| Деталь: | LABEL CAUTION |
| Парткод: | A00J 9457 00 |
| Деталь: | Installing Spacer |
| Парткод: | A0ED 1661 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0ED 1063 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1402 01 |
| Деталь: | FILTER |
| Парткод: | A0ED 1403 00 |
| Деталь: | DUCT |
| Парткод: | A0ED 1400 00 |
| Деталь: | FAN MOTOR |
| Парткод: | A0ED M105 00 |
| Деталь: | Adjusting Plate |
| Парткод: | A0ED 1029 00 |
| Деталь: | SHAFT |
| Парткод: | A0ED 1019 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 1041 00 |
| Деталь: | Adjusting Plate |
| Парткод: | A0ED 1030 00 |
| Деталь: | Cover Lever |
| Парткод: | A0ED 1014 01 |
| Деталь: | COVER |
| Парткод: | A0ED 1064 00 |
| Деталь: | LEVER |
| Парткод: | A0ED 1017 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1040 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1038 01 |
| Деталь: | Adjusting Plate |
| Парткод: | A0ED 1039 00 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996 3055 01 |
| Деталь: | RAIL |
| Парткод: | A0ED 1077 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1062 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1079 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 1027 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0ED 1080 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1061 00 |
| Деталь: | COVER |
| Парткод: | A0ED 1078 00 |
| Деталь: | COVER |
| Парткод: | A0ED 7036 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 7016 00 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A0ED 7025 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0ED 7026 00 |
| Деталь: | Conveyance Wiring |
| Парткод: | A0ED N10A 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED 7024 00 |
| Деталь: | CONTACT |
| Парткод: | A0ED 7018 00 |
| Деталь: | ACTUATOR |
| Парткод: | 9J06 3563 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Sensor Wiring /3 |
| Парткод: | A0ED N115 00 |
| Деталь: | SHAFT |
| Парткод: | 9J06 3573 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3564 02 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED 7019 00 |
| Деталь: | FIXED POWER RESISTORS |
| Парткод: | V800 5003 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED 7020 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED 7017 00 |
| Деталь: | PIN |
| Парткод: | A0ED 7022 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 7015 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | Transfer Holder /2 |
| Парткод: | A0ED 5515 00 |
| Деталь: | Compressing Coil spring /2 |
| Парткод: | A0ED 5510 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 3511 02 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED 5511 00 |
| Деталь: | Transfer Holder /2 |
| Парткод: | A0ED 5507 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5509 00 |
| Деталь: | Guide Seal |
| Парткод: | A0ED 5517 00 |
| Деталь: | Neutralizing Part |
| Парткод: | A0ED 5508 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5516 00 |
| Деталь: | 2nd Image Transfer Rollor Assy |
| Парткод: | A0ED R717 00 |
| Деталь: | Vertical Transport Assy |
| Парткод: | A0ED R718 00 |
| Деталь: | ROLLER |
| Парткод: | A0ED 8106 00 |
| Деталь: | ROLL |
| Парткод: | 4497 3116 01 |
| Деталь: | BUSHING |
| Парткод: | A02E 8152 00 |
| Деталь: | MEMBER |
| Парткод: | 4066 3751 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED 8123 00 |
| Деталь: | Label JAM |
| Парткод: | A02E 9414 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 7010 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 7013 01 |
| Деталь: | SHEET |
| Парткод: | A0ED 7035 00 |
| Деталь: | Stepping motor |
| Парткод: | A0ED M102 00 |
| Деталь: | Caulking (Mounting Plate ADU) |
| Парткод: | A0ED G700 00 |
| Деталь: | Gear 22/26T |
| Парткод: | A0ED 8132 00 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 8130 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 8131 00 |
| Деталь: | Pulley 22T |
| Парткод: | A0ED 8117 00 |
| Деталь: | Gear 22/23T |
| Парткод: | A0ED 8118 00 |
| Деталь: | Timing Belt 316L |
| Парткод: | A0ED 8114 00 |
| Деталь: | COLLAR |
| Парткод: | A0ED 8119 00 |
| Деталь: | COVER |
| Парткод: | A0ED 7033 00 |
| Деталь: | Support Plate |
| Парткод: | A0ED 7068 00 |
| Деталь: | Support Plate |
| Парткод: | A0ED 7067 00 |
| Деталь: | Label Jam/M1 |
| Парткод: | A02E 9406 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 7129 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 7128 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 3539 01 |
| Деталь: | ROLLER |
| Парткод: | A0ED 7001 00 |
| Деталь: | ROLLER |
| Парткод: | A0ED 7002 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 3540 03 |
| Деталь: | SHEET |
| Парткод: | A0ED 7030 00 |
| Деталь: | Guide Sheet |
| Парткод: | A0ED 7006 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 7130 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 7023 00 |
| Деталь: | BUSHING |
| Парткод: | 4025 3572 01 |
| Деталь: | GEAR 20T |
| Парткод: | A0ED 7003 00 |
| Деталь: | GEAR 14T |
| Парткод: | A0ED 7007 00 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 3525 01 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0ED 7032 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 7057 01 |
| Деталь: | Toner Detection harness |
| Парткод: | A0ED N106 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 7029 00 |
| Деталь: | Photo sensing |
| Парткод: | A0ED M500 00 |
| Деталь: | ACTUATOR |
| Парткод: | A0ED 7037 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 1164 3527 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | CONVEYANCE SOLENOID |
| Парткод: | A034 M201 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0ED 7004 00 |
| Деталь: | LEVER |
| Парткод: | A0ED 7059 00 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A034 M500 00 |
| Деталь: | Holding Shutter |
| Парткод: | A0ED 7060 00 |
| Деталь: | Pulling Spring |
| Парткод: | A0ED 7028 00 |
| Деталь: | COVER |
| Парткод: | A0ED 7058 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M200 00 |
| Деталь: | SHEET |
| Парткод: | A0ED 7031 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 3537 01 |
| Деталь: | SPACER |
| Парткод: | 4038 3597 01 |
| Деталь: | HIGH VOLTAGE UNIT |
| Парткод: | A0ED M402 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1335 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1350 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1330 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1435 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 1434 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 1436 01 |
| Деталь: | DUCT |
| Парткод: | A0ED 1430 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 1458 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1431 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1173 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1334 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 1346 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 1336 00 |
| Деталь: | OZONE FILTER |
| Парткод: | A02E R727 00 |
| Деталь: | Stepping motor |
| Парткод: | A0ED M104 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 2401 00 |
| Деталь: | Gear 106/28T |
| Парткод: | A0ED 2403 00 |
| Деталь: | Gear 37/92T |
| Парткод: | A0ED 2404 00 |
| Деталь: | Gear 33T |
| Парткод: | A0ED 2405 00 |
| Деталь: | GEAR 37T |
| Парткод: | A0ED 2406 00 |
| Деталь: | SPRING |
| Парткод: | A0ED 2411 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 5412 02 |
| Деталь: | JOINT |
| Парткод: | A0ED 2407 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 2408 00 |
| Деталь: | COLLAR |
| Парткод: | 4038 5407 01 |
| Деталь: | DUCT |
| Парткод: | A0ED 1411 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1422 01 |
| Деталь: | DUCT |
| Парткод: | A0ED 1451 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 1454 01 |
| Деталь: | DUCT |
| Парткод: | A0ED 1450 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 1455 00 |
| Деталь: | DUCT |
| Парткод: | A0ED 1453 00 |
| Деталь: | FAN MOTOR |
| Парткод: | A0ED M105 00 |
| Деталь: | DUCT |
| Парткод: | A0ED 1457 00 |
| Деталь: | FILTER |
| Парткод: | A0ED 1409 00 |
| Деталь: | DUCT |
| Парткод: | A0ED 1456 00 |
| Деталь: | HOPPER DRIVE ASSY |
| Парткод: | A0ED R706 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2625 00 |
| Деталь: | SEAL |
| Парткод: | 4581 1625 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 2632 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2624 00 |
| Деталь: | COVER |
| Парткод: | A0ED 2623 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2662 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2627 00 |
| Деталь: | Scanner Wiring /2 |
| Парткод: | A0ED N142 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0903 01 |
| Деталь: | COVER |
| Парткод: | A0ED 2622 00 |
| Деталь: | FRAME |
| Парткод: | A0ED 2621 00 |
| Деталь: | FRAME |
| Парткод: | A0ED 2619 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2626 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2630 00 |
| Деталь: | FRAME |
| Парткод: | A0E D 2620 00 |
| Деталь: | Fuser Unit(100V) |
| Парткод: | A0ED R719 00 |
| Деталь: | Fuser Unit(120V) |
| Парткод: | A0ED R720 00 |
| Деталь: | Fuser Unit(230V) |
| Парткод: | A0ED R721 00 |
| Деталь: | Fuser Unit(110V) |
| Парткод: | A0ED R738 00 |
| Деталь: | Waste Toner Box |
| Парткод: | A162WY1 |
| Деталь: | ORIGINAL GLASS ASSY |
| Парткод: | A0ED R727 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2684 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2685 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 2673 00 |
| Деталь: | Holding Plate |
| Парткод: | A0ED 2683 00 |
| Деталь: | Holding Plate |
| Парткод: | A0ED 2682 00 |
| Деталь: | COVER |
| Парткод: | A0ED 2786 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2817 00 |
| Деталь: | PWB assembly(PWB-UCN ASSY) |
| Парткод: | A0P0 H025 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2818 00 |
| Деталь: | CABLE |
| Парткод: | A0P0 N153 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2819 00 |
| Деталь: | LOUDSPEAKER |
| Парткод: | 4040 M401 00 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326 1810 51 |
| Деталь: | REGULATING PLATE |
| Парткод: | A00J 2653 00 |
| Деталь: | Holding Plate |
| Парткод: | A0ED 2688 00 |
| Деталь: | CCD Lens |
| Парткод: | A0ED R725 00 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A0ED N140 00 |
| Деталь: | Slit Glass Assy |
| Парткод: | A0ED R726 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 1692 00 |
| Деталь: | COVER |
| Парткод: | A00J 1691 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 2681 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0ED 2687 00 |
| Деталь: | COVER |
| Парткод: | A0ED 2675 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 1348 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 4100 02 |
| Деталь: | HOLDER |
| Парткод: | A0ED 2210 00 |
| Деталь: | Gear 27/26T |
| Парткод: | A0ED 2209 00 |
| Деталь: | Gear 24/24T |
| Парткод: | A0ED 2205 00 |
| Деталь: | Gear 27/34T |
| Парткод: | A0ED 2208 00 |
| Деталь: | Gear 32/27T |
| Парткод: | A0ED 2206 00 |
| Деталь: | Gear 31T |
| Парткод: | A0ED 2207 00 |
| Деталь: | GEAR 25T |
| Парткод: | A0ED 2204 00 |
| Деталь: | Gear 31T |
| Парткод: | A0ED 2201 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A0ED 2211 00 |
| Деталь: | Color Developing motor Assy |
| Парткод: | A0ED R724 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 2115 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 2114 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | DC Brushless motor |
| Парткод: | A0ED M100 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 1347 00 |
| Деталь: | 2nd Paper Feed Drive Assy |
| Парткод: | A0ED R705 00 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A0ED R704 00 |
Коды ошибок
C0001
C0202
C0204
C0206
C0208
C0209
C0210
C0211
C0212
C0213
C0214
C0215
C1004
C1081
C1113
C1114
C1115
C1116
C1150
C1156
C1181
C1182
C1183
C1190
C1191
C1194
C11A1
C11A2
C11A7
C11B0
C11B2
C11B5
C11C0
C11E0
C11E1
C11E2
C1301
C1402
C2152
C2164
C2253
C2254
C225D
C2355
C2411
C2412
C2413
C2414
C2551
C2552
C2553
C2554
C2555
C2556
C2557
C2558
C2559
C255A
C255B
C255C
C2561
C2562
C2563
C2564
C2650
C2A11
C2A12
C2A13
C2A14
C3101
C3201
C3202
C3302
C3421
C3423
C3721
C3722
C3723
C3821
C3823
C3921
C3923
C4101
C4501
C5102
C5103
C5351
C5354
C5355
C5370
C5372
C5501
C5601
C6102
C6103
C6704
C6751
C6752
C6753
C6901
C6902
C6903
C6F01
C8101
C8102
C8103
C8106
C8107
C8302
C8401
C9401
C9402
CA051
CA052
CA053
CB001 ... CB119
CC001
CC151 ... CC165
CD004 ... CD04B
CE001 ... CEEE1
CEEE2
CEEE3
CFB00 ... CFF5E
Описание
| Error code: | C0001 |
| Description: | Main Motor turning at abnormal timing The Main Motor Lock signal remains faulty for a predetermined continuous period of time while the Main Motor remains stationary. |
| Remedy: | 1 Main Motor rotation while it is being energized: the voltage across PJ13I-7A on Master Board and GND remains DC 0 V. YES: Change Master Board. NO: Change motor. |
| Error code: | C0202 |
| Description: | Magenta PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 1 upper limit sensor (PS6) • Tray 1 lift-up motor (M6) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0204 |
| Description: | Yellow PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 2 upper limit sensor (PS14) • Tray 2 lift-up motor (M8) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0206 |
| Description: | Black PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 3 upper limit sensor (PS22) • Tray 3 lift-up motor (M23) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0208 |
| Description: | Tray 5 feeder up/down abnormality |
| Causes: | • Tray 4 upper limit sensor (PS27) • Tray 4 lift-up motor (M24) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Error code: | C0209 |
| Description: | LCT elevator motor malfunction |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0211 |
| Description: | Tray 1 feeder up/down abnormality • The paper feed tray 1 lift-up position sensor is not unblocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The paper feed tray 1 lift-up position sensor is not blocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started. |
| Causes: | • Bypass lift-up motor (M26) • Bypass upper limit sensor (PS35) • Bypass lower limit sensor (PS36) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check the connector of M1 for proper drive coupling and correct as necessary. 3 PS17 I/O check PRCB CN6PRCB-7 (ON) D-2. 4 SL1 operation check PRCB CN6PRCB-4 (ON) D-1. 5 M1 operation check PRCB CN34PRCB-10 (REM) PRCB CN34PRCB-13 (LOCK) D-22. 6 Change SL1. 7 Change M1. 8 Change PRCB. |
| Error code: | C0212 |
| Description: | LCT ejection failure |
| Error code: | C0213 |
| Description: | LCT shift gate malfunction |
| Error code: | C0214 |
| Description: | LCT shifting failure |
| Causes: | • Shifter motor (M133) • Shifter stop / lower limit position sensor (PS138) • Shifter home sensor (PS139) • PC control board (PCCB) |
| Error code: | C0215 |
| Description: | LCT shift motor malfunction |
| Error code: | C1004 |
| Description: | FNS communication error |
| Causes: | FS control board (FSCB) |
| Error code: | C1081 |
| Description: | SD communication error <When FS-534+SD-511 is installed> When a communication error is detected between the FS control board (FSCB) and the SD control board (SDDB). |
| Causes: | • SD drive board (SDDB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace SDDB. 4 Replace FSCB. |
| Error code: | C1113 |
| Description: | Stopper drive motor`s malfunction. <When FS-536SD or FS-537SD is installed> The stopper home sensor (PS6) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stopper drive motor (M4) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Stopper drive motor (M4) • Stopper home sensor (PS6) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M4-SDCB J10 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-SDCB J10 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: SDCB J10-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 2-P 5. M4 operation check • Control signal: SDCB J10-6 to 9 • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 1-P 6. Replace M4. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1114 |
| Description: | Alignment motor’s malfunction. <When FS-536SD or FS-537SD is installed> The alignment home sensor (PS4) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the alignment motor (M3) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Alignment motor (M3) • Alignment home sensor (PS4) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M3-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS4-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS4 I/O check, sensor check • Control signal: SDCB J7-6 (ON) • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 5. M3 operation check • Control signal: SDCB J7-7 to 10 • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 6. Replace M3. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1115 |
| Description: | Center fold knife motor`s malfunction. <When FS-536SD or FS-537SD is installed> The center fold knife home sensor (PS8) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Center fold knife motor (M9) • Center fold knife home sensor (PS8) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M9-SDCB J11 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS8-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS8 I/O check, sensor check • Control signal: SDCB J7-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-P, FS-537/FS-537SD 6-P 5. M9 operation check • Control signal: SDCB J11-11 to 20 • Location of electrical component: FS-536/FS-536SD 2-L, FS-537/FS-537SD 1-K 6. Replace M9. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1116 |
| Description: | Center-staple transfer motor malfunction <When FS-526+SD-508 is installed> • The transport motor (M33) does not reach the specified speed even after the set period of time has elapsed after it starts to operate. <When FS-527+SD-509 is installed> • The center fold roller motor (M25) does not reach the specified speed even after the set period of time has elapsed after it starts to operate. |
| Causes: | When FS-526+SD-508 is installed: Transport motor (M33) SD drive board (SDDB) FS control board (FSCB). When FS-527+SD-509 is installed: Center fold roller motor (M25) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | When FS-526+SD-508 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M33 for proper drive coupling, and correct as necessary. - - 3 M33 operation check SDDB CN409-1 to 11 SD-508 K-5 4 Change M33 - - 5 SDDB ICP5 conduction check - - 6 Change SDDB - - 7 Change FSCB. When FS-527+SD-509 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M25 for proper drive coupling, and correct as necessary. - - 3 M25 operation check SDDB PJ4-1 to 11 SD-509 B-3 4 Change M25 - - 5 Change SDDB - - 6 Change FSCB |
| Error code: | C1150 |
| Description: | Side feeder lift motor going down error (optional side feeder) • Lower limit detection switch does not turn off within 15 s of the side feeder lift motor starting (within 200 ms during paper feeding). This error is detected four times successively. |
| Causes: | Poor contact of lower limit detection switch connector terminals. Defective side feeder main PWB. Defective side feeder lift motor. |
| Remedy: | Poor contact of lower limit detection switch connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective side feeder main PWB. Replace the side feeder main PWB. Defective side feeder lift motor. Run maintenance mode U247 and measure the voltage between terminals YC5-A12 (side-feeder main circuit board) and YC6- B11. (Make sure all of LUSSW, UCSSW, LLSSW and RCSSW are off.) Despite either DC24V or DC-24V is observed but if the side-feeder lift motor does not operate, replace the side-feeder lift motor. |
| Error code: | C1156 |
| Description: | SD paddle motor malfunction. <When FS-536SD or FS-537SD is installed> The paddle home sensor (PS5) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the SD paddle motor (M7) is turning. |
| Causes: | <When FS-536SD or FS-537SD is installed> • SD paddle motor (M7) • Paddle home sensor (PS5) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M7-SDCB J8 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS5-SDCB J8 for proper connection and correct as necessary. 4. PS5 I/O check, sensor check • Control signal: SDCB J8-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 5. M7 operation check • Control signal: SDCB J8-4 to 7 • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 6. Replace M7. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1181 |
| Description: | Paddle motor malfunctions |
| Error code: | C1182 |
| Description: | Unsupported option trouble |
| Causes: | When JS-504 is installed: Shift motor (M2) Shift home sensor (PS6) JS control board (JSCB). When FS-527 is installed: Tray2 shift motor (M16) Tray2 shift home sensor (PS25) FS control board (FSCB) |
| Error code: | C1183 |
| Description: | Finishing option elevator drive malfunction |
| Causes: | Elevate motor (M15) Tray1 lower position sensor (PS21) Tray1 upper position sensor (PS24) Tray1 upper position switch (SW2) Tray1 lower position switch (SW3) FS control board (FSCB) |
| Error code: | C1190 |
| Description: | Finishing option aligning bar moving mechanism malfunction 1 |
| Causes: | Alignment plate motor (M13) Alignment plate home sensor (PS17) FS control board (FSCB) |
| Error code: | C1191 |
| Description: | Finishing option aligning bar moving mechanism malfunction 2 |
| Error code: | C1194 |
| Description: | Leading edge stopper motor drive malfunction <When FS-527 is installed> • The leading edge stopper home sensor (PS20) is turned neither ON nor OFF even after the set period of time has elapsed after the leading edge stopper motor (M14) is turned ON. |
| Causes: | Leading edge stopper motor (M14) Leading edge stopper home sensor (PS20) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M13 for proper drive coupling, and correct as necessary. - - 3 PS17 I/O check, sensor check FSCB PJ17-6 (ON) FS-527 B to C-8 4 M13 operation check FSCB PJ8-9 to 12 FS-527 B to C-6 5 Change M13 - - 6 Change FSCB |
| Error code: | C11A1 |
| Description: | Finishing option exit roller pressure/retraction failure |
| Causes: | Exit roller retraction motor (M9) Exit roller pressure sensor (PS12) FS control board (FSCB) |
| Error code: | C11A2 |
| Description: | Saddle exit roller pressure/retraction failure |
| Causes: | <When FS-536 or FS-536SD is installed> • Receiving roller retraction motor (M4) • Receiving roller retraction sensor (PS11) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Receiving roller retraction motor (M10) • Receiving roller retraction sensor (PS22) • FS control board (FSCB) |
| Error code: | C11A7 |
| Description: | Tray 3 exit roller pressure/ retraction malfunction <When JS-603 is installed> • The exit roller pressure sensor (PS12) is turned neither ON nor OFF even after the set period of time has elapsed after the exit roller retraction motor (M9) is turned ON. |
| Causes: | Tray3 exit roller retraction motor (M17) Tray3 exit roller retraction sensor (PS35) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M17 for proper drive coupling, and correct as necessary. - - 3 PS35 I/O check, sensor check FSCB PJ12-6 (ON) FS-527 (JS-603) L-10 4 M17 operation check FSCB PJ30-2 (REM) FS-527 (JS-603) L-9 5 Change M17 - - 6 Change FSCB |
| Error code: | C11B0 |
| Description: | Finishing option stapler unit CD drive failure |
| Causes: | Stapler movement motor (M11) Stapler home sensor/1 (PS18) Stapler home sensor/2 (PS19) FS control board (FSCB) |
| Error code: | C11B2 |
| Description: | Finishing option stapling mechanism malfunction 1 |
| Causes: | Stapler unit FS control board (FSCB) |
| Error code: | C11B5 |
| Description: | Side staple 1 drive failure |
| Causes: | Saddle stapler unit SD drive board (SDDB) FS control board (FSCB) |
| Error code: | C11C0 |
| Description: | Punch motor malfunction |
| Causes: | Punch motor/1 (M100) Punch home sensor/1 (PS100) FS control board (FSCB) |
| Error code: | C11E0 |
| Description: | Unsupported option trouble |
| Causes: | When FS-527 is installed: Duplex path switching motor (M2) Duplex path switching sensor (PS3)FS control board (FSCB). When JS-504 is installed: Route change motor (M3) Route change home sensor (PS4) JS control board (JSCB) |
| Error code: | C11E1 |
| Description: | Paper exit switching drive malfunction. <When FS-536 or FS-536SD is installed> The exchange folded paper output sensor (PS30) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the FNS entry transport motor (M2) is turned ON. <When FS-537 or FS-537SD is installed> The route change gate home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the route change gate motor (M4) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS entry transport motor (M2) • Exchange folded paper output sensor (PS30) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Route change gate motor (M4) • Route change gate home sensor (PS21) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M2-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS30-FSCB J4 for proper connection and correct as necessary. 4. PS30 I/O check, sensor check • Control signal: FSCB J4<A>-15 (ON) • Location of electrical component: FS-536/FS-536SD 14-C 5. M2 operation check • Control signal: FSCB J9<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 12-C 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M4-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-FSCB J12 for proper connection and correct as necessary. 4. PS21 I/O check, sensor check • Control signal: FSCB J12<B>-12 (ON) • Location of electrical component: FS-537/FS-537SD 18-D 5. M4 operation check • Control signal: FSCB J21<B>-8 to 9 • Location of electrical component: FS-537/FS-537SD 18-D 6. Replace M4. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C11E2 |
| Description: | Paper exit switching (JS) drive malfunction. <When FS-537 or FS-537SD is installed> The sub tray/JS route change gate home sensor (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the sub tray discharge motor (M18) is turned ON. |
| Causes: | • Sub tray discharge motor (M18) • Sub tray/JS route change gate home sensor (PS23) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M18-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M18 for proper drive coupling and correct as necessary. 3. Check the connector between PS23-FSCB J12 for proper connection and correct as necessary. 4. PS23 I/O check, sensor check • Control signal: FSCB J12<A>-16 (ON) • Location of electrical component: FS-537/FS-537SD 17-D 5. M18 operation check • Control signal: FSCB J12<A>-5 to 6 • Location of electrical component: FS-537/FS-537SD 16-D 6. Replace M18. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1301 |
| Description: | Finishing option cooling fan motor failure |
| Error code: | C1402 |
| Description: | IR illegal interrupt vector occurred |
| Causes: | FS control board (FSCB) |
| Remedy: | 1. Reset the malfunction. 2. If the same malfunction persists, change the Image Processing Board. |
| Error code: | C2152 |
| Description: | Transfer belt pressure welding alienation • During a retraction operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its retracted position within a predetermined period of time after the transfer belt retraction clutch is turned ON. • During a pressure operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its pressed position within a predetermined period of time after the transfer belt clutch is turned ON. |
| Causes: | • 1st transfer pressure sensor/K (PS51) • 1st transfer pressure sensor/YMC (PS52) • 1st transfer pressure motor (M21) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 PS31 I/O check PRCB CN36PRCB-15 (ON) D-26 to 27. 3 CL7 operation check PRCB CN39PRCB-10 (ON) D-23. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change CL7. 6 Change M5. 7 Change PRCB. |
| Error code: | C2164 |
| Description: | PC charge malfunction • When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined period of time. |
| Causes: | • Imaging unit • High voltage unit/1 (HV1) • Printer control board (PRCB) |
| Remedy: | 1 Check the imaging unit for proper connection and correct as necessary. 2 Check the HV connector for proper connection and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Change IU. 5 Change HV. 6 Change PRCB. |
| Error code: | C2253 |
| Description: | Color PC motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/YMC (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2254 |
| Description: | Color PC motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/YMC motor (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C225D |
| Description: | Color dev. unit engagement/disengagement failure • The gears remain disengaged after the lapse of a predetermined period of time after the engagement operation is started by the color dev. unit engaged motor. • The gears remain engaged after the lapse of a predetermined period of time after the disengagement operation is started by the color dev. unit engaged motor. |
| Remedy: | 1 Check the M10 connector for proper connection and correct as necessary. 2 Check the M10 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 PS26 I/O check PRCB CN39PRCB-18 (ON) D-24. 5 M10 operation check PRCB CN39PRCB-12 (REM) D-24. 6 Change M10. 7 Change PRCB. |
| Error code: | C2355 |
| Description: | Transfer belt cleaner cooling fan motor’s failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Transfer belt cleaner cooling fan (FM2) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between FM2-relay CN115- PRCB CN13 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM2 operation check PRCB CN13-8 (REM) PRCB CN13-10 (LOCK) 24-C. 4 Replace FM2. 5 PRCB ICP3 conduction check. 6 Replace PRCB. |
| Error code: | C2411 |
| Description: | Developing unit/C new article release The status with the new unit is not cleared after the new developing unit is set. |
| Remedy: | 1 Reinstall developing unit. 2 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16 for proper connection and correct as necessary. 3 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 4 Replace the developing unit. 5 Replace FRB. 6 Replace PRCB. |
| Error code: | C2412 |
| Description: | Developing unit/M new article release The status with the new unit is not cleared after the new developing unit is set. |
| Remedy: | 1 Reinstall developing unit. 2 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16 for proper connection and correct as necessary. 3 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 4 Replace the developing unit. 5 Replace FRB. 6 Replace PRCB. |
| Error code: | C2413 |
| Description: | Developing unit/Y new article release The status with the new unit is not cleared after the new developing unit is set. |
| Remedy: | 1 Reinstall developing unit. 2 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16 for proper connection and correct as necessary. 3 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 4 Replace the developing unit. 5 Replace FRB. 6 Replace PRCB. |
| Error code: | C2414 |
| Description: | Developing unit new article release. The status with the new unit is not cleared after the new developing unit is set. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Replace the developing unit. 3. Replace MFPB. |
| Error code: | C2551 |
| Description: | Abnormally low toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2552 |
| Description: | Abnormally high toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2553 |
| Description: | Abnormally low toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2554 |
| Description: | Abnormally high toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2555 |
| Description: | Abnormally low toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2556 |
| Description: | Abnormally high toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2557 |
| Description: | Abnormally low toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Developing unit • Toner cartridge • Toner empty sensor/K (PZS/K) • Toner supply motor/K (M12) • Toner cartridge motor/CK (M14) • MFP board (MFPB) |
| Remedy: | 1 M3 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 D-23. 2 Reinstall imaging unit. 3 Reinstall toner cartridge. 4 Change imaging unit /K. 5 Change PRCB. |
| Error code: | C2558 |
| Description: | Abnormally high toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Developing unit • Toner cartridge • Sub hopper unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit /K. 4 Change PRCB. |
| Error code: | C2559 |
| Description: | Cyan TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255A |
| Description: | Magenta TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255B |
| Description: | Yellow TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255C |
| Description: | Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit /K. 2 Change imaging unit /K. 3 Change PRCB. |
| Error code: | C2561 |
| Description: | Cyan TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Developing unit /K • PH relay board (PHRYB) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall developing unit. 2 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16 for proper connection and correct as necessary. 3 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 4 Replace the developing unit. 5 Replace FRB. 6 Replace PRCB. |
| Error code: | C2562 |
| Description: | Magenta TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Developing unit /K • PH relay board (PHRYB) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall developing unit. 2 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16 for proper connection and correct as necessary. 3 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 4 Replace the developing unit. 5 Replace FRB. 6 Replace PRCB. |
| Error code: | C2563 |
| Description: | Yellow TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Developing unit /K • PH relay board (PHRYB) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall developing unit. 2 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16 for proper connection and correct as necessary. 3 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 4 Replace the developing unit. 5 Replace FRB. 6 Replace PRCB. |
| Error code: | C2564 |
| Description: | Black TCR sensor failure. • The TCR sensor input is 0. • This detection is used for detecting disconnection of TCR sensor connector. |
| Causes: | • Developing unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Check the connector between the developing unit-relay CN214-PHRYB CN6 for proper connection and correct as necessary. 3. Replace the developing unit. 4. PHRYB PS1 conduction check. 5. Replace PHRYB. 6. Replace MFPB |
| Error code: | C2650 |
| Description: | PF feed motor error (Side Multi Feeder) Object: Side multi feeder |
| Causes: | The ready signal is not at the L level (stable rotation) for passing 2s since the PF feed motor drive is started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected. The drive parts are faulty. Execute U247 [SMT] > [Motor On] to check the paper feeding operation. If the PF feed motor does not properly operate, reconnect the connector. Check if the PF feed roller and the drive gears rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. Executing U247 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF main PWB • PF main PWB - Engine PWB (Cable from the side multi feeder) Wiring diagram 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF drive unit (Side multi feeder) 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 5 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2A11 |
| Description: | Drum unit/C new release failure The status with the new unit is not cleared after the new drum unit is set. |
| Causes: | • Imaging unit/Y,M,C • Drum unit/K • MFP board (MFPB) |
| Remedy: | 1 Clean the connection between the drum unit and the machine if dirty. 2 Reinstall drum unit. 3 Check the connector between drum unit-FRB CN12 for proper connection and correct as necessary. 4 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 5 Replace the drum unit. 6 Replace FRB. 7 Replace PRCB. |
| Error code: | C2A12 |
| Description: | Drum unit/M new release failure The status with the new unit is not cleared after the new drum unit is set. |
| Causes: | • Imaging unit/Y,M,C • Drum unit/K • MFP board (MFPB) |
| Remedy: | 1 Clean the connection between the drum unit and the machine if dirty. 2 Reinstall drum unit. 3 Check the connector between drum unit-FRB CN12 for proper connection and correct as necessary. 4 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 5 Replace the drum unit. 6 Replace FRB. 7 Replace PRCB. |
| Error code: | C2A13 |
| Description: | Drum unit/Y new release failure The status with the new unit is not cleared after the new drum unit is set. |
| Causes: | • Imaging unit/Y,M,C • Drum unit/K • MFP board (MFPB) |
| Remedy: | 1 Clean the connection between the drum unit and the machine if dirty. 2 Reinstall drum unit. 3 Check the connector between drum unit-FRB CN12 for proper connection and correct as necessary. 4 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 5 Replace the drum unit. 6 Replace FRB. 7 Replace PRCB. |
| Error code: | C2A14 |
| Description: | Drum unit new release failure. The status with the new unit is not cleared after the new drum unit is set. |
| Causes: | • Drum unit • MFP board (MFPB) |
| Remedy: | 1. Clean the connection between the drum unit and the developing unit if dirty. 2. Reinstall the drum unit. 3. Check the harness for proper connection and correct as necessary. 4. Replace the drum unit. 5. Replace MFPB. |
| Error code: | C3101 |
| Description: | Fusing roller separation failure • With the fusing roller being retracted, the pulse of the fusing roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • With the fusing roller being pressed, the pulse of the roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • During a pressure operation of the fusing roller, the fusing roller is not at the pressed position even after the roller retraction sensor counts the specified number of pulses after the fusing retraction motor starts rotating. |
| Causes: | • Fusing pressure home sensor (PS55) • Fusing pressure motor (M29) • Printer control board (PRCB) • Fusing unit |
| Remedy: | 1 Check the M12 connector for proper connection and correct as necessary. 2 PS38 I/O check PRCB CN28PRCB-8 (ON) D-25. 3 M12 operation check PRCB CN28PRCB-4 to 5 D-25. 4 Change M12. 5 Change fusing unit. 6 Change PRCB. |
| Error code: | C3201 |
| Description: | Fusing motor failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3202 |
| Description: | Fusing motor turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3302 |
| Description: | Fusing cooling fan motor/ 2,3 failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Paper cooling fan (FM8) • Printer control board (PRCB) |
| Remedy: | 1 Check the FM10 or FM11 connector for proper connection and correct as necessary 2 Check the fan for possible overload and correct as necessary. 3 FM10/FM11 operation check PRCB CN40PRCB-5 (ON) PRCB CN40PRCB-6 (LOCK) D-19. PRCB CN40PRCB-8 (ON) PRCB CN40PRCB-9 (LOCK) D-18. 4 Change FM10/FM11. 5 Change PRCB. |
| Error code: | C3421 |
| Description: | Fusing heaters trouble (heating side) • The temperature detected by the heating roller thermistor/C does not reach a predetermined level after the lapse of a predetermined period of time after the heating roller fusing heater lamp lights up. • The difference between the maximum and minimum temperatures detected by the heating roller thermistor/C within a predetermined period of time after the start of a warm-up cycle is below or above a predetermined value. • The temperature detected after a pressure level correction remains under a predetermined level even after the lapse of a predetermined period of time after the start of the temperature detection. • During a warm-up, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. |
| Causes: | • Fusing unit • C3421: Fusing temperature sensor/1 (TEM1: center) • C3426: Fusing temperature sensor/1 (TEM1: edge) • DC power supply (DCPS) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3423 |
| Description: | Fusing heaters trouble (pressurizing side) • After warm-up operation starts, the fusing pressure roller thermistor does not detect a temperature as high as a predetermined one though a predetermined period of time has elapsed. • The temperature of the pressure roller remains lower than a predetermined level even after the lapse of a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3721 |
| Description: | Fusing abnormally high temperature detection (heating side) • The heating roller thermistor continues to detect a temperature higher than a predetermined one for a predetermined period of time. • Hard protection signal L is detected continuously over a predetermined period of time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3722 |
| Description: | Fusing abnormally high temperature detection (Edge of the heating side) Detected temperature of the heating roller thermistor/1 (TH1) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3723 |
| Description: | Fusing abnormally high temperature detection (pressurizing side) • The temperature of the pressure roller continues to be higher than a predetermined level for a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • Pressure roller power supply unit (PRPU) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3821 |
| Description: | Fusing abnormally low temperature detection (heating side) • The heating roller thermistor continues to detect a temperature lower than a predetermined one for a predetermined period of time. • In the states other than a warm-up operation, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. • The power supply frequency cannot be detected. |
| Causes: | • Fusing unit • C3821: Thermistor/1 (TH1) • C3822: Thermistor/2 (TH2) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3823 |
| Description: | Fusing abnormally low temperature detection (pressurizing side) • The temperature of the pressure roller continues to be lower than a predetermined level for a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • Pressure roller power supply unit (PRPU) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3921 |
| Description: | Fusing sensor wire breaks detection (Center of the heating roller) • At the warm-up stage, the heating roller temperature sensor/2 voltage does not decrease by predetermined steps (temperature rise) within a predetermined time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, PRCB and REDB for proper connection and correct or change as necessary. - - 4 Change TEMS1, TEMS2 or TEMS3 - - 5 Change fusing unit - - 6 Change IHPU - - 7 PRCB ICP17 conduction check - - 8 Change PRCB - - 9 Change REDB |
| Error code: | C3923 |
| Description: | Fusing sensor wire breaks detection (pressure). The maximum value and minimum value of detected temperature of the pressure roller thermistor/2 (TH3) is compared after a lapse of given time from starting of warm up and the gap between the value of maximum and minimum is below a given temperature. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between NF1 CN2-IHPU CN1 for proper connection and correct as necessary. 5. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 6. Replace the fusing unit. 7. Replace IHPU. 8. Replace MFPB. 9. Replace NF1. |
| Error code: | C4101 |
| Description: | BD initialization error |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4501 |
| Description: | Laser malfunction. • SOS signal is not detected even after the lapse of a given period of time after starting the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Causes: | • PH unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between the PH unit-PHRYB CN8 for proper connection and correct as necessary. 2. Replace the PH unit. 3. PHRYB IC5 conduction check. 4. Replace PHRYB. 5. Replace MFPB. |
| Error code: | C5102 |
| Description: | Main high-voltage error C |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5103 |
| Description: | Main high-voltage error M |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5351 |
| Description: | Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • DC power supply cooling fan (FM9) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1 Check the FM5 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check PRCB CN30PRCB-11 (ON) PRCB CN30PRCB-12 (LOCK) K-8. 4 Change FM5. 5 Change DCPU. 6 Change PRCB. |
| Error code: | C5354 |
| Description: | Exhaust fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Ozone ventilation fan (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM4 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM4 operation check PRCB CN3PRCB-14 (ON) PRCB CN3PRCB-16 (LOCK) D-6. 4 Change FM4. 5 Change PRCB. |
| Error code: | C5355 |
| Description: | Toner cartridge cooling fan’s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Toner cartridge cooling fan (FM8) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM8-relay CN522-MFPB CN24E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM8 operation check • Control signal: MFPB CN24E-4 (DRIVE), MFPB CN24E-6 (LOCK) • Location of electrical component: 1-K 4. Replace FM8. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE: • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C5370 |
| Description: | Rear side cooling fan’s failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan remains stationary. |
| Causes: | • MFP control board cooling fan (FM17) • MFP board (MFPB) |
| Remedy: | 1 Check the connector between FM3-MFPB PJ26 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM3 operation check MFPB PJ26 (LOCK) 7-P. 4 Replace FM3. 5 Replace MFPB. |
| Error code: | C5372 |
| Description: | MFP control board CPU temperature failure. Temperature failure of CPU on the MFP board was detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Reboot the machine. 2. Check for clogging in the ventilation path between the MFPB and the power supply cooling fan, and correct as necessary. 3. Replace MFPB. |
| Error code: | C5501 |
| Description: | AC signal abnormality The zero cross signal is not input during fusing phase control. |
| Causes: | • Fusing unit • DC power supply (DCPU) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU and PRCB for proper connection and correct or change as necessary. 3 Replace fusing unit. 4 Replace PRCB. 5 Replace DCPU. |
| Error code: | C5601 |
| Description: | Engine control malfunction. Engine control malfunction is detected with port monitor control. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | C6102 |
| Description: | Drive system home sensor malfunction • The scanner home sensor (PS201) is unable to detect the scanner located at its home position. • The scanner home sensor (PS201) is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor (PS201) detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor (PS201). |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6103 |
| Description: | Slider over running The scanner home sensor (PS201) detects the scanner at its home position during a period of time that begins with the time when a prescan command and a scan preparation command are executed and ends when a home return command is executed. |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6704 |
| Description: | Image input time out. Image data is not input from the scanner to the MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Memory Bus Check] -> [Scanner -> Memory], and conduct the memory bus function. 2. Correct the harness connection between scanner section and MFPB if faulty. 3. MFPB F3E conduction check 4. Replace MFPB. 5. Replace the CCD unit. |
| Error code: | C6751 |
| Description: | CCD gain adjustment failure. • The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment. |
| Causes: | • LED exposure unit • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 2. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 3. Correct the harness connection between SCDB CN1-DCPU CN005 if faulty. 4. Check for possible extraneous light and correct as necessary. 5. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 6. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 7. Replace SCDB 8. Replace the CCD unit. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | C6752 |
| Description: | ASIC clock input error (front side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on CCD board (CCDB) was conducted, and verification failure was detected. |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Correct the harness connection of CCDB if faulty. 2. Replace the CCD unit. 3. MFPB F3E conduction check 4. Replace MFPB. |
| Error code: | C6753 |
| Description: | ASIC clock input error (back side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on dual scan image processing board (DSIPB) was conducted, and verification failure was detected. |
| Causes: | • CIS module (CIS) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CIS J101-DSIPB CN2 if faulty. 2. Correct the harness connection between DSIPB CN1-MFPB CN24 if faulty. 3. Replace CIS. 4. DFPU ICP1 conduction check. 5. Replace DSIPB. 6. MFPB F3E conduction check 7. Replace MFPB. |
| Error code: | C6901 |
| Description: | DSC board mount failure 1 When MFP detects that DSC board/1 (front side) is not properly installed. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6902 |
| Description: | DSC board bus check NG1-1 When DSC bus check (front side) detects an error. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6903 |
| Description: | DSC board bus check NG1-2 When DSC bus check (front side) detects an error. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6F01 |
| Description: | Scanner sequence trouble 1. The original transport interval becomes shorter than the predetermined value due to an original transport control error in original reading in DF. |
| Causes: | • MFP board (MFPB) • DF control board (DFCB) |
| Remedy: | 1. Correct the harness connection between main body and DF if faulty. 2. Replace DFCB. 3. Replace MFPB. |
| Error code: | C8101 |
| Description: | Before reading pressure welding alienation mechanism trouble. • During a pressure motion being performed, the before read sensor (PS6) output does not change from H to L. • During a retraction motion being performed, the before read sensor (PS6) output does not change from L to H. |
| Causes: | • Reading roller pressure/retraction motor (M6) • Before read sensor (PS6) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M6-relay CN118-DFCB CN4 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-relay CN120-DFCB CN11 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: DFCB CN11-2 (ON) • Location of electrical component: DF 1-C 5. M6 operation check • Control signal: DFCB CN4-1 to 2 • Location of electrical component: DF 10-C 6. Replace M6. 7. DFCB ICP9 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8102 |
| Description: | Turn around pressure welding alienation trouble •During a pressure motion being performed, the reverse roller sensor (PS7) output does not change from H to L. •During a retraction motion being performed, the reverse roller sensor (PS7) output does not change from L to H. |
| Causes: | Switchback roller pressure/retraction motor (M5) Reverse roller sensor (PS7) DF control board (DFCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M5 for proper drive coupling, and correct as necessary. - - 3 PS7 I/O check, sensor check REYB PJ3-3 (ON) DF-618 K to L-10 4 DFCB F9 conduction check - - 5 M5 operation check DFCB PJ6-10 to 11 DF-618 I-7 6 Change M5 - - 7 DFCB PS2 conduction check - - 8 Change DFCB |
| Error code: | C8103 |
| Description: | Lift up mechanism trouble (Upward movement). The lift up upper sensor (PS2) is not turned ON (unblocked) after a lapse of a given time after the lift-up motor (M5) moves up (is turned forward). |
| Causes: | • Lift-up motor (M5) • Lift up upper sensor (PS2) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M5-DFCB CN9 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-DFCB CN6 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: DFCB CN6-3 (ON) • Location of electrical component: DF 7-I 5. M5 operation check • Control signal: DFCB CN9-1 to 5 • Location of electrical component: DF 5-C 6. Replace M5. 7. DFCB ICP5 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8106 |
| Description: | Lift up mechanism failure (Downward movement). The lift up lower sensor (PS3) is not turned ON (unblocked) after a lapse of a given time after the lift-up motor (M5) goes down (is turned backward). |
| Causes: | • Lift-up motor (M5) • Lift up lower sensor (PS3) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M5-DFCB CN9 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS3-DFCB CN10 for proper connection and correct as necessary. 4. PS3 I/O check, sensor check • Control signal: DFCB CN10-3 (ON) • Location of electrical component: DF 10-C 5. M5 operation check • Control signal: DFCB CN9-1 to 5 • Location of electrical component: DF 5-C 6. Replace M5. 7. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8107 |
| Description: | Glass cleaning mechanism trouble. The front side cleaning home sensor (PS18) is not turned ON (unblocked) even after the set period of time has elapsed after the front side cleaning motor (M8) turned ON. |
| Causes: | • Front side cleaning motor (M8) • Front side cleaning home sensor (PS18) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M8-DFCB CN14 for proper connection and correct as necessary. 2. Check the connector between PS18-DFCB CN18 for proper connection and correct as necessary. 3. Check the connector of M8 for proper drive coupling and correct as necessary. 4. PS18 I/O check, sensor check • Control signal: DFCB CN18-3 (ON) • Location of electrical component: DF 3-C 5. M8 operation check • Control signal: DFCB CN14-1 to 4 • Location of electrical component: DF 6-C 6. Replace M8. 7. DFCB ICP8 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8302 |
| Description: | Cooling fan motor`s failure. The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Cooling fan motor (FM) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between FM-relay CN115-DFCB CN19 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM operation check • Control signal: DFCB CN19-3 (LOCK) • Location of electrical component: DF 4-C 4. Replace FM. 5. DFCB ICP10 conduction check. 6. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8401 |
| Description: | Nonvolatile memory error. The EEPROM writing is disabled. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Check the DFCB connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Replace DFCB. |
| Error code: | C9401 |
| Description: | Exposure LED lighting failure The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | C9402 |
| Description: | Exposure LED lighting abnormally The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | CA051 |
| Description: | Standard controller configuration failure • The controller of the printer control board (PRCB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA052 |
| Description: | Controller hardware error • A controller hardware error is detected in the network I/F. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA053 |
| Description: | Controller start failure • A controller start failure is detected in the controller interface. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CB001 ... CB119 |
| Description: | FAX board error |
| Error code: | CC001 |
| Description: | Vendor connection failure |
| Causes: | • Printer control board (PRCB) • Coin vendor (Japan) • Coin vendor kit (North America, Europe) |
| Error code: | CC151 ... CC165 |
| Description: | ROM contents error |
| Error code: | CD004 ... CD04B |
| Description: | Hard disk error |
| Error code: | CE001 ... CEEE1 |
| Description: | MFP board (MFPB) is fault |
| Error code: | CEEE2 |
| Description: | Scanner section malfunction. A scanner part is faulty. |
| Causes: | • LED exposure unit • CCD board (CCDB) • Scanner drive board (SCDB) |
| Remedy: | 1. Check the connectors on CCDB or MFPB for proper connection and correct as necessary. 2. Replace SCDB 3. Replace the CCD unit. |
| Error code: | CEEE3 |
| Description: | Printer control board (PRCB) |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Check the PRCB connector for proper connection and correct as necessary. - - 2 Replace PRCB |
| Error code: | CFB00 ... CFF5E |
| Description: | ASIC error • MFP board (MFPB) |
