Konica-Minolta bizhub C3110
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A4
Число страниц в месяц
120000
Скорость печати
A4
31
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Сканер |
|
Копир |
|
Тип устройства |
МФУ |
Область применения |
большой офис |
Цветность печати |
цветная |
Макс. формат |
A4 |
Размещение |
настольный |
Печать фотографий |
|
Факс |
|
Телефон |
|
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Число страниц в месяц |
120 000 |
Принтер |
|
Двусторонняя печать |
|
Прямая печать |
|
Количество цветов |
4 |
Макс, ширина отпечатка |
216 |
Макс, длина отпечатка |
356 |
Система непрерывной подачи чернил |
|
Печать без полей |
|
Пигментные чернила |
|
Время разогрева |
36 |
Макс, разрешение для ч/б печати |
|
| По X | 1 200 |
| По Y | 1 200 |
Скорость ч/б печати |
|
| A4 | 31 |
Время выхода первого отпечатка |
|
| Ч/б | 13 |
| Цветн, | 15 |
| Ч/б | 30 |
Копир |
|
Время выхода первой копии |
13 |
Шаг масштабирования |
0,1 |
Макс, количество копий за цикл |
99 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По X | 600 |
| По Y | 600 |
Скорость ч/б копирования |
|
| A3 | 31 |
Сканер |
|
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Устройство автоподачи оригиналов |
двустороннее |
Емкость устройства автоподачи оригиналов |
50 |
Тип сканера |
планшетный/протяжный |
Оттенки серого |
256 |
Стандарт WIA |
|
Макс. формат оригинала |
A4 |
Слайд-адаптер |
|
Макс, размер сканирования |
|
| По X | 216 |
| По Y | 297 |
Разрешение сканера |
|
| По Х (улучшенное) | 600 |
| По Х | 600 |
| По Y (улучшенное) | 600 |
Скорость сканирования |
|
| Цветн, | 30 |
Расходные материалы |
|
Количество картриджей |
4 |
Ресурс фотобарабана |
25 000 |
Ресурс цветного картриджа/тонера |
5 000 |
Ресурс ч/б картриджа/тонера |
5 000 |
Печать на: |
|
| Карточках |
|
| Пленках |
|
| Этикетках |
|
| Глянцевой бумаге |
|
| Конвертах |
|
| Матовой бумаге |
|
| Фотобумаге |
|
| Рулоне |
|
| CD/DVD |
|
Плотность бумаги |
|
| Максимальная | 210 |
| Минимальная | 60 |
Факс |
|
Цветной |
|
PC Fax |
|
Телефон |
|
Спикерфон |
|
Caller ID |
|
АОН |
|
Беспроводная трубка |
|
Проводная трубка |
|
Автоответчик |
|
Стандарт DECT |
|
Шрифты и языки управления |
|
Языки управления |
|
| PostScript 3 |
|
|
|
|
| PCL 5e |
|
| PostScript |
|
| PCL 5c |
|
| PCL 6 |
|
| PostScript 2 |
|
| PPDS |
|
Количество установленных шрифтов |
|
| PostScript | 137 |
| PCL | 80 |
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Максимальная | 850 |
| Стандартная | 350 |
Вывод бумаги |
|
| Стандартный | 150 |
Финишер |
|
Степлер |
|
Брошюровщик |
|
Электронная сортировка |
|
Сортировка со сдвигом |
|
Сортер |
|
Интерфейсы |
|
Ethernet (RJ-45) |
|
USB |
|
Веб-интерфейс |
|
Wi-Fi |
|
FireWire (IEEE 1394) |
|
RS-232 |
|
LPT |
|
AirPrint |
|
Инфракрасный порт |
|
Устройство для чтения карт памяти |
|
Bluetooth |
|
Wi-Fi 802.11n |
|
Версия USB |
2,0 |
Память/Процессор |
|
Объем памяти |
1 024 |
Макс, объем памяти |
2 048 |
Дополнительная информация |
|
Экран |
|
Работа от аккумулятора |
|
Поддержка ОС |
|
| Mac OS |
|
| Windows |
|
| Linux |
|
| DOS |
|
Потребляемая мощность |
|
| При работе | 500 |
Габариты |
|
Ширина |
447 |
Глубина |
544 |
Вес |
30 |
Высота |
500 |
Модули
MAIN DRIVE SECTION 2
PRINT HEAD SECTION
IR UNIT
ADF UNIT 2
VERTICAL CONVEYANCE SECTION 3
TRANSFER BELT UNIT
FUSING SECTION
VERTICAL CONVEYANCE SECTION 2
TRANSFER GUIDE SECTION
ELECTRICAL COMPONENTS
High Voltage Section
ADF unit
TONER BOTTLE DRIVE SECTION
OPERATION PANEL SECTION
DUP REVERSE DRIVE SECTION
CASSETTE SECTION
MAIN DRIVE SECTION 3
Vertical conveyance Section
EXTERNAL PARTS
POWER SUPPLY SECTION
MAIN DRIVE SECTION
PAPER FEED DRIVE SECTION
Детали PAPER FEED DRIVE SECTION
| Деталь: | Brushless motor |
| Парткод: | A2YFM10200 |
| Деталь: | BEARING |
| Парткод: | A00F213900 |
| Деталь: | Mounting Plate /A |
| Парткод: | A0VD248501 |
| Деталь: | CLUTCH |
| Парткод: | A011M20000 |
| Деталь: | PIN |
| Парткод: | 4036301401 |
| Деталь: | Gear 21T |
| Парткод: | A0VD218301 |
| Деталь: | LD Relay harness |
| Парткод: | A6DRN10P01 |
| Деталь: | LD Wiring |
| Парткод: | A6DRN10N00 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | A73JR70011 |
| Деталь: | RAIL |
| Парткод: | A0VD111302 |
| Деталь: | RUBBER FOOT |
| Парткод: | 996305501 |
| Деталь: | GEAR 16T |
| Парткод: | A0VD235700 |
| Деталь: | GEAR 16T |
| Парткод: | A0VD235400 |
| Деталь: | Gear 16/26T |
| Парткод: | A0VD235600 |
| Деталь: | Gear 22/30T |
| Парткод: | A0VD235900 |
| Деталь: | GEAR 16/16T |
| Парткод: | A0VD235500 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD362702 |
| Деталь: | LEVER |
| Парткод: | A0VD362602 |
| Деталь: | Drive Holder |
| Парткод: | A0VD235101 |
| Деталь: | COVER |
| Парткод: | A0VD108703 |
| Деталь: | Hold Holder |
| Парткод: | A0VD136701 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140051 |
| Деталь: | Scatteringprevention Seal |
| Парткод: | A0VD109400 |
| Деталь: | STOPPER |
| Парткод: | A0VD107401 |
| Деталь: | Waste Toner Bottle |
| Парткод: | A1AU0Y1 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD107500 |
| Деталь: | SPACER |
| Парткод: | A0VD109001 |
| Деталь: | OPTICAL UNIT |
| Парткод: | A6DTPP0W00 |
| Деталь: | FlatCable |
| Парткод: | A6DTPP0N00 |
| Деталь: | Guide Film |
| Парткод: | A6DTPP0X00 |
| Деталь: | CIS ASSY |
| Парткод: | A6DTPP0P00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A6DTPP0J00 |
| Деталь: | TIMING BELT |
| Парткод: | A2YFPP5800 |
| Деталь: | PULLEY ASSY |
| Парткод: | A2YFPP1500 |
| Деталь: | SHAFT |
| Парткод: | A6DTPP0R00 |
| Деталь: | FRAME |
| Парткод: | A6DTPP0Q00 |
| Деталь: | PLATE SPRING |
| Парткод: | A6DTPP0V00 |
| Деталь: | TAPE |
| Парткод: | A6DTPP0U00 |
| Деталь: | FlatCable |
| Парткод: | A6DTPP0S00 |
| Деталь: | FERRITECORE |
| Парткод: | A6DTPP0T00 |
| Деталь: | DRIVING ASSY |
| Парткод: | A6DTPP0K00 |
| Деталь: | EARTH GROUND |
| Парткод: | A6DTPP0M00 |
| Деталь: | Cover/IR Assy |
| Парткод: | A6DTPP0F00 |
| Деталь: | LABEL Scale |
| Парткод: | A6DTPP0G00 |
| Деталь: | LABEL |
| Парткод: | A3EW944600 |
| Деталь: | Label Prohibit |
| Парткод: | A121944700 |
| Деталь: | Cover/Upper Assy |
| Парткод: | A6DTPP0200 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | A6DTPP0800 |
| Деталь: | TAKE-UP ROLLER |
| Парткод: | A6DTPP0700 |
| Деталь: | ADF Guide Assy |
| Парткод: | A6DTPP0000 |
| Деталь: | Separating Pad |
| Парткод: | A6DTPP0500 |
| Деталь: | GUIDE ASSY |
| Парткод: | A6DTPP0C00 |
| Деталь: | ROLLER |
| Парткод: | A6DTPP0D00 |
| Деталь: | ROLLER |
| Парткод: | A6DTPP0900 |
| Деталь: | ROLLER |
| Парткод: | A6DTPP0A00 |
| Деталь: | DUP Transport Assy |
| Парткод: | A0VDR71722 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | GEAR 16T |
| Парткод: | A0VD235301 |
| Деталь: | ROLL |
| Парткод: | 4138352802 |
| Деталь: | BUSHING |
| Парткод: | A0VD702300 |
| Деталь: | BUSHING |
| Парткод: | 4138353202 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD702501 |
| Деталь: | ROLLER |
| Парткод: | A3GN702100 |
| Деталь: | ROLLER |
| Парткод: | A0VD702902 |
| Деталь: | LEVER |
| Парткод: | A0VD704700 |
| Деталь: | GEAR 32T |
| Парткод: | A0VD704400 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A034563800 |
| Деталь: | Gear 35/42T |
| Парткод: | A0VD704300 |
| Деталь: | GEAR 35T |
| Парткод: | A0VD705101 |
| Деталь: | GEAR 15T |
| Парткод: | A0VD703001 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD703700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD705303 |
| Деталь: | CLUTCH |
| Парткод: | A011M20000 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD703501 |
| Деталь: | GEAR 28T |
| Парткод: | A0VD704900 |
| Деталь: | BUSHING |
| Парткод: | A0VD702400 |
| Деталь: | GEAR 18T |
| Парткод: | A0VD705200 |
| Деталь: | SEAL |
| Парткод: | A034220100 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A034213400 |
| Деталь: | PAPERFEED SOLENOID |
| Парткод: | A034M20000 |
| Деталь: | HOLDER |
| Парткод: | A0VD111700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD111600 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD114101 |
| Деталь: | Torsion Coil spring /Rear |
| Парткод: | A0VD110500 |
| Деталь: | TRANSFER UNIT |
| Парткод: | A1480Y1 |
| Деталь: | RAIL /FRONT |
| Парткод: | A0VD110104 |
| Деталь: | CONTACT |
| Парткод: | A0VD136800 |
| Деталь: | Torsion Coil spring /Front |
| Парткод: | A0VD110400 |
| Деталь: | Hold Holder /ASSY |
| Парткод: | A6DR134100 |
| Деталь: | RAIL |
| Парткод: | A0VD112000 |
| Деталь: | RAIL |
| Парткод: | A0VD111203 |
| Деталь: | Photoconductor Wiring |
| Парткод: | A6DRN10A00 |
| Деталь: | Holder /Front |
| Парткод: | A0VD111402 |
| Деталь: | SHUTTER |
| Парткод: | A0VD362300 |
| Деталь: | SEAL |
| Парткод: | A0VD362201 |
| Деталь: | SEAL |
| Парткод: | A0VD362400 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD362500 |
| Деталь: | RAIL /REAR |
| Парткод: | A0VD110205 |
| Деталь: | DUCT |
| Парткод: | A0VD111502 |
| Деталь: | SEAL |
| Парткод: | A0VD115100 |
| Деталь: | SEAL |
| Парткод: | A0VD115301 |
| Деталь: | SEAL |
| Парткод: | A0VD115200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD214700 |
| Деталь: | SEAL |
| Парткод: | A0VD363700 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | GUIDE |
| Парткод: | A121902500 |
| Деталь: | Label Hi-Temp Caution/Jam |
| Парткод: | A3GN948300 |
| Деталь: | Label JAM |
| Парткод: | A0VD949100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD892400 |
| Деталь: | GUIDE |
| Парткод: | A0VD908101 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | A0VD890102 |
| Деталь: | Paper exit Roll |
| Парткод: | A3GN890301 |
| Деталь: | SPRING |
| Парткод: | A0VD890200 |
| Деталь: | ACTUATOR |
| Парткод: | A0VD907300 |
| Деталь: | LEVER |
| Парткод: | A121893002 |
| Деталь: | Fusing Unit (100V) |
| Парткод: | A148002 |
| Деталь: | Fusing Unit (110-127V) |
| Парткод: | A148010 |
| Деталь: | Fusing Unit (220-240V) |
| Парткод: | A148022 |
| Деталь: | Fixing Relay harness /A |
| Парткод: | A6DTN10H00 |
| Деталь: | ACTUATOR |
| Парткод: | A2YF891202 |
| Деталь: | Paper exit Holder |
| Парткод: | A6DT890300 |
| Деталь: | Paper exit Holder |
| Парткод: | A6DT891100 |
| Деталь: | Paper exit Holder |
| Парткод: | A6DT895300 |
| Деталь: | Gear 38/40T |
| Парткод: | A0VD890800 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | SHAFT |
| Парткод: | A0VD162101 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A0VD701701 |
| Деталь: | 2nd Transfer Roller |
| Парткод: | A1480Y2 |
| Деталь: | Lever /Front |
| Парткод: | A0VD163600 |
| Деталь: | Lever /Rear |
| Парткод: | A0VD163400 |
| Деталь: | GUIDE |
| Парткод: | A0VD161600 |
| Деталь: | ACTUATOR |
| Парткод: | A0VD700202 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD700302 |
| Деталь: | COVER |
| Парткод: | A2YF160601 |
| Деталь: | Label 1 |
| Парткод: | A6DT941100 |
| Деталь: | GUIDE |
| Парткод: | A0VD706400 |
| Деталь: | CONTACT |
| Парткод: | A0VD706300 |
| Деталь: | Photo sensing |
| Парткод: | A0VDM50000 |
| Деталь: | HOLDER |
| Парткод: | A0VD706500 |
| Деталь: | Sensor Wiring |
| Парткод: | A6DRN10D00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD706203 |
| Деталь: | COVER |
| Парткод: | A0VD706102 |
| Деталь: | Sensor Wiring |
| Парткод: | A6DRN10C00 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A0VDM50100 |
| Деталь: | GUIDE |
| Парткод: | A6DT707300 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD707201 |
| Деталь: | ACTUATOR |
| Парткод: | A6DT707100 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | GUIDE |
| Парткод: | A0VD707501 |
| Деталь: | Timing Roller Guide |
| Парткод: | A6DTR70200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A6DR132800 |
| Деталь: | Paperfeed Relay harness |
| Парткод: | A6DRN10F00 |
| Деталь: | Hold Holder |
| Парткод: | A0VD136100 |
| Деталь: | AC Wiring |
| Парткод: | A6DRN10X00 |
| Деталь: | Memory Board (JP) |
| Парткод: | A6DTR70400 |
| Деталь: | Memory Board (WW) |
| Парткод: | A6DTR70300 |
| Деталь: | Reinforce Plate /Left |
| Парткод: | A6DR133600 |
| Деталь: | ROCKER SWITCH |
| Парткод: | A034M60200 |
| Деталь: | AC Wiring |
| Парткод: | A6DRN10000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A6DR132900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A6DT132500 |
| Деталь: | PWB Assembly |
| Парткод: | A6DTH01004 |
| Деталь: | SEAL |
| Парткод: | A6DR133901 |
| Деталь: | LD Flatcable |
| Парткод: | A6DRN10S00 |
| Деталь: | Controller FlatCable |
| Парткод: | A6DRN10T00 |
| Деталь: | SHIELD PLATE |
| Парткод: | A6DR133401 |
| Деталь: | PWB Assembly (PRCB) |
| Парткод: | A6DTH00102 |
| Деталь: | COVER |
| Парткод: | A6DR132400 |
| Деталь: | HIGH VOLTAGE UNIT |
| Парткод: | A0VDM40402 |
| Деталь: | HV Flatcable |
| Парткод: | A6DRN11100 |
| Деталь: | Duct /2 |
| Парткод: | A0VD139401 |
| Деталь: | SEAL |
| Парткод: | A0VD139500 |
| Деталь: | SHEET |
| Парткод: | A0VD134500 |
| Деталь: | Insulating sheet |
| Парткод: | A6DR134401 |
| Деталь: | ADF UNIT |
| Парткод: | A6DTPP0B00 |
| Деталь: | TRAY ASSY |
| Парткод: | A6DTPP0300 |
| Деталь: | CABLE TIE |
| Парткод: | A0HFPP1900 |
| Деталь: | HINGE |
| Парткод: | A0HFPP4302 |
| Деталь: | COVER ASSY |
| Парткод: | A6DTPP0100 |
| Деталь: | SPONGE |
| Парткод: | A0HFPP1700 |
| Деталь: | PAD ASSY |
| Парткод: | A6DTPP0600 |
| Деталь: | HINGE |
| Парткод: | A0HFPP4400 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0FDPP2K00 |
| Деталь: | COVER/REAR |
| Парткод: | A6DTPP0400 |
| Деталь: | GEAR 29T |
| Парткод: | A0VD236400 |
| Деталь: | GEAR 25T |
| Парткод: | A0VD236601 |
| Деталь: | Drive Holder |
| Парткод: | A0VD236902 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | SHAFT |
| Парткод: | A0VD236500 |
| Деталь: | Toner bottle Drive Assy |
| Парткод: | A6DTR70000 |
| Деталь: | CLUTCH |
| Парткод: | A0VDM20000 |
| Деталь: | STOPPER |
| Парткод: | A0VD237400 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD237800 |
| Деталь: | LABEL |
| Парткод: | A0VD491200 |
| Деталь: | MOUNTING PART |
| Парткод: | A0VD117500 |
| Деталь: | LABEL |
| Парткод: | A0VD491300 |
| Деталь: | Relay Connector |
| Парткод: | A0EDM60001 |
| Деталь: | LABEL |
| Парткод: | A0VD491000 |
| Деталь: | LABEL |
| Парткод: | A0VD491100 |
| Деталь: | Panel Sheet (Japanese) |
| Парткод: | A6DT950800 |
| Деталь: | PANEL SHEET (ENGLISH) |
| Парткод: | A6DT950100 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A2YFPP1700 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A2YFPP1600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A2YF161701 |
| Деталь: | COVER |
| Парткод: | A2YF138300 |
| Деталь: | CABLE |
| Парткод: | A6DRN12100 |
| Деталь: | DUCT |
| Парткод: | A2YF105300 |
| Деталь: | SEAL |
| Парткод: | A2YF105400 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313130051 |
| Деталь: | Gear 23T |
| Парткод: | A0VD822800 |
| Деталь: | GEAR 19T |
| Парткод: | A0VD822700 |
| Деталь: | Torque limiter ASSY |
| Парткод: | A3GN823500 |
| Деталь: | Cooling Wiring |
| Парткод: | A6DRN10K00 |
| Деталь: | Conveyance Wiring |
| Парткод: | A6DRN10R00 |
| Деталь: | GEAR 18T |
| Парткод: | A0VD822400 |
| Деталь: | CLUTCH |
| Парткод: | A0VDM20000 |
| Деталь: | ROLL |
| Парткод: | A0VD820200 |
| Деталь: | Reverse/exit Roller |
| Парткод: | A0VD820103 |
| Деталь: | GUIDE |
| Парткод: | A0VD825600 |
| Деталь: | FERRITECORE |
| Парткод: | A2YFM70500 |
| Деталь: | LOUDSPEAKER |
| Парткод: | 4040M40100 |
| Деталь: | DUCT |
| Парткод: | A6DT133502 |
| Деталь: | Neutralizing Brush |
| Парткод: | A0VD894100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A121820800 |
| Деталь: | DUP Reverse Drive Assy |
| Парткод: | A2YFR70211 |
| Деталь: | GEAR 14T |
| Парткод: | A0VD821100 |
| Деталь: | Guide /Upper |
| Парткод: | A0VD820403 |
| Деталь: | Relay harness |
| Парткод: | A6DTN12200 |
| Деталь: | CONTACT |
| Парткод: | A0VD820900 |
| Деталь: | SPACER |
| Парткод: | A6DR819900 |
| Деталь: | BUSHING |
| Парткод: | 4138324401 |
| Деталь: | CLUTCH |
| Парткод: | 4030303401 |
| Деталь: | ROLLER |
| Парткод: | 4138303202 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4658015106 |
| Деталь: | HOLDER |
| Парткод: | A0VD621100 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD624800 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4131305601 |
| Деталь: | GUIDE |
| Парткод: | 4131305702 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0VD623101 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD623200 |
| Деталь: | CASSETTE ASSY |
| Парткод: | A0VDR72511 |
| Деталь: | Label Prohibition inkjet media |
| Парткод: | 4138731601 |
| Деталь: | Cleaning Part |
| Парткод: | A0VD108902 |
| Деталь: | LOCK LEVER |
| Парткод: | A0VD622102 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1164306201 |
| Деталь: | Label 2 |
| Парткод: | A121943200 |
| Деталь: | Label Paper Direction |
| Парткод: | A2YF945100 |
| Деталь: | Brushless motor |
| Парткод: | A2YFM10200 |
| Деталь: | Manual Feed Tray Unit |
| Парткод: | A0VDR71600 |
| Деталь: | TRAY |
| Парткод: | A0VD561700 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4138325501 |
| Деталь: | MANUAL PAPER FEED ASSY |
| Парткод: | A0VDR71300 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD561301 |
| Деталь: | GUIDE |
| Парткод: | A0VD561800 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4131305601 |
| Деталь: | ROLLER |
| Парткод: | 4138303202 |
| Деталь: | CLUTCH |
| Парткод: | 4030303401 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD624800 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4658015106 |
| Деталь: | HOLDER |
| Парткод: | A0VD621100 |
| Деталь: | Open/close Stopper |
| Парткод: | A0VD162300 |
| Деталь: | Vertical Conveyance Assy |
| Парткод: | A6DTR70100 |
| Деталь: | Label Prohibition inkjet media |
| Парткод: | 4138731601 |
| Деталь: | Bypass Tray |
| Парткод: | A0VD560202 |
| Деталь: | TORSION SPRING |
| Парткод: | 4138325201 |
| Деталь: | STOPPER |
| Парткод: | A0VD168200 |
| Деталь: | Label Paper Direction |
| Парткод: | A2YF945200 |
| Деталь: | COVER |
| Парткод: | A6DR160903 |
| Деталь: | COVER |
| Парткод: | A6DT163001 |
| Деталь: | Cover /Right rear |
| Парткод: | A6DT160300 |
| Деталь: | COVER |
| Парткод: | A0VD166501 |
| Деталь: | TRAY |
| Парткод: | A2YF161800 |
| Деталь: | COVER |
| Парткод: | A2YF160102 |
| Деталь: | GROUND PLATE |
| Парткод: | A2YF138800 |
| Деталь: | COVER |
| Парткод: | A02E167800 |
| Деталь: | Cover /Right front |
| Парткод: | A2YF160501 |
| Деталь: | COVER |
| Парткод: | A0VD166401 |
| Деталь: | Label bizhub C3110 |
| Парткод: | A6DT941800 |
| Деталь: | LABEL LOGO MARK |
| Парткод: | A00F942000 |
| Деталь: | Label Emperon |
| Парткод: | A011946200 |
| Деталь: | Cover /Front |
| Парткод: | A2YF160400 |
| Деталь: | SHEET |
| Парткод: | A6DT942000 |
| Деталь: | SHEET |
| Парткод: | A0VD941801 |
| Деталь: | COVER |
| Парткод: | A6DT160200 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | Cooling Duct |
| Парткод: | A6DR102200 |
| Деталь: | Toner Detection harness |
| Парткод: | A6DRN10200 |
| Деталь: | Protection Cover |
| Парткод: | A121104101 |
| Деталь: | Detecting Part |
| Парткод: | A0VD135512 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Hold Holder |
| Парткод: | A0VD135317 |
| Деталь: | Adjusting Spring |
| Парткод: | A0VD135201 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD135402 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06M60100 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A0VDM50200 |
| Деталь: | DC Power source harness |
| Парткод: | A6DTN10100 |
| Деталь: | DC Power source (100-127V) |
| Парткод: | A6DRM40001 |
| Деталь: | DC Power source (220-240V) |
| Парткод: | A6DRM40101 |
| Деталь: | FRAME |
| Парткод: | A2YF133100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A6DR103001 |
| Деталь: | SEAL |
| Парткод: | A121102600 |
| Деталь: | SEAL |
| Парткод: | A0VD139700 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | Wiring Guide /1 |
| Парткод: | A2YF138501 |
| Деталь: | SHEET |
| Парткод: | A2YF139000 |
| Деталь: | SPACER |
| Парткод: | V502010021 |
| Деталь: | Brushless motor |
| Парткод: | A2YFM10000 |
| Деталь: | Main body Drive harness |
| Парткод: | A6DRN10500 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD220300 |
| Деталь: | BUSHING |
| Парткод: | A0VD220201 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD219800 |
| Деталь: | HOLD PLATE |
| Парткод: | A0VD211303 |
| Деталь: | PAPER FEED DRIVE ASSY |
| Парткод: | A6DRR70000 |
| Деталь: | CLUTCH |
| Парткод: | A02EM20000 |
| Деталь: | GEAR 22T |
| Парткод: | A0VD231200 |
| Деталь: | GEAR 25T |
| Парткод: | A0VD230901 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD233301 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | LEVER |
| Парткод: | A0VD624100 |
| Деталь: | HOLDER |
| Парткод: | 4002312303 |
| Деталь: | Paperfeed Wiring |
| Парткод: | A6DRN10E00 |
| Деталь: | Guide Sheet |
| Парткод: | A3GN217000 |
Коды ошибок
0010
0017
0018
004A
004E
0094
0096
0101
0300
0310
0315
0500
0502
0503
0510
0520
0F52
0F53
0F54
0F55
13C4
13C5
13C6
13C7
13CB
13CC
13CD
13CE
13DD
13E2
13E3
13F0
3C00
3C10
6751
6790
6791
6792
6793
9401
C151
C161
D004
D091
D092
D093
D094
D095
D096
D0A2
D0A3
D0A4
D0A5
D0A6
D3A2
D3F1
D3F2
D3F3
D3F4
D501
FB00 ... FBA5
Описание
| Error code: | 0010 |
| Display: | P MOTOR 1 |
| Description: | Network I/F Initialize has not been completed. |
| Causes: | Network I/F does not work correctly. Firmware for Network I/F is not installed. |
| Remedy: | Check the firmware is installed into Network I/F. Main Board replacement |
| Error code: | 0017 |
| Display: | P MOTOR 2 |
| Description: | Intermediate transport motor malfunction • The intermediate transport motor does not rotate evenly even after the lapse of a given period of time while it is being started. • The motor lock signal remains HIGH for a given period of consecutive time while the intermediate transport motor is being rotated. |
| Causes: | • Transport motor (M2) • Printer control board (PRCB) |
| Remedy: | 1 Check the M3 connector for proper connection and correct as necessary. 2 Check M3 for proper drive coupling and correct as necessary. 3 Check the MFPB connector for proper connection and correct as necessary. 4 M3 operation check MFPB PJ27MFPB-3 to 7 C-5. 5 Change M3. 6 Change MFPB. 7 Change DCPU. |
| Error code: | 0018 |
| Display: | D MOTOR 2 |
| Description: | Color PC Drum Motor’s failure to turn • The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning. |
| Causes: | • Developing motor (M1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector of motor for proper connection and correct as necessary. 2 Check the connector of motor for proper drive coupling and correct as necessary. 3 Check the PWB-M connector for proper connection and correct as necessary. 4 M2 operation check PWB-M CNDM3-5 (REM) PWB-M CNDM3-8 (LOCK) C-23. 5 Change PWB-M. |
| Error code: | 004A |
| Display: | Duplex fan failure CODE (004A) Turn power off, on |
| Description: | Duplex Unit Fan Failure The Duplex Unit Fan Motor lock signal remains HIGH for a predetermined consecutive period of time while the cooling fan motor remains energized. |
| Causes: | • Engine Control Board, PL13.0.20 • Duplex Unit, PL14.1 |
| Remedy: | 1 Check the Engine Control Board connector P/J21. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Replace the Engine Control Board. Does the problem persist? Go to step 3. Complete. 3 Replace the Duplex Unit. Complete. |
| Error code: | 004E |
| Display: | LVPS fan failure CODE (004E) Turn power off, on |
| Description: | LVPS Fan Failure • The Power Supply Cooling Fan Motor does not rotate evenly even after the lapse of a given period of time while it is being started. • The motor lock signal remains HIGH for a given period of consecutive time while the Power Supply Cooling Fan Motor is being rotated. |
| Causes: | • Power Supply Cooling Fan Motor, PL12.0.11 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check the High Voltage Board connectors CN1 and CN2, and the Engine Control Board connector P/J17. Are the connectors seated properly? Go to step 2. Reseat the connector(s). If the problem persists, go to step 2. 2 Check the Power Supply Cooling Fan Motor control signals at CN2. Are the signals operating correctly? Replace the motor. If the problem persists, go to step 3. Go to step 3. 3 Check the Power Supply Cooling Fan Motor control signals at PJ17 on the Engine Control Board. Are the control signals operating correctly? Replace the High Voltage Board. If the problem persists, go to step 4. Go to step 4. 4 On the Engine Control Board, check for +24 VDC at P/J2-1, 5, and 7. Check for +5 VDC at P/J2-2. Are the voltages present and within specification? Go to step 5. Replace the Power Supply. If the problem persists, go to step 5. 5 Replace the Engine Control Board. Complete. |
| Error code: | 0094 |
| Display: | Trans. roll failure CODE (0094) Turn power off, on |
| Description: | Transfer Roll Failure Possible causes: • The 2nd Image Transfer Retraction Position Sensor(PS3) is not activated (retracted position) within a given period of time after the retraction sequence of the 2nd transfer roller has been started. • The 2nd Image Transfer Retraction Position Sensor is not deactivated (pressed position) within a given period of time after the pressure sequence of the 2nd transfer roller has been started. |
| Causes: | • 2nd Image Transfer Retraction Position Sensor (PS3), PL4.0.9 • 2nd Image Transfer Retraction Position Solenoid (SD4), PL7.2.23 • Main Motor, PL9.1.6 • Engine Control Board, PL13.0.20 |
| Remedy: | 1 Check the Main Motor connector CN37. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the Main Motor for proper drive coupling and correct as necessary. Does the problem persist? Go to step 3. Complete. 3 Check the 2nd Image Transfer Retraction Position Solenoid connector CN5. Is the connector seated properly? Go to step 4. Reseat the connector. If the problem persists, go to step 4. 4 Check the 2nd Image Transfer Retraction Position Solenoid for proper drive coupling and correct as necessary. Does the problem persist? Go to step 5. Complete. 5 Check the 2nd Image Transfer Retraction Position Sensor control signal for a voltage change at P/J12-3 on the Engine Control Board. Is the signal operating correctly? Go to step 6. Replace the Engine Control Board. If the problem persists, go to step 6. 6 Replace the 2nd Image Transfer Retraction Position Solenoid. Does the problem persist? Go to step 7. Complete. 7 Replace the 2nd Image Transfer Retraction Position Sensor. Complete. |
| Error code: | 0096 |
| Display: | XFER DETACH 1 |
| Description: | Transfer Belt Separation • The 1st Image Transfer Pressure/Retraction Position Sensor doesn’t turn ON (Retracting) even after the lapse of a given period of time after the 1st Image Transfer Pressure/Retraction Clutch has turned ON during the Transfer Belt is retracting. • The 1st Image Transfer Pressure/Retraction Position Sensor doesn’t turn OFF (Pressuring) even after the lapse of a given period of time after the 1st Image Transfer Pressure/Retraction Clutch has turned ON during the Transfer Belt is pressuring. |
| Causes: | • 1st transfer pressure sensor (PS17) • Transport motor (M2) • 1st transfer pressure solenoid (SD1) • Printer control board (PRCB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 PC6 I/O check, Sensor check 3 CL3 operation check PWB-M CNDM1-11 (ON) K to L-2. 4 M1 operation check PWB-M CNDM1-5 (REM) PWB-M CNDM1-8 (LOCK) K to L-2. 5 Change PWB-M. |
| Error code: | 0101 |
| Display: | MAINTENANCE CALL 0101 |
| Description: | Limit Position Initialize in the Service Mode has not been done. |
| Causes: | Limit Position Initialize has not been done. Limit Position Initialize is ended before it is completed. |
| Remedy: | Complete Limit Position Initialize correctly. |
| Error code: | 0300 |
| Display: | POLYGON MOTOR |
| Description: | Polygon motor malfunction |
| Causes: | • The polygon motor does not rotate evenly even after the lapse of a given period of time after it has been started. • The motor lock signal remains HIGH for a given period of consecutive time while the polygon motor is being rotated. |
| Remedy: | 1 Check the cable and connector for proper connection and correct as necessary. - - 2 Change PH unit. - - 3 Change PRCB. - - |
| Error code: | 0310 |
| Display: | LASER ERROR |
| Description: | Laser malfunction |
| Causes: | • The SOS signal is not detected within a given period of time after the output of the laser has been started. |
| Remedy: | 1 Check the cable and connector for proper connection and correct as necessary. - - 2 Change PH unit. - - 3 Change PRCB. - - |
| Error code: | 0315 |
| Description: | PH board communication error • Mismatching of data being written and read occurs continuously for certain times during communication with the PH board. • The EEPROM of the PH board is not yet initialized. |
| Causes: | • Front door sensor (PS10) • Right door sensor (PS11) • Front door switch (SW2) • Right door switch (SW3) • DC power supply (DCPU) • Printer control board (PRCB) • MFP board (MFPB) • PH unit |
| Remedy: | 1 Check the connector between PRCB CN18-relay CN63-PH unit for proper connection and correct as necessary. 2 Replace the PH unit. 3 Replace PRCB. |
| Error code: | 0500 |
| Display: | FUSER ERROR |
| Description: | Fuser warm-up failure |
| Causes: | • The thermistor /1 does not detect the specified temperature and the warm-up cycle is not completed even after the lapse of a given period of time after the cycle has been started. |
| Remedy: | 1 Change fuser unit. - - 2 For C110: 1. Main switch is turned ON. 2. Open the top cover. 3. Press the following keys in this order. ROTATE TONER key -ATTENTION key - ATTENTION key - ROTATE TONER key. 4. Main switch is turned OFF/ON. For C130n: 1. Main switch is turned ON. 2. Execute [SERVICE MENU] - [FUSER UNLOCK]. See P.103 - - 3 Change PRCB. - - 4 Change DCPU. - - |
| Error code: | 0502 |
| Display: | Thermistor failure CODE (0502) Turn power off, on |
| Description: | 0502 Thermistor Failure, 0510 Fuser Failure, and 0520 Fuser Failure 0502 Thermistor Failure The temperature detected by the thermistor does not reach an expected level after the warm-up cycle starts. |
| Causes: | • Fuser, PL4.0.13 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check that the Fuser is installed correctly. Does the problem persist? Go to step 2. Complete. 2 Check the Engine Control Board connectors P/J2, P/J3, and P/J6. Are the connectors seated properly? Go to step 3 Reseat the connectors. If the problem persists, go to step 3. 3 Check the Low Voltage Power Supply connectors CN3, CN5, and CN7. Are the connectors seated properly? Go to step 4. Reseat the connectors. If the problem persists, go to step 4. 4 Replace the Fuser (8-9). Does the problem persist? Go to step 5. Complete. 5 Replace the Engine Control Board. Does the problem persist? Go to step 6. Complete. 6 Replace the Power Supply. Complete. |
| Error code: | 0503 |
| Display: | TERMISTOR2 |
| Description: | Thermistor resistance failure |
| Causes: | • The difference between the temperature detected by thermistor/1 and that detected by thermistor/2 exceeds a predetermined value. |
| Remedy: | 1 Change fuser unit. - - 2 For C110: 1. Main switch is turned ON. 2. Open the top cover. 3. Press the following keys in this order. ROTATE TONER key -ATTENTION key - ATTENTION key - ROTATE TONER key. 4. Main switch is turned OFF/ON. For C130n: 1. Main switch is turned ON. 2. Execute [SERVICE MENU] - [FUSER UNLOCK]. See P.103 - - 3 Change PRCB. - - 4 Change DCPU. - - |
| Error code: | 0510 |
| Display: | Fuser failure CODE (0510) Turn power off, on |
| Description: | 0502 Thermistor Failure, 0510 Fuser Failure, and 0520 Fuser Failure 0510 Fuser Failure The temperature detected by the thermistor remains lower than expected for a given period of time or longer. |
| Causes: | • Fuser, PL4.0.13 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check that the Fuser is installed correctly. Does the problem persist? Go to step 2. Complete. 2 Check the Engine Control Board connectors P/J2, P/J3, and P/J6. Are the connectors seated properly? Go to step 3 Reseat the connectors. If the problem persists, go to step 3. 3 Check the Low Voltage Power Supply connectors CN3, CN5, and CN7. Are the connectors seated properly? Go to step 4. Reseat the connectors. If the problem persists, go to step 4. 4 Replace the Fuser (8-9). Does the problem persist? Go to step 5. Complete. 5 Replace the Engine Control Board. Does the problem persist? Go to step 6. Complete. 6 Replace the Power Supply. Complete. |
| Error code: | 0520 |
| Display: | Fuser failure CODE (0520) Turn power off, on |
| Description: | 0502 Thermistor Failure, 0510 Fuser Failure, and 0520 Fuser Failure 0520 Fuser Failure The temperature detected by the thermistor remains higher than expected for a given period of time or longer. |
| Causes: | • Fuser, PL4.0.13 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check that the Fuser is installed correctly. Does the problem persist? Go to step 2. Complete. 2 Check the Engine Control Board connectors P/J2, P/J3, and P/J6. Are the connectors seated properly? Go to step 3 Reseat the connectors. If the problem persists, go to step 3. 3 Check the Low Voltage Power Supply connectors CN3, CN5, and CN7. Are the connectors seated properly? Go to step 4. Reseat the connectors. If the problem persists, go to step 4. 4 Replace the Fuser (8-9). Does the problem persist? Go to step 5. Complete. 5 Replace the Engine Control Board. Does the problem persist? Go to step 6. Complete. 6 Replace the Power Supply. Complete. |
| Error code: | 0F52 |
| Display: | TE SENSOR Y |
| Description: | Toner level sensor /Y malfunction • An error occurs on the toner level sensor board (TLSB). |
| Causes: | • Toner level sensor/Y (PS13) • Printer control board (PRCB) |
| Remedy: | 1 Check the TLSB and MFPB for proper connection and correct as necessary. 2 Change TLSB. 3 Change MFPB. |
| Error code: | 0F53 |
| Display: | TE SENSOR M |
| Description: | Toner level sensor /M malfunction • An error occurs on the toner level sensor board (TLSB). |
| Causes: | • Toner level sensor/M (PS14) • Printer control board (PRCB) |
| Remedy: | 1 Check the TLSB and MFPB for proper connection and correct as necessary. 2 Change TLSB. 3 Change MFPB. |
| Error code: | 0F54 |
| Display: | TE SENSOR C |
| Description: | Toner level sensor /C malfunction • An error occurs on the toner level sensor board (TLSB). |
| Causes: | • Toner level sensor/C (PS15) • Printer control board (PRCB) |
| Remedy: | 1 Check the TLSB and MFPB for proper connection and correct as necessary. 2 Change TLSB. 3 Change MFPB. |
| Error code: | 0F55 |
| Display: | TE SENSOR K |
| Description: | Toner level sensor /K malfunction • An error occurs on the toner level sensor board (TLSB). |
| Causes: | • Toner level sensor/K (PS16) • Printer control board (PRCB) |
| Remedy: | 1 Check the TLSB and MFPB for proper connection and correct as necessary. 2 Change TLSB. 3 Change MFPB. |
| Error code: | 13C4 |
| Description: | Imaging unit/C new article release. The status with the new unit is not cleared continuously for 3 times after the new imaging unit is set. |
| Causes: | • Imaging unit/C • Printer control board (PRCB) |
| Remedy: | 1 Reinstall the imaging unit. 2 Check the connector between imaging unit-PRCB CN221 for proper connection and correct as necessary. 3 Replace the imaging unit. 4 Replace PRCB. |
| Error code: | 13C5 |
| Description: | Imaging unit/M new article release. The status with the new unit is not cleared continuously for 3 times after the new imaging unit is set. |
| Causes: | • Imaging unit/M • Printer control board (PRCB) |
| Remedy: | 1 Reinstall the imaging unit. 2 Check the connector between imaging unit-PRCB CN221 for proper connection and correct as necessary. 3 Replace the imaging unit. 4 Replace PRCB. |
| Error code: | 13C6 |
| Description: | Imaging unit/Y new article release. The status with the new unit is not cleared continuously for 3 times after the new imaging unit is set. |
| Causes: | • Imaging unit/Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall the imaging unit. 2 Check the connector between imaging unit-PRCB CN221 for proper connection and correct as necessary. 3 Replace the imaging unit. 4 Replace PRCB. |
| Error code: | 13C7 |
| Description: | Imaging unit/K new article release. The status with the new unit is not cleared continuously for 3 times after the new imaging unit is set. |
| Causes: | • Imaging unit/K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall the imaging unit. 2 Check the connector between imaging unit-PRCB CN221 for proper connection and correct as necessary. 3 Replace the imaging unit. 4 Replace PRCB. |
| Error code: | 13CB |
| Description: | Toner cartridge/C new release failure. The status with the new cartridge is not cleared continuously for 3 times after the new toner cartridge is set. |
| Causes: | • Toner cartridge/C • Printer control board (PRCB) |
| Remedy: | 1 Reinstall the toner cartridge. 2 Check the connector between toner cartridge-PRCB CN82 for proper connection and correct as necessary. 3 Replace the toner cartridge. 4 Replace PRCB. |
| Error code: | 13CC |
| Description: | Toner cartridge/M new release failure. The status with the new cartridge is not cleared continuously for 3 times after the new toner cartridge is set. |
| Causes: | • Toner cartridge/M • Printer control board (PRCB) |
| Remedy: | 1 Reinstall the toner cartridge. 2 Check the connector between toner cartridge-PRCB CN82 for proper connection and correct as necessary. 3 Replace the toner cartridge. 4 Replace PRCB. |
| Error code: | 13CD |
| Description: | Toner cartridge/Y new release failure. The status with the new cartridge is not cleared continuously for 3 times after the new toner cartridge is set. |
| Causes: | • Toner cartridge/Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall the toner cartridge. 2 Check the connector between toner cartridge-PRCB CN82 for proper connection and correct as necessary. 3 Replace the toner cartridge. 4 Replace PRCB. |
| Error code: | 13CE |
| Description: | Toner cartridge/K new release failure. The status with the new cartridge is not cleared continuously for 3 times after the new toner cartridge is set. |
| Causes: | • Toner cartridge/K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall the toner cartridge. 2 Check the connector between toner cartridge-PRCB CN82 for proper connection and correct as necessary. 3 Replace the toner cartridge. 4 Replace PRCB. |
| Error code: | 13DD |
| Display: | Initial toner failed CODE (13DD) Replace toner Contact Xerox for unit exchange |
| Description: | Initial Toner Failure The printer determines that an initial toner cartridge has been installed. The printer is programmed to only use initial toner cartridges one time. |
| Remedy: | Install a Xerox Standard or High Capacity cartridge. |
| Error code: | 13E2 |
| Display: | Engine ROM failure CODE (13E2) Turn power off, on |
| Description: | Engine ROM Failure Flash ROM writing is found faulty during a check. |
| Causes: | • Engine Control Board, PL13.0.20 • Image Processor Board, PL2.0.4 |
| Remedy: | 1 Check the Engine Control Board connectors. Are the connectors seated properly? Go to step 2. Reseat the connectors. If the problem persists, go to step 2. 2 Replace the Engine Control Board. Does the problem persist? Go to step 3. Complete. 3 Replace the Image Processor Board. Complete. |
| Error code: | 13E3 |
| Display: | FLASH DEVICE |
| Description: | Flash ROM device fault • An erase error occurs during erasing of data in flash ROM. |
| Causes: | • Printer control board (PRCB) • MFP board (MFPB) |
| Remedy: | 1 Check the MFPB for proper connection and correct as necessary. 2 Change PRCB. 3 Change MFPB. |
| Error code: | 13F0 |
| Display: | ENGINE ERR |
| Description: | Engine control failure |
| Causes: | • An undefined malfunction occurs in the engine section (PRCB, etc.). |
| Remedy: | 1 Check the cable and connector for proper connection and correct as necessary. - - 2 Change PRCB. - - 3 Change MFPB. |
| Error code: | 3C00 |
| Display: | Eng. EEPROM failure CODE (3C00) Turn power off, on |
| Description: | Eng. EEPROM failure |
| Remedy: | Contact a Xerox representative to correct this error. |
| Error code: | 3C10 |
| Display: | Eng. EEPROM failure CODE (3C10) Turn power off, on |
| Description: | Eng. EEPROM failure |
| Remedy: | Contact a Xerox representative to correct this error. |
| Error code: | 6751 |
| Description: | CCD clamp/gain adjustment failure During the CCD gain adjustment, a condition in which the peak value of the output data is equal to, or less than, 64 occurs three consecutive times during retries. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 6790 |
| Description: | AFE offset adjustment error During the offset adjustment, the offset value does not fall within the predetermined range a total of three times including retries. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 6791 |
| Description: | AFE register setting error There is a mismatch between the set default values of the AFE gain/offset and the gain/offset values read thereafter. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 6792 |
| Description: | White reference plate search error The black/white edge on the shading plate cannot be detected during initialization. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 6793 |
| Description: | Scanner communication error A communication error of some sort occurs between the controller and the scanner. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 9401 |
| Description: | Exposure lamp lighting failure detected The intensity of the lamp is not stabilized within a predetermined period of time during the lamp stabilization check process in a lamp warm-up cycle. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 MFPB F102, F105 conduction check - - 7 Replace MFPB |
| Error code: | C151 |
| Description: | ROM contents error upon startup (MSC) A fault is detected in a sequence of ROM contents check of the MFPB during starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace MFPB |
| Error code: | C161 |
| Description: | Firmware update error A firmware updating sequence is not normally terminated. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the cable used for updating the firmware for proper connection and correct any faulty connection as necessary. - - 2 Check the firmware updating file; if the file is not correct, update the firmware again. - - 3 Check the firmware updating procedure; if the procedure is not correct, update the firmware again. 4 Update the firmware again. 5 Check the MFPB connector for proper connection and correct any faulty connection as necessary. 6 Replace MFPB |
| Error code: | D004 |
| Description: | Hard disk access error (connection failure) Unable to communicate between the hard disk and MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace the corresponding board. - - 4 If the above actions do not solve the problem, contact KM. |
| Error code: | D091 |
| Description: | Hard disk full error The area made available as a user area is full during access to the hard disk. |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | 1 Delete jobs saved using [Document Print/ Delete] to thereby increase the portion of the user area available for use. - - 2 Check the hard disk connector MFPB CN5 and CN13 for proper connection and correct any faulty connection as necessary. - - 3 Using [Administrator Settings] -> [Security Settings] -> [HDD Settings] -> [HDD Format], format the HDD. - - 4 Replace the hard disk. - - 5 Replace MFPB. |
| Error code: | D092 |
| Description: | No hard disk (found during a disk check) The hard disk is not mounted.sk |
| Causes: | Hard disk |
| Remedy: | 1 Install and format the hard disk. |
| Error code: | D093 |
| Description: | Wrong hard disk (found during a disk check) • A hard disk intended for another model is mounted. • The hard disk capacity is short. |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | 1 Replace the hard disk. - - 2 Format hard disk. |
| Error code: | D094 |
| Description: | Hard disk check disk error HDD is damaged. |
| Causes: | Hard disk |
| Remedy: | 1 Replace the hard disk. - - 2 Format hard disk. |
| Error code: | D095 |
| Description: | Hard disk recovered (requiring reboot) HDD is damaged. |
| Causes: | Hard disk |
| Remedy: | 1 Turn OFF/ON the main power switch. - - 2 If the above actions do not solve the problem, contact KM. |
| Error code: | D096 |
| Description: | Hard disk access fault HDD is damaged. |
| Causes: | Hard disk |
| Remedy: | 1 Replace the hard disk. - - 2 Format hard disk. |
| Error code: | D0A2 |
| Description: | No SSD board (found during a disk check) The SSD board is not mounted. |
| Causes: | SSD board (SSDB) |
| Remedy: | 1 Install the SSDB. 2 Using [Admin Settings] -> [Security Settings] -> [SSD Settings] -> [SSD Format], format the SSD. |
| Error code: | D0A3 |
| Description: | Wrong SSD board (found during a disk check) • A SSD board intended for another model is mounted. • The SSD board capacity is short. |
| Causes: | SSD board (SSDB) |
| Remedy: | 1 Replace SSDB. 2 Using [Admin Settings] -> [Security Settings] -> [SSD Settings] -> [SSD Format], format the SSD. |
| Error code: | D0A4 |
| Description: | SSD board check disk error When the power switch ON, the SSD board fails to be checked. |
| Causes: | SSD board (SSDB) |
| Remedy: | 1 Using [Admin Settings] -> [Security Settings] -> [SSD Settings] -> [SSD Format], format the SSD. 2 Replace SSDB. 3 Using [Admin Settings] -> [Security Settings] -> [SSD Settings] -> [SSD Format], format the SSD. |
| Error code: | D0A5 |
| Description: | SSD board recovered (requiring reboot) When the power switch ON, the SSD board fails to be recovered. |
| Causes: | SSD board (SSDB) |
| Remedy: | 1 Turn OFF/ON the power switch. 2 Replace SSDB. 3 Using [Admin Settings] -> [Security Settings] -> [SSD Settings] -> [SSD Format], format the SSD. |
| Error code: | D0A6 |
| Description: | SSD board access fault When the power switch ON, the SSD board fails to be access. |
| Causes: | SSD board (SSDB) |
| Remedy: | 1 Replace SSDB. 2 Using [Admin Settings] -> [Security Settings] -> [SSD Settings] -> [SSD Format], format the SSD. |
| Error code: | D3A2 |
| Description: | Counter error A write error occurs in the counter area. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the MFPB for its mounting condition and correct any faulty condition. 2 Replace MFPB 3 If the same trouble code persists after the abovementioned procedures, the EEPROM is probably damaged. |
| Error code: | D3F1 |
| Description: | Occur:The drum counter is over the life limit, and detect toner empty. |
| Remedy: | Push the ONLINE SW when change the new Image Drum. |
| Error code: | D3F2 |
| Description: | Occur:Printing 500 page, after the drum counter is over the life limit, and detect toner empty. |
| Remedy: | Push the SW when change the new Image Drum and Cover open close. |
| Error code: | D3F3 |
| Description: | Write error of the counter area (SSD) An error occurs in the counter area when writing to the EEPROM. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Turn OFF/ON the power switch. 2 Check the MFPB for its mounting condition and correct any faulty condition. 3 Replace MFPB 4 If the same trouble code persists after the abovementioned procedures, replace the EEPROM with the one has been installed on the new board. |
| Error code: | D3F4 |
| Description: | Occur:The drum counter is over the life limit, and detect toner empty. |
| Remedy: | Auto reset when change the new drum. |
| Error code: | D501 |
| Description: | FLASH error The SSD board (SSDB) develops a fault. |
| Causes: | • MFP board (MFPB) • SSD board (SSDB) |
| Remedy: | 1 Check the SSD for its mounting condition and correct any faulty condition. - - 2 Replace MFPB |
| Error code: | FB00 ... FBA5 |
| Description: | Abort code |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Power switch Turn OFF and ON the power switch, and check if the Abort code appears again. NO When not reappearing, continuous use is carried out, and it is checked whether an abort code occurs. 2 Connector connection Check the connector for proper connection on MFPB and correct as necessary. NO It will correct, if connector connection has abnormalities. 3 Firmware Update the firmware to the latest version, and check if the Abort code appears again. NO After conducting firmware updating, check the firmware version No. and confirm that the firmware has been normally updated. 4 MFP board Replace MFPB |
