Konica-Minolta bizhub C3851FS
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A4
Скорость печати
A4
38
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Макс. формат |
A4 |
Размещение |
настольный |
Цветность печати |
цветная |
Печать фотографий |
|
Телефон |
|
Технология печати |
лазерная |
Сканер |
|
Факс |
|
Тип устройства |
МФУ |
Копир |
|
Принтер |
|
Время разогрева |
20 |
Количество цветов |
4 |
Пигментные чернила |
|
Печать без полей |
|
Двусторонняя печать |
|
Макс, разрешение для ч/б печати |
|
| По Y | 1 200 |
| По X | 1 200 |
Скорость ч/б печати |
|
| A4 | 38 |
Копир |
|
Макс, количество копий за цикл |
9 999 |
Шаг масштабирования |
0,1 |
Время выхода первой копии |
6,2 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По Y | 600 |
| По X | 600 |
Сканер |
|
Слайд-адаптер |
|
Макс. формат оригинала |
A4 |
Оттенки серого |
256 |
Тип сканера |
планшетный/протяжный |
Емкость устройства автоподачи оригиналов |
50 |
Устройство автоподачи оригиналов |
двустороннее |
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Разрешение сканера |
|
| По Х | 600 |
Расходные материалы |
|
Ресурс цветного картриджа/тонера |
12 000 |
Ресурс ч/б картриджа/тонера |
13 000 |
Количество картриджей |
4 |
Печать на: |
|
| CD/DVD |
|
| Рулоне |
|
| Матовой бумаге |
|
| Карточках |
|
| Пленках |
|
| Этикетках |
|
| Глянцевой бумаге |
|
Плотность бумаги |
|
| Минимальная | 60 |
| Максимальная | 210 |
Факс |
|
Макс, скорость передачи данных |
33,6 Кбит/с |
Телефон |
|
АОН |
|
Caller ID |
|
Автоответчик |
|
Стандарт DECT |
|
Спикерфон |
|
Проводная трубка |
|
Беспроводная трубка |
|
Шрифты и языки управления |
|
Языки управления |
|
| PostScript 2 |
|
|
|
|
| PostScript |
|
| PCL 6 |
|
| PCL 5c |
|
| PostScript 3 |
|
Количество установленных шрифтов |
|
| PCL | 80 |
| PostScript | 136 |
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Максимальная | 1 650 |
| Стандартная | 650 |
Вывод бумаги |
|
| Максимальный | 250 |
| Стандартный | 250 |
Финишер |
|
Степлер |
|
Брошюровщик |
|
Сортировка со сдвигом |
|
Электронная сортировка |
|
Сортер |
|
Интерфейсы |
|
Wi-Fi |
|
Устройство для чтения карт памяти |
|
LPT |
|
RS-232 |
|
Инфракрасный порт |
|
FireWire (IEEE 1394) |
|
Bluetooth |
|
Версия USB |
2,0 |
Веб-интерфейс |
|
USB |
|
AirPrint |
|
Ethernet (RJ-45) |
|
Поддержка iOS |
|
Память/Процессор |
|
Объем памяти |
2 048 |
Емкость жесткого диска |
250 |
Макс, объем памяти |
4 096 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Диагональ дисплея |
7 |
Экран |
|
Поддержка ОС |
|
| DOS |
|
| Linux |
|
| Windows |
|
| Mac OS |
|
Потребляемая мощность |
|
| При работе | 1 700 |
Габариты |
|
Высота |
603 |
Вес |
53,1 |
Ширина |
555 |
Глубина |
584 |
Модули
Finisher section 6
ELECTRICAL COMPONENTS 2
Auto document feeder section
Finisher section 7
External Parts Section 2
Paper feed section (Manual tray)
PAPER FEED DRIVE SECTION
Finisher section 5
Transfer section (2nd transfer)
SCANNER SECTION
Fusing/ Paper exit section
Paper feed section (Tray 1) 2
External Parts Section
TRANSFER GUIDE SECTION
Toner suction section
Finisher section 2
ELECTRICAL COMPONENTS
Paper feed section (Tray 1)
TONER BOTTLE DRIVE SECTION
Write/ Toner collection section
Finisher section 4
CONTROL PANEL SECTION
Finisher section
Paper feed section (Manual tray) 2
Erase LED section
Cooling fan section
Finisher section 8
Finisher section 3
MAIN DRIVE SECTION
Duplex reverse drive section
Duplex Section
TRANSFER BELT SECTION
Детали TONER BOTTLE DRIVE SECTION
| Деталь: | Slide Guide |
| Парткод: | A63D701701 |
| Деталь: | HOLDER |
| Парткод: | A63D701600 |
| Деталь: | Gear 15/25T |
| Парткод: | A63D701900 |
| Деталь: | HOLDER |
| Парткод: | A63D704300 |
| Деталь: | ROLL |
| Парткод: | A63D705600 |
| Деталь: | CUSHION |
| Парткод: | A63D704500 |
| Деталь: | Regulating Tray /Rear |
| Парткод: | A63D720100 |
| Деталь: | Slide Shaft |
| Парткод: | A63D703900 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A63D704100 |
| Деталь: | Slide Cam |
| Парткод: | A63D701000 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140071 |
| Деталь: | Gear13T |
| Парткод: | A63D701800 |
| Деталь: | Processing Tray |
| Парткод: | A63D703701 |
| Деталь: | Processing Tray |
| Парткод: | A63D703800 |
| Деталь: | Separating Claw |
| Парткод: | A63D722800 |
| Деталь: | CUSHION |
| Парткод: | A63D704400 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D722900 |
| Деталь: | Processing Tray /Front |
| Парткод: | A63D720000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D728200 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Fixing Plate |
| Парткод: | A63D111600 |
| Деталь: | GUIDE RAIL |
| Парткод: | A63D721001 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D721900 |
| Деталь: | Sheet /1 |
| Парткод: | A63D111800 |
| Деталь: | Sheet /2 |
| Парткод: | A63D111900 |
| Деталь: | Sheet /3 |
| Парткод: | A63D171700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN130000 |
| Деталь: | SEAL |
| Парткод: | A92E134800 |
| Деталь: | PCB Support |
| Парткод: | V502010045 |
| Деталь: | SPACER |
| Парткод: | V502010029 |
| Деталь: | SEAL |
| Парткод: | A92E134900 |
| Деталь: | Insulating sheet |
| Парткод: | A3GN136100 |
| Деталь: | DC Power source (220-240V) |
| Парткод: | A3GNM40102 |
| Деталь: | Insulating sheet |
| Парткод: | A3GN136200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E134000 |
| Деталь: | PWB assemble(PWB-MFP) |
| Парткод: | A92EH02102 |
| Деталь: | GUIDE |
| Парткод: | A92E133200 |
| Деталь: | Power source Cable /1 |
| Парткод: | A92EN12000 |
| Деталь: | Power Supply Wiring |
| Парткод: | A92FN10000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E132500 |
| Деталь: | Relay Wiring /2 |
| Парткод: | A92EN10G00 |
| Деталь: | Polygon Relay harness |
| Парткод: | A92EN10700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E132700 |
| Деталь: | Power source Cable /2 |
| Парткод: | A92EN12100 |
| Деталь: | EEPROM |
| Парткод: | V864800076 |
| Деталь: | FERRITECORE |
| Парткод: | A5C1M92100 |
| Деталь: | I/F Cable /1 |
| Парткод: | A92EN12500 |
| Деталь: | I/F Cable /F |
| Парткод: | A92EN12800 |
| Деталь: | Power source Cable /F |
| Парткод: | A92EN12300 |
| Деталь: | COVER |
| Парткод: | A92E137200 |
| Деталь: | Insulating Part |
| Парткод: | A92E137300 |
| Деталь: | FAX ASSEMBLY |
| Парткод: | A879H01W03 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E137100 |
| Деталь: | Auto Document Feeder |
| Парткод: | A92E270100 |
| Деталь: | UPPER COVER/REAR |
| Парткод: | A92EPP0600 |
| Деталь: | CABLE CLAMP |
| Парткод: | A121PP0200 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | A92EPP0800 |
| Деталь: | TRAY ASSY |
| Парткод: | A92EPP0900 |
| Деталь: | Guide Right |
| Парткод: | A121PP0J00 |
| Деталь: | Guide Left |
| Парткод: | A92EPP1000 |
| Деталь: | PWB Assembly |
| Парткод: | A121PP0700 |
| Деталь: | Separator Pad Assy |
| Парткод: | A92EPP0700 |
| Деталь: | PAD |
| Парткод: | A121PP0D00 |
| Деталь: | HINGE R |
| Парткод: | A121PP0600 |
| Деталь: | HINGE L |
| Парткод: | A121PP0500 |
| Деталь: | Separator Roller Assy |
| Парткод: | A92EPP0400 |
| Деталь: | SOLENOID |
| Парткод: | A121PP0B00 |
| Деталь: | Stopper Left |
| Парткод: | A121PP0H00 |
| Деталь: | Stopper Right |
| Парткод: | A121PP0G00 |
| Деталь: | PHOTO SENSOR |
| Парткод: | A121PP0900 |
| Деталь: | CLUTCH |
| Парткод: | A121PP0A00 |
| Деталь: | PHOTO SENSOR |
| Парткод: | A121PP0800 |
| Деталь: | MOTOR ASSY |
| Парткод: | A92EPP0500 |
| Деталь: | SOLENOID |
| Парткод: | A121PP0C00 |
| Деталь: | SPRING |
| Парткод: | A121PP1000 |
| Деталь: | PHOTO SENSOR |
| Парткод: | A121PP0R00 |
| Деталь: | LABEL CAUTION |
| Парткод: | A92E941200 |
| Деталь: | Stepping motor |
| Парткод: | A63DM10000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D726000 |
| Деталь: | Pulley 18/32T |
| Парткод: | A63D721500 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D725200 |
| Деталь: | STOPPER |
| Парткод: | A63D720600 |
| Деталь: | Release Part |
| Парткод: | A63D721701 |
| Деталь: | Slide Bushing |
| Парткод: | A63D725000 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A63D723900 |
| Деталь: | Conveyance Part |
| Парткод: | A63D722400 |
| Деталь: | LOCK LEVER |
| Парткод: | A63D728100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D722500 |
| Деталь: | Slide Shaft |
| Парткод: | A63D722200 |
| Деталь: | Slide Shaft |
| Парткод: | A63D722100 |
| Деталь: | COLLAR |
| Парткод: | A63D727200 |
| Деталь: | Slide Part |
| Парткод: | A63D722300 |
| Деталь: | PLATE SPRING |
| Парткод: | A63D727302 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D111200 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A63D723600 |
| Деталь: | HOLDER |
| Парткод: | A63D720900 |
| Деталь: | Slide Shaft |
| Парткод: | A63D720200 |
| Деталь: | Timing belt 410L |
| Парткод: | A63D721100 |
| Деталь: | PULLEY |
| Парткод: | A63D721400 |
| Деталь: | Pulley 16T |
| Парткод: | A63D725500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D722000 |
| Деталь: | Pulley 18/32T |
| Парткод: | A63D725300 |
| Деталь: | Timing belt 120L |
| Парткод: | A63D721600 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A63D724500 |
| Деталь: | COVER |
| Парткод: | A63D727100 |
| Деталь: | PRESSING PART |
| Парткод: | A63D720500 |
| Деталь: | REGULATING PLATE |
| Парткод: | A63D720401 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D720700 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D720800 |
| Деталь: | Slide Part |
| Парткод: | A63D720301 |
| Деталь: | COVER |
| Парткод: | A72R162801 |
| Деталь: | COVER MAIN BODY |
| Парткод: | A3GN162701 |
| Деталь: | PLATE NUT |
| Парткод: | 4002504202 |
| Деталь: | Cover /Rear |
| Парткод: | A92E160602 |
| Деталь: | Support Part /Right |
| Парткод: | A3GN160900 |
| Деталь: | Lock Plate spring |
| Парткод: | A3GN621701 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN109300 |
| Деталь: | Cover /Right |
| Парткод: | A92E162301 |
| Деталь: | Cover /Right |
| Парткод: | A3GN162000 |
| Деталь: | HOLDER |
| Парткод: | A3GN133600 |
| Деталь: | HIGH VOLTAGE UNIT |
| Парткод: | A92EM40300 |
| Деталь: | PCB Support |
| Парткод: | V502010044 |
| Деталь: | I/F Flatcable /2 |
| Парткод: | A92EN10C00 |
| Деталь: | Cover /Left |
| Парткод: | A72R163100 |
| Деталь: | Cover /Left |
| Парткод: | A72R163001 |
| Деталь: | MANUAL PAPER FEED ASSY |
| Парткод: | A92ER70600 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD561301 |
| Деталь: | BUSHING |
| Парткод: | 4131300301 |
| Деталь: | GROUND PLATE |
| Парткод: | A92E593100 |
| Деталь: | Paper feed Frame |
| Парткод: | A92E590102 |
| Деталь: | Gear19T |
| Парткод: | A92E590700 |
| Деталь: | GEAR 20T |
| Парткод: | A92E591400 |
| Деталь: | SHAFT |
| Парткод: | A92E590800 |
| Деталь: | SHAFT |
| Парткод: | A92E594600 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | ROLLER |
| Парткод: | 4138303202 |
| Деталь: | Brush Motor |
| Парткод: | A8A1M10100 |
| Деталь: | Gear 21T |
| Парткод: | A92E594400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E592200 |
| Деталь: | Gear 21T |
| Парткод: | A92E594300 |
| Деталь: | Worm Gear 30T |
| Парткод: | A92E592100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E595600 |
| Деталь: | Gear 21/31T |
| Парткод: | A92E594700 |
| Деталь: | Gear 31T |
| Парткод: | A92E594500 |
| Деталь: | GROUND PLATE |
| Парткод: | A92E591200 |
| Деталь: | SHAFT |
| Парткод: | A92E591800 |
| Деталь: | GEAR 22T |
| Парткод: | A92E591100 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD624800 |
| Деталь: | GUIDE |
| Парткод: | A92E590500 |
| Деталь: | GUIDE |
| Парткод: | A0VD561502 |
| Деталь: | HOLDER |
| Парткод: | A92E621000 |
| Деталь: | ROLLER ASSY |
| Парткод: | A92EV62001 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD560601 |
| Деталь: | GEAR 22T |
| Парткод: | A92E590900 |
| Деталь: | SHAFT |
| Парткод: | A92E595401 |
| Деталь: | GUIDE |
| Парткод: | A0VD561800 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4131305601 |
| Деталь: | SHAFT |
| Парткод: | A92E595301 |
| Деталь: | GEAR 22T |
| Парткод: | A92E591000 |
| Деталь: | ACTUATOR |
| Парткод: | A0VD560300 |
| Деталь: | Label MPT |
| Парткод: | A92E940301 |
| Деталь: | Conveyance Wiring /2 |
| Парткод: | A92EN10F00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E591700 |
| Деталь: | PAPER FEED DRIVE ASSY |
| Парткод: | A92ER70100 |
| Деталь: | Guide Sheet |
| Парткод: | A3GN217000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD233102 |
| Деталь: | Gear 38/65T |
| Парткод: | A0VD230400 |
| Деталь: | BUSHING |
| Парткод: | 4036473001 |
| Деталь: | PIN |
| Парткод: | 4036301401 |
| Деталь: | GEAR 36T |
| Парткод: | A0VD231101 |
| Деталь: | SHAFT |
| Парткод: | A0VD230800 |
| Деталь: | BUSHING |
| Парткод: | A0VD702400 |
| Деталь: | Gear 23/55T |
| Парткод: | A0VD230301 |
| Деталь: | Gear22T |
| Парткод: | A0VD231200 |
| Деталь: | GEAR 25T |
| Парткод: | A0VD230901 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD233301 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | LEVER |
| Парткод: | A0VD624100 |
| Деталь: | Connecting Claw |
| Парткод: | A92E693000 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4138259701 |
| Деталь: | Sensor Relay harness |
| Парткод: | A92EN10B00 |
| Деталь: | SHAFT |
| Парткод: | A0VD230501 |
| Деталь: | CLUTCH |
| Парткод: | A02EM20000 |
| Деталь: | BUSHING |
| Парткод: | 4134588202 |
| Деталь: | SHAFT |
| Парткод: | A0VD230101 |
| Деталь: | CUSHION |
| Парткод: | A63D704400 |
| Деталь: | Processing Tray |
| Парткод: | A63D730013 |
| Деталь: | Processing Tray |
| Парткод: | A63D730103 |
| Деталь: | CUSHION |
| Парткод: | A63D704500 |
| Деталь: | Connecting Arm |
| Парткод: | A63D727700 |
| Деталь: | Hold Part |
| Парткод: | A63D724000 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D726200 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D727900 |
| Деталь: | Hold Part |
| Парткод: | A63D727400 |
| Деталь: | ARM |
| Парткод: | A63D727600 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D727800 |
| Деталь: | Hold Part |
| Парткод: | A63D727500 |
| Деталь: | Connecting Arm |
| Парткод: | A63D735100 |
| Деталь: | Holding Lever |
| Парткод: | A63D734900 |
| Деталь: | REGULATING PLATE |
| Парткод: | A63D730402 |
| Деталь: | SHAFT |
| Парткод: | A63D734300 |
| Деталь: | BUSHING |
| Парткод: | A63D735800 |
| Деталь: | SHEET |
| Парткод: | A63D739400 |
| Деталь: | Holding Cam |
| Парткод: | A63D735000 |
| Деталь: | HOLDER |
| Парткод: | A63D734800 |
| Деталь: | HOLDER |
| Парткод: | A63D730500 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D736200 |
| Деталь: | GUIDE |
| Парткод: | A63D737400 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | ROLL |
| Парткод: | A63D735500 |
| Деталь: | LOCK CLAW |
| Парткод: | A63D735301 |
| Деталь: | LOCK CLAW |
| Парткод: | A63D735401 |
| Деталь: | GUIDE |
| Парткод: | A63D701301 |
| Деталь: | Slide Shaft |
| Парткод: | A63D730600 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D702600 |
| Деталь: | Guide Shaft |
| Парткод: | A63D702800 |
| Деталь: | LOCK CLAW |
| Парткод: | A63D702200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D700700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A63D702700 |
| Деталь: | BUSHING |
| Парткод: | A63D705100 |
| Деталь: | SHAFT |
| Парткод: | A63D701400 |
| Деталь: | GUIDE |
| Парткод: | A63D700600 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D735700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD164000 |
| Деталь: | COVER |
| Парткод: | A3GN812400 |
| Деталь: | SHAFT |
| Парткод: | A0VD162101 |
| Деталь: | Lever /Rear |
| Парткод: | A0VD163400 |
| Деталь: | Connecting Part |
| Парткод: | A92E813401 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A92E813900 |
| Деталь: | HOLDER |
| Парткод: | A0VD161100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD163500 |
| Деталь: | Lock Claw /Front |
| Парткод: | A92E813600 |
| Деталь: | Wiring Cover |
| Парткод: | A0VD162400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD163200 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | GROUND PLATE |
| Парткод: | A3GN702811 |
| Деталь: | Conveyance ASSY |
| Парткод: | A92ER70700 |
| Деталь: | FIXED LEAD RESISTORS |
| Парткод: | V800400032 |
| Деталь: | HOLDER |
| Парткод: | A92E703300 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD703700 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0VD702700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD701301 |
| Деталь: | Neutralizing Part |
| Парткод: | A3GN701800 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD700302 |
| Деталь: | ACTUATOR |
| Парткод: | A0VD700202 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A3GN700500 |
| Деталь: | CONTACT |
| Парткод: | A3GN701100 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A3GN708101 |
| Деталь: | HOLDER |
| Парткод: | A3GN700100 |
| Деталь: | 2nd Transfer Roller Unit |
| Парткод: | A4Y5WY3 |
| Деталь: | DUCT |
| Парткод: | A92E813200 |
| Деталь: | COVER |
| Парткод: | A92E816000 |
| Деталь: | SEAL |
| Парткод: | A92E816700 |
| Деталь: | SEAL |
| Парткод: | A92E816800 |
| Деталь: | HOLDER |
| Парткод: | A92E816300 |
| Деталь: | Release Lever |
| Парткод: | A92E813501 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | CONNECTOR |
| Парткод: | V651010002 |
| Деталь: | FILTER |
| Парткод: | A92E816600 |
| Деталь: | COVER |
| Парткод: | A92E812500 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A3GN700700 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A3GN700800 |
| Деталь: | LABEL |
| Парткод: | A161940602 |
| Деталь: | LABEL |
| Парткод: | A0HF952400 |
| Деталь: | OPTICAL UNIT |
| Парткод: | A92E260100 |
| Деталь: | Scanner Belt |
| Парткод: | A121PP0N02 |
| Деталь: | Flat Cable 18P |
| Парткод: | A121PP0Q00 |
| Деталь: | Flat Cable 31P |
| Парткод: | A92EPP0200 |
| Деталь: | IR Cover Assy |
| Парткод: | A92EPP0100 |
| Деталь: | Flat Cable 24P |
| Парткод: | A92EPP0300 |
| Деталь: | LABEL CAUTION |
| Парткод: | A92E941100 |
| Деталь: | Holding Lever |
| Парткод: | A72R890300 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A72R892500 |
| Деталь: | Label JAM |
| Парткод: | A0VD949100 |
| Деталь: | Label Hi-Temp Caution/Jam |
| Парткод: | A3GN948300 |
| Деталь: | GUIDE |
| Парткод: | A121902500 |
| Деталь: | LEVER |
| Парткод: | A121893002 |
| Деталь: | FUSING UNIT 230V |
| Парткод: | A4Y5W22 |
| Деталь: | ACTUATOR |
| Парткод: | A6DR892300 |
| Деталь: | GUIDE |
| Парткод: | A3GN892102 |
| Деталь: | Paper exit Guide /Front |
| Парткод: | A3GN893700 |
| Деталь: | BUSHING |
| Парткод: | A0P0364000 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Ground Contact |
| Парткод: | A72R892700 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD892400 |
| Деталь: | SEAL |
| Парткод: | A3GN146300 |
| Деталь: | Fixing Relay harness |
| Парткод: | A92EN10300 |
| Деталь: | Paper exit Guide /Rear |
| Парткод: | A3GN893600 |
| Деталь: | Holding Plate /Front |
| Парткод: | A72R890400 |
| Деталь: | ROLL |
| Парткод: | A72R890700 |
| Деталь: | Holding Weight |
| Парткод: | A72R890600 |
| Деталь: | ROLL |
| Парткод: | A72R890800 |
| Деталь: | ROLL |
| Парткод: | A72R890900 |
| Деталь: | Holding Plate /Rear |
| Парткод: | A72R890500 |
| Деталь: | Paper exit Holder /K |
| Парткод: | A72R892001 |
| Деталь: | Gear 38/40T |
| Парткод: | A0VD890800 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | A72R890100 |
| Деталь: | Paper exit Roll |
| Парткод: | A72R891300 |
| Деталь: | SHAFT |
| Парткод: | A72R895500 |
| Деталь: | ACTUATOR |
| Парткод: | A72R890201 |
| Деталь: | Paper exit Holder |
| Парткод: | A72R895300 |
| Деталь: | SPRING |
| Парткод: | A72R891200 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A72R895100 |
| Деталь: | Paper exit Holder /HK |
| Парткод: | A72R892100 |
| Деталь: | Paper exit Guide /Middle |
| Парткод: | A3GN893500 |
| Деталь: | REGULATING PLATE |
| Парткод: | A92E626400 |
| Деталь: | CUSHION |
| Парткод: | A92E625400 |
| Деталь: | CUSHION |
| Парткод: | A92E685300 |
| Деталь: | Auxiliary Guide |
| Парткод: | A92E685100 |
| Деталь: | Auxiliary Guide |
| Парткод: | A92E625200 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A795622700 |
| Деталь: | LABEL |
| Парткод: | A161943000 |
| Деталь: | LOCK CLAW |
| Парткод: | A92E626500 |
| Деталь: | LEVER |
| Парткод: | A92E626601 |
| Деталь: | COVER |
| Парткод: | A92E626700 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH621000 |
| Деталь: | REGULATING PLATE |
| Парткод: | A92E626301 |
| Деталь: | GEAR 14T |
| Парткод: | 4658301201 |
| Деталь: | RACK |
| Парткод: | A92E626101 |
| Деталь: | CUSHION |
| Парткод: | A92E624300 |
| Деталь: | LABEL |
| Парткод: | A3GN940500 |
| Деталь: | Paper feed Cover /Upper |
| Парткод: | A3GN628201 |
| Деталь: | LABEL |
| Парткод: | A3GN940201 |
| Деталь: | Paper feed Cover /Front |
| Парткод: | A3GN628100 |
| Деталь: | Label Paper supply |
| Парткод: | A92E940100 |
| Деталь: | Adjusting Plate |
| Парткод: | A92E627100 |
| Деталь: | Adjusting Plate |
| Парткод: | A92E629200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E621400 |
| Деталь: | Label FD metric |
| Парткод: | A92E940401 |
| Деталь: | Label FD inch A |
| Парткод: | A92E940501 |
| Деталь: | HOLDER |
| Парткод: | A92E627901 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A92E627801 |
| Деталь: | Holding Plate |
| Парткод: | A92E627600 |
| Деталь: | RACK |
| Парткод: | A92E626200 |
| Деталь: | Ground Plate spring /A |
| Парткод: | A3GN621200 |
| Деталь: | FIXED LEAD RESISTORS |
| Парткод: | V800400032 |
| Деталь: | Ground Plate spring /B |
| Парткод: | A3GN621300 |
| Деталь: | Label FD inch B |
| Парткод: | A92E940601 |
| Деталь: | SHEET |
| Парткод: | A92E627701 |
| Деталь: | HOLDER |
| Парткод: | A92E627500 |
| Деталь: | LEVER |
| Парткод: | A92E627300 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A92E629301 |
| Деталь: | LABEL |
| Парткод: | A02E940300 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A92E628801 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A92E628701 |
| Деталь: | LEVER |
| Парткод: | A92E628400 |
| Деталь: | COVER |
| Парткод: | A92E628600 |
| Деталь: | LEVER |
| Парткод: | A92E628300 |
| Деталь: | LEVER |
| Парткод: | A92E627401 |
| Деталь: | LEVER |
| Парткод: | A92E628000 |
| Деталь: | REGULATING PLATE |
| Парткод: | A92E627202 |
| Деталь: | Label CD scale |
| Парткод: | A92E940201 |
| Деталь: | Cover /Upper |
| Парткод: | A92G160400 |
| Деталь: | HOLD PLATE |
| Парткод: | A3GN162500 |
| Деталь: | SEAL |
| Парткод: | A3GN162900 |
| Деталь: | SEAL |
| Парткод: | A3GN163000 |
| Деталь: | Label ineo+3851FS |
| Парткод: | A92G942100 |
| Деталь: | Support Part |
| Парткод: | A3GN160801 |
| Деталь: | Open/close Stopper |
| Парткод: | A3GN812300 |
| Деталь: | Plate /D |
| Парткод: | A0Y5944800 |
| Деталь: | Cover /Front |
| Парткод: | A3GN160200 |
| Деталь: | Cover /Front |
| Парткод: | A3GN180101 |
| Деталь: | Cleaning Part |
| Парткод: | A3GN162600 |
| Деталь: | BAND |
| Парткод: | A0ED162401 |
| Деталь: | Cover /Left |
| Парткод: | A92E160300 |
| Деталь: | LABEL CAUTION |
| Парткод: | A7PU941701 |
| Деталь: | GUIDE |
| Парткод: | A3GN707700 |
| Деталь: | GUIDE |
| Парткод: | A3GN707600 |
| Деталь: | HOLDER |
| Парткод: | A92E707500 |
| Деталь: | ACTUATOR |
| Парткод: | A92E707100 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD707201 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A0P0M50400 |
| Деталь: | GUIDE |
| Парткод: | A92E707302 |
| Деталь: | Transfer Relay harness |
| Парткод: | A92EN10J00 |
| Деталь: | PROTECTION PART |
| Парткод: | A3GN708000 |
| Деталь: | PAPERFEED SOLENOID |
| Парткод: | A034M20000 |
| Деталь: | LEVER |
| Парткод: | A3GN706600 |
| Деталь: | COVER |
| Парткод: | A3GN112300 |
| Деталь: | Neutralizing LED array |
| Парткод: | A3GNM30400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN111500 |
| Деталь: | HOLDER |
| Парткод: | A3GN706500 |
| Деталь: | COVER |
| Парткод: | A3GN706100 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A034213400 |
| Деталь: | CONTACT |
| Парткод: | A92E706300 |
| Деталь: | Photo sensing |
| Парткод: | A161M50300 |
| Деталь: | GUIDE |
| Парткод: | A92E706400 |
| Деталь: | SEAL |
| Парткод: | A92E708500 |
| Деталь: | GUIDE |
| Парткод: | A92E707800 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A92E707900 |
| Деталь: | Reinforce Plate /Upper |
| Парткод: | A92G109500 |
| Деталь: | HOLDER |
| Парткод: | A92E133500 |
| Деталь: | Reinforce Frame |
| Парткод: | A72R109802 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | HOLDER |
| Парткод: | A3GN135300 |
| Деталь: | Adjusting Spring |
| Парткод: | A0VD135201 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A3GN135200 |
| Деталь: | SPACER |
| Парткод: | A3GN135100 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06M60100 |
| Деталь: | Interlock Wiring |
| Парткод: | A3GNN10D00 |
| Деталь: | Seal /Left |
| Парткод: | A3GN146400 |
| Деталь: | Hold Holder |
| Парткод: | A0VD136100 |
| Деталь: | Connecting Seal /Rear |
| Парткод: | A3GN144100 |
| Деталь: | Connecting Seal |
| Парткод: | A3GN144500 |
| Деталь: | COVER |
| Парткод: | A3GN145700 |
| Деталь: | Holding Seal |
| Парткод: | A92E144600 |
| Деталь: | Filter Holder |
| Парткод: | A92E144402 |
| Деталь: | FERRITECORE |
| Парткод: | A5C1M92100 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | Supply Duct /Left rear |
| Парткод: | A92E142100 |
| Деталь: | Protection Seal |
| Парткод: | A72R101200 |
| Деталь: | SHEET |
| Парткод: | A92E142501 |
| Деталь: | Wiring Guide |
| Парткод: | A63D901500 |
| Деталь: | CUSHION |
| Парткод: | A63D704400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D892000 |
| Деталь: | FLANGE |
| Парткод: | A63D892300 |
| Деталь: | Timing belt 72L |
| Парткод: | A63D892400 |
| Деталь: | Pulley 14T |
| Парткод: | A63D891200 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A63D892500 |
| Деталь: | SPACER |
| Парткод: | A63D893300 |
| Деталь: | GEAR 30T |
| Парткод: | A63D891300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D892100 |
| Деталь: | COVER |
| Парткод: | A63D893100 |
| Деталь: | Brush Motor |
| Парткод: | A63DH00503 |
| Деталь: | SHAFT |
| Парткод: | A63D891700 |
| Деталь: | Rotation Holder |
| Парткод: | A63D891100 |
| Деталь: | Photoreflector |
| Парткод: | A108M50000 |
| Деталь: | TRAY |
| Парткод: | A63D900300 |
| Деталь: | TRAY |
| Парткод: | A63D900100 |
| Деталь: | TRAY |
| Парткод: | A63D901001 |
| Деталь: | FNS Relay harness |
| Парткод: | A63DN11601 |
| Деталь: | Positioning Shaft |
| Парткод: | A63D901100 |
| Деталь: | Bushing /A |
| Парткод: | A1RF846400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D892201 |
| Деталь: | Holding Part |
| Парткод: | A63D890101 |
| Деталь: | Wiring Guide |
| Парткод: | A63D900200 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Protection Sheet |
| Парткод: | A63D901700 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D892712 |
| Деталь: | TRAY |
| Парткод: | A63D900012 |
| Деталь: | ROLL |
| Парткод: | A63D901300 |
| Деталь: | ROLL |
| Парткод: | A63D901200 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | FERRITE CORE |
| Парткод: | A3GNM93100 |
| Деталь: | FERRITE CORE |
| Парткод: | A3GNM93200 |
| Деталь: | HOLD PLATE |
| Парткод: | A3GN145800 |
| Деталь: | Hold Duct /Left rear |
| Парткод: | A72R142202 |
| Деталь: | Protection Seal |
| Парткод: | A92E133400 |
| Деталь: | FERRITE CORE |
| Парткод: | A3GNM71C00 |
| Деталь: | SEAL |
| Парткод: | A92E134400 |
| Деталь: | GUIDE |
| Парткод: | A92E133700 |
| Деталь: | SEAL |
| Парткод: | A92E134300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E133000 |
| Деталь: | GUIDE |
| Парткод: | A92E132800 |
| Деталь: | PROTECTION |
| Парткод: | 1154467001 |
| Деталь: | GUIDE |
| Парткод: | A92E133801 |
| Деталь: | PIN |
| Парткод: | 4036254901 |
| Деталь: | AC Wiring /2 |
| Парткод: | A92EN10900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E132200 |
| Деталь: | Mounting Rail |
| Парткод: | A92E134200 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996305501 |
| Деталь: | ROCKER SWITCH |
| Парткод: | A034M60200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E134700 |
| Деталь: | AC Wiring /1 |
| Парткод: | A92EN10800 |
| Деталь: | HDD |
| Парткод: | A2X0M72C00 |
| Деталь: | SPACER |
| Парткод: | A5C1134111 |
| Деталь: | Power source Cable /H |
| Парткод: | A92EN12A00 |
| Деталь: | I/F Cable /S |
| Парткод: | A92EN12900 |
| Деталь: | SHIELD PLATE |
| Парткод: | A92E132600 |
| Деталь: | SHIELD PLATE |
| Парткод: | A92E132900 |
| Деталь: | Support Rubber |
| Парткод: | A4EU138000 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A5C1134200 |
| Деталь: | Insulating Part /1 |
| Парткод: | A92E135300 |
| Деталь: | Lock Plate spring |
| Парткод: | A3GN621701 |
| Деталь: | SHIELD PLATE |
| Парткод: | A92E134500 |
| Деталь: | SEAL |
| Парткод: | A3GN132900 |
| Деталь: | Protection Sheet |
| Парткод: | A92E136400 |
| Деталь: | Insulating Part /2 |
| Парткод: | A92E135400 |
| Деталь: | Label Toner |
| Парткод: | A92E401200 |
| Деталь: | Cover /Left front |
| Парткод: | A92E138100 |
| Деталь: | GUIDE |
| Парткод: | A92E133300 |
| Деталь: | SPEAKER |
| Парткод: | A0P0M73100 |
| Деталь: | GUIDE |
| Парткод: | A72R133000 |
| Деталь: | LIFTING PLATE |
| Парткод: | A92E624100 |
| Деталь: | FRICTION SHEET |
| Парткод: | 0978381101 |
| Деталь: | LEVER |
| Парткод: | A92E633600 |
| Деталь: | LEVER |
| Парткод: | A92E633700 |
| Деталь: | LIFTING PLATE |
| Парткод: | A92E624500 |
| Деталь: | SHAFT |
| Парткод: | A92E624600 |
| Деталь: | BUSHING |
| Парткод: | 4138324401 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD624800 |
| Деталь: | CLUTCH |
| Парткод: | 4030303401 |
| Деталь: | ROLLER |
| Парткод: | 4138303202 |
| Деталь: | HOLDER |
| Парткод: | A92E621800 |
| Деталь: | ROLLER ASSY |
| Парткод: | A92EV62001 |
| Деталь: | HOLDER |
| Парткод: | A92E621000 |
| Деталь: | WASHER |
| Парткод: | A00J192900 |
| Деталь: | LEVER |
| Парткод: | A92E632301 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A92E632602 |
| Деталь: | Pulling Coil spring /B |
| Парткод: | A92E632702 |
| Деталь: | SHAFT |
| Парткод: | A92E632200 |
| Деталь: | LEVER |
| Парткод: | A92E632500 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A92E633201 |
| Деталь: | Lever /B |
| Парткод: | A92E632800 |
| Деталь: | COVER |
| Парткод: | A92E632900 |
| Деталь: | PRESSING PART |
| Парткод: | A92E631900 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A92E632101 |
| Деталь: | LEVER |
| Парткод: | A92E631702 |
| Деталь: | COVER |
| Парткод: | A92E633001 |
| Деталь: | SHAFT |
| Парткод: | A92E631000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E631100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4036576501 |
| Деталь: | SHAFT |
| Парткод: | A92E633100 |
| Деталь: | LEVER |
| Парткод: | A92E631400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E631200 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | GUIDE |
| Парткод: | A92E631501 |
| Деталь: | LEVER |
| Парткод: | A92E628201 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A92E629001 |
| Деталь: | GUIDE |
| Парткод: | A3GN623100 |
| Деталь: | GUIDE |
| Парткод: | 4131305702 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4131305601 |
| Деталь: | Paper feed Cassette |
| Парткод: | A92E621102 |
| Деталь: | CASSETTE ASSY |
| Парткод: | A92ER70400 |
| Деталь: | Stepping motor |
| Парткод: | A5C1M10400 |
| Деталь: | HOLDER |
| Парткод: | A3GN400100 |
| Деталь: | GEAR 25T |
| Парткод: | A3GN400400 |
| Деталь: | Gear 49/86T |
| Парткод: | A3GN400300 |
| Деталь: | Gear 20/107T |
| Парткод: | A3GN400200 |
| Деталь: | GEAR 30T |
| Парткод: | A02E240600 |
| Деталь: | SPRING |
| Парткод: | 4038541101 |
| Деталь: | GUIDE |
| Парткод: | A3GN400800 |
| Деталь: | SPRING |
| Парткод: | A3GN401100 |
| Деталь: | WASHER |
| Парткод: | 4131412801 |
| Деталь: | TB Drive Frame ASSY |
| Парткод: | A92GR70000 |
| Деталь: | HOLDER |
| Парткод: | A92E402700 |
| Деталь: | LABEL |
| Парткод: | A2X0949100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN400900 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A3GN401000 |
| Деталь: | Relay Connector |
| Парткод: | A0EDM60001 |
| Деталь: | Toner Detection harness |
| Парткод: | A92EN10500 |
| Деталь: | LABEL K |
| Парткод: | A3GN401600 |
| Деталь: | LABEL C |
| Парткод: | A3GN401500 |
| Деталь: | LABEL M |
| Парткод: | A3GN401400 |
| Деталь: | LABEL Y |
| Парткод: | A3GN401300 |
| Деталь: | Relay Wiring |
| Парткод: | A3GNN10U00 |
| Деталь: | GUIDE |
| Парткод: | A3GN137100 |
| Деталь: | Toner Drive harness |
| Парткод: | A92EN10600 |
| Деталь: | Protection Plate |
| Парткод: | A72R101100 |
| Деталь: | Protection Sheet |
| Парткод: | A72R101300 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | A6X0R70122 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996305501 |
| Деталь: | GUIDE |
| Парткод: | A3GN102500 |
| Деталь: | STOPPER |
| Парткод: | A3GN621600 |
| Деталь: | Gear 16/26T |
| Парткод: | A0VD235600 |
| Деталь: | Gear16T |
| Парткод: | A0VD235400 |
| Деталь: | GEAR 16/16T |
| Парткод: | A0VD235500 |
| Деталь: | Gear 22/30T |
| Парткод: | A0VD235900 |
| Деталь: | Holding Plate |
| Парткод: | A3GN235200 |
| Деталь: | Waste Toner Bottle |
| Парткод: | A4Y5WY1 |
| Деталь: | Drive Holder |
| Парткод: | A3GN235113 |
| Деталь: | HOLDER |
| Парткод: | A3GN106700 |
| Деталь: | COVER |
| Парткод: | A3GN107100 |
| Деталь: | LEVER |
| Парткод: | A3GN362601 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD362702 |
| Деталь: | Gear16T |
| Парткод: | A0VD235700 |
| Деталь: | Regulating Sheet |
| Парткод: | A3GN102300 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140051 |
| Деталь: | SEAL |
| Парткод: | A3GN102200 |
| Деталь: | Pulley 16T |
| Парткод: | A63D725500 |
| Деталь: | Idler |
| Парткод: | A63D731101 |
| Деталь: | Pulley 18/24T |
| Парткод: | A63D730800 |
| Деталь: | Timing belt 82L |
| Парткод: | A63D732700 |
| Деталь: | Adjusting Plate |
| Парткод: | A63D732900 |
| Деталь: | Timing belt 586L |
| Парткод: | A63D730700 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140071 |
| Деталь: | HOLDER |
| Парткод: | A63D736801 |
| Деталь: | REGULATING PLATE |
| Парткод: | A63D732101 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A63D733400 |
| Деталь: | Guide Shaft |
| Парткод: | A63D736900 |
| Деталь: | Guide Shaft |
| Парткод: | A63D737700 |
| Деталь: | CUSHION |
| Парткод: | A63D704500 |
| Деталь: | Fixing Guide |
| Парткод: | A63D732201 |
| Деталь: | CONNECTOR |
| Парткод: | V651010003 |
| Деталь: | Slide Part |
| Парткод: | A63D738800 |
| Деталь: | Up/down Guide /Rear |
| Парткод: | A63D734000 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A63D739100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A63D739200 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D733201 |
| Деталь: | Up/down Arm |
| Парткод: | A63D733900 |
| Деталь: | Slide Shaft |
| Парткод: | A63D736700 |
| Деталь: | Release Arm |
| Парткод: | A63D738900 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A63D739000 |
| Деталь: | Pressing Plate spring |
| Парткод: | A63D734100 |
| Деталь: | Up/down Shaft |
| Парткод: | A63D731400 |
| Деталь: | Fixing Part /6 |
| Парткод: | A0H0911500 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Support Shaft /Rear |
| Парткод: | A63D732600 |
| Деталь: | BUSHING |
| Парткод: | 4134588202 |
| Деталь: | GEAR 17/32T |
| Парткод: | A63D738000 |
| Деталь: | GEAR 17/30T |
| Парткод: | A63D738100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D731501 |
| Деталь: | Stepping motor |
| Парткод: | A63DM10100 |
| Деталь: | BALL BEARING |
| Парткод: | A00J617800 |
| Деталь: | Gear 17/37T |
| Парткод: | A63D737900 |
| Деталь: | Gear 20/27T |
| Парткод: | A63D738200 |
| Деталь: | GEAR 24T |
| Парткод: | A63D738300 |
| Деталь: | Stepping motor |
| Парткод: | A63DM10000 |
| Деталь: | HOLD PLATE |
| Парткод: | A63D737601 |
| Деталь: | BASE FRAME |
| Парткод: | A63D734402 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A63D733100 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A63D739300 |
| Деталь: | COVER |
| Парткод: | A92E161200 |
| Деталь: | Drive Relay harness |
| Парткод: | A92EN10400 |
| Деталь: | FERRITE CORE |
| Парткод: | A3GNM71C00 |
| Деталь: | COVER |
| Парткод: | A3GN161701 |
| Деталь: | Operation Panel Mounting Plate ASSY |
| Парткод: | A92ER70500 |
| Деталь: | COVER |
| Парткод: | A92E161100 |
| Деталь: | COVER |
| Парткод: | A92E161401 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E190700 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A92EM71202 |
| Деталь: | PWB Assembly (MCMB) |
| Парткод: | A3GNH00500 |
| Деталь: | COVER |
| Парткод: | A92E161300 |
| Деталь: | SEAL |
| Парткод: | A7PU168600 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | HOLDER |
| Парткод: | A3GN135400 |
| Деталь: | LEVER |
| Парткод: | A3GN135500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN190101 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E191600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN190600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN190801 |
| Деталь: | Light blocking Sheet |
| Парткод: | A3GN191300 |
| Деталь: | LENS |
| Парткод: | A3GN161800 |
| Деталь: | SEAL |
| Парткод: | A92E161500 |
| Деталь: | COVER |
| Парткод: | A72R161000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN190511 |
| Деталь: | I/F Cable /2 |
| Парткод: | A92EN12600 |
| Деталь: | I/F Cable /P |
| Парткод: | A92EN12B00 |
| Деталь: | STOPPER |
| Парткод: | A3GN191500 |
| Деталь: | I/F Cable /B |
| Парткод: | A92EN12400 |
| Деталь: | Wiring Part |
| Парткод: | A72R130500 |
| Деталь: | GUIDE |
| Парткод: | A63D700400 |
| Деталь: | PWB Assembly |
| Парткод: | A63DH00A00 |
| Деталь: | Exposure Cover |
| Парткод: | A63D705900 |
| Деталь: | GUIDE |
| Парткод: | A63D704602 |
| Деталь: | STOPPER RING |
| Парткод: | 1033440203 |
| Деталь: | SCREW |
| Парткод: | A0WG337701 |
| Деталь: | Regulating Guide |
| Парткод: | A63D705700 |
| Деталь: | ROLL |
| Парткод: | A63D901300 |
| Деталь: | GUIDE |
| Парткод: | A63D704700 |
| Деталь: | Guide Sheet |
| Парткод: | A63D705800 |
| Деталь: | CUSHION |
| Парткод: | A63D704400 |
| Деталь: | POSITIONING PLATE |
| Парткод: | A72R100300 |
| Деталь: | FNS Relay harness |
| Парткод: | A72RN10300 |
| Деталь: | FNS Relay harness |
| Парткод: | A92GN10200 |
| Деталь: | Power supply Relay harness |
| Парткод: | A92GN10100 |
| Деталь: | Manual Bypass ASSY |
| Парткод: | A92ER70300 |
| Деталь: | REGULATING PLATE |
| Парткод: | A92E591900 |
| Деталь: | LEVER |
| Парткод: | A92E590601 |
| Деталь: | REGULATING PLATE |
| Парткод: | A92E592000 |
| Деталь: | LIFTING PLATE |
| Парткод: | A92E590302 |
| Деталь: | LABEL |
| Парткод: | A3GN940500 |
| Деталь: | TRAY |
| Парткод: | A92E591600 |
| Деталь: | Bypass Tray |
| Парткод: | A92E590203 |
| Деталь: | FRAME |
| Парткод: | A92E590403 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A92E592501 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A92E593000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A92E592400 |
| Деталь: | GEAR 14T |
| Парткод: | 4131302702 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4138325501 |
| Деталь: | COLLAR |
| Парткод: | 4120301901 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN112900 |
| Деталь: | Drawer CN |
| Парткод: | V651020005 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A3GN112800 |
| Деталь: | HOLDER |
| Парткод: | A3GN113000 |
| Деталь: | Rail /Lower |
| Парткод: | A3GN111001 |
| Деталь: | Rail /Upper |
| Парткод: | A3GN111300 |
| Деталь: | Rail /Lower |
| Парткод: | A3GN111200 |
| Деталь: | COVER |
| Парткод: | A3GN112400 |
| Деталь: | SEAL |
| Парткод: | A3GN113200 |
| Деталь: | SEAL |
| Парткод: | A3GN113100 |
| Деталь: | Rail /Lower |
| Парткод: | A3GN111101 |
| Деталь: | Neutralizing LED array |
| Парткод: | A3GNM30400 |
| Деталь: | Rail /Upper |
| Парткод: | A3GN111400 |
| Деталь: | Scatteringprevention Sheet |
| Парткод: | A92E111500 |
| Деталь: | Connecting Seal /Middle |
| Парткод: | A3GN144200 |
| Деталь: | SEALING PART |
| Парткод: | A3GN140600 |
| Деталь: | Supply Duct /Rear |
| Парткод: | A3GN148200 |
| Деталь: | Sealing Part Outside |
| Парткод: | A3GN149600 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148700 |
| Деталь: | Supply Duct /Rear |
| Парткод: | A3GN148100 |
| Деталь: | Supply Duct /Rear |
| Парткод: | A3GN148001 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148300 |
| Деталь: | SEALING PART |
| Парткод: | A3GN141201 |
| Деталь: | Supply Duct /Rear |
| Парткод: | A3GN140100 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145100 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145200 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145600 |
| Деталь: | Sealing Part /Middle |
| Парткод: | A3GN140700 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145400 |
| Деталь: | Sealing Part /Lower |
| Парткод: | A3GN149100 |
| Деталь: | Sealing Part /Lower |
| Парткод: | A3GN149200 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145300 |
| Деталь: | Supply Duct /Lower |
| Парткод: | A3GN140300 |
| Деталь: | SEALING PART |
| Парткод: | A3GN141100 |
| Деталь: | SEALING PART |
| Парткод: | A3GN141300 |
| Деталь: | SEALING PART |
| Парткод: | A3GN140800 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148500 |
| Деталь: | Sealing Part Outside |
| Парткод: | A3GN149300 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148800 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148900 |
| Деталь: | Sealing Part Outside |
| Парткод: | A3GN149500 |
| Деталь: | Mounting Duct /Rear |
| Парткод: | A3GN147201 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | Sealing Part /Lower |
| Парткод: | A3GN149000 |
| Деталь: | SEAL |
| Парткод: | A3GN147600 |
| Деталь: | GUIDE |
| Парткод: | A3GN147000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D725100 |
| Деталь: | Slide Shaft |
| Парткод: | A63D723000 |
| Деталь: | Regulating Plate /Front |
| Парткод: | A63D723201 |
| Деталь: | Reinforce Plate /Front |
| Парткод: | A63D726801 |
| Деталь: | PULLEY |
| Парткод: | A63D721400 |
| Деталь: | Timing belt 120L |
| Парткод: | A63D721600 |
| Деталь: | Pulley 18/24T |
| Парткод: | A63D723400 |
| Деталь: | Timing belt 272L |
| Парткод: | A63D723300 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A63D724500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D725900 |
| Деталь: | Stepping motor |
| Парткод: | A63DM10000 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A63D723600 |
| Деталь: | Slide Part |
| Парткод: | A63D723100 |
| Деталь: | HOLDER |
| Парткод: | A63D723700 |
| Деталь: | FLANGE |
| Парткод: | A0HR213600 |
| Деталь: | Pulley 16T |
| Парткод: | A63D721200 |
| Деталь: | Timing belt 196L |
| Парткод: | A63D726500 |
| Деталь: | ROLL |
| Парткод: | A63D901300 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A63D724400 |
| Деталь: | STOPPER |
| Парткод: | A63D724301 |
| Деталь: | SHAFT |
| Парткод: | A63D726100 |
| Деталь: | Pulley 16T |
| Парткод: | A63D725500 |
| Деталь: | COVER |
| Парткод: | A63D111700 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Support Spacer |
| Парткод: | V502010064 |
| Деталь: | Wiring Guide |
| Парткод: | A63D130200 |
| Деталь: | FNS Wiring |
| Парткод: | A63DN11500 |
| Деталь: | PWB Assembly (FSCB) |
| Парткод: | A63DH00103 |
| Деталь: | FNS Wiring |
| Парткод: | A63DN11400 |
| Деталь: | FNS Wiring |
| Парткод: | A63DN11800 |
| Деталь: | FNS Wiring |
| Парткод: | A63DN11001 |
| Деталь: | CONNECTOR |
| Парткод: | V651010002 |
| Деталь: | COVER |
| Парткод: | A63D131001 |
| Деталь: | FNS Relay harness |
| Парткод: | A63DN11101 |
| Деталь: | FNS Wiring |
| Парткод: | A63DN11300 |
| Деталь: | CONNECTOR |
| Парткод: | V651010009 |
| Деталь: | FNS Relay harness |
| Парткод: | A63DN12000 |
| Деталь: | Timing belt 386L |
| Парткод: | A63D722700 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A63D742200 |
| Деталь: | CUSHION |
| Парткод: | A63D704500 |
| Деталь: | Stapler Cover |
| Парткод: | A63D741601 |
| Деталь: | Sheet /3 |
| Парткод: | A63D171700 |
| Деталь: | Stapler Cover /Lower ASSY |
| Парткод: | A63DR70000 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A63D742000 |
| Деталь: | ACTUATOR |
| Парткод: | A63D170501 |
| Деталь: | SWITCH |
| Парткод: | 56UA85010 |
| Деталь: | Cover /Left |
| Парткод: | A63D170002 |
| Деталь: | ROLL |
| Парткод: | A63D171200 |
| Деталь: | Hold Arm |
| Парткод: | A63D171100 |
| Деталь: | Auxiliary Tray |
| Парткод: | A63D171001 |
| Деталь: | Support Shaft |
| Парткод: | A63D740900 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A63D741401 |
| Деталь: | PLATE SPRING |
| Парткод: | A63D741700 |
| Деталь: | Stapler Cover |
| Парткод: | A63D740200 |
| Деталь: | Stapler unit |
| Парткод: | A3EP560100 |
| Деталь: | FNS Relay harness |
| Парткод: | A63DN12200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A63D740000 |
| Деталь: | COVER |
| Парткод: | A63D741100 |
| Деталь: | GUIDE |
| Парткод: | A63D742101 |
| Деталь: | Label Exchange Staple |
| Парткод: | A63D742300 |
| Деталь: | CUSHION |
| Парткод: | A63D704400 |
| Деталь: | Staple cartridge |
| Парткод: | 9J08P00100 |
| Деталь: | Protection Film |
| Парткод: | A63D171500 |
| Деталь: | Protection Film |
| Парткод: | A63D171600 |
| Деталь: | Sheet /4 |
| Парткод: | A63D742400 |
| Деталь: | STOPPER RING |
| Парткод: | 1033440203 |
| Деталь: | COVER |
| Парткод: | A3GN210800 |
| Деталь: | brushless Motor /20 |
| Парткод: | A61DM10200 |
| Деталь: | Fusing Panel |
| Парткод: | A3GN223000 |
| Деталь: | Drive Gear 68T |
| Парткод: | A3GN220200 |
| Деталь: | BEARING |
| Парткод: | A00F213900 |
| Деталь: | Fusing Panel |
| Парткод: | A3GN223302 |
| Деталь: | Gear 21T |
| Парткод: | A0VD218301 |
| Деталь: | PIN |
| Парткод: | 4036301401 |
| Деталь: | SHAFT |
| Парткод: | A3GN223400 |
| Деталь: | GEAR 32T |
| Парткод: | A92E212500 |
| Деталь: | Gear16T |
| Парткод: | A92E212400 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD219800 |
| Деталь: | CONTACT |
| Парткод: | A3GN130700 |
| Деталь: | Bias Contact |
| Парткод: | A3GN130601 |
| Деталь: | HOLDER |
| Парткод: | A3GN131200 |
| Деталь: | SHAFT |
| Парткод: | A0VD133300 |
| Деталь: | Insulating sheet |
| Парткод: | A3GN136000 |
| Деталь: | HOLDER |
| Парткод: | A3GN130900 |
| Деталь: | HOLDER |
| Парткод: | A3GN131000 |
| Деталь: | HOLDER |
| Парткод: | A3GN131400 |
| Деталь: | COVER |
| Парткод: | A3GN131100 |
| Деталь: | CONTACT |
| Парткод: | A3GN131900 |
| Деталь: | CONTACT |
| Парткод: | A3GN131700 |
| Деталь: | CONTACT |
| Парткод: | A3GN131800 |
| Деталь: | CONTACT |
| Парткод: | A3GN131600 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD220300 |
| Деталь: | BUSHING |
| Парткод: | A3GN213300 |
| Деталь: | CONTACT |
| Парткод: | A3GN135600 |
| Деталь: | CONTACT |
| Парткод: | A3GN135700 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A92ER70000 |
| Деталь: | HOLDER |
| Парткод: | A3GN134001 |
| Деталь: | PAPERFEED SOLENOID |
| Парткод: | A034M20000 |
| Деталь: | PROTECTION PART |
| Парткод: | A3GN708000 |
| Деталь: | WASHER |
| Парткод: | A02E193000 |
| Деталь: | brushless Motor /40 |
| Парткод: | A61DM10400 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN817000 |
| Деталь: | Drive Holder /B |
| Парткод: | A3GN822200 |
| Деталь: | Gear 36/37T |
| Парткод: | A0VD822600 |
| Деталь: | Gear 23T |
| Парткод: | A0VD822800 |
| Деталь: | Gear19T |
| Парткод: | A0VD822700 |
| Деталь: | BUSHING |
| Парткод: | A00F813000 |
| Деталь: | ROLL |
| Парткод: | A00F813100 |
| Деталь: | Torque limiter ASSY |
| Парткод: | A3GN823500 |
| Деталь: | SHAFT |
| Парткод: | A3GN822901 |
| Деталь: | Gear18T |
| Парткод: | A0VD822400 |
| Деталь: | Drive Holder /A |
| Парткод: | A3GN822100 |
| Деталь: | DUCT |
| Парткод: | A92E814000 |
| Деталь: | Guide /Upper |
| Парткод: | A72R820400 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD820700 |
| Деталь: | Neutralizing Brush |
| Парткод: | A3GN825100 |
| Деталь: | GUIDE |
| Парткод: | A72R825600 |
| Деталь: | ROLL |
| Парткод: | A0VD820200 |
| Деталь: | Guide /Lower |
| Парткод: | A72R892301 |
| Деталь: | CONTACT |
| Парткод: | A72R820900 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A72R825200 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD820300 |
| Деталь: | FILTER |
| Парткод: | A92E142300 |
| Деталь: | Reverse/exit Roller |
| Парткод: | A3GN820100 |
| Деталь: | GEAR 14T |
| Парткод: | A0VD821100 |
| Деталь: | CLUTCH |
| Парткод: | A2YFM20000 |
| Деталь: | Drive Side plate |
| Парткод: | A0VD822300 |
| Деталь: | GEAR 24T |
| Парткод: | A0VD822500 |
| Деталь: | CLUTCH |
| Парткод: | A0VD823300 |
| Деталь: | DUP Riverse Drive ASSY |
| Парткод: | A92GR70100 |
| Деталь: | Relay Wiring |
| Парткод: | A3GNN10400 |
| Деталь: | Neutralizing Brush |
| Парткод: | A72R825100 |
| Деталь: | DUCT |
| Парткод: | A92E814200 |
| Деталь: | SEAL |
| Парткод: | A92E142200 |
| Деталь: | GUIDE |
| Парткод: | A3GN813700 |
| Деталь: | DUP Conveyance Assy |
| Парткод: | A3GNR70800 |
| Деталь: | CLUTCH |
| Парткод: | A2YFM20000 |
| Деталь: | Open/close Cover |
| Парткод: | A92E810102 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD702501 |
| Деталь: | BUSHING |
| Парткод: | A3GN702300 |
| Деталь: | Gear16T |
| Парткод: | A0VD235301 |
| Деталь: | ROLL |
| Парткод: | 4138352802 |
| Деталь: | BUSHING |
| Парткод: | 4138353202 |
| Деталь: | ROLLER |
| Парткод: | A3GN702900 |
| Деталь: | ROLLER |
| Парткод: | A3GN702100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD703700 |
| Деталь: | Gear15T |
| Парткод: | A0VD703001 |
| Деталь: | CLUTCH |
| Парткод: | A011M20000 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A3GN703400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD705303 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD703501 |
| Деталь: | BUSHING |
| Парткод: | A0VD702400 |
| Деталь: | SEAL |
| Парткод: | A92E812000 |
| Деталь: | GUIDE |
| Парткод: | A92E811600 |
| Деталь: | Guide /1 |
| Парткод: | A92E708000 |
| Деталь: | Guide /2 |
| Парткод: | A92E708100 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A92E708200 |
| Деталь: | Guide Sheet |
| Парткод: | A92E708300 |
| Деталь: | GROUND PLATE |
| Парткод: | A92E702600 |
| Деталь: | Open/close Stopper |
| Парткод: | A3GN812300 |
| Деталь: | Reinforce Spacer |
| Парткод: | A3GN812200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN110900 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Dust-proof Filter |
| Парткод: | A92E158100 |
| Деталь: | TRANSFER UNIT |
| Парткод: | A4Y5WY4 |
| Деталь: | CONTACT |
| Парткод: | A0VD136800 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A3GN110401 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD114101 |
| Деталь: | SEAL |
| Парткод: | A3GN111800 |
| Деталь: | GROUND SPRING |
| Парткод: | A3GN110600 |
| Деталь: | SEAL |
| Парткод: | A0VD363700 |
| Деталь: | SHUTTER |
| Парткод: | A0VD362300 |
| Деталь: | Holding Lever |
| Парткод: | A3GN110700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A3GN110800 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A3GN110501 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD214700 |
| Деталь: | RAIL /FRONT |
| Парткод: | A3GN110001 |
| Деталь: | RAIL /REAR |
| Парткод: | A3GN110102 |
| Деталь: | SEAL |
| Парткод: | A3GN113300 |
| Деталь: | SEAL |
| Парткод: | A0VD362400 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD362500 |
| Деталь: | Protection Sheet |
| Парткод: | A72R103401 |
| Деталь: | Protection Sheet |
| Парткод: | A72R101000 |
Коды ошибок
C0103
C0104
C0211
C1004
C1014
C1102
C1103
C1108
C1109
C1140
C1146
C1147
C1184
C1403
C2152
C2153
C2154
C2155
C2156
C2253
C2254
C2255
C2256
C2259
C225A
C2350
C2411 ... C2414
C2551, C2553
C2552, C2554
C2555, C2557
C2556, C2558
C2559, C255A, C255B, C255C
C2561, C2562, C2563, C2564
C2650, C265B
C265A
C2A21, C2A22, C2A23, C2A24
C3201
C3202
C3302
C3421
C3426
C3722
C3725
C3726
C3731
C3822
C3825
C3826
C3922
C3925
C3926
C392B
C4091
C40A1 ... C40C5
C4101
C4501
C5102, C5103
C5307
C5351
C5353
C5357
C5360
C5372
C5501
C5601
C5605, C5606
C5610, C5611
C5701
C6001, C6002
C6704
C6751
C6752
C6756
C6F01
C8401
C9401
C9402
CA051, CA052, CA053
CC002
CC140
CC151, CC152, CC156
CC155
CC163
CC164
CC167
CC168
CC169
CC170 ... CC186
CC190
CC191
CC211
CC212
CC213
CC214
CC216
CC301
CC302
CCC00
CD002
CD004, CD00F
CD010
CD011
CD012
CD030
CD041 ... CD046
CD047 ... CD04B
CD050
CD110
CD201, CD202, CD203
CD211, CD212
CD241, CD242
CD261
CD262
CD271
CD272
CD313
CD38E
CD390
CD391
CD392
CD3C0
CD401 ... CD413
CD601, CD602, CD603
CD701, CD702, CD703
CD705, CD706
CDC00
CDC10
CDF50, CDF70, CDFA0
CE001 ... CE011
CE002
CE101
CE201
CE202
CE203
CE301 ... CE305
CED01
CEEE1, CEEE3
CEEE2
CFB00 ... CFF2D
Описание
| Error code: | C0103 |
| Description: | Tray 2 drive motor malfunction (When PF-P20 or PF-P21 is installed) The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | <When PF-P20 or PF-P21 is installed> • Tray 2 drive motor (M1/2) • Tray 2 PC control board (PCCB/2) • CPU board (CPUB) • Base board (BASEB) |
| Remedy: | 1. Check the connector between M1/2-PCCB/2 CN4 for proper connection and correct as necessary. 2. Check the connector between PCCB/2 CN1-relay CN24-BASEB CN21E for proper connection and correct as necessary. 3. Check the connector of M1/2 for proper drive coupling and correct as necessary. 4. Check CPUB for proper installation and correct as necessary. 5. M1/2 load check • Check code: 28 • Multi code: 1, 2 • Control signal: PCCB/2 CN4-1 to 7 • Location of electrical component: 18-P 6. Replace M1/2. 7. PCCB/2 F1 conduction check 8. Replace PCCB/2. 9. Replace CPUB. 10. Replace BASEB. |
| Error code: | C0104 |
| Description: | Tray 3/4 feeder transportation motor failure to turn The lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • LCC transport motor (M25) • Paper feed/transport drive board (PFTDB) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M25-PFTDB CN17 for proper connection and correct as necessary. 2 Check the connector of M25 for proper drive coupling and correct as necessary. 3 M25 operation check PFTDB CN17-1 to 7 11-X. 4 Replace M25. 5 PFTDB ICP6 conduction check. 6 Replace PFTDB. 7 Replace PRCB. |
| Error code: | C0211 |
| Description: | Tray 1 feeder up/down abnormality • The paper feed tray 1 lift-up position sensor is not unblocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The paper feed tray 1 lift-up position sensor is not blocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started. |
| Causes: | • Bypass lift-up motor (M26) • Bypass upper limit sensor (PS35) • Bypass lower limit sensor (PS36) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check the connector of M1 for proper drive coupling and correct as necessary. 3 PS17 I/O check PRCB CN6PRCB-7 (ON) D-2. 4 SL1 operation check PRCB CN6PRCB-4 (ON) D-1. 5 M1 operation check PRCB CN34PRCB-10 (REM) PRCB CN34PRCB-13 (LOCK) D-22. 6 Change SL1. 7 Change M1. 8 Change PRCB. |
| Error code: | C1004 |
| Description: | FNS communication error |
| Causes: | FS control board (FSCB) |
| Error code: | C1014 |
| Description: | FNS communication error (FNS detection) <bizhub C3851FS> In the communication between the MFP board (MFPB) and FS control board (FSCB), when the FS control board (FSCB) is receiving data, a communication error is detected. |
| Causes: | • FS control board (FSCB) • MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Check the connector between FSCB CN1-relay CN600-MFPB CN16E for proper connection and correct as necessary. 4. Replace FSCB. 5. Replace MFPB. |
| Error code: | C1102 |
| Description: | Main tray up/down motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • While the exit tray is being lifted, the main tray upper position sensor (PS26/PS27) is not turned ON (blocked) and the main tray upper position detect switch (SW2) is not turned ON, even after the main tray up/down motor (M11) turns by the set number of times. • While the exit tray is being lowered, the main tray full detection sensor (PS29) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M11) is turned ON. <When FS-537 or FS-537SD is installed> • The main tray lift up detection sensor (PS16/PS17) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/ down motor (M6) is turned ON. • The main tray full detection sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M6) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Main tray up/down motor (M11) • Main tray upper position sensor/R (PS26) • Main tray upper position sensor/F (PS27) • Main tray full detection sensor (PS29) • Main tray upper position detect switch (SW2) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Main tray up/down motor (M6) • Main tray lift up detection sensor/F (PS16) • Main tray lift up detection sensor/R (PS17) • Main tray full detection sensor (PS12) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M11-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M11 for proper drive coupling, and correct as necessary. 3. Check the connector between PS26-relay CN1-FSCB J14 for proper connection and correct as necessary. 4. Check the connector between PS27-relay CN1-FSCB J14 for proper connection and correct as necessary. 5. Check the connector between PS29-relay CN2-FSCB J14 for proper connection and correct as necessary. 6. Check the connector between SW2-FSCB J10 for proper connection and correct as necessary. 7. PS26 I/O check, sensor check • Control signal: FSCB J14<A>-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-C 8. PS27 I/O check, sensor check • Control signal: FSCB J14<B>-6 (ON) • Location of electrical component: FS-536/FS-536SD 3-C 9. PS29 I/O check, sensor check • Control signal: FSCB J14<A>-8 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 10. SW2 operation check • Control signal: FSCB J10-1 to 2 • Location of electrical component: FS-536/FS-536SD 15-K 11. M11 operation check • Control signal: FSCB J9<A>-9 to 10 • Location of electrical component: FS-536/FS-536SD 12-C 12. Replace M11. 13. FSCB F2 conduction check 14. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M6-FSCB J23 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS16-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 4. Check the connector between PS17-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 5. Check the connector between PS12-relay CN9-FSCB J19 for proper connection and correct as necessary. 6. PS16 I/O check, sensor check • Control signal: FSCB J20<B>-4 (ON) • Location of electrical component: FS-537/FS-537SD 11 to 12-D 7. PS17 I/O check, sensor check • Control signal: FSCB J20<B>-7 (ON) • Location of electrical component: FS-537/FS-537SD 12-D 8. PS12 I/O check, sensor check • Control signal: FSCB J19-7 (ON) • Location of electrical component: FS-537/FS-537SD 10-D 9. M6 operation check • Control signal: FSCB J23-1 to 11 • Location of electrical component: FS-537/FS-537SD 13-D 10. Replace M6. 11. FSCB F3 conduction check 12. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1103 |
| Description: | Alignment motor/Front’s drive malfunction. <When FS-536 or FS-536SD is installed> • The alignment plate/F home sensor (PS12) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M7) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. <When FS-537 or FS-537SD is installed> • The alignment plate/F home sensor (PS9) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS9) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M14) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. |
| Causes: | <When FS-536 or FS-536SD is installed> • Alignment motor/Front (M7) • Alignment plate/F home sensor (PS12) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Alignment motor/Front (M14) • Alignment plate/F home sensor (PS9) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M7-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS12-FSCB J4 for proper connection and correct as necessary. 4. PS12 I/O check, sensor check • Control signal: FSCB J4<B>-4 (ON) • Location of electrical component: FS-536/FS-536SD 15-C 5. M7 operation check • Control signal: FSCB J4<A>-5 to 8 • Location of electrical component: FS-536/FS-536SD 14-C 6. Replace M7. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M14-relay CN5-FSCB J18 for proper connection and correct as necessary. 2. Check the connector of M14 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-relay CN5-FSCB J18 for proper connection and correct as necessary. 4. PS9 I/O check, sensor check • Control signal: FSCB J18-10 (ON) • Location of electrical component: FS-537/FS-537SD 6-D 5. M14 operation check • Control signal: FSCB J18-1 to 4 • Location of electrical component: FS-537/FS-537SD 6-D 6. Replace M14. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1108 |
| Description: | Stapler rotation motor drive failure |
| Causes: | • Stapler unit • FS control board (FSCB) |
| Error code: | C1109 |
| Description: | Stapler motor’s malfunction. <When FS-536 or FS-536SD is installed> • The stapler home position sensor (rear) (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler motor (M14) turned ON. • The stapler position sensor (center) (PS24) is turned ON (blocked), when the stapler motor (M14) is running. <When FS-537 or FS-537SD is installed> • The stapler home position sensor (PS18/PS19) is not turned (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler movement motor (M5) turned ON. • The stapler position sensor (center) (PS20) is turned ON (blocked), when the stapler motor (M5) is running. |
| Causes: | <When FS-536 or FS-536SD is installed> • Stapler unit • Stapler home position sensor (rear) (PS23) • Stapler position sensor (center) (PS24) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler unit • Stapler home position sensor (corner) (PS18) • Stapler home position sensor (rear) (PS19) • Stapler position sensor (center) (PS20) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between the stapler unit-relay CN4-FSCB J11 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. Check the connector between PS24-relay CN3-FSCB J11 for proper connection and correct as necessary. 5. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 6. PS24 I/O check, sensor check • Control signal: FSCB J11<B>-6 • Location of electrical component: FS-536/FS-536SD 5-C 7. Replace the stapler unit. 8. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between the stapler unit-FSCB J17 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS18-FSCB J16 for proper connection and correct as necessary. 4. Check the connector between PS19-FSCB J16 for proper connection and correct as necessary. 5. Check the connector between PS20-FSCB J16 for proper connection and correct as necessary. 6. PS18 I/O check, sensor check • Control signal: FSCB J16-9 • Location of electrical component: FS-537/FS-537SD 15-D 7. PS19 I/O check, sensor check • Control signal: FSCB J16-6 • Location of electrical component: FS-537/FS-537SD 15-D 8. PS20 I/O check, sensor check • Control signal: FSCB J16-3 • Location of electrical component: FS-537/FS-537SD 15-D 9. Replace the stapler unit. 10. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1140 |
| Description: | PF lift motor error Object: Side feeder |
| Causes: | 1. The PF lift upper limit sensor does not turn on when passing 30s after cassette 5 is inserted. 2. The lock-up signal is detected for 200ms continuously during the PF lift motor operation. 3. The PF lift upper limit sensor does not turn on when passing 2s after the upper limit control when printing starts. |
| Remedy: | 1 Checking the bottom plate The bottom plate does not operate properly. Repair or replace the bottom plate when it does not move vertically. 2 Checking the drive gear The drive gear to lift up the bottom plate does not rotate properly. Check if the drive gears to lift up the bottom plate rotate smoothly or have no excessive load. And apply the grease to the frictional parts and fix the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor - PF main PWB Wiring diagram 4 Checking the PF lift motor The PF lift motor is faulty. Replace the PF lift motor. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift upper limit sensor - PF main PWB Wiring diagram 6 Checking the PF lift upper limit sensor The PF lift upper limit sensor is not properly attached or faulty. Reattach the PF lift upper limit sensor. Then, replace it if it is not fixed. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1146 |
| Description: | Trailing edge stopper motor/R malfunction. <When FS-537 or FS-537SD is installed> The trailing edge stopper home position detection sensor/R (PS7) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the trailing edge stopper motor/R (M11) is turned ON. |
| Causes: | <When FS-537 or FS-537SD is installed> • Trail edge stopper motor/R (M11) • Trail edge stopper sensor/R (PS7) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M11-relay CN4-relay CN3-FSCB J21 for proper connection and correct as necessary. 2. Check the connector of M11 for proper drive coupling, and correct as necessary. 3. Check the connector between PS7-relay CN4-relay CN3-FSCB J21 for proper connection and correct as necessary. 4. PS7 I/O check, sensor check • Control signal: FSCB J21-16 (ON) • Location of electrical component: FS-537/FS-537SD 5-D 5. M11 operation check • Control signal: FSCB J21-17 to 20 • Location of electrical component: FS-537/FS-537SD 5-D 6. Replace M11. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1147 |
| Description: | FD trailing edge pushing motor malfunction <bizhub C3851FS> • The FD trailing edge home sensor (FSPS4) is not turned OFF (unblocked) even after the lapse of a given period of time after the FD trailing edge pushing motor (FSM4) is turned ON at start from the home position. • The FD trailing edge pushing motor (FSM4) is not drive completion after the set period of time has elapsed even after the start of driving. • The FD trailing edge home sensor (FSPS4) is not turned ON (blocked) even after the lapse of a given period of time after the FD trailing edge pushing motor (FSM4) is turned ON at the initial operation. |
| Causes: | • FD trailing edge pushing motor (FSM4) • FD trailing edge home sensor (FSPS4) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between FSM4-relay CN20-FSCB CN3 for proper connection and correct as necessary. 2. Check the connector of FSM4 for proper drive coupling, and correct as necessary. 3. Check the connector between FSPS4-FSCB CN10 for proper connection and correct as necessary. 4. FSPS4 I/O check, sensor check • Control signal: FSCB CN10-10 • Location of electrical component: 24 to 25-Q 5. FSM4 operation check • Control signal: FSCB CN3-9 to 12 • Location of electrical component: 23-Q 6. Replace FSM4. 7. Replace FSCB. |
| Error code: | C1184 |
| Description: | Paper discharge control motor malfunction. <When FS-536 or FS-536SD is installed> The paper delivery control sensor (PS28) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed while the paper receiving control motor (M12) is energized. <When FS-537 or FS-537SD is installed> The paper delivery control sensor (PS11) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed while the paper receiving control motor (M15) is energized. |
| Causes: | <When FS-536 or FS-536SD is installed> • Paper receiving control motor (M12) • Paper delivery control sensor (PS28) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Paper receiving control motor (M15) • Paper delivery control sensor (PS11) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M12-relay CN1-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M12 for proper drive coupling and correct as necessary. 3. Check the connector between PS28-relay CN1-FSCB J14 for proper connection and correct as necessary. 4. PS28 I/O check, sensor check • Control signal: FSCB J14<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 2 to 3-C 5. M12 operation check • Control signal: FSCB J14<A>-9 to 12 • Location of electrical component: FS-536/FS-536SD 2-C 6. Replace M12. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M15-FSCB J19 for proper connection and correct as necessary. 2. Check the connector of M15 for proper drive coupling and correct as necessary. 3. Check the connector between PS11-relay CN10<A>-FSCB J20 for proper connection and correct as necessary. 4. PS11 I/O check, sensor check • Control signal: FSCB J20<A>-3 (ON) • Location of electrical component: FS-537/FS-537SD 10-D 5. M15 operation check • Control signal: FSCB J19-1 to 4 • Location of electrical component: FS-537/FS-537SD 10-D 6. Replace M15. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1403 |
| Description: | PK flash ROM error. <When FS-537+PK-523 or FS-537SD+PK-523 is installed> Data of flash ROM of the PK is determined to be faulty when the main power switch is turned ON. |
| Causes: | Punch control board (PKCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace PKCB. |
| Error code: | C2152 |
| Description: | Transfer belt pressure welding alienation • During a retraction operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its retracted position within a predetermined period of time after the transfer belt retraction clutch is turned ON. • During a pressure operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its pressed position within a predetermined period of time after the transfer belt clutch is turned ON. |
| Causes: | • 1st transfer pressure sensor/K (PS51) • 1st transfer pressure sensor/YMC (PS52) • 1st transfer pressure motor (M21) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 PS31 I/O check PRCB CN36PRCB-15 (ON) D-26 to 27. 3 CL7 operation check PRCB CN39PRCB-10 (ON) D-23. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change CL7. 6 Change M5. 7 Change PRCB. |
| Error code: | C2153 |
| Description: | The 1st transfer pressure sensor (PS9) does not detect “switch from pressure to retraction” within a given period time after the 1st transfer pressure solenoid (SD1) turned ON. |
| Causes: | • Main motor (M1) • 1st transfer pressure solenoid (SD1) • 1st transfer pressure sensor (PS9) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M1-MFPB CN6E for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-MFPB CN9E for proper connection and correct as necessary. 4. Check the connector between SD1-relay CN85-MFPB CN9E for proper connection and correct as necessary. 5. PS9 I/O check, sensor check • Control signal: MFPB CN9E-3 (ON) • Location of electrical component: 3-C 6. SD1 operation check • Control signal: MFPB CN9E-12 (REM) • Location of electrical component: 4-C 7. M1 operation check • Control signal: MFPB CN6E-4 to 7 • Location of electrical component: 2-C 8. Replace M1. 9. MFPB F4E conduction check 10. Replace MFPB. |
| Error code: | C2154 |
| Description: | Transfer belt contact fault at all pressure switching The 1st transfer pressure sensor (PS9) does not detect “switch from retraction to pressure” within a given period time after the 1st transfer pressure solenoid (SD1) turned ON. |
| Causes: | • Main motor (M1) • 1st transfer pressure solenoid (SD1) • 1st transfer pressure sensor (PS9) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M1-MFPB CN6E for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-MFPB CN9E for proper connection and correct as necessary. 4. Check the connector between SD1-relay CN85-MFPB CN9E for proper connection and correct as necessary. 5. PS9 I/O check, sensor check • Control signal: MFPB CN9E-3 (ON) • Location of electrical component: 3-C 6. SD1 operation check • Control signal: MFPB CN9E-12 (REM) • Location of electrical component: 4-C 7. M1 operation check • Control signal: MFPB CN6E-4 to 7 • Location of electrical component: 2-C 8. Replace M1. 9. MFPB F4E conduction check 10. Replace MFPB. |
| Error code: | C2155 |
| Description: | Transfer belt contact fault after K pressure established The 1st transfer pressure sensor (PS9) is turned ON (blocked) after the lamps of given time after the 1st transfer pressure solenoid (SD1) turned OFF when the release operation is finished. |
| Causes: | • Main motor (M1) • 1st transfer pressure solenoid (SD1) • 1st transfer pressure sensor (PS9) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M1-MFPB CN6E for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-MFPB CN9E for proper connection and correct as necessary. 4. Check the connector between SD1-relay CN85-MFPB CN9E for proper connection and correct as necessary. 5. PS9 I/O check, sensor check • Control signal: MFPB CN9E-3 (ON) • Location of electrical component: 3-C 6. SD1 operation check • Control signal: MFPB CN9E-12 (REM) • Location of electrical component: 4-C 7. M1 operation check • Control signal: MFPB CN6E-4 to 7 • Location of electrical component: 2-C 8. Replace M1. 9. MFPB F4E conduction check 10. Replace MFPB. |
| Error code: | C2156 |
| Description: | Transfer belt spacing fault after all pressure established The 1st transfer pressure sensor (PS9) is turned OFF (unblocked) after the laps of given time after the 1st transfer pressure solenoid (SD1) turned OFF when the pressing operation is finished. |
| Causes: | • Main motor (M1) • 1st transfer pressure solenoid (SD1) • 1st transfer pressure sensor (PS9) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M1-MFPB CN6E for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-MFPB CN9E for proper connection and correct as necessary. 4. Check the connector between SD1-relay CN85-MFPB CN9E for proper connection and correct as necessary. 5. PS9 I/O check, sensor check • Control signal: MFPB CN9E-3 (ON) • Location of electrical component: 3-C 6. SD1 operation check • Control signal: MFPB CN9E-12 (REM) • Location of electrical component: 4-C 7. M1 operation check • Control signal: MFPB CN6E-4 to 7 • Location of electrical component: 2-C 8. Replace M1. 9. MFPB F4E conduction check 10. Replace MFPB. |
| Error code: | C2253 |
| Description: | Color PC motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/YMC (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2254 |
| Description: | Color PC motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/YMC motor (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2255 |
| Description: | Developing motor’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Developing motor/YMC (M17) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M21-PRCB CN32 for proper connection and correct as necessary. 2 Check the M21 connector for proper drive coupling and correct as necessary. 3 M21 operation check PRCB CN32-2 (REM) PRCB CN32-5 (LOCK). bizhub C224 25-I to J 4 Replace M21. 5 Replace PRCB. |
| Error code: | C2256 |
| Description: | Developing motor’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Developing motor/YMC (M17) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M21-PRCB CN32 for proper connection and correct as necessary. 2 Check the M21 connector for proper drive coupling and correct as necessary. 3 M21 operation check PRCB CN32-2 (REM) PRCB CN32-5 (LOCK). bizhub C224 25-I to J 4 Replace M21. 5 Replace PRCB. |
| Error code: | C2259 |
| Description: | Developing motor/K’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Developing motor/K (M19) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M19-PRCB CN22 for proper connection and correct as necessary. 2 Check the M19 connector for proper drive coupling and correct as necessary. 3 M19 operation check PRCB CN22-1 to 5 16-K. 4 Replace M19. 5 PRCB ICP6 conduction check. 6 Replace PRCB. |
| Error code: | C225A |
| Description: | Developing motor/K’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Developing motor/K (M19) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M19-PRCB CN22 for proper connection and correct as necessary. 2 Check the M19 connector for proper drive coupling and correct as necessary. 3 M19 operation check PRCB CN22-1 to 5 16-K. 4 Replace M19. 5 PRCB ICP6 conduction check. 6 Replace PRCB. |
| Error code: | C2350 |
| Description: | Toner suction fan failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Toner suction fan (FM7) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM7-relay CN326-MFPB CN24E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM7 operation check • Control signal: MFPB CN24E-7 (DRIVE), MFPB CN24E-9 (LOCK) • Location of electrical component: 1-K 4. Replace FM7. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C2411 ... C2414 |
| Description: | • C2411: Imaging unit/C new article release • C2412: Imaging unit/M new article release • C2413: Imaging unit/Y new article release • C2414: Imaging unit/K new article release The status with the new unit is not cleared after the new imaging unit is set. |
| Causes: | • Imaging unit/C,M,Y,K • CPU board (CPUB) • Base board (BASEB) |
| Remedy: | 1. Reinstall the imaging unit. 2. Check the connector between the imaging unit/C-relay CN5-BASEB CN14E for proper connection and correct as necessary. (C2411) 3. Check the connector between the imaging unit/M-relay CN8-BASEB CN14E for proper connection and correct as necessary. (C2412) 4. Check the connector between the imaging unit/Y-relay CN7-BASEB CN14E for proper connection and correct as necessary. (C2413) 5. Check the connector between the imaging unit/K-relay CN6-BASEB CN14E for proper connection and correct as necessary. (C2414) 6. Check CPUB for proper installation and correct as necessary. 7. Replace the corresponding imaging unit. 8. Replace CPUB. 9. Replace BASEB. |
| Error code: | C2551, C2553 |
| Description: | • C2551: Abnormally low toner density detected cyan TCR sensor • C2553: Abnormally low toner density detected magenta TCR sensor When sampling data is determined in TC ratio calculation control, TCR sensor output is lower than a predetermined value for a predetermined number of times in a row even though there is toner in the toner cartridge. |
| Causes: | • Imaging unit/Y,M,C,K • Toner supply motor/YM (M5) • Toner supply motor/CK (M6) • MFP board (MFPB) |
| Remedy: | 1. Perform image troubleshooting procedure if image density is low. 2. Reinstall the imaging unit. 3. Check the connector between imaging unit-MFPB CN19E, CN20E for proper connection and correct as necessary. 4. Check the connector between M5-MFPB CN8E for proper connection and correct as necessary. 5. Check the connector between M6-MFPB CN8E for proper connection and correct as necessary. 6. M5, M6 operation check • Control signal: MFPB CN8E-1 to 4 (M5), MFPB CN8E-5 to 8 (M6) • Location of electrical component: 23-C 7. Replace the imaging unit. 8. MFPB F5E conduction check 9. Replace MFPB. |
| Error code: | C2552, C2554 |
| Description: | • C2552: Abnormally high toner density detected cyan TCR sensor • C2554: Abnormally high toner density detected magenta TCR sensor. |
| Causes: | The TC ratio of the toner determined by the toner replenishment control is detected to be the predetermined value or over for consecutive times. |
| Remedy: | • Developing unit/C,M,Y,K • Toner cartridge/C,M,Y,K • Front side board (FRB) • MFP board (MFPB) |
| Error code: | C2555, C2557 |
| Description: | • C2555: Abnormally low toner density detected yellow TCR sensor • C2557: Abnormally low toner density detected black TCR sensor When sampling data is determined in TC ratio calculation control, TCR sensor output is lower than a predetermined value for a predetermined number of times in a row even though there is toner in the toner cartridge. |
| Causes: | • Imaging unit/Y,M,C,K • Toner supply motor/YM (M5) • Toner supply motor/CK (M6) • MFP board (MFPB) |
| Remedy: | 1. Perform image troubleshooting procedure if image density is low. 2. Reinstall the imaging unit. 3. Check the connector between imaging unit-MFPB CN19E, CN20E for proper connection and correct as necessary. 4. Check the connector between M5-MFPB CN8E for proper connection and correct as necessary. 5. Check the connector between M6-MFPB CN8E for proper connection and correct as necessary. 6. M5, M6 operation check • Control signal: MFPB CN8E-1 to 4 (M5), MFPB CN8E-5 to 8 (M6) • Location of electrical component: 23-C 7. Replace the imaging unit. 8. MFPB F5E conduction check 9. Replace MFPB. |
| Error code: | C2556, C2558 |
| Description: | • C2556: Abnormally high toner density detected yellow TCR sensor • C2558: Abnormally high toner density detected black TCR sensor. The TC ratio of the toner determined by the toner replenishment control is detected to be the predetermined value or over for consecutive times. |
| Causes: | • Developing unit/C,M,Y,K • Toner cartridge/C,M,Y,K • Front side board (FRB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Reinstall toner cartridge. 3. Check the connector between the developing unit-FRB CN13 (C2558), CN14 (C2552), CN15 (C2554), CN16 (C2556) for proper connection and correct as necessary. 4. Check the connector between FRB CN1, CN3-MFPB CN4E, CN11E for proper connection and correct as necessary. 5. Replace the developing unit. 6. Replace FRB. 7. Replace MFPB. |
| Error code: | C2559, C255A, C255B, C255C |
| Description: | • C2559: Cyan TCR sensor adjustment failure • C255A: Magenta TCR sensor adjustment failure • C255B: Yellow TCR sensor adjustment failure • C255C: Black TCR sensor adjustment failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • MFP board (MFPB) |
| Remedy: | 1. Reinstall imaging unit. 2. Check the connector between imaging unit-MFPB CN19E, CN20E for proper connection and correct as necessary. 3. Replace the imaging unit. 4. Replace MFPB. |
| Error code: | C2561, C2562, C2563, C2564 |
| Description: | • C2561: Cyan TCR sensor failure • C2562: Magenta TCR sensor failure • C2563: Yellow TCR sensor failure • C2564: Black TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • MFP board (MFPB) |
| Remedy: | 1. Reinstall imaging unit. 2. Check the connector between imaging unit-MFPB CN19E, CN20E for proper connection and correct as necessary. 3. Replace the imaging unit. 4. Replace MFPB. |
| Error code: | C2650, C265B |
| Description: | • C2650: Main backup media access 1 error • C265B: Main backup media access 2 error • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. • The main body detects that the back up board is not mounted. |
| Causes: | • C2650: Back up board/1 (ERB/1) • C265B: Back up board/2 (ERB/2) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between ERB-MFPB CN5E for proper connection and correct as necessary. 2. Replace MFPB. 3. Replace ERB. (ERB/1 / ERB/2) 4. If the above actions do not solve the problem, contact KM. |
| Error code: | C265A |
| Description: | Main backup media wrongly installation. The ERB/1 and ERB/2 are mounted in a reverse direction. |
| Causes: | • Back up board/1 (ERB/1) • Back up board/2 (ERB/2) |
| Remedy: | 1. Check to see if the ERB/1 and ERB/2 are mounted in a reverse direction. 2. Check the type of the installed ERB and replace it if it is a wrong one. 3. Replace ERB. (ERB/1 / ERB/2) |
| Error code: | C2A21, C2A22, C2A23, C2A24 |
| Description: | • C2A21: Toner cartridge/C new release failure • C2A22: Toner cartridge/M new release failure • C2A23: Toner cartridge/Y new release failure • C2A24: Toner cartridge/K new release failure. Trouble detection condition The status with the new cartridge is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/Y,M,C,K • MFP board (MFPB) |
| Remedy: | 1. Reinstall the toner cartridge 2. Clean the connection between the toner cartridge and the machine if dirty. 3. Check the connector between the toner cartridge-MFPB CN18E for proper connection and correct as necessary. 4. Replace the toner cartridge 5. Replace MFPB. |
| Error code: | C3201 |
| Description: | Fusing motor failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3202 |
| Description: | Fusing motor turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3302 |
| Description: | Fusing cooling fan motor/ 2,3 failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Paper cooling fan (FM8) • Printer control board (PRCB) |
| Remedy: | 1 Check the FM10 or FM11 connector for proper connection and correct as necessary 2 Check the fan for possible overload and correct as necessary. 3 FM10/FM11 operation check PRCB CN40PRCB-5 (ON) PRCB CN40PRCB-6 (LOCK) D-19. PRCB CN40PRCB-8 (ON) PRCB CN40PRCB-9 (LOCK) D-18. 4 Change FM10/FM11. 5 Change PRCB. |
| Error code: | C3421 |
| Description: | Fusing heaters trouble (heating side) • The temperature detected by the heating roller thermistor/C does not reach a predetermined level after the lapse of a predetermined period of time after the heating roller fusing heater lamp lights up. • The difference between the maximum and minimum temperatures detected by the heating roller thermistor/C within a predetermined period of time after the start of a warm-up cycle is below or above a predetermined value. • The temperature detected after a pressure level correction remains under a predetermined level even after the lapse of a predetermined period of time after the start of the temperature detection. • During a warm-up, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. |
| Causes: | • Fusing unit • C3421: Fusing temperature sensor/1 (TEM1: center) • C3426: Fusing temperature sensor/1 (TEM1: edge) • DC power supply (DCPS) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3426 |
| Description: | Fusing temperature increase malfunction (TEM1: edge) • Detected temperature of the fusing temperature sensor/1 (TEM1: center and edge) does not go up a given range of temperature even after a lapse of given period of time at warm up. • The warm-up is not completed even after the set period of time has elapsed after the warm-up is started. |
| Causes: | • Fusing unit • C3421: Fusing temperature sensor/1 (TEM1: center) • C3426: Fusing temperature sensor/1 (TEM1: edge) • DC power supply (DCPS) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the right door. 3. Check the fusing unit-MFPB CN13E, DCPS CN2 for proper connection and correct as necessary. 4. Replace the fusing unit. 5. Replace MFPB. 6. DCPS F102 conduction check 7. Replace DCPS. |
| Error code: | C3722 |
| Description: | Fusing abnormally high temperature detection (Edge of the heating side) Detected temperature of the heating roller thermistor/1 (TH1) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3725 |
| Description: | Fusing abnormally high temperature detection (Main of the heating side) • Detected temperature of the heating roller temperature sensor (TEMS) goes beyond a given temperature for a given period of time consecutively. • The hard protector signal error is detected for a given period of time consecutively. |
| Causes: | • Fusing unit • Heating roller temperature sensor (TEMS2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3726 |
| Description: | Fusing abnormally high temperature detection (Center of the heating side) Detected temperature of the heating roller thermistor/2 (TH2) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • Heating roller thermistor/2 (TH2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3731 |
| Description: | Fusing abnormally high temperature (Hard protector). An abnormally high temperature of the hard protector signal is detected. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • Fusing belt temperature sensor/2 (TEMS2) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/2 (TEMS2) (bizhub 808/758) • Fusing belt temperature sensor/3 (TEMS3) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/3 (TEMS3) (bizhub 808/758) • Pressure roller thermistor/2 (TH3) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1, TEMS2, TEMS3-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Replace the fusing unit. 6. Replace TEMS1, TEMS2, TEMS3. 7. Replace MFPB. |
| Error code: | C3822 |
| Description: | Fusing abnormally low temperature detection (Edge of the heating roller) The heating roller thermistor/3 continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, IHPU, NF1 and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace IHPU. 6 Replace PRCB. 7 Replace NF1. |
| Error code: | C3825 |
| Description: | Fusing abnormally low temperature detection (Main of the heating roller) The heating roller temperature sensor (TEMS) continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller temperature sensor (TEMS2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 PRCB ICP15 conduction check. 6 Replace PRCB. |
| Error code: | C3826 |
| Description: | Fusing abnormally low temperature detection (Center of the heating roller) The heating roller thermistor/2 (TH2) continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller thermistor/2 (TH2) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 PRCB ICP15 conduction check. 6 Replace PRCB. |
| Error code: | C3922 |
| Description: | Fusing sensor wire breaks detection (Edge of the heating roller) After a predetermined period of time after the warm-up stage is started, the heating roller thermistor/1 (TH1) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3925 |
| Description: | Fusing sensor wire breaks detection (Center of the heating roller) After a predetermined period of time after the warm-up stage is started, the heating roller temperature sensor (TEMS) voltage does not increase by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller temperature sensor (TEMS2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3926 |
| Description: | Fusing sensor wire breaks detection (Middle of the heating roller) • After a predetermined period of time after the warm-up stage is started, the heating roller thermistor/2 (TH2) voltage does not decrease by predetermined steps (temperature rise) within a predetermined time. • When a temperature detected by the heating roller thermister/1 (TH1) is compared with the temperature detected by the heating roller thermister/2 (TH2) to find out that the difference exceeded the predetermined temperature. |
| Causes: | • Fusing unit • Heating roller thermistor/2 (TH2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C392B |
| Description: | Fusing disconnection error detection (difference of temperature) bizhub 958, bizhub PRO 958: The difference between the temperature corrected by the fusing belt thermistor/1 (TH1) and the temperature detected by the fusing belt temperature sensor/1 (TEMS1) exceeds a predetermined value after warm up. bizhub 808/758: The difference between the temperature corrected by the heating roller thermistor/1 (TH1) and the temperature detected by the heating roller temperature sensor/1 (TEMS1) exceeds a predetermined value after warm up. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • Fusing belt thermistor/1 (TH1) (bizhub 958, bizhub PRO 958) • Heating roller thermostat/1 (TH1) (bizhub 808/758) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Check the connector between NF1 CN2-IHPU CN1 for proper connection and correct as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Replace the fusing unit. 8. Replace IHPU. 9. Replace MFPB. 10. Replace NF1. |
| Error code: | C4091 |
| Description: | I/F communication error. The communication between the MFPB and PRCB can not be completed even when elapsed a given period of time. |
| Causes: | • MFP board (MFPB) • Printer control board (PRCB) |
| Remedy: | 1 Reboot the machine. 2 Check the flat cable between MFPB PJ03-PRCB CN41 for proper connection and correct as necessary. 3 Check the connected portion of the flat cable for any curled pattern or any scratches, and replace it if necessary. 4 Replace MFPB 5 Replace PRCB |
| Error code: | C40A1 ... C40C5 |
| Description: | • C40A1: Mechanical controller sub-CPU communication error • C40A2: Mechanical controller PF communication data error • C40A3: Mechanical controller PF transmission timeout • C40A4: Mechanical controller PF communication pulse error • C40C3: CTL PF transmission timeout 1 • C40C5: CTL PF transmission timeout 2 A CPU communication error is detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. MFPB F2E conduction check 4. Replace MFPB. |
| Error code: | C4101 |
| Description: | BD initialization error |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4501 |
| Description: | Laser malfunction. • SOS signal is not detected even after the lapse of a given period of time after starting the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Causes: | • PH unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between the PH unit-PHRYB CN8 for proper connection and correct as necessary. 2. Replace the PH unit. 3. PHRYB IC5 conduction check. 4. Replace PHRYB. 5. Replace MFPB. |
| Error code: | C5102, C5103 |
| Description: | • C5102: Transport motor failure to turn • C5103: Transport motor turning at abnormal timing. • C5102: The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. • C5103: The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Transport motor (M1) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M1-MFPB CN8E for proper connection and correct as necessary. 2. Check the loading status of the transfer belt drive, and correct the error as necessary. 3. M1 operation check • Control signal: MFPB CN8E-3 (REM), MFPB CN8E-6 (LOCK) • Location of electrical component: 2-C 4. Replace M1. 5. Replace MFPB. |
| Error code: | C5307 |
| Description: | UFP fan motor failure The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • UFP fan motor (FM5) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM5-relay CN158-relay CN90-MFPB CN10E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM5 operation check • Control signal: MFPB CN10E-9 (LOCK) • Location of electrical component: 5-C 4. Replace FM5. 5. MFPB F2E and F4E conduction check 6. Replace MFPB. |
| Error code: | C5351 |
| Description: | Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • DC power supply cooling fan (FM9) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1 Check the FM5 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check PRCB CN30PRCB-11 (ON) PRCB CN30PRCB-12 (LOCK) K-8. 4 Change FM5. 5 Change DCPU. 6 Change PRCB. |
| Error code: | C5353 |
| Description: | Cooling fan motor/2’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Cooling fan motor/2 (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM2 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM2 operation check PRCB CN28PRCB-2 (ON) PRCB CN28PRCB-3 (LOCK) D-24. 4 Change FM2. 5 Change PRCB. |
| Error code: | C5357 |
| Description: | Cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Machine cooling fan (FM1) • CPU board (CPUB) • Base board (BASEB) |
| Remedy: | 1 Check the FM1 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM1 operation check PRCB CN30PRCB-4 (ON) PRCB CN30PRCB-6 (LOCK) K-7. 4 Change FM1. 5 Change PRCB. |
| Error code: | C5360 |
| Description: | Exhaust fan 1 failure to turn (When CU-102 is installed). The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Exhaust fan 1 (FM14) • Clean unit drive board (CUDB) • Process drive board (PDB) |
| Remedy: | 1. Check the connector between FM14-relay CN316-CUDB CN2 for proper connection and correct as necessary. 2. Check the connector between CUDB CN1-relay CN315-PDB CN6 for proper connection and correct as necessary. 3. Check the fan for possible overload and correct as necessary. 4. FM14 load check • Check code: 42 • Multi code: 27 • Control signal: CUDB CN2-1 (REM), CUDB CN2-3 (LOCK) • Location of electrical component: 16-Y 5. Replace FM14. 6. Replace CUDB. 7. PDB PS1 conduction check 8. Replace PDB. |
| Error code: | C5372 |
| Description: | MFP control board CPU temperature failure. Temperature failure of CPU on the MFP board was detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Reboot the machine. 2. Check for clogging in the ventilation path between the MFPB and the power supply cooling fan, and correct as necessary. 3. Replace MFPB. |
| Error code: | C5501 |
| Description: | AC signal abnormality The zero cross signal is not input during fusing phase control. |
| Causes: | • Fusing unit • DC power supply (DCPU) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU and PRCB for proper connection and correct or change as necessary. 3 Replace fusing unit. 4 Replace PRCB. 5 Replace DCPU. |
| Error code: | C5601 |
| Description: | Engine control malfunction. Engine control malfunction is detected with port monitor control. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | C5605, C5606 |
| Description: | • C5605: Engine communication data error • C5606: Engine transmission timeout. A communication error is detected between CPUs. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | C5610, C5611 |
| Description: | • C5610: PH LD drive communication error • C5611: PH EEPROM communication error. Trouble detection condition • C5610: LD drive write data and read data disagree with each other a predetermined number of consecutive times. • C5611: The two-time readout data of PH unit EEPROM data keeps mismatched for a predetermined number of consecutive times. |
| Causes: | • PH unit • MFP board (MFPB) |
| Remedy: | 1. Reboot the machine. 2. Check the connector between PH unit-relay CN73-MFPB CN21E for proper connection and correct as necessary. 3. Replace the PH unit. (bizhub C3851/C3351 / bizhub C3851FS) 4. Replace MFPB. |
| Error code: | C5701 |
| Description: | Power supply malfunction. A condition is detected in which no power is being supplied to the base board (BASEB). |
| Causes: | • Front door sensor (PS1) • Right door sensor (PS2) • Front door switch (SW2) • Right door switch (SW5) • DC power supply (DCPS) • CPU board (CPUB) • Base board (BASEB) |
| Remedy: | 1. Check the connector between PS1, PS2-BASEB CN16E for proper connection and correct as necessary. 2. Check the connector between SW2, SW5-relay CN36-DCPS CN3 for proper connection and correct as necessary. 3. Check the connector between DCPS CN4-BASEB CN3E for proper connection and correct as necessary. 4. Check the connector between DCPS CN6-BASEB CN1E for proper connection and correct as necessary. 5. Check CPUB for proper installation and correct as necessary. 6. Replace CPUB. 7. BASEB F5E conduction check 8. Replace BASEB. 9. Replace DCPS. |
| Error code: | C6001, C6002 |
| Description: | • C6001: DF related configuration error 1 • C6002: DF related configuration error 2. Inconsistency in the configuration with the installed DF is detected on the main body. |
| Causes: | • DF drive board (DFDB) • MFP board (MFPB) |
| Remedy: | 1. Check the type of the installed DF and replace it if it is a wrong one. 2. Check the connector between DFDB J1-MFPB CN800E for proper connection and correct as necessary. 3. Replace DFDB. 4. Replace MFPB. |
| Error code: | C6704 |
| Description: | Image input time out. Image data is not input from the scanner to the MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Memory Bus Check] -> [Scanner -> Memory], and conduct the memory bus function. 2. Correct the harness connection between scanner section and MFPB if faulty. 3. MFPB F3E conduction check 4. Replace MFPB. 5. Replace the CCD unit. |
| Error code: | C6751 |
| Description: | CCD gain adjustment failure. • The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment. |
| Causes: | • LED exposure unit • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 2. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 3. Correct the harness connection between SCDB CN1-DCPU CN005 if faulty. 4. Check for possible extraneous light and correct as necessary. 5. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 6. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 7. Replace SCDB 8. Replace the CCD unit. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | C6752 |
| Description: | ASIC clock input error (front side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on CCD board (CCDB) was conducted, and verification failure was detected. |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Correct the harness connection of CCDB if faulty. 2. Replace the CCD unit. 3. MFPB F3E conduction check 4. Replace MFPB. |
| Error code: | C6756 |
| Description: | CCD power-supply voltage malfunction. Power is not supplied to CCD after the lapse of a given period of time after the main power switch is turned ON or the machine recovers from the sleep mode. |
| Causes: | • CCD board (CCDB) • Scanner drive board (SCDB) • DC power supply unit (DCPU) |
| Remedy: | 1. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 2. Correct the harness connection between SCDB CN1 and DCPU CN005 if faulty. 3. Replace the CCD unit. 4. Replace SCDB. 5. Replace DCPU. |
| Error code: | C6F01 |
| Description: | Scanner sequence trouble 1. The original transport interval becomes shorter than the predetermined value due to an original transport control error in original reading in DF. |
| Causes: | • MFP board (MFPB) • DF control board (DFCB) |
| Remedy: | 1. Correct the harness connection between main body and DF if faulty. 2. Replace DFCB. 3. Replace MFPB. |
| Error code: | C8401 |
| Description: | Nonvolatile memory error. The EEPROM writing is disabled. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Check the DFCB connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Replace DFCB. |
| Error code: | C9401 |
| Description: | Exposure LED lighting failure The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | C9402 |
| Description: | Exposure LED lighting abnormally The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | CA051, CA052, CA053 |
| Description: | • CA051: Standard controller configuration failure • CA052: Controller hardware error • CA053: Controller start failure • CA051: The controller of the MFP board (MFPB) is faulty. • CA052: A controller hardware error is detected in the network interface. • CA053: A controller start failure is detected in the controller interface. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check to see if [Service Mode] -> [System 2] -> [Image Controller Setting] has been set to “Controller 0.” If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. 2. Check the connectors of the MFPB for proper connection and correct as necessary. 3. Replace MFPB. |
| Error code: | CC002 |
| Description: | Vendor internal error. Error occurs inside the vendor. |
| Causes: | • Vendor • MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. Turn OFF and ON the power switch at the vendor side. 2. Check the connector between the vendor-MFPB CN1E for proper connection and correct as necessary. 3. Replace MFPB. 4. Replace the vendor. |
| Error code: | CC140 |
| Description: | Trouble related to security. |
| Causes: | Trouble related to security. |
| Remedy: | Contact the responsible people of KM before taking some countermeasures. |
| Error code: | CC151, CC152, CC156 |
| Description: | • CC151: ROM contents error upon startup (MSC) • CC152: ROM contents error upon startup (IR) • CC156: DF ROM error. Trouble detection condition • CC151, CC152: A fault is detected in a sequence of ROM contents check of the MFPB during starting. • CC156: Upgrade of the firmware has not been successful. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the ROM version. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CC155 |
| Description: | Finisher ROM error |
| Causes: | FS control board (FSCB) |
| Error code: | CC163 |
| Description: | ROM contents error (PRT) • The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Rewrite the firmware. 2 Change PRCB 2.1. Turn OFF the power switch and replace the current PRCB with a new one. (When using a PRCB of another machine in service, be sure to use a PRCB installed in the same model.) 2.2. Update the PRCB firmware. 2.3. After completing the firmware update, turn OFF and ON the power switch and check to see that warm-up is started. 2.4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SV ERB. 3 Change SV ERB 3.1. Replace the current SV ERB with a new one. 3.2. Turn ON the power switch and check to see that warm-up is started. (One minute is spent to prepare the new SV ERB for use. During the period, the control panel backlight stays off.) 3.3. Make the specified readjustments. 4 If the above actions do not solve the problem, contact KMBT. |
| Error code: | CC164 |
| Description: | ROM contents error (MSC) • The wrong model of firmware is detected in the MFP board when the power switch is turned ON. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the corresponding board. 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CC167 |
| Description: | Finisher FW download communication fault (ENG detection) <bizhub C3851FS> A communication error is detected on the MFP board (MFPB) side during FW download communication between the MFP board (MFPB) and FS control board (FSCB). |
| Causes: | • FS control board (FSCB) • MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace FSCB. 4. Replace MFPB. |
| Error code: | CC168 |
| Description: | Finisher FW download communication fault (FNS detection) <bizhub C3851FS> A communication error is detected on the FS control board (FSCB) side during FW download communication between the MFP board (MFPB) and FS control board (FSCB). |
| Causes: | • FS control board (FSCB) • MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace FSCB. 4. Replace MFPB. |
| Error code: | CC169 |
| Description: | Finisher Flash ROM device error <bizhub C3851FS> An erase error or other device fault occurs during finisher flash ROM writing. |
| Causes: | FS control board (FSCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace FSCB. |
| Error code: | CC170 ... CC186 |
| Description: | • CC170: Dynamic link error during starting (AP0) • CC171: Dynamic link error during starting (AP1) • CC172: Dynamic link error during starting (AP2) • CC173: Dynamic link error during starting (AP3) • CC174: Dynamic link error during starting (AP4) • CC180: Dynamic link error during starting (LDR) • CC181: Dynamic link error during starting (IBR) • CC182: Dynamic link error during starting (IID) • CC183: Dynamic link error during starting (IPF) • CC184: Dynamic link error during starting (IMY) • CC185: Dynamic link error during starting (SPF) • CC186: Dynamic link error during starting (OAP) A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. If the malfunction code "CC172" has occurred, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if "Controller 1," or "Others" is set for [Image Controller Setting]. If any of these is set, select “Controller 0”. 2. If the malfunction code "CC180" has occurred, check to install the appropriate loadable device driver for an authentication unit which is installed to the MFP. When the appropriate loadable device driver is not installed, reinstall the appropriate loadable device driver. 3. Replace MFPB. 4. If the above actions do not solve the problem, contact KM. |
| Error code: | CC190 |
| Description: | Outline font load error. An error occurred while loading the outline font. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Format the hard disk. 4. Replace the hard disk. (HDD (A) / HDD (B)) 5. Replace MFPB. |
| Error code: | CC191 |
| Description: | Setting parameter load error (LDR). Upon startup, the processing of the loadable device driver setting data file failed. • RAM disk file creation failed. • Reading from the flash ROM failed. • An error occurred in API of the authentication module. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON. 2. Reinstall the loadable device driver. 3. Rewrite the firmware. 4. Replace MFPB. |
| Error code: | CC211 |
| Description: | Authentication device general error. When using the authentication device, authentication data is not to meet the specifications. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. |
| Error code: | CC212 |
| Description: | User validation error. • An error occurred while validating the user authentication information. • The loadable device driver is not successfully installed. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. When this trouble code is generated after installing the loadable device driver, check to see if there is any file other than loadable device driver in USB memory used. If there is any file, reinstall the loadable device driver. 2. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 3. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 4. Re-register the user authentication information. 5. Replace authentication device. |
| Error code: | CC213 |
| Description: | User registration error/Card information setting error. • IC card advanced settings data is not correct when starting-up the authentication device. • Authentication information data is not correct when starting-up the authentication device. • IC card advanced settings data is not correct when setting the IC card advanced settings. • Authentication information data is not correct when setting the IC card advanced settings. • IC card advanced settings data is not correct when registering the authentication information. • Authentication information data is not correct when registering the authentication information. • IC card advanced settings data is not correct when editing the authentication information. • Authentication information data is not correct when editing the authentication information. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 3. Reset the authentication settings. (card type, IC card advanced settings, and etc.) 4. Re-register the user authentication information. |
| Error code: | CC214 |
| Description: | User information deletion error. The deletion of the user information is uncompleted. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. |
| Error code: | CC216 |
| Description: | Acquisition failure of the number of trials/Initialize error of number of authentication. An error occurred during user authentication using optional authentication unit AU-102. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 3. Reset the number of authentication trials. |
| Error code: | CC301 |
| Description: | Authentication customize data error. • The master authentication customize data is corrupted upon startup. • Registration of authentication customize data in the main body has failed upon startup. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Reinstall the authentication customize data. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CC302 |
| Description: | Authentication customize data version mismatch error. The authentication customize data version is later than the firmware version of the machine. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Rewrite the main body firmware with the latest one and reinstall the authentication customize data. 2. Replace MFPB. |
| Error code: | CCC00 |
| Description: | Public user account track information error. At the first time of startup, the nonvolatile status is reset incompletely due to any trouble (such as a shut off of the main power). |
| Causes: | eMMC board (eMMC) |
| Remedy: | 1. Replace eMMC. |
| Error code: | CD002 |
| Description: | JOB RAM save error • The error in save of JOB data to the memory/ hard disk and its read error are detected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB. |
| Error code: | CD004, CD00F |
| Description: | • CD004: Storage access error (connection failure) • CD00F: Storage data transfer error • CD004: Unable to communicate between the storage and CPU board (CPUB). • CD00F: Data transfer from the storage is faulty. |
| Causes: | • Storage board (STRGB) • CPU board (CPUB) • Base board (BASEB) |
| Remedy: | 1. Check STRGB for proper installation and correct as necessary. 2. Check CPUB for proper installation and correct as necessary. 3. Replace STRGB. 4. Replace CPUB. 5. Replace BASEB. |
| Error code: | CD010 |
| Description: | Hard disk unformat. Unformatted hard disk is connected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Carry out the [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format]. 2. Replace the hard disk. (HDD (A) / HDD (B)) 3. Replace MFPB. |
| Error code: | CD011 |
| Description: | Hard disk out of specifications mounted. A hard disk that falls outside the specifications is connected. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD012 |
| Description: | Mount error due to hard disk being unformatted. • The hard disk is not logically formatted after the whole data in the hard disk has been deleted by overwriting. • The hard disk that has replaced an old one is not logically formatted. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Logically format the hard disk and then upgrade the firmware. 2. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD030 |
| Description: | Hard disk management information reading error. The machine fails to read administrative information data saved in the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Logically format the hard disk. 4. Physically format the hard disk. 5. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD041 ... CD046 |
| Description: | HDD command execution error. The error occurred inside the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD047 ... CD04B |
| Description: | HDD SCSI library error. The error occurred inside the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD050 |
| Description: | Hard disk recovery timeout. The hard disk fails to recover from the power save mode within the predetermined period of time. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Reinstall the hard disk. 4. Format the hard disk. 5. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD110 |
| Description: | Wireless LAN destination initialization error. When an initialization error occurred on the settings of the wireless LAN in the upgrade kit (UK-212/UK-215). |
| Remedy: | 1. Check the UK-212 or UK-215 connector for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Reinstall the UK-212or UK-215. |
| Error code: | CD201, CD202, CD203 |
| Description: | • CD201: File memory mounting error • CD202: Memory capacity discrepancy • CD203: Memory capacity discrepancy 2 CD201: • The file memory is not mounted. • The file has any abnormality. CD202: • File memory capacity on the MFP board (MFPB) is not enough. • File memory capacity necessary for duplex printing is not enough. CD203: File memory capacity on the MFP board (MFPB) is not enough. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Replace MFPB. |
| Error code: | CD211, CD212 |
| Description: | • CD211: PCI-SDRAM DMA operation failure • CD212: Compression/extraction timeout detection • CD211: Hardware related to the transfer of memory image of the MFP board (MFPB) fails to respond. • CD212: Hardware related to the BTC compression function of the MFP board (MFPB) fails to respond. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Replace MFPB. |
| Error code: | CD241, CD242 |
| Description: | • CD241: Encryption ASIC setting error • CD242: Encryption ASIC mounting error • CD241: Initialization error of the encrypted ASIC is detected during the machine is starting. • CD242: The faulty of the installation of encrypted ASIC is detected during the machine is starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the MFP board connector for proper connection and correct as necessary. 2. Replace MFPB |
| Error code: | CD261 |
| Description: | USB hub board failure. • When a failure is detected in USB hub board included in the local interface kit. • Non-standard USB device is connected. |
| Causes: | • MFP board (MFPB) • USB hub board (USBHB: EK-610/EK-611) |
| Remedy: | 1. Check the operation with another USB device. 2. Check the USB hub board connector for proper connection and correct as necessary. 3. Replace the USB hub board. 4. Replace MFPB. |
| Error code: | CD262 |
| Description: | Extension network adapter installation error. • When the 2nd network card settings is set to “Set” but the upgrade kit (UK-212/UK-215) is not installed. • Upgrade Kit (UK-212/UK-215) is faulty. |
| Remedy: | 1. Check the settings of [Service Mode] -> [Network Settings] -> [2nd Network Setting] -> [2nd network card settings]. 2. Check the UK-212 or UK-215 connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Reinstall the UK-212 or UK-215. |
| Error code: | CD271 |
| Description: | The memory cannot be recognized with the i-Option activated. While the i-Option is activated, the memory on an MFPB cannot be recognized. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CD272 |
| Description: | i-Option activated and HDD not installed. While the i-Option is activated, the hard disk is not installed. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) |
| Remedy: | 1. Access [Service Mode] -> [System 2] -> [HDD] and check to see if “Installed” is selected. 2. Replace the hard disk (A). 3. Replace MFPB. |
| Error code: | CD313 |
| Description: | TPM key data error. A fault occurs in the TPM key data. |
| Remedy: | 1. Touch [Recover Data] displayed at the lower right portion on the trouble screen. 2. A screen confirming whether to recover data appears. 3. Select [Yes]. 4. The screen will be shifted to the data restoration screen to perform data restoration. NOTE . When the restoration is performed in a short time, data restoration screen may not be displayed. 5. Check the message which indicates that the data restoration was successfully conducted. Turn OFF the main power switch and turn it ON again more than 10 seconds after. NOTE . In case it failed to restore data, return to the trouble code screen. 6. Replace the current MFPB with a new one. NOTE . Nonvolatile data backup will be automatically performed every hour. Backup can also be performed manually with the following setting. [Service Mode] -> [Enhanced Security] -> [Memory Data Backup] |
| Error code: | CD38E |
| Description: | Nonvolatile data save error (SPI-Flash). The "ISW download flag" saved in the SPI-Flash has an illegal value. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Rewrite the firmware. 2. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. |
| Error code: | CD390 |
| Description: | Nonvolatile data checksum error. Checksum error is detected while nonvolatile data is being checked for error by each data. (The MFP board is replaced with a new one.) |
| Remedy: | 1 Touch [Yes] on the restore screen displayed on the control panel to restore data. - - NOTE • Do not replace the printer control board and SSD board at the same time with new ones or ones removed from other machines. The backup data will be lost and image failure may be caused. |
| Error code: | CD391 |
| Description: | Nonvolatile data save error (eMMC) |
| Remedy: | NOTE • Contact the responsible people of KM before taking some countermeasures. |
| Error code: | CD392 |
| Description: | Nonvolatile data save error (EEPROM). The EEPROM is replaced with a new one. |
| Causes: | • EEPROM/1 • EEPROM/2 |
| Remedy: | 1. Replace the following components with new ones. When the transfer belt unit and the fusing unit have been replaced with new ones, perform [New Release] in the service mode. When the transfer roller has been replaced with a new one, perform [Counter clear]. • Developing unit/Y,M,C,K • Drum unit/Y,M,C,K • Toner cartridge/Y,M,C,K • Transfer belt unit • Fusing unit • Transfer roller • Feed roller, pick-up roller, separation roller (including options) 2. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 3. Set the various setting values in the service mode again. |
| Error code: | CD3C0 |
| Description: | New board detection. The board is replaced with a new one. |
| Remedy: | (2) Procedure 1. Wait until “Recover Data” appears. (MFP will reboot maximum 2 times by itself, it may take 5 minutes.) Touch the “Recover Data” button and follow the instructions that appear on the control panel to restore (backup) data. |
| Error code: | CD401 ... CD413 |
| Description: | • CD401: NACK command incorrect • CD402: ACK command incorrect • CD403: Checksum error • CD404: Receiving packet incorrect • CD405: Receiving packet analysis error • CD406: ACK receiving timeout • CD407: Retransmission timeout • CD411: Touch panel board error • CD412: Touch panel type mismatch • CD413: Electrostatic touch panel operation mode error When abnormality is found in the communication of controller. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check whether there is a strong electromagnetic noise source near the main body. 2. Check the connectors on MFPB for proper connection and correct as necessary. 3. Replace MFPB. |
| Error code: | CD601, CD602, CD603 |
| Description: | Trouble related to security. |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. If the above actions do not solve the problem, contact KM. |
| Error code: | CD701, CD702, CD703 |
| Description: | • CD701: Mechanical controller flash ROM writing error • CD702: Mechanical controller flash ROM device error • CD703: FW download communication fault CD701: A mechanical controller flash ROM writing sequence is interrupted in its mid-operation due to, for example, power being shut off. CD702: An erase error or other device fault occurs during mechanical controller flash ROM writing. CD703: • Irregular data is received during FW downloading. • Places are changed in the order of write completion pulses. • A write completion pulse is received for a memory for which binary writing is not permitted. • Final checksum mismatch in FW download • Two-minute timeout (no response from CTL, the number of transfer data items less than the specified) |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CD705, CD706 |
| Description: | • CD705: Mechanical controller sub-CPU flash ROM device error • CD706: Mechanical controller sub-CPU flash ROM error • CD705: An erase error or other device fault occurs during mechanical controller sub-CPU flash ROM writing. • CD706: A data error is determined to exist in the mechanical controller sub-CPU flash ROM during starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CDC00 |
| Description: | EEPROM fault 1. An EEPROM communication error of the main body occurs. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on the MFPB for proper connection and correct any faulty connection as necessary. 2. Replace MFPB. |
| Error code: | CDC10 |
| Description: | EEPROM fault 2. The engine serial number cannot be recovered. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on the MFPB for proper connection and correct any faulty connection as necessary. 2. Replace MFPB. |
| Error code: | CDF50, CDF70, CDFA0 |
| Description: | • CDF50: ASIC image version failure • CDF70: ASIC image access failure • CDFA0: ASIC image error Communication error is detected between the MFP board (MFPB) and the CCD board (CCDB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Check the connector between MFPB CN9-CCDB PJ3 for proper connection and correct as necessary. 2. Update the firmware. 3. Replace the CCD unit. 4. Replace MFPB. |
| Error code: | CE001 ... CE011 |
| Description: | • CE001: Abnormal message queue • CE003: Task error • CE004: Event error • CE005: Memory access error • CE006: Header access error • CE007: DIMM initialize error • CE009: Memory resource shortage error • CE011: Config. file access error at startup of FW |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CE002 |
| Description: | Message and method parameter failure. MFP board (MFPB) is faulty. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF the main power switch and turn it ON again, and conduct the following setting. [Service Mode] -> [System 1] -> [Initialization] - > [Clear All Data]. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) 4. Replace MFPB. |
| Error code: | CE101 |
| Description: | Browser finish detected. • The browser is automatically recovered (restarted) after the main body detected that the browser (separate process) has stopped with fault. • When the “Malfunction finish is detected over predetermined number of times” or “the browser task process is except in idle (printing, etc)”. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CE201 |
| Description: | Transmission operation log storage fault. When the transmission log storage failed, it repeats retrial until transmission operation log is stored. The trouble is detected when the retrial failed for predetermined number of times. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CE202 |
| Description: | PDL interpreter error. An error inside the EEPROM is detected during converting the PDL information. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format] -> [Logical Format] and perform the function. 3. Select [System 1] -> [Initialization] -> [Clear All Data] and perform the function. 4. Replace MFPB. |
| Error code: | CE203 |
| Description: | Unrecoverable error. An error does not recover even after an auto recovery. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format] -> [Logical Format] and perform the function. 3. Select [System 1] -> [Initialization] -> [Clear All Data] and perform the function. 4. Update the firmware. 5. Perform the self-diagnostic function (from main power switch ON). 6. Replace MFPB. |
| Error code: | CE301 ... CE305 |
| Description: | • CE301: Referring incorrect memory • CE302: Incorrect command • CE303: Finished due to error inside Qt library • CE304: Finished due to error outside Qt library • CE305: Program forced to stop Error occurred with the process inside the MFP controller. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. 3. Acquire the debug logs in [Service Mode] -> [Debug Settings] and analyze them. |
| Error code: | CED01 |
| Description: | The authentication application information does not exist in the hard disk/eMMC board in the enhanced server authentication state. With “Enhanced Server Authentication” set, no authentication application registration information is found in the hard disk or the eMMC board (eMMC). |
| Causes: | • eMMC board (eMMC) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF and ON the main power switch. 2. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 3. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 4. Check the connector from eMMC to MFPB for proper connection and correct as necessary. 5. Logically format the hard disk. 6. Replace the hard disk. (HDD (A) / HDD (B)) 7. If the above actions do not solve the problem, contact KM. |
| Error code: | CEEE1, CEEE3 |
| Description: | • CEEE1: MFP board (MSC) malfunction • CEEE3: MFP board (ENG) malfunction MFP board (MFPB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CEEE2 |
| Description: | Scanner section malfunction. A scanner part is faulty. |
| Causes: | • LED exposure unit • CCD board (CCDB) • Scanner drive board (SCDB) |
| Remedy: | 1. Check the connectors on CCDB or MFPB for proper connection and correct as necessary. 2. Replace SCDB 3. Replace the CCD unit. |
| Error code: | CFB00 ... CFF2D |
| Description: | Abort code |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Power switch Turn OFF and ON the power switch, and check if the Abort code appears again. NO When not reappearing, continuous use is carried out, and it is checked whether an abort code occurs. 2 Connector connection Check the connector for proper connection on MFPB and correct as necessary. NO It will correct, if connector connection has abnormalities. 3 Firmware Update the firmware to the latest version, and check if the Abort code appears again. NO After conducting firmware updating, check the firmware version No. and confirm that the firmware has been normally updated. 4 MFP board Replace MFPB |
