Konica-Minolta bizhub C658
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
200000
Скорость печати
A4
65
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Число страниц в месяц |
200 000 |
Размещение |
напольный |
Область применения |
средний офис |
Макс. формат |
A3 |
Цветность печати |
цветная |
Печать фотографий |
|
Телефон |
|
Факс |
|
Копир |
|
Тип устройства |
МФУ |
Сканер |
|
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Принтер |
|
Время разогрева |
22 |
Количество цветов |
4 |
Двусторонняя печать |
|
Прямая печать |
|
Пигментные чернила |
|
Печать без полей |
|
Макс, разрешение для ч/б печати |
|
| По Y | 1 200 |
| По X | 1 200 |
Скорость ч/б печати |
|
| A3 | 32 |
| A4 | 65 |
Время выхода первого отпечатка |
|
| Ч/б | 3 |
Копир |
|
Макс, количество копий за цикл |
9 999 |
Шаг масштабирования |
0,1 |
Время выхода первой копии |
3 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По X | 600 |
| По Y | 600 |
Сканер |
|
Устройство автоподачи оригиналов |
одностороннее |
Стандарт TWAIN |
|
Отправка изображения по e-mail |
|
Слайд-адаптер |
|
Макс. формат оригинала |
A3 |
Тип сканера |
планшетный/протяжный |
Оттенки серого |
256 |
Емкость устройства автоподачи оригиналов |
300 |
Макс, размер сканирования |
|
| По X | 297 |
Разрешение сканера |
|
| По Х | 600 |
Скорость сканирования |
|
| Цветн, | 120 |
| Ч/б | 120 |
| Цветн, | 4 |
Расходные материалы |
|
Ресурс цветного картриджа/тонера |
26 000 |
Ресурс ч/б картриджа/тонера |
28 000 |
Ресурс девелопера |
600 000 |
Ресурс фотобарабана |
135 000 |
Количество картриджей |
4 |
Печать на: |
|
| Глянцевой бумаге |
|
| Матовой бумаге |
|
| Карточках |
|
| Пленках |
|
| Этикетках |
|
| Конвертах |
|
| Фотобумаге |
|
| CD/DVD |
|
| Рулоне |
|
Плотность бумаги |
|
| Максимальная | 300 |
| Минимальная | 52 |
Факс |
|
Цветной |
|
Телефон |
|
Спикерфон |
|
Стандарт DECT |
|
Caller ID |
|
Автоответчик |
|
Проводная трубка |
|
Беспроводная трубка |
|
АОН |
|
Шрифты и языки управления |
|
Языки управления |
|
| PostScript 2 |
|
| PCL 6 |
|
| PostScript |
|
| PostScript 3 |
|
| PCL 5c |
|
|
|
|
Количество установленных шрифтов |
|
| PostScript | 137 |
| PCL | 80 |
Лотки |
|
Емкость лотка ручной подачи |
150 |
Подача бумаги |
|
| Максимальная | 6 650 |
| Стандартная | 1 150 |
Вывод бумаги |
|
| Стандартный | 250 |
| Максимальный | 3 300 |
Финишер |
|
Сортер |
|
Брошюровщик |
|
Степлер |
|
Интерфейсы |
|
Версия USB |
2,0 |
Wi-Fi |
|
FireWire (IEEE 1394) |
|
Bluetooth |
|
LPT |
|
Инфракрасный порт |
|
RS-232 |
|
Устройство для чтения карт памяти |
|
AirPrint |
|
USB |
|
Поддержка iOS |
|
Веб-интерфейс |
|
Ethernet (RJ-45) |
|
Память/Процессор |
|
Объем памяти |
4 096 |
Емкость жесткого диска |
250 |
Дополнительная информация |
|
Диагональ дисплея |
10,1 |
Экран |
|
Работа от аккумулятора |
|
Поддержка ОС |
|
| Linux |
|
| Mac OS |
|
| Windows |
|
| DOS |
|
Потребляемая мощность |
|
| При работе | 1 600 |
Габариты |
|
Ширина |
615 |
Высота |
961 |
Вес |
113 |
Глубина |
693 |
Модули
BYPASS TRAY SECTION 2
SCANNER SECTION 2
Paper Exit /Reverse Section
External Parts Section
ADF (Registration Section) 2
External Parts Section 2
High Voltage Section
Photo Conductor Section
Tray Section 2
Electrical Components Section
Tray 1 Paper Feed Section
OPERATION PANEL SECTION
ADF (External Parts Section) 2
Toner Supply Drive Section
Main Drive/ Paper Feed Drive Section
Electrical Components Section 2
ADF (CIS Section)
BYPASS TRAY SECTION
ADF (Paper Feed Section) 2
FUSING SECTION
Fusing Drive Section
ADF (External Parts Section)
Main Drive/ Paper Feed Drive Section 2
Toner Collection Section
2nd Transfer Section/Registration Section
Tray 1 Section
Tray 2 Paper Feed Section 2
Duplex Section 2
INNER COVER SECTION
Tray Section
1st Transfer Section
The Paper Cooling Fan Section
Tray 2 Section
TONER SUPPLY SECTION 2
SCANNER SECTION 3
SCANNER SECTION
Tray 1 Paper Feed Section 2
DEVELOPING SECTION
ADF (Paper Feed Section)
Duplex Section
Toner Suction Fan Section
TONER SUPPLY SECTION
2nd Transfer Section/Vertical Conveyance Section
ADF (Paper Exit Section)
Low Voltage Section
ADF (Original Glass Cleaning Section)
ADF (Paper Feed Section) 3
Paper Exit /Reverse Section 2
Vertical conveyance Section
Tray 1 Section 2
ADF (Registration Section)
Tray 2 Paper Feed Section
2nd Transfer Section/Vertical Conveyance Section 2
Duplex Section 3
ADF (CIS Cleaning Section) 2
Fusing Drive Section 2
ADF (Reading Section)
PAPER FEED SECTION
ADF (Registration Section) 3
PH Section
Scanner Section 4
ADF (CIS Cleaning Section)
Tray 2 Section 2
Детали ADF (Original Glass Cleaning Section)
| Деталь: | Brake Part |
| Парткод: | A161594500 |
| Деталь: | Regulating Plate /R |
| Парткод: | A7PU596200 |
| Деталь: | Brake Part /F |
| Парткод: | A161594600 |
| Деталь: | Regulating Plate /L |
| Парткод: | A7PU596100 |
| Деталь: | LIFTING PLATE |
| Парткод: | A7PU593000 |
| Деталь: | LEVER |
| Парткод: | A7PU595500 |
| Деталь: | Regulating Plate /R |
| Парткод: | A7PU593200 |
| Деталь: | Regulating Plate /F |
| Парткод: | A7PU593100 |
| Деталь: | LABEL |
| Парткод: | A7PU944900 |
| Деталь: | CUSHION |
| Парткод: | A161594201 |
| Деталь: | Support Holder |
| Парткод: | A161590304 |
| Деталь: | HOLD PLATE |
| Парткод: | A161591600 |
| Деталь: | Bypass Frame |
| Парткод: | A161590101 |
| Деталь: | SEAL |
| Парткод: | A161595100 |
| Деталь: | GUIDE |
| Парткод: | 4030340301 |
| Деталь: | Separating Plate |
| Парткод: | A161595300 |
| Деталь: | Slide Guide |
| Парткод: | A161595600 |
| Деталь: | HOLDER |
| Парткод: | A161595000 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030347501 |
| Деталь: | HOLD PLATE |
| Парткод: | A161595400 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161595200 |
| Деталь: | Sensor Holder |
| Парткод: | A161591800 |
| Деталь: | Harness/ Sensor |
| Парткод: | A7PUN10A00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | GUIDE |
| Парткод: | A02E597600 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4658015106 |
| Деталь: | Sensor Holder |
| Парткод: | A161591100 |
| Деталь: | TORSION SPRING |
| Парткод: | A161591000 |
| Деталь: | ACTUATOR |
| Парткод: | A161590901 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7PU596700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A161593600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7PU596000 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A161593400 |
| Деталь: | Separating Sheet |
| Парткод: | A7PU594000 |
| Деталь: | Sound shield Cushion |
| Парткод: | A79J596000 |
| Деталь: | Holding Plate |
| Парткод: | A161268300 |
| Деталь: | ORIGINAL GLASS ASSY |
| Парткод: | A161R72200 |
| Деталь: | Holding Plate |
| Парткод: | A161268200 |
| Деталь: | GUIDE |
| Парткод: | A161281600 |
| Деталь: | Scanner Wiring /1 |
| Парткод: | A161N14100 |
| Деталь: | TAPE |
| Парткод: | 4036307501 |
| Деталь: | REGULATING PLATE |
| Парткод: | A00J265300 |
| Деталь: | SEAL |
| Парткод: | 4581162501 |
| Деталь: | Lead Switch |
| Парткод: | A1UDM50200 |
| Деталь: | SEAL |
| Парткод: | A5C1263300 |
| Деталь: | SEAL |
| Парткод: | A161263000 |
| Деталь: | Scanner Wiring /2 |
| Парткод: | A161N14201 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | COVER |
| Парткод: | A161262200 |
| Деталь: | FRAME |
| Парткод: | A161261902 |
| Деталь: | FRAME |
| Парткод: | A161262002 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A161280300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A5C1280100 |
| Деталь: | Slit Glass Assy |
| Парткод: | A7PUR71100 |
| Деталь: | LEVER |
| Парткод: | A161280211 |
| Деталь: | Scanner drive board Assembly |
| Парткод: | A796H01A00 |
| Деталь: | SEAL |
| Парткод: | A161281300 |
| Деталь: | APS Photoreflector |
| Парткод: | A161M50A00 |
| Деталь: | GUIDE |
| Парткод: | A161281100 |
| Деталь: | FERRITECORE |
| Парткод: | A61FM90200 |
| Деталь: | SEAL |
| Парткод: | A5C1263400 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A5C1R90000 |
| Деталь: | HOLDER |
| Парткод: | A79J897600 |
| Деталь: | Drive Relay harness /1 |
| Парткод: | A79JN10400 |
| Деталь: | PULLEY 28T |
| Парткод: | A79J897400 |
| Деталь: | PULLEY 28T |
| Парткод: | A79J891300 |
| Деталь: | COLLAR |
| Парткод: | A79J897300 |
| Деталь: | Timing Belt 216L |
| Парткод: | A79J898400 |
| Деталь: | Pulley 33T |
| Парткод: | A79J895800 |
| Деталь: | Stepping motor |
| Парткод: | A7PUM10400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J893200 |
| Деталь: | GUIDE |
| Парткод: | A79J894000 |
| Деталь: | CUSHION |
| Парткод: | A79J896600 |
| Деталь: | GUIDE |
| Парткод: | A79J896500 |
| Деталь: | Paper exit Cover |
| Парткод: | A79J895700 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J169300 |
| Деталь: | Neutralizing Brush |
| Парткод: | A161894000 |
| Деталь: | SHEET |
| Парткод: | A161894100 |
| Деталь: | SHEET |
| Парткод: | A64J891500 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0742300 |
| Деталь: | PAPER EXIT ASSY |
| Парткод: | A79JR72500 |
| Деталь: | Timing belt 116L |
| Парткод: | A79J898300 |
| Деталь: | Cover /Upper |
| Парткод: | A7PU160100 |
| Деталь: | SEAL |
| Парткод: | A0ED163000 |
| Деталь: | Label Toner 2 |
| Парткод: | A0ED940700 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | Indicating Wiring |
| Парткод: | A161N10K00 |
| Деталь: | COVER |
| Парткод: | A161160403 |
| Деталь: | PWB Assembly LED1 |
| Парткод: | A00JH00D00 |
| Деталь: | COVER |
| Парткод: | A161160300 |
| Деталь: | Magnet /X |
| Парткод: | A0G6411200 |
| Деталь: | Open/close Cover /Front |
| Парткод: | A79J163201 |
| Деталь: | Open/close Cover /Front |
| Парткод: | A2XK163401 |
| Деталь: | Open/close Cover /Front |
| Парткод: | A79J163301 |
| Деталь: | Label (bizhub C658) |
| Парткод: | A79J940100 |
| Деталь: | Logo Mark |
| Парткод: | A00J945500 |
| Деталь: | CLEANING MATERIAL |
| Парткод: | A5C1R71600 |
| Деталь: | Support Shaft |
| Парткод: | A161165602 |
| Деталь: | Open/close Cover /Front |
| Парткод: | A79J163100 |
| Деталь: | Open/close Shaft |
| Парткод: | A2XK165000 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A2XK165700 |
| Деталь: | HINGE |
| Парткод: | A2XK163701 |
| Деталь: | Cover /Left |
| Парткод: | A79J160700 |
| Деталь: | Cover /Left |
| Парткод: | A7PU160800 |
| Деталь: | LABEL |
| Парткод: | A161940400 |
| Деталь: | CLEANING PAD |
| Парткод: | A00J106202 |
| Деталь: | Protection Cover /Upper |
| Парткод: | A782707300 |
| Деталь: | SPRING |
| Парткод: | A782570400 |
| Деталь: | Lever /1 |
| Парткод: | A782570601 |
| Деталь: | LABEL |
| Парткод: | A782940400 |
| Деталь: | Protection Cover /Lower |
| Парткод: | A782704001 |
| Деталь: | Sealing Rubber |
| Парткод: | A782703400 |
| Деталь: | Open/close Lever |
| Парткод: | A782700801 |
| Деталь: | Photoreflector |
| Парткод: | A108M50000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782704500 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A782704600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782700400 |
| Деталь: | Neutralizing Brush |
| Парткод: | A782704800 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140071 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A782565300 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | ADF Wiring /12 |
| Парткод: | A782N11100 |
| Деталь: | Actuator /3 |
| Парткод: | A782701200 |
| Деталь: | Actuator /2 |
| Парткод: | A782701100 |
| Деталь: | Actuator /1 |
| Парткод: | A782701000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782702801 |
| Деталь: | Adjusting Cushion |
| Парткод: | A782704200 |
| Деталь: | BUSHING |
| Парткод: | A782702700 |
| Деталь: | Idler Roll |
| Парткод: | A782703000 |
| Деталь: | BALL BEARING |
| Парткод: | A782704900 |
| Деталь: | Rotation Pedestal |
| Парткод: | A782701400 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A782700900 |
| Деталь: | Ground Plate /Lower |
| Парткод: | A782704700 |
| Деталь: | Scatteringprevention Plate |
| Парткод: | A782704400 |
| Деталь: | Neutralizing Brush |
| Парткод: | A782701501 |
| Деталь: | STOPPER |
| Парткод: | A108703100 |
| Деталь: | Rotation Shaft |
| Парткод: | A782702600 |
| Деталь: | WASHER |
| Парткод: | A782562400 |
| Деталь: | GROUND PLATE |
| Парткод: | A782704100 |
| Деталь: | TOP COVER ASSY |
| Парткод: | A782R70400 |
| Деталь: | FNS Relay harness |
| Парткод: | A7PUN10302 |
| Деталь: | COVER |
| Парткод: | A79J162100 |
| Деталь: | COVER |
| Парткод: | A79J163500 |
| Деталь: | LABEL |
| Парткод: | A2X0945701 |
| Деталь: | LABEL CAUTION |
| Парткод: | A7PU941701 |
| Деталь: | LABEL |
| Парткод: | A02E149900 |
| Деталь: | Label 220-240V 0.65A |
| Парткод: | A00J945201 |
| Деталь: | COVER |
| Парткод: | A00J169100 |
| Деталь: | COVER |
| Парткод: | A79J166301 |
| Деталь: | COVER |
| Парткод: | A79J168500 |
| Деталь: | SHIELD PLATE |
| Парткод: | A79J132300 |
| Деталь: | GUIDE |
| Парткод: | A79J132001 |
| Деталь: | COVER |
| Парткод: | A7PU161805 |
| Деталь: | COVER |
| Парткод: | A7PU168702 |
| Деталь: | COVER |
| Парткод: | A7PU160902 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161163900 |
| Деталь: | Cover /Right rear |
| Парткод: | A79J168400 |
| Деталь: | COVER |
| Парткод: | A161162900 |
| Деталь: | COVER |
| Парткод: | A79J162200 |
| Деталь: | COVER |
| Парткод: | A161162803 |
| Деталь: | FILTER |
| Парткод: | A79J149100 |
| Деталь: | Ventilation Part /B |
| Парткод: | A79J147201 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J132500 |
| Деталь: | CUSHION |
| Парткод: | A79JM90300 |
| Деталь: | GUIDE |
| Парткод: | A79J133001 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J132600 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A161132801 |
| Деталь: | PLATE SPRING |
| Парткод: | A79J136100 |
| Деталь: | SHEET |
| Парткод: | A79J138400 |
| Деталь: | HOLDER |
| Парткод: | A161137701 |
| Деталь: | THERMISTOR |
| Парткод: | A0P0M50300 |
| Деталь: | HV Contact Assy |
| Парткод: | A7PUR71900 |
| Деталь: | DV Contact Assy |
| Парткод: | A161R70322 |
| Деталь: | Transfer Wiring /2 |
| Парткод: | A161N11300 |
| Деталь: | Neutralizing Wiring |
| Парткод: | A161N11K00 |
| Деталь: | GUIDE |
| Парткод: | A5C1134800 |
| Деталь: | HIGH VOLTAGE UNIT |
| Парткод: | A79JM40600 |
| Деталь: | Shield Case |
| Парткод: | A64J130101 |
| Деталь: | PCB Support |
| Парткод: | V502010046 |
| Деталь: | SPACER |
| Парткод: | V502010036 |
| Деталь: | Power source /230V |
| Парткод: | A795M40B00 |
| Деталь: | Power source /100V |
| Парткод: | A8KNM40A01 |
| Деталь: | Noise filter /100V |
| Парткод: | A795M40J00 |
| Деталь: | Noise filter /230V |
| Парткод: | A79JM40H00 |
| Деталь: | Power source Wiring |
| Парткод: | A79JN10P00 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | Fixing Relay harness |
| Парткод: | A2XKN10K00 |
| Деталь: | COVER |
| Парткод: | A2X0145911 |
| Деталь: | SHIELD PLATE |
| Парткод: | A79J130200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J131700 |
| Деталь: | PWB Assembly(EXCB ASSY) |
| Парткод: | A79JH00500 |
| Деталь: | GUIDE |
| Парткод: | A64J130500 |
| Деталь: | PWB Assembly(PWB-CR ASSY) |
| Парткод: | A796H00W00 |
| Деталь: | Fixing Control harness |
| Парткод: | A64JN10800 |
| Деталь: | Relay Wiring /4 |
| Парткод: | A79JN10H00 |
| Деталь: | Insulating sheet |
| Парткод: | A79J134900 |
| Деталь: | FERRITE CORE |
| Парткод: | A3GNM71C00 |
| Деталь: | HOLDER |
| Парткод: | A161130101 |
| Деталь: | Light blocking Seal |
| Парткод: | A2XK130000 |
| Деталь: | RAIL |
| Парткод: | A161105600 |
| Деталь: | PIN |
| Парткод: | A0ED103100 |
| Деталь: | SEAL |
| Парткод: | A161107100 |
| Деталь: | GUIDE |
| Парткод: | A161138500 |
| Деталь: | Eraser (YMC) Assy |
| Парткод: | A7PUR70600 |
| Деталь: | Eraser (Black) Assy |
| Парткод: | A7PUR70500 |
| Деталь: | Light blocking Part |
| Парткод: | A161107400 |
| Деталь: | SEAL |
| Парткод: | A5C1102800 |
| Деталь: | Light blocking Part |
| Парткод: | A5C1105500 |
| Деталь: | Harness /Paperfeed |
| Парткод: | A7PUN10401 |
| Деталь: | Harness /Paperfeed |
| Парткод: | A7PUN10501 |
| Деталь: | HOLDER |
| Парткод: | A7PU627500 |
| Деталь: | HOLDER |
| Парткод: | A5C1628000 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A161M50600 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A161M50501 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4002311002 |
| Деталь: | MOTOR |
| Парткод: | 9J06M10300 |
| Деталь: | HOLDER |
| Парткод: | A5C1627101 |
| Деталь: | HOLDER |
| Парткод: | A5C1627300 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A5C1627900 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | COVER |
| Парткод: | A79J106100 |
| Деталь: | HOLDER |
| Парткод: | A79J131400 |
| Деталь: | HOLDER |
| Парткод: | A5C1137800 |
| Деталь: | Support Shaft |
| Парткод: | A7PU130800 |
| Деталь: | SHAFT |
| Парткод: | A7PU133200 |
| Деталь: | Support Shaft |
| Парткод: | A79J130800 |
| Деталь: | WtoW Connector |
| Парткод: | V651010045 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED135700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J133100 |
| Деталь: | Power source Cord /100V |
| Парткод: | A0EDN30002 |
| Деталь: | AC Wiring /100V |
| Парткод: | A79JN10A01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J136000 |
| Деталь: | COVER |
| Парткод: | A79J139000 |
| Деталь: | Power source Cord /120V |
| Парткод: | A0P0N30000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J133200 |
| Деталь: | AC Wiring /120V |
| Парткод: | A79JN10M01 |
| Деталь: | AC Wiring /230V |
| Парткод: | A79JN10N00 |
| Деталь: | CUSHION |
| Парткод: | A79JM90200 |
| Деталь: | Power Supply Wiring |
| Парткод: | A02EN12513 |
| Деталь: | SHEET |
| Парткод: | A79J139600 |
| Деталь: | SHEET |
| Парткод: | A79J139700 |
| Деталь: | LABEL |
| Парткод: | 9J06730101 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A161566000 |
| Деталь: | ROLLER |
| Парткод: | 4034352501 |
| Деталь: | GROUND PLATE |
| Парткод: | A5C1560600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161560900 |
| Деталь: | Photoreflector |
| Парткод: | A0EDM50100 |
| Деталь: | SHAFT |
| Парткод: | A5C1565500 |
| Деталь: | ACTUATOR |
| Парткод: | A161561600 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Paper feed Frame |
| Парткод: | A161565302 |
| Деталь: | Frame /Front |
| Парткод: | A161560112 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A161562800 |
| Деталь: | BUSHING |
| Парткод: | 4131300301 |
| Деталь: | GEAR 26T |
| Парткод: | A161562400 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A64J564101 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A64J564201 |
| Деталь: | CLUTCH |
| Парткод: | A02E561100 |
| Деталь: | GEAR 34T |
| Парткод: | A161562300 |
| Деталь: | GEAR 28T |
| Парткод: | A161562600 |
| Деталь: | SHAFT |
| Парткод: | A161562000 |
| Деталь: | BUSHING |
| Парткод: | A161562500 |
| Деталь: | HOLDER |
| Парткод: | A161562101 |
| Деталь: | TORSION SPRING |
| Парткод: | A161567400 |
| Деталь: | LEVER |
| Парткод: | A161567300 |
| Деталь: | SHAFT |
| Парткод: | A02E560800 |
| Деталь: | Caulking(Frame) |
| Парткод: | A161F56027 |
| Деталь: | GEAR 24T |
| Парткод: | A79J576400 |
| Деталь: | Paperfeed Relay harness |
| Парткод: | A79JN10800 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | SHAFT |
| Парткод: | A161560500 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A79JM70002 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A79JM70102 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A79JM70202 |
| Деталь: | COVER |
| Парткод: | A161190903 |
| Деталь: | COVER |
| Парткод: | A79J162600 |
| Деталь: | COVER |
| Парткод: | A79J161501 |
| Деталь: | SEAL |
| Парткод: | A7PU168500 |
| Деталь: | SEAL |
| Парткод: | A7PU168600 |
| Деталь: | Connecting Shaft |
| Парткод: | A7PU138200 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A79J138101 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7PU138301 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7PU138002 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J121600 |
| Деталь: | SPEAKER ASSY |
| Парткод: | A79JR72600 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A7PUN15300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J164100 |
| Деталь: | Support Plate |
| Парткод: | A7PU135402 |
| Деталь: | COVER |
| Парткод: | A79J161900 |
| Деталь: | COVER |
| Парткод: | A00J169100 |
| Деталь: | SEAL |
| Парткод: | A161162400 |
| Деталь: | COVER |
| Парткод: | A7PU161400 |
| Деталь: | PWB Assembly(PWB-LED ASSY) |
| Парткод: | A161H00U01 |
| Деталь: | Mountig Plate Panel Assy |
| Парткод: | A79JR71300 |
| Деталь: | Light blocking Cover |
| Парткод: | A79J167800 |
| Деталь: | LENS |
| Парткод: | A161167000 |
| Деталь: | Label Emperon |
| Парткод: | A011946200 |
| Деталь: | COVER |
| Парткод: | A79J161701 |
| Деталь: | Light blocking Sheet /2 |
| Парткод: | A161167400 |
| Деталь: | Light blocking Sheet /1 |
| Парткод: | A161167300 |
| Деталь: | LENS |
| Парткод: | A161167100 |
| Деталь: | Indicating Wiring/3 |
| Парткод: | A5C1N10B00 |
| Деталь: | InIndicating Wiring/4 |
| Парткод: | A5C1N10D00 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A79JN15600 |
| Деталь: | FERRITECORE |
| Парткод: | A5C1M92000 |
| Деталь: | Wiring Guide /2 |
| Парткод: | A782130301 |
| Деталь: | WASHER |
| Парткод: | A782117000 |
| Деталь: | CUSHION |
| Парткод: | A782105101 |
| Деталь: | CUSHION |
| Парткод: | A782105001 |
| Деталь: | Guide Film |
| Парткод: | A782117100 |
| Деталь: | STOPPER SHAFT |
| Парткод: | A782101500 |
| Деталь: | Auxiliary Plate /1 |
| Парткод: | A782891001 |
| Деталь: | Ground Plate spring /1 |
| Парткод: | A782111000 |
| Деталь: | Ground Plate spring /2 |
| Парткод: | A782111100 |
| Деталь: | Guide Sheet |
| Парткод: | A782101700 |
| Деталь: | ROLL |
| Парткод: | A782262800 |
| Деталь: | SHAFT |
| Парткод: | A782264900 |
| Деталь: | ADF Wiring /19 |
| Парткод: | A782N11800 |
| Деталь: | GUIDE |
| Парткод: | A782111200 |
| Деталь: | GUIDE |
| Парткод: | A79J241601 |
| Деталь: | Stepping motor |
| Парткод: | A7PUM10600 |
| Деталь: | Stepping motor |
| Парткод: | A7PUM10700 |
| Деталь: | HOLDER |
| Парткод: | A79J240100 |
| Деталь: | GEAR 25T |
| Парткод: | A79J240500 |
| Деталь: | Gear 91T/28T |
| Парткод: | A79J240300 |
| Деталь: | Gear 65T |
| Парткод: | A161240600 |
| Деталь: | Gear 52T/29T |
| Парткод: | A79J240400 |
| Деталь: | SPRING |
| Парткод: | A79J241700 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038541202 |
| Деталь: | JOINT |
| Парткод: | A161240700 |
| Деталь: | Gear 20/42T |
| Парткод: | A161240900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J241500 |
| Деталь: | Gear 31T |
| Парткод: | A161241000 |
| Деталь: | SHAFT |
| Парткод: | A161241200 |
| Деталь: | Gear17T |
| Парткод: | A161241400 |
| Деталь: | TB Drive Assy |
| Парткод: | A79JR71500 |
| Деталь: | Drive Relay harness /2 |
| Парткод: | A79JN10500 |
| Деталь: | Gear 22/55T |
| Парткод: | A64J222200 |
| Деталь: | Belt 214L |
| Парткод: | A64J222400 |
| Деталь: | WASHER |
| Парткод: | A64J222500 |
| Деталь: | Cauking(Hold Plate) |
| Парткод: | A64JR7A000 |
| Деталь: | HB Stepping motor |
| Парткод: | A61DM10000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J254200 |
| Деталь: | Stepping motor |
| Парткод: | A2X0M10000 |
| Деталь: | PAPER FEED DRIVE ASSY |
| Парткод: | A79JR70200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J221400 |
| Деталь: | HB Stepping motor |
| Парткод: | A796M10500 |
| Деталь: | GEAR 20T |
| Парткод: | A64J257800 |
| Деталь: | GEAR 22T |
| Парткод: | A79J254000 |
| Деталь: | Flapper solenoid |
| Парткод: | A161M20300 |
| Деталь: | GUIDE |
| Парткод: | A79J216100 |
| Деталь: | DC Brushless motor /40 |
| Парткод: | A79JM10400 |
| Деталь: | DC Brushless motor /40 |
| Парткод: | A79JM11400 |
| Деталь: | GUIDE |
| Парткод: | A79J134701 |
| Деталь: | Spacer /A |
| Парткод: | A1RF517100 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A79JR70300 |
| Деталь: | Vertical conveyance Drive Assy |
| Парткод: | A64JR70600 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A161105500 |
| Деталь: | SHEET |
| Парткод: | A79J134500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J131901 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A4MG130900 |
| Деталь: | PWB Assembly(PWB-DS) |
| Парткод: | A79JH02A01 |
| Деталь: | EEPROM (2 pieces) |
| Парткод: | V864800107 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A79J134200 |
| Деталь: | Ground Plate spring |
| Парткод: | A7PU134800 |
| Деталь: | Support Rubber |
| Парткод: | A4EU138000 |
| Деталь: | PWB Assembly (PWB-MFP) |
| Парткод: | A79JH02102 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J130900 |
| Деталь: | HDD |
| Парткод: | A2X0M72C00 |
| Деталь: | COVER |
| Парткод: | A7PU134700 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A79JN15100 |
| Деталь: | Power source Cable |
| Парткод: | A161N15J00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J131100 |
| Деталь: | Harness /Relay |
| Парткод: | A7PUN10800 |
| Деталь: | DUCT |
| Парткод: | A7PU140100 |
| Деталь: | FAN MOTOR |
| Парткод: | A0EDM10500 |
| Деталь: | GUIDE |
| Парткод: | A7PU130400 |
| Деталь: | Harness /Fax relay |
| Парткод: | A7PUN10700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J131600 |
| Деталь: | CONNECTOR |
| Парткод: | V651010025 |
| Деталь: | COVER |
| Парткод: | A7PU139800 |
| Деталь: | Connector Cover |
| Парткод: | V503010002 |
| Деталь: | SCREW |
| Парткод: | A161137900 |
| Деталь: | FERRITECORE |
| Парткод: | A61FM90200 |
| Деталь: | GASKET |
| Парткод: | A79JM90600 |
| Деталь: | GASKET |
| Парткод: | A79JM90700 |
| Деталь: | TAPE |
| Парткод: | A0P0264800 |
| Деталь: | Grounding Wire /3 |
| Парткод: | A1DMN13700 |
| Деталь: | FERRITECORE |
| Парткод: | A0G6M93100 |
| Деталь: | FERRITECORE |
| Парткод: | A3EWM90300 |
| Деталь: | Drive Wiring /2 |
| Парткод: | A9DVN10000 |
| Деталь: | CIS ASSY |
| Парткод: | A782R70200 |
| Деталь: | ADF Wiring /10 |
| Парткод: | A782N10900 |
| Деталь: | Wiring Cover |
| Парткод: | A782116301 |
| Деталь: | PWB Assembly(PWB-DC Assy) |
| Парткод: | A3CKH00200 |
| Деталь: | PLATE |
| Парткод: | A782116201 |
| Деталь: | ADF cable |
| Парткод: | A782N12001 |
| Деталь: | ADF Wiring /40 |
| Парткод: | A782N12200 |
| Деталь: | Wiring Cover /A |
| Парткод: | A161592800 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A5C1591900 |
| Деталь: | Paperfeed Drive harness /1 |
| Парткод: | A161N12200 |
| Деталь: | Paper feed Frame |
| Парткод: | A161590201 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A161594100 |
| Деталь: | Guide Sheet |
| Парткод: | A161594700 |
| Деталь: | Auxiliary Guide |
| Парткод: | A161591700 |
| Деталь: | BUSHING |
| Парткод: | A02E596300 |
| Деталь: | ROLLER |
| Парткод: | A00F623201 |
| Деталь: | Slide Stopper |
| Парткод: | A161594400 |
| Деталь: | Paper feed Shaft |
| Парткод: | A161591500 |
| Деталь: | Drive Shaft |
| Парткод: | A161591400 |
| Деталь: | Paper feed Cam |
| Парткод: | A161593300 |
| Деталь: | Caulking(Mounting Plate Drive Frame ) |
| Парткод: | A161F59002 |
| Деталь: | GEAR 22T |
| Парткод: | A02E595400 |
| Деталь: | BUSHING |
| Парткод: | 4131353202 |
| Деталь: | Bypass Gear 24T |
| Парткод: | A161590800 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A161590600 |
| Деталь: | GEAR 30T |
| Парткод: | A02E596100 |
| Деталь: | CLUTCH ASSY |
| Парткод: | A02E595100 |
| Деталь: | CLUTCH |
| Парткод: | A02EM20100 |
| Деталь: | COVER |
| Парткод: | A0ED597800 |
| Деталь: | SOLENOID |
| Парткод: | 9321240011 |
| Деталь: | Light blocking Plate |
| Парткод: | A79J591300 |
| Деталь: | Drive Cover |
| Парткод: | A5C1591200 |
| Деталь: | Hold Claw |
| Парткод: | A161594800 |
| Деталь: | Coil spring |
| Парткод: | A161594900 |
| Деталь: | Bypass Tray Assy |
| Парткод: | A79JR71900 |
| Деталь: | Bypass Tray Assy |
| Парткод: | A79JR72000 |
| Деталь: | Auxiliary Cover |
| Парткод: | A7PU596900 |
| Деталь: | Sound shield Plate |
| Парткод: | A79J701600 |
| Деталь: | Sound shield Plate |
| Парткод: | A79J701700 |
| Деталь: | Label Paper supply |
| Парткод: | A7PU944401 |
| Деталь: | Auxiliary Tray |
| Парткод: | A161592200 |
| Деталь: | Bypass Tray /Upper |
| Парткод: | A7PU592100 |
| Деталь: | Label Paper supply |
| Парткод: | A7PU944301 |
| Деталь: | Label Metric |
| Парткод: | A7PU944100 |
| Деталь: | Label Inch |
| Парткод: | A7PU944200 |
| Деталь: | ACTUATOR |
| Парткод: | A161592400 |
| Деталь: | TORSION SPRING |
| Парткод: | A161592501 |
| Деталь: | Holding Cover /2 |
| Парткод: | A161592600 |
| Деталь: | Holding Cover |
| Парткод: | A161592300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7PUF60000 |
| Деталь: | GEAR |
| Парткод: | A7PU593500 |
| Деталь: | Bypass Tray |
| Парткод: | A7PU592000 |
| Деталь: | VR |
| Парткод: | A161M50400 |
| Деталь: | FRICTION PLATE |
| Парткод: | A161593800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7PU593700 |
| Деталь: | Harness/ Relay |
| Парткод: | A7PUN10900 |
| Деталь: | Regulating Gear 41T |
| Парткод: | A161594300 |
| Деталь: | Harness/ Sensor |
| Парткод: | A7PUN10B01 |
| Деталь: | Insulating sheet |
| Парткод: | A7PU599300 |
| Деталь: | Sound shield Plate |
| Парткод: | A79J596200 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A782560501 |
| Деталь: | Regulating Plate /Front |
| Парткод: | A782560401 |
| Деталь: | LIFTING PLATE |
| Парткод: | A782561703 |
| Деталь: | Arm /1 |
| Парткод: | A782600101 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Arm /2 |
| Парткод: | A782601500 |
| Деталь: | Photoreflector |
| Парткод: | A108M50000 |
| Деталь: | RACK |
| Парткод: | A782562001 |
| Деталь: | GEAR 40T |
| Парткод: | A782600900 |
| Деталь: | VR |
| Парткод: | A1UDM50100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782562600 |
| Деталь: | TRAY |
| Парткод: | A782561103 |
| Деталь: | BUSHING |
| Парткод: | A161210200 |
| Деталь: | Paper exit Spring /6 |
| Парткод: | A782891901 |
| Деталь: | ACTUATOR |
| Парткод: | A782891800 |
| Деталь: | Gear /7 34T |
| Парткод: | A782568500 |
| Деталь: | WASHER |
| Парткод: | A782562400 |
| Деталь: | Torsion Coil spring /A |
| Парткод: | A782573601 |
| Деталь: | LEVER |
| Парткод: | A782566800 |
| Деталь: | SHAFT |
| Парткод: | A782566900 |
| Деталь: | ADF Wiring /4 |
| Парткод: | A782N10300 |
| Деталь: | FRICTION PLATE |
| Парткод: | A782561000 |
| Деталь: | ADF Wiring /5 |
| Парткод: | A782N10400 |
| Деталь: | LIFTING PLATE ASSY |
| Парткод: | A782R70311 |
| Деталь: | Wiring Guide |
| Парткод: | A2XK130601 |
| Деталь: | DUCT |
| Парткод: | A79J140200 |
| Деталь: | FAN MOTOR |
| Парткод: | 4556M10000 |
| Деталь: | DUCT |
| Парткод: | A79J140100 |
| Деталь: | CUSHION |
| Парткод: | A79J103201 |
| Деталь: | CUSHION |
| Парткод: | A79J103301 |
| Деталь: | CUSHION |
| Парткод: | A79J754700 |
| Деталь: | CUSHION |
| Парткод: | A79J754600 |
| Деталь: | SEAL |
| Парткод: | A79J102700 |
| Деталь: | CUSHION |
| Парткод: | A79J754400 |
| Деталь: | CUSHION |
| Парткод: | A79J754500 |
| Деталь: | SHEET |
| Парткод: | A79J138300 |
| Деталь: | Temp. transfer |
| Парткод: | A796M50000 |
| Деталь: | Protection Plate |
| Парткод: | A2XK138200 |
| Деталь: | HOLDER |
| Парткод: | A2XK138100 |
| Деталь: | CUSHION |
| Парткод: | A79J754100 |
| Деталь: | CUSHION |
| Парткод: | A79J754000 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A2XK754200 |
| Деталь: | Fixing Coil/100V-120V |
| Парткод: | A79JM40C00 |
| Деталь: | Fixing Coil/230V |
| Парткод: | A79JM40D00 |
| Деталь: | CUSHION |
| Парткод: | A79J754200 |
| Деталь: | CUSHION |
| Парткод: | A79J754300 |
| Деталь: | FUSING UNIT |
| Парткод: | A79JR71000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J123102 |
| Деталь: | CUSHION |
| Парткод: | A79J144700 |
| Деталь: | CUSHION |
| Парткод: | A79J144500 |
| Деталь: | CUSHION |
| Парткод: | A79J144400 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313130051 |
| Деталь: | DUCT |
| Парткод: | A79J144102 |
| Деталь: | CUSHION |
| Парткод: | A79J144600 |
| Деталь: | DUCT |
| Парткод: | A79J144201 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J144301 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A2XK130801 |
| Деталь: | Temperature Relay harness |
| Парткод: | A2XKN10700 |
| Деталь: | Gear 18/62T |
| Парткод: | A2XK254200 |
| Деталь: | Gear 18/57T |
| Парткод: | A161254300 |
| Деталь: | Gear 55T/33T |
| Парткод: | A79J254400 |
| Деталь: | BUSHING |
| Парткод: | A161254700 |
| Деталь: | GEAR 38T |
| Парткод: | A161254500 |
| Деталь: | BUSHING |
| Парткод: | A161232200 |
| Деталь: | Gear 22/22T |
| Парткод: | A2XK228800 |
| Деталь: | Slide Shaft Holder |
| Парткод: | A03U812800 |
| Деталь: | SHAFT |
| Парткод: | A161256300 |
| Деталь: | Frame /ASSY |
| Парткод: | A79J231001 |
| Деталь: | BUSHING |
| Парткод: | A0ED259700 |
| Деталь: | SHAFT |
| Парткод: | A161259400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161258800 |
| Деталь: | GEAR 26T |
| Парткод: | A0ED257500 |
| Деталь: | GEAR 16T |
| Парткод: | 4038258001 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161232501 |
| Деталь: | BUSHING |
| Парткод: | A161232300 |
| Деталь: | Gear16T |
| Парткод: | A79J231300 |
| Деталь: | Gear18T |
| Парткод: | A161230700 |
| Деталь: | COLLAR |
| Парткод: | A79J897300 |
| Деталь: | COLLAR |
| Парткод: | A161232401 |
| Деталь: | GEAR 12T |
| Парткод: | A161122002 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J122400 |
| Деталь: | GEAR 17T |
| Парткод: | A161121900 |
| Деталь: | Label M4 |
| Парткод: | A161941100 |
| Деталь: | Gear16T |
| Парткод: | A161228701 |
| Деталь: | GEAR |
| Парткод: | A161254600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J231100 |
| Деталь: | STOPPER |
| Парткод: | A79J120900 |
| Деталь: | Fusing Drive Assy |
| Парткод: | A79JR71600 |
| Деталь: | Protection Cover /Rear |
| Парткод: | A782160001 |
| Деталь: | Wiring Guide /1 |
| Парткод: | A782130001 |
| Деталь: | Wiring Guide /3 |
| Парткод: | A782130600 |
| Деталь: | ADF Wiring /1 |
| Парткод: | A782N10000 |
| Деталь: | Sheet /Left |
| Парткод: | A782113900 |
| Деталь: | DFCB ASSY |
| Парткод: | A782H00104 |
| Деталь: | Sheet /Right |
| Парткод: | A782114000 |
| Деталь: | ADF Wiring /13 |
| Парткод: | A782N11200 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 9J07210802 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 9J07210901 |
| Деталь: | Hinge /Right |
| Парткод: | A782113801 |
| Деталь: | BASE FRAME |
| Парткод: | A782110006 |
| Деталь: | Label /1 |
| Парткод: | A782940100 |
| Деталь: | MAGNET |
| Парткод: | 9J07160200 |
| Деталь: | Sound shield Cushion /2 |
| Парткод: | A782160300 |
| Деталь: | Sound shield Cushion /1 |
| Парткод: | A782160200 |
| Деталь: | Protection Cover /Front |
| Парткод: | A782160100 |
| Деталь: | Holding Mat /1 |
| Парткод: | A782112301 |
| Деталь: | REINFORCE PLATE /1 |
| Парткод: | A782110600 |
| Деталь: | Seal /Rear |
| Парткод: | A782119300 |
| Деталь: | Hinge /Left |
| Парткод: | A782113701 |
| Деталь: | REINFORCE PLATE /2 |
| Парткод: | A782117500 |
| Деталь: | CUSHION |
| Парткод: | A782117600 |
| Деталь: | ADF ASSY |
| Парткод: | A782R70022 |
| Деталь: | FERRITECORE |
| Парткод: | A3EWM90300 |
| Деталь: | HOLDER |
| Парткод: | A79J220900 |
| Деталь: | Gear19T |
| Парткод: | A79J259800 |
| Деталь: | GEAR 29T |
| Парткод: | A79J253300 |
| Деталь: | COLLAR |
| Парткод: | A79J897300 |
| Деталь: | TIMING BELT 180L |
| Парткод: | A79J226600 |
| Деталь: | Gear 23T |
| Парткод: | A79J226200 |
| Деталь: | GEAR 32T |
| Парткод: | A79J226301 |
| Деталь: | GEAR 30T |
| Парткод: | A79J226400 |
| Деталь: | SHAFT |
| Парткод: | A79J223100 |
| Деталь: | Pulley 44T |
| Парткод: | A79J220000 |
| Деталь: | Timing belt 112L |
| Парткод: | A79J226500 |
| Деталь: | Timing belt 126L |
| Парткод: | A79J226700 |
| Деталь: | BUSHING |
| Парткод: | A161210200 |
| Деталь: | Frame /ASSY |
| Парткод: | A79J221200 |
| Деталь: | HB Stepping motor |
| Парткод: | A61DM10000 |
| Деталь: | Timing belt 156L |
| Парткод: | A79J226800 |
| Деталь: | GEAR 28T |
| Парткод: | A79J220700 |
| Деталь: | Pulley 24T |
| Парткод: | A79J253000 |
| Деталь: | Pulley 24T |
| Парткод: | A79J222500 |
| Деталь: | HOLDER |
| Парткод: | A79J220800 |
| Деталь: | SHUTTER |
| Парткод: | A64J363700 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED363200 |
| Деталь: | SEAL |
| Парткод: | A0ED363400 |
| Деталь: | PIPE |
| Парткод: | A0ED363001 |
| Деталь: | SEAL |
| Парткод: | A0ED363312 |
| Деталь: | Gear 14T/17T |
| Парткод: | A79J245100 |
| Деталь: | Gear 20T/8T |
| Парткод: | A79J245000 |
| Деталь: | Gear 62T/16T |
| Парткод: | A79J245400 |
| Деталь: | Waste Toner Box |
| Парткод: | A4NNWY1 |
| Деталь: | Waste Toner Box |
| Парткод: | A4NNWY3 |
| Деталь: | WASTE TONER DRIVE ASSY |
| Парткод: | A79JR71400 |
| Деталь: | COVER |
| Парткод: | A161362000 |
| Деталь: | Waste Toner Pipe |
| Парткод: | A64JR71400 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A161700901 |
| Деталь: | Photo sensing |
| Парткод: | A161M50000 |
| Деталь: | Photo sensing |
| Парткод: | A161M50300 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4011585202 |
| Деталь: | Protection Sheet |
| Парткод: | A161701800 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A7AHM50400 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Conveyance Wiring |
| Парткод: | A79JN10900 |
| Деталь: | Sensor Relay harness /1 |
| Парткод: | A79JN10600 |
| Деталь: | CONVEYANCE SOLENOID |
| Парткод: | A034M20100 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | Arm /1 |
| Парткод: | A161700401 |
| Деталь: | Arm /2 |
| Парткод: | A161700700 |
| Деталь: | Mounting Plate /B |
| Парткод: | A161700301 |
| Деталь: | Spring /A |
| Парткод: | A161701100 |
| Деталь: | Cushion /C |
| Парткод: | A161702101 |
| Деталь: | Actuator /T |
| Парткод: | A161701703 |
| Деталь: | GROUND PLATE |
| Парткод: | A79J701200 |
| Деталь: | CONTACT |
| Парткод: | A79J701300 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7PU701000 |
| Деталь: | GEAR 22T |
| Парткод: | A79J709000 |
| Деталь: | Conveyance Spring /A |
| Парткод: | A161702000 |
| Деталь: | BUSHING |
| Парткод: | A161702200 |
| Деталь: | Seal /A |
| Парткод: | A161701900 |
| Деталь: | COVER |
| Парткод: | A0ED705800 |
| Деталь: | Pulling Spring |
| Парткод: | A0ED702800 |
| Деталь: | Holding Shutter |
| Парткод: | A161706001 |
| Деталь: | Guide Sheet /A |
| Парткод: | A161701301 |
| Деталь: | PLATE SPRING |
| Парткод: | A7PU701100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A7PU701200 |
| Деталь: | Guide Sheet |
| Парткод: | A79J700500 |
| Деталь: | Guide Sheet |
| Парткод: | A79J700800 |
| Деталь: | Photoreflector |
| Парткод: | A0EDM50100 |
| Деталь: | ROLLER |
| Парткод: | A0ED700200 |
| Деталь: | ROLLER |
| Парткод: | A5C1700101 |
| Деталь: | Guide Sheet |
| Парткод: | A79J700900 |
| Деталь: | GUIDE |
| Парткод: | 4038353901 |
| Деталь: | Guide Sheet |
| Парткод: | A79J701000 |
| Деталь: | Guide Plate /Middle |
| Парткод: | A79J700300 |
| Деталь: | Label M2 |
| Парткод: | A161946300 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A79J700400 |
| Деталь: | Ground Plate /D |
| Парткод: | A5C1700800 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A5C1703200 |
| Деталь: | FIXED POWER RESISTORS |
| Парткод: | V800500300 |
| Деталь: | GEAR 20T |
| Парткод: | A0ED700300 |
| Деталь: | GEAR 14T |
| Парткод: | A0ED700700 |
| Деталь: | Guide Plate /Inside |
| Парткод: | A79J700100 |
| Деталь: | Sensor Wiring /3 |
| Парткод: | A161N12H00 |
| Деталь: | GROUND PLATE |
| Парткод: | A161622100 |
| Деталь: | SHEET |
| Парткод: | A161626200 |
| Деталь: | ROLL |
| Парткод: | A161623400 |
| Деталь: | Reinforce Plate /Right |
| Парткод: | A79J623100 |
| Деталь: | Protection Sheet |
| Парткод: | A55V624700 |
| Деталь: | Reinforce Plate /Left |
| Парткод: | A161623301 |
| Деталь: | LABEL |
| Парткод: | A795942401 |
| Деталь: | HOLDER |
| Парткод: | A5C1624300 |
| Деталь: | LEVER |
| Парткод: | A161626502 |
| Деталь: | LEVER |
| Парткод: | A161626602 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161626800 |
| Деталь: | LENS |
| Парткод: | A161626000 |
| Деталь: | Light blocking Sheet |
| Парткод: | A161626100 |
| Деталь: | Label 1 |
| Парткод: | A161943100 |
| Деталь: | COVER |
| Парткод: | A5C1625001 |
| Деталь: | COVER |
| Парткод: | A161625900 |
| Деталь: | HANDLE |
| Парткод: | A161626900 |
| Деталь: | COVER |
| Парткод: | A161625114 |
| Деталь: | CUSHION |
| Парткод: | A5C1628500 |
| Деталь: | 1 st Cassette Assy |
| Парткод: | A79JR72100 |
| Деталь: | Label Cd |
| Парткод: | A79J941500 |
| Деталь: | Label FD |
| Парткод: | A79J941200 |
| Деталь: | Label FD |
| Парткод: | A79J941300 |
| Деталь: | HOLDER |
| Парткод: | A5C1563100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161568800 |
| Деталь: | SPACER |
| Парткод: | 4040561000 |
| Деталь: | GUIDE |
| Парткод: | A5C1563500 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A0ED563900 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A64J564101 |
| Деталь: | SHEET |
| Парткод: | A5C1565600 |
| Деталь: | GUIDE PLATE |
| Парткод: | A7PU578400 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161568700 |
| Деталь: | SHAFT |
| Парткод: | A5C1563400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161564001 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030301703 |
| Деталь: | SHAFT |
| Парткод: | A161563300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161563901 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4532341001 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161564400 |
| Деталь: | SPACER |
| Парткод: | A161564200 |
| Деталь: | LEVER |
| Парткод: | A5C1564101 |
| Деталь: | SPACER |
| Парткод: | A161564300 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A64JR71100 |
| Деталь: | GUIDE |
| Парткод: | A7PU577700 |
| Деталь: | GUIDE |
| Парткод: | A7PU577600 |
| Деталь: | GUIDE |
| Парткод: | A7PU577500 |
| Деталь: | DUCT |
| Парткод: | A79J830100 |
| Деталь: | CUSHION |
| Парткод: | A79J831300 |
| Деталь: | CUSHION |
| Парткод: | A79J831200 |
| Деталь: | DUCT |
| Парткод: | A79J830300 |
| Деталь: | COVER |
| Парткод: | A79J830700 |
| Деталь: | CUSHION |
| Парткод: | A79J831700 |
| Деталь: | DUCT |
| Парткод: | A79J830200 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A79J832000 |
| Деталь: | WASHER |
| Парткод: | A79J832400 |
| Деталь: | Support Rubber |
| Парткод: | A79J832100 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313100072 |
| Деталь: | SEAL |
| Парткод: | A79J832300 |
| Деталь: | CUSHION |
| Парткод: | A79J831000 |
| Деталь: | HOLDER |
| Парткод: | A79J830001 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J832200 |
| Деталь: | Fixing Claw |
| Парткод: | A79J165700 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | A79JR71200 |
| Деталь: | LABEL |
| Парткод: | A161943000 |
| Деталь: | Cover /Front |
| Парткод: | A79J165000 |
| Деталь: | PROTECTION PART |
| Парткод: | A161165300 |
| Деталь: | BAND |
| Парткод: | A0ED162401 |
| Деталь: | Label DR/K |
| Парткод: | A161942500 |
| Деталь: | Label DR/C |
| Парткод: | A161942400 |
| Деталь: | LABEL |
| Парткод: | A79J942600 |
| Деталь: | Label DR/M |
| Парткод: | A161942300 |
| Деталь: | Label DR/Y |
| Парткод: | A161942200 |
| Деталь: | LABEL |
| Парткод: | A79J942100 |
| Деталь: | LABEL |
| Парткод: | A161942000 |
| Деталь: | SEESAW-SWITCH |
| Парткод: | 4038M60000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161135100 |
| Деталь: | AC Wiring /B |
| Парткод: | A2XKN10C00 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06M60100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038228702 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161151300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161151100 |
| Деталь: | SEAL |
| Парткод: | A7PU168800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161135504 |
| Деталь: | STOPPER |
| Парткод: | 4470402401 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | LABEL |
| Парткод: | A2X0949100 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038101401 |
| Деталь: | SEAL |
| Парткод: | A5C1404500 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161104300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A7PU102201 |
| Деталь: | SHAFT |
| Парткод: | A161104200 |
| Деталь: | LEVER |
| Парткод: | A161101900 |
| Деталь: | STOPPER |
| Парткод: | A7PU102301 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A5C1104800 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996305501 |
| Деталь: | Rail /ASSY |
| Парткод: | A5C1101101 |
| Деталь: | Shoulder screw /2 |
| Парткод: | A1UD192400 |
| Деталь: | ROLL |
| Парткод: | A161103901 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A5C1104400 |
| Деталь: | COVER |
| Парткод: | A161103700 |
| Деталь: | ROLL |
| Парткод: | A161623400 |
| Деталь: | SHAFT |
| Парткод: | A161105200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161101600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161101701 |
| Деталь: | HOLDER |
| Парткод: | A7PU104000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A5C1104700 |
| Деталь: | HOLDER |
| Парткод: | A5C1106000 |
| Деталь: | Intermediate Image Transfer Kit |
| Парткод: | A79JR70911 |
| Деталь: | GUIDE |
| Парткод: | A79J508400 |
| Деталь: | Lock Part |
| Парткод: | A161110601 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED111000 |
| Деталь: | Lever /Front |
| Парткод: | A161112500 |
| Деталь: | Arm /Front |
| Парткод: | A5C1112800 |
| Деталь: | Fusing Rail /Front |
| Парткод: | A161110400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161112200 |
| Деталь: | Adjusting Plate |
| Парткод: | A161112600 |
| Деталь: | RAIL |
| Парткод: | A161110202 |
| Деталь: | RAIL |
| Парткод: | A79J110300 |
| Деталь: | Contact /Color |
| Парткод: | A0ED111500 |
| Деталь: | CONTACT |
| Парткод: | A161112000 |
| Деталь: | CONTACT |
| Парткод: | A0ED112000 |
| Деталь: | DETECTING PLATE |
| Парткод: | A161110500 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED110900 |
| Деталь: | CONTACT |
| Парткод: | A0ED111700 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | Arm /Rear |
| Парткод: | A5C1112900 |
| Деталь: | CONTACT |
| Парткод: | A161112300 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A5C1R90000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A5C1112101 |
| Деталь: | Connecting Detection harness |
| Парткод: | A161N10J00 |
| Деталь: | Transfer Wiring /1 |
| Парткод: | A161N11200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161112700 |
| Деталь: | CONTACT |
| Парткод: | A161112400 |
| Деталь: | Lever /Rear |
| Парткод: | A161112101 |
| Деталь: | RAIL |
| Парткод: | A161110105 |
| Деталь: | Contact /K |
| Парткод: | A0ED111400 |
| Деталь: | SEAL |
| Парткод: | A161144900 |
| Деталь: | DUCT |
| Парткод: | A161141700 |
| Деталь: | SEAL |
| Парткод: | A161146200 |
| Деталь: | SEAL |
| Парткод: | A161144801 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A7PU109000 |
| Деталь: | GUIDE PLATE |
| Парткод: | A79J145100 |
| Деталь: | CUSHION |
| Парткод: | A79J145200 |
| Деталь: | DUCT |
| Парткод: | A79J143400 |
| Деталь: | CUSHION |
| Парткод: | A79J142701 |
| Деталь: | SEAL |
| Парткод: | A79J145000 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313100072 |
| Деталь: | CUSHION |
| Парткод: | A79J143800 |
| Деталь: | CUSHION |
| Парткод: | A79J143600 |
| Деталь: | DUCT |
| Парткод: | A79J143001 |
| Деталь: | CUSHION |
| Парткод: | A79J143200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J148300 |
| Деталь: | DUCT |
| Парткод: | A79J140501 |
| Деталь: | CUSHION |
| Парткод: | A79J141501 |
| Деталь: | CUSHION |
| Парткод: | A79J142600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J121100 |
| Деталь: | GROUND PLATE |
| Парткод: | A161122500 |
| Деталь: | GUIDE |
| Парткод: | A79J135000 |
| Деталь: | CUSHION |
| Парткод: | A79J120700 |
| Деталь: | SEAL |
| Парткод: | A79J120801 |
| Деталь: | GROUND PLATE |
| Парткод: | A161622100 |
| Деталь: | SHEET |
| Парткод: | A161626200 |
| Деталь: | ROLL |
| Парткод: | A161623400 |
| Деталь: | Reinforce Plate /Right |
| Парткод: | A79J633100 |
| Деталь: | Protection Sheet |
| Парткод: | A55V624700 |
| Деталь: | Reinforce Plate /Left |
| Парткод: | A161633202 |
| Деталь: | CUSHION |
| Парткод: | A5C1628500 |
| Деталь: | LABEL |
| Парткод: | A795942401 |
| Деталь: | HOLDER |
| Парткод: | A5C1624300 |
| Деталь: | LEVER |
| Парткод: | A161636502 |
| Деталь: | LEVER |
| Парткод: | A161626602 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161626800 |
| Деталь: | LENS |
| Парткод: | A161626000 |
| Деталь: | Light blocking Sheet |
| Парткод: | A161626100 |
| Деталь: | Label 2 |
| Парткод: | A161943200 |
| Деталь: | COVER |
| Парткод: | A5C1635001 |
| Деталь: | COVER |
| Парткод: | A161625900 |
| Деталь: | HANDLE |
| Парткод: | A161626900 |
| Деталь: | COVER |
| Парткод: | A161635117 |
| Деталь: | 2nd Cassette Assy |
| Парткод: | A79JR72200 |
| Деталь: | Label Cd |
| Парткод: | A79J943600 |
| Деталь: | Label FD |
| Парткод: | A79J941200 |
| Деталь: | Label FD |
| Парткод: | A79J943500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J402700 |
| Деталь: | Gear 17/65T |
| Парткод: | A161401300 |
| Деталь: | GEAR 25T |
| Парткод: | A161401500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J402600 |
| Деталь: | GEAR 36T |
| Парткод: | A161401100 |
| Деталь: | Gear18T |
| Парткод: | A161401000 |
| Деталь: | BUSHING |
| Парткод: | 4163510201 |
| Деталь: | SEAL |
| Парткод: | 4576536301 |
| Деталь: | HOLDER |
| Парткод: | A161403101 |
| Деталь: | SCREW |
| Парткод: | A161400100 |
| Деталь: | DETECTING PLATE |
| Парткод: | A161400401 |
| Деталь: | Detecting Seal |
| Парткод: | A161400601 |
| Деталь: | Agitating Shaft |
| Парткод: | A5C1F42000 |
| Деталь: | Fixing Plate |
| Парткод: | A161404200 |
| Деталь: | Toner Drive harness /K |
| Парткод: | A161N12801 |
| Деталь: | Stepping motor |
| Парткод: | A7PUM10700 |
| Деталь: | SEAL |
| Парткод: | 4333501201 |
| Деталь: | BUSHING |
| Парткод: | A161403000 |
| Деталь: | Detecting Actuator |
| Парткод: | A161404300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J400700 |
| Деталь: | Toner Detection harness /1 |
| Парткод: | A161N10F01 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | SEAL |
| Парткод: | A161403200 |
| Деталь: | TENSION SPRING |
| Парткод: | 4036534801 |
| Деталь: | SHUTTER |
| Парткод: | A0ED401000 |
| Деталь: | PIN |
| Парткод: | A161400800 |
| Деталь: | SEAL |
| Парткод: | A161146800 |
| Деталь: | WASHER |
| Парткод: | A5C1404600 |
| Деталь: | GEAR 40T |
| Парткод: | A79J401400 |
| Деталь: | GEAR 20T |
| Парткод: | A79J401600 |
| Деталь: | Gear18T |
| Парткод: | A79J401700 |
| Деталь: | WASHER |
| Парткод: | A79J401800 |
| Деталь: | SPRING |
| Парткод: | A79J401900 |
| Деталь: | COVER |
| Парткод: | A161278600 |
| Деталь: | CCD Cable |
| Парткод: | A7PUN14500 |
| Деталь: | PLATE SPRING |
| Парткод: | A161278900 |
| Деталь: | CCD ASSY |
| Парткод: | A79JR72700 |
| Деталь: | Scanner Wiring /4 |
| Парткод: | A161N14000 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED271300 |
| Деталь: | MIRROR |
| Парткод: | A0ED271200 |
| Деталь: | Lamp |
| Парткод: | A61FM31100 |
| Деталь: | BUSHING |
| Парткод: | A161271000 |
| Деталь: | FRAME |
| Парткод: | A161270102 |
| Деталь: | BUSHING |
| Парткод: | A161271100 |
| Деталь: | GUIDE |
| Парткод: | A161270600 |
| Деталь: | GASKET |
| Парткод: | A79JM90900 |
| Деталь: | FERRITECORE |
| Парткод: | A5C1M92100 |
| Деталь: | FERRITECORE |
| Парткод: | A61FM90200 |
| Деталь: | FERRITECORE |
| Парткод: | A49FM90100 |
| Деталь: | FERRITECORE |
| Парткод: | A7AHM90300 |
| Деталь: | Read Cover /Rear |
| Парткод: | A7PU170200 |
| Деталь: | LABEL |
| Парткод: | A7PU940600 |
| Деталь: | Read Cover |
| Парткод: | A64J170700 |
| Деталь: | Read Cover |
| Парткод: | A79J170601 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J169300 |
| Деталь: | Read Cover /Right |
| Парткод: | A7PU170400 |
| Деталь: | COVER |
| Парткод: | A02E167700 |
| Деталь: | HOLDER |
| Парткод: | A79J170800 |
| Деталь: | Read Cover /Front |
| Парткод: | A79J170100 |
| Деталь: | LABEL |
| Парткод: | A3EW944600 |
| Деталь: | LABEL |
| Парткод: | A0HF952400 |
| Деталь: | Read Cover /Left |
| Парткод: | A79J170300 |
| Деталь: | Scanner Relay harness /100V |
| Парткод: | A161N11C01 |
| Деталь: | CUSHION |
| Парткод: | A79JM90000 |
| Деталь: | CUSHION |
| Парткод: | A79JM90100 |
| Деталь: | Gasket /3 |
| Парткод: | A797M90200 |
| Деталь: | HOLDER |
| Парткод: | A5C1563100 |
| Деталь: | SPACER |
| Парткод: | 4040561000 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161568600 |
| Деталь: | GUIDE |
| Парткод: | A5C1563500 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A0ED563900 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A64J564101 |
| Деталь: | GUIDE PLATE |
| Парткод: | A7PU568400 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A64JR71100 |
| Деталь: | SHAFT |
| Парткод: | A5C1563400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161564001 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030301703 |
| Деталь: | SHAFT |
| Парткод: | A161563300 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4532341001 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161563901 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161564400 |
| Деталь: | SPACER |
| Парткод: | A161564200 |
| Деталь: | LEVER |
| Парткод: | A5C1564101 |
| Деталь: | SPACER |
| Парткод: | A161564300 |
| Деталь: | SHEET |
| Парткод: | A5C1565600 |
| Деталь: | GUIDE |
| Парткод: | A7PU567700 |
| Деталь: | GUIDE |
| Парткод: | A7PU567600 |
| Деталь: | GUIDE |
| Парткод: | A7PU567500 |
| Деталь: | Relay Connector |
| Парткод: | A0EDM60001 |
| Деталь: | Release Lever |
| Парткод: | A161116202 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A161119500 |
| Деталь: | FAN MOTOR |
| Парткод: | 4556M10000 |
| Деталь: | Brushless motor |
| Парткод: | A782M10100 |
| Деталь: | Gear /8 39T |
| Парткод: | A782571600 |
| Деталь: | Gear /3 47T/18T |
| Парткод: | A782571300 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A782571500 |
| Деталь: | Gear /7 25T |
| Парткод: | A782571400 |
| Деталь: | BUSHING |
| Парткод: | A161210200 |
| Деталь: | Gear /5 18T |
| Парткод: | A782571100 |
| Деталь: | FLANGE |
| Парткод: | A782572000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782566000 |
| Деталь: | Torsion Coil spring /5 |
| Парткод: | A782572900 |
| Деталь: | Gear /4 32T |
| Парткод: | A782571201 |
| Деталь: | SHAFT |
| Парткод: | A782573401 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782570800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782130500 |
| Деталь: | PIN |
| Парткод: | A782573800 |
| Деталь: | DUCT |
| Парткод: | A79J830600 |
| Деталь: | SEAL |
| Парткод: | A79J831501 |
| Деталь: | DUCT |
| Парткод: | A79J830500 |
| Деталь: | CUSHION |
| Парткод: | A79J831100 |
| Деталь: | CUSHION |
| Парткод: | A79J831600 |
| Деталь: | Guide Door /Right |
| Парткод: | A79J810100 |
| Деталь: | Cover Door |
| Парткод: | A161815100 |
| Деталь: | GUIDE PLATE |
| Парткод: | A79J812201 |
| Деталь: | Roller /C |
| Парткод: | A161814601 |
| Деталь: | ROLLER |
| Парткод: | A79J813700 |
| Деталь: | BUSHING |
| Парткод: | A02E815200 |
| Деталь: | Knob /A |
| Парткод: | A161814700 |
| Деталь: | Label M5 |
| Парткод: | A161946100 |
| Деталь: | Contact /A |
| Парткод: | A5C1814200 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | Open/close Claw |
| Парткод: | A5C1815700 |
| Деталь: | Swing Spring |
| Парткод: | A161815800 |
| Деталь: | Guide Plate /1 |
| Парткод: | A7PU810200 |
| Деталь: | Sound shield Seal /3 |
| Парткод: | A79J816700 |
| Деталь: | Sound shield Seal /2 |
| Парткод: | A79J816600 |
| Деталь: | Bushing /A |
| Парткод: | A161813300 |
| Деталь: | Spacer /A |
| Парткод: | A161816400 |
| Деталь: | Stepping motor |
| Парткод: | A2X0M10600 |
| Деталь: | Frame /ASSY |
| Парткод: | A79J811200 |
| Деталь: | Pulley 22T |
| Парткод: | A0ED811700 |
| Деталь: | TIMING BELT 200L |
| Парткод: | A79J819000 |
| Деталь: | ROLL |
| Парткод: | A79J819800 |
| Деталь: | Contact /B |
| Парткод: | A5C1814300 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A79J812401 |
| Деталь: | COVER |
| Парткод: | A79J812300 |
| Деталь: | LEVER |
| Парткод: | A79J812600 |
| Деталь: | BUSHING |
| Парткод: | A79J812800 |
| Деталь: | LEVER |
| Парткод: | A79J812500 |
| Деталь: | SEAL |
| Парткод: | A79J812900 |
| Деталь: | SOLENOID |
| Парткод: | 9321220032 |
| Деталь: | COVER |
| Парткод: | A79J814901 |
| Деталь: | Sound shield Seal /4 |
| Парткод: | A79J816800 |
| Деталь: | LABEL |
| Парткод: | A00F941100 |
| Деталь: | Collar /A |
| Парткод: | A161813801 |
| Деталь: | Seal /4 |
| Парткод: | A161146900 |
| Деталь: | Duct /1 |
| Парткод: | A161147500 |
| Деталь: | Seal /1 |
| Парткод: | A161143500 |
| Деталь: | TONER FILTER ASSY |
| Парткод: | A161R72811 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A5C1142001 |
| Деталь: | SEAL |
| Парткод: | A02E117300 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313100072 |
| Деталь: | Duct /2 |
| Парткод: | A161141500 |
| Деталь: | HOLDER |
| Парткод: | A7PU141800 |
| Деталь: | SEAL |
| Парткод: | A79J146400 |
| Деталь: | Seal /3 |
| Парткод: | A161146600 |
| Деталь: | SEAL |
| Парткод: | A161146500 |
| Деталь: | DUCT |
| Парткод: | A161147600 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A79J121701 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A79J122701 |
| Деталь: | SEAL |
| Парткод: | A161403701 |
| Деталь: | COVER |
| Парткод: | A79J401101 |
| Деталь: | COVER |
| Парткод: | A79J401201 |
| Деталь: | COVER |
| Парткод: | A79J401301 |
| Деталь: | COVER |
| Парткод: | A79J401501 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038101401 |
| Деталь: | SPACER |
| Парткод: | A161403901 |
| Деталь: | Label Toner 1 |
| Парткод: | A0ED940600 |
| Деталь: | SEAL |
| Парткод: | A161402502 |
| Деталь: | SHUTTER |
| Парткод: | A161402403 |
| Деталь: | SEAL |
| Парткод: | A161403800 |
| Деталь: | SEAL |
| Парткод: | A161403500 |
| Деталь: | SEAL |
| Парткод: | A161403600 |
| Деталь: | SEAL |
| Парткод: | A161403300 |
| Деталь: | SEAL |
| Парткод: | A161403403 |
| Деталь: | COVER |
| Парткод: | A161402114 |
| Деталь: | SEAL |
| Парткод: | A5C1404500 |
| Деталь: | Seal /1 |
| Парткод: | A161404001 |
| Деталь: | Seal /2 |
| Парткод: | A161404100 |
| Деталь: | Sub Hopper Assy |
| Парткод: | A79JR70500 |
| Деталь: | Sub Hopper Assy |
| Парткод: | A79JR70600 |
| Деталь: | Sub Hopper Assy |
| Парткод: | A79JR70700 |
| Деталь: | Sub Hopper Assy |
| Парткод: | A79JR72800 |
| Деталь: | Relay Connector |
| Парткод: | A0EDM60001 |
| Деталь: | HOLDER |
| Парткод: | A2XK400001 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A2XK400100 |
| Деталь: | SEAL |
| Парткод: | A79J400200 |
| Деталь: | Toner Detection harness /2 |
| Парткод: | A2XKN10B00 |
| Деталь: | SUCTION PLATE |
| Парткод: | A79J403100 |
| Деталь: | Conveyance Wiring |
| Парткод: | A161N10H01 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | Spring /C |
| Парткод: | A161712700 |
| Деталь: | Ground Spring /A |
| Парткод: | A161712401 |
| Деталь: | Ground Plate /C |
| Парткод: | A5C1715100 |
| Деталь: | Ground Spring /B |
| Парткод: | A5C1711000 |
| Деталь: | FIXED POWER RESISTORS |
| Парткод: | V800500300 |
| Деталь: | Ground Plate /A |
| Парткод: | A5C1710900 |
| Деталь: | Actuator /A |
| Парткод: | A2XK710100 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Holder /A |
| Парткод: | A161710103 |
| Деталь: | Transfer Holder /2 |
| Парткод: | A161550700 |
| Деталь: | Support Plate /Front |
| Парткод: | A5C1711800 |
| Деталь: | Compressing Coil spring /2 |
| Парткод: | A0ED551000 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED551100 |
| Деталь: | Fixing Part /Lower |
| Парткод: | A161712300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED550900 |
| Деталь: | Guide Seal |
| Парткод: | A5C1551701 |
| Деталь: | Ground Spring /C |
| Парткод: | A161712500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161551600 |
| Деталь: | Transfer Holder /2 |
| Парткод: | A161551500 |
| Деталь: | Adjusting Plate |
| Парткод: | A161104101 |
| Деталь: | 2nd Image Transfer Roller Assy |
| Парткод: | A79JR71100 |
| Деталь: | Neutralizing Part |
| Парткод: | A0ED550800 |
| Деталь: | Vertical Transport Assy |
| Парткод: | A79JR72300 |
| Деталь: | Pressing Spring |
| Парткод: | A161711200 |
| Деталь: | BUSHING |
| Парткод: | 4131253701 |
| Деталь: | Pulley 34T |
| Парткод: | A782210800 |
| Деталь: | Paper exit Timing belt 148L |
| Парткод: | A782210200 |
| Деталь: | Stepping motor |
| Парткод: | A3CKM10300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782212500 |
| Деталь: | Neutralizing Brush /2 |
| Парткод: | A782891600 |
| Деталь: | Wiring Cover |
| Парткод: | A782891700 |
| Деталь: | Paper exit Washer |
| Парткод: | A782115800 |
| Деталь: | Mounting Pedestal |
| Парткод: | A782890700 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | A782890000 |
| Деталь: | Neutralizing Brush /1 |
| Парткод: | A782891500 |
| Деталь: | BUSHING |
| Парткод: | A782103200 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A5C1R90000 |
| Деталь: | Paper exit Spring |
| Парткод: | A782101900 |
| Деталь: | Sensor Cover |
| Парткод: | A782890600 |
| Деталь: | Paper exit Cover |
| Парткод: | A782890100 |
| Деталь: | CUSHION |
| Парткод: | A782104500 |
| Деталь: | Paper exit Actuator |
| Парткод: | A782890200 |
| Деталь: | FILTER |
| Парткод: | A161145000 |
| Деталь: | Seal /3 |
| Парткод: | A161144500 |
| Деталь: | Seal /3 |
| Парткод: | A161143601 |
| Деталь: | Power supply Assy /230V |
| Парткод: | A79JR70100 |
| Деталь: | Power supply Assy /100V |
| Парткод: | A79JR70000 |
| Деталь: | SHEET |
| Парткод: | A5AY131100 |
| Деталь: | Cooling Duct connector |
| Парткод: | A79J140801 |
| Деталь: | Seal /1 |
| Парткод: | V651010002 |
| Деталь: | Vibrationproof Rubber |
| Парткод: | A161143400 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | COVER |
| Парткод: | A79J100600 |
| Деталь: | FILTER |
| Парткод: | A7PU101500 |
| Деталь: | FERRITECORE |
| Парткод: | A3EWM90500 |
| Деталь: | FERRITECORE |
| Парткод: | A5C1M92100 |
| Деталь: | THERMISTOR |
| Парткод: | A0P0M50300 |
| Деталь: | ADF Wiring /50 |
| Парткод: | A782N12300 |
| Деталь: | Washer /1 |
| Парткод: | A782115700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782212300 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140071 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A108210400 |
| Деталь: | ROLLER |
| Парткод: | A782102900 |
| Деталь: | Stepping motor |
| Парткод: | A782M10200 |
| Деталь: | ADF Wiring /16 |
| Парткод: | A782N11500 |
| Деталь: | Tension Plate |
| Парткод: | A782231000 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A782117900 |
| Деталь: | WEIGHT |
| Парткод: | A782118300 |
| Деталь: | BUSHING |
| Парткод: | A782263801 |
| Деталь: | Pulley 14T |
| Парткод: | A782262900 |
| Деталь: | FLANGE |
| Парткод: | A0HU250500 |
| Деталь: | Belt 100L |
| Парткод: | A782263000 |
| Деталь: | Pulley T25 |
| Парткод: | A782269800 |
| Деталь: | Belt 140L |
| Парткод: | A782268900 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A782118000 |
| Деталь: | ARM |
| Парткод: | A782262200 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A5C1R90000 |
| Деталь: | ROLL |
| Парткод: | A782262800 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A782263300 |
| Деталь: | BRUSH |
| Парткод: | A3CK300200 |
| Деталь: | SHAFT |
| Парткод: | A782262500 |
| Деталь: | SHEET |
| Парткод: | A782264501 |
| Деталь: | SPRING |
| Парткод: | A782264300 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A782269200 |
| Деталь: | GUIDE |
| Парткод: | A782262101 |
| Деталь: | SHAFT |
| Парткод: | A782262700 |
| Деталь: | Timing belt 468L |
| Парткод: | A782213300 |
| Деталь: | ARM |
| Парткод: | A782262300 |
| Деталь: | BUSHING |
| Парткод: | A782263700 |
| Деталь: | Pulley /2 27T |
| Парткод: | A782213100 |
| Деталь: | PULLEY |
| Парткод: | A782230700 |
| Деталь: | ADF Wiring /6 |
| Парткод: | A782N10501 |
| Деталь: | STOPPER |
| Парткод: | A108703100 |
| Деталь: | Stepping motor |
| Парткод: | A782M10000 |
| Деталь: | CONNECTOR |
| Парткод: | V651010034 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | REINFORCE PLATE /2 |
| Парткод: | A782573000 |
| Деталь: | REINFORCE PLATE /1 |
| Парткод: | A782573100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A782572100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A782571900 |
| Деталь: | Protection Seal /2 |
| Парткод: | A782561900 |
| Деталь: | GROUND PLATE |
| Парткод: | A782571800 |
| Деталь: | ROLL |
| Парткод: | 9J07300801 |
| Деталь: | PLATE SPRING |
| Парткод: | A108890500 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Neutralizing Brush |
| Парткод: | A108891300 |
| Деталь: | GUIDE |
| Парткод: | A108561500 |
| Деталь: | GUIDE |
| Парткод: | 9J07341102 |
| Деталь: | Protection Seal /1 |
| Парткод: | A782561801 |
| Деталь: | Gear /6 23T |
| Парткод: | A782570900 |
| Деталь: | COVER |
| Парткод: | A782565000 |
| Деталь: | BUSHING |
| Парткод: | A0ED891100 |
| Деталь: | Paper exit Guide /Upper |
| Парткод: | A79J895601 |
| Деталь: | Paper exit Guide /Lower |
| Парткод: | A79J895200 |
| Деталь: | ROLL |
| Парткод: | 4004590301 |
| Деталь: | SPRING |
| Парткод: | A161892400 |
| Деталь: | ROLL |
| Парткод: | A64J891100 |
| Деталь: | SHAFT |
| Парткод: | 4025598401 |
| Деталь: | ROLLER |
| Парткод: | A79J895400 |
| Деталь: | GROUND SPRING |
| Парткод: | A161900201 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 1164202801 |
| Деталь: | Neutralizing Brush |
| Парткод: | A161894000 |
| Деталь: | Ground Contact /Upper |
| Парткод: | A161895502 |
| Деталь: | Ground Contact /Lower |
| Парткод: | A161895600 |
| Деталь: | WASHER |
| Парткод: | A64J891200 |
| Деталь: | ROLL |
| Парткод: | A2X0901100 |
| Деталь: | Relay Wiring /5 |
| Парткод: | A79JN10Q00 |
| Деталь: | Guide Lever |
| Парткод: | A5C1890400 |
| Деталь: | Guide Part /Lower |
| Парткод: | A161890203 |
| Деталь: | GROUND SPRING |
| Парткод: | A161900300 |
| Деталь: | CUSHION |
| Парткод: | A161893601 |
| Деталь: | BUSHING |
| Парткод: | A161891000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161892300 |
| Деталь: | COVER |
| Парткод: | A7PU890700 |
| Деталь: | SOLENOID ASSY |
| Парткод: | A79JR72400 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A79J892000 |
| Деталь: | Caulking(Mounting Plate) |
| Парткод: | A161F89003 |
| Деталь: | CUSHION |
| Парткод: | A79J893700 |
| Деталь: | COLLAR |
| Парткод: | A0ED897700 |
| Деталь: | GROUND SPRING |
| Парткод: | A161900100 |
| Деталь: | ROLLER |
| Парткод: | A79J890300 |
| Деталь: | DUCT |
| Парткод: | A79J893500 |
| Деталь: | DUCT |
| Парткод: | A79J894500 |
| Деталь: | Paper exit Main body |
| Парткод: | A79J890201 |
| Деталь: | CLUTCH |
| Парткод: | A64JM20000 |
| Деталь: | SHAFT |
| Парткод: | A79J898200 |
| Деталь: | ROLL |
| Парткод: | A79J897501 |
| Деталь: | COLLAR |
| Парткод: | A79J897800 |
| Деталь: | CUSHION |
| Парткод: | A79J893800 |
| Деталь: | Adjusting Plate |
| Парткод: | A161121300 |
| Деталь: | Adjusting Plate |
| Парткод: | A161102500 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06M60100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A161137100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161151200 |
| Деталь: | HOLDER |
| Парткод: | A5C1121201 |
| Деталь: | Wiring Cover /B |
| Парткод: | A161592900 |
| Деталь: | LOCK CLAW |
| Парткод: | A0ED712100 |
| Деталь: | Support Part /Upper |
| Парткод: | A161811500 |
| Деталь: | Lock plate |
| Парткод: | A161811001 |
| Деталь: | Paper feed Guide |
| Парткод: | A5C1590500 |
| Деталь: | Open/close Handle |
| Парткод: | A161811100 |
| Деталь: | Lock /Middle |
| Парткод: | A5C1815200 |
| Деталь: | Lock Part /Lower |
| Парткод: | A161811302 |
| Деталь: | Pulling Spring |
| Парткод: | A64J815500 |
| Деталь: | SHAFT |
| Парткод: | A161815300 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161815900 |
| Деталь: | Lock Claw /Lower |
| Парткод: | A5C1811600 |
| Деталь: | ROLL |
| Парткод: | A161815400 |
| Деталь: | Guide Plate /2 |
| Парткод: | A161810305 |
| Деталь: | Guide Door |
| Парткод: | A161815000 |
| Деталь: | Ground Guide |
| Парткод: | A161816200 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A161620904 |
| Деталь: | CUSHION |
| Парткод: | A161624100 |
| Деталь: | RACK |
| Парткод: | A161621100 |
| Деталь: | LABEL MAX LEVEL |
| Парткод: | A161943700 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A161620600 |
| Деталь: | GEAR |
| Парткод: | A161620701 |
| Деталь: | CUSHION |
| Парткод: | A795566000 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A795622700 |
| Деталь: | Auxiliary Guide /2 |
| Парткод: | A795622600 |
| Деталь: | Operation Lever |
| Парткод: | A795621301 |
| Деталь: | Auxiliary Guide /1 |
| Парткод: | A795622500 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH621000 |
| Деталь: | LOCK LEVER |
| Парткод: | A7AH621200 |
| Деталь: | LABEL |
| Парткод: | A161943000 |
| Деталь: | REGULATING PLATE |
| Парткод: | A795620800 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030322601 |
| Деталь: | LIFTING PLATE |
| Парткод: | A161620400 |
| Деталь: | GUIDE |
| Парткод: | A0ED620200 |
| Деталь: | LEVER |
| Парткод: | 4030320601 |
| Деталь: | HOLDER |
| Парткод: | A795565700 |
| Деталь: | LEVER |
| Парткод: | A795565800 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A795565900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A795621900 |
| Деталь: | LEVER |
| Парткод: | A161621411 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | LABEL |
| Парткод: | A02E940300 |
| Деталь: | REGULATING PLATE |
| Парткод: | A795565000 |
| Деталь: | PLATE SPRING |
| Парткод: | A795565600 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A795565500 |
| Деталь: | LOCK LEVER |
| Парткод: | A795565100 |
| Деталь: | LOCK LEVER |
| Парткод: | A795565200 |
| Деталь: | COVER |
| Парткод: | A795565300 |
| Деталь: | Operation Lever |
| Парткод: | A795565400 |
| Деталь: | ACTUATOR |
| Парткод: | A0ED620701 |
| Деталь: | Lifting Shaft |
| Парткод: | A161621600 |
| Деталь: | Paper feed Cassette |
| Парткод: | A79J620100 |
| Деталь: | GUIDE PLATE |
| Парткод: | A782576100 |
| Деталь: | CUSHION |
| Парткод: | A782562101 |
| Деталь: | Arm /Front |
| Парткод: | A782569000 |
| Деталь: | Light blocking Part |
| Парткод: | A782707400 |
| Деталь: | SHAFT |
| Парткод: | A782573501 |
| Деталь: | Pulley 21T |
| Парткод: | 9J07330801 |
| Деталь: | ROLLER |
| Парткод: | 9J07330102 |
| Деталь: | Arm /Front |
| Парткод: | A782568901 |
| Деталь: | Lever /2 |
| Парткод: | A782569800 |
| Деталь: | CLUTCH |
| Парткод: | A07H570500 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | Paper feed Shaft |
| Парткод: | A782569200 |
| Деталь: | Timing belt 128L |
| Парткод: | A782569900 |
| Деталь: | Pulley 19T |
| Парткод: | 9J07331901 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | ADF Wiring /9 |
| Парткод: | A782N10801 |
| Деталь: | Positioning Shaft /1 |
| Парткод: | A782101600 |
| Деталь: | SHAFT |
| Парткод: | A782101000 |
| Деталь: | Gear /2 25T |
| Парткод: | A782569300 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A5C1R90000 |
| Деталь: | RING |
| Парткод: | A782211500 |
| Деталь: | GEAR 27T |
| Парткод: | A782211400 |
| Деталь: | HOLDER |
| Парткод: | A782212000 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A782211900 |
| Деталь: | CLUTCH |
| Парткод: | A3CKM20000 |
| Деталь: | SHAFT |
| Парткод: | A782211600 |
| Деталь: | BUSHING |
| Парткод: | A108260700 |
| Деталь: | Stepping motor |
| Парткод: | A2X0M10300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782212701 |
| Деталь: | GROUND PLATE |
| Парткод: | A782211700 |
| Деталь: | Gear18T |
| Парткод: | A108213200 |
| Деталь: | Pulley 27T |
| Парткод: | A782211300 |
| Деталь: | Timing belt 124L |
| Парткод: | A782214300 |
| Деталь: | FLANGE |
| Парткод: | A782211800 |
| Деталь: | BUSHING |
| Парткод: | 4131253701 |
| Деталь: | Guide /J |
| Парткод: | A782707201 |
| Деталь: | SPRING |
| Парткод: | A782704301 |
| Деталь: | ADF Wiring /3 |
| Парткод: | A782N10200 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A161561000 |
| Деталь: | DRIVE ROLLER |
| Парткод: | A161578100 |
| Деталь: | Photoreflector |
| Парткод: | A0EDM50100 |
| Деталь: | GUIDE PLATE |
| Парткод: | A161578212 |
| Деталь: | Conveyance Detection harness |
| Парткод: | A161N12701 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161571100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161560900 |
| Деталь: | ACTUATOR |
| Парткод: | A161561600 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Paper feed Frame |
| Парткод: | A161560302 |
| Деталь: | GROUND PLATE |
| Парткод: | A5C1560600 |
| Деталь: | BALL BEARING |
| Парткод: | A00J617900 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A161562800 |
| Деталь: | SHAFT |
| Парткод: | A161560500 |
| Деталь: | GEAR 26T |
| Парткод: | A161562400 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | BUSHING |
| Парткод: | 4131300301 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A64J564101 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | A64J564201 |
| Деталь: | CLUTCH |
| Парткод: | A02E561100 |
| Деталь: | GEAR 34T |
| Парткод: | A161562300 |
| Деталь: | GEAR 28T |
| Парткод: | A161562600 |
| Деталь: | SHAFT |
| Парткод: | A161562000 |
| Деталь: | BUSHING |
| Парткод: | A161562500 |
| Деталь: | HOLDER |
| Парткод: | A161562101 |
| Деталь: | TORSION SPRING |
| Парткод: | A161567400 |
| Деталь: | LEVER |
| Парткод: | A161567300 |
| Деталь: | SHAFT |
| Парткод: | A02E560800 |
| Деталь: | CLUTCH |
| Парткод: | A64JM20000 |
| Деталь: | GEAR 24T |
| Парткод: | A2XK709000 |
| Деталь: | Paperfeed Wiring /2 |
| Парткод: | A2XKN10H01 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A161563000 |
| Деталь: | CUSHION |
| Парткод: | A161578700 |
| Деталь: | CUSHION |
| Парткод: | A161568901 |
| Деталь: | Pulley 22T |
| Парткод: | A0ED811700 |
| Деталь: | Drive Belt 266L |
| Парткод: | A161719000 |
| Деталь: | Gear 22/23T |
| Парткод: | A64J709100 |
| Деталь: | COLLAR |
| Парткод: | A0ED811900 |
| Деталь: | Ground Spring /D |
| Парткод: | A161712900 |
| Деталь: | Cover /C |
| Парткод: | A161712600 |
| Деталь: | Bushing /1 |
| Парткод: | A161713100 |
| Деталь: | Roller /A |
| Парткод: | A161710500 |
| Деталь: | Idler Roller /A |
| Парткод: | A161825700 |
| Деталь: | BUSHING |
| Парткод: | A02E815200 |
| Деталь: | Label M6 |
| Парткод: | A161946400 |
| Деталь: | Guide Plate /A |
| Парткод: | A5C1710200 |
| Деталь: | Lock Shaft /A |
| Парткод: | A161711300 |
| Деталь: | Spring /B |
| Парткод: | A161711700 |
| Деталь: | Label M1 |
| Парткод: | A161946200 |
| Деталь: | Lock Shaft |
| Парткод: | A5C1711500 |
| Деталь: | Open/close Lever |
| Парткод: | A161711600 |
| Деталь: | Fixing Part |
| Парткод: | A161714500 |
| Деталь: | Ground Plate /D |
| Парткод: | A161712000 |
| Деталь: | ACTUATOR |
| Парткод: | A161713500 |
| Деталь: | Spring /D |
| Парткод: | A161712800 |
| Деталь: | Conveyance Spring /B |
| Парткод: | A161714600 |
| Деталь: | Ground Plate /E |
| Парткод: | A161712100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161710405 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | Lock plate |
| Парткод: | A161816300 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED702400 |
| Деталь: | Guide Plate /B |
| Парткод: | A161710300 |
| Деталь: | Gear 23T |
| Парткод: | A64J719100 |
| Деталь: | Support Plate /Rear |
| Парткод: | A161711901 |
| Деталь: | GUIDE PLATE |
| Парткод: | A79J811700 |
| Деталь: | Mounting Plate /3 |
| Парткод: | A161814401 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | Conveyance Relay harness |
| Парткод: | A79JN10701 |
| Деталь: | Mounting Plate /2 |
| Парткод: | A161810801 |
| Деталь: | Roller /1 |
| Парткод: | A161810600 |
| Деталь: | Cushion /A |
| Парткод: | A161825301 |
| Деталь: | Pressing Spring /A |
| Парткод: | A161813600 |
| Деталь: | Holding Part |
| Парткод: | A0ED815100 |
| Деталь: | Idler Roller /A |
| Парткод: | A161825700 |
| Деталь: | Cushion /B |
| Парткод: | A161825800 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A5C1M50100 |
| Деталь: | Bushing /C |
| Парткод: | A161819500 |
| Деталь: | Mounting Plate /4 |
| Парткод: | A161825102 |
| Деталь: | Contact /C |
| Парткод: | A161819400 |
| Деталь: | Bushing /B |
| Парткод: | A161814500 |
| Деталь: | BUSHING |
| Парткод: | A02E815200 |
| Деталь: | ACTUATOR |
| Парткод: | A161813200 |
| Деталь: | Wiring Part |
| Парткод: | A161825400 |
| Деталь: | Guide Plate /Front |
| Парткод: | A5C1811801 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161813400 |
| Деталь: | COVER |
| Парткод: | A79J813901 |
| Деталь: | Guide Plate /Rear |
| Парткод: | A5C1811900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J810900 |
| Деталь: | Spring /D |
| Парткод: | A161712800 |
| Деталь: | ACTUATOR |
| Парткод: | A161813001 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161813100 |
| Деталь: | Guide Plate /4 |
| Парткод: | A161810503 |
| Деталь: | Cover /D |
| Парткод: | A5C1825500 |
| Деталь: | BUSHING |
| Парткод: | A5C1825000 |
| Деталь: | BUSHING |
| Парткод: | A161825000 |
| Деталь: | Gear18T |
| Парткод: | A161819200 |
| Деталь: | Cushion /B |
| Парткод: | A161826001 |
| Деталь: | PROTECTION PART |
| Парткод: | A79J821000 |
| Деталь: | FLANGE |
| Парткод: | A782230900 |
| Деталь: | Pulley 27T |
| Парткод: | A782213500 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | Washer /1 |
| Парткод: | A782115700 |
| Деталь: | ROLLER |
| Парткод: | A782115600 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A782117900 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A5C1R90000 |
| Деталь: | Conveyance Guide |
| Парткод: | A782265102 |
| Деталь: | Idling Roller |
| Парткод: | A782563800 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A782265700 |
| Деталь: | Compressing Coil |
| Парткод: | A782265600 |
| Деталь: | Open/close Shaft /Front |
| Парткод: | A782266000 |
| Деталь: | Open/close Spring /Left |
| Парткод: | A782266900 |
| Деталь: | Lock Part /Front |
| Парткод: | A782266502 |
| Деталь: | LOCK LEVER |
| Парткод: | A108266300 |
| Деталь: | LABEL |
| Парткод: | A3CK940000 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | ROLL |
| Парткод: | A782266200 |
| Деталь: | Pulling Coil spring /3 |
| Парткод: | A782267200 |
| Деталь: | Cover Film |
| Парткод: | A782940300 |
| Деталь: | SHAFT |
| Парткод: | A782266401 |
| Деталь: | Open/close Shaft |
| Парткод: | A782266800 |
| Деталь: | GUIDE |
| Парткод: | A782266300 |
| Деталь: | Slide Stopper |
| Парткод: | A782103600 |
| Деталь: | Open/close Spring /Right |
| Парткод: | A782267000 |
| Деталь: | Conveyance Guide |
| Парткод: | A782117700 |
| Деталь: | Lock Part /Rear |
| Парткод: | A782266601 |
| Деталь: | COVER |
| Парткод: | A782267100 |
| Деталь: | SHAFT |
| Парткод: | A782268201 |
| Деталь: | SHAFT |
| Парткод: | A782266100 |
| Деталь: | PLATE SPRING |
| Парткод: | A782268001 |
| Деталь: | Ground Plate spring |
| Парткод: | A782266700 |
| Деталь: | Cover /1 |
| Парткод: | A782265800 |
| Деталь: | ADF Wiring /19 |
| Парткод: | A782N11800 |
| Деталь: | ADF Wiring /8 |
| Парткод: | A782N10700 |
| Деталь: | Guide /Middle |
| Парткод: | A782117800 |
| Деталь: | Stepping motor |
| Парткод: | A161M10300 |
| Деталь: | DC Brushless motor /30 |
| Парткод: | A79JM10300 |
| Деталь: | BUSHING |
| Парткод: | A161232300 |
| Деталь: | Frame /ASSY |
| Парткод: | A79J255600 |
| Деталь: | SHAFT |
| Парткод: | A64J231801 |
| Деталь: | SPACER |
| Парткод: | A64J231901 |
| Деталь: | CLUTCH |
| Парткод: | A64JM20000 |
| Деталь: | GEAR 27T |
| Парткод: | A161230600 |
| Деталь: | Gear 24/52T |
| Парткод: | A64J230500 |
| Деталь: | Gear 22/50T |
| Парткод: | A64J228000 |
| Деталь: | Gear 33T |
| Парткод: | A161228100 |
| Деталь: | BUSHING |
| Парткод: | A161702200 |
| Деталь: | SHAFT |
| Парткод: | A161228312 |
| Деталь: | SHAFT |
| Парткод: | A161258700 |
| Деталь: | Gear 26/35T |
| Парткод: | A161259100 |
| Деталь: | Gear 35/45T |
| Парткод: | A161259200 |
| Деталь: | CLUTCH |
| Парткод: | A161M20100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A161258501 |
| Деталь: | Slide Spacer |
| Парткод: | A1RF505400 |
| Деталь: | Slide Shaft Holder |
| Парткод: | A03U812800 |
| Деталь: | LEVER |
| Парткод: | A161228601 |
| Деталь: | LEVER |
| Парткод: | A782260600 |
| Деталь: | BUSHING |
| Парткод: | 4131253701 |
| Деталь: | Support Shaft |
| Парткод: | A782260700 |
| Деталь: | Breakaway Motor ASSY |
| Парткод: | A782R70100 |
| Деталь: | GUIDE |
| Парткод: | A782116800 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A3CK272600 |
| Деталь: | LEVER |
| Парткод: | A3CK272001 |
| Деталь: | Torsion Coil spring /2 |
| Парткод: | A782272401 |
| Деталь: | Ball bearing /1 |
| Парткод: | A782272200 |
| Деталь: | ADF Wiring /30 |
| Парткод: | A782N12100 |
| Деталь: | SHAFT |
| Парткод: | A3CK272200 |
| Деталь: | Torsion Coil spring /1 |
| Парткод: | A782272301 |
| Деталь: | Guide /2 |
| Парткод: | A782100400 |
| Деталь: | Guide /1 |
| Парткод: | A782100301 |
| Деталь: | CUSHION |
| Парткод: | A782104700 |
| Деталь: | Guide /3 |
| Парткод: | A782100501 |
| Деталь: | Guide /4 |
| Парткод: | A782100600 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A782100701 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A782100200 |
| Деталь: | GUIDE |
| Парткод: | A782100101 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A782100801 |
| Деталь: | CAM |
| Парткод: | A782260400 |
| Деталь: | GEAR 26T |
| Парткод: | A782260501 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A5C1R90000 |
| Деталь: | SHAFT |
| Парткод: | A782213400 |
| Деталь: | Fixing Plate |
| Парткод: | A782260200 |
| Деталь: | ROLL |
| Парткод: | A782272800 |
| Деталь: | GUIDE |
| Парткод: | A782100000 |
| Деталь: | HOLDER |
| Парткод: | A161561100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A161561200 |
| Деталь: | COVER |
| Парткод: | A7PU569100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161565102 |
| Деталь: | Gear 21/26T |
| Парткод: | A161576100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161575101 |
| Деталь: | PAPER FEED ASSY |
| Парткод: | A79JR70800 |
| Деталь: | COVER |
| Парткод: | A161579011 |
| Деталь: | Spring /Lower |
| Парткод: | A782714200 |
| Деталь: | Lever /1 |
| Парткод: | A782711901 |
| Деталь: | Protection Seal |
| Парткод: | A782711800 |
| Деталь: | ROLLER |
| Парткод: | 9J07340901 |
| Деталь: | SHAFT |
| Парткод: | A0HT561202 |
| Деталь: | HOLDER |
| Парткод: | A782568200 |
| Деталь: | SPRING |
| Парткод: | A782568600 |
| Деталь: | HOLDER |
| Парткод: | A3CK565100 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A782568701 |
| Деталь: | Neutralizing Brush |
| Парткод: | A782576000 |
| Деталь: | GUIDE |
| Парткод: | A3CK568300 |
| Деталь: | Mounting Plate /2 |
| Парткод: | A782712300 |
| Деталь: | GUIDE |
| Парткод: | A782710804 |
| Деталь: | Adjusting Cushion |
| Парткод: | A782704200 |
| Деталь: | Neutralizing Brush |
| Парткод: | A782710201 |
| Деталь: | Lever /Upper |
| Парткод: | A782710000 |
| Деталь: | Spring /1 |
| Парткод: | A782710100 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A782117900 |
| Деталь: | Conveyance Roller |
| Парткод: | A782711000 |
| Деталь: | Timing belt 150L |
| Парткод: | A782214400 |
| Деталь: | Mounting Plate /B |
| Парткод: | A782212600 |
| Деталь: | Stepping motor |
| Парткод: | A782M10000 |
| Деталь: | Gear 23T |
| Парткод: | A782213000 |
| Деталь: | Washer /1 |
| Парткод: | A782115700 |
| Деталь: | Spring /Lower |
| Парткод: | A782714100 |
| Деталь: | COLLAR |
| Парткод: | A782215100 |
| Деталь: | DUCT |
| Парткод: | A161140200 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | A79JR70400 |
| Деталь: | POSITIONING PLATE |
| Парткод: | A161105400 |
| Деталь: | PWB Assembly (FRB) |
| Парткод: | A7PUH00500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A79J101800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161130301 |
| Деталь: | PWB Assembly(PWB-VD2 ASSY) |
| Парткод: | A161H00800 |
| Деталь: | HOLDER |
| Парткод: | A161137802 |
| Деталь: | I/F Flatcable /1 |
| Парткод: | A79JN10C00 |
| Деталь: | Duct /3 |
| Парткод: | A79J147501 |
| Деталь: | SEAL |
| Парткод: | A79J146300 |
| Деталь: | CUSHION |
| Парткод: | A79J146500 |
| Деталь: | Duct /2 |
| Парткод: | A79J147401 |
| Деталь: | SEAL |
| Парткод: | A161146400 |
| Деталь: | Seal /2 |
| Парткод: | A2XK144201 |
| Деталь: | FERRITECORE |
| Парткод: | A79JM90A00 |
| Деталь: | Scanner Wiring |
| Парткод: | A5C1N14300 |
| Деталь: | Stepping motor |
| Парткод: | A5C1M10A00 |
| Деталь: | Pulling Spring |
| Парткод: | A161275700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161276000 |
| Деталь: | Timing belt 335L |
| Парткод: | A161275600 |
| Деталь: | Pulley 103T |
| Парткод: | A161275500 |
| Деталь: | BEARING |
| Парткод: | A161276500 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED274400 |
| Деталь: | PULLEY |
| Парткод: | A161275300 |
| Деталь: | SHAFT |
| Парткод: | A161275400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161273701 |
| Деталь: | PULLEY |
| Парткод: | A0ED273600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161273401 |
| Деталь: | BUSHING |
| Парткод: | A161271000 |
| Деталь: | FRAME |
| Парткод: | A161273100 |
| Деталь: | Pulling Spring |
| Парткод: | A0ED276301 |
| Деталь: | BUSHING |
| Парткод: | A161271100 |
| Деталь: | GUIDE PART |
| Парткод: | A161273500 |
| Деталь: | MIRROR |
| Парткод: | A0ED274300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A161273800 |
| Деталь: | Adjusting Screw |
| Парткод: | A161274600 |
| Деталь: | Plate spring /1 |
| Парткод: | A161274500 |
| Деталь: | Vibrationproof Plate |
| Парткод: | A0ED274200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782264101 |
| Деталь: | Stepping motor |
| Парткод: | A782M10400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782264201 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A5C1R90000 |
| Деталь: | Pulley T25 |
| Парткод: | A782264400 |
| Деталь: | Neutralizing Brush |
| Парткод: | A782104300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A782265201 |
| Деталь: | SPACER |
| Парткод: | A782268500 |
| Деталь: | HOUSING |
| Парткод: | A782264800 |
| Деталь: | BRUSH |
| Парткод: | A3CK300200 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A782269200 |
| Деталь: | SPRING |
| Парткод: | A782264300 |
| Деталь: | BUSHING |
| Парткод: | A782263201 |
| Деталь: | SHAFT |
| Парткод: | A782268300 |
| Деталь: | SHEET |
| Парткод: | A3CK300102 |
| Деталь: | Pulley T18 |
| Парткод: | A782264600 |
| Деталь: | BUSHING |
| Парткод: | A782269500 |
| Деталь: | Pulley /2 T18 |
| Парткод: | A782264700 |
| Деталь: | Belt 154L |
| Парткод: | A782269300 |
| Деталь: | Sheet /1 |
| Парткод: | A782265300 |
| Деталь: | Belt 230L |
| Парткод: | A782264000 |
| Деталь: | ADF Wiring /60 |
| Парткод: | A782N12400 |
| Деталь: | CUSHION |
| Парткод: | A782562101 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A161620904 |
| Деталь: | CUSHION |
| Парткод: | A161624100 |
| Деталь: | RACK |
| Парткод: | A161621100 |
| Деталь: | LABEL MAX LEVEL |
| Парткод: | A161943700 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A161620600 |
| Деталь: | GEAR |
| Парткод: | A161620701 |
| Деталь: | CUSHION |
| Парткод: | A795566000 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A795622700 |
| Деталь: | Auxiliary Guide /2 |
| Парткод: | A795622600 |
| Деталь: | Operation Lever |
| Парткод: | A795621301 |
| Деталь: | Auxiliary Guide /1 |
| Парткод: | A795622500 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A7AH621000 |
| Деталь: | LOCK LEVER |
| Парткод: | A7AH621200 |
| Деталь: | LABEL |
| Парткод: | A161943000 |
| Деталь: | REGULATING PLATE |
| Парткод: | A795620800 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030322601 |
| Деталь: | LIFTING PLATE |
| Парткод: | A161620400 |
| Деталь: | GUIDE |
| Парткод: | A0ED620200 |
| Деталь: | LEVER |
| Парткод: | 4030320601 |
| Деталь: | HOLDER |
| Парткод: | A795565700 |
| Деталь: | LEVER |
| Парткод: | A795565800 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A795565900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A795621900 |
| Деталь: | LEVER |
| Парткод: | A161631411 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | LABEL |
| Парткод: | A02E940300 |
| Деталь: | REGULATING PLATE |
| Парткод: | A795565000 |
| Деталь: | PLATE SPRING |
| Парткод: | A795565600 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A795565500 |
| Деталь: | LOCK LEVER |
| Парткод: | A795565100 |
| Деталь: | LOCK LEVER |
| Парткод: | A795565200 |
| Деталь: | COVER |
| Парткод: | A795565300 |
| Деталь: | Operation Lever |
| Парткод: | A795565400 |
| Деталь: | ACTUATOR |
| Парткод: | A0ED620701 |
| Деталь: | Lifting Shaft |
| Парткод: | A161621600 |
| Деталь: | Paper feed Cassette |
| Парткод: | A79J630100 |
Коды ошибок
10-01
10-02
10-40
11-01
11-02
11-40
12-01
12-40
13-01
13-40
14-01
14-40
15-01
15-40
16-01
16-40
17-20
20-01
20-02
20-21
20-22
30-03
32-01
32-05
66-01
66-02
66-03
66-04
66-05
66-06
66-07
66-11
66-12
66-13
66-14
66-15
66-21
66-23
66-24
66-33
66-34
72-14
72-15
72-16
72-17
72-18
72-19
72-21
72-22
72-23
72-25
72-26
72-43
72-70
72-81
72-85
72-86
72-87
75-42
75-43
92-01
92-02
92-40
93-10
99-01
99-02
99-03
99-04
99-05
99-06
99-07
99-08
99-09
C0002
C0106
C0107
C0108
C0109
C0202
C0204
C0206
C0208
C0210
C0211
C0214
C0216
C1004
C1081
C1102
C1103
C1105
C1106
C1109
C1112
C1113
C1114
C1115
C1132
C1140
C1141
C1144
C1145
C1156
C1182
C1184
C1195
C1196
C1197
C11A1
C11A2
C11E1
C1402
C2152 ... C2156
C2253, C2254
C2255, C2256
C2355
C2411, C2412
C2413, C2414
C2551, C2553, C2555
C2552, C2554
C2556, C2558
C2557
C2559, C255A, C255B
C255C
C2561, C2562
C2563, C2564
C2650
C2A11, C2A12
C2A21, C2A22
C2A23, C2A24
C3101, C3103
C3201, C3202
C3302
C3425
C3722, C3725, C3726
C3731
C3825, C3826
C3922, C3925, C3926
C392A
C392B
C4091
C40A1, C40A2
C4101
C4501
C5102, C5103
C5351
C5355
C5360
C5370
C5501
C5601
C5603
C5604
C5605, C5606
C5610
C5611
C6001
C6002
C6102, C6103
C6104, C6105
C6704
C6751
C6752
C6753
C6754, C6755
C6756
C6901, C6902, C6903
C6911, C6912, C6913
C6F01 ... C6FDD
C8101
C8107
C8302
C8401
C9401, C9402
C9403, C9404
CA051, CA052, CA053
CC140
CC151, CC152
CC155
CC156
CC159, CC15A
CC15B
CC15C
CC163
CC164
CC170 ... CC174
CC180 ... CC186
CC190
CC191
CC211
CC212
CC213
CC214
CC216
CD002
CD004, CD00F, CD020
CD010
CD011
CD012
CD013, CD014
CD015
CD016
CD017
CD030
CD041 ... CD046
CD047 ... CD04B
CD050
CD110
CD201, CD202, CD203
CD211, CD212
CD241, CD242
CD252
CD261
CD262
CD271
CD272
CD390
CD391
CD392
CD3A0
CD401 ... CD407
CD411, CD412, CD413
CD601, CD602, CD603
CD701, CD702, CD703
CD704
CD705, CD706
CDF50, CDF70, CDFA0
CDF51, CDF71, CDFA1
CE001 ... CE007
CE002
CE101
CE201
CE301 ... CE305
CED01
CEEE1, CEEE3
CEEE2
D-1
D-3
P-14
P-21
P-22
P-27
P-33
P-5, P-28
P-6, P-7, P-8, P-9
S-1
S-2
Описание
| Error code: | 10-01 |
| Description: | The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the manual bypass tray starts to feed paper. |
| Causes: | • Transport motor (M1) • Registration clutch (CL4) • Bypass paper feed clutch (CL7) • Bypass pick-up solenoid (SD1) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 10-02 |
| Description: | Low fuser temperature |
| Causes: | • Transport motor (M1) • Registration clutch (CL4) • Bypass paper feed clutch (CL7) • Bypass pick-up solenoid (SD1) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 10-40 |
| Description: | For paper fed from the manual bypass tray, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. |
| Causes: | • Transport motor (M1) • Registration clutch (CL4) • Bypass paper feed clutch (CL7) • Bypass pick-up solenoid (SD1) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 11-01 |
| Description: | The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to feed paper. |
| Causes: | • Transport motor (M1) • Tray 1 paper feed clutch (CL3) • Registration clutch (CL4) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 11-02 |
| Description: | For paper fed from the tray 1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete before the rise timing of the transport motor (M1). |
| Causes: | • Transport motor (M1) • Tray 1 paper feed clutch (CL3) • Registration clutch (CL4) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 11-40 |
| Description: | For paper fed from the tray 1, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. |
| Causes: | • Transport motor (M1) • Tray 1 paper feed clutch (CL3) • Registration clutch (CL4) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 12-01 |
| Description: | Paper at finisher input sensor |
| Causes: | • Transport motor (M1) • Tray 2 paper feed clutch (CL1) • Tray 2 vertical transport clutch (CL2) • Tray 2 vertical transport sensor (PS19) • MFP board (MFPB) |
| Error code: | 12-40 |
| Description: | Tamper motor |
| Causes: | • Transport motor (M1) • Tray 2 paper feed clutch (CL1) • Tray 2 vertical transport clutch (CL2) • Tray 2 vertical transport sensor (PS19) • MFP board (MFPB) |
| Error code: | 13-01 |
| Description: | The leading edge of the paper is not turned ON the tray 3 vertical transport sensor (PS113) even after the lapse of a given period of time after the tray 3 starts to feed paper. |
| Causes: | • Tray 3 paper feed motor (M111) • Tray 3 vertical transport motor (M112) • Tray 3 vertical transport sensor (PS113) • PC control board (PCCB) |
| Error code: | 13-40 |
| Description: | For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. |
| Causes: | • Tray 3 paper feed motor (M111) • Tray 3 vertical transport motor (M112) • Tray 3 vertical transport sensor (PS113) • PC control board (PCCB) |
| Error code: | 14-01 |
| Description: | The leading edge of the paper is not turned ON the tray 4 vertical transport sensor (PS123) even after the lapse of a given period of time after the tray 4 starts to feed paper. |
| Causes: | • Tray 4 paper feed motor (M121) • Tray 4 vertical transport motor (M122) • Tray 4 vertical transport sensor (PS123) • PC control board (PCCB) |
| Error code: | 14-40 |
| Description: | For paper fed from the tray 4, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. |
| Causes: | • Tray 4 paper feed motor (M121) • Tray 4 vertical transport motor (M122) • Tray 4 vertical transport sensor (PS123) • PC control board (PCCB) |
| Error code: | 15-01 |
| Description: | The leading edge of the paper is not turned ON the paper feed sensor (PS3) even after the lapse of a given period of time after the LCT starts to feed paper. |
| Causes: | • Paper feed motor (M2) • Paper feed sensor (PS3) • LU drive board (LUDB) • MFP board (MFPB) • PC control board (PCCB) |
| Error code: | 15-40 |
| Description: | For paper fed from the LCT, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. |
| Causes: | • Paper feed motor (M2) • Paper feed sensor (PS3) • LU drive board (LUDB) • MFP board (MFPB) • PC control board (PCCB) |
| Error code: | 16-01 |
| Description: | The leading edge of the paper is not turned ON the vertical transport sensor (PS133) even after the lapse of a given period of time after the LCC starts to feed paper. |
| Causes: | • Paper feed motor (M131) • Vertical transport motor (M132) • Vertical transport sensor (PS133) • PC control board (PCCB) |
| Error code: | 16-40 |
| Description: | For paper fed from the LCC, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. |
| Causes: | • Paper feed motor (M131) • Vertical transport motor (M132) • Vertical transport sensor (PS133) • PC control board (PCCB) |
| Error code: | 17-20 |
| Description: | Misfeed at LCT transport section (When LU-205 or LU303 is installed). 17-20 The tray 2 vertical transport sensor (PS12) is not turned ON even after the set period of time has elapsed after the LU paper feed sensor (PS3) turns ON by a paper. - Paper jam of a sheet of paper left at the LCT transport section results, if the LU paper feed sensor (PS3) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. |
| Causes: | • LU transport motor (M3) • LU paper feed sensor (PS3) • Tray 2 vertical transport sensor (PS12) • LU drive board (LUDB) • Paper feed/transport drive board (PFTDB) |
| Remedy: | 1 Initial check items - - 2 PS3 I/O check, sensor check LUDB CN5-8 (ON) LU-205/LU-303 4-G 3 PS12 I/O check, sensor check PFTDB CN12-10 (ON) 3-P 4 M3 operation check LUDB CN4-1 to 4 LU-205/LU-303 3-G 5 Replace LUDB. (LU-205/LU-303) - - 6 PFTDB F1 or F4 conduction check - - 7 Replace PFTDB. |
| Error code: | 20-01 |
| Display: | ***** ERROR 20 ***** I/F BOARD 01 |
| Description: | Error on Communication between I/F Board and Main Board (Time-out) |
| Causes: | • Transport motor (M1) • Tray 2 vertical transport clutch (CL2) • Registration clutch (CL4) • Registration sensor (PS1) • Tray 2 vertical transport sensor (PS19) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 20-02 |
| Display: | I/F BOARD 02 |
| Description: | Error on Communication between I/F Board and Main Board (Data Format Error) |
| Causes: | • Transport motor (M1) • Tray 2 vertical transport clutch (CL2) • Registration clutch (CL4) • Registration sensor (PS1) • Tray 2 vertical transport sensor (PS19) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 20-21 |
| Description: | <When PC-110 or PC-210 is installed> The tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the tray 3 vertical transport sensor (PS113) has been blocked by a paper. <When PC-410 is installed> The tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the vertical transport sensor (PS133) has been blocked by a paper. |
| Causes: | <When PC-110 or PC-210 is installed> • Transport motor (M1) • Tray 3 vertical transport motor (M112) • Tray 2 vertical transport clutch (CL2) • Tray 2 vertical transport sensor (PS19) • Tray 3 vertical transport sensor (PS113) • MFP board (MFPB) • PC control board (PCCB) <When PC-410 is installed> • Transport motor (M1) • Vertical transport motor (M132) • Tray 2 vertical transport clutch (CL2) • Tray 2 vertical transport sensor (PS19) • Vertical transport sensor (PS133) • MFP board (MFPB) • PC control board (PCCB) |
| Error code: | 20-22 |
| Description: | The tray 3 vertical transport sensor (PS113) is not turned ON even after the lapse of a given period of time after the tray 4 vertical transport sensor (PS123) has been blocked by a paper. |
| Causes: | • Tray 3 vertical transport motor (M112) • Tray 4 vertical transport motor (M122) • Tray 3 vertical transport sensor (PS113) • Tray 4 vertical transport sensor (PS123) • PC control board (PCCB) |
| Error code: | 30-03 |
| Description: | Misfeed at 2nd transfer section. 30-03 The paper exit sensor (PS39) is not turned ON (unblocked) even after the set period of time has elapsed after the registration sensor (PS38) turns ON (unblocked) by a paper. - Paper jam of a sheet of paper left at the 2nd transfer section results, if the registration sensor (PS38) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Paper jam of a sheet of paper left at the 2nd transfer section results, if the OHP sensor (PS40) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - When the main power switch is turned ON, residual paper detection starts between each sensor. Paper jam of a sheet of paper left at the 2nd transfer section results, if the registration sensor (PS38) or paper exit sensor (PS39) is turned from OFF (unblocked) to ON (blocked). |
| Causes: | • Registration motor (M2) • Fusing motor (M30) • Registration sensor (PS38) • OHP sensor (PS40) • Paper exit sensor (PS39) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Initial check items - - 2 PS38 I/O check, sensor check PFTDB CN2-6 (ON) 4-P 3 PS40 I/O check, sensor check PFTDB CN2-3 (REM) 4-P 4 PS39 I/O check, sensor check PFTDB CN2-12 (ON) 5-P 5 M2 operation check PFTDB CN7-1 to 4 8-P 6 M30 operation check MFPB CN16-4 (REM) MFPB CN16-7 (LOCK) 10-K 7 PFTDB F16 conduction check - - 8 Replace PFTDB. - - 9 MFPB F14E conduction check - - 10 Replace MFPB. |
| Error code: | 32-01 |
| Description: | The ADU paper passage sensor/1 (PS40) is not turned ON (unblocked) even after the lapse of a given period of time after the reverse sequence is started. |
| Causes: | • Fusing motor (M3) • Reverse motor (M4) • ADU transport motor (M5) • Paper exit clutch (CL8) • Paper exit sensor (PS3) • ADU paper passage sensor/1 (PS40) • Gate switch solenoid (SD3) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 32-05 |
| Description: | The paper exit sensor (PS3) is not turned OFF (blocked) even after the lapse of a given period of time after the paper has turned ON (unblocked) PS3. |
| Causes: | • Fusing motor (M3) • Reverse motor (M4) • ADU transport motor (M5) • Paper exit clutch (CL8) • Paper exit sensor (PS3) • ADU paper passage sensor/1 (PS40) • Gate switch solenoid (SD3) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 66-01 |
| Description: | <When DF-629 is installed> The document registration sensor (PS3) is not turned ON (unblocked) by the paper even after the set period of time has elapsed after the reverse registration operation started. |
| Causes: | • Document reading motor (M1) • Registration motor (M3) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) |
| Error code: | 66-02 |
| Description: | <When DF-629 or DF-704 is installed> The after separate sensor (PS2) is not turned ON (blocked) after a lapse of a given time after the document feed motor (M2) is turned ON. |
| Causes: | <When DF-629 is installed> • Document feed motor (M2) • After separate sensor (PS2) • Document length size sensor/1 (PS6) • Document length size sensor/2 (PS7) • Document width size sensor (VR1) • DF control board (DFCB) <When DF-704 is installed> • Document feed motor (M2) • After separate sensor (PS2) • Document length sensor/1 (PS8) • Document length sensor/2 (PS9) • Document width sensor (VR1) • DF control board (DFCB) |
| Error code: | 66-03 |
| Description: | <When DF-629 or DF-704 is installed> The after separate sensor (PS2) is not turned OFF (unblocked) after a lapse of a given time after PS2 is turned ON (blocked). |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Document feed motor (M2) • Registration motor (M3) • After separate sensor (PS2) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Document feed motor (M2) • Registration motor (M3) • After separate sensor (PS2) • Registration sensor (PS3) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-04 |
| Description: | <When DF-629 is installed> The document exit sensor (PS5) is not turned ON (blocked) after a lapse of a given time after the document reading sensor (PS4) is turned ON. <When DF-704 is installed> The document exit sensor (PS5) is not turned ON (blocked) after a lapse of a given time after the document reading sensor (PS6) is turned ON. |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Document reading sensor (PS4) • Document exit sensor (PS5) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Document exit sensor (PS5) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-05 |
| Description: | <When DF-629 is installed> The document reading sensor (PS4) is not turned OFF after a lapse of a given time after the document registration sensor (PS3) is turned OFF (blocked). <When DF-704 is installed> The document reading sensor (PS6) is not turned OFF after a lapse of a given time after the registration sensor (PS3) is turned OFF (blocked). |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Reading roll release motor (M5) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Reading roller release motor (M4) • Registration sensor (PS3) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-06 |
| Description: | <When DF-629 is installed> The document reading sensor (PS4) is turned ON earlier than a given time after PS4 is turned OFF during original transportation. <When DF-704 is installed> The document reading sensor (PS6) is turned ON earlier than a given time after PS6 is turned OFF during original transportation. |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Reading roll release motor (M5) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Reading roller release motor (M4) • Registration sensor (PS3) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-07 |
| Description: | Misfeed at DF paper feed/transport/image reading/turnover/paper exit section. Due to a remaining sheet of paper that has not been detected by sensors, before the start of a job, a sensor detects the sheet at an unexpected timing. |
| Causes: | • After separate sensor (PS4) • Registration sensor (PS5) • Before read sensor (PS6) • Exit sensor (PS7) • DF control board (DFCB) |
| Remedy: | 1 Initial check items - - 2 Make the adjustment of original stop position. - - 3 Make the adjusting the pressure of the separation roller. - - 4 PS4 I/O check, sensor check DFCB CN6-5 (ON) DF 7-J 5 PS5 I/O check, sensor check DFCB CN6-17 (ON) DF 9-J 6 PS6 I/O check, sensor check DFCB CN11-2 (ON) DF 1-C 7 PS7 I/O check, sensor check DFCB CN13-3 (ON) DF 7-C 8 Replace DFCB. |
| Error code: | 66-11 |
| Description: | <When DF-629 is installed> The document registration sensor (PS3) is not turned OFF (blocked) after the set period of time after PS3 is turned ON (unblocked) after the switchback registration started. |
| Causes: | • Document reading motor (M1) • Registration motor (M3) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) |
| Error code: | 66-12 |
| Description: | <When DF-629 or DF-704 is installed> The size of the original on the tray detected by DF does not match the size of the original detected by the main body. |
| Causes: | <When DF-629 is installed> • Document feed motor (M2) • After separate sensor (PS2) • Document length size sensor/1 (PS6) • Document length size sensor/2 (PS7) • Document width size sensor (VR1) • DF control board (DFCB) <When DF-704 is installed> • Document feed motor (M2) • After separate sensor (PS2) • Document length sensor/1 (PS8) • Document length sensor/2 (PS9) • Document width sensor (VR1) • DF control board (DFCB) |
| Error code: | 66-13 |
| Description: | <When DF-704 is installed> The registration sensor (PS3) is not turned ON (unblocked) after a lapse of a given time after the after separate sensor (PS2) is turned ON (blocked). |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Document feed motor (M2) • Registration motor (M3) • After separate sensor (PS2) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Document feed motor (M2) • Registration motor (M3) • After separate sensor (PS2) • Registration sensor (PS3) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-14 |
| Description: | <When DF-629 is installed> The document exit sensor (PS5) is not turned OFF (unblocked) after a lapse of a given time after the document reading sensor (PS4) is turned OFF. <When DF-704 is installed> The document exit sensor (PS5) is not turned OFF (unblocked) after a lapse of a given time after the document reading sensor (PS6) is turned OFF |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Document reading sensor (PS4) • Document exit sensor (PS5) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Document exit sensor (PS5) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-15 |
| Description: | <When DF-629 is installed> The document reading sensor (PS4) does not turn OFF after the laps of given time after the document registration sensor (PS3) is turned OFF (blocked) after the switchback read operation started. |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Reading roll release motor (M5) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Reading roller release motor (M4) • Registration sensor (PS3) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-21 |
| Description: | <When DF-629 is installed> The document reading sensor (PS4) is not turned ON after a lapse of a given time after the document registration sensor (PS3) is turned ON (unblocked). |
| Causes: | • Document reading motor (M1) • Registration motor (M3) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) |
| Error code: | 66-23 |
| Description: | <When DF-629 is installed> The document registration sensor (PS3) is not turned OFF (blocked) after a lapse of given time after PS3 is turned ON (unblocked). <When DF-704 is installed> The registration sensor (PS3) is not turned OFF (blocked) after a lapse of given time after PS3 is turned ON (unblocked). |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Document feed motor (M2) • Registration motor (M3) • After separate sensor (PS2) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Document feed motor (M2) • Registration motor (M3) • After separate sensor (PS2) • Registration sensor (PS3) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-24 |
| Description: | <When DF-629 is installed> The document exit sensor (PS5) is not turned ON (blocked) after a lapse of a given time after the document reading sensor (PS4) is turned ON. |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Document reading sensor (PS4) • Document exit sensor (PS5) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Document exit sensor (PS5) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-33 |
| Description: | <When DF-629 is installed> The document reading sensor (PS4) is not turned ON after a lapse of a given time after the document registration sensor (PS3) is turned ON (unblocked). <When DF-704 is installed> The document reading sensor (PS6) is not turned ON after a lapse of a given time after the registration sensor (PS3) is turned ON (unblocked). |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Document feed motor (M2) • Registration motor (M3) • After separate sensor (PS2) • Document registration sensor (PS3) • Document reading sensor (PS4) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Document feed motor (M2) • Registration motor (M3) • After separate sensor (PS2) • Registration sensor (PS3) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 66-34 |
| Description: | <When DF-629 is installed> The document exit sensor (PS5) is not turned OFF (unblocked) after the laps of give time after the document reading sensor (PS4) turned OFF after the switchback exit operation started. |
| Causes: | <When DF-629 is installed> • Document reading motor (M1) • Document reading sensor (PS4) • Document exit sensor (PS5) • DF control board (DFCB) <When DF-704 is installed> • Document reading motor (M1) • Document exit sensor (PS5) • Document reading sensor (PS6) • DF control board (DFCB) |
| Error code: | 72-14 |
| Description: | Misfeed at FS transport section. <When FS-536 or FS-536SD is installed> The saddle exit sensor (PS5) is not turned ON even after the set period of time has elapsed after the main tray exit sensor (PS16) is turned ON by the paper. <When FS-537 or FS-537SD is installed> The SD discharge sensor (PS35) is not turned ON even after the set period of time has elapsed after the main tray exit sensor (PS37) is turned ON by the paper. |
| Causes: | <When FS-536 or FS-536SD is installed> • Saddle exit sensor (PS5) • Main tray exit sensor (PS16) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • SD discharge sensor (PS35) • Main tray exit sensor (PS37) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS5 I/O check, sensor check FSCB J5-2 (ON) FS-536/FS-536SD 16-K 3 PS16 I/O check, sensor check FSCB J9<B>-4 (ON) FS-536/FS-536SD 11-C 4 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS35 I/O check, sensor check FSCB J15-7 (ON) FS-537/FS-537SD 15 to 16-K to L 3 PS37 I/O check, sensor check FSCB J12<B>-14 (ON) FS-537/FS-537SD 18-D 4 Replace FSCB. |
| Error code: | 72-15 |
| Description: | Misfeed at FS transport section. <When FS-536 or FS-536SD is installed> The saddle exit sensor (PS5) is not turned OFF even after the set period of time has elapsed after it is turned ON. <When FS-537 or FS-537SD is installed> The SD discharge sensor (PS35) is not turned OFF even after the set period of time has elapsed after it is turned ON by the paper. |
| Causes: | <When FS-536 or FS-536SD is installed> • Saddle exit sensor (PS5) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • SD discharge sensor (PS35) • FS control board (FSCB) |
| Remedy: | When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS5 I/O check, sensor check FSCB J5-2 (ON) FS-536/FS-536SD 16-K 3 Replace FSCB. When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS35 I/O check, sensor check FSCB J15-7 (ON) FS-537/FS-537SD 15 to 16-K to L 3 Replace FSCB. |
| Error code: | 72-16 |
| Description: | Misfeed at FS transport section. <When FS-536 or FS-536SD is installed> The FNS entrance sensor (PS4) is not turned ON even after the set period of time has elapsed after the RU transport sensor (PS60) is turned ON (blocked) by the paper. <When FS-537 or FS-537SD is installed> The FNS entrance sensor (PS34) is not turned ON even after the set period of time has elapsed after the RU transport sensor (PS60) is turned ON (blocked) by the paper. |
| Causes: | <When FS-536 or FS-536SD is installed> • RU transport sensor (PS60) • FNS entrance sensor (PS4) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • RU transport sensor (PS60) • FNS entrance sensor (PS34) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS60 I/O check, sensor check FSCB J6-7 (ON) FS-536/FS-536SD 12-K 3 PS4 I/O check, sensor check FSCB J4<B>-9 (ON) FS-536/FS-536SD 15-C 4 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS60 I/O check, sensor check FSCB J8<B>-11 (ON) FS-536/FS-536SD 12-K 3 PS34 I/O check, sensor check FSCB J8<A>-5 (ON) FS-536/FS-536SD 15-C 4 Replace FSCB. |
| Error code: | 72-17 |
| Description: | Misfeed at FS transport section. <When FS-536 or FS-536SD is installed> The FNS entrance sensor (PS4) is not turned OFF even after the set period of time has elapsed after it is turned ON by the paper. <When FS-537 or FS-537SD is installed> The FNS entrance sensor (PS34) is not turned OFF even after the set period of time has elapsed after it is turned ON by the paper. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS entrance sensor (PS4) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • FNS entrance sensor (PS34) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS4 I/O check, sensor check FSCB J4<B>-9 (ON) FS-536/FS-536SD 15-C 3 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS34 I/O check, sensor check FSCB J8<A>-5 (ON) FS-537/FS-537SD 7-D 3 Replace FSCB. |
| Error code: | 72-18 |
| Description: | Misfeed at FS transport section. <When FS-536 or FS-536SD is installed> • The main tray exit sensor (PS16) is not turned ON even after the set period of time has elapsed after the FNS entrance sensor (PS4) is turned ON by the paper. • While the buffer is controlled, the main tray exit sensor (PS16) is not tuned ON even after the set period of time has elapsed after the reverse rotation drive is started. <When FS-537 or FS-537SD is installed> The Main tray exit sensor (PS37) is not turned ON even after the set period of time has elapsed after the FNS middle sensor (PS36) is turned ON by the paper. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS entrance sensor (PS4) • Main tray exit sensor (PS16) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • FNS middle sensor (PS36) • Main tray exit sensor (PS37) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS4 I/O check, sensor check FSCB J4<B>-9 (ON) FS-536/FS-536SD 15-C 3 PS16 I/O check, sensor check FSCB J9<B>-4 (ON) FS-536/FS-536SD 11-C 4 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS36 I/O check, sensor check FSCB J12<A>-10 (ON) FS-537/FS-537SD 16-D 3 PS37 I/O check, sensor check FSCB J12<B>-14 (ON) FS-537/FS-537SD 18-D 4 Replace FSCB. |
| Error code: | 72-19 |
| Description: | Misfeed at FS transport section. <When FS-536 or FS-536SD is installed> The main tray exit sensor (PS16) is not turned OFF even after the set period of time has elapsed after it is turned ON by the paper. <When FS-537 or FS-537SD is installed> The main tray exit sensor (PS37) is not turned OFF even after the set period of time has elapsed after it is turned ON by the paper. |
| Causes: | <When FS-536 or FS-536SD is installed> • Main tray exit sensor (PS16) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Main tray exit sensor (PS37) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS16 I/O check, sensor check FSCB J9<B>-4 (ON) FS-536/FS-536SD 10-K 3 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS37 I/O check, sensor check FSCB J12<B>-14 (ON) FS-537/FS-537SD 18-D 3 Replace FSCB. |
| Error code: | 72-21 |
| Description: | Misfeed at FS transport section. <When FS-536 or FS-536SD is installed> The staple stacker paper detection sensor (PS31) is not turn OFF even after the set period of time has elapsed after the start of exiting paper. <When FS-537 or FS-537SD is installed> The alignment plate paper detection sensor (PS32) is not turn OFF even after the set period of time has elapsed after the start of exiting paper. |
| Causes: | <When FS-536 or FS-536SD is installed> • Staple stacker paper detection sensor (PS31) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Alignment plate paper detection sensor (PS32) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS31 I/O check, sensor check FSCB J12-11 (ON) FS-536/FS-536SD 6-C 3 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS32 I/O check, sensor check FSCB J21-12 (ON) FS-537/FS-537SD 5-D 3 Replace FSCB. |
| Error code: | 72-22 |
| Description: | Misfeed at FS transport section. <When FS-536 or FS-536SD is installed> The sub tray exit sensor (PS8) is not turned ON (blocked) even after the set period of time has elapsed after the paper reaches the paper transport acceleration point. <When FS-537 or FS-537SD is installed> The sub tray exit sensor (PS24) is not turned ON (blocked) even after the set period of time has elapsed after the paper reaches the paper transport acceleration point. |
| Causes: | <When FS-536 or FS-536SD is installed> • Sub tray exit sensor (PS8) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Sub tray exit sensor (PS24) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS8 I/O check, sensor check FSCB J9<B>-8 (ON) FS-536/FS-536SD 11-C 3 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS24 I/O check, sensor check FSCB J15-3 (ON) FS-537/FS-537SD 16-K to L 3 Replace FSCB. |
| Error code: | 72-23 |
| Description: | Misfeed at FS transport section. <When FS-536 or FS-536SD is installed> The sub tray exit sensor (PS8) is not turned OFF (unblocked) even after the set period of time has elapsed after PS8 turns ON (block). <When FS-537 or FS-537SD is installed> The sub tray exit sensor (PS24) is not turned OFF (unblocked) even after the set period of time has elapsed after PS24 turns ON (block). |
| Causes: | <When FS-536 or FS-536SD is installed> • Sub tray exit sensor (PS8) • FNS entrance sensor (PS4) • Main tray exit sensor (PS16) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Sub tray exit sensor (PS24) • FNS entrance sensor (PS34) • FNS middle sensor (PS36) • Main tray exit sensor (PS37) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 Clean the sensor of paper path. - - 3 PS8 I/O check, sensor check FSCB J9<B>-8 (ON) FS-536/FS-536SD 11-C 4 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 Clean the sensor of paper path. - - 3 PS24 I/O check, sensor check FSCB J15-3 (ON) FS-537/FS-537SD 16-K to L 4 Replace FSCB. |
| Error code: | 72-25 |
| Description: | <When FS-534SD is installed> The fold exit sensor (PS12) is not turned ON by the paper even after the set period of time has elapsed after the half-fold exit operation started. |
| Causes: | • Front door • Stacker unit • Fold exit sensor (PS12) • SD drive board (SDDB) • FS control board (FSCB) |
| Error code: | 72-26 |
| Description: | <When FS-534SD is installed> The fold exit sensor (PS12) is not turned OFF even after the set period of time has elapsed after it is turned ON by the paper. |
| Causes: | • Fold exit sensor (PS12) • SD drive board (SDDB) • FS control board (FSCB) |
| Error code: | 72-43 |
| Description: | Misfeed at PK JAM. <When FS-536+PK-520 or FS-536SD+PK-520 is installed> The punch position sensor (PS2) is not turned ON (unblocked) after a lapse of a given time after the punch drive motor (M1) starts rotating. <When FS-537+PK-523 or FS-537SD+PK-523 is installed> The punch position sensor (PS301) is not turned ON (unblocked) after a lapse of a given time after the punch drive motor (M301) starts rotating. - <When FS-537+PK-523 or FS-537SD+PK-523 is installed> Paper jam of a sheet of paper left at the PK section results, when the main power switch is turned ON, and the paper is detected by the paper size detect board (PSDTB). |
| Causes: | <When FS-536+PK-520 or FS-536SD +PK-520 is installed> • Punch drive motor (M1) • Punch position sensor (PS2) • FS control board (FSCB) <When FS-537+PK-523 or FS-537SD +PK-523 is installed> • Punch drive motor (M301) • PK punch home sensor/1 (PS301) • Punch control board (PKCB) • FS control board (FSCB) Residual paper jam • Paper size detect board (PSDTB) • FS control board (FSCB) |
| Remedy: | (a) When FS-536+PK-520 or FS-536SD+PK-520 is installed: 1 Initial check items - - 2 PS2 I/O check, sensor check FSCB J7-2 (ON) FS-536/FS-536SD (PK-520) 13-K 3 M1 operation check FSCB J7-7 to 8 FS-536/FS-536SD (PK-520) 13-K 4 Replace FSCB. (b) When FS-537+PK-523 or FS-537SD+PK-523 is installed: 1 Initial check items - - 2 PS301 I/O check, sensor check PKCB CN36-5 (ON) PK-523 3-C 3 M301 operation check PKCB CN35-1 to 3 PK-523 2-C 4 Replace PKCB. - - 5 Replace FSCB. (c) Residual paper jam (When FS-537+PK-523 or FS-537SD+PK-523 is installed): 1 Initial check items - - 2 Adjust the sensitivity (light intensity) by selecting [Finisher] -> [FS-FN adjustment] -> [Punch F. Sensor Intensity Adj.]. After adjustment, open and then close the front door, and check if the residual paper jam indication disappears. To turn off the main power switch, wait for more than 10 seconds until the residual paper jam indication disappears. - - 3 Replace PSDTB. 4 Replace FSCB. |
| Error code: | 72-70 |
| Description: | <When FS-533+PK-519 is installed> The paper feed sensor (PS201) is not turned OFF even after the set period of time has elapsed after it is turned ON. |
| Causes: | • Fusing motor (M3) • Paper conveyance motor (M101) • Paper feed sensor (PS201) • FS control board (FSCB) |
| Error code: | 72-81 |
| Description: | Misfeed at FS staple section. <When FS-536 or FS-536SD is installed> The stapler position sensor (center) (PS24) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the side stapler movement motor (M13) turned ON. <When FS-537 or FS-537SD is installed> The stapler position sensor (center) (PS20) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the stapler movement motor (M19) turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Side stapler movement motor (M13) • Stapler position sensor (center) (PS24) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler movement motor (M19) • Stapler position sensor (center) (PS20) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 M13 operation check FSCB J11<A>-1 to 4 FS-536/FS-536SD 4-C 3 PS24 I/O check, sensor check FSCB J11<B>-6 (ON) FS-536/FS-536SD 5-C 4 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 M19 operation check FSCB J17-10 to 13 FS-537/FS-537SD 14-D 3 PS20 I/O check, sensor check FSCB J16-5 (ON) FS-537/FS-537SD 15-D 4 Replace FSCB. |
| Error code: | 72-85 |
| Description: | Misfeed at SD transport section. <When FS-536SD is installed> The SD entrance sensor (PS1) is not turned ON (blocked) even after the set period of time has elapsed after the saddle exit sensor (PS5) is turned ON by the paper. <When FS-537SD is installed> The SD entrance sensor (PS1) is not turned ON (blocked) even after the set period of time has elapsed after the SD discharge sensor (PS35) is turned ON by the paper. |
| Causes: | <When FS-536SD is installed> • SD entrance sensor (PS1) • Saddle exit sensor (PS5) • SD control board (SDCB) • FS control board (FSCB) <When FS-537SD is installed> • SD entrance sensor (PS1) • SD discharge sensor (PS35) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | (a) When FS-536SD is installed: 1 Initial check items - - 2 PS5 I/O check, sensor check FSCB J5-2 (ON) FS-536/FS-536SD 16-K 3 PS1 I/O check, sensor check SDCB J4-8 (ON) FS-536/FS-536SD 5-L 4 Replace SDCB. - - 5 Replace FSCB. (b) When FS-537SD is installed: 1 Initial check items - - 2 PS35 I/O check, sensor check FSCB J15-7 (ON) FS-537/FS-537SD 15 to 16-K to L 3 PS1 I/O check, sensor check SDCB J4-8 (ON) FS-537/FS-537SD 4-K 4 Replace SDCB. - - 5 Replace FSCB. |
| Error code: | 72-86 |
| Description: | Misfeed at SD transport section. <When FS-536SD or FS-537SD is installed> The SD entrance sensor (PS1) is not turned OFF (unblocked) even after the set period of time has elapsed after PS1 turns ON (block). |
| Causes: | <When FS-536SD or FS-537SD is installed> • SD entrance sensor (PS1) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | (2) Procedure (a) When FS-536SD or FS-537SD is installed: 1 Initial check items - - 2 PS1 I/O check, sensor check SDCB J4-8 (ON) FS-536/FS-536SD 5-L FS-537/FS-537SD 4-K 3 Replace SDCB. (FS-536SD/FS-537SD) - - 4 Replace FSCB. (FS-536SD/FS-537SD) |
| Error code: | 72-87 |
| Description: | Misfeed at SD transport section. <When FS-536SD or FS-537SD is installed> The center staple/fold stacker paper detect sensor (PS3) is not turned ON even after the set period of time has elapsed after the SD entrance sensor (PS1) turns ON (block) by a paper. |
| Causes: | <When FS-536SD or FS-537SD is installed> • SD entrance sensor (PS1) • Center staple/fold stacker paper detect sensor (PS3) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1 Initial check items - - 2 PS1 I/O check, sensor check SDCB J4-3 (ON) FS-536/FS-536SD 4-K FS-537/FS-537SD 5-L 3 PS3 I/O check, sensor check SDCB J9-2 (ON) FS-536/FS-536SD 5-P FS-537/FS-537SD 5-P 4 Replace SDCB. (FS-536SD/FS-537SD) - - 5 Replace FSCB. (FS-536SD/FS-537SD) |
| Error code: | 75-42 |
| Description: | Misfeed at RU section. <When FS-536 or FS-536SD is installed> <When FS-537 or FS-537SD is installed> The RU transport sensor (PS60) is not turned ON (blocked) even after the set period of time has elapsed after the main body`s paper exit sensor (PS39) is turned ON (unblocked) by the paper. |
| Causes: | <When FS-536 or FS-536SD is installed> <When FS-537 or FS-537SD is installed> • Paper exit sensor (PS39) • RU transport sensor (PS60) • FS control board (FSCB) |
| Remedy: | (2) Procedure (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS39 I/O check, sensor check PFTDB CN2-12 (ON) 5-P 3 PS60 I/O check, sensor check FSCB J6-7 (ON) FS-536/FS-536SD 12-K 4 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS39 I/O check, sensor check PFTDB CN2-12 (ON) 5-P 3 PS60 I/O check, sensor check FSCB J8<B>-15 (ON) FS-537/FS-537SD 9-D 4 Replace FSCB. |
| Error code: | 75-43 |
| Description: | Misfeed at RU section. <When FS-536, FS-536SD, FS-537, or FS-537SD is installed> The RU transport sensor (PS60) is not turned OFF (unlocked) even after the set period of time has elapsed after it is turned ON (blocked). |
| Causes: | <When FS-536, FS-536SD, FS-537, or FS-537SD is installed> • RU transport sensor (PS60) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed: 1 Initial check items - - 2 PS60 I/O check, sensor check FSCB J6-7 (ON) FS-536/FS-536SD 12-K 3 Replace FSCB. (b) When FS-537 or FS-537SD is installed: 1 Initial check items - - 2 PS60 I/O check, sensor check FSCB J8<B>-15 (ON) FS-537/FS-537SD 9-D 3 Replace FSCB. |
| Error code: | 92-01 |
| Description: | The registration sensor (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after a duplex paper feed sequence has been started. |
| Causes: | • Transport motor (M1) • ADU transport clutch (CL6) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 92-02 |
| Description: | For the second-side feed of paper in the duplex mode, loop forming has not been complete before the second side of a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop. |
| Causes: | • Transport motor (M1) • ADU transport clutch (CL6) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 92-40 |
| Description: | For the second-side feed of paper in the duplex mode, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. |
| Causes: | • Transport motor (M1) • ADU transport clutch (CL6) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) |
| Error code: | 93-10 |
| Description: | Misfeed at duplex transport section. The ADU paper passage sensor/2 (PS48) is not turned ON (unblocked) even after the set period of time has elapsed after the ADU paper passage sensor/1 (PS47) turns ON (block) by the paper. - Paper jam of a sheet of paper left at the duplex transport section results, if the ADU paper passage sensor/1 (PS47) is turned ON (blocked) or the ADU paper passage sensor/2 (PS48) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - When the main power switch is turned ON, residual paper detection starts between each sensor. Paper jam of a sheet of paper left at the duplex transport section results, if the the ADU paper passage sensor/1 (PS47) is turned from OFF (unblocked) to ON (blocked). - When the main power switch is turned ON, residual paper detection starts between each sensor. Paper jam of a sheet of paper left at the duplex transport section results, if the ADU paper passage sensor/2 (PS48) is turned from OFF (blocked) to ON (unblocked). |
| Causes: | • ADU transport motor/1 (M31) • ADU transport motor/2 (M32) • ADU paper passage sensor/1 (PS47) • ADU paper passage sensor/2 (PS48) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Initial check items - - 2 PS47 I/O check, sensor check PFTDB CN28-3 (ON) 7-P 3 PS48 I/O check, sensor check PFTDB CN28-6 (ON) 6-P 4 M31 operation check PFTDB CN28-14 to 17 8-P 5 M32 operation check PFTDB CN28-10 to 13 7-P 6 PFTDB F10 conduction check - - 7 Replace PFTDB. - - 8 Replace MFPB. |
| Error code: | 99-01 |
| Description: | Controller JAM (paper size error). • As a result of a paper size error, the controller transmits a forced stop command to the printer engine and the printer engine is internally processing the size error. • As a result of a paper size error, the controller transmits a forced stop command to the printer engine; but the paper causing the size error cannot be fed out. |
| Remedy: | 1 Initial check items - - 2 Open and close the front door of the main body. |
| Error code: | 99-02 |
| Description: | Controller JAM (controller forced stop command). The controller transmits a forced stop command under a condition other than a paper size error during a print cycle. |
| Remedy: | 1 Initial check items - - 2 Open and close the front door of the main body. |
| Error code: | 99-03 |
| Description: | Controller JAM (image processing). Image stabilization not completing a job. |
| Remedy: | 1 Initial check items - - 2 Open and close the front door of the main body. |
| Error code: | 99-04 |
| Description: | Controller JAM (a job reservation in the main body is not released). A job reservation is not released after a lapse of a given time after that a print start command has been received. |
| Remedy: | 1 Initial check items - - 2 Open and close the front door of the main body. |
| Error code: | 99-05 |
| Description: | Controller JAM (main body not starting a job). A waiting status is not released even with a print start command received. |
| Remedy: | 1 Initial check items - - 2 Open and close the front door of the main body. |
| Error code: | 99-06 |
| Description: | Controller JAM (print control on the main body is not completed). Print control is not completed even after a job has been completed. |
| Remedy: | 1 Initial check items - - 2 Open and close the front door of the main body. |
| Error code: | 99-07 |
| Description: | Controller JAM (main body not completing a job). The engine does not stop after a lapse of a given time after that a print has finished. |
| Remedy: | 1 Initial check items - - 2 Open and close the front door of the main body. |
| Error code: | 99-08 |
| Description: | Controller JAM (finisher not starting a job). The finisher does not accept a print start command. |
| Remedy: | 1 Initial check items - - 2 Open and close the front door of the main body. Or, open and close the front door of the finisher. |
| Error code: | 99-09 |
| Description: | Controller JAM (finisher not completing a job). • A paper exit or paper finishing process inside the finisher is not completed. • The finisher does not start during a reset procedure from the jam. |
| Remedy: | 1 Initial check items - - 2 Open and close the front door of the main body. Or, open and close the front door of the finisher. |
| Error code: | C0002 |
| Description: | Paper feed communication error. When the paper feed/transport drive board (PFTDB) is receiving data, a communication error is detected. |
| Causes: | • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Correct the harness connection between MFPB CN7E-PFTDB CN4 if faulty. 3. Rewrite the firmware. 4. PFTDB F3 conduction check 5. Replace PFTDB. 6. MFPB F2E conduction check 7. Replace MFPB. |
| Error code: | C0106 |
| Description: | Tray 3/LCT paper feed motor turning at abnormal timing • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | <When PC-110 or PC-210 is installed> • Tray 3 paper feed motor (M111) • PC control board (PCCB) <When PC-410 is installed> • Paper feed motor (M131) • PC control board (PCCB) |
| Remedy: | When PC-110 or PC-210 is installed: 1 Check the connector between M111-PCCB CN5 for proper connection and correct as necessary. 2 Check the connector of M111 for proper drive coupling and correct as necessary. 3 M111 operation check PCCB CN5-5 (CW/CCW) PC-110/PC-210 4-C. 4 Replace M111. 5 Replace PCCB. When PC-410 is installed: 1 Check the connector between M131-PCCB CN5 for proper connection and correct as necessary. 2 Check the connector of M131 for proper drive coupling and correct as necessary. 3 M131 operation check PCCB CN5-5 (CW/CCW) PC-410 5-J 4 Replace M131. 5 Replace PCCB. |
| Error code: | C0107 |
| Description: | Tray 3/LCT vertical transport motor turning at abnormal timing • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | <When PC-110 or PC-210 is installed> • Tray 3 vertical transport motor (M112) • PC control board (PCCB) <When PC-410 is installed> • Vertical transport motor (M132) • PC control board (PCCB) |
| Remedy: | When PC-110 or PC-210 is installed: 1 Check the connector between M112-PCCB CN5 for proper connection and correct as necessary. 2 Check the connector of M112 for proper drive coupling and correct as necessary. 3 M112 operation check PCCB CN5-13 (CW/CCW) PC-110/PC-210 3 to 4-C. 4 Replace M112. 5 Replace PCCB. When PC-410 is installed: 1 Check the connector between M132-PCCB CN5 for proper connection and correct as necessary. 2 Check the connector of M132 for proper drive coupling and correct as necessary. 3 M132 operation check PCCB CN5-13 (CW/CCW) PC-410 4-J. 4 Replace M132. 5 Replace PCCB. |
| Error code: | C0108 |
| Description: | Tray 4 paper feed motor turning at abnormal timing <When PC-210 is installed> • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Tray 4 paper feed motor (M121) • PC control board (PCCB) |
| Remedy: | 1 Check the connector between M121-PCCB CN9 for proper connection and correct as necessary. 2 Check the connector of M121 for proper drive coupling and correct as necessary. 3 M121 operation check PCCB CN9-5 (CW/CCW) PC-210 6-K. 4 Replace M121. 5 Replace PCCB |
| Error code: | C0109 |
| Description: | Tray 4 vertical transport motor turning at abnormal timing <When PC-210 is installed> • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Tray 4 vertical transport motor (M122) • PC control board (PCCB) |
| Remedy: | 1 Check the connector between M122-PCCB CN9 for proper connection and correct as necessary. 2 Check the connector of M122 for proper drive coupling and correct as necessary. 3 M122 operation check PCCB CN9-13 (CW/CCW) PC-210 6-K. 4 Replace M122. 5 Replace PCCB. |
| Error code: | C0202 |
| Description: | Magenta PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 1 upper limit sensor (PS6) • Tray 1 lift-up motor (M6) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0204 |
| Description: | Yellow PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 2 upper limit sensor (PS14) • Tray 2 lift-up motor (M8) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0206 |
| Description: | Black PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 3 upper limit sensor (PS22) • Tray 3 lift-up motor (M23) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0208 |
| Description: | Tray 5 feeder up/down abnormality |
| Causes: | • Tray 4 upper limit sensor (PS27) • Tray 4 lift-up motor (M24) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0211 |
| Description: | Tray 1 feeder up/down abnormality • The paper feed tray 1 lift-up position sensor is not unblocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The paper feed tray 1 lift-up position sensor is not blocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started. |
| Causes: | • Bypass lift-up motor (M26) • Bypass upper limit sensor (PS35) • Bypass lower limit sensor (PS36) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check the connector of M1 for proper drive coupling and correct as necessary. 3 PS17 I/O check PRCB CN6PRCB-7 (ON) D-2. 4 SL1 operation check PRCB CN6PRCB-4 (ON) D-1. 5 M1 operation check PRCB CN34PRCB-10 (REM) PRCB CN34PRCB-13 (LOCK) D-22. 6 Change SL1. 7 Change M1. 8 Change PRCB. |
| Error code: | C0214 |
| Description: | LCT shifting failure |
| Causes: | • Shifter motor (M133) • Shifter stop / lower limit position sensor (PS138) • Shifter home sensor (PS139) • PC control board (PCCB) |
| Error code: | C0216 |
| Description: | LCT up/down abnormality (When LU-205 or LU-303 is installed). The LU upper limit sensor (PS2) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began. |
| Causes: | • LU upper limit sensor (PS2) • LU lift-up motor (M1) • LU drive board (LUDB) |
| Remedy: | 1. Check the connector between M1-LUDB CN3 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-relay CN406-LUDB CN5 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: LUDB CN5-3 (ON) • Location of electrical component: LU-205/LU-303 4-G 5. M1 operation check • Control signal: LUDB CN3-4 (ON) • Location of electrical component: LU-205/LU-303 3-G 6. Replace M1. 7. Replace LUDB. (LU-205/LU-303) NOTICE • Link to the wiring diagram ( N.3.1 LU-205) • Link to the wiring diagram ( N.3.2 LU-303) |
| Error code: | C1004 |
| Description: | FNS communication error |
| Causes: | FS control board (FSCB) |
| Error code: | C1081 |
| Description: | SD communication error <When FS-534+SD-511 is installed> When a communication error is detected between the FS control board (FSCB) and the SD control board (SDDB). |
| Causes: | • SD drive board (SDDB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace SDDB. 4 Replace FSCB. |
| Error code: | C1102 |
| Description: | Main tray up/down motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • While the exit tray is being lifted, the main tray upper position sensor (PS26/PS27) is not turned ON (blocked) and the main tray upper position detect switch (SW2) is not turned ON, even after the main tray up/down motor (M11) turns by the set number of times. • While the exit tray is being lowered, the main tray full detection sensor (PS29) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M11) is turned ON. <When FS-537 or FS-537SD is installed> • The main tray lift up detection sensor (PS16/PS17) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/ down motor (M6) is turned ON. • The main tray full detection sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M6) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Main tray up/down motor (M11) • Main tray upper position sensor/R (PS26) • Main tray upper position sensor/F (PS27) • Main tray full detection sensor (PS29) • Main tray upper position detect switch (SW2) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Main tray up/down motor (M6) • Main tray lift up detection sensor/F (PS16) • Main tray lift up detection sensor/R (PS17) • Main tray full detection sensor (PS12) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M11-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M11 for proper drive coupling, and correct as necessary. 3. Check the connector between PS26-relay CN1-FSCB J14 for proper connection and correct as necessary. 4. Check the connector between PS27-relay CN1-FSCB J14 for proper connection and correct as necessary. 5. Check the connector between PS29-relay CN2-FSCB J14 for proper connection and correct as necessary. 6. Check the connector between SW2-FSCB J10 for proper connection and correct as necessary. 7. PS26 I/O check, sensor check • Control signal: FSCB J14<A>-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-C 8. PS27 I/O check, sensor check • Control signal: FSCB J14<B>-6 (ON) • Location of electrical component: FS-536/FS-536SD 3-C 9. PS29 I/O check, sensor check • Control signal: FSCB J14<A>-8 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 10. SW2 operation check • Control signal: FSCB J10-1 to 2 • Location of electrical component: FS-536/FS-536SD 15-K 11. M11 operation check • Control signal: FSCB J9<A>-9 to 10 • Location of electrical component: FS-536/FS-536SD 12-C 12. Replace M11. 13. FSCB F2 conduction check 14. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M6-FSCB J23 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS16-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 4. Check the connector between PS17-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 5. Check the connector between PS12-relay CN9-FSCB J19 for proper connection and correct as necessary. 6. PS16 I/O check, sensor check • Control signal: FSCB J20<B>-4 (ON) • Location of electrical component: FS-537/FS-537SD 11 to 12-D 7. PS17 I/O check, sensor check • Control signal: FSCB J20<B>-7 (ON) • Location of electrical component: FS-537/FS-537SD 12-D 8. PS12 I/O check, sensor check • Control signal: FSCB J19-7 (ON) • Location of electrical component: FS-537/FS-537SD 10-D 9. M6 operation check • Control signal: FSCB J23-1 to 11 • Location of electrical component: FS-537/FS-537SD 13-D 10. Replace M6. 11. FSCB F3 conduction check 12. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1103 |
| Description: | Alignment motor/Front’s drive malfunction. <When FS-536 or FS-536SD is installed> • The alignment plate/F home sensor (PS12) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M7) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. <When FS-537 or FS-537SD is installed> • The alignment plate/F home sensor (PS9) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS9) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M14) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. |
| Causes: | <When FS-536 or FS-536SD is installed> • Alignment motor/Front (M7) • Alignment plate/F home sensor (PS12) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Alignment motor/Front (M14) • Alignment plate/F home sensor (PS9) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M7-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS12-FSCB J4 for proper connection and correct as necessary. 4. PS12 I/O check, sensor check • Control signal: FSCB J4<B>-4 (ON) • Location of electrical component: FS-536/FS-536SD 15-C 5. M7 operation check • Control signal: FSCB J4<A>-5 to 8 • Location of electrical component: FS-536/FS-536SD 14-C 6. Replace M7. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M14-relay CN5-FSCB J18 for proper connection and correct as necessary. 2. Check the connector of M14 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-relay CN5-FSCB J18 for proper connection and correct as necessary. 4. PS9 I/O check, sensor check • Control signal: FSCB J18-10 (ON) • Location of electrical component: FS-537/FS-537SD 6-D 5. M14 operation check • Control signal: FSCB J18-1 to 4 • Location of electrical component: FS-537/FS-537SD 6-D 6. Replace M14. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1105 |
| Description: | Bundle eject motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • The gripper home position sensor (PS18) is not turned ON (unblocked) even after the set period of time has elapsed after the gripper position detection sensor (PS19) turns OFF (block). • The gripper position detection sensor (PS19) is not turned OFF (blocked) even after the set period of time has elapsed after PS19 turns ON (unblock). • The gripper position detection sensor (PS19) is not turned ON (unblocked) even after the set period of time has elapsed after the gripper home position sensor (PS18) turns OFF (block). • The gripper home position sensor (PS18) is not turned OFF (blocked) even after the set period of time has elapsed after the bundle eject motor (M10) is energized. • The gripper home position sensor (PS18) and the gripper position detection sensor (PS19) is turned ON (unblocked) at the same time. <When FS-537 or FS-537SD is installed> The gripper home position sensor (PS3) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed after the bundle eject motor (M1) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Bundle eject motor (M10) • Gripper home position sensor (PS18) • Gripper position detection sensor (PS19) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Bundle eject motor (M1) • Gripper home position sensor (PS3) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M10-relay CN7<A>-FSCB J13 for proper connection and correct as necessary. 2. Check the connector of M10 for proper drive coupling, and correct as necessary. 3. Check the connector between PS18-relay CN7<A>-FSCB J13 for proper connection and correct as necessary. 4. Check the connector between PS19-relay CN8<B>-FSCB J12 for proper connection and correct as necessary. 5. PS18 I/O check, sensor check • Control signal: FSCB J13-13 (ON) • Location of electrical component: FS-536/FS-536SD 8-C 6. PS19 I/O check, sensor check • Control signal: FSCB J12-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 7. M10 operation check • Control signal: FSCB J13-1 to 2 • Location of electrical component: FS-536/FS-536SD 9-C 8. Replace M10. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M1-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS3-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 4. PS3 I/O check, sensor check • Control signal: FSCB J22<A>-13 (ON) • Location of electrical component: FS-537/FS-537SD 2-D 5. M1 operation check • Control signal: FSCB J22<A>-1 to 2 • Location of electrical component: FS-537/FS-537SD 1-D 6. Replace M1. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1106 |
| Description: | Stapler movement motor’s malfunction. <When FS-536 or FS-536SD is installed> • The stapler home position sensor (rear) (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the side stapler movement motor (M13) turned ON. • The stapler does not reach the specified position within the set period of time. <When FS-537 or FS-537SD is installed> • The stapler home position sensor (PS18/PS19) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler movement motor (M19) turned ON. • The stapler does not reach the specified position within the set period of time. |
| Causes: | <When FS-536 or FS-536SD is installed> • Side stapler movement motor (M13) • Stapler home position sensor (rear) (PS23) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler movement motor (M19) • Stapler home position sensor (corner) (PS18) • Stapler home position sensor (rear) (PS19) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M13-relay CN3-FSCB J11 for proper connection, and correct as necessary. 2. Check the connector of M13 for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 5. M13 operation check • Control signal: FSCB J11<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 4-C 6. Replace M13. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M19-FSCB J17 for proper connection and correct as necessary. 2. Check the connector of M19 for proper drive coupling and correct as necessary. 3. Check the connector between PS18-FSCB J16 for proper connection and correct as necessary. 4. Check the connector between PS19-FSCB J16 for proper connection and correct as necessary. 5. PS18 I/O check, sensor check • Control signal: FSCB J16-9 (ON) • Location of electrical component: FS-537/FS-537SD15-D 6. PS19 I/O check, sensor check • Control signal: FSCB J16-6 (ON) • Location of electrical component: FS-537/FS-537SD 15-D 7. M19 operation check • Control signal: FSCB J17-10 to 13 • Location of electrical component: FS-537/FS-537SD 14-D 8. Replace M19. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1109 |
| Description: | Stapler motor’s malfunction. <When FS-536 or FS-536SD is installed> • The stapler home position sensor (rear) (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler motor (M14) turned ON. • The stapler position sensor (center) (PS24) is turned ON (blocked), when the stapler motor (M14) is running. <When FS-537 or FS-537SD is installed> • The stapler home position sensor (PS18/PS19) is not turned (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler movement motor (M5) turned ON. • The stapler position sensor (center) (PS20) is turned ON (blocked), when the stapler motor (M5) is running. |
| Causes: | <When FS-536 or FS-536SD is installed> • Stapler unit • Stapler home position sensor (rear) (PS23) • Stapler position sensor (center) (PS24) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler unit • Stapler home position sensor (corner) (PS18) • Stapler home position sensor (rear) (PS19) • Stapler position sensor (center) (PS20) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between the stapler unit-relay CN4-FSCB J11 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. Check the connector between PS24-relay CN3-FSCB J11 for proper connection and correct as necessary. 5. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 6. PS24 I/O check, sensor check • Control signal: FSCB J11<B>-6 • Location of electrical component: FS-536/FS-536SD 5-C 7. Replace the stapler unit. 8. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between the stapler unit-FSCB J17 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS18-FSCB J16 for proper connection and correct as necessary. 4. Check the connector between PS19-FSCB J16 for proper connection and correct as necessary. 5. Check the connector between PS20-FSCB J16 for proper connection and correct as necessary. 6. PS18 I/O check, sensor check • Control signal: FSCB J16-9 • Location of electrical component: FS-537/FS-537SD 15-D 7. PS19 I/O check, sensor check • Control signal: FSCB J16-6 • Location of electrical component: FS-537/FS-537SD 15-D 8. PS20 I/O check, sensor check • Control signal: FSCB J16-3 • Location of electrical component: FS-537/FS-537SD 15-D 9. Replace the stapler unit. 10. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1112 |
| Description: | Stapler motor`s drive malfunction. <When FS-536SD or FS-537SD is installed> • The stapler home sensor is not turned ON even after the set period of time has elapsed while the stapler motor is energized. • The stapler home sensor is not turned OFF even after the set period of time has elapsed after the stapler home sensor is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Staple unit • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between the staple unit-SDCB J4 for proper connection and correct as necessary. 2. Check the connector of the staple unit for proper drive coupling and correct as necessary. 3. Replace the staple unit. (FS-536SD/FS-537SD) 4. Replace SDCB. (FS-536SD/FS-537SD) 5. Replace FSCB. (FS-536SD/FS-537SD) |
| Error code: | C1113 |
| Description: | Stopper drive motor`s malfunction. <When FS-536SD or FS-537SD is installed> The stopper home sensor (PS6) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stopper drive motor (M4) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Stopper drive motor (M4) • Stopper home sensor (PS6) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M4-SDCB J10 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-SDCB J10 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: SDCB J10-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 2-P 5. M4 operation check • Control signal: SDCB J10-6 to 9 • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 1-P 6. Replace M4. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1114 |
| Description: | Alignment motor’s malfunction. <When FS-536SD or FS-537SD is installed> The alignment home sensor (PS4) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the alignment motor (M3) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Alignment motor (M3) • Alignment home sensor (PS4) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M3-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS4-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS4 I/O check, sensor check • Control signal: SDCB J7-6 (ON) • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 5. M3 operation check • Control signal: SDCB J7-7 to 10 • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 6. Replace M3. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1115 |
| Description: | Center fold knife motor`s malfunction. <When FS-536SD or FS-537SD is installed> The center fold knife home sensor (PS8) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Center fold knife motor (M9) • Center fold knife home sensor (PS8) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M9-SDCB J11 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS8-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS8 I/O check, sensor check • Control signal: SDCB J7-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-P, FS-537/FS-537SD 6-P 5. M9 operation check • Control signal: SDCB J11-11 to 20 • Location of electrical component: FS-536/FS-536SD 2-L, FS-537/FS-537SD 1-K 6. Replace M9. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1132 |
| Description: | Punch drive motor’s drive malfunction. <When FS-536+PK-520 or FS-536SD+PK-520 is installed> The punch home sensor (PS1) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the punch drive motor (M1) is energized. <When FS-537+PK-523 or FS-537SD+PK-523 is installed> The PK punch home sensor/2(PS301) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the punch drive motor (M301) is energized. |
| Causes: | <When FS-536+PK-520 or FS-536SD+PK-520 is installed> • Punch drive motor (M1) • Punch home sensor (PS1) • FS control board (FSCB) <When FS-537+PK-523 or FS-537SD+PK-523 is installed> • Punch drive motor (M301) • PK punch home sensor/2(PS301) • Punch control board (PKCB) • FS control board (FSCB) |
| Remedy: | (a) When FS-536+PK-520 or FS-536SD+PK-520 is installed 1. Check the connector between M1-relay CN351-FSCB J7 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS1-FSCB J7 for proper connection and correct as necessary. 4. PS1 I/O check, sensor check • Control signal: FSCB J7-5 (ON) • Location of electrical component: FS-536/FS-536SD 13-K 5. M1 operation check • Control signal: FSCB J7-7 to 8 • Location of electrical component: FS-536/FS-536SD 13-K 6. Replace M1. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537+PK-523 or FS-537SD+PK-523 is installed 1. Check the connector between M301-relay CN351-PKCB CN35 for proper connection and correct as necessary. 2. Check the connector of M301 for proper drive coupling and correct as necessary. 3. Check the connector between PS301-PKCB CN36 for proper connection and correct as necessary. 4. PS301 I/O check, sensor check • Control signal: PKCB CN36-5 (ON) • Location of electrical component: PK-523 3-C 5. M301 operation check • Control signal: PKCB CN35-1 to 3 • Location of electrical component: PK-523 2-C 6. Replace M301. 7. Replace PKCB. 8. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.4 PK-523) |
| Error code: | C1140 |
| Description: | PF lift motor error Object: Side feeder |
| Causes: | 1. The PF lift upper limit sensor does not turn on when passing 30s after cassette 5 is inserted. 2. The lock-up signal is detected for 200ms continuously during the PF lift motor operation. 3. The PF lift upper limit sensor does not turn on when passing 2s after the upper limit control when printing starts. |
| Remedy: | 1 Checking the bottom plate The bottom plate does not operate properly. Repair or replace the bottom plate when it does not move vertically. 2 Checking the drive gear The drive gear to lift up the bottom plate does not rotate properly. Check if the drive gears to lift up the bottom plate rotate smoothly or have no excessive load. And apply the grease to the frictional parts and fix the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor - PF main PWB Wiring diagram 4 Checking the PF lift motor The PF lift motor is faulty. Replace the PF lift motor. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift upper limit sensor - PF main PWB Wiring diagram 6 Checking the PF lift upper limit sensor The PF lift upper limit sensor is not properly attached or faulty. Reattach the PF lift upper limit sensor. Then, replace it if it is not fixed. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1141 |
| Description: | FNS paddle motor’s malfunction. <When FS-536 or FS-536SD is installed> The upper paddle home position detection sensor (PS14) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M5) is turning. <When FS-537 or FS-537SD is installed> The paddle home sensor (PS25) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M9) is turning. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS paddle motor (M5) • Upper paddle home position detection sensor (PS14) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • FNS paddle motor (M9) • Paddle home sensor (PS25) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M5-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS14-FSCB J4 for proper connection and correct as necessary. 4. PS14 I/O check, sensor check • Control signal: FSCB J4<B>-7 (ON) • Location of electrical component: FS-536/FS-536SD 15-C 5. M5 operation check • Control signal: FSCB J4<A>-9 to 12 • Location of electrical component: FS-536/FS-536SD 14-C 6. Replace M5. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M9-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS25-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 4. PS25 I/O check, sensor check • Control signal: FSCB J14<B>-10 (ON) • Location of electrical component: FS-537/FS-537SD 16-K to L 5. M9 operation check • Control signal: FSCB J14<B>-4 to 7 • Location of electrical component: FS-537/FS-537SD 17- K to L 6. Replace M9. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1144 |
| Description: | Pre-eject drive motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • The pre-eject home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the preeject drive motor (M9) is turned ON. • The pre-eject away sensor (PS22) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the preeject drive motor (M9) is turned ON. <When FS-537 or FS-537SD is installed> The trail edge stopper home sensor (PS31) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the pre-eject drive motor (M2) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Pre-eject drive motor (M9) • Pre-eject home sensor (PS21) • Pre-eject away sensor (PS22) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Pre-eject drive motor (M2) • Trail edge stopper home sensor (PS31) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M9-relay CN7<A>-FSCB J13 for proper connection, and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 4. Check the connector between PS22-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 5. PS21 I/O check, sensor check • Control signal: FSCB J12-6 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 6. PS22 I/O check, sensor check • Control signal: FSCB J12-9 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 7. M9 operation check • Control signal: FSCB J13-3 to 4 • Location of electrical component: FS-536/FS-536SD 9-C 8. Replace M9. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M2-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS31-relay CN2-relay CN1<B>-FSCB J22 for proper connection and correct as necessary. 4. PS31 I/O check, sensor check • Control signal: FSCB J22<B>-13 • Location of electrical component: FS-537/FS-537SD 3-D 5. M2 operation check • Control signal: FSCB J22<A>-3 to 4 • Location of electrical component: FS-537/FS-537SD 1-D 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1145 |
| Description: | Trailing edge stopper motor malfunction. <When FS-536 or FS-536SD is installed> The trailing edge stopper home position detection sensor (PS20) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the trailing edge stopper motor (M6) is turned ON. <When FS-537 or FS-537SD is installed> The trailing edge stopper home position detection sensor/F (PS10) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the trailing edge stopper motor/F (M12) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Trailing edge stopper motor (M6) • Trailing edge stopper home position detection sensor (PS20) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Trail edge stopper motor/F (M12) • Trail edge stopper sensor/F (PS10) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M6-FSCB J5 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS20-relay CN19-FSCB J5 for proper connection and correct as necessary. 4. PS20 I/O check, sensor check • Control signal: FSCB J5-9 (ON) • Location of electrical component: FS-536/FS-536SD 15-K 5. M6 operation check • Control signal: FSCB J5-13 to 16 • Location of electrical component: FS-536/FS-536SD 15-K 6. Replace M6. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M12-relay CN5-FSCB J18 for proper connection and correct as necessary. 2. Check the connector of M12 for proper drive coupling and correct as necessary. 3. Check the connector between PS10-relay CN5-FSCB J18 for proper connection and correct as necessary. 4. PS10 I/O check, sensor check • Control signal: FSCB J18-13 (ON) • Location of electrical component: FS-537/FS-537SD 6 to 7-D 5. M12 operation check • Control signal: FSCB J18-14 to 17 • Location of electrical component: FS-537/FS-537SD 7-D 6. Replace M12. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1156 |
| Description: | SD paddle motor malfunction. <When FS-536SD or FS-537SD is installed> The paddle home sensor (PS5) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the SD paddle motor (M7) is turning. |
| Causes: | <When FS-536SD or FS-537SD is installed> • SD paddle motor (M7) • Paddle home sensor (PS5) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M7-SDCB J8 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS5-SDCB J8 for proper connection and correct as necessary. 4. PS5 I/O check, sensor check • Control signal: SDCB J8-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 5. M7 operation check • Control signal: SDCB J8-4 to 7 • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 6. Replace M7. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1182 |
| Description: | Unsupported option trouble |
| Causes: | When JS-504 is installed: Shift motor (M2) Shift home sensor (PS6) JS control board (JSCB). When FS-527 is installed: Tray2 shift motor (M16) Tray2 shift home sensor (PS25) FS control board (FSCB) |
| Error code: | C1184 |
| Description: | Paper discharge control motor malfunction. <When FS-536 or FS-536SD is installed> The paper delivery control sensor (PS28) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed while the paper receiving control motor (M12) is energized. <When FS-537 or FS-537SD is installed> The paper delivery control sensor (PS11) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed while the paper receiving control motor (M15) is energized. |
| Causes: | <When FS-536 or FS-536SD is installed> • Paper receiving control motor (M12) • Paper delivery control sensor (PS28) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Paper receiving control motor (M15) • Paper delivery control sensor (PS11) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M12-relay CN1-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M12 for proper drive coupling and correct as necessary. 3. Check the connector between PS28-relay CN1-FSCB J14 for proper connection and correct as necessary. 4. PS28 I/O check, sensor check • Control signal: FSCB J14<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 2 to 3-C 5. M12 operation check • Control signal: FSCB J14<A>-9 to 12 • Location of electrical component: FS-536/FS-536SD 2-C 6. Replace M12. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M15-FSCB J19 for proper connection and correct as necessary. 2. Check the connector of M15 for proper drive coupling and correct as necessary. 3. Check the connector between PS11-relay CN10<A>-FSCB J20 for proper connection and correct as necessary. 4. PS11 I/O check, sensor check • Control signal: FSCB J20<A>-3 (ON) • Location of electrical component: FS-537/FS-537SD 10-D 5. M15 operation check • Control signal: FSCB J19-1 to 4 • Location of electrical component: FS-537/FS-537SD 10-D 6. Replace M15. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1195 |
| Description: | Paper discharge control motor malfunction. <When FS-536SD or FS-537SD is installed> The curl cover detection sensor (PS2) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the paper discharge control motor (M2) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Paper discharge control motor (M2) • Curl cover detection sensor (PS2) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M2-relay CN22 (FS-536SD), CN25 (FS-537SD)-relay CN21 (FS-536SD), CN26 (FS-537SD)-SDCB J5 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-relay CN22 (FS-536SD), CN25 (FS-537SD)-relay CN21 (FS-536SD), CN26 (FS-537SD)-SDCB J5 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: SDCB J5-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-L, FS-537/FS-537SD 3-K 5. M2 operation check • Control signal: SDCB J5-4 to 7 • Location of electrical component: FS-536/FS-536SD 4-L, FS-537/FS-537SD 3-K 6. Replace M2. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1196 |
| Description: | Center fold guide motor’s drive malfunction. <When FS-536SD or FS-537SD is installed> The guide home sensor (PS7) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the center fold roller motor (M6) is turned ON. |
| Causes: | <When FS-536SD is installed> <When FS-537SD is installed> • Center fold guide motor (M6) • Guide home sensor (PS7) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M6-SDCB J9 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS7-SDCB J9 for proper connection and correct as necessary. 4. PS7 I/O check, sensor check • Control signal: SDCB J9-6 (ON) • Location of electrical component: FS-536/FS-536SD 5-P, FS-537/FS-537SD 4-P 5. M6 operation check • Control signal: SDCB J9-7 to 10 • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 4-P 6. Replace M6. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1197 |
| Description: | Tri-folding guide motor’s drive malfunction. <When FS-536SD or FS-537SD is installed> The tri-folding gate home sensor (PS11) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the tri-folding guide motor (M8) is energized. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Tri-folding guide motor (M8) • Tri-folding gate home sensor (PS11) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M8-SDCB J8 for proper connection and correct as necessary. 2. Check the connector of M8 for proper drive coupling and correct as necessary. 3. Check the connector between PS11-SDCB J8 for proper connection and correct as necessary. 4. PS11 I/O check, sensor check • Control signal: SDCB J8-10 (ON) • Location of electrical component: FS-536/FS-536SD 3-P, FS-537/FS-537SD 3-P 5. M8 operation check • Control signal: SDCB J8-11 to 14 • Location of electrical component: FS-536/FS-536SD 3-P, FS-537/FS-537SD 2-P 6. Replace M8. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C11A1 |
| Description: | Finishing option exit roller pressure/retraction failure |
| Causes: | Exit roller retraction motor (M9) Exit roller pressure sensor (PS12) FS control board (FSCB) |
| Error code: | C11A2 |
| Description: | Saddle exit roller pressure/retraction failure |
| Causes: | <When FS-536 or FS-536SD is installed> • Receiving roller retraction motor (M4) • Receiving roller retraction sensor (PS11) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Receiving roller retraction motor (M10) • Receiving roller retraction sensor (PS22) • FS control board (FSCB) |
| Error code: | C11E1 |
| Description: | Paper exit switching drive malfunction. <When FS-536 or FS-536SD is installed> The exchange folded paper output sensor (PS30) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the FNS entry transport motor (M2) is turned ON. <When FS-537 or FS-537SD is installed> The route change gate home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the route change gate motor (M4) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS entry transport motor (M2) • Exchange folded paper output sensor (PS30) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Route change gate motor (M4) • Route change gate home sensor (PS21) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M2-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS30-FSCB J4 for proper connection and correct as necessary. 4. PS30 I/O check, sensor check • Control signal: FSCB J4<A>-15 (ON) • Location of electrical component: FS-536/FS-536SD 14-C 5. M2 operation check • Control signal: FSCB J9<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 12-C 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M4-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-FSCB J12 for proper connection and correct as necessary. 4. PS21 I/O check, sensor check • Control signal: FSCB J12<B>-12 (ON) • Location of electrical component: FS-537/FS-537SD 18-D 5. M4 operation check • Control signal: FSCB J21<B>-8 to 9 • Location of electrical component: FS-537/FS-537SD 18-D 6. Replace M4. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1402 |
| Description: | IR illegal interrupt vector occurred |
| Causes: | FS control board (FSCB) |
| Remedy: | 1. Reset the malfunction. 2. If the same malfunction persists, change the Image Processing Board. |
| Error code: | C2152 ... C2156 |
| Description: | • C2152: Transfer belt fault at initial position return • C2153: Transfer belt spacing fault at K pressure switching • C2154: Transfer belt contact fault at all pressure switching • C2155: Transfer belt contact fault after K pressure established • C2156: Transfer belt spacing fault after all pressure established. • C2152: The 1st transfer pressure sensor (PS39) is unable to detect "switch from retraction to pressure" or "switch from pressure to retraction" within a given period time after the 1st transfer pressure clutch (CL5) has stared engagement during an initial position return. • C2153: The 1st transfer pressure sensor (PS39) does not detect “switch from pressure to retraction” within a given period time after 1st transfer pressure clutch (CL5) has stared engagement. • C2154: The 1st transfer pressure sensor (PS39) does not detect “switch from retraction to pressure” within a given period time after 1st transfer pressure clutch (CL5) has stared engagement. • C2155: The 1st transfer pressure sensor (PS39) is blocked after the lamps of given time after the 1st transfer pressure clutch (CL5) turned OFF when the release operation is finished. • C2156: The 1st transfer pressure sensor (PS39) is unblocked after the laps of given time after the 1st transfer pressure clutch (CL5) turned OFF when the pressing operation is finished. |
| Causes: | • Fusing motor (M3) • 1st transfer pressure clutch (CL5) • 1st transfer pressure sensor (PS39) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M3-MFPB CN8E for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS39-relay CN113-MFPB CN15EB for proper connection and correct as necessary. 4. Check the connector between CL5-relay CN118-MFPB CN15EA for proper connection and correct as necessary. 5. PS39 I/O check, sensor check • Control signal: MFPB CN15EB-17 (ON) • Location of electrical component: 10-C 6. CL5 operation check • Control signal: MFPB CN15EA-18 (ON) • Location of electrical component: 8-C 7. M3 operation check • Control signal: MFPB CN8E-9 (REM), MFPB CN8E-12 (LOCK) • Location of electrical component: 2-C 8. Replace M3. 9. MFPB ICP2E conduction check 10. Replace MFPB. |
| Error code: | C2253, C2254 |
| Description: | • C2253: PC motor/YMC failure to turn • C2254: PC motor/YMC turning at abnormal timing • C2253: The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. • C2254: The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Imaging unit/C • Imaging unit/M • Imaging unit/Y • PC motor/YMC (M16) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M16-MFPB CN10E, CN16E for proper connection and correct as necessary. 2. Check the connector of M16 for proper drive coupling and correct as necessary. 3. M16 load check • Check code: 41 • Multi code: 2, 3, 4 • Control signal: MFPB CN10E<B>-3 (REM), MFPB CN10E<B>-6 (LOCK), MFPB CN16E-3 (DC24V) • Location of electrical component: 5-K 4. Replace M16. 5. Replace the imaging unit/Y,M,C. 6. MFPB F9E conduction check 7. Replace MFPB. |
| Error code: | C2255, C2256 |
| Description: | • C2255: Developing motor/YMC failure to turn • C2256: Developing motor/YMC turning at abnormal timing • C2255: The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. • C2256: The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Imaging unit/C • Imaging unit/M • Imaging unit/Y • Developing motor/YMC (M17) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M17-MFPB CN10E, CN16E for proper connection and correct as necessary. 2. Check the connector of M17 for proper drive coupling and correct as necessary. 3. M17 load check • Check code: 50 • Multi code: 2, 3, 4 • Control signal: MFPB CN16E-1 (DC24V), MFPB CN10E<B>-9 (START/STOP) • Location of electrical component: 6-K 4. Replace M17. 5. Replace the imaging unit/Y,M,C. 6. MFPB F9E conduction check 7. Replace MFPB. |
| Error code: | C2355 |
| Description: | Transfer belt cleaner cooling fan motor’s failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Transfer belt cleaner cooling fan (FM2) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between FM2-relay CN115- PRCB CN13 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM2 operation check PRCB CN13-8 (REM) PRCB CN13-10 (LOCK) 24-C. 4 Replace FM2. 5 PRCB ICP3 conduction check. 6 Replace PRCB. |
| Error code: | C2411, C2412 |
| Description: | • C2411: Developing unit/C new article release • C2412: Developing unit/M new article release. The status with the new unit is not cleared after the new developing unit is set. |
| Causes: | • Developing unit • Front side board (FRB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Check the connector between the developing unit-FRB CN13 (C2414), CN14 (C2411), CN15 (C2412), CN16 (C2413) for proper connection and correct as necessary. 3. Check the connector between FRB CN1, CN3-MFPB CN4E, CN11E for proper connection and correct as necessary. 4. Replace the developing unit. 5. Replace FRB. 6. Replace MFPB. |
| Error code: | C2413, C2414 |
| Description: | • C2413: Developing unit/Y new article release • C2414: Developing unit/K new article release. The status with the new unit is not cleared after the new developing unit is set |
| Causes: | • Developing unit • Front side board (FRB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Check the connector between the developing unit-FRB CN13 (C2414), CN14 (C2411), CN15 (C2412), CN16 (C2413) for proper connection and correct as necessary. 3. Check the connector between FRB CN1, CN3-MFPB CN4E, CN11E for proper connection and correct as necessary. 4. Replace the developing unit. 5. Replace FRB. 6. Replace MFPB. |
| Error code: | C2551, C2553, C2555 |
| Description: | • C2551: Abnormally low toner density detected cyan TCR sensor • C2553: Abnormally low toner density detected magenta TCR sensor • C2555: Abnormally low toner density detected yellow TCR sensor When sampling data is determined in TC ratio calculation control, TCR sensor output is lower than a predetermined value for a predetermined number of times in a row even though there is toner in the sub hopper. |
| Causes: | • Imaging unit/C • Imaging unit/M • Imaging unit/Y • Toner cartridge/C • Toner cartridge/M • Toner cartridge/Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor/YM (M13) • Toner cartridge motor /CK (M14) • Process drive board (PDB) • MFP board (MFPB) |
| Remedy: | 1. Perform image troubleshooting procedure if image density is low. 2. Reinstall the imaging unit. 3. Reinstall the toner cartridge. 4. Check the connector between M9-relay CN258-PDB CN8 for proper connection and correct as necessary. 5. Check the connector between M10-relay CN258-PDB CN8 for proper connection and correct as necessary. 6. Check the connector between M11-relay CN258-PDB CN8 for proper connection and correct as necessary. 7. Check the connector between M13-relay CN320-relay CN330-PDB CN7 for proper connection and correct as necessary. 8. Check the connector between M14-relay CN321-relay CN428-PDB CN7 for proper connection and correct as necessary. 9. Check the connector of M9, M10, M11, M13, M14 for proper drive coupling and correct as necessary. 10. Check the connector between RS/C-relay CN291-relay CN265-MFPB CN4E for proper connection and correct as necessary. 11. Check the connector between RS/M-relay CN246-relay CN265-MFPB CN4E for proper connection and correct as necessary. 12. Check the connector between RS/Y-relay CN247-relay CN265-MFPB CN4E for proper connection and correct as necessary. 13. RS/C, RS/M, RS/Y I/O check, sensor check • Control signal: MFPB CN4E<B>-6 (RS/C), MFPB CN4E<B>-8 (RS/M), MFPB CN4E<B>-10 (RS/Y) • Location of electrical component: 16 to 17-C 14. M9, M10, M11 operation check (At this time, IU must be non-installation.) • Control signal: PDB CN8-1 to 4 (M9), PDB CN8-5 to 8 (M10), PDB CN8-9 to 12 (M11) • Location of electrical component: 15 to 16-X 15. M13, M14 operation check • Control signal: PDB CN7-9 to 12 (M13), PDB CN7-1 to 4 (M14) • Location of electrical component: 17 to 18-P 16. Replace M9, M10, M11. 17. Replace M13. 18. Replace M14. 19. Replace the corresponding imaging unit. 20. PDB F1 or F2 conduction check 21. Replace PDB. 22. Replace MFPB. |
| Error code: | C2552, C2554 |
| Description: | • C2552: Abnormally high toner density detected cyan TCR sensor • C2554: Abnormally high toner density detected magenta TCR sensor. |
| Causes: | The TC ratio of the toner determined by the toner replenishment control is detected to be the predetermined value or over for consecutive times. |
| Remedy: | • Developing unit/C,M,Y,K • Toner cartridge/C,M,Y,K • Front side board (FRB) • MFP board (MFPB) |
| Error code: | C2556, C2558 |
| Description: | • C2556: Abnormally high toner density detected yellow TCR sensor • C2558: Abnormally high toner density detected black TCR sensor. The TC ratio of the toner determined by the toner replenishment control is detected to be the predetermined value or over for consecutive times. |
| Causes: | • Developing unit/C,M,Y,K • Toner cartridge/C,M,Y,K • Front side board (FRB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Reinstall toner cartridge. 3. Check the connector between the developing unit-FRB CN13 (C2558), CN14 (C2552), CN15 (C2554), CN16 (C2556) for proper connection and correct as necessary. 4. Check the connector between FRB CN1, CN3-MFPB CN4E, CN11E for proper connection and correct as necessary. 5. Replace the developing unit. 6. Replace FRB. 7. Replace MFPB. |
| Error code: | C2557 |
| Description: | Abnormally low toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Developing unit • Toner cartridge • Toner empty sensor/K (PZS/K) • Toner supply motor/K (M12) • Toner cartridge motor/CK (M14) • MFP board (MFPB) |
| Remedy: | 1 M3 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 D-23. 2 Reinstall imaging unit. 3 Reinstall toner cartridge. 4 Change imaging unit /K. 5 Change PRCB. |
| Error code: | C2559, C255A, C255B |
| Description: | • C2559: Cyan TCR sensor adjustment failure • C255A: Magenta TCR sensor adjustment failure • C255B: Yellow TCR sensor adjustment failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/C • Imaging unit/M • Imaging unit/Y • PH relay board (PHRYB) |
| Remedy: | 1. Reinstall the imaging unit. 2. Replace the corresponding imaging unit. 3. Replace PHRYB. |
| Error code: | C255C |
| Description: | Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit /K. 2 Change imaging unit /K. 3 Change PRCB. |
| Error code: | C2561, C2562 |
| Description: | • C2561: Cyan TCR sensor failure • C2562: Magenta TCR sensor failure. Alarm signals for each TCR sensor is detected more than the predetermined number of times. This detection is used for detecting disconnection of TCR sensor connector. |
| Causes: | • Developing unit/C,M,Y,K • Front side board (FRB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Check the connector between the developing unit-FRB CN13 (C2564), CN14 (C2561), CN15 (C2562), CN16 (C2563) for proper connection and correct as necessary. 3. Check the connector between FRB CN1, CN3-MFPB CN4E, CN11E for proper connection and correct as necessary. 4. Replace the developing unit. 5. Replace FRB. 6. MFPB ICP2E conduction check 7. Replace MFPB. |
| Error code: | C2563, C2564 |
| Description: | • C2563: Yellow TCR sensor failure • C2564: Black TCR sensor failure. Alarm signals for each TCR sensor is detected more than the predetermined number of times. This detection is used for detecting disconnection of TCR sensor connector. |
| Causes: | • Developing unit/C,M,Y,K • Front side board (FRB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Check the connector between the developing unit-FRB CN13 (C2564), CN14 (C2561), CN15 (C2562), CN16 (C2563) for proper connection and correct as necessary. 3. Check the connector between FRB CN1, CN3-MFPB CN4E, CN11E for proper connection and correct as necessary. 4. Replace the developing unit. 5. Replace FRB. 6. MFPB ICP2E conduction check 7. Replace MFPB. |
| Error code: | C2650 |
| Description: | PF feed motor error (Side Multi Feeder) Object: Side multi feeder |
| Causes: | The ready signal is not at the L level (stable rotation) for passing 2s since the PF feed motor drive is started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected. The drive parts are faulty. Execute U247 [SMT] > [Motor On] to check the paper feeding operation. If the PF feed motor does not properly operate, reconnect the connector. Check if the PF feed roller and the drive gears rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. Executing U247 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF main PWB • PF main PWB - Engine PWB (Cable from the side multi feeder) Wiring diagram 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF drive unit (Side multi feeder) 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 5 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2A11, C2A12 |
| Description: | • C2A11: Drum unit/C new release failure • C2A12: Drum unit/M new release failure. The status with the new unit is not cleared after the new drum unit is set. |
| Causes: | • Drum unit/C,M,Y,K • Front side board (FRB) • MFP board (MFPB) |
| Remedy: | 1. Clean the connection between the drum unit and the machine if dirty. 2. Reinstall the drum unit. 3. Check the connector between the drum unit-FRB CN12 for proper connection and correct as necessary. 4. Check the connector between FRB CN1, CN3-MFPB CN4E, CN11E for proper connection and correct as necessary. 5. Replace the drum unit. 6. Replace FRB. 7. Replace MFPB. |
| Error code: | C2A21, C2A22 |
| Description: | • C2A21: Toner cartridge/C new release failure • C2A22: Toner cartridge/M new release failure. The status with the new unit is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/ C,M,Y,K • MFP board (MFPB) |
| Remedy: | 1. Clean the connection between the toner cartridge and the machine if dirty. 2. Check the connector between the toner cartridge-relay CN79-MFPB CN35E for proper connection and correct as necessary. 3. Reinstall the toner cartridge. 4. Check the harness for proper connection and correct as necessary. 5. Replace the toner cartridge. 6. Replace MFPB. |
| Error code: | C2A23, C2A24 |
| Description: | • C2A23: Toner cartridge/Y new release failure • C2A24: Toner cartridge/K new release failure. The status with the new unit is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/ C,M,Y,K • MFP board (MFPB) |
| Remedy: | 1. Clean the connection between the toner cartridge and the machine if dirty. 2. Check the connector between the toner cartridge-relay CN79-MFPB CN35E for proper connection and correct as necessary. 3. Reinstall the toner cartridge. 4. Check the harness for proper connection and correct as necessary. 5. Replace the toner cartridge. 6. Replace MFPB. |
| Error code: | C3101, C3103 |
| Description: | • C3101: Pressure roller pressure failure • C3103: Pressure roller release failure C3101: • The fusing pressure home sensor (PS59) is not turned ON (pressed state) after the set period of time after the fusing pressure roller pressure operation is started. • The fusing pressure home sensor (PS59) is not ON (pressed state) when the fusing pressure roller pressure operation is completed. C3103: • The fusing pressure home sensor (PS59) is not turned OFF (retracted state) even after the set period of time after the fusing pressure roller retraction operation is started. • The fusing pressure home sensor (PS59) is not OFF (retracted state) when the fusing pressure roller retraction operation is completed. |
| Causes: | • Fusing unit • Fusing pressure home sensor (PS59) • Fusing pressure motor (M34) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M34-MFPB CN16E for proper connection and correct as necessary. 2. Check the connector of M34 for proper drive coupling and correct as necessary. 3. Check the fusing unit-relay CN260-MFPB CN30E for proper connection and correct or change as necessary. 4. PS59 I/O check, sensor check • Control signal: MFPB CN30E-11 (ON) • Location of electrical component: 9-C, 12-C 5. M34 operation check • Control signal: MFPB CN16E-8 to 11 • Location of electrical component: 10-K 6. Replace M34. 7. Replace the fusing unit. 8. MFPB F2E or F14E conduction check 9. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C3201, C3202 |
| Description: | • C3201: Fusing motor failure to turn • C3202: Fusing motor turning at abnormal timing • C3201: The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. • C3202: The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M30-MFPB CN16E for proper connection and correct as necessary. 2. Check the loading status of the fusing unit drive, and correct the error as necessary. 3. M30 operation check • Control signal: MFPB CN16E-4 (REM), MFPB CN16E-7 (LOCK) • Location of electrical component: 10-K 4. Replace M30. 5. MFPB F14E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C3302 |
| Description: | Fusing cooling fan motor/ 2,3 failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Paper cooling fan (FM8) • Printer control board (PRCB) |
| Remedy: | 1 Check the FM10 or FM11 connector for proper connection and correct as necessary 2 Check the fan for possible overload and correct as necessary. 3 FM10/FM11 operation check PRCB CN40PRCB-5 (ON) PRCB CN40PRCB-6 (LOCK) D-19. PRCB CN40PRCB-8 (ON) PRCB CN40PRCB-9 (LOCK) D-18. 4 Change FM10/FM11. 5 Change PRCB. |
| Error code: | C3425 |
| Description: | Fusing warm-up trouble. bizhub 958, bizhub PRO 958: • After warm-up operation starts, the fusing belt temperature sensor/1 (TEMS1) does not detect a temperature increasing to a predetermined one though a predetermined period of time has elapsed. • From the start of warm-up operation, it does not terminate within a predetermined period of time. b izhub 808/758: • After warm-up operation starts, the heating roller temperature sensor/1 (TEMS1) does not detect a temperature increasing to a predetermined one though a predetermined period of time has elapsed. • From the start of warm-up operation, it does not terminate within a predetermined period of time. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Check the connector between NF1 CN2-IHPU CN1 for proper connection and correct as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Replace the fusing unit. 8. Replace IHPU. 9. MFPB IC80E conduction check 10. Replace MFPB. 11. Replace NF1. |
| Error code: | C3722, C3725, C3726 |
| Description: | • C3722: Fusing abnormally high temperature detection (Edge of the heating roller) • C3725: Fusing abnormally high temperature detection (Middle of the heating roller) • C3726: Fusing abnormally high temperature detection (Center of the heating roller) bizhub 958, bizhub PRO 958: • C3722: Detected temperature of the fusing belt temperature sensor/3 (TEMS3) goes beyond a given temperature for a given period of time consecutively. • C3725: Detected temperature of the fusing belt temperature sensor/1 (TEMS1) goes beyond a given temperature for a given period of time consecutively. • C3726: Detected temperature of the fusing belt temperature sensor/2 (TEMS2) goes beyond a given temperature for a given period of time consecutively. bizhub 808/758: • C3722: Detected temperature of the heating roller temperature sensor/3 (TEMS3) goes beyond a given temperature for a given period of time consecutively. • C3725: Detected temperature of the heating roller temperature sensor/1 (TEMS1) goes beyond a given temperature for a given period of time consecutively. • C3726: Detected temperature of the heating roller temperature sensor/2 (TEMS2) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • C3725: Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • C3725: Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • C3726: Fusing belt temperature sensor/2 (TEMS2) (bizhub 958, bizhub PRO 958) • C3726: Heating roller temperature sensor/2 (TEMS2) (bizhub 808/758) • C3722: Fusing belt temperature sensor/3 (TEMS3) (bizhub 958, bizhub PRO 958) • C3722: Heating roller temperature sensor/3 (TEMS3) (bizhub 808/758) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1, TEMS2, TEMS3-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Check the connector between NF1 CN2-IHPU CN1 for proper connection and correct as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Replace the fusing unit. 8. Replace IHPU. 9. Replace MFPB. 10. Replace NF1 |
| Error code: | C3731 |
| Description: | Fusing abnormally high temperature (Hard protector). An abnormally high temperature of the hard protector signal is detected. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • Fusing belt temperature sensor/2 (TEMS2) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/2 (TEMS2) (bizhub 808/758) • Fusing belt temperature sensor/3 (TEMS3) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/3 (TEMS3) (bizhub 808/758) • Pressure roller thermistor/2 (TH3) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1, TEMS2, TEMS3-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Replace the fusing unit. 6. Replace TEMS1, TEMS2, TEMS3. 7. Replace MFPB. |
| Error code: | C3825, C3826 |
| Description: | • C3825: Fusing abnormally low temperature detection (Main of the heating roller) • C3826: Fusing abnormally low temperature detection (Center of the heating roller). • C3825: The heating roller temperature sensor (TEMS) continues to detect a temperature lower than a predetermined one for a predetermined period of time. • C3826: The heating roller thermistor/2 (TH2) continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | • Fusing unit • C3825: Heating roller temperature sensor (TEMS) • C3826: Heating roller thermistor/2 (TH2) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the right door. 3. Check the fusing unit and MFPB for proper connection and correct or change as necessary. 4. Replace the fusing unit. 5. Replace MFPB. |
| Error code: | C3922, C3925, C3926 |
| Description: | C3922: • Fusing sensor wire breaks detection (Edge of the heating roller) • Fusing unit for incorrect marketing area (The fusing unit for incorrect marketing area is installed) C3925: Fusing sensor wire breaks detection (Middle of the heating roller) C3926: • Fusing sensor wire breaks detection (Center of the heating roller) • Fusing unit for incorrect marketing area (The fusing unit for incorrect marketing area is installed) bizhub 958, bizhub PRO 958: • C3922: After a predetermined period of time after the warm-up stage is started, the fusing belt temperature sensor/3 (TEMS3) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. • C3925: After a predetermined period of time after the warm-up stage is started, the fusing belt temperature sensor/1 (TEMS1) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. • C3926: After a predetermined period of time after the warm-up stage is started, the fusing belt temperature sensor/2 (TEMS2) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. bizhub 808/758: • C3922: After a predetermined period of time after the warm-up stage is started, the heating roller temperature sensor/3 (TEMS3) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. • C3925: After a predetermined period of time after the warm-up stage is started, the heating roller temperature sensor/1 (TEMS1) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. • C3926: After a predetermined period of time after the warm-up stage is started, the heating roller temperature sensor/2 (TEMS2) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • C3925: Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • C3925: Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • C3926: Fusing belt temperature sensor/2 (TEMS2) (bizhub 958, bizhub PRO 958) • C3926: Heating roller temperature sensor/2 (TEMS2) (bizhub 808/758) • C3922: Fusing belt temperature sensor/3 (TEMS3) (bizhub 958, bizhub PRO 958) • C3922: Heating roller temperature sensor/3 (TEMS3) (bizhub 808/758) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1, TEMS2, TEMS3-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Check the connector between NF1 CN2-IHPU CN1 for proper connection and correct as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Replace the fusing unit. 8. Replace IHPU. 9. MFPB IC80E conduction check 10. Replace MFPB. 11. Replace NF1. |
| Error code: | C392A |
| Description: | Fusing belt temperature sensor/1 contamination (Middle of the heating roller) (bizhub 958) Heating roller temperature sensor contamination (Middle of the heating roller (bizhub 808/758)bizhub 958, bizhub PRO 958: During waiting after a predetermined period of time after the warm-up stage terminates, the temperature detected by the fusing belt thermistor/1 (TH1) exceeds that detected by the fusing belt temperature sensor/1 (TEMS1) above a predetermined temperature, and this state continues for a predetermined period of time. bizhub 808/758: During waiting after a predetermined period of time after the warm-up stage terminates, the temperature detected by the heating roller thermostat/1 (TH1) exceeds that detected by the heating roller temperature sensor/1 (TEMS1) above a predetermined temperature, and this state continues for a predetermined period of time. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • Fusing belt thermistor/1 (TH1) (bizhub 958, bizhub PRO 958) • Heating roller thermostat/1 (TH1) (bizhub 808/758) • IH power supply unit (IHPU) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1. Wipe the TEMS1 clean of dirt if any. • Clear away a dirt or a foreign object on the sensor with a cotton swab. • When a dirt is left even if you cleaned the sensor by above procedure, clear away a dirt or a foreign object on the sensor using a cotton swab dampened with the alcohol. And, wipe off the sensor with a dry cotton swab afterwards. 2. Check the TEMS1 for installed position and proper connector connection. 3. Check the TH1 for installed position and proper connector connection. 4. Check the connection of the fusing unit. 5. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Check the connector between DCPU CN009-MFPB CN31E for proper connection and correct as necessary. 8. Replace the fusing unit. 9. Replace MFPB. |
| Error code: | C392B |
| Description: | Fusing disconnection error detection (difference of temperature) bizhub 958, bizhub PRO 958: The difference between the temperature corrected by the fusing belt thermistor/1 (TH1) and the temperature detected by the fusing belt temperature sensor/1 (TEMS1) exceeds a predetermined value after warm up. bizhub 808/758: The difference between the temperature corrected by the heating roller thermistor/1 (TH1) and the temperature detected by the heating roller temperature sensor/1 (TEMS1) exceeds a predetermined value after warm up. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • Fusing belt thermistor/1 (TH1) (bizhub 958, bizhub PRO 958) • Heating roller thermostat/1 (TH1) (bizhub 808/758) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Check the connector between NF1 CN2-IHPU CN1 for proper connection and correct as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Replace the fusing unit. 8. Replace IHPU. 9. Replace MFPB. 10. Replace NF1. |
| Error code: | C4091 |
| Description: | I/F communication error. The communication between the MFPB and PRCB can not be completed even when elapsed a given period of time. |
| Causes: | • MFP board (MFPB) • Printer control board (PRCB) |
| Remedy: | 1 Reboot the machine. 2 Check the flat cable between MFPB PJ03-PRCB CN41 for proper connection and correct as necessary. 3 Check the connected portion of the flat cable for any curled pattern or any scratches, and replace it if necessary. 4 Replace MFPB 5 Replace PRCB |
| Error code: | C40A1, C40A2 |
| Description: | • C40A1: Mechanical controller sub-CPU communication error • C40A2: Mechanical controller PF communication data error. A CPU communication error is detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | C4101 |
| Description: | BD initialization error |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4501 |
| Description: | Laser malfunction. • SOS signal is not detected even after the lapse of a given period of time after starting the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Causes: | • PH unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between the PH unit-PHRYB CN8 for proper connection and correct as necessary. 2. Replace the PH unit. 3. PHRYB IC5 conduction check. 4. Replace PHRYB. 5. Replace MFPB. |
| Error code: | C5102, C5103 |
| Description: | • C5102: Transport motor failure to turn • C5103: Transport motor turning at abnormal timing. • C5102: The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. • C5103: The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Transport motor (M1) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between M1-MFPB CN8E for proper connection and correct as necessary. 2. Check the loading status of the transfer belt drive, and correct the error as necessary. 3. M1 operation check • Control signal: MFPB CN8E-3 (REM), MFPB CN8E-6 (LOCK) • Location of electrical component: 2-C 4. Replace M1. 5. Replace MFPB. |
| Error code: | C5351 |
| Description: | Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • DC power supply cooling fan (FM9) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1 Check the FM5 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check PRCB CN30PRCB-11 (ON) PRCB CN30PRCB-12 (LOCK) K-8. 4 Change FM5. 5 Change DCPU. 6 Change PRCB. |
| Error code: | C5355 |
| Description: | Toner cartridge cooling fan’s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Toner cartridge cooling fan (FM8) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM8-relay CN522-MFPB CN24E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM8 operation check • Control signal: MFPB CN24E-4 (DRIVE), MFPB CN24E-6 (LOCK) • Location of electrical component: 1-K 4. Replace FM8. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE: • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C5360 |
| Description: | Exhaust fan 1 failure to turn (When CU-102 is installed). The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Exhaust fan 1 (FM14) • Clean unit drive board (CUDB) • Process drive board (PDB) |
| Remedy: | 1. Check the connector between FM14-relay CN316-CUDB CN2 for proper connection and correct as necessary. 2. Check the connector between CUDB CN1-relay CN315-PDB CN6 for proper connection and correct as necessary. 3. Check the fan for possible overload and correct as necessary. 4. FM14 load check • Check code: 42 • Multi code: 27 • Control signal: CUDB CN2-1 (REM), CUDB CN2-3 (LOCK) • Location of electrical component: 16-Y 5. Replace FM14. 6. Replace CUDB. 7. PDB PS1 conduction check 8. Replace PDB. |
| Error code: | C5370 |
| Description: | Rear side cooling fan’s failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan remains stationary. |
| Causes: | • MFP control board cooling fan (FM17) • MFP board (MFPB) |
| Remedy: | 1 Check the connector between FM3-MFPB PJ26 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM3 operation check MFPB PJ26 (LOCK) 7-P. 4 Replace FM3. 5 Replace MFPB. |
| Error code: | C5501 |
| Description: | AC signal abnormality The zero cross signal is not input during fusing phase control. |
| Causes: | • Fusing unit • DC power supply (DCPU) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU and PRCB for proper connection and correct or change as necessary. 3 Replace fusing unit. 4 Replace PRCB. 5 Replace DCPU. |
| Error code: | C5601 |
| Description: | Engine control malfunction. Engine control malfunction is detected with port monitor control. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | C5603 |
| Description: | Expansion control board communication error Communication error is detected in expansion control board. |
| Causes: | • Expansion control board (EXCB) • Front side board (FRB) • PH unit • Printer control board (PRCB) |
| Remedy: | 1 Reboot the machine. 2 Check the connector between EXCB-PRCB for proper connection and correct as necessary. 3 PRCB ICP12 conduction check. 4 Replace EXCB. 5 Replace PRCB. |
| Error code: | C5604 |
| Description: | PH configuration fault. A disagreement in PH unit configuration is detected. |
| Causes: | • PH unit • MFP board (MFPB) |
| Remedy: | 1. Check the type of the installed PH unit and replace it if it is a wrong one. 2. Check the connector between the PH unit-MFPB for proper connection and correct as necessary. 3. Replace MFPB. |
| Error code: | C5605, C5606 |
| Description: | • C5605: Engine communication data error • C5606: Engine transmission timeout. A communication error is detected between CPUs. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | C5610 |
| Description: | Drum surface potential problem 2 • The sensor output is 0.5 V or less. • Potential adjustment in 30 times could not lower the potential sensor value to the predetermined. |
| Causes: | Defective drum surface potential sensor. Defective high voltage PWB. Defective drum. Defective engine PWB. |
| Remedy: | Defective drum surface potential sensor. Replace the drum surface potential sensor. Defective high voltage PWB. Replace the high voltage PWB and check for correct operation. Defective drum. Replace the drum. Defective engine PWB. Replace the engine PWB. |
| Error code: | C5611 |
| Description: | PH EEPROM communication error. Results of two readings of the EEPROM data disagree with each other. |
| Causes: | • Front side board (FRB) • PH unit • MFP board (MFPB) |
| Remedy: | 1. Reboot the machine. 2. Check the connector between FRB CN5-PH unit for proper connection and correct as necessary. 3. Check the connector between FRB CN2-MFPB CN10E for proper connection and correct as necessary. 4. Replace FRB. 5. Replace the PH unit. 6. Replace MFPB. |
| Error code: | C6001 |
| Description: | DF related configuration error 1. Inconsistency in the configuration with the installed DF is detected on the main body. |
| Causes: | • DF control board (DFCB) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1. Check the type of the installed DF and replace it if it is a wrong one. 2. Correct the harness connection between DFCB CN12-relay CN47-MFPB CN1E if faulty. 3. Correct the harness connection between DSIPB CN1-MFPB CN24 if faulty. 4. Replace DFCB. 5. Replace DSIPB. 6. Replace MFPB. |
| Error code: | C6002 |
| Description: | DF related configuration error 2. Inconsistency in the configuration with the installed DF is detected on the DF. |
| Causes: | • DF control board (DFCB) • Dual scan image processing board (DSIPB) |
| Remedy: | 1. Check the type of the installed DF and replace it if it is a wrong one. 2. Correct the harness connection between DFCB CN12-relay CN47-MFPB CN1E if faulty. 3. Correct the harness connection between DSIPB CN1-MFPB CN24 if faulty. 4. Check the connectors of the dual scan image processing board (DSIPB) for proper connection, and correct as necessary. (Direction of the point of contact and connection state of the flat cable in particular) |
| Error code: | C6102, C6103 |
| Description: | • C6102: Drive system home sensor malfunction • C6103: Slider over running C6102: • The scanner home sensor is unable to detect the scanner located at its home position. • The scanner home sensor is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor. C6103: The scanner home sensor detects the scanner at its home position during a period of time that begins with the time when a prescan command and a scan preparation command are executed and ends when a home return command is executed. |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2. Correct the scanner motor set screw if loose. 3. Adjust [Image Position: Leading Edge] and [Sub Scan Zoom Adj.]. 4. Check the connector between PS201-SCDB CN6 for proper connection and correct as necessary. 5. Check the connector between M201-SCDB CN4 for proper connection and correct as necessary. 6. Check the connector between SCDB CN2-MFPB CN1E for proper connection and correct as necessary. 7. PS201 I/O check, sensor check • Control signal: SCDB CN6-3 (ON) • Location of electrical component: 17-U 8. M201 operation check • Control signal: SCDB CN4-1 to 4 • Location of electrical component: 17-U 9. Replace SCDB 10. MFPB F3E conduction check 11. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C6104, C6105 |
| Description: | • C6104: Back side cleaning home sensor abnormality (initial) • C6105: Back side cleaning home sensor abnormality (normal) C6104: • The back side cleaning home sensor (PS9) does not change from H to L even after the lapse of a given period of time after the home position detecting operation is started at the initial operation. • The back side cleaning home sensor (PS9) does not change from H to L even after the lapse of a given period of time after the home position detecting operation is started at the initial operation. C6105: At the time of operation other than the initial operation, the back side cleaning home sensor (PS9) error is detected. |
| Causes: | • Back side cleaning home sensor (PS9) • Back side cleaning motor (M7) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M7-DFCB CN14 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-relay CN121-DFCB CN18 for proper connection and correct as necessary. 4. PS9 I/O check, sensor check • Control signal: DFCB CN18-6 (ON) • Location of electrical component: DF 3 to 4-C 5. M7 operation check • Control signal: DFCB CN14-6 to 9 • Location of electrical component: DF 6-C 6. Replace M7. 7. DFCB ICP4 or ICP8 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C6704 |
| Description: | Image input time out. Image data is not input from the scanner to the MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Memory Bus Check] -> [Scanner -> Memory], and conduct the memory bus function. 2. Correct the harness connection between scanner section and MFPB if faulty. 3. MFPB F3E conduction check 4. Replace MFPB. 5. Replace the CCD unit. |
| Error code: | C6751 |
| Description: | CCD gain adjustment failure. • The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment. |
| Causes: | • LED exposure unit • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 2. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 3. Correct the harness connection between SCDB CN1-DCPU CN005 if faulty. 4. Check for possible extraneous light and correct as necessary. 5. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 6. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 7. Replace SCDB 8. Replace the CCD unit. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | C6752 |
| Description: | ASIC clock input error (front side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on CCD board (CCDB) was conducted, and verification failure was detected. |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Correct the harness connection of CCDB if faulty. 2. Replace the CCD unit. 3. MFPB F3E conduction check 4. Replace MFPB. |
| Error code: | C6753 |
| Description: | ASIC clock input error (back side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on dual scan image processing board (DSIPB) was conducted, and verification failure was detected. |
| Causes: | • CIS module (CIS) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CIS J101-DSIPB CN2 if faulty. 2. Correct the harness connection between DSIPB CN1-MFPB CN24 if faulty. 3. Replace CIS. 4. DFPU ICP1 conduction check. 5. Replace DSIPB. 6. MFPB F3E conduction check 7. Replace MFPB. |
| Error code: | C6754, C6755 |
| Description: | • C6754: CIS clamp adjustment failure • C6755: CIS gain adjustment failure • C6754: After the gain adjustment is performed at the start-up, the CIS clamp adjustment value is too high or too low. • C6755: After the gain adjustment is performed at the start-up, the peak value of the output data is lower than a given value. |
| Causes: | • CIS module (CIS) • Dual scan image processing board (DSIPB) • DF power supply (DFPU) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CIS J101-DSIPB CN2 if faulty. 2. Correct the harness connection between CIS J102-DFPU CN2 if faulty. 3. Check for possible extraneous light and correct as necessary. 4. Clean the back side reading glass and the shading sheet if dirty. 5. Replace CIS. 6. Replace DSIPB. 7. DFPU ICP1 conduction check. 8. Replace DFPU. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | C6756 |
| Description: | CCD power-supply voltage malfunction. Power is not supplied to CCD after the lapse of a given period of time after the main power switch is turned ON or the machine recovers from the sleep mode. |
| Causes: | • CCD board (CCDB) • Scanner drive board (SCDB) • DC power supply unit (DCPU) |
| Remedy: | 1. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 2. Correct the harness connection between SCDB CN1 and DCPU CN005 if faulty. 3. Replace the CCD unit. 4. Replace SCDB. 5. Replace DCPU. |
| Error code: | C6901, C6902, C6903 |
| Description: | • C6901: DSC board mount failure 1 • C6902: DSC Bus check NG1-1 • C6903: DSC Bus check NG1-2 • C6901: When MFP detects that DSC board/1 (front side) is not properly installed. • C6902, C6903: When DSC bus check (front side) detects an error. |
| Causes: | • DSC board/1 (DSCB/1: SC-508) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection of DSCB/1 if faulty. 2. Replace DSCB/1. 3. Replace MFPB. |
| Error code: | C6911, C6912, C6913 |
| Description: | • C6911: DSC board mount failure 2 • C6912: DSC Bus check NG2-1 • C6913: DSC Bus check NG2-2 • C6911: When MFP detects that DSC board/2 (back side) is not properly installed. • C6912, C6913: When DSC bus check (back side) detects an error. |
| Causes: | • DSC board/2 (DSCB/2; SC-508) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection of DSCB/2 if faulty. 2. Correct the harness connection of DSIPB if faulty. 3. Replace DSCB/2. 4. Replace DSIPB. 5. Replace MFPB. |
| Error code: | C6F01 ... C6FDD |
| Description: | • C6F01: Scanner sequence trouble 1 • C6F02: Scanner sequence trouble 2 • C6F03: Scanner sequence trouble 3 • C6F04: Scanner sequence trouble 4 • C6F05: Scanner sequence trouble 5 • C6F06: Scanner sequence trouble 6 • C6F07: Scanner sequence trouble 7 • C6F08: Scanner sequence trouble 8 • C6F09: Scanner sequence trouble 9 • C6F0A: Scanner sequence trouble 10 • C6FDC: Scanner sequence trouble DC • C6FDD Scanner sequence trouble DD. The original transport interval becomes shorter than the predetermined value due to an original transport control error in original reading in DF. |
| Causes: | • MFP board (MFPB) • DF control board (DFCB) |
| Remedy: | 1. Correct the harness connection between main body and DF if faulty. 2. Replace DFCB (DF-629/DF-704) 3. Replace MFPB. |
| Error code: | C8101 |
| Description: | Before reading pressure welding alienation mechanism trouble. • During a pressure motion being performed, the before read sensor (PS6) output does not change from H to L. • During a retraction motion being performed, the before read sensor (PS6) output does not change from L to H. |
| Causes: | • Reading roller pressure/retraction motor (M6) • Before read sensor (PS6) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M6-relay CN118-DFCB CN4 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-relay CN120-DFCB CN11 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: DFCB CN11-2 (ON) • Location of electrical component: DF 1-C 5. M6 operation check • Control signal: DFCB CN4-1 to 2 • Location of electrical component: DF 10-C 6. Replace M6. 7. DFCB ICP9 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8107 |
| Description: | Glass cleaning mechanism trouble. The front side cleaning home sensor (PS18) is not turned ON (unblocked) even after the set period of time has elapsed after the front side cleaning motor (M8) turned ON. |
| Causes: | • Front side cleaning motor (M8) • Front side cleaning home sensor (PS18) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M8-DFCB CN14 for proper connection and correct as necessary. 2. Check the connector between PS18-DFCB CN18 for proper connection and correct as necessary. 3. Check the connector of M8 for proper drive coupling and correct as necessary. 4. PS18 I/O check, sensor check • Control signal: DFCB CN18-3 (ON) • Location of electrical component: DF 3-C 5. M8 operation check • Control signal: DFCB CN14-1 to 4 • Location of electrical component: DF 6-C 6. Replace M8. 7. DFCB ICP8 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8302 |
| Description: | Cooling fan motor`s failure. The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Cooling fan motor (FM) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between FM-relay CN115-DFCB CN19 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM operation check • Control signal: DFCB CN19-3 (LOCK) • Location of electrical component: DF 4-C 4. Replace FM. 5. DFCB ICP10 conduction check. 6. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8401 |
| Description: | Nonvolatile memory error. The EEPROM writing is disabled. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Check the DFCB connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Replace DFCB. |
| Error code: | C9401, C9402 |
| Description: | • C9401: Exposure LED lighting failure/ROM contents error (MSC) • C9402: Exposure LED lighting abnormally C9401: • The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment. • The wrong model of firmware is detected in the MFP board when the main power switch is turned ON. • The machine type information (Machine, Type) registered to the machine differs from the actual machine type. C9402: The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job. |
| Causes: | • LED exposure unit • Flat cable (LED exposure unit) • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1. Check the machine type information registered and reenter as necessary. For details the machine information, see “ J.3.2 Procedure”. 2. Correct the harness connection between SCDB CN3-LU201 if faulty. 3. Correct the harness connection between SCDB CN2-MFPB CN1E if faulty. 4. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 5. Replace the LED exposure unit. 6. Replace the CCD unit. 7. Replace SCDB 8. MFPB F3E conduction check 9. Replace MFPB. |
| Error code: | C9403, C9404 |
| Description: | • C9403: CIS LED lighting failure • C9404: CIS LED lighting abnormally • C9403: At the CIS gain adjustment, the machine detected that the output of the CIS LED is lower than the specified value. • C9404: After a scan job is completed, the machine detected that the average output of the CIS LED is greater than the specified value. |
| Causes: | • CIS module (CIS) • DF power supply (DFPU) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CIS J101-DSIPB CN2 if faulty. 2. Correct the harness connection between CIS J102-DFPU CN2 if faulty. 3. Replace CIS. 4. DFPU ICP1 conduction check. 5. Replace DFPU. 6. Replace DSIPB. 7. MFPB F3E conduction check 8. Replace MFPB. |
| Error code: | CA051, CA052, CA053 |
| Description: | • CA051: Standard controller configuration failure • CA052: Controller hardware error • CA053: Controller start failure • CA051: The controller of the MFP board (MFPB) is faulty. • CA052: A controller hardware error is detected in the network interface. • CA053: A controller start failure is detected in the controller interface. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check to see if [Service Mode] -> [System 2] -> [Image Controller Setting] has been set to “Controller 0.” If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. 2. Check the connectors of the MFPB for proper connection and correct as necessary. 3. Replace MFPB. |
| Error code: | CC140 |
| Description: | Trouble related to security. |
| Causes: | Trouble related to security. |
| Remedy: | Contact the responsible people of KM before taking some countermeasures. |
| Error code: | CC151, CC152 |
| Description: | • CC151: ROM contents error upon startup (MSC) • CC152: ROM contents error upon startup (IR) • CC151: A fault is detected in a sequence of ROM contents check of the MSC during starting. • CC152: A fault is detected in a sequence of ROM contents check of the IR during starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the ROM version. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CC155 |
| Description: | Finisher ROM error |
| Causes: | FS control board (FSCB) |
| Error code: | CC156 |
| Description: | DF ROM error. Data of flash ROM of the DF is determined to be faulty when the main power switch is turned ON. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace DFCB. |
| Error code: | CC159, CC15A |
| Description: | • CC159: ROM contents error upon startup (DSC1) • CC15A: ROM contents error upon startup (DSC2). A fault is detected in a sequence of ROM contents check of the DSC board during starting. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • DSC board/2 (DSCB/2; SC-508) |
| Remedy: | 1. Check DSCB/1 or DSCB/2 connector for proper connection and correct as necessary. 2. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 3. Rewrite the firmware. 4. Replace DSCB/1 or DSCB/2. |
| Error code: | CC15B |
| Description: | Flash ROM error (saddle). <When FS-536SD or FS-537SD is installed> Data of flash ROM of the saddle is determined to be faulty when the main power switch is turned ON. |
| Causes: | SD control board (SDCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace SDCB. (FS-536SD/FS-537SD) |
| Error code: | CC15C |
| Description: | Engine Flash ROM writing error. Data of flash ROM of the engine is determined to be faulty. |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace PRCB |
| Error code: | CC163 |
| Description: | ROM contents error (PRT) • The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Rewrite the firmware. 2 Change PRCB 2.1. Turn OFF the power switch and replace the current PRCB with a new one. (When using a PRCB of another machine in service, be sure to use a PRCB installed in the same model.) 2.2. Update the PRCB firmware. 2.3. After completing the firmware update, turn OFF and ON the power switch and check to see that warm-up is started. 2.4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SV ERB. 3 Change SV ERB 3.1. Replace the current SV ERB with a new one. 3.2. Turn ON the power switch and check to see that warm-up is started. (One minute is spent to prepare the new SV ERB for use. During the period, the control panel backlight stays off.) 3.3. Make the specified readjustments. 4 If the above actions do not solve the problem, contact KMBT. |
| Error code: | CC164 |
| Description: | ROM contents error (MSC) • The wrong model of firmware is detected in the MFP board when the power switch is turned ON. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the corresponding board. 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CC170 ... CC174 |
| Description: | • CC170: Dynamic link error during starting (AP0) • CC171: Dynamic link error during starting (AP1) • CC172: Dynamic link error during starting (AP2) • CC173: Dynamic link error during starting (AP3) • CC174: Dynamic link error during starting (AP4). A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. If the malfunction code “C-C172” has occurred, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if “Others” is set for the image controller. If any of these is set, according to the kind of controller, select “Controller 0” or “Controller 1.” 2. If the malfunction code "C-C180" has occurred, check to install the appropriate loadable device driver for an authentication unit which is installed to the MFP. When the appropriate loadable device driver is not installed, reinstall the appropriate loadable device driver. 3. Replace MFPB. 4. If the above actions do not solve the problem, contact KM. |
| Error code: | CC180 ... CC186 |
| Description: | • CC180: Dynamic link error during starting (LDR) • CC181: Dynamic link error during starting (IBR) • CC182: Dynamic link error during starting (IID) • CC183: Dynamic link error during starting (IPF) • CC184: Dynamic link error during starting (IMY) • CC185: Dynamic link error during starting (SPF) • CC186: Dynamic link error during starting (OAP). A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. If the malfunction code “C-C172” has occurred, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if “Others” is set for the image controller. If any of these is set, according to the kind of controller, select “Controller 0” or “Controller 1.” 2. If the malfunction code "C-C180" has occurred, check to install the appropriate loadable device driver for an authentication unit which is installed to the MFP. When the appropriate loadable device driver is not installed, reinstall the appropriate loadable device driver. 3. Replace MFPB. 4. If the above actions do not solve the problem, contact KM. |
| Error code: | CC190 |
| Description: | Outline font load error. An error occurred while loading the outline font. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Format the hard disk. 4. Replace the hard disk. (HDD (A) / HDD (B)) 5. Replace MFPB. |
| Error code: | CC191 |
| Description: | Setting parameter load error (LDR). Upon startup, the processing of the loadable device driver setting data file failed. • RAM disk file creation failed. • Reading from the flash ROM failed. • An error occurred in API of the authentication module. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON. 2. Reinstall the loadable device driver. 3. Rewrite the firmware. 4. Replace MFPB. |
| Error code: | CC211 |
| Description: | Authentication device general error. When using the authentication device, authentication data is not to meet the specifications. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. |
| Error code: | CC212 |
| Description: | User validation error. • An error occurred while validating the user authentication information. • The loadable device driver is not successfully installed. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. When this trouble code is generated after installing the loadable device driver, check to see if there is any file other than loadable device driver in USB memory used. If there is any file, reinstall the loadable device driver. 2. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 3. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 4. Re-register the user authentication information. 5. Replace authentication device. |
| Error code: | CC213 |
| Description: | User registration error/Card information setting error. • IC card advanced settings data is not correct when starting-up the authentication device. • Authentication information data is not correct when starting-up the authentication device. • IC card advanced settings data is not correct when setting the IC card advanced settings. • Authentication information data is not correct when setting the IC card advanced settings. • IC card advanced settings data is not correct when registering the authentication information. • Authentication information data is not correct when registering the authentication information. • IC card advanced settings data is not correct when editing the authentication information. • Authentication information data is not correct when editing the authentication information. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 3. Reset the authentication settings. (card type, IC card advanced settings, and etc.) 4. Re-register the user authentication information. |
| Error code: | CC214 |
| Description: | User information deletion error. The deletion of the user information is uncompleted. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. |
| Error code: | CC216 |
| Description: | Acquisition failure of the number of trials/Initialize error of number of authentication. An error occurred during user authentication using optional authentication unit AU-102. |
| Causes: | • MFP board (MFPB) • Authentication device |
| Remedy: | 1. Check the USB cable for proper connection. Reconnect the USB cable as necessary. 2. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 3. Reset the number of authentication trials. |
| Error code: | CD002 |
| Description: | JOB RAM save error • The error in save of JOB data to the memory/ hard disk and its read error are detected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB. |
| Error code: | CD004, CD00F, CD020 |
| Description: | • CD004: Hard disk access error (connection failure) • CD00F: Hard disk data transfer error • CD020: Hard disk verify error • CD004: Unable to communicate between the hard disk and MFP board (MFPB). • CD00F: Data transfer from the hard disk is faulty. • CD020: The data abnormality is detected by the hard disk verify check. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Reinstall the hard disk. 4. Replace the hard disk. (HDD (A) / HDD (B)) 5. Replace MFPB. |
| Error code: | CD010 |
| Description: | Hard disk unformat. Unformatted hard disk is connected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Carry out the [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format]. 2. Replace the hard disk. (HDD (A) / HDD (B)) 3. Replace MFPB. |
| Error code: | CD011 |
| Description: | Hard disk out of specifications mounted. A hard disk that falls outside the specifications is connected. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD012 |
| Description: | Mount error due to hard disk being unformatted. • The hard disk is not logically formatted after the whole data in the hard disk has been deleted by overwriting. • The hard disk that has replaced an old one is not logically formatted. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Logically format the hard disk and then upgrade the firmware. 2. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD013, CD014 |
| Description: | CD013: HDD mirroring error master CD014: HDD mirroring error slave. CD013: A R/W error occurs in the master drive during mirroring. CD014: A R/W error occurs in the slave drive during mirroring. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON. 2. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Status] and identify the specific hard disk that has developed the error. If an error occurs, "Error" appears in the status column. 3. Replace the hard disk that has developed the error with a new one. (HDD (A) / HDD (B)) 4. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [HDD Mirroring Rebuild] and perform the function. |
| Error code: | CD015 |
| Description: | HDD mirroring error master slave. A R/W error occurs in both drives during mirroring. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON. 2. Replace both hard disk (A) and hard disk (B) with new ones. (HDD (A) / HDD (B)) 3. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format] and perform physical format. 4. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format] and perform logical format. 5. If HDD Data Backup has previously been performed, select [Service Mode] -> [Enhanced Security] -> [HDD Data Backup] -> [Restore] and perform the function. 6. If HDD Data Backup has not been performed previously, install voice data, etc. |
| Error code: | CD016 |
| Description: | HDD mirroring error master (rebuild). A R/W error occurs in the master drive during HDD Mirroring Rebuild. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON. If no problems are encountered, HDD Mirroring Rebuild is automatically performed. 2. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Status] and identify the specific hard disk that has developed the error. If an error occurs, "Error" appears in the status column. 3. Replace the hard disk that has developed the error with a new one. (HDD (A) / HDD (B)) 4. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format] and perform physical format. 5. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format] and perform logical format. 6. If HDD Data Backup has previously been performed, select [Service Mode] -> [Enhanced Security] -> [HDD Data Backup] -> [Restore] and perform the function. 7. If HDD Data Backup has not been performed previously, install voice data, etc. |
| Error code: | CD017 |
| Description: | HDD mirroring error slave (rebuild). A R/W error occurs in the slave drive during HDD Mirroring Rebuild. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON. If no problems are encountered, HDD Mirroring Rebuild is automatically performed. 2. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Status] and identify the specific hard disk that has developed the error. If an error occurs, "Error" appears in the status column. 3. Replace the hard disk that has developed the error with a new one. (HDD (A) / HDD (B)) 4. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [HDD Mirroring Rebuild] and perform the function. |
| Error code: | CD030 |
| Description: | Hard disk management information reading error. The machine fails to read administrative information data saved in the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Logically format the hard disk. 4. Physically format the hard disk. 5. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD041 ... CD046 |
| Description: | HDD command execution error. The error occurred inside the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD047 ... CD04B |
| Description: | HDD SCSI library error. The error occurred inside the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD050 |
| Description: | Hard disk recovery timeout. The hard disk fails to recover from the power save mode within the predetermined period of time. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Reinstall the hard disk. 4. Format the hard disk. 5. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD110 |
| Description: | Wireless LAN destination initialization error. When an initialization error occurred on the settings of the wireless LAN in the upgrade kit (UK-212/UK-215). |
| Remedy: | 1. Check the UK-212 or UK-215 connector for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Reinstall the UK-212or UK-215. |
| Error code: | CD201, CD202, CD203 |
| Description: | • CD201: File memory mounting error • CD202: Memory capacity discrepancy • CD203: Memory capacity discrepancy 2 CD201: • The file memory is not mounted. • The file has any abnormality. CD202: • File memory capacity on the MFP board (MFPB) is not enough. • File memory capacity necessary for duplex printing is not enough. CD203: File memory capacity on the MFP board (MFPB) is not enough. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Replace MFPB. |
| Error code: | CD211, CD212 |
| Description: | • CD211: PCI-SDRAM DMA operation failure • CD212: Compression/extraction timeout detection • CD211: Hardware related to the transfer of memory image of the MFP board (MFPB) fails to respond. • CD212: Hardware related to the BTC compression function of the MFP board (MFPB) fails to respond. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Replace MFPB. |
| Error code: | CD241, CD242 |
| Description: | • CD241: Encryption ASIC setting error • CD242: Encryption ASIC mounting error • CD241: Initialization error of the encrypted ASIC is detected during the machine is starting. • CD242: The faulty of the installation of encrypted ASIC is detected during the machine is starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the MFP board connector for proper connection and correct as necessary. 2. Replace MFPB |
| Error code: | CD252 |
| Description: | No relay circuit boards for IC-414 mounting at IC-414 mount setting. EFI relay board (EFIRYB; VI-506) are not mounted when the IC-414 is set to mount setting at Service Mode. |
| Causes: | • MFP board (MFPB) • EFI relay board (EFIRYB; VI-506) |
| Remedy: | 1 If the IC-414 is not mounted, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if "Controller 0" is set for [Image Controller Setting]. - - 2 Check the EFI relay board (EFIRYB; VI-506) connector for proper connection and correct as necessary. - - 3 Replace the EFI relay board (EFIRYB; VI-506) - - 4 Replace MFPB |
| Error code: | CD261 |
| Description: | USB hub board failure. • When a failure is detected in USB hub board included in the local interface kit. • Non-standard USB device is connected. |
| Causes: | • MFP board (MFPB) • USB hub board (USBHB: EK-610/EK-611) |
| Remedy: | 1. Check the operation with another USB device. 2. Check the USB hub board connector for proper connection and correct as necessary. 3. Replace the USB hub board. 4. Replace MFPB. |
| Error code: | CD262 |
| Description: | Extension network adapter installation error. • When the 2nd network card settings is set to “Set” but the upgrade kit (UK-212/UK-215) is not installed. • Upgrade Kit (UK-212/UK-215) is faulty. |
| Remedy: | 1. Check the settings of [Service Mode] -> [Network Settings] -> [2nd Network Setting] -> [2nd network card settings]. 2. Check the UK-212 or UK-215 connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Reinstall the UK-212 or UK-215. |
| Error code: | CD271 |
| Description: | The memory cannot be recognized with the i-Option activated. While the i-Option is activated, the memory on an MFPB cannot be recognized. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CD272 |
| Description: | i-Option activated and HDD not installed. While the i-Option is activated, the hard disk is not installed. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) |
| Remedy: | 1. Access [Service Mode] -> [System 2] -> [HDD] and check to see if “Installed” is selected. 2. Replace the hard disk (A). 3. Replace MFPB. |
| Error code: | CD390 |
| Description: | Nonvolatile data checksum error. Checksum error is detected while nonvolatile data is being checked for error by each data. (The MFP board is replaced with a new one.) |
| Remedy: | 1 Touch [Yes] on the restore screen displayed on the control panel to restore data. - - NOTE • Do not replace the printer control board and SSD board at the same time with new ones or ones removed from other machines. The backup data will be lost and image failure may be caused. |
| Error code: | CD391 |
| Description: | Nonvolatile data save error (eMMC) |
| Remedy: | NOTE • Contact the responsible people of KM before taking some countermeasures. |
| Error code: | CD392 |
| Description: | Nonvolatile data save error (EEPROM). The EEPROM is replaced with a new one. |
| Causes: | • EEPROM/1 • EEPROM/2 |
| Remedy: | 1. Replace the following components with new ones. When the transfer belt unit and the fusing unit have been replaced with new ones, perform [New Release] in the service mode. When the transfer roller has been replaced with a new one, perform [Counter clear]. • Developing unit/Y,M,C,K • Drum unit/Y,M,C,K • Toner cartridge/Y,M,C,K • Transfer belt unit • Fusing unit • Transfer roller • Feed roller, pick-up roller, separation roller (including options) 2. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 3. Set the various setting values in the service mode again. |
| Error code: | CD3A0 |
| Description: | Counter error. The total counter values provided by the MFP board and the eMMC board are different. |
| Causes: | • MFP board (MFPB) • eMMC board (eMMC) |
| Remedy: | 1. If this error occurs temporarily due to the use of the board removed from another machine, reinstall the original board. 2. Replace the current MFPB with a new one. |
| Error code: | CD401 ... CD407 |
| Description: | CD401: NACK command incorrect CD402: ACK command incorrect CD403: Checksum error CD404: Receiving packet incorrect CD405: Receiving packet analysis error CD406: ACK receiving timeout CD407: Retransmission timeout |
| Causes: | MFP board (PRCB) |
| Remedy: | 1 Check whether there is an strong electromagnetic noise source near the main body. 2 Check the connectors on MFPB for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CD411, CD412, CD413 |
| Description: | • CD407: Retransmission timeout • CD411: Touch panel board error • CD412: Touch panel type mismatch • CD413: Electrostatic touch panel operation mode error. When abnormality is found in the communication of controller. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check whether there is a strong electromagnetic noise source near the main body. 2. Check the connectors on MFPB for proper connection and correct as necessary. 3. Replace MFPB |
| Error code: | CD601, CD602, CD603 |
| Description: | Trouble related to security. |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. If the above actions do not solve the problem, contact KM. |
| Error code: | CD701, CD702, CD703 |
| Description: | • CD701: Mechanical controller flash ROM writing error • CD702: Mechanical controller flash ROM device error • CD703: FW download communication fault CD701: A mechanical controller flash ROM writing sequence is interrupted in its mid-operation due to, for example, power being shut off. CD702: An erase error or other device fault occurs during mechanical controller flash ROM writing. CD703: • Irregular data is received during FW downloading. • Places are changed in the order of write completion pulses. • A write completion pulse is received for a memory for which binary writing is not permitted. • Final checksum mismatch in FW download • Two-minute timeout (no response from CTL, the number of transfer data items less than the specified) |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CD704 |
| Description: | Finisher Flash ROM device error (When FS-536, FS-536SD, FS-537, or FS-537SD is installed) An erase error or other device fault occurs during the finisher flash ROM writing. |
| Causes: | FS control board (FSCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace FSCB. (FS-536/FS-536SD/FS-537/FS-537SD) |
| Error code: | CD705, CD706 |
| Description: | • CD705: Mechanical controller sub-CPU flash ROM device error • CD706: Mechanical controller sub-CPU flash ROM error • CD705: An erase error or other device fault occurs during mechanical controller sub-CPU flash ROM writing. • CD706: A data error is determined to exist in the mechanical controller sub-CPU flash ROM during starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | CDF50, CDF70, CDFA0 |
| Description: | • CDF50: ASIC image version failure • CDF70: ASIC image access failure • CDFA0: ASIC image error Communication error is detected between the MFP board (MFPB) and the CCD board (CCDB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Check the connector between MFPB CN9-CCDB PJ3 for proper connection and correct as necessary. 2. Update the firmware. 3. Replace the CCD unit. 4. Replace MFPB. |
| Error code: | CDF51, CDF71, CDFA1 |
| Description: | • CDF51: ASIC image version failure (back side) • CDF71: ASIC image access failure (back side) • CDFA1: ASIC image error (back side) Communication error is detected between the MFP board (MFPB) and the dual scan image processing board (DSIPB). |
| Causes: | • MFP board (MFPB) • Dual scan image processing board (DSIPB) |
| Remedy: | 1. Check the connector between MFPB CN24-DSIPB CN1 for proper connection and correct as necessary. 2. Update the firmware. 3. Replace DSIPB. 4. Replace MFPB. |
| Error code: | CE001 ... CE007 |
| Description: | Abnormal message queue Task error Event error Memory access error Header access error DIMM initialize error |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the connectors on MFPB for proper connection and correct as necessary. 2 Replace MFPB |
| Error code: | CE002 |
| Description: | Message and method parameter failure. MFP board (MFPB) is faulty. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF the main power switch and turn it ON again, and conduct the following setting. [Service Mode] -> [System 1] -> [Initialization] - > [Clear All Data]. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) 4. Replace MFPB. |
| Error code: | CE101 |
| Description: | Browser finish detected. • The browser is automatically recovered (restarted) after the main body detected that the browser (separate process) has stopped with fault. • When the “Malfunction finish is detected over predetermined number of times” or “the browser task process is except in idle (printing, etc)”. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CE201 |
| Description: | Transmission operation log storage fault. When the transmission log storage failed, it repeats retrial until transmission operation log is stored. The trouble is detected when the retrial failed for predetermined number of times. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CE301 ... CE305 |
| Description: | • CE301: Referring incorrect memory • CE302: Incorrect command • CE303: Finished due to error inside Qt library • CE304: Finished due to error outside Qt library • CE305: Program forced to stop Error occurred with the process inside the MFP controller. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. 3. Acquire the debug logs in [Service Mode] -> [Debug Settings] and analyze them. |
| Error code: | CED01 |
| Description: | The authentication application information does not exist in the hard disk/eMMC board in the enhanced server authentication state. With “Enhanced Server Authentication” set, no authentication application registration information is found in the hard disk or the eMMC board (eMMC). |
| Causes: | • eMMC board (eMMC) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF and ON the main power switch. 2. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 3. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 4. Check the connector from eMMC to MFPB for proper connection and correct as necessary. 5. Logically format the hard disk. 6. Replace the hard disk. (HDD (A) / HDD (B)) 7. If the above actions do not solve the problem, contact KM. |
| Error code: | CEEE1, CEEE3 |
| Description: | • CEEE1: MFP board (MSC) malfunction • CEEE3: MFP board (ENG) malfunction MFP board (MFPB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CEEE2 |
| Description: | Scanner section malfunction. A scanner part is faulty. |
| Causes: | • LED exposure unit • CCD board (CCDB) • Scanner drive board (SCDB) |
| Remedy: | 1. Check the connectors on CCDB or MFPB for proper connection and correct as necessary. 2. Replace SCDB 3. Replace the CCD unit. |
| Error code: | D-1 |
| Description: | Split line detect (front side). • While recovering from the power save mode or when the main power switch and power key are ON, it detects whether or not stain exist at the original reading glass when the DF is closed. This warning will be displayed if the original is set to DF when stain exist. • The thin line detection level and the warning display can be changed by [Service Mode] -> [System 2] -> [ADF Scan Glass Contamin. Set.] -> [Front Side]. |
| Causes: | • Front side cleaning motor (M8) • Front side cleaning home sensor (PS18) • DF control board (DFCB) |
| Remedy: | 1. Wipe clean the glass surface of the original reading glass. 2. Check the front side glass cleaning roller unit for proper installation and correct if necessary. Clean the front side glass cleaning roller unit if dirty. 3. Select [Service Mode] -> [System 2] ->[ADF Scan Glass Contamin. Set.] -> [Front Side], and change the setting. 4. Check the DFCB connector for proper connection and correct as necessary. 5. M8 operation check 6. Replace the front side glass cleaning roller unit. 7. Replace DFCB. |
| Error code: | D-3 |
| Description: | Split line detect (back side). • While recovering from the power save mode or when the main power switch and power key are ON, it detects whether or not stain exist at the back side original scanning section (CIS) when the DF is closed. This warning will be displayed if the original is set to DF when stain exist. • The thin line detection level and the warning display can be changed by [Service Mode] -> [System 2] -> [ADF Scan Glass Contamin. Set.] -> [Back Side]. |
| Causes: | • CIS module (CIS) • DF power supply (DFPU) • Dual scan image processing board (DSIPB) |
| Remedy: | 1. Wipe clean the CIS glass surface. 2. Check the back side glass cleaning roller unit for proper installation and correct if necessary. Clean the back side glass cleaning roller unit if dirty. 3. If there is a problem in the CIS module connection, correct the faulty connection. 4. Replace CIS. 5. Replace DFPU. 6. Replace DSIPB. |
| Error code: | P-14 |
| Description: | Skew correction trouble. The difference between the skew default position setting value and the cumulative amount of skew adjustment values goes over the predetermined value. |
| Causes: | • IDC sensor/Fr (IDCS/Fr) • IDC sensor/Rr (IDCS/Rr) • PH relay board (PHRYB) • MFP board (MFPB) • PH unit • Imaging unit/Y,M,C • Drum unit/K |
| Remedy: | 1. Check the drive transmission portion of the imaging unit and correct as necessary. 2. Clean the contact of the imaging unit connector if dirty. 3. Reinstall or reconnect IDCS/Fr, connectors connecting between IDCS/Fr-relay CN228-MFPB CN32E, and the sensor shutter, if any of the foregoing parts is installed or connected improperly. 4. Reinstall or reconnect IDCS/Rr, connectors connecting between IDCS/Rr-relay CN228-MFPB CN32E, and the sensor shutter, if any of the foregoing parts is installed or connected improperly. 5. Clean IDCS/Fr or IDCS/Rr if it is dirty. 6. Replace IDCS/Fr or IDCS/Rr. 7. Replace the imaging unit/Y,M,C. 8. Replace the drum unit/K. 9. Replace the PH unit. 10. PHRYB ICP3 conduction check. 11. Replace PHRYB. 12. MFPB F3E, F12E, or F13E conduction check 13. Replace MFPB. NOTE . After the PH unit is replaced, reset the skew default position for each color in [Service Mode] -> [Machine] -> [Print Head Skew Adj.] -> [Print Head Skew Adj.] . When this alert code is displayed, according to the list, take actions to address the problem. After the problem is resolved, select [Service Mode] -> [Machine] -> [Print Head Skew Adj.] -> [Print Head Skew Reset] and perform the skew adjustment reset. |
| Error code: | P-21 |
| Description: | Color regist test pattern failure. • During pre-pattern detection, pre-pattern edge (start/ end point of effective area) is not detected within the pre-pattern search area. • During detection of regist pattern at vertical/horizontal direction, pattern edge (start/end point of effective area) is not detected within the pattern search area of each unit. |
| Causes: | • Transfer belt unit • PH unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Wipe clean the surface of the transfer belt with a soft cloth, if it is dirty. 2. Replace the transfer belt unit if the transfer belt is damaged. 3. Replace the PH unit. 4. PHRYB ICP3 conduction check. 5. Replace PHRYB. 6. MFPB F3E conduction check 7. Replace MFPB. |
| Error code: | P-22 |
| Description: | Color regist adjust failure. • The gap between maximum and minimum value of deviations among each color (the values before averaging) is over the predetermined value. • Average deviation exceeds the predetermined value. • In case the final value of the deviation after stabilization exceeds the predetermined value, it is regarded as failure even if the average deviation is within tolerance. |
| Causes: | • IDC sensor/Fr (IDCS/Fr) • IDC sensor/Rr (IDCS/Rr) • IDC sensor shutter solenoid (SD2) • MFP board (MFPB) |
| Remedy: | 1. Slide out the imaging unit and reinstall it in position. 2. Reinstall or reconnect IDCS/Fr, connectors connecting between IDCS/Fr-relay CN228-MFPB CN32E, and the sensor shutter, if any of the foregoing parts is installed or connected improperly. 3. Reinstall or reconnect IDCS/Rr, connectors connecting between IDCS/Rr-relay CN228-MFPB CN32E, and the sensor shutter, if any of the foregoing parts is installed or connected improperly. 4. Check the vertical transport guide for installed position and correct as necessary. 5. Check the connector between SD2-relay CN551-relay CN228-MFPB CN19E for proper connection. 6. Check that the IDC sensor shutter opens and closes properly. 7. MFPB F3E conduction check 8. Replace MFPB. |
| Error code: | P-27 |
| Description: | Secondary transfer ATVC failure. An abnormal average value is detected during an adjustment of the second transfer ATVC value. |
| Causes: | • High voltage unit/2 (HV2) • MFP board (MFPB) • Image transfer entrance guide • 2nd transfer assy • Transfer belt unit |
| Remedy: | 1. Check the contact between the roller opposed to the 2nd transfer roller in the transfer belt unit and the grounding terminal. Clean the joint or correct if necessary. 2. Check the image transfer entrance guide for proper installation and correct if necessary. 3. Check that the spring does not come off during the pressure operation of the transfer roller and correct if necessary. 4. Check the contact at the joint of the 2nd transfer assy and HV2. Clean the joint or correct if necessary. 5. Replace the transfer belt unit. 6. Replace HV2. 7. MFPB F12E conduction check 8. Replace MFPB. |
| Error code: | P-33 |
| Description: | LD malfunction. The DETOUT signal of the LD drive detected malfunction consecutively for the predetermined frequency. |
| Causes: | • Laser diode/Y (LD/Y) • Laser diode/M (LD/M) • Laser diode/C (LD/C) • Laser diode/K (LD/K) • Laser drive board (LDDB) • PH unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Replace the PH unit. 2. Replace PHRYB. 3. Replace MFPB. |
| Error code: | P-5, P-28 |
| Description: | • IDC sensor (front) failure • IDC sensor (rear) failure • When adjusting the IDC sensor, output voltage detected for all eight sample patterns are above specified value. • When adjustment is complete, sensor`s output voltage with selected light intensity is under specified value. • During image stabilization (gamma correction control), detected output value for IDC sensor did not go below threshold (half the value of what is detected by IDC sensor on the belt surface) for three consecutive times (position of the pattern end is not detected). • During image stabilization (gamma correction control), sensor’s output value of each color for hyper 0 gradation after the primary approximation is half the detection level on the belt surface or under. |
| Causes: | • IDC sensor/Fr (IDCS/Fr) • IDC sensor/Rr (IDCS/Rr) • IDC sensor shutter solenoid (SD2) • MFP board (MFPB) • High voltage unit/1 (HV1) • High voltage unit/2 (HV2) • Transfer belt unit |
| Remedy: | 1. Wipe clean the surface of the transfer belt with a soft cloth, if it is dirty. 2. Replace the transfer belt unit if the transfer belt is damaged. 3. Reinstall or reconnect IDCS/Fr, connectors connecting between IDCS/Fr-relay CN228-MFPB CN32E, and the sensor shutter, if any of the foregoing parts is installed or connected improperly. 4. Reinstall or reconnect IDCS/Rr, connectors connecting between IDCS/Rr-relay CN228-MFPB CN32E, and the sensor shutter, if any of the foregoing parts is installed or connected improperly. 5. Clean IDCS/Fr or IDCS/Rr if it is dirty. 6. Check the connector between HV1 CN1, CN2-MFPB CN12E for proper connection. 7. Check the connector between HV2 CN1-MFPB CN13E for proper connection. 8. Check the connector between SD2-relay CN551-relay CN228-MFPB CN19E for proper connection. 9. Check that the IDC sensor shutter opens and closes properly. 10. Open/close the lower front door, run an image stabilization sequence, and select [Service Mode] -> [State Confirmation] -> [Level History 1] to check the IDC value. If the value is 1.0 V or less, replace IDCS/Fr or IDCS/Rr. • IDC1: IDCS/Fr • IDC2: IDCS/Rr 11. Replace HV1. 12. Replace HV2. 13. MFPB F3E, F12E, or F13E conduction check 14. Replace MFPB. |
| Error code: | P-6, P-7, P-8, P-9 |
| Description: | • Cyan imaging unit failure • Magenta imaging unit failure • Yellow imaging unit failure • Black imaging unit failure All density readings taken from the density pattern produced on the transfer belt are equal or under the IDC sensor photo receiver output value during max. density adjustment (Vg/Vdc adjustment). |
| Causes: | • Imaging unit/C • Imaging unit/M • Imaging unit/Y • Drum unit/K • Developing unit/K • Transfer belt unit • High voltage unit/1 (HV1) • High voltage unit/2 (HV2) • IDC sensor/Fr (IDCS/Fr) • IDC sensor/Rr (IDCS/Rr) • MFP board (MFPB) |
| Remedy: | 1. Select [Service Mode] -> [Imaging Process Adjustment] -> [Max Image Density Adj] and, if the setting value is negative, readjust. 2. Check the drive transmission portion of the imaging unit and correct as necessary. 3. Clean the IDC sensor/Fr or IDC sensor/Rr window if dirty. 4. Clean the contact of the imaging unit connector if dirty. 5. Check the connector between HV1 CN1,CN2-MFPB CN12E for proper connection. 6. Check the connector between HV2 CN1-MFPB CN13E for proper connection. 7. Replace the imaging unit/Y,M,C. 8. Replace the drum unit/K. 9. Replace the developing unit/K. 10. Replace the transfer belt unit. 11. Replace HV1. 12. Replace HV2. 13. MFPB F3E, F12E, or F13E conduction check 14. Replace MFPB. |
| Error code: | S-1 |
| Description: | CCD gain adjustment failure. It is detected that the CCD clamp gain adjustment value is faulty. |
| Causes: | • LED exposure unit (LU201) • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB and MFPB if faulty. 2. Check for possible extraneous light and correct as necessary. 3. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 4. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 5. Replace the CCD unit. 6. Replace SCDB. 7. Replace MFPB. |
| Error code: | S-2 |
| Description: | CIS gain adjustment failure. It is detected that the CIS clamp gain adjustment value is faulty. |
| Causes: | • CIS module (CIS) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CIS and DSIPB if faulty. 2. Correct the harness connection between DSIPB and MFPB if faulty. 3. Check for possible extraneous light and correct as necessary. 4. Wipe clean the back side scanning glass surface and shading sheet. 5. Replace CIS. 6. Replace DSIPB. 7. Replace MFPB. |
