Konica-Minolta Magicolor 2490MF

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Число страниц в месяц

35000

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Тип	лазерный/светодиодный
Технология печати	лазерная
Копир
Сканер
Факс
Тип устройства	МФУ
Телефон
Печать фотографий
Размещение	настольный
Область применения	малый офис
Число страниц в месяц	35 000
Цветность печати	цветная
Макс. формат	A4
Принтер
Количество цветов	4
Прямая печать
Время разогрева	75
Двусторонняя печать
Пигментные чернила
Печать без полей
Макс, разрешение для ч/б печати
По Y	600
По X	2 400
Скорость ч/б печати
A4	20
Время выхода первого отпечатка
Ч/б	12
Копир
Шаг масштабирования	0,01
Макс, количество копий за цикл	99
Время выхода первой копии	23
Значение масштаба
Минимальное	0,5
Максимальное	2
Макс, разрешение (ч/б)
По X	600
По Y	600
Скорость ч/б копирования
A4	5
Сканер
Тип сканера	планшетный/протяжный
Емкость устройства автоподачи оригиналов	50
Стандарт TWAIN
Стандарт WIA
Макс. формат оригинала	A4
Устройство автоподачи оригиналов	одностороннее
Тип датчика сканера	ПЗС (CCD)
Макс, размер сканирования
По Y	355
По X	215
Разрешение сканера
По Х	600
Скорость сканирования
Цветн,	21
Цветн,	23
Ч/б	9,4
Расходные материалы
Количество картриджей	4
Ресурс цветного картриджа/тонера	4 500
Ресурс фотобарабана	45 000
Ресурс ч/б картриджа/тонера	4 500
Печать на:
Рулоне
CD/DVD
Фотобумаге
Матовой бумаге
Этикетках
Пленках
Карточках
Глянцевой бумаге
Конвертах
Плотность бумаги
Максимальная	163
Минимальная	64
Факс
Макс, скорость передачи данных	33,6 Кбит/с
PC Fax
Телефон
Автоответчик
Стандарт DECT
Спикерфон
Caller ID
АОН
Беспроводная трубка
Проводная трубка
Языки управления
PCL 6
PCL 5e
PCL 5c
PostScript
PostScript 3
PDF
PPDS
PostScript 2
Лотки
Подача бумаги
Максимальная	700
Стандартная	200
Вывод бумаги
Стандартный	100
Финишер
Сортировка со сдвигом
Сортер
Брошюровщик
Степлер
Электронная сортировка
Интерфейсы
RS-232
FireWire (IEEE 1394)
Wi-Fi
Bluetooth
LPT
Инфракрасный порт
Устройство для чтения карт памяти
Ethernet (RJ-45)
USB
Версия USB	2,0
Память/Процессор
Объем памяти	128
Дополнительная информация
Мин. системные требования
Экран
Поддержка ОС
Windows
Mac OS
DOS
Linux
Потребляемая мощность
В режиме ожидания	250
При работе	1 100
Уровень шума
При работе	57
В режиме ожидания	39
Габариты
Вес	35,2
Высота	531
Глубина	475
Ширина	530

Модули

RIGHT FRAME 2

ELECTRICAL COMPONENTS

PAPER TAKE-UP SECTION 3

VERTICAL TRANSPORT SECTION

MAIN FRAME

DRIVE SECTION 3

ADF 3

PH Section

TRANSFER SECTION

ADF 2

FUSING UNIT

LEFT FRAME

PAPER TAKE-UP SECTION

EXTERNAL PARTS

DRIVE SECTION

RIGHT FRAME

LEFT FRAME 3

ADF

TOP COVER 2

PAPER TAKE-UP SECTION 2

DRIVE SECTION 4

TRANSFER ROLLER SECTION

TOP COVER

IR SECTION

IR SECTION 2

DRIVE SECTION 2

MAIN FRAME 2

LEFT FRAME 2

Детали ADF 2

Деталь:	LEFT COVER
Парткод:	1492 1002 01

Деталь:	SHEET
Парткод:	4980 1046 01

Деталь:	LABEL
Парткод:	1492 1012 01

Деталь:	ADF ASSY
Парткод:	1492 1001 01

Деталь:	GUIDE PLATE
Парткод:	1492 1023 01

Деталь:	PIN
Парткод:	4980 1097 01

Деталь:	BUSHING
Парткод:	4980 1064 01

Деталь:	Gear 33T
Парткод:	4980 1066 01

Деталь:	SHAFT
Парткод:	4980 1067 01

Деталь:	BRACKET
Парткод:	4980 1063 01

Деталь:	BUSHING
Парткод:	4980 1065 01

Деталь:	GEAR 12T
Парткод:	4980 1070 01

Деталь:	SHAFT
Парткод:	4980 1071 01

Деталь:	CLUTCH
Парткод:	1492 1128 01

Деталь:	ROLLER
Парткод:	1391 1033 01

Деталь:	PLATE SPRING
Парткод:	4980 1053 01

Деталь:	GEAR 20T
Парткод:	4980 1072 01

Деталь:	CABLE CLIP
Парткод:	4272 1085 01

Деталь:	ROLLER
Парткод:	1492 1027 01

Деталь:	Gear 23T
Парткод:	4647 1144 01

Деталь:	HOLDER
Парткод:	4980 1059 01

Деталь:	STOPPER
Парткод:	4980 1060 01

Деталь:	Gear 19/23T
Парткод:	4647 1146 01

Деталь:	PICK-UP ROLLER
Парткод:	4980 1008 01

Деталь:	SHAFT
Парткод:	4980 1061 01

Деталь:	TORSION SPRING
Парткод:	1492 1095 01

Деталь:	PLATE SPRING
Парткод:	4980 1055 01

Деталь:	MICRO-SWITCH
Парткод:	4980 1057 01

Деталь:	SHUTTER
Парткод:	4980 1058 01

Деталь:	SHUTTER
Парткод:	4980 1069 01

Деталь:	ACTUATOR
Парткод:	1492 1094 01

Деталь:	SHAFT
Парткод:	4980 1062 01

Деталь:	PHOTO INTERRUPTER
Парткод:	4980 1009 02

Деталь:	CABLE TIE
Парткод:	1492 1112 01

Деталь:	WASHER
Парткод:	1492 1102 01

Деталь:	SPONGE
Парткод:	1492 1099 02

Деталь:	SPONGE
Парткод:	1492 1101 01

Деталь:	SPONGE
Парткод:	1492 1100 01

Деталь:	SPONGE
Парткод:	1492 1115 01

Деталь:	SPONGE
Парткод:	1492 1116 01

Деталь:	SHEET
Парткод:	1492 1103 01

Деталь:	SPONGE
Парткод:	1492 1114 01

Деталь:	SPONGE
Парткод:	1492 1113 01

Деталь:	TUBE
Парткод:	1492 1130 01

Коды ошибок

04H

05H

08H

0BH

0CH

0FH

101H

102H

10H

12H

14H

15H

16H

17H

18H

19H

1AH

1BH

21H

23H

24H

29H

2AH

2BH

2CH

31H

F01H

Деталь:	REGULATING PLATE ASSY
Парткод:	4139 R706 00

Деталь:	LABEL CONSUMABLES REODER
Парткод:	4139 7332 01

Деталь:	Push Button Switch ASSY
Парткод:	4139 R735 00

Деталь:	HUMIDITY CONVERTION EL.
Парткод:	9372 5400 11

Деталь:	LABEL magicolor 2490MF
Парткод:	4556 7323 12

Деталь:	LABEL COPY PROHIBITION
Парткод:	4556 9405 00

Error code:	04H
Description:	Printer control board malfunction • Communications with the M/C expansion IO G/A (IC on the printer control board) are not properly carried out.
Causes:	• CR Encoder failure (contaminated/detached scale, Encoder Board failure) • CR Motor failure • Carriage overload error (paper jam/foreign object) • Cable disconnection
Remedy:	1 Check the PRCB connector for proper connection and correct as necessary. 2 Change PRCB.

Error code:	05H
Description:	Flash ROM malfunction • Engine firmware upgrading has failed.
Causes:	• ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • ADF Motor failure • Paper jam • Cable disconnection
Remedy:	1 Check the PRCB connector for proper connection and correct as necessary. 2 Change PRCB.

Error code:	08H
Description:	Main motor malfunction • The motor lock signal remains HIGH for a predetermined consecutive period of time while the main motor remains energized. • The motor lock signal remains LOW for a predetermined consecutive period of time while the main motor remains deenergized.
Causes:	• CR Encoder failure (contaminated/detached scale, Encoder Board failure) • Tooth skip of the CR Timing Belt • Improper tension of the CR Timing Belt • Paper jam
Remedy:	1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M1 operation check. PRCB PJ8PRCB-5 (REM) PRCB PJ8PRCB-8 (LOCK) C-4. 5 Change PRCB. 6 Change DCPU1.

Error code:	0BH
Description:	Ventilation fan motor malfunction • The fan motor lock signal remains HIGH for a predetermined consecutive period of time while the ventilation fan motor remains energized.
Causes:	• ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • ADF Motor failure • ADF drive overload (paper jam/foreign object) • Cable disconnection
Remedy:	1 Check the FM2 connector for proper connection and correct as necessary. 2 Check FM2 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 FM2 operation check. PRCB PJ10PRCB-1 (REM) PECB PJ10PRCB-3 (LOCK) C-4. 5 Change PRCB. 6 Change DCPU1.

Деталь:	FRICTION SHEET
Парткод:	4136 3049 01

Деталь:	POWER SUPPLY
Парткод:	4139 6210 05

Деталь:	POWER SUPPLY
Парткод:	4139 6211 05

Деталь:	SWITCH
Парткод:	4038 M601 00

Error code:	0CH
Description:	Power supply cooling fan motor malfunction • The fan motor lock signal remains HIGH for a predetermined consecutive period of time while the power supply cooling fan motor remains energized.
Causes:	An error occurred in the CR motor operating sequence
Remedy:	1 Check the FM1 connector for proper connection and correct as necessary. 2 Check FM1 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M1 operation check. PRCB PJ4PRCB-1 (REM) PRCB PJ4PRCB-3 (LOCK) C-2. 5 Change PRCB. 6 Change DCPU1.

Error code:	0FH
Description:	Duplex cooling fan motor malfunction

Error code:	10H
Description:	Polygon motor malfunction • A low motor lock signal is not detected even after the lapse of a predetermined period of time after the polygon motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the polygon motor remains energized.
Causes:	• CIS Unit failure • Scanner Housing failure • Main Board failure
Remedy:	1 Check the cable and connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PRCB.

Error code:	12H
Description:	Laser malfunction • The SOS signal is not detected within a predetermined period of time after the output of a laser has been started. • The SOS signal is never detected in the image area.
Causes:	• Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Pickup Motor driver failure (Main Board failure)
Remedy:	1 Check the cable and connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PRCB.

Error code:	14H
Description:	2nd image transfer pressure /retraction failure • The state of the retraction position sensor/2nd image transfer is not changed from the unblocked to blocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/2nd image transfer is in the unblocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/2nd image transfer is not blocked (roller in the retracted position) within a predetermined period of time after the retraction sequence of the 2nd transfer roller has been started. • The retraction position sensor/2nd image transfer is not unblocked (roller in the pressed position) within a predetermined period of time after the pressure sequence of the 2nd transfer roller has been started.
Causes:	• Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Pickup Motor failure • Pickup drive mechanism (2nd cassette) overload (paper jam/foreign object) • Cable disconnection
Remedy:	1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the SD4 connector for proper connection and correct as necessary. 4 Check the PRCB connector for proper connection and correct as necessary. 5 PS5 sensor check. PRCB PJ14PRCB-3 (ON) J to K-3. 6 SD4 operation check. PRCB PJ11PRCB-2 (REM) J to K-1. 7 M1 operation check. PRCB PJ8PRCB-5 (REM) PRCB PJ8PRCB-8 (LOCK) C-4. 8 Change PRCB.

Error code:	15H
Description:	Cleaning blade pressure /retraction failure • The state of the retraction position sensor/cleaning blade is not changed from the blocked to unblocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/cleaning blade is in the blocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/cleaning blade is not unblocked (blade in the retracted position) within a predetermined period of time after the retraction sequence of the cleaning blade has been started. • The retraction position sensor/cleaning blade is not blocked (blade in the pressed position) within a predetermined period of time after the pressure sequence of the cleaning blade has been started.
Remedy:	1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the SD3 connector for proper connection and correct as necessary. 4 Check the PRCB connector for proper connection and correct as necessary. 5 PS6 sensor check. PRCB PJ9PRCB-11 (ON) C-5. 6 SD3 operation check. PRCB PJ10PRCB-5 (REM) C-3. 7 M1 operation check. PRCB PJ8PRCB-5 (REM) PRCB PJ8PRCB-8 (LOCK) C-4. 8 Change PRCB.

Error code:	16H
Description:	Transfer belt rotation failure • The belt positioning sensor does not detect the transfer belt position detection hole a second time even after the lapse of a predetermined period of time after it has detected one while the transfer belt is rotated.
Causes:	• Pickup drive mechanism (2nd cassette) overload (paper jam/foreign object)
Remedy:	1 Check the PRCB connector for proper connection and correct as necessary. 2 PS4 sensor check. PRCB PJ9PRCB-8 (ON) C-5. 3 Change transfer belt unit. 4 Change PRCB.

Error code:	17H
Description:	Rack rotation failure • The rack positioning sensor is in the blocked state when the rack motor remains deenergized. • The rack positioning sensor is not blocked a second time even after the lapse of a predetermined period of time after it has been blocked once while the rack motor remains energized. • The rack positioning sensor is unable to detect the deceleration control position after the lapse of a given period of time after the rack motor has started while the rack motor is turning. • The count value of the edge of ON signal of the rack positioning sensor during each developing positions are not a predetermined value while the rack motor is turning.
Remedy:	1 Check the M2 connector for proper connection and correct as necessary. 2 Check M2 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 PS3 sensor check. PRCB PJ5PRCB-11 (ON) C-6 5 M2 operation check. PRCB PJ5PRCB-1 to 4 (Pulse Output) C-6 to 7. 6 Change PRCB.

Error code:	18H
Description:	Heating roller warm-up failure • The thermistor does not detect a predetermined temperature value even after the lapse of a predetermined period of time after the current warm-up cycle has been started and the current warm-up cycle is thus not completed.
Causes:	• Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Paper jam
Remedy:	1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU1, and PRCB for proper connection and correct as necessary. 3 Check the lever of the safety switch and correct as necessary. 4 Change the fusing unit. 5 Change PRCB. 6 Change DCPU1.

Error code:	19H
Description:	Abnormally low heating roller temperature • The temperature detected by the thermistor remains lower than a predetermined value for a predetermined period of time.
Causes:	• Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Motor driver failure (Main Board failure)
Remedy:	1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU1, and PRCB for proper connection and correct as necessary. 3 Check the lever of the safety switch and correct as necessary. 4 Change the fusing unit. 5 Change PRCB. 6 Change DCPU1.