Konica-Minolta bizhub 4700P

Рейтинг

Модули

PH, FUSING SECTION

MAIN POWER SUPPLY SECTION

EXTERNAL PARTS, CASSETTE SECTION

REVERSAL, MAIN DRIVE SECTION

Детали REVERSAL, MAIN DRIVE SECTION

Деталь:	TRANSFER ROLLER
Парткод:	A63NPP0Y00

Деталь:	COMPRESSING SPRING
Парткод:	A63NPP2A00

Деталь:	Reverse Assy
Парткод:	A63PPP0F00

Деталь:	Reverse Assy
Парткод:	A63NPP0X00

Деталь:	Holder Kit
Парткод:	A63NPP1N00

Деталь:	Duplex Assy
Парткод:	A63NPP1500

Деталь:	ACM Drive Assy
Парткод:	A63NPP1800

Деталь:	Pick tire Set(2 pcs/set)
Парткод:	A63NPP1000

Деталь:	ACM Assy
Парткод:	A63NPP1600

Деталь:	Paper Feed/Separation Pad Kit
Парткод:	A63NPP1100

Деталь:	GUIDE ASSY
Парткод:	A63NPP1200

Деталь:	MPF Drive Assy
Парткод:	A63NPP1300

Деталь:	Duplex Gear Assy
Парткод:	A63NPP1400

Деталь:	Cartridge Gear Assy
Парткод:	A63NPP1900

Деталь:	Main Drive Motor
Парткод:	A63NPP2B00

Деталь:	MAIN DRIVE ASSY
Парткод:	A63NPP1700

Коды ошибок

111

121

126

132

133

140

146

155

171

31.21 ... 31.25

31.40 ... 31.45

31.46

31.60 ... 31.65

31.66

32.01 ... 32.10

32.11

900

912

940

948

949

950

952

953

954

955

956

956.01

957

958

959

960

961

964

975 ... 979

980 ... 984

990

991

Описание

Парткод

Название

Konica Minolta TNP34 Тонер-картридж UAR

Konica Minolta TNP37 Тонер-картридж

Konica Minolta IUP16 Блок фотобарабана UAR

Konica Minolta IUP17 Блок фотобарабана

Konica Minolta Печь в сборе

Деталь:	Power supply Assy 100V
Парткод:	A63NPP0V00

Деталь:	Power supply Assy 220V
Парткод:	A63NPP0U00

Деталь:	SEPARATION ROLLER ASSY
Парткод:	A63NPP1C00

Деталь:	Cassette Assy/250 Sheet
Парткод:	A63RPP0000

Деталь:	Cassette Assy/550 Sheet
Парткод:	A63NPP0000

Деталь:	Panel Cover/Button Assy
Парткод:	A63RPP0200

Деталь:	Rubber Foot Set(4 pcs/set)
Парткод:	A63NPP1G00

Error code:	111
Display:	SVC 111 ERROR
Description:	Printhead Error
Causes:	Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization
Remedy:	No first Hysnc - magenta Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J11 and J12 on the system board. Go to “System board”. If the cables are connected correctly to the system board and to the printhead assembly, go to “Printhead diagnostics”

Error code:	121
Display:	Service Call 121: Error
Description:	Fuser Error
Causes:	Is cable between PU board andhighvoltage power LSI connected properly?
Remedy:	Wrong fuser lamp - BUR - replace the fuser assembly

Error code:	126
Display:	Turn power OFF and wait 126: Dew error
Description:	Fuser Error
Causes:	Sensor dew error detected.
Remedy:	Fuser open thermistor hot roll

Деталь:	PRINT HEAD ASSY
Парткод:	A63RPP0300

Деталь:	PRINT HEAD ASSY
Парткод:	A63NPP0G00

Деталь:	FUSING UNIT 110V
Парткод:	A63NPP0N00

Деталь:	SENSOR
Парткод:	A63NPP0H00

Error code:	132
Display:	PCB TABLE
Description:	Fuser Error
Remedy:	Fuser cold hot roll

Error code:	133
Display:	SYSTEM HALT (*) 133 : PCB STATION
Description:	Fuser Error
Remedy:	Fuser cold roll - BUR

Error code:	140
Display:	SVC 140 ERROR
Description:	Motor
Remedy:	DC motor accel stall - staging - replace the Staging motor. If this does not fix the problem, replace the “System board”

Error code:	146
Display:	ERROR 146 E-LOG SEQ
Description:	Motor
Remedy:	Autocompensator motor over speed, autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24 If this does not fix the problem, replace the “System board” on page 4-80.

Error code:	155
Display:	Service Call 155: Error
Description:	Misfeed at Tray 1 (MPT): Jam T1 Paper fed from Tray 1 (MPT) did not reach the Registration Sensor on time.
Causes:	• Feed Roller Assembly MPT, PL5.3.20 • Interlock Switch, PL9.1.11 • Registration Sensor, PL4.1.3 • Feed Solenoid, PL5.3.9 • Registration Roller Assembly, PL4.2.1 • Main Drive Assembly, PL8.1.2
Remedy:	1 Check the following for evidence of fault or damage: • Feed Roller Assembly MPT, PL5.3.20 • Tray 1 (MPT) • Registration Sensor, PL4.1.3 • Main Drive Assembly, PL8.1.2 Remove any foreign objects or paper debris from the paper path. Is there any damage? Replace any damaged or excessively worn parts. Go to Step 2. 2 Test the Registration Sensor. Run the Service Diagnostics Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 3. 3 Check the Registration Sensor connection. Is the Registration Sensor connected to the harness? Go to Step 4. Connect the sensor. 4 Check all pins of the REGISNR Harness PL4.1.4 for continuity. 1. Disconnect P/J181 and P/J18. 2. Check continuity between J181 <=> J18. Go to Step 5. Replace the Registration Sensor Harness. 5 Check the Registration Sensor signal. Block the Registration Sensor. Verify the voltage between P/J18-3 <=> P/J18-2 on the Engine Control Board is 0 VDC. Replace Registration Sensor. Go to Step 6. 6 If possible, print a Test Print from Tray 1 (MPT). Does the Main Motor function properly? Go to Step 16 Go to Step 7 7 Test the Main Drive Assembly. Run the Service Diagnostics Main Motor test. Does the Main Motor turn? Replace the Engine Control Board. Go to Step 8. 8 Check for +24 V to the Main Drive Motor 1. Disconnect P/J481. 2. Close the Interlock Switch while testing. Is there +24 V across J481-10 <=> J481-8? Go to Step 12. Go to Step 9. 9 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the Interlock Switch function correctly? Go to Step 11. Go to Step 10. 10 Check for +5 V to the Interlock Switch Disconnect P/J161. Is there +5 V across P161-1 <=> P161-2? Replace the LVPS. Replace the Interlock Switch. 11 Check FAN/PHD/MOT Harness continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481 Replace Main Drive Motor Replace FAN/ PHD/MOT Harness. 12 Check Turn Roller function. 1. Perform Steps 1 ~ 3 on. 2. Open and close the front door. 3. Observe the Turn Roller. Does the Turn Roller turn while the machine is warming up? Go to Step 16. Go to Step 13. 13 Test the Turn Clutch. 1. Run the Service Diagnostics Tray 1 (MPT) Turn Clutch test. 2. Close the Interlock Switch while testing. Does the Turn Clutch function normally? Check that the Clutch doesn’t slip. Check the gears for damage. Go to Step 14. 14 Check for +24 V to the Turn Clutch. 1. Disconnect P/J191. 2. Close the Interlock Switch while testing. Is there +24 V across P191-2 <=> ground? Go to Step 15. Replace the Engine Control Board. 15 Check Turn Clutch resistance. Disconnect P/J191. Is the resistance between J191-1 <=> J191-2 less than 200Ω? Go to Step 16. Replace the Turn Clutch (Part of the Registration Roller Assembly). 16 If possible, print a Test print from Tray 1 (MPT). Check the Feed Gear operation. Does the gear function normally? Check for damage or obstructions in the paper path. Go to Step 17. 17 Test the Feed Solenoid. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Tray 1 (MPT) Feed Solenoid test. Does the Feed Solenoid function normally? Check that the Feed Solenoid spring and stopper disengage correctly. Go to Step 18. 18 Check all pins on the FRONT/DUP Harness PL5.3.28 for continuity. 1. Disconnect P/J132 and P/J13. 2. Check continuity between J13 <=> P132. Go to Step 19. Replace the FRONT/DUP Harness Assembly. 19 Check Feed Solenoid resistance. Disconnect connector P/J132. Is the resistance between J132-1 <=> J132-2 less than 100Ω? Replace the Engine Control Board. Replace the Feed Solenoid.

Error code:	171
Display:	Inspection is required. 171:Error
Description:	Motor
Causes:	Does this error recur?
Remedy:	Mirror motor lock not achieved - cyan - go to “Printhead diagnostics” on page 3-1. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics” on page 3-1.

Error code:	34
Description:	Non-continuous labels are being treated as continuous labels.
Causes:	The printer was not calibrated for the media being used. The printer is configured for continuous media.
Remedy:	Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81.

Error code:	35
Description:	All lights are on, but nothing displays on the LCD, and the printer locks up.
Causes:	Internal electronic or firmware failure.
Remedy:	Turn the printer power off (O) and then on (I). If the printer locks up again, replace the main logic board.

Error code:	41
Display:	Self Diagnostic LSU
Description:	Install or Reseat Fuser, Code 41 Front thermistor open error. This is a cold condition. Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault is performed.
Causes:	• Fuser • Engine Control Board
Remedy:	1 1. Turn OFF power and remove the Fuser Assembly. 2. Measure the resistance between the fuser connector P600-4 and P600-6. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Replace the engine control board. Go to step 3. 3 1. Turn OFF printer power. 2. Check for an open circuit or poor connection between J600-4 to J600-6 to J404A-2. 3. Is the wiring OK? Replace the engine control board. Repair or replace the wiring harness.

Error code:	42
Display:	Self Diagnostic Temperature
Description:	10-352 ERROR 42 FUSER STS (FRONT) WARM TIME FAILURE
Causes:	1. The ‘Open Cover’ microswitch may be stuck or faulty 2. The tab on the front cover may be damaged or broken 3. Check the connector and cables between Switch and main PBA.
Remedy:	Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board.

Konica-Minolta bizhub 4700P

Модули

Детали REVERSAL, MAIN DRIVE SECTION

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	52
Display:	Send Error (POP3)
Description:	Fan Failure One of the two fans has failed resulting in a fatal error.
Causes:	• Rear Fan, PL1.1.19 • Fuser Fan, PL5.3.31
Remedy:	1 Check the fans for damage or debris: • Fuser Fan, PL1.1.19 • Rear Fan, PL5.3.31 Is either fan damaged? Replace the defective fan. Go to Step 3. 2 Replace the defective fan. Does the error persist? Go to Step 3 Complete 3 Test the fans. Run the Service Diagnostics fan tests to isolate the defective fan. Did one of the fans fail? Go to the troubleshooting procedure for the specific fan. If both fans pass, replace the Engine Control Board.

Error code:	54
Display:	Send Error (Wrong Config)
Description:	10-398 ERROR 54 FAN FAILURE
Causes:	· Loose cable connection · Defective ozone fan · Defective IOD2 board · Defective MCTL board
Remedy:	Enter Service Diagnostics Mode. Run the “Fuser Fan” test. Does the Fuser Fan operate? Y↓N→ Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-1 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-4 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-3 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the Fuser Fan. Replace the Fuser Fan Assembly. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-5 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-8 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-7 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the +24 VDC LVPS Fan. Replace the +24 VDC LVPS Fan.

Error code:	80
Display:	ERROR 80 FORMAT
Description:	Engine Logic Board Failure, Code 80
Remedy:	1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete Replace the engine control board or the image processor board.

Error code:	84
Display:	h`********
Description:	Controller to Engine Logic Board Time Failure, Code 84
Remedy:	1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace the engine control board.

Error code:	88
Display:	Paper Jam
Description:	Lower Tray Communication Failure, Code 88
Causes:	• Engine Control Interface Board • Tray module board • Engine Control board
Remedy:	1 Is J668-1 on the tray module board +5 VDC? Go to step 2. Use the wirenets to troubleshoot and repair the open wire. 2 Is J668-3 on the tray module board +24 VDC? Go to step 3. Use the wirenets to troubleshoot and repair the open wire. 3 1. Check the following connectors for continuity: • P669-1 to J534A-15 • P669-2 to J534A-14 • P669-3 to J534A-13 • P669-4 to J534A-12 • P669-5 to J534A-11 • P669-6 to J534A-10 2. Do all checks indicate continuity? Replace in the following order: • engine control interface board • tray module board • engine control board Check and repair broken wires or bad connectors.

Error code:	900
Description:	RIP Software
Remedy:	1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba.

Error code:	912
Description:	DC pick motor underspeed error
Remedy:	• Check system board • Check autocompensator

Error code:	940
Display:	Power Off/on 940: Error
Description:	Waste Toner Transfer Error The Waste Toner Auger Rotation Sensor indicates that the Waste Toner Auger has stopped rotating. Applicable Status Code: Code 940: The Waste Toner Auger has failed.
Causes:	• Waste Toner Auger Rotation Sensor • Waste Toner Auger Assembly • Waste Toner Motor
Remedy:	1 Check the following for evidence of fault or damage: • Waste Toner Manifold • Waste Toner Auger Rotation Sensor • HALLDCT Harness Is there any damage or debris? Replace any damaged parts. Go to Step 2. 2 Test the Waste Toner Auger Rotation Sensor. Run the Service Diagnostics Waste Toner Hole IC test using a magnetic source to actuate the Hall-effect sensor. Does the sensor function correctly? Go to Step 3. Replace the sensor. If the error persists, go to Step 6. 3 Check the Waste Toner Manifold Auger drive. With the Basket Assembly closed, rotate the Waste Toner Motor. Does the Auger rotate? Go to Step 4. Replace the Waste Toner Gear Assembly PL2.1.41. 4 Test the Waste Toner Motor. Run the Service Diagnostics Waste Motor test. Does the motor rotate? Go to Step 7. Replace the motor. If the error persists, go to Step 5. 5 Check all pins of the WTDC Harness for continuity. Disconnect WTDC and P/J50. Is the harness conductive? Replace the Motor Driver Board. Replace the harness. 6 Check all pins of the HALLDCT Harness for continuity. Disconnect HALLDCT and P/J320. Is the harness conductive? Replace the Motor Driver Board. Replace the harness. 7 Check all pins of the DRV0 Harness for continuity. Disconnect DRV0. Is the harness conductive? Replace the Motor Driver Board. If the error persists, replace the Engine Control Board. Replace the harness.

Error code:	948
Description:	PEL Clock Error
Remedy:	Indicates the pel clock check failed. Replace the system board.

Error code:	949
Description:	Delay Line Calibration Failure
Remedy:	Indicates a delay line calibration failure. Replace the system board.