Konica-Minolta bizhub 7828
Рейтинг
Модули
CCD SECTION
MANUAL PAPER FEED SECTION 3
1ST PAPER FEED SECTION
CASSETTE SECTION 3
ELECTRICAL COMPONENTS 2
2ND PAPER FEED SECTION 2
SCANNER DRIVE SECTION
MANUAL PAPER FEED SECTION 4
PAPER TRANSPORT SECTION
EXTERNAL PARTS 2
2ND PAPER FEED SECTION 3
MANUAL PAPER FEED SECTION
CASSETTE SECTION 2
OZONE DUCT, FAN MOTOR SECTION
PAPER EXIT SECTION 2
HOPPER SECTION 2
PAPER TRANSPORT SECTION 3
PAPER TRANSPORT SECTION 4
HOPPER SECTION
FUSING SECTION
SCANNER SECTION
IU SECTION
PRINT HEAD, POWER SUPPLY SECTION
1ST PAPER FEED SECTION 2
IR COVER
ELECTRICAL COMPONENTS
PAPER EXIT SECTION
HOPPER, PAPER FEED DRIVE SECTION
OPERATION PANEL SECTION
CASSETTE SIZE SECTION
IU, CASSETTE RAIL SECTION
CASSETTE SECTION
PAPER TRANSPORT SECTION 2
2ND PAPER FEED SECTION
EXTERNAL PARTS
MANUAL PAPER FEED SECTION 2
REAR FRAME SECTION
MAIN DRIVE SECTION
PAPER TRANSPORT SECTION 5
Детали PAPER TRANSPORT SECTION 5
| Деталь: | Scanner Wiring /4 |
| Парткод: | A1UD N104 00 |
| Деталь: | Scanner Wiring /9 |
| Парткод: | A1UD N109 01 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 81 |
| Деталь: | TAPE |
| Парткод: | 4036 3075 01 |
| Деталь: | GASKET |
| Парткод: | A1UD M902 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A1UD 2790 00 |
| Деталь: | CCD ASSY |
| Парткод: | A1UD R717 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2817 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2625 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 2673 00 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A1UD N100 00 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326 1200 61 |
| Деталь: | SEAL |
| Парткод: | A0ED 2685 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2684 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A00J 2653 00 |
| Деталь: | PWB assembly(PWB-UCN ASSY) |
| Парткод: | A0P0 H025 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 2818 00 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A1UD N140 01 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A1UD N141 01 |
| Деталь: | SEAL |
| Парткод: | A0ED 2632 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2624 00 |
| Деталь: | COVER |
| Парткод: | A0ED 2623 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2627 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2626 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5956 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5952 01 |
| Деталь: | SOLENOID |
| Парткод: | 9J06 M200 00 |
| Деталь: | CLUTCH |
| Парткод: | A1UD M201 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 5955 00 |
| Деталь: | SHIELD PLATE |
| Парткод: | 4038 3237 01 |
| Деталь: | CLUTCH ASSY |
| Парткод: | A02E 5951 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | GEAR 22T |
| Парткод: | A02E 5954 00 |
| Деталь: | CAM |
| Парткод: | A02E 5960 02 |
| Деталь: | SHAFT |
| Парткод: | A02E 5953 02 |
| Деталь: | SHAFT |
| Парткод: | A1UD 5957 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5941 01 |
| Деталь: | COVER |
| Парткод: | A02E 5912 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 5913 00 |
| Деталь: | ROLLER |
| Парткод: | A00F 6232 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 5945 00 |
| Деталь: | LEVER |
| Парткод: | A02E 5946 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A1UD 5959 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5901 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5915 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5902 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5942 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | GEAR 30T |
| Парткод: | A02E 5961 00 |
| Деталь: | CLUTCH |
| Парткод: | A00F M200 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | SHAFT |
| Парткод: | 4040 3096 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A1UD 5606 00 |
| Деталь: | FRAME |
| Парткод: | A1UD 5601 02 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 5649 01 |
| Деталь: | Photoreflector |
| Парткод: | A0ED M501 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1044 00 |
| Деталь: | FRAME |
| Парткод: | A1UD 5641 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1018 01 |
| Деталь: | CLUTCH |
| Парткод: | A02E 5611 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A1UD 5607 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | CUSHION |
| Парткод: | A1UD 5605 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A1UD 5602 00 |
| Деталь: | GEAR 29T |
| Парткод: | 4030 3008 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | Shaft /P |
| Парткод: | A00J 5640 00 |
| Деталь: | SHAFT |
| Парткод: | A1UD 5604 01 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5603 02 |
| Деталь: | SHAFT |
| Парткод: | 4040 3097 01 |
| Деталь: | Paper feed Holder |
| Парткод: | A00J 5601 00 |
| Деталь: | GEAR 30T |
| Парткод: | 4425 3013 01 |
| Деталь: | Paperfeed Wiring /1 |
| Парткод: | A1UE N127 00 |
| Деталь: | Paperfeed Wiring /1 |
| Парткод: | A1UD N127 00 |
| Деталь: | LEVER |
| Парткод: | A1UD 5611 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5668 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3016 12 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A0ED 6209 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 6210 00 |
| Деталь: | CUSHION |
| Парткод: | A02E 6227 00 |
| Деталь: | LABEL CARRYING CAPACITY |
| Парткод: | 4002 7306 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | Rack /Front |
| Парткод: | A0ED 6211 01 |
| Деталь: | KNOB |
| Парткод: | 4037 3204 01 |
| Деталь: | GUIDE |
| Парткод: | 4537 3317 01 |
| Деталь: | Caulking(Regulating Plate/ASSY) |
| Парткод: | A0ED F621 00 |
| Деталь: | WASHER |
| Парткод: | 4011 3021 01 |
| Деталь: | LEVER |
| Парткод: | A0ED 6213 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED 6214 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0ED 6206 01 |
| Деталь: | GEAR 14T |
| Парткод: | A02E 6224 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 6219 01 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | Controller Detection harness |
| Парткод: | A1UD N133 00 |
| Деталь: | GASKET |
| Парткод: | A1UD M903 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1336 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 1373 00 |
| Деталь: | SCREW |
| Парткод: | 4025 2283 01 |
| Деталь: | COVER |
| Парткод: | A1UD 1316 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1318 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1474 01 |
| Деталь: | COVER |
| Парткод: | A0ED 1319 00 |
| Деталь: | SCREW |
| Парткод: | A00J 1396 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1317 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1302 03 |
| Деталь: | Ground Plate spring |
| Парткод: | A1UD 1329 00 |
| Деталь: | Ground Plate spring |
| Парткод: | A1UD 1328 00 |
| Деталь: | SCREW PROTECTION CUSHION/1 |
| Парткод: | 57GA 6156 0 |
| Деталь: | Insulating Film |
| Парткод: | A1UD 1335 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1301 02 |
| Деталь: | SEAL |
| Парткод: | A1UD 1045 00 |
| Деталь: | BUSHING |
| Парткод: | V502 0100 41 |
| Деталь: | After PWB Assembly (PWB-MC ASSY) |
| Парткод: | A1UD P000 01 |
| Деталь: | CLUTCH |
| Парткод: | A00F M200 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A1UD 5606 00 |
| Деталь: | FRAME |
| Парткод: | A1UD 5651 01 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 5649 01 |
| Деталь: | Photoreflector |
| Парткод: | A0ED M501 00 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3016 12 |
| Деталь: | FRAME |
| Парткод: | A1UD 5642 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1033 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | GEAR 29T |
| Парткод: | 4030 3008 01 |
| Деталь: | CUSHION |
| Парткод: | A1UD 5605 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A1UD 5602 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E 5611 00 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | Shaft /P |
| Парткод: | A00J 5640 00 |
| Деталь: | SHAFT |
| Парткод: | A1UD 5604 01 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5603 02 |
| Деталь: | SHAFT |
| Парткод: | 4040 3097 01 |
| Деталь: | Paper feed Holder |
| Парткод: | A00J 5601 00 |
| Деталь: | GEAR 30T |
| Парткод: | 4425 3013 01 |
| Деталь: | Paperfeed Wiring /2 |
| Парткод: | A1UE N128 00 |
| Деталь: | Paperfeed Wiring /2 |
| Парткод: | A1UD N128 00 |
| Деталь: | LEVER |
| Парткод: | A1UD 5611 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5668 01 |
| Деталь: | SHAFT |
| Парткод: | 4040 3096 01 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A1UD 5607 00 |
| Деталь: | FERRITE CORE |
| Парткод: | 4556 M901 00 |
| Деталь: | Scanner Wiring /8 |
| Парткод: | A1UD N108 00 |
| Деталь: | PWB Assembly(PWB-IF ASSY) |
| Парткод: | A1UD H001 00 |
| Деталь: | Scanner Wiring /6 |
| Парткод: | A1UD N106 00 |
| Деталь: | Inverter unit |
| Парткод: | A0ED M410 00 |
| Деталь: | SPACER |
| Парткод: | V502 0100 33 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326 1810 21 |
| Деталь: | Scanner Wiring /1 |
| Парткод: | A1UD N101 00 |
| Деталь: | Stepping motor |
| Парткод: | A02E M10A 00 |
| Деталь: | Belt 210L |
| Парткод: | A0ED 2756 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0903 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 2628 00 |
| Деталь: | PULLEY |
| Парткод: | A0ED 2753 02 |
| Деталь: | LEVER |
| Парткод: | A00J 2802 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4036 1720 01 |
| Деталь: | SHAFT |
| Парткод: | A0ED 2754 00 |
| Деталь: | BEARING |
| Парткод: | A0ED 2765 00 |
| Деталь: | SEAL |
| Парткод: | 4581 1625 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 2622 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 2654 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 2816 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 2616 00 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 2763 00 |
| Деталь: | SEAL |
| Парткод: | A0ED 2633 00 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 61 |
| Деталь: | COVER |
| Парткод: | A0ED 2622 00 |
| Деталь: | Scanner Wiring /2 |
| Парткод: | A1UD N102 00 |
| Деталь: | Pulling Spring |
| Парткод: | A0ED 2757 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 2760 00 |
| Деталь: | SEAL |
| Парткод: | A1UD 2630 00 |
| Деталь: | Pulley 117T |
| Парткод: | A0ED 2755 01 |
| Деталь: | BRAKE |
| Парткод: | A02E 5934 00 |
| Деталь: | BRAKE |
| Парткод: | A02E 5933 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 5924 00 |
| Деталь: | BRAKE |
| Парткод: | A02E 5932 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 5923 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4687 3281 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | A0ED 5922 01 |
| Деталь: | Paperfeed Detection harness /4 |
| Парткод: | A1UD N12C 01 |
| Деталь: | SEAL |
| Парткод: | A1UD 5992 00 |
| Деталь: | SEAL |
| Парткод: | A02E 5937 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5991 00 |
| Деталь: | Photoreflector |
| Парткод: | A0ED M501 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 5990 00 |
| Деталь: | FRICTION PLATE |
| Парткод: | A1UD 5981 00 |
| Деталь: | Caulking Gear Mounting Plate |
| Парткод: | A02E G621 00 |
| Деталь: | GEAR 40T |
| Парткод: | A02E 5983 00 |
| Деталь: | GEAR 20T |
| Парткод: | A02E 5921 00 |
| Деталь: | RESISTOR |
| Парткод: | V801 3000 06 |
| Деталь: | BRACKET |
| Парткод: | A02E 5981 00 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 5935 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A1UD 5928 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 5936 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 5905 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 5919 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A02E 5925 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 5926 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3475 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 5972 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 5971 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5976 00 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | 4034 0151 01 |
| Деталь: | GUIDE |
| Парткод: | A0ED 5993 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 5973 01 |
| Деталь: | SEAL |
| Парткод: | 4030 3489 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4030 3402 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3403 01 |
| Деталь: | CUSHION |
| Парткод: | A0ED 5917 00 |
| Деталь: | Brake Part |
| Парткод: | A0ED 5931 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A0ED 5939 00 |
| Деталь: | SHAFT |
| Парткод: | A1UD 1015 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 1039 00 |
| Деталь: | STOPPER |
| Парткод: | A1UD 1038 00 |
| Деталь: | WIRE |
| Парткод: | A1UD 1037 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A1UD 1013 00 |
| Деталь: | COVER |
| Парткод: | A1UD 8104 00 |
| Деталь: | COVER |
| Парткод: | 4030 1033 01 |
| Деталь: | STOPPER |
| Парткод: | A1UD 7112 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 3511 02 |
| Деталь: | Supporting point Caulking Assy |
| Парткод: | A1UD R7A0 00 |
| Деталь: | SHAFT |
| Парткод: | A1UD 1210 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1052 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1324 00 |
| Деталь: | Reinforce Plate /Right front |
| Парткод: | A1UD 1207 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1641 01 |
| Деталь: | COVER |
| Парткод: | A1UD 1640 01 |
| Деталь: | Label Only connect |
| Парткод: | A00J 9450 00 |
| Деталь: | FILTER |
| Парткод: | A02E 1484 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A1UD 1334 00 |
| Деталь: | Shield cover |
| Парткод: | A1UD 1303 01 |
| Деталь: | Read Cover /Rear |
| Парткод: | A1UD 1613 01 |
| Деталь: | Read Cover |
| Парткод: | A1UD 1713 01 |
| Деталь: | Cover /Right rear |
| Парткод: | A1UD 1626 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1628 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1625 02 |
| Деталь: | Read Cover /Rear |
| Парткод: | A1UD 1612 01 |
| Деталь: | Tray /Left |
| Парткод: | A1UD 1622 02 |
| Деталь: | Cover /Left |
| Парткод: | A1UD 1607 01 |
| Деталь: | Cover /Left |
| Парткод: | A1UD 1606 01 |
| Деталь: | Cover /Rear |
| Парткод: | A1UD 1611 01 |
| Деталь: | Cover /Rear |
| Парткод: | A1UD 1610 01 |
| Деталь: | GASKET |
| Парткод: | A1UD M904 00 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3079 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3080 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3077 01 |
| Деталь: | Holder /S |
| Парткод: | A00J 5647 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | CUSHION |
| Парткод: | A1UD 5631 00 |
| Деталь: | Mounting Plate /S |
| Парткод: | A00J 5646 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5626 00 |
| Деталь: | SEPARATE ROCKING COLLAR |
| Парткод: | 26NA 2030 0 |
| Деталь: | BRACKET |
| Парткод: | 4030 3025 05 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4030 3037 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3017 03 |
| Деталь: | GUIDE |
| Парткод: | 4030 3027 02 |
| Деталь: | SPACER |
| Парткод: | A1UD 5632 00 |
| Деталь: | LEVER |
| Парткод: | 4030 3078 01 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A0ED 5639 00 |
| Деталь: | Torque limiter /S |
| Парткод: | A0P0 5616 00 |
| Деталь: | COVER |
| Парткод: | A1UD 5907 00 |
| Деталь: | Scale |
| Парткод: | A02E 9409 01 |
| Деталь: | Scale |
| Парткод: | A02E 9408 00 |
| Деталь: | Bypass Label |
| Парткод: | A0ED 9402 00 |
| Деталь: | COVER |
| Парткод: | A1UD 5906 00 |
| Деталь: | LIFTING PLATE |
| Парткод: | A0ED 6205 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030 3226 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3206 01 |
| Деталь: | Lifting Shaft |
| Парткод: | A0ED 6316 00 |
| Деталь: | ACTUATOR |
| Парткод: | A0ED 6207 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0ED 6221 00 |
| Деталь: | ROLL |
| Парткод: | A0ED 6234 00 |
| Деталь: | Reinforce Plate /Right rear |
| Парткод: | A0ED 6331 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 6202 00 |
| Деталь: | LOCK LEVER |
| Парткод: | A0ED 6255 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | Caulking(Mounting Plate cassette) |
| Парткод: | A0ED F622 00 |
| Деталь: | Release Lever |
| Парткод: | A0ED 6257 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0ED 6358 01 |
| Деталь: | Paper feed Cassette |
| Парткод: | A0ED 6201 13 |
| Деталь: | LEVER |
| Парткод: | 4002 3108 01 |
| Деталь: | Reinforce Plate /Left rear |
| Парткод: | A0ED 6232 00 |
| Деталь: | REGULATING PLATE ASSY |
| Парткод: | A02E R734 00 |
| Деталь: | GUIDE |
| Парткод: | 4030 3228 12 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 6223 00 |
| Деталь: | 1st Cassette |
| Парткод: | A0ED F623 00 |
| Деталь: | Top plate |
| Парткод: | A1UD 1357 01 |
| Деталь: | Neutralizing Wiring |
| Парткод: | A1UD N12A 00 |
| Деталь: | SEAL |
| Парткод: | A1UD 1361 00 |
| Деталь: | Ozone Duct Assy |
| Парткод: | A1UD R718 00 |
| Деталь: | SEAL |
| Парткод: | A1UD 1364 00 |
| Деталь: | FILTER |
| Парткод: | A1UD 1351 00 |
| Деталь: | Holding Plate |
| Парткод: | A1UD 1353 01 |
| Деталь: | SEAL |
| Парткод: | 4040 2094 01 |
| Деталь: | DUCT |
| Парткод: | 4040 0163 01 |
| Деталь: | FAN MOTOR |
| Парткод: | A1UD M105 00 |
| Деталь: | SEAL |
| Парткод: | A1UD 1307 00 |
| Деталь: | FILTER |
| Парткод: | A02E 1484 00 |
| Деталь: | FAN MOTOR |
| Парткод: | A0ED M105 00 |
| Деталь: | DUCT |
| Парткод: | A1UD 1313 00 |
| Деталь: | SEAL |
| Парткод: | 4040 2095 01 |
| Деталь: | DUCT |
| Парткод: | A1UD 1309 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | Stepping motor |
| Парткод: | A1UD M101 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A1UD 8928 00 |
| Деталь: | Torsion Coil spring /1 |
| Парткод: | A1UD 8918 00 |
| Деталь: | Torsion Coil spring /2 |
| Парткод: | A1UD 8916 00 |
| Деталь: | Lever /1 |
| Парткод: | A1UD 8911 00 |
| Деталь: | Lever /2 |
| Парткод: | A1UD 8915 00 |
| Деталь: | ROLL |
| Парткод: | A1UD 8929 00 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | A1UD 8910 00 |
| Деталь: | SHAFT |
| Парткод: | 4025 5984 01 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A1UD 8906 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 8152 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 8922 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 8902 01 |
| Деталь: | PULLEY |
| Парткод: | A1UD 8926 00 |
| Деталь: | TIMING BELT |
| Парткод: | A1UD 8927 00 |
| Деталь: | CONNECTOR |
| Парткод: | V651 0100 01 |
| Деталь: | SEAL |
| Парткод: | 4030 5385 02 |
| Деталь: | SHUTTER |
| Парткод: | 1165 5308 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1165 5309 02 |
| Деталь: | SWITCH |
| Парткод: | 9334 2710 11 |
| Деталь: | PLATE NUT |
| Парткод: | 4011 5339 01 |
| Деталь: | GEAR 14/19T |
| Парткод: | 4030 5379 01 |
| Деталь: | Toner supply Gear |
| Парткод: | A1UD 4008 01 |
| Деталь: | Stepping motor |
| Парткод: | A02E M104 00 |
| Деталь: | Toner supply Gear |
| Парткод: | A1UD 4009 00 |
| Деталь: | Toner supply Gear |
| Парткод: | A1UD 4007 00 |
| Деталь: | Sub Hopper Assy |
| Парткод: | A1UD R704 11 |
| Деталь: | Supply Drive harness |
| Парткод: | A1UD N125 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1024 01 |
| Деталь: | GUIDE |
| Парткод: | A1UD 8127 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A1UD 7118 00 |
| Деталь: | Holding Part |
| Парткод: | A1UD 8141 00 |
| Деталь: | ROLL |
| Парткод: | 4497 3116 01 |
| Деталь: | GUIDE |
| Парткод: | A1UD 8109 00 |
| Деталь: | Conveyance Detection harness |
| Парткод: | A1UD N132 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108 R900 00 |
| Деталь: | HOLDER |
| Парткод: | A1UD 7003 00 |
| Деталь: | HOLDER |
| Парткод: | A1UD 7107 00 |
| Деталь: | CONTACT |
| Парткод: | A1UD 7120 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4011 3515 01 |
| Деталь: | BRACKET |
| Парткод: | 1164 3529 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3504 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 1164 3527 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 4207 01 |
| Деталь: | BUSHING |
| Парткод: | 1164 4206 02 |
| Деталь: | CONTACT |
| Парткод: | 1164 4209 02 |
| Деталь: | CONTACT |
| Парткод: | A1UD 7130 00 |
| Деталь: | HOLDER |
| Парткод: | 1164 4218 01 |
| Деталь: | BUSHING |
| Парткод: | 1164 3549 01 |
| Деталь: | GEAR 18T |
| Парткод: | 1164 3508 01 |
| Деталь: | GEAR 13T |
| Парткод: | 1164 3515 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 1164 3514 02 |
| Деталь: | TENSION SPRING |
| Парткод: | 1164 3513 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3505 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 4213 02 |
| Деталь: | THERMISTOR |
| Парткод: | 9372 2710 22 |
| Деталь: | NEUTRALIZING NEEDLE |
| Парткод: | 1164 4202 04 |
| Деталь: | WASHER |
| Парткод: | 4011 3512 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3020 01 |
| Деталь: | CLUTCH |
| Парткод: | A1UD M200 00 |
| Деталь: | ROLLER |
| Парткод: | A1UD 7002 00 |
| Деталь: | ROLLER |
| Парткод: | 4011 3509 01 |
| Деталь: | PAPER DUST REMOVER |
| Парткод: | 4040 0778 00 |
| Деталь: | HOLDER |
| Парткод: | 4030 3501 09 |
| Деталь: | FIXED POWER RESISTORS |
| Парткод: | V800 5003 00 |
| Деталь: | CONTACT |
| Парткод: | 4030 4220 01 |
| Деталь: | TRANSFER ROLLER ASSY |
| Парткод: | A1UD R705 00 |
| Деталь: | ROLLER |
| Парткод: | A1UD 8105 00 |
| Деталь: | ROLL |
| Парткод: | 4497 3116 01 |
| Деталь: | GROUND PLATE |
| Парткод: | A1UD 8123 00 |
| Деталь: | ADU Relay harness |
| Парткод: | A1UD N12P 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108 R900 00 |
| Деталь: | BRACKET |
| Парткод: | 4030 3742 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3740 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 3741 03 |
| Деталь: | GUIDE |
| Парткод: | A1UD 8134 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 8111 00 |
| Деталь: | Holding Part |
| Парткод: | A1UD 8141 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 8128 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 8152 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 8116 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A1UD 8126 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 8108 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 8137 00 |
| Деталь: | Ground Part |
| Парткод: | A1UD 8142 01 |
| Деталь: | HOPPER ASSY |
| Парткод: | A1UF R700 00 |
| Деталь: | HOPPER ASSY |
| Парткод: | A1UD R714 00 |
| Деталь: | HOPPER ASSY |
| Парткод: | A1UF R701 00 |
| Деталь: | HOPPER ASSY |
| Парткод: | A1UD R715 00 |
| Деталь: | HOPPER ASSY |
| Парткод: | A1UF R702 00 |
| Деталь: | HOPPER ASSY |
| Парткод: | A1UD R716 00 |
| Деталь: | SUPPORT |
| Парткод: | 1151 5023 01 |
| Деталь: | JOINT |
| Парткод: | A1UD 4107 00 |
| Деталь: | STOPPER |
| Парткод: | 4030 5387 02 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 5388 01 |
| Деталь: | HOLDER |
| Парткод: | 4030 5380 01 |
| Деталь: | PIN |
| Парткод: | 1165 5325 01 |
| Деталь: | SEAL |
| Парткод: | 1165 5327 03 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A1UD 4110 00 |
| Деталь: | COLLAR |
| Парткод: | A1UD 4108 00 |
| Деталь: | CUSHION |
| Парткод: | A1UD 4109 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A1UD 4103 00 |
| Деталь: | LABEL |
| Парткод: | A1UF 9406 00 |
| Деталь: | LABEL |
| Парткод: | A1UD 9406 00 |
| Деталь: | STOPPER |
| Парткод: | A1UD 4101 00 |
| Деталь: | HANDLE |
| Парткод: | 4030 5393 01 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A1UD 4104 00 |
| Деталь: | HANDLE |
| Парткод: | A1UD 4106 00 |
| Деталь: | SCREW |
| Парткод: | 1250 2301 01 |
| Деталь: | CLAW |
| Парткод: | A1UD 4102 00 |
| Деталь: | STOPPER |
| Парткод: | A1UD 1028 01 |
| Деталь: | SEESAW-SWITCH |
| Парткод: | 4038 M600 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4030 5396 01 |
| Деталь: | AC Power source harness |
| Парткод: | A1UD N113 00 |
| Деталь: | Light blocking Sheet |
| Парткод: | A1UD 1034 01 |
| Деталь: | COLLAR |
| Парткод: | 4030 5398 01 |
| Деталь: | SHUTTER |
| Парткод: | 4030 5383 02 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 5386 01 |
| Деталь: | SEAL |
| Парткод: | 4030 5384 01 |
| Деталь: | STOPPER |
| Парткод: | 4040 5322 01 |
| Деталь: | STOPPER |
| Парткод: | 4011 5347 01 |
| Деталь: | Fusing Unit 100V |
| Парткод: | A1UD R708 00 |
| Деталь: | FUSING UNIT 120V |
| Парткод: | A1UD R709 00 |
| Деталь: | FUSING UNIT 200V |
| Парткод: | A1UD R710 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2707 00 |
| Деталь: | Pressing Plate |
| Парткод: | A0ED 2709 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 2706 00 |
| Деталь: | Lamp |
| Парткод: | A0ED M310 00 |
| Деталь: | SEAL |
| Парткод: | A02E 2708 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 2705 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED 2713 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2708 00 |
| Деталь: | MIRROR |
| Парткод: | A0ED 2712 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2704 00 |
| Деталь: | 1st Slider Assy |
| Парткод: | A0ED R728 00 |
| Деталь: | WIRE |
| Парткод: | A0ED 2751 00 |
| Деталь: | PULLEY |
| Парткод: | A0ED 2736 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2737 00 |
| Деталь: | GUIDE |
| Парткод: | A0ED 2812 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2762 00 |
| Деталь: | Pulling Spring |
| Парткод: | A0ED 2763 01 |
| Деталь: | GUIDE PART |
| Парткод: | A0ED 2740 00 |
| Деталь: | PULLEY |
| Парткод: | A0ED 2739 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2734 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A0ED 2744 00 |
| Деталь: | Vibrationproof Plate |
| Парткод: | A0ED 2742 00 |
| Деталь: | MIRROR |
| Парткод: | A0ED 2743 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 2733 00 |
| Деталь: | WIRE |
| Парткод: | A0ED 2752 00 |
| Деталь: | SEAL |
| Парткод: | 4040 5260 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 1139 5249 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 1139 5250 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4163 5210 02 |
| Деталь: | SEAL |
| Парткод: | 4163 5238 01 |
| Деталь: | SEAL |
| Парткод: | 4163 5208 01 |
| Деталь: | SHUTTER |
| Парткод: | 4163 5205 01 |
| Деталь: | ROLL |
| Парткод: | 4163 5298 01 |
| Деталь: | HOLDER |
| Парткод: | 4163 5226 01 |
| Деталь: | SEAL |
| Парткод: | 4021 5225 01 |
| Деталь: | WASHER |
| Парткод: | 4661 3155 01 |
| Деталь: | SEAL |
| Парткод: | 4163 5221 01 |
| Деталь: | SEAL |
| Парткод: | 4163 5207 01 |
| Деталь: | SEAL |
| Парткод: | 4163 5237 01 |
| Деталь: | SEAL |
| Парткод: | 4163 5209 01 |
| Деталь: | SEAL |
| Парткод: | 4163 5240 01 |
| Деталь: | SEAL |
| Парткод: | 4163 5239 01 |
| Деталь: | GEAR |
| Парткод: | A1UD 3710 00 |
| Деталь: | Panel heater Kit |
| Парткод: | A1UD R900 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 3709 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4163 5231 02 |
| Деталь: | GEAR 20T |
| Парткод: | 4163 5224 01 |
| Деталь: | COVER |
| Парткод: | 4040 5222 01 |
| Деталь: | SEAL |
| Парткод: | 4040 5223 01 |
| Деталь: | FILTER |
| Парткод: | A1UD 3707 00 |
| Деталь: | PWB Assembly(PWB-TCR ASSY) |
| Парткод: | A0TK H002 00 |
| Деталь: | SEAL |
| Парткод: | A1UD 3706 01 |
| Деталь: | HOLDER |
| Парткод: | A1UD 3705 00 |
| Деталь: | SEAL |
| Парткод: | 4040 5211 01 |
| Деталь: | DEVELOPING UNIT |
| Парткод: | A1UD R711 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1040 01 |
| Деталь: | HOLDER |
| Парткод: | A1UD 1041 01 |
| Деталь: | COVER |
| Парткод: | A1UD 1042 01 |
| Деталь: | COVER |
| Парткод: | A1UD 1310 00 |
| Деталь: | HIGH VOLTAGE UNIT |
| Парткод: | A1UD M403 01 |
| Деталь: | Heater Relay harness /1 |
| Парткод: | A1UD N116 00 |
| Деталь: | BRACKET |
| Парткод: | 4030 2040 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4128 1978 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4128 1979 01 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | A1UF R703 00 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | A1UD R713 00 |
| Деталь: | SEAL |
| Парткод: | A1UD 1045 00 |
| Деталь: | POWER SUPPLY |
| Парткод: | A1UD M400 02 |
| Деталь: | POWER SUPPLY |
| Парткод: | A1UD M401 02 |
| Деталь: | POWER SUPPLY |
| Парткод: | A1UD M402 02 |
| Деталь: | SEAL |
| Парткод: | A1UD 1026 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A1UD 1006 01 |
| Деталь: | CONNECTOR |
| Парткод: | V651 0100 02 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A1UD 1206 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3079 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3080 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3077 01 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A0ED 5639 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | Holder /S |
| Парткод: | A00J 5647 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | CUSHION |
| Парткод: | A1UD 5631 00 |
| Деталь: | Mounting Plate /S |
| Парткод: | A00J 5646 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5626 00 |
| Деталь: | BRACKET |
| Парткод: | 4030 3025 05 |
| Деталь: | SCREW PROTECTION CUSHION/1 |
| Парткод: | 57GA 6156 0 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A1UD 5646 00 |
| Деталь: | SEPARATE ROCKING COLLAR |
| Парткод: | 26NA 2030 0 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4030 3037 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3017 03 |
| Деталь: | SPACER |
| Парткод: | A1UD 5632 00 |
| Деталь: | LEVER |
| Парткод: | 4030 3078 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3027 02 |
| Деталь: | Torque limiter /S |
| Парткод: | A0P0 5616 00 |
| Деталь: | Label Print Side |
| Парткод: | A0ED 9403 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 1692 00 |
| Деталь: | LABEL |
| Парткод: | A00J 9402 00 |
| Деталь: | Label Legal Restiriction |
| Парткод: | A00J 9401 00 |
| Деталь: | Holding Plate |
| Парткод: | A0ED 2683 00 |
| Деталь: | ORIGINAL GLASS ASSY |
| Парткод: | A0ED R727 00 |
| Деталь: | Read Cover /Right rear |
| Парткод: | A1UD 1705 00 |
| Деталь: | COVER |
| Парткод: | A02E 1677 00 |
| Деталь: | Read Cover /Right |
| Парткод: | A1UD 1704 00 |
| Деталь: | COVER |
| Парткод: | A00J 1691 00 |
| Деталь: | Read Cover |
| Парткод: | A1UD 1711 01 |
| Деталь: | Read Cover |
| Парткод: | A1UD 1715 00 |
| Деталь: | Read Cover /Front |
| Парткод: | A0ED 1701 00 |
| Деталь: | REED SWITCH |
| Парткод: | 9334 2610 12 |
| Деталь: | Light blocking Plate |
| Парткод: | A00J 1689 02 |
| Деталь: | Lens /B |
| Парткод: | A00J 1682 02 |
| Деталь: | Light blocking Cover /C |
| Парткод: | A00J 1685 03 |
| Деталь: | PWB Assembly LED2 |
| Парткод: | A00J H00E 00 |
| Деталь: | Scanner Wiring /5 |
| Парткод: | A0ED N145 00 |
| Деталь: | Holding Plate |
| Парткод: | A0ED 2688 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 2681 00 |
| Деталь: | Slit Glass Assy |
| Парткод: | A1UD R703 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0ED 2687 00 |
| Деталь: | COVER |
| Парткод: | A0ED 2675 00 |
| Деталь: | Read Cover /Left |
| Парткод: | A1UD 1703 02 |
| Деталь: | Cover /Rear |
| Парткод: | A1UD 1717 00 |
| Деталь: | Read Cover /Rear |
| Парткод: | A1UD 1702 00 |
| Деталь: | Read Cover |
| Парткод: | A1UD 1707 00 |
| Деталь: | Holding Plate |
| Парткод: | A0ED 2682 00 |
| Деталь: | Read Cover Upper F |
| Парткод: | A0ED 1706 00 |
| Деталь: | HDD |
| Парткод: | A0ED M720 00 |
| Деталь: | CABLE |
| Парткод: | A0P0 N152 00 |
| Деталь: | CABLE |
| Парткод: | A0P0 N151 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0 1443 00 |
| Деталь: | BUSHING |
| Парткод: | A0P0 1444 00 |
| Деталь: | Ground Plate spring |
| Парткод: | A1UD 1332 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1473 00 |
| Деталь: | MEMORY MODULES |
| Парткод: | V865 3000 26 |
| Деталь: | CUSHION |
| Парткод: | 4004 1829 02 |
| Деталь: | GROUND PLATE |
| Парткод: | A1UD 1323 00 |
| Деталь: | RAIL |
| Парткод: | A1UD 1308 00 |
| Деталь: | RAIL |
| Парткод: | A0P0 1447 01 |
| Деталь: | PWB assembly (PWB-MFP ASSY) |
| Парткод: | A1UD H020 02 |
| Деталь: | PWB assembly (PWB-MFP ASSY) |
| Парткод: | A1UD H021 02 |
| Деталь: | Ground Plate spring |
| Парткод: | A1UD 1333 00 |
| Деталь: | Cooling Relay harness |
| Парткод: | A1UD N12Y 00 |
| Деталь: | Control Power source harness |
| Парткод: | A1UD N12R 00 |
| Деталь: | Controller Control harness |
| Парткод: | A1UD N12W 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1306 00 |
| Деталь: | Connecting Plate |
| Парткод: | A1UD 1401 02 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1400 02 |
| Деталь: | LABEL |
| Парткод: | A1UD 9414 00 |
| Деталь: | COVER |
| Парткод: | A1UD 8901 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 4556 M100 00 |
| Деталь: | Ground Plate /Upper |
| Парткод: | A1UD 8907 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A1UD 8908 00 |
| Деталь: | Mounting Plate /Front |
| Парткод: | A1UD 8921 00 |
| Деталь: | Ground Plate /Lower |
| Парткод: | A1UD 8905 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 8904 01 |
| Деталь: | ADU Wiring |
| Парткод: | A1UD N12E 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | 4038 5856 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 2189 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | HOLDER |
| Парткод: | A1UD 2186 01 |
| Деталь: | Hopper Drive Motor Assy |
| Парткод: | A1UD R702 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 2181 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 2182 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 2187 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 2183 01 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A1UD 2185 00 |
| Деталь: | JOINT |
| Парткод: | A1UD 2184 00 |
| Деталь: | WASHER |
| Парткод: | A1UD 2190 00 |
| Деталь: | HOPPER DRIVE ASSY |
| Парткод: | A1UD R701 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 2114 01 |
| Деталь: | GEAR |
| Парткод: | A1UD 2103 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 2104 01 |
| Деталь: | GEAR |
| Парткод: | A1UD 2102 01 |
| Деталь: | GEAR |
| Парткод: | A1UD 2106 01 |
| Деталь: | HOLDER |
| Парткод: | A1UD 2100 01 |
| Деталь: | GEAR |
| Парткод: | A1UD 2109 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 2113 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 2120 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 2105 00 |
| Деталь: | GEAR |
| Парткод: | A1UE 2107 00 |
| Деталь: | GEAR |
| Парткод: | A1UE 2108 00 |
| Деталь: | GEAR |
| Парткод: | A1UE 2110 00 |
| Деталь: | HOLDER |
| Парткод: | A1UE 2101 01 |
| Деталь: | Read Cover |
| Парткод: | A1UD 1716 00 |
| Деталь: | Read Cover /Inside |
| Парткод: | A1UD 1712 02 |
| Деталь: | Read Cover |
| Парткод: | A1UD 1714 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M705 03 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M706 03 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M707 03 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M708 02 |
| Деталь: | Ope.unit Cable |
| Парткод: | A1UD N12D 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1679 00 |
| Деталь: | Shoulder screw /1 |
| Парткод: | A1UD 1922 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A1UD 1927 00 |
| Деталь: | WASHER |
| Парткод: | A1UD 1920 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1915 00 |
| Деталь: | Shoulder screw /2 |
| Парткод: | A1UD 1924 00 |
| Деталь: | WASHER |
| Парткод: | A1UD 1929 00 |
| Деталь: | ARM |
| Парткод: | A1UD 1914 00 |
| Деталь: | HANDLE |
| Парткод: | A1UD 1925 00 |
| Деталь: | LEVER |
| Парткод: | A1UD 1923 00 |
| Деталь: | Pulling Spring |
| Парткод: | A0ED 1926 00 |
| Деталь: | ARM |
| Парткод: | A1UD 1913 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1694 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1916 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1680 00 |
| Деталь: | Support Shaft |
| Парткод: | A1UD 1928 00 |
| Деталь: | Read Cover /Right front |
| Парткод: | A1UD 1710 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1912 00 |
| Деталь: | WASHER |
| Парткод: | A00J 1919 00 |
| Деталь: | COLLAR |
| Парткод: | A00J 1917 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1911 00 |
| Деталь: | Support Screw |
| Парткод: | A00J 1918 00 |
| Деталь: | STOPPER |
| Парткод: | A1UD 1930 00 |
| Деталь: | Paperfeed Detection harness /1 |
| Парткод: | A1UD N12K 01 |
| Деталь: | HOLDER |
| Парткод: | 4011 3012 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4002 3131 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4002 3110 01 |
| Деталь: | MOTOR |
| Парткод: | 9J06 M103 00 |
| Деталь: | HOLDER |
| Парткод: | A0ED 6275 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | HOLDER |
| Парткод: | 4030 3083 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3081 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030 3224 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108 R900 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 6346 00 |
| Деталь: | LEVER |
| Парткод: | 4030 3091 01 |
| Деталь: | PWB ASSY |
| Парткод: | 4037 0104 01 |
| Деталь: | Paperfeed Detection harness /2 |
| Парткод: | A1UD N12M 01 |
| Деталь: | Chaging Wiring |
| Парткод: | A1UD N12H 00 |
| Деталь: | HOLDER |
| Парткод: | 4030 2102 01 |
| Деталь: | CONTACT |
| Парткод: | 4030 2115 01 |
| Деталь: | CONTACT |
| Парткод: | 4030 2113 01 |
| Деталь: | CONTACT |
| Парткод: | 4030 2112 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4011 2134 01 |
| Деталь: | Separating Wiring |
| Парткод: | A1UD N12J 00 |
| Деталь: | CONTACT |
| Парткод: | 1165 2153 01 |
| Деталь: | Developing Wiring |
| Парткод: | A1UD N12G 00 |
| Деталь: | LABEL HI-VOL CAUTION |
| Парткод: | 1129 7303 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 2019 03 |
| Деталь: | SEAL |
| Парткод: | 4011 2047 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 1164 2021 02 |
| Деталь: | EARTH GROUND |
| Парткод: | 1165 2142 01 |
| Деталь: | LOUDSPEAKER |
| Парткод: | 4040 M401 00 |
| Деталь: | Transfer Wiring |
| Парткод: | A1UD N12F 00 |
| Деталь: | CONTACT |
| Парткод: | 1164 2155 01 |
| Деталь: | HOLDER |
| Парткод: | A1UD 1053 02 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1314 00 |
| Деталь: | Fixing Relay harness /100V |
| Парткод: | A1UD N114 00 |
| Деталь: | Fixing Relay harness |
| Парткод: | A1UD N115 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1321 00 |
| Деталь: | RAIL |
| Парткод: | A1UD 1007 01 |
| Деталь: | GUIDE |
| Парткод: | A1UD 1025 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A1UD 1050 01 |
| Деталь: | STOPPER |
| Парткод: | A1UD 1016 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 1060 01 |
| Деталь: | RAIL |
| Парткод: | A1UD 1008 02 |
| Деталь: | SPACER |
| Парткод: | 4030 2081 01 |
| Деталь: | CONTACT |
| Парткод: | 4030 2114 01 |
| Деталь: | Label FD |
| Парткод: | A00J 9422 02 |
| Деталь: | Label FD |
| Парткод: | A02E 9413 00 |
| Деталь: | Label Cd |
| Парткод: | A02E 9415 00 |
| Деталь: | HOLDER |
| Парткод: | A1UD 6253 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0ED 6254 00 |
| Деталь: | LABEL PAPER |
| Парткод: | A0ED 9401 00 |
| Деталь: | COVER |
| Парткод: | A1UD 6251 01 |
| Деталь: | HANDLE |
| Парткод: | A0ED 6252 01 |
| Деталь: | COVER |
| Парткод: | A0ED 6250 00 |
| Деталь: | COVER |
| Парткод: | A1UD 6351 01 |
| Деталь: | HOLDER |
| Парткод: | A0ED 6253 01 |
| Деталь: | STOPPER |
| Парткод: | A1UD 8110 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A1UD 8140 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4066 3705 01 |
| Деталь: | HANDLE |
| Парткод: | A1UD 8103 00 |
| Деталь: | COVER |
| Парткод: | A1UD 8101 00 |
| Деталь: | DOOR |
| Парткод: | A1UD 8102 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 7125 00 |
| Деталь: | WASHER |
| Парткод: | 4661 3155 01 |
| Деталь: | PIN |
| Парткод: | A11U 8150 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 7101 01 |
| Деталь: | Ground Part |
| Парткод: | A1UD 7119 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A1UD 8122 00 |
| Деталь: | SEAL |
| Парткод: | A1UD 7123 00 |
| Деталь: | SEAL |
| Парткод: | A1UD 7127 00 |
| Деталь: | GUIDE |
| Парткод: | 4012 3524 12 |
| Деталь: | SEAL |
| Парткод: | A1UD 7121 00 |
| Деталь: | Lock Claw /Front |
| Парткод: | A1UD 7103 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A1UD 7113 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 7105 00 |
| Деталь: | CLAW |
| Парткод: | A1UD 7104 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 7110 00 |
| Деталь: | SEAL |
| Парткод: | A1UD 7122 00 |
| Деталь: | LABEL HI-TEMP CAUTION |
| Парткод: | 4138 5866 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A1UD 7108 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A1UD 7128 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 7111 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 7102 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A1UD 7109 00 |
| Деталь: | ACTUATOR |
| Парткод: | A1UD 8129 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 8131 00 |
| Деталь: | Vertical Conveyance Assy |
| Парткод: | A1UD R707 00 |
| Деталь: | CLUTCH |
| Парткод: | A1UD M201 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | FRAME |
| Парткод: | A1UD 5644 01 |
| Деталь: | ROLLER |
| Парткод: | A1UD 5621 00 |
| Деталь: | WEIGHT |
| Парткод: | A1UD 5614 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4030 3112 02 |
| Деталь: | GUIDE PLATE |
| Парткод: | A1UD 5612 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5724 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5705 00 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3125 01 |
| Деталь: | FRAME |
| Парткод: | A1UD 5643 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 5618 01 |
| Деталь: | PIN |
| Парткод: | 1200 5212 04 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 3031 01 |
| Деталь: | Conveyance Actuator |
| Парткод: | A1UD 5616 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | Conveyance Drive harness /2 |
| Парткод: | A1UE N124 00 |
| Деталь: | COLLAR |
| Парткод: | 1134 3041 01 |
| Деталь: | Photoreflector |
| Парткод: | A0ED M501 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 5619 00 |
| Деталь: | Conveyance Drive harness /2 |
| Парткод: | A1UD N124 00 |
| Деталь: | GUIDE |
| Парткод: | 4030 3108 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3032 03 |
| Деталь: | CUSHION |
| Парткод: | A1UD 5615 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 5703 00 |
| Деталь: | GUIDE |
| Парткод: | A1UD 5704 00 |
| Деталь: | TRAY |
| Парткод: | A0ED 1610 01 |
| Деталь: | Cover /Upper |
| Парткод: | A1UD 1620 01 |
| Деталь: | Label Jam/Adu |
| Парткод: | A02E 9417 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1618 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1615 00 |
| Деталь: | PWB Assembly LED1 |
| Парткод: | A00J H00D 00 |
| Деталь: | Light blocking Cover |
| Парткод: | A00J 1683 01 |
| Деталь: | LENS |
| Парткод: | A0ED 1626 00 |
| Деталь: | Light blocking Plate |
| Парткод: | A0ED 1627 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1630 02 |
| Деталь: | BRACKET |
| Парткод: | 9J06 3235 01 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | CUSHION |
| Парткод: | A1UD 1061 00 |
| Деталь: | COVER |
| Парткод: | A1UD 1609 01 |
| Деталь: | Label Emperon |
| Парткод: | A011 9462 00 |
| Деталь: | LABEL |
| Парткод: | A0ED 9465 00 |
| Деталь: | LABEL |
| Парткод: | A1UD 9413 00 |
| Деталь: | Cover /Front |
| Парткод: | A1UD 1601 02 |
| Деталь: | STOPPER RING |
| Парткод: | 1033 4402 03 |
| Деталь: | Logo Mark |
| Парткод: | A00J 9455 00 |
| Деталь: | Cover /Left front |
| Парткод: | A1UD 1603 00 |
| Деталь: | Cover /Front |
| Парткод: | A1UD 1605 01 |
| Деталь: | Cover /Front |
| Парткод: | A1UD 1602 02 |
| Деталь: | Indicating Wiring |
| Парткод: | A1UD N126 01 |
| Деталь: | LABEL |
| Парткод: | A1UG 9422 00 |
| Деталь: | LABEL |
| Парткод: | A1UF 9422 00 |
| Деталь: | LABEL |
| Парткод: | A1UE 9422 00 |
| Деталь: | LABEL |
| Парткод: | A1UD 9422 00 |
| Деталь: | LABEL |
| Парткод: | A1UF 9425 00 |
| Деталь: | Label Number 1 |
| Парткод: | A02E 9418 00 |
| Деталь: | Label Number 2 |
| Парткод: | A02E 9419 00 |
| Деталь: | COVER |
| Парткод: | A0ED 5909 00 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 5984 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 3446 01 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | SHAFT |
| Парткод: | 1134 3042 02 |
| Деталь: | HOLDER |
| Парткод: | A0ED 5987 00 |
| Деталь: | COVER |
| Парткод: | A02E 5918 01 |
| Деталь: | TRAY |
| Парткод: | A0ED 5908 00 |
| Деталь: | BRACKET |
| Парткод: | 9J06 3235 01 |
| Деталь: | SEAL |
| Парткод: | A1UD 5986 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108 R900 00 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 5982 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3234 02 |
| Деталь: | Paperfeed Detection harness /3 |
| Парткод: | A1UD N12B 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0ED 5910 00 |
| Деталь: | TRAY |
| Парткод: | A02E 5911 00 |
| Деталь: | Bypass Tray Assy |
| Парткод: | A1UD R706 00 |
| Деталь: | Reinforce Cover |
| Парткод: | A1UD 1051 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1023 00 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06 M601 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1337 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1338 00 |
| Деталь: | GUIDE |
| Парткод: | 1164 2051 01 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A1UD 1339 00 |
| Деталь: | RUBBER FOOT |
| Парткод: | 4030 2080 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1327 00 |
| Деталь: | HOLDER |
| Парткод: | A1UD 1331 00 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A0P0 M504 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1010 01 |
| Деталь: | FNS Relay harness |
| Парткод: | A1UD N131 00 |
| Деталь: | AC Wiring /120V |
| Парткод: | A1UD N111 00 |
| Деталь: | Reinforce Cover /2 |
| Парткод: | A1UD 1062 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1312 00 |
| Деталь: | BRACKET |
| Парткод: | 4037 2239 02 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1311 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1UD 1341 01 |
| Деталь: | AC Wiring /230V |
| Парткод: | A1UD N112 00 |
| Деталь: | AC Wiring /100V |
| Парткод: | A1UD N110 00 |
| Деталь: | Power source Cord /100V |
| Парткод: | A0ED N300 01 |
| Деталь: | Power code /120V |
| Парткод: | A1UD N300 00 |
| Деталь: | Ground Plate spring |
| Парткод: | A1UD 1330 00 |
| Деталь: | DC Brushless motor |
| Парткод: | A1UD M100 00 |
| Деталь: | SHAFT |
| Парткод: | 4030 2524 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 2523 03 |
| Деталь: | GEAR 18T |
| Парткод: | 4030 2518 01 |
| Деталь: | Gear 21T |
| Парткод: | 4030 2517 01 |
| Деталь: | BRACKET |
| Парткод: | 4030 2525 01 |
| Деталь: | GEAR 24T |
| Парткод: | 4030 2516 01 |
| Деталь: | GEAR 28/49T |
| Парткод: | 4030 2515 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4030 2530 02 |
| Деталь: | GEAR 58/67T |
| Парткод: | 4030 2505 01 |
| Деталь: | GEAR 23/60T |
| Парткод: | 4030 2506 01 |
| Деталь: | GEAR 19/44T |
| Парткод: | 4030 2512 01 |
| Деталь: | SPRING |
| Парткод: | 4030 2531 04 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | GEAR 42T |
| Парткод: | 4030 2511 01 |
| Деталь: | GEAR 49T |
| Парткод: | 4030 2510 01 |
| Деталь: | GEAR 32/35T |
| Парткод: | 4030 2526 01 |
| Деталь: | GEAR 29T |
| Парткод: | 4040 2545 01 |
| Деталь: | GEAR 27T |
| Парткод: | 4030 2535 01 |
| Деталь: | BRACKET ASSY |
| Парткод: | 4030 R712 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 2116 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 2206 00 |
| Деталь: | GEAR 26T |
| Парткод: | 4040 2552 01 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A1UD R700 00 |
| Деталь: | Conveyance Drive harness /1 |
| Парткод: | A1UD N12N 01 |
| Деталь: | ADU Drive Caulking Assy |
| Парткод: | A1UD R7A1 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A1UD 8121 00 |
| Деталь: | Stepping motor |
| Парткод: | A1UD M101 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 8117 00 |
| Деталь: | FLANGE |
| Парткод: | A1UD 8139 00 |
| Деталь: | TIMING BELT |
| Парткод: | A1UD 8138 00 |
| Деталь: | TIMING BELT |
| Парткод: | A1UD 8113 00 |
| Деталь: | FLANGE |
| Парткод: | A02E 8119 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 8132 00 |
| Деталь: | GEAR |
| Парткод: | A1UD 8136 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A1UD 7115 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A1UD 7126 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A1UD 7117 00 |
| Деталь: | ROLL |
| Парткод: | 4030 3122 01 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A1UD 7116 00 |
| Деталь: | SHAFT |
| Парткод: | 4030 3121 01 |
| Деталь: | Timing Belt 264L |
| Парткод: | A02E 8113 00 |
Коды ошибок
C0001
C0202
C0204
C0206
C0208
C0209
C0210
C0211
C0212
C0213
C0214
C0215
C1004
C1081
C1113
C1114
C1115
C1116
C1150
C1156
C1158
C1181
C1182
C1183
C1190
C1191
C1194
C11A1
C11A2
C11A7
C11B0
C11B2
C11B5
C11C0
C11E0
C11E1
C11E2
C1301
C1402
C2201
C2253
C2254
C2350
C2557
C2558
C255C
C2564
C2650
C3421
C3423
C3721
C3723
C3821
C3823
C4101
C4501
C5102
C5103
C5351
C5356
C5370
C5501
C5601
C5602
C6102
C6103
C6704
C6751
C6752
C6901
C6902
C6903
C6F01
C8101
C8107
C8302
C9401
C9402
CA051
CA052
CA053
CC001
CC151
CC152
CC153
D-1
L-10
L-11
L-4
L-6
L-7
L-8
L-9
P-27
S-1
Описание
| Error code: | C0001 |
| Description: | Main Motor turning at abnormal timing The Main Motor Lock signal remains faulty for a predetermined continuous period of time while the Main Motor remains stationary. |
| Remedy: | 1 Main Motor rotation while it is being energized: the voltage across PJ13I-7A on Master Board and GND remains DC 0 V. YES: Change Master Board. NO: Change motor. |
| Error code: | C0202 |
| Description: | Magenta PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 1 upper limit sensor (PS6) • Tray 1 lift-up motor (M6) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0204 |
| Description: | Yellow PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 2 upper limit sensor (PS14) • Tray 2 lift-up motor (M8) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0206 |
| Description: | Black PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 3 upper limit sensor (PS22) • Tray 3 lift-up motor (M23) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0208 |
| Description: | Tray 5 feeder up/down abnormality |
| Causes: | • Tray 4 upper limit sensor (PS27) • Tray 4 lift-up motor (M24) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Error code: | C0209 |
| Description: | LCT elevator motor malfunction |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0211 |
| Description: | Tray 1 feeder up/down abnormality • The paper feed tray 1 lift-up position sensor is not unblocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The paper feed tray 1 lift-up position sensor is not blocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started. |
| Causes: | • Bypass lift-up motor (M26) • Bypass upper limit sensor (PS35) • Bypass lower limit sensor (PS36) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check the connector of M1 for proper drive coupling and correct as necessary. 3 PS17 I/O check PRCB CN6PRCB-7 (ON) D-2. 4 SL1 operation check PRCB CN6PRCB-4 (ON) D-1. 5 M1 operation check PRCB CN34PRCB-10 (REM) PRCB CN34PRCB-13 (LOCK) D-22. 6 Change SL1. 7 Change M1. 8 Change PRCB. |
| Error code: | C0212 |
| Description: | LCT ejection failure |
| Error code: | C0213 |
| Description: | LCT shift gate malfunction |
| Error code: | C0214 |
| Description: | LCT shifting failure |
| Causes: | • Shifter motor (M133) • Shifter stop / lower limit position sensor (PS138) • Shifter home sensor (PS139) • PC control board (PCCB) |
| Error code: | C0215 |
| Description: | LCT shift motor malfunction |
| Error code: | C1004 |
| Description: | FNS communication error |
| Causes: | FS control board (FSCB) |
| Error code: | C1081 |
| Description: | SD communication error <When FS-534+SD-511 is installed> When a communication error is detected between the FS control board (FSCB) and the SD control board (SDDB). |
| Causes: | • SD drive board (SDDB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace SDDB. 4 Replace FSCB. |
| Error code: | C1113 |
| Description: | Stopper drive motor`s malfunction. <When FS-536SD or FS-537SD is installed> The stopper home sensor (PS6) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stopper drive motor (M4) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Stopper drive motor (M4) • Stopper home sensor (PS6) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M4-SDCB J10 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-SDCB J10 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: SDCB J10-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 2-P 5. M4 operation check • Control signal: SDCB J10-6 to 9 • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 1-P 6. Replace M4. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1114 |
| Description: | Alignment motor’s malfunction. <When FS-536SD or FS-537SD is installed> The alignment home sensor (PS4) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the alignment motor (M3) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Alignment motor (M3) • Alignment home sensor (PS4) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M3-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS4-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS4 I/O check, sensor check • Control signal: SDCB J7-6 (ON) • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 5. M3 operation check • Control signal: SDCB J7-7 to 10 • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 6. Replace M3. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1115 |
| Description: | Center fold knife motor`s malfunction. <When FS-536SD or FS-537SD is installed> The center fold knife home sensor (PS8) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Center fold knife motor (M9) • Center fold knife home sensor (PS8) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M9-SDCB J11 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS8-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS8 I/O check, sensor check • Control signal: SDCB J7-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-P, FS-537/FS-537SD 6-P 5. M9 operation check • Control signal: SDCB J11-11 to 20 • Location of electrical component: FS-536/FS-536SD 2-L, FS-537/FS-537SD 1-K 6. Replace M9. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1116 |
| Description: | Center-staple transfer motor malfunction <When FS-526+SD-508 is installed> • The transport motor (M33) does not reach the specified speed even after the set period of time has elapsed after it starts to operate. <When FS-527+SD-509 is installed> • The center fold roller motor (M25) does not reach the specified speed even after the set period of time has elapsed after it starts to operate. |
| Causes: | When FS-526+SD-508 is installed: Transport motor (M33) SD drive board (SDDB) FS control board (FSCB). When FS-527+SD-509 is installed: Center fold roller motor (M25) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | When FS-526+SD-508 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M33 for proper drive coupling, and correct as necessary. - - 3 M33 operation check SDDB CN409-1 to 11 SD-508 K-5 4 Change M33 - - 5 SDDB ICP5 conduction check - - 6 Change SDDB - - 7 Change FSCB. When FS-527+SD-509 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M25 for proper drive coupling, and correct as necessary. - - 3 M25 operation check SDDB PJ4-1 to 11 SD-509 B-3 4 Change M25 - - 5 Change SDDB - - 6 Change FSCB |
| Error code: | C1150 |
| Description: | Side feeder lift motor going down error (optional side feeder) • Lower limit detection switch does not turn off within 15 s of the side feeder lift motor starting (within 200 ms during paper feeding). This error is detected four times successively. |
| Causes: | Poor contact of lower limit detection switch connector terminals. Defective side feeder main PWB. Defective side feeder lift motor. |
| Remedy: | Poor contact of lower limit detection switch connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective side feeder main PWB. Replace the side feeder main PWB. Defective side feeder lift motor. Run maintenance mode U247 and measure the voltage between terminals YC5-A12 (side-feeder main circuit board) and YC6- B11. (Make sure all of LUSSW, UCSSW, LLSSW and RCSSW are off.) Despite either DC24V or DC-24V is observed but if the side-feeder lift motor does not operate, replace the side-feeder lift motor. |
| Error code: | C1156 |
| Description: | SD paddle motor malfunction. <When FS-536SD or FS-537SD is installed> The paddle home sensor (PS5) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the SD paddle motor (M7) is turning. |
| Causes: | <When FS-536SD or FS-537SD is installed> • SD paddle motor (M7) • Paddle home sensor (PS5) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M7-SDCB J8 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS5-SDCB J8 for proper connection and correct as necessary. 4. PS5 I/O check, sensor check • Control signal: SDCB J8-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 5. M7 operation check • Control signal: SDCB J8-4 to 7 • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 6. Replace M7. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1158 |
| Description: | Center-staple paddle roller motor malfunction (leading edge) <When FS-527+SD-509 is installed>• Even after the set period of time has elapsed after the lower paddle motor (M22) starts running, a change of motor lock signal is not detected and neither the paper detection sensor/1 (PS43) nor the paper detection sensor/2 (PS44) is turned ON. |
| Causes: | lower paddle motor (M22) Paper detection sensor/1 (PS43) Paper detection sensor/2 (PS44) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M22 for proper drive coupling, and correct as necessary. - - 3 PS43 I/O check, sensor check SDDB PJ9-8 (ON) SD-509 G-1 4 PS44 I/O check, sensor check SDDB PJ13-2 (ON) SD-509 G-3 5 M22 operation check SDDB PJ5-1 to 5 SD-509 B-4 6 Change M22 - - 7 Change SDDB - - 8 Change FSCB |
| Error code: | C1181 |
| Description: | Paddle motor malfunctions |
| Error code: | C1182 |
| Description: | Unsupported option trouble |
| Causes: | When JS-504 is installed: Shift motor (M2) Shift home sensor (PS6) JS control board (JSCB). When FS-527 is installed: Tray2 shift motor (M16) Tray2 shift home sensor (PS25) FS control board (FSCB) |
| Error code: | C1183 |
| Description: | Finishing option elevator drive malfunction |
| Causes: | Elevate motor (M15) Tray1 lower position sensor (PS21) Tray1 upper position sensor (PS24) Tray1 upper position switch (SW2) Tray1 lower position switch (SW3) FS control board (FSCB) |
| Error code: | C1190 |
| Description: | Finishing option aligning bar moving mechanism malfunction 1 |
| Causes: | Alignment plate motor (M13) Alignment plate home sensor (PS17) FS control board (FSCB) |
| Error code: | C1191 |
| Description: | Finishing option aligning bar moving mechanism malfunction 2 |
| Error code: | C1194 |
| Description: | Leading edge stopper motor drive malfunction <When FS-527 is installed> • The leading edge stopper home sensor (PS20) is turned neither ON nor OFF even after the set period of time has elapsed after the leading edge stopper motor (M14) is turned ON. |
| Causes: | Leading edge stopper motor (M14) Leading edge stopper home sensor (PS20) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M13 for proper drive coupling, and correct as necessary. - - 3 PS17 I/O check, sensor check FSCB PJ17-6 (ON) FS-527 B to C-8 4 M13 operation check FSCB PJ8-9 to 12 FS-527 B to C-6 5 Change M13 - - 6 Change FSCB |
| Error code: | C11A1 |
| Description: | Finishing option exit roller pressure/retraction failure |
| Causes: | Exit roller retraction motor (M9) Exit roller pressure sensor (PS12) FS control board (FSCB) |
| Error code: | C11A2 |
| Description: | Saddle exit roller pressure/retraction failure |
| Causes: | <When FS-536 or FS-536SD is installed> • Receiving roller retraction motor (M4) • Receiving roller retraction sensor (PS11) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Receiving roller retraction motor (M10) • Receiving roller retraction sensor (PS22) • FS control board (FSCB) |
| Error code: | C11A7 |
| Description: | Tray 3 exit roller pressure/ retraction malfunction <When JS-603 is installed> • The exit roller pressure sensor (PS12) is turned neither ON nor OFF even after the set period of time has elapsed after the exit roller retraction motor (M9) is turned ON. |
| Causes: | Tray3 exit roller retraction motor (M17) Tray3 exit roller retraction sensor (PS35) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M17 for proper drive coupling, and correct as necessary. - - 3 PS35 I/O check, sensor check FSCB PJ12-6 (ON) FS-527 (JS-603) L-10 4 M17 operation check FSCB PJ30-2 (REM) FS-527 (JS-603) L-9 5 Change M17 - - 6 Change FSCB |
| Error code: | C11B0 |
| Description: | Finishing option stapler unit CD drive failure |
| Causes: | Stapler movement motor (M11) Stapler home sensor/1 (PS18) Stapler home sensor/2 (PS19) FS control board (FSCB) |
| Error code: | C11B2 |
| Description: | Finishing option stapling mechanism malfunction 1 |
| Causes: | Stapler unit FS control board (FSCB) |
| Error code: | C11B5 |
| Description: | Side staple 1 drive failure |
| Causes: | Saddle stapler unit SD drive board (SDDB) FS control board (FSCB) |
| Error code: | C11C0 |
| Description: | Punch motor malfunction |
| Causes: | Punch motor/1 (M100) Punch home sensor/1 (PS100) FS control board (FSCB) |
| Error code: | C11E0 |
| Description: | Unsupported option trouble |
| Causes: | When FS-527 is installed: Duplex path switching motor (M2) Duplex path switching sensor (PS3)FS control board (FSCB). When JS-504 is installed: Route change motor (M3) Route change home sensor (PS4) JS control board (JSCB) |
| Error code: | C11E1 |
| Description: | Paper exit switching drive malfunction. <When FS-536 or FS-536SD is installed> The exchange folded paper output sensor (PS30) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the FNS entry transport motor (M2) is turned ON. <When FS-537 or FS-537SD is installed> The route change gate home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the route change gate motor (M4) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS entry transport motor (M2) • Exchange folded paper output sensor (PS30) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Route change gate motor (M4) • Route change gate home sensor (PS21) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M2-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS30-FSCB J4 for proper connection and correct as necessary. 4. PS30 I/O check, sensor check • Control signal: FSCB J4<A>-15 (ON) • Location of electrical component: FS-536/FS-536SD 14-C 5. M2 operation check • Control signal: FSCB J9<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 12-C 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M4-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-FSCB J12 for proper connection and correct as necessary. 4. PS21 I/O check, sensor check • Control signal: FSCB J12<B>-12 (ON) • Location of electrical component: FS-537/FS-537SD 18-D 5. M4 operation check • Control signal: FSCB J21<B>-8 to 9 • Location of electrical component: FS-537/FS-537SD 18-D 6. Replace M4. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C11E2 |
| Description: | Paper exit switching (JS) drive malfunction. <When FS-537 or FS-537SD is installed> The sub tray/JS route change gate home sensor (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the sub tray discharge motor (M18) is turned ON. |
| Causes: | • Sub tray discharge motor (M18) • Sub tray/JS route change gate home sensor (PS23) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M18-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M18 for proper drive coupling and correct as necessary. 3. Check the connector between PS23-FSCB J12 for proper connection and correct as necessary. 4. PS23 I/O check, sensor check • Control signal: FSCB J12<A>-16 (ON) • Location of electrical component: FS-537/FS-537SD 17-D 5. M18 operation check • Control signal: FSCB J12<A>-5 to 6 • Location of electrical component: FS-537/FS-537SD 16-D 6. Replace M18. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1301 |
| Description: | Finishing option cooling fan motor failure |
| Error code: | C1402 |
| Description: | IR illegal interrupt vector occurred |
| Causes: | FS control board (FSCB) |
| Remedy: | 1. Reset the malfunction. 2. If the same malfunction persists, change the Image Processing Board. |
| Error code: | C2201 |
| Description: | Drum motor steady-state error |
| Causes: | The ready signal is at the H level for 1s continuously after the drum motor became stable. |
| Remedy: | 1 Checking the drum motor The drum motor drive is faulty. Execute U030 [Process] and check the drum motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 4 Checking the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 5 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2253 |
| Description: | Color PC motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/YMC (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2254 |
| Description: | Color PC motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/YMC motor (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2350 |
| Description: | Toner suction fan failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Toner suction fan (FM7) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM7-relay CN326-MFPB CN24E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM7 operation check • Control signal: MFPB CN24E-7 (DRIVE), MFPB CN24E-9 (LOCK) • Location of electrical component: 1-K 4. Replace FM7. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C2557 |
| Description: | Abnormally low toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Developing unit • Toner cartridge • Toner empty sensor/K (PZS/K) • Toner supply motor/K (M12) • Toner cartridge motor/CK (M14) • MFP board (MFPB) |
| Remedy: | 1 M3 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 D-23. 2 Reinstall imaging unit. 3 Reinstall toner cartridge. 4 Change imaging unit /K. 5 Change PRCB. |
| Error code: | C2558 |
| Description: | Abnormally high toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Developing unit • Toner cartridge • Sub hopper unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit /K. 4 Change PRCB. |
| Error code: | C255C |
| Description: | Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit /K. 2 Change imaging unit /K. 3 Change PRCB. |
| Error code: | C2564 |
| Description: | Black TCR sensor failure. • The TCR sensor input is 0. • This detection is used for detecting disconnection of TCR sensor connector. |
| Causes: | • Developing unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Check the connector between the developing unit-relay CN214-PHRYB CN6 for proper connection and correct as necessary. 3. Replace the developing unit. 4. PHRYB PS1 conduction check. 5. Replace PHRYB. 6. Replace MFPB |
| Error code: | C2650 |
| Description: | PF feed motor error (Side Multi Feeder) Object: Side multi feeder |
| Causes: | The ready signal is not at the L level (stable rotation) for passing 2s since the PF feed motor drive is started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected. The drive parts are faulty. Execute U247 [SMT] > [Motor On] to check the paper feeding operation. If the PF feed motor does not properly operate, reconnect the connector. Check if the PF feed roller and the drive gears rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. Executing U247 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF main PWB • PF main PWB - Engine PWB (Cable from the side multi feeder) Wiring diagram 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF drive unit (Side multi feeder) 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 5 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3421 |
| Description: | Fusing heaters trouble (heating side) • The temperature detected by the heating roller thermistor/C does not reach a predetermined level after the lapse of a predetermined period of time after the heating roller fusing heater lamp lights up. • The difference between the maximum and minimum temperatures detected by the heating roller thermistor/C within a predetermined period of time after the start of a warm-up cycle is below or above a predetermined value. • The temperature detected after a pressure level correction remains under a predetermined level even after the lapse of a predetermined period of time after the start of the temperature detection. • During a warm-up, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. |
| Causes: | • Fusing unit • C3421: Fusing temperature sensor/1 (TEM1: center) • C3426: Fusing temperature sensor/1 (TEM1: edge) • DC power supply (DCPS) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3423 |
| Description: | Fusing heaters trouble (pressurizing side) • After warm-up operation starts, the fusing pressure roller thermistor does not detect a temperature as high as a predetermined one though a predetermined period of time has elapsed. • The temperature of the pressure roller remains lower than a predetermined level even after the lapse of a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3721 |
| Description: | Fusing abnormally high temperature detection (heating side) • The heating roller thermistor continues to detect a temperature higher than a predetermined one for a predetermined period of time. • Hard protection signal L is detected continuously over a predetermined period of time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3723 |
| Description: | Fusing abnormally high temperature detection (pressurizing side) • The temperature of the pressure roller continues to be higher than a predetermined level for a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • Pressure roller power supply unit (PRPU) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3821 |
| Description: | Fusing abnormally low temperature detection (heating side) • The heating roller thermistor continues to detect a temperature lower than a predetermined one for a predetermined period of time. • In the states other than a warm-up operation, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. • The power supply frequency cannot be detected. |
| Causes: | • Fusing unit • C3821: Thermistor/1 (TH1) • C3822: Thermistor/2 (TH2) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3823 |
| Description: | Fusing abnormally low temperature detection (pressurizing side) • The temperature of the pressure roller continues to be lower than a predetermined level for a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • Pressure roller power supply unit (PRPU) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C4101 |
| Description: | BD initialization error |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4501 |
| Description: | Laser malfunction. • SOS signal is not detected even after the lapse of a given period of time after starting the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Causes: | • PH unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between the PH unit-PHRYB CN8 for proper connection and correct as necessary. 2. Replace the PH unit. 3. PHRYB IC5 conduction check. 4. Replace PHRYB. 5. Replace MFPB. |
| Error code: | C5102 |
| Description: | Main high-voltage error C |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5103 |
| Description: | Main high-voltage error M |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5351 |
| Description: | Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • DC power supply cooling fan (FM9) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1 Check the FM5 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check PRCB CN30PRCB-11 (ON) PRCB CN30PRCB-12 (LOCK) K-8. 4 Change FM5. 5 Change DCPU. 6 Change PRCB. |
| Error code: | C5356 |
| Description: | Cooling fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | Cooling fan motor (FM3) Printer control board (PRCB) |
| Remedy: | 1 Check the FM3 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM3 operation check PRCB CN15-4 (REM) PRCB CN15-6 (LOCK) K-7 to 8 4 Change FM3 - - 5 PRCB ICP6 conduction check - - 6 Change MFPB |
| Error code: | C5370 |
| Description: | Rear side cooling fan’s failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan remains stationary. |
| Causes: | • MFP control board cooling fan (FM17) • MFP board (MFPB) |
| Remedy: | 1 Check the connector between FM3-MFPB PJ26 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM3 operation check MFPB PJ26 (LOCK) 7-P. 4 Replace FM3. 5 Replace MFPB. |
| Error code: | C5501 |
| Description: | AC signal abnormality The zero cross signal is not input during fusing phase control. |
| Causes: | • Fusing unit • DC power supply (DCPU) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU and PRCB for proper connection and correct or change as necessary. 3 Replace fusing unit. 4 Replace PRCB. 5 Replace DCPU. |
| Error code: | C5601 |
| Description: | Engine control malfunction. Engine control malfunction is detected with port monitor control. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the connectors on MFPB for proper connection and correct as necessary. 2. Rewrite the firmware. 3. Replace MFPB. |
| Error code: | C5602 |
| Description: | FPGA configuration error • When a configuration check is performed on the extended IC chip (FPGA) located on the printer control board (PRCB), error is detected. |
| Remedy: | 1 Reboot the machine. 2 Rewrite the firmware. 3 Change PRCB. |
| Error code: | C6102 |
| Description: | Drive system home sensor malfunction • The scanner home sensor (PS201) is unable to detect the scanner located at its home position. • The scanner home sensor (PS201) is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor (PS201) detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor (PS201). |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6103 |
| Description: | Slider over running The scanner home sensor (PS201) detects the scanner at its home position during a period of time that begins with the time when a prescan command and a scan preparation command are executed and ends when a home return command is executed. |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6704 |
| Description: | Image input time out. Image data is not input from the scanner to the MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Memory Bus Check] -> [Scanner -> Memory], and conduct the memory bus function. 2. Correct the harness connection between scanner section and MFPB if faulty. 3. MFPB F3E conduction check 4. Replace MFPB. 5. Replace the CCD unit. |
| Error code: | C6751 |
| Description: | CCD gain adjustment failure. • The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment. |
| Causes: | • LED exposure unit • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 2. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 3. Correct the harness connection between SCDB CN1-DCPU CN005 if faulty. 4. Check for possible extraneous light and correct as necessary. 5. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 6. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 7. Replace SCDB 8. Replace the CCD unit. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | C6752 |
| Description: | ASIC clock input error (front side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on CCD board (CCDB) was conducted, and verification failure was detected. |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Correct the harness connection of CCDB if faulty. 2. Replace the CCD unit. 3. MFPB F3E conduction check 4. Replace MFPB. |
| Error code: | C6901 |
| Description: | DSC board mount failure 1 When MFP detects that DSC board/1 (front side) is not properly installed. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6902 |
| Description: | DSC board bus check NG1-1 When DSC bus check (front side) detects an error. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6903 |
| Description: | DSC board bus check NG1-2 When DSC bus check (front side) detects an error. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6F01 |
| Description: | Scanner sequence trouble 1. The original transport interval becomes shorter than the predetermined value due to an original transport control error in original reading in DF. |
| Causes: | • MFP board (MFPB) • DF control board (DFCB) |
| Remedy: | 1. Correct the harness connection between main body and DF if faulty. 2. Replace DFCB. 3. Replace MFPB. |
| Error code: | C8101 |
| Description: | Before reading pressure welding alienation mechanism trouble. • During a pressure motion being performed, the before read sensor (PS6) output does not change from H to L. • During a retraction motion being performed, the before read sensor (PS6) output does not change from L to H. |
| Causes: | • Reading roller pressure/retraction motor (M6) • Before read sensor (PS6) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M6-relay CN118-DFCB CN4 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-relay CN120-DFCB CN11 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: DFCB CN11-2 (ON) • Location of electrical component: DF 1-C 5. M6 operation check • Control signal: DFCB CN4-1 to 2 • Location of electrical component: DF 10-C 6. Replace M6. 7. DFCB ICP9 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8107 |
| Description: | Glass cleaning mechanism trouble. The front side cleaning home sensor (PS18) is not turned ON (unblocked) even after the set period of time has elapsed after the front side cleaning motor (M8) turned ON. |
| Causes: | • Front side cleaning motor (M8) • Front side cleaning home sensor (PS18) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M8-DFCB CN14 for proper connection and correct as necessary. 2. Check the connector between PS18-DFCB CN18 for proper connection and correct as necessary. 3. Check the connector of M8 for proper drive coupling and correct as necessary. 4. PS18 I/O check, sensor check • Control signal: DFCB CN18-3 (ON) • Location of electrical component: DF 3-C 5. M8 operation check • Control signal: DFCB CN14-1 to 4 • Location of electrical component: DF 6-C 6. Replace M8. 7. DFCB ICP8 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8302 |
| Description: | Cooling fan motor`s failure. The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Cooling fan motor (FM) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between FM-relay CN115-DFCB CN19 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM operation check • Control signal: DFCB CN19-3 (LOCK) • Location of electrical component: DF 4-C 4. Replace FM. 5. DFCB ICP10 conduction check. 6. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C9401 |
| Description: | Exposure LED lighting failure The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | C9402 |
| Description: | Exposure LED lighting abnormally The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | CA051 |
| Description: | Standard controller configuration failure • The controller of the printer control board (PRCB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA052 |
| Description: | Controller hardware error • A controller hardware error is detected in the network I/F. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA053 |
| Description: | Controller start failure • A controller start failure is detected in the controller interface. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CC001 |
| Description: | Vendor connection failure |
| Causes: | • Printer control board (PRCB) • Coin vendor (Japan) • Coin vendor kit (North America, Europe) |
| Error code: | CC151 |
| Description: | ROM contents error upon startup (MSC) • A fault is detected in a sequence of ROM contents check of the MSC (PRCB) during starting |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. |
| Error code: | CC152 |
| Description: | ROM contents error upon startup (scanner). A fault is detected in a sequence of ROM contents check of the MFPB during starting |
| Remedy: | 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace the appropriate board. |
| Error code: | CC153 |
| Description: | ROM contents error upon startup (PRT) • A fault is detected in a sequence of ROM contents check of the mechanical control board (MFPB) during starting. |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. |
| Error code: | D-1 |
| Description: | Split line detect (front side). • While recovering from the power save mode or when the main power switch and power key are ON, it detects whether or not stain exist at the original reading glass when the DF is closed. This warning will be displayed if the original is set to DF when stain exist. • The thin line detection level and the warning display can be changed by [Service Mode] -> [System 2] -> [ADF Scan Glass Contamin. Set.] -> [Front Side]. |
| Causes: | • Front side cleaning motor (M8) • Front side cleaning home sensor (PS18) • DF control board (DFCB) |
| Remedy: | 1. Wipe clean the glass surface of the original reading glass. 2. Check the front side glass cleaning roller unit for proper installation and correct if necessary. Clean the front side glass cleaning roller unit if dirty. 3. Select [Service Mode] -> [System 2] ->[ADF Scan Glass Contamin. Set.] -> [Front Side], and change the setting. 4. Check the DFCB connector for proper connection and correct as necessary. 5. M8 operation check 6. Replace the front side glass cleaning roller unit. 7. Replace DFCB. |
| Error code: | L-10 |
| Description: | Warning of transfer roller unit’s excess number of prints - The transfer roller unit’s count of sheets printed, which is used to judge the life of the transfer roller unit, exceeds the excess warning threshold. - Printing with this warning being displayed is not included in the image warranty. |
| Error code: | L-11 |
| Description: | Fusing unit rotation time excess warning - The count of hours the fusing unit has been rotated (main motor rotation time), which is used to judge the life of the fusing unit, exceeds the excess warning threshold. - Printing with this warning being displayed is not included in the image warranty. |
| Error code: | L-4 |
| Description: | Drum unit rotation time excess warning - PC drum rotation time count value used for the life judgment of drum unit (the value for PC drum rotation distance calculated into the rotation time) is above the threshold value for the excess warning. - Printing with this warning being displayed is not included in the image warranty. |
| Error code: | L-6 |
| Description: | Warning of excess hours of developer use - The count of hours the developer has been used (PC motor rotation time), which is used to judge the life of the developer, exceeds the excess warning threshold. - Printing with this warning being displayed is not included in the image warranty. |
| Error code: | L-7 |
| Description: | Warning of ozone filter’s excess number of prints - The ozone filter’s count of sheets printed, which is used to judge the life of the ozone filter, exceeds the excess warning threshold. - Printing with this warning being displayed is not included in the image warranty. |
| Error code: | L-8 |
| Description: | Paper dust remover excess warning - The paper dust remover’s count (PC motor rotation time), which is used to judge the life of the paper dust remover, exceeds the excess warning threshold. - Printing with this warning being displayed is not included in the image warranty. |
| Error code: | L-9 |
| Description: | Developing unit rotation time excess warning - The count of hours the developing unit has been rotated (PC motor rotation time), which is used to judge the life of the developing unit, exceeds the excess warning threshold. - Printing with this warning being displayed is not included in the image warranty. |
| Error code: | P-27 |
| Description: | Secondary transfer ATVC failure. An abnormal average value is detected during an adjustment of the second transfer ATVC value. |
| Causes: | • High voltage unit/2 (HV2) • MFP board (MFPB) • Image transfer entrance guide • 2nd transfer assy • Transfer belt unit |
| Remedy: | 1. Check the contact between the roller opposed to the 2nd transfer roller in the transfer belt unit and the grounding terminal. Clean the joint or correct if necessary. 2. Check the image transfer entrance guide for proper installation and correct if necessary. 3. Check that the spring does not come off during the pressure operation of the transfer roller and correct if necessary. 4. Check the contact at the joint of the 2nd transfer assy and HV2. Clean the joint or correct if necessary. 5. Replace the transfer belt unit. 6. Replace HV2. 7. MFPB F12E conduction check 8. Replace MFPB. |
| Error code: | S-1 |
| Description: | CCD gain adjustment failure. It is detected that the CCD clamp gain adjustment value is faulty. |
| Causes: | • LED exposure unit (LU201) • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB and MFPB if faulty. 2. Check for possible extraneous light and correct as necessary. 3. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 4. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 5. Replace the CCD unit. 6. Replace SCDB. 7. Replace MFPB. |
