Konica-Minolta bizhub C10

Рейтинг

Модули

RIGHT FRAME 2

ELECTRICAL COMPONENTS

PAPER TAKE-UP SECTION 3

VERTICAL TRANSPORT SECTION

MAIN FRAME

DRIVE SECTION 3

ADF 3

PH Section

TRANSFER SECTION

ADF 2

FUSING UNIT

LEFT FRAME

Duplex Unit

PAPER TAKE-UP SECTION

EXTERNAL PARTS

DRIVE SECTION

DUPLEX UNIT 2

RIGHT FRAME

LEFT FRAME 3

ADF

TOP COVER 2

PAPER TAKE-UP SECTION 2

DRIVE SECTION 4

TRANSFER ROLLER SECTION

DUPLEX UNIT 3

TOP COVER

IR SECTION

IR SECTION 2

DRIVE SECTION 2

MAIN FRAME 2

LEFT FRAME 2

Детали DRIVE SECTION 4

Деталь:	GEAR 24T
Парткод:	4139 2602 01

Деталь:	TENSION SPRING
Парткод:	4131 2621 01

Деталь:	BALL BEARING
Парткод:	4131 2607 01

Деталь:	LEVER
Парткод:	4139 2604 01

Деталь:	GEAR 35T
Парткод:	4139 2606 01

Деталь:	GEAR 20/35T
Парткод:	A00V 2607 00

Деталь:	GEAR 35T
Парткод:	A00V 2402 00

Деталь:	Stepping motor
Парткод:	A00V M101 00

Деталь:	MOTOR
Парткод:	9314 1400 11

Деталь:	GEAR 19/48T
Парткод:	4139 2622 01

Деталь:	SHAFT
Парткод:	4139 2603 02

Деталь:	BRACKET ASSY
Парткод:	A00V R717 00

Деталь:	BRACKET ASSY
Парткод:	4139 0201 02

Коды ошибок

04H

05H

08H

0BH

0CH

0FH

101H

102H

10H

12H

14H

15H

16H

17H

18H

19H

1AH

1BH

21H

23H

24H

29H, 2AH. 2BH, 2CH

2DH

31H

F0H

Описание

Парткод

Название

Konica Minolta TN212Y Тонер-картридж желтый

Konica Minolta TN212M Тонер-картридж пурпурный

Konica Minolta TN212C Тонер-картридж голубой

Konica Minolta TN212K Тонер-картридж черный

Konica Minolta Барабан-картридж

Деталь:	REGULATING PLATE ASSY
Парткод:	4139 R706 00

Деталь:	LABEL CONSUMABLES REODER
Парткод:	4139 7334 01

Деталь:	Push Button Switch ASSY
Парткод:	4139 R735 00

Деталь:	HUMIDITY CONVERTION EL.
Парткод:	9372 5400 11

Деталь:	LABEL COPY PROHIBITION
Парткод:	4556 9405 00

Error code:	04H
Description:	Printer control board malfunction • Communications with the M/C expansion IO G/A (IC on the printer control board) are not properly carried out.
Causes:	• CR Encoder failure (contaminated/detached scale, Encoder Board failure) • CR Motor failure • Carriage overload error (paper jam/foreign object) • Cable disconnection
Remedy:	1 Check the PRCB connector for proper connection and correct as necessary. 2 Change PRCB.

Error code:	05H
Description:	Flash ROM malfunction • Engine firmware upgrading has failed.
Causes:	• ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • ADF Motor failure • Paper jam • Cable disconnection
Remedy:	1 Check the PRCB connector for proper connection and correct as necessary. 2 Change PRCB.

Error code:	08H
Description:	Main motor malfunction • The motor lock signal remains HIGH for a predetermined consecutive period of time while the main motor remains energized. • The motor lock signal remains LOW for a predetermined consecutive period of time while the main motor remains deenergized.
Causes:	• CR Encoder failure (contaminated/detached scale, Encoder Board failure) • Tooth skip of the CR Timing Belt • Improper tension of the CR Timing Belt • Paper jam
Remedy:	1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M1 operation check. PRCB PJ8PRCB-5 (REM) PRCB PJ8PRCB-8 (LOCK) C-4. 5 Change PRCB. 6 Change DCPU1.

Error code:	0BH
Description:	Ventilation fan motor malfunction • The fan motor lock signal remains HIGH for a predetermined consecutive period of time while the ventilation fan motor remains energized.
Causes:	• ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • ADF Motor failure • ADF drive overload (paper jam/foreign object) • Cable disconnection
Remedy:	1 Check the FM2 connector for proper connection and correct as necessary. 2 Check FM2 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 FM2 operation check. PRCB PJ10PRCB-1 (REM) PECB PJ10PRCB-3 (LOCK) C-4. 5 Change PRCB. 6 Change DCPU1.

Error code:	0CH
Description:	Power supply cooling fan motor malfunction • The fan motor lock signal remains HIGH for a predetermined consecutive period of time while the power supply cooling fan motor remains energized.
Causes:	An error occurred in the CR motor operating sequence
Remedy:	1 Check the FM1 connector for proper connection and correct as necessary. 2 Check FM1 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M1 operation check. PRCB PJ4PRCB-1 (REM) PRCB PJ4PRCB-3 (LOCK) C-2. 5 Change PRCB. 6 Change DCPU1.

Деталь:	FRICTION SHEET
Парткод:	4136 3049 01

Деталь:	POWER SUPPLY
Парткод:	4139 6210 05

Деталь:	POWER SUPPLY
Парткод:	4139 6211 05

Деталь:	SWITCH
Парткод:	9332 1710 41

Error code:	0FH
Description:	Duplex cooling fan motor malfunction

Error code:	10H
Description:	Polygon motor malfunction • A low motor lock signal is not detected even after the lapse of a predetermined period of time after the polygon motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the polygon motor remains energized.
Causes:	• CIS Unit failure • Scanner Housing failure • Main Board failure
Remedy:	1 Check the cable and connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PRCB.

Error code:	12H
Description:	Laser malfunction • The SOS signal is not detected within a predetermined period of time after the output of a laser has been started. • The SOS signal is never detected in the image area.
Causes:	• Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Pickup Motor driver failure (Main Board failure)
Remedy:	1 Check the cable and connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PRCB.

Error code:	14H
Description:	2nd image transfer pressure /retraction failure • The state of the retraction position sensor/2nd image transfer is not changed from the unblocked to blocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/2nd image transfer is in the unblocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/2nd image transfer is not blocked (roller in the retracted position) within a predetermined period of time after the retraction sequence of the 2nd transfer roller has been started. • The retraction position sensor/2nd image transfer is not unblocked (roller in the pressed position) within a predetermined period of time after the pressure sequence of the 2nd transfer roller has been started.
Causes:	• Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Pickup Motor failure • Pickup drive mechanism (2nd cassette) overload (paper jam/foreign object) • Cable disconnection
Remedy:	1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the SD4 connector for proper connection and correct as necessary. 4 Check the PRCB connector for proper connection and correct as necessary. 5 PS5 sensor check. PRCB PJ14PRCB-3 (ON) J to K-3. 6 SD4 operation check. PRCB PJ11PRCB-2 (REM) J to K-1. 7 M1 operation check. PRCB PJ8PRCB-5 (REM) PRCB PJ8PRCB-8 (LOCK) C-4. 8 Change PRCB.

Error code:	15H
Description:	Cleaning blade pressure /retraction failure • The state of the retraction position sensor/cleaning blade is not changed from the blocked to unblocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/cleaning blade is in the blocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/cleaning blade is not unblocked (blade in the retracted position) within a predetermined period of time after the retraction sequence of the cleaning blade has been started. • The retraction position sensor/cleaning blade is not blocked (blade in the pressed position) within a predetermined period of time after the pressure sequence of the cleaning blade has been started.
Remedy:	1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the SD3 connector for proper connection and correct as necessary. 4 Check the PRCB connector for proper connection and correct as necessary. 5 PS6 sensor check. PRCB PJ9PRCB-11 (ON) C-5. 6 SD3 operation check. PRCB PJ10PRCB-5 (REM) C-3. 7 M1 operation check. PRCB PJ8PRCB-5 (REM) PRCB PJ8PRCB-8 (LOCK) C-4. 8 Change PRCB.

Error code:	16H
Description:	Transfer belt rotation failure • The belt positioning sensor does not detect the transfer belt position detection hole a second time even after the lapse of a predetermined period of time after it has detected one while the transfer belt is rotated.
Causes:	• Pickup drive mechanism (2nd cassette) overload (paper jam/foreign object)
Remedy:	1 Check the PRCB connector for proper connection and correct as necessary. 2 PS4 sensor check. PRCB PJ9PRCB-8 (ON) C-5. 3 Change transfer belt unit. 4 Change PRCB.

Error code:	17H
Description:	Rack rotation failure • The rack positioning sensor is in the blocked state when the rack motor remains deenergized. • The rack positioning sensor is not blocked a second time even after the lapse of a predetermined period of time after it has been blocked once while the rack motor remains energized. • The rack positioning sensor is unable to detect the deceleration control position after the lapse of a given period of time after the rack motor has started while the rack motor is turning. • The count value of the edge of ON signal of the rack positioning sensor during each developing positions are not a predetermined value while the rack motor is turning.
Remedy:	1 Check the M2 connector for proper connection and correct as necessary. 2 Check M2 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 PS3 sensor check. PRCB PJ5PRCB-11 (ON) C-6 5 M2 operation check. PRCB PJ5PRCB-1 to 4 (Pulse Output) C-6 to 7. 6 Change PRCB.

Error code:	18H
Description:	Heating roller warm-up failure • The thermistor does not detect a predetermined temperature value even after the lapse of a predetermined period of time after the current warm-up cycle has been started and the current warm-up cycle is thus not completed.
Causes:	• Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Paper jam
Remedy:	1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU1, and PRCB for proper connection and correct as necessary. 3 Check the lever of the safety switch and correct as necessary. 4 Change the fusing unit. 5 Change PRCB. 6 Change DCPU1.

Error code:	19H
Description:	Abnormally low heating roller temperature • The temperature detected by the thermistor remains lower than a predetermined value for a predetermined period of time.
Causes:	• Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Motor driver failure (Main Board failure)
Remedy:	1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU1, and PRCB for proper connection and correct as necessary. 3 Check the lever of the safety switch and correct as necessary. 4 Change the fusing unit. 5 Change PRCB. 6 Change DCPU1.

Error code:	1AH
Description:	Abnormally high heating roller temperature • The temperature detected by the thermistor is a predetermined value or higher for a predetermined period of time.
Causes:	• Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Pickup Motor failure • Pickup drive mechanism (2nd cassette) overload (paper jam/foreign object) • Cable disconnection
Remedy:	1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, DCPU1, and PRCB for proper connection and correct as necessary. 3 Check the lever of the safety switch and correct as necessary. 4 Change the fusing unit. 5 Change PRCB. 6 Change DCPU1.