Konica-Minolta bizhub C3850
Рейтинг
Модули
PRINTER CONTROL BOARD SECTION
EXTERNAL PARTS 2
ELECTRICAL COMPONENTS
ELECTRICAL COMPONENTS 2
CASSETTE SECTION 2
TRANSFER BELT UNIT
PRINT HEAD SECTION
VERTICAL CONVEYANCE SECTION 2
TRANSFER BELT UNIT 3
Vertical conveyance Section
DUP RIVERSE DRIVE SECTION
TONER BOTTLE DRIVE SECTION
TRANSFER BELT UNIT 2
CASSETTE SECTION
ADF, IR SECTION
MAIN DRIVE SECTION
VERTICAL CONVEYANCE SECTION 3
EXTERNAL PARTS
FUSING SECTION
PAPER FEED DRIVE SECTION
TRANSFER GUIDE SECTION
Детали PRINTER CONTROL BOARD SECTION
| Деталь: | Reinforce Plate /Upper |
| Парткод: | A3GN109500 |
| Деталь: | SEAL |
| Парткод: | A3GN146000 |
| Деталь: | Shield Sheet |
| Парткод: | A3GN146200 |
| Деталь: | Reinforce Frame |
| Парткод: | A3GN109800 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | HOLDER |
| Парткод: | A3GN135300 |
| Деталь: | Adjusting Spring |
| Парткод: | A0VD135201 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A3GN135200 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06M60100 |
| Деталь: | Interlock Wiring |
| Парткод: | A3GNN10D00 |
| Деталь: | Seal /Left |
| Парткод: | A3GN146400 |
| Деталь: | Hold Holder |
| Парткод: | A0VD136100 |
| Деталь: | Connecting Seal /Rear |
| Парткод: | A3GN144100 |
| Деталь: | Connecting Seal |
| Парткод: | A3GN144500 |
| Деталь: | COVER |
| Парткод: | A3GN145700 |
| Деталь: | Holding Seal |
| Парткод: | A3GN144602 |
| Деталь: | Filter Holder |
| Парткод: | A3GN144402 |
| Деталь: | Main body Wiring /B |
| Парткод: | A3GNN10200 |
| Деталь: | Main body Wiring |
| Парткод: | A4Y4N10200 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | Supply Duct /Left rear |
| Парткод: | A3GN142101 |
| Деталь: | Transmitting Wiring |
| Парткод: | A3GNN10T00 |
| Деталь: | Polygon Relay harness |
| Парткод: | A3GNN10900 |
| Деталь: | Mounting Screw |
| Парткод: | A3GN134700 |
| Деталь: | Main body Wiring /R |
| Парткод: | A3GNN10100 |
| Деталь: | PWB Assembly(PRCB) |
| Парткод: | A3GNH00104 |
| Деталь: | HOLDER |
| Парткод: | A3GN133500 |
| Деталь: | FERRITECORE |
| Парткод: | A5C1M92100 |
| Деталь: | SPACER |
| Парткод: | A3GN135100 |
| Деталь: | COVER MAIN BODY |
| Парткод: | A3GN162800 |
| Деталь: | COVER MAIN BODY |
| Парткод: | A3GN162701 |
| Деталь: | PLATE NUT |
| Парткод: | 4002504202 |
| Деталь: | Cover /Rear |
| Парткод: | A3GN160602 |
| Деталь: | Support Part /Right |
| Парткод: | A3GN160900 |
| Деталь: | Lock Plate spring |
| Парткод: | A3GN621701 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN109300 |
| Деталь: | Cover /Right |
| Парткод: | A3GN162300 |
| Деталь: | Cover /Right |
| Парткод: | A3GN162000 |
| Деталь: | HOLDER |
| Парткод: | A3GN133600 |
| Деталь: | HIGH VOLTAGE UNIT |
| Парткод: | A3GNM40300 |
| Деталь: | PCB Support |
| Парткод: | V502010044 |
| Деталь: | I/F Flat cable |
| Парткод: | A3GNN10N00 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | FERRITE CORE |
| Парткод: | A3GNM93200 |
| Деталь: | HOLD PLATE |
| Парткод: | A3GN145800 |
| Деталь: | FERRITE CORE |
| Парткод: | A3GNM71C00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN134100 |
| Деталь: | HOLDER |
| Парткод: | A3GN133700 |
| Деталь: | Label Toner |
| Парткод: | A3GN401200 |
| Деталь: | GUIDE |
| Парткод: | A3GN133800 |
| Деталь: | Cover /Left front |
| Парткод: | A3GN133102 |
| Деталь: | Cover /Left front |
| Парткод: | A3GN138100 |
| Деталь: | AC Wiring |
| Парткод: | A3GNN10C00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN132200 |
| Деталь: | SEESAW-SWITCH |
| Парткод: | 4038M60000 |
| Деталь: | FERRITECORE |
| Парткод: | A3EWM90300 |
| Деталь: | AC Wiring |
| Парткод: | A3GNN10B00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN134600 |
| Деталь: | SHIELD PLATE |
| Парткод: | A3GN132600 |
| Деталь: | Insulating sheet |
| Парткод: | A3GN134400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN133400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN132300 |
| Деталь: | Lock Plate spring |
| Парткод: | A3GN621701 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | FERRITE CORE |
| Парткод: | A3GNM93100 |
| Деталь: | Supply Duct /Left rear |
| Парткод: | A3GN142200 |
| Деталь: | SHIELD PLATE |
| Парткод: | A3GN134500 |
| Деталь: | SEAL |
| Парткод: | A3GN132900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN132400 |
| Деталь: | PROTECTION |
| Парткод: | 1154467001 |
| Деталь: | RUBBER FOOT |
| Парткод: | 996305501 |
| Деталь: | Relay harness |
| Парткод: | A3GNN12200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN130000 |
| Деталь: | PCB Support |
| Парткод: | V502010045 |
| Деталь: | SUPPORT |
| Парткод: | V502010026 |
| Деталь: | DC Power source (100-127V) |
| Парткод: | A3GNM40000 |
| Деталь: | DC Power source (220-240V) |
| Парткод: | A3GNM40100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A121132200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN132801 |
| Деталь: | Support Rubber |
| Парткод: | A121132600 |
| Деталь: | Relay harness |
| Парткод: | A3GNN12500 |
| Деталь: | Relay harness |
| Парткод: | A0VDN12300 |
| Деталь: | HDD |
| Парткод: | A3GNM71B00 |
| Деталь: | PWB Assembly |
| Парткод: | A3GNH01006 |
| Деталь: | Power Supply Wiring |
| Парткод: | A3GNN10E00 |
| Деталь: | SPACER |
| Парткод: | V502010029 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN132501 |
| Деталь: | I/F Flat cable |
| Парткод: | A3GNN10M00 |
| Деталь: | FERRITECORE |
| Парткод: | A5C1M92100 |
| Деталь: | PROTECTION |
| Парткод: | 1154467001 |
| Деталь: | FAX Assembly (WW-100V) |
| Парткод: | A6EDH01905 |
| Деталь: | FAX Assembly (JP) |
| Парткод: | A6EDH01A05 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN132700 |
| Деталь: | Protection Cover |
| Парткод: | A3GN134300 |
| Деталь: | Relay harness |
| Парткод: | A6EDN12300 |
| Деталь: | Relay harness |
| Парткод: | A6EDN12400 |
| Деталь: | REGULATING PLATE |
| Парткод: | A3GN626401 |
| Деталь: | CUSHION |
| Парткод: | A0VD624300 |
| Деталь: | SEAL |
| Парткод: | A3GN626900 |
| Деталь: | REGULATING PLATE |
| Парткод: | A3GN626301 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A3GN626800 |
| Деталь: | LOCK LEVER |
| Парткод: | A3GN626600 |
| Деталь: | HOLDER |
| Парткод: | A3GN626700 |
| Деталь: | LOCK CLAW |
| Парткод: | A3GN626500 |
| Деталь: | RACK |
| Парткод: | A3GN626100 |
| Деталь: | Label Prohibition inkjet media |
| Парткод: | 4138731601 |
| Деталь: | LABEL |
| Парткод: | A3GN940201 |
| Деталь: | Paper feed Cover /Upper |
| Парткод: | A3GN628200 |
| Деталь: | Paper feed Cover /Front |
| Парткод: | A3GN628100 |
| Деталь: | Adjusting Plate |
| Парткод: | A3GN627100 |
| Деталь: | REGULATING PLATE |
| Парткод: | A3GN627200 |
| Деталь: | PLATE SPRING |
| Парткод: | A3GN627300 |
| Деталь: | SHEET |
| Парткод: | A3GN627400 |
| Деталь: | Ground Plate spring /B |
| Парткод: | A3GN621300 |
| Деталь: | Ground Plate spring /A |
| Парткод: | A3GN621200 |
| Деталь: | FIXED LEAD RESISTORS |
| Парткод: | V800400032 |
| Деталь: | RACK |
| Парткод: | A3GN626200 |
| Деталь: | GEAR 14T |
| Парткод: | 4658301201 |
| Деталь: | Label Paper supply |
| Парткод: | A3GN940101 |
| Деталь: | SPACER |
| Парткод: | 4004305201 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN110900 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Dust-proof Filter |
| Парткод: | A0P0158100 |
| Деталь: | TRANSFER UNIT |
| Парткод: | A4Y5WY2 |
| Деталь: | CONTACT |
| Парткод: | A0VD136800 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A3GN110401 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD114101 |
| Деталь: | SEAL |
| Парткод: | A3GN111800 |
| Деталь: | GROUND SPRING |
| Парткод: | A3GN110600 |
| Деталь: | SEAL |
| Парткод: | A0VD363700 |
| Деталь: | SHUTTER |
| Парткод: | A0VD362300 |
| Деталь: | Holding Lever |
| Парткод: | A3GN110700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A3GN110800 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A3GN110501 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD214700 |
| Деталь: | RAIL /FRONT |
| Парткод: | A3GN110001 |
| Деталь: | RAIL /REAR |
| Парткод: | A3GN110101 |
| Деталь: | SEAL |
| Парткод: | A3GN113300 |
| Деталь: | SEAL |
| Парткод: | A0VD362400 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD362500 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | A6X0R70000 |
| Деталь: | RUBBER FOOT |
| Парткод: | 996305501 |
| Деталь: | GUIDE |
| Парткод: | A3GN102500 |
| Деталь: | STOPPER |
| Парткод: | A3GN621600 |
| Деталь: | Gear 16/26T |
| Парткод: | A0VD235600 |
| Деталь: | GEAR 16T |
| Парткод: | A0VD235400 |
| Деталь: | GEAR 16/16T |
| Парткод: | A0VD235500 |
| Деталь: | Gear 22/30T |
| Парткод: | A0VD235900 |
| Деталь: | Holding Plate |
| Парткод: | A3GN235200 |
| Деталь: | Waste Toner Bottle |
| Парткод: | A4Y5WY1 |
| Деталь: | Drive Holder |
| Парткод: | A3GN235101 |
| Деталь: | HOLDER |
| Парткод: | A3GN106700 |
| Деталь: | COVER |
| Парткод: | A3GN107100 |
| Деталь: | LEVER |
| Парткод: | A3GN362601 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD362702 |
| Деталь: | GEAR 16T |
| Парткод: | A0VD235700 |
| Деталь: | Regulating Sheet |
| Парткод: | A3GN102300 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140051 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD164000 |
| Деталь: | COVER |
| Парткод: | A3GN812400 |
| Деталь: | SHAFT |
| Парткод: | A0VD162101 |
| Деталь: | Lever /Rear |
| Парткод: | A0VD163400 |
| Деталь: | GUIDE |
| Парткод: | A0VD161600 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A3GN813900 |
| Деталь: | HOLDER |
| Парткод: | A0VD161100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD163500 |
| Деталь: | Lever /Front |
| Парткод: | A3GN813600 |
| Деталь: | Wiring Cover |
| Парткод: | A0VD162400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD163200 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | GROUND PLATE |
| Парткод: | A3GN702800 |
| Деталь: | Conveyance ASSY |
| Парткод: | A3GNR70700 |
| Деталь: | FIXED LEAD RESISTORS |
| Парткод: | V800400032 |
| Деталь: | GROUND PLATE |
| Парткод: | A0VD702600 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD703700 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0VD702700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD701300 |
| Деталь: | Neutralizing Part |
| Парткод: | A0VD701600 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD700302 |
| Деталь: | ACTUATOR |
| Парткод: | A0VD700202 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A3GN700500 |
| Деталь: | CONTACT |
| Парткод: | A3GN701100 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A3GN708101 |
| Деталь: | HOLDER |
| Парткод: | A3GN700100 |
| Деталь: | 2nd Transfer Roller Unit |
| Парткод: | A4Y5WY3 |
| Деталь: | DUCT |
| Парткод: | A3GN813201 |
| Деталь: | COVER |
| Парткод: | A3GN816000 |
| Деталь: | SEAL |
| Парткод: | A3GN816700 |
| Деталь: | SEAL |
| Парткод: | A3GN816800 |
| Деталь: | HOLDER |
| Парткод: | A3GN816300 |
| Деталь: | COVER |
| Парткод: | A3GN817100 |
| Деталь: | SCREW |
| Парткод: | 4163529301 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | CONNECTOR |
| Парткод: | V651010002 |
| Деталь: | FILTER |
| Парткод: | A3GN816600 |
| Деталь: | Filter Holder |
| Парткод: | A3GN817400 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN817500 |
| Деталь: | Connecting Seal /Middle |
| Парткод: | A3GN144200 |
| Деталь: | SEALING PART |
| Парткод: | A3GN140600 |
| Деталь: | Supply Duct /Rear |
| Парткод: | A3GN148200 |
| Деталь: | Sealing Part Outside |
| Парткод: | A3GN149600 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148700 |
| Деталь: | Supply Duct /Rear |
| Парткод: | A3GN148100 |
| Деталь: | Supply Duct /Rear |
| Парткод: | A3GN148001 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148300 |
| Деталь: | SEALING PART |
| Парткод: | A3GN141201 |
| Деталь: | Supply Duct /Rear |
| Парткод: | A3GN140100 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145100 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145200 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145600 |
| Деталь: | Sealing Part /Middle |
| Парткод: | A3GN140700 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145400 |
| Деталь: | Sealing Part /Lower |
| Парткод: | A3GN149100 |
| Деталь: | Sealing Part /Lower |
| Парткод: | A3GN149200 |
| Деталь: | SEALING PART |
| Парткод: | A3GN145300 |
| Деталь: | Supply Duct /Lower |
| Парткод: | A3GN140300 |
| Деталь: | SEALING PART |
| Парткод: | A3GN141100 |
| Деталь: | SEALING PART |
| Парткод: | A3GN141300 |
| Деталь: | SEALING PART |
| Парткод: | A3GN140800 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148500 |
| Деталь: | Sealing Part Outside |
| Парткод: | A3GN149300 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148800 |
| Деталь: | Sealing Part /Side |
| Парткод: | A3GN148900 |
| Деталь: | Sealing Part Outside |
| Парткод: | A3GN149500 |
| Деталь: | Mounting Duct /Rear |
| Парткод: | A3GN147201 |
| Деталь: | FAN MOTOR |
| Парткод: | 4139M10000 |
| Деталь: | Sealing Part /Lower |
| Парткод: | A3GN149000 |
| Деталь: | SEAL |
| Парткод: | A3GN147600 |
| Деталь: | GUIDE |
| Парткод: | A3GN147000 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0VD563201 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0VD563101 |
| Деталь: | LABEL |
| Парткод: | A3GN940300 |
| Деталь: | Label Prohibition inkjet media |
| Парткод: | 4138731601 |
| Деталь: | TRAY |
| Парткод: | A0VD561700 |
| Деталь: | LIFTING PLATE |
| Парткод: | A00F565101 |
| Деталь: | COLLAR |
| Парткод: | 4120301901 |
| Деталь: | LEVER |
| Парткод: | 4138320501 |
| Деталь: | Bypass Tray |
| Парткод: | A0VD560202 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4138325301 |
| Деталь: | Manual Bypass ASSY |
| Парткод: | A3GNR70900 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A3GN590700 |
| Деталь: | GEAR 14T |
| Парткод: | 4131302702 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4138325501 |
| Деталь: | FRAME |
| Парткод: | A0VD560402 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD561301 |
| Деталь: | BUSHING |
| Парткод: | 4138324401 |
| Деталь: | Paper feed Frame |
| Парткод: | A3GN590101 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD560601 |
| Деталь: | ACTUATOR |
| Парткод: | A0VD560300 |
| Деталь: | GUIDE |
| Парткод: | A0VD561800 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4131305601 |
| Деталь: | SHAFT |
| Парткод: | A0VD560801 |
| Деталь: | ROLLER |
| Парткод: | 4138303202 |
| Деталь: | CLUTCH |
| Парткод: | 4030303401 |
| Деталь: | MANUAL PAPER FEED ASSY |
| Парткод: | A3GNR70600 |
| Деталь: | GROUND PLATE |
| Парткод: | A0VD560900 |
| Деталь: | STOPPER |
| Парткод: | 4138323602 |
| Деталь: | PLATE SPRING |
| Парткод: | 4138323701 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD624800 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4658015106 |
| Деталь: | HOLDER |
| Парткод: | A0VD621100 |
| Деталь: | GUIDE |
| Парткод: | A3GN590501 |
| Деталь: | GUIDE |
| Парткод: | A0VD561502 |
| Деталь: | Open/close Cover |
| Парткод: | A3GN810101 |
| Деталь: | Open/close Stopper |
| Парткод: | A3GN812300 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313130051 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN817000 |
| Деталь: | Drive Holder /B |
| Парткод: | A3GN822200 |
| Деталь: | Gear 36/37T |
| Парткод: | A0VD822600 |
| Деталь: | Gear 23T |
| Парткод: | A0VD822800 |
| Деталь: | GEAR 19T |
| Парткод: | A0VD822700 |
| Деталь: | BUSHING |
| Парткод: | A00F813000 |
| Деталь: | ROLL |
| Парткод: | A00F813100 |
| Деталь: | Torque limiter ASSY |
| Парткод: | A3GN823500 |
| Деталь: | SHAFT |
| Парткод: | A3GN822901 |
| Деталь: | GEAR 18T |
| Парткод: | A0VD822400 |
| Деталь: | Drive Holder /A |
| Парткод: | A3GN822100 |
| Деталь: | DUCT |
| Парткод: | A0VD814100 |
| Деталь: | Guide /Upper |
| Парткод: | A3GN820401 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD820700 |
| Деталь: | Neutralizing Brush |
| Парткод: | A3GN825100 |
| Деталь: | GUIDE |
| Парткод: | A3GN825600 |
| Деталь: | ROLL |
| Парткод: | A0VD820200 |
| Деталь: | Guide /Lower |
| Парткод: | A3GN820200 |
| Деталь: | CONTACT |
| Парткод: | A0VD820900 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A121820800 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD820300 |
| Деталь: | DUCT |
| Парткод: | A0VD814000 |
| Деталь: | Reverse/exit Roller |
| Парткод: | A3GN820100 |
| Деталь: | GEAR 14T |
| Парткод: | A0VD821100 |
| Деталь: | CLUTCH |
| Парткод: | A2YFM20000 |
| Деталь: | Drive Side plate |
| Парткод: | A0VD822300 |
| Деталь: | GEAR 24T |
| Парткод: | A0VD822500 |
| Деталь: | CLUTCH |
| Парткод: | A0VD823300 |
| Деталь: | DUP Reverse Drive Assy |
| Парткод: | A3GNR70300 |
| Деталь: | Relay Wiring |
| Парткод: | A3GNN10400 |
| Деталь: | Stepping motor |
| Парткод: | A5C1M10400 |
| Деталь: | HOLDER |
| Парткод: | A3GN400100 |
| Деталь: | GEAR 25T |
| Парткод: | A3GN400400 |
| Деталь: | Gear 49/86T |
| Парткод: | A3GN400300 |
| Деталь: | Gear 20/107T |
| Парткод: | A3GN400200 |
| Деталь: | GEAR 30T |
| Парткод: | A02E240600 |
| Деталь: | SPRING |
| Парткод: | 4038541101 |
| Деталь: | GUIDE |
| Парткод: | A3GN400800 |
| Деталь: | SPRING |
| Парткод: | A3GN401100 |
| Деталь: | WASHER |
| Парткод: | 4131412801 |
| Деталь: | TB Drive Assy |
| Парткод: | A3GNR70200 |
| Деталь: | HOLDER |
| Парткод: | A3GN400002 |
| Деталь: | HOLDER |
| Парткод: | A3GN402001 |
| Деталь: | HOLDER |
| Парткод: | A3GN402101 |
| Деталь: | HOLDER |
| Парткод: | A3GN402200 |
| Деталь: | LABEL |
| Парткод: | A2X0949100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN400900 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A3GN401000 |
| Деталь: | Relay Connector |
| Парткод: | A0EDM60001 |
| Деталь: | Toner Detection harness |
| Парткод: | A3GNN10700 |
| Деталь: | LABEL K |
| Парткод: | A3GN401600 |
| Деталь: | LABEL C |
| Парткод: | A3GN401500 |
| Деталь: | LABEL M |
| Парткод: | A3GN401400 |
| Деталь: | LABEL Y |
| Парткод: | A3GN401300 |
| Деталь: | Relay Wiring |
| Парткод: | A3GNN10U00 |
| Деталь: | GUIDE |
| Парткод: | A3GN137100 |
| Деталь: | Transfer Wiring |
| Парткод: | A3GNN10Q00 |
| Деталь: | Toner Drive harness |
| Парткод: | A3GNN10800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN112900 |
| Деталь: | Main body Wiring |
| Парткод: | A3GNN10000 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A3GN112800 |
| Деталь: | HOLDER |
| Парткод: | A3GN113000 |
| Деталь: | Rail /Lower |
| Парткод: | A3GN111001 |
| Деталь: | Rail /Upper |
| Парткод: | A3GN111300 |
| Деталь: | Rail /Lower |
| Парткод: | A3GN111200 |
| Деталь: | COVER |
| Парткод: | A3GN112400 |
| Деталь: | SEAL |
| Парткод: | A3GN113200 |
| Деталь: | SEAL |
| Парткод: | A3GN113100 |
| Деталь: | Rail /Lower |
| Парткод: | A3GN111101 |
| Деталь: | Neutralizing LED array |
| Парткод: | A3GNM30400 |
| Деталь: | Rail /Upper |
| Парткод: | A3GN111400 |
| Деталь: | LIFTING PLATE |
| Парткод: | A3GN624102 |
| Деталь: | FRICTION SHEET |
| Парткод: | 978381101 |
| Деталь: | LIFTING PLATE |
| Парткод: | A3GN624502 |
| Деталь: | SHAFT |
| Парткод: | A3GN624600 |
| Деталь: | BUSHING |
| Парткод: | 4138324401 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | CLUTCH |
| Парткод: | 4030303401 |
| Деталь: | ROLLER |
| Парткод: | 4138303202 |
| Деталь: | LOCK LEVER |
| Парткод: | A3GN625000 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1164306201 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A3GN632600 |
| Деталь: | LEVER |
| Парткод: | A3GN632501 |
| Деталь: | REGULATING PLATE |
| Парткод: | A3GN632400 |
| Деталь: | SHAFT |
| Парткод: | A3GN632200 |
| Деталь: | LEVER |
| Парткод: | A3GN632301 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A3GN632100 |
| Деталь: | WASHER |
| Парткод: | A00J192900 |
| Деталь: | Connecting Plate |
| Парткод: | A3GN631901 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN631102 |
| Деталь: | Holding Plate |
| Парткод: | A3GN631301 |
| Деталь: | LEVER |
| Парткод: | A3GN631400 |
| Деталь: | GUIDE |
| Парткод: | A3GN631500 |
| Деталь: | LEVER |
| Парткод: | A3GN631702 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A3GN631800 |
| Деталь: | GUIDE |
| Парткод: | A3GN623100 |
| Деталь: | GUIDE |
| Парткод: | 4131305702 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A3GN624400 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4131305601 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD624800 |
| Деталь: | HOLDER |
| Парткод: | A0VD621100 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4658015106 |
| Деталь: | GUIDE |
| Парткод: | A3GN624201 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN631200 |
| Деталь: | CASSETTE ASSY |
| Парткод: | A3GNR70500 |
| Деталь: | CONVEYANCE UNIT |
| Парткод: | A3GN270100 |
| Деталь: | UPPER COVER/REAR |
| Парткод: | A3GNPP0000 |
| Деталь: | CABLE CLAMP |
| Парткод: | A121PP0200 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | A121PP0100 |
| Деталь: | TRAY ASSY |
| Парткод: | A121PP0400 |
| Деталь: | OPTICAL UNIT |
| Парткод: | A3GN260100 |
| Деталь: | HINGE R |
| Парткод: | A121PP0600 |
| Деталь: | LABEL |
| Парткод: | A121944600 |
| Деталь: | Label Prohibit |
| Парткод: | A121944700 |
| Деталь: | LABEL |
| Парткод: | A161940602 |
| Деталь: | HINGE L |
| Парткод: | A121PP0500 |
| Деталь: | Separator Roller Assy |
| Парткод: | A3GNPP0100 |
| Деталь: | SOLENOID |
| Парткод: | A121PP0B00 |
| Деталь: | PHOTO SENSOR |
| Парткод: | A121PP0900 |
| Деталь: | CLUTCH |
| Парткод: | A121PP0A00 |
| Деталь: | PHOTO SENSOR |
| Парткод: | A121PP0800 |
| Деталь: | MOTOR ASSY |
| Парткод: | A121PP0E00 |
| Деталь: | SOLENOID |
| Парткод: | A121PP0C00 |
| Деталь: | PWB Assembly |
| Парткод: | A121PP0700 |
| Деталь: | Separator Pad Assy |
| Парткод: | A0CRPP0200 |
| Деталь: | PAD |
| Парткод: | A121PP0D00 |
| Деталь: | Stopper Right |
| Парткод: | A121PP0G00 |
| Деталь: | Stopper Left |
| Парткод: | A121PP0H00 |
| Деталь: | COVER |
| Парткод: | A3GN210800 |
| Деталь: | brushless Motor /20 |
| Парткод: | A161M10200 |
| Деталь: | Fusing Panel |
| Парткод: | A3GN223000 |
| Деталь: | Drive Gear 68T |
| Парткод: | A3GN220200 |
| Деталь: | BEARING |
| Парткод: | A00F213900 |
| Деталь: | Fusing Panel |
| Парткод: | A3GN223302 |
| Деталь: | Gear 21T |
| Парткод: | A0VD218301 |
| Деталь: | PIN |
| Парткод: | 4036301401 |
| Деталь: | SHAFT |
| Парткод: | A3GN223400 |
| Деталь: | GEAR 60T |
| Парткод: | A3GN212501 |
| Деталь: | GEAR 16T |
| Парткод: | A3GN212401 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD219800 |
| Деталь: | CONTACT |
| Парткод: | A3GN130700 |
| Деталь: | Bias Contact |
| Парткод: | A3GN130600 |
| Деталь: | HOLDER |
| Парткод: | A3GN131200 |
| Деталь: | SHAFT |
| Парткод: | A0VD133300 |
| Деталь: | Insulating sheet |
| Парткод: | A3GN136000 |
| Деталь: | HOLDER |
| Парткод: | A3GN130900 |
| Деталь: | HOLDER |
| Парткод: | A3GN131000 |
| Деталь: | HOLDER |
| Парткод: | A3GN131400 |
| Деталь: | COVER |
| Парткод: | A3GN131100 |
| Деталь: | CONTACT |
| Парткод: | A3GN131900 |
| Деталь: | CONTACT |
| Парткод: | A3GN131700 |
| Деталь: | CONTACT |
| Парткод: | A3GN131800 |
| Деталь: | CONTACT |
| Парткод: | A3GN131600 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0VD220300 |
| Деталь: | BUSHING |
| Парткод: | A0VD220201 |
| Деталь: | CONTACT |
| Парткод: | A3GN135600 |
| Деталь: | CONTACT |
| Парткод: | A3GN135700 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A3GNR70000 |
| Деталь: | HOLDER |
| Парткод: | A3GN134001 |
| Деталь: | PAPERFEED SOLENOID |
| Парткод: | A034M20000 |
| Деталь: | PROTECTION PART |
| Парткод: | A3GN708000 |
| Деталь: | brushless Motor /40 |
| Парткод: | A161M10001 |
| Деталь: | Brushless motor |
| Парткод: | A2XKM10300 |
| Деталь: | FERRITECORE |
| Парткод: | A3EWM90300 |
| Деталь: | WASHER |
| Парткод: | A02E193000 |
| Деталь: | GUIDE |
| Парткод: | A3GN813700 |
| Деталь: | DUP Conveyance Assy |
| Парткод: | A3GNR70800 |
| Деталь: | CLUTCH |
| Парткод: | A2YFM20000 |
| Деталь: | Conveyance Wiring |
| Парткод: | A3GNN10300 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD702501 |
| Деталь: | BUSHING |
| Парткод: | A3GN702300 |
| Деталь: | GEAR 16T |
| Парткод: | A0VD235301 |
| Деталь: | ROLL |
| Парткод: | 4138352802 |
| Деталь: | BUSHING |
| Парткод: | 4138353202 |
| Деталь: | ROLLER |
| Парткод: | A3GN702900 |
| Деталь: | ROLLER |
| Парткод: | A3GN702100 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0VD703700 |
| Деталь: | GEAR 15T |
| Парткод: | A0VD703001 |
| Деталь: | CLUTCH |
| Парткод: | A011M20000 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A3GN703400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD705303 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD703501 |
| Деталь: | BUSHING |
| Парткод: | A0VD702400 |
| Деталь: | Cover /Upper |
| Парткод: | A3GN160402 |
| Деталь: | HOLD PLATE |
| Парткод: | A3GN162500 |
| Деталь: | Shield Sheet |
| Парткод: | A3GN146100 |
| Деталь: | COVER |
| Парткод: | A3GN162100 |
| Деталь: | Cover /Upper |
| Парткод: | A3GN160503 |
| Деталь: | Support Part |
| Парткод: | A3GN160800 |
| Деталь: | Open/close Stopper |
| Парткод: | A3GN812300 |
| Деталь: | SHEET |
| Парткод: | A3GN941100 |
| Деталь: | Cover /Front |
| Парткод: | A3GN160200 |
| Деталь: | Cover /Front |
| Парткод: | A3GN160104 |
| Деталь: | Cleaning Part |
| Парткод: | A3GN162600 |
| Деталь: | BAND |
| Парткод: | A0ED162401 |
| Деталь: | Cover /Left |
| Парткод: | A3GN160302 |
| Деталь: | Logo Mark |
| Парткод: | A00J945500 |
| Деталь: | Label bizhub C3850 |
| Парткод: | A3GN941000 |
| Деталь: | Label bizhub C3350 |
| Парткод: | A4Y4941000 |
| Деталь: | SEAL |
| Парткод: | A3GN162900 |
| Деталь: | SEAL |
| Парткод: | A3GN163000 |
| Деталь: | Label JAM |
| Парткод: | A0VD949100 |
| Деталь: | Label Hi-Temp Caution/Jam |
| Парткод: | A3GN948300 |
| Деталь: | GUIDE |
| Парткод: | A121902500 |
| Деталь: | LEVER |
| Парткод: | A121893002 |
| Деталь: | ACTUATOR |
| Парткод: | A0VD907300 |
| Деталь: | Fusing Unit (100V) |
| Парткод: | A4Y5W01 |
| Деталь: | Fusing Unit (120V) |
| Парткод: | A4Y5W11 |
| Деталь: | Fusing Unit (220-240V) |
| Парткод: | A4Y5W21 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Paper exit Holder |
| Парткод: | A121890302 |
| Деталь: | Paper exit Holder |
| Парткод: | A3GN892300 |
| Деталь: | Paper exit Holder |
| Парткод: | A121895302 |
| Деталь: | Insulating Sheet /Front |
| Парткод: | A3GN106100 |
| Деталь: | SEAL |
| Парткод: | A3GN146300 |
| Деталь: | Fixing Relay harness |
| Парткод: | A3GNN10500 |
| Деталь: | Insulating Sheet /Rear |
| Парткод: | A3GN106200 |
| Деталь: | SPRING |
| Парткод: | A0VD890200 |
| Деталь: | ACTUATOR |
| Парткод: | A3GN891200 |
| Деталь: | Gear 38/40T |
| Парткод: | A0VD890800 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | A3GN890103 |
| Деталь: | GUIDE |
| Парткод: | A3GN892101 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD892400 |
| Деталь: | Paper exit Roll |
| Парткод: | A3GN890301 |
| Деталь: | PAPER FEED DRIVE ASSY |
| Парткод: | A3GNR70100 |
| Деталь: | Guide Sheet |
| Парткод: | A3GN217000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0VD233102 |
| Деталь: | Gear 38/65T |
| Парткод: | A0VD230400 |
| Деталь: | BUSHING |
| Парткод: | 4036473001 |
| Деталь: | PIN |
| Парткод: | 4036301401 |
| Деталь: | GEAR 36T |
| Парткод: | A0VD231101 |
| Деталь: | SHAFT |
| Парткод: | A0VD230800 |
| Деталь: | BUSHING |
| Парткод: | A0VD702400 |
| Деталь: | Gear 23/55T |
| Парткод: | A0VD230301 |
| Деталь: | GEAR 22T |
| Парткод: | A0VD231200 |
| Деталь: | GEAR 25T |
| Парткод: | A0VD230901 |
| Деталь: | GEAR 20T |
| Парткод: | A0VD233301 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | LEVER |
| Парткод: | A0VD624100 |
| Деталь: | PAWL |
| Парткод: | 4138259601 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4138259701 |
| Деталь: | Sensor Wiring |
| Парткод: | A3GNN10K00 |
| Деталь: | SHAFT |
| Парткод: | A0VD230501 |
| Деталь: | CLUTCH |
| Парткод: | A02EM20000 |
| Деталь: | BUSHING |
| Парткод: | 4134588202 |
| Деталь: | SHAFT |
| Парткод: | A0VD230101 |
| Деталь: | GUIDE |
| Парткод: | A3GN707700 |
| Деталь: | GUIDE |
| Парткод: | A3GN707600 |
| Деталь: | GUIDE |
| Парткод: | A0VD707501 |
| Деталь: | ACTUATOR |
| Парткод: | A0VD707101 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0VD707201 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A0P0M50400 |
| Деталь: | GUIDE |
| Парткод: | A0VD707303 |
| Деталь: | Transfer Relay harness |
| Парткод: | A3GNN10R00 |
| Деталь: | PROTECTION PART |
| Парткод: | A3GN708000 |
| Деталь: | PAPERFEED SOLENOID |
| Парткод: | A034M20000 |
| Деталь: | LEVER |
| Парткод: | A3GN706600 |
| Деталь: | COVER |
| Парткод: | A3GN112300 |
| Деталь: | Neutralizing LED array |
| Парткод: | A3GNM30400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A3GN111500 |
| Деталь: | HOLDER |
| Парткод: | A3GN706500 |
| Деталь: | COVER |
| Парткод: | A3GN706100 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A034213400 |
| Деталь: | CONTACT |
| Парткод: | A3GN706300 |
| Деталь: | Photo sensing |
| Парткод: | A0VDM50000 |
| Деталь: | GUIDE |
| Парткод: | A3GN706402 |
Коды ошибок
0103
0106
2152
2202
2253
2351
2411
2412
2413
2414
2551
2552
2553
2554
2555
2556
2557
2558
2559
255A
255B
255C
2561
2562
2563
2564
2650
2A21
2A22
2A23
2A24
3201
3302
3421
3426
3721
3722
3726
3821
3822
3826
3921
3922
3926
4002
4091
4092
4101
4501
4801
4802
4901
5102
5307
5351
5353
5357
5501
5601
5701
6751
6790
6791
6792
6793
9401
C151
C15C
C15D
C15E
C161
C163
C164
D004
D091
D092
D093
D094
D095
D096
D3A0, D3A2
D3F1
D3F4
D501
DC00
DC10
Описание
| Error code: | 0103 |
| Display: | MAINTENANCE CALL 0103 |
| Description: | Even though the machine carries out the regular movement, the output of Limit Sensor does not reach the expected value. |
| Causes: | Limit Sensor does not work correctly or is broken. |
| Remedy: | Limit Sensor replacement Check the mechanical backlash or loose with the scan axis related parts. |
| Error code: | 0106 |
| Description: | Machine fails to disconnect the Tool Carriage from the Head Carriage. |
| Causes: | Fault of Tool Carriage Connection Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken. |
| Remedy: | Check the mechanical Backlash or loose with the Tool Carriage part. Connection Part Replacement Limit Position Initialize |
| Error code: | 2152 |
| Description: | 1st transfer pressure/retraction malfunction • The 1st transfer pressure sensor (PS9) does not change its state from one corresponding to the retracted position to the pressed position within a predetermined period of time after the 1st transfer pressure solenoid (SD1) has been energized. • The 1st transfer pressure sensor (PS9) does not change its state from one corresponding to the pressed position to the retracted position within a predetermined period of time after the 1st transfer pressure solenoid (SD1) has been energized. |
| Causes: | • Main motor (M1) • 1st transfer pressure sensor (PS9) • 1st transfer pressure solenoid (SD1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M1-PRCB CN9 for proper connection and correct as necessary. - - 2 Check the connector of M1 for proper drive coupling and correct as necessary. - - 3 Check the connector between PS9- PRCB CN12 for proper connection and correct as necessary. - - 4 Check the connector between SD1-relay CN85-PRCB CN12 for proper connection and correct as necessary. - - 5 PS9 I/O check, sensor check PRCB CN12-3 (ON) 15-C to D 6 SD1 operation check PRCB CN12-12 (REM) 15-E 7 M1 operation check PRCB CN9-3 to 6 15-B 8 Replace M1 - - 9 PRCB F4 conduction check - - 10 Replace PRCB |
| Error code: | 2202 |
| Description: | Drum motor C steady-state error The motor revolution fluctuates more than +/-6.2% of the normal revolution for 5s continuously, after the drum motor C has stabilized. The counter achieved by timer capture is less than 2200 in 10 times in a row. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor C. Defective engine PWB. |
| Remedy: | Drum unit 1. Execute U030 Belt Meand (transfer Motor) and check that the drum motor can rotate. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the drum or the drum screw can rotate. 4. If it won’t rotate, replace the drum unit. Drum motor C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum motor C and Motor control PWB (YC4) Motor control PWB (YC3) and Engine PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum motor C. Motor control PWB Replace the Motor control PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2253 |
| Description: | Color PC motor malfunction • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. • The motor does not reach its steady rotating state even after the lapse of a predetermined period of time after it has been started. |
| Causes: | • Color PC motor (M4) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M4-PRCB CN8 for proper connection and correct as necessary. - - 2 Check the M4 connector for proper drive coupling and correct as necessary. - - 3 M4 operation check PRCB CN8-10 to 13 7-J 4 Replace M4 - - 5 PRCB F7 conduction check - - 6 Replace PRCB |
| Error code: | 2351 |
| Description: | Toner suction fan motor malfunction The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Toner suction fan motor (FM3) • Printer control board (PRCB) |
| Remedy: | 1 Check the connectors between FM3-relay CN301- PRCB CN3 for proper connection, and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM3 operation check PRCB CN3-1 (OUT) PRCB CN3-3 (LOCK) 7-K 4 Replace FM3 - - 5 PRCB F2 conduction check - - 6 Replace PRCB |
| Error code: | 2411 |
| Description: | Imaging unit/C new article release The status with the new unit is not cleared after the new imaging unit is set. |
| Causes: | • Imaging unit/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2412 |
| Description: | Imaging unit/M new article release The status with the new unit is not cleared after the new imaging unit is set. |
| Causes: | • Imaging unit/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2413 |
| Description: | Imaging unit/Y new article release The status with the new unit is not cleared after the new imaging unit is set. |
| Causes: | • Imaging unit/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2414 |
| Description: | Imaging unit/K new article release The status with the new unit is not cleared after the new imaging unit is set. |
| Causes: | • Imaging unit/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2551 |
| Description: | Abnormally low toner density detected cyan TCR sensor When sampling data is determined in TC ratio calculation control, TCR sensor output is lower than a predetermined value for a predetermined number of times in a row even though there is toner in the toner cartridge. |
| Causes: | • Imaging unit/C,M,Y,K • Toner supply motor/YM (M5) • Toner supply motor/CK (M6) • Printer control board (PRCB) |
| Remedy: | 1 Perform image troubleshooting procedure if image density is low. - - 2 Reinstall the imaging unit - - 3 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 4 M5, M6 operation check PRCB CN22-1 to 4 (M5) PRCB CN22-5 to 8 (M6) 7-I 7-K 5 Replace the imaging unit - - 6 PRCB F5 conduction check - - 7 Replace PRCB |
| Error code: | 2552 |
| Description: | Abnormally high toner density detected cyan TCR sensor TC ratio in the imaging unit, which is determined by toner replenishing amount control mechanism, is a predetermined value or more for a given number of times consecutively |
| Causes: | • Imaging unit/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2553 |
| Description: | Abnormally low toner density detected magenta TCR sensor When sampling data is determined in TC ratio calculation control, TCR sensor output is lower than a predetermined value for a predetermined number of times in a row even though there is toner in the toner cartridge. |
| Causes: | • Imaging unit/C,M,Y,K • Toner supply motor/YM (M5) • Toner supply motor/CK (M6) • Printer control board (PRCB) |
| Remedy: | 1 Perform image troubleshooting procedure if image density is low. - - 2 Reinstall the imaging unit - - 3 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 4 M5, M6 operation check PRCB CN22-1 to 4 (M5) PRCB CN22-5 to 8 (M6) 7-I 7-K 5 Replace the imaging unit - - 6 PRCB F5 conduction check - - 7 Replace PRCB |
| Error code: | 2554 |
| Description: | Abnormally high toner density detected magenta TCR sensor TC ratio in the imaging unit, which is determined by toner replenishing amount control mechanism, is a predetermined value or more for a given number of times consecutively |
| Causes: | • Imaging unit/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2555 |
| Description: | Abnormally low toner density detected yellow TCR sensor When sampling data is determined in TC ratio calculation control, TCR sensor output is lower than a predetermined value for a predetermined number of times in a row even though there is toner in the toner cartridge. |
| Causes: | • Imaging unit/C,M,Y,K • Toner supply motor/YM (M5) • Toner supply motor/CK (M6) • Printer control board (PRCB) |
| Remedy: | 1 Perform image troubleshooting procedure if image density is low. - - 2 Reinstall the imaging unit - - 3 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 4 M5, M6 operation check PRCB CN22-1 to 4 (M5) PRCB CN22-5 to 8 (M6) 7-I 7-K 5 Replace the imaging unit - - 6 PRCB F5 conduction check - - 7 Replace PRCB |
| Error code: | 2556 |
| Description: | Abnormally high toner density detected yellow TCR sensor TC ratio in the imaging unit, which is determined by toner replenishing amount control mechanism, is a predetermined value or more for a given number of times consecutively |
| Causes: | • Imaging unit/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2557 |
| Description: | Abnormally low toner density detected black TCR sensor When sampling data is determined in TC ratio calculation control, TCR sensor output is lower than a predetermined value for a predetermined number of times in a row even though there is toner in the toner cartridge. |
| Causes: | • Imaging unit/C,M,Y,K • Toner supply motor/YM (M5) • Toner supply motor/CK (M6) • Printer control board (PRCB) |
| Remedy: | 1 Perform image troubleshooting procedure if image density is low. - - 2 Reinstall the imaging unit - - 3 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 4 M5, M6 operation check PRCB CN22-1 to 4 (M5) PRCB CN22-5 to 8 (M6) 7-I 7-K 5 Replace the imaging unit - - 6 PRCB F5 conduction check - - 7 Replace PRCB |
| Error code: | 2558 |
| Description: | Abnormally high toner density detected black TCR sensor TC ratio in the imaging unit, which is determined by toner replenishing amount control mechanism, is a predetermined value or more for a given number of times consecutively |
| Causes: | • Imaging unit/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2559 |
| Description: | Cyan TCR sensor adjustment failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 255A |
| Description: | Magenta TCR sensor adjustment failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 255B |
| Description: | Yellow TCR sensor adjustment failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 255C |
| Description: | Black TCR sensor adjustment failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2561 |
| Description: | Cyan TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2562 |
| Description: | Magenta TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2563 |
| Description: | Yellow TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2564 |
| Description: | Black TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit/Y,M,C,K • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit - - 2 Check the connector between imaging unit-PRCB CN18, CN19 for proper connection and correct as necessary. - - 3 Replace the imaging unit - - 4 Replace PRCB |
| Error code: | 2650 |
| Description: | SM paper feed motor error (side multi tray) After SM paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective SM paper feed motor. Defective SM main PWB. |
| Remedy: | SM paper feed motor 1. To check the feed unit operation, execute U247 SMT- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM paper feed motor and SM main PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SM paper feed motor. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2A21 |
| Description: | Toner cartridge/C new release failure The status with the new cartridge is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between toner cartridge-relay CN79-EXCB CN4 for proper connection and correct as necessary. - - 2 Clean the connection between the toner cartridge and the machine if dirty. - - 3 Reinstall the toner cartridge 4 Check the harness for proper connection and correct as necessary. - - 5 Check the connector between EXCB CN2-PRCB CN11 for proper connection and correct as necessary. - - 6 Replace the toner cartridge - - 7 Replace PRCB |
| Error code: | 2A22 |
| Description: | Toner cartridge/M new release failure The status with the new cartridge is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between toner cartridge-relay CN79-EXCB CN4 for proper connection and correct as necessary. - - 2 Clean the connection between the toner cartridge and the machine if dirty. - - 3 Reinstall the toner cartridge 4 Check the harness for proper connection and correct as necessary. - - 5 Check the connector between EXCB CN2-PRCB CN11 for proper connection and correct as necessary. - - 6 Replace the toner cartridge - - 7 Replace PRCB |
| Error code: | 2A23 |
| Description: | Toner cartridge/Y new release failure The status with the new cartridge is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between toner cartridge-relay CN79-EXCB CN4 for proper connection and correct as necessary. - - 2 Clean the connection between the toner cartridge and the machine if dirty. - - 3 Reinstall the toner cartridge 4 Check the harness for proper connection and correct as necessary. - - 5 Check the connector between EXCB CN2-PRCB CN11 for proper connection and correct as necessary. - - 6 Replace the toner cartridge - - 7 Replace PRCB |
| Error code: | 2A24 |
| Description: | Toner cartridge/K new release failure The status with the new cartridge is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/C,M,Y,K • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between toner cartridge-relay CN79-EXCB CN4 for proper connection and correct as necessary. - - 2 Clean the connection between the toner cartridge and the machine if dirty. - - 3 Reinstall the toner cartridge 4 Check the harness for proper connection and correct as necessary. - - 5 Check the connector between EXCB CN2-PRCB CN11 for proper connection and correct as necessary. - - 6 Replace the toner cartridge - - 7 Replace PRCB |
| Error code: | 3201 |
| Description: | Fusing motor malfunction The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M2) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M2-PRCB CN9 for proper connection and correct as necessary. - - 2 Check the loading status of the fusing unit drive, and correct the error as necessary. - - 3 M2 operation check PRCB CN9-9 to 12 15-C 4 Replace M2 - - 5 PRCB F9 conduction check - - 6 Replace PRCB |
| Error code: | 3302 |
| Description: | Paper cooling fan motor malfunction The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Paper cooling fan motor (FM4) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between FM8-relay CN82-PRCB CN12 for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM4 operation check PRCB CN12-4 (OUT) PRCB CN12-6 (LOCK) 15-D 4 Replace FM4 - - 5 PRCB F2 conduction check - - 6 Replace PRCB |
| Error code: | 3421 |
| Description: | Fusing temperature increase malfunction (Main of the heating side) • Detected temperature of the fusing temperature sensor/1 (TEM1: main of the heating side) does not go up a given range of temperature even after a lapse of given period of time at warm up. • The warm-up is not completed even after the set period of time has elapsed after the warm-up is started. |
| Causes: | • Fusing unit • Fusing temperature sensor/1 (TEM1: main of the heating side) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the right door. - - 3 Check the fusing unit-PRCB CN15, DCPS CN2 for proper connection and correct as necessary. - - 4 Replace the fusing unit - - 5 Replace PRCB - - 6 Replace DCPS |
| Error code: | 3426 |
| Description: | Fusing temperature increase malfunction (Center of the heating side) • Detected temperature of the fusing temperature sensor/1 (TEM1: main of the heating side) does not go up a given range of temperature even after a lapse of given period of time at warm up. • The warm-up is not completed even after the set period of time has elapsed after the warm-up is started. |
| Causes: | • Fusing unit • Fusing temperature sensor/1 (TEM1: center of the heating side) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the right door. - - 3 Check the fusing unit-PRCB CN15, DCPS CN2 for proper connection and correct as necessary. - - 4 Replace the fusing unit - - 5 Replace PRCB - - 6 Replace DCPS |
| Error code: | 3721 |
| Description: | Fusing abnormally high temperature (Main of the heating side) Detected temperature of the fusing temperature sensor/1 (TEM1: main of the heating side) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • Fusing temperature sensor/1 (TEM1: main of the heating side) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the right door. - - 3 Check the fusing unit-PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary. - - 4 Replace the fusing unit - - 5 Replace DCPS - - 6 Replace PRCB |
| Error code: | 3722 |
| Description: | Fusing abnormally high temperature (Edge of the heating side) Detected temperature of the fusing temperature sensor/2 (TEM2) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • Fusing temperature sensor/2 (TEM2) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the right door. - - 3 Check the fusing unit-PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary. - - 4 Replace the fusing unit - - 5 Replace DCPS - - 6 Replace PRCB |
| Error code: | 3726 |
| Description: | Fusing abnormally high temperature (Center of the heating side) Detected temperature of the fusing temperature sensor/1 (TEM1: center of the heating side) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • Fusing temperature sensor/1 (TEM1: center of the heating side) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the right door. - - 3 Check the fusing unit-PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary. - - 4 Replace the fusing unit - - 5 Replace DCPS - - 6 Replace PRCB |
| Error code: | 3821 |
| Description: | Fusing abnormally low temperature (Main of the heating roller) The fusing temperature sensor/1 (TEM1: main of the heating side) continues to detect a temperature lower than a predetermined one for a predetermined period of time after warm-up is complete. |
| Causes: | • Fusing unit • Fusing temperature sensor/1 (TEM1: main of the heating side) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit -PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary. - - 4 Replace the fusing unit - - 5 Replace DCPS - - 6 Replace PRCB |
| Error code: | 3822 |
| Description: | Fusing abnormally low temperature (Edge of the heating roller) The fusing temperature sensor/2 (TEM2) continues to detect a temperature lower than a predetermined one for a predetermined period of time after warm-up is complete. |
| Causes: | • Fusing unit • Fusing temperature sensor/2 (TEM2) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit -PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary. - - 4 Replace the fusing unit - - 5 Replace DCPS - - 6 Replace PRCB |
| Error code: | 3826 |
| Description: | Fusing abnormally low temperature (Center of the heating roller) The fusing temperature sensor/1 (TEM1: center of the heating side) continues to detect a temperature lower than a predetermined one for a predetermined period of time after warm-up is complete. |
| Causes: | • Fusing unit • Fusing temperature sensor/1 (TEM1: center of the heating side) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit -PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary. - - 4 Replace the fusing unit - - 5 Replace DCPS - - 6 Replace PRCB |
| Error code: | 3921 |
| Description: | Fusing sensor wire breaks abnormality (Center of the heating roller) After a predetermined period of time after the warm-up stage is started, the fusing temperature sensor/1 (TEM1: main of the heating side) voltage does not increase by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • Fusing temperature sensor/1 (TEM1: main of the heating side) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit-PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary. - - 4 Replace the fusing unit - - 5 Replace DCPS - - 6 Replace PRCB |
| Error code: | 3922 |
| Description: | Fusing sensor wire breaks abnormality (Edge of the heating roller) After a predetermined period of time after the warm-up stage is started, the fusing temperature sensor/2 (TEM2) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • Fusing temperature sensor/2 (TEM2) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit-PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary. - - 4 Replace the fusing unit - - 5 Replace DCPS - - 6 Replace PRCB |
| Error code: | 3926 |
| Description: | Fusing sensor wire breaks abnormality (Middle of the heating roller) After a predetermined period of time after the warm-up stage is started, the fusing temperature sensor/1 (TEM1: center of the heating side) voltage does not decrease by predetermined steps (temperature rise) within a predetermined time. |
| Causes: | • Fusing unit • Fusing temperature sensor/1 (TEM1: center of the heating side) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit-PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary. - - 4 Replace the fusing unit - - 5 Replace DCPS - - 6 Replace PRCB |
| Error code: | 4002 |
| Display: | Drum End Soon:Y |
| Description: | Polygon motor C synchronization error After polygon motor C is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor C. Defective engine PWB. |
| Remedy: | Polygon motor C (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor C and LSU relay PWB (YC9) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4091 |
| Description: | Engine communication error • The engine resends the maximum number of retries (five times) after a retry sequence has occurred. • Communication with the CTL is interrupted for one min. or longer during a stabilization sequence. |
| Causes: | • MFP board (MFPB) • Printer control board (PRCB) |
| Remedy: | 1 Reboot the machine. - - 2 Check the flat cable between MFPB CN16C-PRCB CN4 for proper connection and correct as necessary. - - 3 Check the connected portion of the flat cable for any curled pattern or any scratches, and replace it if necessary. - - 4 Replace MFPB - - 5 Replace PRCB |
| Error code: | 4092 |
| Description: | I/F communication error (CNT detection) The communication between the MFPB and PRCB can not be completed even when elapsed a given period of time. |
| Causes: | • MFP board (MFPB) • Printer control board (PRCB)ntrol |
| Remedy: | 1 Reboot the machine. - - 2 Check the flat cable between MFPB CN16C-PRCB CN4 for proper connection and correct as necessary. - - 3 Check the connected portion of the flat cable for any curled pattern or any scratches, and replace it if necessary. - - 4 Replace MFPB 5 Replace PRCB |
| Error code: | 4101 |
| Description: | BD initialization error K After Polygon motor is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4501 |
| Description: | Laser malfunction • SOS signal is not detected even after the lapse of a given period of time after starting the laser output. • SOS signal is not detected for a given period of time during printing. |
| Causes: | • PH unit • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between PH unit-relay CN73- PRCB CN5 for proper connection and correct as necessary. - - 2 Replace the PH unit - - 3 Replace PRCB |
| Error code: | 4801 |
| Description: | Main unit board failure A faulty combination of the printer control board (PRCB) and the MFP board (MFPB) is detected. |
| Causes: | • MFP board (MFPB) • Printer control board (PRCB) |
| Remedy: | 1 Reboot the machine. - - 2 Replace MFPB - - 3 Replace PRCB |
| Error code: | 4802 |
| Description: | Main unit backup data miscompare The replacement of the printer control board is detected. |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 1. Call the Service mode to the screen. 2. Touch [Security Service Mode]. 3. Touch [Engine Data Backup]. 4. Touch [Engine Data Reflect Mode], and touch [OK]. 5. Check that the result “OK” appears. 6. Turn OFF the main power switch and turn it ON again more than 10 seconds after. - - 2 Update the firmware. - - 3 If the above actions do not solve the problem, contact KM. |
| Error code: | 4901 |
| Description: | FW/OS integrity verification error • NG results from verification of the hash value of the controller FW. • Faulty, damaged, or illegally written ROM data |
| Causes: | • MFP board (MFPB) • SSD board (SSDB) |
| Remedy: | 1 Reboot the machine. - - 2 Update the firmware. - - 3 Check the MFPB for proper connection and correct as necessary. - - 4 Check the SSDB for proper connection and correct as necessary. 5 Replace SSD 6 Replace MFPB |
| Error code: | 5102 |
| Description: | Main high-voltage error C Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board). |
| Causes: | Defective connector cable or poor contact in the connector. Defective high voltage PWB 1. Defective engine PWB. |
| Remedy: | Drum unit 1. Execute U030 Belt Mean Drum Motor and check that the drum motor can rotate. 2. Confirm that the drum or the drum screw can rotate. 3. Check that the discharger lamp is properly connected. 4. If it won’t rotate, replace the drum unit. Charger roller unit 1. Check that the high-voltage contacts are not distorted or adhered with foreign objects. 2. Reinstall the chrager roller unit.Or, replace the charger roller unit. High voltage PWB 1 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. High voltage PWB 1(YC2) and Engine PWB (YC16) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the High voltage PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 5307 |
| Description: | UFP fan motor failure The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • UFP fan motor (FM5) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between FM5-relay CN158-relay CN90-PRCB CN13 for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM5 operation check EXCB CN13-1 (OUT) EXCB CN13-3 (LOCK) 15-F 4 Replace FM5 - - 5 PRCB F2 conduction check - - 6 Replace PRCB |
| Error code: | 5351 |
| Description: | DC power supply fan motor failure The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • DC power supply fan motor (FM1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between FM1-relay CN304- PRCB CN3 for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM1 operation check PRCB CN3-10 (OUT) PRCB CN3-12 (LOCK) 7-L 4 Replace FM1 - - 5 PRCB F2 conduction check - - 6 Replace PRCB |
| Error code: | 5353 |
| Description: | Cooling fan motor/2 failure The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Cooling fan motor/2 (FM6)ning. • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between FM6-relay CN302- PRCB CN3 for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM6 operation check PRCB CN3-4 (OUT) PRCB CN3-6 (LOCK) 7-K 4 Replace FM6 - - 5 PRCB F2 conduction check - - 6 Replace PRCB |
| Error code: | 5357 |
| Description: | Cooling fan motor/1 failurening. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Cooling fan motor/1 (FM2) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between FM2-relay CN303- PRCB CN3 for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM2 operation check PRCB CN3-7 (OUT) PRCB CN3-9 (LOCK) 7-L 4 Replace FM2 - - 5 PRCB F2 conduction check - - 6 Replace PRCB |
| Error code: | 5501 |
| Description: | AC signal abnormality The zero cross signal is not input during fusing phase control. |
| Causes: | • Fusing unit • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the fusing unit-PRCB CN15, DCPS CN2 for proper connection and correct or change as necessary - - 3 Replace fusing unit - - 4 Replace PRCB - - 5 Replace DCPS |
| Error code: | 5601 |
| Description: | Engine control malfunction Engine control malfunction is detected with port monitor control. |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Check the connectors on the PRCB for proper connection and correct or change as necessary. - - 2 Rewrite the firmware. - - 3 Replace PRCB |
| Error code: | 5701 |
| Description: | Power supply malfunction A condition is detected in which no power is being supplied to the printer control board (PRCB). |
| Causes: | • PH unit • Toner supply motor/YM (M5) • Toner supply motor/CK (M6) • Front door switch (SW2) • Right door switch (SW3) • DC power supply (DCPS) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between SW2, SW3-DCPS CN10 for proper connection and correct as necessary. - - 2 Check the connector between M5, M6-PRCB CN22 for proper connection and correct as necessary. - - 3 Check the connector between PH unit-relay CN73- PRCB CN5 for proper connection and correct as necessary. - - 4 M5, M6 operation check PRCB CN22-1 to 4 (M5) PRCB CN22-5 to 8 (M6) 7-I 7-K 5 SW2, SW3 operation check DCPS CN10-1 to 3 1-F 6 Replace the PH unit - - 7 Replace DCPS - - 8 PRCB F5, F10 conduction check - - 9 Replace PRCB |
| Error code: | 6751 |
| Description: | CCD clamp/gain adjustment failure During the CCD gain adjustment, a condition in which the peak value of the output data is equal to, or less than, 64 occurs three consecutive times during retries. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 6790 |
| Description: | AFE offset adjustment error During the offset adjustment, the offset value does not fall within the predetermined range a total of three times including retries. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 6791 |
| Description: | AFE register setting error There is a mismatch between the set default values of the AFE gain/offset and the gain/offset values read thereafter. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 6792 |
| Description: | White reference plate search error The black/white edge on the shading plate cannot be detected during initialization. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 6793 |
| Description: | Scanner communication error A communication error of some sort occurs between the controller and the scanner. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 Replace MFPB |
| Error code: | 9401 |
| Description: | Exposure lamp lighting failure detected The intensity of the lamp is not stabilized within a predetermined period of time during the lamp stabilization check process in a lamp warm-up cycle. |
| Causes: | • Scanner unit • MFP board (MFPB) |
| Remedy: | 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 MFPB F102, F105 conduction check - - 7 Replace MFPB |
| Error code: | C151 |
| Description: | ROM contents error upon startup (MSC) A fault is detected in a sequence of ROM contents check of the MFPB during starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace MFPB |
| Error code: | C15C |
| Description: | Engine Flash ROM writing error A flash ROM writing sequence is interrupted in its mid-operation due to, for example, power being shut off. |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. - - 3 Replace PRCB |
| Error code: | C15D |
| Description: | Engine Flash ROM device error An erase error or other device fault occurs during flash ROM writing. |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. - - 3 Replace PRCB |
| Error code: | C15E |
| Description: | Engine FW download communication fault Irregular data is received during FW downloading. |
| Causes: | • MFP board (MFPB) • Printer control board (PRCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace MFPB - - 4 Replace PRCB |
| Error code: | C161 |
| Description: | Firmware update error A firmware updating sequence is not normally terminated. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the cable used for updating the firmware for proper connection and correct any faulty connection as necessary. - - 2 Check the firmware updating file; if the file is not correct, update the firmware again. - - 3 Check the firmware updating procedure; if the procedure is not correct, update the firmware again. 4 Update the firmware again. 5 Check the MFPB connector for proper connection and correct any faulty connection as necessary. 6 Replace MFPB |
| Error code: | C163 |
| Description: | Faulty destination • The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked. • Hardware signal is not fixed when the Boot started. |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Rewrite the firmware. - - 2 Replace PRCB - - 1. Turn OFF the main power switch and replace the current PRCB with a new one. 2. Update the PRCB firmware. 3. After completing the firmware update, turn OFF and ON the main power switch and check to see that warm-up is started. 4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the MFPB. 3 If the above actions do not solve the problem, contact KM. |
| Error code: | C164 |
| Description: | ROM contents error (MSC) The wrong model of firmware is detected in the MFP board when the main power switch is turned ON. |
| Causes: | • Printer control board (PRCB) • MFP board (MFPB) |
| Error code: | D004 |
| Description: | Hard disk access error (connection failure) Unable to communicate between the hard disk and MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace the corresponding board. - - 4 If the above actions do not solve the problem, contact KM. |
| Error code: | D091 |
| Description: | Hard disk full error The area made available as a user area is full during access to the hard disk. |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | 1 Delete jobs saved using [Document Print/ Delete] to thereby increase the portion of the user area available for use. - - 2 Check the hard disk connector MFPB CN5 and CN13 for proper connection and correct any faulty connection as necessary. - - 3 Using [Administrator Settings] -> [Security Settings] -> [HDD Settings] -> [HDD Format], format the HDD. - - 4 Replace the hard disk. - - 5 Replace MFPB. |
| Error code: | D092 |
| Description: | No hard disk (found during a disk check) The hard disk is not mounted.sk |
| Causes: | Hard disk |
| Remedy: | 1 Install and format the hard disk. |
| Error code: | D093 |
| Description: | Wrong hard disk (found during a disk check) • A hard disk intended for another model is mounted. • The hard disk capacity is short. |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | 1 Replace the hard disk. - - 2 Format hard disk. |
| Error code: | D094 |
| Description: | Hard disk check disk error HDD is damaged. |
| Causes: | Hard disk |
| Remedy: | 1 Replace the hard disk. - - 2 Format hard disk. |
| Error code: | D095 |
| Description: | Hard disk recovered (requiring reboot) HDD is damaged. |
| Causes: | Hard disk |
| Remedy: | 1 Turn OFF/ON the main power switch. - - 2 If the above actions do not solve the problem, contact KM. |
| Error code: | D096 |
| Description: | Hard disk access fault HDD is damaged. |
| Causes: | Hard disk |
| Remedy: | 1 Replace the hard disk. - - 2 Format hard disk. |
| Error code: | D3A0, D3A2 |
| Description: | Counter error A write error occurs in the counter area. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the MFPB for its mounting condition and correct any faulty condition. - - 2 Replace MFPB - - 3 If the same trouble code persists after the abovementioned procedures, the EEPROM is probably damaged. |
| Error code: | D3F1 |
| Description: | Occur:The drum counter is over the life limit, and detect toner empty. |
| Remedy: | Push the ONLINE SW when change the new Image Drum. |
| Error code: | D3F4 |
| Description: | Occur:The drum counter is over the life limit, and detect toner empty. |
| Remedy: | Auto reset when change the new drum. |
| Error code: | D501 |
| Description: | FLASH error The SSD board (SSDB) develops a fault. |
| Causes: | • MFP board (MFPB) • SSD board (SSDB) |
| Remedy: | 1 Check the SSD for its mounting condition and correct any faulty condition. - - 2 Replace MFPB |
| Error code: | DC00 |
| Description: | EEPROM fault 1 Printer control board (PRCB) |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Check the connectors on the PRCB for proper connection and correct any faulty connection as necessary. - - 2 Replace PRCB |
| Error code: | DC10 |
| Description: | EEPROM fault 2 |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Check the connectors on the PRCB for proper connection and correct any faulty connection as necessary. - - 2 Replace PRCB |
Парткод
Название
Konica Minolta IUP22K Блок проявки черный
Konica Minolta IUP22Y Блок проявки желтый
Konica Minolta IUP22M Блок проявки пурпурный
Konica Minolta IUP22C Блок проявки голубой
Konica Minolta FUP05 Печка в сборе
Konica Minolta Емкость отработанного тонера
Konica Minolta TFP07 Блок ремня переноса
Konica Minolta TFP06 Ролик переноса
Konica Minolta TNP48K Тонер-картридж черный
Konica Minolta TNP48Y Тонер-картридж желтый
Konica Minolta TNP48M Тонер-картридж пурпурный
Konica Minolta TNP48C Тонер-картридж голубой
