Konica-Minolta bizhub C552DS
Рейтинг
Модули
2ND PAPER FEED
TONER COLLECT SECTION
BOTTLE DRIVE SECTION
MAIN FRAME
IR FRAME
SCANNER SECTION 2
PH UNIT
LCC LENGTH CONVEYANCE SECTION
ADF GLASS CLEANING SECTION
DOOR SAFE SWITCH
EXTERNAL PARTS 2
CONTROL PANEL 2
EXTERNAL PARTS
TONER SUPPLY SECTION 2
MAIN DRIVE UNIT
LCC DRIVE
REGISTRATION SENSOR
SHIELD BOX 2
ADU 2
ADF CIS SECTION
MANUAL FEED TRAY UNIT 4
FUSING DRIVE UNIT
TONER RAIL
CCD UNIT/SCANNER DRIVE
LEVEL CONVEYANCE SECTION
OZONE DUCT
PAPER EXIT CONVEYANCE SECTION 3
I/U FRAME SECTION
ADU
REAR ELECTRICAL SECTION
MANUAL FEED TRAY UNIT 3
ADF PAPER FEED TRAY 3
FUSING SECTION
MAIN POWER SUPPLY UNIT
LEVEL CONVEYANCE SECTION 2
1ST PAPER FEED 2
CASSETTE ASSY 2
IR BOARD SECTION
LCC CASSETTE RAIL
PAPER EXIT CONVEYANCE SECTION
SHIELD BOX
SCANNER SECTION
TRANSFER RAIL SECTION
SHIELD BOX 3
SIZE DETECTING SECTION
ADF PAPER FEED TRAY 2
ADF CIS CLEANING SECTION 2
Control panel
TRANSFER UNIT
ADF READ GUIDE SECTION 2
CASSETTE TRAY
1000-SHEET PAPER FEED SECTION 2
1500-SHEET TRAY
ADF LEFT COVER SECTION
IH POWER SUPPLY
MANUAL FEED TRAY UNIT
1ST PAPER FEED
EJECT DRIVE SECTION
ADF CONVEYANCE SECTION
REAR FAN SECTION 2
CONTACT SECTION
2ND PAPER FEED 2
PAPER EXIT CONVEYANCE SECTION 2
1500-SHEET PAPER FEED SECTION 2
REAR FAN SECTION
CASSETTE RAIL
ADF READ GUIDE SECTION
CASSETTE ASSY
IR COVER
ADF PAPER FEED TRAY
ADF CIS CLEANING SECTION
ERASE LAMP
HIGH VOLTAGE UNIT
1000-SHEET TRAY
EXTERNAL PARTS 4
TONER SUPPLY SECTION
ADF EXTERNAL PARTS
I/U LOCK LEVER
1500-SHEET PAPER FEED SECTION
MANUAL FEED TRAY UNIT 2
EXTERNAL PARTS 3
1000-SHEET PAPER FEED SECTION
ROTATION DETECTING SENSOR
REVERSAL UNIT
PAPER EXIT SECTION
Детали DOOR SAFE SWITCH
| Деталь: | Paper feed Door /Lower |
| Парткод: | A00J 5717 01 |
| Деталь: | Attaching Cover |
| Парткод: | A00J 5746 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5666 00 |
| Деталь: | Lock Claw /Front |
| Парткод: | A00J 5737 01 |
| Деталь: | ROLL |
| Парткод: | 4030 3122 01 |
| Деталь: | PULLING SPRING /LOWER |
| Парткод: | A00J 5745 00 |
| Деталь: | Idler Shaft |
| Парткод: | A00J 5741 00 |
| Деталь: | Guide Plate /Lower |
| Парткод: | A0P0 5719 00 |
| Деталь: | Lock Catch |
| Парткод: | A00J 5742 01 |
| Деталь: | HOLDING GUIDE |
| Парткод: | A0P0 5676 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3016 12 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 5723 00 |
| Деталь: | GEAR 30T |
| Парткод: | 4425 3013 01 |
| Деталь: | CLUTCH |
| Парткод: | A00J 5635 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | Shaft /P |
| Парткод: | A00J 5640 00 |
| Деталь: | GEAR 29T |
| Парткод: | 4030 3008 01 |
| Деталь: | Paper feed Holder |
| Парткод: | A00J 5601 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5603 02 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | SHAFT |
| Парткод: | 4040 3097 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | Paper feed Shaft |
| Парткод: | A0P0 5602 00 |
| Деталь: | Release Lever |
| Парткод: | A00J 5673 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5668 01 |
| Деталь: | SHAFT |
| Парткод: | A00J 5665 00 |
| Деталь: | Paper feed Frame |
| Парткод: | A00J 5604 00 |
| Деталь: | CONVEYANCE DRIVE CLUTCH |
| Парткод: | 57AA 8203 0 |
| Деталь: | Stopper Door |
| Парткод: | A00J 5736 01 |
| Деталь: | Guide Plate /Upper |
| Парткод: | A0P0 5718 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5739 00 |
| Деталь: | Lock Claw /Rear |
| Парткод: | A00J 5738 00 |
| Деталь: | Paper feed 2 assy |
| Парткод: | A0P0 R721 00 |
| Деталь: | Fixing Plate /Right |
| Парткод: | A0P0 3648 00 |
| Деталь: | KNOB |
| Парткод: | A00J 3650 01 |
| Деталь: | Guide Part /Right |
| Парткод: | A0P0 3660 00 |
| Деталь: | Bottle(Toner Collection) |
| Парткод: | A0XP WY1 |
| Деталь: | Guide Part /Middle |
| Парткод: | A0P0 3662 00 |
| Деталь: | Collection Shutter |
| Парткод: | A00J 3611 00 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 3612 00 |
| Деталь: | Collection Pipe |
| Парткод: | A00J 3617 00 |
| Деталь: | Conveyance Screw |
| Парткод: | A00J 3608 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0901 01 |
| Деталь: | Guide Part /Left |
| Парткод: | A0P0 3661 00 |
| Деталь: | GEAR 27T |
| Парткод: | A0P0 3629 00 |
| Деталь: | Drive Gear /10 17T |
| Парткод: | A0P0 3641 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | SHAFT |
| Парткод: | A0P0 3642 00 |
| Деталь: | Fixing Plate |
| Парткод: | A0P0 R7A0 00 |
| Деталь: | Fixing Plate /Left |
| Парткод: | A0P0 3649 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 3663 01 |
| Деталь: | Collection Casing |
| Парткод: | A0P0 3607 00 |
| Деталь: | Bushing /B |
| Парткод: | 65AA 3250 1 |
| Деталь: | Drive Shaft /2 |
| Парткод: | A00J 3619 00 |
| Деталь: | GEAR 20T |
| Парткод: | A00J 3627 00 |
| Деталь: | Gear 38/35T |
| Парткод: | A00J 3630 00 |
| Деталь: | BUSHING |
| Парткод: | A0P0 3640 00 |
| Деталь: | GEAR 30T |
| Парткод: | A00J 3625 00 |
| Деталь: | Gear 30/20T |
| Парткод: | A00J 3624 00 |
| Деталь: | GEAR 28T |
| Парткод: | A0P0 3685 00 |
| Деталь: | Drive Shaft /3 |
| Парткод: | A00J 3620 00 |
| Деталь: | Stepping motor |
| Парткод: | A00J M121 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0 3609 00 |
| Деталь: | Gear18T |
| Парткод: | A00J 3626 00 |
| Деталь: | GEAR 40T |
| Парткод: | A00J 3628 00 |
| Деталь: | Gear26T |
| Парткод: | A0P0 3684 00 |
| Деталь: | Drive Shaft /1 |
| Парткод: | A00J 3618 00 |
| Деталь: | BUSHING |
| Парткод: | A0P0 3682 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 3686 00 |
| Деталь: | Agitating Paddle |
| Парткод: | A0P0 3681 00 |
| Деталь: | GEAR 38T |
| Парткод: | A00J 3610 00 |
| Деталь: | Sealing Shutter |
| Парткод: | A00J 3654 02 |
| Деталь: | Toner collection assy |
| Парткод: | A0P0 R713 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 3664 00 |
| Деталь: | Toner Supply Duct Assy |
| Парткод: | A0P0 R742 00 |
| Деталь: | Drive Gear /3 40T |
| Парткод: | A00J 4031 00 |
| Деталь: | Drive Gear /2 75/40T |
| Парткод: | A00J 4030 00 |
| Деталь: | Drive Holder /Right |
| Парткод: | A00J 4026 00 |
| Деталь: | Drive Gear /1 70/35T |
| Парткод: | A00J 4029 00 |
| Деталь: | GEAR 40T |
| Парткод: | A00J 4040 00 |
| Деталь: | SPRING |
| Парткод: | 4038 5411 01 |
| Деталь: | COUPLING |
| Парткод: | A00J 4041 02 |
| Деталь: | GUIDE |
| Парткод: | 4038 5413 01 |
| Деталь: | COLLAR |
| Парткод: | 4038 5407 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 5412 02 |
| Деталь: | Fixing Plate /Right |
| Парткод: | A00J 4028 01 |
| Деталь: | MOTOR |
| Парткод: | 9314 1300 21 |
| Деталь: | Fixing Plate /Left |
| Парткод: | A00J 4038 00 |
| Деталь: | GEAR 40T |
| Парткод: | A00J 4037 00 |
| Деталь: | Drive Holder /Left |
| Парткод: | A00J 4027 00 |
| Деталь: | Drive Wiring /1 |
| Парткод: | A0P0 N109 00 |
| Деталь: | BOTTLE DRIVE-C BK |
| Парткод: | A00J R713 11 |
| Деталь: | BOTTLE DRIVE-YM |
| Парткод: | A00J R712 11 |
| Деталь: | Protection Plate |
| Парткод: | A00J 1429 00 |
| Деталь: | Hold Plate /1 |
| Парткод: | A0P0 1051 00 |
| Деталь: | Cover Handle |
| Парткод: | A0P0 1655 00 |
| Деталь: | Hold Plate /2 |
| Парткод: | A0P0 1052 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J 5952 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1024 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1053 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1382 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1383 00 |
| Деталь: | PLATE |
| Парткод: | A00J 1065 00 |
| Деталь: | Castor |
| Парткод: | A0P0 1090 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 4556 M100 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1377 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1354 00 |
| Деталь: | SEESAW-SWITCH |
| Парткод: | 4038 M600 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1345 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1043 11 |
| Деталь: | Stay /Lower |
| Парткод: | A00J 1014 00 |
| Деталь: | Stay /Upper |
| Парткод: | A0P0 1013 11 |
| Деталь: | RUBBER FOOT |
| Парткод: | A0P0 1046 00 |
| Деталь: | PLATE |
| Парткод: | A00J 1064 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1044 00 |
| Деталь: | SHEET |
| Парткод: | A0P0 1096 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1054 00 |
| Деталь: | Cover Handle |
| Парткод: | A00J 1646 00 |
| Деталь: | THERMISTOR |
| Парткод: | A0P0 M503 00 |
| Деталь: | Side plate /Middle |
| Парткод: | A00J 1016 03 |
| Деталь: | Temperature Relay harness |
| Парткод: | A0P0 N12P 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1487 01 |
| Деталь: | LABEL |
| Парткод: | 0957 1491 01 |
| Деталь: | Side plate /Upper |
| Парткод: | A0P0 1015 01 |
| Деталь: | Sealing Part /2 |
| Парткод: | A0P0 1093 00 |
| Деталь: | PROTECTION PART |
| Парткод: | A0P0 1421 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1027 00 |
| Деталь: | Guide Holder |
| Парткод: | A00J 5868 00 |
| Деталь: | COVER |
| Парткод: | A00J 1638 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 2676 00 |
| Деталь: | SEAL |
| Парткод: | 4581 1625 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2675 01 |
| Деталь: | REED SWITCH |
| Парткод: | 9334 2610 12 |
| Деталь: | LOUDSPEAKER |
| Парткод: | 4040 M401 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2638 00 |
| Деталь: | FRAME |
| Парткод: | A0P0 2620 00 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 61 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2622 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0P0 2631 00 |
| Деталь: | GUIDE |
| Парткод: | A0P0 2673 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0P0 2634 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0P0 2670 00 |
| Деталь: | SEAL |
| Парткод: | A00J 2629 01 |
| Деталь: | SEAL |
| Парткод: | A00J 2630 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2818 01 |
| Деталь: | Mounting Plate /Right rear |
| Парткод: | A0P0 2633 00 |
| Деталь: | SEAL |
| Парткод: | A00J 1667 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2678 00 |
| Деталь: | FRAME |
| Парткод: | A0P0 2621 02 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 9J07 2108 02 |
| Деталь: | FRAME |
| Парткод: | A0P0 2619 00 |
| Деталь: | Holding Plate |
| Парткод: | A1DM 2688 01 |
| Деталь: | Slit Glass Assy |
| Парткод: | A1DM R700 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 1692 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A1DM 2660 00 |
| Деталь: | CUSHION |
| Парткод: | A0ED 2681 00 |
| Деталь: | COVER |
| Парткод: | A1DM 2675 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0ED 2687 00 |
| Деталь: | Support Plate |
| Парткод: | A0P0 1012 01 |
| Деталь: | SPRING |
| Парткод: | 4038 2294 01 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0 1077 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2295 01 |
| Деталь: | Holder /Black |
| Парткод: | A0P0 1076 00 |
| Деталь: | SPRING |
| Парткод: | 4038 2293 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Drawer CN |
| Парткод: | V651 0200 04 |
| Деталь: | Guide Post |
| Парткод: | A00J 1056 01 |
| Деталь: | Positioning Pin /Front |
| Парткод: | A0P0 3824 00 |
| Деталь: | Guide Post |
| Парткод: | A00J 1057 00 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326 1110 51 |
| Деталь: | HOLDER |
| Парткод: | A00J 1359 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 1023 01 |
| Деталь: | POSITIONING PLATE |
| Парткод: | A00J 1021 01 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | A1DM R701 00 A1DN R700 00 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | V502 0100 26 |
| Деталь: | SUPPORT |
| Парткод: | A0P0 N12G 00 |
| Деталь: | Control Relay harness /3 |
| Парткод: | A0P0 H003 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1375 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1374 00 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 6094 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0902 01 |
| Деталь: | SCREW |
| Парткод: | 4036 5966 01 |
| Деталь: | Mounting Plate /F |
| Парткод: | A00J 6095 01 |
| Деталь: | ROLLER |
| Парткод: | A00J 5722 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6091 00 |
| Деталь: | BALL BEARING |
| Парткод: | A00J 6179 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6087 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6088 00 |
| Деталь: | MOUNTING PLATE / UP/DOWN MOTOR |
| Парткод: | A00J R7AM 00 |
| Деталь: | Heater Relay harness |
| Парткод: | A00J N10X 00 |
| Деталь: | Brush Motor |
| Парткод: | A0P0 M100 00 |
| Деталь: | Slide Shaft |
| Парткод: | 56AA 1733 0 |
| Деталь: | TERMINAL ROCKING SPRING |
| Парткод: | 56AA 1708 0 |
| Деталь: | Mounting Plate /Rear |
| Парткод: | A00J 6089 00 |
| Деталь: | PFU Relay harness |
| Парткод: | A0P0 N11G 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6090 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6093 00 |
| Деталь: | BALL BEARING |
| Парткод: | A00V 2406 00 |
| Деталь: | CLUTCH ASSY |
| Парткод: | A00J 6098 00 |
| Деталь: | PFU Relay harness /3 |
| Парткод: | A00J N11C 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6092 01 |
| Деталь: | Protection Cover /S |
| Парткод: | A00J 6170 00 |
| Деталь: | WASHER |
| Парткод: | A00J 6607 00 |
| Деталь: | Fixing Plate /F |
| Парткод: | A108 2679 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1500 21 |
| Деталь: | Power Source Board ASSY |
| Парткод: | A108 H002 00 |
| Деталь: | Cooling Duct /C |
| Парткод: | A108 2691 00 |
| Деталь: | Holding Part |
| Парткод: | A108 2712 00 |
| Деталь: | Cooling Duct /C |
| Парткод: | A108 2677 02 |
| Деталь: | Sealing Part /C |
| Парткод: | A108 2680 00 |
| Деталь: | Inverter unit |
| Парткод: | A108 M400 00 |
| Деталь: | Wiring Guide /C |
| Парткод: | A108 2686 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0HU 2617 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0HU 2610 00 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1910 92 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0HU 2612 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A108 2718 00 |
| Деталь: | Slide Part |
| Парткод: | A0HU 2603 00 |
| Деталь: | ARM |
| Парткод: | A0HU 3003 00 |
| Деталь: | PULLEY |
| Парткод: | A0HU 2501 00 |
| Деталь: | FLANGE |
| Парткод: | A0HU 2505 00 |
| Деталь: | BALL BEARING |
| Парткод: | A00J 2112 00 |
| Деталь: | SPACER |
| Парткод: | A0HU 2619 00 |
| Деталь: | SHAFT |
| Парткод: | A108 3000 01 |
| Деталь: | SHEET |
| Парткод: | A108 3001 01 |
| Деталь: | BRUSH |
| Парткод: | A108 3002 00 |
| Деталь: | GUIDE |
| Парткод: | A0HU 2611 01 |
| Деталь: | SHEET |
| Парткод: | A0HU 2613 00 |
| Деталь: | BUSHING |
| Парткод: | A0HU 3005 00 |
| Деталь: | Fixing Ring |
| Парткод: | A0HU 3006 01 |
| Деталь: | ARM |
| Парткод: | A0HU 3004 00 |
| Деталь: | Guide Plate /C |
| Парткод: | A00J 4034 02 |
| Деталь: | Guide Plate /B |
| Парткод: | A1DM 4033 00 |
| Деталь: | REED SWITCH |
| Парткод: | 9334 2610 12 |
| Деталь: | Mounting Plate /B |
| Парткод: | A00J 1358 00 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06 M601 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 1346 00 |
| Деталь: | Torsion Coil |
| Парткод: | A00J 1365 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1352 01 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J 1428 00 |
| Деталь: | Toner Relay harness |
| Парткод: | A0P0 N10B 00 |
| Деталь: | Guide Plate /A |
| Парткод: | A1DM 4032 00 |
| Деталь: | Light blocking Cover |
| Парткод: | A00J 1683 01 |
| Деталь: | Lens /A |
| Парткод: | A00J 1681 02 |
| Деталь: | Light blocking Plate |
| Парткод: | A00J 1688 01 |
| Деталь: | Cover Cassette /Right |
| Парткод: | A00J 1608 01 |
| Деталь: | Cover LCC Info |
| Парткод: | A00J 1611 02 |
| Деталь: | Light blocking Cover |
| Парткод: | A00J 1684 00 |
| Деталь: | PWB Assembly LED1 |
| Парткод: | A00J H00D 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1645 01 |
| Деталь: | COVER |
| Парткод: | A00J 1686 00 |
| Деталь: | COVER |
| Парткод: | A00J 1687 00 |
| Деталь: | INDICATING RELAY HARNESS/1 |
| Парткод: | A00J N10D 00 |
| Деталь: | LABEL |
| Парткод: | A1DM 9433 00 |
| Деталь: | LABEL |
| Парткод: | A1DN 9433 00 |
| Деталь: | Cover LCC Right |
| Парткод: | A00J 1610 01 |
| Деталь: | Cover LCC Right |
| Парткод: | A00J 1650 00 |
| Деталь: | Cover LCC Left |
| Парткод: | A00J 1649 03 |
| Деталь: | Cover LCC Left |
| Парткод: | A00J 1609 01 |
| Деталь: | HINGE |
| Парткод: | A0P0 1621 00 |
| Деталь: | Mounting Plate /B |
| Парткод: | A0P0 1626 00 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475 2603 02 |
| Деталь: | Label IU replace |
| Парткод: | A0P0 9440 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | BAND |
| Парткод: | 4120 1014 02 |
| Деталь: | Open/close Cover /Front |
| Парткод: | A0P0 1603 01 |
| Деталь: | COVER |
| Парткод: | A0P0 1679 02 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1915 00 |
| Деталь: | WASHER |
| Парткод: | A00J 1929 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1911 01 |
| Деталь: | WASHER |
| Парткод: | A00J 1919 00 |
| Деталь: | ARM |
| Парткод: | A0P0 1914 00 |
| Деталь: | LEVER |
| Парткод: | A0P0 1922 00 |
| Деталь: | HANDLE |
| Парткод: | A0P0 1925 00 |
| Деталь: | Read Cover /Front |
| Парткод: | A0P0 1674 00 |
| Деталь: | LABEL |
| Парткод: | A0ED 9465 00 |
| Деталь: | Operation panel mounting assy |
| Парткод: | A0P0 R706 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1677 00 |
| Деталь: | Read Cover /2 |
| Парткод: | A0P0 1697 00 |
| Деталь: | Read Cover /1 |
| Парткод: | A0P0 1675 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1921 00 |
| Деталь: | LEVER |
| Парткод: | A0P0 1923 00 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 1926 01 |
| Деталь: | Support Screw |
| Парткод: | A00J 1918 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1912 00 |
| Деталь: | FRAME |
| Парткод: | A0P0 2632 01 |
| Деталь: | COLLAR |
| Парткод: | A00J 1917 00 |
| Деталь: | ARM |
| Парткод: | A0P0 1913 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1916 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1680 00 |
| Деталь: | Support Shaft |
| Парткод: | A00J 1928 00 |
| Деталь: | Label Emperon |
| Парткод: | A011 9462 00 |
| Деталь: | Paper exit Cover /Right |
| Парткод: | A00J 1635 02 |
| Деталь: | Cover /Front |
| Парткод: | A00J 1604 03 |
| Деталь: | BAND |
| Парткод: | 4120 1014 02 |
| Деталь: | COVER |
| Парткод: | A00J 1636 01 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475 2603 02 |
| Деталь: | Mounting Plate /D |
| Парткод: | A00J 1660 01 |
| Деталь: | Open/close Cover |
| Парткод: | A00J 1602 01 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | Logo Mark |
| Парткод: | A00J 9455 00 |
| Деталь: | CATCH |
| Парткод: | 4030 1040 02 |
| Деталь: | MAGNET |
| Парткод: | 9326 2820 11 |
| Деталь: | Toner Wiring |
| Парткод: | A0P0 N10G 00 |
| Деталь: | Cover /Inside |
| Парткод: | A00J 1651 03 |
| Деталь: | SPACER |
| Парткод: | A00J 4047 00 |
| Деталь: | LABEL |
| Парткод: | A0P0 9486 00 |
| Деталь: | Paper exit Cover /Rear |
| Парткод: | A00J 1634 01 |
| Деталь: | Paper exit Cover /Front |
| Парткод: | A00J 1601 00 |
| Деталь: | Paper exit Cover /Right |
| Парткод: | A00J 1664 00 |
| Деталь: | Label TC Change |
| Парткод: | A00J 9403 03 |
| Деталь: | Open/close Shaft |
| Парткод: | A00J 1647 01 |
| Деталь: | Paper exit Cover /Rear |
| Парткод: | A00J 1663 00 |
| Деталь: | Regulating Block /Black |
| Парткод: | A0P0 4048 00 |
| Деталь: | Regulating Block /Black |
| Парткод: | A0P0 4058 00 |
| Деталь: | Regulating Block /Black |
| Парткод: | A0P0 4059 00 |
| Деталь: | HOLDER |
| Парткод: | A00J 4075 00 |
| Деталь: | LABEL K |
| Парткод: | A00J 9407 00 |
| Деталь: | SEAL |
| Парткод: | A00J 4074 00 |
| Деталь: | Claw /Black |
| Парткод: | A0P0 1696 00 |
| Деталь: | LABEL C |
| Парткод: | A00J 9406 00 |
| Деталь: | PAWL |
| Парткод: | 4036 5325 02 |
| Деталь: | LABEL M |
| Парткод: | A00J 9405 00 |
| Деталь: | LABEL Y |
| Парткод: | A00J 9404 00 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038 1014 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2282 03 |
| Деталь: | CONNECTOR PIN |
| Парткод: | 4136 6751 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2281 04 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J 4046 01 |
| Деталь: | COVER |
| Парткод: | A0P0 4067 00 |
| Деталь: | Agitating Shaft |
| Парткод: | A00J 4006 11 |
| Деталь: | AGITAING PANEL |
| Парткод: | A00J R744 00 |
| Деталь: | Bushing /B |
| Парткод: | 65AA 3250 1 |
| Деталь: | SEAL |
| Парткод: | A00J 4023 00 |
| Деталь: | Supply Casing |
| Парткод: | A00J 4001 12 |
| Деталь: | SEAL |
| Парткод: | 4036 5349 03 |
| Деталь: | TENSION SPRING |
| Парткод: | 4036 5348 01 |
| Деталь: | SHUTTER |
| Парткод: | 4036 5347 02 |
| Деталь: | Cover /Lower |
| Парткод: | A00J 4054 00 |
| Деталь: | TONER RELAY HARNESS/3 |
| Парткод: | A00J N121 00 |
| Деталь: | Gear 45T |
| Парткод: | A00J 4017 00 |
| Деталь: | Gear 38/35T |
| Парткод: | A00J 4018 00 |
| Деталь: | SEAL |
| Парткод: | A00J 4052 00 |
| Деталь: | Stepping motor |
| Парткод: | A00J M121 00 |
| Деталь: | DRIVEPANEL/H |
| Парткод: | A00J R7A1 00 |
| Деталь: | Gear 17/44T |
| Парткод: | A00J 4019 00 |
| Деталь: | Seal /A |
| Парткод: | A00J 4022 00 |
| Деталь: | GEAR 22T |
| Парткод: | A00J 4016 00 |
| Деталь: | Supply Roller |
| Парткод: | A00J 4005 00 |
| Деталь: | SEAL |
| Парткод: | A00J 4073 00 |
| Деталь: | Spring /A |
| Парткод: | A00J 4014 01 |
| Деталь: | Cover /Upper |
| Парткод: | A00J 4003 00 |
| Деталь: | Regulating Claw |
| Парткод: | A00J 4012 00 |
| Деталь: | Shutter /H |
| Парткод: | A00J 4004 01 |
| Деталь: | Receiving Block /Left |
| Парткод: | A00J 4068 01 |
| Деталь: | Receiving Block /Right |
| Парткод: | A00J 4069 01 |
| Деталь: | Guide Cover /Left |
| Парткод: | A00J 4056 00 |
| Деталь: | Seal /S |
| Парткод: | A00J 4009 00 |
| Деталь: | Guide Cover /Right |
| Парткод: | A00J 4055 00 |
| Деталь: | LEVEL DETECTION SENSOR |
| Парткод: | 40AA 8803 1 |
| Деталь: | Panel /P |
| Парткод: | A00J 4066 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 4010 00 |
| Деталь: | Gear 88T |
| Парткод: | A0P0 2208 00 |
| Деталь: | Transfer Shaft |
| Парткод: | A0P0 2203 00 |
| Деталь: | BALL BEARING |
| Парткод: | A00V 2406 00 |
| Деталь: | Transfer Frame /C |
| Парткод: | A00J 2206 00 |
| Деталь: | GUIDE |
| Парткод: | 4036 3517 01 |
| Деталь: | TRANSFER FRAME/B |
| Парткод: | A00J R7B7 00 |
| Деталь: | STOPPER RING |
| Парткод: | 1164 3065 01 |
| Деталь: | Gear 59T |
| Парткод: | A00J 2201 02 |
| Деталь: | Reinforce Plate /T |
| Парткод: | A0P0 2289 00 |
| Деталь: | Transfer Gear /M 55/34T |
| Парткод: | A0P0 2281 00 |
| Деталь: | Pulling Spring |
| Парткод: | A0P0 2285 00 |
| Деталь: | Transfer Shaft /B |
| Парткод: | A0P0 2287 00 |
| Деталь: | Transfer Gear /Y 20T |
| Парткод: | A0P0 2282 00 |
| Деталь: | Transfer Frame /E |
| Парткод: | A0P0 2284 00 |
| Деталь: | Transfer freme / F |
| Парткод: | A0P0 R7A6 00 |
| Деталь: | brushless Motor /20 |
| Парткод: | A00J M114 01 |
| Деталь: | MOTOR |
| Парткод: | 9314 2300 21 |
| Деталь: | Brushless motor /30 |
| Парткод: | A00J M115 01 |
| Деталь: | DC Brushless motor |
| Парткод: | A0ED M101 00 |
| Деталь: | Gear 22/33T |
| Парткод: | A00J 2251 00 |
| Деталь: | Stepping motor |
| Парткод: | A02E M10C 01 |
| Деталь: | TRANSFER FRAME / D |
| Парткод: | A00J R7B6 00 |
| Деталь: | GEAR 16/64T |
| Парткод: | A00J 2250 00 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A0P0 R707 00 |
| Деталь: | PWB Assembly(PWB-EE ASSY) |
| Парткод: | A0P0 H00C 00 |
| Деталь: | Brushless motor /15 |
| Парткод: | A00J M110 00 |
| Деталь: | Gear 44/70T |
| Парткод: | A00J 2200 01 |
| Деталь: | PIN |
| Парткод: | 4004 2547 01 |
| Деталь: | Transfer Frame /A |
| Парткод: | A00J 2204 00 |
| Деталь: | Brushless motor /12 |
| Парткод: | A00J M113 00 |
| Деталь: | Stepping motor |
| Парткод: | A0P0 M122 00 |
| Деталь: | Drive Shaft /5 |
| Парткод: | A00J 6113 00 |
| Деталь: | Drive Shaft /1 |
| Парткод: | A00J 6169 00 |
| Деталь: | CLUTCH |
| Парткод: | A00J M200 00 |
| Деталь: | GEAR 32T |
| Парткод: | A00J 6121 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6177 00 |
| Деталь: | BALL BEARING |
| Парткод: | A00V 2406 00 |
| Деталь: | MOUNTING PLATE / LCC LENGTH CONVEYANCE |
| Парткод: | A00J R7AF 00 |
| Деталь: | Gear 31T |
| Парткод: | A00J 6162 00 |
| Деталь: | GEAR 44T |
| Парткод: | A00J 6163 00 |
| Деталь: | COLLAR |
| Парткод: | A00J 7009 00 |
| Деталь: | SHAFT STOPPER |
| Парткод: | 55VA 4212 0 |
| Деталь: | GEAR 25T |
| Парткод: | A00J 6125 00 |
| Деталь: | Fixing Plate /1 |
| Парткод: | A00J 6102 00 |
| Деталь: | Gear 40/33T |
| Парткод: | A00J 6116 00 |
| Деталь: | Timing belt 633L |
| Парткод: | A00J 6106 00 |
| Деталь: | Gear 67T |
| Парткод: | A00J 6115 00 |
| Деталь: | Holding Part /1 |
| Парткод: | A00J 6126 00 |
| Деталь: | Drive Shaft /1 |
| Парткод: | A00J 6108 01 |
| Деталь: | Fixing Plate |
| Парткод: | A00J 6103 00 |
| Деталь: | Pulley 33T |
| Парткод: | A00J 6122 00 |
| Деталь: | PIN |
| Парткод: | 4004 2547 01 |
| Деталь: | GEAR 29T |
| Парткод: | A00J 6117 00 |
| Деталь: | Regulating Part |
| Парткод: | A00J 6128 00 |
| Деталь: | Tension Roll |
| Парткод: | A0P0 6664 00 |
| Деталь: | Mounting plate /Belt tension |
| Парткод: | A0P0 R7A2 00 |
| Деталь: | BELT TENSION SPRING |
| Парткод: | 56QA 1519 0 |
| Деталь: | GEAR 30T |
| Парткод: | A00J 6119 00 |
| Деталь: | Drive Shaft /4 |
| Парткод: | A00J 6112 00 |
| Деталь: | DC Brushless motor |
| Парткод: | A0ED M101 00 |
| Деталь: | Gear 33T |
| Парткод: | A00J 6118 00 |
| Деталь: | Drive Shaft /2 |
| Парткод: | A00J 6110 00 |
| Деталь: | Drive Shaft /3 |
| Парткод: | A00J 6111 00 |
| Деталь: | COVER |
| Парткод: | A00J 1376 00 |
| Деталь: | MOUNTING PLATE / LCC DRIVE 2 |
| Парткод: | A00J R7AJ 00 |
| Деталь: | GEAR 29T |
| Парткод: | A00J 6164 00 |
| Деталь: | Gear 33T |
| Парткод: | A00J 6165 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6166 00 |
| Деталь: | GEAR 35T |
| Парткод: | A00J 6168 00 |
| Деталь: | GEAR 35T |
| Парткод: | A00J 6130 00 |
| Деталь: | GEAR 29T |
| Парткод: | A00J 6120 00 |
| Деталь: | WAVE WASHER |
| Парткод: | 1500 2660 13 |
| Деталь: | Mounting plate / LCC drive 1 |
| Парткод: | A0P0 R7A3 00 |
| Деталь: | Sensor Cover |
| Парткод: | A00J 7041 00 |
| Деталь: | Sensor Shutter |
| Парткод: | A00J 7111 01 |
| Деталь: | Guide Stopper |
| Парткод: | A00J 7029 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 7036 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0P0 7022 00 |
| Деталь: | PIN |
| Парткод: | 4025 3676 01 |
| Деталь: | Wiring Cover |
| Парткод: | A00J 7045 00 |
| Деталь: | Guide Holder /Left |
| Парткод: | A00J 7021 01 |
| Деталь: | LEVER |
| Парткод: | 4036 3673 01 |
| Деталь: | LEVER |
| Парткод: | A00J 7116 01 |
| Деталь: | HOLD PLATE |
| Парткод: | 4025 3674 02 |
| Деталь: | Removal guide assy |
| Парткод: | A0P0 R731 00 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A0P0 M504 00 |
| Деталь: | PHOTO SENSING ELEMENT |
| Парткод: | V869 9000 45 |
| Деталь: | Sensor Relay harness /4 |
| Парткод: | A00J N122 01 |
| Деталь: | Hold Wire /Front |
| Парткод: | A00J 7072 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 7061 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4643 4605 01 |
| Деталь: | Sensor Cover /2 |
| Парткод: | A00J 7044 00 |
| Деталь: | Plate spring /2 |
| Парткод: | A00J 7037 00 |
| Деталь: | TENSION SPRING |
| Парткод: | 4025 3556 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J 7028 00 |
| Деталь: | Plate spring /1 |
| Парткод: | A00J 7025 00 |
| Деталь: | Plate spring /3 |
| Парткод: | A00J 7038 00 |
| Деталь: | RESISTOR |
| Парткод: | 9454 4076 02 |
| Деталь: | STOPPER |
| Парткод: | 4036 3557 01 |
| Деталь: | PLATE NUT |
| Парткод: | 4002 5042 02 |
| Деталь: | GUIDE ASSY |
| Парткод: | A0P0 R750 00 |
| Деталь: | COVER |
| Парткод: | 4037 2247 01 |
| Деталь: | ELECTRICALLY CONDUCTIVE MATERIAL |
| Парткод: | 4037 6776 01 |
| Деталь: | SCREW |
| Парткод: | 4025 2283 01 |
| Деталь: | COVER |
| Парткод: | A0P0 1472 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0 1491 00 |
| Деталь: | Ope.unit Cable |
| Парткод: | A0P0 N150 00 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A0P0 N149 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1474 01 |
| Деталь: | COVER |
| Парткод: | A00J 1387 00 |
| Деталь: | SCREW |
| Парткод: | A00J 1396 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1449 00 |
| Деталь: | GUIDE RAIL |
| Парткод: | A00J 1367 00 |
| Деталь: | Control Relay harness /2 |
| Парткод: | A0P0 N12F 01 |
| Деталь: | PWB Assembly(PWB-MFP ASSY) |
| Парткод: | A0P0 H022 00 |
| Деталь: | PWB Assembly(PWB-MFP ASSY) |
| Парткод: | A0P0 H023 00 |
| Деталь: | MEMORY MODULES |
| Парткод: | V865 3000 26 |
| Деталь: | RAIL |
| Парткод: | A0P0 1447 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | COVER |
| Парткод: | A0P0 1330 02 |
| Деталь: | CUSHION |
| Парткод: | 4004 1829 02 |
| Деталь: | Controller Relay harness /1 |
| Парткод: | A0P0 N12R 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0P0 1459 00 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326 1910 31 |
| Деталь: | FERRITECORE |
| Парткод: | A0P0 M900 00 |
| Деталь: | PWB assembly(PWB-DS ASSY) |
| Парткод: | A0P0 H02A 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A1DM 1455 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A1DM 1458 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1473 00 |
| Деталь: | Cover /Upper |
| Парткод: | A00J 8102 01 |
| Деталь: | Guide Film |
| Парткод: | A00J 8163 00 |
| Деталь: | ACTUATOR |
| Парткод: | A00J 8132 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4657 3734 01 |
| Деталь: | Contact /4 |
| Парткод: | A0P0 8170 00 |
| Деталь: | Sensor Plate /Lower |
| Парткод: | A00J 8120 00 |
| Деталь: | Actuator /Lower |
| Парткод: | A00J 8119 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4657 3735 01 |
| Деталь: | Cover /Lower |
| Парткод: | A00J 8107 12 |
| Деталь: | ROLL |
| Парткод: | A00J 8141 01 |
| Деталь: | SHAFT |
| Парткод: | A00J 8144 11 |
| Деталь: | SCREW |
| Парткод: | 4036 5966 01 |
| Деталь: | SPRING |
| Парткод: | A00J 8145 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J 8162 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Wiring Cover |
| Парткод: | A00J 8154 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | GEAR 25T |
| Парткод: | A00J 8138 00 |
| Деталь: | Pulley 33/25T |
| Парткод: | A00J 8139 00 |
| Деталь: | Sensor Plate /Middle |
| Парткод: | A00J 8133 00 |
| Деталь: | Belt 160L |
| Парткод: | A00J 8111 00 |
| Деталь: | DRIVE FRAME / LOWER |
| Парткод: | A00J R7B0 00 |
| Деталь: | Stepping motor |
| Парткод: | A0P0 M121 00 |
| Деталь: | Protection Film |
| Парткод: | A0P0 8166 00 |
| Деталь: | Cover /Rear |
| Парткод: | A00J 8106 00 |
| Деталь: | LEVER |
| Парткод: | A00J 8161 00 |
| Деталь: | HOOK |
| Парткод: | A00J 8153 00 |
| Деталь: | ADU Wiring |
| Парткод: | A00J N113 00 |
| Деталь: | DRIVE FRAME / UPPER |
| Парткод: | A00J R7B1 00 |
| Деталь: | TIMING BELT 134L |
| Парткод: | 4657 3743 01 |
| Деталь: | Sensor Plate /Upper |
| Парткод: | A00J 8126 00 |
| Деталь: | Contact /1 |
| Парткод: | A0P0 8167 00 |
| Деталь: | Contact /2 |
| Парткод: | A0P0 8168 00 |
| Деталь: | Contact /3 |
| Парткод: | A0P0 8169 00 |
| Деталь: | Stepping motor |
| Парткод: | A0HT M102 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 2160 00 |
| Деталь: | Timing belt 184L |
| Парткод: | A108 2161 00 |
| Деталь: | Pulley 34T |
| Парткод: | A108 2162 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 2537 01 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N10A 00 |
| Деталь: | Protection Cover /Rear |
| Парткод: | A108 2681 00 |
| Деталь: | Ground Spring /C |
| Парткод: | A108 2685 00 |
| Деталь: | Reinforce Stay /4 |
| Парткод: | A108 8901 00 |
| Деталь: | BRACKET |
| Парткод: | A0HT 8919 00 |
| Деталь: | Paper exit Guide /1 |
| Парткод: | A108 8900 00 |
| Деталь: | GUIDE |
| Парткод: | A108 8908 00 |
| Деталь: | COLLAR |
| Парткод: | 9J08 2104 01 |
| Деталь: | SHAFT |
| Парткод: | 9J07 8900 00 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | A108 8902 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108 R900 00 |
| Деталь: | GUIDE |
| Парткод: | A108 8906 00 |
| Деталь: | CIS UNIT |
| Парткод: | A108 R703 00 |
| Деталь: | Protection Cover /Front |
| Парткод: | A108 2676 00 |
| Деталь: | BUSHING |
| Парткод: | 1200 3121 09 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | Stepping motor |
| Парткод: | A0HU M100 00 |
| Деталь: | TIMING BELT |
| Парткод: | A0HU 2508 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 2629 00 |
| Деталь: | FLANGE |
| Парткод: | A0HU 2512 00 |
| Деталь: | PULLEY |
| Парткод: | A0HU 2511 00 |
| Деталь: | Belt 260L |
| Парткод: | A108 2628 00 |
| Деталь: | PULLEY |
| Парткод: | A0HU 2503 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 2659 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07 4912 01 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N109 00 |
| Деталь: | LEVER |
| Парткод: | 9J07 4911 01 |
| Деталь: | Bypass Cover /Rear |
| Парткод: | A00J 5980 01 |
| Деталь: | MOTOR ASSY |
| Парткод: | 4037 R710 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5934 00 |
| Деталь: | MOUNTING PLATE / BYPASS 1 |
| Парткод: | A00J R7AR 00 |
| Деталь: | GEAR 22T |
| Парткод: | A00J 5918 00 |
| Деталь: | SHUTTER |
| Парткод: | A0P0 5983 00 |
| Деталь: | Guide Sheet |
| Парткод: | A00J 5876 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4036 1410 01 |
| Деталь: | Bypass Holder /Front |
| Парткод: | A0P0 5965 00 |
| Деталь: | Guide Sheet |
| Парткод: | A0P0 5974 00 |
| Деталь: | Guide Sheet |
| Парткод: | A00J 5891 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J 5877 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5912 01 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 5873 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 5920 01 |
| Деталь: | Mounting Plate /S |
| Парткод: | A00J 5910 02 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 5911 00 |
| Деталь: | Holder /S |
| Парткод: | A00J 5909 01 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 5975 11 |
| Деталь: | Fieldroller/1 assy |
| Парткод: | A0P0 R741 00 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3125 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J 5913 00 |
| Деталь: | SEAL |
| Парткод: | A00J 5858 00 |
| Деталь: | Gear 14/24T |
| Парткод: | A00J 5931 01 |
| Деталь: | Gear 14/50T |
| Парткод: | A00J 5933 00 |
| Деталь: | Mounting Plate /Rear |
| Парткод: | A00J 5879 01 |
| Деталь: | Paperfeed Relay harness /5 |
| Парткод: | A00J N114 02 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0 5881 00 |
| Деталь: | Support Shaft |
| Парткод: | A00J 5986 00 |
| Деталь: | COVER |
| Парткод: | A00J 5887 01 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J 5957 02 |
| Деталь: | Stepping motor |
| Парткод: | A0P0 M122 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J 5963 00 |
| Деталь: | Wiring Holder |
| Парткод: | A00J 5863 00 |
| Деталь: | MUUNTINGPLATE/BYPASS2 |
| Парткод: | A00J R7AS 00 |
| Деталь: | Bypass field roller assy |
| Парткод: | A0P0 R729 00 |
| Деталь: | Brushless motor /30 |
| Парткод: | A0P0 M115 00 |
| Деталь: | Pressure Gear /4 40T |
| Парткод: | A0P0 2359 00 |
| Деталь: | BUSHING |
| Парткод: | 9J06 2101 00 |
| Деталь: | BALL BEARING |
| Парткод: | A00V 2406 00 |
| Деталь: | FUSING DRIVE FRAME |
| Парткод: | A00J R7B9 11 |
| Деталь: | TENSION SPRING |
| Парткод: | 4004 2582 01 |
| Деталь: | Gear 58/62T |
| Парткод: | A00J 2306 00 |
| Деталь: | GEAR 30T |
| Парткод: | A00J 2303 00 |
| Деталь: | Gear 52/30T |
| Парткод: | A00J 2300 00 |
| Деталь: | BUSHING |
| Парткод: | 1200 3121 09 |
| Деталь: | Gear 33T |
| Парткод: | A00J 2307 00 |
| Деталь: | Paper exit Shaft /1 |
| Парткод: | A00J 2318 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J 2324 00 |
| Деталь: | Gear 38/38T |
| Парткод: | A00J 2301 00 |
| Деталь: | Paper exit Bearing /1 |
| Парткод: | A00J 2321 00 |
| Деталь: | Fusing Shaft /1 |
| Парткод: | A00J 2312 00 |
| Деталь: | Gear18T |
| Парткод: | A00J 2308 00 |
| Деталь: | Gear 23T |
| Парткод: | A00J 2305 00 |
| Деталь: | PIN |
| Парткод: | 4036 2549 01 |
| Деталь: | Fusing Shaft /2 |
| Парткод: | A00J 2315 00 |
| Деталь: | Gear13T |
| Парткод: | A00J 2358 00 |
| Деталь: | BUSHING |
| Парткод: | 4036 2524 01 |
| Деталь: | Fusing Frame /2 |
| Парткод: | A00J 2310 00 |
| Деталь: | GEAR 30T |
| Парткод: | A00J 2304 00 |
| Деталь: | Fusing Frame /3 |
| Парткод: | A00J 2320 11 |
| Деталь: | Fusing Knob /1 |
| Парткод: | A00J 2322 00 |
| Деталь: | Gear 35/23T |
| Парткод: | A00J 2302 00 |
| Деталь: | Pressure Shaft /1 |
| Парткод: | A00J 2354 00 |
| Деталь: | Pressure Gear /2 34/63T |
| Парткод: | A0P0 2356 01 |
| Деталь: | PRESSURE STAKE /2 |
| Парткод: | A00J 2353 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Pressure Gear /1 18/75T |
| Парткод: | A0P0 2355 00 |
| Деталь: | PRESSURE STAKE /1 |
| Парткод: | A00J 2352 00 |
| Деталь: | Pressure Frame /1 |
| Парткод: | A00J 2350 03 |
| Деталь: | MOTOR ASSY |
| Парткод: | A00J R749 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4036 2258 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4004 2248 02 |
| Деталь: | BRACKET |
| Парткод: | 4036 2241 02 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06 M601 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1380 00 |
| Деталь: | Fusing Drive Assy |
| Парткод: | A0P0 R738 00 |
| Деталь: | Slide Rail |
| Парткод: | A0P0 1250 00 |
| Деталь: | Mounting Plate /Left |
| Парткод: | A0P0 1084 00 |
| Деталь: | SPACER |
| Парткод: | A0P0 1081 00 |
| Деталь: | HOLDER |
| Парткод: | A0P0 1157 00 |
| Деталь: | LABEL |
| Парткод: | A00J 9412 01 |
| Деталь: | Rail /E |
| Парткод: | A0P0 1105 00 |
| Деталь: | SEALING PART |
| Парткод: | A0P0 1089 00 |
| Деталь: | Scatteringprevention Duct |
| Парткод: | A0P0 1086 11 |
| Деталь: | SEAL |
| Парткод: | A0P0 1253 00 |
| Деталь: | Mounting Plate /Right |
| Парткод: | A0P0 1085 00 |
| Деталь: | SCREW |
| Парткод: | A0P0 3827 00 |
| Деталь: | Ozone Seal /Black |
| Парткод: | A0P0 1141 00 |
| Деталь: | Cushion /Lower |
| Парткод: | A00J 1212 00 |
| Деталь: | SEALING PART |
| Парткод: | A0P0 1083 00 |
| Деталь: | Mounting Plate /Lower |
| Парткод: | A0P0 1082 01 |
| Деталь: | Protection Cushion |
| Парткод: | A0P0 1097 01 |
| Деталь: | Stepping motor |
| Парткод: | A02E M10A 00 |
| Деталь: | Vibrationproof Rubber |
| Парткод: | A0P0 2767 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2766 00 |
| Деталь: | TENSION SPRING |
| Парткод: | 4002 1458 01 |
| Деталь: | Belt 210L |
| Парткод: | A02E 2756 00 |
| Деталь: | Pulley 84T |
| Парткод: | A0P0 2755 00 |
| Деталь: | BUSHING |
| Парткод: | A00J 2762 00 |
| Деталь: | PULLEY |
| Парткод: | A00J 2753 00 |
| Деталь: | Wire /Rear |
| Парткод: | A00J 2752 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 2754 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 2801 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0903 01 |
| Деталь: | LEVER |
| Парткод: | A00J 2802 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4036 1720 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 2761 00 |
| Деталь: | Scanner Wiring /5 |
| Парткод: | A0P0 N145 00 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 81 |
| Деталь: | Wire /Front |
| Парткод: | A00J 2751 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 2760 00 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 2763 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 2759 01 |
| Деталь: | PULLEY |
| Парткод: | A00J 2758 00 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 2768 00 |
| Деталь: | COVER |
| Парткод: | A0P0 2785 00 |
| Деталь: | CCD Lens Assy |
| Парткод: | A0P0 R708 00 |
| Деталь: | FERRITECORE |
| Парткод: | A0P0 M900 00 |
| Деталь: | Scanner Wiring /3 |
| Парткод: | A0P0 N143 00 |
| Деталь: | TAPE |
| Парткод: | A0P0 2648 00 |
| Деталь: | Slide Rail /A |
| Парткод: | A00J 6312 02 |
| Деталь: | SCREW |
| Парткод: | A00J 6184 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6071 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A00J 6078 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6074 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6075 00 |
| Деталь: | Conveyance Roller /A |
| Парткод: | A0P0 6070 00 |
| Деталь: | Conveyance Base frame |
| Парткод: | A0P0 6060 00 |
| Деталь: | BUSHING |
| Парткод: | A0P0 6636 00 |
| Деталь: | Slide Shaft Holder |
| Парткод: | A03U 8128 00 |
| Деталь: | Label LC1 |
| Парткод: | A00J 9418 00 |
| Деталь: | COUPLING SPRING |
| Парткод: | A00J 6601 00 |
| Деталь: | CLEANER COUPLING PART |
| Парткод: | 55VA 1554 1 |
| Деталь: | Seal /B |
| Парткод: | A00J 1149 01 |
| Деталь: | Ozone Duct /B |
| Парткод: | A0P0 1136 00 |
| Деталь: | Seal /A |
| Парткод: | A00J 1144 01 |
| Деталь: | Seal /Cyan |
| Парткод: | A00J 1143 00 |
| Деталь: | ERASE ASSY |
| Парткод: | 4036 6062 02 |
| Деталь: | Positioning Holder /Cyan |
| Парткод: | A00J 1196 00 |
| Деталь: | Positioning Holder /Yellow |
| Парткод: | A00J 1195 00 |
| Деталь: | Ozone Duct |
| Парткод: | A00J 1134 00 |
| Деталь: | SEAL |
| Парткод: | A00J 1147 01 |
| Деталь: | Ozone Duct /Inside |
| Парткод: | A00J 1138 00 |
| Деталь: | Seal /Upper |
| Парткод: | A00J 1162 01 |
| Деталь: | Seal /Lower |
| Парткод: | A00J 1161 00 |
| Деталь: | Seal /Inside |
| Парткод: | A0P0 1150 00 |
| Деталь: | Ozone Duct /Front |
| Парткод: | A00J 1164 00 |
| Деталь: | Ozone Duct /Rear |
| Парткод: | A00J 1163 01 |
| Деталь: | Ozone Duct /A |
| Парткод: | A0P0 1197 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | SEAL |
| Парткод: | 4036 2485 01 |
| Деталь: | Ozone Duct /B |
| Парткод: | A0P0 1198 00 |
| Деталь: | SEAL |
| Парткод: | A00J 1165 11 |
| Деталь: | OZONE FILTER |
| Парткод: | A00J R731 00 |
| Деталь: | Duct /Cyan |
| Парткод: | A00J 1170 00 |
| Деталь: | Seal /Cyan |
| Парткод: | A00J 1148 01 |
| Деталь: | Ozone Duct /Cyan |
| Парткод: | A00J 1135 00 |
| Деталь: | Seal /B |
| Парткод: | A00J 1145 02 |
| Деталь: | SEAL |
| Парткод: | A00J 1146 03 |
| Деталь: | Conveyance Cover /Right |
| Парткод: | A00J 7051 14 |
| Деталь: | HOLDER |
| Парткод: | 4036 3597 02 |
| Деталь: | Conveyance Relay harness /1 |
| Парткод: | A00J N111 01 |
| Деталь: | COLLAR |
| Парткод: | 4036 3659 01 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 7068 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4025 3534 01 |
| Деталь: | Reinforce Plate /Front |
| Парткод: | A00J 7057 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 7058 00 |
| Деталь: | Guide Film |
| Парткод: | A00J 7052 00 |
| Деталь: | Open/close Lever /Right |
| Парткод: | A00J 7062 00 |
| Деталь: | Lock Lever /F |
| Парткод: | A00J 7065 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4036 3590 02 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J 7094 00 |
| Деталь: | LABEL HI-TEMP CAUTION |
| Парткод: | 4138 5866 01 |
| Деталь: | LABEL |
| Парткод: | A00J 9414 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 7063 00 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J 7095 00 |
| Деталь: | Holding Lever |
| Парткод: | A0P0 7053 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 7060 00 |
| Деталь: | Support Plate |
| Парткод: | A00J 7067 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 7064 00 |
| Деталь: | CONTACT |
| Парткод: | A0P0 7082 00 |
| Деталь: | ROLL |
| Парткод: | A0P0 7096 00 |
| Деталь: | RESISTOR |
| Парткод: | 9454 4076 02 |
| Деталь: | GROUND PLATE |
| Парткод: | A00J 7081 00 |
| Деталь: | CONTACT |
| Парткод: | A00J 7084 00 |
| Деталь: | CONTACT |
| Парткод: | A00J 7083 00 |
| Деталь: | CONTACT |
| Парткод: | A00J 7089 00 |
| Деталь: | CONTACT |
| Парткод: | A00J 7087 00 |
| Деталь: | CONTACT |
| Парткод: | A0P0 7091 00 |
| Деталь: | CUSHION |
| Парткод: | A00J 8157 11 |
| Деталь: | Conveyance Duct |
| Парткод: | A00J 7056 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J 7080 00 |
| Деталь: | Lock Lever /R |
| Парткод: | A00J 7066 00 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J 7093 00 |
| Деталь: | Support Shaft |
| Парткод: | A00J 7073 00 |
| Деталь: | Wiring Cover |
| Парткод: | A00J 7059 00 |
| Деталь: | CONTACT |
| Парткод: | A0P0 7122 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 7090 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1252 00 |
| Деталь: | Protection Sheet /Black |
| Парткод: | A00J 1217 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 1079 2219 01 |
| Деталь: | LABEL |
| Парткод: | A00J 9412 01 |
| Деталь: | Protection Seal |
| Парткод: | A00J 1216 00 |
| Деталь: | Developing Relay harness |
| Парткод: | A0P0 N127 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1553 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1440 00 |
| Деталь: | DUCT |
| Парткод: | A0P0 1551 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 1591 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1100 33 |
| Деталь: | MOTOR ASSY |
| Парткод: | 4037 R710 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1091 00 |
| Деталь: | COLLAR |
| Парткод: | A00J 1234 00 |
| Деталь: | GEAR 22T |
| Парткод: | A00J 1233 00 |
| Деталь: | COUPLING |
| Парткод: | A00J 1232 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1251 00 |
| Деталь: | HANDLE |
| Парткод: | A00J 8103 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4497 3106 03 |
| Деталь: | Guide Part /Front |
| Парткод: | A00J 8146 00 |
| Деталь: | Cover /Front |
| Парткод: | A00J 8104 00 |
| Деталь: | GEAR 48T |
| Парткод: | A0P0 8128 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | Mounting Plate /B |
| Парткод: | A00J R7AV 00 |
| Деталь: | Gear 22/48T |
| Парткод: | A0P0 8129 00 |
| Деталь: | Belt 248L |
| Парткод: | A00J 8130 00 |
| Деталь: | WASHER |
| Парткод: | 1200 1646 03 |
| Деталь: | ROLL |
| Парткод: | A00J 8136 00 |
| Деталь: | Torsion Spring /Lower |
| Парткод: | A00J 8124 00 |
| Деталь: | STOP RING |
| Парткод: | 0910 3620 01 |
| Деталь: | LEVER |
| Парткод: | A00J 8123 00 |
| Деталь: | Pulley 26T |
| Парткод: | A00J 8122 00 |
| Деталь: | Pulley 22T |
| Парткод: | 4657 3713 01 |
| Деталь: | Mounting Plate /D |
| Парткод: | A00J R7AW 00 |
| Деталь: | MOUNTING PLATE /C |
| Парткод: | A00J R7AX 11 |
| Деталь: | Roller /4 |
| Парткод: | A00J 8110 00 |
| Деталь: | ROLL |
| Парткод: | A00J 8141 01 |
| Деталь: | SHAFT |
| Парткод: | A00J 8144 11 |
| Деталь: | SPRING |
| Парткод: | A00J 8145 00 |
| Деталь: | BASE FRAME |
| Парткод: | A00J 8101 24 |
| Деталь: | Actuator /Upper |
| Парткод: | A00J 8118 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4657 3735 01 |
| Деталь: | Roller /1 |
| Парткод: | A00J 8108 00 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | KNOB |
| Парткод: | A00J 8151 00 |
| Деталь: | Mounting Plate /A |
| Парткод: | A00J R7AY 00 |
| Деталь: | Torsion Spring /Upper |
| Парткод: | A00J 8121 00 |
| Деталь: | Pulley 22T |
| Парткод: | A00J 8112 00 |
| Деталь: | LEVER |
| Парткод: | A00J 8152 00 |
| Деталь: | Belt 306L |
| Парткод: | A00J 8116 00 |
| Деталь: | STOPPER |
| Парткод: | A00J 8164 00 |
| Деталь: | Guide Part /Rear |
| Парткод: | A00J 8147 00 |
| Деталь: | Open/close Cover |
| Парткод: | A00J 8105 04 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 8158 01 |
| Деталь: | STAY |
| Парткод: | A0P0 1337 01 |
| Деталь: | COVER |
| Парткод: | A00J 1390 00 |
| Деталь: | COVER |
| Парткод: | A00J 1391 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0 1338 00 |
| Деталь: | ROCKER SWITCH |
| Парткод: | A00J M603 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1364 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1347 02 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J 1404 01 |
| Деталь: | LABEL |
| Парткод: | 9J06 7301 01 |
| Деталь: | COVER |
| Парткод: | A00J 1389 00 |
| Деталь: | BRACKET |
| Парткод: | 4037 2239 02 |
| Деталь: | AC Relay harness /5 |
| Парткод: | A00H N10K 00 |
| Деталь: | AC Relay harness /1 |
| Парткод: | A00J N107 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00H 1433 00 |
| Деталь: | POWER CORD |
| Парткод: | 4037 0775 01 |
| Деталь: | Power source Cord /120V |
| Парткод: | A00J N300 00 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J 1405 01 |
| Деталь: | POWER SOURCE TRANSFORMER |
| Парткод: | 56AA 8452 0 |
| Деталь: | POWER SOURCE TRANSFORMER |
| Парткод: | 56AE 8452 0 |
| Деталь: | Power Source Transfomer |
| Парткод: | 56AF 8452 1 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1408 00 |
| Деталь: | NOISE FILTER |
| Парткод: | 56QE 8826 1 |
| Деталь: | Circuit Board Spacer |
| Парткод: | V502 0100 57 |
| Деталь: | PLATE SPRING |
| Парткод: | A0P0 1488 01 |
| Деталь: | Circuit Board Spacer |
| Парткод: | V502 0100 56 |
| Деталь: | PWB Assembly RL |
| Парткод: | A00J H004 00 |
| Деталь: | PWB Assembly (PWB-KH ASSY) |
| Парткод: | A0P0 H002 00 |
| Деталь: | SUPPORT |
| Парткод: | V502 0100 26 |
| Деталь: | COVER |
| Парткод: | A00J 1379 00 |
| Деталь: | Control Relay harness /1 |
| Парткод: | A0P0 N12E 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1363 02 |
| Деталь: | Paperfeed Control harness |
| Парткод: | A0P0 N103 00 |
| Деталь: | Relay |
| Парткод: | A00H M600 00 |
| Деталь: | Support Holder |
| Парткод: | A00J 5950 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 5905 00 |
| Деталь: | Guide Plate /Front |
| Парткод: | A0P0 5875 00 |
| Деталь: | Guide Sheet |
| Парткод: | A00J 5862 01 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | SHAFT |
| Парткод: | 4030 3003 01 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | CLUTCH |
| Парткод: | A00J 5956 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | Paper feed Holder |
| Парткод: | A0P0 5901 00 |
| Деталь: | GEAR 30T |
| Парткод: | 4425 3013 01 |
| Деталь: | GEAR 20T |
| Парткод: | A00J 5903 00 |
| Деталь: | SHAFT |
| Парткод: | 4040 3097 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5904 00 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | Paper feed Shaft |
| Парткод: | A00J 5907 00 |
| Деталь: | Paper feed Coupling |
| Парткод: | A00J 5870 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5861 00 |
| Деталь: | Paper feed Shaft |
| Парткод: | A00J 5860 00 |
| Деталь: | FRAME /BYPASS (REAR) |
| Парткод: | A00J R7AQ 00 |
| Деталь: | Pressing Collar |
| Парткод: | A00J 5967 00 |
| Деталь: | Gear 15/28T |
| Парткод: | A00J 5958 00 |
| Деталь: | GEAR 14T |
| Парткод: | A00J 5926 00 |
| Деталь: | Gear 18/29T |
| Парткод: | A00J 5922 01 |
| Деталь: | Gear 18/35T |
| Парткод: | A00J 5917 00 |
| Деталь: | GEAR 26T |
| Парткод: | A00J 5928 00 |
| Деталь: | Compressing Coil |
| Парткод: | A00J 5930 00 |
| Деталь: | Wiring Cover |
| Парткод: | A00J 5960 00 |
| Деталь: | ROLL |
| Парткод: | 9J07 3008 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A108 8905 00 |
| Деталь: | ARM |
| Парткод: | 9J07 3017 02 |
| Деталь: | BRACKET |
| Парткод: | 9J07 3020 01 |
| Деталь: | SHAFT |
| Парткод: | 9J07 3019 02 |
| Деталь: | Holder /Front |
| Парткод: | A0HT 5616 00 |
| Деталь: | BRACKET |
| Парткод: | 9J07 3031 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 9J07 3016 01 |
| Деталь: | BRACKETASSY |
| Парткод: | 9J07 R710 00 |
| Деталь: | BRACKET |
| Парткод: | 9J07 3318 01 |
| Деталь: | GUIDE |
| Парткод: | A108 5615 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | A108 8913 00 |
| Деталь: | Separator Pad Assy |
| Парткод: | A01H R704 00 |
| Деталь: | BRACKET |
| Парткод: | A01H 5655 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | A01H 5651 00 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A0HT 5611 00 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | SHAFT |
| Парткод: | A0HT 5612 02 |
| Деталь: | ROLLER |
| Парткод: | A108 5639 00 |
| Деталь: | HOLDER |
| Парткод: | 9J07 3404 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A01H 5654 00 |
| Деталь: | SHAFT |
| Парткод: | 9J07 3408 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07 3405 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A108 1007 01 |
| Деталь: | GUIDE |
| Парткод: | A108 1012 00 |
| Деталь: | COVER |
| Парткод: | A108 5614 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0HT 8914 00 |
| Деталь: | Holder /Rear |
| Парткод: | A0HT 5617 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A108 5702 00 |
| Деталь: | HOLDER |
| Парткод: | A0HT 5628 00 |
| Деталь: | Fusing Unit 100V |
| Парткод: | A0P0 R732 11 |
| Деталь: | FUSING UNIT 120V |
| Парткод: | A0P0 R733 11 |
| Деталь: | FUSING UNIT 200V |
| Парткод: | A0P0 R734 11 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0 1385 00 |
| Деталь: | AC Relay harness |
| Парткод: | A0P0 N108 00 |
| Деталь: | Fixing Coil |
| Парткод: | A0P0 M402 02 |
| Деталь: | Fixing Coil |
| Парткод: | A0P0 M403 02 |
| Деталь: | Fixing Coil |
| Парткод: | A0P1 M402 02 |
| Деталь: | COVER |
| Парткод: | A0P0 1324 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1369 11 |
| Деталь: | FAN MOTOR |
| Парткод: | 4556 M100 00 |
| Деталь: | SEAL |
| Парткод: | A00J 1430 00 |
| Деталь: | Dust-proof Filter |
| Парткод: | A00J 1412 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 1436 00 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J 1435 00 |
| Деталь: | Main power assy 100V |
| Парткод: | A0P0 R704 11 |
| Деталь: | Main power assy 200V |
| Парткод: | A0P0 R705 11 |
| Деталь: | Mounting Plate /A |
| Парткод: | A00J 6140 02 |
| Деталь: | Support Shaft /B |
| Парткод: | A00J 6145 01 |
| Деталь: | Swing Shaft /B |
| Парткод: | A00J 6147 00 |
| Деталь: | Sensor Block |
| Парткод: | A00J 6143 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | PAPER DETECTION ACTUATOR |
| Парткод: | 56QA 5724 0 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 56QA 5717 0 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6148 00 |
| Деталь: | Swing Panel /B |
| Парткод: | A00J 6142 00 |
| Деталь: | SCREW |
| Парткод: | 4036 5966 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 6064 00 |
| Деталь: | Idler Shaft |
| Парткод: | A00J 6065 00 |
| Деталь: | ROLL |
| Парткод: | 4030 3122 01 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 6066 00 |
| Деталь: | Conveyance Cover |
| Парткод: | A0P0 6062 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 6061 00 |
| Деталь: | SUPPORT BLOCK |
| Парткод: | 56QA 5711 0 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6068 02 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 6069 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 6067 00 |
| Деталь: | LOCK SPRING |
| Парткод: | A00J 6602 00 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A00J 6073 01 |
| Деталь: | Light blocking Sheet |
| Парткод: | A0P0 6634 00 |
| Деталь: | Shaft /L |
| Парткод: | A00J 6226 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 6233 00 |
| Деталь: | ROLL |
| Парткод: | A00J 6630 00 |
| Деталь: | TRAY PRESSING PLATE |
| Парткод: | 56AA 4171 1 |
| Деталь: | Label LC2 |
| Парткод: | A00J 9419 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A00J 6076 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A00J 6077 00 |
| Деталь: | Swing Panel /ASSY |
| Парткод: | A00J 6141 01 |
| Деталь: | SWING SPRING REAR |
| Парткод: | 56QA 5721 0 |
| Деталь: | Swing Shaft /A |
| Парткод: | A00J 6146 00 |
| Деталь: | Support Shaft /A |
| Парткод: | A00J 6144 00 |
| Деталь: | PFU Relay harness /6 |
| Парткод: | A00J N11F 01 |
| Деталь: | REINFORCE PLATE /1 |
| Парткод: | A00J 5619 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0902 01 |
| Деталь: | BRACKET |
| Парткод: | 4348 3049 01 |
| Деталь: | Conveyance Roller /1 |
| Парткод: | A0P0 5707 01 |
| Деталь: | BALL BEARING |
| Парткод: | A00V 2406 00 |
| Деталь: | HOLDING GUIDE |
| Парткод: | A0P0 5676 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 5605 02 |
| Деталь: | Paperfeed Relay harness /3 |
| Парткод: | A00J N118 03 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 5743 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3125 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J 5613 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5612 00 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A0P0 5617 00 |
| Деталь: | Mounting Plate /S |
| Парткод: | A00J 5646 00 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | Holder /S |
| Парткод: | A00J 5647 00 |
| Деталь: | Guide Roller /Rear |
| Парткод: | A00J 5748 00 |
| Деталь: | Fieldroller assy |
| Парткод: | A0P0 R740 00 |
| Деталь: | Release Lever |
| Парткод: | A0P0 5681 00 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 5672 11 |
| Деталь: | Conveyance Gear /3 28T |
| Парткод: | A00J 5654 00 |
| Деталь: | Conveyance Gear /2 21/31T |
| Парткод: | A00J 5653 00 |
| Деталь: | GEAR 24T |
| Парткод: | A0P0 5704 00 |
| Деталь: | Conveyance Belt 74L |
| Парткод: | A0P0 5680 00 |
| Деталь: | Frame/Drive Moter |
| Парткод: | A0P0 R7A1 00 |
| Деталь: | Stepping motor |
| Парткод: | A0P0 M125 00 |
| Деталь: | Drive Holder /1 |
| Парткод: | A00J 5633 00 |
| Деталь: | Conveyance Gear /4 20/31T |
| Парткод: | A00J 5655 00 |
| Деталь: | GEAR 22T |
| Парткод: | A00J 5744 00 |
| Деталь: | Wiring Cover /1 |
| Парткод: | A00J 5634 00 |
| Деталь: | Positioning Plate /Rear |
| Парткод: | A00J 5987 00 |
| Деталь: | Fieldroller assy |
| Парткод: | A0P0 R739 00 |
| Деталь: | Mounting Plate /B |
| Парткод: | A00J 6314 02 |
| Деталь: | Guide Film |
| Парткод: | A00J 6213 01 |
| Деталь: | Mounting Plate /A |
| Парткод: | A00J 6313 01 |
| Деталь: | COVER CASSETTE |
| Парткод: | A00J 1607 02 |
| Деталь: | LEVER |
| Парткод: | A00J 6214 00 |
| Деталь: | Label Cd |
| Парткод: | A00J 9421 02 |
| Деталь: | Label FD |
| Парткод: | A00J 9422 02 |
| Деталь: | Label FD |
| Парткод: | A00J 9423 02 |
| Деталь: | ROLL |
| Парткод: | A00J 6630 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 6233 00 |
| Деталь: | TRAY PRESSING PLATE |
| Парткод: | 56AA 4171 1 |
| Деталь: | Mounting Plate /L |
| Парткод: | A00J 6223 00 |
| Деталь: | Shaft /L |
| Парткод: | A00J 6226 00 |
| Деталь: | TRAY POSITIONING SPRING |
| Парткод: | 56QA 1123 0 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 6229 00 |
| Деталь: | GUIDE |
| Парткод: | 4030 3228 12 |
| Деталь: | STOPPER |
| Парткод: | A00J 6311 00 |
| Деталь: | Guide Sheet |
| Парткод: | A00J 6305 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6310 02 |
| Деталь: | GUIDE SHEET/2 |
| Парткод: | A00J 6319 00 |
| Деталь: | Mounting Plate /L |
| Парткод: | A00J 6315 00 |
| Деталь: | EARTH GROUND |
| Парткод: | 4030 3223 03 |
| Деталь: | Pulling Spring |
| Парткод: | A0P0 6238 00 |
| Деталь: | REGULATING PLATE R ASSY |
| Парткод: | A00J R743 00 |
| Деталь: | PWB Assembly(PWB-IF ASSY) |
| Парткод: | A1DM H01C 00 |
| Деталь: | Inverter unit |
| Парткод: | A00J M410 00 |
| Деталь: | SPACER |
| Парткод: | V502 0100 33 |
| Деталь: | SPACER |
| Парткод: | V502 0100 36 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2811 00 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 2812 00 |
| Деталь: | GUIDE PART |
| Парткод: | A0P0 2813 00 |
| Деталь: | PWB assembly(PWB-UCN ASSY) |
| Парткод: | A0P0 H025 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1480 00 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A0P0 1481 01 |
| Деталь: | Mounting Plate /2 |
| Парткод: | A0P0 1482 01 |
| Деталь: | 1st Slider Assy |
| Парткод: | A0P0 R711 00 |
| Деталь: | TAPE |
| Парткод: | A0P0 2648 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1500 21 |
| Деталь: | Scanner Wiring /1 |
| Парткод: | A1DM N147 00 |
| Деталь: | Scanner Wiring /2 |
| Парткод: | A0P0 N142 00 |
| Деталь: | CABLE |
| Парткод: | A0P0 N153 00 |
| Деталь: | Grounding Wire /1 |
| Парткод: | A1DM N135 00 |
| Деталь: | FERRITECORE |
| Парткод: | A0P0 M900 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6199 01 |
| Деталь: | INTERNAL HEATER |
| Парткод: | 56AA 8306 1D |
| Деталь: | SCREW |
| Парткод: | A00J 6184 00 |
| Деталь: | Slide Rail /A |
| Парткод: | A00J 6134 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6084 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6086 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6081 00 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A00J 6080 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6085 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6082 00 |
| Деталь: | Shaft /L |
| Парткод: | A00J 6176 00 |
| Деталь: | TRAY POSITIONING SPRING |
| Парткод: | 56QA 1123 0 |
| Деталь: | TRAY PRESSING PLATE |
| Парткод: | 56AA 4171 1 |
| Деталь: | ROLL |
| Парткод: | A00J 6630 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 6233 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6083 00 |
| Деталь: | Conveyance Duct |
| Парткод: | A00J 7015 00 |
| Деталь: | SEAL |
| Парткод: | A00J 7091 00 |
| Деталь: | Suction Seal |
| Парткод: | A00J 7018 00 |
| Деталь: | COVER |
| Парткод: | A00J 7017 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 7024 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 1164 3527 02 |
| Деталь: | ACTUATOR |
| Парткод: | 1164 3504 03 |
| Деталь: | CONTACT |
| Парткод: | A0P0 7088 00 |
| Деталь: | Lever /1 |
| Парткод: | A00J 7113 01 |
| Деталь: | HOLD PLATE |
| Парткод: | A00J 7115 00 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 7117 00 |
| Деталь: | LEVER |
| Парткод: | 4036 3675 02 |
| Деталь: | BALL BEARING |
| Парткод: | A00V 2406 00 |
| Деталь: | GEAR 20T |
| Парткод: | A00J 7006 00 |
| Деталь: | GEAR 14T |
| Парткод: | A00J 7027 00 |
| Деталь: | BUSHING |
| Парткод: | 4025 3572 01 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 7010 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Ground Contact |
| Парткод: | A00J 7019 00 |
| Деталь: | Guide Film |
| Парткод: | A00J 7047 00 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 7078 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A00J R901 00 |
| Деталь: | Guide Film |
| Парткод: | A00J 7046 00 |
| Деталь: | Guide Film |
| Парткод: | A00J 7042 00 |
| Деталь: | Neutralizing Holder |
| Парткод: | A00J 7016 00 |
| Деталь: | NETURALIZING MEMBER |
| Парткод: | 4025 3568 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 7012 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 7001 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 7002 01 |
| Деталь: | BUSHING |
| Парткод: | 1164 3509 01 |
| Деталь: | MOUNTING PLATE / PAPER EXIT CONVEYANCE |
| Парткод: | A00J R7AT 00 |
| Деталь: | Gear 34/17T |
| Парткод: | A00J 7005 01 |
| Деталь: | Rotation Knob |
| Парткод: | A00J 7069 00 |
| Деталь: | Positioning Holder |
| Парткод: | A00J 7030 00 |
| Деталь: | GEAR 26T |
| Парткод: | A00J 7003 01 |
| Деталь: | COLLAR |
| Парткод: | A00J 7009 00 |
| Деталь: | Stepping motor |
| Парткод: | A0P0 M123 00 |
| Деталь: | Wiring Cover |
| Парткод: | A00J 7020 00 |
| Деталь: | paper exit conveyance assy |
| Парткод: | A0P0 R730 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0 1304 14 |
| Деталь: | Insulating sheet |
| Парткод: | A00J 2113 00 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J 1410 00 |
| Деталь: | FILTER |
| Парткод: | A0P0 1476 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1496 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1394 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 1406 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1331 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4004 6854 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1335 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1497 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1483 00 |
| Деталь: | Cover /ASSY |
| Парткод: | A0P0 1329 01 |
| Деталь: | PWB Assenbly (PWB-MC ASSY) |
| Парткод: | A0P0 H001 01 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0 1336 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A0P0 1388 11 |
| Деталь: | Heat sink Part |
| Парткод: | A0P0 1454 00 |
| Деталь: | SCREW |
| Парткод: | 4036 5966 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | DUCT |
| Парткод: | A00J 1561 02 |
| Деталь: | GROUND PLATE |
| Парткод: | A0P0 1464 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1462 00 |
| Деталь: | GASKET |
| Парткод: | A0P0 M901 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0P0 1460 00 |
| Деталь: | GASKET |
| Парткод: | A1DM M900 00 |
| Деталь: | Manuscript glass assy |
| Парткод: | A0P0 R710 00 |
| Деталь: | Holding Plate spring |
| Парткод: | A0P0 2736 00 |
| Деталь: | MIRROR |
| Парткод: | A0P0 2732 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2734 00 |
| Деталь: | COVER |
| Парткод: | A00J 2743 00 |
| Деталь: | SCREW |
| Парткод: | A00J 2744 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A0P0 2735 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2733 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 2742 01 |
| Деталь: | PULLEY |
| Парткод: | A00J 2739 00 |
| Деталь: | BUSHING |
| Парткод: | 4002 1481 01 |
| Деталь: | BUSHING |
| Парткод: | 4002 1480 02 |
| Деталь: | Holding Plate spring |
| Парткод: | A0P0 2737 00 |
| Деталь: | FRAME |
| Парткод: | A00J 2731 03 |
| Деталь: | Holding Plate spring |
| Парткод: | A0P0 2738 00 |
| Деталь: | Holding Plate |
| Парткод: | A00J 2651 00 |
| Деталь: | PULLEY |
| Парткод: | A00J 2740 00 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 2741 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A00J 2653 00 |
| Деталь: | Holding Plate |
| Парткод: | A00J 2652 00 |
| Деталь: | SEAL |
| Парткод: | A00J 2658 00 |
| Деталь: | SEAL |
| Парткод: | 9J06 1620 01 |
| Деталь: | SEAL |
| Парткод: | A00J 2655 00 |
| Деталь: | SEAL |
| Парткод: | A00J 2654 00 |
| Деталь: | Holding Plate |
| Парткод: | A00J 5233 12 |
| Деталь: | PLATE / REAR |
| Парткод: | A00J R7A2 00 |
| Деталь: | Sensor Relay harness /4 |
| Парткод: | A0P0 N12M 00 |
| Деталь: | LOCK PLATE / REAR |
| Парткод: | A00J R7A3 00 |
| Деталь: | Connecting Plate |
| Парткод: | A00J 5232 01 |
| Деталь: | Transfer Wiring |
| Парткод: | A00J N13C 00 |
| Деталь: | Separating Wiring /E |
| Парткод: | A00J N13D 00 |
| Деталь: | SLIDE PLATE / REAR |
| Парткод: | A00J R7BB 00 |
| Деталь: | Cover /4 |
| Парткод: | A00J 5244 02 |
| Деталь: | PIN |
| Парткод: | 4036 2311 01 |
| Деталь: | Contact /Black |
| Парткод: | A00J 5203 00 |
| Деталь: | Contact /Cyan |
| Парткод: | A00J 5227 00 |
| Деталь: | Contact /Black |
| Парткод: | A00J 5226 00 |
| Деталь: | Cover /1 |
| Парткод: | A00J 5241 01 |
| Деталь: | SENSOR RELAY HARNESS/8 |
| Парткод: | A00J N10M 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A00J R900 00 |
| Деталь: | Cover /2 |
| Парткод: | A00J 5242 01 |
| Деталь: | Transfer Rail /Front |
| Парткод: | A00J 5201 02 |
| Деталь: | Plate spring /1 |
| Парткод: | A00J 5216 01 |
| Деталь: | LOCK PLATE / FRONT |
| Парткод: | A00J R7A5 00 |
| Деталь: | Holding Plate |
| Парткод: | A00J 5240 01 |
| Деталь: | PLATE / FRONT |
| Парткод: | A00J R7A6 00 |
| Деталь: | Connecting Plate |
| Парткод: | A00J 5239 01 |
| Деталь: | SLIDE PLATE / FRONT |
| Парткод: | A00J R7A7 00 |
| Деталь: | Plate spring /2 |
| Парткод: | A00J 5217 01 |
| Деталь: | Contact /Cyan |
| Парткод: | A00J 5204 00 |
| Деталь: | Contact /Yellow |
| Парткод: | A00J 5206 00 |
| Деталь: | Transfer Rail /Rear |
| Парткод: | A00J 5202 03 |
| Деталь: | Guide Seal /2 |
| Парткод: | A0P0 1095 01 |
| Деталь: | CONTACT |
| Парткод: | A00J 5208 00 |
| Деталь: | CONTACT |
| Парткод: | A00J 5209 00 |
| Деталь: | SEPARATING WIRING/1 |
| Парткод: | A00J N13E 00 |
| Деталь: | SEPARATING WIRING/2 |
| Парткод: | A00J N13F 00 |
| Деталь: | Cover /3 |
| Парткод: | A00J 5243 00 |
| Деталь: | Contact /Magenta |
| Парткод: | A00J 5205 00 |
| Деталь: | RAIL |
| Парткод: | A0P0 1333 01 |
| Деталь: | PWB assembly(PWB-PCI ASSY) |
| Парткод: | A0P0 H026 01 |
| Деталь: | RAIL |
| Парткод: | A0P0 1445 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1479 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1366 11 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1492 00 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A0P0 1441 00 |
| Деталь: | BUSHING |
| Парткод: | A0P0 1444 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0 1443 00 |
| Деталь: | HDD |
| Парткод: | A0P0 M720 00 |
| Деталь: | CABLE |
| Парткод: | A0P0 N152 00 |
| Деталь: | CABLE |
| Парткод: | A0P0 N151 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1442 00 |
| Деталь: | CONTACT |
| Парткод: | A0P0 1593 00 |
| Деталь: | CONTACT |
| Парткод: | A0P0 1592 00 |
| Деталь: | FAN MOTOR |
| Парткод: | A0ED M105 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1448 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1328 01 |
| Деталь: | RAIL |
| Парткод: | A0P0 1477 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A0P0 1493 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0P0 1463 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 5751 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3081 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030 3224 02 |
| Деталь: | HOLDER |
| Парткод: | 4030 3083 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | LEVER |
| Парткод: | 4030 3091 01 |
| Деталь: | PWB ASSY |
| Парткод: | 4037 0104 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5753 02 |
| Деталь: | Rail /Left |
| Парткод: | A00J 1332 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1386 00 |
| Деталь: | Paperfeed Relay Harness /1 |
| Парткод: | A00J N116 01 |
| Деталь: | Paperfeed Relay harness /2 |
| Парткод: | A00J N117 02 |
| Деталь: | HOLDER |
| Парткод: | 4011 3012 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4002 3131 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4002 3110 01 |
| Деталь: | MOTOR |
| Парткод: | 9J06 M103 00 |
| Деталь: | HOLDER |
| Парткод: | 4030 3047 02 |
| Деталь: | Cover Upper |
| Парткод: | A0HT 5608 11 |
| Деталь: | Label Size |
| Парткод: | A0HT 9405 00 |
| Деталь: | LABEL |
| Парткод: | A108 9401 00 |
| Деталь: | Light blocking Part |
| Парткод: | A0HT 5622 00 |
| Деталь: | ARM |
| Парткод: | A07H 5703 00 |
| Деталь: | ROLLER |
| Парткод: | 9J07 3301 01 |
| Деталь: | Pulley 21T |
| Парткод: | 9J07 3308 01 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | SHAFT |
| Парткод: | 9J07 3302 01 |
| Деталь: | ARM |
| Парткод: | A07H 5701 00 |
| Деталь: | STOPPER RING |
| Парткод: | 1033 4402 03 |
| Деталь: | BUSHING |
| Парткод: | 4469 3465 01 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | GUIDE |
| Парткод: | A07H 5700 01 |
| Деталь: | GUIDE |
| Парткод: | 9J07 3321 02 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N107 00 |
| Деталь: | Photoreflector |
| Парткод: | A03T M500 00 |
| Деталь: | BRACKET |
| Парткод: | A07H 5702 00 |
| Деталь: | BRACKET |
| Парткод: | A07H 5708 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | A01H 5651 00 |
| Деталь: | BRACKET |
| Парткод: | A07H 5706 00 |
| Деталь: | TENSION SPRING |
| Парткод: | A07H 5704 00 |
| Деталь: | CLUTCH |
| Парткод: | A07H 5705 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | SHAFT |
| Парткод: | 9J07 3303 01 |
| Деталь: | TIMING BELT 122L |
| Парткод: | 4641 3514 01 |
| Деталь: | Gear16T |
| Парткод: | A108 2134 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 2537 01 |
| Деталь: | Gear /2 16T |
| Парткод: | A108 5613 00 |
| Деталь: | WASHER |
| Парткод: | A108 2138 00 |
| Деталь: | SHAFT |
| Парткод: | A108 2130 01 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A108 2137 00 |
| Деталь: | CLUTCH |
| Парткод: | A108 M200 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 2133 01 |
| Деталь: | Pulley 19T |
| Парткод: | 9J07 3319 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4643 3007 01 |
| Деталь: | BUSHING |
| Парткод: | A108 2607 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | A108 2727 00 |
| Деталь: | ROLL |
| Парткод: | 9J07 8103 00 |
| Деталь: | SHAFT |
| Парткод: | A108 2666 00 |
| Деталь: | SHAFT |
| Парткод: | A108 2617 01 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A108 2645 00 |
| Деталь: | GUIDE |
| Парткод: | A108 2668 00 |
| Деталь: | Torsion Spring /Front |
| Парткод: | A108 2696 00 |
| Деталь: | Lock Part /Front |
| Парткод: | A108 2605 01 |
| Деталь: | LOCK LEVER |
| Парткод: | A108 2663 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 2711 01 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A108 2720 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A108 2724 01 |
| Деталь: | ROLL |
| Парткод: | 9J07 4302 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A108 2721 01 |
| Деталь: | GUIDE |
| Парткод: | 9J07 4415 02 |
| Деталь: | GUIDE PLATE |
| Парткод: | A108 2722 00 |
| Деталь: | SHAFT |
| Парткод: | A108 2725 00 |
| Деталь: | Torsion Spring /Rear |
| Парткод: | A108 2697 00 |
| Деталь: | Lock Part /Rear |
| Парткод: | A108 2602 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 2603 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A108 2723 00 |
| Деталь: | Pen |
| Парткод: | A0PD 1602 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M705 03 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M706 03 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0 M707 03 |
| Деталь: | COVER PANEL LOWER |
| Парткод: | A0P0 1694 00 |
| Деталь: | 2ND TRANSFER ROLLER ASSY |
| Парткод: | A0P0 R719 00 |
| Деталь: | TRANSFER UNIT |
| Парткод: | A0P0 R700 33 |
| Деталь: | Reading Motor |
| Парткод: | A108 M100 00 |
| Деталь: | PULLEY |
| Парткод: | A108 2108 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 2100 00 |
| Деталь: | TIMING BELT |
| Парткод: | A108 2101 00 |
| Деталь: | FLANGE |
| Парткод: | A0HT 2107 00 |
| Деталь: | BALL BEARING |
| Парткод: | 4131 2626 01 |
| Деталь: | ROLL |
| Парткод: | 9J07 5019 01 |
| Деталь: | Tension Plate A |
| Парткод: | A108 R7A0 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A108 2104 00 |
| Деталь: | FLANGE |
| Парткод: | A0DA 7018 00 |
| Деталь: | Guide Sheet |
| Парткод: | A108 2699 00 |
| Деталь: | ROLLER |
| Парткод: | A108 7002 00 |
| Деталь: | Guide Sheet /C |
| Парткод: | A108 2625 01 |
| Деталь: | ROLLER |
| Парткод: | A0HT 7004 00 |
| Деталь: | GUIDE |
| Парткод: | A108 2692 00 |
| Деталь: | TIMING BELT |
| Парткод: | A0HU 2506 00 |
| Деталь: | BUSHING |
| Парткод: | 4658 3517 01 |
| Деталь: | Pulley 27/27T |
| Парткод: | A108 2510 00 |
| Деталь: | PULLEY GUIDE PART |
| Парткод: | 56QA 5842 0 |
| Деталь: | LABEL |
| Парткод: | A00J 9417 00 |
| Деталь: | PFU Relay harness /8 |
| Парткод: | A00J N11N 01 |
| Деталь: | WIRE PULLEY |
| Парткод: | 57AA 1701 0 |
| Деталь: | LCT GUIDE PLATE RIGHT |
| Парткод: | 56QA 5806 0D |
| Деталь: | WIRE HOLDER A |
| Парткод: | 55VA 4061 0 |
| Деталь: | PAPER REGULATING CLAW |
| Парткод: | 5400 4720 0 |
| Деталь: | Protection Cover |
| Парткод: | 56QA 5845 0 |
| Деталь: | LCT ADJUSTMENT SIDE PLATE |
| Парткод: | 56QA 5805 0D |
| Деталь: | SUPPORT BOARD / WIRE PULLEY |
| Парткод: | A00J R7AN 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6131 01 |
| Деталь: | PAPER GUIDE LABEL |
| Парткод: | 57AA 9787 0 |
| Деталь: | SHAFT HOLDING PART |
| Парткод: | 56QA 5807 0D |
| Деталь: | REAR REINFORCE PLATE |
| Парткод: | 56QA 5849 0D |
| Деталь: | PAPER GUIDE SHAFT RIGHT |
| Парткод: | 56QA 5815 0 |
| Деталь: | LABEL |
| Парткод: | A00J 9416 00 |
| Деталь: | LCT GUIDE PLATE LEFT |
| Парткод: | 56QA 5906 0D |
| Деталь: | PAPER GUIDE SHAFT LEFT |
| Парткод: | 56QA 5915 0D |
| Деталь: | Reinforce Plate /Rear |
| Парткод: | A00J 6139 00 |
| Деталь: | Conveyance Cover |
| Парткод: | A00J 6187 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | Idler Roll |
| Парткод: | A00J 6051 00 |
| Деталь: | Idler Shaft |
| Парткод: | A00J 6052 00 |
| Деталь: | SPRING MOUNTING PLATE 1 |
| Парткод: | 56AA 4043 0 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 6048 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6013 00 |
| Деталь: | BUSHING |
| Парткод: | A00J 6632 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J 6015 01 |
| Деталь: | Guide Plate /2 |
| Парткод: | A00J 6186 01 |
| Деталь: | SHAFT |
| Парткод: | A00J 6017 00 |
| Деталь: | WASHER |
| Парткод: | A00J 6029 00 |
| Деталь: | Pulley 14T |
| Парткод: | A00J 6196 00 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A00J 6185 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | Pulley 15T |
| Парткод: | A00J 6195 00 |
| Деталь: | Timing Belt 96L |
| Парткод: | A00J 6198 00 |
| Деталь: | ROLL /1 |
| Парткод: | A00J 6197 00 |
| Деталь: | ENTRANCE GUIDE SHEET |
| Парткод: | 56AA 4054 0 |
| Деталь: | Multi-feed Adjusting Plate |
| Парткод: | A00J 6016 00 |
| Деталь: | Input Shaft |
| Парткод: | A00J 6014 02 |
| Деталь: | PAPER FEED INPUT SHAFT |
| Парткод: | 56QA 4024 0D |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6036 00 |
| Деталь: | Pressing Spring |
| Парткод: | 56AA 4051 0 |
| Деталь: | PAPER FEED COUPLING PART |
| Парткод: | 56AA 4045 0 |
| Деталь: | CLEANER SHAFT HOLDER |
| Парткод: | 56AA 7505 0 |
| Деталь: | Gear 22/14T |
| Парткод: | A00J 6034 00 |
| Деталь: | Gear43T |
| Парткод: | A00J 6009 00 |
| Деталь: | Ground Plate /1 |
| Парткод: | A00J 6056 00 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 6047 01 |
| Деталь: | DOUBLE FEED PREVENTIVE PLATE |
| Парткод: | 55VA 4093 0 |
| Деталь: | Up/down Plate |
| Парткод: | A00J 6135 00 |
| Деталь: | FRICTION PLATE |
| Парткод: | A00J 6234 00 |
| Деталь: | LCT UP DOWN WIRE LEFT FRONT |
| Парткод: | 56QA 5911 0 |
| Деталь: | PAD |
| Парткод: | A0P0 6639 00 |
| Деталь: | Stopper Plate /2 |
| Парткод: | A0P0 6152 00 |
| Деталь: | Light blocking Part |
| Парткод: | A00J 6603 00 |
| Деталь: | BUSHING |
| Парткод: | A00J 6632 00 |
| Деталь: | Up/down Pulley |
| Парткод: | A00J 6137 00 |
| Деталь: | Regulating Plate /1 |
| Парткод: | A0P0 6189 00 |
| Деталь: | Gear /1 |
| Парткод: | A0P0 6638 00 |
| Деталь: | Dumper |
| Парткод: | A0P0 6627 00 |
| Деталь: | Protection Cover |
| Парткод: | A00J 6190 11 |
| Деталь: | LCT SLIDE BOARD |
| Парткод: | 56QA 5804 1D |
| Деталь: | Sensor Cover |
| Парткод: | A00J 6133 00 |
| Деталь: | Protection Sheet |
| Парткод: | A00J 6606 00 |
| Деталь: | STOPPER RUBBER |
| Парткод: | A00J 6631 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | REGISTRATION UNIT FIXED SCREW |
| Парткод: | 26NA 4544 0 |
| Деталь: | Connecting Plate |
| Парткод: | A00J 6150 00 |
| Деталь: | Protection Sheet |
| Парткод: | A00J 6605 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 6132 00 |
| Деталь: | PFU RELAY HARNESS/1 |
| Парткод: | A00J N11A 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0P0 6157 00 |
| Деталь: | Up/down Shaft |
| Парткод: | A00J 6155 00 |
| Деталь: | LCT UP DOWN WIRE LEFT REAR |
| Парткод: | 56QA 5912 0 |
| Деталь: | 1500-sheet tray M |
| Парткод: | A0P0 R727 00 |
| Деталь: | 1500-sheet tray I |
| Парткод: | A0P0 R728 00 |
| Деталь: | SEAL |
| Парткод: | 9J07 1603 02 |
| Деталь: | Mounting Plate Stake |
| Парткод: | A108 R7A2 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A108 7017 02 |
| Деталь: | Idler Roll |
| Парткод: | A108 7030 00 |
| Деталь: | LEVER |
| Парткод: | A108 7010 01 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A108 7034 00 |
| Деталь: | BRACKET ASSY |
| Парткод: | 9J07 R709 00 |
| Деталь: | GUIDE |
| Парткод: | A07H 7504 00 |
| Деталь: | GUIDE |
| Парткод: | A0HT 7008 00 |
| Деталь: | GUIDE |
| Парткод: | A0HT 7009 00 |
| Деталь: | GUIDE |
| Парткод: | A0HT 7010 00 |
| Деталь: | GUIDE |
| Парткод: | A0HT 7013 00 |
| Деталь: | SHIELD PLATE |
| Парткод: | 9J07 4116 01 |
| Деталь: | GUIDE |
| Парткод: | A07H 7505 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 9J07 4004 01 |
| Деталь: | Registration Shaft |
| Парткод: | A108 7033 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0HT 7042 00 |
| Деталь: | BRACKET |
| Парткод: | 9J07 4006 01 |
| Деталь: | GROUND PLATE |
| Парткод: | A108 7012 00 |
| Деталь: | Conveyance Shaft |
| Парткод: | A108 7032 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A0HT 7041 00 |
| Деталь: | LEFT COVER ASSY |
| Парткод: | A108 R701 00 |
| Деталь: | GUIDE |
| Парткод: | A108 7037 00 |
| Деталь: | GUIDE |
| Парткод: | A108 7038 00 |
| Деталь: | Holding Sheet |
| Парткод: | A108 7044 00 |
| Деталь: | Protection Cover |
| Парткод: | A0P0 1413 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0 1315 00 |
| Деталь: | SPACER |
| Парткод: | V502 0100 36 |
| Деталь: | Guide Cover |
| Парткод: | A0P0 1357 00 |
| Деталь: | Power source |
| Парткод: | A0P0 M400 02 |
| Деталь: | Power source |
| Парткод: | A0P0 M401 02 |
| Деталь: | Power source |
| Парткод: | A0P1 M400 02 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1325 00 |
| Деталь: | FAN MOTOR |
| Парткод: | A00J M141 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1313 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1490 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 1489 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1384 00 |
| Деталь: | Protection Seal |
| Парткод: | A0P0 1498 00 |
| Деталь: | Cover Holder |
| Парткод: | A0P0 1343 00 |
| Деталь: | Bypass Tray /3 |
| Парткод: | A0P0 5942 00 |
| Деталь: | LABEL |
| Парткод: | A00J 9425 00 |
| Деталь: | SHAFT |
| Парткод: | 1134 3042 02 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5991 00 |
| Деталь: | ACTUATOR |
| Парткод: | A00J 5853 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5979 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5977 00 |
| Деталь: | ACTUATOR |
| Парткод: | A00J 5978 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5990 00 |
| Деталь: | COLLAR |
| Парткод: | 1134 3041 01 |
| Деталь: | Bypass Tray /4 |
| Парткод: | A0P0 5943 00 |
| Деталь: | RESISTOR |
| Парткод: | V801 3000 06 |
| Деталь: | GEAR 40T |
| Парткод: | A00J 5972 01 |
| Деталь: | Rack /L |
| Парткод: | A00J 5971 00 |
| Деталь: | Gear18T |
| Парткод: | A00J 5969 00 |
| Деталь: | Manual Feed Tray Unit |
| Парткод: | A0P0 R724 00 |
| Деталь: | Paperfeed Relay Harness /6 |
| Парткод: | A00J N115 01 |
| Деталь: | Sensor Plate |
| Парткод: | A00J 5936 00 |
| Деталь: | Actuator /E |
| Парткод: | A00J 5937 00 |
| Деталь: | Torsion Spring /E |
| Парткод: | A00J 5938 00 |
| Деталь: | Bypass Tray /1 |
| Парткод: | A00J 5940 02 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5869 00 |
| Деталь: | LABEL |
| Парткод: | A00J 9426 01 |
| Деталь: | HOLDER |
| Парткод: | A00J 5976 00 |
| Деталь: | SCREW |
| Парткод: | 4036 5785 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5973 00 |
| Деталь: | Lifting Lever |
| Парткод: | A00J 5925 00 |
| Деталь: | FRICTION PLATE |
| Парткод: | A0P0 5996 00 |
| Деталь: | LIFTING PLATE |
| Парткод: | A00J 5946 02 |
| Деталь: | Holding Plate |
| Парткод: | A00J 5993 00 |
| Деталь: | HOLDER |
| Парткод: | A00J 5951 00 |
| Деталь: | Rack /R |
| Парткод: | A00J 5970 00 |
| Деталь: | COLLAR |
| Парткод: | 4036 3659 01 |
| Деталь: | Bypass Tray /2 |
| Парткод: | A00J 5941 01 |
| Деталь: | CLEANING PAD |
| Парткод: | 4131 4623 04 |
| Деталь: | Regulating Plate /R |
| Парткод: | A00J 5945 01 |
| Деталь: | Brake Part |
| Парткод: | A00J 5872 00 |
| Деталь: | Regulating Plate /L |
| Парткод: | A00J 5944 01 |
| Деталь: | SCALE METRIC |
| Парткод: | A00J 9428 01 |
| Деталь: | SCALE INCH |
| Парткод: | A00J 9429 01 |
| Деталь: | LABEL |
| Парткод: | A00J 9427 00 |
| Деталь: | SEAL |
| Парткод: | A00J 5898 00 |
| Деталь: | HOLDER |
| Парткод: | A00J 5660 00 |
| Деталь: | Pulling Spring /Middle |
| Парткод: | A00J 5669 00 |
| Деталь: | Idler Shaft |
| Парткод: | A0P0 5661 01 |
| Деталь: | ROLL |
| Парткод: | 4030 3122 01 |
| Деталь: | Paper feed Frame |
| Парткод: | A00J 5604 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3016 12 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | CLUTCH |
| Парткод: | A00J 5635 00 |
| Деталь: | GEAR 30T |
| Парткод: | 4425 3013 01 |
| Деталь: | GEAR 29T |
| Парткод: | 4030 3008 01 |
| Деталь: | Paper feed Holder |
| Парткод: | A00J 5601 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5603 02 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | Shaft /P |
| Парткод: | A00J 5640 00 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | SHAFT |
| Парткод: | 4040 3097 01 |
| Деталь: | Paper feed Shaft |
| Парткод: | A0P0 5602 00 |
| Деталь: | Release Lever |
| Парткод: | A00J 5673 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5668 01 |
| Деталь: | SHAFT |
| Парткод: | A00J 5665 00 |
| Деталь: | CONVEYANCE DRIVE CLUTCH |
| Парткод: | 57AA 8203 0 |
| Деталь: | GEAR 28T |
| Парткод: | A00J 5624 00 |
| Деталь: | WASHER |
| Парткод: | A00J 5663 00 |
| Деталь: | Timing belt 160L |
| Парткод: | A00J 5628 00 |
| Деталь: | Gear 22/32T |
| Парткод: | A00J 5623 00 |
| Деталь: | MOUNTING PLATE / PAPER FEED DRIVE |
| Парткод: | A00J R7AA 00 |
| Деталь: | Stepping motor |
| Парткод: | A0P0 M122 00 |
| Деталь: | Gear 24/42T |
| Парткод: | A00J 5622 00 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A00J 5625 01 |
| Деталь: | FRAME / PAPER FEED 1 |
| Парткод: | A00J R7AB 00 |
| Деталь: | Paper feed 1 assy |
| Парткод: | A0P0 R720 00 |
| Деталь: | Stepping motor |
| Парткод: | A0P0 M122 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 8950 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 8960 00 |
| Деталь: | Paper exit belt drive assy |
| Парткод: | A0P0 R736 00 |
| Деталь: | Pulley 24/29T |
| Парткод: | A00J 8952 00 |
| Деталь: | Timing belt 210L |
| Парткод: | A00J 8943 00 |
| Деталь: | WASHER |
| Парткод: | 1200 1646 03 |
| Деталь: | SHAFT |
| Парткод: | A00J 8958 00 |
| Деталь: | Gear 21/34T |
| Парткод: | A00J 8957 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0 8949 00 |
| Деталь: | COVER |
| Парткод: | A00J 8977 00 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 8994 00 |
| Деталь: | CAM |
| Парткод: | A0P0 8973 00 |
| Деталь: | GEAR 16T |
| Парткод: | A00J 8946 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 8972 00 |
| Деталь: | GEAR 16T |
| Парткод: | A00J 8953 00 |
| Деталь: | BUSHING |
| Парткод: | A0P0 9000 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 8948 00 |
| Деталь: | Gear 21T |
| Парткод: | A00J 8944 00 |
| Деталь: | Gear 21T |
| Парткод: | A00J 8945 00 |
| Деталь: | BUSHING |
| Парткод: | 4004 5339 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1500 21 |
| Деталь: | PAPER FEED MOTOR |
| Парткод: | A108 R705 00 |
| Деталь: | Registration Lower Motor |
| Парткод: | A108 R706 00 |
| Деталь: | ROLL |
| Парткод: | 9J07 5019 01 |
| Деталь: | Gear18T |
| Парткод: | A108 2132 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A108 2127 00 |
| Деталь: | Tension Plate B |
| Парткод: | A108 R7A1 00 |
| Деталь: | CLAW |
| Парткод: | A108 7014 00 |
| Деталь: | GUIDE |
| Парткод: | A108 7101 02 |
| Деталь: | Handle /Rear |
| Парткод: | A108 7111 00 |
| Деталь: | GUIDE |
| Парткод: | A108 7024 00 |
| Деталь: | BALL BEARING |
| Парткод: | 4131 2626 01 |
| Деталь: | ROLLER |
| Парткод: | A108 7013 01 |
| Деталь: | BALL BEARING |
| Парткод: | A00J 6178 00 |
| Деталь: | Slide Part |
| Парткод: | A108 7028 01 |
| Деталь: | Lifting Spring |
| Парткод: | A108 7026 01 |
| Деталь: | PRESSING PART |
| Парткод: | A108 7027 01 |
| Деталь: | SHAFT |
| Парткод: | A0HT 8908 00 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A108 7025 00 |
| Деталь: | DETECTING PLATE |
| Парткод: | A108 7022 00 |
| Деталь: | COLLAR |
| Парткод: | 9J08 2104 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108 R900 00 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N103 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | LEVER |
| Парткод: | 9J07 4008 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07 4009 02 |
| Деталь: | WASHER |
| Парткод: | 9J07 1606 00 |
| Деталь: | BRACKET |
| Парткод: | A07H 7501 12 |
| Деталь: | SHAFT |
| Парткод: | 9J07 4012 01 |
| Деталь: | GUIDE |
| Парткод: | A108 7019 02 |
| Деталь: | Neutralizing Brush |
| Парткод: | A07H 7502 00 |
| Деталь: | GUIDE |
| Парткод: | A108 7018 00 |
| Деталь: | ROLLER |
| Парткод: | A0HT 7006 00 |
| Деталь: | STOPPER |
| Парткод: | A108 7031 00 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 71 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 7110 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A108 7020 01 |
| Деталь: | TIMING BELT 122L |
| Парткод: | A108 2141 00 |
| Деталь: | Pulley 40T |
| Парткод: | A108 2143 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 7016 00 |
| Деталь: | Pulley 34/40T |
| Парткод: | A108 2122 00 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A108 7011 01 |
| Деталь: | SHAFT |
| Парткод: | A108 7035 00 |
| Деталь: | Timing belt 312L |
| Парткод: | A108 2121 00 |
| Деталь: | Pulley 40T |
| Парткод: | A108 2128 00 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 02 |
| Деталь: | Fixing Plate /2 |
| Парткод: | A108 7023 01 |
| Деталь: | Lock Plate /Front Stake |
| Парткод: | A108 R7A3 00 |
| Деталь: | Lock Plate/Rear Stake |
| Парткод: | A108 R7A4 00 |
| Деталь: | Cover Sheet |
| Парткод: | A108 7043 00 |
| Деталь: | GUIDE |
| Парткод: | A108 7036 00 |
| Деталь: | Guide Sheet |
| Парткод: | A108 7045 00 |
| Деталь: | DUCT |
| Парткод: | A0P0 1545 00 |
| Деталь: | Grounding Wire /1 |
| Парткод: | A1DM N135 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 1549 00 |
| Деталь: | DUCT |
| Парткод: | A0P0 1526 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 1537 00 |
| Деталь: | DUCT |
| Парткод: | A0P0 1521 00 |
| Деталь: | SEAL |
| Парткод: | A00J 1527 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0 1322 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1531 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1546 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | Smoke suction filter assy |
| Парткод: | A0P0 R701 00 |
| Деталь: | SEAL |
| Парткод: | 4036 2485 01 |
| Деталь: | SEAL |
| Парткод: | A00J 1548 01 |
| Деталь: | DUCT |
| Парткод: | A0P0 1533 00 |
| Деталь: | Grounding Wire /3 |
| Парткод: | A1DM N137 00 |
| Деталь: | C/K Contact Assy |
| Парткод: | A0P0 R718 00 |
| Деталь: | TERMINAL M ASSY |
| Парткод: | A00J R739 00 |
| Деталь: | Cover /Magenta |
| Парткод: | A00J 1185 00 |
| Деталь: | Developing Contact /Magenta |
| Парткод: | A00J 1181 00 |
| Деталь: | Contact /Magenta |
| Парткод: | A00J 1183 00 |
| Деталь: | TERMINAL Y ASSY |
| Парткод: | A00J R738 00 |
| Деталь: | Cover /Yellow |
| Парткод: | A00J 1184 00 |
| Деталь: | Developing Contact /Yellow |
| Парткод: | A00J 1180 00 |
| Деталь: | Contact /Yellow |
| Парткод: | A00J 1182 00 |
| Деталь: | Chaging Wiring /M |
| Парткод: | A00J N131 00 |
| Деталь: | Chaging Wiring /Y |
| Парткод: | A00J N130 00 |
| Деталь: | Chaging Wiring /K |
| Парткод: | A0P0 N133 00 |
| Деталь: | CHANGING WIRING |
| Парткод: | A00J N136 00 |
| Деталь: | Chaging Wiring /C |
| Парткод: | A00J N132 00 |
| Деталь: | CHANGING WIRING/2 |
| Парткод: | A00J N137 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0P0 1119 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4004 2317 01 |
| Деталь: | PIN |
| Парткод: | 4036 2311 01 |
| Деталь: | Contact2 assy |
| Парткод: | A0P0 R715 00 |
| Деталь: | TERMINAL 3 ASSY |
| Парткод: | A00J R734 00 |
| Деталь: | Developing Contact /Front |
| Парткод: | A00J 1108 00 |
| Деталь: | Holder /Color |
| Парткод: | A00J 1122 00 |
| Деталь: | Developing Contact /Middle |
| Парткод: | A00J 1109 00 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 1159 00 |
| Деталь: | Cover /Yellow |
| Парткод: | A00J 1128 00 |
| Деталь: | REINFORCE PLATE /2 |
| Парткод: | A00J 5727 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0902 01 |
| Деталь: | Paperfeed Relay harness /4 |
| Парткод: | A00J N119 02 |
| Деталь: | BRACKET |
| Парткод: | 4348 3049 01 |
| Деталь: | ROLLER |
| Парткод: | A00J 5722 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 5605 02 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 5610 00 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 5743 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3125 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J 5613 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5612 00 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A0P0 5617 00 |
| Деталь: | Mounting Plate /S |
| Парткод: | A00J 5646 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | Holder /S |
| Парткод: | A00J 5647 00 |
| Деталь: | Guide Roller /Rear |
| Парткод: | A00J 5748 00 |
| Деталь: | Fieldroller assy |
| Парткод: | A0P0 R740 00 |
| Деталь: | Release Lever |
| Парткод: | A0P0 5681 00 |
| Деталь: | GEAR 24T |
| Парткод: | A0P0 5704 00 |
| Деталь: | Conveyance Belt 74L |
| Парткод: | A0P0 5680 00 |
| Деталь: | Frame/Drive Moter |
| Парткод: | A0P0 R7A1 00 |
| Деталь: | Stepping motor |
| Парткод: | A0P0 M126 00 |
| Деталь: | Paperfeed Drive harness |
| Парткод: | A00J N10F 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 5731 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A0P0 5755 00 |
| Деталь: | Drive Holder /2 |
| Парткод: | A00J 5726 00 |
| Деталь: | Conveyance Gear /2 21/31T |
| Парткод: | A00J 5653 00 |
| Деталь: | Conveyance Gear /5 23T |
| Парткод: | A00J 5656 00 |
| Деталь: | Conveyance Gear /4 20/31T |
| Парткод: | A00J 5655 00 |
| Деталь: | FRAME / PAPER FEED 2 |
| Парткод: | A00J R7AE 00 |
| Деталь: | GEAR 22T |
| Парткод: | A00J 5744 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | Lock Catch |
| Парткод: | A00J 5742 01 |
| Деталь: | Wiring Cover /2 |
| Парткод: | A00J 5648 00 |
| Деталь: | Fieldroller assy |
| Парткод: | A0P0 R739 00 |
| Деталь: | MOTOR ASSY |
| Парткод: | 4037 R709 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 7102 00 |
| Деталь: | GEAR 16/64T |
| Парткод: | 4025 4906 01 |
| Деталь: | Gear 16/40T |
| Парткод: | 4025 4907 01 |
| Деталь: | GEAR 12/40T |
| Парткод: | 4025 4910 01 |
| Деталь: | Arm /Front |
| Парткод: | A0P0 7106 00 |
| Деталь: | WASHER |
| Парткод: | 4004 4722 02 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 7108 00 |
| Деталь: | GEAR 15T |
| Парткод: | 4025 4908 01 |
| Деталь: | 2ND TRANSFER RETRACTION DRIVE |
| Парткод: | A00J R7AU 00 |
| Деталь: | GEAR 15T |
| Парткод: | 4025 4909 01 |
| Деталь: | PIN |
| Парткод: | 4036 4911 01 |
| Деталь: | SHAFT |
| Парткод: | 4025 4709 02 |
| Деталь: | WASHER |
| Парткод: | 4004 4723 01 |
| Деталь: | ARM |
| Парткод: | 4036 4712 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4025 4725 01 |
| Деталь: | Cam /1 |
| Парткод: | A00J 7114 00 |
| Деталь: | CAM |
| Парткод: | 4004 4710 02 |
| Деталь: | PIN |
| Парткод: | 1144 5200 01 |
| Деталь: | Conveyance Wiring |
| Парткод: | A00J N110 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 7107 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | BUSHING |
| Парткод: | 4036 4730 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4025 4719 02 |
| Деталь: | Arm /Rear |
| Парткод: | A0P0 7105 01 |
| Деталь: | DETECTING PLATE |
| Парткод: | 4025 4720 01 |
| Деталь: | Support Shaft |
| Парткод: | A00J 7104 00 |
| Деталь: | Input Shaft |
| Парткод: | A00J 6014 02 |
| Деталь: | Ground Plate /2 |
| Парткод: | A00J 6057 00 |
| Деталь: | GEAR 18T |
| Парткод: | A00J 6010 00 |
| Деталь: | MOUNTING PLATE / LCC FEED DRIVE |
| Парткод: | A00J R7AK 00 |
| Деталь: | SPRING MOUNTING PLATE 1 |
| Парткод: | 56AA 4043 0 |
| Деталь: | BUSHING |
| Парткод: | A00J 6632 00 |
| Деталь: | SPRING MOUNTING PLATE 2 |
| Парткод: | 56AA 4044 0 |
| Деталь: | Ground Plate /Middle |
| Парткод: | A00J 6188 00 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 6047 01 |
| Деталь: | Idler Roll |
| Парткод: | A00J 6051 00 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 6048 00 |
| Деталь: | Idler Shaft |
| Парткод: | A00J 6052 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 6017 00 |
| Деталь: | WASHER |
| Парткод: | A00J 6029 00 |
| Деталь: | Pulley 15T |
| Парткод: | A00J 6195 00 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A00J 6185 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | Pulley 14T |
| Парткод: | A00J 6196 00 |
| Деталь: | Timing Belt 96L |
| Парткод: | A00J 6198 00 |
| Деталь: | ROLL /1 |
| Парткод: | A00J 6197 00 |
| Деталь: | Guide Washer |
| Парткод: | A0P0 6021 00 |
| Деталь: | Multi-feed Adjusting Plate |
| Парткод: | A00J 6016 00 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J 6015 01 |
| Деталь: | Gear 22/14T |
| Парткод: | A00J 6034 00 |
| Деталь: | CLEANER SHAFT HOLDER |
| Парткод: | 56AA 7505 0 |
| Деталь: | Paper feed Plate |
| Парткод: | A00J 6041 01 |
| Деталь: | PAPER FEED INPUT SHAFT |
| Парткод: | 56QA 4024 0D |
| Деталь: | Pressing Spring |
| Парткод: | 56AA 4051 0 |
| Деталь: | PAPER FEED COUPLING PART |
| Парткод: | 56AA 4045 0 |
| Деталь: | Gear43T |
| Парткод: | A00J 6009 00 |
| Деталь: | DUCT |
| Парткод: | A0P0 1501 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 1504 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | SEALING PART |
| Парткод: | A0P0 1511 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1502 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1506 00 |
| Деталь: | Duct /2 |
| Парткод: | A00J 1572 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 1575 00 |
| Деталь: | Duct /1 |
| Парткод: | A00J 1571 00 |
| Деталь: | Duct /3 |
| Парткод: | A00J 1573 01 |
| Деталь: | Duct /4 |
| Парткод: | A00J 1574 01 |
| Деталь: | Duct /5 |
| Парткод: | A00J 1575 01 |
| Деталь: | DUCT |
| Парткод: | A0P0 1577 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1579 01 |
| Деталь: | Duct /6 |
| Парткод: | A00J 1576 00 |
| Деталь: | DUCT |
| Парткод: | A0P0 1503 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 1505 00 |
| Деталь: | FAN MOTOR |
| Парткод: | A0P0 M142 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1510 02 |
| Деталь: | Grounding Wire /1 |
| Парткод: | A1DM N135 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 1576 00 |
| Деталь: | Slide Rail /A |
| Парткод: | A00J 6312 02 |
| Деталь: | Mounting Plate /Front |
| Парткод: | A00J 6316 00 |
| Деталь: | SCREW |
| Парткод: | A00J 6184 00 |
| Деталь: | SCREW |
| Парткод: | 1151 3300 01 |
| Деталь: | Holding Plate |
| Парткод: | A00J 6318 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6301 02 |
| Деталь: | SCREW |
| Парткод: | A00J 6317 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6308 00 |
| Деталь: | BUSHING |
| Парткод: | 1200 3121 09 |
| Деталь: | ARM |
| Парткод: | 9J07 4312 01 |
| Деталь: | STOPPER |
| Парткод: | 9J07 4314 01 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A108 7131 01 |
| Деталь: | PIN |
| Парткод: | 1067 2503 01 |
| Деталь: | STOPPER |
| Парткод: | 9J07 4315 01 |
| Деталь: | ROLL |
| Парткод: | 9J07 4302 01 |
| Деталь: | GUIDE |
| Парткод: | 9J07 4206 01 |
| Деталь: | SHAFT |
| Парткод: | 9J07 4307 01 |
| Деталь: | SHAFT |
| Парткод: | 9J07 4303 01 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A108 7130 01 |
| Деталь: | ARM |
| Парткод: | 9J07 4304 01 |
| Деталь: | PIN |
| Парткод: | 4131 2536 02 |
| Деталь: | LEVER |
| Парткод: | 9J07 4308 01 |
| Деталь: | Pressure/Release Motor Assy |
| Парткод: | A108 R702 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108 R900 00 |
| Деталь: | SEAL |
| Парткод: | 9J07 4420 01 |
| Деталь: | GEAR 26T |
| Парткод: | 9J07 4311 01 |
| Деталь: | CAM |
| Парткод: | 9J07 4309 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07 4204 02 |
| Деталь: | COVER |
| Парткод: | 9J07 4208 01 |
| Деталь: | GUIDE |
| Парткод: | 9J07 4202 03 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A108 7132 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07 4205 02 |
| Деталь: | GUIDE |
| Парткод: | 9J07 4209 01 |
| Деталь: | GUIDE |
| Парткод: | 9J07 4203 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030 3214 02 |
| Деталь: | GUIDE |
| Парткод: | 4030 3215 01 |
| Деталь: | GEAR 14T |
| Парткод: | 4658 3012 01 |
| Деталь: | Regulating Plate /ASSY |
| Парткод: | A00J 6212 02 |
| Деталь: | GUIDE |
| Парткод: | 4537 3317 01 |
| Деталь: | Guide Cushion |
| Парткод: | A00J 6236 00 |
| Деталь: | Regulating Plate /ASSY |
| Парткод: | A00J 6211 02 |
| Деталь: | KNOB |
| Парткод: | 4037 3204 01 |
| Деталь: | LEVER |
| Парткод: | 4128 3823 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4498 3825 01 |
| Деталь: | SHAFT |
| Парткод: | 4498 3826 01 |
| Деталь: | LABEL |
| Парткод: | A00J 9424 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3206 01 |
| Деталь: | CASSETTE |
| Парткод: | A0P0 A620 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6219 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6220 03 |
| Деталь: | Lifting Shaft |
| Парткод: | A0P0 6216 00 |
| Деталь: | LIFTING PLATE |
| Парткод: | A0P0 6215 00 |
| Деталь: | Auxiliary Plate |
| Парткод: | A00J 6235 00 |
| Деталь: | LABEL CARRYING CAPACITY |
| Парткод: | 4002 7306 01 |
| Деталь: | Lock Shaft |
| Парткод: | A00J 6222 00 |
| Деталь: | FRICTION PLATE |
| Парткод: | A00J 6234 00 |
| Деталь: | LEVER |
| Парткод: | A0P0 6237 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030 3226 01 |
| Деталь: | Read Cover /Right |
| Парткод: | A0P0 1633 00 |
| Деталь: | COVER |
| Парткод: | A00J 1691 00 |
| Деталь: | Read Cover /Front |
| Парткод: | A0P0 1658 00 |
| Деталь: | COVER |
| Парткод: | A02E 1677 00 |
| Деталь: | COVER |
| Парткод: | A0P0 1652 00 |
| Деталь: | Read Cover |
| Парткод: | A0P0 1676 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 1692 00 |
| Деталь: | Label Legal Restiriction |
| Парткод: | A00J 9401 00 |
| Деталь: | LABEL |
| Парткод: | A00J 9402 00 |
| Деталь: | Read Cover /Upper |
| Парткод: | A00J 1671 03 |
| Деталь: | Read Cover /Front |
| Парткод: | A0P0 1630 01 |
| Деталь: | Light blocking Plate |
| Парткод: | A00J 1689 02 |
| Деталь: | Lens /B |
| Парткод: | A00J 1682 02 |
| Деталь: | Light blocking Cover /C |
| Парткод: | A00J 1685 03 |
| Деталь: | PWB Assembly LED2 |
| Парткод: | A00J H00E 00 |
| Деталь: | Scanner Wiring /6 |
| Парткод: | A0P0 N146 00 |
| Деталь: | Read Cover /Left |
| Парткод: | A0P0 1659 00 |
| Деталь: | SEAL |
| Парткод: | A0P0 1666 00 |
| Деталь: | Read Cover /Left |
| Парткод: | A0P0 1632 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 2679 00 |
| Деталь: | Read Cover /Upper |
| Парткод: | A00J 1678 11 |
| Деталь: | Read Cover /Rear |
| Парткод: | A0P0 1631 01 |
| Деталь: | Read Cover /Upper |
| Парткод: | A0P0 1672 01 |
| Деталь: | LABEL |
| Парткод: | A1DM 9477 00 |
| Деталь: | GUIDE |
| Парткод: | A0P0 2673 00 |
| Деталь: | FILTER |
| Парткод: | 4025 2285 02 |
| Деталь: | Grounding Wire /2 |
| Парткод: | A1DM N136 00 |
| Деталь: | LABEL MAX |
| Парткод: | 9J07 9401 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A01H 5605 00 |
| Деталь: | SEAL |
| Парткод: | 4641 3503 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | A108 5617 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A01H 5604 00 |
| Деталь: | BRACKET |
| Парткод: | A0HT 5602 00 |
| Деталь: | ACTUATOR |
| Парткод: | 9J07 3107 01 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | Photoreflector |
| Парткод: | A108 M500 00 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N106 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A01H 5611 00 |
| Деталь: | LEVER |
| Парткод: | A108 5618 00 |
| Деталь: | GUIDE |
| Парткод: | 9J07 3411 02 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N105 00 |
| Деталь: | CAM |
| Парткод: | 4641 3417 02 |
| Деталь: | GUIDE |
| Парткод: | A108 5634 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 5630 00 |
| Деталь: | Lifting Motor assy |
| Парткод: | A108 R704 00 |
| Деталь: | HOLDER |
| Парткод: | A108 5632 00 |
| Деталь: | Gear 14/37T |
| Парткод: | A108 5633 00 |
| Деталь: | GEAR 13/28T |
| Парткод: | 4641 3415 01 |
| Деталь: | GEAR 30T |
| Парткод: | 4641 3436 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A108 5631 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 5626 00 |
| Деталь: | STOPPER |
| Парткод: | 9J07 3104 01 |
| Деталь: | GUIDE |
| Парткод: | A01H 5612 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J07 5600 00 |
| Деталь: | RACK |
| Парткод: | 9J07 3103 13 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N108 00 |
| Деталь: | GEAR 40T |
| Парткод: | 9J07 3105 02 |
| Деталь: | TRAY |
| Парткод: | A108 5611 03 |
| Деталь: | RESISTOR |
| Парткод: | V801 3000 06 |
| Деталь: | Spacer /B |
| Парткод: | A108 5642 00 |
| Деталь: | Spacer /A |
| Парткод: | A108 5643 00 |
| Деталь: | Stepping motor |
| Парткод: | A0HU M100 00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108 M501 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 2650 00 |
| Деталь: | Pulley 25L |
| Парткод: | A108 2657 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A108 2656 00 |
| Деталь: | TIMING BELT 190L |
| Парткод: | A0FD 8929 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A108 2707 00 |
| Деталь: | SHEET |
| Парткод: | A108 2701 00 |
| Деталь: | SHAFT |
| Парткод: | A108 2621 00 |
| Деталь: | BRUSH |
| Парткод: | A108 3002 00 |
| Деталь: | BUSHING |
| Парткод: | A108 2644 00 |
| Деталь: | SPACER |
| Парткод: | A108 2647 00 |
| Деталь: | SHEET |
| Парткод: | A108 2706 01 |
| Деталь: | Slide Part |
| Парткод: | A108 2702 00 |
| Деталь: | GUIDE |
| Парткод: | A108 2600 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A108 2664 00 |
| Деталь: | BUSHING |
| Парткод: | A108 2607 00 |
| Деталь: | GROUND PLATE |
| Парткод: | A108 2704 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A108 2646 01 |
| Деталь: | SHAFT |
| Парткод: | A108 2653 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LABEL |
| Парткод: | A108 9402 00 |
| Деталь: | COVER |
| Парткод: | A108 2604 03 |
| Деталь: | Slide Part |
| Парткод: | A108 2729 00 |
| Деталь: | COVER |
| Парткод: | A108 2667 01 |
| Деталь: | BALL BEARING |
| Парткод: | A00J 6178 00 |
| Деталь: | Conveyance Guide |
| Парткод: | A108 2601 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A108 2708 01 |
| Деталь: | PULLEY |
| Парткод: | A108 2658 00 |
| Деталь: | PULLEY |
| Парткод: | A108 2641 00 |
| Деталь: | Timing belt 146L |
| Парткод: | A108 2648 00 |
| Деталь: | FLANGE |
| Парткод: | A108 2642 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A108 2732 00 |
| Деталь: | HOLDER |
| Парткод: | A0P0 1039 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | ACTUATOR |
| Парткод: | A0P0 1075 00 |
| Деталь: | SHAFT |
| Парткод: | A0P0 1033 00 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4004 6854 01 |
| Деталь: | ACTUATOR |
| Парткод: | A0P0 1040 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A0P0 1034 01 |
| Деталь: | Protection Sheet |
| Парткод: | A0P0 1254 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1047 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1450 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1451 01 |
| Деталь: | LED ARRAY |
| Парткод: | A00J M303 01 |
| Деталь: | Light blocking Part |
| Парткод: | A00J 1452 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1070 01 |
| Деталь: | Guide Plate /Front |
| Парткод: | A00J 1025 00 |
| Деталь: | Sensor Relay harness /2 |
| Парткод: | A0P0 N12H 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0P0 1029 00 |
| Деталь: | SHEET |
| Парткод: | A00J 1074 01 |
| Деталь: | Regulating Block /Cyan |
| Парткод: | A0P0 4049 00 |
| Деталь: | Regulating Block /Cyan |
| Парткод: | A0P0 4060 00 |
| Деталь: | Regulating Block /Cyan |
| Парткод: | A0P0 4063 00 |
| Деталь: | Regulating Block /Magenta |
| Парткод: | A0P0 4050 00 |
| Деталь: | Regulating Block /Magenta |
| Парткод: | A0P0 4061 00 |
| Деталь: | Regulating Block /Magenta |
| Парткод: | A0P0 4064 00 |
| Деталь: | Regulating Block /Yellow |
| Парткод: | A0P0 4051 00 |
| Деталь: | Regulating Block /Yellow |
| Парткод: | A0P0 4062 00 |
| Деталь: | Regulating Block /Yellow |
| Парткод: | A0P0 4065 00 |
| Деталь: | COVER |
| Парткод: | A00J 1371 03 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J 1071 00 |
| Деталь: | Guide Plate /Rear |
| Парткод: | A0P0 1026 00 |
| Деталь: | ERASER LAMP ASSY |
| Парткод: | A00J R737 00 |
| Деталь: | LABEL |
| Парткод: | A0P0 9483 00 |
| Деталь: | LABEL |
| Парткод: | A0P0 9484 00 |
| Деталь: | LABEL |
| Парткод: | A0P0 9485 00 |
| Деталь: | SEAL |
| Парткод: | A1DM 4036 00 |
| Деталь: | Protection Plate |
| Парткод: | A1DM 4039 00 |
| Деталь: | TAPE |
| Парткод: | A0P0 2648 00 |
| Деталь: | GUIDE RAIL |
| Парткод: | A00J 1321 01 |
| Деталь: | High voltage unit /2 |
| Парткод: | A0P0 M408 00 |
| Деталь: | GUIDE RAIL |
| Парткод: | A00J 1326 00 |
| Деталь: | COVER |
| Парткод: | A00J 1409 00 |
| Деталь: | Guide Holder |
| Парткод: | A00J 1378 00 |
| Деталь: | Guide Rail /Right |
| Парткод: | A0P0 1323 00 |
| Деталь: | GUIDE RAIL |
| Парткод: | A00J 1355 00 |
| Деталь: | High voltage unit /1 |
| Парткод: | A0P0 M407 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1351 00 |
| Деталь: | Rail /Right |
| Парткод: | A00J 1327 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 1340 00 |
| Деталь: | Up/down Plate |
| Парткод: | A00J 6135 00 |
| Деталь: | DOUBLE FEED PREVENTIVE PLATE |
| Парткод: | 55VA 4093 0 |
| Деталь: | FRICTION PLATE |
| Парткод: | A00J 6234 00 |
| Деталь: | LCT UP DOWN WIRE RIGHT FRONT |
| Парткод: | 56QA 5811 0 |
| Деталь: | PAD |
| Парткод: | A0P0 6639 00 |
| Деталь: | Stopper Plate /1 |
| Парткод: | A00J 6151 01 |
| Деталь: | Light blocking Part |
| Парткод: | A00J 6603 00 |
| Деталь: | BUSHING |
| Парткод: | A00J 6632 00 |
| Деталь: | Up/down Pulley |
| Парткод: | A00J 6137 00 |
| Деталь: | Regulating Plate /1 |
| Парткод: | A0P0 6189 00 |
| Деталь: | Gear /1 |
| Парткод: | A0P0 6638 00 |
| Деталь: | Dumper |
| Парткод: | A0P0 6627 00 |
| Деталь: | Protection Cover |
| Парткод: | A00J 6190 11 |
| Деталь: | LCT SLIDE BOARD |
| Парткод: | 56QA 5804 1D |
| Деталь: | EXTERNAL PROTECTION PLATE |
| Парткод: | 56QA 5847 0D |
| Деталь: | Sensor Cover |
| Парткод: | A00J 6133 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | Protection Sheet |
| Парткод: | A00J 6606 00 |
| Деталь: | STOPPER RUBBER |
| Парткод: | A00J 6631 00 |
| Деталь: | REGISTRATION UNIT FIXED SCREW |
| Парткод: | 26NA 4544 0 |
| Деталь: | Connecting Plate |
| Парткод: | A00J 6150 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 6132 00 |
| Деталь: | PFU Relay harness /2 |
| Парткод: | A00J N11B 01 |
| Деталь: | Receiving Block |
| Парткод: | A00J 6193 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0P0 6156 00 |
| Деталь: | Up/down Shaft |
| Парткод: | A00J 6155 00 |
| Деталь: | LCT UP DOWN WIRE RIGHT REAR |
| Парткод: | 56QA 5812 0 |
| Деталь: | 1000-sheet tray M |
| Парткод: | A0P0 R725 00 |
| Деталь: | 1000-sheet tray I |
| Парткод: | A0P0 R726 00 |
| Деталь: | Cover /Rear |
| Парткод: | A0P0 1619 02 |
| Деталь: | COVER |
| Парткод: | A0P0 1656 01 |
| Деталь: | COVER |
| Парткод: | A0P0 1657 01 |
| Деталь: | Cover /Rear |
| Парткод: | A0P0 1620 03 |
| Деталь: | COVER |
| Парткод: | A0P0 1653 01 |
| Деталь: | Label Dehumidifier SW. |
| Парткод: | A00J 9454 00 |
| Деталь: | Label Controller |
| Парткод: | A00J 9458 00 |
| Деталь: | Cover /Rear |
| Парткод: | A00J 1618 03 |
| Деталь: | LABEL CAUTION |
| Парткод: | A00J 9457 00 |
| Деталь: | Label Only connect |
| Парткод: | A00J 9450 00 |
| Деталь: | Cover /Rear |
| Парткод: | A0P0 1617 00 |
| Деталь: | Cover /Rear |
| Парткод: | A0P0 1616 02 |
| Деталь: | Mounting Plate /T |
| Парткод: | A0P0 4025 00 |
| Деталь: | MAGNET |
| Парткод: | 9326 2900 06 |
| Деталь: | DETECTING PLATE |
| Парткод: | A0P0 4077 01 |
| Деталь: | Toner Drive harness |
| Парткод: | A0P0 N123 01 |
| Деталь: | Bushing /B |
| Парткод: | 65AA 3250 1 |
| Деталь: | Supply Casing |
| Парткод: | A0P0 4001 00 |
| Деталь: | SEAL |
| Парткод: | 4036 5349 03 |
| Деталь: | TENSION SPRING |
| Парткод: | 4036 5348 01 |
| Деталь: | SHUTTER |
| Парткод: | 4036 5347 02 |
| Деталь: | Cover /Lower |
| Парткод: | A0P0 4054 00 |
| Деталь: | Agitating Shaft |
| Парткод: | A0P0 4006 00 |
| Деталь: | Gear 45T |
| Парткод: | A00J 4017 00 |
| Деталь: | Toner supply Sheet |
| Парткод: | A0P0 4008 00 |
| Деталь: | PIN |
| Парткод: | A0P0 4078 00 |
| Деталь: | Protection Plate |
| Парткод: | A0P0 4079 00 |
| Деталь: | Supply Roller |
| Парткод: | A00J 4005 00 |
| Деталь: | GEAR 22T |
| Парткод: | A00J 4016 00 |
| Деталь: | Gear 17/44T |
| Парткод: | A00J 4019 00 |
| Деталь: | Gear 38/35T |
| Парткод: | A00J 4018 00 |
| Деталь: | Sub Hopper Assy |
| Парткод: | A0P0 R714 00 |
| Деталь: | Stepping motor |
| Парткод: | A00J M121 00 |
| Деталь: | DRIVEPANEL/H |
| Парткод: | A00J R7A1 00 |
| Деталь: | SEAL |
| Парткод: | A00J 4052 00 |
| Деталь: | Seal /A |
| Парткод: | A0P0 4022 00 |
| Деталь: | SEAL |
| Парткод: | A00J 4073 00 |
| Деталь: | PLATE NUT |
| Парткод: | 4011 5339 01 |
| Деталь: | SWITCH |
| Парткод: | 9334 2710 11 |
| Деталь: | Spring /A |
| Парткод: | A00J 4014 01 |
| Деталь: | Cover /Upper |
| Парткод: | A0P0 4003 00 |
| Деталь: | Regulating Claw |
| Парткод: | A00J 4012 00 |
| Деталь: | Receiving Block |
| Парткод: | A0P0 4068 00 |
| Деталь: | Shutter /H |
| Парткод: | A00J 4004 01 |
| Деталь: | Guide Cover /Left |
| Парткод: | A0P0 4056 00 |
| Деталь: | Guide Cover /Right |
| Парткод: | A0P0 4055 00 |
| Деталь: | Seal /S |
| Парткод: | A00J 4009 00 |
| Деталь: | COVER |
| Парткод: | A108 1601 02 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N104 00 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N100 00 |
| Деталь: | ADF Control Board ASSY |
| Парткод: | A108 RA01 01 |
| Деталь: | Wiring Guide |
| Парткод: | A108 1301 00 |
| Деталь: | SCREW |
| Парткод: | 4002 2581 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A108 1014 00 |
| Деталь: | Hinge /Left |
| Парткод: | A108 1003 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 9J07 2109 01 |
| Деталь: | Adjusting Plate |
| Парткод: | A108 1308 01 |
| Деталь: | MICRO-SWITCH |
| Парткод: | 9331 2200 31 |
| Деталь: | Hinge /Right |
| Парткод: | A108 1004 01 |
| Деталь: | DETECTING PLATE |
| Парткод: | A108 1310 00 |
| Деталь: | LEVER |
| Парткод: | 9J07 2007 02 |
| Деталь: | LABEL INSERT |
| Парткод: | A01H 9402 00 |
| Деталь: | BASE FRAME |
| Парткод: | A108 1050 03 |
| Деталь: | MAGNET |
| Парткод: | 9J07 1602 00 |
| Деталь: | CLEANING PAD |
| Парткод: | A108 9552 00 |
| Деталь: | Cleaning Part |
| Парткод: | A108 9551 01 |
| Деталь: | Holding Mat /1 |
| Парткод: | A108 1008 00 |
| Деталь: | LABEL |
| Парткод: | A108 9400 00 |
| Деталь: | COVER |
| Парткод: | A108 1600 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 9J07 2008 01 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N10B 00 |
| Деталь: | ADF Wiring |
| Парткод: | A108 N109 00 |
| Деталь: | LABEL |
| Парткод: | A108 9403 00 |
| Деталь: | GUIDE |
| Парткод: | A01H 1003 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A108 1311 00 |
| Деталь: | Fixing Plate |
| Парткод: | A108 1309 01 |
| Деталь: | GUIDE |
| Парткод: | A01H 1004 00 |
| Деталь: | GUIDE |
| Парткод: | A108 1307 00 |
| Деталь: | Fixing Plate /P |
| Парткод: | A108 1300 00 |
| Деталь: | Donau-DS unit |
| Парткод: | A108 R700 00 |
| Деталь: | COVER |
| Парткод: | A108 1020 00 |
| Деталь: | TAPE |
| Парткод: | A0P0 2648 00 |
| Деталь: | SHEET |
| Парткод: | A108 9404 00 |
| Деталь: | CUSHION |
| Парткод: | 4004 1829 02 |
| Деталь: | Swing Shaft |
| Парткод: | A00J 1210 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 1214 00 |
| Деталь: | KNOB |
| Парткод: | A00J 1209 00 |
| Деталь: | CLAW |
| Парткод: | A00J 1202 00 |
| Деталь: | Support Shaft |
| Парткод: | A00J 1203 00 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 1215 00 |
| Деталь: | Lever /Color |
| Парткод: | A00J 1201 00 |
| Деталь: | Mounting Plate /Black |
| Парткод: | A0P0 1208 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Mounting Plate /Cyan |
| Парткод: | A0P0 1213 00 |
| Деталь: | Mounting Plate /Left |
| Парткод: | A00J 1205 00 |
| Деталь: | Cushion /Lower |
| Парткод: | A00J 1212 00 |
| Деталь: | Mounting Plate /Right |
| Парткод: | A00J 1206 00 |
| Деталь: | IU Lock(YM) |
| Парткод: | A0P0 A140 00 |
| Деталь: | IU Lock (C) |
| Парткод: | A0P0 A141 00 |
| Деталь: | Paper feed Cover |
| Парткод: | A00J 6038 00 |
| Деталь: | COLLAR |
| Парткод: | 1134 3041 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6191 01 |
| Деталь: | Conveyance Roller |
| Парткод: | A00J 6011 11 |
| Деталь: | SHAFT |
| Парткод: | 1134 3042 02 |
| Деталь: | ACTUATOR |
| Парткод: | A00J 6040 02 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 6158 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6039 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | BUSHING |
| Парткод: | A00J 6632 00 |
| Деталь: | BALL BEARING |
| Парткод: | A00J 6178 00 |
| Деталь: | Guide Assy draw /2 |
| Парткод: | A00J 6037 00 |
| Деталь: | Regulating Plate /Front |
| Парткод: | A00J 6006 00 |
| Деталь: | CLUTCH |
| Парткод: | A00J 5635 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | Paper feed Shaft |
| Парткод: | A00J 6042 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 6030 00 |
| Деталь: | Level Actuator /1 |
| Парткод: | A00J 6024 01 |
| Деталь: | WASHER |
| Парткод: | A00J 6029 00 |
| Деталь: | Pulley 14T |
| Парткод: | A00J 6028 00 |
| Деталь: | Timing belt 102L |
| Парткод: | A00J 6027 00 |
| Деталь: | Paper feed Base frame /1 |
| Парткод: | A00J 6001 04 |
| Деталь: | Slide Shaft Holder |
| Парткод: | A03U 8128 00 |
| Деталь: | Paper feed Shaft /2 |
| Парткод: | A00J 6035 00 |
| Деталь: | SHAFT STOPPER |
| Парткод: | 55VA 4212 0 |
| Деталь: | PAPER FEED DRIVING CLUTCH |
| Парткод: | 56AA 8201 2 |
| Деталь: | BALL BEARING |
| Парткод: | A00J 6179 00 |
| Деталь: | HANDLE |
| Парткод: | A00J 6183 00 |
| Деталь: | AUXILIARY PART |
| Парткод: | A00J 6031 01 |
| Деталь: | Auxiliary Part /2 |
| Парткод: | A00J 6194 00 |
| Деталь: | PAPER FEED REGULATING BLOCK |
| Парткод: | 56AA 4038 0 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A00J 6004 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 6025 00 |
| Деталь: | COUPLING |
| Парткод: | A00J 6005 00 |
| Деталь: | Wiring Cover |
| Парткод: | A00J 6180 00 |
| Деталь: | PFU Relay harness /4 |
| Парткод: | A00J N11D 01 |
| Деталь: | WASHER |
| Парткод: | A00J 6607 00 |
| Деталь: | WASHER |
| Парткод: | A00J 6608 00 |
| Деталь: | 1500-sheet paper feed assy |
| Парткод: | A0P0 R722 11 |
| Деталь: | Cover /Middle |
| Парткод: | A00J 5981 01 |
| Деталь: | HOLDER |
| Парткод: | A00J 5864 00 |
| Деталь: | Pressure Holder |
| Парткод: | A00J 5935 00 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 5939 00 |
| Деталь: | FRAME / BYPASS (FRONT) |
| Парткод: | A00J R7AP 00 |
| Деталь: | Bypass Cover /Front |
| Парткод: | A00J 5982 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J 5888 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5948 00 |
| Деталь: | Mounting Plate /F |
| Парткод: | A00J 5992 00 |
| Деталь: | LOCK LEVER |
| Парткод: | A00J 5984 01 |
| Деталь: | HOLDER |
| Парткод: | A00J 5949 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 5855 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5854 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5856 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5966 02 |
| Деталь: | ROLL |
| Парткод: | A00J 5883 00 |
| Деталь: | Fixing Plate |
| Парткод: | A00J 5882 00 |
| Деталь: | Positioning Shaft |
| Парткод: | A00J 5947 01 |
| Деталь: | Hold Holder |
| Парткод: | A00J 5867 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5998 00 |
| Деталь: | Detecting Shaft |
| Парткод: | A00J 5857 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 5995 00 |
| Деталь: | Set Actuator |
| Парткод: | A00J 5988 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5851 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5866 00 |
| Деталь: | FRAME |
| Парткод: | A00J 5902 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 5997 00 |
| Деталь: | SEAL |
| Парткод: | A00J 5886 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Cover /Inside |
| Парткод: | A0P0 1654 00 |
| Деталь: | Cover /Right rear |
| Парткод: | A0P0 1627 00 |
| Деталь: | Cover /Right rear |
| Парткод: | A00J 1628 02 |
| Деталь: | COVER |
| Парткод: | A00J 1642 01 |
| Деталь: | Cover /Right front |
| Парткод: | A00J 1629 01 |
| Деталь: | Cover /Right |
| Парткод: | A0P0 1613 00 |
| Деталь: | Cover /Left |
| Парткод: | A00J 1606 04 |
| Деталь: | Label Blindfold |
| Парткод: | A0P0 1698 00 |
| Деталь: | Cover /Left rear |
| Парткод: | A00J 1614 00 |
| Деталь: | Cover /Left front |
| Парткод: | A00J 1605 01 |
| Деталь: | COVER |
| Парткод: | A00J 6181 01 |
| Деталь: | Paper feed Cover /1 |
| Парткод: | A00J 6012 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Conveyance Roller |
| Парткод: | A00J 6055 11 |
| Деталь: | BALL BEARING |
| Парткод: | A00J 6178 00 |
| Деталь: | Guide Assy draw /1 |
| Парткод: | A00J 6003 13 |
| Деталь: | Detection Actuator /2 |
| Парткод: | A00J 6033 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6032 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 6050 00 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA 4049 0 |
| Деталь: | BUSHING |
| Парткод: | A00J 6632 00 |
| Деталь: | Regulating Plate /Front |
| Парткод: | A00J 6006 00 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | CLUTCH |
| Парткод: | A00J 5635 00 |
| Деталь: | ACTUATOR |
| Парткод: | A00J 6043 01 |
| Деталь: | WASHER |
| Парткод: | A00J 6029 00 |
| Деталь: | Pulley 14T |
| Парткод: | A00J 6028 00 |
| Деталь: | Timing belt 102L |
| Парткод: | A00J 6027 00 |
| Деталь: | Paper feed Base frame /2 |
| Парткод: | A00J 6002 04 |
| Деталь: | SHAFT |
| Парткод: | A00J 6030 00 |
| Деталь: | Slide Shaft Holder |
| Парткод: | A03U 8128 00 |
| Деталь: | PAPER FEED DRIVING CLUTCH |
| Парткод: | 56AA 8201 2 |
| Деталь: | SHAFT STOPPER |
| Парткод: | 55VA 4212 0 |
| Деталь: | Paper feed Coupling /2 |
| Парткод: | A00J 6053 00 |
| Деталь: | Pressing Spring |
| Парткод: | A00J 6054 00 |
| Деталь: | WASHER |
| Парткод: | A00J 6607 00 |
| Деталь: | BALL BEARING |
| Парткод: | A00J 6179 00 |
| Деталь: | AUXILIARY PART |
| Парткод: | A00J 6031 01 |
| Деталь: | HANDLE |
| Парткод: | A00J 6183 00 |
| Деталь: | Auxiliary Part /2 |
| Парткод: | A00J 6194 00 |
| Деталь: | PAPER FEED REGULATING BLOCK |
| Парткод: | 56AA 4038 0 |
| Деталь: | PFU Relay harness /5 |
| Парткод: | A00J N11E 01 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A00J 6004 00 |
| Деталь: | Paper feed Shaft |
| Парткод: | A00J 6042 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 6026 00 |
| Деталь: | COUPLING |
| Парткод: | A00J 6005 00 |
| Деталь: | Paper feed Shaft /1 |
| Парткод: | A00J 6008 00 |
| Деталь: | PUNCH SPACER |
| Парткод: | 15AG 5028 0 |
| Деталь: | Detection Actuator /1 |
| Парткод: | A00J 6007 01 |
| Деталь: | Detection Actuator /1 |
| Парткод: | A00J 6159 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 6044 01 |
| Деталь: | WASHER |
| Парткод: | A00J 6608 00 |
| Деталь: | HOLDER |
| Парткод: | A0P0 6633 00 |
| Деталь: | Sealing Magnet |
| Парткод: | A00J 6609 00 |
| Деталь: | 1000 sheet paper feed |
| Парткод: | A0P0 R723 00 |
| Деталь: | ACTUATOR |
| Парткод: | A00J 7316 01 |
| Деталь: | PIN |
| Парткод: | A00J 7326 00 |
| Деталь: | HOLDER |
| Парткод: | A00J 7323 02 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J 7325 02 |
| Деталь: | SHAFT |
| Парткод: | A00J 7324 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0 7085 00 |
| Деталь: | HOLDER |
| Парткод: | A0P0 7077 01 |
| Деталь: | Temp. transfer |
| Парткод: | A0P0 M500 00 |
| Деталь: | Open/close Spring |
| Парткод: | A0P0 7076 00 |
| Деталь: | FLANGE |
| Парткод: | 4004 3512 02 |
| Деталь: | Hold Wire /Rear |
| Парткод: | A00J 7071 02 |
| Деталь: | Guide Wire |
| Парткод: | A00J 7075 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 7090 00 |
| Деталь: | Guide Holder |
| Парткод: | A0P0 7074 00 |
| Деталь: | Sensor Relay harness /3 |
| Парткод: | A0P0 N12J 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Temperature Detection harness |
| Парткод: | A0P0 N10U 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J P724 00 |
| Деталь: | Stepping motor |
| Парткод: | A0P0 M124 00 |
| Деталь: | Mounting plate / Paper exit motor |
| Парткод: | A0P0 R7A4 00 |
| Деталь: | Gear 16/26T |
| Парткод: | A00J 8911 00 |
| Деталь: | Idler Gear 22T |
| Парткод: | A0P0 8910 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 8966 00 |
| Деталь: | GEAR 16T |
| Парткод: | A00J 8951 00 |
| Деталь: | BUSHING |
| Парткод: | 4030 3093 01 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | A0P0 8907 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 8968 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J 8980 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J 8981 01 |
| Деталь: | CONTACT |
| Парткод: | A00J 8991 01 |
| Деталь: | Guide Lever |
| Парткод: | A00J 8905 01 |
| Деталь: | BUSHING |
| Парткод: | 4030 3823 01 |
| Деталь: | Pulling Spring |
| Парткод: | A00J 8938 00 |
| Деталь: | MOUNTING PLATE / PAPER EXIT (FRONT) |
| Парткод: | A0P0 R7A5 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 8965 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 8912 00 |
| Деталь: | COVER |
| Парткод: | A00J 8982 00 |
| Деталь: | LEVER |
| Парткод: | A00J 8913 00 |
| Деталь: | REVERSAL UPPER STAKE |
| Парткод: | A00J R7B5 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 8941 00 |
| Деталь: | SOLENOID |
| Парткод: | 9321 2200 32 |
| Деталь: | ROLL |
| Парткод: | 4004 5903 01 |
| Деталь: | SHAFT |
| Парткод: | 4025 5984 01 |
| Деталь: | SCREW |
| Парткод: | 4036 5966 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 8902 00 |
| Деталь: | Guide Plate /Lower |
| Парткод: | A0P0 8901 01 |
| Деталь: | Timing belt 86L |
| Парткод: | A0P0 9006 00 |
| Деталь: | CUSHION |
| Парткод: | A0P0 9008 00 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0P0 9004 00 |
| Деталь: | Riverse unit |
| Парткод: | A0P0 R735 00 |
| Деталь: | Riverse/exit Cover |
| Парткод: | A00J 8935 01 |
| Деталь: | Neutralizing Brush |
| Парткод: | A02E 8907 00 |
| Деталь: | WASHER |
| Парткод: | 1200 1646 03 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J 8995 00 |
| Деталь: | Riverse/exit Roller |
| Парткод: | A0P0 8939 00 |
| Деталь: | BUSHING |
| Парткод: | A00J 8904 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4011 5852 02 |
| Деталь: | CONTACT |
| Парткод: | A00J 8992 00 |
| Деталь: | CONTACT |
| Парткод: | A00J 8964 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 8934 02 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J 8993 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J 8932 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 8936 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 8933 00 |
| Деталь: | GUIDE PART |
| Парткод: | A00J 8985 00 |
| Деталь: | Pulley 24T |
| Парткод: | 4025 5939 01 |
| Деталь: | Paper exit Cover |
| Парткод: | A00J 8918 01 |
| Деталь: | COVER |
| Парткод: | A00J 8989 00 |
| Деталь: | SCREW |
| Парткод: | 4036 5966 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J06 M100 00 |
| Деталь: | Conveyance Relay harness /1 |
| Парткод: | A1DM N112 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J 8921 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J 8922 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 9010 00 |
| Деталь: | Paper exit Actuator |
| Парткод: | A00J 8923 00 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J 8931 00 |
| Деталь: | Sensor Plate |
| Парткод: | A00J 8927 00 |
| Деталь: | PROTECTION PART |
| Парткод: | A0P0 8996 00 |
| Деталь: | COVER |
| Парткод: | A00J 8984 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | BUSHING |
| Парткод: | 4030 3093 01 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J 8997 00 |
| Деталь: | CONTACT |
| Парткод: | A00J 8940 00 |
| Деталь: | ROLLER |
| Парткод: | A0P0 8983 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0P0 8929 01 |
| Деталь: | CUSHION |
| Парткод: | A0P0 9005 00 |
| Деталь: | ROLL |
| Парткод: | A0P0 9011 00 |
| Деталь: | PIN |
| Парткод: | A00J 8971 00 |
| Деталь: | ROLL |
| Парткод: | A00J 8970 00 |
| Деталь: | CONTACT |
| Парткод: | A00J 8942 00 |
| Деталь: | COVER |
| Парткод: | A00J 8979 00 |
| Деталь: | Plate spring /1 |
| Парткод: | A00J 8926 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J 8920 01 |
| Деталь: | PROTECTION PART |
| Парткод: | A0P0 8976 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0P0 8924 00 |
| Деталь: | SHAFT |
| Парткод: | A00J 8978 00 |
| Деталь: | Gear15T |
| Парткод: | A00J 8963 00 |
| Деталь: | GUIDE ASSY |
| Парткод: | A0P0 R737 11 |
| Деталь: | GEAR 16T |
| Парткод: | A00J 8961 00 |
| Деталь: | MOUNTING PLATE / 1ST EXIT |
| Парткод: | A00J R7B2 00 |
| Деталь: | BUSHING |
| Парткод: | A0P0 9002 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4036 5913 01 |
| Деталь: | BUSHING |
| Парткод: | 4004 5987 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 9001 00 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0P0 9007 00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0 9009 00 |
Коды ошибок
C0104
C0105
C0202
C0204
C0206
C0208
C0216
C0301
C0351
C1003
C1004
C1005
C1081
C1102
C1103
C1104
C1105
C1106
C1109
C1110
C1112
C1113
C1114
C1115
C1116
C1124
C1125
C1127
C1130
C1131
C1132
C1133
C1134
C1135
C1136
C1140
C1141
C1142
C1143
C1144
C1145
C1150
C1151
C1152
C1153
C1156
C1157
C1158
C1182
C1183
C1190
C1194
C11A1
C11A2
C11A7
C11B0
C11B2
C11B5
C11C0
C11E0
C11E1
C11E2
C2101
C2151
C2152
C2160
C2161
C2162
C2163
C2164
C2204
C2253
C2254
C2255
C2256
C2257
C2258
C2259
C225A
C225B
C225C
C2350
C2353
C2354
C2551
C2552
C2553
C2554
C2555
C2556
C2557
C2558
C2559
C255A
C255B
C255C
C2561
C2562
C2563
C2564
C2650
C2651
C2652
C2653
C2654
C2A14
C2A21
C2A22
C2A23
C2A24
C3101
C3102
C3201
C3202
C3303
C3304
C3305
C3424
C3425
C3721
C3722
C3724
C3725
C3822
C3824
C3825
C3921
C3922
C3924
C3925
C392A
C3B02
C3B03
C3B05
C3B06
C3B07
C3B08
C4101
C4301
C4501
C5104
C5105
C5304
C5306
C5351
C5354
C5356
C5370
C5372
C6001
C6002
C6102
C6103
C6104
C6105
C6301
C6303
C6704
C6751
C6752
C6753
C6754
C6755
C6901
C6902, C6903
C6911
C6912, C6913
C6F01
C8101
C8102
C8103
C8104
C8106
C8107
C8302
C8401
C9401
C9402
C9403
C9404
CA051
CA052
CA053
CB001...CB119
CC001
CC151
CC152
CC153
CC155
CC156
CC157
CC158
CC159, CC15A
CC15B
CC163
CC164
CC165
CC170...CC186
CC190
CC191
CD002
CD004, CD00F, CD020
CD010
CD011
CD041...CD046
CD047...CD04B
CD201...CD203
CD211, CD212
CD231
CD241, CD242
CD252
CD261
CD271
CD272
CD3##
CD401...CD407
CE001...CE007
CE002
CEEE1
CEEE2
CEEE3
CF001...CFF15
CFB00...CFFA0
Описание
| Error code: | C0104 |
| Description: | Tray 3/4 feeder transportation motor failure to turn The lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • LCC transport motor (M25) • Paper feed/transport drive board (PFTDB) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M25-PFTDB CN17 for proper connection and correct as necessary. 2 Check the connector of M25 for proper drive coupling and correct as necessary. 3 M25 operation check PFTDB CN17-1 to 7 11-X. 4 Replace M25. 5 PFTDB ICP6 conduction check. 6 Replace PFTDB. 7 Replace PRCB. |
| Error code: | C0105 |
| Description: | Tray 3/4 feeder transportation motor turning at abnormal timing The lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • LCC transport motor (M25) • Paper feed/transport drive board (PFTDB) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M25-PFTDB CN17 for proper connection and correct as necessary. 2 Check the connector of M25 for proper drive coupling and correct as necessary. 3 M25 operation check PFTDB CN17-1 to 7 11-X. 4 Replace M25. 5 PFTDB ICP6 conduction check. 6 Replace PFTDB. 7 Replace PRCB. |
| Error code: | C0202 |
| Description: | Magenta PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 1 upper limit sensor (PS6) • Tray 1 lift-up motor (M6) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0204 |
| Description: | Yellow PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 2 upper limit sensor (PS14) • Tray 2 lift-up motor (M8) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0206 |
| Description: | Black PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 3 upper limit sensor (PS22) • Tray 3 lift-up motor (M23) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0208 |
| Description: | Tray 5 feeder up/down abnormality |
| Causes: | • Tray 4 upper limit sensor (PS27) • Tray 4 lift-up motor (M24) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Error code: | C0216 |
| Description: | LCT up/down abnormality (When LU-205 or LU-303 is installed). The LU upper limit sensor (PS2) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began. |
| Causes: | • LU upper limit sensor (PS2) • LU lift-up motor (M1) • LU drive board (LUDB) |
| Remedy: | 1. Check the connector between M1-LUDB CN3 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-relay CN406-LUDB CN5 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: LUDB CN5-3 (ON) • Location of electrical component: LU-205/LU-303 4-G 5. M1 operation check • Control signal: LUDB CN3-4 (ON) • Location of electrical component: LU-205/LU-303 3-G 6. Replace M1. 7. Replace LUDB. (LU-205/LU-303) NOTICE • Link to the wiring diagram ( N.3.1 LU-205) • Link to the wiring diagram ( N.3.2 LU-303) |
| Error code: | C0301 |
| Description: | Suction fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Suction fan (FM1) • Paper feed/transport drive board (PFTDB) |
| Remedy: | 1 Check the FM8 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM8 operation check PRCB CN3PRCB-2 (ON) PRCB CN3PRCB-3 (LOCK) D-4 to 5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C0351 |
| Description: | Paper cooling fan/in`s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Paper cooling fan/in (FM12) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM12-relay CN325-MFPB CN27E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM12 operation check • Control signal: MFPB CN27E<B>-6 (LOCK) • Location of electrical component: 15-C 4. Replace FM12. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C1003 |
| Description: | PK communication error <When FS-535+PK-521 is installed> When a communication error is detected between the FS control board (FSCB) and the punch control board (PKCB). |
| Causes: | • Punch control board (PKCB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace PKCB. 4 Replace FSCB. |
| Error code: | C1004 |
| Description: | FNS communication error |
| Causes: | FS control board (FSCB) |
| Error code: | C1005 |
| Description: | ZU communication error When the ZU control board (ZUCB) is receiving data, a communication error is detected. |
| Causes: | ZU control board (ZUCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace ZUCB |
| Error code: | C1081 |
| Description: | SD communication error <When FS-534+SD-511 is installed> When a communication error is detected between the FS control board (FSCB) and the SD control board (SDDB). |
| Causes: | • SD drive board (SDDB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace SDDB. 4 Replace FSCB. |
| Error code: | C1102 |
| Description: | Main tray up/down motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • While the exit tray is being lifted, the main tray upper position sensor (PS26/PS27) is not turned ON (blocked) and the main tray upper position detect switch (SW2) is not turned ON, even after the main tray up/down motor (M11) turns by the set number of times. • While the exit tray is being lowered, the main tray full detection sensor (PS29) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M11) is turned ON. <When FS-537 or FS-537SD is installed> • The main tray lift up detection sensor (PS16/PS17) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/ down motor (M6) is turned ON. • The main tray full detection sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M6) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Main tray up/down motor (M11) • Main tray upper position sensor/R (PS26) • Main tray upper position sensor/F (PS27) • Main tray full detection sensor (PS29) • Main tray upper position detect switch (SW2) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Main tray up/down motor (M6) • Main tray lift up detection sensor/F (PS16) • Main tray lift up detection sensor/R (PS17) • Main tray full detection sensor (PS12) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M11-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M11 for proper drive coupling, and correct as necessary. 3. Check the connector between PS26-relay CN1-FSCB J14 for proper connection and correct as necessary. 4. Check the connector between PS27-relay CN1-FSCB J14 for proper connection and correct as necessary. 5. Check the connector between PS29-relay CN2-FSCB J14 for proper connection and correct as necessary. 6. Check the connector between SW2-FSCB J10 for proper connection and correct as necessary. 7. PS26 I/O check, sensor check • Control signal: FSCB J14<A>-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-C 8. PS27 I/O check, sensor check • Control signal: FSCB J14<B>-6 (ON) • Location of electrical component: FS-536/FS-536SD 3-C 9. PS29 I/O check, sensor check • Control signal: FSCB J14<A>-8 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 10. SW2 operation check • Control signal: FSCB J10-1 to 2 • Location of electrical component: FS-536/FS-536SD 15-K 11. M11 operation check • Control signal: FSCB J9<A>-9 to 10 • Location of electrical component: FS-536/FS-536SD 12-C 12. Replace M11. 13. FSCB F2 conduction check 14. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M6-FSCB J23 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS16-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 4. Check the connector between PS17-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 5. Check the connector between PS12-relay CN9-FSCB J19 for proper connection and correct as necessary. 6. PS16 I/O check, sensor check • Control signal: FSCB J20<B>-4 (ON) • Location of electrical component: FS-537/FS-537SD 11 to 12-D 7. PS17 I/O check, sensor check • Control signal: FSCB J20<B>-7 (ON) • Location of electrical component: FS-537/FS-537SD 12-D 8. PS12 I/O check, sensor check • Control signal: FSCB J19-7 (ON) • Location of electrical component: FS-537/FS-537SD 10-D 9. M6 operation check • Control signal: FSCB J23-1 to 11 • Location of electrical component: FS-537/FS-537SD 13-D 10. Replace M6. 11. FSCB F3 conduction check 12. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1103 |
| Description: | Alignment motor/Front’s drive malfunction. <When FS-536 or FS-536SD is installed> • The alignment plate/F home sensor (PS12) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M7) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. <When FS-537 or FS-537SD is installed> • The alignment plate/F home sensor (PS9) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS9) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M14) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. |
| Causes: | <When FS-536 or FS-536SD is installed> • Alignment motor/Front (M7) • Alignment plate/F home sensor (PS12) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Alignment motor/Front (M14) • Alignment plate/F home sensor (PS9) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M7-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS12-FSCB J4 for proper connection and correct as necessary. 4. PS12 I/O check, sensor check • Control signal: FSCB J4<B>-4 (ON) • Location of electrical component: FS-536/FS-536SD 15-C 5. M7 operation check • Control signal: FSCB J4<A>-5 to 8 • Location of electrical component: FS-536/FS-536SD 14-C 6. Replace M7. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M14-relay CN5-FSCB J18 for proper connection and correct as necessary. 2. Check the connector of M14 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-relay CN5-FSCB J18 for proper connection and correct as necessary. 4. PS9 I/O check, sensor check • Control signal: FSCB J18-10 (ON) • Location of electrical component: FS-537/FS-537SD 6-D 5. M14 operation check • Control signal: FSCB J18-1 to 4 • Location of electrical component: FS-537/FS-537SD 6-D 6. Replace M14. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1104 |
| Description: | Stacker plate drive motor`s malfunction. <When FS-537 or FS-537SD is installed> The stacker plate home sensor (PS30) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stacker plate drive motor (M3) is turned ON. |
| Causes: | • Stacker plate drive motor (M3) • Stacker plate home sensor (PS30) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M3-relay CN1<B>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS30-relay CN2-relay CN1<B>-FSCB J22 for proper connection and correct as necessary. 4. PS30 I/O check, sensor check • Control signal: FSCB J22<B>-10 (ON) • Location of electrical component: FS-537/FS-537SD 3-D 5. M3 operation check • Control signal: FSCB J22<B>1 to 2 • Location of electrical component: FS-537/FS-537SD 2-D 6. Replace M3. 7. Replace FSCB. NOTICE: • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1105 |
| Description: | Bundle eject motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • The gripper home position sensor (PS18) is not turned ON (unblocked) even after the set period of time has elapsed after the gripper position detection sensor (PS19) turns OFF (block). • The gripper position detection sensor (PS19) is not turned OFF (blocked) even after the set period of time has elapsed after PS19 turns ON (unblock). • The gripper position detection sensor (PS19) is not turned ON (unblocked) even after the set period of time has elapsed after the gripper home position sensor (PS18) turns OFF (block). • The gripper home position sensor (PS18) is not turned OFF (blocked) even after the set period of time has elapsed after the bundle eject motor (M10) is energized. • The gripper home position sensor (PS18) and the gripper position detection sensor (PS19) is turned ON (unblocked) at the same time. <When FS-537 or FS-537SD is installed> The gripper home position sensor (PS3) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed after the bundle eject motor (M1) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Bundle eject motor (M10) • Gripper home position sensor (PS18) • Gripper position detection sensor (PS19) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Bundle eject motor (M1) • Gripper home position sensor (PS3) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M10-relay CN7<A>-FSCB J13 for proper connection and correct as necessary. 2. Check the connector of M10 for proper drive coupling, and correct as necessary. 3. Check the connector between PS18-relay CN7<A>-FSCB J13 for proper connection and correct as necessary. 4. Check the connector between PS19-relay CN8<B>-FSCB J12 for proper connection and correct as necessary. 5. PS18 I/O check, sensor check • Control signal: FSCB J13-13 (ON) • Location of electrical component: FS-536/FS-536SD 8-C 6. PS19 I/O check, sensor check • Control signal: FSCB J12-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 7. M10 operation check • Control signal: FSCB J13-1 to 2 • Location of electrical component: FS-536/FS-536SD 9-C 8. Replace M10. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M1-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS3-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 4. PS3 I/O check, sensor check • Control signal: FSCB J22<A>-13 (ON) • Location of electrical component: FS-537/FS-537SD 2-D 5. M1 operation check • Control signal: FSCB J22<A>-1 to 2 • Location of electrical component: FS-537/FS-537SD 1-D 6. Replace M1. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1106 |
| Description: | Stapler movement motor’s malfunction. <When FS-536 or FS-536SD is installed> • The stapler home position sensor (rear) (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the side stapler movement motor (M13) turned ON. • The stapler does not reach the specified position within the set period of time. <When FS-537 or FS-537SD is installed> • The stapler home position sensor (PS18/PS19) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler movement motor (M19) turned ON. • The stapler does not reach the specified position within the set period of time. |
| Causes: | <When FS-536 or FS-536SD is installed> • Side stapler movement motor (M13) • Stapler home position sensor (rear) (PS23) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler movement motor (M19) • Stapler home position sensor (corner) (PS18) • Stapler home position sensor (rear) (PS19) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M13-relay CN3-FSCB J11 for proper connection, and correct as necessary. 2. Check the connector of M13 for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 5. M13 operation check • Control signal: FSCB J11<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 4-C 6. Replace M13. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M19-FSCB J17 for proper connection and correct as necessary. 2. Check the connector of M19 for proper drive coupling and correct as necessary. 3. Check the connector between PS18-FSCB J16 for proper connection and correct as necessary. 4. Check the connector between PS19-FSCB J16 for proper connection and correct as necessary. 5. PS18 I/O check, sensor check • Control signal: FSCB J16-9 (ON) • Location of electrical component: FS-537/FS-537SD15-D 6. PS19 I/O check, sensor check • Control signal: FSCB J16-6 (ON) • Location of electrical component: FS-537/FS-537SD 15-D 7. M19 operation check • Control signal: FSCB J17-10 to 13 • Location of electrical component: FS-537/FS-537SD 14-D 8. Replace M19. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1109 |
| Description: | Stapler motor’s malfunction. <When FS-536 or FS-536SD is installed> • The stapler home position sensor (rear) (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler motor (M14) turned ON. • The stapler position sensor (center) (PS24) is turned ON (blocked), when the stapler motor (M14) is running. <When FS-537 or FS-537SD is installed> • The stapler home position sensor (PS18/PS19) is not turned (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler movement motor (M5) turned ON. • The stapler position sensor (center) (PS20) is turned ON (blocked), when the stapler motor (M5) is running. |
| Causes: | <When FS-536 or FS-536SD is installed> • Stapler unit • Stapler home position sensor (rear) (PS23) • Stapler position sensor (center) (PS24) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler unit • Stapler home position sensor (corner) (PS18) • Stapler home position sensor (rear) (PS19) • Stapler position sensor (center) (PS20) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between the stapler unit-relay CN4-FSCB J11 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. Check the connector between PS24-relay CN3-FSCB J11 for proper connection and correct as necessary. 5. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 6. PS24 I/O check, sensor check • Control signal: FSCB J11<B>-6 • Location of electrical component: FS-536/FS-536SD 5-C 7. Replace the stapler unit. 8. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between the stapler unit-FSCB J17 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS18-FSCB J16 for proper connection and correct as necessary. 4. Check the connector between PS19-FSCB J16 for proper connection and correct as necessary. 5. Check the connector between PS20-FSCB J16 for proper connection and correct as necessary. 6. PS18 I/O check, sensor check • Control signal: FSCB J16-9 • Location of electrical component: FS-537/FS-537SD 15-D 7. PS19 I/O check, sensor check • Control signal: FSCB J16-6 • Location of electrical component: FS-537/FS-537SD 15-D 8. PS20 I/O check, sensor check • Control signal: FSCB J16-3 • Location of electrical component: FS-537/FS-537SD 15-D 9. Replace the stapler unit. 10. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1110 |
| Description: | PF lift motor 2 error |
| Causes: | [The left cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because of one of the phenomena below. 1. PF lift sensor 2 does not turn on when passing 23s while PF lift motor 2 turns on for the first time after inserting the cassette. 2. PF lift sensor 2 does not turn on when passing 2s while PF lift motor 2 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 2 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 2 - PF main PWB Wiring diagram 4 Replacing PF lift motor 2 PF lift motor 2 is faulty. Replace PF lift motor 2. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •PF lift sensor 2 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 2 is not properly attached or faulty. Reattach PF lift sensor 2. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1112 |
| Description: | Stapler motor`s drive malfunction. <When FS-536SD or FS-537SD is installed> • The stapler home sensor is not turned ON even after the set period of time has elapsed while the stapler motor is energized. • The stapler home sensor is not turned OFF even after the set period of time has elapsed after the stapler home sensor is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Staple unit • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between the staple unit-SDCB J4 for proper connection and correct as necessary. 2. Check the connector of the staple unit for proper drive coupling and correct as necessary. 3. Replace the staple unit. (FS-536SD/FS-537SD) 4. Replace SDCB. (FS-536SD/FS-537SD) 5. Replace FSCB. (FS-536SD/FS-537SD) |
| Error code: | C1113 |
| Description: | Stopper drive motor`s malfunction. <When FS-536SD or FS-537SD is installed> The stopper home sensor (PS6) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stopper drive motor (M4) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Stopper drive motor (M4) • Stopper home sensor (PS6) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M4-SDCB J10 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-SDCB J10 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: SDCB J10-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 2-P 5. M4 operation check • Control signal: SDCB J10-6 to 9 • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 1-P 6. Replace M4. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1114 |
| Description: | Alignment motor’s malfunction. <When FS-536SD or FS-537SD is installed> The alignment home sensor (PS4) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the alignment motor (M3) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Alignment motor (M3) • Alignment home sensor (PS4) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M3-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS4-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS4 I/O check, sensor check • Control signal: SDCB J7-6 (ON) • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 5. M3 operation check • Control signal: SDCB J7-7 to 10 • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 6. Replace M3. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1115 |
| Description: | Center fold knife motor`s malfunction. <When FS-536SD or FS-537SD is installed> The center fold knife home sensor (PS8) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Center fold knife motor (M9) • Center fold knife home sensor (PS8) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M9-SDCB J11 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS8-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS8 I/O check, sensor check • Control signal: SDCB J7-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-P, FS-537/FS-537SD 6-P 5. M9 operation check • Control signal: SDCB J11-11 to 20 • Location of electrical component: FS-536/FS-536SD 2-L, FS-537/FS-537SD 1-K 6. Replace M9. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1116 |
| Description: | Center-staple transfer motor malfunction <When FS-526+SD-508 is installed> • The transport motor (M33) does not reach the specified speed even after the set period of time has elapsed after it starts to operate. <When FS-527+SD-509 is installed> • The center fold roller motor (M25) does not reach the specified speed even after the set period of time has elapsed after it starts to operate. |
| Causes: | When FS-526+SD-508 is installed: Transport motor (M33) SD drive board (SDDB) FS control board (FSCB). When FS-527+SD-509 is installed: Center fold roller motor (M25) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | When FS-526+SD-508 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M33 for proper drive coupling, and correct as necessary. - - 3 M33 operation check SDDB CN409-1 to 11 SD-508 K-5 4 Change M33 - - 5 SDDB ICP5 conduction check - - 6 Change SDDB - - 7 Change FSCB. When FS-527+SD-509 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M25 for proper drive coupling, and correct as necessary. - - 3 M25 operation check SDDB PJ4-1 to 11 SD-509 B-3 4 Change M25 - - 5 Change SDDB - - 6 Change FSCB |
| Error code: | C1124 |
| Description: | Tray lift motor /Lw`s drive malfunction. <When FS-537+PI-507 or FS-537SD+PI-507 is installed> The tray upper limit sensor /Lw (PS209) or tray lower limit sensor /Lw (PS210) is not turned ON (blocked) after the set period of time has elapsed after the tray lift motor /Lw (M202) is turned ON. |
| Causes: | • Tray lift motor /Lw (M202) • Tray upper limit sensor /Lw (PS209) • Tray lower limit sensor /Lw (PS210) • PI drive board (PIDB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M202-relay CN206-PIDB CN56 for proper connection and correct as necessary. 2. Check the connector of M202 for proper drive coupling and correct as necessary. 3. Check the connector between PS209-relay CN237-PIDB CN53 for proper connection and correct as necessary. 4. Check the connector between PS210-relay CN236-PIDB CN53 for proper connection and correct as necessary. 5. PS209 I/O check, sensor check • Control signal: PIDB CN53<A>-8 (ON) • Location of electrical component: PI-507 10-C 6. PS210 I/O check, sensor check • Control signal: PIDB CN53<A>-11 (ON) • Location of electrical component: PI-507 11-C 7. M202 operation check • Control signal: PIDB CN56-5 to 6 • Location of electrical component: PI-507 9-C 8. Replace M202. 9. Replace PIDB. 10. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.6 PI-507) |
| Error code: | C1125 |
| Description: | Tray lift motor /Up`s drive malfunction. <When FS-537+PI-507 or FS-537SD+PI-507 is installed> The tray upper limit sensor /Up (PS205) or tray lower limit sensor /Up (PS204) is not turned ON (blocked) after the set period of time has elapsed after the tray lift motor /Up (M201) is turned ON. |
| Causes: | • Tray lift motor /Up (M201) • Tray upper limit sensor /Up (PS204) • Tray lower limit sensor /Up(PS205) • PI drive board (PIDB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M201-relay CN203-PIDB CN54 for proper connection and correct as necessary. 2. Check the connector of M201 for proper drive coupling and correct as necessary. 3. Check the connector between PS204-relay CN235-PIDB CN55 for proper connection and correct as necessary. 4. Check the connector between PS205-relay CN235-PIDB CN55 for proper connection and correct as necessary. 5. PS204 I/O check, sensor check • Control signal: PIDB CN55-8 (ON) • Location of electrical component: PI-507 8-C 6. PS205 I/O check, sensor check • Control signal: PIDB CN55-7 (ON) • Location of electrical component: PI-507 8-C 7. M201 operation check • Control signal: PIDB CN54-7 to 8 • Location of electrical component: PI-507 6 to 7-C 8. Replace M201. 9. Replace PIDB. 10. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.6 PI-507) |
| Error code: | C1127 |
| Description: | Punch oscillating motor’s drive malfunction. <When FS-537+PK-523 or FS-537SD+PK-523 is installed> The PKpunch oscillatinghome sensor (PS303) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the punch oscillating motor (M302) is energized. |
| Causes: | • Punch oscillating motor (M302) • PK punch oscillatinghome sensor (PS303) • Punch control board (PKCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M302-relay CN342-relay CN341-PKCB CN1 for proper connection and correct as necessary. 2. Check the connector of M302 for proper drive coupling and correct as necessary. 3. Check the connector between PS303-relay CN342-relay CN341-PKCB CN37 for proper connection and correct as necessary. 4. PS303 I/O check, sensor check • Control signal: PKCB CN37-2 (ON) • Location of electrical component: PK-523 5-C 5. M302 operation check • Control signal: PKCB CN1-1 to 6 • Location of electrical component: PK-523 5-C 6. Replace M302. 7. PKCB ICP2 conduction check. 8. Replace PKCB. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.4 PK-523) |
| Error code: | C1130 |
| Description: | PF right lift position problem (optional 3000-sheet paper feeder) Level switch 2 does not turn on within 30 s of PF lift motor 1 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 2. Defective PF lift motor 1. The PF right lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 2. Check if YC5-7 on the PF main PWB goes low when level switch 2 is turned off. If not, replace PF lift switch 2. Defective PF lift motor 2. Check for continuity across the coil. If none, replace PF lift motor 2. The PF right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C1131 |
| Description: | Folding guide motor’s drive malfunction. <When FS-537+ZU-609 or FS-537SD+ZU-609 is installed> The guide home sensor (PS500) is not turned ON (blocked) even after the set period of time has elapsed after the folding guide motor (M501) is turned ON. |
| Causes: | • Folding guide motor (M501) • Guide home sensor (PS500) • ZU drive board (ZUDB) |
| Remedy: | 1. Check the connector between M501-ZUDB CN6 for proper connection and correct as necessary. 2. Check the connector of M501 for proper drive coupling and correct as necessary. 3. Check the connector between PS500-ZUDB CN5 for proper connection and correct as necessary. 4. PS500 I/O check, sensor check • Control signal: ZUDB CN5-3 (ON) • Location of electrical component: ZU-609 3-B 5. M501 operation check • Control signal: ZUDB CN6-9 to 12 • Location of electrical component: ZU-609 2-B 6. Replace M501. 7. Replace ZUDB. NOTICE • Link to the wiring diagram ( N.3.5 ZU-609) |
| Error code: | C1132 |
| Description: | Punch drive motor’s drive malfunction. <When FS-536+PK-520 or FS-536SD+PK-520 is installed> The punch home sensor (PS1) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the punch drive motor (M1) is energized. <When FS-537+PK-523 or FS-537SD+PK-523 is installed> The PK punch home sensor/2(PS301) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the punch drive motor (M301) is energized. |
| Causes: | <When FS-536+PK-520 or FS-536SD+PK-520 is installed> • Punch drive motor (M1) • Punch home sensor (PS1) • FS control board (FSCB) <When FS-537+PK-523 or FS-537SD+PK-523 is installed> • Punch drive motor (M301) • PK punch home sensor/2(PS301) • Punch control board (PKCB) • FS control board (FSCB) |
| Remedy: | (a) When FS-536+PK-520 or FS-536SD+PK-520 is installed 1. Check the connector between M1-relay CN351-FSCB J7 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS1-FSCB J7 for proper connection and correct as necessary. 4. PS1 I/O check, sensor check • Control signal: FSCB J7-5 (ON) • Location of electrical component: FS-536/FS-536SD 13-K 5. M1 operation check • Control signal: FSCB J7-7 to 8 • Location of electrical component: FS-536/FS-536SD 13-K 6. Replace M1. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537+PK-523 or FS-537SD+PK-523 is installed 1. Check the connector between M301-relay CN351-PKCB CN35 for proper connection and correct as necessary. 2. Check the connector of M301 for proper drive coupling and correct as necessary. 3. Check the connector between PS301-PKCB CN36 for proper connection and correct as necessary. 4. PS301 I/O check, sensor check • Control signal: PKCB CN36-5 (ON) • Location of electrical component: PK-523 3-C 5. M301 operation check • Control signal: PKCB CN35-1 to 3 • Location of electrical component: PK-523 2-C 6. Replace M301. 7. Replace PKCB. 8. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.4 PK-523) |
| Error code: | C1133 |
| Description: | Pressure motor’s malfunction. <When FS-537+ZU-609 or FS-537SD+ZU-609 is installed> The press home sensor (PS502) is not turned ON (unblocked), or is not turned OFF (blocked) after it is turned ON (unblocked), even after the set period of time has elapsed after the pressure motor (M502) starts searching its home position |
| Causes: | • Pressure motor (M502) • Press home sensor (PS502) • ZU drive board (ZUDB) |
| Remedy: | 1. Check the connector between M502-ZUDB CN6 for proper connection and correct as necessary. 2. Check the connector of M502 for proper drive coupling and correct as necessary. 3. Check the connector between PS502-ZUDB CN5 for proper connection and correct as necessary. 4. PS502 I/O check, sensor check • Control signal: ZUDB CN5-6 (ON) • Location of electrical component: ZU-609 4-B 5. M502 operation check • Control signal: ZUDB CN6-7 (DRV) • Location of electrical component: ZU-609 2-B 6. Replace M502. 7. ZUDB ICP3 conduction check. 8. Replace ZUDB. NOTICE • Link to the wiring diagram ( N.3.5 ZU-609) |
| Error code: | C1134 |
| Description: | Main motor cooling fan’s drive malfunction <When FS-535+ZU-606 is installed> Even after the set period of time has elapsed after the main motor cooling fan (FM601) is turned ON, the FM601 EM signal is faulty and the fan is turned OFF; the signal is faulty after each of the following three trials. |
| Causes: | • Main motor cooling fan (FM601) • ZU control board (ZUCB) |
| Remedy: | 1 Check the connector between FM601-relay CN653- ZUCB CN11 for proper connection, and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM601 operation check ZUCB CN11-11 (DRV) ZU-606 8 to 9-C. 4 Replace FM601. 5 ZUCB ICP8 conduction check. 6 Replace ZUCB. |
| Error code: | C1135 |
| Description: | Punch motor’s drive malfunction <When FS-535+ZU-606 is installed> The punch motor (M604) is not turned OFF even after the set period of time has elapsed after it is turned ON. |
| Causes: | • Punch motor (M604) • ZU control board (ZUCB) |
| Remedy: | 1 Check the connector between M604-relay CN644- relay CN638-ZUCB CN11 for proper connection, and correct as necessary. 2 Check the connector of M604 for proper drive coupling, and correct as necessary. 3 M604 operation check ZUCB CN11-2 (DRV) ZU-606 7-C. 4 Replace M604. 5 ZUCB ICP10 conduction check. 6 Replace ZUCB. |
| Error code: | C1136 |
| Description: | Punch switchover motor’s drive malfunction <When FS-535+ZU-606 is installed> The punch switchover switch (MS601) is not turned OFF from the ON position, or not turned ON from the OFF position, even after the set period of time has elapsed after the punch switchover motor (M608) is turned ON. |
| Causes: | • Punch switchover motor (M608) • Punch switchover switch (MS601) • ZU control board (ZUCB) |
| Remedy: | 1 Check the connector between M608-relay CN633- relay CN638-ZUCB CN11 for proper connection, and correct as necessary. 2 Check the connector of M608 for proper drive coupling, and correct as necessary. 3 Check the connector between MS601-relay CN633- relay CN638-ZUCB CN11 for proper connection, and correct as necessary. 4 MS601 I/O check, sensor check ZUCB CN11-9 ZU-606 8-C. 5 M608 operation check ZUCB CN11-8 (DRV) ZU-606 7 to 8-C. 6 Replace M608. 7 ZUCB ICP9 conduction check. 8 Replace ZUCB. |
| Error code: | C1140 |
| Description: | PF lift motor error Object: Side feeder |
| Causes: | 1. The PF lift upper limit sensor does not turn on when passing 30s after cassette 5 is inserted. 2. The lock-up signal is detected for 200ms continuously during the PF lift motor operation. 3. The PF lift upper limit sensor does not turn on when passing 2s after the upper limit control when printing starts. |
| Remedy: | 1 Checking the bottom plate The bottom plate does not operate properly. Repair or replace the bottom plate when it does not move vertically. 2 Checking the drive gear The drive gear to lift up the bottom plate does not rotate properly. Check if the drive gears to lift up the bottom plate rotate smoothly or have no excessive load. And apply the grease to the frictional parts and fix the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor - PF main PWB Wiring diagram 4 Checking the PF lift motor The PF lift motor is faulty. Replace the PF lift motor. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift upper limit sensor - PF main PWB Wiring diagram 6 Checking the PF lift upper limit sensor The PF lift upper limit sensor is not properly attached or faulty. Reattach the PF lift upper limit sensor. Then, replace it if it is not fixed. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1141 |
| Description: | FNS paddle motor’s malfunction. <When FS-536 or FS-536SD is installed> The upper paddle home position detection sensor (PS14) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M5) is turning. <When FS-537 or FS-537SD is installed> The paddle home sensor (PS25) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M9) is turning. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS paddle motor (M5) • Upper paddle home position detection sensor (PS14) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • FNS paddle motor (M9) • Paddle home sensor (PS25) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M5-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS14-FSCB J4 for proper connection and correct as necessary. 4. PS14 I/O check, sensor check • Control signal: FSCB J4<B>-7 (ON) • Location of electrical component: FS-536/FS-536SD 15-C 5. M5 operation check • Control signal: FSCB J4<A>-9 to 12 • Location of electrical component: FS-536/FS-536SD 14-C 6. Replace M5. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M9-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS25-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 4. PS25 I/O check, sensor check • Control signal: FSCB J14<B>-10 (ON) • Location of electrical component: FS-537/FS-537SD 16-K to L 5. M9 operation check • Control signal: FSCB J14<B>-4 to 7 • Location of electrical component: FS-537/FS-537SD 17- K to L 6. Replace M9. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1142 |
| Description: | Paddle up/down motor`s drive malfunction. <When FS-537 or FS-537SD is installed> The paddle up/down home sensor (PS27) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the paddle up/down motor (M7) is energized. |
| Causes: | • Paddle up/down motor (M7) • Paddle up/down home sensor (PS27) • FS control board (FSCB) |
| Remedy: | (2) Procedure 1. Check the connector between M7-relay CN13<A>-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS27-relay CN13<A>-FSCB J14 for proper connection and correct as necessary. 4. PS27 I/O check, sensor check • Control signal: FSCB J14<A>-7 (ON) • Location of electrical component: FS-537/FS-537SD 18-K to L 5. M7 operation check • Control signal: FSCB J14<A>-1 to 4 • Location of electrical component: FS-537/FS-537SD 18-K to L 6. Replace M7. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1143 |
| Description: | Arm drive motor’s drive malfunction. <When FS-537 or FS-537SD is installed> The arm home position sensor (PS26) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the arm drive motor (M8) is energized. |
| Causes: | • Arm drive motor (M8) • Arm home position sensor (PS26) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M8-relay CN13<A>-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M8 for proper drive coupling and correct as necessary. 3. Check the connector between PS26-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 4. PS26 I/O check, sensor check • Control signal: FSCB J14<B>-3 (ON) • Location of electrical component: FS-537/FS-537SD 17-K to L 5. M8 operation check • Control signal: FSCB J14<A>-8 to 11 • Location of electrical component: FS-537/FS-537SD 17-K to L 6. Replace M8. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1144 |
| Description: | Pre-eject drive motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • The pre-eject home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the preeject drive motor (M9) is turned ON. • The pre-eject away sensor (PS22) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the preeject drive motor (M9) is turned ON. <When FS-537 or FS-537SD is installed> The trail edge stopper home sensor (PS31) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the pre-eject drive motor (M2) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Pre-eject drive motor (M9) • Pre-eject home sensor (PS21) • Pre-eject away sensor (PS22) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Pre-eject drive motor (M2) • Trail edge stopper home sensor (PS31) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M9-relay CN7<A>-FSCB J13 for proper connection, and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 4. Check the connector between PS22-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 5. PS21 I/O check, sensor check • Control signal: FSCB J12-6 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 6. PS22 I/O check, sensor check • Control signal: FSCB J12-9 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 7. M9 operation check • Control signal: FSCB J13-3 to 4 • Location of electrical component: FS-536/FS-536SD 9-C 8. Replace M9. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M2-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS31-relay CN2-relay CN1<B>-FSCB J22 for proper connection and correct as necessary. 4. PS31 I/O check, sensor check • Control signal: FSCB J22<B>-13 • Location of electrical component: FS-537/FS-537SD 3-D 5. M2 operation check • Control signal: FSCB J22<A>-3 to 4 • Location of electrical component: FS-537/FS-537SD 1-D 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1145 |
| Description: | Trailing edge stopper motor malfunction. <When FS-536 or FS-536SD is installed> The trailing edge stopper home position detection sensor (PS20) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the trailing edge stopper motor (M6) is turned ON. <When FS-537 or FS-537SD is installed> The trailing edge stopper home position detection sensor/F (PS10) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the trailing edge stopper motor/F (M12) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Trailing edge stopper motor (M6) • Trailing edge stopper home position detection sensor (PS20) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Trail edge stopper motor/F (M12) • Trail edge stopper sensor/F (PS10) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M6-FSCB J5 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS20-relay CN19-FSCB J5 for proper connection and correct as necessary. 4. PS20 I/O check, sensor check • Control signal: FSCB J5-9 (ON) • Location of electrical component: FS-536/FS-536SD 15-K 5. M6 operation check • Control signal: FSCB J5-13 to 16 • Location of electrical component: FS-536/FS-536SD 15-K 6. Replace M6. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M12-relay CN5-FSCB J18 for proper connection and correct as necessary. 2. Check the connector of M12 for proper drive coupling and correct as necessary. 3. Check the connector between PS10-relay CN5-FSCB J18 for proper connection and correct as necessary. 4. PS10 I/O check, sensor check • Control signal: FSCB J18-13 (ON) • Location of electrical component: FS-537/FS-537SD 6 to 7-D 5. M12 operation check • Control signal: FSCB J18-14 to 17 • Location of electrical component: FS-537/FS-537SD 7-D 6. Replace M12. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1150 |
| Description: | Side feeder lift motor going down error (optional side feeder) • Lower limit detection switch does not turn off within 15 s of the side feeder lift motor starting (within 200 ms during paper feeding). This error is detected four times successively. |
| Causes: | Poor contact of lower limit detection switch connector terminals. Defective side feeder main PWB. Defective side feeder lift motor. |
| Remedy: | Poor contact of lower limit detection switch connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective side feeder main PWB. Replace the side feeder main PWB. Defective side feeder lift motor. Run maintenance mode U247 and measure the voltage between terminals YC5-A12 (side-feeder main circuit board) and YC6- B11. (Make sure all of LUSSW, UCSSW, LLSSW and RCSSW are off.) Despite either DC24V or DC-24V is observed but if the side-feeder lift motor does not operate, replace the side-feeder lift motor. |
| Error code: | C1151 |
| Description: | Center-staple stapler drive motor malfunction <When FS-526+SD-508 is installed> • The stapler home sensor (PS33) is turned neither ON nor OFF even after the set period of time has elapsed after the center staple motor (M23) is turned ON. |
| Causes: | Center staple motor (M23) Stapler home sensor (PS33) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M23 for proper drive coupling, and correct as necessary. - - 3 PS33 I/O check, sensor check SDDB CN403-17 (ON) SD-508 C-10 4 M23 operation check SDDB CN406<A>-1 to 4 (ON) SD-508 K-8 5 Change M23 - - 6 SDDB ICP4 conduction check - - 7 Change SDDB - - 8 Change FSCB |
| Error code: | C1152 |
| Description: | Paper transport belt motor`s malfunction. <When FS-537SD is installed> Even after a predetermined period of time has elapsed since the paper transport belt motor (M34) starts operation, the lock signal is not set to L (turning). |
| Causes: | • Paper transport belt motor (M34) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M34-relay CN21-FSCB J24for proper connection and correct as necessary. 2. Check the connector of M34 for proper drive coupling and correct as necessary. 3. M34 operation check • Control signal: FSCB J24-1 to 11 • Location of electrical component: FS-537/FS-537SD 7-M 4. Replace M34. 5. Replace SDCB. 6. FSCB F4 conduction check 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1153 |
| Description: | Center-staple paddle up-down motor malfunction <When FS-526+SD-508 is installed> • The paddle home sensor/C (PS37) is turned neither ON nor OFF even after the set period of time has elapsed after the center staple paddle lift motor/C (M26) is turned ON. |
| Causes: | Center staple paddle lift motor/C (M26) Paddle home sensor/C (PS37) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M26 for proper drive coupling, and correct as necessary. - - 3 PS37 I/O check, sensor check SDDB CN406<A>-11 (ON) SD-508 K-9 4 M26 operation check SDDB CN406<A>-5 to 8 SD-508 K-8 5 Change M26 - - 6 SDDB ICP4 conduction check - - 7 Change SDDB - - 8 Change FSCB |
| Error code: | C1156 |
| Description: | SD paddle motor malfunction. <When FS-536SD or FS-537SD is installed> The paddle home sensor (PS5) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the SD paddle motor (M7) is turning. |
| Causes: | <When FS-536SD or FS-537SD is installed> • SD paddle motor (M7) • Paddle home sensor (PS5) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M7-SDCB J8 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS5-SDCB J8 for proper connection and correct as necessary. 4. PS5 I/O check, sensor check • Control signal: SDCB J8-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 5. M7 operation check • Control signal: SDCB J8-4 to 7 • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 6. Replace M7. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1157 |
| Description: | Center-staple paddle roller motor malfunction (middle) <When FS-526+SD-508 is installed> • The center staple paddle/C (M30) lock signal remains set to L for a set period of time while the center staple paddle/C (M30) is turning. |
| Causes: | Center staple paddle/C (M30) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M30 for proper drive coupling, and correct as necessary. - - 3 M30 operation check SDDB CN406<B>-11 to 15 SD-508 K-10 4 Change M30 - - 5 SDDB ICP5 conduction check - - 6 Change SDDB - - 7 Change FSCB |
| Error code: | C1158 |
| Description: | Center-staple paddle roller motor malfunction (leading edge) <When FS-527+SD-509 is installed>• Even after the set period of time has elapsed after the lower paddle motor (M22) starts running, a change of motor lock signal is not detected and neither the paper detection sensor/1 (PS43) nor the paper detection sensor/2 (PS44) is turned ON. |
| Causes: | lower paddle motor (M22) Paper detection sensor/1 (PS43) Paper detection sensor/2 (PS44) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M22 for proper drive coupling, and correct as necessary. - - 3 PS43 I/O check, sensor check SDDB PJ9-8 (ON) SD-509 G-1 4 PS44 I/O check, sensor check SDDB PJ13-2 (ON) SD-509 G-3 5 M22 operation check SDDB PJ5-1 to 5 SD-509 B-4 6 Change M22 - - 7 Change SDDB - - 8 Change FSCB |
| Error code: | C1182 |
| Description: | Unsupported option trouble |
| Causes: | When JS-504 is installed: Shift motor (M2) Shift home sensor (PS6) JS control board (JSCB). When FS-527 is installed: Tray2 shift motor (M16) Tray2 shift home sensor (PS25) FS control board (FSCB) |
| Error code: | C1183 |
| Description: | Finishing option elevator drive malfunction |
| Causes: | Elevate motor (M15) Tray1 lower position sensor (PS21) Tray1 upper position sensor (PS24) Tray1 upper position switch (SW2) Tray1 lower position switch (SW3) FS control board (FSCB) |
| Error code: | C1190 |
| Description: | Finishing option aligning bar moving mechanism malfunction 1 |
| Causes: | Alignment plate motor (M13) Alignment plate home sensor (PS17) FS control board (FSCB) |
| Error code: | C1194 |
| Description: | Leading edge stopper motor drive malfunction <When FS-527 is installed> • The leading edge stopper home sensor (PS20) is turned neither ON nor OFF even after the set period of time has elapsed after the leading edge stopper motor (M14) is turned ON. |
| Causes: | Leading edge stopper motor (M14) Leading edge stopper home sensor (PS20) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M13 for proper drive coupling, and correct as necessary. - - 3 PS17 I/O check, sensor check FSCB PJ17-6 (ON) FS-527 B to C-8 4 M13 operation check FSCB PJ8-9 to 12 FS-527 B to C-6 5 Change M13 - - 6 Change FSCB |
| Error code: | C11A1 |
| Description: | Finishing option exit roller pressure/retraction failure |
| Causes: | Exit roller retraction motor (M9) Exit roller pressure sensor (PS12) FS control board (FSCB) |
| Error code: | C11A2 |
| Description: | Saddle exit roller pressure/retraction failure |
| Causes: | <When FS-536 or FS-536SD is installed> • Receiving roller retraction motor (M4) • Receiving roller retraction sensor (PS11) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Receiving roller retraction motor (M10) • Receiving roller retraction sensor (PS22) • FS control board (FSCB) |
| Error code: | C11A7 |
| Description: | Tray 3 exit roller pressure/ retraction malfunction <When JS-603 is installed> • The exit roller pressure sensor (PS12) is turned neither ON nor OFF even after the set period of time has elapsed after the exit roller retraction motor (M9) is turned ON. |
| Causes: | Tray3 exit roller retraction motor (M17) Tray3 exit roller retraction sensor (PS35) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M17 for proper drive coupling, and correct as necessary. - - 3 PS35 I/O check, sensor check FSCB PJ12-6 (ON) FS-527 (JS-603) L-10 4 M17 operation check FSCB PJ30-2 (REM) FS-527 (JS-603) L-9 5 Change M17 - - 6 Change FSCB |
| Error code: | C11B0 |
| Description: | Finishing option stapler unit CD drive failure |
| Causes: | Stapler movement motor (M11) Stapler home sensor/1 (PS18) Stapler home sensor/2 (PS19) FS control board (FSCB) |
| Error code: | C11B2 |
| Description: | Finishing option stapling mechanism malfunction 1 |
| Causes: | Stapler unit FS control board (FSCB) |
| Error code: | C11B5 |
| Description: | Side staple 1 drive failure |
| Causes: | Saddle stapler unit SD drive board (SDDB) FS control board (FSCB) |
| Error code: | C11C0 |
| Description: | Punch motor malfunction |
| Causes: | Punch motor/1 (M100) Punch home sensor/1 (PS100) FS control board (FSCB) |
| Error code: | C11E0 |
| Description: | Unsupported option trouble |
| Causes: | When FS-527 is installed: Duplex path switching motor (M2) Duplex path switching sensor (PS3)FS control board (FSCB). When JS-504 is installed: Route change motor (M3) Route change home sensor (PS4) JS control board (JSCB) |
| Error code: | C11E1 |
| Description: | Paper exit switching drive malfunction. <When FS-536 or FS-536SD is installed> The exchange folded paper output sensor (PS30) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the FNS entry transport motor (M2) is turned ON. <When FS-537 or FS-537SD is installed> The route change gate home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the route change gate motor (M4) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS entry transport motor (M2) • Exchange folded paper output sensor (PS30) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Route change gate motor (M4) • Route change gate home sensor (PS21) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M2-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS30-FSCB J4 for proper connection and correct as necessary. 4. PS30 I/O check, sensor check • Control signal: FSCB J4<A>-15 (ON) • Location of electrical component: FS-536/FS-536SD 14-C 5. M2 operation check • Control signal: FSCB J9<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 12-C 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M4-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-FSCB J12 for proper connection and correct as necessary. 4. PS21 I/O check, sensor check • Control signal: FSCB J12<B>-12 (ON) • Location of electrical component: FS-537/FS-537SD 18-D 5. M4 operation check • Control signal: FSCB J21<B>-8 to 9 • Location of electrical component: FS-537/FS-537SD 18-D 6. Replace M4. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C11E2 |
| Description: | Paper exit switching (JS) drive malfunction. <When FS-537 or FS-537SD is installed> The sub tray/JS route change gate home sensor (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the sub tray discharge motor (M18) is turned ON. |
| Causes: | • Sub tray discharge motor (M18) • Sub tray/JS route change gate home sensor (PS23) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M18-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M18 for proper drive coupling and correct as necessary. 3. Check the connector between PS23-FSCB J12 for proper connection and correct as necessary. 4. PS23 I/O check, sensor check • Control signal: FSCB J12<A>-16 (ON) • Location of electrical component: FS-537/FS-537SD 17-D 5. M18 operation check • Control signal: FSCB J12<A>-5 to 6 • Location of electrical component: FS-537/FS-537SD 16-D 6. Replace M18. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C2101 |
| Description: | Developer motor error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking the developer motor The developer motor drive is faulty. Execute U030 [DLP(K)] and check the developer motor K operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 5 Checking the developer motor The developer motor is not properly attached or faulty. Reattach the developer motor. If not repaired, replace the motor. Detaching and reattaching the developer motor 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2151 |
| Description: | Secondary transfer roller pressure welding alienation • During a retraction operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its retracted position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. • During a pressure operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its pressed position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. |
| Causes: | • 2nd transfer pressure motor (M3) • 2nd transfer pressure sensor (PS50) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M11 connector for proper connection and correct as necessary. 2 Check the connector of M11 for proper drive coupling and correct as necessary. 3 PS36 I/O check PRCB CN3PRCB-9 (ON) D-5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C2152 |
| Description: | Transfer belt pressure welding alienation • During a retraction operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its retracted position within a predetermined period of time after the transfer belt retraction clutch is turned ON. • During a pressure operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its pressed position within a predetermined period of time after the transfer belt clutch is turned ON. |
| Causes: | • 1st transfer pressure sensor/K (PS51) • 1st transfer pressure sensor/YMC (PS52) • 1st transfer pressure motor (M21) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 PS31 I/O check PRCB CN36PRCB-15 (ON) D-26 to 27. 3 CL7 operation check PRCB CN39PRCB-10 (ON) D-23. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change CL7. 6 Change M5. 7 Change PRCB. |
| Error code: | C2160 |
| Description: | PC charge (C) malfunction When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined period of time. In this case, C2164 is displayed at the first detection and then after the trouble is reset, a leak IU identification process is executed. Then the trouble code corresponding to the IU color is displayed. |
| Causes: | • Imaging unit • High voltage unit/1 (HV1) • Printer control board (PRCB) |
| Remedy: | 1 Check the imaging unit for proper connection and correct as necessary. 2 Check the HV1 connector for proper connection and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Replace IU. 5 Replace HV1. 6 Replace PRCB. |
| Error code: | C2161 |
| Description: | PC charge (M) malfunction When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined period of time. In this case, C2164 is displayed at the first detection and then after the trouble is reset, a leak IU identification process is executed. Then the trouble code corresponding to the IU color is displayed. |
| Causes: | • Imaging unit • High voltage unit/1 (HV1) • Printer control board (PRCB) |
| Remedy: | 1 Check the imaging unit for proper connection and correct as necessary. 2 Check the HV1 connector for proper connection and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Replace IU. 5 Replace HV1. 6 Replace PRCB. |
| Error code: | C2162 |
| Description: | PC charge (Y) malfunction When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined period of time. In this case, C2164 is displayed at the first detection and then after the trouble is reset, a leak IU identification process is executed. Then the trouble code corresponding to the IU color is displayed. |
| Causes: | • Imaging unit • High voltage unit/1 (HV1) • Printer control board (PRCB) |
| Remedy: | 1 Check the imaging unit for proper connection and correct as necessary. 2 Check the HV1 connector for proper connection and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Replace IU. 5 Replace HV1. 6 Replace PRCB. |
| Error code: | C2163 |
| Description: | PC charge malfunction. When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined period of time. |
| Causes: | • Drum unit • High voltage unit/1 (HV1) • MFP board (MFPB) |
| Remedy: | 1. Check the drum unit for proper connection and correct as necessary. 2. Check the connector between HV1 CN1-MFPB CN9E for proper connection and correct as necessary. 3. Replace the drum unit. 4. Replace HV1. 5. Replace MFPB |
| Error code: | C2164 |
| Description: | PC charge malfunction • When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined period of time. |
| Causes: | • Imaging unit • High voltage unit/1 (HV1) • Printer control board (PRCB) |
| Remedy: | 1 Check the imaging unit for proper connection and correct as necessary. 2 Check the HV connector for proper connection and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Change IU. 5 Change HV. 6 Change PRCB. |
| Error code: | C2204 |
| Description: | Drum motor Y steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB Y at every 1s. |
| Remedy: | 1 Checking drum motor Y The drum motor Y drive is faulty. Execute U030 [Process] and check the drum motor Y operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor Y - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2253 |
| Description: | Color PC motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/YMC (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2254 |
| Description: | Color PC motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/YMC motor (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2255 |
| Description: | Developing motor’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Developing motor/YMC (M17) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M21-PRCB CN32 for proper connection and correct as necessary. 2 Check the M21 connector for proper drive coupling and correct as necessary. 3 M21 operation check PRCB CN32-2 (REM) PRCB CN32-5 (LOCK). bizhub C224 25-I to J 4 Replace M21. 5 Replace PRCB. |
| Error code: | C2256 |
| Description: | Developing motor’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Developing motor/YMC (M17) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M21-PRCB CN32 for proper connection and correct as necessary. 2 Check the M21 connector for proper drive coupling and correct as necessary. 3 M21 operation check PRCB CN32-2 (REM) PRCB CN32-5 (LOCK). bizhub C224 25-I to J 4 Replace M21. 5 Replace PRCB. |
| Error code: | C2257 |
| Description: | Cleaning brush motor’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Cleaning brush motor (M38) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M38-PRCB CN39 for proper connection and correct as necessary. 2 Check the M38 connector for proper drive coupling and correct as necessary. 4 M38 operation check PRCB CN39-1 to 7 20-K. 5 Replace M38. 6 PRCB ICP8 conduction check. 7 Replace PRCB. |
| Error code: | C2258 |
| Description: | Cleaning brush motor’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Cleaning brush motor (M38) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M38-PRCB CN39 for proper connection and correct as necessary. 2 Check the M38 connector for proper drive coupling and correct as necessary. 4 M38 operation check PRCB CN39-1 to 7 20-K. 5 Replace M38. 6 PRCB ICP8 conduction check. 7 Replace PRCB. |
| Error code: | C2259 |
| Description: | Developing motor/K’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Developing motor/K (M19) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M19-PRCB CN22 for proper connection and correct as necessary. 2 Check the M19 connector for proper drive coupling and correct as necessary. 3 M19 operation check PRCB CN22-1 to 5 16-K. 4 Replace M19. 5 PRCB ICP6 conduction check. 6 Replace PRCB. |
| Error code: | C225A |
| Description: | Developing motor/K’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Developing motor/K (M19) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M19-PRCB CN22 for proper connection and correct as necessary. 2 Check the M19 connector for proper drive coupling and correct as necessary. 3 M19 operation check PRCB CN22-1 to 5 16-K. 4 Replace M19. 5 PRCB ICP6 conduction check. 6 Replace PRCB. |
| Error code: | C225B |
| Description: | PC motor/K’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/K (M18) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M18-PRCB CN21 for proper connection and correct as necessary. 2 Check the M18 connector for proper drive coupling and correct as necessary. 3 M18 operation check PRCB CN21-13 (LOCK) PRCB CN21-10 (REM) 16-K. 4 Replace M18. 5 PRCB ICP6 or ICP18 conduction check. 6 Replace PRCB. |
| Error code: | C225C |
| Description: | PC motor/K’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/K (M18) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M18-PRCB CN21 for proper connection and correct as necessary. 2 Check the M18 connector for proper drive coupling and correct as necessary. 3 M18 operation check PRCB CN21-13 (LOCK) PRCB CN21-10 (REM) 16-K. 4 Replace M18. 5 PRCB ICP6 or ICP18 conduction check. 6 Replace PRCB. |
| Error code: | C2350 |
| Description: | Toner suction fan failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Toner suction fan (FM7) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM7-relay CN326-MFPB CN24E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM7 operation check • Control signal: MFPB CN24E-7 (DRIVE), MFPB CN24E-9 (LOCK) • Location of electrical component: 1-K 4. Replace FM7. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C2353 |
| Description: | IU cooling fan/out`s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • IU cooling fan /out (FM15) • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM15-PHRYB CN5 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM15 operation check • Control signal: PHRYB CN5-1 (DRIVE), PHRYB CN5-3 (LOCK) • Location of electrical component: 3-B 4. Replace FM15. 5. PHRYB F2 conduction check. 6. Replace PHRYB. 7. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C2354 |
| Description: | Rear side cooling fan motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | Rear side cooling fan motor (FM16) Printer control board (PRCB) |
| Remedy: | 1 Check the FM16 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM16 operation check PRCB CN18-2 (REM) PRCB CN18-3 (LOCK) C-12 to 13 4 Change FM16 - - 5 PRCB ICP7 conduction check - - 6 Change PRCB |
| Error code: | C2551 |
| Description: | Abnormally low toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2552 |
| Description: | Abnormally high toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2553 |
| Description: | Abnormally low toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2554 |
| Description: | Abnormally high toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2555 |
| Description: | Abnormally low toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2556 |
| Description: | Abnormally high toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2557 |
| Description: | Abnormally low toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Developing unit • Toner cartridge • Toner empty sensor/K (PZS/K) • Toner supply motor/K (M12) • Toner cartridge motor/CK (M14) • MFP board (MFPB) |
| Remedy: | 1 M3 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 D-23. 2 Reinstall imaging unit. 3 Reinstall toner cartridge. 4 Change imaging unit /K. 5 Change PRCB. |
| Error code: | C2558 |
| Description: | Abnormally high toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Developing unit • Toner cartridge • Sub hopper unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit /K. 4 Change PRCB. |
| Error code: | C2559 |
| Description: | Cyan TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255A |
| Description: | Magenta TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255B |
| Description: | Yellow TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255C |
| Description: | Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit /K. 2 Change imaging unit /K. 3 Change PRCB. |
| Error code: | C2561 |
| Description: | Cyan TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Developing unit /K • PH relay board (PHRYB) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall developing unit. 2 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16 for proper connection and correct as necessary. 3 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 4 Replace the developing unit. 5 Replace FRB. 6 Replace PRCB. |
| Error code: | C2562 |
| Description: | Magenta TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Developing unit /K • PH relay board (PHRYB) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall developing unit. 2 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16 for proper connection and correct as necessary. 3 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 4 Replace the developing unit. 5 Replace FRB. 6 Replace PRCB. |
| Error code: | C2563 |
| Description: | Yellow TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Developing unit /K • PH relay board (PHRYB) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall developing unit. 2 Check the connector between developing unit-FRB CN13, CN14, CN15, CN16 for proper connection and correct as necessary. 3 Check the connector between FRB CN1, CN3-PRCB CN7, CN9 for proper connection and correct as necessary. 4 Replace the developing unit. 5 Replace FRB. 6 Replace PRCB. |
| Error code: | C2564 |
| Description: | Black TCR sensor failure. • The TCR sensor input is 0. • This detection is used for detecting disconnection of TCR sensor connector. |
| Causes: | • Developing unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Check the connector between the developing unit-relay CN214-PHRYB CN6 for proper connection and correct as necessary. 3. Replace the developing unit. 4. PHRYB PS1 conduction check. 5. Replace PHRYB. 6. Replace MFPB |
| Error code: | C2650 |
| Description: | PF feed motor error (Side Multi Feeder) Object: Side multi feeder |
| Causes: | The ready signal is not at the L level (stable rotation) for passing 2s since the PF feed motor drive is started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected. The drive parts are faulty. Execute U247 [SMT] > [Motor On] to check the paper feeding operation. If the PF feed motor does not properly operate, reconnect the connector. Check if the PF feed roller and the drive gears rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. Executing U247 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF main PWB • PF main PWB - Engine PWB (Cable from the side multi feeder) Wiring diagram 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF drive unit (Side multi feeder) 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 5 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2651 |
| Description: | EEPROM access error (IU C) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2652 |
| Description: | EEPROM access error (IU M) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2653 |
| Description: | EEPROM access error (IU Y) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2654 |
| Description: | EEPROM access error (IU K) |
| Causes: | Imaging unit /C Imaging unit /M Imaging unit /Y Drum unit /K Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2A14 |
| Description: | Drum unit new release failure. The status with the new unit is not cleared after the new drum unit is set. |
| Causes: | • Drum unit • MFP board (MFPB) |
| Remedy: | 1. Clean the connection between the drum unit and the developing unit if dirty. 2. Reinstall the drum unit. 3. Check the harness for proper connection and correct as necessary. 4. Replace the drum unit. 5. Replace MFPB. |
| Error code: | C2A21 |
| Description: | Toner cartridge/C new release failure The status with the new cartridge is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/C • Toner cartridge/M • Toner cartridge/Y • Toner cartridge/K • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall the toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Replace the toner cartridge. 5 Replace PRCB. |
| Error code: | C2A22 |
| Description: | Toner cartridge/M new release failure The status with the new cartridge is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/C • Toner cartridge/M • Toner cartridge/Y • Toner cartridge/K • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall the toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Replace the toner cartridge. 5 Replace PRCB. |
| Error code: | C2A23 |
| Description: | Toner cartridge/Y new release failure The status with the new cartridge is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge/C • Toner cartridge/M • Toner cartridge/Y • Toner cartridge/K • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall the toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Replace the toner cartridge. 5 Replace PRCB. |
| Error code: | C2A24 |
| Description: | Toner cartridge new release failure. The status with the new unit is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge • MFP board (MFPB) |
| Remedy: | 1. Clean the connection between the toner cartridge and the machine if dirty. 2. Reinstall the toner cartridge. 3. Check the harness for proper connection and correct as necessary. 4. Replace the toner cartridge. 5. Replace MFPB. |
| Error code: | C3101 |
| Description: | Fusing roller separation failure • With the fusing roller being retracted, the pulse of the fusing roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • With the fusing roller being pressed, the pulse of the roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • During a pressure operation of the fusing roller, the fusing roller is not at the pressed position even after the roller retraction sensor counts the specified number of pulses after the fusing retraction motor starts rotating. |
| Causes: | • Fusing pressure home sensor (PS55) • Fusing pressure motor (M29) • Printer control board (PRCB) • Fusing unit |
| Remedy: | 1 Check the M12 connector for proper connection and correct as necessary. 2 PS38 I/O check PRCB CN28PRCB-8 (ON) D-25. 3 M12 operation check PRCB CN28PRCB-4 to 5 D-25. 4 Change M12. 5 Change fusing unit. 6 Change PRCB. |
| Error code: | C3102 |
| Description: | Heating roller failure to turn. During any state other than printing operation, the hard latch signal from one or both of the heating roller rotation latch detection 1 and the heating roller rotation latch detection 2 is turned ON. |
| Causes: | • Fusing unit • Fusing belt rotation sensor (PS56) (bizhub 958, bizhub PRO 958) • Heating roller rotation sensor (PS56) (bizhub 808/758) • Fusing motor (M30) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for proper connection and correct as necessary. 2. Check the connector between M30-MFPB CN16E for proper connection and correct as necessary. 3. Check the connector of M30 for proper drive coupling and correct as necessary. 4. Check the fusing unit-relay CN260-MFPB CN30E for proper connection and correct or change as necessary. 5. PS56 I/O check, sensor check • Control signal: MFPB CN30E-14 (ON) • Location of electrical component: 9-C, 12-C 6. M30 operation check • Control signal: MFPB CN16E-4 (REM), MFPB CN16E-7 (LOCK) • Location of electrical component: 10-K 7. Replace M30. 8. Replace the fusing unit. 9. MFPB F2E or F14E conduction check 10. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C3201 |
| Description: | Fusing motor failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3202 |
| Description: | Fusing motor turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3303 |
| Description: | Paper cooling fan/out`s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Paper cooling fan/out (FM13) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM13-relay CN323-MFPB CN27E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM13 operation check • Control signal: MFPB CN27E<B>-10 (DRIVE), MFPB CN27E<B>-12 (LOCK) • Location of electrical component: 16-C 4. Replace FM13. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C3304 |
| Description: | Switchback paper cooling fan/2`s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Switchback paper cooling fan/2 (FM5) • Paper feed/transport drive board (PFTDB) |
| Remedy: | 1. Check the connector between FM5-relay CN282-relay CN280-relay CN279-relay CN271B-PFTDB CN2 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM5 operation check. • Control signal: PFTDB CN2-18 (LOCK) • Location of electrical component: 5-P 4. Replace FM5. 5. PFTDB F14 conduction check 6. Replace PFTDB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C3305 |
| Description: | Switchback paper cooling fan/1`s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Switchback paper cooling fan/1 (FM4) • Paper feed/transport drive board (PFTDB) |
| Remedy: | 1. Check the connector between FM4-relay CN283-relay CN280-relay CN279-relay CN271B-PFTDB CN2 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM4 operation check • Control signal: PFTDB CN2-15 (LOCK) • Location of electrical component: 5-P 4. Replace FM4. 5. PFTDB F14 conduction check 6. Replace PFTDB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C3424 |
| Description: | Fusing heaters trouble (soaking side) • After warm-up operation starts, the soaking roller thermistor does not detect a temperature as high as a predetermined one though a predetermined period of time has elapsed. |
| Causes: | Fusing unit IH power supply (IHPU) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, MFPB and DCPU for proper connection and correct or change as necessary. - - 4 Change fusing unit - - 5 Change IHPU - - 6 Change PRCB - - 7 Change DCPU |
| Error code: | C3425 |
| Description: | Fusing warm-up trouble. bizhub 958, bizhub PRO 958: • After warm-up operation starts, the fusing belt temperature sensor/1 (TEMS1) does not detect a temperature increasing to a predetermined one though a predetermined period of time has elapsed. • From the start of warm-up operation, it does not terminate within a predetermined period of time. b izhub 808/758: • After warm-up operation starts, the heating roller temperature sensor/1 (TEMS1) does not detect a temperature increasing to a predetermined one though a predetermined period of time has elapsed. • From the start of warm-up operation, it does not terminate within a predetermined period of time. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Check the connector between NF1 CN2-IHPU CN1 for proper connection and correct as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Replace the fusing unit. 8. Replace IHPU. 9. MFPB IC80E conduction check 10. Replace MFPB. 11. Replace NF1. |
| Error code: | C3721 |
| Description: | Fusing abnormally high temperature detection (heating side) • The heating roller thermistor continues to detect a temperature higher than a predetermined one for a predetermined period of time. • Hard protection signal L is detected continuously over a predetermined period of time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3722 |
| Description: | Fusing abnormally high temperature detection (Edge of the heating side) Detected temperature of the heating roller thermistor/1 (TH1) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3724 |
| Description: | Fusing abnormally high temperature detection (soaking side) • The soaking roller thermistor/1 continues to detect a temperature higher than a predetermined one for a predetermined period of time. • The signal is turned ON to activate the hard ratchet on the soaking side. |
| Causes: | Fusing unit IH power supply (IHPU) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, MFPB and DCPU for proper connection and correct or change as necessary. - - 4 Change fusing unit - - 5 Change IHPU - - 6 Change PRCB - - 7 Change DCPU |
| Error code: | C3725 |
| Description: | Fusing abnormally high temperature detection (Main of the heating side) • Detected temperature of the heating roller temperature sensor (TEMS) goes beyond a given temperature for a given period of time consecutively. • The hard protector signal error is detected for a given period of time consecutively. |
| Causes: | • Fusing unit • Heating roller temperature sensor (TEMS2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3822 |
| Description: | Fusing abnormally low temperature detection (Edge of the heating roller) The heating roller thermistor/3 continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, IHPU, NF1 and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace IHPU. 6 Replace PRCB. 7 Replace NF1. |
| Error code: | C3824 |
| Description: | Fusing abnormally low temperature detection (soaking side) • The soaking roller thermistor/1 continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | Fusing unit IH power supply (IHPU) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, PRCB and DCPU for proper connection and correct or change as necessary. - - 4 Change fusing unit - - 5 Change IHPU - - 6 Change PRCB - - 7 Change DCPU |
| Error code: | C3825 |
| Description: | Fusing abnormally low temperature detection (Main of the heating roller) The heating roller temperature sensor (TEMS) continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller temperature sensor (TEMS2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 PRCB ICP15 conduction check. 6 Replace PRCB. |
| Error code: | C3921 |
| Description: | Fusing sensor wire breaks detection (Center of the heating roller) • At the warm-up stage, the heating roller temperature sensor/2 voltage does not decrease by predetermined steps (temperature rise) within a predetermined time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, PRCB and REDB for proper connection and correct or change as necessary. - - 4 Change TEMS1, TEMS2 or TEMS3 - - 5 Change fusing unit - - 6 Change IHPU - - 7 PRCB ICP17 conduction check - - 8 Change PRCB - - 9 Change REDB |
| Error code: | C3922 |
| Description: | Fusing sensor wire breaks detection (Edge of the heating roller) After a predetermined period of time after the warm-up stage is started, the heating roller thermistor/1 (TH1) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3924 |
| Description: | Fusing sensor wire breaks detection (soaking side) • At the warm-up stage, the soaking roller thermistor/1 voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | Fusing unit IH power supply (IHPU) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, PRCB and DCPU for proper connection and correct or change as necessary. - - 4 Change fusing unit - - 5 Change IHPU - - 6 Change PRCB - - 7 Change DCPU |
| Error code: | C3925 |
| Description: | Fusing sensor wire breaks detection (Center of the heating roller) After a predetermined period of time after the warm-up stage is started, the heating roller temperature sensor (TEMS) voltage does not increase by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller temperature sensor (TEMS2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C392A |
| Description: | Fusing belt temperature sensor/1 contamination (Middle of the heating roller) (bizhub 958) Heating roller temperature sensor contamination (Middle of the heating roller (bizhub 808/758)bizhub 958, bizhub PRO 958: During waiting after a predetermined period of time after the warm-up stage terminates, the temperature detected by the fusing belt thermistor/1 (TH1) exceeds that detected by the fusing belt temperature sensor/1 (TEMS1) above a predetermined temperature, and this state continues for a predetermined period of time. bizhub 808/758: During waiting after a predetermined period of time after the warm-up stage terminates, the temperature detected by the heating roller thermostat/1 (TH1) exceeds that detected by the heating roller temperature sensor/1 (TEMS1) above a predetermined temperature, and this state continues for a predetermined period of time. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • Fusing belt thermistor/1 (TH1) (bizhub 958, bizhub PRO 958) • Heating roller thermostat/1 (TH1) (bizhub 808/758) • IH power supply unit (IHPU) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1. Wipe the TEMS1 clean of dirt if any. • Clear away a dirt or a foreign object on the sensor with a cotton swab. • When a dirt is left even if you cleaned the sensor by above procedure, clear away a dirt or a foreign object on the sensor using a cotton swab dampened with the alcohol. And, wipe off the sensor with a dry cotton swab afterwards. 2. Check the TEMS1 for installed position and proper connector connection. 3. Check the TH1 for installed position and proper connector connection. 4. Check the connection of the fusing unit. 5. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Check the connector between DCPU CN009-MFPB CN31E for proper connection and correct as necessary. 8. Replace the fusing unit. 9. Replace MFPB. |
| Error code: | C3B02 |
| Description: | IH malfunction (CPU) A failure in communication with the fusing CPU continues for a predetermined period of time. |
| Causes: | • Fusing unit • IH coil unit • IH power supply (IHPU) • IH magnetic erasing board (IHMEB) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, IH coil unit, IHPU, IHMEB, NF1 and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace the IH coil unit. 6 Replace IHPU. 7 Replace IHMEB. 8 PRCB ICP5 conduction check. 9 Replace PRCB. 10 Replace NF1. |
| Error code: | C3B03 |
| Description: | IH malfunction (monitor) • Though the IH heater is ON, this status cannot be detected mechanically. (IH heater operation failure) • Though the IH heater is OFF, mechanically, the ON status is detected. (Malfunction of IH heater operation) |
| Causes: | • Fusing unit • IH coil unit • IH magnetic erasing board (IHMEB) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, IH coil unit, IHPU, IHMEB, NF1 and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace the IH coil unit. 6 Replace IHPU. 7 Replace IHMEB. 8 PRCB ICP5 conduction check. 9 Replace PRCB. 10 Replace NF1. |
| Error code: | C3B05 |
| Description: | IH temperature sensor defect • While the IH heater was on, IH temperature sensor was disconnected for more than the predetermined period of time. • While the IH heater was on, short circuit on IH temperature sensor continued for more than the predetermined period of time. • While the IH heater was on, temperature change occurred within the predetermined period of time with over the predetermined range, and they continued for more than the predetermined period of time. • While the IH heater was on, temperature around the heat radiator stayed high for over the predetermined period of time. |
| Causes: | IH coil unit IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the connection of the fusing unit. - - 2 Check the fusing unit, degaussing coil unit, IHPU, PRCB and REDB for proper connection and correct or change as necessary. - - 3 Change degaussing coil unit - - 4 Change IHPU - - 5 Change PRCB - - 6 Change REDB |
| Error code: | C3B06 |
| Description: | IH surge error • While the IH heater was on, IH stopped due to input voltage which exceeded that of surge detection voltage, and the surge detection voltage continued for more than the predetermined period of time. |
| Causes: | IH coil unit IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the connection of the fusing unit. - - 2 Check the fusing unit, degaussing coil unit, IHPU, PRCB and REDB for proper connection and correct or change as necessary. - - 3 Change degaussing coil unit - - 4 Change IHPU - - 5 Change PRCB - - 6 Change REDB |
| Error code: | C3B07 |
| Description: | IH input power error • While the IH heater was ON, input power stayed at the high voltage power detection value or over for more than the predetermined period of time. • While the IH heater was ON, input power was at the low power detection value or under for more than the predetermined period of time. • While the IH heater was ON, input power was at the high voltage detection value or over for more than the predetermined period of time. • While the IH heater was ON, input power was below the low voltage detection value or under for more than the predetermined period of time. • While the IH heater was ON, inverter power stayed at the upper limit value or over for more than the predetermined period of time. • While the IH heater was ON, output voltage halt was detected. |
| Causes: | • IH coil unit • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connection of the fusing unit. 2 Check the fusing unit, IH coil unit, IHPU, NF1 and PRCB for proper connection and correct or change as necessary. 3 Replace the IH coil unit. 4 Replace IHPU. 5 Replace PRCB. 6 Replace NF1. |
| Error code: | C3B08 |
| Description: | IH input voltage error • While the IH heater was ON, input power was at the high voltage detection value or over for more than the predetermined period of time. • While the IH heater was ON, input voltage was at the low power detection value or under for more than the predetermined period of time. |
| Causes: | • IH coil unit • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connection of the fusing unit. 2 Check the fusing unit, IH coil unit, IHPU, NF1 and PRCB for proper connection and correct or change as necessary. 3 Replace the IH coil unit. 4 Replace IHPU. 5 Replace PRCB. 6 Replace NF1. |
| Error code: | C4101 |
| Description: | BD initialization error |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4301 |
| Description: | PH cooling fan’s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • PH cooling fan (FM14) • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM14-relay CN202-PHRYB CN4 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM14 operation check • Control signal: PHRYB CN4-8 (DRIVE), PHRYB CN4-9 (LOCK) • Location of electrical component: 6-B, 7-B 4. Replace FM14. 5. PHRYB F2 conduction check. 6. Replace PHRYB. 7. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C4501 |
| Description: | Laser malfunction. • SOS signal is not detected even after the lapse of a given period of time after starting the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Causes: | • PH unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between the PH unit-PHRYB CN8 for proper connection and correct as necessary. 2. Replace the PH unit. 3. PHRYB IC5 conduction check. 4. Replace PHRYB. 5. Replace MFPB. |
| Error code: | C5104 |
| Description: | Main high-voltage error Y |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5105 |
| Description: | Transfer belt motor`s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary |
| Causes: | • Transfer belt motor (M1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M1-PRCB CN21 for proper connection and correct as necessary. 2 Check the transfer belt for proper drive coupling and correct as necessary. 3 M1 operation check PRCB CN21-3 (REM) PRCB CN21-6 (LOCK) 17-K. 4 Replace M1. 5 PRCB ICP7 or ICP18 conduction check. 6 Replace PRCB. |
| Error code: | C5304 |
| Description: | Cleaning lamp Y error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp Y. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the sub front PWB and the connector of the drum unit Y, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp Y. Replace the drum unit Y. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C5306 |
| Description: | IH coil cooling fan’s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • IH coil cooling fan (FM11) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM11-relay CN324-MFPB CN24E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM11 operation check • Control signal: MFPB CN24E-1 (DRIVE), MFPB CN24E-3 (LOCK) • Location of electrical component: 1-K 4. Replace FM11. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C5351 |
| Description: | Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • DC power supply cooling fan (FM9) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1 Check the FM5 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check PRCB CN30PRCB-11 (ON) PRCB CN30PRCB-12 (LOCK) K-8. 4 Change FM5. 5 Change DCPU. 6 Change PRCB. |
| Error code: | C5354 |
| Description: | Exhaust fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Ozone ventilation fan (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM4 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM4 operation check PRCB CN3PRCB-14 (ON) PRCB CN3PRCB-16 (LOCK) D-6. 4 Change FM4. 5 Change PRCB. |
| Error code: | C5356 |
| Description: | Cooling fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | Cooling fan motor (FM3) Printer control board (PRCB) |
| Remedy: | 1 Check the FM3 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM3 operation check PRCB CN15-4 (REM) PRCB CN15-6 (LOCK) K-7 to 8 4 Change FM3 - - 5 PRCB ICP6 conduction check - - 6 Change MFPB |
| Error code: | C5370 |
| Description: | Rear side cooling fan’s failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan remains stationary. |
| Causes: | • MFP control board cooling fan (FM17) • MFP board (MFPB) |
| Remedy: | 1 Check the connector between FM3-MFPB PJ26 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM3 operation check MFPB PJ26 (LOCK) 7-P. 4 Replace FM3. 5 Replace MFPB. |
| Error code: | C5372 |
| Description: | MFP control board CPU temperature failure. Temperature failure of CPU on the MFP board was detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Reboot the machine. 2. Check for clogging in the ventilation path between the MFPB and the power supply cooling fan, and correct as necessary. 3. Replace MFPB. |
| Error code: | C6001 |
| Description: | DF related configuration error 1. Inconsistency in the configuration with the installed DF is detected on the main body. |
| Causes: | • DF control board (DFCB) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1. Check the type of the installed DF and replace it if it is a wrong one. 2. Correct the harness connection between DFCB CN12-relay CN47-MFPB CN1E if faulty. 3. Correct the harness connection between DSIPB CN1-MFPB CN24 if faulty. 4. Replace DFCB. 5. Replace DSIPB. 6. Replace MFPB. |
| Error code: | C6002 |
| Description: | DF related configuration error 2. Inconsistency in the configuration with the installed DF is detected on the DF. |
| Causes: | • DF control board (DFCB) • Dual scan image processing board (DSIPB) |
| Remedy: | 1. Check the type of the installed DF and replace it if it is a wrong one. 2. Correct the harness connection between DFCB CN12-relay CN47-MFPB CN1E if faulty. 3. Correct the harness connection between DSIPB CN1-MFPB CN24 if faulty. 4. Check the connectors of the dual scan image processing board (DSIPB) for proper connection, and correct as necessary. (Direction of the point of contact and connection state of the flat cable in particular) |
| Error code: | C6102 |
| Description: | Drive system home sensor malfunction • The scanner home sensor (PS201) is unable to detect the scanner located at its home position. • The scanner home sensor (PS201) is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor (PS201) detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor (PS201). |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6103 |
| Description: | Slider over running The scanner home sensor (PS201) detects the scanner at its home position during a period of time that begins with the time when a prescan command and a scan preparation command are executed and ends when a home return command is executed. |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6104 |
| Description: | Back side cleaning home sensor abnormality (initial) <When DF-701 is installed> • The CIS cleaning sensor (PS7) does not change from H to L even after the lapse of a given period of time after the home position detecting operation is started at the initial operation. • The CIS cleaning sensor (PS7) does not change from L to H even after the lapse of a given period of time after the home position detecting operation is started at the initial operation. |
| Causes: | • Back side cleaning home sensor (PS9) • Back side cleaning motor (M7) • DF control board (DFCB) |
| Remedy: | 1 Check if the opening and closing guide is firmly closed. 2 Check the connector between M5-DFCB J9 for proper connection, and correct as necessary. 3 Check the connector of M5 for proper drive coupling, and correct as necessary. 4 Check the connector between PS7-DFCB J13 for proper connection, and correct as necessary. 5 PS7 I/O check, sensor check DRCB J13-3 (ON) DF-701 1-G. 6 M5 operation check DRCB J9-1 to 4 DF-701 6-G. 7 Replace M5. 8 Replace DFCB. |
| Error code: | C6105 |
| Description: | Back side cleaning home sensor abnormality (normal) <When DF-701 is installed> At the time of operation other than the initial operation, the CIS cleaning sensor (PS7) error is detected. |
| Causes: | • Back side cleaning home sensor (PS9) • Back side cleaning motor (M7) • DF control board (DFCB) |
| Remedy: | 1 Check if the opening and closing guide is firmly closed. 2 Check the connector between M5-DFCB J9 for proper connection, and correct as necessary. 3 Check the connector of M5 for proper drive coupling, and correct as necessary. 4 Check the connector between PS7-DFCB J13 for proper connection, and correct as necessary. 5 PS7 I/O check, sensor check DRCB J13-3 (ON) DF-701 1-G. 6 M5 operation check DRCB J9-1 to 4 DF-701 6-G. 7 Replace M5. 8 Replace DFCB. |
| Error code: | C6301 |
| Description: | Optical cooling fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | Optical cooling fan motor (M202) Scanner relay board (REYB/SCAN) MFP board (MFPB) |
| Remedy: | 1 Check the FM201 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 M202 operation check REYB/SCAN PJ4-3 (LOCK) P-18 4 Change REYB/SCAN - - 5 Change MFPB |
| Error code: | C6303 |
| Description: | CIS cooling fan motor’s failure to turn • While the motor is running, the fan lock signal remains HIGH three times for a predetermined period of consecutive time. |
| Causes: | CIS Cooling fan motor (FM2) DF control board (DFCB) |
| Remedy: | 1 Check the FM2 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM2 operation check DFCB PJ12-4 to 6 DF-619 K-9 4 Change FM2 - - 5 DFCB ICP5 conduction check - - 6 Change DFCB |
| Error code: | C6704 |
| Description: | Image input time out. Image data is not input from the scanner to the MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Memory Bus Check] -> [Scanner -> Memory], and conduct the memory bus function. 2. Correct the harness connection between scanner section and MFPB if faulty. 3. MFPB F3E conduction check 4. Replace MFPB. 5. Replace the CCD unit. |
| Error code: | C6751 |
| Description: | CCD gain adjustment failure. • The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment. |
| Causes: | • LED exposure unit • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 2. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 3. Correct the harness connection between SCDB CN1-DCPU CN005 if faulty. 4. Check for possible extraneous light and correct as necessary. 5. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 6. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 7. Replace SCDB 8. Replace the CCD unit. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | C6752 |
| Description: | ASIC clock input error (front side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on CCD board (CCDB) was conducted, and verification failure was detected. |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Correct the harness connection of CCDB if faulty. 2. Replace the CCD unit. 3. MFPB F3E conduction check 4. Replace MFPB. |
| Error code: | C6753 |
| Description: | ASIC clock input error (back side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on dual scan image processing board (DSIPB) was conducted, and verification failure was detected. |
| Causes: | • CIS module (CIS) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CIS J101-DSIPB CN2 if faulty. 2. Correct the harness connection between DSIPB CN1-MFPB CN24 if faulty. 3. Replace CIS. 4. DFPU ICP1 conduction check. 5. Replace DSIPB. 6. MFPB F3E conduction check 7. Replace MFPB. |
| Error code: | C6754 |
| Description: | CIS clamp adjustment failure <When DF-701 is installed> After the gain adjustment is performed at the start-up, the CIS clamp adjustment value is too high or too low. |
| Causes: | • CIS module (CIS) • Dual scan image processing board (DSIPB) • DF power supply (DFPU) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection between CIS and DSIPB if faulty. 2 Correct the harness connection between CIS and CISPU if faulty. 3 Check for possible extraneous light and correct as necessary. 4 Clean the back side reading glass and the shading sheet if dirty. 5 Replace CIS. 6 Replace DSIPB. 7 Replace CISPU. 8 Replace MFPB. |
| Error code: | C6755 |
| Description: | CIS gain adjustment failure <When DF-701 is installed> After the gain adjustment is performed at the start-up, the peak value of the output data is lower than a given value. |
| Causes: | • CIS module (CIS) • Dual scan image processing board (DSIPB) • DF power supply (DFPU) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection between CIS and DSIPB if faulty. 2 Correct the harness connection between CIS and CISPU if faulty. 3 Check for possible extraneous light and correct as necessary. 4 Clean the back side reading glass and the shading sheet if dirty. 5 Replace CIS. 6 Replace DSIPB. 7 Replace CISPU. 8 Replace MFPB. |
| Error code: | C6901 |
| Description: | DSC board mount failure 1 When MFP detects that DSC board/1 (front side) is not properly installed. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6902, C6903 |
| Description: | DSC Bus check NG1 • When DSC bus check (front side) detects an error. |
| Causes: | DSC board (SC-507) MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSC board if faulty. - - 2 Change DSC board - - 3 Change MFPB |
| Error code: | C6911 |
| Description: | DSC board mount failure 2 <When DF-701 is installed> When MFP detects that DSC board/2 (back side) is not properly installed. |
| Causes: | • DSC board/2 (DSCB/2; SC-508) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/2 if faulty. 2 Correct the harness connection of DSIPB if faulty. 3 Replace DSCB/2. 4 Replace DSIPB. 5 Replace MFPB. |
| Error code: | C6912, C6913 |
| Description: | DSC Bus check NG2 • When DSC bus check (back side) detects an error. |
| Causes: | DSC board (SC-507) MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSC board if faulty. - - 2 Change DSC board - - 3 Change MFPB |
| Error code: | C6F01 |
| Description: | Scanner sequence trouble 1. The original transport interval becomes shorter than the predetermined value due to an original transport control error in original reading in DF. |
| Causes: | • MFP board (MFPB) • DF control board (DFCB) |
| Remedy: | 1. Correct the harness connection between main body and DF if faulty. 2. Replace DFCB. 3. Replace MFPB. |
| Error code: | C8101 |
| Description: | Before reading pressure welding alienation mechanism trouble. • During a pressure motion being performed, the before read sensor (PS6) output does not change from H to L. • During a retraction motion being performed, the before read sensor (PS6) output does not change from L to H. |
| Causes: | • Reading roller pressure/retraction motor (M6) • Before read sensor (PS6) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M6-relay CN118-DFCB CN4 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-relay CN120-DFCB CN11 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: DFCB CN11-2 (ON) • Location of electrical component: DF 1-C 5. M6 operation check • Control signal: DFCB CN4-1 to 2 • Location of electrical component: DF 10-C 6. Replace M6. 7. DFCB ICP9 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8102 |
| Description: | Turn around pressure welding alienation trouble •During a pressure motion being performed, the reverse roller sensor (PS7) output does not change from H to L. •During a retraction motion being performed, the reverse roller sensor (PS7) output does not change from L to H. |
| Causes: | Switchback roller pressure/retraction motor (M5) Reverse roller sensor (PS7) DF control board (DFCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M5 for proper drive coupling, and correct as necessary. - - 3 PS7 I/O check, sensor check REYB PJ3-3 (ON) DF-618 K to L-10 4 DFCB F9 conduction check - - 5 M5 operation check DFCB PJ6-10 to 11 DF-618 I-7 6 Change M5 - - 7 DFCB PS2 conduction check - - 8 Change DFCB |
| Error code: | C8103 |
| Description: | Lift up mechanism trouble (Upward movement). The lift up upper sensor (PS2) is not turned ON (unblocked) after a lapse of a given time after the lift-up motor (M5) moves up (is turned forward). |
| Causes: | • Lift-up motor (M5) • Lift up upper sensor (PS2) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M5-DFCB CN9 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-DFCB CN6 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: DFCB CN6-3 (ON) • Location of electrical component: DF 7-I 5. M5 operation check • Control signal: DFCB CN9-1 to 5 • Location of electrical component: DF 5-C 6. Replace M5. 7. DFCB ICP5 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8104 |
| Description: | Glass movement trouble • The glass home sensor (PS203) output does not change from H to L after a lapse of a given time while the original glass moving motor (M202) is working. • The glass home sensor (PS203) output does not change from L to H after a lapse of a given time while the original glass moving motor (M202) is working. |
| Causes: | Original glass moving unit Original glass moving motor (M202) Original glass position control board (OGPCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M202 for proper drive coupling, and correct as necessary. - - 3 Change original glass moving unit - - 4 Change OGPCB |
| Error code: | C8106 |
| Description: | Lift up mechanism failure (Downward movement). The lift up lower sensor (PS3) is not turned ON (unblocked) after a lapse of a given time after the lift-up motor (M5) goes down (is turned backward). |
| Causes: | • Lift-up motor (M5) • Lift up lower sensor (PS3) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M5-DFCB CN9 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS3-DFCB CN10 for proper connection and correct as necessary. 4. PS3 I/O check, sensor check • Control signal: DFCB CN10-3 (ON) • Location of electrical component: DF 10-C 5. M5 operation check • Control signal: DFCB CN9-1 to 5 • Location of electrical component: DF 5-C 6. Replace M5. 7. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8107 |
| Description: | Glass cleaning mechanism trouble. The front side cleaning home sensor (PS18) is not turned ON (unblocked) even after the set period of time has elapsed after the front side cleaning motor (M8) turned ON. |
| Causes: | • Front side cleaning motor (M8) • Front side cleaning home sensor (PS18) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M8-DFCB CN14 for proper connection and correct as necessary. 2. Check the connector between PS18-DFCB CN18 for proper connection and correct as necessary. 3. Check the connector of M8 for proper drive coupling and correct as necessary. 4. PS18 I/O check, sensor check • Control signal: DFCB CN18-3 (ON) • Location of electrical component: DF 3-C 5. M8 operation check • Control signal: DFCB CN14-1 to 4 • Location of electrical component: DF 6-C 6. Replace M8. 7. DFCB ICP8 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8302 |
| Description: | Cooling fan motor`s failure. The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Cooling fan motor (FM) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between FM-relay CN115-DFCB CN19 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM operation check • Control signal: DFCB CN19-3 (LOCK) • Location of electrical component: DF 4-C 4. Replace FM. 5. DFCB ICP10 conduction check. 6. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8401 |
| Description: | Nonvolatile memory error. The EEPROM writing is disabled. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Check the DFCB connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Replace DFCB. |
| Error code: | C9401 |
| Description: | Exposure LED lighting failure The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | C9402 |
| Description: | Exposure LED lighting abnormally The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | C9403 |
| Description: | CIS LED lighting failure <When DF-701 is installed> At the CIS gain adjustment, the machine detected that the output of the CIS LED is lower than the specified value. |
| Causes: | • CIS module (CIS) • DF power supply (DFPU) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection between CIS and DSIPB if faulty. 2 Correct the harness connection between CIS and CISPU if faulty. 3 Replace CIS. 4 CISPU F1, F2 conduction check. 5 Replace CISPU. 6 Replace DSIPB. 7 Replace MFPB. |
| Error code: | C9404 |
| Description: | CIS LED lighting abnormally <When DF-701 is installed> After a scan job is completed, the machine detected that the average output of the CIS LED is greater than the specified value. |
| Causes: | • CIS module (CIS) • DF power supply (DFPU) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection between CIS and DSIPB if faulty. 2 Correct the harness connection between CIS and CISPU if faulty. 3 Replace CIS. 4 CISPU F1, F2 conduction check. 5 Replace CISPU. 6 Replace DSIPB. 7 Replace MFPB. |
| Error code: | CA051 |
| Description: | Standard controller configuration failure • The controller of the printer control board (PRCB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA052 |
| Description: | Controller hardware error • A controller hardware error is detected in the network I/F. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA053 |
| Description: | Controller start failure • A controller start failure is detected in the controller interface. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CB001...CB119 |
| Description: | FAX Board Error |
| Error code: | CC001 |
| Description: | Vendor connection failure |
| Causes: | • Printer control board (PRCB) • Coin vendor (Japan) • Coin vendor kit (North America, Europe) |
| Error code: | CC151 |
| Description: | ROM contents error upon startup (MSC) • A fault is detected in a sequence of ROM contents check of the MSC (PRCB) during starting |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. |
| Error code: | CC152 |
| Description: | ROM contents error upon startup (scanner). A fault is detected in a sequence of ROM contents check of the MFPB during starting |
| Remedy: | 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace the appropriate board. |
| Error code: | CC153 |
| Description: | ROM contents error upon startup (PRT) • A fault is detected in a sequence of ROM contents check of the mechanical control board (MFPB) during starting. |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. |
| Error code: | CC155 |
| Description: | Finisher ROM error |
| Causes: | FS control board (FSCB) |
| Error code: | CC156 |
| Description: | DF ROM error. Data of flash ROM of the DF is determined to be faulty when the main power switch is turned ON. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace DFCB. |
| Error code: | CC157 |
| Description: | Finisher ROM error (ZU). Data of flash ROM of the z-folding unit is determined to be faulty when the power is turned ON. |
| Causes: | ZU control board (ZUCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace ZUCB |
| Error code: | CC158 |
| Description: | Finisher ROM error (RU). When a communication error is detected between the main body and the horizontal transport unit. |
| Causes: | • RU control board (RUCB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace RUCB - - 4 Replace FSCB |
| Error code: | CC159, CC15A |
| Description: | • CC159: ROM contents error upon startup (DSC1) • CC15A: ROM contents error upon startup (DSC2). A fault is detected in a sequence of ROM contents check of the DSC board during starting. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • DSC board/2 (DSCB/2; SC-508) |
| Remedy: | 1. Check DSCB/1 or DSCB/2 connector for proper connection and correct as necessary. 2. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 3. Rewrite the firmware. 4. Replace DSCB/1 or DSCB/2. |
| Error code: | CC15B |
| Description: | Flash ROM error (saddle). <When FS-536SD or FS-537SD is installed> Data of flash ROM of the saddle is determined to be faulty when the main power switch is turned ON. |
| Causes: | SD control board (SDCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace SDCB. (FS-536SD/FS-537SD) |
| Error code: | CC163 |
| Description: | ROM contents error (PRT) • The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Rewrite the firmware. 2 Change PRCB 2.1. Turn OFF the power switch and replace the current PRCB with a new one. (When using a PRCB of another machine in service, be sure to use a PRCB installed in the same model.) 2.2. Update the PRCB firmware. 2.3. After completing the firmware update, turn OFF and ON the power switch and check to see that warm-up is started. 2.4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SV ERB. 3 Change SV ERB 3.1. Replace the current SV ERB with a new one. 3.2. Turn ON the power switch and check to see that warm-up is started. (One minute is spent to prepare the new SV ERB for use. During the period, the control panel backlight stays off.) 3.3. Make the specified readjustments. 4 If the above actions do not solve the problem, contact KMBT. |
| Error code: | CC164 |
| Description: | ROM contents error (MSC) • The wrong model of firmware is detected in the MFP board when the power switch is turned ON. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the corresponding board. 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CC165 |
| Description: | ROM contents error (DF). When the power is turned ON, DF control board or firmware error is detected. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace DFCB |
| Error code: | CC170...CC186 |
| Description: | Dynamic link error during starting (AP0) Dynamic link error during starting (AP1) Dynamic link error during starting (AP2) Dynamic link error during starting (AP3) Dynamic link error during starting (AP4) Dynamic link error during starting (LDR) Dynamic link error during starting (IBR) Dynamic link error during starting (IID) Dynamic link error during starting (IPF) Dynamic link error during starting (IMY) Dynamic link error during starting (SPF) Dynamic link error during starting (OAP). A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 If the malfunction code "C-C172" has occurred, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if "Controller 2," "Controller 3," or "Others" is set for [Image Controller Setting]. If any of these is set, according to the kind of controller, select "Controller 0" or "Controller 1." - - 2 If the malfunction code "C-C180" has occurred, check to install the appropriate loadable driver for an authentication unit which is installed to the MFP. - - 3 Replace MFPB - - 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CC190 |
| Description: | Outline font load error. An error occurred while loading the outline font. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Format the hard disk. 4. Replace the hard disk. (HDD (A) / HDD (B)) 5. Replace MFPB. |
| Error code: | CC191 |
| Description: | Setting parameter load error (LDR). Upon startup, the processing of the loadable device driver setting data file failed. • RAM disk file creation failed. • Reading from the flash ROM failed. • An error occurred in API of the authentication module. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON. 2. Reinstall the loadable device driver. 3. Rewrite the firmware. 4. Replace MFPB. |
| Error code: | CD002 |
| Description: | JOB RAM save error • The error in save of JOB data to the memory/ hard disk and its read error are detected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB. |
| Error code: | CD004, CD00F, CD020 |
| Description: | • CD004: Hard disk access error (connection failure) • CD00F: Hard disk data transfer error • CD020: Hard disk verify error • CD004: Unable to communicate between the hard disk and MFP board (MFPB). • CD00F: Data transfer from the hard disk is faulty. • CD020: The data abnormality is detected by the hard disk verify check. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Reinstall the hard disk. 4. Replace the hard disk. (HDD (A) / HDD (B)) 5. Replace MFPB. |
| Error code: | CD010 |
| Description: | Hard disk unformat. Unformatted hard disk is connected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Carry out the [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format]. 2. Replace the hard disk. (HDD (A) / HDD (B)) 3. Replace MFPB. |
| Error code: | CD011 |
| Description: | Hard disk out of specifications mounted. A hard disk that falls outside the specifications is connected. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD041...CD046 |
| Description: | HDD command execution error. The error occurred inside the hard disk. |
| Causes: | Hard disk |
| Remedy: | 1 Check the hard disk specifications. - - 2 Format the hard disk. 3 Replace the hard disk. |
| Error code: | CD047...CD04B |
| Description: | HDD SCSI library error. The error occurred inside the hard disk. |
| Causes: | Hard disk |
| Remedy: | 1 Check the hard disk specifications. - - 2 Format the hard disk. - - 3 Replace the hard disk. |
| Error code: | CD201...CD203 |
| Description: | File memory mounting error. Memory capacity discrepancy. Memory capacity discrepancy 2 |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if MEMB/1 or MEMB/2 on MFPB is installed correctly. - - 2 Replace MEMB/1 or MEMB/2 on MFPB. - - 3 Replace MFPB. |
| Error code: | CD211, CD212 |
| Description: | • CD211: PCI-SDRAM DMA operation failure • CD212: Compression/extraction timeout detection • CD211: Hardware related to the transfer of memory image of the MFP board (MFPB) fails to respond. • CD212: Hardware related to the BTC compression function of the MFP board (MFPB) fails to respond. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Replace MFPB. |
| Error code: | CD231 |
| Description: | No Fax memory at FAX board mounting |
| Causes: | MFP board (MFPB) FAX board |
| Remedy: | 1 Check to see if the FAX board is installed correctly. - - 2 Change PRCB. |
| Error code: | CD241, CD242 |
| Description: | • CD241: Encryption ASIC setting error • CD242: Encryption ASIC mounting error • CD241: Initialization error of the encrypted ASIC is detected during the machine is starting. • CD242: The faulty of the installation of encrypted ASIC is detected during the machine is starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check the MFP board connector for proper connection and correct as necessary. 2. Replace MFPB |
| Error code: | CD252 |
| Description: | No relay circuit boards for IC-414 mounting at IC-414 mount setting. EFI relay board (EFIRYB; VI-506) are not mounted when the IC-414 is set to mount setting at Service Mode. |
| Causes: | • MFP board (MFPB) • EFI relay board (EFIRYB; VI-506) |
| Remedy: | 1 If the IC-414 is not mounted, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if "Controller 0" is set for [Image Controller Setting]. - - 2 Check the EFI relay board (EFIRYB; VI-506) connector for proper connection and correct as necessary. - - 3 Replace the EFI relay board (EFIRYB; VI-506) - - 4 Replace MFPB |
| Error code: | CD261 |
| Description: | USB hub board failure. • When a failure is detected in USB hub board included in the local interface kit. • Non-standard USB device is connected. |
| Causes: | • MFP board (MFPB) • USB hub board (USBHB: EK-610/EK-611) |
| Remedy: | 1. Check the operation with another USB device. 2. Check the USB hub board connector for proper connection and correct as necessary. 3. Replace the USB hub board. 4. Replace MFPB. |
| Error code: | CD271 |
| Description: | The memory cannot be recognized with the i-Option activated. While the i-Option is activated, the memory on an MFPB cannot be recognized. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CD272 |
| Description: | i-Option activated and HDD not installed. While the i-Option is activated, the hard disk is not installed. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) |
| Remedy: | 1. Access [Service Mode] -> [System 2] -> [HDD] and check to see if “Installed” is selected. 2. Replace the hard disk (A). 3. Replace MFPB. |
| Error code: | CD3## |
| Description: | NVRAM data error |
| Remedy: | . When the data stored due to the NVRAM trouble is lost, backup data can be used for restoration. . Trouble code [C-D370] will be displayed when multiple errors (over 5) of NVRAM data are detected, which can be restored with one restoration command. . Data backup will be automatically performed every hour. Backup can also be performed manually with the following setting. [Service Mode] - [Enhanced Security] - [NVRAM Data Back Up] 1. When a trouble caused by NVRAM data error occurs, the screen below appears. 2. Select [Yes] and touch [OK]. 3. The screen will be shifted to the data restoration screen to perform data restoration. NOTE • When the restoration is performed in a short time, data restoration screen may not be displayed. 4. Check the message which indicates that the data restoration was successfully conducted. Turn OFF the main power switch and turn it ON again more than 10 seconds after. NOTE • In case it failed to restore data, return to the trouble code screen. |
| Error code: | CD401...CD407 |
| Description: | CD401: NACK command incorrect CD402: ACK command incorrect CD403: Checksum error CD404: Receiving packet incorrect CD405: Receiving packet analysis error CD406: ACK receiving timeout CD407: Retransmission timeout |
| Causes: | MFP board (PRCB) |
| Remedy: | 1 Check whether there is an strong electromagnetic noise source near the main body. - - 2 Check the connectors on MFPB for proper connection and correct as necessary. - - 3 Change MFPB. |
| Error code: | CE001...CE007 |
| Description: | CE001: Abnormal message queue CE003: Task error CE004: Event error CE005: Memory access error CE006: Header access error CE007: DIMM initialize error |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Check the connectors on PRCB for proper connection and correct as necessary. - - 2 Change PRCB. |
| Error code: | CE002 |
| Description: | Message and method parameter failure. MFP board (MFPB) is faulty. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF the main power switch and turn it ON again, and conduct the following setting. [Service Mode] -> [System 1] -> [Initialization] - > [Clear All Data]. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) 4. Replace MFPB. |
| Error code: | CEEE1 |
| Description: | MFP board malfunction |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the connectors on MFPB for proper connection and correct as necessary. - - 2 Replace MFPB |
| Error code: | CEEE2 |
| Description: | Scanner section malfunction. A scanner part is faulty. |
| Causes: | • LED exposure unit • CCD board (CCDB) • Scanner drive board (SCDB) |
| Remedy: | 1. Check the connectors on CCDB or MFPB for proper connection and correct as necessary. 2. Replace SCDB 3. Replace the CCD unit. |
| Error code: | CEEE3 |
| Description: | Printer control board (PRCB) |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Check the PRCB connector for proper connection and correct as necessary. - - 2 Replace PRCB |
| Error code: | CF001...CFF15 |
| Description: | MFP Control Board error |
| Error code: | CFB00...CFFA0 |
| Description: | Abort code |
| Causes: | MFP board (MFPB) DIMM0/DIMM1 JPEG board (SA-502) EIF board (IC-412) DS board (bizhub C652DS/C552DS only) |
| Remedy: | 1 Check the MFPB connector for proper connection and correct as necessary. . . 2 Conduct the following setting. [Service Mode] - [Memory/HDD Adj.] - [Memory Check] - [Detail Check]. When gNGh is displayed, replace the appropriate memory or PWB. WORK0: DIMM0 WORK1: DIMM1 FILE0,1: MFP board FILE2,3: EIF board FILE4,5: DS board . . 3 Conduct the following setting. [Service Mode] - [Memory/HDD Adj.] - [JPEG Check]. When gNGh is displayed, replace the JPEG board (JPEGB; SA-502). . . 4 Change MFPB |
Парткод
Название
Konica Minolta Емкость отработанного тонера
Konica Minolta WX-102 Емкость отработанного тонера
Konica Minolta Ролик переноса изображения
Konica Minolta Блок термозакрепления 220v
Konica Minolta DV612K Блок девелопера черный
Konica Minolta IU612Y Блок фотобарабана желтый
Konica Minolta IU612M Блок фотобарабана пурпурный
Konica Minolta IU612C Блок фотобарабана голубой
Konica Minolta DR612K Блок фотобарабана черный
Konica Minolta TN613K Тонер-картридж черный
Konica Minolta TN618 Тонер-картридж черный
Konica Minolta TN613Y Тонер-картридж желтый
Konica Minolta TN613M Тонер-картридж пурпурный
Konica Minolta TN613C Тонер-картридж голубой
Konica Minolta Блок переноса изображения
Konica Minolta Блок ленты переноса
