Konica-Minolta Magicolor 2550

Рейтинг

Коды ошибок
Расходные материалы

Коды ошибок

Описание

Парткод

Название

Konica Minolta Комплект цветных тонер-картриджей

Konica Minolta Тонер-картридж желтый 1500 стр.

Konica Minolta Тонер-картридж желтый 4500 стр.

Konica Minolta Тонер-картридж пурпурный 1500 стр.

Konica Minolta Тонер-картридж пурпурный 4500 стр.

Konica Minolta Тонер-картридж голубой 1500 стр.

Konica Minolta Тонер-картридж голубой 4500 стр.

Konica Minolta Тонер-картридж черный 4500 стр.

Konica Minolta Печка в сборе 220v

Error code:	04
Display:	ERROR CONDITION PAPER OUT
Description:	The printer stops; the ERROR light flashes.
Causes:	The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded.
Remedy:	Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration.

Error code:	05
Display:	ERROR CONDITION HEAD OPEN
Description:	The printer stops; the ERROR light flashes.
Causes:	The printhead is not fully closed. The head open sensor is not working properly.
Remedy:	Replace the sensor.

Error code:	08
Display:	WARNING HEAD COLD
Description:	The printer prints while the ERROR light flashes.
Causes:	The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor.
Remedy:	Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead.

Error code:	0B
Description:	Transfer Fan Malfunction
Causes:	Ventilation Fan Motor (M6) PWB-A (Engine Control Board) Power Unit (PU)
Remedy:	1 Check the M6 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 Check the PWB-A connector for proper connection and correct as necessary. 4 M6 operation check. PWB-A PJ10A-1 (REM) PWB-A PJ10A-3 (LOCK) 2-H 5 Change PWB-A. 6 Change PU.

Error code:	0C
Description:	Power Supply Cooling Fan Malfunction
Causes:	Power Supply Cooling Fan Motor (M4) PWB-A (Engine Control Board) Power Unit (PU)
Remedy:	1 Check the M4 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 Check the PWB-A connector for proper connection and correct as necessary. 4 M4 operation check. PWB-A PJ4A-1 (REM) PWB-A PJ4A-3 (LOCK) 7-I 5 Change PWB-A. 6 Change PU.

Error code:	0F
Display:	Paper Jam
Description:	Sorter full or empty
Causes:	1 Harness connection failure of back cover sensor. 2 Back cover damaged. 3 Back cover sensor failure. 4 Main PCB failure.

Error code:	10
Display:	DEFRAGMENTING
Description:	The printer stops.
Causes:	The printer is defragmenting memory.
Remedy:	Caution • Do NOT turn off the printer power during defragmenting. Doing so can damage the printer. Allow the printer to finish defragmenting. If you get this error message frequently, check your label formats. Formats that write to and erase memory frequently may cause the printer to defragment often. Using properly coded label formats usually minimizes the need for defragmenting. If this error message does not go away, contact Technical Support. The printer requires service.

Error code:	12
Description:	General print quality issues
Causes:	The printer is set at the incorrect print speed. You are using an incorrect combination of labels and ribbon for your application. The printer is set at an incorrect darkness level. The printhead is dirty. Incorrect or uneven printhead pressure. The printhead is improperly balanced.
Remedy:	For optimal print quality, set the print speed to the lowest possible setting for your application via control panel, the driver, or the software. See Adjust Print Speed on page 79. You may want to perform the FEED Self Test on page 120. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. For optimal print quality, set the darkness to the lowest possible setting for your application via the control panel, the driver, or the software. See Adjust Print Darkness on page 78. You may want to perform the FEED Self Test on page 120 to determine the ideal darkness setting. Clean the printhead. See Clean the Printhead and Platen Roller on page 131. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Adjust the printhead balance.

Error code:	14
Description:	Wrinkled ribbon
Causes:	Ribbon fed through the machine incorrectly. Incorrect burn temperature. Incorrect or uneven printhead pressure. Media not feeding properly; walking from side to side. The strip plate needs adjusting. The printhead needs vertical adjustment. The printhead is improperly balanced. The printhead and platen roller need to be realigned.
Remedy:	See Load Ribbon on page 64. Set the darkness to the lowest possible setting for good print quality. See Adjust Print Darkness on page 78. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Make sure that media is snug by adjusting the media guide, or call a service technician. Adjust the printhead balance.

Error code:	15
Description:	Printing too light or too dark over the entire label
Causes:	The media or ribbon is not designed for high-speed operation. You are using an incorrect combination of media and ribbon for your application. You are using ribbon with direct thermal media. Incorrect or uneven printhead pressure.
Remedy:	Replace supplies with those recommended for high-speed operation. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. Direct thermal media does not require ribbon. To check if you are using direct thermal media, perform the label scratch test in When to Use Ribbon on page 62. Set the pressure to the minimum needed. See Adjust Printhead Pressure on page 70.

Error code:	16
Description:	Smudge marks on labels
Causes:	The media or ribbon is not designed for high-speed operation.
Remedy:	Replace supplies with those recommended for high-speed operation.

Error code:	17
Description:	Misregistration/skips labels
Causes:	The printer is not calibrated. Improper label format.
Remedy:	Recalibrate the printer. Use correct label format.

Error code:	18
Description:	Misregistration and misprint of one to three labels
Causes:	The platen roller is dirty. Media does not meet specifications.
Remedy:	See Clean the Printhead and Platen Roller on page 131. Use media that meets specifications.

Error code:	19
Description:	Vertical drift in top-of-form position
Causes:	The printer is out of calibration. Vertical drift occurs during normal printer operation. Note • A vertical drift of ± 4 to 6 dot rows (approximately 0.5 mm) is within normal tolerances. The platen roller is dirty.
Remedy:	Recalibrate the printer. Calibrate the printer. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131.

Error code:	1A
Description:	Disconnect
Causes:	Transmission has not started (the phone line is too noisy).
Remedy:	Check the quality of the phone line or restart the transmission at a later time.

Error code:	1B
Description:	Document transmission fault
Causes:	Document transmission error.
Remedy:	Transmission: restart the transmission. Reception: ask your correspondent to retransmit the document.

Error code:	21
Description:	The bar code printed on a label does not scan.
Causes:	The bar code is not within specifications because the print is too light or too dark. Not enough blank space around the bar code.
Remedy:	Perform the FEED Self Test on page 120. Adjust the darkness or print speed settings as necessary. Leave at least 1/8 in. (3.2 mm) between the bar code and other printed areas on the label and between the bar code and the edge of the label.

Error code:	24
Description:	A label format was sent to the printer but was not recognized. The DATA light does not flash.
Causes:	The communication parameters are incorrect.
Remedy:	Check the printer driver or software communications settings (if applicable). If you are using serial communication, check the serial port setting in the control panel menu. See Set Serial Communications on page 91. If you are using serial communication, make sure you are using a null modem cable or a null modem adapter. Using the control panel controls, check the protocol setting. It should be set to NONE. See Set Protocol on page 93. If a driver is used, check the driver communication settings for your connection.

Error code:	29
Description:	The ribbon light is on even though ribbon is loaded correctly.
Causes:	The printer was not calibrated for the label and ribbon being used.
Remedy:	Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90.

Error code:	2A
Display:	No Ink Cartridge
Description:	Faulty NVRAM Data
Causes:	NVRAM PWB-A (Engine Control Board)
Remedy:	1 Unplug the power cord and plug it in, then turn OFF and ON the Power Switch. 2 Check NVRAM (PJ26) on PWB-A for proper connection and correct as necessary. 3 Change PWB-A.

Konica-Minolta Magicolor 2550

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку