Konica-Minolta Magicolor 7450 II
Рейтинг
Модули
WASTE TONER BOX SECTION
ERASER SECTION
PAPER TRANSPORT SECTION
DEVELOPMENT DRIVE SECTION
WASTE TONER TRANSPORT SECTION
MANUAL FEED SECTION 3
FUSING SECTION
PAPER EXIT DRIVE SECTION
MPT CASSETTE TRAY SECTION
MAIN FRAME
MANUAL FEED SECTION 2
P/H FRAME SECTION
PAPER EXIT SECTION
TRANSPORT DRIVE SECTION
MPT CASSETTE PAPER TAKE-UP SECTION
POWER UNIT
INNER COVER SECTION
MPT PAPER TAKE-UP SECTION
CONTACT SECTION
P/H FRAME SECTION 2
REAR DUCT SECTION
RIGHT DOOR SECTION
Fusing Drive Section
EXTERNAL PARTS
T/C RAIL SECTION
MANUAL FEED SECTION
TRANSFER BELT SECTION
Детали WASTE TONER TRANSPORT SECTION
| Деталь: | TONER PIPE |
| Парткод: | 4038 R732 00 |
| Деталь: | LABEL |
| Парткод: | 4038 7311 02 |
| Деталь: | RAIL |
| Парткод: | 4038 2013 04 |
| Деталь: | Waste Toner Box |
| Парткод: | 4065 621 |
| Деталь: | Waste Toner Box |
| Парткод: | 4065 622 |
| Деталь: | SHIELD PLATE |
| Парткод: | 4038 2199 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2182 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2181 01 |
| Деталь: | LED PILOT LAMP |
| Парткод: | 9353 2400 11 |
| Деталь: | BRACKET |
| Парткод: | 4038 2015 02 |
| Деталь: | RAIL |
| Парткод: | 4038 2014 08 |
| Деталь: | LABEL K |
| Парткод: | 4039 7350 01 |
| Деталь: | LABEL C |
| Парткод: | 4039 7349 01 |
| Деталь: | LABEL M |
| Парткод: | 4039 7348 01 |
| Деталь: | LABEL Y |
| Парткод: | 4039 7347 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2040 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2056 02 |
| Деталь: | DUCT |
| Парткод: | 4038 2052 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2053 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2081 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2151 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2104 02 |
| Деталь: | SHUTTER |
| Парткод: | 4038 2103 04 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2105 03 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2032 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2183 01 |
| Деталь: | ERASER YMC ASSY |
| Парткод: | 4038 R744 00 |
| Деталь: | ERASER K ASSY |
| Парткод: | 4038 R704 00 |
| Деталь: | PIPE K ASSY |
| Парткод: | 4038 R709 00 |
| Деталь: | PIPE YMC ASSY |
| Парткод: | 4038 R710 00 |
| Деталь: | POLYESTER FILM |
| Парткод: | 4038 1273 00 |
| Деталь: | SEAL |
| Парткод: | 9J06 1015 01 |
| Деталь: | SEAL |
| Парткод: | 9J06 1016 00 |
| Деталь: | SEAL |
| Парткод: | 9J06 1017 00 |
| Деталь: | POLYESTER FILM |
| Парткод: | 9J06 1018 00 |
| Деталь: | Label M1 |
| Парткод: | 4038 7303 01 |
| Деталь: | HANDLE |
| Парткод: | 4038 3532 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3529 02 |
| Деталь: | GUIDE |
| Парткод: | 4038 3539 01 |
| Деталь: | ROLLER |
| Парткод: | 4038 3501 01 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 21 |
| Деталь: | GUIDE |
| Парткод: | 4038 3537 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3538 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3536 01 |
| Деталь: | ROLLER |
| Парткод: | 4038 3502 02 |
| Деталь: | GUIDE |
| Парткод: | 4038 3540 03 |
| Деталь: | GUIDE |
| Парткод: | 4038 7022 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 7023 00 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 3530 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 3525 01 |
| Деталь: | BUSHING |
| Парткод: | 4025 3572 01 |
| Деталь: | GEAR 20T |
| Парткод: | 4004 3503 02 |
| Деталь: | GEAR 14T |
| Парткод: | 4004 3504 02 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3567 01 |
| Деталь: | FIXED POWER RESISTORS |
| Парткод: | V800 5003 00 |
| Деталь: | SEAL |
| Парткод: | 4128 3522 02 |
| Деталь: | ACTUATOR |
| Парткод: | 4038 3562 01 |
| Деталь: | PRISM |
| Парткод: | 9335 1400 11 |
| Деталь: | WASHER |
| Парткод: | 4038 3593 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3592 01 |
| Деталь: | PHOTO SENSING ELEMENT |
| Парткод: | V869 9000 45 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 3531 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6830 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 3561 03 |
| Деталь: | HUMIDITY CONVERTION EL. |
| Парткод: | 9372 5400 31 |
| Деталь: | TORSION SPRING |
| Парткод: | 1164 3527 02 |
| Деталь: | CLUTCH |
| Парткод: | 9322 1300 21 |
| Деталь: | SEAL |
| Парткод: | 4038 3556 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 3559 01 |
| Деталь: | COVER |
| Парткод: | 4038 3558 02 |
| Деталь: | GUIDE |
| Парткод: | 4038 3527 03 |
| Деталь: | TRANSPORT UNIT |
| Парткод: | 4038 R759 00 |
| Деталь: | SPACER |
| Парткод: | 4038 5603 00 |
| Деталь: | SEAL |
| Парткод: | 4038 7010 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2074 05 |
| Деталь: | BRACKET |
| Парткод: | 4039 2076 03 |
| Деталь: | CAP |
| Парткод: | A02E 1196 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2075 02 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2073 02 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3517 03 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6836 01 |
| Деталь: | MOTOR |
| Парткод: | 4038 M101 00 |
| Деталь: | MOTOR |
| Парткод: | 4038 M102 00 |
| Деталь: | HOPPER DRIVE ASSY |
| Парткод: | 4038 R729 00 |
| Деталь: | DEVELOP DRIVE ASSY |
| Парткод: | 4038 R730 00 |
| Деталь: | BRACKET |
| Парткод: | 4039 1011 01 |
| Деталь: | DUCT |
| Парткод: | 4039 1152 02 |
| Деталь: | FAN MOTOR |
| Парткод: | 4040 M100 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2118 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2076 01 |
| Деталь: | PIPE |
| Парткод: | 4038 2116 04 |
| Деталь: | STIRRING PLATE |
| Парткод: | 4038 2131 07 |
| Деталь: | SEAL |
| Парткод: | 4038 2117 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2119 01 |
| Деталь: | LID |
| Парткод: | 4038 2115 02 |
| Деталь: | BUSHING |
| Парткод: | 4004 5607 02 |
| Деталь: | GEAR 18/30T |
| Парткод: | 4004 2545 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2579 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2586 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4004 5612 01 |
| Деталь: | PIPE |
| Парткод: | 4038 2111 02 |
| Деталь: | SCREW |
| Парткод: | 4038 2112 04 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2114 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2143 01 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2142 01 |
| Деталь: | BUSHING |
| Парткод: | 4038 2120 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | BRACKETASSY |
| Парткод: | 4038 0203 02 |
| Деталь: | STOP PLATE |
| Парткод: | 4038 2089 01 |
| Деталь: | GEAR 32/30T |
| Парткод: | 4038 2140 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4038 2130 01 |
| Деталь: | SHUTTER |
| Парткод: | 4038 2113 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2062 01 |
| Деталь: | SEAL |
| Парткод: | 4038 1272 00 |
| Деталь: | PIPE ASSY |
| Парткод: | 4038 R745 00 |
| Деталь: | CLUTCH ASSY |
| Парткод: | 4038 3260 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 3240 01 |
| Деталь: | BUSHING |
| Парткод: | 4030 3093 01 |
| Деталь: | GEAR 30T |
| Парткод: | 4038 3246 01 |
| Деталь: | GEAR 30T |
| Парткод: | 4038 3247 01 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | CAM |
| Парткод: | 4038 3236 01 |
| Деталь: | ROLLER |
| Парткод: | 4131 3001 01 |
| Деталь: | STOP RING |
| Парткод: | 4142 3217 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 3232 01 |
| Деталь: | GEAR 25T |
| Парткод: | 1075 2565 01 |
| Деталь: | CLUTCH |
| Парткод: | 9J06 M201 00 |
| Деталь: | SOLENOID |
| Парткод: | 9J06 M200 00 |
| Деталь: | BRACKET |
| Парткод: | 4038 3244 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 3249 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | BUSHING |
| Парткод: | 4004 5339 01 |
| Деталь: | SHIELD PLATE |
| Парткод: | 4038 3237 01 |
| Деталь: | FUSING UNIT 110-127V |
| Парткод: | 4039 R739 11 |
| Деталь: | FUSING UNIT 220-240V |
| Парткод: | 4039 R740 11 |
| Деталь: | Fusing Unit 100V |
| Парткод: | 4039 R738 11 |
| Деталь: | HOLDER |
| Парткод: | 4038 2082 04 |
| Деталь: | BRACKET |
| Парткод: | 4038 3735 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6822 02 |
| Деталь: | ACTUATOR |
| Парткод: | 4038 5728 03 |
| Деталь: | GUIDE |
| Парткод: | 4039 5853 02 |
| Деталь: | TORSION SPRING |
| Парткод: | 4039 5858 01 |
| Деталь: | COLLAR |
| Парткод: | 4139 5577 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4039 5859 02 |
| Деталь: | PLATE SPRING |
| Парткод: | 4039 5882 01 |
| Деталь: | BUSHING |
| Парткод: | 4038 5860 01 |
| Деталь: | ROLLER |
| Парткод: | 4038 5901 01 |
| Деталь: | ROLL |
| Парткод: | 4038 5915 01 |
| Деталь: | SHAFT |
| Парткод: | 4025 5984 01 |
| Деталь: | BRACKET |
| Парткод: | 4039 5855 01 |
| Деталь: | DUCT |
| Парткод: | 4038 5869 01 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 5874 01 |
| Деталь: | GEAR 23/21T |
| Парткод: | 4038 5870 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4038 5873 01 |
| Деталь: | GEAR 33/32T |
| Парткод: | 4038 5879 01 |
| Деталь: | GEAR 24/20T |
| Парткод: | 4038 5877 02 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 5862 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 5864 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 5872 02 |
| Деталь: | GEAR 17/16T |
| Парткод: | 4038 5871 02 |
| Деталь: | GEAR 16T |
| Парткод: | 4039 5878 01 |
| Деталь: | PAPER EXIT DRIVE ASSY |
| Парткод: | 4039 R702 00 |
| Деталь: | PIN |
| Парткод: | 4036 2549 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | 4036 3022 03 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4687 3281 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4134 3106 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4036 3008 01 |
| Деталь: | LABEL MP CD |
| Парткод: | 4039 9453 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 5601 00 |
| Деталь: | LEVER |
| Парткод: | 4037 3210 01 |
| Деталь: | GUIDE |
| Парткод: | 4004 3040 02 |
| Деталь: | GUIDE |
| Парткод: | 4004 3024 01 |
| Деталь: | LEVER |
| Парткод: | 1164 3061 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1164 3062 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4004 3033 01 |
| Деталь: | GUIDE |
| Парткод: | 4004 3038 01 |
| Деталь: | SEAL |
| Парткод: | 4004 3008 01 |
| Деталь: | Label Paper supply |
| Парткод: | 4038 7337 01 |
| Деталь: | CASSETTE |
| Парткод: | 4036 3021 02 |
| Деталь: | COVER |
| Парткод: | 4039 5637 00 |
| Деталь: | LABEL |
| Парткод: | 4039 9486 00 |
| Деталь: | HANDLE |
| Парткод: | 4039 5641 00 |
| Деталь: | COVER |
| Парткод: | 4039 5645 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LEVER |
| Парткод: | 4004 3051 02 |
| Деталь: | BRACKET |
| Парткод: | 4004 3031 01 |
| Деталь: | SPACER |
| Парткод: | 4037 3226 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4037 3223 01 |
| Деталь: | RACK |
| Парткод: | 4004 3032 01 |
| Деталь: | GUIDE |
| Парткод: | 4021 3036 01 |
| Деталь: | GUIDE |
| Парткод: | 4004 3042 01 |
| Деталь: | GEAR 20T |
| Парткод: | 1164 3045 01 |
| Деталь: | Label FD |
| Парткод: | 4039 9452 00 |
| Деталь: | RAIL |
| Парткод: | 4039 5604 00 |
| Деталь: | SPACER |
| Парткод: | 4037 3227 01 |
| Деталь: | LABEL CAPACITY |
| Парткод: | 4004 7324 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4036 3028 12 |
| Деталь: | BRAKE |
| Парткод: | 4036 3086 01 |
| Деталь: | LEVER |
| Парткод: | 4036 3019 01 |
| Деталь: | LABEL NEAR EMPTY |
| Парткод: | 4039 9487 00 |
| Деталь: | REGULATING PLATE R ASSY |
| Парткод: | 4038 R712 00 |
| Деталь: | MULTIPURPOSE CASSETT |
| Парткод: | 4039 R766 00 |
| Деталь: | SPACER |
| Парткод: | 4038 3595 01 |
| Деталь: | BRACKET |
| Парткод: | 4039 1047 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4039 2286 01 |
| Деталь: | SWITCH |
| Парткод: | 4038 M601 00 |
| Деталь: | BRACKET |
| Парткод: | 4038 2065 17 |
| Деталь: | COVER |
| Парткод: | 4128 2215 01 |
| Деталь: | COVER |
| Парткод: | 4038 2066 12 |
| Деталь: | CAP |
| Парткод: | A02E 1196 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2073 02 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6810 05 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996 3055 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2097 02 |
| Деталь: | PROTECTION |
| Парткод: | 1154 4670 01 |
| Деталь: | SEAL |
| Парткод: | 4039 2209 01 |
| Деталь: | SEAL |
| Парткод: | 4039 2210 01 |
| Деталь: | COVER |
| Парткод: | A0EP 5912 00 |
| Деталь: | BRACKET |
| Парткод: | 4038 3207 03 |
| Деталь: | FRAME |
| Парткод: | 4038 3208 02 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 3217 01 |
| Деталь: | LEVER |
| Парткод: | 4038 3216 03 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 3220 01 |
| Деталь: | LEVER |
| Парткод: | 4038 3218 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 5656 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 5658 00 |
| Деталь: | GUIDE |
| Парткод: | 4030 3403 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4038 5653 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 3268 02 |
| Деталь: | GUIDE |
| Парткод: | A0EP 5901 00 |
| Деталь: | FIXED POWER RESISTORS |
| Парткод: | V800 5003 00 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 3266 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 3261 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 3262 03 |
| Деталь: | GUIDE |
| Парткод: | 4038 3270 01 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 5662 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3475 01 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | 4034 0151 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3267 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3269 02 |
| Деталь: | COLLAR |
| Парткод: | 4038 5651 00 |
| Деталь: | FRAME ASSY |
| Парткод: | 4038 0251 14 |
| Деталь: | EDGE COVER |
| Парткод: | 4038 5665 00 |
| Деталь: | GUIDE |
| Парткод: | A0EP 5941 01 |
| Деталь: | SPACER |
| Парткод: | 4037 7001 00 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4038 R736 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 5657 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 5664 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 5663 00 |
| Деталь: | SPACER |
| Парткод: | 4038 5672 00 |
| Деталь: | SEAL |
| Парткод: | 4038 5605 00 |
| Деталь: | COLLAR |
| Парткод: | 4039 2289 01 |
| Деталь: | PWB ASSY |
| Парткод: | 4039 H011 00 |
| Деталь: | ROLL |
| Парткод: | 4038 2094 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | 4038 2016 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2017 01 |
| Деталь: | PORYESTER FILM |
| Парткод: | 4038 1281 00 |
| Деталь: | CONNECTOR ASSY |
| Парткод: | 4038 R737 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2249 02 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6840 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2067 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2051 01 |
| Деталь: | COLLAR |
| Парткод: | 4038 2086 01 |
| Деталь: | PU LIFT REAR ASSY |
| Парткод: | 4038 R705 00 |
| Деталь: | PU LIFT FRONT ASSY |
| Парткод: | 4038 R702 00 |
| Деталь: | COVER |
| Парткод: | 4039 8912 00 |
| Деталь: | LABEL |
| Парткод: | 4039 9488 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | 4039 5919 01 |
| Деталь: | GUIDE |
| Парткод: | 4039 5854 04 |
| Деталь: | EARTH GROUND |
| Парткод: | 4039 5857 01 |
| Деталь: | GUIDE |
| Парткод: | 4039 5908 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4039 5903 04 |
| Деталь: | ACTUATOR |
| Парткод: | 4039 5904 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | HOLDER |
| Парткод: | 4039 5902 03 |
| Деталь: | NETURALIZING MEMBER |
| Парткод: | 4039 5907 02 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6835 01 |
| Деталь: | PLUG HOUSING |
| Парткод: | V818 6000 15 |
| Деталь: | COVER |
| Парткод: | 4039 8911 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J06 M100 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | 4039 5909 01 |
| Деталь: | Neutralizing Brush |
| Парткод: | 4039 5920 01 |
| Деталь: | Gear 83/115T |
| Парткод: | 4038 2513 01 |
| Деталь: | Gear 65T |
| Парткод: | 4038 2520 01 |
| Деталь: | GEAR 26T |
| Парткод: | 4038 2529 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4038 2599 01 |
| Деталь: | GEAR 32/18T |
| Парткод: | 4038 2531 01 |
| Деталь: | GEAR 24T |
| Парткод: | 4038 2532 01 |
| Деталь: | CLUTCH |
| Парткод: | 9322 1300 31 |
| Деталь: | GEAR 49/44T |
| Парткод: | 4038 2551 01 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 02 |
| Деталь: | GEAR 22T |
| Парткод: | 4038 2519 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2598 01 |
| Деталь: | PIN |
| Парткод: | 4038 2699 01 |
| Деталь: | Gear 50T |
| Парткод: | 4038 2514 01 |
| Деталь: | GEAR 37/50T |
| Парткод: | 4038 2549 01 |
| Деталь: | CLUTCH |
| Парткод: | 9322 1400 21 |
| Деталь: | GEAR 22/38T |
| Парткод: | 4038 2517 01 |
| Деталь: | GEAR 55/31T |
| Парткод: | 4038 2508 01 |
| Деталь: | GEAR 20/56T |
| Парткод: | 4038 2578 01 |
| Деталь: | GEAR 18/30T |
| Парткод: | 4004 2545 01 |
| Деталь: | SHIELD |
| Парткод: | 4038 2253 01 |
| Деталь: | TRANSPORT DRIVE ASSY |
| Парткод: | 4038 R701 00 |
| Деталь: | SEAL |
| Парткод: | 4038 2450 00 |
| Деталь: | WEIGHT |
| Парткод: | 4038 3063 01 |
| Деталь: | WASHER |
| Парткод: | 4036 3030 01 |
| Деталь: | WASHER |
| Парткод: | 4036 3031 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3020 01 |
| Деталь: | WASHER |
| Парткод: | 1164 3066 01 |
| Деталь: | SHAFT |
| Парткод: | 4004 3001 02 |
| Деталь: | ROLLER |
| Парткод: | 4034 3012 01 |
| Деталь: | COLLAR |
| Парткод: | 4004 3005 01 |
| Деталь: | STOP RING |
| Парткод: | 4658 3046 01 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | 4034 0151 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 5654 00 |
| Деталь: | SHAFT |
| Парткод: | 4658 3040 01 |
| Деталь: | COLLAR |
| Парткод: | 4038 5655 00 |
| Деталь: | BRACKET |
| Парткод: | 4004 3004 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4004 3006 03 |
| Деталь: | BUSHING |
| Парткод: | 1164 3003 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4036 3040 01 |
| Деталь: | SPACER |
| Парткод: | 4039 5602 00 |
| Деталь: | EARTH GROUND |
| Парткод: | 4036 3018 01 |
| Деталь: | PIN |
| Парткод: | 4036 3014 01 |
| Деталь: | PAWL |
| Парткод: | 1164 3004 03 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1164 3005 02 |
| Деталь: | STOPPER |
| Парткод: | 4039 5601 00 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4038 R748 00 |
| Деталь: | FRAME |
| Парткод: | 4039 2005 06 |
| Деталь: | SEAL |
| Парткод: | 4038 2178 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6832 02 |
| Деталь: | SUPPORT |
| Парткод: | V502 0100 26 |
| Деталь: | BRACKET |
| Парткод: | 4038 2071 02 |
| Деталь: | BRACKET |
| Парткод: | 4039 2242 02 |
| Деталь: | BRACKET |
| Парткод: | 4039 2246 01 |
| Деталь: | LABEL EARTH |
| Парткод: | 1500 2320 02 |
| Деталь: | POWER SUPPLY |
| Парткод: | 4039 6201 03 |
| Деталь: | POWER SUPPLY |
| Парткод: | 4039 6202 03 |
| Деталь: | FUN MOTOR |
| Парткод: | 4039 M100 00 |
| Деталь: | COLLAR |
| Парткод: | 4038 2309 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6827 04 |
| Деталь: | SHIELD |
| Парткод: | 4039 2244 02 |
| Деталь: | PWB ASSY |
| Парткод: | 4039 H001 01 |
| Деталь: | PWB ASSY (PS/PCL) |
| Парткод: | 4039 H004 00 |
| Деталь: | BRACKET |
| Парткод: | 4039 2213 01 |
| Деталь: | SHIELD |
| Парткод: | 4039 2214 03 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6845 07 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6838 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6839 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6804 03 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4039 2245 01 |
| Деталь: | SHIELD |
| Парткод: | 4039 2243 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9384 1500 11 |
| Деталь: | COLLAR |
| Парткод: | 4039 2289 01 |
| Деталь: | PWB-M |
| Парткод: | 4039 H010 00 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326 1410 31 |
| Деталь: | PWB-R |
| Парткод: | 4039 0106 02 |
| Деталь: | BRACKET |
| Парткод: | 4039 2215 03 |
| Деталь: | PROTECTION |
| Парткод: | 1154 4670 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6834 01 |
| Деталь: | PWB ASSY |
| Парткод: | A011 M711 00 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326 1000 91 |
| Деталь: | BRACKET |
| Парткод: | 4038 2265 04 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06 M601 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2283 02 |
| Деталь: | HOLDER |
| Парткод: | 4038 2281 04 |
| Деталь: | CONNECTOR PIN |
| Парткод: | V816 3000 02 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6815 02 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2282 03 |
| Деталь: | COVER |
| Парткод: | 4038 1101 06 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038 1014 01 |
| Деталь: | COVER |
| Парткод: | 4038 1102 02 |
| Деталь: | LABEL TC IU |
| Парткод: | 4038 7308 02 |
| Деталь: | LABEL K |
| Парткод: | 4039 7350 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 1105 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6816 01 |
| Деталь: | PLATE |
| Парткод: | 4039 1104 03 |
| Деталь: | LABEL Y |
| Парткод: | 4039 7347 01 |
| Деталь: | LABEL M |
| Парткод: | 4039 7348 01 |
| Деталь: | LABEL C |
| Парткод: | 4039 7349 01 |
| Деталь: | BAND |
| Парткод: | 4643 1020 03 |
| Деталь: | SET PLATE |
| Парткод: | 1053 3103 01 |
| Деталь: | POWER SOURCE SWITCH |
| Парткод: | A02E M601 00 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6812 02 |
| Деталь: | FRONT COVER SW ASSY |
| Парткод: | 4038 R770 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 2287 02 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2266 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 1360 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3541 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2099 01 |
| Деталь: | RAIL |
| Парткод: | 4039 5603 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 1164 3053 12 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6829 02 |
| Деталь: | HOLDER |
| Парткод: | 4004 3062 06 |
| Деталь: | PHOTO INTERUPPTER |
| Парткод: | 9J06 R901 00 |
| Деталь: | ACTUATOR |
| Парткод: | 1164 3027 01 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335 1400 61 |
| Деталь: | ACTUATOR |
| Парткод: | 4004 3061 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4004 3063 01 |
| Деталь: | CUSHION |
| Парткод: | 4038 2162 02 |
| Деталь: | RAIL |
| Парткод: | 4039 1121 00 |
| Деталь: | HOLDER |
| Парткод: | 1164 3022 02 |
| Деталь: | PWB ASSY |
| Парткод: | 4037 0104 01 |
| Деталь: | LEVER |
| Парткод: | 1164 3020 03 |
| Деталь: | SPACER |
| Парткод: | 4004 3052 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 1164 3054 01 |
| Деталь: | BRACKET |
| Парткод: | 4004 3011 01 |
| Деталь: | LEVER |
| Парткод: | 4004 3012 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3054 01 |
| Деталь: | SEAL |
| Парткод: | 4039 1606 00 |
| Деталь: | COVER |
| Парткод: | 4039 1644 00 |
| Деталь: | SIZE DETECTING PWB ASSY |
| Парткод: | 4038 R740 00 |
| Деталь: | BRACKET |
| Парткод: | 4038 5666 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 5667 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 7021 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2275 01 |
| Деталь: | IU CONTACT PLATE ASSY |
| Парткод: | 4038 0760 00 |
| Деталь: | CONTACT ASSY |
| Парткод: | 4038 R707 00 |
| Деталь: | COVER |
| Парткод: | 4038 2255 01 |
| Деталь: | REAR COVER |
| Парткод: | 4039 1639 00 |
| Деталь: | HOLDER |
| Парткод: | 4039 1127 00 |
| Деталь: | COVER |
| Парткод: | 4039 1642 00 |
| Деталь: | REAR COVER |
| Парткод: | 4039 1638 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2206 02 |
| Деталь: | HOLDER |
| Парткод: | 4038 2274 03 |
| Деталь: | CONTACT |
| Парткод: | 4038 2225 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2276 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2277 01 |
| Деталь: | COVER |
| Парткод: | 4038 2232 13 |
| Деталь: | HV TRANSFORMER |
| Парткод: | 4038 6203 03 |
| Деталь: | CONTACT B ASSY |
| Парткод: | 4038 R708 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 1906 04 |
| Деталь: | GEAR 27T |
| Парткод: | 4038 2189 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 2187 04 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 2044 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2194 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2193 03 |
| Деталь: | BRACKET |
| Парткод: | 4038 1280 00 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2196 01 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2191 02 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2190 03 |
| Деталь: | SHAFT |
| Парткод: | 4038 2192 02 |
| Деталь: | BRACKETASSY |
| Парткод: | 4038 0211 04 |
| Деталь: | GEAR 30T |
| Парткод: | 4038 2188 02 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 2184 01 |
| Деталь: | WASHER |
| Парткод: | 4038 2179 01 |
| Деталь: | SPRING |
| Парткод: | 4038 2042 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2043 03 |
| Деталь: | CONTACT |
| Парткод: | 4038 2180 01 |
| Деталь: | SKEW ADJUSTMENT ASSY |
| Парткод: | 4038 R731 00 |
| Деталь: | PRINT HEAD UNIT |
| Парткод: | 4039 R723 00 |
| Деталь: | FUN MOTOR |
| Парткод: | 4039 M100 00 |
| Деталь: | DUCT |
| Парткод: | 4038 2031 01 |
| Деталь: | DUCT |
| Парткод: | 4038 2033 01 |
| Деталь: | DUCT |
| Парткод: | 4038 2034 04 |
| Деталь: | DUCT |
| Парткод: | 4038 2055 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2241 02 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6808 02 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6818 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2237 01 |
| Деталь: | LEFT COVER |
| Парткод: | 4039 1640 00 |
| Деталь: | BRACKET |
| Парткод: | 4037 2239 02 |
| Деталь: | SEAL |
| Парткод: | 4004 2148 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | COLLAR |
| Парткод: | 4038 2309 01 |
| Деталь: | RAIL |
| Парткод: | 4039 2196 04 |
| Деталь: | DUCT |
| Парткод: | 4039 1151 00 |
| Деталь: | SEAL |
| Парткод: | 4039 1153 00 |
| Деталь: | POWER CORD |
| Парткод: | 4037 0775 01 |
| Деталь: | COVER |
| Парткод: | 4039 7013 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3520 01 |
| Деталь: | CAM |
| Парткод: | 4038 3553 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 4611 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 3542 02 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LEVER |
| Парткод: | 4038 3551 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 3516 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 4620 01 |
| Деталь: | Label JAM |
| Парткод: | 4038 7302 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 3571 02 |
| Деталь: | LEVER |
| Парткод: | 4038 3552 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3512 02 |
| Деталь: | COLLAR |
| Парткод: | 4038 3534 01 |
| Деталь: | BRACKETASSY |
| Парткод: | 4038 0210 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 3511 02 |
| Деталь: | STOPPER |
| Парткод: | 4038 3523 01 |
| Деталь: | COVER DUP |
| Парткод: | A02F 1637 01 |
| Деталь: | DOOR ASSY |
| Парткод: | 4039 R765 00 |
| Деталь: | ROLLER ASSY |
| Парткод: | 4038 R742 00 |
| Деталь: | MOTOR |
| Парткод: | 9314 1400 71 |
| Деталь: | BRACKET |
| Парткод: | 4038 2556 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2592 01 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2591 01 |
| Деталь: | GEAR 37T |
| Парткод: | 4038 2540 01 |
| Деталь: | GEAR 81/17T |
| Парткод: | 4038 2538 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2557 01 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 02 |
| Деталь: | SHAFT |
| Парткод: | 4038 2573 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2596 01 |
| Деталь: | GEAR 20T |
| Парткод: | 4038 2574 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2576 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 2577 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2588 01 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2580 01 |
| Деталь: | GEAR 22T |
| Парткод: | 4038 2575 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2600 02 |
| Деталь: | SHAFT |
| Парткод: | 4038 2587 01 |
| Деталь: | GEAR 20T |
| Парткод: | 4038 2541 01 |
| Деталь: | CLUTCH |
| Парткод: | 9322 1300 21 |
| Деталь: | GEAR 41T |
| Парткод: | 4038 2593 02 |
| Деталь: | PLUG HOUSING |
| Парткод: | V818 6000 14 |
| Деталь: | BRACKET |
| Парткод: | 4039 1017 01 |
| Деталь: | Fusing Drive Assy |
| Парткод: | 4038 R793 00 |
| Деталь: | TOP COVER |
| Парткод: | 4039 1631 00 |
| Деталь: | COVER |
| Парткод: | 4039 1641 00 |
| Деталь: | TOP COVER |
| Парткод: | 4039 1635 00 |
| Деталь: | RIGHT COVER |
| Парткод: | 4039 1636 00 |
| Деталь: | HINGE |
| Парткод: | 4038 1010 01 |
| Деталь: | SHAFT |
| Парткод: | 1136 1019 03 |
| Деталь: | CLEANING PAD |
| Парткод: | 4038 2084 06 |
| Деталь: | SET PLATE |
| Парткод: | 1053 3103 01 |
| Деталь: | BAND |
| Парткод: | 4643 1020 03 |
| Деталь: | SEAL |
| Парткод: | 4025 1018 01 |
| Деталь: | SCREW |
| Парткод: | V126 0308 03 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475 2603 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 1046 01 |
| Деталь: | FRONT COVER |
| Парткод: | 4039 1632 01 |
| Деталь: | LABEL |
| Парткод: | 4039 9480 00 |
| Деталь: | Logo Mark |
| Парткод: | A00J 9455 00 |
| Деталь: | CLANING MATERIAL |
| Парткод: | 4038 2083 02 |
| Деталь: | LABEL REMOVE |
| Парткод: | 4039 7301 03 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | 4039 M704 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | 4039 M705 00 |
| Деталь: | LEFT COVER |
| Парткод: | 4039 1634 00 |
| Деталь: | LEFT COVER |
| Парткод: | 4039 1643 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4039 1045 01 |
| Деталь: | SHIELD |
| Парткод: | 4039 2247 01 |
| Деталь: | REAR COVER |
| Парткод: | 4039 1633 00 |
| Деталь: | RIGHT COVER |
| Парткод: | 4039 1637 00 |
| Деталь: | ELECTRICALLY CONDUCTIVE MATERIAL |
| Парткод: | 4039 6751 01 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326 1210 81 |
| Деталь: | COVER ASSY |
| Парткод: | 4039 R768 00 |
| Деталь: | Label Inch |
| Парткод: | 4039 9483 00 |
| Деталь: | Label Metric |
| Парткод: | 4039 9484 00 |
| Деталь: | LABEL REORDER |
| Парткод: | 4039 7342 01 |
| Деталь: | LABEL REORDER |
| Парткод: | 4039 7343 01 |
| Деталь: | LABEL REORDER |
| Парткод: | 4039 7344 01 |
| Деталь: | LABEL REORDER |
| Парткод: | 4039 7345 01 |
| Деталь: | LABEL REORDER |
| Парткод: | 4039 7346 01 |
| Деталь: | POWER CORD |
| Парткод: | 9381 4200 21 |
| Деталь: | POWER CORD |
| Парткод: | 9381 4300 31 |
| Деталь: | POWER CORD |
| Парткод: | 4139 N300 00 |
| Деталь: | POWER CORD |
| Парткод: | 9381 4101 31 |
| Деталь: | CLAMP |
| Парткод: | V500 0200 40 |
| Деталь: | Label Emperon |
| Парткод: | A011 9462 00 |
| Деталь: | RAIL |
| Парткод: | 4038 2019 01 |
| Деталь: | SET PLATE |
| Парткод: | 4038 2038 02 |
| Деталь: | PAWL |
| Парткод: | 4039 2161 03 |
| Деталь: | PAWL |
| Парткод: | 4039 2162 03 |
| Деталь: | PAWL |
| Парткод: | 4039 2163 03 |
| Деталь: | PAWL |
| Парткод: | 4039 2164 03 |
| Деталь: | PAWL |
| Парткод: | 4039 2165 03 |
| Деталь: | LABEL K |
| Парткод: | 4039 7358 01 |
| Деталь: | LABEL C |
| Парткод: | 4039 7357 01 |
| Деталь: | LABEL M |
| Парткод: | 4039 7356 01 |
| Деталь: | LABEL Y |
| Парткод: | 4039 7355 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4039 6814 01 |
| Деталь: | RAIL |
| Парткод: | 4039 2020 01 |
| Деталь: | RAIL |
| Парткод: | 4039 2021 01 |
| Деталь: | RAIL |
| Парткод: | 4038 2022 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2102 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2109 01 |
| Деталь: | STIRRING MEMBER |
| Парткод: | 4038 2108 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2150 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2110 03 |
| Деталь: | SEAL |
| Парткод: | 4039 2208 01 |
| Деталь: | GUIDE ASSY |
| Парткод: | 4038 R706 00 |
| Деталь: | LEVER |
| Парткод: | 4038 1271 00 |
| Деталь: | SEAL |
| Парткод: | 9J06 1013 00 |
| Деталь: | SEAL |
| Парткод: | 4038 1311 00 |
| Деталь: | TRAY ASSY |
| Парткод: | 4038 0165 00 |
| Деталь: | HOLDER |
| Парткод: | 4039 5685 00 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6834 03 |
| Деталь: | GUIDE |
| Парткод: | 4038 3229 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3234 02 |
| Деталь: | ACTUATOR |
| Парткод: | 4038 3233 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | TRAY |
| Парткод: | 4039 5680 00 |
| Деталь: | LABEL |
| Парткод: | 4039 9485 00 |
| Деталь: | COVER |
| Парткод: | A0EP 5906 00 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 3215 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4039 3282 01 |
| Деталь: | HOLD PLATE |
| Парткод: | 4038 3253 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 3252 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3256 01 |
| Деталь: | COVER |
| Парткод: | 4039 5684 00 |
| Деталь: | BRACKET ASSY |
| Парткод: | 4038 0252 03 |
| Деталь: | GEAR 13/18T |
| Парткод: | 4030 3412 01 |
| Деталь: | RACK |
| Парткод: | 4030 3460 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 3272 01 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6845 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | 4038 3251 02 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4687 3281 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4038 3222 03 |
| Деталь: | BRAKE |
| Парткод: | 4038 3286 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | 4038 3221 03 |
| Деталь: | POLYESTER FILM |
| Парткод: | 4038 5671 00 |
| Деталь: | SCALE INCH |
| Парткод: | 4038 7352 01 |
| Деталь: | SCALE METRIC |
| Парткод: | 4039 9451 00 |
| Деталь: | BRAKE |
| Парткод: | 4038 3255 01 |
| Деталь: | Manual Feed Tray Unit |
| Парткод: | 4039 R764 00 |
| Деталь: | RAIL |
| Парткод: | 4038 2023 18 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2029 01 |
| Деталь: | LEVER |
| Парткод: | 4038 2046 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2048 01 |
| Деталь: | ARM |
| Парткод: | 4038 2047 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2080 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2045 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2077 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2152 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2153 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2078 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2205 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2207 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2151 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2217 01 |
| Деталь: | RAIL |
| Парткод: | 4038 2024 02 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6836 01 |
| Деталь: | ARM |
| Парткод: | 4038 2027 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2028 01 |
| Деталь: | LEVER |
| Парткод: | 4038 2026 01 |
| Деталь: | TRANSFER KIT |
| Парткод: | 4039 R716 00 |
| Деталь: | SWITCH ASSY |
| Парткод: | 4038 R733 00 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4038 6835 01 |
Коды ошибок
0001
0018
0019
001A
001B
0040
0043
0046
0048
004C
004E
004F
0094
0096
0301
0302
0303
0304
0311
0312
0313
0314
0500
0501
0510
0511
0520
0521
0900
0910
0950
0960
0F30
0F31
0F32
0F33
0F34
0F35
0F36
0F37
0F3A
0F3B
0F3C
0F3D
13B0
13C8
13CA
13D0
13D1
13D2
13D3
13D4
13D9
13DA
13DB
13DC
13E2
3000
C002
C003
C013
C015
C022
C025
C026
C027
C050
C051
C052
C053
C054
C060
C061
C062
C063
C064
C065
FFFF
Описание
| Error code: | 0001 |
| Display: | Main motor failure CODE (001) Turn power off, on |
| Description: | Main Motor Failure The Main Motor lock signal remains HIGH for a predetermined consecutive period of time while the Main Motor remains energized. |
| Causes: | • Main Motor, PL9.1.6 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check the Engine Control Board connector P/J8. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the Main Motor for proper positioning. Is the motor engaged with the gears? Go to step 3. Reseat the motor drive properly. If the problem persists, go to step 3. 3 Check the operation of the Main Motor. Is the motor faulty? Replace the motor. If the problem persists, go to step 4. Go to step 4. 4 On the Engine Control Board, check P/J2 at pins 1, 5, and 7 for +24V. Are the voltages present? Go to step 5. Go to step 6. 5 Replace the Engine Control Board. Does the problem persist? Go to step 5. Complete. 6 Replace the Power Supply. Complete. |
| Error code: | 0018 |
| Display: | D MOTOR 2 |
| Description: | Color PC Drum Motor’s failure to turn • The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning. |
| Causes: | • Developing motor (M1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector of motor for proper connection and correct as necessary. 2 Check the connector of motor for proper drive coupling and correct as necessary. 3 Check the PWB-M connector for proper connection and correct as necessary. 4 M2 operation check PWB-M CNDM3-5 (REM) PWB-M CNDM3-8 (LOCK) C-23. 5 Change PWB-M. |
| Error code: | 0019 |
| Description: | Color PC Drum Motor’s turning at abnormal timing • The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary |
| Remedy: | 1 M2 operation check PWB-M CNDM3-5 (REM) PWB-M CNDM3-8 (LOCK) C-23. 2 Change PWB-M. |
| Error code: | 001A |
| Description: | Color Developing Motor’s failure to turn • The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning. |
| Remedy: | 1 Check the connector of motor for proper connection and correct as necessary. 2 Check the connector of motor for proper drive coupling and correct as necessary. 3 Check the PU1 connector for proper connection and correct as necessary. 4 Check the PWB-M connector for proper connection and correct as necessary. 5 M3 operation check PWB-M CNDM2-5 (REM) PWB-M CNDM2-8 (LOCK) C-22. 6 Change PU1. 7 Change PWB-M. |
| Error code: | 001B |
| Display: | Toner rack failure CODE (001B) Turn power off, on |
| Description: | Toner Rack Failure |
| Causes: | • Rack Positioning Sensor, PL5.1.12 • Engine Control Board, PL13.0.20 |
| Remedy: | 1 Check the Rack Motor connector P/J5 on the Engine Control Board. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the Engine Control Board connector P/J5. Is the connector seated properly? Go to step 3. Reseat the connector. If the problem persists, go to step 3. 3 Check the Rack Positioning Sensor at PJ5-11. Is the sensor on? Go to step 4. Replace the sensor. If the problem persists, go to step 4. 4 Replace the Engine Control Board. Complete. |
| Error code: | 0040 |
| Description: | SCAN MOTOR ERROR |
| Causes: | Scan Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.) |
| Remedy: | < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. ) |
| Error code: | 0043 |
| Description: | Cooling Fan Motor/1’s failure to turn • The Fan Lock signal remains HIGH for a predetermined continuous period of time while the Motor remains stationary. |
| Remedy: | 1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M12 operation check PWB-M CNDM2-15 (ON) PWB-M CNDM2-16 (LOCK) C-22. 4 Change PWB-M7. |
| Error code: | 0046 |
| Display: | FUSER FAN |
| Description: | Fusing Cooling Fan Motor/1’s failure to turn • The Fan Lock signal remains HIGH for a predetermined continuous period of time while the Motor remains stationary. |
| Causes: | Fusing cooling fan motor (FM1) Print control board (PRCB) |
| Remedy: | 1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M11 operation check PWB-M CNDM1-12 (ON) PWB-M CNDM1-14 (LOCK) K to L-1 to 2. 4 Change PWB-M. |
| Error code: | 0048 |
| Description: | Fusing Cooling Fan Motor/2’s failure to turn • The Fan Lock signal remains HIGH for a predetermined continuous period of time while the Motor remains stationary |
| Remedy: | 1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M13 operation check PWB-M CNDM1-14 (ON) PWB-M CNDM1-17 (LOCK) K to L-1. 4 Change PWB-M. |
| Error code: | 004C |
| Display: | Exhaust fan failure CODE (004C) Turn power off, on |
| Description: | Exhaust Fan Failure The Ventilation Fan Motor does not rotate evenly even after the lapse of a given period of time while it is starting. |
| Causes: | • Ventilation Fan Motor, PL7.2.20 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check the Engine Control Board connector P/J16. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the operation of the Ventilation Fan Motor. Is the motor faulty? Replace the motor. If the problem persists, go to step 5. Go to step 5. 3 On the Engine Control Board, check for +24 VDC at P/J2-1, 5, and 7. Check for +5 VDC at P/J2-2. Are the voltages present and within specification? Go to step 4. Replace the Power Supply. If the problem persists, go to step 4. 4 Replace the Engine Control Board. Complete. |
| Error code: | 004E |
| Display: | LVPS fan failure CODE (004E) Turn power off, on |
| Description: | LVPS Fan Failure • The Power Supply Cooling Fan Motor does not rotate evenly even after the lapse of a given period of time while it is being started. • The motor lock signal remains HIGH for a given period of consecutive time while the Power Supply Cooling Fan Motor is being rotated. |
| Causes: | • Power Supply Cooling Fan Motor, PL12.0.11 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check the High Voltage Board connectors CN1 and CN2, and the Engine Control Board connector P/J17. Are the connectors seated properly? Go to step 2. Reseat the connector(s). If the problem persists, go to step 2. 2 Check the Power Supply Cooling Fan Motor control signals at CN2. Are the signals operating correctly? Replace the motor. If the problem persists, go to step 3. Go to step 3. 3 Check the Power Supply Cooling Fan Motor control signals at PJ17 on the Engine Control Board. Are the control signals operating correctly? Replace the High Voltage Board. If the problem persists, go to step 4. Go to step 4. 4 On the Engine Control Board, check for +24 VDC at P/J2-1, 5, and 7. Check for +5 VDC at P/J2-2. Are the voltages present and within specification? Go to step 5. Replace the Power Supply. If the problem persists, go to step 5. 5 Replace the Engine Control Board. Complete. |
| Error code: | 004F |
| Description: | Cooling Fan Motor 2’s failure to turn • The Fan Lock signal remains HIGH for a predetermined continuous period of time while the Motor remains stationary. |
| Remedy: | 1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M22 operation check PWB-M CNR2FAN-4 (ON) PWB-M CNR2FAN-6 (LOCK) L-22. 4 Change PWB-M. |
| Error code: | 0094 |
| Display: | Trans. roll failure CODE (0094) Turn power off, on |
| Description: | Transfer Roll Failure Possible causes: • The 2nd Image Transfer Retraction Position Sensor(PS3) is not activated (retracted position) within a given period of time after the retraction sequence of the 2nd transfer roller has been started. • The 2nd Image Transfer Retraction Position Sensor is not deactivated (pressed position) within a given period of time after the pressure sequence of the 2nd transfer roller has been started. |
| Causes: | • 2nd Image Transfer Retraction Position Sensor (PS3), PL4.0.9 • 2nd Image Transfer Retraction Position Solenoid (SD4), PL7.2.23 • Main Motor, PL9.1.6 • Engine Control Board, PL13.0.20 |
| Remedy: | 1 Check the Main Motor connector CN37. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the Main Motor for proper drive coupling and correct as necessary. Does the problem persist? Go to step 3. Complete. 3 Check the 2nd Image Transfer Retraction Position Solenoid connector CN5. Is the connector seated properly? Go to step 4. Reseat the connector. If the problem persists, go to step 4. 4 Check the 2nd Image Transfer Retraction Position Solenoid for proper drive coupling and correct as necessary. Does the problem persist? Go to step 5. Complete. 5 Check the 2nd Image Transfer Retraction Position Sensor control signal for a voltage change at P/J12-3 on the Engine Control Board. Is the signal operating correctly? Go to step 6. Replace the Engine Control Board. If the problem persists, go to step 6. 6 Replace the 2nd Image Transfer Retraction Position Solenoid. Does the problem persist? Go to step 7. Complete. 7 Replace the 2nd Image Transfer Retraction Position Sensor. Complete. |
| Error code: | 0096 |
| Display: | XFER DETACH 1 |
| Description: | Transfer Belt Separation • The 1st Image Transfer Pressure/Retraction Position Sensor doesn’t turn ON (Retracting) even after the lapse of a given period of time after the 1st Image Transfer Pressure/Retraction Clutch has turned ON during the Transfer Belt is retracting. • The 1st Image Transfer Pressure/Retraction Position Sensor doesn’t turn OFF (Pressuring) even after the lapse of a given period of time after the 1st Image Transfer Pressure/Retraction Clutch has turned ON during the Transfer Belt is pressuring. |
| Causes: | • 1st transfer pressure sensor (PS17) • Transport motor (M2) • 1st transfer pressure solenoid (SD1) • Printer control board (PRCB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 PC6 I/O check, Sensor check 3 CL3 operation check PWB-M CNDM1-11 (ON) K to L-2. 4 M1 operation check PWB-M CNDM1-5 (REM) PWB-M CNDM1-8 (LOCK) K to L-2. 5 Change PWB-M. |
| Error code: | 0301 |
| Description: | SDRAM DIMM (option) read/verify failed. |
| Causes: | Replace the SDRAM DIMM if this error is frequent. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH Unit. 3 Change PWB-D. 4 Change PWB-M7. |
| Error code: | 0302 |
| Description: | NVRAM R/W An error was detected in reading or writing NVRAM. |
| Remedy: | 1. Remove the right side cover. See “Right side cover removal”. 2. Remove the left side cover. See “Left side cover removal”. 3. Remove the rear cover. See “Rear cover removal”. 4. Remove the front door/operator panel/camera assembly. See “Front door/operator panel/camera assembly removal”. 5. Disconnect all cables from the system board. 6. Remove the four screws (A) from the system board shield, and the one screw (B) from the system board. 7. Lift the system board, and remove. 8. Remove the media sensor. |
| Error code: | 0303 |
| Description: | Memory Failure Unable to initialize memory. |
| Remedy: | Replace the system board. |
| Error code: | 0304 |
| Description: | Hardware Failure General hardware failure (unable to localize failure to a specific system). |
| Remedy: | Replace the system board. |
| Error code: | 0311 |
| Description: | Laser malfunction (Cyan) • SOS signal is not detected even after the lapse of a given period of time after staring the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH Unit. 3 Change PWB-D. 4 Change PWB-M7. |
| Error code: | 0312 |
| Description: | Laser malfunction (Magenta) • SOS signal is not detected even after the lapse of a given period of time after staring the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH Unit. 3 Change PWB-D. 4 Change PWB-M7. |
| Error code: | 0313 |
| Description: | Laser malfunction (Yellow) • SOS signal is not detected even after the lapse of a given period of time after staring the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH Unit. 3 Change PWB-D. 4 Change PWB-M7. |
| Error code: | 0314 |
| Description: | Laser malfunction (Black) • SOS signal is not detected even after the lapse of a given period of time after staring the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH Unit. 3 Change PWB-D. 4 Change PWB-M7. |
| Error code: | 0500 |
| Display: | FUSER ERROR |
| Description: | Fuser warm-up failure |
| Causes: | • The thermistor /1 does not detect the specified temperature and the warm-up cycle is not completed even after the lapse of a given period of time after the cycle has been started. |
| Remedy: | 1 Change fuser unit. - - 2 For C110: 1. Main switch is turned ON. 2. Open the top cover. 3. Press the following keys in this order. ROTATE TONER key -ATTENTION key - ATTENTION key - ROTATE TONER key. 4. Main switch is turned OFF/ON. For C130n: 1. Main switch is turned ON. 2. Execute [SERVICE MENU] - [FUSER UNLOCK]. See P.103 - - 3 Change PRCB. - - 4 Change DCPU. - - |
| Error code: | 0501 |
| Display: | FUSER ERROR |
| Description: | Fusing Pressure Roller warm-up failure • The Fusing Pressure Roller Thermistor/1 (TH2) fails to raise a given degree of temperature even after the lapse of a given period of time after the Fusing Pressure Heater Lamp (H3) is turned ON. • The detected temperature of the Fusing Pressure Roller Thermistor/1 (TH2) is lower for a given level of degree than one of the Heating Roller Thermistor/1 (TH1) after the Front Door is opened or closed, the Main Power Switch is turned ON or TROUBLE RESET is implemented. |
| Causes: | 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-M. 5 Change PU1. |
| Error code: | 0510 |
| Display: | Fuser failure CODE (0510) Turn power off, on |
| Description: | 0502 Thermistor Failure, 0510 Fuser Failure, and 0520 Fuser Failure 0510 Fuser Failure The temperature detected by the thermistor remains lower than expected for a given period of time or longer. |
| Causes: | • Fuser, PL4.0.13 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check that the Fuser is installed correctly. Does the problem persist? Go to step 2. Complete. 2 Check the Engine Control Board connectors P/J2, P/J3, and P/J6. Are the connectors seated properly? Go to step 3 Reseat the connectors. If the problem persists, go to step 3. 3 Check the Low Voltage Power Supply connectors CN3, CN5, and CN7. Are the connectors seated properly? Go to step 4. Reseat the connectors. If the problem persists, go to step 4. 4 Replace the Fuser (8-9). Does the problem persist? Go to step 5. Complete. 5 Replace the Engine Control Board. Does the problem persist? Go to step 6. Complete. 6 Replace the Power Supply. Complete. |
| Error code: | 0511 |
| Display: | FUSER ERROR |
| Description: | Abnormally low Fusing Pressure Roller temperature • The temperature of the Fusing Pressure Roller Thermistor /1 (TH2) is lower than a given level of degree for 1 second or more uninterruptedly during Ready mode, Low Power mode or printing. |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-M. 5 Change PU1. |
| Error code: | 0520 |
| Display: | Fuser failure CODE (0520) Turn power off, on |
| Description: | 0502 Thermistor Failure, 0510 Fuser Failure, and 0520 Fuser Failure 0520 Fuser Failure The temperature detected by the thermistor remains higher than expected for a given period of time or longer. |
| Causes: | • Fuser, PL4.0.13 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check that the Fuser is installed correctly. Does the problem persist? Go to step 2. Complete. 2 Check the Engine Control Board connectors P/J2, P/J3, and P/J6. Are the connectors seated properly? Go to step 3 Reseat the connectors. If the problem persists, go to step 3. 3 Check the Low Voltage Power Supply connectors CN3, CN5, and CN7. Are the connectors seated properly? Go to step 4. Reseat the connectors. If the problem persists, go to step 4. 4 Replace the Fuser (8-9). Does the problem persist? Go to step 5. Complete. 5 Replace the Engine Control Board. Does the problem persist? Go to step 6. Complete. 6 Replace the Power Supply. Complete. |
| Error code: | 0521 |
| Display: | FUSER ERROR |
| Description: | Abnormally high Fusing Pressure Roller temperature • The temperature of the Fusing Pressure Roller Thermistor/1 (TH2) is higher than a given level of degree for 1 second or more uninterruptedly before the Heater temperature control starts. • The temperature of the Fusing Pressure Roller Thermistor/1 (TH2) is higher than a given level of degree for 1 second or more uninterruptedly after the Heater temperature control starts. |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-M. 5 Change PU1. |
| Error code: | 0900 |
| Display: | Print Unable 09 Turn the power off and then back on again. |
| Description: | FAX software incompatible detection error Incompatible FAX control PWB is installed. |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | Defective FAX software. Install the fax software. Defective FAX control PWB. Replace the fax control PWB and check for correct operation. |
| Error code: | 0910 |
| Description: | Tray 3 Elevator failure • The Lift-Up Sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started. |
| Remedy: | 1 Check the M3 connector for proper connection and correct as necessary. 2 Check the connector of M3 for proper drive coupling and correct as necessary. 3 PC7 I/O check, Sensor check PWB-Z PJ6Z PC-3 (ON) V-21 to 22. 4 M3 operation check PWB-Z PJ4Z PC-4 to 5 Q-24. 5 Change PWB-Z. |
| Error code: | 0950 |
| Description: | Tray 5 Elevator failure • The Lift-Up Sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started. |
| Remedy: | 1 Check the M3 connector for proper connection and correct as necessary. 2 Check the connector of M3 for proper drive coupling and correct as necessary. 3 PC7 I/O check, Sensor check PWB-Z PJ6Z PC-3 (ON) V-21 to 22. 4 M3 operation check PWB-Z PJ4Z PC-4 to 5 Q-24. 5 Change PWB-Z. |
| Error code: | 0960 |
| Description: | Manual Tray Rise Descent Error • The Bypass Lift-Up Sensor is not blocked even when the Tray 2 Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the standby position to the feed position was started. • The Bypass Lift-Up Sensor is not unblocked even when the Tray 2 Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the feed position to the standby position was started. |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the connector of M2 for proper drive coupling and correct as necessary. 3 PC14 I/O check, Sensor check PWB-M CNTRY1-10 (ON) C-10. 4 M2 operation check PWB-Z PJ5Z PC-5 to 8 Q-22. 5 Change PWB-Z. |
| Error code: | 0F30 |
| Description: | Abnormally low toner density detected Cyan TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 5 % or less for a given number of times consecutively. |
| Remedy: | 1 Perform image troubleshooting procedure if image density is low. 2 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty 3 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23. 4 Reinstall Imaging Unit. 5 Change Imaging Unit. 6 Change PWB-M. 7 Change PWB-P. |
| Error code: | 0F31 |
| Description: | Abnormally high toner density detected Cyan TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 12 % or more for a given number of times consecutively |
| Remedy: | 1 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty. 2 Reinstall Imaging Unit. 3 Change Imaging Unit. 4 Change PWB-M. 5 Change PWB-P. |
| Error code: | 0F32 |
| Description: | Abnormally low toner density detected Magenta TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 5 % or less for a given number of times consecutively. |
| Remedy: | 1 Perform image troubleshooting procedure if image density is low. 2 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty 3 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23. 4 Reinstall Imaging Unit. 5 Change Imaging Unit. 6 Change PWB-M. 7 Change PWB-P. |
| Error code: | 0F33 |
| Description: | Abnormally high toner density detected Magenta TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 12 % or more for a given number of times consecutively. |
| Remedy: | 1 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty. 2 Reinstall Imaging Unit. 3 Change Imaging Unit. 4 Change PWB-M. 5 Change PWB-P. |
| Error code: | 0F34 |
| Description: | Abnormally low toner density detected Yellow TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 5 % or less for a given number of times consecutively. |
| Remedy: | 1 Perform image troubleshooting procedure if image density is low. 2 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty 3 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23. 4 Reinstall Imaging Unit. 5 Change Imaging Unit. 6 Change PWB-M. 7 Change PWB-P. |
| Error code: | 0F35 |
| Description: | Abnormally high toner density detected Yellow TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 12 % or more for a given number of times consecutively. |
| Remedy: | 1 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty. 2 Reinstall Imaging Unit. 3 Change Imaging Unit. 4 Change PWB-M. 5 Change PWB-P. |
| Error code: | 0F36 |
| Description: | Abnormally low toner density detected Black TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Remedy: | 1 Perform image troubleshooting procedure if image density is low. 2 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty. 3 M7 operation check PWB-M CNDM3-10 to 13 C-23. 4 Reinstall Imaging Unit. 5 Change Imaging Unit /K. 6 Change PWB-M. 7 Change PWB-P. |
| Error code: | 0F37 |
| Description: | Abnormally high toner density detected Black TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 12 % or more for a given number of times consecutively. |
| Remedy: | 1 Correct the TCR connection on the underside of the Imaging Unit if faulty. 2 Reinstall Imaging Unit. 3 Change Imaging Unit. 4 Change PWB-M. 5 Change PWB-P. |
| Error code: | 0F3A |
| Description: | Cyan TCR Sensor adjustment failure • TCR Sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Remedy: | 1 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty. 2 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23. 3 Reinstall Imaging Unit. 4 Change Imaging Unit. 5 Change PWB-M. 6 Change PWB-P. |
| Error code: | 0F3B |
| Description: | Magenta TCR Sensor adjustment failure • TCR Sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Remedy: | 1 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty. 2 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23. 3 Reinstall Imaging Unit. 4 Change Imaging Unit. 5 Change PWB-M. 6 Change PWB-P. |
| Error code: | 0F3C |
| Description: | Yellow TCR Sensor adjustment failure • TCR Sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Remedy: | 1 Clean the TCR Sensor window on the underside of the Imaging Unit if dirty. 2 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23. 3 Reinstall Imaging Unit. 4 Change Imaging Unit. 5 Change PWB-M. 6 Change PWB-P. |
| Error code: | 0F3D |
| Description: | Black TCR Sensor adjustment failure • TCR Sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Remedy: | 1 Clean or correct each contact of the Imaging Unit if faulty. 2 M7 operation check PWB-M CNDM3-10 to 13 C-23. 3 Reinstall Imaging Unit /K. 4 Change Imaging Unit /K. 5 Change PWB-M. 6 Change PWB-P. |
| Error code: | 13B0 |
| Description: | RTC failure • When correct access to the RTC Board is failed during access. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PWB-R. 3 Change PWB-M. |
| Error code: | 13C8 |
| Description: | Transfer Unit New Article Release • A new installation is not detected when a new Transfer Cleaner Unit (Image Transfer Belt Unit) is installed. |
| Remedy: | 1 Reinstall Unit. 2 Change PWB-MD. |
| Error code: | 13CA |
| Description: | Fusing Unit New Article Release • A new installation is not detected when a new Fusing Unit is installed. |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M for proper connection and correct or change as necessary. 3 Reinstall Fusing Unit. 4 Change Fusing Unit. 5 Change PWB-M. |
| Error code: | 13D0 |
| Display: | EEPROM1 |
| Description: | Trouble related to Security |
| Error code: | 13D1 |
| Description: | Cyan Imaging Unit EEPROM access error • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. |
| Remedy: | 1 Clean the connection between the Imaging Unit and the machine if dirty. 2 Reinstall Imaging Unit. 3 Change Imaging Unit. 4 Change PWB-M. |
| Error code: | 13D2 |
| Description: | Magenta Imaging Unit EEPROM access error • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. |
| Remedy: | 1 Clean the connection between the Imaging Unit and the machine if dirty. 2 Reinstall Imaging Unit. 3 Change Imaging Unit. 4 Change PWB-M. |
| Error code: | 13D3 |
| Description: | Yellow Imaging Unit EEPROM access error • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. |
| Remedy: | 1 Clean the connection between the Imaging Unit and the machine if dirty. 2 Reinstall Imaging Unit. 3 Change Imaging Unit. 4 Change PWB-M. |
| Error code: | 13D4 |
| Description: | Black Imaging Unit EEPROM access error • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. |
| Remedy: | 1 Clean the connection between the Imaging Unit and the machine if dirty. 2 Reinstall Imaging Unit. 3 Change Imaging Unit. 4 Change PWB-M. |
| Error code: | 13D9 |
| Description: | Cyan Toner Cartridge EEPROM access error • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. |
| Remedy: | 1 Clean the connection between the Toner Cartridge and the machine if dirty. 2 Reinstall Toner Cartridge. 3 Change Toner Cartridge. 4 Change PWB-M. |
| Error code: | 13DA |
| Description: | Magenta Toner Cartridge EEPROM access error • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. |
| Remedy: | 1 Clean the connection between the Toner Cartridge and the machine if dirty. 2 Reinstall Toner Cartridge. 3 Change Toner Cartridge. 4 Change PWB-M. |
| Error code: | 13DB |
| Description: | Yellow Toner Cartridge EEPROM access error • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. |
| Remedy: | 1 Clean the connection between the Toner Cartridge and the machine if dirty. 2 Reinstall Toner Cartridge. 3 Change Toner Cartridge. 4 Change PWB-M. |
| Error code: | 13DC |
| Description: | Black Toner Cartridge EEPROM access error • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. |
| Remedy: | 1 Clean the connection between the Toner Cartridge and the machine if dirty. 2 Reinstall Toner Cartridge. 3 Change Toner Cartridge. 4 Change PWB-M. |
| Error code: | 13E2 |
| Display: | Engine ROM failure CODE (13E2) Turn power off, on |
| Description: | Engine ROM Failure Flash ROM writing is found faulty during a check. |
| Causes: | • Engine Control Board, PL13.0.20 • Image Processor Board, PL2.0.4 |
| Remedy: | 1 Check the Engine Control Board connectors. Are the connectors seated properly? Go to step 2. Reseat the connectors. If the problem persists, go to step 2. 2 Replace the Engine Control Board. Does the problem persist? Go to step 3. Complete. 3 Replace the Image Processor Board. Complete. |
| Error code: | 3000 |
| Description: | Main Motor`s failure to turn • The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning. |
| Causes: | The AC power has been shut off due to a power failure, unplugged, PSH BOARD failure, or MAIN BOARD failure or the like. |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the PWB-M connector for proper connection and correct as necessary. 4 M1 operation check PWB-M CNDM1-5 (REM) PWB-M CNDM1-8 (LOCK) K to L-2. 5 Change PWB-M. 6 Change PU1. |
| Error code: | C002 |
| Display: | RAM ERROR |
| Description: | RAM (standard) error at startup • RAM error at Standard Memory is detected during printer start-up. |
| Causes: | • MFP board (MFPB) • Standard memory |
| Remedy: | 1 Turn OFF the Power Switch of the printer and turn it ON again (Restart of the printer.) 2 Check connection state of the extension memory and correct as necessary. 3 Check the PWB-P connector for proper connection and correct as necessary. 4 Change the extension memory. 5 Change PWB-P. |
| Error code: | C003 |
| Display: | RAM ERROR |
| Description: | Memory copy PCB 2 problem* 1 • Problems with data from memory copy PCB 2. |
| Causes: | Defective memory copy PCB 2. |
| Remedy: | Replace memory copy PCB 2 and check for correct operation. |
| Error code: | C013 |
| Display: | H/W ADDRESS |
| Description: | MAC address error at startup (MAC address is invalid) • Invalid Mac address is detected during printer start-up. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Turn OFF the Power Switch of the printer and turn it ON again (Restart of the printer.) 2 Check the PWB-P connector for proper connection and correct as necessary. 3 Change PWB-P. |
| Error code: | C015 |
| Display: | BOOT ROM |
| Description: | Backup memory read/write problem (engine PCB) • Read and write data does not match. |
| Causes: | Defective backup RAM or engine PCB. |
| Remedy: | Replace the engine PCB and check for correct operation. |
| Error code: | C022 |
| Display: | NVRAM ERROR |
| Description: | Developer unit mixer motor-YMC locking error: The developer unit mixer motor-YMC is not rotating normally |
| Causes: | Developer unit mixer motor-YMC LGC board |
| Remedy: | (1) Pull out the EPU tray and perform the output check (03-115) to check if the 3 outputs of the YMCdeveloper unit mixer are rotating normally. When it is not rotating (2) Is the connector of the YMC-developer unit mixer motor connected securely? (3) Check if the harness or connector of the YMC-drum motor is disconnected or open-circuited. (4) Check if the YMC-developer unit mixer motor is abnormal. (5) Check if the drive gear array has any abnormality such as breakage. When it is rotating (6) Check if developer material is excessively supplied to each YMC-developer unit. (7) Check if the drive gear array of each YMC-developer unit has any abnormality such as breakage. |
| Error code: | C025 |
| Display: | CONTROLLER ROM |
| Description: | Controller ROM error • Lead error of destination setting file is detected during the printer starting. |
| Causes: | MFP board (MFPB) |
| Error code: | C026 |
| Display: | CONTROLLER ROM |
| Description: | Memory PCB communication problem • There is no reply after five retries at transmitting. • There is no reply after five retries at receiving. |
| Causes: | Poor contact in the connector terminals. Defective main PCB or memory PCB. |
| Remedy: | Check the connection of connector CN3 on the main PCB and the connector on memory PCB. Repair or replace if necessary. Replace the main PCB or memory PCB and check for correct operation. |
| Error code: | C027 |
| Display: | CONTROLLER ROM |
| Description: | Controller ROM error • Final check sum error is detected during the printer starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Turn OFF the Power Switch of the printer and turn it ON again (Restart of the printer.) 2 Check the PWB-P connector for proper connection and correct as necessary. 3 If this error message is displayed after update of firmware, conduct the firmware update procedures again. 4 Change PWB-P. |
| Error code: | C050 |
| Display: | HDD ERROR |
| Description: | Optional second paper feeder communication problem • Communication fails five times successively. |
| Causes: | Paper feeder installed incorrectly. Defective main PCB or drawer main PCB. |
| Remedy: | Check the installation state of the paper feeder and adjust it if it is not properly installed. Replace the main PCB or drawer main PCB and check for correct operation. |
| Error code: | C051 |
| Display: | HDD DISK FULL |
| Description: | Optional third paper feeder communication problem • Communication fails five times successively. |
| Causes: | Paper feeder installed incorrectly. Defective main PCB or drawer main PCB. |
| Remedy: | Check the installation state of the paper feeder and adjust it if it is not properly installed. Replace the main PCB or drawer main PCB and check for correct operation. |
| Error code: | C052 |
| Display: | CARD ERROR |
| Description: | Compact Flash access error • When correct access to the Compact Flash is failed during access. |
| Causes: | MFP board (MFPB) Compact flash card |
| Remedy: | 1 Turn OFF the Power Switch of the printer and turn it ON again (Restart of the printer.) 2 Check the Compact Flash for proper connection and correct as necessary. 3 Check the PWB-P connector for proper connection and correct as necessary. 4 Change Compact Flash. 5 Change PWB-P. |
| Error code: | C053 |
| Display: | CARD FULL |
| Description: | Compact Flash full error • Range for user space is full during access to the Compact Flash. |
| Causes: | MFP board (MFPB) Compact flash card |
| Remedy: | 1 Turn OFF the Power Switch of the printer and turn it ON again (Restart of the printer.) 2 Check the Compact Flash for proper connection and correct as necessary. 3 Change Compact Flash. |
| Error code: | C054 |
| Display: | CARD ERROR |
| Description: | Compact Flash uninstallation • Compact Flash is not installed while accessing to the Compact Flash. |
| Causes: | MFP board (MFPB) Compact flash card |
| Remedy: | 1 Turn OFF the Power Switch of the printer and turn it ON again (Restart of the printer.) 2 Check the Compact Flash for proper connection and correct as necessary. 3 Check the PWB-P connector for proper connection and correct as necessary. 4 Change Compact Flash. 5 Change PWB-P. |
| Error code: | C060 |
| Display: | UPDATE ERROR |
| Description: | Detect hopping Motor lock error |
| Causes: | Hopping motor does not rotate nomary. |
| Remedy: | Power OFF/ON Turn off the Power of the printer and back on. |
| Error code: | C061 |
| Display: | HOLD JOB ERROR DUPLEX |
| Description: | Bitmap (DIMM) problem • There is a problem with the data or address bus of the bitmap DRAM. |
| Causes: | Defective main PCB. DIMM installed incorrectly. Defective DIMM. |
| Remedy: | Replace the main PCB and check for correct operation. Check if the DIMM is inserted into the socket on the main PCB correctly. Replace the DIMM and check for correct operation. |
| Error code: | C062 |
| Display: | HOLD JOB ERROR TRAY 3 |
| Description: | Memory input interface problem • Reading-in of an image does not complete within 10 s of the start of image transmission. |
| Causes: | Defective main PCB. |
| Remedy: | Replace the main PCB and check for correct operation. |
| Error code: | C063 |
| Display: | HOLD JOB ERROR TRAY 4 |
| Description: | DMA problem • DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time. |
| Causes: | Defective main PCB. |
| Remedy: | Replace the main PCB and check for correct operation. |
| Error code: | C064 |
| Display: | HOLD JOB ERROR MEMORY |
| Description: | Hold job error/No Memory • Expansion memory is not set when the expansion memory is required for printing of the job hold in HDD. |
| Remedy: | 1 Turn OFF the Power Switch of the printer and turn it ON again (Restart of the printer.) 2 Return to the same state as the device configuration when job was held. 3 Check the options that are mounted on the printer for proper connection and correct as necessary. 4 Check the PWB-M connector for proper connection and correct as necessary. 5 Delete the job hold in [PROOF/PRINT MENU]. |
| Error code: | C065 |
| Description: | Hold job error/No Tray 5 • Tray 5 is not set when the tray 5 is required for printing of the job hold in HDD. |
| Remedy: | 1 Turn OFF the Power Switch of the printer and turn it ON again (Restart of the printer.) 2 Return to the same state as the device configuration when job was held. 3 Check the options that are mounted on the printer for proper connection and correct as necessary. 4 Check the PWB-M connector for proper connection and correct as necessary. 5 Delete the job hold in [PROOF/PRINT MENU]. |
| Error code: | FFFF |
| Display: | I/F COMM ERROR |
| Description: | Interface Communication error • Correct communication is failed when receiving/sending the command between PWB-A and PWB-P. |
| Causes: | Print control board (PRCB) MFP board (MFPB) |
| Remedy: | 1 Turn OFF the Power Switch of the printer and turn it ON again (Restart of the printer.) 2 Check the PWB-P connector for proper connection and correct as necessary 3 Check the PWB-M connector for proper connection and correct as necessary. 4 Change PWB-M. |
Название
Konica Minolta Блок проявки черный
Konica Minolta Блок проявки желтый
Konica Minolta Блок проявки пурпурный
Konica Minolta Блок проявки голубой
Konica Minolta Емкость отработанного тонера
Konica Minolta Тонер-картридж черный
Konica Minolta Тонер-картридж желтый
Konica Minolta Тонер-картридж пурпурный
Konica Minolta Тонер-картридж голубой
