Konica-Minolta Magicolor 8650
Рейтинг
Модули
MAIN POWER SUPPLY UNIT
MANUAL FEED TRAY UNIT (Tray 1)
ADU/VERTICAL CONVEYANCE SECTION 5
REAR FAN SECTION
REAR ELECTRICAL SECTION
TRANSFER BELT UNIT
2ND PAPER FEED SECTION (Tray 3) 3
ADU/VERTICAL CONVEYANCE SECTION 4
PAPER EXIT SECTION 2
Toner collecting Section
HIGH VOLTAGE UNIT
MAIN FRAME SECTION
INNER COVER SECTION
1ST PAPER FEED SECTION (Tray 2)
2ND CASSETTE SECTION (Tray 3) 2
2ND CASSETTE SECTION (Tray 3)
Fusing Drive Section
LOWER FRAME SECTION
MAIN DRIVE SECTION
1ST CASSETTE SECTION (Tray 2)
2ND PAPER FEED SECTION (Tray 3) 2
EXTERNAL PARTS 2
ADU/VERTICAL CONVEYANCE SECTION 3
FUSING SECTION
MANUAL FEED TRAY UNIT (Tray 1) 3
P/H FRAME SECTION
2ND PAPER FEED SECTION (Tray 3)
PAPER EXIT SECTION
1ST CASSETTE SECTION (Tray 2) 2
FEED/TRANSPORT DRIVE SECTION
SIZE DETECTING SECTION
ERASE LAMP SECTION
MANUAL FEED TRAY UNIT (Tray 1) 4
TONER CONVEYANCE SECTION 2
T/C RAIL SECTION
TONER CONVEYANCE SECTION
PRINT HEAD SECTION
ADU/VERTICAL CONVEYANCE SECTION 2
1ST PAPER FEED SECTION (Tray 2) 2
ADU/VERTICAL CONVEYANCE SECTION
SHIELD BOX SECTION
MANUAL FEED TRAY UNIT (Tray 1) 2
EXTERNAL PARTS
Детали Toner collecting Section
| Деталь: | POWER SUPPLY |
| Парткод: | A02E M400 01 |
| Деталь: | POWER SUPPLY |
| Парткод: | A02E M401 01 |
| Деталь: | FAN MOTOR |
| Парткод: | A02E M108 01 |
| Деталь: | FILTER |
| Парткод: | A02E 1483 00 |
| Деталь: | FILTER |
| Парткод: | A02E 1484 00 |
| Деталь: | SHIELD |
| Парткод: | A02E 1480 03 |
| Деталь: | PLUG HOUSING |
| Парткод: | V818 6000 15 |
| Деталь: | Label Operation |
| Парткод: | A02E 9410 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5985 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 3446 01 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 5984 00 |
| Деталь: | SHAFT |
| Парткод: | 1134 3042 02 |
| Деталь: | TRAY |
| Парткод: | A02E 5911 00 |
| Деталь: | SEAL |
| Парткод: | A02E 5986 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | COVER |
| Парткод: | A02E 5918 01 |
| Деталь: | COVER |
| Парткод: | A02E 5909 01 |
| Деталь: | TRAY |
| Парткод: | A02E 5908 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J06 3286 02 |
| Деталь: | COVER |
| Парткод: | A02E 5906 00 |
| Деталь: | HOLD PLATE |
| Парткод: | 9J06 3215 02 |
| Деталь: | LABEL CAUTION |
| Парткод: | A02E 9411 00 |
| Деталь: | FRAME |
| Парткод: | A02E 5903 02 |
| Деталь: | BRACKET |
| Парткод: | 9J06 3235 01 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 5982 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 3234 02 |
| Деталь: | Caulking (Frame Right) |
| Парткод: | A02E G620 00 |
| Деталь: | COVER |
| Парткод: | A02E 5907 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 5910 00 |
| Деталь: | Sensor Wiring /1 |
| Парткод: | A02E N101 01 |
| Деталь: | Multiple Bypass Assy |
| Парткод: | A02E R716 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 7128 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 3559 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3537 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3539 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3538 01 |
| Деталь: | Label Jam/M1 |
| Парткод: | A02E 9406 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 7129 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 3536 01 |
| Деталь: | ROLLER |
| Парткод: | A02E 7001 00 |
| Деталь: | ROLLER |
| Парткод: | 4038 3502 02 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 7023 00 |
| Деталь: | FIXED POWER RESISTORS |
| Парткод: | V800 5003 00 |
| Деталь: | BUSHING |
| Парткод: | 4025 3572 01 |
| Деталь: | GEAR 20T |
| Парткод: | 4004 3503 02 |
| Деталь: | GEAR 14T |
| Парткод: | 4004 3504 02 |
| Деталь: | TENSION SPRING |
| Парткод: | 4038 3525 01 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 7130 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3567 01 |
| Деталь: | SEAL |
| Парткод: | 4128 3522 01 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A02E M505 00 |
| Деталь: | ACTUATOR |
| Парткод: | 4038 3562 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 1164 3527 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | BRACKET |
| Парткод: | 4038 3561 03 |
| Деталь: | HOLDER |
| Парткод: | A02E 7057 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 7126 01 |
| Деталь: | COVER |
| Парткод: | A02E 7058 01 |
| Деталь: | Photo sensing |
| Парткод: | A02E M500 00 |
| Деталь: | Toner Detection harness |
| Парткод: | A02E N10B 00 |
| Деталь: | SPACER |
| Парткод: | 4038 3597 01 |
| Деталь: | WASHER |
| Парткод: | 4038 3593 01 |
| Деталь: | FRAME |
| Парткод: | A02E 1006 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 4038 3592 01 |
| Деталь: | SPACER |
| Парткод: | 4038 5603 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A02E 7132 01 |
| Деталь: | CLUTCH |
| Парткод: | A02E M200 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 3540 03 |
| Деталь: | SHIELD BOX |
| Парткод: | A02E 1451 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | DUCT |
| Парткод: | A02E 1149 01 |
| Деталь: | DUCT |
| Парткод: | A02E 1150 00 |
| Деталь: | Cooling Wiring /C |
| Парткод: | A02E N111 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1400 31 |
| Деталь: | DUCT |
| Парткод: | A02E 1487 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1454 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 1456 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1457 01 |
| Деталь: | COVER |
| Парткод: | A02E 1458 00 |
| Деталь: | PROTECTION |
| Парткод: | 1154 4670 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 1462 00 |
| Деталь: | PFU Relay harness |
| Парткод: | A02E N10J 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1472 01 |
| Деталь: | LABEL |
| Парткод: | 9J06 7301 01 |
| Деталь: | LABEL |
| Парткод: | 9J06 7302 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 1471 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 1493 01 |
| Деталь: | Power Supply Wiring |
| Парткод: | A02E N125 01 |
| Деталь: | BRACKET |
| Парткод: | 4037 2239 02 |
| Деталь: | POWER CORD |
| Парткод: | 4037 0775 01 |
| Деталь: | FNS Relay harness |
| Парткод: | A02E N10E 00 |
| Деталь: | FRAME |
| Парткод: | A02E 1252 01 |
| Деталь: | AC Wiring /120V |
| Парткод: | A02E N121 02 |
| Деталь: | AC Wiring /230V |
| Парткод: | A02E N124 01 |
| Деталь: | AC Wiring /100V |
| Парткод: | A02E N120 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 1498 00 |
| Деталь: | Transfer Detection Assy |
| Парткод: | A02E R708 11 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 1123 00 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 1122 12 |
| Деталь: | BRACKET |
| Парткод: | A02E 1121 11 |
| Деталь: | Connecting Detection harness |
| Парткод: | A02E N114 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | Transfer Wiring /14 |
| Парткод: | A02E N131 00 |
| Деталь: | Transfer Wiring /13 |
| Парткод: | A02E N132 01 |
| Деталь: | Transfer Wiring /2 |
| Парткод: | A02E N130 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | ARM |
| Парткод: | 4038 2027 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2029 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2028 01 |
| Деталь: | LEVER |
| Парткод: | 4038 2026 01 |
| Деталь: | CONTACT |
| Парткод: | A02E 1103 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2205 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2207 01 |
| Деталь: | CONTACT |
| Парткод: | A02E 1104 00 |
| Деталь: | CONTACT |
| Парткод: | A02E 1105 00 |
| Деталь: | RAIL |
| Парткод: | A02E 1102 00 |
| Деталь: | CONTACT |
| Парткод: | A02E 1107 00 |
| Деталь: | RAIL |
| Парткод: | A02E 1101 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2152 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2077 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2078 13 |
| Деталь: | CONTACT |
| Парткод: | 4038 2153 13 |
| Деталь: | LEVER |
| Парткод: | 4038 2046 01 |
| Деталь: | ARM |
| Парткод: | 4038 2047 02 |
| Деталь: | CONTACT |
| Парткод: | 4038 2080 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2045 01 |
| Деталь: | CONTACT |
| Парткод: | A02E 1108 00 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2048 01 |
| Деталь: | Transfer Belt Kit |
| Парткод: | A02E R735 11 |
| Деталь: | DETECTING PLATE |
| Парткод: | A02E 5033 01 |
| Деталь: | DOOR |
| Парткод: | A02E 5871 13 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3123 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4348 3058 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 5882 00 |
| Деталь: | CLAW |
| Парткод: | A02E 5875 00 |
| Деталь: | ROLL |
| Парткод: | 4030 3122 01 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 5874 00 |
| Деталь: | CLAW |
| Парткод: | A02E 5876 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A02E 5879 01 |
| Деталь: | BRACKET |
| Парткод: | 4348 3054 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 5872 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 5842 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 5880 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | ROLLER |
| Парткод: | A02E 5841 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 5881 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M200 00 |
| Деталь: | Gear 26/34T |
| Парткод: | A02E 5693 01 |
| Деталь: | Gear 23/28T |
| Парткод: | A02E 5804 00 |
| Деталь: | Gear 20/31T |
| Парткод: | A02E 5805 00 |
| Деталь: | Caulking (Drive Reinforce) |
| Парткод: | A02E G571 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 7113 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 3511 02 |
| Деталь: | STOPPER |
| Парткод: | A02E 7123 00 |
| Деталь: | COLLAR |
| Парткод: | A02E 7115 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 7111 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 7114 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 7112 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 7117 01 |
| Деталь: | Label JAM |
| Парткод: | A02E 9405 00 |
| Деталь: | SHAFT |
| Парткод: | 4038 3516 01 |
| Деталь: | CUSHION |
| Парткод: | A02E 7140 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 8954 00 |
| Деталь: | Stepping motor |
| Парткод: | A02E M10C 01 |
| Деталь: | Caulking Mounting Plate |
| Парткод: | A02E G213 00 |
| Деталь: | LEVER |
| Парткод: | A02E 8956 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 8957 01 |
| Деталь: | HOUSING |
| Парткод: | A02E 8950 00 |
| Деталь: | Gear 36/59T |
| Парткод: | A02E 8951 00 |
| Деталь: | ROLLER |
| Парткод: | A02E 8910 00 |
| Деталь: | ROLL |
| Парткод: | 4131 3904 02 |
| Деталь: | BUSHING |
| Парткод: | 4038 5860 01 |
| Деталь: | SHAFT |
| Парткод: | 4025 5984 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | SPACER |
| Парткод: | A02E 8916 00 |
| Деталь: | COVER |
| Парткод: | A02E 8903 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 8906 00 |
| Деталь: | Gear16T |
| Парткод: | A02E 8952 00 |
| Деталь: | Waste Toner Box |
| Парткод: | A0DT 01A |
| Деталь: | Waste Toner Box |
| Парткод: | A0DT 0YA |
| Деталь: | RAIL |
| Парткод: | A02E 3650 01 |
| Деталь: | COVER |
| Парткод: | A02E 3651 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0901 01 |
| Деталь: | Sensor Wiring /3 |
| Парткод: | A02E N10G 00 |
| Деталь: | SHUTTER |
| Парткод: | A02E 3641 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 3644 01 |
| Деталь: | PIPE |
| Парткод: | A02E 3640 01 |
| Деталь: | SEAL |
| Парткод: | A02E 3643 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3642 01 |
| Деталь: | HIGH VOLTAGE UNIT |
| Парткод: | A02E M402 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 1329 00 |
| Деталь: | IU Contact Assy Black |
| Парткод: | A02E R700 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2222 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2233 02 |
| Деталь: | BRACKET |
| Парткод: | A02E 1322 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1328 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1321 01 |
| Деталь: | COVER |
| Парткод: | A02E 1327 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2203 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2225 02 |
| Деталь: | CONTACT |
| Парткод: | A02E 1332 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 1323 01 |
| Деталь: | CONTACT |
| Парткод: | A02E 1333 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2276 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 1324 00 |
| Деталь: | IU Contact Assy CMY |
| Парткод: | A02E R732 00 |
| Деталь: | INSULATING MEMBER |
| Парткод: | A02E 1194 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 1193 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1192 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 1191 00 |
| Деталь: | HANDLE |
| Парткод: | A02E 1190 01 |
| Деталь: | CAP |
| Парткод: | A02E 1196 00 |
| Деталь: | SEAL |
| Парткод: | 4039 2209 01 |
| Деталь: | SEAL |
| Парткод: | A02E 1207 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1382 00 |
| Деталь: | DUCT |
| Парткод: | A02E 1206 01 |
| Деталь: | DUCT |
| Парткод: | A02E 1201 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1014 00 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996 3055 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 1203 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1300 51 |
| Деталь: | Front Cover Switch Assy |
| Парткод: | A02E R709 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1381 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 2287 02 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 1384 00 |
| Деталь: | Heater Relay harness |
| Парткод: | A02E N122 01 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06 M601 00 |
| Деталь: | Supply Detection harness |
| Парткод: | A02E N10N 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 2281 04 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2282 03 |
| Деталь: | CONNECTOR PIN |
| Парткод: | V816 3000 02 |
| Деталь: | COVER |
| Парткод: | 9J06 2460 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2283 02 |
| Деталь: | CONNECTOR |
| Парткод: | V651 0100 40 |
| Деталь: | COVER |
| Парткод: | A02E 1702 00 |
| Деталь: | SUCTION PLATE |
| Парткод: | A02E 1614 01 |
| Деталь: | SPACER |
| Парткод: | A02E 1618 00 |
| Деталь: | Label Iu |
| Парткод: | A02E 9403 00 |
| Деталь: | Label Tc/Iu |
| Парткод: | A02E 9402 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 1703 00 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038 1014 01 |
| Деталь: | Photoconductor Detection harness |
| Парткод: | A02E N119 02 |
| Деталь: | POWER SOURCE SWITCH |
| Парткод: | A02E M601 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1383 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | AC Power source harness |
| Парткод: | A02E N123 00 |
| Деталь: | DUCT |
| Парткод: | A02E 1161 02 |
| Деталь: | SEAL |
| Парткод: | A02E 1167 00 |
| Деталь: | HEAT SINK |
| Парткод: | A02E 1166 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1205 00 |
| Деталь: | COVER |
| Парткод: | A02E 1701 00 |
| Деталь: | COVER |
| Парткод: | A02E 1050 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M202 00 |
| Деталь: | Caulking Rear Frame/Paper Feed |
| Парткод: | A02E G560 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5606 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | Conveyance Wiring /1 |
| Парткод: | A02E N105 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A02E R904 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 5612 00 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3016 12 |
| Деталь: | FRAME |
| Парткод: | A02E 5601 01 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E 5611 00 |
| Деталь: | GEAR 30T |
| Парткод: | 4425 3013 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | SHAFT |
| Парткод: | 4040 3097 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 3030 01 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | LEVER |
| Парткод: | A02E 5613 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 5614 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 5608 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 5605 00 |
| Деталь: | SHAFT |
| Парткод: | 4030 3003 01 |
| Деталь: | GEAR 29T |
| Парткод: | 4030 3008 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 5755 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 5604 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 5607 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5609 00 |
| Деталь: | FRAME |
| Парткод: | A02E 5603 00 |
| Деталь: | GUIDE |
| Парткод: | 4537 3317 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | LABEL CARRYING CAPACITY |
| Парткод: | 4002 7306 01 |
| Деталь: | Lock Shaft |
| Парткод: | A00J 6222 00 |
| Деталь: | CUSHION |
| Парткод: | A02E 6227 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030 3214 02 |
| Деталь: | GUIDE |
| Парткод: | 4030 3215 01 |
| Деталь: | GEAR 14T |
| Парткод: | A02E 6224 00 |
| Деталь: | CUSHION |
| Парткод: | A02E 6233 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 6209 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 6208 01 |
| Деталь: | KNOB |
| Парткод: | 4037 3204 01 |
| Деталь: | SHAFT |
| Парткод: | 4498 3826 01 |
| Деталь: | LEVER |
| Парткод: | 4128 3823 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4498 3825 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 6210 00 |
| Деталь: | BUSHING |
| Парткод: | 0992 3014 01 |
| Деталь: | Label Paper supply |
| Парткод: | A02E 9412 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 6220 00 |
| Деталь: | BUSHING |
| Парткод: | 1274 3603 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3021 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3020 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3207 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 6216 00 |
| Деталь: | LEVER |
| Парткод: | 4030 3206 01 |
| Деталь: | FRICTION PLATE |
| Парткод: | A00J 6234 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030 3226 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | A02E 6218 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 6206 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 6213 00 |
| Деталь: | SCREW |
| Парткод: | 4498 3834 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 6219 00 |
| Деталь: | COVER |
| Парткод: | A02E 6330 01 |
| Деталь: | Label Cd |
| Парткод: | A00J 9421 02 |
| Деталь: | Label FD |
| Парткод: | A00J 9423 02 |
| Деталь: | CASSETTE |
| Парткод: | A02E 6301 03 |
| Деталь: | LEVER |
| Парткод: | A02E 6214 00 |
| Деталь: | STOPPER |
| Парткод: | 4498 3469 01 |
| Деталь: | Label FD |
| Парткод: | A00J 9422 02 |
| Деталь: | REGULATING PLATE ASSY |
| Парткод: | A02E R734 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 6223 00 |
| Деталь: | GUIDE |
| Парткод: | 4030 3228 12 |
| Деталь: | EARTH GROUND |
| Парткод: | 4030 3223 03 |
| Деталь: | WASHER |
| Парткод: | A02E 2303 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A02E 2585 00 |
| Деталь: | WASHER |
| Парткод: | A02E 2302 00 |
| Деталь: | Gear 27/85T |
| Парткод: | A02E 2570 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | SHAFT |
| Парткод: | A02E 2573 00 |
| Деталь: | PIN |
| Парткод: | 1144 5200 01 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 01 |
| Деталь: | GEAR 34T |
| Парткод: | A02E 2571 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 2582 00 |
| Деталь: | MOTOR ASSY |
| Парткод: | A02E R714 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 2310 11 |
| Деталь: | Gear 18/75T |
| Парткод: | A02E 2542 00 |
| Деталь: | Gear 17/68T |
| Парткод: | A02E 2544 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2314 00 |
| Деталь: | Gear 16/29T |
| Парткод: | A02E 2591 00 |
| Деталь: | LEVER |
| Парткод: | A02E 2584 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 2557 12 |
| Деталь: | GEAR 16T |
| Парткод: | 9J06 2574 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 2587 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 9J06 2595 02 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2580 01 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 2312 00 |
| Деталь: | GEAR 13T |
| Парткод: | 9J06 2546 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 2576 01 |
| Деталь: | GEAR 22T |
| Парткод: | 9J06 2575 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 2594 00 |
| Деталь: | GEAR 18T |
| Парткод: | 4038 2592 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 2596 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M200 00 |
| Деталь: | PIN |
| Парткод: | 4131 2536 02 |
| Деталь: | GEAR 41T |
| Парткод: | 4038 2593 02 |
| Деталь: | SHAFT |
| Парткод: | A02E 2563 00 |
| Деталь: | GEAR 40T |
| Парткод: | A02E 2545 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2316 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2315 00 |
| Деталь: | GEAR 60T |
| Парткод: | 9J06 2543 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 2556 12 |
| Деталь: | PLUG HOUSING |
| Парткод: | V818 6000 14 |
| Деталь: | HOLDER |
| Парткод: | 9J06 2572 01 |
| Деталь: | Brushless motor |
| Парткод: | A02E M100 00 |
| Деталь: | BUSHING |
| Парткод: | 9J06 2101 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313 1000 72 |
| Деталь: | SEAL |
| Парткод: | A02E 1173 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1175 01 |
| Деталь: | OZONE FILTER |
| Парткод: | A02E R736 00 |
| Деталь: | DUCT |
| Парткод: | A02E 1172 00 |
| Деталь: | SEAL |
| Парткод: | 4038 2062 01 |
| Деталь: | PLATE SPRING |
| Парткод: | A02E 6228 01 Old |
| Деталь: | PLATE SPRING |
| Парткод: | A02E 6228 12 |
| Деталь: | SPACER |
| Парткод: | A02E 6225 01 Old |
| Деталь: | SPACER |
| Парткод: | A02E 6225 12 |
| Деталь: | RAIL |
| Парткод: | A02E 1009 02 |
| Деталь: | BRACKET |
| Парткод: | A02E 1029 00 |
| Деталь: | CONTACT |
| Парткод: | 4038 2099 01 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3541 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 1013 01 |
| Деталь: | STOPPER |
| Парткод: | A02E 1049 01 |
| Деталь: | RAIL |
| Парткод: | A02E 1030 00 |
| Деталь: | PWB Assembly LED1 |
| Парткод: | A00J H00D 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 1634 00 |
| Деталь: | Lens /A |
| Парткод: | A00J 1681 02 |
| Деталь: | SHIELD PLATE |
| Парткод: | A02E 1642 00 |
| Деталь: | COVER |
| Парткод: | A02E 1649 01 |
| Деталь: | Label Number 2 |
| Парткод: | A02E 9433 00 |
| Деталь: | Label Number 3 |
| Парткод: | A02E 9434 00 |
| Деталь: | Indicating Wiring |
| Парткод: | A02E N110 01 |
| Деталь: | RUBBER FOOT |
| Парткод: | 0996 3055 01 |
| Деталь: | RAIL |
| Парткод: | A02E 1015 01 |
| Деталь: | RAIL |
| Парткод: | A02E 1017 02 |
| Деталь: | RAIL |
| Парткод: | A02E 1007 00 |
| Деталь: | PLATE NUT |
| Парткод: | A02E 1021 00 |
| Деталь: | CUSHION |
| Парткод: | 4038 2162 02 |
| Деталь: | DUCT |
| Парткод: | A02E 1154 00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | DUCT |
| Парткод: | A02E 1151 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 1156 00 |
| Деталь: | SEAL |
| Парткод: | 4038 2098 01 |
| Деталь: | DUCT |
| Парткод: | A02E 1153 00 |
| Деталь: | GEAR 36T |
| Парткод: | A02E 2518 00 |
| Деталь: | PIN |
| Парткод: | A02E 2290 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 1106 00 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A02E R715 00 |
| Деталь: | Brushless motor |
| Парткод: | A02E M103 00 |
| Деталь: | Hopper Drive Assy 2 |
| Парткод: | A02E R711 00 |
| Деталь: | Hopper Drive Assy 1 |
| Парткод: | A02E R710 00 |
| Деталь: | FRICTION PLATE |
| Парткод: | A00J 6234 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030 3226 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | A02E 6218 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 6206 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 6213 00 |
| Деталь: | SCREW |
| Парткод: | 4498 3834 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 6219 00 |
| Деталь: | COVER |
| Парткод: | A02E 6231 01 |
| Деталь: | COVER |
| Парткод: | A02E 6230 01 |
| Деталь: | LEVER |
| Парткод: | 4002 3108 01 |
| Деталь: | CASSETTE |
| Парткод: | A02E 6201 04 |
| Деталь: | Label FD |
| Парткод: | A02E 9413 00 |
| Деталь: | Label Cd |
| Парткод: | A02E 9415 00 |
| Деталь: | Label FD |
| Парткод: | A00J 9422 02 |
| Деталь: | EARTH GROUND |
| Парткод: | 4030 3223 03 |
| Деталь: | GUIDE |
| Парткод: | 4030 3228 12 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 6223 00 |
| Деталь: | REGULATING PLATE ASSY |
| Парткод: | A02E R734 00 |
| Деталь: | BRAKE |
| Парткод: | A02E 6234 00 |
| Деталь: | RAIL |
| Парткод: | A02E 6226 00 |
| Деталь: | STOPPER |
| Парткод: | 4498 3469 01 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A02E R729 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5636 00 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A02E F566 00 |
| Деталь: | LEVER |
| Парткод: | 4030 3078 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | BRACKET |
| Парткод: | 4030 3014 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3017 03 |
| Деталь: | HOLDER |
| Парткод: | 4030 3013 01 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3125 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 5772 00 |
| Деталь: | GUIDE |
| Парткод: | 4030 3105 01 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 5843 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 5610 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5771 00 |
| Деталь: | COVER |
| Парткод: | A02E 1663 02 |
| Деталь: | COVER |
| Парткод: | A02E 1662 04 |
| Деталь: | COVER |
| Парткод: | A02E 1711 00 |
| Деталь: | FILTER |
| Парткод: | A02E 1152 00 |
| Деталь: | COVER |
| Парткод: | A02E 1636 01 |
| Деталь: | COVER |
| Парткод: | A02E 1629 00 |
| Деталь: | COVER |
| Парткод: | A02E 1646 00 |
| Деталь: | COVER |
| Парткод: | A02E 1630 00 |
| Деталь: | COVER |
| Парткод: | A02E 1712 00 |
| Деталь: | COVER |
| Парткод: | A02E 1713 00 |
| Деталь: | LABEL OUTLET |
| Парткод: | 4037 7407 01 |
| Деталь: | COVER |
| Парткод: | A02E 1651 00 |
| Деталь: | COVER |
| Парткод: | A02E 1710 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 7191 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 7192 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 7109 00 |
| Деталь: | LEVER |
| Парткод: | A02E 7100 00 |
| Деталь: | CAM |
| Парткод: | 4038 3553 01 |
| Деталь: | LEVER |
| Парткод: | A02E 7051 01 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 7053 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 4620 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 4611 01 |
| Деталь: | HOLDER |
| Парткод: | 4038 3542 02 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 3520 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 7107 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 3571 02 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 7054 00 |
| Деталь: | LEVER |
| Парткод: | A02E 7052 01 |
| Деталь: | TRANSFER ROLLER UNIT |
| Парткод: | A02E R713 00 |
| Деталь: | Fusing Unit 100V |
| Парткод: | A02E R718 11 |
| Деталь: | FUSING UNIT 120V |
| Парткод: | A02E R720 11 |
| Деталь: | FUSING UNIT 230V |
| Парткод: | A02E R721 11 |
| Деталь: | FUSING UNIT 110V |
| Парткод: | A02E R733 11 |
| Деталь: | HOLDER |
| Парткод: | 9J06 2082 01 |
| Деталь: | GUIDE |
| Парткод: | 9J06 2462 01 |
| Деталь: | HOLDER |
| Парткод: | 9J06 2079 01 |
| Деталь: | SEAL |
| Парткод: | A02E 1057 01 |
| Деталь: | GUIDE |
| Парткод: | 9J06 2463 02 |
| Деталь: | COVER |
| Парткод: | A02E 5912 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5941 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5913 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | 4030 3402 01 |
| Деталь: | SEAL |
| Парткод: | 4030 3489 01 |
| Деталь: | GUIDE |
| Парткод: | 4030 3403 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 5973 01 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | 4034 0151 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 5976 00 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A02E R717 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 5971 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3475 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 5972 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 3270 01 |
| Деталь: | GUIDE |
| Парткод: | 4038 3269 02 |
| Деталь: | GUIDE |
| Парткод: | 4038 3268 02 |
| Деталь: | GUIDE |
| Парткод: | A02E 5901 00 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 5974 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 5945 00 |
| Деталь: | LEVER |
| Парткод: | A02E 5946 00 |
| Деталь: | TENSION SPRING |
| Парткод: | A02E 5943 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5942 00 |
| Деталь: | RESISTOR |
| Парткод: | 9455 8076 01 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 5975 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5915 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5902 00 |
| Деталь: | Gear18T |
| Парткод: | A02E 5968 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 5967 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5966 00 |
| Деталь: | GEAR 22T |
| Парткод: | A02E 5955 00 |
| Деталь: | SEAL |
| Парткод: | 4038 2051 01 |
| Деталь: | SEAL |
| Парткод: | A02E 1179 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J06 2086 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 1055 00 |
| Деталь: | PWB assembly (PWB-PH ASSY) |
| Парткод: | A02E H003 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 1330 00 |
| Деталь: | PU Lifting Plate Assy |
| Парткод: | A02E R704 00 |
| Деталь: | ROLL |
| Парткод: | 4038 2094 01 |
| Деталь: | LIFTING PLATE |
| Парткод: | 4038 2016 02 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A02E 1058 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2018 03 |
| Деталь: | BRACKET |
| Парткод: | 4038 2061 01 |
| Деталь: | ATDC Connector Assy |
| Парткод: | A02E R705 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M202 00 |
| Деталь: | Caulking Rear Frame/Paper Feed2 |
| Парткод: | A02E G570 00 |
| Деталь: | COVER |
| Парткод: | A02E 5753 00 |
| Деталь: | Conveyance Wiring /2 |
| Парткод: | A02E N106 02 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A02E R904 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5791 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 5612 00 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3016 12 |
| Деталь: | BUSHING |
| Парткод: | 4131 3003 01 |
| Деталь: | FRAME |
| Парткод: | A02E 5751 03 |
| Деталь: | ROLLER |
| Парткод: | A00J 5636 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E 5611 00 |
| Деталь: | GEAR 30T |
| Парткод: | 4425 3013 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 5607 00 |
| Деталь: | SHAFT |
| Парткод: | 4040 3097 01 |
| Деталь: | GEAR 29T |
| Парткод: | 4030 3008 01 |
| Деталь: | GEAR 32T |
| Парткод: | 4425 3016 01 |
| Деталь: | SHAFT |
| Парткод: | 4030 3003 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4030 3030 01 |
| Деталь: | BUSHING |
| Парткод: | 1065 3086 01 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 5605 00 |
| Деталь: | LEVER |
| Парткод: | A02E 5613 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 5614 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 5608 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5609 00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A02E 5754 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5755 01 |
| Деталь: | FRAME |
| Парткод: | A02E 5603 00 |
| Деталь: | COVER |
| Парткод: | A02E 8920 02 |
| Деталь: | Neutralizing Brush |
| Парткод: | A02E 8923 00 |
| Деталь: | Neutralizing Brush |
| Парткод: | A02E 8922 00 |
| Деталь: | Cooling Wiring /1 |
| Парткод: | A02E N109 01 |
| Деталь: | Neutralizing Brush |
| Парткод: | A02E 8921 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03 M100 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 8904 03 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 8934 00 |
| Деталь: | EARTH GROUND |
| Парткод: | 4038 5886 03 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 8905 00 |
| Деталь: | PIN |
| Парткод: | 4036 2549 01 |
| Деталь: | COLLAR |
| Парткод: | A02E 8913 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 8902 03 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 8925 00 |
| Деталь: | SPACER |
| Парткод: | A02E 8933 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 8929 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 8924 01 |
| Деталь: | ACTUATOR |
| Парткод: | A02E 8928 01 |
| Деталь: | Sensor Wiring /P |
| Парткод: | A02E N11D 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | BRACKET |
| Парткод: | A02E 8926 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 8927 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 6216 00 |
| Деталь: | LEVER |
| Парткод: | 4030 3206 01 |
| Деталь: | ACTUATOR |
| Парткод: | 4030 3207 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3021 01 |
| Деталь: | WASHER |
| Парткод: | 4011 3020 01 |
| Деталь: | BUSHING |
| Парткод: | 1274 3603 01 |
| Деталь: | CUSHION |
| Парткод: | A02E 6233 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 6209 00 |
| Деталь: | GUIDE |
| Парткод: | 4537 3317 01 |
| Деталь: | LABEL CARRYING CAPACITY |
| Парткод: | 4002 7306 01 |
| Деталь: | CUSHION |
| Парткод: | A02E 6227 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | Lock Shaft |
| Парткод: | A00J 6222 00 |
| Деталь: | GEAR 14T |
| Парткод: | A02E 6224 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030 3214 02 |
| Деталь: | GUIDE |
| Парткод: | 4030 3215 01 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 6208 01 |
| Деталь: | KNOB |
| Парткод: | 4037 3204 01 |
| Деталь: | SHAFT |
| Парткод: | 4498 3826 01 |
| Деталь: | LEVER |
| Парткод: | 4128 3823 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4498 3825 01 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 6210 00 |
| Деталь: | BUSHING |
| Парткод: | 0992 3014 01 |
| Деталь: | Label Paper supply |
| Парткод: | A02E 9412 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 6220 00 |
| Деталь: | HOLDER |
| Парткод: | 4038 2275 01 |
| Деталь: | BUSHING |
| Парткод: | 1200 3121 09 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 2597 00 |
| Деталь: | PIN |
| Парткод: | A02E 2290 00 |
| Деталь: | Gear 83/115T |
| Парткод: | A02E 2513 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2524 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2535 02 |
| Деталь: | GEAR 32T |
| Парткод: | A02E 2599 00 |
| Деталь: | GEAR 18/30T |
| Парткод: | 4004 2545 01 |
| Деталь: | GEAR 26T |
| Парткод: | A02E 2529 00 |
| Деталь: | GEAR 22T |
| Парткод: | A02E 2519 00 |
| Деталь: | Gear18T |
| Парткод: | A02E 2598 01 |
| Деталь: | PIN |
| Парткод: | 4131 2536 02 |
| Деталь: | GEAR 27T |
| Парткод: | A02E 2202 00 |
| Деталь: | BUSHING |
| Парткод: | 9J06 2101 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2515 00 |
| Деталь: | BUSHING |
| Парткод: | 4658 3516 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 2526 02 |
| Деталь: | Gear 23T |
| Парткод: | A02E 2201 00 |
| Деталь: | GEAR 30T |
| Парткод: | A02E 2532 00 |
| Деталь: | Gear 24/32T |
| Парткод: | A02E 2531 00 |
| Деталь: | Gear 65T |
| Парткод: | A02E 2520 01 |
| Деталь: | GEAR 20/56T |
| Парткод: | 4038 2578 01 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 2539 00 |
| Деталь: | Gear 42/56T |
| Парткод: | A02E 2508 00 |
| Деталь: | Gear 22/46T |
| Парткод: | A02E 2517 00 |
| Деталь: | Gear 46/53T |
| Парткод: | A02E 2551 00 |
| Деталь: | Gear 50/56T |
| Парткод: | A02E 2549 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 2523 01 |
| Деталь: | Gear 50T |
| Парткод: | A02E 2514 00 |
| Деталь: | CLUTCH |
| Парткод: | A02E M203 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 2536 00 |
| Деталь: | Feed/Transport Drive Assy |
| Парткод: | A02E R712 00 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4002 3131 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4002 3110 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | MOTOR |
| Парткод: | 9J06 M103 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | BRACKET |
| Парткод: | A02E 5721 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3081 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030 3224 02 |
| Деталь: | HOLDER |
| Парткод: | 4030 3083 01 |
| Деталь: | GEAR 25T |
| Парткод: | A02E 2204 00 |
| Деталь: | Gear 24/24T |
| Парткод: | A02E 2205 00 |
| Деталь: | Gear 27/32T |
| Парткод: | A02E 2206 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 2211 00 |
| Деталь: | Gear 26/27T |
| Парткод: | A02E 2209 00 |
| Деталь: | Gear 27/34T |
| Парткод: | A02E 2208 00 |
| Деталь: | Gear 31T |
| Парткод: | A02E 2207 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 2210 00 |
| Деталь: | Paperfeed Wiring /1 |
| Парткод: | A02E N10C 00 |
| Деталь: | LEVER |
| Парткод: | 4030 3091 01 |
| Деталь: | PWB ASSY |
| Парткод: | 4037 0104 01 |
| Деталь: | HOLDER |
| Парткод: | 4030 3047 02 |
| Деталь: | HOLDER |
| Парткод: | 4011 3012 01 |
| Деталь: | Paperfeed Wiring /2 |
| Парткод: | A02E N10D 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5831 00 |
| Деталь: | Eraser Assy Black |
| Парткод: | A02E R706 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1033 11 |
| Деталь: | SHIELD PLATE |
| Парткод: | A02E 1053 11 |
| Деталь: | LED ARRAY |
| Парткод: | A02E M304 00 |
| Деталь: | Eraser Assy YMC |
| Парткод: | A02E R707 00 |
| Деталь: | COVER |
| Парткод: | A02E 1054 00 |
| Деталь: | SHIELD PLATE |
| Парткод: | A02E 1051 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 1035 00 |
| Деталь: | SEAL |
| Парткод: | 9J06 2472 00 |
| Деталь: | RAIL |
| Парткод: | A02E 1034 00 |
| Деталь: | SEAL |
| Парткод: | 9J06 2461 01 |
| Деталь: | RAIL |
| Парткод: | A02E 1037 00 |
| Деталь: | Label lu |
| Парткод: | A02E 9403 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 2072 04 |
| Деталь: | SLlDER |
| Парткод: | 4038 2069 01 |
| Деталь: | SEAL |
| Парткод: | A02E 1204 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5956 00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | CLUTCH |
| Парткод: | A02E M201 00 |
| Деталь: | GEAR 30T |
| Парткод: | A02E 5961 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5952 01 |
| Деталь: | SHIELD PLATE |
| Парткод: | 4038 3237 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 5953 01 Old |
| Деталь: | SHAFT |
| Парткод: | A02E 5953 02 |
| Деталь: | CLUTCH ASSY |
| Парткод: | A02E 5951 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 5963 00 |
| Деталь: | CAM |
| Парткод: | A02E 5960 01 Old |
| Деталь: | CAM |
| Парткод: | A02E 5960 02 |
| Деталь: | SHAFT |
| Парткод: | A02E 5957 00 |
| Деталь: | STOP RING |
| Парткод: | 4142 3217 01 |
| Деталь: | FEED ROLLER |
| Парткод: | A02E 5947 00 |
| Деталь: | GEAR 22T |
| Парткод: | A02E 5954 00 |
| Деталь: | BUSHING |
| Парткод: | 4131 3532 02 |
| Деталь: | SOLENOID |
| Парткод: | 9J06 M200 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 3616 01 |
| Деталь: | COVER |
| Парткод: | A02E 3615 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3619 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 3614 00 |
| Деталь: | GEAR 22T |
| Парткод: | A02E 3626 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 3625 00 |
| Деталь: | COIL |
| Парткод: | A02E 3613 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3617 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 3618 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 2452 01 |
| Деталь: | GEAR 35T |
| Парткод: | A02E 2451 00 |
| Деталь: | BUSHING |
| Парткод: | 4004 5339 01 |
| Деталь: | HOLDER |
| Парткод: | A02E 2586 01 |
| Деталь: | Gear 26/34T |
| Парткод: | A02E 2450 00 |
| Деталь: | Gear 30/30T |
| Парткод: | A02E 2579 00 |
| Деталь: | GEAR 18/30T |
| Парткод: | 4004 2545 01 |
| Деталь: | SHAFT |
| Парткод: | A02E 2453 02 |
| Деталь: | PIPE |
| Парткод: | A02E 3611 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2143 01 |
| Деталь: | TORSION SPRING |
| Парткод: | 4038 2114 01 |
| Деталь: | SHUTTER |
| Парткод: | A02E 3628 00 |
| Деталь: | CAP |
| Парткод: | A02E 3631 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 3634 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1481 00 |
| Деталь: | Gear18T |
| Парткод: | A02E 3627 00 |
| Деталь: | GEAR 41T |
| Парткод: | A02E 3635 00 |
| Деталь: | Gear 27/48T |
| Парткод: | A02E 3622 00 |
| Деталь: | Caulking (Drive) |
| Парткод: | A02E G210 00 |
| Деталь: | Gear 32/43T |
| Парткод: | A02E 3636 00 |
| Деталь: | Gear 22/37T |
| Парткод: | A02E 3630 00 |
| Деталь: | SET PLATE |
| Парткод: | 4038 2038 02 |
| Деталь: | RAIL |
| Парткод: | A02E 1019 02 |
| Деталь: | LABEL |
| Парткод: | 4038 7316 01 |
| Деталь: | CLAW |
| Парткод: | A02E 1080 00 |
| Деталь: | CLAW |
| Парткод: | A02E 1081 00 |
| Деталь: | CLAW |
| Парткод: | A02E 1082 00 |
| Деталь: | CLAW |
| Парткод: | A02E 1084 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3662 01 |
| Деталь: | SEAL |
| Парткод: | A02E 3661 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 3660 01 |
| Деталь: | SEAL |
| Парткод: | 4038 2110 03 |
| Деталь: | RAIL |
| Парткод: | A02E 1022 00 |
| Деталь: | RAIL |
| Парткод: | A02E 1025 00 |
| Деталь: | RAIL |
| Парткод: | A02E 1026 00 |
| Деталь: | Gear15T |
| Парткод: | A02E 3676 00 |
| Деталь: | Gear14T |
| Парткод: | A02E 3677 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 3682 01 |
| Деталь: | WASHER |
| Парткод: | A02E 3687 00 |
| Деталь: | SCREW |
| Парткод: | A02E 3674 01 |
| Деталь: | SEAL |
| Парткод: | A02E 3684 00 |
| Деталь: | Transport Pipe K |
| Парткод: | A02E 3673 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 3681 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3679 01 |
| Деталь: | INSULATING MEMBER |
| Парткод: | A02E 1047 00 |
| Деталь: | SEAL |
| Парткод: | 4038 2056 02 |
| Деталь: | DUCT |
| Парткод: | 4038 2052 02 |
| Деталь: | SEAL |
| Парткод: | 4038 2053 02 |
| Деталь: | SHUTTER |
| Парткод: | A02E 3603 00 |
| Деталь: | SEAL |
| Парткод: | A02E 3604 00 |
| Деталь: | TORSION SPRING |
| Парткод: | A02E 3602 00 |
| Деталь: | PIPE |
| Парткод: | A02E 3601 01 |
| Деталь: | SCREW |
| Парткод: | A02E 3671 01 |
| Деталь: | Transport Pipe CMY |
| Парткод: | A02E 3670 00 |
| Деталь: | Gear18T |
| Парткод: | A02E 3637 00 |
| Деталь: | BUSHING |
| Парткод: | A02E 3683 00 |
| Деталь: | PIN |
| Парткод: | A02E 3678 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 3680 00 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | A02E R701 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038 1906 04 |
| Деталь: | BRACKET |
| Парткод: | A02E 1048 00 |
| Деталь: | GUIDE |
| Парткод: | 4038 2187 04 |
| Деталь: | SHAFT |
| Парткод: | 4038 2192 02 |
| Деталь: | GEAR 27T |
| Парткод: | 4038 2189 01 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2190 03 |
| Деталь: | GEAR 16T |
| Парткод: | 4038 2191 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 2194 01 |
| Деталь: | SHAFT |
| Парткод: | 4038 2193 03 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038 2196 01 |
| Деталь: | GEAR 30T |
| Парткод: | 4038 2188 02 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4038 2184 01 |
| Деталь: | WASHER |
| Парткод: | 4038 2179 01 |
| Деталь: | CONTACT |
| Парткод: | 4038 2180 01 |
| Деталь: | SPRING |
| Парткод: | 4038 2042 01 |
| Деталь: | PIN |
| Парткод: | 1067 2501 01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A02E G100 00 |
| Деталь: | SKEW ADJUSTMENT ASSY |
| Парткод: | A02E R703 00 |
| Деталь: | Stepping motor |
| Парткод: | A02E M10C 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037 0906 01 |
| Деталь: | Caulking (Mounting Plate) |
| Парткод: | A02E G700 00 |
| Деталь: | Gear 22/22T |
| Парткод: | A02E 8117 00 |
| Деталь: | Timing Belt 264L |
| Парткод: | A02E 8113 00 |
| Деталь: | FLANGE |
| Парткод: | A02E 8119 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A02E 8121 00 |
| Деталь: | Gear 22/22/26T |
| Парткод: | A02E 8132 00 |
| Деталь: | Gear 22/23T |
| Парткод: | A02E 8118 01 |
| Деталь: | Timing Belt 316L |
| Парткод: | A02E 8114 00 |
| Деталь: | PULLEY |
| Парткод: | A02E 8120 01 |
| Деталь: | BUSHING |
| Парткод: | A02E 8152 00 |
| Деталь: | ROLLER |
| Парткод: | A02E 8106 00 |
| Деталь: | ROLL |
| Парткод: | 4497 3116 01 |
| Деталь: | BRACKET |
| Парткод: | A02E 5691 01 |
| Деталь: | Gear18T |
| Парткод: | A02E 5696 00 |
| Деталь: | Gear 26/34T |
| Парткод: | A02E 5693 01 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A02E R729 00 |
| Деталь: | SHAFT |
| Парткод: | 4030 3039 01 |
| Деталь: | LEVER |
| Парткод: | 4030 3078 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030 3017 03 |
| Деталь: | BRACKET |
| Парткод: | 4030 3014 01 |
| Деталь: | HOLDER |
| Парткод: | 4030 3013 01 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | A02E F566 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5636 00 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030 3125 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 5635 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5632 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 5610 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5631 00 |
| Деталь: | COVER |
| Парткод: | A02E 8104 00 |
| Деталь: | STOPPER |
| Парткод: | A02E 8110 00 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4066 3705 01 |
| Деталь: | HANDLE |
| Парткод: | A02E 8103 00 |
| Деталь: | Label Jam/Adu |
| Парткод: | A02E 9417 00 |
| Деталь: | PLATE SPRING |
| Парткод: | 4657 3736 01 |
| Деталь: | DOOR |
| Парткод: | A02E 8102 02 |
| Деталь: | PROTECTION |
| Парткод: | 1154 4670 01 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 9335 1300 61 |
| Деталь: | BRACKET |
| Парткод: | A02E 8108 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 8201 01 |
| Деталь: | ROLLER |
| Парткод: | A02E 8210 00 |
| Деталь: | MEMBER |
| Парткод: | A02E 8151 00 |
| Деталь: | ROLL |
| Парткод: | 4497 3116 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 8202 01 |
| Деталь: | BUSHING |
| Парткод: | A02E 8152 00 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 8205 00 |
| Деталь: | SCREW |
| Парткод: | 4163 5293 01 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4036 5765 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 8203 01 |
| Деталь: | SEAL |
| Парткод: | A02E 8207 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 8208 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 8204 02 |
| Деталь: | GUIDE |
| Парткод: | A02E 8206 01 |
| Деталь: | Gear 23T |
| Парткод: | A02E 8214 00 |
| Деталь: | Vertical Conveyance Assy |
| Парткод: | A02E R722 11 |
| Деталь: | REAR COVER |
| Парткод: | A02E 1625 00 |
| Деталь: | COVER |
| Парткод: | A02E 1627 00 |
| Деталь: | COVER |
| Парткод: | A02E 1626 00 |
| Деталь: | FILTER |
| Парткод: | A02E 1142 00 |
| Деталь: | CUSHION |
| Парткод: | A02E 1400 00 |
| Деталь: | Memory Wiring |
| Парткод: | A02E N118 00 |
| Деталь: | PWB assembly (PWB-EE1 ASSY) |
| Парткод: | A02E H002 01 |
| Деталь: | ImageProcessing Flatcable |
| Парткод: | A02E N10T 01 |
| Деталь: | GUIDE |
| Парткод: | A02E 1461 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 1401 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 1452 00 |
| Деталь: | PWB assembly(PWB-JMP ASSY) |
| Парткод: | A02E H343 00 |
| Деталь: | MEMORY MODULES |
| Парткод: | V865 3000 14 |
| Деталь: | PWB assembly (PWB-MFP ASSY) |
| Парткод: | A02E H341 06 |
| Деталь: | BRACKET |
| Парткод: | A02E 1453 00 |
| Деталь: | SCREW |
| Парткод: | A00J 1396 00 |
| Деталь: | SCREW |
| Парткод: | 4025 2283 01 |
| Деталь: | COVER |
| Парткод: | A02E 1490 00 |
| Деталь: | COVER |
| Парткод: | A02E 1491 00 |
| Деталь: | COVER |
| Парткод: | A02E 1492 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1465 01 |
| Деталь: | SPACER |
| Парткод: | V502 0100 36 |
| Деталь: | PWB Assembly (PWB-MC ASSY) |
| Парткод: | A02E H001 06 |
| Деталь: | SEAL |
| Парткод: | A02E 1497 00 |
| Деталь: | Scale |
| Парткод: | A02E 9409 01 |
| Деталь: | Scale |
| Парткод: | A02E 9408 00 |
| Деталь: | BRAKE |
| Парткод: | A02E 5934 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 5924 00 |
| Деталь: | BRAKE |
| Парткод: | A02E 5933 00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A02E 5923 00 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4687 3281 01 |
| Деталь: | FRICTION PLATE |
| Парткод: | A00J 6234 00 |
| Деталь: | BRAKE |
| Парткод: | A02E 5932 00 |
| Деталь: | LIFTING PLATE |
| Парткод: | A02E 5922 00 |
| Деталь: | GEAR 40T |
| Парткод: | A02E 5983 00 |
| Деталь: | Caulking Gear Mounting Plate |
| Парткод: | A02E G621 00 |
| Деталь: | GEAR 20T |
| Парткод: | A02E 5921 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 5981 00 |
| Деталь: | RESISTOR |
| Парткод: | V801 3000 06 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 5935 00 |
| Деталь: | EARTH GROUND |
| Парткод: | A02E 5936 00 |
| Деталь: | CUSHION |
| Парткод: | A02E 5919 00 |
| Деталь: | HOLDER |
| Парткод: | A02E 5905 01 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A02E 5925 00 |
| Деталь: | HOLD PLATE |
| Парткод: | A02E 5926 00 |
| Деталь: | GUIDE |
| Парткод: | A02E 5927 01 |
| Деталь: | CUSHION |
| Парткод: | A02E 5917 00 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A02E 5928 01 |
| Деталь: | Sensor Wiring /2 |
| Парткод: | A02E N103 00 |
| Деталь: | PLATE SPRING |
| Парткод: | A02E 5931 00 |
| Деталь: | SEAL |
| Парткод: | A02E 5937 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A02E M719 01 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A02E M720 01 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A02E M721 00 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A02E M722 00 |
| Деталь: | TRAY |
| Парткод: | A02E 1714 00 |
| Деталь: | TOP COVER |
| Парткод: | A02E 1715 00 |
| Деталь: | COVER |
| Парткод: | A02E 1716 00 |
| Деталь: | BRACKET |
| Парткод: | A02E 1615 00 |
| Деталь: | Label Remove/Clean |
| Парткод: | A02E 9425 00 |
| Деталь: | COVER |
| Парткод: | A02E 1489 01 |
| Деталь: | DUCT |
| Парткод: | A02E 1160 00 |
| Деталь: | SET PLATE |
| Парткод: | 1053 3103 01 |
| Деталь: | BAND |
| Парткод: | A02E 1612 00 |
| Деталь: | SCREW |
| Парткод: | 4038 1051 01 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475 2603 02 |
| Деталь: | BRACKET |
| Парткод: | 4038 1046 01 |
| Деталь: | COVER |
| Парткод: | A02E 1648 00 |
| Деталь: | Label magicolor 8650 |
| Парткод: | A02E 9431 00 |
| Деталь: | HINGE |
| Парткод: | A02E 1610 00 |
| Деталь: | SHAFT |
| Парткод: | A02E 1613 00 |
| Деталь: | FRONT COVER |
| Парткод: | A02E 1661 01 |
| Деталь: | Logo Mark |
| Парткод: | A00J 9455 00 |
| Деталь: | Label Waste Toner Remove |
| Парткод: | A02E 9426 00 |
| Деталь: | CLEANING PAD |
| Парткод: | 4038 2084 06 |
| Деталь: | CLANING MATERIAL |
| Парткод: | 4038 2083 02 |
| Деталь: | SEAL |
| Парткод: | A02E 1162 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1165 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1163 00 |
| Деталь: | SEAL |
| Парткод: | A02E 1164 00 |
| Деталь: | LEFT COVER |
| Парткод: | A02E 1650 01 |
| Деталь: | SEAL |
| Парткод: | A02E 1652 01 |
| Деталь: | LABEL |
| Парткод: | A02E 1653 00 |
| Деталь: | Ope.unit Cable /P |
| Парткод: | A02E N10W 01 Old |
| Деталь: | Ope.unit Cable /P |
| Парткод: | A02E N10W 02 |
| Деталь: | Label Consumables Reorder |
| Парткод: | A02E 9461 00 |
| Деталь: | Label Consumables Reorder |
| Парткод: | A02E 9462 00 |
| Деталь: | Label Consumables Reorder |
| Парткод: | A02E 9463 00 |
| Деталь: | Label Consumables Reorder |
| Парткод: | A02E 9464 00 |
| Деталь: | Label Consumables Reorder |
| Парткод: | A02E 9465 00 |
| Деталь: | Label Consumables Reorder |
| Парткод: | A02E 9466 00 |
| Деталь: | Label Emperon |
| Парткод: | A011 9462 00 |
Коды ошибок
C0001
C0202
C0204
C0206
C0208
C0209
C0210
C0211
C0212
C0213
C0214
C0215
C0301
C1004
C1180
C1181
C1182
C1183
C1190
C1191
C1192
C1193
C11A0
C11A1
C11A2
C11A3
C11A4
C11A5
C11A6
C11B0
C11B1
C11B2
C11B4
C11B5
C11B6
C11C0
C11C1
C11C2
C11C3
C11C5
C11D0
C11E0
C1301
C1401
C2151
C2152
C2164
C2253
C2254
C225D
C2351
C2451
C2551
C2552
C2553
C2554
C2555
C2556
C2557
C2558
C2559
C255A
C255B
C255C
C2650
C2651
C2652
C2653
C2654
C2A01
C2A02
C2A03
C2A04
C3101
C3201
C3202
C3301
C3302
C3421
C3423
C3461
C3721
C3723
C3821
C3823
C4151
C4152
C4153
C4154
C4551
C4552
C4553
C4554
C5102
C5103
C5351
C5353
C5354
C5357
C5371
CA051
CA052
CA053
CC151
CC153
CC155
CC163
CC164
CD002
CD004
CD005 ... CD030
CD201
Описание
| Error code: | C0001 |
| Description: | Main Motor turning at abnormal timing The Main Motor Lock signal remains faulty for a predetermined continuous period of time while the Main Motor remains stationary. |
| Remedy: | 1 Main Motor rotation while it is being energized: the voltage across PJ13I-7A on Master Board and GND remains DC 0 V. YES: Change Master Board. NO: Change motor. |
| Error code: | C0202 |
| Description: | Magenta PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 1 upper limit sensor (PS6) • Tray 1 lift-up motor (M6) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0204 |
| Description: | Yellow PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 2 upper limit sensor (PS14) • Tray 2 lift-up motor (M8) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0206 |
| Description: | Black PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 3 upper limit sensor (PS22) • Tray 3 lift-up motor (M23) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0208 |
| Description: | Tray 5 feeder up/down abnormality |
| Causes: | • Tray 4 upper limit sensor (PS27) • Tray 4 lift-up motor (M24) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Error code: | C0209 |
| Description: | LCT elevator motor malfunction |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0211 |
| Description: | Tray 1 feeder up/down abnormality • The paper feed tray 1 lift-up position sensor is not unblocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The paper feed tray 1 lift-up position sensor is not blocked even when the transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started. |
| Causes: | • Bypass lift-up motor (M26) • Bypass upper limit sensor (PS35) • Bypass lower limit sensor (PS36) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check the connector of M1 for proper drive coupling and correct as necessary. 3 PS17 I/O check PRCB CN6PRCB-7 (ON) D-2. 4 SL1 operation check PRCB CN6PRCB-4 (ON) D-1. 5 M1 operation check PRCB CN34PRCB-10 (REM) PRCB CN34PRCB-13 (LOCK) D-22. 6 Change SL1. 7 Change M1. 8 Change PRCB. |
| Error code: | C0212 |
| Description: | LCT ejection failure |
| Error code: | C0213 |
| Description: | LCT shift gate malfunction |
| Error code: | C0214 |
| Description: | LCT shifting failure |
| Causes: | • Shifter motor (M133) • Shifter stop / lower limit position sensor (PS138) • Shifter home sensor (PS139) • PC control board (PCCB) |
| Error code: | C0215 |
| Description: | LCT shift motor malfunction |
| Error code: | C0301 |
| Description: | Suction fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Suction fan (FM1) • Paper feed/transport drive board (PFTDB) |
| Remedy: | 1 Check the FM8 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM8 operation check PRCB CN3PRCB-2 (ON) PRCB CN3PRCB-3 (LOCK) D-4 to 5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C1004 |
| Description: | FNS communication error |
| Causes: | FS control board (FSCB) |
| Error code: | C1180 |
| Description: | Transport system drive malfunctions |
| Error code: | C1181 |
| Description: | Paddle motor malfunctions |
| Error code: | C1182 |
| Description: | Unsupported option trouble |
| Causes: | When JS-504 is installed: Shift motor (M2) Shift home sensor (PS6) JS control board (JSCB). When FS-527 is installed: Tray2 shift motor (M16) Tray2 shift home sensor (PS25) FS control board (FSCB) |
| Error code: | C1183 |
| Description: | Finishing option elevator drive malfunction |
| Causes: | Elevate motor (M15) Tray1 lower position sensor (PS21) Tray1 upper position sensor (PS24) Tray1 upper position switch (SW2) Tray1 lower position switch (SW3) FS control board (FSCB) |
| Error code: | C1190 |
| Description: | Finishing option aligning bar moving mechanism malfunction 1 |
| Causes: | Alignment plate motor (M13) Alignment plate home sensor (PS17) FS control board (FSCB) |
| Error code: | C1191 |
| Description: | Finishing option aligning bar moving mechanism malfunction 2 |
| Error code: | C1192 |
| Description: | Front aligning plate motor malfunctions |
| Error code: | C1193 |
| Description: | Rear aligning plate motor malfunctions |
| Error code: | C11A0 |
| Description: | Paper holding drive failure |
| Error code: | C11A1 |
| Description: | Finishing option exit roller pressure/retraction failure |
| Causes: | Exit roller retraction motor (M9) Exit roller pressure sensor (PS12) FS control board (FSCB) |
| Error code: | C11A2 |
| Description: | Saddle exit roller pressure/retraction failure |
| Causes: | <When FS-536 or FS-536SD is installed> • Receiving roller retraction motor (M4) • Receiving roller retraction sensor (PS11) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Receiving roller retraction motor (M10) • Receiving roller retraction sensor (PS22) • FS control board (FSCB) |
| Error code: | C11A3 |
| Description: | Shutter drive failure |
| Error code: | C11A4 |
| Description: | Saddle exit motor failure Booklet exit motor malfunctions |
| Error code: | C11A5 |
| Description: | Saddle in & out guide motor failure |
| Error code: | C11A6 |
| Description: | Saddle layable guide drive failure |
| Error code: | C11B0 |
| Description: | Finishing option stapler unit CD drive failure |
| Causes: | Stapler movement motor (M11) Stapler home sensor/1 (PS18) Stapler home sensor/2 (PS19) FS control board (FSCB) |
| Error code: | C11B1 |
| Description: | Stapler unit slide motor malfunctions |
| Error code: | C11B2 |
| Description: | Finishing option stapling mechanism malfunction 1 |
| Causes: | Stapler unit FS control board (FSCB) |
| Error code: | C11B4 |
| Description: | Stapler/folding motor malfunctions |
| Error code: | C11B5 |
| Description: | Side staple 1 drive failure |
| Causes: | Saddle stapler unit SD drive board (SDDB) FS control board (FSCB) |
| Error code: | C11B6 |
| Description: | Side staple 2 drive failure |
| Error code: | C11C0 |
| Description: | Punch motor malfunction |
| Causes: | Punch motor/1 (M100) Punch home sensor/1 (PS100) FS control board (FSCB) |
| Error code: | C11C1 |
| Description: | Punch control board malfunctions |
| Error code: | C11C2 |
| Description: | Punch side registration motor malfunctions |
| Error code: | C11C3 |
| Description: | Punch motor malfunctions |
| Error code: | C11C5 |
| Description: | Punch sensor malfunctions |
| Causes: | Paper size detect board (PSDTB) |
| Error code: | C11D0 |
| Description: | Crease motor drive failure |
| Error code: | C11E0 |
| Description: | Unsupported option trouble |
| Causes: | When FS-527 is installed: Duplex path switching motor (M2) Duplex path switching sensor (PS3)FS control board (FSCB). When JS-504 is installed: Route change motor (M3) Route change home sensor (PS4) JS control board (JSCB) |
| Error code: | C1301 |
| Description: | Finishing option cooling fan motor failure |
| Error code: | C1401 |
| Description: | Backup RAM failure |
| Error code: | C2151 |
| Description: | Secondary transfer roller pressure welding alienation • During a retraction operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its retracted position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. • During a pressure operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its pressed position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. |
| Causes: | • 2nd transfer pressure motor (M3) • 2nd transfer pressure sensor (PS50) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M11 connector for proper connection and correct as necessary. 2 Check the connector of M11 for proper drive coupling and correct as necessary. 3 PS36 I/O check PRCB CN3PRCB-9 (ON) D-5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C2152 |
| Description: | Transfer belt pressure welding alienation • During a retraction operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its retracted position within a predetermined period of time after the transfer belt retraction clutch is turned ON. • During a pressure operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its pressed position within a predetermined period of time after the transfer belt clutch is turned ON. |
| Causes: | • 1st transfer pressure sensor/K (PS51) • 1st transfer pressure sensor/YMC (PS52) • 1st transfer pressure motor (M21) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 PS31 I/O check PRCB CN36PRCB-15 (ON) D-26 to 27. 3 CL7 operation check PRCB CN39PRCB-10 (ON) D-23. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change CL7. 6 Change M5. 7 Change PRCB. |
| Error code: | C2164 |
| Description: | PC charge malfunction • When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined period of time. |
| Causes: | • Imaging unit • High voltage unit/1 (HV1) • Printer control board (PRCB) |
| Remedy: | 1 Check the imaging unit for proper connection and correct as necessary. 2 Check the HV connector for proper connection and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Change IU. 5 Change HV. 6 Change PRCB. |
| Error code: | C2253 |
| Description: | Color PC motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/YMC (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C2254 |
| Description: | Color PC motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/YMC motor (M16) • Printer control board (PRCB) |
| Remedy: | 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the M2 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M2 operation check PRCB CN35PRCB-4 (REM) PRCB CN35PRCB-7 (LOCK) D-22. 5 Change M2. 6 Change PRCB. |
| Error code: | C225D |
| Description: | Color dev. unit engagement/disengagement failure • The gears remain disengaged after the lapse of a predetermined period of time after the engagement operation is started by the color dev. unit engaged motor. • The gears remain engaged after the lapse of a predetermined period of time after the disengagement operation is started by the color dev. unit engaged motor. |
| Remedy: | 1 Check the M10 connector for proper connection and correct as necessary. 2 Check the M10 connector for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 PS26 I/O check PRCB CN39PRCB-18 (ON) D-24. 5 M10 operation check PRCB CN39PRCB-12 (REM) D-24. 6 Change M10. 7 Change PRCB. |
| Error code: | C2351 |
| Description: | Cleaning motor K error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective cleaning motor K. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC16 on the engine PWB and the connector of the cleaning motor K, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective cleaning motor K. Run maintenance item U030 and check if the cleaning motor K operates when YC16- B13 (remote signal) on the engine PWB goes low. If not, replace the cleaning motor K. Defective engine PWB. Run maintenance item U030 and check if YC16-B13 (remote signal) on the engine PWB goes low. If not, replace the engine PWB. |
| Error code: | C2451 |
| Description: | Release new transfer belt unit • A new installation is not detected when a new transfer cleaner unit (image transfer belt unit) is installed. |
| Remedy: | 1 Reinstall unit. 2 Check there is a short circuit in the fuse of the transfer belt unit. 3 Check the PRCB connector for proper connection and correct as necessary. 4 Change PRCB. |
| Error code: | C2551 |
| Description: | Abnormally low toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2552 |
| Description: | Abnormally high toner density detected cyan TCR sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2553 |
| Description: | Abnormally low toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2554 |
| Description: | Abnormally high toner density detected magenta TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2555 |
| Description: | Abnormally low toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Toner empty sensor/C (RS/C) • Toner empty sensor/M (RS/M) • Toner empty sensor/Y (RS/Y) • Toner supply motor/Y (M9) • Toner supply motor/M (M10) • Toner supply motor/C (M11) • Toner cartridge motor /YM (M13) • Toner cartridge motor /CK (M14) • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 M3, M4 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 (M3) PRCB CN39PRCB-5 to 8 (M4) D-23. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2556 |
| Description: | Abnormally high toner density detected yellow TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Toner cartridge /C • Toner cartridge /M • Toner cartridge /Y • Sub hopper unit • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit. 4 Change PRCB. |
| Error code: | C2557 |
| Description: | Abnormally low toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Developing unit • Toner cartridge • Toner empty sensor/K (PZS/K) • Toner supply motor/K (M12) • Toner cartridge motor/CK (M14) • MFP board (MFPB) |
| Remedy: | 1 M3 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 D-23. 2 Reinstall imaging unit. 3 Reinstall toner cartridge. 4 Change imaging unit /K. 5 Change PRCB. |
| Error code: | C2558 |
| Description: | Abnormally high toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Developing unit • Toner cartridge • Sub hopper unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit /K. 4 Change PRCB. |
| Error code: | C2559 |
| Description: | Cyan TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255A |
| Description: | Magenta TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255B |
| Description: | Yellow TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Reinstall imaging unit. 2 Change imaging unit. 3 Change PRCB. |
| Error code: | C255C |
| Description: | Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit /K. 2 Change imaging unit /K. 3 Change PRCB. |
| Error code: | C2650 |
| Description: | PF feed motor error (Side Multi Feeder) Object: Side multi feeder |
| Causes: | The ready signal is not at the L level (stable rotation) for passing 2s since the PF feed motor drive is started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected. The drive parts are faulty. Execute U247 [SMT] > [Motor On] to check the paper feeding operation. If the PF feed motor does not properly operate, reconnect the connector. Check if the PF feed roller and the drive gears rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. Executing U247 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF main PWB • PF main PWB - Engine PWB (Cable from the side multi feeder) Wiring diagram 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF drive unit (Side multi feeder) 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 5 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2651 |
| Description: | EEPROM access error (IU C) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2652 |
| Description: | EEPROM access error (IU M) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2653 |
| Description: | EEPROM access error (IU Y) |
| Causes: | • Imaging unit /C • Imaging unit /M • Imaging unit /Y • Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2654 |
| Description: | EEPROM access error (IU K) |
| Causes: | Imaging unit /C Imaging unit /M Imaging unit /Y Drum unit /K Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2A01 |
| Description: | EEPROM access error (TC C) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C2A02 |
| Description: | EEPROM access error (TC M) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C2A03 |
| Description: | EEPROM access error (TC Y) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C2A04 |
| Description: | EEPROM access error (TC K) |
| Remedy: | 1 Clean the connection between the toner cartridge and the machine if dirty. 2 Reinstall toner cartridge. 3 Check the harness for proper connection and correct as necessary. 4 Change toner cartridge. 5 Check that CN29 harness on PRCB has a ferrite core. If not, attach the ferrite core to the harness. 6 Change PRCB. |
| Error code: | C3101 |
| Description: | Fusing roller separation failure • With the fusing roller being retracted, the pulse of the fusing roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • With the fusing roller being pressed, the pulse of the roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • During a pressure operation of the fusing roller, the fusing roller is not at the pressed position even after the roller retraction sensor counts the specified number of pulses after the fusing retraction motor starts rotating. |
| Causes: | • Fusing pressure home sensor (PS55) • Fusing pressure motor (M29) • Printer control board (PRCB) • Fusing unit |
| Remedy: | 1 Check the M12 connector for proper connection and correct as necessary. 2 PS38 I/O check PRCB CN28PRCB-8 (ON) D-25. 3 M12 operation check PRCB CN28PRCB-4 to 5 D-25. 4 Change M12. 5 Change fusing unit. 6 Change PRCB. |
| Error code: | C3201 |
| Description: | Fusing motor failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3202 |
| Description: | Fusing motor turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3301 |
| Description: | Fusing cooling fan motor/ 1 failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Remedy: | 1 Check the FM9 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM9 operation check PRCB CN40PRCB-2 (ON) PRCB CN40PRCB-3 (LOCK) D-19. 4 Change FM9. 5 Change PRCB. |
| Error code: | C3302 |
| Description: | Fusing cooling fan motor/ 2,3 failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Paper cooling fan (FM8) • Printer control board (PRCB) |
| Remedy: | 1 Check the FM10 or FM11 connector for proper connection and correct as necessary 2 Check the fan for possible overload and correct as necessary. 3 FM10/FM11 operation check PRCB CN40PRCB-5 (ON) PRCB CN40PRCB-6 (LOCK) D-19. PRCB CN40PRCB-8 (ON) PRCB CN40PRCB-9 (LOCK) D-18. 4 Change FM10/FM11. 5 Change PRCB. |
| Error code: | C3421 |
| Description: | Fusing heaters trouble (heating side) • The temperature detected by the heating roller thermistor/C does not reach a predetermined level after the lapse of a predetermined period of time after the heating roller fusing heater lamp lights up. • The difference between the maximum and minimum temperatures detected by the heating roller thermistor/C within a predetermined period of time after the start of a warm-up cycle is below or above a predetermined value. • The temperature detected after a pressure level correction remains under a predetermined level even after the lapse of a predetermined period of time after the start of the temperature detection. • During a warm-up, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. |
| Causes: | • Fusing unit • C3421: Fusing temperature sensor/1 (TEM1: center) • C3426: Fusing temperature sensor/1 (TEM1: edge) • DC power supply (DCPS) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3423 |
| Description: | Fusing heaters trouble (pressurizing side) • After warm-up operation starts, the fusing pressure roller thermistor does not detect a temperature as high as a predetermined one though a predetermined period of time has elapsed. • The temperature of the pressure roller remains lower than a predetermined level even after the lapse of a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3461 |
| Description: | Release new fusing unit • A new installation is not detected when a new fusing Unit is installed. |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 3 Reinstall fusing unit. 4 Change fusing unit. 5 Change PRCB. |
| Error code: | C3721 |
| Description: | Fusing abnormally high temperature detection (heating side) • The heating roller thermistor continues to detect a temperature higher than a predetermined one for a predetermined period of time. • Hard protection signal L is detected continuously over a predetermined period of time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3723 |
| Description: | Fusing abnormally high temperature detection (pressurizing side) • The temperature of the pressure roller continues to be higher than a predetermined level for a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • Pressure roller power supply unit (PRPU) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3821 |
| Description: | Fusing abnormally low temperature detection (heating side) • The heating roller thermistor continues to detect a temperature lower than a predetermined one for a predetermined period of time. • In the states other than a warm-up operation, a zero cross signal cannot be detected after the lapse of a predetermined period of time after the fusing heater is turned ON or OFF. • The power supply frequency cannot be detected. |
| Causes: | • Fusing unit • C3821: Thermistor/1 (TH1) • C3822: Thermistor/2 (TH2) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3823 |
| Description: | Fusing abnormally low temperature detection (pressurizing side) • The temperature of the pressure roller continues to be lower than a predetermined level for a predetermined period of time after a temperature correction. |
| Causes: | • Fusing unit • Pressure roller thermistor/2 (TH3) • IH power supply unit (IHPU) • Noise filter (NF1) • Pressure roller power supply unit (PRPU) • MFP board (MFPB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C4151 |
| Description: | Polygon motor rotation trouble (C) • The polygon motor fails to turn stably even after the lapse of a given period of time after activating the polygon motor. • Motor lock signal detects HIGH for a given period time consecutively during the polygon motor is rotating. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4152 |
| Description: | Polygon motor rotation trouble (M) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4153 |
| Description: | Polygon motor rotation trouble (Y) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4154 |
| Description: | Polygon motor rotation trouble (K) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4551 |
| Description: | Laser malfunction (C) • SOS signal is not detected even after the lapse of a given period of time after staring the laser output. • SOS signal is not detected for a given period of time during printing or image stabilization adjustment. |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4552 |
| Description: | Laser malfunction (M) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4553 |
| Description: | Laser malfunction (Y) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C4554 |
| Description: | Laser malfunction (K) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PHREYB. 4 Change PRCB. |
| Error code: | C5102 |
| Description: | Main high-voltage error C |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5103 |
| Description: | Main high-voltage error M |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5351 |
| Description: | Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • DC power supply cooling fan (FM9) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1 Check the FM5 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check PRCB CN30PRCB-11 (ON) PRCB CN30PRCB-12 (LOCK) K-8. 4 Change FM5. 5 Change DCPU. 6 Change PRCB. |
| Error code: | C5353 |
| Description: | Cooling fan motor/2’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Cooling fan motor/2 (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM2 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM2 operation check PRCB CN28PRCB-2 (ON) PRCB CN28PRCB-3 (LOCK) D-24. 4 Change FM2. 5 Change PRCB. |
| Error code: | C5354 |
| Description: | Exhaust fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Ozone ventilation fan (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM4 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM4 operation check PRCB CN3PRCB-14 (ON) PRCB CN3PRCB-16 (LOCK) D-6. 4 Change FM4. 5 Change PRCB. |
| Error code: | C5357 |
| Description: | Cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Machine cooling fan (FM1) • CPU board (CPUB) • Base board (BASEB) |
| Remedy: | 1 Check the FM1 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM1 operation check PRCB CN30PRCB-4 (ON) PRCB CN30PRCB-6 (LOCK) K-7. 4 Change FM1. 5 Change PRCB. |
| Error code: | C5371 |
| Description: | MFP board cooling fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Remedy: | 1 Check the FM6 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM6 operation check PRCB CN44PRCB-1 (REM) PRCB CN44PRCB-3 (LOCK) K-9. 4 Change FM6. 5 Change MFPB. |
| Error code: | CA051 |
| Description: | Standard controller configuration failure • The controller of the printer control board (PRCB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA052 |
| Description: | Controller hardware error • A controller hardware error is detected in the network I/F. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA053 |
| Description: | Controller start failure • A controller start failure is detected in the controller interface. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CC151 |
| Description: | ROM contents error upon startup (MSC) • A fault is detected in a sequence of ROM contents check of the MSC (PRCB) during starting |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. |
| Error code: | CC153 |
| Description: | ROM contents error upon startup (PRT) • A fault is detected in a sequence of ROM contents check of the mechanical control board (MFPB) during starting. |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. |
| Error code: | CC155 |
| Description: | Finisher ROM error |
| Causes: | FS control board (FSCB) |
| Error code: | CC163 |
| Description: | ROM contents error (PRT) • The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Rewrite the firmware. 2 Change PRCB 2.1. Turn OFF the power switch and replace the current PRCB with a new one. (When using a PRCB of another machine in service, be sure to use a PRCB installed in the same model.) 2.2. Update the PRCB firmware. 2.3. After completing the firmware update, turn OFF and ON the power switch and check to see that warm-up is started. 2.4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SV ERB. 3 Change SV ERB 3.1. Replace the current SV ERB with a new one. 3.2. Turn ON the power switch and check to see that warm-up is started. (One minute is spent to prepare the new SV ERB for use. During the period, the control panel backlight stays off.) 3.3. Make the specified readjustments. 4 If the above actions do not solve the problem, contact KMBT. |
| Error code: | CC164 |
| Description: | ROM contents error (MSC) • The wrong model of firmware is detected in the MFP board when the power switch is turned ON. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the corresponding board. 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CD002 |
| Description: | JOB RAM save error • The error in save of JOB data to the memory/ hard disk and its read error are detected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB. |
| Error code: | CD004 |
| Description: | Hard disk access error • Unable to communicate between the hard disk and printer control board (PRCB). |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | Check the hard disk connector for proper connection and correct as necessary. 2 Reinstall the hard disk. 3 Change hard disk. 4 Change MFPB. |
| Error code: | CD005 ... CD030 |
| Description: | Hard disk error |
| Remedy: | Check the hard disk connector for proper connection and correct as necessary. 2 Reinstall the hard disk. 3 Change hard disk. 4 Change MFPB. |
| Error code: | CD201 |
| Description: | Memory error |
| Causes: | • MFP board (MFPB) • Memory |
| Remedy: | Check to see if the memory on MFPB is installed correctly. 2 Change the memory on MFPB. 3 Change MFPB. |
Название
Konica Minolta Блок проявки черный
Konica Minolta Блок проявки желтый
Konica Minolta Блок проявки пурпурный
Konica Minolta Блок проявки голубой
Konica Minolta Емкость отработанного тонера
Konica Minolta Блок ленты переноса изображения
Konica Minolta Тонер-картридж черный
Konica Minolta Тонер-картридж желтый
Konica Minolta Тонер-картридж пурпурный
Konica Minolta Тонер-картридж голубой
