Kyocera FS-C1020 MFP

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Число страниц в месяц

10000

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Цветность печати	цветная
Размещение	настольный
Число страниц в месяц	10 000
Тип	лазерный/светодиодный
Технология печати	лазерная
Макс. формат	A4
Область применения	малый офис
Печать фотографий
Телефон
Тип устройства	МФУ
Копир
Сканер
Факс
Принтер
Система непрерывной подачи чернил
Печать без полей
Пигментные чернила
Количество цветов	4
Двусторонняя печать
Прямая печать
Время разогрева	30
Макс, разрешение для ч/б печати
По X	1 200
По Y	600
По X	2 400
Скорость ч/б печати
A4	20
Время выхода первого отпечатка
Ч/б	14
Копир
Макс, количество копий за цикл	99
Шаг масштабирования	0,01
Время выхода первой копии	30
Значение масштаба
Максимальное	4
Минимальное	0,25
Макс, разрешение (ч/б)
По Y	1 200
По Y	600
По X	600
Сканер
Слайд-адаптер
Отправка изображения по e-mail
Стандарт WIA
Стандарт TWAIN
Тип сканера	планшетный/протяжный
Емкость устройства автоподачи оригиналов	35
Макс. формат оригинала	A4
Разрешение сканера
По Х	1 200
Скорость сканирования
Цветн,	6
Ч/б	12
Расходные материалы
Ресурс ч/б картриджа/тонера	6 500
Количество картриджей	4
Ресурс цветного картриджа/тонера	6 000
Печать на:
CD/DVD
Фотобумаге
Рулоне
Матовой бумаге
Этикетках
Глянцевой бумаге
Пленках
Конвертах
Карточках
Плотность бумаги
Максимальная	160
Минимальная	60
Факс
Цветной
Макс, скорость передачи данных	33,6 Кбит/с
PC Fax
Телефон
Беспроводная трубка
Спикерфон
Автоответчик
Caller ID
Стандарт DECT
АОН
Проводная трубка
Языки управления
PCL 5c
PostScript 3
PCL 6
PostScript
PDF
PostScript 2
PCL 5e
PPDS
Лотки
Емкость лотка ручной подачи	1
Подача бумаги
Максимальная	751
Стандартная	251
Вывод бумаги
Стандартный	150
Финишер
Сортировка со сдвигом
Степлер
Электронная сортировка
Брошюровщик
Сортер
Интерфейсы
Ethernet (RJ-45)
USB
Устройство для чтения карт памяти
Инфракрасный порт
RS-232
Веб-интерфейс
Bluetooth
Wi-Fi 802.11n
Wi-Fi
FireWire (IEEE 1394)
LPT
AirPrint
Версия USB	2,0
Память/Процессор
Объем памяти	256
Частота процессора	400
Процессор	ARM11
Дополнительная информация
Работа от аккумулятора
Экран
Поддержка ОС
DOS
Linux
Windows
Mac OS
Потребляемая мощность
При работе	382
В режиме ожидания	10
Уровень шума
При работе	57
В режиме ожидания	34
Габариты
Высота	476
Глубина	493
Ширина	420
Вес	30

Коды ошибок

195

202

203

204

220

222

240

300

396

397

445

480

490

500

530

531

541

542

543

545

547

548

557

559

669

690

819

823

824

827

828

Описание

Парткод

Название

Kyocera Блок фотобарабана

Kyocera Блок проявки

Kyocera Узел термозакрепления

Kyocera Тонер-картридж голубой

Kyocera Тонер-картридж черный

Kyocera Тонер-картридж пурпурный

Kyocera Тонер-картридж желтый

Kyocera Сборник отработанного тонера

Kyocera Узел термозакрепления 230v

Kyocera Сервисный комплект

Kyocera Тонер-картридж черный

Kyocera Бункер отработанного тонера

Error code:	195
Description:	Serial Number Error
Causes:	The serial number stored in the memory (EGB) is not correct.
Remedy:	EEPROM defective EGB replaced without original EEPROM

Error code:	202
Display:	ERROR 202 PARAMETER
Description:	Polygon motor error 1: ON timeout
Causes:	The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed.

Error code:	203
Display:	Power OFF/ON 203:Error ssssssssssssssss
Description:	Polygon motor error 2: OFF timeout
Causes:	The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off.

Error code:	204
Display:	Power OFF/ON 204:Error
Description:	Polygon motor error 3: XSCRDY signal error
Causes:	The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing.
Remedy:	• Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board).

Error code:	220
Display:	Service Call 220: Error
Description:	Laser Synchronizing Detection Error: [K]/[Y]
Causes:	The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally.

Error code:	222
Description:	Laser Synchronizing Detection Error: [M]/[C]
Causes:	The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally.
Remedy:	• Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB 1. Check the connectors. 2. Replace the laser optics unit. 3. Replace the EGB.·

Error code:	240
Display:	Service call 240: Error
Description:	LD error
Causes:	The IPU (EGB) detects a problem at the LD unit.
Remedy:	• Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit.

Error code:	300
Description:	High voltage power output error
Causes:	The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit).
Remedy:	• Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB.

Error code:	396
Description:	Black drum motor error
Causes:	The LOCK signal error is detected when the EGB monitors the black drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.)
Remedy:	• Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the black drum motor. Replace it if necessary.e hig

Error code:	397
Description:	Color drum motor error
Causes:	The LOCK signal error is detected when the EGB monitors the color drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.)
Remedy:	• Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the color drum motor. Replace it if necessary.

Error code:	445
Description:	ITB (Image Transfer Belt) Unit: Home Position Error
Causes:	The ITB contact sensor does not detect the home position of the ITB for 5 seconds after the ITB unit initialization has been done. ITB (Image Transfer Belt) Unit: Contact Position Error The ITB contact sensor does not detect the contact position of the ITB for 5 seconds after the ITB unit has moved to the contact position. ITB (Image Transfer Belt) Unit: No-contact Position Error The ITB contact sensor does not detect the home position of the ITB for 5 seconds after the ITB unit has moved to no-contact position.
Remedy:	• Defective ITB contact motor • Defective ITB contact sensor • Defective ITB unit 1. Replace the ITB contact motor. 2. Replace the ITB contact sensor. 3. Replace the ITB unit.

Error code:	480
Display:	Remove paper 480: Stacker full
Description:	Agitator Motor Error
Causes:	The agitator motor error is detected twice for 10 msec during the initialization at power-on or after the cover is closed.
Remedy:	• Disconnected or defective harness • Defective agitator motor 1. Check or replace the harness. 2. Replace the agitator motor.

Error code:	490
Display:	Set 490: No paper in MP tray (* stands for A4 B4, etc.)
Description:	ITB (Image Transfer Belt) Unit Set Error
Causes:	The TM sensor does not detect the reflection from the ITB.
Remedy:	• No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S

Error code:	500
Description:	Transport/Fusing Motor Error
Causes:	The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.)
Remedy:	• Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary.

Error code:	530
Description:	LSU Fan Motor Error
Causes:	A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued.
Remedy:	• Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor.

Error code:	547
Description:	Zero Cross Error
Causes:	The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door.
Remedy:	• Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure.

Error code:	559
Description:	Consecutive Fusing Jam
Causes:	The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF").
Remedy:	• Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.

Error code:	531
Description:	Fusing Fan Motor Error
Causes:	A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued.
Remedy:	• Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor.

Error code:	541
Description:	Thermistor Error
Causes:	The thermistor output is less than 0°C for 7 seconds.
Remedy:	• Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.

Error code:	542
Description:	Print Ready Temperature Error
Causes:	• The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on.
Remedy:	• Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.

Error code:	543
Description:	High Temperature Detection Error
Causes:	This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne
Remedy:	• Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.

Error code:	545
Description:	Heating Lamp Full-Power Error
Causes:	The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating.
Remedy:	• Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.

Error code:	548
Description:	Low Temperature Error
Causes:	The center thermistor detects 100°C or less for 4 seconds.
Remedy:	• Defective fusing lamp • Defective thermistor 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.d

Error code:	557
Description:	Zero Cross Frequency Error
Causes:	The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds.
Remedy:	• Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure.

Error code:	669
Description:	EEPROM Error
Causes:	An unexpected value exists in the initialization flag of the EEPROM
Remedy:	• EEPROM not initialized • Defective EEPROM

Error code:	690
Description:	GAVD Communication Error
Causes:	The ID of the GAVD is not identified during initialization. The chip ID of the GAVD cannot be detected by the machine at power-on.
Remedy:	• Defective EGB 1. Replace the EGB. EE

Error code:	819
Display:	SYSTEM HALT (*) 819 : FW/HROM SIZ
Description:	Service Cycle Power
Causes:	• Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board.
Remedy:	• Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan