Kyocera KM-3040
Рейтинг
Модули
Scanner Section 1
Paper Feed Section 4
Options 1
Drive Section 1
DRIVE SECTION 2
Electrical Components 1
PAPER FEED
DUPLEX
Paper Feed Section 1
ADF 1
Paper Conveying Section 1
PAPER FEED SECTION 2
DEVELOPING SECTION
FRAMES
SCANNER SECTION 2
Duplex Section
FRAME L
Paper Feed Section 3
Exit Section 2
Options 2
ELECTRICAL COMPONENTS 2
COVERS
Paper Conveying Section 2
COOLING SECTION
Paper Cassettes
Fuser Section
Operation Section
Exit Section 1
Image Formation Section
Детали COOLING SECTION
| Деталь: | CUSHION,CONTACT GLASS |
| Парткод: | 29812291 |
| Деталь: | MIRROR B |
| Парткод: | 2AV12160 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | SPRING,MIRROR HOLDER |
| Парткод: | 2BC12190 |
| Деталь: | LABEL GLASS CAUTION |
| Парткод: | 2C905160 |
| Деталь: | RETAINER WIRE |
| Парткод: | 2C912150 |
| Деталь: | WIRE DP |
| Парткод: | 302H046330 |
| Деталь: | MOUNT PI |
| Парткод: | 2C912220 |
| Деталь: | GROUND ISU COVER |
| Парткод: | 302H017360 |
| Деталь: | GEAR Z18/39 |
| Парткод: | 2C912310 |
| Деталь: | Gear Z36 |
| Парткод: | 2C912320 |
| Деталь: | DRUM PULLEY |
| Парткод: | 2C912340 |
| Деталь: | WIRE SCANNER BLACK |
| Парткод: | 2C912350 |
| Деталь: | WIRE SCANNER GRAY |
| Парткод: | 2C912360 |
| Деталь: | GROUND FFC |
| Парткод: | 302H017370 |
| Деталь: | PT.SENSOR GP1A73AJ00/ BK |
| Парткод: | 5FNXGP1A73A++02 |
| Деталь: | HOLDER CCD WIRE |
| Парткод: | 302H017330 |
| Деталь: | FFC CCD |
| Парткод: | 302JB46110 |
| Деталь: | MOUNT RELEASE SWITCH |
| Парткод: | 2C912610 |
| Деталь: | GUIDE RELEASE SWITCH |
| Парткод: | 2C912620 |
| Деталь: | SHAFT RELEASE SWITCH |
| Парткод: | 2C912640 |
| Цена: | 80 ₽ |
| Деталь: | SPRING RELEASE SWITCH |
| Парткод: | 2C912650 |
| Деталь: | SHIELD SCANNER FRAME |
| Парткод: | 2C912670 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | SHIELD SCANNER FRAME B |
| Парткод: | 2C912710 |
| Деталь: | SLIDER SCANNER |
| Парткод: | 2DC12230 |
| Деталь: | WIRE SCANNER PI |
| Парткод: | 302H046170 |
| Деталь: | ADJUSTING PLATE B |
| Парткод: | 302C912131 |
| Деталь: | SPRING SCANNER TENSION |
| Парткод: | 302C912291 |
| Деталь: | MOTOR PLATE SCANNER |
| Парткод: | 302C912302 |
| Деталь: | BEARING MF128ZZ |
| Парткод: | 302FB11160 |
| Деталь: | SENSOR ORIGINAL |
| Парткод: | 302H044110 |
| Деталь: | FILM LAMP |
| Парткод: | 302GR17400 |
| Деталь: | PULLEY SCANNER |
| Парткод: | 302GR17820 |
| Деталь: | SCANNER FRAME ASSY |
| Парткод: | 302H000010 |
| Деталь: | MIRROR FRAME A |
| Парткод: | 302H017050 |
| Деталь: | MIRROR FRAME B |
| Парткод: | 302H017060 |
| Деталь: | GUIDE LAMP WIRE A |
| Парткод: | 302H017070 |
| Деталь: | GUIDE LAMP WIRE B |
| Парткод: | 302H017080 |
| Деталь: | GUIDE LAMP WIRE C |
| Парткод: | 302H017090 |
| Деталь: | REFLECTOR SCANNER |
| Парткод: | 302H017100 |
| Деталь: | PARTS LAMP SCANNER W SP |
| Парткод: | 302H094130 |
| Деталь: | PULLEY LEFT FRAME |
| Парткод: | 302H017120 |
| Деталь: | MOUNT PULLEY |
| Парткод: | 302H017130 |
| Деталь: | MOUNT INVERTER |
| Парткод: | 302H017140 |
| Деталь: | MIRROR A |
| Парткод: | 302H017150 |
| Деталь: | EDGING, EDS-0607L(KITAGAWA) |
| Парткод: | M2104390 |
| Деталь: | MOUNT DF |
| Парткод: | 302H017170 |
| Деталь: | PULLEY SCANNER |
| Парткод: | 302H017180 |
| Деталь: | SHAFT DRIVE |
| Парткод: | 302H017190 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | GUIDE CCD WIRE |
| Парткод: | 302H017210 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | LID GUIDE WIRE C |
| Парткод: | 302H017230 |
| Деталь: | TAPE REFLECTOR |
| Парткод: | 302H017250 |
| Деталь: | BELT SCANNER |
| Парткод: | 302H017260 |
| Деталь: | SPRING SCANNER A |
| Парткод: | 302H017290 |
| Деталь: | SPRING SCANNER B |
| Парткод: | 302H017300 |
| Деталь: | GROUND SCANNER REAR |
| Парткод: | 302H017310 |
| Деталь: | GROUND SCANNER FRONT |
| Парткод: | 302H017320 |
| Деталь: | COVER ISU |
| Парткод: | 302H017600 |
| Деталь: | PARTS MOTOR SCANNER SP |
| Парткод: | 302H094440 |
| Деталь: | PARTS,LAMP INVERTER,SP |
| Парткод: | 302H094280 |
| Деталь: | PARTS ISU |
| Парткод: | 302H093070 |
| Деталь: | ACTUATOR BYPASSFEED |
| Парткод: | 2BL06730 |
| Деталь: | DIAL BYPASSFEED |
| Парткод: | 2BL06830 |
| Деталь: | SPACER RIGHT GUIDE |
| Парткод: | 302C907660 |
| Деталь: | LABEL JAM A1 |
| Парткод: | 302GR34050 |
| Деталь: | LABEL JAM A2 |
| Парткод: | 302GR34060 |
| Деталь: | LABEL JAM A3 |
| Парткод: | 302GR34070 |
| Деталь: | GUIDE MPF FEED |
| Парткод: | 302H008010 |
| Деталь: | BASE MPF FEED |
| Парткод: | 302H008020 |
| Деталь: | GROUND PLATE MPF |
| Парткод: | 302H008050 |
| Деталь: | RAIL MPF FEED |
| Парткод: | 302H008080 |
| Деталь: | SPRING BYPASSFFED |
| Парткод: | 302H008140 |
| Деталь: | COLLER MPF |
| Парткод: | 302H008170 |
| Деталь: | CUT WASHER MPF 5 |
| Парткод: | 302H008180 |
| Деталь: | SHAFT MPF FEED SIDE |
| Парткод: | 302H008200 |
| Деталь: | PULLEY 15 MPF FEED |
| Парткод: | 302H008220 |
| Деталь: | SPRING BYPASS |
| Парткод: | 302H008240 |
| Деталь: | PULLEY MPF Z25 |
| Парткод: | 302H008250 |
| Деталь: | GEAR MPF Z30 |
| Парткод: | 302H008260 |
| Деталь: | SPRING BYPASSFEED 2 |
| Парткод: | 302H008280 |
| Деталь: | STAY MPF |
| Парткод: | 302H008320 |
| Деталь: | STAY GUIDE MPF UPPER |
| Парткод: | 302H008420 |
| Деталь: | BUSH 8 EW |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | PARTS ROLLER MPF FEED A SP |
| Парткод: | 302H094110 |
| Деталь: | PARTS ROLLER MPF FEED B SP |
| Парткод: | 302H094120 |
| Деталь: | BELT S2M 230 |
| Парткод: | 303J131270 |
| Деталь: | RING STOPPER 6 |
| Парткод: | 5MVL177DN002 |
| Деталь: | PULLEY RAIL MPF FEED |
| Парткод: | 302H008090 |
| Деталь: | WIRE MPF PI |
| Парткод: | 302H046450 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | PARTS MPF FEED UNIT |
| Парткод: | 302H093120 |
| Деталь: | COVER,PLATEN |
| Парткод: | 2A612800 |
| Деталь: | MAT,ORIGINAL HOLDER |
| Парткод: | 2A612810 |
| Деталь: | HINGE,ORIGINAL HOLDER |
| Парткод: | 2A612820 |
| Деталь: | STOPPER RELEASE SWITCH |
| Парткод: | 2C912630 |
| Деталь: | ORIGINAL POCKET |
| Парткод: | 60904280 |
| Деталь: | SET,PLATEN COVER TYPE D |
| Парткод: | 2CX82010 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 2C904550 |
| Деталь: | GEAR 26 DEV |
| Парткод: | 2C922150 |
| Деталь: | GEAR 29 FIX JOINT |
| Парткод: | 2C922230 |
| Деталь: | BEARING 6-15-17 |
| Парткод: | 2FT22160 |
| Деталь: | SPACER COUPLING |
| Парткод: | 302FT22200 |
| Деталь: | COUPLING DRUM 2 |
| Парткод: | 302FT22250 |
| Деталь: | BASE MAIN DRIVE |
| Парткод: | 302H031010 |
| Деталь: | MOUNT DRIVE DRUM |
| Парткод: | 302H031021 |
| Деталь: | GEAR Z90H-Z36H |
| Парткод: | 302H031090 |
| Деталь: | GEAR Z40H-Z27H |
| Парткод: | 302H031110 |
| Деталь: | GEAR Z30H |
| Парткод: | 302H031130 |
| Деталь: | GEAR Z152H |
| Парткод: | 302H031140 |
| Цена: | 410 ₽ |
| Деталь: | GEAR Z50S |
| Парткод: | 302H031160 |
| Цена: | 80 ₽ |
| Деталь: | GEAR Z25H DEV |
| Парткод: | 302H031170 |
| Деталь: | GEAR Z89H-Z24S |
| Парткод: | 302H031180 |
| Деталь: | GEAR Z25H |
| Парткод: | 302H031190 |
| Деталь: | GEAR Z43S |
| Парткод: | 302H031230 |
| Деталь: | GEAR Z55H-Z30S |
| Парткод: | 302H031240 |
| Деталь: | POSITIONING BUSH DRUM |
| Парткод: | 302H031320 |
| Цена: | 70 ₽ |
| Деталь: | SPRING DRUM COUPLING |
| Парткод: | 302H031330 |
| Деталь: | SHAFT COUPLING |
| Парткод: | 302H031340 |
| Деталь: | GUIDE SHAFT DEV |
| Парткод: | 302H031370 |
| Деталь: | SPRING FUSER JOINT |
| Парткод: | 302H031410 |
| Деталь: | BEARING 6900ZZNR |
| Парткод: | G3169000 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610005++H01 |
| Деталь: | PLATE FEED DRIVE |
| Парткод: | 302H006130 |
| Деталь: | COLLAR BELT |
| Парткод: | 2BL22580 |
| Деталь: | GEAR Z41S-P30 FEED |
| Парткод: | 302H006320 |
| Деталь: | BELT DRIVE FEED |
| Парткод: | 2BL22350 |
| Деталь: | GEAR Z25S FEED CLUTCH |
| Парткод: | 302H006230 |
| Деталь: | GEAR Z22S FEED |
| Парткод: | 302H006150 |
| Деталь: | GEAR Z21S-Z28S FEED |
| Парткод: | 302H006160 |
| Деталь: | GEAR Z34S-Z23S FEED |
| Парткод: | 302H006170 |
| Деталь: | GEAR Z60S-Z35S FEED |
| Парткод: | 302H006310 |
| Деталь: | PLATE MPF DRIVE A |
| Парткод: | 302H006260 |
| Деталь: | GEAR Z60S FEED |
| Парткод: | 302H006250 |
| Цена: | 80 ₽ |
| Деталь: | GEAR Z41S FEED |
| Парткод: | 302H006270 |
| Цена: | 70 ₽ |
| Деталь: | GEAR Z40S-Z32S |
| Парткод: | 2BL22550 |
| Цена: | 550 ₽ |
| Деталь: | PLATE MPF DRIVE B |
| Парткод: | 302H006280 |
| Деталь: | PARTS MOTOR MAIN SP |
| Парткод: | 302H094200 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | HOLDER MOTOR |
| Парткод: | 302H031360 |
| Деталь: | WIRE SADDLE,HL-28 |
| Парткод: | M2109150 |
| Деталь: | SHIELD SCREW |
| Парткод: | 302H002380 |
| Деталь: | PARTS DR-670 |
| Парткод: | 302H093150 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | MOUNT FEED DRIVE |
| Парткод: | 302H031030 |
| Деталь: | BASE FEED DRIVE |
| Парткод: | 302H031041 |
| Деталь: | GEAR Z24H-Z35S FEED |
| Парткод: | 302H031050 |
| Деталь: | GEAR Z23H FEED B |
| Парткод: | 302H031060 |
| Деталь: | GEAR Z60H-Z30H FEED |
| Парткод: | 302H031080 |
| Деталь: | GEAR Z95H-Z41S FEED |
| Парткод: | 302H031100 |
| Деталь: | GEAR Z35S DU |
| Парткод: | 302H031120 |
| Деталь: | GEAR Z41S FEED MAIN |
| Парткод: | 302H031150 |
| Деталь: | SHAFT FEED |
| Парткод: | 302H031200 |
| Деталь: | GEAR Z22H-Z24S FEED |
| Парткод: | 302H031210 |
| Деталь: | SHAFT DU |
| Парткод: | 302H031220 |
| Деталь: | GEAR Z30S FEED |
| Парткод: | 302H031250 |
| Деталь: | GEAR Z23H FEED |
| Парткод: | 302H031270 |
| Деталь: | GEAR Z30S DPX |
| Парткод: | 302H031280 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CUT WASHER 6 |
| Парткод: | 2BL21510 |
| Деталь: | GEAR 60 |
| Парткод: | 2C922080 |
| Деталь: | COUPLING CONT P |
| Парткод: | 2C922170 |
| Деталь: | SPRING CONT P |
| Парткод: | 2C922260 |
| Деталь: | BUSH 8 EW |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | GEAR Z33S CONT |
| Парткод: | 302H031260 |
| Деталь: | BASE CONT DRIVE |
| Парткод: | 302H031290 |
| Деталь: | MOUNT CONT DRIVE |
| Парткод: | 302H031300 |
| Деталь: | SHAFT CONT |
| Парткод: | 302H031350 |
| Деталь: | GEAR Z33S CONT C |
| Парткод: | 302H031380 |
| Деталь: | GEAR Z33S CONT D |
| Парткод: | 302H031390 |
| Деталь: | TORQUE LIMITER 4000 |
| Парткод: | 302H031400 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000001+H01 |
| Деталь: | GEAR Z26S DU |
| Парткод: | 302H031310 |
| Деталь: | HOLDER MOTOR |
| Парткод: | 302H031360 |
| Деталь: | PARTS MOTOR MAIN SP |
| Парткод: | 302H094200 |
| Деталь: | PARTS CLUTCH REGISTRATION SP |
| Парткод: | 302H094220 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | COVER DRIVE MID FEED |
| Парткод: | 302H024410 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PIN SCREW BIND 3X6S |
| Парткод: | 303KZ02180 |
| Деталь: | PARTS FEED DRIVE UNIT |
| Парткод: | 302H093160 |
| Деталь: | PARTS CONT DRIVE ASSY |
| Парткод: | 302H093170 |
| Деталь: | SHIELD SCREW |
| Парткод: | 302H002380 |
| Деталь: | FILM SHIELD FFC |
| Парткод: | 302JC39130 |
| Деталь: | LID VENDOR |
| Парткод: | 302FB26290 |
| Деталь: | FAN CONTROLLER 80-15 |
| Парткод: | 302GR44050 |
| Деталь: | SHIELD MAIN PWB C |
| Парткод: | 302JC39020 |
| Деталь: | PARTS,PWB INTERFACE ASSY SP |
| Парткод: | 302JB94060 |
| Деталь: | MOUNT PRINT CONNECTOR |
| Парткод: | 302JC39060 |
| Деталь: | WIRE PANEL MAIN |
| Парткод: | 302JB46011 |
| Деталь: | BASE TERMINAL MAIN |
| Парткод: | 302H039060 |
| Деталь: | BASE TERMINAL TRANSFER |
| Парткод: | 302H039070 |
| Деталь: | TERMINAL MAIN |
| Парткод: | 302H039080 |
| Деталь: | TERMINAL TRANSFER |
| Парткод: | 302H039090 |
| Деталь: | TERMINAL SEPARATION |
| Парткод: | 302H039100 |
| Деталь: | TERMINAL DLP |
| Парткод: | 302H039110 |
| Деталь: | MOUNT POWER PWB |
| Парткод: | 302H039120 |
| Деталь: | MOUNT HV PWB |
| Парткод: | 302H039160 |
| Деталь: | MOUNT INLET |
| Парткод: | 302H039170 |
| Деталь: | MOUNT OPTION I/F |
| Парткод: | 302H039180 |
| Деталь: | TERMINAL TRANSFER R |
| Парткод: | 302H039190 |
| Деталь: | TERMINAL SEPARATION R |
| Парткод: | 302H039200 |
| Деталь: | LID HV TERMINAL |
| Парткод: | 302H039210 |
| Деталь: | MOUNT ENGINE MAIN C |
| Парткод: | 302JC39010 |
| Деталь: | GUIDE WIRE R |
| Парткод: | 302H039230 |
| Деталь: | GUIDE WIRE L |
| Парткод: | 302H039240 |
| Деталь: | MOUNT MAIN SW |
| Парткод: | 302H039260 |
| Деталь: | LID WIRE GUIDE |
| Парткод: | 302H039270 |
| Деталь: | GROUND PLATE OPE F |
| Парткод: | 302GR05140 |
| Деталь: | SHIELD MAIN TOP |
| Парткод: | 302JC39070 |
| Деталь: | FILM PROTECT A |
| Парткод: | 302H002290 |
| Деталь: | LID PRINTER BOARD |
| Парткод: | 302JC39030 |
| Деталь: | GUIDE WIRE C |
| Парткод: | 302JC39110 |
| Деталь: | WIRE LVU |
| Парткод: | 302JB46040 |
| Деталь: | WIRE MAIN MOTOR |
| Парткод: | 302H046280 |
| Деталь: | GUID CF CARD /45252C0006 A4 |
| Парткод: | 5MVX621SH003 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | WIRE LAMP INVERTER |
| Парткод: | 302H046770 |
| Деталь: | WIRE CONVEYING |
| Парткод: | 302H046300 |
| Деталь: | SPACER,KGPS-4S |
| Парткод: | M2108130 |
| Деталь: | SW SEESAW |
| Парткод: | 7SC010101+++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610011++H01 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | PARTS,PWB MAIN ASSY SP |
| Парткод: | 302JB94021 |
| Деталь: | 100PIN DIMM 64M |
| Парткод: | 5AAXAP072GEA++R |
| Деталь: | PARTS, PWB ENGINE ASSY,SP |
| Парткод: | 302JB94080 |
| Деталь: | WIRE DF I/F |
| Парткод: | 302H046320 |
| Деталь: | WIRE FINISHER SOCKET |
| Парткод: | 302GR46160 |
| Деталь: | WIRE LVU |
| Парткод: | 302H046180 |
| Деталь: | WIRE CASSETTE |
| Парткод: | 302H046120 |
| Деталь: | WIRE MAIN SW |
| Парткод: | 302H046441 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | PARTS LVU 200 |
| Парткод: | 302H093290 |
| Деталь: | PARTS LVU 100 |
| Парткод: | 302H093280 |
| Деталь: | WIRE LVU FAN |
| Парткод: | 302H046540 |
| Деталь: | WIRE INLET |
| Парткод: | 302H046560 |
| Деталь: | WIRE INTERLOCK JUNCTION |
| Парткод: | 302H046680 |
| Деталь: | COVER OP WIRE |
| Парткод: | 302H004800 |
| Деталь: | WIRE KEY COUNTER |
| Парткод: | 302H046790 |
| Деталь: | ACCESS.BAND |
| Парткод: | 7YZM420003++H01 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | GROUND PLATE SHIELD |
| Парткод: | 302JC39120 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610016++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | WIRE KEY CARD |
| Парткод: | 302H046800 |
| Деталь: | POWER CORD(120) |
| Парткод: | 3019527401 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | POWER CODE AS(240) |
| Парткод: | 3029927232 |
| Деталь: | POWER CORD 110 |
| Парткод: | 3065027601 |
| Деталь: | Блок проявки |
| Парткод: | DV-420 |
| Цена: | 18 000 ₽ |
| Деталь: | Главный редуктор, в сборе |
| Парткод: | DR-670 |
| Цена: | 8 000 ₽ |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | BELT CONVEYING |
| Парткод: | 2BL06320 |
| Деталь: | GUIDE B FEED |
| Парткод: | 2BL06330 |
| Деталь: | SPRING FEED JOINT |
| Парткод: | 2FG06070 |
| Деталь: | FRAME VERTICAL FEED |
| Парткод: | 302H006010 |
| Деталь: | GUIDE VERTICAL |
| Парткод: | 302H006040 |
| Деталь: | PLATE VERTICAL DRIVE |
| Парткод: | 302H006050 |
| Деталь: | GEAR Z31S-P18 FEED |
| Парткод: | 302H006080 |
| Деталь: | SPRING GUIDE VERTICAL |
| Парткод: | 302H006090 |
| Деталь: | GEAR Z30S VERTICAL IDLE |
| Парткод: | 302H006100 |
| Деталь: | GEAR Z20S JOINT FEED A |
| Парткод: | 302H006110 |
| Деталь: | GEAR Z20S JOINT FEED B |
| Парткод: | 302H006120 |
| Деталь: | HOLDER FEED SWITCH |
| Парткод: | 302H006300 |
| Деталь: | SPRING EARTH SW |
| Парткод: | 302H006360 |
| Деталь: | PLATE VERTICAL JOINT A |
| Парткод: | 302H006390 |
| Деталь: | PIN VERTICAL |
| Парткод: | 302H006400 |
| Деталь: | PLATE EARTH VERTICAL |
| Парткод: | 302H006410 |
| Деталь: | SPRING COVER HOOK |
| Парткод: | 302H006420 |
| Деталь: | SPRING EARTH PI |
| Парткод: | 302H006430 |
| Деталь: | BUSH 8 EW |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | WIRE CONVEYING UNIT |
| Парткод: | 302H046210 |
| Деталь: | PARTS ROLLER VERTICAL FEED A SP |
| Парткод: | 302H094090 |
| Деталь: | PARTS ROLLER VERTICAL FEED B SP |
| Парткод: | 302H094100 |
| Деталь: | PARTS CLUTCH FEED SP |
| Парткод: | 302H094210 |
| Деталь: | PARTS SWITCH CONVEYING SP |
| Парткод: | 302H094230 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | LOCK COVER R /40283V0068 A4 |
| Парткод: | 5MVX421DN003 |
| Деталь: | COVER LEFT FEED |
| Парткод: | 302H006210 |
| Деталь: | SPRING FEED |
| Парткод: | 302H006350 |
| Деталь: | SHAFT MID FEED |
| Парткод: | 302H024090 |
| Деталь: | PULLEY 15 DUPLEX |
| Парткод: | 3HY07120 |
| Деталь: | COVER VERTICAL INNER |
| Парткод: | 302H006380 |
| Деталь: | LABEL VERTICAL COVER |
| Парткод: | 302H034050 |
| Деталь: | STRAP VERTICAL COVER |
| Парткод: | 302H006200 |
| Деталь: | PARTS VERTICAL FEEED UNIT |
| Парткод: | 302H093080 |
| Деталь: | Ролик захвата бумаги в узле автоматической подачи документов |
| Парткод: | 36211110 |
| Цена: | 750 ₽ |
| Деталь: | Ролик подачи бумаги в узле автоматической подачи документов |
| Парткод: | 3BR07040 |
| Цена: | 420 ₽ |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | PULLEY MIDDLE FEED |
| Парткод: | 2FG06110 |
| Деталь: | COLLAR TRANS ROLLER |
| Парткод: | 302GR22110 |
| Деталь: | BASE MID FEED LOW |
| Парткод: | 302H024050 |
| Деталь: | BASE MID FEED UPPER |
| Парткод: | 302H024060 |
| Деталь: | GUIDE MID FEED |
| Парткод: | 302H024073 |
| Деталь: | PLATE MID FEED |
| Парткод: | 302H024080 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | 302H024100 |
| Деталь: | GEAR FEED Z29S |
| Парткод: | 302H024110 |
| Деталь: | GEAR FEED Z36SZ24S |
| Парткод: | 302H024120 |
| Деталь: | ACTUATOR MID FEED |
| Парткод: | 302H024130 |
| Деталь: | ACTUATOR REGIST |
| Парткод: | 302H024140 |
| Деталь: | PLATE MID FEED PI |
| Парткод: | 302H024150 |
| Деталь: | PLATE REG SW |
| Парткод: | 302H024160 |
| Деталь: | GEAR FEED Z30S CLUTCH |
| Парткод: | 302H024200 |
| Деталь: | SPRING GUIDE MID FEED |
| Парткод: | 302H024220 |
| Деталь: | SHAFT PULLEY FEED |
| Парткод: | 302H024230 |
| Деталь: | SPONGE CLEANER REG |
| Парткод: | 302H024240 |
| Деталь: | MOUNT CLEANER REG |
| Парткод: | 302H024350 |
| Деталь: | PLATE GROUND SHAFT |
| Парткод: | 302H024380 |
| Деталь: | PLATE GROUND ROLLER |
| Парткод: | 302H024391 |
| Деталь: | GEAR FEED Z35SZ23S |
| Парткод: | 302H024400 |
| Деталь: | PLATE GROUND REG SW |
| Парткод: | 302H024450 |
| Деталь: | FILM GUIDE MID FEED |
| Парткод: | 302H024460 |
| Деталь: | FILM GUIDE REG |
| Парткод: | 302H024470 |
| Деталь: | COLLAR JOINT |
| Парткод: | 302H024590 |
| Деталь: | SPRING ACTUATOR LOWER |
| Парткод: | 302H024600 |
| Деталь: | SHAFT PULLEY MID FEED |
| Парткод: | 302H024622 |
| Деталь: | FILM GUIDE HARNESS |
| Парткод: | 302H024650 |
| Деталь: | WIRE MIDDLE FEED |
| Парткод: | 302H046350 |
| Деталь: | WIRE RESIST |
| Парткод: | 302H046430 |
| Деталь: | PARTS CLUTCH FEED SP |
| Парткод: | 302H094210 |
| Деталь: | PULLEY MID FEED A ASSY |
| Парткод: | 302H024570 |
| Деталь: | PULLEY MID FEED B ASSY |
| Парткод: | 302H024580 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | PARTS MIDDLE FEEED UNIT |
| Парткод: | 302H093090 |
| Деталь: | PARTS PULLEY MID FEED ASSY SP |
| Парткод: | 302H094430 |
| Деталь: | LABEL L,HIGH TEMPERATURE CAUTION(E |
| Парткод: | 20305130 |
| Деталь: | PULLEY, PAPER FEED |
| Парткод: | 2AR07220 |
| Цена: | 1 600 ₽ |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | GUIDE FILM,SEPARATION PULLEY |
| Парткод: | 2AR07660 |
| Деталь: | BUSHING 6,REGISTRATION |
| Парткод: | 2BC06520 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PULLEY FEED A |
| Парткод: | 2BJ06010 |
| Цена: | 250 ₽ |
| Деталь: | PLATE LEADING FEED |
| Парткод: | 2BL07900 |
| Деталь: | SUPPORT PLATE FEED |
| Парткод: | 2BL07910 |
| Деталь: | SPRING SEPARATION |
| Парткод: | 2BL07990 |
| Деталь: | SHIELD PF |
| Парткод: | 302H009140 |
| Деталь: | PIN SCREW BIND 3X6S |
| Парткод: | 303KZ02180 |
| Деталь: | WIRE CASSETTE SW |
| Парткод: | 302H046600 |
| Деталь: | SHAFT,PAPER FEED |
| Парткод: | 302AR07252 |
| Цена: | 420 ₽ |
| Деталь: | SHAFT, SEPARATION |
| Парткод: | 302AR07261 |
| Деталь: | SHAFT,LEADING FEED |
| Парткод: | 302AR07271 |
| Деталь: | HEATER DEHUMIDIFIER 240 |
| Парткод: | 302FB25061 |
| Деталь: | HEATER DEHUMIDIFIER 120 |
| Парткод: | 302FB25052 |
| Деталь: | BUSHING,PRIMARY PAPER FEED |
| Парткод: | 302FG07070 |
| Деталь: | UPPER HOUSING,PAPER FEED |
| Парткод: | 302FG07252 |
| Деталь: | LOWER HOUSING,PAPER FEED |
| Парткод: | 302FG07260 |
| Деталь: | WEIGHTLEADING FEED PULLEY |
| Парткод: | 302FG07271 |
| Деталь: | ACTUATOR,PAPER EMPTY |
| Парткод: | 302FG07290 |
| Деталь: | HOLDER,ACTUATOR |
| Парткод: | 302FG07300 |
| Деталь: | REINFORCEMENT PRIMARY PAPER FEED |
| Парткод: | 302FG07310 |
| Деталь: | STOPPER,SUPPORT PLATE |
| Парткод: | 302FG07320 |
| Деталь: | GROUND PLATE,PRIMARY PAPER FEED |
| Парткод: | 302FG07330 |
| Деталь: | RETAINING PIN DRAWER |
| Парткод: | 302FZ03070 |
| Деталь: | COUPLING PAPER FEED |
| Парткод: | 302FZ32070 |
| Деталь: | LEVER SEPARATION RELEASE |
| Парткод: | 302GR06201 |
| Деталь: | GEAR 15 |
| Парткод: | 34922420 |
| Деталь: | WIRE CASSETTE SIZE |
| Парткод: | 302H046690 |
| Деталь: | MOTOR LIFT |
| Парткод: | 302GR44112 |
| Деталь: | WIRE PRIMARY FEED UNIT1 |
| Парткод: | 302GR46430 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | BRACKET GEAR JOINT FEED |
| Парткод: | 302H006140 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H01 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H02 |
| Деталь: | GEAR Z25S FEED C |
| Парткод: | 302H006180 |
| Деталь: | SHAFT PRIMARY FEED |
| Парткод: | 302H006190 |
| Деталь: | PT.SENSOR GP1A73AJ00/ BK |
| Парткод: | 5FNXGP1A73A++02 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | HOLDER FEED CLUTCH |
| Парткод: | 302H006240 |
| Деталь: | MOUNT FEED DRAWER |
| Парткод: | 302H006340 |
| Деталь: | MOUNT CASSETTE SWITCH |
| Парткод: | 302H006370 |
| Деталь: | PARTS CLUTCH FEED SP |
| Парткод: | 302H094210 |
| Деталь: | TORQUE LIMITER,PAPER FEED |
| Парткод: | 33906070 |
| Деталь: | GEAR 16,PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | LOWER BUSHING, PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | PARTS,DV-420,SP |
| Парткод: | 302FT93052 |
| Деталь: | GEAR HOPPER MOTOR |
| Парткод: | 302H014070 |
| Деталь: | GEAR Z50S HOPPER |
| Парткод: | 302H014080 |
| Деталь: | PARTS DC MOTOR SP |
| Парткод: | 302H094320 |
| Деталь: | COVER WIRE HOPPER |
| Парткод: | 302H014190 |
| Деталь: | PARTS MIDDLE HOPPER UNIT |
| Парткод: | 302H093210 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | MOUNT RIGHT HANDLE |
| Парткод: | 2BL02150 |
| Деталь: | GUIDE MIDDLE HOPPER |
| Парткод: | 302H014181 |
| Деталь: | SPRING DEV PUSH |
| Парткод: | 2C902080 |
| Деталь: | LEVER DEV PUSH |
| Парткод: | 2C902170 |
| Деталь: | SPRING DEV PUSH F |
| Парткод: | 2C902590 |
| Деталь: | PIN CASSETTE RAIL |
| Парткод: | 2FB06710 |
| Деталь: | RAIL DLP |
| Парткод: | 2FT02200 |
| Деталь: | SEAL SCANNER |
| Парткод: | 302DA12070 |
| Деталь: | PULLEY,CASSETTE RAIL |
| Парткод: | 302FG07020 |
| Деталь: | LEFT RAIL CASSETTE |
| Парткод: | 302FG07033 |
| Деталь: | LEVER LOCK CASSETTE |
| Парткод: | 302GR02221 |
| Деталь: | SPRING LEVER |
| Парткод: | 302GR02230 |
| Деталь: | PIN FRONT CASSETTE RAIL |
| Парткод: | 302GR02240 |
| Деталь: | RIGHT HANDLE MACHINE |
| Парткод: | 302GR02340 |
| Деталь: | HANDLE MACHINE |
| Парткод: | 302GR02350 |
| Деталь: | SPRING ISU LOW |
| Парткод: | 302H002280 |
| Деталь: | SPACER LSU |
| Парткод: | 302H002040 |
| Деталь: | LOWER PLATE MPF |
| Парткод: | 302H002050 |
| Деталь: | LOWER PLATE LSU |
| Парткод: | 302H002060 |
| Деталь: | UPPER PLATE DRUM |
| Парткод: | 302H002070 |
| Деталь: | LOWER PLATE DLP |
| Парткод: | 302H002080 |
| Деталь: | PLATE FUSER GUIDE |
| Парткод: | 302H002090 |
| Деталь: | PLATE FRONT LEFT |
| Парткод: | 302H002100 |
| Деталь: | SPACER DRUM |
| Парткод: | 302H002110 |
| Деталь: | MOUNT HANDLE FRONT LEFT |
| Парткод: | 302H002120 |
| Деталь: | PLATE POSITION A |
| Парткод: | 302H002130 |
| Деталь: | PLATE POSITION B |
| Парткод: | 302H002140 |
| Деталь: | PLATE EXIT FRONT |
| Парткод: | 302H002150 |
| Деталь: | BASE SCANNER UNIT |
| Парткод: | 302H002161 |
| Деталь: | MOUNT SCANNER UNIT L |
| Парткод: | 302H002180 |
| Деталь: | PLATE RIGHT TOP |
| Парткод: | 302H002190 |
| Деталь: | PLATE RIGHT MIDDLE |
| Парткод: | 302H002200 |
| Деталь: | PLATE POSITION C |
| Парткод: | 302H002210 |
| Деталь: | HOLDER DLP RAIL |
| Парткод: | 302H002220 |
| Деталь: | PLATE POSITION D |
| Парткод: | 302H002230 |
| Деталь: | RUBBER BASE |
| Парткод: | 302H002250 |
| Деталь: | SUPPORT COVER LEFT |
| Парткод: | 302H004720 |
| Деталь: | ADJUSTOR SCANNER |
| Парткод: | 302H002310 |
| Деталь: | MOUNT RUBBER SCANNER |
| Парткод: | 302H002320 |
| Деталь: | LOWER LEFT REINFORCE |
| Парткод: | 302H002330 |
| Деталь: | LOWER RIGHT REINFORCEMENT |
| Парткод: | 302H002340 |
| Деталь: | MOUNT REAR COVER A |
| Парткод: | 302H002350 |
| Деталь: | GROUND SCANNER |
| Парткод: | 302H002360 |
| Деталь: | PIN,DRAWER SIDE CONVEYING |
| Парткод: | 3CZ02240 |
| Деталь: | MOUNT COVER HINGE A |
| Парткод: | 302H004260 |
| Деталь: | MOUNT COVER HINGE B |
| Парткод: | 302H004290 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610016++H01 |
| Деталь: | PIN SCREW BIND 3X6S |
| Парткод: | 303KZ02180 |
| Деталь: | SHIELD SCREW |
| Парткод: | 302H002380 |
| Деталь: | SHIELD LSU LOW |
| Парткод: | 302H002371 |
| Деталь: | GROUND CONVEYING PLATE |
| Парткод: | 302H024561 |
| Деталь: | FILM PROTECT B |
| Парткод: | 302H002300 |
| Деталь: | PLATE LEFT GUIDE |
| Парткод: | 2FG17080 |
| Деталь: | STAY GUIDE MPF UPPER |
| Парткод: | 302H008420 |
| Деталь: | ACCESS,BUSHING |
| Парткод: | 7YZM110003++H01 |
| Деталь: | CLAMP,CKN-05(KITAGAWA) |
| Парткод: | M2105890 |
| Деталь: | SPONGE ORIGINAL SIZE |
| Парткод: | 2C912700 |
| Деталь: | CONTACT GLASS DP |
| Парткод: | 302H017220 |
| Деталь: | HOLDER GLASS DF |
| Парткод: | 2C912420 |
| Деталь: | LEFT SIZE INDICATOR |
| Парткод: | 302H017160 |
| Деталь: | PLATE SHADING |
| Парткод: | 302H017200 |
| Деталь: | CONTACT GLASS |
| Парткод: | 2C912250 |
| Деталь: | LABEL SIZE (METRIC) |
| Парткод: | 2C912440 |
| Деталь: | LABEL SIZE (INCH) |
| Парткод: | 2C912450 |
| Деталь: | REAR SIZE INDICATOR (M) |
| Парткод: | 302H017340 |
| Деталь: | REAR SIZE INDICATOR (I) |
| Парткод: | 302H017350 |
| Деталь: | FRONT SIZE INDICATOR |
| Парткод: | 2C912600 |
| Деталь: | COVER ISU REAR |
| Парткод: | 302H004200 |
| Деталь: | PIN SCANNER RETAINING |
| Парткод: | 302GR17180 |
| Деталь: | PARTS LK-670 |
| Парткод: | 302H093060 |
| Деталь: | COVER LSU |
| Парткод: | 302H019020 |
| Деталь: | COVER ISU FRONT |
| Парткод: | 302H004171 |
| Деталь: | COVER ISU RIGHT |
| Парткод: | 302H004190 |
| Деталь: | COVER ISU LEFT |
| Парткод: | 302H004180 |
| Деталь: | CAP MOUNT DP |
| Парткод: | 302H004550 |
| Деталь: | SPONGE SEAL A |
| Парткод: | 302H033210 |
| Деталь: | SHEET FRAME LOW |
| Парткод: | 302H033240 |
| Деталь: | PARTS CONTACT GLASS DP |
| Парткод: | 302H093300 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | HOLDER FEED SWITCH |
| Парткод: | 302H006300 |
| Деталь: | SHAFT MID FEED |
| Парткод: | 302H024090 |
| Деталь: | BUSH 8 EW |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | FRAME DU |
| Парткод: | 302H029011 |
| Деталь: | GROUND PLATE DU |
| Парткод: | 302H029020 |
| Деталь: | BELT DU 254 |
| Парткод: | 302H029030 |
| Деталь: | SPRING DU FEED |
| Парткод: | 302H029060 |
| Деталь: | GEAR Z25S |
| Парткод: | 302H029070 |
| Деталь: | PLATE DU DRIVE |
| Парткод: | 302H029080 |
| Деталь: | SPRING DU DRIVE |
| Парткод: | 302H029090 |
| Деталь: | JUNCTION PLATE DU |
| Парткод: | 302H029100 |
| Деталь: | PULLEY 26 DU |
| Парткод: | 302H029110 |
| Деталь: | GROUND DUPLEX PI |
| Парткод: | 302H029130 |
| Деталь: | PLATE CONTACT CONVEYING |
| Парткод: | 302H029140 |
| Деталь: | PARTS CLUTCH FEED SP |
| Парткод: | 302H094210 |
| Деталь: | PARTS SWITCH CONVEYING SP |
| Парткод: | 302H094230 |
| Деталь: | PARTS DUPLEX A SP |
| Парткод: | 302H094380 |
| Деталь: | PARTS DUPLEX B SP |
| Парткод: | 302H094390 |
| Деталь: | WIRE DU |
| Парткод: | 302H046370 |
| Деталь: | PULLEY 15 DUPLEX |
| Парткод: | 3HY07120 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC02B1001+H01 |
| Деталь: | ACCESS.BAND |
| Парткод: | 7YZM420003++H01 |
| Деталь: | STOPPER SHUTTER |
| Парткод: | 302H024510 |
| Деталь: | COVER DU WIRE |
| Парткод: | 302H024500 |
| Деталь: | PARTS DUPLEX UNIT |
| Парткод: | 302H093200 |
| Деталь: | MAIN PCB ASSY (SP), DCP-T300 FOR RUS/BLT/CEE/NAF (PRESET 74 CODE:0054) |
| Парткод: | FK-671 |
| Цена: | 13 600 ₽ |
| Деталь: | GEAR,TONER ROLLER |
| Парткод: | 29415100 |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | PULLEY FEED A |
| Парткод: | 2BJ06010 |
| Цена: | 250 ₽ |
| Деталь: | COVER BYPASSTRAY |
| Парткод: | 2BL06600 |
| Деталь: | STAY LIFTPLATE |
| Парткод: | 2BL06650 |
| Деталь: | CAM BYPASS |
| Парткод: | 2BL06680 |
| Деталь: | MOUNT BYPASSDRIVE |
| Парткод: | 2BL06690 |
| Деталь: | GEAR 55/15 |
| Парткод: | 2BL06720 |
| Деталь: | JOINT RETARD |
| Парткод: | 2BL06850 |
| Деталь: | SPRING JOINTRETARD |
| Парткод: | 2BL06870 |
| Деталь: | FILM BYPASS |
| Парткод: | 2BL06880 |
| Деталь: | STOPPER GEAR 8-25 |
| Парткод: | 2BL06990 |
| Деталь: | SPRING BYPASS |
| Парткод: | 2BL07860 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 302BC07861 |
| Деталь: | COVER BYPASSUNIT |
| Парткод: | 302BL06531 |
| Деталь: | SHAFT RETARD |
| Парткод: | 302BL06751 |
| Деталь: | SHAFT BYPASSCAM |
| Парткод: | 302BL06761 |
| Деталь: | SHAFT BYPASS |
| Парткод: | 302BL06771 |
| Деталь: | BASE BYPASS |
| Парткод: | 302GR08011 |
| Деталь: | PLATE LIFT BYPASS |
| Парткод: | 302GR08021 |
| Деталь: | COVER CURSOR |
| Парткод: | 302GR08030 |
| Деталь: | FRONT CURSOR BYPASS |
| Парткод: | 302GR08040 |
| Деталь: | REAR CURSOR BYPASS |
| Парткод: | 302GR08050 |
| Деталь: | MOUNT SIZE PWB |
| Парткод: | 302GR08060 |
| Деталь: | RACK CURSOR |
| Парткод: | 302GR08071 |
| Деталь: | TABLE BYPASS |
| Парткод: | 302GR08080 |
| Деталь: | LABEL SET PAPER CAUTION A |
| Парткод: | 302GR34091 |
| Деталь: | LABEL SET PAPER CAUTION E |
| Парткод: | 302GR34102 |
| Деталь: | LABEL SET PAPER CAUTION J |
| Парткод: | 302GR34111 |
| Деталь: | LABEL BYPASS SIZE |
| Парткод: | 302GR34122 |
| Деталь: | LABEL SET PAPER CAUTION |
| Парткод: | 302GR34260 |
| Деталь: | LABEL SET PAPER CAUTION TW |
| Парткод: | 302GR34411 |
| Деталь: | CLUTCH FEED |
| Парткод: | 302GR44120 |
| Деталь: | CLUTCH FEED B |
| Парткод: | 302GR44131 |
| Деталь: | WIRE BYPASS UNIT |
| Парткод: | 302GR46230 |
| Деталь: | WIRE BYPASS TRAY |
| Парткод: | 302GR46270 |
| Деталь: | CUT WASHER MPF 5 |
| Парткод: | 302H008180 |
| Деталь: | SPRING RETARD |
| Парткод: | 302H008290 |
| Деталь: | CUSHION MPF |
| Парткод: | 302H008330 |
| Деталь: | SWITCH BYPASS SIZE |
| Парткод: | 302H044100 |
| Деталь: | JOINT,BYPASS PICKUP |
| Парткод: | 303A206131 |
| Деталь: | GEAR 16,PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | TORQUE LIMITER,BYPASS |
| Парткод: | 33906430 |
| Деталь: | FRICTION PLATE,BYPASS LEADING FEED |
| Парткод: | 34806490 |
| Деталь: | GEAR 18,CASSETTE |
| Парткод: | 34907141 |
| Деталь: | ARM,BYPASS PE |
| Парткод: | 3A206100 |
| Деталь: | HOLDER,RETARD |
| Парткод: | 3A206170 |
| Деталь: | MOUNT,BYPASS PE SWITCH |
| Парткод: | 3A206210 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | UPPER PULLEY,BYPASS |
| Парткод: | 61706770 |
| Цена: | 1 900 ₽ |
| Деталь: | GEAR,16 BYPASS PULLEY |
| Парткод: | 66006810 |
| Деталь: | PIN,CASSETTE WORK PLATE |
| Парткод: | 66007310 |
| Деталь: | GEAR 30, FD EJECT IDLE |
| Парткод: | 72321350 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | EDGING, EDS-0607M(KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | MINI CLAMP, UAMS-02WL-0 (KITAGAWA) |
| Парткод: | M2105210 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | PLATE BYPASS HOLD |
| Парткод: | 2BL06890 |
| Деталь: | SPACING CLIP /VSC-10 XX |
| Парткод: | 5MVX431NN001 |
| Деталь: | PARTS MPF UNIT |
| Парткод: | 302H093110 |
| Деталь: | PULLEY EXIT B |
| Парткод: | 2BL21450 |
| Деталь: | PCB EJECT SW ASSY |
| Парткод: | 2C901060 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 2C904550 |
| Деталь: | GEAR 23 EXIT |
| Парткод: | 2C921120 |
| Деталь: | SPRING LINK |
| Парткод: | 2C921290 |
| Деталь: | BELT FEED HANDLE |
| Парткод: | 2FB17260 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SOLENOID FEED SHIFT |
| Парткод: | 302GR44160 |
| Деталь: | FRAME EXIT UPPER |
| Парткод: | 302H028010 |
| Деталь: | ACTUATOR EXIT INNER |
| Парткод: | 302H028040 |
| Деталь: | ACTUATOR EXIT FEED |
| Парткод: | 302H028050 |
| Деталь: | PULLEY EJECT T32 |
| Парткод: | 302H028070 |
| Деталь: | GUIDE SEPARATE INNER |
| Парткод: | 302H028090 |
| Деталь: | LEVER LINK |
| Парткод: | 302H028100 |
| Деталь: | ARM LINK |
| Парткод: | 302H028120 |
| Деталь: | PLATE EXIT A |
| Парткод: | 302H028150 |
| Деталь: | PLATE EXIT B |
| Парткод: | 302H028160 |
| Деталь: | GEAR EXIT FEED 21 |
| Парткод: | 302H028170 |
| Деталь: | GEAR EXIT FEED 17 |
| Парткод: | 302H028180 |
| Деталь: | GEAR EXIT FEED 13 |
| Парткод: | 302H028190 |
| Деталь: | PLATE EXIT JOINT |
| Парткод: | 302H028200 |
| Деталь: | SPRING EXIT JOINT |
| Парткод: | 302H028210 |
| Деталь: | LINK SOLENOID |
| Парткод: | 302H028220 |
| Деталь: | PULLEY EXIT FEED |
| Парткод: | 302H028230 |
| Деталь: | GROUND PLATE EXIT A |
| Парткод: | 302H028250 |
| Деталь: | GROUND PLATE EXIT B |
| Парткод: | 302H028260 |
| Деталь: | PLATE ARM LINK |
| Парткод: | 302H028300 |
| Деталь: | SHAFT SEP FEED |
| Парткод: | 302H028400 |
| Деталь: | SPRING EXIT FEED |
| Парткод: | 302H028410 |
| Деталь: | SPRING ACTUATOR INNER |
| Парткод: | 302H028520 |
| Деталь: | SPRING SOLENOID |
| Парткод: | 302H028540 |
| Деталь: | PULLEY EXIT |
| Парткод: | 302H028570 |
| Деталь: | FILM EXIT |
| Парткод: | 302H028580 |
| Деталь: | FILM EXIT INNER |
| Парткод: | 302H028600 |
| Деталь: | FILM EXIT A |
| Парткод: | 302H028610 |
| Деталь: | FILM EXIT B |
| Парткод: | 302H028620 |
| Деталь: | FILM EXIT C |
| Парткод: | 302H028630 |
| Деталь: | FILM EXIT D |
| Парткод: | 302H028650 |
| Деталь: | FRAME EXIT LOWER A |
| Парткод: | 302H028660 |
| Деталь: | WIRE EJECT UNIT |
| Парткод: | 302H046140 |
| Деталь: | PARTS ROLLER EXIT FEED SP |
| Парткод: | 302H094360 |
| Деталь: | PARTS ROLLER EXIT INNER SP |
| Парткод: | 302H094370 |
| Деталь: | STATIC ELIMINATOR B,EJECT |
| Парткод: | 34821210 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | ONE WAY CLUTCH /A-49 MPF A4 |
| Парткод: | 5AAVCLTCH018 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | EDGING,EDS-0607L(KITAGAWA) |
| Парткод: | M2104390 |
| Деталь: | GEAR EXIT 73/21 |
| Парткод: | 302H028290 |
| Деталь: | PARTS EXIT UNIT |
| Парткод: | 302H093190 |
| Деталь: | STUD SCREW SC |
| Парткод: | 2BG12430 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 2C904550 |
| Деталь: | ROLLER FINISH UP |
| Парткод: | 302H027010 |
| Деталь: | ROLLER FINISH LOW |
| Парткод: | 302H027020 |
| Деталь: | COVER LEFT OP |
| Парткод: | 302H027030 |
| Деталь: | Guide Cover |
| Парткод: | 302H027040 |
| Деталь: | GUIDE SEPARATE FIN |
| Парткод: | 302H027050 |
| Деталь: | ARM SEPARATE FIN |
| Парткод: | 302H027060 |
| Деталь: | GEAR EXIT FIN 17 |
| Парткод: | 302H027090 |
| Деталь: | GEAR EXIT FIN 14 |
| Парткод: | 302H027100 |
| Деталь: | FRONT PLATE FIN |
| Парткод: | 302H027110 |
| Деталь: | REAR PLATE FIN |
| Парткод: | 302H027120 |
| Деталь: | PLATE SEP FIN |
| Парткод: | 302H027130 |
| Деталь: | GUIDE INSERT |
| Парткод: | 302H027150 |
| Деталь: | GUIDE SEPARATE FEED |
| Парткод: | 302H028310 |
| Деталь: | ARM SEPARATE FEED A |
| Парткод: | 302H028350 |
| Деталь: | ARM SEPARATE FEED B |
| Парткод: | 302H028360 |
| Деталь: | SPRING SEPARATE FEED |
| Парткод: | 302H028370 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | ONE WAY CLUTCH /A-49 MPF A4 |
| Парткод: | 5AAVCLTCH018 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | BEARING, DRIVE |
| Парткод: | 68822330 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBER0R0U001H01 |
| Деталь: | AK-670/ATTACHMENT KIT |
| Парткод: | 1702H00UN0 |
| Деталь: | SHIELD HEATER DRUM |
| Парткод: | 302H002260 |
| Деталь: | BRUSH CLEANER |
| Парткод: | 2BL16220 |
| Деталь: | COVER CONN |
| Парткод: | 302GR39190 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | SPACING CLIP /VSC-10 XX |
| Парткод: | 5MVX431NN001 |
| Деталь: | LID INNER COVER |
| Парткод: | 302H004760 |
| Деталь: | GUIDE WIRE R |
| Парткод: | 302H039230 |
| Деталь: | LID WIRE GUIDE |
| Парткод: | 302H039270 |
| Деталь: | COVER INNER TOP |
| Парткод: | 302H004520 |
| Деталь: | COVER INNER LOW |
| Парткод: | 302H004210 |
| Деталь: | LEVER CONT RELEASE |
| Парткод: | 302H004530 |
| Деталь: | SPRING CONT RELEASE |
| Парткод: | 302H004540 |
| Деталь: | LABEL RADIATION |
| Парткод: | 2BL05150 |
| Деталь: | MOUNT SPEAKER |
| Парткод: | 302H004330 |
| Деталь: | PARTS HEATER DRUM SP |
| Парткод: | 302H094240 |
| Деталь: | PARTS,HIGH VOLTAGE,SP |
| Парткод: | 302H094250 |
| Цена: | 9 200 ₽ |
| Деталь: | PARTS, HUMIDITY SENSOR,SP |
| Парткод: | 302H094300 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610013++H01 |
| Деталь: | MOUNT INTERLOCK SW |
| Парткод: | 302H004320 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | LID RIGHT TOP PLATE |
| Парткод: | 302JC39080 |
| Деталь: | LID RIGHT PLATE |
| Парткод: | 302JC39100 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC09B1106+H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | WIRE DH JUNCTION |
| Парткод: | 302H046410 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | WIRE FRONT |
| Парткод: | 302H046251 |
| Деталь: | WIRE HVU |
| Парткод: | 302H046260 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | WIRE MPF |
| Парткод: | 302JB46090 |
| Деталь: | WIRE PRIMARY |
| Парткод: | 302H046380 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610011++H01 |
| Деталь: | SPONGE SEAL B |
| Парткод: | 302H033220 |
| Деталь: | FILM SEAL C |
| Парткод: | 302H033230 |
| Деталь: | EMBLEM LOGO |
| Парткод: | 302GR04140 |
| Деталь: | SEAL EMBLEM |
| Парткод: | 302GR04340 |
| Деталь: | COVER EMBLEM B (25ppm) |
| Парткод: | 302JB04030 |
| Деталь: | COVER EMBLEM B (30ppm) |
| Парткод: | 302JC04080 |
| Деталь: | LABEL ENERGY STAR |
| Парткод: | 302G634070 |
| Деталь: | LID KMAS |
| Парткод: | 2C912430 |
| Деталь: | COVER LSU LOW |
| Парткод: | 302H002270 |
| Деталь: | COVER FRONT LEFT LOW |
| Парткод: | 302H004770 |
| Деталь: | COVER FRONT LEFT MIDDLE |
| Парткод: | 302H004780 |
| Деталь: | LID COVER LEFT |
| Парткод: | 302BL04301 |
| Деталь: | COVER REAR PWB |
| Парткод: | 302JC04070 |
| Деталь: | COVER OZONE |
| Парткод: | 302GR04250 |
| Деталь: | MAGNET CLIP DISH |
| Парткод: | 302GR04370 |
| Деталь: | SEAL MAGNET |
| Парткод: | 302GR04380 |
| Деталь: | COVER FRONT |
| Парткод: | 302H004012 |
| Деталь: | COVER FRONT RIGHT |
| Парткод: | 302H004040 |
| Деталь: | COVER CASS HEATER |
| Парткод: | 302H004690 |
| Деталь: | COVER TRAY |
| Парткод: | 302H004060 |
| Деталь: | COVER TRAY REAR |
| Парткод: | 302H004070 |
| Деталь: | COVER TRAY RIGHT |
| Парткод: | 302H004080 |
| Деталь: | COVER EJECT UPPER |
| Парткод: | 302H004090 |
| Деталь: | COVER FRONT TOP |
| Парткод: | 302JC04090 |
| Деталь: | COVER LEFT FRONT |
| Парткод: | 302H004110 |
| Деталь: | COVER LEFT REAR |
| Парткод: | 302H004120 |
| Деталь: | COVER LEFT MIDDLE |
| Парткод: | 302H004130 |
| Деталь: | COVER RIGHT LOW |
| Парткод: | 302JC04010 |
| Деталь: | COVER RIGHT MIDDLE |
| Парткод: | 302H004151 |
| Деталь: | COVER OPE LOW |
| Парткод: | 302H004161 |
| Деталь: | MOUNT REAR COVER L |
| Парткод: | 302H004570 |
| Деталь: | MOUNT REAR COVER R |
| Парткод: | 302H004581 |
| Деталь: | MOUNT REAR DUCT |
| Парткод: | 302H004600 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 302H004650 |
| Деталь: | COVER BASE DISH |
| Парткод: | 302H004220 |
| Деталь: | CLIP DISH |
| Парткод: | 302H004230 |
| Деталь: | COVER MAIN SW |
| Парткод: | 302H004241 |
| Деталь: | COVER REAR |
| Парткод: | 302JC04020 |
| Деталь: | HINGE FRONT COVER A |
| Парткод: | 302H004270 |
| Деталь: | PIN HINGE A |
| Парткод: | 302H004280 |
| Деталь: | HINGE FRONT COVER B |
| Парткод: | 302H004300 |
| Деталь: | PIN HINGE B |
| Парткод: | 302H004310 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302H004560 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302H004660 |
| Деталь: | FILTER OZONE B |
| Парткод: | 302H033180 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | LABEL CAUTION |
| Парткод: | 302H034170 |
| Деталь: | LABEL CAUTION GEAR |
| Парткод: | 302H034180 |
| Деталь: | LABEL CONVEYING JAM |
| Парткод: | 302H034140 |
| Деталь: | GUIDE CASE |
| Парткод: | 302FB04970 |
| Деталь: | SPONGE CLEANER REG |
| Парткод: | 302H024240 |
| Деталь: | LABEL SW CAUTION ENG |
| Парткод: | 302JC34100 |
| Деталь: | LABEL CAUTION HG |
| Парткод: | 302DC05120 |
| Деталь: | LABEL SW CAUTION EXP SET |
| Парткод: | 302JC34110 |
| Деталь: | PARTS COVER EMBLEM SP (25ppm) |
| Парткод: | 302JB94010 |
| Деталь: | PARTS COVER EMBLEM SP (30ppm) |
| Парткод: | 302JC94010 |
| Деталь: | Крышка лотка ручной подачи бумаги |
| Парткод: | 302BL06601 |
| Цена: | 3 700 ₽ |
| Деталь: | 2C916070 |
| Парткод: | 2C916070 |
| Деталь: | 2C916080 |
| Парткод: | 2C916080 |
| Деталь: | 2C916090 |
| Парткод: | 2C916090 |
| Деталь: | 2C916180 |
| Парткод: | 2C916180 |
| Деталь: | 2C916250 |
| Парткод: | 2C916250 |
| Деталь: | 2C916260 |
| Парткод: | 2C916260 |
| Деталь: | 2C917070 |
| Парткод: | 2C917070 |
| Деталь: | 2DA27020 |
| Парткод: | 2DA27020 |
| Деталь: | 2FT17030 |
| Парткод: | 2FT17030 |
| Деталь: | 2H022040 |
| Парткод: | 302H022040 |
| Деталь: | 2H022050 |
| Парткод: | 302H022050 |
| Деталь: | 2H022090 |
| Парткод: | 302H022090 |
| Деталь: | 2H022130 |
| Парткод: | 302H022130 |
| Деталь: | 2H024040 |
| Парткод: | 302H024040 |
| Деталь: | 2H024090 |
| Парткод: | 302H024090 |
| Деталь: | 2H024180 |
| Парткод: | 302H024180 |
| Деталь: | 2H024190 |
| Парткод: | 302H024190 |
| Деталь: | 2H024210 |
| Парткод: | 302H024210 |
| Деталь: | 2H024250 |
| Парткод: | 302H024250 |
| Деталь: | 2H024260 |
| Парткод: | 302H024260 |
| Деталь: | 2H024270 |
| Парткод: | 302H024270 |
| Деталь: | 2H024281 |
| Парткод: | 302H024281 |
| Деталь: | 2H024290 |
| Парткод: | 302H024290 |
| Деталь: | 2H024300 |
| Парткод: | 302H024300 |
| Деталь: | 2H024310 |
| Парткод: | 302H024310 |
| Деталь: | 2H024321 |
| Парткод: | 302H024321 |
| Деталь: | 2H024331 |
| Парткод: | 302H024331 |
| Деталь: | 2H024340 |
| Парткод: | 302H024340 |
| Деталь: | 2H024610 |
| Парткод: | 302H024610 |
| Деталь: | 2H024630 |
| Парткод: | 302H024630 |
| Деталь: | 2H024680 |
| Парткод: | 302H024680 |
| Деталь: | 2H024691 |
| Парткод: | 302H024691 |
| Деталь: | 2H024700 |
| Парткод: | 302H024700 |
| Деталь: | 2H024710 |
| Парткод: | 302H024710 |
| Деталь: | 2H024730 |
| Парткод: | 302H024730 |
| Деталь: | 2H046470 |
| Парткод: | 302H046470 |
| Деталь: | 2H094140 |
| Парткод: | 302H094140 |
| Деталь: | 3HY07120 |
| Парткод: | 3HY07120 |
| Деталь: | YZ052580 |
| Парткод: | 7YZM420003++H01 |
| Деталь: | YZ023340 |
| Парткод: | 7YZM610007++H01 |
| Деталь: | YZ042980 |
| Парткод: | 7YZM610009++H01 |
| Деталь: | 2H024360 |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | 2H094220 |
| Парткод: | 302H094220 |
| Деталь: | 2H024420 |
| Парткод: | 302H024420 |
| Деталь: | 2H024430 |
| Парткод: | 302H024430 |
| Деталь: | 2C917100 |
| Парткод: | 2C917100 |
| Деталь: | 2C917110 |
| Парткод: | 2C917110 |
| Деталь: | 2C917180 |
| Парткод: | 2C917180 |
| Деталь: | 2FT17020 |
| Парткод: | 2FT17020 |
| Деталь: | 2GR22110 |
| Парткод: | 302GR22110 |
| Деталь: | 2H022010 |
| Парткод: | 302H022010 |
| Деталь: | 2H022020 |
| Парткод: | 302H022020 |
| Деталь: | 2H022100 |
| Парткод: | 302H022100 |
| Деталь: | 2H022110 |
| Парткод: | 302H022110 |
| Деталь: | 2H022140 |
| Парткод: | 302H022140 |
| Деталь: | 2H022070 |
| Парткод: | 302H022070 |
| Деталь: | 2H022080 |
| Парткод: | 302H022080 |
| Деталь: | 2H022030 |
| Парткод: | 302H022030 |
| Деталь: | 2H022120 |
| Парткод: | 302H022120 |
| Деталь: | 2BC06510 |
| Парткод: | 2BC06510 |
| Деталь: | 2BC06910 |
| Парткод: | 2BC06910 |
| Деталь: | 2BC06980 |
| Парткод: | 2BC06980 |
| Деталь: | 2C907130 |
| Парткод: | 2C907130 |
| Деталь: | 2H024440 |
| Парткод: | 302H024440 |
| Деталь: | 2H024530 |
| Парткод: | 302H024530 |
| Деталь: | 2H024540 |
| Парткод: | 302H024540 |
| Деталь: | 2H024550 |
| Парткод: | 302H024550 |
| Деталь: | M21AH010 |
| Парткод: | M21AH010 |
| Деталь: | 2H024020 |
| Парткод: | 302H024020 |
| Деталь: | 2H093180 |
| Парткод: | 302H093180 |
| Деталь: | 2H093050 |
| Парткод: | 302H093050 |
| Деталь: | DUCT BASE |
| Парткод: | 302H033011 |
| Деталь: | DUCT LID H |
| Парткод: | 302H033020 |
| Деталь: | DUCT LID G |
| Парткод: | 302H033100 |
| Деталь: | DUCT LID J |
| Парткод: | 302H033120 |
| Деталь: | DUCT PLATE |
| Парткод: | 302H033030 |
| Деталь: | LABEL F1 |
| Парткод: | 302GR34290 |
| Деталь: | HOLDER FILTER A |
| Парткод: | 302H033050 |
| Деталь: | FILTER DUST A |
| Парткод: | 302H033060 |
| Деталь: | DUCT REAR LOWER |
| Парткод: | 302H033080 |
| Деталь: | DUCT REAR UPPER |
| Парткод: | 302H033090 |
| Деталь: | DUCT REAR B LOWER |
| Парткод: | 302H033130 |
| Деталь: | DUCT REAR B UPPER |
| Парткод: | 302H033140 |
| Деталь: | SHEET DUCT |
| Парткод: | 302H033160 |
| Деталь: | PARTS FAN MAIN DUCT SP |
| Парткод: | 302H094460 |
| Деталь: | FAN DP |
| Парткод: | 3H627280 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | R/W MODULE 26X45 |
| Парткод: | 302F845040 |
| Деталь: | WIRE RFID |
| Парткод: | 302GR46590 |
| Деталь: | CONT SENSOR ASSY |
| Парткод: | 302H001170 |
| Деталь: | PARTS THERMISTOR SP |
| Парткод: | 302H094470 |
| Деталь: | LID DUCT |
| Парткод: | 302H039290 |
| Деталь: | SPONGE REAR FAN |
| Парткод: | 302H033190 |
| Деталь: | GROUND REAR COVER |
| Парткод: | 302H039330 |
| Деталь: | DUCT BOTTOM |
| Парткод: | 302H033040 |
| Деталь: | PARTS HOLDER FILTER A SP |
| Парткод: | 302H094401 |
| Деталь: | PLATE NUMBER |
| Парткод: | 2BL04310 |
| Деталь: | PLATE NUMBER 2 |
| Парткод: | 2BL04370 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 2C904550 |
| Деталь: | PIN CURSOR |
| Парткод: | 2FB07050 |
| Деталь: | SPRING CURSOR |
| Парткод: | 2FB07060 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | SHAFT, WORK PLATE |
| Парткод: | 302AR07041 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 302BC07861 |
| Деталь: | PLATE SIZE C |
| Парткод: | 302FB05200 |
| Деталь: | PLATE SIZE IN |
| Парткод: | 302FB05210 |
| Деталь: | LEVER CURSOR A |
| Парткод: | 302FB07032 |
| Деталь: | LEVER CURSOR B |
| Парткод: | 302FB07042 |
| Деталь: | PIN CASSETTE |
| Парткод: | 302FB07420 |
| Деталь: | LABEL PAPER SIZE R1 |
| Парткод: | 302FZ09141 |
| Деталь: | LEVER CASSETTE |
| Парткод: | 302GR09051 |
| Деталь: | RAIL CURSOR R |
| Парткод: | 302GR09060 |
| Деталь: | LID PAPER SIZE |
| Парткод: | 302GR09070 |
| Деталь: | RAIL CURSOR A |
| Парткод: | 302GR09082 |
| Деталь: | Support Plate |
| Парткод: | 302GR09090 |
| Деталь: | SPRING LEVER CASSETTE |
| Парткод: | 302GR09120 |
| Деталь: | SHAFT PULLEY |
| Парткод: | 302GR09130 |
| Деталь: | SHAFT HANDLE |
| Парткод: | 302GR09140 |
| Деталь: | WORK PLATE HANDLE |
| Парткод: | 302GR09150 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302GR09160 |
| Деталь: | PLATE SIZE INCH |
| Парткод: | 302GR09201 |
| Деталь: | SEAL DETECTION PLATE |
| Парткод: | 302GR09210 |
| Деталь: | FILM PWB COVER |
| Парткод: | 302GR09250 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09991 |
| Деталь: | LABEL PAPER SIZE |
| Парткод: | 302GR34022 |
| Деталь: | WIRE CASSETTE UNIT |
| Парткод: | 302GR46450 |
| Деталь: | CASSETTE |
| Парткод: | 302H009010 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302H009020 |
| Деталь: | COVER CASSETTE HANDLE |
| Парткод: | 302H009030 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 302H009040 |
| Деталь: | JOINT HANDLE CASSETTE |
| Парткод: | 302H009050 |
| Деталь: | ADJUSTING PLATE CASSETTE |
| Парткод: | 302H009060 |
| Деталь: | WORK PLATE LIFT CASSETTE |
| Парткод: | 302H009070 |
| Деталь: | FRONT CURSOR CASSETTE |
| Парткод: | 302H009080 |
| Деталь: | REAR CURSOR CASSETTE |
| Парткод: | 302H009090 |
| Деталь: | BASE CASSETTE |
| Парткод: | 302H009101 |
| Деталь: | CURSOR C CASSETTE |
| Парткод: | 302H009110 |
| Деталь: | PLATE CASSETTE EARTH |
| Парткод: | 302H009120 |
| Деталь: | LABEL PAPER SET |
| Парткод: | 302H034070 |
| Деталь: | LABEL CASSETTE OPERATION |
| Парткод: | 302H034120 |
| Деталь: | LABEL PAPER UPPER LIMIT |
| Парткод: | 302H034210 |
| Деталь: | DETECTION PLATE,PAPER SIZE |
| Парткод: | 33907170 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | PULLEY,CASSETTE |
| Парткод: | 34907150 |
| Деталь: | PLATE NUMBER4 |
| Парткод: | 3CF04060 |
| Деталь: | RETAINER M4 |
| Парткод: | 3CY06030 |
| Деталь: | RACK CURSOR |
| Парткод: | 3CY06090 |
| Деталь: | GEAR 20,CURSOR |
| Парткод: | 3CY06100 |
| Деталь: | PLATE NUMBER 3 /3CF0405 A4 |
| Парткод: | 5MVX321CE001 |
| Деталь: | CUSHION,CASSETTE R |
| Парткод: | 60907170 |
| Деталь: | SPRING, PAD |
| Парткод: | 66106080 |
| Деталь: | PAD,CASSETTE |
| Парткод: | 66107100 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H01 |
| Деталь: | PARTS CT-670 |
| Парткод: | 302H093101 |
| Деталь: | GEAR FUSER Z28 |
| Парткод: | 2C920180 |
| Деталь: | SEAL DISCHAGER |
| Парткод: | 2C920320 |
| Деталь: | BEARING PRESSURE |
| Парткод: | 2C920330 |
| Деталь: | BUSH HEAT R |
| Парткод: | 302F725070 |
| Деталь: | BUSH HEAT L |
| Парткод: | 302F725080 |
| Деталь: | STATIC ELIMINATOR HEAT ROLLER |
| Парткод: | 302F725430 |
| Деталь: | THERMISTOR ASSY |
| Парткод: | 302F925430 |
| Деталь: | COVER PCB FIXING |
| Парткод: | 302FT20101 |
| Деталь: | THERMISTOR FUSER |
| Парткод: | 302GJ25560 |
| Деталь: | RIGHT FRAME FUSER |
| Парткод: | 302H025011 |
| Деталь: | LEFT FRAME FUSER |
| Парткод: | 302H025020 |
| Деталь: | GEAR FUSER Z46 |
| Парткод: | 302H025030 |
| Деталь: | FRONT GUIDE FUSER |
| Парткод: | 302H025040 |
| Деталь: | REAR GUIDE FUSER |
| Парткод: | 302H025050 |
| Деталь: | COVER HEATER F |
| Парткод: | 302H025060 |
| Деталь: | COVER HEATER R |
| Парткод: | 302H025070 |
| Деталь: | GROUND PLATE HEAT R |
| Парткод: | 302H025090 |
| Деталь: | GROUND PLATE PRESS A |
| Парткод: | 302H025150 |
| Деталь: | GROUND PLATE PRESS B |
| Парткод: | 302H025160 |
| Деталь: | PLATE HOLDER |
| Парткод: | 302H025180 |
| Деталь: | FRONT PRESSING PLATE |
| Парткод: | 302H025190 |
| Деталь: | REAR PRESSING PLATE |
| Парткод: | 302H025200 |
| Деталь: | COVER FUSER UNIT |
| Парткод: | 302H025250 |
| Деталь: | SPRING FUSER |
| Парткод: | 302H025290 |
| Деталь: | SPONGE FUSER TL |
| Парткод: | 302H025300 |
| Деталь: | SPRING PRESSURE |
| Парткод: | 302H025310 |
| Деталь: | THERMOSTAT 190 FUSER |
| Парткод: | 302H025320 |
| Деталь: | WIRE FUSER PRIMARY |
| Парткод: | 302H046420 |
| Деталь: | WIRE FUSER PWB |
| Парткод: | 302H046460 |
| Деталь: | PARTS ROLLER HEAT SP |
| Парткод: | 302H094160 |
| Деталь: | PARTS HEATER FUSER 120 SP |
| Парткод: | 302H094180 |
| Деталь: | PARTS HEATER FUSER 230 SP |
| Парткод: | 302H094190 |
| Деталь: | PARTS HEATER FUSER 110 SP |
| Парткод: | 302H094550 |
| Деталь: | PARTS ROLLER PRESS SP |
| Парткод: | 302H094450 |
| Деталь: | SEPARATOR /40301P0028 A4 |
| Парткод: | 5MVX222XN002 |
| Деталь: | ACCESS.BAND |
| Парткод: | 7YZM420003++H01 |
| Деталь: | SPACER FUSER |
| Парткод: | 302H025210 |
| Деталь: | PLATE FUSER SPACER |
| Парткод: | 302H025220 |
| Деталь: | PIN SCREW BIND 3X6S |
| Парткод: | 303KZ02180 |
| Деталь: | PARTS FK-670(E) |
| Парткод: | 302H093040 |
| Деталь: | PARTS FK-670(U) |
| Парткод: | 302H093030 |
| Деталь: | PARTS FK-670(TW) |
| Парткод: | 302H093360 |
| Деталь: | CUSHION,CONTACT GLASS |
| Парткод: | 29812291 |
| Деталь: | BARRIER TABLET |
| Парткод: | 2BJ25240 |
| Деталь: | SPONGE LCD A |
| Парткод: | 2BJ25270 |
| Деталь: | SPONGE LCD B |
| Парткод: | 2BJ25280 |
| Деталь: | KEY MANAGEMENT |
| Парткод: | 2DA25290 |
| Деталь: | KEY OPERATION 10 |
| Парткод: | 2DA25350 |
| Деталь: | KEY FUNCTION J |
| Парткод: | 2FB24150 |
| Деталь: | KEY SAVER |
| Парткод: | 302DA25031 |
| Деталь: | KEY RESET |
| Парткод: | 302DC25071 |
| Деталь: | RETAINER LCD |
| Парткод: | 302FB24250 |
| Деталь: | KEY VOLUME |
| Парткод: | 302FB24470 |
| Деталь: | SHEET LCD |
| Парткод: | 302FB24860 |
| Деталь: | TABLET OPERATION |
| Парткод: | 302FB25190 |
| Деталь: | KEY INIT |
| Парткод: | 302FZ05020 |
| Деталь: | SPRING EARTH KEYTOP |
| Парткод: | 302FZ05190 |
| Деталь: | COVER OPE REAR |
| Парткод: | 302H005120 |
| Деталь: | LENS KEY B |
| Парткод: | 302H005310 |
| Деталь: | LCD OPERATION |
| Парткод: | 302JB45010 |
| Деталь: | WIRE PANEL UNIT |
| Парткод: | 302JB46020 |
| Деталь: | WIRE LCD |
| Парткод: | 302JB46050 |
| Деталь: | WIRE PANEL JUNCTION |
| Парткод: | 302JB46060 |
| Деталь: | WIRE PANEL RIGHT |
| Парткод: | 302JB46070 |
| Деталь: | PARTS,PWB OPERATION RIGHT ASSY SP |
| Парткод: | 302JB94030 |
| Деталь: | PARTS,PWB OPERATION TOP ASSY SP |
| Парткод: | 302JB94040 |
| Деталь: | PARTS,PWB OPERATION BOTTOM ASSY SP |
| Парткод: | 302JB94050 |
| Деталь: | COVER OPERATION |
| Парткод: | 302JC05012 |
| Деталь: | MOUNT LCD |
| Парткод: | 302JC05021 |
| Деталь: | KEY COPY |
| Парткод: | 302JC05040 |
| Деталь: | KEY PRINTER |
| Парткод: | 302JC05050 |
| Деталь: | KEY FAX |
| Парткод: | 302JC05060 |
| Деталь: | LENS LED |
| Парткод: | 302JC05070 |
| Деталь: | KEY PRINT |
| Парткод: | 302JC05080 |
| Деталь: | KEY STOP |
| Парткод: | 302JC05100 |
| Деталь: | LABEL START E |
| Парткод: | 302JC05180 |
| Деталь: | LABEL STOP E |
| Парткод: | 302JC05190 |
| Деталь: | LABEL RESET E |
| Парткод: | 302JC05200 |
| Деталь: | LABEL POWER E |
| Парткод: | 302JC05210 |
| Деталь: | LABEL FUNCTION E |
| Парткод: | 302JC05220 |
| Деталь: | LABEL SYSTEM MENU E |
| Парткод: | 302JC05230 |
| Деталь: | LABEL COPY E |
| Парткод: | 302JC05240 |
| Деталь: | FILM LCD A |
| Парткод: | 302JC05250 |
| Деталь: | FILM LCD B |
| Парткод: | 302JC05260 |
| Деталь: | FILM LCD C |
| Парткод: | 302JC05270 |
| Деталь: | FILM OPE PANEL |
| Парткод: | 302JC05280 |
| Деталь: | FILM MOUNT LCD |
| Парткод: | 302JC05300 |
| Деталь: | SHEET OPE SET B |
| Парткод: | 302JC05320 |
| Деталь: | SHEET OPE SET C |
| Парткод: | 302JC05330 |
| Деталь: | SHEET OPE SET D |
| Парткод: | 302JC05340 |
| Деталь: | SHEET OPE SET E |
| Парткод: | 302JC05350 |
| Деталь: | SHEET OPE SET F |
| Парткод: | 302JC05360 |
| Деталь: | SHEET OPE SET G |
| Парткод: | 302JC05370 |
| Деталь: | SHEET OPE SET H |
| Парткод: | 302JC05380 |
| Деталь: | SHEET OPE SET I |
| Парткод: | 302JC05390 |
| Деталь: | FILM KEY RIGHT |
| Парткод: | 302JC05400 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | THERMAL SHEET |
| Парткод: | 7ZS15096001+H01 |
| Деталь: | COVER BASE OPERATION |
| Парткод: | 302JC05031 |
| Деталь: | PLATE GROUND MOUNT OPE |
| Парткод: | 302H005370 |
| Деталь: | SPRING SHUTTER B |
| Парткод: | 2FT02140 |
| Деталь: | HANDLE OPE |
| Парткод: | 302GR05070 |
| Деталь: | CUSHION HANDLE A |
| Парткод: | 302GR05080 |
| Деталь: | BUSH PIN OPE |
| Парткод: | 302GR05090 |
| Деталь: | MOUNT SLIDE |
| Парткод: | 302GR05120 |
| Деталь: | BASE OPERATION |
| Парткод: | 302H005030 |
| Деталь: | MOUNT HANDLE OPE |
| Парткод: | 302H005041 |
| Деталь: | HINGE OPE LEFT |
| Парткод: | 302H005051 |
| Деталь: | HINGE OPE RIGHT |
| Парткод: | 302H005061 |
| Деталь: | SPRING HINGE OPE L |
| Парткод: | 302H005070 |
| Деталь: | SPRING HINGE OPE R |
| Парткод: | 302H005080 |
| Деталь: | MOUNT SLIDE LEFT |
| Парткод: | 302H005320 |
| Деталь: | BUSH SLIDE OPE |
| Парткод: | 302H005340 |
| Деталь: | PIN HINGE OPE |
| Парткод: | 302H005350 |
| Деталь: | PLATE GROUND BASE OPE |
| Парткод: | 302H005360 |
| Деталь: | PARTS OPERATION UNIT EXP |
| Парткод: | 302JC93022 |
| Деталь: | LEFT COVER MIDDLE |
| Парткод: | 302H004470 |
| Деталь: | COVER OZONE FILTER |
| Парткод: | 302H004620 |
| Деталь: | PLATE EARTH LEFT COVER |
| Парткод: | 302H004640 |
| Деталь: | JUNCTION PLATE HOOK |
| Парткод: | 302H004400 |
| Деталь: | MOUNT STRAP F |
| Парткод: | 302H004490 |
| Деталь: | MOUNT STRAP R |
| Парткод: | 302H004500 |
| Деталь: | SHAFT HOOK |
| Парткод: | 302H004410 |
| Деталь: | PLATE LEFT COVER MIDDLE |
| Парткод: | 302H004510 |
| Деталь: | HOOK LEFT COVER F |
| Парткод: | 302H004380 |
| Деталь: | HOOK LEFT COVER R |
| Парткод: | 302H004390 |
| Деталь: | PLATE LEFT COVER LOW |
| Парткод: | 302H004630 |
| Деталь: | PLATE EARTH LEFT COVER B |
| Парткод: | 302H004670 |
| Деталь: | SPRING LEFT HOOK |
| Парткод: | 2C904350 |
| Деталь: | GUIDE LEFT COVER |
| Парткод: | 302H004421 |
| Деталь: | GUIDE SEPARATE FEED |
| Парткод: | 302H028310 |
| Деталь: | REAR PLATE SEP |
| Парткод: | 302H028560 |
| Деталь: | SPRING SEPARATE FEED |
| Парткод: | 302H028370 |
| Деталь: | ARM SEPARATE FEED B |
| Парткод: | 302H028360 |
| Деталь: | COVER LEFT SEPARATE |
| Парткод: | 302H004610 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | ARM SEPARATE FEED A |
| Парткод: | 302H028350 |
| Деталь: | PLATE EXIT FEED |
| Парткод: | 302H028380 |
| Деталь: | GUIDE DU |
| Парткод: | 302H028340 |
| Деталь: | SHAFT SEP FEED |
| Парткод: | 302H028400 |
| Деталь: | PULLEY SEP FEED |
| Парткод: | 302H028320 |
| Деталь: | GUIDE EXIT LOWER |
| Парткод: | 302H028330 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SPRING EXIT FEED |
| Парткод: | 302H028410 |
| Деталь: | HOLDER SEP FEED |
| Парткод: | 302H028510 |
| Деталь: | SPRING GUIDE DU |
| Парткод: | 302H028390 |
| Деталь: | SHOULDER SCREW EXIT |
| Парткод: | 2C921400 |
| Деталь: | STRAP LEFT COVER |
| Парткод: | 302H004340 |
| Деталь: | MOUNT LEFT INTERLOCK SW |
| Парткод: | 302H004451 |
| Деталь: | SW.MICRO |
| Парткод: | 7SM010202+++H01 |
| Деталь: | ARM LEFT INTERLOCK SW |
| Парткод: | 302H004461 |
| Деталь: | SPRING LEFT INTERLOCK |
| Парткод: | 2C904340 |
| Деталь: | PIN LEFT COVER HOOK F |
| Парткод: | 302H004430 |
| Деталь: | FILTER OZONE A |
| Парткод: | 302H033170 |
| Деталь: | PIN SCREW BIND 3X6S |
| Парткод: | 303KZ02180 |
| Деталь: | PLATE GUIDE DU |
| Парткод: | 302H028590 |
| Деталь: | LABEL HIGH TEMP |
| Парткод: | 302H034130 |
| Деталь: | SPRING CONTACT DU |
| Парткод: | 302H024721 |
| Деталь: | LABEL VFEED CAUTION |
| Парткод: | 302FB05441 |
| Деталь: | DISPOSAL SENSOR ASSY |
| Парткод: | 2C901170 |
| Деталь: | GUIDE DRUM SHUTTER |
| Парткод: | 302H012010 |
| Деталь: | LEFT HOLDER SHEET |
| Парткод: | 302H012020 |
| Деталь: | RIGHT HOLDER SHEET |
| Парткод: | 302H012030 |
| Деталь: | SPRING DRUM SHUTTER |
| Парткод: | 302H012040 |
| Деталь: | STRAP DRUM SHUTTER |
| Парткод: | 302H012050 |
| Деталь: | FRONT ARM DRUM SHUTTER |
| Парткод: | 302H012060 |
| Деталь: | REAR ARM DRUM SHUTTER |
| Парткод: | 302H012070 |
| Деталь: | SHEET DRUM SHUTTER |
| Парткод: | 302H012080 |
| Деталь: | FRONT RAIL DRUM SHUTTER |
| Парткод: | 302H012090 |
| Деталь: | REAR RAIL DRUM SHUTTER |
| Парткод: | 302H012100 |
| Деталь: | FRONT RAIL LINK ARM |
| Парткод: | 302H012111 |
| Деталь: | REAR RAIL LINK ARM |
| Парткод: | 302H012120 |
| Деталь: | GUIDE STRAP |
| Парткод: | 302H012130 |
| Деталь: | HOLDER SENSOR |
| Парткод: | 302H012170 |
| Деталь: | DETECTION PLATE |
| Парткод: | 302H012180 |
| Деталь: | WIRE FRONT JUNCTION |
| Парткод: | 302H046570 |
| Деталь: | GUIDE WIRE FRONT |
| Парткод: | 302H004710 |
| Деталь: | SEAL WIRE A |
| Парткод: | 302H012330 |
| Деталь: | SPRING DETECTION |
| Парткод: | 2C918360 |
| Деталь: | WIRE,MAIN CHARGER |
| Парткод: | 2A068240 |
| Деталь: | GRID |
| Парткод: | 2FT10040 |
| Деталь: | SPRING WIRE /49585J0058 A4 |
| Парткод: | 5MMW141LX002 |
| Цена: | 80 ₽ |
| Деталь: | PIN CHARGER /A-49 CHARGER A4 |
| Парткод: | 5MVT263NN001 |
| Цена: | 160 ₽ |
| Деталь: | PARTS DISPOSAL TANK ASSY |
| Парткод: | 302H094540 |
| Деталь: | PARTS DK-670 |
| Парткод: | 302H093010 |
| Деталь: | PARTS MC-670 |
| Парткод: | 302H093310 |
Коды ошибок
C0030
C0060
C0070
C0100
C0110
C0120
C0130
C0140
C0150
C0160
C0170
C0180
C0210
C0240
C0280
C0320
C0420
C0440
C0610
C0630
C0800
C0820
C0830
C0860
C0870
C0880
C0890
C0920
C0960
C1010
C1020
C1030
C1040
C2000
C2200
C2500
C2600
C3100
C3200
C3300
C4000
C4010
C4200
C6000
C6020
C6050
C6120
C6150
C6400
C6420
C7000
C7200
C7300
C7400
C7410
C7800
C8030
C8140
C8170
C8180
C8190
C8210
C8440
C8460
C9000
C9060
F000
F010
F020
F030
F040
F041
F050
F060
F070
F080
F090
F14F
Описание
| Error code: | C0030 |
| Description: | FAX PWB system error |
| Causes: | The FAX processing cannot be continued due to the FAX firmware error. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. |
| Error code: | C0060 |
| Description: | Main PWB type mismatch error |
| Causes: | Poor contact in the connector terminals. |
| Remedy: | Check the connection of connector YC26 on the main PWB and relay board, and the continuity across the connector terminals. Repair if necessary. If the problem is not solved, run maintenance item U935 and return the relay board to the Service Administrative Division. |
| Error code: | C0070 |
| Description: | Toner motor |
| Causes: | Abnormal detection of FAX control PWB incompatibility in the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Remedy: | 1 Checking the FAX PWB The incompatible FAX PWB is installed. Install the FAX PWB for the applicable model. 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0100 |
| Description: | Charge corona winding problem |
| Causes: | An abnormal status is output from the flash memory. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. If not repaired, replace the main PWB. |
| Error code: | C0110 |
| Description: | Backup memory data problem (main PWB) • Data in the specified area of the backup memory does not match the specified values. |
| Causes: | Problem with the backup memory data. Defective main PWB. |
| Remedy: | Problem with the backup memory data. Run maintenance item U021 to set the contents of the backup memory data again. Defective main PWB. If the C0110 is displayed after initializing the backup memory, replace the main PWB and check for correct operation. |
| Error code: | C0120 |
| Description: | MAC address data error |
| Causes: | The MAC address data is incorrect. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the MAC address The MAC address is incorrect. Replace the main PWB when the MAC address is not indicated on the network status page. |
| Error code: | C0130 |
| Description: | Backup memory read / write error |
| Causes: | The reading or writing into the flash memory is unavailable. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reconnect the connectors on the main PWB. At that time, fix or replace the wires if they are pinched by other parts or have any damage. When the issue is not resolved, replace the main PWB. |
| Error code: | C0140 |
| Description: | Backup memory (EEPROM) data problem • Reading data from EEPROM is abnormal. |
| Causes: | Data damage of EEPROM. |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | C0150 |
| Description: | Engine EEPROM reading / writing error |
| Causes: | 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing data. 2. The data read reading in 2 points mismatches 8 times continuously. 3. The read data and the write data mismatch 8 times continuously. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0160 |
| Description: | Engine PWB EEPROM data error |
| Causes: | The data read from the EEPROM is judged as abnormal. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing U021 The storage data in the EEPROM on the engine PWB is faulty. Execute U021. Executing U021 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. |
| Error code: | C0170 |
| Description: | Charger count error |
| Causes: | The values in one of the billing counters, life counter or the scanner counter mismatch between the main side and the engine side. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. Detaching and reattaching the main PWB 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0180 |
| Description: | Machine serial number mismatch |
| Causes: | The machine serial Nos. in the main PWB and the EEPROM on the engine PWB mismatch when turning the power on. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. Executing U004 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0240 |
| Description: | Printer board* communication problem • The printer board does not respond 120 seconds after the power is turned on. |
| Causes: | Poor contact in the connector terminals. DIMM installed incorrectly. Defective main PWB or printer board. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC9 on the main PWB and YC5 on the printer board, and the continuity across the connector terminals. Repair or replace if necessary. DIMM installed incorrectly. Check the connection. Repair or replace if necessary. Defective main PWB or printer board. Replace the main PWB or printer board and check for correct operation. |
| Error code: | C0280 |
| Description: | Communication problem between the fax control PWB and main PWB Communication between the fax control PWB and the main PWB of the machine cannot be performed normally. |
| Causes: | Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective PWB. Replace the fax control PWB or main PWB and check for correct operation. |
| Error code: | C0320 |
| Description: | Power CPU communication problem A communication error is detected 10 times in succession. |
| Causes: | Defective engine PWB. |
| Remedy: | Replace the engine PWB and check for correct operation. |
| Error code: | C0420 |
| Description: | Side feeder* communication error • A communication error from side feeder is detected 10 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective side feeder main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC15 on the engine PWB and the connector YC3 on the side feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective side feeder main PWB. Replace the side feeder main PWB. |
| Error code: | C0440 |
| Description: | Document finisher communication problem • A communication error from document finisher is detected 10 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective finisher main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC14 on the engine PWB and YC4 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective finisher main PWB. Replace the finisher main PWB. |
| Error code: | C0610 |
| Description: | Lens drive problem |
| Causes: | Defective main PWB. |
| Remedy: | Replace the main PWB and check for correct operation. |
| Error code: | C0630 |
| Description: | DMA error |
| Causes: | DMA transmission of the image data does not finish within the certain time. |
| Remedy: | 1 Checking the connection 0 0 2 Checking the connection 0 0 3 Replacing the wire The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • DPCIS - DP relay PWB • DP relay PWB - Main PWB Wiring diagram 4 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. Detaching and reattaching the DP relay PWB 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0800 |
| Description: | Image processing error |
| Causes: | The print sequence jam (J010x) was detected 2 times continuously. |
| Remedy: | 1 Checking the image data The image data is faulty. When this issue occurs only when handling the certain image data, check if the image data is faulty. 2 Checking the situation The printing operation of the certain file is faulty. Acquire the jobs log if the phenomenon can be reproduced by specifying the job when the error was detected.` 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. Detaching and reattaching the main PWB 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0820 |
| Description: | Fax control PWB CG ROM checksum error (optional fax) A checksum error occurred with the CG ROM data of the fax control PWB. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0830 |
| Description: | FAX PWB flash program area checksum error |
| Causes: | The program stored in the flash memory on the FAX PWB is broken so it cannot perform. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 2 Checking the FAX PWB The FAX PWB is not properly connected. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0860 |
| Description: | Fax control PWB software switch checksum error (optional fax) A checksum error occurred with the software switch value of the fax control PWB. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0870 |
| Description: | PC FAX Image data transmission error |
| Causes: | Data was not properly transmitted even if the specified times of retry were made when the large volume data is transmitted between the FAX PWB and the main PWB. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 3 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 6 Executing U024 The data stored in the SSD is faulty. Execute U024 [SSD Format]. Executing U024 |
| Error code: | C0880 |
| Description: | Program archive problem (optional fax) When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0890 |
| Description: | Fax control PWB CG FONT archive problem (optional fax) When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0920 |
| Description: | 1st drawer lift |
| Causes: | The backup data could not be stored since the file system of the flash memory is faulty. |
| Remedy: | 1 Initializing the fax FAX control values are incorrect Execute U600 to initialize the FAX. Executing U600 2 Checking the FAX PWB The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Reinstalling the FAX PWB The FAX PWB is not properly installed. Reinstall the FAX PWB. FAX Installation Guide 4 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 5 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0960 |
| Description: | Developing unit EEPROM error • An error occurs in EEPROM data read or write for the developing unit. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective developing unit. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC5 on the engine PWB and the developing unit, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective developing unit. Replace the developing unit. |
| Error code: | C1010 |
| Description: | Lift motor 1 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 1 is installed. 2. The lock-up signal is not released for 1s after lift motor 1 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift motor 1 - Feed PWB Wiring diagram 4 Checking lift motor 1 Lift motor 1 is faulty. Check the operation of lift motor 1, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 1 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 1 is not properly attached or faulty. Reattach lift sensor 1. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1020 |
| Description: | Lift motor 2 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 2 is installed. 2. The lock-up signal is not released for 1s after lift motor 2 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Lift motor 2 - Feed PWB Wiring diagram 4 Checking lift motor 2 Lift motor 2 is faulty. Check the operation of lift motor 2, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 2 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 2 is not properly attached or faulty. Reattach lift sensor 2. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1030 |
| Description: | Lift motor 3 error • When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on. This error is detected four times successively. • During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 3. Defective lift motor 3. Poor contact of lift motor 3 connector terminals. Defective lift limit switch 3. Poor contact of lift limit switch 3 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 3. Replace lift motor 3. Defective lift motor 3. Check for continuity across the coil. If none, replace lift motor 3. Poor contact of lift motor 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 3. Run maintenance item U031 and turn lift limit switch 3 on and off manually. Replace lift limit switch 3 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB |
| Error code: | C1040 |
| Description: | Lift motor 4 error • When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on. This error is detected four times successively. • During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 4. Defective lift motor 4. Poor contact of lift motor 4 connector terminals. Defective lift limit switch 4. Poor contact of lift limit switch 4 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 4. Replace lift motor 4. Defective lift motor 4. Check for continuity across the coil. If none, replace lift motor 4. Poor contact of lift motor 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 4. Run maintenance item U031 and turn lift limit switch 4 on and off manually. Replace lift limit switch 4 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB. |
| Error code: | C2000 |
| Description: | Drive motor problem Stable OFF is detected for 1 s continuously after drive motor stability. The drive motor is not stabilized in 6 s since the motor is activated. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective drive motor. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective drive motor. Replace the drive motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | C2200 |
| Description: | Drive motor error • LOCK signal remains high for 1 s, 1 s after the drive motor has turned on. |
| Causes: | Poor contact in the drive motor connector terminals. Defective drive motor rotation control circuit. Defective drive transmission system. Defective deck PWB or engine PWB. |
| Remedy: | Poor contact in the drive motor connector terminals. Check the connection of connector YC2 and YC11 on the deck PWB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective drive motor rotation control circuit. Replace the drive motor. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective deck PWB or engine PWB. Replace the deck PWB or the engine PWB. |
| Error code: | C2500 |
| Description: | Feed motor error |
| Causes: | The ready signal is not at the L level after passing 2s since the feed motor drive was started. |
| Remedy: | 1 Checking the feed motor The operation of the feed motor is faulty. Execute U030 [Feed] to check the feed motor operation. Check if the drive gears rotate and have no excessive load, and apply the grease (EM-LP, Part no: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the feed motor The feed motor is faulty. Replace the feed motor. 4 Replacing the feed drive unit The feed drive unit is faulty. Replace feed drive unit. Detaching and reattaching the Feed Drive Unit 5 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 6 Firmware upgrade The firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB 8 Replacing the feed image PWB The power can`t be supplied to the feed drive PWB. Replace the feed image PWB. |
| Error code: | C2600 |
| Description: | PF feed motor error |
| Causes: | The ready signal is not at the L level (stable rotation) after passing 1s since the PF feed motor drive started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected, or it is faulty. Execute U247 [2PF] or [LCF] > [Motor On] to check the paper feed operation. If the PF feed motor does not operate properly, reconnect the connector of the motor. Check if the PF feed roller and the drive gears rotate smoothly and have no excessive load, apply the grease (EM-50LP, Part no.: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF PWB • PF PWB - Engine PWB (Drawer connector between the paper feeder and the main unit) Service Manual - Section 8 `PWBs` 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF Drive Unit 4 Firmware upgrade The engine firmware or the PF firmware is faulty. Upgrade the engine firmware and the PF firmware to the latest version. Firmware Update 5 Replacing the PF PWB The PF PWB is faulty. Replace the PF PWB. Detaching and reattaching the PF PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C3100 |
| Description: | Carriage error |
| Causes: | When turning the power on or finishing originals scan through the scanner, the alignment of the home position sensor (turning on / off the sensor) fails and the error is detected. Then, the error is detected twice continuously even the initial operation is executed. |
| Remedy: | 1 Unlocking the scanner mirror frame The scanner mirror frame is not unlocked. Unlock the scanner mirror frame (lamp unit assy). Unlocking the scanner mirror frame 2 Checking the scanner movement A load is applied to the scanner movement. Check the operation of the lamp by U073 or manually moving it. If there is an excess load, check if there are any foreign objects on the optical wire or optical wire drum and clean it. After that, apply grease on the scanner rail. Detaching and reattaching the scanner wires 3 Checking the scanner wires The scanner wires are dirty or come off. Clean and reattach the scanner wires. Detaching and reattaching the scanner wires 4 Checking the scanner motor The scanner motor is faulty. Reattach the scanner motor and reconnect the connector. If not repaired, replace it. 5 Checking the belt tension of the scanner motor A load is applied to the scanner movement since the belt tension is improper. Adjust the scanner motor belt tension properly. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Scanner motor - Engine PWB Wiring diagram 7 Checking the home position sensor The home position sensor is not properly attached. Reattach the home position sensor. 8 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Home position sensor - Engine PWB Wiring diagram 9 Replacing the home position sensor The home position sensor is faulty. Replace the home position sensor. 10 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3200 |
| Description: | LED lamp startup error |
| Causes: | The white reference data acquired by lighting the LED lamp at the initial operation does not reach the specified value. Or, the light amount detected by the CCD PWB is not enough. (2 or more LED lamps do not light. The light does not reach the CCD PWB due to condensation.) |
| Remedy: | 1 Checking the LED lamp The LED lamp does not light. Execute U061 [CCD] and check if the LED lamp is lit. If not, replace the lamp unit. After that, execute U411 [Table(ChartA)]. Detaching and reattaching the lamp unit 2 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB • LED PWB - CCD PWB Wiring diagram 3 Checking the mirror The mirror or lens is frosted due to condensation. Clean the mirrors. If the condensation at the scanner section is resolved naturally by opening the document processor or the platen cover, turn the power switch off and on. 4 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3300 |
| Description: | CCD AGC error (For the internal count) |
| Causes: | Brightness of the LED lamp is darker while one of the LED lamp does not turn on or brighter than expected when processing the AGC for the CCD lamp. |
| Remedy: | 1 Checking the LED lamp The LED lamp is faulty. Check if the LED lamp lights by executing U061 [CCD]. If it does not light, replace the lamp unit and execute U411 [Table (ChartA) ]. Detaching and reattaching the lamp unit 2 Cleaning the backside of the contact glass The white reference sheet is dirty. Clean the white reference sheet at the backside of the contact glass. Detaching and reattaching the contact glass 3 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is peeled off, deformed or the FFC is broken, replace the FFC. • LED PWB - CCD PWB • CCD PWB - Engine PWB Wiring diagram 4 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 5 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4000 |
| Description: | Polygon motor synchronization problem • The revolution does not reach the stable speed within 20 s of the START signal. |
| Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
| Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
| Error code: | C4010 |
| Description: | Polygon motor steady-state problem • The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized. |
| Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
| Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
| Error code: | C4200 |
| Description: | BD steady-state problem • ASIC of the main PWB detects a BD error A for 4000 ms after the polygon motor rotation has been stabilized. |
| Causes: | Defective laser diode. Defective polygon motor. Defective main PWB. Poor contact in connector terminals. |
| Remedy: | Defective laser diode. Replace the laser scanner unit. Defective polygon motor. Replace the laser scanner unit. Defective main PWB. Replace the main PWB and check for correct operation. Poor contact in connector terminals. Check the connection of connector YC8 on the main PWB and the continuity across the connector terminals. Repair or replace if necessary. |
| Error code: | C6000 |
| Description: | IH heating error 1 |
| Causes: | The fuser center thermistor temperature does not reach 100°C / 212°F when passing 60s since warm-up starts. Or, the ready display temperature is not detected when passing 420s since the fuser center thermistor temperature reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Executing U169 The IH setting mismatches the power source specification. Set the fuser destination same as the IH PWB voltage at U169. Executing U169 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature cannot be detected properly due to the broken thermostat or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6020 |
| Description: | Fuser center thermistor high temperature error |
| Causes: | The fuser center thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6050 |
| Description: | Fuser center thermistor low temperature error |
| Causes: | The fuser center thermistor detects less than 100°C / 212°F for 1s after warm-up, or during print or standby. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 11 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit |
| Error code: | C6120 |
| Description: | Fuser press thermistor high temperature error |
| Causes: | The fuser press thermistor detects 210°C / 410°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6150 |
| Description: | Fuser press thermistor low temperature error |
| Causes: | The fuser press thermistor detects less than 30°C / 86°F for 1s after warm-up. |
| Remedy: | 1 Removing foreign material There are foreign objects between the fuser press thermistor and the press roller. Or, the foreign objects are adhered on the press roller. Remove foreign objects if any on the press roller. Then, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 9 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB 10 Replacing the IH unit The IH unit is faulty. Replace the IH unit. |
| Error code: | C6400 |
| Description: | Zero-cross signal error • The engine PWB does not detect the zero-crossing signal (Z CROSS SIG) for 5 s. |
| Causes: | Poor contact in the connector terminals. Defective DC power source PWB. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and YC6 on the DC power source PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective DC power source PWB. Check if the zero-crossing signal is output from YC6-3 on the DC power source PWB. If not, replace the DC power source PCB. Defective engine PWB. Replace the engine PWB if C6400 is detected while YC6-3 on the DC power source PWB outputs the zero-crossing signal. |
| Error code: | C6420 |
| Description: | Fuser unit fuse cut problem The fuse cannot be cut, When replacing the fuser unit, the fuse cannot be cut in 3 s after the fuse cut signal is turned on. |
| Causes: | Poor contact in the connector terminals. Fuser unit connector inserted incorrectly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC1 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. |
| Error code: | C7000 |
| Description: | Toner motor problem After driving of the toner motor starts, the error signal is not at the H level for 500 ms continuously. |
| Causes: | Poor contact in the connector terminals. Broken the gear Defective toner motor M/C/Y/K. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC26 on the engine PWB and the connector of the toner motor, and the continuity across the connector terminals. Repair or replace if necessary. Broken the gear. Check visually and replace the gear if necessary. Defective toner motor M/C/Y/K. Run maintenance item U135 and check if the toner motor operates. If not, replace the toner motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | C7200 |
| Description: | Internal thermistor broken (For the internal count) |
| Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) exceeds the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
| Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7300 |
| Description: | Toner hopper problem • During toner replenishment after toner empty has been detected, toner empty could not be cleared in 3 times of 360 s. |
| Causes: | Defective toner level detection sensor. Poor contact in the toner level detection sensor connector terminals. |
| Remedy: | Defective toner level detection sensor. Replace the toner level detection sensor. Poor contact in the toner level detection sensor connector terminals. Check the connection of connectors YC2 and YC5 on the deck PWB and YC3 on the engine PWB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Error code: | C7400 |
| Description: | Developing unit connector insertion problem Absence of the developing unit is detected. |
| Causes: | Developing unit connector inserted incorrectly. Defective developing unit connector. |
| Remedy: | Developing unit connector inserted incorrectly. Reinsert the developing unit connector if necessary. Defective developing unit connector. Replace the developing unit. |
| Error code: | C7410 |
| Description: | Drum unit connector insertion problem Absence of the drum unit is detected. |
| Causes: | Drum unit connector inserted incorrectly. Defective drum unit connector. |
| Remedy: | Drum unit connector inserted incorrectly. Reinsert the drum unit connector if necessary. Defective drum unit connector. Replace the drum unit. |
| Error code: | C7800 |
| Description: | Outer thermistor broken (For the internal count) |
| Causes: | The external temperature sensor (external thermistor) cannot be accessed. No response is received from the external thermistor 5 times continuously for 5ms or more when accessing the external thermistor. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Room temperature sensor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Replacing the external temperature sensor The external temperature sensor is faulty. Replace the external temperature sensor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C8030 |
| Description: | Punch motor error 3 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position detection does not turn off within 50ms when initializing the home position. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8140 |
| Description: | Main tray error 1 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 does not turn on when passing 30s while lifting up the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8170 |
| Description: | DF side registration motor 1 error 1 Object: 4000-sheet finisher |
| Causes: | The home position cannot be detected after passing 3s when relocating to the home position. |
| Remedy: | 1 Checking the front DF side registration guide The front DF side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. 5 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8180 |
| Description: | DF side registration motor 1 error 2 Object: 4000-sheet finisher |
| Causes: | J6810/J6811/J6812 (Front DF side registration jam) was detected 2 times continuously. |
| Remedy: | 1 Checking the front DF side registration guide The front side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive components. 3 Replacing the front DF side registration guide drive components The front DF side registration guide drive components are faulty. Replace the front DF side registration guide drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB 5 Checking DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. Executing U240 6 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8190 |
| Description: | DF side registration motor 2 error 1 Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while executing the operation of returning to the home position. |
| Remedy: | 1 Checking the rear DF side registration guide The rear DF side registration guide is not assembled properly. If the rear DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear DF side registration guide drive components The rear DF side registration guide drive parts are not properly attached or faulty. Reattach the rear DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 2 - DF main PWB • DF side registration sensor 2 - DF main PWB 4 Replacing DF side registration motor 2 DF side registration motor 2 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking DF side registration sensor 2 DF side registration sensor 2 is not properly attached or faulty. Reattach DF side registration sensor 2 and execute U241 [Finisher] > [Width Tail HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8210 |
| Description: | DF staple motor front/rear error Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while returning to the home position at the initial operation. |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple unit is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the DF staple unit drive components The DF staple unit drive parts are not properly attached or faulty. Reattach the DF staple unit drive parts. If not repaired, replace the parts. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple motor - DF main PWB • DF staple sensor - DF main PWB Wiring diagram 4 Replacing the DF staple motor The DF staple motor is faulty. Execute U240 [Motor] > [Staple]. If the DF staple motor does not properly operate, replace the DF staple unit. 5 Checking the DF staple sensor The DF staple sensor is not properly attached or faulty. Reattach the DF staple sensor. Then, replace the DF staple unit if the sensor is not fixed. Detaching and reattaching the DF staple unit 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8440 |
| Description: | Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range. |
| Causes: | The paper entry sensor connector makes poor contact. Defective paper entry sensor. The optical path of the paper entry sensor is blocked by foreign matter. Defective finisher main PWB. |
| Remedy: | The paper entry sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective paper entry sensor. Replace the paper entry sensor and check for correct operation. The optical path of the paper entry sensor is blocked by foreign matter. Remove the foreign matter. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8460 |
| Description: | EEPROM problem (optional document finisher) Reading from or writing to EEPROM cannot be performed. |
| Causes: | Defective EEPROM or finisher main PWB. |
| Remedy: | Replace the finisher main PWB and check for correct operation. |
| Error code: | C9000 |
| Description: | Main program error (DP) / Document Processor communication error |
| Causes: | The document processor cannot be communicated. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware and the DP firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DP main PWB - Engine PWB Wiring diagram 3 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. Detaching and reattaching the DP main PWB 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C9060 |
| Description: | DP EEPROM error |
| Causes: | Read data and write data to the EEPROM do not match 3 times continuously. |
| Remedy: | 1 Checking the EEPROM The EEPROM is not properly installed. Reattach the EEPROM on the DP main PWB. 2 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. Detaching and reattaching the DP main PWB 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the DP main PWB and execute U411. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F030 |
| Description: | Main PWB system error |
| Causes: | Defective main PWB. |
| Remedy: | Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F041 |
| Description: | Over than available setting number tray detection error |
| Causes: | Over than available setting number tray is installed. |
| Remedy: | Remove the available setting number tray. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F060 |
| Description: | Engine RAM error |
| Causes: | Defective engine PWB. |
| Remedy: | Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | F070 |
| Description: | Communication error between System-CPU and Engine-CPU |
| Causes: | Switching regulator • Replace the fuse (F210). • Replace the switching regulator. LGC board SYS board If the problem is not corrected with the replacement of the LGC board, reinstall the removed LGC board and replace the SYS board. IMG board If the problem is still not corrected with the replacement of the SYS board, reinstall the removed SYS board and replace the IMG board. |
| Remedy: | (1) Check if the connector CN104 on the SYS board and CN130, CN131, CN134 on the SYSIF board is disconnected. (2) Check if the connector CN10 on the SLG board is disconnected. (3) Check if the harness connecting the SYSIF board and SLG board is disconnected or open circuited. (4) Check if the harness connecting the SYSIF board and LGC board is disconnected or open circuited. (5) Check if the connection of the SYS board (CN104) and SYSIF board (CN130) is open circuited. (6) If the SYS board has been replaced, check if the jumper pin setting on the SYS board is correct. (The jumper pin should be inserted between pin 2 and 3 of CN103 and CN115.) (7) Check the version of the system ROM on the SYS board. (8) Check the version of the engine ROM version on the LGC board. (9) Check the version of the scanner ROM version on the SLG board. (10) Replace the SYS board. (11) Replace the SLG board. (12) Replace the LGC board. (13) Replace the SYSIF board. |
| Error code: | F080 |
| Description: | Flash ROM error (during download) |
| Causes: | Defective flash ROM. |
| Remedy: | Defective flash ROM. Replace the engine PWB and check for correct operation. |
| Error code: | F090 |
| Description: | SRAM abnormality on SYS board |
| Causes: | SRAM (SYS board) |
| Remedy: | (1) Turn the power OFF and start up the Setting Mode (08). (2) When “SRAM ERROR DOES IT INITIALIZE” is displayed on the LCD, check the destination and then press the [START] button. If the destination is not correct, key in the correct one and then press the [START] button. (3) After the confirmation message is displayed on the LCD, press the [INTERRUPT] button (to initialize the SRAM). (4) Perform the panel calibration (08-692). (5) Perform the initialization at the software version upgrade (08-947). (6) Enter the serial number (08-995). Be sure that the serial number is the same as that on the identification label attached on the rear cover of the equipment. Note: The MAC address of the equipment is generated based on this serial number. Entering the incorrect serial number may result in an inability to access the network due to an invalid MAC address. (7) Initialize the NIC information (08-693). (8) Turn the power OFF and then start up with the Adjustment mode (05). (9) Turn the power OFF and then back ON. If the error is not recovered, replace the SRAM on the SYS board. |
| Error code: | F14F |
| Description: | Power source PWB secondary side error |
| Causes: | Defective power source PWB. |
| Remedy: | Defective power source PWB. Replace the power source PWB and check for correct operation. |
