Kyocera KM-4050
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
120000
Скорость печати
A4
40
Цветность печати
черно-белая
Общие характеристики |
|
|---|---|
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Тип устройства |
МФУ |
Цветность печати |
|
Макс. формат |
A3 |
Область применения |
большой офис |
Число страниц в месяц |
120 000 |
Сканер |
|
Копир |
|
Размещение |
настольный |
Факс |
|
Телефон |
|
Печать фотографий |
|
Принтер |
|
Пигментные чернила |
|
Печать без полей |
|
Прямая печать |
|
Время разогрева |
30 |
Двусторонняя печать |
|
Макс, разрешение для ч/б печати |
|
| По Y | 600 |
| По X | 2 400 |
Скорость ч/б печати |
|
| A4 | 40 |
| A3 | 23 |
Время выхода первого отпечатка |
|
| Ч/б | 3,9 |
Копир |
|
Время выхода первой копии |
3,9 |
Макс, количество копий за цикл |
999 |
Шаг масштабирования |
0,01 |
Значение масштаба |
|
| Максимальное | 4 |
| Минимальное | 0,25 |
Макс, разрешение (ч/б) |
|
| По Y | 600 |
| По X | 600 |
Сканер |
|
Стандарт TWAIN |
|
Отправка изображения по e-mail |
|
Устройство автоподачи оригиналов |
одностороннее |
Макс. формат оригинала |
A3 |
Оттенки серого |
256 |
Тип сканера |
планшетный/протяжный |
Макс, размер сканирования |
|
| По Y | 420 |
| По X | 297 |
Разрешение сканера |
|
| По Х | 600 |
Скорость сканирования |
|
| Цветн, | 25 |
| Ч/б | 50 |
Расходные материалы |
|
Количество картриджей |
1 |
Печать на: |
|
| Конвертах |
|
| Карточках |
|
| Матовой бумаге |
|
| Этикетках |
|
| Пленках |
|
| Глянцевой бумаге |
|
| Рулоне |
|
| Фотобумаге |
|
| CD/DVD |
|
Плотность бумаги |
|
| Минимальная | 45 |
| Максимальная | 200 |
Факс |
|
Цветной |
|
Телефон |
|
Стандарт DECT |
|
АОН |
|
Проводная трубка |
|
Беспроводная трубка |
|
Caller ID |
|
Автоответчик |
|
Спикерфон |
|
Шрифты и языки управления |
|
Языки управления |
|
| PCL 5e |
|
|
|
|
| PostScript 2 |
|
| PPDS |
|
| PCL 5c |
|
| PCL 6 |
|
| PostScript 3 |
|
| PostScript |
|
Количество установленных шрифтов |
|
| PCL | 80 |
Лотки |
|
Подача бумаги |
|
| Стандартная | 1 200 |
| Максимальная | 4 200 |
Вывод бумаги |
|
| Стандартный | 250 |
Финишер |
|
Степлер |
|
Сортировка со сдвигом |
|
Брошюровщик |
|
Сортер |
|
Электронная сортировка |
|
Интерфейсы |
|
LPT |
|
USB |
|
Ethernet (RJ-45) |
|
Веб-интерфейс |
|
Bluetooth |
|
Wi-Fi |
|
Устройство для чтения карт памяти |
|
RS-232 |
|
FireWire (IEEE 1394) |
|
Инфракрасный порт |
|
Количество свободных слотов расширения |
2 |
Версия USB |
2,0 |
Память/Процессор |
|
Объем памяти |
512 |
Частота процессора |
600 |
Макс, объем памяти |
1 024 |
Процессор |
PowerPC 750FL |
Емкость жесткого диска |
40 |
Дополнительная информация |
|
Экран |
|
Поддержка ОС |
|
| Mac OS |
|
| Linux |
|
| DOS |
|
| Windows |
|
Потребляемая мощность |
|
| При работе | 1 010 |
| В режиме ожидания | 230 |
Уровень шума |
|
| В режиме ожидания | 52 |
| При работе | 69 |
Габариты |
|
Вес |
85 |
Высота |
745 |
Глубина |
646 |
Ширина |
599 |
Модули
FRAME L
Electrical Components I
Option II (DT-700 and Key Counter)
Paper Conveying
Scanner Unit II
CASSETTE
Paper Feed-In III
Drive Unit II
PANEL
Paper Exit (110V)
LSU
Drum Unit
Operation Unit (110V)
Scanner Unit I
CASSETTE ASSEMBLY
Bypass feed unit
Electrical Components II
PAPER FEED
Operation Unit (120/230/240V)
Drive Unit I
COVERS and LABELS
Bypass unit
FUSER UNIT
Paper Exit (120/230/240V)
Paper Feed-In I
COVERS
Paper Feed-In II
Developer unit
Option I (Original Holder) and Accessories
ADF 1
FRAMES
DUPLEX
Детали COVERS
| Деталь: | PANEL UNIT, MFC9840CDW |
| Парткод: | FK-715 |
| Цена: | 31 000 ₽ |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | 2BM27890 |
| Деталь: | LABEL ELE SHOCK CAUTION |
| Парткод: | 302GR34310 |
| Деталь: | COVER CONN |
| Парткод: | 302GR39190 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | WIRE BYPASS FEED PI |
| Парткод: | 302GR46300 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H02 |
| Деталь: | RETAINING PIN,DRAWER |
| Парткод: | 3033927451 |
| Деталь: | MOUNT DRUM DRAWER |
| Парткод: | 2BL26200 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC10B1112+H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510009++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | WIRE PAPER FEED(C) |
| Парткод: | 302GR46120 |
| Деталь: | MOUNT,CASSETTE SWITCH |
| Парткод: | 302FG07050 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | CLAMP,CKN-10(KITAGAWA) |
| Парткод: | M2105970 |
| Деталь: | MOUNT POWER PWB |
| Парткод: | 302GR39081 |
| Деталь: | LVU 100 |
| Парткод: | 302GR45011 |
| Деталь: | LVU 200 |
| Парткод: | 302GR45021 |
| Деталь: | SHIELD SUBWIRE |
| Парткод: | 2BJ26210 |
| Деталь: | MOUNT OPTION I/F |
| Парткод: | 302GR39090 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | WIRE FINISHER SOCKET |
| Парткод: | 302GR46160 |
| Деталь: | LID VENDOR |
| Парткод: | 302FB26290 |
| Деталь: | EDGING, EDS-17L(KITAGAWA) |
| Парткод: | M2104250 |
| Деталь: | WIRE OPTION(C) |
| Парткод: | 302GR46350 |
| Деталь: | MOUNT, DECK CONNECTOR |
| Парткод: | 2AR26340 |
| Деталь: | SW SEESAW |
| Парткод: | 7SC010101+++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | EDGING, EDS-25L(KITAGAWA) |
| Парткод: | M2104280 |
| Деталь: | MOUNT FIXING DRAWER |
| Парткод: | 2BL26290 |
| Деталь: | WIRE DRAWER |
| Парткод: | 302GR46190 |
| Деталь: | WIRE PRIMARY(C) |
| Парткод: | 302GR46360 |
| Деталь: | PIN TERMINAL |
| Парткод: | 302BL26061 |
| Деталь: | SPRING TERMINAL |
| Парткод: | 2BL26070 |
| Деталь: | SPRING TERMINAL T |
| Парткод: | 2BL26270 |
| Деталь: | CASE HIGH VOLTAGE |
| Парткод: | 302BL26051 |
| Деталь: | GROUND PLATE HV |
| Парткод: | 2BL26080 |
| Деталь: | HVU |
| Парткод: | 302GR45031 |
| Деталь: | WIRE HIGH VOLTAGE(C) |
| Парткод: | 302GR46130 |
| Деталь: | WIRE MOTOR(C) |
| Парткод: | 302GR46340 |
| Деталь: | WIRE FRONT(C) |
| Парткод: | 302GR46110 |
| Деталь: | EDGING,EDS-2 |
| Парткод: | M2104210 |
| Деталь: | LEFT MOUNT I/L |
| Парткод: | 2BL26110 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | SWITCH,INTERLOCK |
| Парткод: | 2AR27040 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | LEFT WORK PLATE I/L |
| Парткод: | 2BL26120 |
| Деталь: | SHAFT I/L |
| Парткод: | 302BL26281 |
| Деталь: | WIRE SADDLE,YMC-15-0(KITAGAWA) |
| Парткод: | M2109350 |
| Деталь: | FRONT MOUNT COVER |
| Парткод: | 2BL04060 |
| Деталь: | INNER LEFT COVER |
| Парткод: | 302GR04330 |
| Деталь: | TONER DETECTION ASSY |
| Парткод: | 302GR01190 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC05B1106+H01 |
| Деталь: | WIRE TONER DISPOSAL |
| Парткод: | 302GR46290 |
| Деталь: | SPACER WIRE |
| Парткод: | 2BL04460 |
| Деталь: | GROUND PLATE INNER L |
| Парткод: | 2BL04450 |
| Деталь: | MOUNT INLET A |
| Парткод: | 302FG26102 |
| Деталь: | MOUNT PWB FILTER |
| Парткод: | 302GR39141 |
| Деталь: | INLET ASSY |
| Парткод: | 302GR01240 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBCP8P8E001H01 |
| Деталь: | UNIT FILTER |
| Парткод: | 302GR45090 |
| Деталь: | UNIT FILTER 200 |
| Парткод: | 302GR45100 |
| Деталь: | WIRE FILTER-LVU |
| Парткод: | 302GR46650 |
| Деталь: | MOUNT MAIN SW |
| Парткод: | 302GR39120 |
| Деталь: | FAN LVU 42-10 |
| Парткод: | 302GR44260 |
| Деталь: | WIRE LVU FAN |
| Парткод: | 302GR46750 |
| Деталь: | POWER CORD 110 |
| Парткод: | 3065027601 |
| Деталь: | POWER CORD(120) |
| Парткод: | 3019527401 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | POWER CODE AS(240) |
| Парткод: | 3029927232 |
| Деталь: | LOWER WING TRAY |
| Парткод: | 2BJ60530 |
| Деталь: | UPPER WING TRAY |
| Парткод: | 302BJ60521 |
| Деталь: | RAIL WING TRAY |
| Парткод: | 302BJ60541 |
| Деталь: | MOUNT WING TRAY |
| Парткод: | 302GR04490 |
| Деталь: | HOLDER WING TRAY |
| Парткод: | 302GR04500 |
| Деталь: | SOCKET ASSY,KEY COUNTER |
| Парткод: | 3029236241 |
| Деталь: | COVER,KEY COUNTER |
| Парткод: | 302A360011 |
| Деталь: | RETAINER,KEY COUNTER COVER |
| Парткод: | 3066060023 |
| Деталь: | RETAINER,KEY COUNTER |
| Парткод: | 3066060031 |
| Деталь: | MOUNT,KEY COUNTER |
| Парткод: | 3066060041 |
| Деталь: | KEY COUNTER |
| Парткод: | 82142540 |
| Деталь: | SET PARTS KEYCOUNTER NEW COLOR |
| Парткод: | 302A369707 |
| Деталь: | GEAR 25 |
| Парткод: | 2AL06110 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | ROLLER DU FEED UP |
| Парткод: | 2BL07020 |
| Деталь: | ROLLER DU FEED LOW |
| Парткод: | 2BL07030 |
| Деталь: | PULLEY DU |
| Парткод: | 2BL07040 |
| Деталь: | SPRING DU PULLEY |
| Парткод: | 2BL07060 |
| Деталь: | SPRING DU JOINT |
| Парткод: | 2BL07080 |
| Деталь: | ACTUATOR DU |
| Парткод: | 2BL07090 |
| Деталь: | PLATE EARTH DU |
| Парткод: | 2BL07110 |
| Деталь: | PLATE NUT DU |
| Парткод: | 2BL07120 |
| Деталь: | SPRING DU ACT. |
| Парткод: | 2BL07130 |
| Деталь: | FILM WIRE DU |
| Парткод: | 2BL07140 |
| Деталь: | GUIDE RIB DU |
| Парткод: | 2BL07150 |
| Деталь: | UNDER CLEANER REGIST |
| Парткод: | 2BL07950 |
| Цена: | 1 500 ₽ |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL16080 |
| Деталь: | STRAP CONVEYING A |
| Парткод: | 2BL16100 |
| Деталь: | STRAP CONVEYING B |
| Парткод: | 2BL16110 |
| Деталь: | GUIDE REGIST F |
| Парткод: | 2BL16130 |
| Цена: | 330 ₽ |
| Деталь: | PLATE TRANS B |
| Парткод: | 2BL16150 |
| Деталь: | PLATE TRANS UNIT GND |
| Парткод: | 2BL16160 |
| Деталь: | PLATE SEPARATION B |
| Парткод: | 2BL16170 |
| Деталь: | HOOK CONVEYING |
| Парткод: | 2BL16190 |
| Деталь: | SPRING CONVEYING |
| Парткод: | 2BL16200 |
| Деталь: | GUIDE FEED F |
| Парткод: | 2BL16250 |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | PULLEY EXIT T30 |
| Парткод: | 2BL21230 |
| Деталь: | BELT EXIT P2M212 |
| Парткод: | 2BL21240 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | PLATE MID FEED UNIT |
| Парткод: | 2FG16010 |
| Деталь: | SPACER REGIST |
| Парткод: | 2FG16250 |
| Деталь: | GUIDE FEED |
| Парткод: | 2FG16290 |
| Деталь: | SPRING REGIST F |
| Парткод: | 2FG16300 |
| Деталь: | SPRING REGIST R |
| Парткод: | 2FG16310 |
| Деталь: | SPRING FEED |
| Парткод: | 2FG16320 |
| Деталь: | HOLDER SHAFT |
| Парткод: | 2FG16330 |
| Деталь: | SHAFT DU PULLEY |
| Парткод: | 302BL07052 |
| Деталь: | JOINT DU |
| Парткод: | 302BL07071 |
| Деталь: | SHAFT CONVEYING |
| Парткод: | 302BL16211 |
| Деталь: | SPRING CONVEYING B |
| Парткод: | 302BL16241 |
| Деталь: | BASE CONVEYING A |
| Парткод: | 302FG16263 |
| Деталь: | SHEET CONVEYING |
| Парткод: | 302FG16272 |
| Деталь: | SHAFT FEED |
| Парткод: | 302FG16281 |
| Деталь: | HANDLE CONVEYING |
| Парткод: | 302GR24010 |
| Деталь: | PLATE PAPER GUIDE |
| Парткод: | 302GR24020 |
| Деталь: | MOUNT CONVEYING FAN |
| Парткод: | 302GR24030 |
| Деталь: | FILM COVER WIRE |
| Парткод: | 302GR24040 |
| Деталь: | FRAME DU |
| Парткод: | 302GR29010 |
| Деталь: | CLUTCH FEED |
| Парткод: | 302GR44120 |
| Деталь: | FAN CONVEYING 42-10 |
| Парткод: | 302GR44250 |
| Деталь: | WIRE DUPLEX |
| Парткод: | 302GR46421 |
| Деталь: | WIRE CONVEYING FAN |
| Парткод: | 302GR46730 |
| Деталь: | HOUSING TRANSFER |
| Парткод: | 2BL17010 |
| Деталь: | PULLEY TRANS ROLLER |
| Парткод: | 2BL17040 |
| Деталь: | PLATE TRANS UNIT |
| Парткод: | 2BL17050 |
| Деталь: | GEAR TRANS Z25H |
| Парткод: | 2BL17090 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BL17170 |
| Деталь: | HOLDER SEPARATION A |
| Парткод: | 2FG17010 |
| Деталь: | SPRING TRANS R |
| Парткод: | 2FG17160 |
| Деталь: | BUSH TRANS ROLLER |
| Парткод: | 302BL17061 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 302GR22010 |
| Деталь: | BRUSH SEPARATION |
| Парткод: | 302GR22020 |
| Деталь: | SPACER SEPARATION |
| Парткод: | 302GR22030 |
| Деталь: | SPRING TRANSFER F |
| Парткод: | 302GR22050 |
| Деталь: | COLLAR TRANS ROLLER |
| Парткод: | 302GR22110 |
| Деталь: | BUSHING,CLEANING BLADE SHAFT |
| Парткод: | 75718040 |
| Деталь: | CUT WASHER 10 |
| Парткод: | 2BL07970 |
| Деталь: | STOPPER BUSH |
| Парткод: | 2BL16030 |
| Деталь: | GEAR REGIST Z18 |
| Парткод: | 2BL16060 |
| Деталь: | BUSHING REGIST |
| Парткод: | 2BL16260 |
| Деталь: | ROLLER REGIST |
| Парткод: | 2FG16021 |
| Деталь: | PULLEY REGIST |
| Парткод: | 2FG16030 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR 20,IDLE |
| Парткод: | 66506630 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC02B1001+H01 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | BINDING BAND,T18R |
| Парткод: | M2307010 |
| Деталь: | GUIDE ROLLER F |
| Парткод: | 2FG16160 |
| Деталь: | GUIDE ROLLER R |
| Парткод: | 2FG16170 |
| Деталь: | FE-710 |
| Парткод: | 302GR93141 |
| Деталь: | TR-710 |
| Парткод: | 302GR93281 |
| Деталь: | PARTS,ROLLER REGIST SET |
| Парткод: | 302GR93340 |
| Деталь: | PARTS CONTACT GLASS (M) ASSY |
| Парткод: | 302GR93310 |
| Деталь: | PARTS CONTACT GLASS (I) ASSY |
| Парткод: | 302GR93320 |
| Деталь: | PARTS CONTACT GLASS DP ASSY |
| Парткод: | 302GR94380 |
| Деталь: | SPACER CONTACT GLASS DP |
| Парткод: | 302GR17950 |
| Деталь: | CUSHION,CONTACT GLASS |
| Парткод: | 29812291 |
| Деталь: | ACCESS.BUSHING |
| Парткод: | 7YZM110004++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PLATE HOLDER ISU |
| Парткод: | 302GR17670 |
| Деталь: | PLATE SPRING ISU |
| Парткод: | 302GR17680 |
| Деталь: | PARTS ISU |
| Парткод: | 302GR93100 |
| Деталь: | PIN MOUNT LENS |
| Парткод: | 302GR17811 |
| Деталь: | WIRE CCD1 |
| Парткод: | 302GR46010 |
| Деталь: | LABEL,CAUTION CONTACT GLASS |
| Парткод: | 2A105180 |
| Деталь: | COVER ISU |
| Парткод: | 302GR17560 |
| Деталь: | PIN ISU |
| Парткод: | 302GR17660 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBFP007C001H01 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZGSTG151018H01 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+200H01 |
| Деталь: | MOUNT SCANNER PWB |
| Парткод: | 302GR17320 |
| Деталь: | SEAL LAMP INVERTER |
| Парткод: | 302GR17430 |
| Деталь: | SCANNER PWB ASSY WITH SOFTWARE |
| Парткод: | 302GR01040 |
| Деталь: | RETAINER REGURATOR |
| Парткод: | 302GR17330 |
| Деталь: | UNIT LAMP INVERTER |
| Парткод: | 302GR45080 |
| Деталь: | WIRE LAMP INVERTER |
| Парткод: | 302GR46060 |
| Деталь: | THERMAL SEAT |
| Парткод: | 7ZS22110301 + H01 |
| Деталь: | LID PWB S |
| Парткод: | 302GR17730 |
| Деталь: | BINDING BAND,KB-100-1 |
| Парткод: | M0207000 |
| Деталь: | WIRE SCANNER-IPU PWB |
| Парткод: | 302GR46080 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | SEAL SCANNER PWB |
| Парткод: | 302GR17890 |
| Деталь: | WIRE SCANNER POWER |
| Парткод: | 302GR46070 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 2BC07860 |
| Деталь: | PLATE NUMBER |
| Парткод: | 2BL04310 |
| Деталь: | PLATE NUMBER 2 |
| Парткод: | 2BL04370 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 2C904550 |
| Деталь: | PIN CURSOR |
| Парткод: | 2FB07050 |
| Деталь: | SPRING CURSOR |
| Парткод: | 2FB07060 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | SHAFT, WORK PLATE |
| Парткод: | 302AR07041 |
| Деталь: | WORK PLATE,LIFT CASSETTE |
| Парткод: | 302BC06091 |
| Деталь: | PLATE SIZE C |
| Парткод: | 302FB05200 |
| Деталь: | PLATE SIZE IN |
| Парткод: | 302FB05210 |
| Деталь: | LEVER CURSOR A |
| Парткод: | 302FB07032 |
| Деталь: | LEVER CURSOR B |
| Парткод: | 302FB07042 |
| Деталь: | ADJUSTING PLATE CASSETTE |
| Парткод: | 302FB07340 |
| Деталь: | PIN CASSETTE |
| Парткод: | 302FB07420 |
| Деталь: | BASE CASSETTE |
| Парткод: | 302FG07091 |
| Деталь: | CURSOR C CASSETTE |
| Парткод: | 302FG07151 |
| Деталь: | FRONT GUIDE C,CURSOR |
| Парткод: | 302FG07170 |
| Деталь: | REAR GUIDE C,CURSOR |
| Парткод: | 302FG07180 |
| Деталь: | GROUND PLATE,CASSETTE |
| Парткод: | 302FG07200 |
| Деталь: | STOPPER,TRAILING EDGE DETECTION |
| Парткод: | 302FG07230 |
| Деталь: | CASSETTE |
| Парткод: | 302GR09011 |
| Деталь: | HANDLE CASSETTE 1 |
| Парткод: | 302GR09020 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302GR09030 |
| Деталь: | HANDLE CASSETTE 2 |
| Парткод: | 302GR09040 |
| Деталь: | LEVER CASSETTE |
| Парткод: | 302GR09051 |
| Деталь: | RAIL CURSOR R |
| Парткод: | 302GR09060 |
| Деталь: | LID PAPER SIZE |
| Парткод: | 302GR09070 |
| Деталь: | RAIL CURSOR A |
| Парткод: | 302GR09080 |
| Деталь: | Support Plate |
| Парткод: | 302GR09090 |
| Деталь: | FRONT CURSOR CASSETTE |
| Парткод: | 302GR09102 |
| Деталь: | REAR CURSOR CASSETTE |
| Парткод: | 302GR09112 |
| Деталь: | SPRING LEVER CASSETTE |
| Парткод: | 302GR09120 |
| Деталь: | SHAFT PULLEY |
| Парткод: | 302GR09130 |
| Деталь: | SHAFT HANDLE |
| Парткод: | 302GR09140 |
| Деталь: | WORK PLATE HANDLE |
| Парткод: | 302GR09150 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302GR09160 |
| Деталь: | PLATE SIZE INCH |
| Парткод: | 302GR09201 |
| Деталь: | SEAL DETECTION PLATE |
| Парткод: | 302GR09210 |
| Деталь: | SPACER SIZE PLATE |
| Парткод: | 302GR09980 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09990 |
| Деталь: | LABEL CASSETTE OPERATION |
| Парткод: | 302GR34011 |
| Деталь: | LABEL PAPER SIZE |
| Парткод: | 302GR34022 |
| Деталь: | LABEL PAPER SIZE R |
| Парткод: | 302GR34032 |
| Деталь: | WIRE CASSETTE UNIT |
| Парткод: | 302GR46450 |
| Деталь: | DETECTION PLATE,PAPER SIZE |
| Парткод: | 33907170 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | PULLEY,CASSETTE |
| Парткод: | 34907150 |
| Деталь: | PLATE NUMBER4 |
| Парткод: | 3CF04060 |
| Деталь: | RETAINER M4 |
| Парткод: | 3CY06030 |
| Деталь: | RACK CURSOR |
| Парткод: | 3CY06090 |
| Деталь: | GEAR 20,CURSOR |
| Парткод: | 3CY06100 |
| Деталь: | PLATE NUMBER 3 /3CF0405 A4 |
| Парткод: | 5MVX321CE001 |
| Деталь: | CUSHION,CASSETTE R |
| Парткод: | 60907170 |
| Деталь: | LABEL,PAPER UPPER LIMIT |
| Парткод: | 61705110 |
| Деталь: | SPRING, PAD |
| Парткод: | 66106080 |
| Деталь: | PAD,CASSETTE |
| Парткод: | 66107100 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H01 |
| Деталь: | CT-710 |
| Парткод: | 302GR93082 |
| Деталь: | SHIELD 10X8X20,GASKET |
| Парткод: | 2AC26310 |
| Деталь: | FRONT PLATE EXIT L |
| Парткод: | 2BJ04520 |
| Деталь: | LEVER GUIDE CHANGE U |
| Парткод: | 2BJ21021 |
| Деталь: | SPRING CHANGE UP |
| Парткод: | 2BJ21030 |
| Деталь: | LEVER CHANGE UP B |
| Парткод: | 2BJ21040 |
| Деталь: | LEVER L COVER LOCK M |
| Парткод: | 2BL04550 |
| Деталь: | SPRING L COVER LOCK |
| Парткод: | 2BL04560 |
| Деталь: | LEVER COVER RELEASE |
| Парткод: | 2BL04600 |
| Деталь: | STRAP COVER |
| Парткод: | 2BL04680 |
| Деталь: | GROUND PLATE LEFT B |
| Парткод: | 2BL04700 |
| Деталь: | FILM WIRE PROTECT |
| Парткод: | 2BL21460 |
| Деталь: | GUIDE FILM DU |
| Парткод: | 2BL21490 |
| Деталь: | FILM WIRE PROTECT B |
| Парткод: | 2BL21500 |
| Деталь: | GROUND PLATE LEFT FAN |
| Парткод: | 2BL23110 |
| Деталь: | SPONGE LEFT FAN |
| Парткод: | 2BL23170 |
| Деталь: | REAR PLATE EXIT L |
| Парткод: | 302BJ04531 |
| Деталь: | LEFT COVER MIDDLE |
| Парткод: | 302BL04513 |
| Деталь: | SHAFT L COVER LOCK M |
| Парткод: | 302BL04541 |
| Деталь: | PLATE LEFT COVER M |
| Парткод: | 302BL04621 |
| Деталь: | LABEL VFEED CAUTION |
| Парткод: | 302FB05380 |
| Деталь: | LABEL VFEED CAUTION 6NATIONS |
| Парткод: | 302FB05440 |
| Деталь: | COVER EXIT LEFT |
| Парткод: | 302FG04062 |
| Деталь: | GUIDE CHANGE UP |
| Парткод: | 302FG21011 |
| Деталь: | MOUNT OZONE FILTER A |
| Парткод: | 302FG23021 |
| Деталь: | PIN LEFT COVER |
| Парткод: | 302GR02810 |
| Деталь: | SEAL PROTECT OZONE |
| Парткод: | 302GR04460 |
| Деталь: | GUIDE LEFT COVER M |
| Парткод: | 302GR28050 |
| Деталь: | FILTER VOC A |
| Парткод: | 302GR33080 |
| Деталь: | LABEL HIGH TEMP |
| Парткод: | 302GR34150 |
| Деталь: | FAN DU 60-15 |
| Парткод: | 302GR44040 |
| Деталь: | WIRE CONVEYING FAN |
| Парткод: | 302GR46310 |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | PULLEY FEED SHIFT |
| Парткод: | 2BL21330 |
| Деталь: | SPRING CHANGE PULLEY |
| Парткод: | 2BL21340 |
| Деталь: | SHAFT,PRESSURE ROLLER SEPARATION |
| Парткод: | 302AR20512 |
| Цена: | 160 ₽ |
| Деталь: | MOUNT REAR GUIDE |
| Парткод: | 302BL20092 |
| Деталь: | CLAW PRESS ROLLER |
| Парткод: | 302BL20351 |
| Деталь: | PIN REAR GUIDE FIXING |
| Парткод: | 302GR02840 |
| Деталь: | SPRING CLAW PRESS |
| Парткод: | 302GR25350 |
| Деталь: | REAR GUIDE FUSER |
| Парткод: | 302GR25370 |
| Деталь: | GUIDE EXIT L |
| Парткод: | 302GR28032 |
| Деталь: | GUIDE FEED SHIFT L |
| Парткод: | 302GR28040 |
| Деталь: | PLATE SHAFT PULLEY |
| Парткод: | 302GR28100 |
| Деталь: | SHAFT CHANGE PULLEY |
| Парткод: | 302GR28120 |
| Деталь: | SPRING,DEVELOPING ROCK |
| Парткод: | 65009050 |
| Деталь: | SHAFT FEED PULLEY |
| Парткод: | 302BL06212 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL16080 |
| Деталь: | STRAP RELEASE |
| Парткод: | 2BL06960 |
| Деталь: | LABEL LEFT COVER A |
| Парткод: | 302GR34040 |
| Деталь: | LEFT COVER FEED |
| Парткод: | 302BL06101 |
| Деталь: | SPRING FEED |
| Парткод: | 2BL06340 |
| Деталь: | CAM DLP |
| Парткод: | 302BL14241 |
| Деталь: | SPRING CAM |
| Парткод: | 2BL14410 |
| Деталь: | MOUNT CAM |
| Парткод: | 302BL14141 |
| Деталь: | SHAFT CAM |
| Парткод: | 302BL14231 |
| Деталь: | BUSH POM /F0093 A4 |
| Парткод: | 5MVM122DB003 |
| Деталь: | GEAR 18 |
| Парткод: | 2BL14250 |
| Деталь: | RETAINING PIN,VERTICAL CONVEYING |
| Парткод: | 302AR07541 |
| Деталь: | PARTS LEFT COVER MIDDLE ASSY |
| Парткод: | 302GR93332 |
| Деталь: | PARTS REAR GUIDE FUSER UNIT |
| Парткод: | 302GR93182 |
| Деталь: | GUIDE DLP |
| Парткод: | 2BL22140 |
| Деталь: | GEAR DRUM Z76H-Z30H |
| Парткод: | 2BL22160 |
| Деталь: | PLATE GUIDE DRUM |
| Парткод: | 2BL22170 |
| Деталь: | GEAR Z37H-Z28H |
| Парткод: | 2BL22180 |
| Деталь: | GEAR Z50H |
| Парткод: | 2BL22190 |
| Деталь: | GEAR JOINT Z32S |
| Парткод: | 2BL22210 |
| Деталь: | GEAR Z36S-Z31H |
| Парткод: | 2BL22220 |
| Деталь: | GEAR Z34H |
| Парткод: | 2BL22230 |
| Деталь: | SPRING JOINT FUSER |
| Парткод: | 2BL22240 |
| Деталь: | SHAFT DRIVE DRUM FW |
| Парткод: | 2BL22840 |
| Деталь: | PLATE DRIVE FRONT |
| Парткод: | 2FG22010 |
| Деталь: | GEAR Z59H-Z44S |
| Парткод: | 2FG22030 |
| Деталь: | GEAR Z22S |
| Парткод: | 2FG22040 |
| Деталь: | PLATE DRIVE REAR |
| Парткод: | 302FG22021 |
| Деталь: | GEAR DRUM Z70H |
| Парткод: | 302GR31030 |
| Деталь: | MOTOR MAIN |
| Парткод: | 302GR44100 |
| Деталь: | GEAR Z37S /40633V0081 A4 |
| Парткод: | 5MVG148DN027 |
| Деталь: | GEAR Z76H-Z35H /30633D0068 A3 |
| Парткод: | 5MVG169DN019 |
| Деталь: | BEARING 6900ZZNR |
| Парткод: | G3169000 |
| Деталь: | STAY DRUM COVER Z |
| Парткод: | 302GR02961 |
| Деталь: | MOTOR EJECT |
| Парткод: | 302GR44090 |
| Цена: | 3 800 ₽ |
| Деталь: | PLATE DRIVE EXIT A |
| Парткод: | 302FG22051 |
| Деталь: | GEAR Z47S-Z28S |
| Парткод: | 2BL22800 |
| Деталь: | GEAR EXIT Z30S |
| Парткод: | 2BL22630 |
| Деталь: | CLUTCH REGISTRATION |
| Парткод: | 302GR44140 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | DUCT UPPER DRUM |
| Парткод: | 302GR33010 |
| Деталь: | COVER DUCT DRUM |
| Парткод: | 2BL23120 |
| Деталь: | DUCT UPPER CONT |
| Парткод: | 302GR33020 |
| Деталь: | FAN FIXING 80-25 |
| Парткод: | 302GR44020 |
| Деталь: | LID DLP DUCT |
| Парткод: | 2BL23040 |
| Деталь: | RETAINER FLYWHEEL |
| Парткод: | 2BL22850 |
| Деталь: | FLYWHEEL 190 |
| Парткод: | 2BL22860 |
| Деталь: | WEIGHT 190 |
| Парткод: | 2BL22870 |
| Деталь: | MOUNT BASE TERMINAL |
| Парткод: | 302BL26151 |
| Деталь: | PLATE TRANSFER A |
| Парткод: | 2BL26160 |
| Деталь: | PLATE SEPARATION A |
| Парткод: | 2BL26170 |
| Деталь: | TONER SENSOR ASSY |
| Парткод: | 302GR01250 |
| Деталь: | DUCT MAIN A |
| Парткод: | 302BL23051 |
| Деталь: | DUCT MAIN B |
| Парткод: | 2BL23060 |
| Деталь: | FAN UPPER CONT 90-25 |
| Парткод: | 302GR44030 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | WIRE CONTAINER |
| Парткод: | 302GR46210 |
| Деталь: | RAIL DRUM R |
| Парткод: | 302BL02221 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PLATE DRIVE EXIT B |
| Парткод: | 2FG22060 |
| Деталь: | MOUNT FLYWHEEL |
| Парткод: | 2BL22890 |
| Деталь: | FILM COOLING |
| Парткод: | 2BL23100 |
| Деталь: | FILM BKT CLUTCH |
| Парткод: | 2BL22880 |
| Деталь: | BRACKET CLUTCH |
| Парткод: | 2BL22150 |
| Деталь: | BUSH,CUTTER |
| Парткод: | 213+4410 |
| Деталь: | FILM SPRING DRUM COVER |
| Парткод: | 302GR02560 |
| Деталь: | HOLDER RFID |
| Парткод: | 302GR33030 |
| Деталь: | R/W MODULE 26X45 |
| Парткод: | 302F845040 |
| Деталь: | WIRE RFID |
| Парткод: | 302GR46590 |
| Деталь: | COVER DRUM Z |
| Парткод: | 302GR02951 |
| Деталь: | SHAFT DRUM COVER Z |
| Парткод: | 302GR02970 |
| Деталь: | HOLDER SHAFT F |
| Парткод: | 302GR02030 |
| Деталь: | HOLDER SHAFT R |
| Парткод: | 302GR02040 |
| Деталь: | GUIDE STRAP |
| Парткод: | 302GR02050 |
| Деталь: | STRAP DRUM COVER |
| Парткод: | 302GR02060 |
| Деталь: | ARM DRUM COVER A |
| Парткод: | 302GR02071 |
| Деталь: | ARM DRUM COVER B |
| Парткод: | 302GR02081 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | DR-710 |
| Парткод: | 302GR93200 |
| Деталь: | Блок лазера |
| Парткод: | LK-710 |
| Цена: | 49 300 ₽ |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | SEAL WIRE |
| Парткод: | 2BL14480 |
| Деталь: | SPRING EXIT PULLEY |
| Парткод: | 2BL21070 |
| Деталь: | LEVER GUIDE CHANGE |
| Парткод: | 2BL21100 |
| Деталь: | ACTUATOR EXIT R |
| Парткод: | 2BL21120 |
| Деталь: | ACTUATOR EXIT L |
| Парткод: | 2BL21130 |
| Деталь: | PLATE EARTH EXIT F |
| Парткод: | 2BL21170 |
| Деталь: | PLATE EARTH EXIT R |
| Парткод: | 2BL21180 |
| Деталь: | BKT SOLENOID |
| Парткод: | 2BL21190 |
| Деталь: | PULLEY ONEWAY T30 |
| Парткод: | 2BL21211 |
| Деталь: | GEAR EXIT Z19 |
| Парткод: | 2BL21220 |
| Деталь: | PULLEY EXIT T30 |
| Парткод: | 2BL21230 |
| Деталь: | BELT EXIT P2M212 |
| Парткод: | 2BL21240 |
| Деталь: | SPRING ACTUATOR R |
| Парткод: | 2BL21250 |
| Деталь: | SPRING ACTUATOR L |
| Парткод: | 2BL21260 |
| Деталь: | SPRING FEED SHIFT |
| Парткод: | 2BL21270 |
| Деталь: | LEVER GUIDE CHANGE B |
| Парткод: | 2BL21370 |
| Деталь: | GEAR EXIT JOINT Z26S |
| Парткод: | 2BL21390 |
| Деталь: | SPRING EXIT JOINT |
| Парткод: | 2BL21400 |
| Деталь: | GEAR EXIT Z20 |
| Парткод: | 2BL21430 |
| Деталь: | SPRING EXIT CHANGE |
| Парткод: | 2BL21440 |
| Деталь: | PULLEY EXIT B |
| Парткод: | 2BL21450 |
| Деталь: | PLATE EARTH CHANGE |
| Парткод: | 2BL21470 |
| Деталь: | CUT WASHER 6 |
| Парткод: | 2BL21510 |
| Деталь: | COLLAR BELT |
| Парткод: | 2BL22580 |
| Деталь: | ROLLER EJECT J |
| Парткод: | 302BJ21051 |
| Деталь: | ROLLER FEED SHIFT |
| Парткод: | 302BL21031 |
| Деталь: | SHAFT EXIT PULLEY |
| Парткод: | 302BL21061 |
| Деталь: | GUIDE EXIT CHANGE |
| Парткод: | 302BL21081 |
| Деталь: | BKT DISCHARGER |
| Парткод: | 302BL21161 |
| Деталь: | JOINT EXIT |
| Парткод: | 302BL21202 |
| Деталь: | FRAME EXIT UP |
| Парткод: | 302GR28012 |
| Деталь: | FRAME EXIT LOW |
| Парткод: | 302GR28020 |
| Деталь: | SOLENOID FEED SHIFT |
| Парткод: | 302GR44160 |
| Деталь: | WIRE EJECT(C) |
| Парткод: | 302GR46140 |
| Деталь: | SWITCH,EJECT |
| Парткод: | 303BN27061 |
| Деталь: | STATIC ELIMINATOR,EJECT |
| Парткод: | 34821100 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | EDGING,EDS-0607L(KITAGAWA) |
| Парткод: | M2104390 |
| Деталь: | PIN EXIT |
| Парткод: | 302GR02860 |
| Деталь: | PARTS EXIT UNIT J |
| Парткод: | 302GY93020 |
| Деталь: | LK-710 |
| Парткод: | 302GR93091 |
| Деталь: | FRONT MOUNT HOUSING |
| Парткод: | 2BL13120 |
| Деталь: | PIN LSU FIXING |
| Парткод: | 302GR02830 |
| Деталь: | SPRING FIX LSU |
| Парткод: | 2BL13290 |
| Деталь: | FRONT ADJUSTING LSU |
| Парткод: | 2BL13070 |
| Деталь: | REAR ADJUSTING LSU |
| Парткод: | 2BL13060 |
| Деталь: | ADJUSTING PLT LSU |
| Парткод: | 2BL13250 |
| Деталь: | WIRE LSU |
| Парткод: | 302GR46150 |
| Деталь: | MOUNT FAN |
| Парткод: | 2BL02230 |
| Деталь: | FAN LSU 60-25 |
| Парткод: | 302GR44080 |
| Цена: | 2 800 ₽ |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SPONGE FAN |
| Парткод: | 2BL02240 |
| Деталь: | PARTS FILTER DUST F1 ASSY |
| Парткод: | 302GR94430 |
| Деталь: | PARTS FILTER DUST F2 ASSY |
| Парткод: | 302GR94440 |
| Деталь: | GEAR SPIRAL 16 |
| Парткод: | 2BL18160 |
| Деталь: | GEAR IDLE 15 |
| Парткод: | 2BL18170 |
| Деталь: | BLADE CLEANING |
| Парткод: | 2BL18300 |
| Деталь: | HANDLE DRUM |
| Парткод: | 2BL18320 |
| Деталь: | SPONGE LOWER SEAL |
| Парткод: | 2BL18560 |
| Деталь: | BUSHING DRUM A |
| Парткод: | 2BL18630 |
| Деталь: | TAPE CLEANING LAMP |
| Парткод: | 2BL18720 |
| Деталь: | GEAR CL ROLLER 15 |
| Парткод: | 2BL18870 |
| Деталь: | GEAR CL ROLLER 16 |
| Парткод: | 2BL18880 |
| Деталь: | REAR COVER DRUM |
| Парткод: | 302BL18031 |
| Деталь: | FRONT COVER DRUM |
| Парткод: | 302GR12010 |
| Деталь: | LOWER SEAL CLEANING |
| Парткод: | 302GR12110 |
| Деталь: | LAMP CLEANING |
| Парткод: | 302GR44230 |
| Деталь: | PARTS CLAW SEPARATION ASSY |
| Парткод: | 302GR93190 |
| Деталь: | MC-710 |
| Парткод: | 302GR93071 |
| Деталь: | PARTS MCH MOTOR ASSY |
| Парткод: | 302GR94451 |
| Деталь: | DK-715 (30ppm) |
| Парткод: | 302GN93011 |
| Деталь: | DK-716 (40/50ppm) |
| Парткод: | 302GR93041 |
| Деталь: | PARTS MCH MOTOR SET ASSY |
| Парткод: | 302GR94530 |
| Деталь: | SPONGE LCD B |
| Парткод: | 2BJ25280 |
| Деталь: | KEY RESET |
| Парткод: | 302BJ25051 |
| Деталь: | KEY POWER SUPPLY |
| Парткод: | 302FB24061 |
| Деталь: | KEY PRINT |
| Парткод: | 302FB24200 |
| Деталь: | OPERATION RIGHT PWB ASSY |
| Парткод: | 302GR01090 |
| Деталь: | OPERATION LEFT PWB ASSY |
| Парткод: | 302GR01100 |
| Деталь: | OPERATION UPPER PWB ASSY |
| Парткод: | 302GR01110 |
| Деталь: | COVER OPERATION A |
| Парткод: | 302GR05012 |
| Деталь: | KEY PRO |
| Парткод: | 302GR05150 |
| Деталь: | KEY APPLI |
| Парткод: | 302GR05160 |
| Деталь: | KEY STATUS |
| Парткод: | 302GR05170 |
| Деталь: | LENS KEY A |
| Парткод: | 302GR05180 |
| Деталь: | KEY COPY |
| Парткод: | 302GR05190 |
| Деталь: | KEY SEND |
| Парткод: | 302GR05200 |
| Деталь: | KEY DOC |
| Парткод: | 302GR05210 |
| Деталь: | LENS KEY B |
| Парткод: | 302GR05220 |
| Деталь: | KEY SYSTEM |
| Парткод: | 302GR05230 |
| Деталь: | KEY COUNTER |
| Парткод: | 302GR05240 |
| Деталь: | KEY ACCESS |
| Парткод: | 302GR05250 |
| Деталь: | KEY HELP |
| Парткод: | 302GR05260 |
| Деталь: | KEY LOG OUT |
| Парткод: | 302GR05270 |
| Деталь: | LENS POWER LED |
| Парткод: | 302GR05280 |
| Деталь: | LENS LED |
| Парткод: | 302GR05290 |
| Деталь: | KEY OPE 10 |
| Парткод: | 302GR05300 |
| Деталь: | SPONGE LCD A |
| Парткод: | 302GR05310 |
| Деталь: | GROUND PLATE OPE A |
| Парткод: | 302GR05320 |
| Деталь: | HOLDER INVERTER |
| Парткод: | 302GR05370 |
| Деталь: | MOUNT LCD |
| Парткод: | 302GR05381 |
| Деталь: | HOLDER LCD A |
| Парткод: | 302GR05400 |
| Деталь: | HOLDER LCD B |
| Парткод: | 302GR05410 |
| Деталь: | KEY STOP |
| Парткод: | 302GR05610 |
| Деталь: | FILM OPERATION B |
| Парткод: | 302GR05660 |
| Деталь: | SPACER KEY |
| Парткод: | 302GR05700 |
| Деталь: | SHEET OPE SET J(TW) |
| Парткод: | 302GR05790 |
| Деталь: | SHEET OPERATION A |
| Парткод: | 302GR05910 |
| Деталь: | SHEET OPERATION B |
| Парткод: | 302GR05920 |
| Деталь: | LCD OPERATION |
| Парткод: | 302GR45040 |
| Деталь: | TABLET OPERATION |
| Парткод: | 302GR45050 |
| Деталь: | LCD INVERTER |
| Парткод: | 302GR45070 |
| Деталь: | WIRE PANEL LCD |
| Парткод: | 302GR46170 |
| Деталь: | WIRE OPERATION RIGHT |
| Парткод: | 302GR46320 |
| Деталь: | WIRE OPERATION LEFT |
| Парткод: | 302GR46540 |
| Деталь: | WIRE OPERATION UPPER |
| Парткод: | 302GR46550 |
| Деталь: | WIRE PANEL INVERTER |
| Парткод: | 302GR46570 |
| Деталь: | PARTS,PWB PANEL ASSY,SP |
| Парткод: | 302GR94150 |
| Деталь: | PARTS,PWB PANEL CODE DIMM ASSY TW |
| Парткод: | 302GR94540 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SPACER,KGPS-5RF(KITAGAWA) |
| Парткод: | M2108880 |
| Деталь: | FILM PROTECT WIRE |
| Парткод: | 302GR05930 |
| Деталь: | WIRE OPERATION FRONT |
| Парткод: | 302GR46560 |
| Деталь: | OPERATION FRONT PWB ASSY |
| Парткод: | 302GR01120 |
| Деталь: | WIRE PANEL POWER |
| Парткод: | 302GR46180 |
| Деталь: | HOUSING LED PWB |
| Парткод: | 302GR39131 |
| Деталь: | COVER OPERATION B |
| Парткод: | 302GR05021 |
| Деталь: | HINGE OPERATION L |
| Парткод: | 302GR05030 |
| Деталь: | HINGE OPERATION R |
| Парткод: | 302GR05040 |
| Деталь: | GROUND PLATE DECK UNIT |
| Парткод: | 302FB09320 |
| Деталь: | FILM OPERATION A |
| Парткод: | 302GR05650 |
| Деталь: | BASE OPERATION |
| Парткод: | 302GR05050 |
| Деталь: | MOUNT HANDLE OPE |
| Парткод: | 302GR05060 |
| Деталь: | HANDLE OPE |
| Парткод: | 302GR05070 |
| Деталь: | CUSHION HANDLE A |
| Парткод: | 302GR05080 |
| Деталь: | BUSH PIN OPE |
| Парткод: | 302GR05090 |
| Деталь: | SPRING HINGE OPE L |
| Парткод: | 302GR05100 |
| Деталь: | SPRING HINGE OPE R |
| Парткод: | 302GR05110 |
| Деталь: | MOUNT SLIDE |
| Парткод: | 302GR05120 |
| Деталь: | PIN OPERATION |
| Парткод: | 302GR05130 |
| Деталь: | SPRING MOUNT HANDLE A |
| Парткод: | 302GR05350 |
| Деталь: | MOUNT USB TERMINAL |
| Парткод: | 302GR05500 |
| Деталь: | GROUND PLATE OPE B |
| Парткод: | 302GR05510 |
| Деталь: | GROUND PLATE OPE C |
| Парткод: | 302GR05520 |
| Деталь: | FILM OPE A |
| Парткод: | 302GR05620 |
| Деталь: | FILM PROTECT |
| Парткод: | 302GR04480 |
| Деталь: | FAN OPE 40-10 |
| Парткод: | 302GR44010 |
| Деталь: | SPEAKER |
| Парткод: | 7YG57S011GP+H01 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+013H01 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+025H01 |
| Деталь: | SHEET OPE PROTECT B |
| Парткод: | 302GR04470 |
| Деталь: | WIRE MAIN-PANEL USB |
| Парткод: | 302GR46510 |
| Деталь: | WIRE MAIN-PANEL IF |
| Парткод: | 302GR46520 |
| Деталь: | WIRE PANEL USB |
| Парткод: | 302GR46530 |
| Деталь: | PARTS OPERATION UNIT TW |
| Парткод: | 302GR93521 |
| Деталь: | SEAL FRAME A |
| Парткод: | 302GR17410 |
| Деталь: | SEAL FRAME B |
| Парткод: | 302GR17420 |
| Деталь: | SEAL GUIDE WIRE D |
| Парткод: | 302GR17450 |
| Деталь: | SEAL FRAME C |
| Парткод: | 302GR17460 |
| Деталь: | MIRROR C |
| Парткод: | 302GR17960 |
| Деталь: | MOUNT DP HINGE |
| Парткод: | 302GR17270 |
| Деталь: | PIN WIRE PULLEY B |
| Парткод: | 302GR17350 |
| Деталь: | PULLEY SCANNER |
| Парткод: | 302GR17820 |
| Деталь: | DRUM PULLEY |
| Парткод: | 2C912340 |
| Деталь: | REAR WIRE SCANNER |
| Парткод: | 302GR17100 |
| Деталь: | FRONT WIRE SCANNER |
| Парткод: | 302GR17110 |
| Деталь: | SHAFT SCANNER |
| Парткод: | 302GR17190 |
| Деталь: | BEARING,688ZZNR |
| Парткод: | 28107400 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PULLEY SCANNER 43 |
| Парткод: | 302GR17210 |
| Деталь: | MIRROR FRAME B |
| Парткод: | 302GR17091 |
| Деталь: | MIRROR B |
| Парткод: | 302GR17280 |
| Деталь: | MIRROR HOLDER |
| Парткод: | 75712080 |
| Деталь: | SLIDER SCANNER |
| Парткод: | 2DC12230 |
| Деталь: | ADJUSTING PLATE B |
| Парткод: | 302GR17131 |
| Деталь: | GUIDE WIRE B |
| Парткод: | 302GR17150 |
| Деталь: | STOPPER PI |
| Парткод: | 302GR17970 |
| Деталь: | SPRING SCANNER TENSION |
| Парткод: | 302C912291 |
| Деталь: | SPRING,MIRROR HOLDER |
| Парткод: | 2BC12190 |
| Деталь: | MIRROR A |
| Парткод: | 2FB12140 |
| Деталь: | MIRROR FRAME A |
| Парткод: | 302GR17082 |
| Деталь: | REFLECTOR SCANNER |
| Парткод: | 302GR17250 |
| Деталь: | FILM LAMP |
| Парткод: | 302GR17400 |
| Деталь: | TAPE REFLECTOR |
| Парткод: | 302GR17620 |
| Деталь: | RETAINER WIRE |
| Парткод: | 2C912150 |
| Деталь: | GUIDE WIRE C |
| Парткод: | 302GR17160 |
| Деталь: | LAMP SCANNER |
| Парткод: | 302GR17120 |
| Деталь: | GUIDE WIRE A |
| Парткод: | 302GR17140 |
| Деталь: | HOLDER GUIDE WIRE C |
| Парткод: | 302GR17440 |
| Деталь: | MOTOR SCANNER |
| Парткод: | 302GR44270 |
| Деталь: | PULLEY SCANNER 47/34 |
| Парткод: | 302GR17200 |
| Деталь: | MOUNT SCANNER DRIVE |
| Парткод: | 302GR17220 |
| Деталь: | CUT WASHER |
| Парткод: | 5MVS665KB001 |
| Деталь: | BELT SCANNER |
| Парткод: | 302GR17230 |
| Деталь: | MOUNT RELEASE SWITCH |
| Парткод: | 302GR17300 |
| Деталь: | SWITCH RELEASE |
| Парткод: | 302GR17370 |
| Деталь: | SPRING RELEASE SWITCH |
| Парткод: | 302GR17380 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | SENSOR ORIGINAL |
| Парткод: | 2C927090 |
| Деталь: | GUIDE WIRE D |
| Парткод: | 302GR17740 |
| Деталь: | WIRE SHD-SCANNER PWB |
| Парткод: | 302GR46021 |
| Деталь: | WIRE SCANNER HP SW |
| Парткод: | 302GR46040 |
| Деталь: | WIRE CCD DATA |
| Парткод: | 302GR46091 |
| Деталь: | SHD PWB ASSY |
| Парткод: | 302GR01050 |
| Деталь: | GUIDE FFC |
| Парткод: | 302GR17340 |
| Деталь: | GUIDE WIRE E |
| Парткод: | 302GR17770 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | BASE RUBBER,SCANNER SECTION |
| Парткод: | 2AV12280 |
| Деталь: | SEAL SCANNER FRAME E |
| Парткод: | 302GR17930 |
| Деталь: | PLATE PULLEY |
| Парткод: | 302GR17860 |
| Деталь: | PULLEY,LIFT WIRE |
| Парткод: | 2BC07050 |
| Деталь: | PIN SCANNER RETAINING |
| Парткод: | 302GR17180 |
| Деталь: | SEAL SCANNER |
| Парткод: | 302DA12070 |
| Деталь: | HOLDER BEARING |
| Парткод: | 302GR17880 |
| Деталь: | HOLDER PI |
| Парткод: | 302GR17750 |
| Деталь: | HOLDER RETAINER A |
| Парткод: | 302GR17900 |
| Деталь: | PLATE MIRROR B |
| Парткод: | 302GR17830 |
| Деталь: | SEAL PLATE MIRROR B |
| Парткод: | 302GR17840 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | PULLEY PLATE B |
| Парткод: | 302GR17980 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | COVER SCREW |
| Парткод: | 302BG04560 |
| Деталь: | Ось узла подачи бумаги |
| Парткод: | 302AR07252 |
| Цена: | 420 ₽ |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | UPPERGUIDE BYPASS |
| Парткод: | 2BL06520 |
| Деталь: | MOUNT RAIL |
| Парткод: | 2BL06570 |
| Деталь: | RAIL BYPASS |
| Парткод: | 2BL06580 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BL06590 |
| Деталь: | ACTUATOR BYPASSFEED |
| Парткод: | 2BL06730 |
| Деталь: | SPRING BYPASSFEED |
| Парткод: | 2BL06780 |
| Деталь: | GROUNDPLATE BYPASS |
| Парткод: | 2BL06790 |
| Деталь: | SPRING BYPASS |
| Парткод: | 2BL06800 |
| Деталь: | BELT BYPASSFEED |
| Парткод: | 2BL06810 |
| Деталь: | PULLEY25 BYPASSFEED |
| Парткод: | 2BL06820 |
| Деталь: | DIAL BYPASSFEED |
| Парткод: | 2BL06830 |
| Деталь: | ROLLER2 BYPASSFEED |
| Парткод: | 302BL06541 |
| Деталь: | ROLLER4 BYPASSFEED |
| Парткод: | 302BL06561 |
| Деталь: | SHAFT BYPASSFEED |
| Парткод: | 302BL06741 |
| Деталь: | SPRING BYPASSFEED |
| Парткод: | 302GR06510 |
| Деталь: | BASE BYPASS FEED |
| Парткод: | 302GR08100 |
| Деталь: | FILM UPPER GUIDE |
| Парткод: | 302GR08110 |
| Деталь: | LABEL JAM A1 |
| Парткод: | 302GR34050 |
| Деталь: | LABEL JAM A2 |
| Парткод: | 302GR34060 |
| Деталь: | LABEL JAM A3 |
| Парткод: | 302GR34070 |
| Деталь: | RIGHT PULLEY,FEED |
| Парткод: | 33906660 |
| Деталь: | GEAR 18 |
| Парткод: | 36722860 |
| Деталь: | PARTS BYPASS FEED UNIT |
| Парткод: | 302GR93120 |
| Деталь: | PARTS,PWB ENGINE ASSY,SP |
| Парткод: | 302GR94131 |
| Деталь: | BOX MOUNT PWB |
| Парткод: | 302GR39010 |
| Деталь: | FAN CONTROLLER 80-15 |
| Парткод: | 302GR44050 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610005++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PLATE GUIDE KUIO |
| Парткод: | 302GR39070 |
| Деталь: | KUIO PWB ASSY |
| Парткод: | 302GR01230 |
| Деталь: | PANEL GUIDE KUIO |
| Парткод: | 302GR39060 |
| Деталь: | GUIDE HARNESS |
| Парткод: | 302GR39160 |
| Деталь: | WIRE IB11 JUNCTION |
| Парткод: | 302GR46690 |
| Деталь: | WIRE MAIN-DP |
| Парткод: | 302GR46401 |
| Деталь: | WIRE MAIN-ENGINE PWB |
| Парткод: | 302GR46470 |
| Деталь: | WIRE FAN |
| Парткод: | 302GR46630 |
| Деталь: | MOUNT MAIN PWB |
| Парткод: | 302GR39050 |
| Деталь: | GUID CF CARD /45252C0006 A4 |
| Парткод: | 5MVX621SH003 |
| Деталь: | STORAGE DEVICE |
| Парткод: | 7NH3M040G001H01 |
| Деталь: | WIRE HARD DISK |
| Парткод: | 302GR46380 |
| Деталь: | PARTS,PWB MAIN CODE DIMM ASSY,SP |
| Парткод: | 302GR94201 |
| Деталь: | WIRE HDD |
| Парткод: | 2FB27390 |
| Деталь: | LID MMD |
| Парткод: | 2BJ26150 |
| Деталь: | LID SIMM |
| Парткод: | 302GR39040 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+032H01 |
| Деталь: | LID BOX MOUNT |
| Парткод: | 302GR39030 |
| Деталь: | LID CF CARD |
| Парткод: | 302GR39150 |
| Деталь: | FAN OPE 40-10 |
| Парткод: | 302GR44010 |
| Деталь: | HOLDER USB KEY |
| Парткод: | 302GR39170 |
| Деталь: | WIRE CPU FAN |
| Парткод: | 302GR46710 |
| Деталь: | HOLDER MAIN PWB |
| Парткод: | 302GR39100 |
| Деталь: | WIRE POWER-MAIN |
| Парткод: | 302GR46480 |
| Деталь: | WIRE CPU FAN JUNCTION |
| Парткод: | 302GR46720 |
| Деталь: | PLATE,OPTION |
| Парткод: | 303BH26021 |
| Деталь: | CORE 7-15X18 |
| Парткод: | 33927590 |
| Деталь: | WIRE KUIO FFC1 |
| Парткод: | 302GR46660 |
| Деталь: | WIRE KUIO FFC2 |
| Парткод: | 302GR46670 |
| Деталь: | WIRE USB JUNCTION |
| Парткод: | 302GR46580 |
| Деталь: | PARTS,PWB MAIN ASSY,SP (30ppm) |
| Парткод: | 302GN94010 |
| Деталь: | PARTS,PWB MAIN ASSY,SP (40/50ppm) |
| Парткод: | 302GR94121 |
| Деталь: | CLAMP,EMT-6N(TAKEUCHI) |
| Парткод: | M7005020 |
| Деталь: | SCREW OP / M3 X 8 CRFREE A4 |
| Парткод: | 5MMT263SN012++R |
| Деталь: | CLAMP,EMT-5N(TAKEUCHI) |
| Парткод: | M7005030 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | SCREW SCSI |
| Парткод: | 302GR39700 |
| Деталь: | SHEET HARNESS |
| Парткод: | 302GR39180 |
| Деталь: | SPONGE PROTECT |
| Парткод: | 302GR39200 |
| Деталь: | Вал переноса заряда, в сборе |
| Парткод: | TR-710 |
| Цена: | 6 600 ₽ |
| Деталь: | Блок проявки |
| Парткод: | DV-715 |
| Деталь: | Узел переноса заряда в драм-картридже, в сборе |
| Парткод: | MC-710 |
| Деталь: | SPONGE LCD B |
| Парткод: | 2BJ25280 |
| Деталь: | KEY RESET |
| Парткод: | 302BJ25051 |
| Деталь: | KEY POWER SUPPLY |
| Парткод: | 302FB24061 |
| Деталь: | KEY PRINT |
| Парткод: | 302FB24200 |
| Деталь: | OPERATION RIGHT PWB ASSY |
| Парткод: | 302GR01090 |
| Деталь: | OPERATION LEFT PWB ASSY |
| Парткод: | 302GR01100 |
| Деталь: | OPERATION UPPER PWB ASSY |
| Парткод: | 302GR01110 |
| Деталь: | COVER OPERATION A |
| Парткод: | 302GR05012 |
| Деталь: | KEY PRO |
| Парткод: | 302GR05150 |
| Деталь: | KEY APPLI |
| Парткод: | 302GR05160 |
| Деталь: | KEY STATUS |
| Парткод: | 302GR05170 |
| Деталь: | LENS KEY A |
| Парткод: | 302GR05180 |
| Деталь: | KEY COPY |
| Парткод: | 302GR05190 |
| Деталь: | KEY SEND |
| Парткод: | 302GR05200 |
| Деталь: | KEY DOC |
| Парткод: | 302GR05210 |
| Деталь: | LENS KEY B |
| Парткод: | 302GR05220 |
| Деталь: | KEY SYSTEM |
| Парткод: | 302GR05230 |
| Деталь: | KEY COUNTER |
| Парткод: | 302GR05240 |
| Деталь: | KEY ACCESS |
| Парткод: | 302GR05250 |
| Деталь: | KEY HELP |
| Парткод: | 302GR05260 |
| Деталь: | KEY LOG OUT |
| Парткод: | 302GR05270 |
| Деталь: | LENS POWER LED |
| Парткод: | 302GR05280 |
| Деталь: | LENS LED |
| Парткод: | 302GR05290 |
| Деталь: | KEY OPE 10 |
| Парткод: | 302GR05300 |
| Деталь: | SPONGE LCD A |
| Парткод: | 302GR05310 |
| Деталь: | GROUND PLATE OPE A |
| Парткод: | 302GR05320 |
| Деталь: | HOLDER INVERTER |
| Парткод: | 302GR05370 |
| Деталь: | MOUNT LCD |
| Парткод: | 302GR05381 |
| Деталь: | HOLDER LCD A |
| Парткод: | 302GR05400 |
| Деталь: | HOLDER LCD B |
| Парткод: | 302GR05410 |
| Деталь: | KEY STOP |
| Парткод: | 302GR05610 |
| Деталь: | FILM OPERATION B |
| Парткод: | 302GR05660 |
| Деталь: | SPACER KEY |
| Парткод: | 302GR05700 |
| Деталь: | SHEET OPE SET B |
| Парткод: | 302GR05820 |
| Деталь: | SHEET OPE SET C |
| Парткод: | 302GR05830 |
| Деталь: | SHEET OPE SET D |
| Парткод: | 302GR05840 |
| Деталь: | SHEET OPE SET E |
| Парткод: | 302GR05851 |
| Деталь: | SHEET OPE SET F |
| Парткод: | 302GR05860 |
| Деталь: | SHEET OPE SET G |
| Парткод: | 302GR05870 |
| Деталь: | SHEET OPE SET H |
| Парткод: | 302GR05880 |
| Деталь: | SHEET OPE SET I |
| Парткод: | 302GR05890 |
| Деталь: | SHEET OPERATION A |
| Парткод: | 302GR05910 |
| Деталь: | SHEET OPERATION B |
| Парткод: | 302GR05920 |
| Деталь: | LCD OPERATION |
| Парткод: | 302GR45040 |
| Деталь: | TABLET OPERATION |
| Парткод: | 302GR45050 |
| Деталь: | LCD INVERTER |
| Парткод: | 302GR45070 |
| Деталь: | WIRE PANEL LCD |
| Парткод: | 302GR46170 |
| Деталь: | WIRE OPERATION RIGHT |
| Парткод: | 302GR46320 |
| Деталь: | WIRE OPERATION LEFT |
| Парткод: | 302GR46540 |
| Деталь: | WIRE OPERATION UPPER |
| Парткод: | 302GR46550 |
| Деталь: | WIRE PANEL INVERTER |
| Парткод: | 302GR46570 |
| Деталь: | PARTS,PWB PANEL ASSY,SP |
| Парткод: | 302GR94150 |
| Деталь: | PARTS,PWB PANEL CODE DIMM ASSY,SP |
| Парткод: | 302GR94181 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SPACER,KGPS-5RF(KITAGAWA) |
| Парткод: | M2108880 |
| Деталь: | FILM PROTECT WIRE |
| Парткод: | 302GR05930 |
| Деталь: | GROUND PLATE DECK UNIT |
| Парткод: | 302FB09320 |
| Деталь: | FILM OPERATION A |
| Парткод: | 302GR05650 |
| Деталь: | BASE OPERATION |
| Парткод: | 302GR05050 |
| Деталь: | MOUNT HANDLE OPE |
| Парткод: | 302GR05060 |
| Деталь: | HANDLE OPE |
| Парткод: | 302GR05070 |
| Деталь: | CUSHION HANDLE A |
| Парткод: | 302GR05080 |
| Деталь: | BUSH PIN OPE |
| Парткод: | 302GR05090 |
| Деталь: | SPRING HINGE OPE L |
| Парткод: | 302GR05100 |
| Деталь: | SPRING HINGE OPE R |
| Парткод: | 302GR05110 |
| Деталь: | MOUNT SLIDE |
| Парткод: | 302GR05120 |
| Деталь: | PIN OPERATION |
| Парткод: | 302GR05130 |
| Деталь: | SPRING MOUNT HANDLE A |
| Парткод: | 302GR05350 |
| Деталь: | MOUNT USB TERMINAL |
| Парткод: | 302GR05500 |
| Деталь: | GROUND PLATE OPE B |
| Парткод: | 302GR05510 |
| Деталь: | GROUND PLATE OPE C |
| Парткод: | 302GR05520 |
| Деталь: | FILM OPE A |
| Парткод: | 302GR05620 |
| Деталь: | FILM PROTECT |
| Парткод: | 302GR04480 |
| Деталь: | FAN OPE 40-10 |
| Парткод: | 302GR44010 |
| Деталь: | SPEAKER |
| Парткод: | 7YG57S011GP+H01 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+013H01 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+025H01 |
| Деталь: | SHEET OPE PROTECT B |
| Парткод: | 302GR04470 |
| Деталь: | WIRE OPERATION FRONT |
| Парткод: | 302GR46560 |
| Деталь: | OPERATION FRONT PWB ASSY |
| Парткод: | 302GR01120 |
| Деталь: | WIRE PANEL POWER |
| Парткод: | 302GR46180 |
| Деталь: | HOUSING LED PWB |
| Парткод: | 302GR39131 |
| Деталь: | COVER OPERATION B |
| Парткод: | 302GR05021 |
| Деталь: | HINGE OPERATION L |
| Парткод: | 302GR05030 |
| Деталь: | HINGE OPERATION R |
| Парткод: | 302GR05040 |
| Деталь: | WIRE MAIN-PANEL USB |
| Парткод: | 302GR46510 |
| Деталь: | WIRE MAIN-PANEL IF |
| Парткод: | 302GR46520 |
| Деталь: | WIRE PANEL USB |
| Парткод: | 302GR46530 |
| Деталь: | PARTS OPERATION UNIT |
| Парткод: | 302GR93015 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | GEAR Z24S-P40 |
| Парткод: | 2BL22480 |
| Деталь: | GEAR Z40S-Z25S |
| Парткод: | 2BL22490 |
| Деталь: | SPRING DRIVE CONT |
| Парткод: | 2BL22510 |
| Деталь: | CLUTCH CONTAINER |
| Парткод: | 2BL22520 |
| Деталь: | PULLEY CONT DRIVE |
| Парткод: | 2BL22560 |
| Деталь: | BUSH DRIVE CONT 8 |
| Парткод: | 2BL22570 |
| Деталь: | BELT DRIVE CONTAINER |
| Парткод: | 2BL22590 |
| Деталь: | PLATE DRIVE CONT.A |
| Парткод: | 302BL22442 |
| Деталь: | PLATE DRIVE CONT. B |
| Парткод: | 302BL22451 |
| Деталь: | SHAFT DRIVE CONT |
| Парткод: | 302BL22461 |
| Деталь: | COUPLING G CONT |
| Парткод: | 302GR31010 |
| Деталь: | COUPLING H CONT |
| Парткод: | 302GR31020 |
| Деталь: | SOLENOID TONER |
| Парткод: | 302GR44150 |
| Цена: | 400 ₽ |
| Деталь: | WIRE CONT SW |
| Парткод: | 302GR46250 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | WIRE SADDLE,YMW-16(KITAGAWA) |
| Парткод: | M2109410 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GEAR M FEED Z25 /D1026 A4 |
| Парткод: | 5MVG137DB025 |
| Деталь: | GEAR FEED Z41S-P15 |
| Парткод: | 2BL22530 |
| Деталь: | MOTOR LIFT |
| Парткод: | 302GR44112 |
| Деталь: | BRACKET CLUTCH FEED |
| Парткод: | 2FG22090 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | GEAR Z60S-P20 |
| Парткод: | 2BL22540 |
| Деталь: | PRIMARY PAPER FEED BUSHING ASSY |
| Парткод: | 2AR00170 |
| Деталь: | GEAR Z41S P18 |
| Парткод: | 2BL22420 |
| Деталь: | BELT DRIVE MPF |
| Парткод: | 2BL22400 |
| Деталь: | PLATE DRIVE MPF A |
| Парткод: | 302BL22371 |
| Деталь: | GEAR Z40S-Z32S |
| Парткод: | 2BL22550 |
| Цена: | 550 ₽ |
| Деталь: | PLATE DRIVE MPF B |
| Парткод: | 2BL22380 |
| Деталь: | PLATE DRIVE FEED A |
| Парткод: | 302FG22071 |
| Деталь: | MOTOR FEED |
| Парткод: | 302GR44060 |
| Деталь: | GEAR Z76H-Z35S |
| Парткод: | 2BL22320 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | COLLAR BELT |
| Парткод: | 2BL22580 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510009++H01 |
| Деталь: | CLUTCH FEED |
| Парткод: | 302GR44120 |
| Деталь: | PLATE TENSION A |
| Парткод: | 302BL22811 |
| Деталь: | PIN DRIVE TENSION |
| Парткод: | 302GR02820 |
| Деталь: | PULLEY TENSION |
| Парткод: | 2BL22830 |
| Деталь: | SPRING PULLEY |
| Парткод: | 2BL22820 |
| Деталь: | PULLEY MPF DRIVE |
| Парткод: | 302BL22391 |
| Деталь: | PLATE DRIVE FEED B |
| Парткод: | 2FG22080 |
| Деталь: | GEAR Z41S-Z24S-P30 |
| Парткод: | 2BL22330 |
| Деталь: | BELT DRIVE FEED |
| Парткод: | 2BL22350 |
| Деталь: | COLLAR BELT DRIVE |
| Парткод: | 302FG22120 |
| Деталь: | PARTS CONT DRIVE A ASSY |
| Парткод: | 302GR93211 |
| Деталь: | PARTS CONT DRIVE E ASSY |
| Парткод: | 302GR93221 |
| Деталь: | Крышка лотка ручной подачи бумаги |
| Парткод: | 302BL06601 |
| Цена: | 3 700 ₽ |
| Деталь: | GEAR,TONER ROLLER |
| Парткод: | 29415100 |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 2BC07860 |
| Деталь: | PULLEY FEED A |
| Парткод: | 2BJ06010 |
| Цена: | 250 ₽ |
| Деталь: | COVER BYPASSUNIT |
| Парткод: | 2BL06530 |
| Деталь: | COVER BYPASSTRAY |
| Парткод: | 2BL06600 |
| Деталь: | STAY LIFTPLATE |
| Парткод: | 2BL06650 |
| Деталь: | CAM BYPASS |
| Парткод: | 2BL06680 |
| Деталь: | MOUNT BYPASSDRIVE |
| Парткод: | 2BL06690 |
| Деталь: | GEAR 55/15 |
| Парткод: | 2BL06720 |
| Деталь: | JOINT RETARD |
| Парткод: | 2BL06850 |
| Деталь: | SPRING RETARD |
| Парткод: | 2BL06860 |
| Деталь: | SPRING JOINTRETARD |
| Парткод: | 2BL06870 |
| Деталь: | FILM BYPASS |
| Парткод: | 2BL06880 |
| Деталь: | STOPPER GEAR 8-25 |
| Парткод: | 2BL06990 |
| Деталь: | SPRING BYPASS |
| Парткод: | 2BL07860 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | PIN COVER |
| Парткод: | 302BL04411 |
| Деталь: | SHAFT RETARD |
| Парткод: | 302BL06751 |
| Деталь: | SHAFT BYPASSCAM |
| Парткод: | 302BL06761 |
| Деталь: | SHAFT BYPASS |
| Парткод: | 302BL06771 |
| Деталь: | BASE BYPASS |
| Парткод: | 302GR08011 |
| Деталь: | PLATE LIFT BYPASS |
| Парткод: | 302GR08021 |
| Деталь: | COVER CURSOR |
| Парткод: | 302GR08030 |
| Деталь: | FRONT CURSOR BYPASS |
| Парткод: | 302GR08040 |
| Деталь: | REAR CURSOR BYPASS |
| Парткод: | 302GR08050 |
| Деталь: | MOUNT SIZE PWB |
| Парткод: | 302GR08060 |
| Деталь: | RACK CURSOR |
| Парткод: | 302GR08070 |
| Деталь: | TABLE BYPASS |
| Парткод: | 302GR08080 |
| Деталь: | CUSHION MPF A |
| Парткод: | 302GR08090 |
| Деталь: | LABEL SET PAPER CAUTION A |
| Парткод: | 302GR34090 |
| Деталь: | LABEL SET PAPER CAUTION E |
| Парткод: | 302GR34100 |
| Деталь: | LABEL SET PAPER CAUTION J |
| Парткод: | 302GR34110 |
| Деталь: | LABEL BYPASS SIZE |
| Парткод: | 302GR34122 |
| Деталь: | LABEL JAM A4 |
| Парткод: | 302GR34250 |
| Деталь: | LABEL SET PAPER CAUTION |
| Парткод: | 302GR34260 |
| Деталь: | LABEL SET PAPER CAUTION TW |
| Парткод: | 302GR34410 |
| Деталь: | CLUTCH FEED |
| Парткод: | 302GR44120 |
| Деталь: | CLUTCH FEED B |
| Парткод: | 302GR44131 |
| Деталь: | SWITCH BYPASS SIZE |
| Парткод: | 302GR44280 |
| Деталь: | WIRE BYPASS UNIT |
| Парткод: | 302GR46230 |
| Деталь: | WIRE BYPASS TRAY |
| Парткод: | 302GR46270 |
| Деталь: | JOINT,BYPASS PICKUP |
| Парткод: | 303A206131 |
| Деталь: | GEAR 16,PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | TORQUE LIMITER,BYPASS |
| Парткод: | 33906430 |
| Деталь: | FRICTION PLATE,BYPASS LEADING FEED |
| Парткод: | 34806490 |
| Деталь: | GEAR 18,CASSETTE |
| Парткод: | 34907141 |
| Деталь: | ARM,BYPASS PE |
| Парткод: | 3A206100 |
| Деталь: | HOLDER,RETARD |
| Парткод: | 3A206170 |
| Деталь: | MOUNT,BYPASS PE SWITCH |
| Парткод: | 3A206210 |
| Деталь: | UPPER PULLEY,BYPASS |
| Парткод: | 61706770 |
| Цена: | 1 900 ₽ |
| Деталь: | GEAR,16 BYPASS PULLEY |
| Парткод: | 66006810 |
| Деталь: | PIN,CASSETTE WORK PLATE |
| Парткод: | 66007310 |
| Деталь: | GEAR 30, FD EJECT IDLE |
| Парткод: | 72321350 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | EDGING, EDS-0607M(KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | MINI CLAMP, UAMS-02WL-0 (KITAGAWA) |
| Парткод: | M2105210 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | LABEL,CAUTION GEAR |
| Парткод: | 3A205010 |
| Деталь: | LABEL BYPASS JAM R |
| Парткод: | 302GR34170 |
| Деталь: | PLATE BYPASS HOLD |
| Парткод: | 2BL06890 |
| Деталь: | COVER CF |
| Парткод: | 303JT39020 |
| Деталь: | PARTS BYPASS UNIT |
| Парткод: | 302GR93111 |
| Деталь: | CLAW HEAT ROLLER |
| Парткод: | 2BL20080 |
| Деталь: | GEAR FIXING Z33 |
| Парткод: | 2BL20260 |
| Деталь: | STATIC ELIMINATOR PRESS |
| Парткод: | 2BL20330 |
| Деталь: | GEAR 49 HEAT ROLLER |
| Парткод: | 2FG20070 |
| Деталь: | BUSHING HEAT ROLLER |
| Парткод: | 2FG20190 |
| Деталь: | STOPPER HEAT ROLLER |
| Парткод: | 2FG20200 |
| Деталь: | BEARING HEAT ROLLER |
| Парткод: | 2FG20230 |
| Деталь: | GROUND PLATE FIXING |
| Парткод: | 2FG20280 |
| Деталь: | STATIC ELIMINATOR HEAT ROLLER |
| Парткод: | 302F725430 |
| Деталь: | THERMISTOR FIXING |
| Парткод: | 302FG20211 |
| Цена: | 2 100 ₽ |
| Деталь: | UPPER FRAME FUSER |
| Парткод: | 302GR25011 |
| Деталь: | LOWER FRAME FUSER |
| Парткод: | 302GR25022 |
| Деталь: | Guide Chute |
| Парткод: | 302GR25030 |
| Деталь: | FRONT FRAME FUSER |
| Парткод: | 302GR25040 |
| Деталь: | REAR FRAME FUSER |
| Парткод: | 302GR25050 |
| Деталь: | FRONT PRESSING PLATE |
| Парткод: | 302GR25060 |
| Деталь: | REAR PRESSING PLATE |
| Парткод: | 302GR25070 |
| Деталь: | STAY RIGHT FUSER |
| Парткод: | 302GR25080 |
| Деталь: | SPRING PRESSURE |
| Парткод: | 302GR25091 |
| Деталь: | PLATE GUIDE CHUTE |
| Парткод: | 302GR25100 |
| Деталь: | PIN LOWER FRAME |
| Парткод: | 302GR25161 |
| Деталь: | PLATE THERMO CUT |
| Парткод: | 302GR25180 |
| Деталь: | THERMISTOR FUSER NC |
| Парткод: | 302GR25190 |
| Деталь: | HOLDER THERMO CUT |
| Парткод: | 302GR25200 |
| Деталь: | PIN UPPER FRAME |
| Парткод: | 302GR25210 |
| Деталь: | SPRING THERMISTOR |
| Парткод: | 302GR25220 |
| Деталь: | PLATE ELIMINATOR |
| Парткод: | 302GR25230 |
| Деталь: | PIN GUIDE CHUTE |
| Парткод: | 302GR25241 |
| Деталь: | MOUNT THERMO CUT HOLDER |
| Парткод: | 302GR25250 |
| Деталь: | GROUND PLATE FUSER |
| Парткод: | 302GR25270 |
| Деталь: | SPRING CLAW |
| Парткод: | 302GR25280 |
| Деталь: | THERMOSTAT M FUSER |
| Парткод: | 302GR25290 |
| Цена: | 2 500 ₽ |
| Деталь: | PARTS,ROLLER HEAT SP |
| Парткод: | 302GR94270 |
| Деталь: | BEARING PRESSURE |
| Парткод: | 2C920330 |
| Деталь: | PARTS, HEATER 120 FUSER SP |
| Парткод: | 302GR94300 |
| Деталь: | PARTS, HEATER 230 FUSER SP |
| Парткод: | 302GR94310 |
| Деталь: | PARTS, HEATER 110 FUSER SP |
| Парткод: | 302GR94520 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | ADJUSTOR FUSER |
| Парткод: | 302GR02120 |
| Деталь: | FK-715 U |
| Парткод: | 302GR93051 |
| Деталь: | FK-715 E |
| Парткод: | 302GR93061 |
| Деталь: | FK-715 TW |
| Парткод: | 302GR93510 |
| Деталь: | PARTS,ROLLER PRESS SP |
| Парткод: | 302GR94280 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | SEAL WIRE |
| Парткод: | 2BL14480 |
| Деталь: | SPRING EXIT PULLEY |
| Парткод: | 2BL21070 |
| Деталь: | LEVER GUIDE CHANGE |
| Парткод: | 2BL21100 |
| Деталь: | ACTUATOR EXIT R |
| Парткод: | 2BL21120 |
| Деталь: | ACTUATOR EXIT L |
| Парткод: | 2BL21130 |
| Деталь: | PLATE EARTH EXIT F |
| Парткод: | 2BL21170 |
| Деталь: | PLATE EARTH EXIT R |
| Парткод: | 2BL21180 |
| Деталь: | BKT SOLENOID |
| Парткод: | 2BL21190 |
| Деталь: | PULLEY ONEWAY T30 |
| Парткод: | 2BL21211 |
| Деталь: | GEAR EXIT Z19 |
| Парткод: | 2BL21220 |
| Деталь: | PULLEY EXIT T30 |
| Парткод: | 2BL21230 |
| Деталь: | BELT EXIT P2M212 |
| Парткод: | 2BL21240 |
| Деталь: | SPRING ACTUATOR R |
| Парткод: | 2BL21250 |
| Деталь: | SPRING ACTUATOR L |
| Парткод: | 2BL21260 |
| Деталь: | SPRING FEED SHIFT |
| Парткод: | 2BL21270 |
| Деталь: | LEVER GUIDE CHANGE B |
| Парткод: | 2BL21370 |
| Деталь: | GEAR EXIT JOINT Z26S |
| Парткод: | 2BL21390 |
| Деталь: | SPRING EXIT JOINT |
| Парткод: | 2BL21400 |
| Деталь: | GEAR EXIT Z20 |
| Парткод: | 2BL21430 |
| Деталь: | SPRING EXIT CHANGE |
| Парткод: | 2BL21440 |
| Деталь: | PLATE EARTH CHANGE |
| Парткод: | 2BL21470 |
| Деталь: | CUT WASHER 6 |
| Парткод: | 2BL21510 |
| Деталь: | PULLEY EXIT C |
| Парткод: | 2BL21520 |
| Деталь: | COLLAR BELT |
| Парткод: | 2BL22580 |
| Деталь: | ROLLER EXIT |
| Парткод: | 302BL21021 |
| Деталь: | ROLLER FEED SHIFT |
| Парткод: | 302BL21031 |
| Деталь: | SHAFT EXIT PULLEY |
| Парткод: | 302BL21061 |
| Деталь: | GUIDE EXIT CHANGE |
| Парткод: | 302BL21081 |
| Деталь: | BKT DISCHARGER |
| Парткод: | 302BL21161 |
| Деталь: | JOINT EXIT |
| Парткод: | 302BL21202 |
| Деталь: | FRAME EXIT UP |
| Парткод: | 302GR28012 |
| Деталь: | FRAME EXIT LOW |
| Парткод: | 302GR28020 |
| Деталь: | PULLEY EXIT |
| Парткод: | 302GR28060 |
| Деталь: | SOLENOID FEED SHIFT |
| Парткод: | 302GR44160 |
| Деталь: | WIRE EJECT(C) |
| Парткод: | 302GR46140 |
| Деталь: | SWITCH,EJECT |
| Парткод: | 303BN27061 |
| Деталь: | STATIC ELIMINATOR,EJECT |
| Парткод: | 34821100 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | EDGING,EDS-0607L(KITAGAWA) |
| Парткод: | M2104390 |
| Деталь: | PIN EXIT |
| Парткод: | 302GR02860 |
| Деталь: | PARTS EXIT UNIT |
| Парткод: | 302GR93130 |
| Деталь: | PULLEY,PAPER FEED |
| Парткод: | 2AR07220 |
| Цена: | 1 600 ₽ |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | GUIDE FILM,SEPARATION PULLEY |
| Парткод: | 2AR07660 |
| Деталь: | BUSHING 6,REGISTRATION |
| Парткод: | 2BC06520 |
| Деталь: | PULLEY FEED A |
| Парткод: | 2BJ06010 |
| Цена: | 250 ₽ |
| Деталь: | PLATE LEADING FEED |
| Парткод: | 2BL07900 |
| Деталь: | SUPPORT PLATE FEED |
| Парткод: | 2BL07910 |
| Деталь: | SPRING SEPARATION |
| Парткод: | 2BL07990 |
| Деталь: | SHAFT,PAPER FEED |
| Парткод: | 302AR07251 |
| Деталь: | SHAFT,SEPARATION |
| Парткод: | 302AR07261 |
| Деталь: | SHAFT,LEADING FEED |
| Парткод: | 302AR07271 |
| Деталь: | UPPER HOUSING,PAPER FEED |
| Парткод: | 302FG07251 |
| Деталь: | LOWER HOUSING,PAPER FEED |
| Парткод: | 302FG07260 |
| Деталь: | WEIGHTLEADING FEED PULLEY |
| Парткод: | 302FG07271 |
| Деталь: | ACTUATOR,PAPER EMPTY |
| Парткод: | 302FG07290 |
| Деталь: | HOLDER,ACTUATOR |
| Парткод: | 302FG07300 |
| Деталь: | REINFORCEMENT PRIMARY PAPER FEED |
| Парткод: | 302FG07310 |
| Деталь: | STOPPER,SUPPORT PLATE |
| Парткод: | 302FG07320 |
| Деталь: | GROUND PLATE,PRIMARY PAPER FEED |
| Парткод: | 302FG07330 |
| Деталь: | LEVER SEPARATION RELEASE |
| Парткод: | 302GR06201 |
| Деталь: | WIRE PRIMARY FEED UNIT1 |
| Парткод: | 302GR46430 |
| Деталь: | TORQUE LIMITER,PAPER FEED |
| Парткод: | 33906070 |
| Деталь: | GEAR 16,PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | LOWER BUSHING,PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | GEAR 15 |
| Парткод: | 34922420 |
| Деталь: | PT.SENSOR GP1A73AJ00/ BK |
| Парткод: | 5FNXGP1A73A++02 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H01 |
| Деталь: | PARTS PRIMARY PAPER FEED UNIT |
| Парткод: | 302GR93020 |
| Деталь: | GUIDE DU FEED R |
| Парткод: | 302GR28071 |
| Деталь: | COVER EXIT FRONT |
| Парткод: | 302GR04110 |
| Деталь: | MOUNT HINGE |
| Парткод: | 2BL04220 |
| Деталь: | COVER EXIT LOW |
| Парткод: | 302BL04101 |
| Деталь: | MOUNT LEFT FRONT COVER |
| Парткод: | 2BJ04150 |
| Деталь: | COVER RIGHT TRAY |
| Парткод: | 302GR04280 |
| Деталь: | COVER REAR TRAY |
| Парткод: | 302GR04270 |
| Деталь: | COVER EXIT TOP |
| Парткод: | 302GR04120 |
| Деталь: | COVER ISU REAR |
| Парткод: | 302GR04231 |
| Деталь: | COVER ISU LEFT |
| Парткод: | 302GR04221 |
| Деталь: | COVER ISU RIGHT |
| Парткод: | 302GR04210 |
| Деталь: | LEVER CONT RELEASE |
| Парткод: | 2BL04200 |
| Деталь: | INNER RIGHT COVER |
| Парткод: | 302GR04320 |
| Деталь: | COVER TOP EJECT |
| Парткод: | 302GR04011 |
| Деталь: | COVER RIGHT FRONT |
| Парткод: | 302GR04030 |
| Деталь: | COVER CENTER FRONT |
| Парткод: | 302GR04021 |
| Деталь: | MAGNET CATCH |
| Парткод: | 2FB04220 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 2BL04330 |
| Деталь: | FRONT HINGE COVER P |
| Парткод: | 2BL04350 |
| Деталь: | PIN COVER HINGE |
| Парткод: | 302BL04191 |
| Деталь: | COVER LEFT FRONT LOW |
| Парткод: | 302GR04040 |
| Деталь: | COVER LEFT FRONT TOP |
| Парткод: | 302GR04050 |
| Деталь: | COVER LEFT SIDE TOP |
| Парткод: | 302GR04090 |
| Деталь: | COVER LEFT SIDE LOW |
| Парткод: | 302GR04100 |
| Деталь: | FRONT LEFT COVER |
| Парткод: | 302BL04111 |
| Деталь: | LID COVER LEFT |
| Парткод: | 302BL04301 |
| Деталь: | COVER RIGHT SIDE LOW |
| Парткод: | 302GR04080 |
| Деталь: | COVER REAR |
| Парткод: | 302GR04190 |
| Деталь: | COVER RIGHT SIDE TOP |
| Парткод: | 302GR04070 |
| Деталь: | PIN,TONER HOPPER |
| Парткод: | 3074315201 |
| Деталь: | PIN,OPTION |
| Парткод: | 302A126131 |
| Деталь: | TRAY SUB |
| Парткод: | 302GR04060 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302GR04410 |
| Деталь: | PIN COVER HINGE S |
| Парткод: | 302BL04841 |
| Деталь: | FRONT HINGE S COVER |
| Парткод: | 2BL04480 |
| Деталь: | LABEL SEP CLEANING |
| Парткод: | 302GR34181 |
| Деталь: | LABEL CONVEYING JAM |
| Парткод: | 302GR34190 |
| Деталь: | BRUSH CLEANER |
| Парткод: | 2BL16220 |
| Деталь: | GUIDE CLIP DISH |
| Парткод: | 302GR04310 |
| Деталь: | FILM HINGE |
| Парткод: | 2BL04880 |
| Деталь: | STOPPER PAPER SUB |
| Парткод: | 2BK04040 |
| Деталь: | PIN COVER |
| Парткод: | 302BL04411 |
| Деталь: | SHEET COVER ISU |
| Парткод: | 302GR04430 |
| Деталь: | SPONGE FRONT |
| Парткод: | 2BL06620 |
| Деталь: | CLIP DISH |
| Парткод: | 302GR04160 |
| Деталь: | MAGNET CLIP DISH |
| Парткод: | 302GR04370 |
| Деталь: | SEAL MAGNET |
| Парткод: | 302GR04380 |
| Деталь: | LABEL SW CAUTION EXP |
| Парткод: | 302GR34270 |
| Деталь: | LABEL SW CAUTION TW |
| Парткод: | 302GR34430 |
| Деталь: | COVER MAIN SW |
| Парткод: | 302GR04170 |
| Деталь: | FILTER VOC B |
| Парткод: | 302GR33090 |
| Деталь: | PARTS,EMBLEM ASSY 30 SP (30ppm) |
| Парткод: | 302GN94030 |
| Деталь: | PARTS,EMBLEM ASSY 40 SP (40ppm) |
| Парткод: | 302GP94030 |
| Деталь: | PARTS,EMBLEM ASSY 50 SP (50ppm) |
| Парткод: | 302GR94370 |
| Деталь: | SHEET OPE PROTECT |
| Парткод: | 302GR04450 |
| Деталь: | COVER ISU FRONT TOP |
| Парткод: | 302GR04240 |
| Деталь: | RETAINER MIRROR FRAME A |
| Парткод: | 302GR17262 |
| Деталь: | COVER OZONE |
| Парткод: | 302GR04250 |
| Деталь: | HOUSING OZONE COVER |
| Парткод: | 302GR04260 |
| Деталь: | LABEL CONTAINER |
| Парткод: | 302GR34200 |
| Деталь: | SPRING FRAME RETAINER |
| Парткод: | 302GR17360 |
| Деталь: | COVER TOTAL COUNTER |
| Парткод: | 2FG04020 |
| Деталь: | SHEET PROTECT |
| Парткод: | 302GR04440 |
| Деталь: | LABEL ENERGY STAR |
| Парткод: | 302G634070 |
| Деталь: | COVER ISU FRONT LOW |
| Парткод: | 302GR04200 |
| Деталь: | GROUND PLATE ISU OPE |
| Парткод: | 302GR04360 |
| Деталь: | LABEL SW CAUTION SET |
| Парткод: | 302GR34281 |
| Деталь: | Protection Plate |
| Парткод: | 302GR04420 |
| Деталь: | LABEL CAUTION HG |
| Парткод: | 302DC05120 |
| Деталь: | PARTS,DISPOSAL TANK,TB700 |
| Парткод: | 2BL93130 |
| Деталь: | GEAR 25 |
| Парткод: | 2AL06110 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GUIDE VERTICAL FEED |
| Парткод: | 2BL06110 |
| Деталь: | MOUNT C FEED DRIVE |
| Парткод: | 2BL06130 |
| Деталь: | GEAR Z42 FEED |
| Парткод: | 2BL06170 |
| Деталь: | GEAR Z28-P18 FEED |
| Парткод: | 2BL06180 |
| Деталь: | EARTH VERTICAL FEED |
| Парткод: | 2BL06220 |
| Деталь: | BELT CONVEYING |
| Парткод: | 2BL06320 |
| Деталь: | GUIDE B FEED |
| Парткод: | 2BL06330 |
| Деталь: | GEAR Z25 JOINT |
| Парткод: | 2BL06380 |
| Цена: | 370 ₽ |
| Деталь: | HOLDER FEED SWITCH |
| Парткод: | 2BL06450 |
| Деталь: | SPRING LEFT COVER |
| Парткод: | 2BL06460 |
| Деталь: | EARTH PUSH SWITCH |
| Парткод: | 2BL06940 |
| Деталь: | FRAME VERTICAL FEED A |
| Парткод: | 2FG06010 |
| Деталь: | MOUNT FEED DRIVE A |
| Парткод: | 2FG06020 |
| Деталь: | MOUNT FEED DRIVE B |
| Парткод: | 2FG06030 |
| Деталь: | GEAR Z21-Z36 FEED |
| Парткод: | 2FG06040 |
| Деталь: | SPRING FEED JOINT |
| Парткод: | 2FG06070 |
| Деталь: | COLLAR FEED JOINT |
| Парткод: | 2FG06120 |
| Деталь: | SPRING GUIDE FEED |
| Парткод: | 2FG06130 |
| Деталь: | ROLLER B FEED |
| Парткод: | 302BL06081 |
| Деталь: | ROLLER C FEED |
| Парткод: | 302BL06091 |
| Деталь: | JOINT FEED DRIVE |
| Парткод: | 302FG06051 |
| Деталь: | SHAFT FEED JOINT |
| Парткод: | 302FG06061 |
| Деталь: | CLUTCH FEED |
| Парткод: | 302GR44120 |
| Деталь: | SWITCH CONVEYING |
| Парткод: | 302GR44220 |
| Деталь: | WIRE CONVEYING |
| Парткод: | 302GR46260 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | GEAR 30,IDLE |
| Парткод: | 36222250 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | LOCK COVER R /40283V0068 A4 |
| Парткод: | 5MVX421DN003 |
| Деталь: | FILM MIDDLE FEED RAIL R |
| Парткод: | 2FG06220 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC03B1106+H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | FRONT RAIL FEED |
| Парткод: | 2BL06051 |
| Деталь: | REAR RAIL FEED |
| Парткод: | 2BL06061 |
| Деталь: | SHAFT LEFT COVER M |
| Парткод: | 302BL04521 |
| Деталь: | SPRING CONV OPEN |
| Парткод: | 302BL16232 |
| Деталь: | DUMPER LEFT COVER |
| Парткод: | 2BL06950 |
| Деталь: | STOPPER 7,CARTRIDGE |
| Парткод: | 33973300 |
| Деталь: | COVER CONNECTOR |
| Парткод: | 2BL06430 |
| Деталь: | FRONT GUIDE REGIST |
| Парткод: | 2BL06260 |
| Деталь: | PARTS,REGISTRATION CLEAN |
| Парткод: | 2BL93450 |
| Цена: | 4 000 ₽ |
| Деталь: | MOUNT REGIST SWITCH |
| Парткод: | 2BL06440 |
| Деталь: | SWITCH REGISTRATION |
| Парткод: | 2FG27110 |
| Деталь: | WIRE RESISTRATION |
| Парткод: | 302GR46240 |
| Деталь: | GEAR 18 |
| Парткод: | 36722860 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | RIGHT ROLLER REGIST |
| Парткод: | 302FG06211 |
| Деталь: | GUIDE A FEED |
| Парткод: | 2BL06020 |
| Деталь: | GEAR Z28 FEED |
| Парткод: | 2BL06150 |
| Деталь: | GEAR Z35-15 FEED |
| Парткод: | 2BL06160 |
| Деталь: | GEAR Z25 FEED |
| Парткод: | 2BL06190 |
| Деталь: | GROUND PLATE A FEED |
| Парткод: | 2BL06230 |
| Деталь: | GEAR Z42 BYPASS |
| Парткод: | 2BL06360 |
| Деталь: | FILM REGIST F |
| Парткод: | 2BL06480 |
| Деталь: | FILM REGIST FF |
| Парткод: | 2BL06970 |
| Деталь: | GUIDE MIDDLE FEED |
| Парткод: | 2FG06090 |
| Деталь: | PULLEY MIDDLE FEED |
| Парткод: | 2FG06110 |
| Деталь: | MOUNT BYPASS FEED |
| Парткод: | 2FG06160 |
| Деталь: | GROUND PLATE GUIDE A |
| Парткод: | 2FG06170 |
| Деталь: | FILM MIDDLE FEED |
| Парткод: | 2FG06200 |
| Деталь: | SHAFT FEED A |
| Парткод: | 302BL06921 |
| Деталь: | HOUSING FEED |
| Парткод: | 302FG06083 |
| Деталь: | SHAFT MIDDLE FEED |
| Парткод: | 302FG06101 |
| Деталь: | MOUNT MID FEED DRIVE |
| Парткод: | 302FG06151 |
| Деталь: | PULLEY MIDDLE FEED A |
| Парткод: | 302GR06010 |
| Деталь: | PULLEY MIDDLE FEED B |
| Парткод: | 302GR06020 |
| Деталь: | JOINT FEED |
| Парткод: | 302GR06030 |
| Деталь: | HOLDER WIRE |
| Парткод: | 302GR06220 |
| Деталь: | CLUTCH REGISTRATION |
| Парткод: | 302GR44140 |
| Деталь: | WIRE FEED 1 |
| Парткод: | 302GR46280 |
| Деталь: | PIN FEED |
| Парткод: | 302GR02330 |
| Деталь: | LABEL DRUM CAUTION J |
| Парткод: | 2FG05070 |
| Деталь: | LABEL DRUM CAUTION E1 |
| Парткод: | 2FG05080 |
| Деталь: | LABEL DRUM CAUTION E2 |
| Парткод: | 2FG05090 |
| Деталь: | LABEL DRUM CAUTION A |
| Парткод: | 2FG05100 |
| Деталь: | LABEL DRUM CAUTION CN |
| Парткод: | 2FG05110 |
| Деталь: | PARTS VERTICAL FEED UNIT |
| Парткод: | 302GR93160 |
| Деталь: | PARTS MIDDLE FEED UNIT |
| Парткод: | 302GR93150 |
| Деталь: | PARTS,GUIDE TRANSFER |
| Парткод: | 302GR94480 |
| Деталь: | DV-715 |
| Парткод: | 302GR93031 |
| Деталь: | FRONT ARM RAIL |
| Парткод: | 2BL14180 |
| Деталь: | REAR ARM RAIL |
| Парткод: | 2BL14190 |
| Деталь: | RAIL DLP |
| Парткод: | 2BL14200 |
| Деталь: | LEVER DLP |
| Парткод: | 2BL14210 |
| Деталь: | PIN LEVER DLP |
| Парткод: | 2BL14220 |
| Деталь: | GROUND PLATE RAIL |
| Парткод: | 2BL14350 |
| Деталь: | SEAL WIRE |
| Парткод: | 2BL14480 |
| Деталь: | PIN DLP RAIL |
| Парткод: | 302GR02852 |
| Деталь: | PIN,JAM REMOVEMENT DIAL |
| Парткод: | 3036006141 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC10B1112+H01 |
| Деталь: | COVER,PLATEN |
| Парткод: | 2A612800 |
| Деталь: | MAT,ORIGINAL HOLDER |
| Парткод: | 2A612810 |
| Деталь: | HINGE,ORIGINAL HOLDER |
| Парткод: | 2A612820 |
| Деталь: | STOPPER RELEASE SWITCH |
| Парткод: | 2C912630 |
| Деталь: | ORIGINAL POCKET |
| Парткод: | 60904280 |
| Деталь: | PEN KEYBOARD |
| Парткод: | 302GR05940 |
| Деталь: | HOLDER PEN |
| Парткод: | 302GR05950 |
| Деталь: | SET,PLATEN COVER TYPE D |
| Парткод: | 2CX82010 |
| Деталь: | PARTS,OPERATION PEN ASSY |
| Парткод: | 302GR94490 |
| Деталь: | Ремень подачи бумаги в автоподатчике документов |
| Парткод: | 303LL07531 |
| Цена: | 1 900 ₽ |
| Деталь: | Ролик захвата бумаги в узле автоматической подачи документов |
| Парткод: | 3H607020 |
| Цена: | 1 900 ₽ |
| Деталь: | FRONT FRAME |
| Парткод: | 302FG02042 |
| Деталь: | REAR FRAME |
| Парткод: | 302FG02051 |
| Деталь: | BASE |
| Парткод: | 302BL02031 |
| Деталь: | BASE MIDDLE |
| Парткод: | 302BL02041 |
| Деталь: | UPPER LEFT PLATE |
| Парткод: | 302GR02521 |
| Деталь: | UPPER FRONT FRAME |
| Парткод: | 302BJ02011 |
| Деталь: | UPPER REAR FRAME |
| Парткод: | 302GR02510 |
| Деталь: | UPPER RIGHT PIPE |
| Парткод: | 302GR02500 |
| Деталь: | LABEL RADIATION |
| Парткод: | 2BL05150 |
| Деталь: | LOWER LEFT REINFORCEMENT |
| Парткод: | 302FG02071 |
| Деталь: | LEFT RAIL CASSETTE |
| Парткод: | 302FG07033 |
| Деталь: | PULLEY,CASSETTE RAIL |
| Парткод: | 302FG07020 |
| Деталь: | PIN FRONT CASSETTE RAIL |
| Парткод: | 302GR02240 |
| Деталь: | PIN CASSETTE RAIL |
| Парткод: | 2FB06710 |
| Деталь: | MOUNT RUBBER ISU |
| Парткод: | 302GR02311 |
| Деталь: | ADJUSTOR ISU |
| Парткод: | 302GR02321 |
| Деталь: | BASE RUBBER,SCANNER SECTION |
| Парткод: | 2AV12280 |
| Деталь: | LOWER RIGHT REINFORCEMENT |
| Парткод: | 302GR02250 |
| Деталь: | LEVER LOCK CASSETTE |
| Парткод: | 302GR02221 |
| Деталь: | SPRING LEVER |
| Парткод: | 302GR02230 |
| Деталь: | MOUNT TRAY EJECT |
| Парткод: | 302GR02130 |
| Деталь: | UPPER PLATE FIXING |
| Парткод: | 302GR02550 |
| Деталь: | UPPER PLATE DRUM |
| Парткод: | 302GR02111 |
| Деталь: | LOWER PLATE CONT |
| Парткод: | 2BL02130 |
| Деталь: | LOWER BASE LSU |
| Парткод: | 2BL02050 |
| Деталь: | HOLDER,FULCRUM |
| Парткод: | 2BJ02121 |
| Деталь: | SUPPORT MOUNT DP |
| Парткод: | 302GR02300 |
| Деталь: | HANDLE MACHINE |
| Парткод: | 302GR02350 |
| Деталь: | SPRING BYPASS RET |
| Парткод: | 2BL06840 |
| Деталь: | BASE RUBBER |
| Парткод: | 2AR02180 |
| Деталь: | UPPER RIGHT PLATE |
| Парткод: | 302BL02122 |
| Деталь: | RIGHT HANDLE MACHINE |
| Парткод: | 302GR02340 |
| Деталь: | MOUNT RIGHT HANDLE |
| Парткод: | 2BL02150 |
| Деталь: | FILM HINGE |
| Парткод: | 2BL04880 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BL06590 |
| Деталь: | MOUNT HINGE S |
| Парткод: | 2BL04470 |
| Деталь: | GROUND PLATE MIDDLE |
| Парткод: | 2BL06410 |
| Деталь: | COVER,CASSETTE RAIL |
| Парткод: | 2AR07720 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | MOUNT REAR COVER |
| Парткод: | 302GR04290 |
| Деталь: | FULCRUM PLATE,MIDDLE TRAY |
| Парткод: | 2BJ02110 |
| Деталь: | GROUND PLATE ISU A |
| Парткод: | 302GR02531 |
| Деталь: | GROUND PLATE ISU B |
| Парткод: | 302GR02540 |
| Деталь: | MOUNT COVER R |
| Парткод: | 302GR04300 |
| Деталь: | MOUNT COVER L |
| Парткод: | 302GR04390 |
| Деталь: | PIN HANDLE |
| Парткод: | 302BL02171 |
| Деталь: | WIRE DEHUMIDIFIER HEATER JUNCTION |
| Парткод: | 302GR46740 |
| Деталь: | HEATER DEHUMIDIFIER 120 |
| Парткод: | 302FB25051 |
| Деталь: | HEATER DEHUMIDIFIER 240 |
| Парткод: | 302FB25060 |
| Деталь: | MOUNT,PAPER FEED DRAWER |
| Парткод: | 2AR07710 |
| Деталь: | WIRE PRIMARY FEED UNIT2 |
| Парткод: | 302GR46440 |
| Деталь: | RETAINING PIN,DRAWER |
| Парткод: | 3033927451 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H02 |
| Деталь: | LABEL L,HIGH TEMPERATURE CAUTION(E |
| Парткод: | 20305130 |
| Деталь: | PIN ROLLER RELEASE LEVER |
| Парткод: | 302FB16320 |
| Деталь: | Направляющая в узле регистрации, в сборе |
| Парткод: | 302GR94481 |
| Цена: | 3 000 ₽ |
Коды ошибок
C0030
C0060
C0070
C0130
C0140
C0150
C0160
C0170
C0180
C0600
C0610
C0630
C0640
C0700
C0800
C0830
C0870
C0880
C0920
C1010
C1020
C1030
C1040
C1100
C1110
C1120
C1130
C1800
C1900
C2000
C2250
C2500
C2600
C3100
C3200
C3210
C3300
C3310
C3500
C3900
C3910
C4000
C4010
C4200
C5300
C6000
C6020
C6030
C6050
C6400
C6410
C6420
C7300
C7400
C7410
C7800
C7810
C7900
C7910
C8020
C8030
C8050
C8060
C8070
C8140
C8170
C8180
C8190
C8210
C8220
C8230
C8300
C8310
C8320
C8330
C8340
C8350
C8360
C8440
C8460
C8500
C8510
C8800
C8900
C8910
C8920
C8930
C9000
C9040
C9050
C9060
C9070
C9080
F000
F010
F020
F030
F040
F041
F050
F060
F070
F080
F090
F14F
Описание
| Error code: | C0030 |
| Description: | FAX PWB system error |
| Causes: | The FAX processing cannot be continued due to the FAX firmware error. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. |
| Error code: | C0060 |
| Description: | Main PWB type mismatch error |
| Causes: | Poor contact in the connector terminals. |
| Remedy: | Check the connection of connector YC26 on the main PWB and relay board, and the continuity across the connector terminals. Repair if necessary. If the problem is not solved, run maintenance item U935 and return the relay board to the Service Administrative Division. |
| Error code: | C0070 |
| Description: | Toner motor |
| Causes: | Abnormal detection of FAX control PWB incompatibility in the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Remedy: | 1 Checking the FAX PWB The incompatible FAX PWB is installed. Install the FAX PWB for the applicable model. 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0130 |
| Description: | Backup memory read / write error |
| Causes: | The reading or writing into the flash memory is unavailable. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reconnect the connectors on the main PWB. At that time, fix or replace the wires if they are pinched by other parts or have any damage. When the issue is not resolved, replace the main PWB. |
| Error code: | C0140 |
| Description: | Backup memory (EEPROM) data problem • Reading data from EEPROM is abnormal. |
| Causes: | Data damage of EEPROM. |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | C0150 |
| Description: | Engine EEPROM reading / writing error |
| Causes: | 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing data. 2. The data read reading in 2 points mismatches 8 times continuously. 3. The read data and the write data mismatch 8 times continuously. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0160 |
| Description: | Engine PWB EEPROM data error |
| Causes: | The data read from the EEPROM is judged as abnormal. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing U021 The storage data in the EEPROM on the engine PWB is faulty. Execute U021. Executing U021 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. |
| Error code: | C0170 |
| Description: | Charger count error |
| Causes: | The values in one of the billing counters, life counter or the scanner counter mismatch between the main side and the engine side. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. Detaching and reattaching the main PWB 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0180 |
| Description: | Machine serial number mismatch |
| Causes: | The machine serial Nos. in the main PWB and the EEPROM on the engine PWB mismatch when turning the power on. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. Executing U004 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0600 |
| Description: | Scan problem |
| Causes: | DIMM installed incorrectly. Defective DIMM. |
| Remedy: | Check if the DIMM is inserted into the socket on the scanner main PCB correctly. Replace the DIMM and check for correct operation. |
| Error code: | C0610 |
| Description: | Lens drive problem |
| Causes: | Defective main PWB. |
| Remedy: | Replace the main PWB and check for correct operation. |
| Error code: | C0630 |
| Description: | DMA error |
| Causes: | DMA transmission of the image data does not finish within the certain time. |
| Remedy: | 1 Checking the connection 0 0 2 Checking the connection 0 0 3 Replacing the wire The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • DPCIS - DP relay PWB • DP relay PWB - Main PWB Wiring diagram 4 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. Detaching and reattaching the DP relay PWB 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0640 |
| Description: | Hard Disk error |
| Causes: | The HDD cannot be accessed properly. |
| Remedy: | 1 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 2 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 3 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 4 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0700 |
| Description: | Side feeder EEPROM error • An error occurs in EEPROM (U4) data read or write for the side feeder main PWB. |
| Causes: | Defective side feeder main PWB. |
| Remedy: | Replace the side feeder main PWB. |
| Error code: | C0800 |
| Description: | Image processing error |
| Causes: | The print sequence jam (J010x) was detected 2 times continuously. |
| Remedy: | 1 Checking the image data The image data is faulty. When this issue occurs only when handling the certain image data, check if the image data is faulty. 2 Checking the situation The printing operation of the certain file is faulty. Acquire the jobs log if the phenomenon can be reproduced by specifying the job when the error was detected.` 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. Detaching and reattaching the main PWB 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0830 |
| Description: | FAX PWB flash program area checksum error |
| Causes: | The program stored in the flash memory on the FAX PWB is broken so it cannot perform. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 2 Checking the FAX PWB The FAX PWB is not properly connected. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0870 |
| Description: | PC FAX Image data transmission error |
| Causes: | Data was not properly transmitted even if the specified times of retry were made when the large volume data is transmitted between the FAX PWB and the main PWB. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 3 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 6 Executing U024 The data stored in the SSD is faulty. Execute U024 [SSD Format]. Executing U024 |
| Error code: | C0880 |
| Description: | Program archive problem (optional fax) When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0920 |
| Description: | 1st drawer lift |
| Causes: | The backup data could not be stored since the file system of the flash memory is faulty. |
| Remedy: | 1 Initializing the fax FAX control values are incorrect Execute U600 to initialize the FAX. Executing U600 2 Checking the FAX PWB The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Reinstalling the FAX PWB The FAX PWB is not properly installed. Reinstall the FAX PWB. FAX Installation Guide 4 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 5 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C1010 |
| Description: | Lift motor 1 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 1 is installed. 2. The lock-up signal is not released for 1s after lift motor 1 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift motor 1 - Feed PWB Wiring diagram 4 Checking lift motor 1 Lift motor 1 is faulty. Check the operation of lift motor 1, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 1 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 1 is not properly attached or faulty. Reattach lift sensor 1. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1020 |
| Description: | Lift motor 2 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 2 is installed. 2. The lock-up signal is not released for 1s after lift motor 2 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Lift motor 2 - Feed PWB Wiring diagram 4 Checking lift motor 2 Lift motor 2 is faulty. Check the operation of lift motor 2, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 2 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 2 is not properly attached or faulty. Reattach lift sensor 2. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1030 |
| Description: | Lift motor 3 error • When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on. This error is detected four times successively. • During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 3. Defective lift motor 3. Poor contact of lift motor 3 connector terminals. Defective lift limit switch 3. Poor contact of lift limit switch 3 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 3. Replace lift motor 3. Defective lift motor 3. Check for continuity across the coil. If none, replace lift motor 3. Poor contact of lift motor 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 3. Run maintenance item U031 and turn lift limit switch 3 on and off manually. Replace lift limit switch 3 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB |
| Error code: | C1040 |
| Description: | Lift motor 4 error • When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on. This error is detected four times successively. • During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 4. Defective lift motor 4. Poor contact of lift motor 4 connector terminals. Defective lift limit switch 4. Poor contact of lift limit switch 4 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 4. Replace lift motor 4. Defective lift motor 4. Check for continuity across the coil. If none, replace lift motor 4. Poor contact of lift motor 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 4. Run maintenance item U031 and turn lift limit switch 4 on and off manually. Replace lift limit switch 4 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB. |
| Error code: | C1100 |
| Description: | PF lift motor 1 error |
| Causes: | [The right cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because one of the phenomena below. 1. PF lift sensor 1 does not turn on when passing 23s while PF lift motor 1 turns on for the first time after inserting the cassette. 2. PF lift sensor 1 does not turn on when passing 2s while PF lift motor 1 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 1 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 1 - PF main PWB Wiring diagram 4 Checking PF lift motor 1 PF lift motor 1 is faulty. Replace PF lift motor 1. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift sensor 1 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 1 is not properly attached or faulty. Reattach PF lift sensor 1. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1110 |
| Description: | PF lift motor 2 error |
| Causes: | [The left cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because of one of the phenomena below. 1. PF lift sensor 2 does not turn on when passing 23s while PF lift motor 2 turns on for the first time after inserting the cassette. 2. PF lift sensor 2 does not turn on when passing 2s while PF lift motor 2 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 2 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 2 - PF main PWB Wiring diagram 4 Replacing PF lift motor 2 PF lift motor 2 is faulty. Replace PF lift motor 2. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •PF lift sensor 2 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 2 is not properly attached or faulty. Reattach PF lift sensor 2. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1120 |
| Description: | PF left lift position problem (optional 3000-sheet paper feeder) Level switch 1 does not turn on within 30 s of PF lift motor 2 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 1. Defective PF lift motor 2. The PF left lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 1. Check if YC5-4 on the PF main PWB goes low when level switch 1 is turned off. If not, replace PF lift switch 1. Defective PF lift motor 1. Check for continuity across the coil. If none, replace PF lift motor 1. The PF left lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C1130 |
| Description: | PF right lift position problem (optional 3000-sheet paper feeder) Level switch 2 does not turn on within 30 s of PF lift motor 1 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 2. Defective PF lift motor 1. The PF right lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 2. Check if YC5-7 on the PF main PWB goes low when level switch 2 is turned off. If not, replace PF lift switch 2. Defective PF lift motor 2. Check for continuity across the coil. If none, replace PF lift motor 2. The PF right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C1800 |
| Description: | Large capacity feeder communication error Condition: When turning the main power off and on while disconnecting the connector of the cable from the side multi feeder, this service call error does not reappear. (It is caused by the large capacity feeder.) |
| Causes: | The communication error was detected 10 times continuously. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the large capacity feeder firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB (Large capacity feeder) - PF main PWB (Side multi feeder) • PF main PWB (Side multi feeder) - Engine PWB Wiring diagram 3 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Large capacity feeder) Detaching and reattaching the PF main PWB (Large capacity feeder) 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1900 |
| Description: | Large capacity feeder EEPROM error Condition: When outputting Event Log after turning the main power off and on while disconnecting the connector of the cable from the side multi feeder, this service call error is not recorded. (It is caused by the large capacity feeder.) (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously when writing. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the large capacity feeder firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB (Large capacity feeder) - PF main PWB (Side multi feeder) • PF main PWB (Side multi feeder) - Engine PWB Wiring diagram 3 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Large capacity feeder) Detaching and reattaching the PF main PWB (Large capacity feeder) 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2000 |
| Description: | Drive motor problem Stable OFF is detected for 1 s continuously after drive motor stability. The drive motor is not stabilized in 6 s since the motor is activated. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective drive motor. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective drive motor. Replace the drive motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | C2250 |
| Description: | Cleaning motor error • LOCK signal remains high for 1 s, 200 ms after the cleaning motor has turned on. |
| Causes: | Poor contact in the drive motor connector terminals. Defective cleaning motor rotation control circuit. Defective drive transmission system. Defective engine PWB. |
| Remedy: | Poor contact in the drive motor connector terminals. Check the connection of connector YC5 on the engine PWB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective cleaning motor rotation control circuit. Replace the cleaning motor. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective engine PWB. Replace the engine PWB. |
| Error code: | C2500 |
| Description: | Feed motor error |
| Causes: | The ready signal is not at the L level after passing 2s since the feed motor drive was started. |
| Remedy: | 1 Checking the feed motor The operation of the feed motor is faulty. Execute U030 [Feed] to check the feed motor operation. Check if the drive gears rotate and have no excessive load, and apply the grease (EM-LP, Part no: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the feed motor The feed motor is faulty. Replace the feed motor. 4 Replacing the feed drive unit The feed drive unit is faulty. Replace feed drive unit. Detaching and reattaching the Feed Drive Unit 5 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 6 Firmware upgrade The firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB 8 Replacing the feed image PWB The power can`t be supplied to the feed drive PWB. Replace the feed image PWB. |
| Error code: | C2600 |
| Description: | PF feed motor error |
| Causes: | The ready signal is not at the L level (stable rotation) after passing 1s since the PF feed motor drive started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected, or it is faulty. Execute U247 [2PF] or [LCF] > [Motor On] to check the paper feed operation. If the PF feed motor does not operate properly, reconnect the connector of the motor. Check if the PF feed roller and the drive gears rotate smoothly and have no excessive load, apply the grease (EM-50LP, Part no.: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF PWB • PF PWB - Engine PWB (Drawer connector between the paper feeder and the main unit) Service Manual - Section 8 `PWBs` 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF Drive Unit 4 Firmware upgrade The engine firmware or the PF firmware is faulty. Upgrade the engine firmware and the PF firmware to the latest version. Firmware Update 5 Replacing the PF PWB The PF PWB is faulty. Replace the PF PWB. Detaching and reattaching the PF PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C3100 |
| Description: | Carriage error |
| Causes: | When turning the power on or finishing originals scan through the scanner, the alignment of the home position sensor (turning on / off the sensor) fails and the error is detected. Then, the error is detected twice continuously even the initial operation is executed. |
| Remedy: | 1 Unlocking the scanner mirror frame The scanner mirror frame is not unlocked. Unlock the scanner mirror frame (lamp unit assy). Unlocking the scanner mirror frame 2 Checking the scanner movement A load is applied to the scanner movement. Check the operation of the lamp by U073 or manually moving it. If there is an excess load, check if there are any foreign objects on the optical wire or optical wire drum and clean it. After that, apply grease on the scanner rail. Detaching and reattaching the scanner wires 3 Checking the scanner wires The scanner wires are dirty or come off. Clean and reattach the scanner wires. Detaching and reattaching the scanner wires 4 Checking the scanner motor The scanner motor is faulty. Reattach the scanner motor and reconnect the connector. If not repaired, replace it. 5 Checking the belt tension of the scanner motor A load is applied to the scanner movement since the belt tension is improper. Adjust the scanner motor belt tension properly. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Scanner motor - Engine PWB Wiring diagram 7 Checking the home position sensor The home position sensor is not properly attached. Reattach the home position sensor. 8 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Home position sensor - Engine PWB Wiring diagram 9 Replacing the home position sensor The home position sensor is faulty. Replace the home position sensor. 10 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3200 |
| Description: | LED lamp startup error |
| Causes: | The white reference data acquired by lighting the LED lamp at the initial operation does not reach the specified value. Or, the light amount detected by the CCD PWB is not enough. (2 or more LED lamps do not light. The light does not reach the CCD PWB due to condensation.) |
| Remedy: | 1 Checking the LED lamp The LED lamp does not light. Execute U061 [CCD] and check if the LED lamp is lit. If not, replace the lamp unit. After that, execute U411 [Table(ChartA)]. Detaching and reattaching the lamp unit 2 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB • LED PWB - CCD PWB Wiring diagram 3 Checking the mirror The mirror or lens is frosted due to condensation. Clean the mirrors. If the condensation at the scanner section is resolved naturally by opening the document processor or the platen cover, turn the power switch off and on. 4 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3210 |
| Description: | CIS lamp error |
| Causes: | Input data did not exceed the threshold for 5s when the CIS lamp was ON. |
| Remedy: | 1 Releasing the partial operation The partial operation is executed. Execute resetting the partial operation at U906. Executing U906 2 Checking the DPCIS The CIS lamp does not light. Execute U061 [CIS] and check if the CIS lamp is lit. If not, replace the DPCIS and execute U411. Detaching and reattaching the CIS 3 Cleaning the CIS glass and the CIS roller The CIS glass or the CIS roller is dirty. Clean the CIS glass and the CIS roller. 4 Checking the DPSHD PWB The DPSHD PWB is not properly connected. Reconnect the DPSHD PWB to the DPCIS. 5 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • DPSHD PWB - DP relay PWB • DP relay PWB - Main PWB • DP relay PWB - DP main PWB • DP main PWB - Engine PWB Wiring diagram 6 Firmware upgrade The firmware is not the latest version. Upgrade the DP firmware to the latest version. Firmware Update 7 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. 8 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. 9 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 10 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. Detaching and reattaching the DP main PWB 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3300 |
| Description: | CCD AGC error (For the internal count) |
| Causes: | Brightness of the LED lamp is darker while one of the LED lamp does not turn on or brighter than expected when processing the AGC for the CCD lamp. |
| Remedy: | 1 Checking the LED lamp The LED lamp is faulty. Check if the LED lamp lights by executing U061 [CCD]. If it does not light, replace the lamp unit and execute U411 [Table (ChartA) ]. Detaching and reattaching the lamp unit 2 Cleaning the backside of the contact glass The white reference sheet is dirty. Clean the white reference sheet at the backside of the contact glass. Detaching and reattaching the contact glass 3 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is peeled off, deformed or the FFC is broken, replace the FFC. • LED PWB - CCD PWB • CCD PWB - Engine PWB Wiring diagram 4 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 5 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3310 |
| Description: | CIS AGC error (For the internal count) |
| Causes: | The CIS could not get the normal white reference value after the AGC retry. |
| Remedy: | 1 Releasing the partial operation The partial operation is executed. Execute resetting the partial operation at U906. Executing U906 2 Cleaning the CIS glass and the CIS roller The CIS glass or the CIS roller is dirty. Clean the CIS glass and the CIS roller. 3 Firmware upgrade The firmware is not the latest version. Upgrade the DP firmware to the latest version. Firmware Update 4 Checking the DPSHD PWB The DPSHD PWB is not properly connected. Reconnect the DPSHD PWB to the DPCIS. 5 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. 6 Replacing the DPCIS The DPCIS is faulty. Replace the DPCIS, and then execute U091 and U411. Detaching and reattaching the DPCIS 7 Checking the connection The connector is not properly connected. Or, the SATA cable is faulty. Clean the terminal of the following SATA cable connector and reconnect the connectors. If there is no continuity, replace the SATA cable. • DPSHD PWB - DP relay PWB • DP relay PWB - Main PWB Wiring diagram 8 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. 9 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C3500 |
| Description: | Communication error between the scanner and the ASIC |
| Causes: | The communication error is detected during the communication between the scanner ASIC and the scanner CPU. |
| Remedy: | 1 Resetting the main power ASIC does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3900 |
| Description: | Scanner backup memory read / write error (Engine EEPOM) |
| Causes: | The read-back value of the engine EEPROM differs. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. Detaching and reattaching the EEPROM 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3910 |
| Description: | Backup memory read/write error (scanner PWB) • Data in the specified area of the backup memory does not match the specified values. |
| Causes: | Problem with the backup memory data. Defective scanner PWB. |
| Remedy: | Problem with the backup memory data. Run maintenance item U022 to initialize the backup memory data. Defective scanner PWB. If the C3910 is displayed after initializing the backup memory, replace the main PWB and check for correct operation. |
| Error code: | C4000 |
| Description: | Polygon motor synchronization problem • The revolution does not reach the stable speed within 20 s of the START signal. |
| Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
| Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
| Error code: | C4010 |
| Description: | Polygon motor steady-state problem • The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized. |
| Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
| Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
| Error code: | C4200 |
| Description: | BD steady-state problem • ASIC of the main PWB detects a BD error A for 4000 ms after the polygon motor rotation has been stabilized. |
| Causes: | Defective laser diode. Defective polygon motor. Defective main PWB. Poor contact in connector terminals. |
| Remedy: | Defective laser diode. Replace the laser scanner unit. Defective polygon motor. Replace the laser scanner unit. Defective main PWB. Replace the main PWB and check for correct operation. Poor contact in connector terminals. Check the connection of connector YC8 on the main PWB and the continuity across the connector terminals. Repair or replace if necessary. |
| Error code: | C5300 |
| Description: | Cleaning lamp broken detection • The current at the correct level is not detected when ASIC (U8) on the engine controller PCB generates the signal to activate the cleaning lamp. |
| Causes: | Defective engine controller PCB. Defective drum unit (cleaning lamp or drum PCB). Defective harness between engine controller PCB and drum unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the drum unit. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C6000 |
| Description: | IH heating error 1 |
| Causes: | The fuser center thermistor temperature does not reach 100°C / 212°F when passing 60s since warm-up starts. Or, the ready display temperature is not detected when passing 420s since the fuser center thermistor temperature reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Executing U169 The IH setting mismatches the power source specification. Set the fuser destination same as the IH PWB voltage at U169. Executing U169 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature cannot be detected properly due to the broken thermostat or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6020 |
| Description: | Fuser center thermistor high temperature error |
| Causes: | The fuser center thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6030 |
| Description: | Fuser center thermistor broken |
| Causes: | The output from the fuser center thermistor is under 20°C / 68°F level during warm-up. Or, the temperature detected at the fuser center thermistor does not change for 10s after turning the fuser heater on. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6050 |
| Description: | Fuser center thermistor low temperature error |
| Causes: | The fuser center thermistor detects less than 100°C / 212°F for 1s after warm-up, or during print or standby. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 11 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit |
| Error code: | C6400 |
| Description: | Zero-cross signal error • The engine PWB does not detect the zero-crossing signal (Z CROSS SIG) for 5 s. |
| Causes: | Poor contact in the connector terminals. Defective DC power source PWB. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and YC6 on the DC power source PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective DC power source PWB. Check if the zero-crossing signal is output from YC6-3 on the DC power source PWB. If not, replace the DC power source PCB. Defective engine PWB. Replace the engine PWB if C6400 is detected while YC6-3 on the DC power source PWB outputs the zero-crossing signal. |
| Error code: | C6410 |
| Description: | Fuser unit type mismatch error |
| Causes: | "Unit Identification" code in the EEPROM of the fuser unit does not match the main unit. The fuser unit for other model is installed. |
| Remedy: | 1 Replacing the fuser unit The fuser unit for other models is installed. Install the fuser unit for the applicable models. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB Wiring diagram 5 Replacing the fuser unit The fuser unit is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6420 |
| Description: | Fuser unit fuse cut problem The fuse cannot be cut, When replacing the fuser unit, the fuse cannot be cut in 3 s after the fuse cut signal is turned on. |
| Causes: | Poor contact in the connector terminals. Fuser unit connector inserted incorrectly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC1 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. |
| Error code: | C7300 |
| Description: | Toner hopper problem • During toner replenishment after toner empty has been detected, toner empty could not be cleared in 3 times of 360 s. |
| Causes: | Defective toner level detection sensor. Poor contact in the toner level detection sensor connector terminals. |
| Remedy: | Defective toner level detection sensor. Replace the toner level detection sensor. Poor contact in the toner level detection sensor connector terminals. Check the connection of connectors YC2 and YC5 on the deck PWB and YC3 on the engine PWB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Error code: | C7400 |
| Description: | Developing unit connector insertion problem Absence of the developing unit is detected. |
| Causes: | Developing unit connector inserted incorrectly. Defective developing unit connector. |
| Remedy: | Developing unit connector inserted incorrectly. Reinsert the developing unit connector if necessary. Defective developing unit connector. Replace the developing unit. |
| Error code: | C7410 |
| Description: | Drum unit connector insertion problem Absence of the drum unit is detected. |
| Causes: | Drum unit connector inserted incorrectly. Defective drum unit connector. |
| Remedy: | Drum unit connector inserted incorrectly. Reinsert the drum unit connector if necessary. Defective drum unit connector. Replace the drum unit. |
| Error code: | C7800 |
| Description: | Outer thermistor broken (For the internal count) |
| Causes: | The external temperature sensor (external thermistor) cannot be accessed. No response is received from the external thermistor 5 times continuously for 5ms or more when accessing the external thermistor. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Room temperature sensor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Replacing the external temperature sensor The external temperature sensor is faulty. Replace the external temperature sensor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7810 |
| Description: | Short-circuited external thermistor • The thermistor input value is 0.5 V or less. |
| Causes: | Poor contact in the connector terminals. Defective humidity sensor. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC13 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective humidity sensor. Replace the humidity sensor. Defective engine PWB. Replace the engine PWB. |
| Error code: | C7900 |
| Description: | Drum EEPROM error Reading from or writing to EEPROM cannot be performed. |
| Causes: | Poor contact in the connector terminals. Defective drum unit. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective drum unit. Replace the drum unit. |
| Error code: | C7910 |
| Description: | Developing unit EEPROM error Reading from or writing to EEPROM cannot be performed. |
| Causes: | Poor contact in the connector terminals. Defective developing unit. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective developing unit. Replace the developing unit. |
| Error code: | C8020 |
| Description: | Punch motor error 2 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position is not aligned within 3s when initializing the home position or standby. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8030 |
| Description: | Punch motor error 3 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position detection does not turn off within 50ms when initializing the home position. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8050 |
| Description: | Punch shift motor error 2 Object: 100-sheet staple finisher |
| Causes: | The paper edge cannot be detected if driving the motor by the specified distance (30mm) when detecting the paper edge. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit does not move manually, repair the position where restricts the operation. 2 Checking the PH cam drive parts The PH cam drive parts are not attached properly or faulty. Reattach the punch cam drive components. Replace it if not repaired 3 Checking the connection The connector is not properly connected. Or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EPunch shift motor - PH PWB EPaper edge sensor 1,2 - PH PWB EPH PWB- DF PWB 4 Replacing the punch shift motor The punch shift motor is faulty. Execute U240 mMotorn > mPunch Moven Replace the punch shift motor if it does not operate properly. 5 Checking the paper edge sensors 1, 2 Paper edge sensors 1, 2 are not properly attached or faulty. Execute U241 mPunchn > mEdge Face1/2n Reattach the paper edge sensors 1, 2 if they do not operate properly. Replace the paper edge sensors 1, 2 if not repaired. 6 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. 7 Replacing PH PWB PH PWB is faulty. Replace PH PWB. 8 Replacing DF PWB DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. |
| Error code: | C8060 |
| Description: | Paper conveying belt motor 2 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 2 does not turn off within 1.5 s. Paper conveying belt home position sensor 2 does not turn on within 1.5 s. |
| Causes: | Poor contact in the connector terminals. Defective paper conveying belt home position sensor 2. Defective paper conveying belt motor 2. Defective PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 on the inner tray PWB and the connector on paper conveying belt motor 2, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper conveying belt home position sensor 2. Replace paper conveying belt home position sensor 2. Defective paper conveying belt motor 2. Replace paper conveying belt motor 2. Defective PWB. Replace the inner tray PWB or finisher main PWB and check for correct operation. |
| Error code: | C8070 |
| Description: | Inner tray communication error (optional 3000-sheet document finisher) Communication with the inner tray is not possible although the connection is detected. |
| Causes: | Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 and YC24 on the finisher main PWB and the connector YC1 and YC4 on the inner tray PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Replace the inner tray PWB or finisher main PWB and check for correct operation. |
| Error code: | C8140 |
| Description: | Main tray error 1 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 does not turn on when passing 30s while lifting up the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8170 |
| Description: | DF side registration motor 1 error 1 Object: 4000-sheet finisher |
| Causes: | The home position cannot be detected after passing 3s when relocating to the home position. |
| Remedy: | 1 Checking the front DF side registration guide The front DF side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. 5 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8180 |
| Description: | DF side registration motor 1 error 2 Object: 4000-sheet finisher |
| Causes: | J6810/J6811/J6812 (Front DF side registration jam) was detected 2 times continuously. |
| Remedy: | 1 Checking the front DF side registration guide The front side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive components. 3 Replacing the front DF side registration guide drive components The front DF side registration guide drive components are faulty. Replace the front DF side registration guide drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB 5 Checking DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. Executing U240 6 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8190 |
| Description: | DF side registration motor 2 error 1 Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while executing the operation of returning to the home position. |
| Remedy: | 1 Checking the rear DF side registration guide The rear DF side registration guide is not assembled properly. If the rear DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear DF side registration guide drive components The rear DF side registration guide drive parts are not properly attached or faulty. Reattach the rear DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 2 - DF main PWB • DF side registration sensor 2 - DF main PWB 4 Replacing DF side registration motor 2 DF side registration motor 2 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking DF side registration sensor 2 DF side registration sensor 2 is not properly attached or faulty. Reattach DF side registration sensor 2 and execute U241 [Finisher] > [Width Tail HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8210 |
| Description: | DF staple motor front/rear error Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while returning to the home position at the initial operation. |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple unit is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the DF staple unit drive components The DF staple unit drive parts are not properly attached or faulty. Reattach the DF staple unit drive parts. If not repaired, replace the parts. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple motor - DF main PWB • DF staple sensor - DF main PWB Wiring diagram 4 Replacing the DF staple motor The DF staple motor is faulty. Execute U240 [Motor] > [Staple]. If the DF staple motor does not properly operate, replace the DF staple unit. 5 Checking the DF staple sensor The DF staple sensor is not properly attached or faulty. Reattach the DF staple sensor. Then, replace the DF staple unit if the sensor is not fixed. Detaching and reattaching the DF staple unit 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8220 |
| Description: | Document finisher* front clincher problem • During initialization, the front clincher is not detected in the home position within 500 ms after the front clincher returns to the home position. JAM90 is indicated the first time this problem occurs. If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front clincher. • When the front clincher is operated from the home position, the front clincher home position sensor does not turn off within 500 ms. |
| Causes: | Loose connection of the front clincher motor connector. Malfunction of the front clincher motor. Malfunction of the front clincher home position sensor. Loose connection of the front clincher home position sensor connector. Defective finisher main PWB. |
| Remedy: | Loose connection of the front clincher motor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Malfunction of the front clincher motor. Replace the front clincher motor and check for correct operation. Malfunction of the front clincher home position sensor. Replace the front clincher home position sensor and check for correct operation. Loose connection of the front clincher home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8230 |
| Description: | DF staple motor error Object: 4000-sheet finisher |
| Causes: | J7000 (DF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple cannot operate manually without paper jam, repair the part that restricts the DF staple. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple unit - DF main PWB Wiring diagram 3 Replacing the DF staple unit The DF staple unit is faulty. Replace the DF staple unit. Detaching and reattaching the DF staple unit 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8300 |
| Description: | Main program error / Folding unit communication error Object: 4000-sheet finisher + Folding unit |
| Causes: | The main program of the folding unit is faulty when turning the power on. The communication error appears 10 times continuously after finishing the folding unit firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the BF firmware and the DF firmware to the latest version. Firmware Update 3 Checking the BF set switch The BF set switch is not properly attached. Reattach the BF set switch. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 5 Replacing the BF set switch The BF set switch is faulty. Execute U241 [Booklet] > [Set]. If the BF set switch does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8310 |
| Description: | BF side registration motor 2 error Object: 4000-sheet finisher + Folding unit |
| Causes: | BF side registration sensor 2 does not turn on after passing 1s during the initial operation. |
| Remedy: | 1 Checking the upper BF side registration guide The upper BF side registration guide is not assembled properly. If the upper BF side registration guide is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the upper BF side registration guide drive components The upper BF side registration guide drive parts are not properly attached or faulty. Reattach the upper BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 2 - BF main PWB • BF side registration sensor 2 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 2 BF side registration motor 2 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 2 BF side registration sensor 2 is not properly attached or faulty. Reattach BF side registration sensor 2 and execute U241 [Booklet] > [Width Down HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8320 |
| Description: | BF adjustment motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | At the initialization, turning on of the BF adjustment sensor is not detected after 2.5s passes. |
| Remedy: | 1 Checking the BF shift belt The BF shift belt is not assembled properly. If the BF shift belt is not operated manually, repair the part that restricts the operation. 2 Checking the BF shift belt drive components The BF shift belt drive parts are not properly attached or faulty. Reattach the BF shift belt drive parts. Reattach it if the belt comes off. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF adjustment motor 1, 2 - BF main PWB • BF adjustment sensor 1, 2 - BF main PWB Wiring diagram 4 Replacing BF adjustment motor 1, 2 BF adjustment motor 1 or 2 is faulty. Execute U240 [Booklet] > [Bundle Down] or [Bundle Up]. If BF adjustment motor 1 or 2 does not properly operate, replace them. Executing U240 5 Checking BF adjustment sensor 1, 2 BF adjustment sensor 1 or 2 is not properly attached or faulty. Reattach BF adjustment sensor 1 or 2 and execute U241 [Booklet] > [Width Down HP] or [Bundle Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8330 |
| Description: | BF blade motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | The BF blade sensor does not turn on after passing 3s during the initial operation. |
| Remedy: | 1 Checking the BF blade The BF blade is not assembled properly. If the BF blade is not operated manually, repair the part that restricts the operation. 2 Checking the BF blade drive components The BF blade drive parts are not properly attached or faulty. Reattach the BF blade drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF blade motor - BF main PWB • BF blade sensor - BF main PWB Wiring diagram 4 Replacing the BF blade motor The BF blade motor is faulty. Execute U240 [Booklet] > [Blade]. If the BF blade motor does not properly operate, replace it. Executing U240 5 Checking the BF blade sensor The BF blade sensor is faulty. Reattach the BF blade sensor and reinsert the connector. Next, execute U241 [Booklet] > [Blade HP]. If it does not properly operate, replace the sensor. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8340 |
| Description: | BF staple motor error 1 Object: 4000-sheet finisher + Folding unit |
| Causes: | J7600 (BF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
| Remedy: | 1 Checking the BF staple unit The BF staple unit is not assembled properly. If the BF staple unit is not operated manually, repair the part that restricts the operation. 2 Checking the BF staple unit drive components The BF staple unit drive parts are not properly attached or faulty. Reattach the BF staple unit drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF staple unit - BF main PWB Wiring diagram 4 Replacing the BF staple motor The BF staple motor is faulty. Execute U240 [Booklet] > [Staple]. If the BF staple motor does not properly operate, replace it. Executing U240 5 Replacing the BF staple unit The BF staple unit is faulty. Replace the BF staple unit. 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8350 |
| Description: | BF side registration motor 1 error Object: 4000-sheet finisher + Folding unit |
| Causes: | BF side registration sensor 1 does not turn on after passing 1s during the initial operation. |
| Remedy: | 1 Checking the lower BF side registration guide The lower BF side registration guide is not assembled properly. If the lower BF side registration guide is not operated manually, repair the part that restricts the operation. 2 Checking the lower BF side registration guide drive components The lower BF side registration guide drive parts are not properly attached or faulty. Reattach the lower BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 1 - BF main PWB • BF side registration sensor 1 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 1 BF side registration motor 1 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 1 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 1 BF side registration sensor 1 is not properly attached or faulty. Reattach BF side registration sensor 1 and execute U241 [Booklet] > [Width Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8360 |
| Description: | BF main motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | The lock-up signal was detected for 1s continuously during the motor operation. |
| Remedy: | 1 Checking the BF conveying roller The BF conveying roller is not assembled properly. If the BF conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the BF conveying roller drive parts The BF conveying roller drive parts are not properly attached or faulty. Reattach the BF conveying roller drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main motor - BF main PWB Wiring diagram 4 Replacing the BF main motor The BF main motor is faulty. Execute U240 [Booklet] > [Folding]. If the BF main motor does not properly operate, replace it. Executing U240 5 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8440 |
| Description: | Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range. |
| Causes: | The paper entry sensor connector makes poor contact. Defective paper entry sensor. The optical path of the paper entry sensor is blocked by foreign matter. Defective finisher main PWB. |
| Remedy: | The paper entry sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective paper entry sensor. Replace the paper entry sensor and check for correct operation. The optical path of the paper entry sensor is blocked by foreign matter. Remove the foreign matter. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8460 |
| Description: | EEPROM problem (optional document finisher) Reading from or writing to EEPROM cannot be performed. |
| Causes: | Defective EEPROM or finisher main PWB. |
| Remedy: | Replace the finisher main PWB and check for correct operation. |
| Error code: | C8500 |
| Description: | Main program error (Mail Box) / Mail Box communication error Object: 4000-sheet finisher + Mail box |
| Causes: | The main program of the mail box is faulty when turning the power on. The communication error appears 10 times continuously after finishing the mail box firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the MB firmware and the DF firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB main PWB - DF main PWB 4 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8510 |
| Description: | MB conveying motor error 1 Object: 4000-sheet finisher + Mail box |
| Causes: | The MB home position sensor does not turn on after passing 5s during the initial operation. |
| Remedy: | 1 Checking the MB conveying roller The MB conveying roller is not assembled properly. If the MB conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB conveying motor - MB main PWB • MB home position sensor - MB main PWBPWB Wiring diagram 3 Replacing the MB conveying motor The MB conveying motor is faulty. Execute U240 [Mail Box] > [Conv]. If the MB conveying motor does not properly operate, replace it. 4 Checking the MB home position sensor The MB home position sensor is not properly attached or faulty. Reattach the MB home position sensor and execute U241 [Mail Box] > [Motor HP]. If the sensor does not properly operate, replace it. Executing U241 5 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. |
| Error code: | C8800 |
| Description: | Main program error (DF) / Engine - DF communication error Object: 4000-sheet finisher |
| Causes: | The main program is faulty when turning on the power. The Engine -DF communication error is detected 10 times continuously. |
| Remedy: | 1 Resetting the main power The program does not start up properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the DP firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • DF main PWB - Engine PWB Wiring diagram 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C8900 |
| Description: | DF backup error Object: 4000-sheet finisher (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • DF main PWB - Engine PWB Wiring diagram 2 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8910 |
| Description: | Backup memory data problem (optional of 3000-sheet document finisher) Read and write data does not match 3 times in succession. |
| Causes: | Poor contact in the connector terminals Defective punch PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the punch PWB and the connector YC4 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective punch PWB. Replace the punch PWB and check for correct operation. |
| Error code: | C8920 |
| Description: | Mailbox backup problem (optional mailbox of 3000-sheet document finisher) Read and write data does not match. |
| Causes: | Poor contact in the connector terminals. Defective mailbox main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the mailbox main PWB and the connector YC7 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective mailbox main PWB. Replace the mailbox main PWB and check for correct operation. |
| Error code: | C8930 |
| Description: | BF unit backup error Object: 4000-sheet finisher + Folding unit (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 2 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C9000 |
| Description: | Main program error (DP) / Document Processor communication error |
| Causes: | The document processor cannot be communicated. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware and the DP firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DP main PWB - Engine PWB Wiring diagram 3 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. Detaching and reattaching the DP main PWB 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C9040 |
| Description: | DP lift motor ascend error |
| Causes: | The DF lift upper limit sensor does not detect ON when passing 1500 pulses 5 times or more while the DP lift motor drives to ascend. |
| Remedy: | 1 Checking the DP original feed lift plate The DP original feed lift plate is not properly attached. If the DP original feed lift plate does not move up and down manually, repair the part that restricts the operation. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DP lift motor - DP main PWB • DP lift upper limit sensor - DP main PWB Wiring diagram 3 Replacing the DP lift motor The DP lift motor is faulty. Execute U243 [Lift Motor]. If the DP lift motor does not properly operate, replace the motor. 4 Checking the DP lift upper limit sensor The DP lift upper limit sensor is not properly attached or faulty. Reattach the DP lift upper limit sensor and execute U244 [Lift U-Limit]. If the sensor does not properly operate, replace it. Executing U244 5 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. |
| Error code: | C9050 |
| Description: | DP lift motor descend error |
| Causes: | The DF lift lower limit sensor does not detect ON when passing 1500 pulses while the DP lift motor drives to descend. (3 times of retries) |
| Remedy: | 1 Checking the DP original feed lift plate The DP original feed lift plate is not properly attached. If the DP original feed lift plate does not move up and down manually, repair the part that restricts the operation. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DP lift motor - DP main PWB • DP lift lower limit sensor - DP main PWB Wiring diagram 3 Replacing the DP lift motor The DP lift motor is faulty. Execute U243 [Lift Motor]. If the DP lift motor does not properly operate, replace the motor. 4 Checking the DP lift lower limit sensor The DP lift lower limit sensor is not properly attached or faulty. Reattach the DP lift lower limit sensor and execute U244 [Lift L-Limit]. If the sensor does not properly operate, replace it. Executing U244 5 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. |
| Error code: | C9060 |
| Description: | DP EEPROM error |
| Causes: | Read data and write data to the EEPROM do not match 3 times continuously. |
| Remedy: | 1 Checking the EEPROM The EEPROM is not properly installed. Reattach the EEPROM on the DP main PWB. 2 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. Detaching and reattaching the DP main PWB 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the DP main PWB and execute U411. |
| Error code: | C9070 |
| Description: | DP - SHD communication error |
| Causes: | The communication error between the DP main PWB and the DPSHD PWB was detected during communication. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DPSHD PWB - DP main PWB Wiring diagram 2 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. 3 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. |
| Error code: | C9080 |
| Description: | LED failure detection (For the internal count) |
| Causes: | After 4 blocks of the LED lamps of the DPCIS are lit when turning the power on, the acquired peak value of some blocks is at the reference value or less. (The light level detected by the CIS is not enough.) |
| Remedy: | 1 Checking the LED lamp The LED lamp of the DPCIS does not light. 0 Executing U203 2 Checking the DPSHD PWB The DPSHD PWB is not properly connected. Reconnect the DPSHD PWB to the DPCIS. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DPSHD PWB - DP main PWB Wiring diagram 4 Executing U411 DP scanning is not properly adjusted. Execute U411 [DP FD (ChartB) ] and [DP FD (ChartA)]. Executing U411 5 Replacing the DPCIS The DPCIS is faulty. Replace the DPCIS, and then execute U091 and U411. Detaching and reattaching the DPCIS 6 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F030 |
| Description: | Main PWB system error |
| Causes: | Defective main PWB. |
| Remedy: | Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F041 |
| Description: | Over than available setting number tray detection error |
| Causes: | Over than available setting number tray is installed. |
| Remedy: | Remove the available setting number tray. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F060 |
| Description: | Engine RAM error |
| Causes: | Defective engine PWB. |
| Remedy: | Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | F070 |
| Description: | Communication error between System-CPU and Engine-CPU |
| Causes: | Switching regulator • Replace the fuse (F210). • Replace the switching regulator. LGC board SYS board If the problem is not corrected with the replacement of the LGC board, reinstall the removed LGC board and replace the SYS board. IMG board If the problem is still not corrected with the replacement of the SYS board, reinstall the removed SYS board and replace the IMG board. |
| Remedy: | (1) Check if the connector CN104 on the SYS board and CN130, CN131, CN134 on the SYSIF board is disconnected. (2) Check if the connector CN10 on the SLG board is disconnected. (3) Check if the harness connecting the SYSIF board and SLG board is disconnected or open circuited. (4) Check if the harness connecting the SYSIF board and LGC board is disconnected or open circuited. (5) Check if the connection of the SYS board (CN104) and SYSIF board (CN130) is open circuited. (6) If the SYS board has been replaced, check if the jumper pin setting on the SYS board is correct. (The jumper pin should be inserted between pin 2 and 3 of CN103 and CN115.) (7) Check the version of the system ROM on the SYS board. (8) Check the version of the engine ROM version on the LGC board. (9) Check the version of the scanner ROM version on the SLG board. (10) Replace the SYS board. (11) Replace the SLG board. (12) Replace the LGC board. (13) Replace the SYSIF board. |
| Error code: | F080 |
| Description: | Flash ROM error (during download) |
| Causes: | Defective flash ROM. |
| Remedy: | Defective flash ROM. Replace the engine PWB and check for correct operation. |
| Error code: | F090 |
| Description: | SRAM abnormality on SYS board |
| Causes: | SRAM (SYS board) |
| Remedy: | (1) Turn the power OFF and start up the Setting Mode (08). (2) When “SRAM ERROR DOES IT INITIALIZE” is displayed on the LCD, check the destination and then press the [START] button. If the destination is not correct, key in the correct one and then press the [START] button. (3) After the confirmation message is displayed on the LCD, press the [INTERRUPT] button (to initialize the SRAM). (4) Perform the panel calibration (08-692). (5) Perform the initialization at the software version upgrade (08-947). (6) Enter the serial number (08-995). Be sure that the serial number is the same as that on the identification label attached on the rear cover of the equipment. Note: The MAC address of the equipment is generated based on this serial number. Entering the incorrect serial number may result in an inability to access the network due to an invalid MAC address. (7) Initialize the NIC information (08-693). (8) Turn the power OFF and then start up with the Adjustment mode (05). (9) Turn the power OFF and then back ON. If the error is not recovered, replace the SRAM on the SYS board. |
| Error code: | F14F |
| Description: | Power source PWB secondary side error |
| Causes: | Defective power source PWB. |
| Remedy: | Defective power source PWB. Replace the power source PWB and check for correct operation. |
