Kyocera TASKalfa 3011i
Рейтинг
Актуальный
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
100000
Скорость печати
A4
30
Цветность печати
черно-белая
Общие характеристики |
|
|---|---|
Цветность печати |
|
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Копир |
|
Факс |
|
Сканер |
|
Тип устройства |
МФУ |
Печать фотографий |
|
Телефон |
|
Макс. формат |
A3 |
Число страниц в месяц |
100 000 |
Область применения |
большой офис |
Размещение |
напольный |
Принтер |
|
Макс, ширина отпечатка |
297 |
Двусторонняя печать |
|
Прямая печать |
|
Печать без полей |
|
Пигментные чернила |
|
Время разогрева |
18 |
Макс, длина отпечатка |
420 |
Макс, разрешение для ч/б печати |
|
| По X | 600 |
| По Y | 600 |
Скорость ч/б печати |
|
| A4 | 30 |
Копир |
|
Шаг масштабирования |
0,01 |
Макс, количество копий за цикл |
999 |
Время выхода первой копии |
3,6 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По Y | 600 |
| По X | 600 |
Скорость ч/б копирования |
|
| A3 | 15 |
Сканер |
|
Стандарт TWAIN |
|
Отправка изображения по e-mail |
|
Слайд-адаптер |
|
Оттенки серого |
256 |
Тип сканера |
планшетный |
Макс. формат оригинала |
A3 |
Макс, размер сканирования |
|
| По X | 297 |
| По Y | 420 |
Разрешение сканера |
|
| По Х | 600 |
Расходные материалы |
|
Количество картриджей |
1 |
Ресурс фотобарабана |
300 000 |
Ресурс девелопера |
300 000 |
Ресурс ч/б картриджа/тонера |
20 000 |
Печать на: |
|
| Этикетках |
|
| Матовой бумаге |
|
| Пленках |
|
| Конвертах |
|
| Карточках |
|
| Глянцевой бумаге |
|
| Фотобумаге |
|
| Рулоне |
|
| CD/DVD |
|
Плотность бумаги |
|
| Максимальная | 256 |
| Минимальная | 45 |
Факс |
|
Макс, скорость передачи данных |
33,6 Кбит/с |
Телефон |
|
Caller ID |
|
АОН |
|
Стандарт DECT |
|
Спикерфон |
|
Автоответчик |
|
Беспроводная трубка |
|
Проводная трубка |
|
Шрифты и языки управления |
|
Языки управления |
|
| PCL 5c |
|
| PCL 6 |
|
|
|
|
| PostScript |
|
| PostScript 3 |
|
| PostScript 2 |
|
Количество установленных шрифтов |
|
| PostScript | 136 |
| PCL | 93 |
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Стандартная | 1 100 |
| Максимальная | 4 100 |
Вывод бумаги |
|
| Максимальный | 3 200 |
| Стандартный | 250 |
Финишер |
|
Брошюровщик |
|
Степлер |
|
Сортер |
|
Интерфейсы |
|
Количество слотов расширения |
2 |
Количество свободных слотов расширения |
2 |
Версия USB |
2,0 |
Ethernet (RJ-45) |
|
USB |
|
Устройство для чтения карт памяти |
|
Веб-интерфейс |
|
Bluetooth |
|
AirPrint |
|
Инфракрасный порт |
|
RS-232 |
|
FireWire (IEEE 1394) |
|
Wi-Fi |
|
LPT |
|
Поддержка карт памяти |
|
| Secure Digital |
|
Память/Процессор |
|
Частота процессора |
1 000 |
Объем памяти |
2 048 |
Дополнительная информация |
|
Экран |
|
Диагональ дисплея |
9 |
Работа от аккумулятора |
|
Поддержка ОС |
|
| Windows |
|
| Linux |
|
| Mac OS |
|
Потребляемая мощность |
|
| При работе | 620 |
| В режиме ожидания | 120 |
Уровень шума |
|
| В режиме ожидания | 25,5 |
| При работе | 46,5 |
Габариты |
|
Ширина |
594 |
Глубина |
696 |
Высота |
680 |
Вес |
58 |
Модули
Scanner Section 1
FRAMES 1
Paper Feed Section 1
COVERS and LABELS
Paper Feed Section 4
FRAMES 2
COOLING SECTION
CASSETTE ASSEMBLY
Inner Section
Frames 3
Covers 2
DUPLEX
FRAME L
Frames 4
Electrical Components 1
Image Formation Section
PAPER FEED SECTION 2
Fuser Section
PAPER CASSETTE
Covers 1
Electrical Components 3
Paper Conveying Section 3
DRIVE SECTION 2
ADF 1
Developer Section
Frames 5
Laser Scanner Section
ELECTRICAL COMPONENTS 2
Paper Conveying Section 4
Exit Section
PAPER FEED
Drive Section 1
Paper Conveying Section 2
SCANNER SECTION 2
Paper Conveying Section 1
Operation Section
Paper Feed Section 3
Детали PAPER CASSETTE
| Деталь: | SENSOR OPT |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | SWITCH RELEASE |
| Парткод: | 302NL17020 |
| Деталь: | MOUNT CONNECTOR |
| Парткод: | 302RH17010 |
| Деталь: | GUIDE FFC |
| Парткод: | 302RH17020 |
| Деталь: | WIRE FFC CCD |
| Парткод: | 302RH46210 |
| Деталь: | FILM FFC CCD |
| Парткод: | 302RH17030 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBFZZ65C001H01 |
| Деталь: | PARTS ISU ASSY H SP |
| Парткод: | 302ND93110 |
| Деталь: | COVER LENS |
| Парткод: | 302MV17030 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+010H01 |
| Деталь: | PARTS MOUNT LED ASSY SP |
| Парткод: | 302L793100 |
| Деталь: | WIRE FFC LED |
| Парткод: | 302RH46250 |
| Деталь: | GUIDE FFC LED C |
| Парткод: | 302K317172 |
| Деталь: | SHEET FFC LED |
| Парткод: | 302RH17110 |
| Деталь: | MOTOR REVERSE |
| Парткод: | 302HN44100 |
| Деталь: | PARTS GEAR Z18-Z63R SP |
| Парткод: | 302K394370 |
| Деталь: | GEAR P54 |
| Парткод: | 302RH17060 |
| Деталь: | MOUNT DRIVE |
| Парткод: | 302NL17010 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 302NL17030 |
| Деталь: | PULLEY DRUM |
| Парткод: | 302RH17040 |
| Деталь: | SHAFT MOTOR DRIVE |
| Парткод: | 302RH17050 |
| Деталь: | WIRE SCANNER BLACK |
| Парткод: | 302K317140 |
| Деталь: | WIRE SCANNER GRAY |
| Парткод: | 302K317150 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | MOUNT DP |
| Парткод: | 302NL17050 |
| Деталь: | PIN FUSER COVER |
| Парткод: | 2FB20860 |
| Деталь: | CUSHION ISU |
| Парткод: | 302K317180 |
| Деталь: | PARTS CONTACT-GLASS ASSY(C) SP |
| Парткод: | 302RH94160 |
| Деталь: | PARTS CONTACT-GLASS ASSY(I) SP |
| Парткод: | 302RH94150 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 302ND94800 |
| Деталь: | PLATE SIZE DETECTION |
| Парткод: | 302K309410 |
| Деталь: | SENSOR OPT |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000001+H01 |
| Деталь: | HOLDER CASSETTE HOOK |
| Парткод: | 302NL09021 |
| Деталь: | LEVER CASSETTE HOOK |
| Парткод: | 302K909640 |
| Деталь: | PULLEY EJECT |
| Парткод: | 303LW24060 |
| Деталь: | SHAFT HOOK FULCRUM |
| Парткод: | 303NF02280 |
| Деталь: | SHAFT HOOK PULLEY |
| Парткод: | 302K909630 |
| Деталь: | SPRING CASSETTE HOOK |
| Парткод: | 302NL09060 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | LABEL HIGH TEMPERATURE CAUTION |
| Парткод: | 303RC34080 |
| Деталь: | HEATER DEHUMIDIFIER 100 |
| Парткод: | 302RH44030 |
| Деталь: | HEATER DEHUMIDIFIER 120 |
| Парткод: | 302RH44040 |
| Деталь: | HEATER DEHUMIDIFIER 240 |
| Парткод: | 302RH44050 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610014++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PIN FRONT HANDLE |
| Парткод: | 302MV02240 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610011++H01 |
| Деталь: | HANDLE |
| Парткод: | 302JF02160 |
| Деталь: | SEAL HANDLE |
| Парткод: | 302FZ03110 |
| Деталь: | CAP HANDLE |
| Парткод: | 302FZ02580 |
| Деталь: | MOUNT DECK PI |
| Парткод: | 302K302841 |
| Деталь: | GUIDE WIRE MAIN SW |
| Парткод: | 302RH39110 |
| Деталь: | CAP DECK PIN |
| Парткод: | 302K302920 |
| Деталь: | MOUNT DECK DRAWER |
| Парткод: | 302K302911 |
| Деталь: | WIRE PF DRAWER 200 |
| Парткод: | 302K346660 |
| Деталь: | WIRE PF DRAWER |
| Парткод: | 302K346470 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | WIRE CASSETTE HEATER JOINT |
| Парткод: | 302NL46280 |
| Деталь: | SHAFT HANDLE |
| Парткод: | 302MV02220 |
| Деталь: | MOUNT REAR HANDLE |
| Парткод: | 302MV02232 |
| Деталь: | STOPPER 4 |
| Парткод: | 302FZ25740 |
| Деталь: | SPONGE LOWER RIGHT SP |
| Парткод: | 302LF33B10 |
| Деталь: | STAY SHIELD POWER |
| Парткод: | 302K002751 |
| Деталь: | PULLEY PICKUP ASSY |
| Парткод: | 302HN06080 |
| Цена: | 480 ₽ |
| Деталь: | PULLEY FEED ASSY |
| Парткод: | 302F906230 |
| Цена: | 750 ₽ |
| Деталь: | RETARD ROLLER ASSY |
| Парткод: | 302F909171 |
| Цена: | 900 ₽ |
| Деталь: | PARTS PRIMARY FEED ASSY SP |
| Парткод: | 302MV94061 |
| Деталь: | Крышка планшетного сканера |
| Парткод: | 1202H70UN0 |
| Цена: | 4 200 ₽ |
| Деталь: | COVER SW FEED |
| Парткод: | 302MV07080 |
| Деталь: | GUIDE COVER INNER |
| Парткод: | 302MV07051 |
| Деталь: | COVER RIGHT LOW |
| Парткод: | 302RH04400 |
| Деталь: | HOLDER SPRING |
| Парткод: | 302MV07070 |
| Деталь: | Cover Handle |
| Парткод: | 302NL06060 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SPRING FEED LOW |
| Парткод: | 303NN24180 |
| Деталь: | SHAFT FEED B |
| Парткод: | 302BG06152 |
| Деталь: | PULLEY 15 DUPLEX |
| Парткод: | 3HY07120 |
| Деталь: | SPRING LID |
| Парткод: | 302FZ20021 |
| Деталь: | HOOK FEED LOW |
| Парткод: | 302K906670 |
| Деталь: | SHAFT FEED LOW HOOK |
| Парткод: | 302NL06070 |
| Деталь: | HANDLE FEED LOW |
| Парткод: | 303PC06060 |
| Деталь: | HOLDER HOOK F |
| Парткод: | 302NL06040 |
| Деталь: | HOLDER HOOK R |
| Парткод: | 302NL06050 |
| Деталь: | BAND B |
| Парткод: | 2BG06480 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000001+H01 |
| Деталь: | SENSOR OPT |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | SPRING EARTH SW |
| Парткод: | 303NN24250 |
| Деталь: | WIRE RIGHT COVER SW |
| Парткод: | 302MV46520 |
| Деталь: | PARTS COVER RIGHT LOW ASSY SP |
| Парткод: | 302RH94170 |
| Деталь: | BASE TERMINAL |
| Парткод: | 302K339061 |
| Деталь: | TERMINAL DRUM A |
| Парткод: | 302K339070 |
| Деталь: | TERMINAL DLP A |
| Парткод: | 302K339080 |
| Деталь: | TERMINAL TRANSFER A |
| Парткод: | 302K339090 |
| Деталь: | TERMINAL SEPARATION A |
| Парткод: | 302K339100 |
| Деталь: | FRAME REAR UPPER |
| Парткод: | 302K302170 |
| Деталь: | LEVER RIGHT SW |
| Парткод: | 302K302A10 |
| Деталь: | PIN FRONT CASSETTE RAIL |
| Парткод: | 302GR02240 |
| Деталь: | PIN CASSETTE RAIL |
| Парткод: | 2FB06710 |
| Деталь: | PULLEY CASSETTE RAIL |
| Парткод: | 302NL09030 |
| Деталь: | RAIL CASSETTE LEFT |
| Парткод: | 302NL02091 |
| Деталь: | RAIL CASSETTE RIGHT |
| Парткод: | 302NL02211 |
| Деталь: | PAD RAIL |
| Парткод: | 303MH06010 |
| Деталь: | SPRING LEVER LIFT CASSETTE |
| Парткод: | 302MV02310 |
| Деталь: | LEVER LIFT CASSETTE |
| Парткод: | 302K302760 |
| Деталь: | RAIL FEED |
| Парткод: | 303NN02370 |
| Деталь: | GUIDE DRUM COVER |
| Парткод: | 302K302640 |
| Деталь: | RAIL DRUM |
| Парткод: | 302K302121 |
| Деталь: | RAIL HOLDER FRONT |
| Парткод: | 302K302690 |
| Деталь: | RAIL HOLDER REAR |
| Парткод: | 302K302700 |
| Деталь: | STOPPER CONTAINER |
| Парткод: | 302K302960 |
| Деталь: | BASE LSU |
| Парткод: | 302RH02030 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | WIRE LIMIT SENSOR |
| Парткод: | 302NL46370 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | HOLDER SENSOR |
| Парткод: | 302NL06010 |
| Деталь: | GUIDE PRIMARY FEED |
| Парткод: | 303NN02450 |
| Деталь: | STAY UPPER FEED |
| Парткод: | 303NN02143 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302K302811 |
| Деталь: | STAY FRONT FRAME |
| Парткод: | 302MV02041 |
| Деталь: | WIRE MAIN SWITCH |
| Парткод: | 302RH46170 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | WIRE FUSER HEATER |
| Парткод: | 302RH46100 |
| Деталь: | GUIDE FUSER |
| Парткод: | 302NL02071 |
| Деталь: | MOUNT FUSER FRONT |
| Парткод: | 302K325340 |
| Деталь: | ADJUSTER FUSER |
| Парткод: | 302K325350 |
| Деталь: | FRAME FRONT UPPER |
| Парткод: | 302K302161 |
| Деталь: | JOINT FUSER |
| Парткод: | 302NL02100 |
| Деталь: | SW. SEESAW |
| Парткод: | 7SC020403+++H01 |
| Деталь: | PULLEY CASSETTE RAIL |
| Парткод: | 302NL09130 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | WIRE BRIDGE JOINT |
| Парткод: | 302RH46310 |
| Деталь: | BRACKET DRAWER |
| Парткод: | 302NL02080 |
| Деталь: | STAY REAR FRAME |
| Парткод: | 302NL02060 |
| Деталь: | FILM UPPER REAR DUCT |
| Парткод: | 302FB23340 |
| Деталь: | DUCT MAIN UPPER |
| Парткод: | 302K333010 |
| Деталь: | DUCT MAIN LOWER |
| Парткод: | 302K333020 |
| Деталь: | DUCT SEPARATION |
| Парткод: | 302K333030 |
| Деталь: | DUCT REAR UPPER |
| Парткод: | 302K333041 |
| Деталь: | DUCT REAR LOWER |
| Парткод: | 302K333051 |
| Деталь: | PARTS FAN MOTOR SP |
| Парткод: | 302NG94220 |
| Деталь: | SEAL MOTOR DC |
| Парткод: | 302LC31511 |
| Деталь: | DUCT BRACKET |
| Парткод: | 302RH33010 |
| Деталь: | PARTS PWB THERMISTOR ASSY SP |
| Парткод: | 302NP94120 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | ACCESS.BAND |
| Парткод: | 7YZM410004++H01 |
| Деталь: | Ролик подачи бумаги |
| Парткод: | 302N406030 |
| Цена: | 440 ₽ |
| Деталь: | Ролик отделения бумаги |
| Парткод: | 302N406040 |
| Цена: | 450 ₽ |
| Деталь: | Резина ролика отделения бумаги |
| Парткод: | CET4322PT |
| Цена: | 110 ₽ |
| Деталь: | Резина ролика захвата бумаги |
| Парткод: | CET7806BPT |
| Цена: | 110 ₽ |
| Деталь: | Резина ролика подачи бумаги |
| Парткод: | CET7829 |
| Цена: | 150 ₽ |
| Деталь: | COVER INNER FRONT |
| Парткод: | 302NL04240 |
| Деталь: | COVER HOLDER BOX |
| Парткод: | 302NL04260 |
| Деталь: | SPRING STOPPER CONTAINER |
| Парткод: | 302K304360 |
| Деталь: | STOPPER CONTAINER |
| Парткод: | 302K304280 |
| Деталь: | SPRING LEVER CONTAINER |
| Парткод: | 302K304300 |
| Деталь: | LABEL TONER CONTAINER PULL |
| Парткод: | 302K334170 |
| Деталь: | LEVER CONTAINER |
| Парткод: | 302K304270 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302H004660 |
| Деталь: | STRAP COVER FRONT L |
| Парткод: | 302K304320 |
| Деталь: | STRAP COVER FRONT R |
| Парткод: | 302K304230 |
| Деталь: | LABEL W1 |
| Парткод: | 302NL34110 |
| Деталь: | SPRING STOPPER DLP B |
| Парткод: | 302K302990 |
| Деталь: | LEVER HOOK REMOVEMENT |
| Парткод: | 302NL02320 |
| Деталь: | STOPPER REMOVEMENT DLP |
| Парткод: | 302K302361 |
| Деталь: | PLATE STOPPER REMOVEMENT |
| Парткод: | 302K302772 |
| Деталь: | LABEL PUSH STOPPER |
| Парткод: | 302NL34060 |
| Деталь: | LABEL ARROW STOPPER |
| Парткод: | 302NL34070 |
| Деталь: | LABEL BOTTLE WASTE |
| Парткод: | 302NL34100 |
| Деталь: | PARTS CLEANER REGIST ASSY SP |
| Парткод: | 302NL94040 |
| Деталь: | SHEET BASE MIDDLE |
| Парткод: | 302NL02340 |
| Деталь: | SPRING DLP PUSH |
| Парткод: | 302K302A60 |
| Деталь: | SLIDER REMOVEMENT DLP |
| Парткод: | 302NL02190 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | RAIL DLP |
| Парткод: | 302NL02120 |
| Деталь: | SEAL BLADE SIDE B |
| Парткод: | 302HG12440 |
| Деталь: | PULLEY CASSETTE |
| Парткод: | 302K309070 |
| Деталь: | PLATE DLP BIAS |
| Парткод: | 302K302580 |
| Деталь: | PARTS CONT SENSOR ASSY SP |
| Парткод: | 302KK94070 |
| Деталь: | WIRE CONTAINER RAIL |
| Парткод: | 302RH46060 |
| Деталь: | PARTS PWB RFID ASSY SP |
| Парткод: | 302K394070 |
| Деталь: | SHEET RAIL |
| Парткод: | 302NL02140 |
| Деталь: | WIRE CONTAINER SET |
| Парткод: | 302NL46080 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | PLATE CONTAINER SWITCH |
| Парткод: | 302K302A40 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000001+H01 |
| Деталь: | HOLDER SENSOR |
| Парткод: | 302NL02220 |
| Деталь: | SHAFT GEAR |
| Парткод: | 303NN31060 |
| Деталь: | PIN JOINT CONTAINER C |
| Парткод: | 302K302860 |
| Деталь: | BUSH MIXER /A-49 DLP A4 |
| Парткод: | 5MVM177XN007 |
| Деталь: | GEAR FEED DRIVE Z20L |
| Парткод: | 302K906240 |
| Деталь: | GEAR CONTAINER Z42R |
| Парткод: | 302NL02170 |
| Деталь: | GEAR Z22R 40R |
| Парткод: | 302NL02180 |
| Деталь: | GEAR Z23L |
| Парткод: | 302NL02230 |
| Деталь: | PIN JOINT CONTAINER B |
| Парткод: | 302K302850 |
| Деталь: | PARTS GEAR CONTAINER Z25L SP |
| Парткод: | 302K394270 |
| Деталь: | TORQUE LIMITER 4000 |
| Парткод: | 302MW31010 |
| Деталь: | PARTS GEAR CONTAINER Z35R SP |
| Парткод: | 302K394280 |
| Деталь: | GEAR Z35L |
| Парткод: | 302HN31200 |
| Деталь: | COVER RAIL DRIVE |
| Парткод: | 302NL02150 |
| Деталь: | JOINT CONTAINER PADDLE A |
| Парткод: | 302K302540 |
| Деталь: | SPRING JOINT PADDLE |
| Парткод: | 302K302780 |
| Деталь: | SPRING DLP GROUND |
| Парткод: | 302K302590 |
| Деталь: | MOUNT DLP PWB |
| Парткод: | 302RH02180 |
| Деталь: | PARTS PWB DEVE CONNECT ASSY SP |
| Парткод: | 302RH94210 |
| Деталь: | COVER RAIL DLP |
| Парткод: | 302NL02160 |
| Деталь: | MOUNT CONTAINER |
| Парткод: | 302K302191 |
| Деталь: | SHEET MOUNT CONTAINER |
| Парткод: | 302K302240 |
| Деталь: | WIRE REGIST |
| Парткод: | 302K346270 |
| Деталь: | SPRING DEV PUSH F |
| Парткод: | 2C902590 |
| Деталь: | BASE MIDDLE |
| Парткод: | 302NL02040 |
| Деталь: | HANDLE COVER LEFT |
| Парткод: | 302MV02160 |
| Деталь: | SPONGE DLP LEVER |
| Парткод: | 302K302A70 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302K302811 |
| Деталь: | COVER FRONT |
| Парткод: | 302RH04010 |
| Деталь: | EMBLEM KC 1SG 70 B |
| Парткод: | 302DY04010 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 302H004652 |
| Деталь: | PLATE MAGNET |
| Парткод: | 302NL04270 |
| Деталь: | SHEET COVER FRONT |
| Парткод: | 302NL34050 |
| Деталь: | COVER INNER BASE |
| Парткод: | 302K302260 |
| Деталь: | LABEL EMBLEM H |
| Парткод: | 302RH34010 |
| Деталь: | LABEL EMBLEM L |
| Парткод: | 302RG34010 |
| Деталь: | Направляющая подачи бумаги |
| Парткод: | 303N024021 |
| Деталь: | PANEL UNIT, MFC9840CDW |
| Парткод: | FK-7105 |
| Цена: | 24 500 ₽ |
| Деталь: | Прижимной вал |
| Парткод: | 302KK94290 |
| Цена: | 6 000 ₽ |
| Деталь: | COVER INNER FRONT SUB |
| Парткод: | 302K304350 |
| Деталь: | CAM REMOVEMENT DLP |
| Парткод: | 302K302330 |
| Деталь: | SHAFT REMOVEMENT DLP |
| Парткод: | 302K302320 |
| Деталь: | LEVER REMOVEMENT DLP |
| Парткод: | 302NL02310 |
| Деталь: | LABEL D |
| Парткод: | 302NL34080 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | MOUNT INTERLOCK SW |
| Парткод: | 302NL02201 |
| Деталь: | SPRING EARTH DRUM PWB |
| Парткод: | 302K302660 |
| Деталь: | PARTS PWB DRUM CONNECT ASSY SP |
| Парткод: | 302K394080 |
| Деталь: | MOUNT JUNCTION PWB |
| Парткод: | 302K302220 |
| Деталь: | COVER CONNECTOR |
| Парткод: | 302K302730 |
| Деталь: | SPRING EARTH CONNECTOR |
| Парткод: | 302K302740 |
| Деталь: | COVER EXIT TOP |
| Парткод: | 302NL04190 |
| Деталь: | PARTS HIGH VOLTAGE SP |
| Парткод: | 302NL94110 |
| Цена: | 4 800 ₽ |
| Деталь: | PARTS PWB ENGINE ASSY SP |
| Парткод: | 302RH94130 |
| Деталь: | WIRE ENGINE-LVU |
| Парткод: | 302RH46050 |
| Деталь: | WIRE FRONT SWITCH |
| Парткод: | 302RH46080 |
| Деталь: | WIRE PF JOINT |
| Парткод: | 302RH46090 |
| Деталь: | WIRE LSU JOINT |
| Парткод: | 302RH46330 |
| Деталь: | WIRE FUSER JAM SENS |
| Парткод: | 302K346030 |
| Деталь: | WIRE FFC HVU |
| Парткод: | 302NL46360 |
| Деталь: | WIRE FFC MAIN-ENGINE |
| Парткод: | 302RH46160 |
| Деталь: | WIRE FFC MAIN-ENGINE 2 |
| Парткод: | 302RH46470 |
| Деталь: | WIRE CASSETTE SWITCH |
| Парткод: | 302RH46030 |
| Деталь: | WIRE CONVEYING JOINT |
| Парткод: | 302NL46020 |
| Деталь: | WIRE EJECT FAN |
| Парткод: | 302RH46200 |
| Деталь: | WIRE COIN VENDER |
| Парткод: | 302RH46220 |
| Деталь: | WIRE POLYGON MOTOR JOINT |
| Парткод: | 302RH46120 |
| Деталь: | GUIDE WIRE REAR A |
| Парткод: | 302RH39070 |
| Деталь: | GUIDE WIRE REAR B |
| Парткод: | 302RH39080 |
| Деталь: | GUIDE WIRE REAR C |
| Парткод: | 302RH39090 |
| Деталь: | GUIDE WIRE ISU |
| Парткод: | 302RH39100 |
| Деталь: | PARTS IC EEPROM SP |
| Парткод: | 302LF94510 |
| Деталь: | MC-7105 |
| Парткод: | 302NL93080 |
| Деталь: | WT-475 |
| Парткод: | 302K393130 |
| Деталь: | DK-7105 |
| Парткод: | 302NL93020 |
| Деталь: | GUIDE FEED OUTER |
| Парткод: | 302NL06020 |
| Деталь: | PARTS ROLLER FEED UPPER SP |
| Парткод: | 302MV94310 |
| Деталь: | BUSH DU |
| Парткод: | 302K329270 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | PULLEY 26-6 DUPLEX |
| Парткод: | 303MR29040 |
| Деталь: | PULLEY PA |
| Парткод: | 302HN24400 |
| Деталь: | ACTUATOR DECK FEED |
| Парткод: | 302K302831 |
| Деталь: | SPRING EARTH FEED |
| Парткод: | 302MV07121 |
| Деталь: | GUIDE FEED LOW |
| Парткод: | 302MV07020 |
| Деталь: | PARTS ROLLER FEED LOWER SP |
| Парткод: | 302MV94320 |
| Деталь: | JOINT PULLEY 26-6 |
| Парткод: | 303NN24110 |
| Деталь: | ACTUATOR REGIST |
| Парткод: | 302K306140 |
| Деталь: | SPRING ACTUATOR REGIST |
| Парткод: | 302K306150 |
| Деталь: | GUIDE FEED |
| Парткод: | 302MV07030 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PARTS ROLLER REGIST LEFT SP |
| Парткод: | 302K394230 |
| Деталь: | BUSH 8 |
| Парткод: | 302H024830 |
| Деталь: | BUSH 8 EW |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | PARTS GEAR REGIST Z28L-Z18L SP |
| Парткод: | 302K394310 |
| Деталь: | SHEET REGIST LEFT |
| Парткод: | 302K306160 |
| Деталь: | VARISTOR TC |
| Парткод: | 302K345120 |
| Деталь: | SPRING EARTH REGIST B |
| Парткод: | 302K324350 |
| Деталь: | RAIL LINK ARM F |
| Парткод: | 302K302710 |
| Деталь: | SPRING EARTH REGIST A |
| Парткод: | 302K324310 |
| Деталь: | SPRING EARTH REGIST D |
| Парткод: | 302K324410 |
| Деталь: | SPRING EARTH REGIST C |
| Парткод: | 302K324380 |
| Деталь: | SHEET FEED OUT A |
| Парткод: | 302NL06080 |
| Деталь: | BELT FEED |
| Парткод: | 302MV07110 |
| Деталь: | SHEET DRUM COVER |
| Парткод: | 302K302630 |
| Деталь: | HOLDER DRUM COVER RIGHT |
| Парткод: | 302K302610 |
| Деталь: | HOLDER DRUM COVER LEFT |
| Парткод: | 302K302620 |
| Деталь: | ARM DRUM COVER FRONT |
| Парткод: | 302K302670 |
| Деталь: | ARM DRUM COVER REAR |
| Парткод: | 302K302680 |
| Деталь: | GUIDE TRANS LEFT |
| Парткод: | 302K324160 |
| Деталь: | STOPPER DRUM |
| Парткод: | 302K312080 |
| Деталь: | RAIL LINK ARM R |
| Парткод: | 302K302720 |
| Деталь: | PARTS FEED UNIT ASSY SP |
| Парткод: | 302K394540 |
| Деталь: | FK-7105 |
| Парткод: | 302NL93071 |
| Деталь: | FK-7107 |
| Парткод: | 302NL93061 |
| Деталь: | FK-7106 |
| Парткод: | 302NL93051 |
| Деталь: | PLATE NUMBER |
| Парткод: | 2BL04310 |
| Деталь: | PLATE NUMBER 2 |
| Парткод: | 2BL04370 |
| Деталь: | SHEET CASSETTE C |
| Парткод: | 302MV34300 |
| Деталь: | SHEET CASSETTE I |
| Парткод: | 302MV34430 |
| Деталь: | LABEL OPERATION L |
| Парткод: | 302MV34330 |
| Деталь: | EMBLEM CASSETTE |
| Парткод: | 302NL09070 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302RH04410 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 302NL09080 |
| Деталь: | CASSETTE |
| Парткод: | 302NL09010 |
| Деталь: | LABEL OPERATION S |
| Парткод: | 302MV34340 |
| Деталь: | LABEL CASSETTE SIZE A |
| Парткод: | 302MV34310 |
| Деталь: | LABEL CASSETTE SIZE B |
| Парткод: | 302MV34360 |
| Деталь: | LABEL OPERATION CURSOR |
| Парткод: | 302MV34320 |
| Деталь: | PLATE SIDE SWITCH |
| Парткод: | 302MV09050 |
| Деталь: | SPRING SIDE SWITCH |
| Парткод: | 302K309220 |
| Деталь: | ARM SIZE DETECTION |
| Парткод: | 302MV09040 |
| Деталь: | CURSOR END |
| Парткод: | 302K309270 |
| Цена: | 120 ₽ |
| Деталь: | SPRING CURSOR R |
| Парткод: | 2C907360 |
| Деталь: | SLIDER CURSOR END |
| Парткод: | 302K309141 |
| Деталь: | SPRING SIZE SET |
| Парткод: | 302K309360 |
| Деталь: | STOPPER SIZE SET |
| Парткод: | 302K309350 |
| Деталь: | CURSOR CASSETTE REAR |
| Парткод: | 302MV09080 |
| Деталь: | LEVER CURSOR SET |
| Парткод: | 302K309190 |
| Деталь: | SPRING CURSOR SET |
| Парткод: | 302K309370 |
| Деталь: | LABEL PAPER LIMIT |
| Парткод: | 302RH34070 |
| Деталь: | CURSOR CASSETTE FRONT |
| Парткод: | 302MV09090 |
| Деталь: | LEVER RELEASE CURSOR F |
| Парткод: | 302K309200 |
| Деталь: | SPRING RELEASE CURSOR F |
| Парткод: | 302K309210 |
| Деталь: | SPRING SIZE SET F |
| Парткод: | 302K309380 |
| Деталь: | SIZE FIX |
| Парткод: | 302HN09240 |
| Деталь: | PARTS GEAR Z18 SP |
| Парткод: | 302K394380 |
| Деталь: | SHAFT DRIVE LIFT |
| Парткод: | 302K309180 |
| Деталь: | PLATE LIFT BASE CASSETTE |
| Парткод: | 302K309171 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | SPRING CASSETTE LIFT EARTH |
| Парткод: | 302K309300 |
| Деталь: | BASE CASSETTE |
| Парткод: | 302MV09021 |
| Деталь: | PAD CASSETTE |
| Парткод: | 2C907140 |
| Деталь: | LABEL PAPER SET |
| Парткод: | 302MV34350 |
| Деталь: | LIFT BASE CASSETTE SUB |
| Парткод: | 302K309150 |
| Деталь: | SPRING LEVER LIFT CASSETTE SUB |
| Парткод: | 302K309160 |
| Деталь: | PLATE CASSETTE LEFT |
| Парткод: | 302NL09091 |
| Деталь: | PLATE CASSETTE RIGHT |
| Парткод: | 302NL09101 |
| Деталь: | PULLEY MPT BYPASS |
| Парткод: | 302FZ07020 |
| Деталь: | PULLEY, CASSETTE RAIL |
| Парткод: | 302FG07020 |
| Деталь: | CT-7105 |
| Парткод: | 302RH93010 |
| Деталь: | COVER INNER FRONT LOWER |
| Парткод: | 302MV04230 |
| Деталь: | STOPPER PAPER B |
| Парткод: | 302K304370 |
| Деталь: | COVER EXIT REAR |
| Парткод: | 302RH04380 |
| Деталь: | COVER TRAY |
| Парткод: | 302RH04360 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302H004560 |
| Деталь: | COVER TRAY LEFT |
| Парткод: | 302NL04180 |
| Деталь: | Cover Right Rear |
| Парткод: | 302RH04390 |
| Деталь: | LID COVER LEFT |
| Парткод: | 302FZ04240 |
| Деталь: | COVER MAIN SW |
| Парткод: | 302RH04290 |
| Деталь: | LABEL SW CAUTION |
| Парткод: | 302RH34020 |
| Деталь: | LABEL SW CAUTION JP |
| Парткод: | 302RH34030 |
| Деталь: | FOOT |
| Парткод: | 302MV02190 |
| Деталь: | COVER FRONT TOP |
| Парткод: | 302RH04020 |
| Деталь: | COVER LEFT LOW |
| Парткод: | 302RH04070 |
| Деталь: | COVER REAR TOP |
| Парткод: | 302RH04150 |
| Деталь: | COVER RIGHT TOP |
| Парткод: | 302RH04060 |
| Деталь: | COVER LEFT TOP |
| Парткод: | 302RH04080 |
| Деталь: | TRAY EJECT |
| Парткод: | 302K328300 |
| Деталь: | LID DF CONNECTOR |
| Парткод: | 302MN04100 |
| Деталь: | LID AK |
| Парткод: | 302NL04250 |
| Деталь: | COVER LEFT MIDDLE |
| Парткод: | 302RH04350 |
| Деталь: | COVER ISU FRONT |
| Парткод: | 302RH04090 |
| Деталь: | COVER FRONT MIDDLE |
| Парткод: | 302RH04340 |
| Деталь: | COVER KEYBOARD |
| Парткод: | 302RH04280 |
| Деталь: | MOUNT MAIN POWER |
| Парткод: | 302RH04320 |
| Деталь: | SPRING FUSER |
| Парткод: | 302F931270 |
| Деталь: | KEY MAIN POWER |
| Парткод: | 302RH04300 |
| Деталь: | HOLDER MAIN POWER |
| Парткод: | 302RH04310 |
| Деталь: | COVER REAR LOW |
| Парткод: | 302RH04140 |
| Деталь: | COVER FRONT RIGHT TOP |
| Парткод: | 302RH04250 |
| Деталь: | LID CARD-READER |
| Парткод: | 302RH04270 |
| Деталь: | SPONGE SHIELD A |
| Парткод: | 302RH04430 |
| Деталь: | SPONGE SHIELD B |
| Парткод: | 302RH04440 |
| Деталь: | SPONGE SHIELD C |
| Парткод: | 302RH04450 |
| Деталь: | PARTS PWB SWITCH ASSY SP |
| Парткод: | 302NG94300 |
| Деталь: | LABEL DEHUMIDIFIER SWITCH |
| Парткод: | 302RH34120 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | PARTS UNIT LOW VOLTAGE 100 SP |
| Парткод: | 302RH94220 |
| Деталь: | PARTS UNIT LOW VOLTAGE 200 SP |
| Парткод: | 302RH94230 |
| Деталь: | BOX POWER |
| Парткод: | 302RH39040 |
| Деталь: | BRACKET FAN POWER |
| Парткод: | 302RH39130 |
| Деталь: | PARTS,FAN COOLING CONVEYING SP |
| Парткод: | 302FZ94420 |
| Деталь: | LID POWER |
| Парткод: | 302RH39050 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | WIRE HEATER SWITCH JOINT |
| Парткод: | 302RH46420 |
| Деталь: | HOLDER TRANSFER |
| Парткод: | 302K324030 |
| Деталь: | HOLDER SEPARATION |
| Парткод: | 302K324100 |
| Деталь: | PLATE SEPARATION |
| Парткод: | 302K324150 |
| Деталь: | SPRING TRANSFER R |
| Парткод: | 302K324370 |
| Деталь: | BUSH TRANSFER ROLL R |
| Парткод: | 302K324430 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 302K324020 |
| Деталь: | BUSH TRANSFER ROLL F |
| Парткод: | 302K324240 |
| Деталь: | LABEL I |
| Парткод: | 302MV34180 |
| Деталь: | SPRING TRANSFER F |
| Парткод: | 302K324210 |
| Деталь: | COLLAR TRANS ROLLER |
| Парткод: | 302H722470 |
| Деталь: | GEAR TRANSFER Z18L |
| Парткод: | 302K324170 |
| Деталь: | LEVER TRANSFER |
| Парткод: | 302K324280 |
| Деталь: | SHEET TRANSFER RIGHT |
| Парткод: | 302K324520 |
| Деталь: | GUIDE TRANSFER RIGHT B |
| Парткод: | 302NL24110 |
| Деталь: | SPRING GUIDE TRANSFER |
| Парткод: | 302K324230 |
| Деталь: | HOOK TRANSFER R |
| Парткод: | 302K324260 |
| Деталь: | HOOK TRANSFER F |
| Парткод: | 302K324250 |
| Деталь: | LEVER HOOK R |
| Парткод: | 302MV24020 |
| Деталь: | LEVER HOOK F |
| Парткод: | 302MV24010 |
| Деталь: | TR-7105 |
| Парткод: | 302NL93090 |
| Деталь: | SPRING FEED |
| Парткод: | 302HN31410 |
| Деталь: | BUSH DRIVE |
| Парткод: | 302HN31590 |
| Деталь: | SPRING INPUT MPF |
| Парткод: | 302HN31650 |
| Цена: | 150 ₽ |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | 302HN31660 |
| Деталь: | SOLENOID MPF |
| Парткод: | 302HN44160 |
| Деталь: | PLATE DRIVE |
| Парткод: | 302K331030 |
| Деталь: | GEAR Z191R |
| Парткод: | 302K331040 |
| Деталь: | GEAR Z112R-Z37L |
| Парткод: | 302K331050 |
| Деталь: | GEAR Z38R |
| Парткод: | 302K331060 |
| Деталь: | GEAR Z29L INPUT DLP |
| Парткод: | 302K331070 |
| Деталь: | GEAR Z40R IDLE |
| Парткод: | 302K331081 |
| Деталь: | GEAR Z43L IDLE |
| Парткод: | 302K331090 |
| Деталь: | GEAR RATCHET Z28S |
| Парткод: | 302K331100 |
| Деталь: | GEAR INPUT FUSER Z30S |
| Парткод: | 302K331110 |
| Деталь: | GEAR Z101L-Z33L |
| Парткод: | 302K331120 |
| Деталь: | GEAR Z30R IDLE |
| Парткод: | 302K331140 |
| Деталь: | GEAR Z42R-Z36R |
| Парткод: | 302K331150 |
| Деталь: | GEAR Z48R-Z22S |
| Парткод: | 302K331160 |
| Деталь: | GEAR Z28S |
| Парткод: | 302K331170 |
| Деталь: | GEAR Z45S INPUT MPF A |
| Парткод: | 302K331180 |
| Деталь: | GEAR Z45S INPUT MPF B |
| Парткод: | 302K331190 |
| Деталь: | CAM MPF |
| Парткод: | 302K331200 |
| Деталь: | SPRING JOINT DLP |
| Парткод: | 302K331210 |
| Деталь: | SPRING RATCHET FUSER |
| Парткод: | 302K331220 |
| Деталь: | SHAFT CLUTCH FEED |
| Парткод: | 302K331240 |
| Деталь: | SPRING EARTH MOTOR |
| Парткод: | 302K331250 |
| Деталь: | PIN DRIVE A |
| Парткод: | 302K331260 |
| Деталь: | PARTS MOTOR-BL W30 SP |
| Парткод: | 302K394201 |
| Деталь: | SHAFT DU |
| Парткод: | 302NL31050 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CLUTCH 50 Z35R |
| Парткод: | 302KV44041 |
| Цена: | 900 ₽ |
| Деталь: | HOLDER FEED DRIVE A |
| Парткод: | 302NL31010 |
| Деталь: | HOLDER FEED DRIVE B |
| Парткод: | 302NL31020 |
| Деталь: | GEAR Z21L Z26R |
| Парткод: | 302NL31030 |
| Деталь: | PIN DRIVE |
| Парткод: | 302NL31040 |
| Деталь: | CONNECTOR 292254-2 |
| Парткод: | 7YCC02B1003+H01 |
| Деталь: | GEAR Z32L |
| Парткод: | 302KV31320 |
| Деталь: | BUSH DRIVE 8 |
| Парткод: | 302K331230 |
| Деталь: | WIRE DRIVE |
| Парткод: | 302RH46240 |
| Деталь: | DR-7105 |
| Парткод: | 302NL93010 |
| Деталь: | Ролик отделения бумаги в автоподатчике документов |
| Парткод: | 303LL07191 |
| Цена: | 5 500 ₽ |
| Деталь: | Ремень подачи бумаги в автоподатчике документов |
| Парткод: | 303LL07531 |
| Цена: | 1 900 ₽ |
| Деталь: | PARTS ROLLER REGISTRATION SP |
| Парткод: | 303M894110 |
| Деталь: | PARTS ROLLER CONVEYING A SP |
| Парткод: | 303M894120 |
| Деталь: | PARTS ROLLER CONVEYING B SP |
| Парткод: | 303M894130 |
| Деталь: | PARTS ROLLER EXIT SP |
| Парткод: | 303M894140 |
| Деталь: | Вал в узле автоматической подачи документов |
| Парткод: | 303M894150 |
| Деталь: | DV-7105 |
| Парткод: | 302NL93030 |
| Деталь: | MOUNT BOX |
| Парткод: | 302RH39060 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | MOUNT SCANNER RIGHT |
| Парткод: | 302MV02093 |
| Деталь: | PUSH SWITCH 03 SN /SW-192 N |
| Парткод: | 7SP03090001+H01 |
| Деталь: | MOUNT DF CONNECTOR |
| Парткод: | 302NL39080 |
| Деталь: | WIRE DF JOINT |
| Парткод: | 302RH46280 |
| Деталь: | MOUNT SCANNER FRONT |
| Парткод: | 302NL02242 |
| Деталь: | COVER EXIT FRONT TOP |
| Парткод: | 302MV04290 |
| Деталь: | PLATE EARTH ISU |
| Парткод: | 302K302A50 |
| Деталь: | WIRE HEATER SWITCH |
| Парткод: | 302NL46290 |
| Деталь: | MOUNT RIGHT INTERLOCK |
| Парткод: | 302K302940 |
| Деталь: | SW. MICRO |
| Парткод: | 7SM010205+++H01 |
| Деталь: | SPRING BYPASSFFED |
| Парткод: | 302H008140 |
| Деталь: | PIN FUSER COVER |
| Парткод: | 2FB20860 |
| Деталь: | WIRE RIGHT ILSW |
| Парткод: | 302RH46390 |
| Деталь: | WIRE INLET ASSY |
| Парткод: | 302RH46190 |
| Деталь: | SW.SEESAW |
| Парткод: | 7SC010105+++H01 |
| Деталь: | MOUNT INLET |
| Парткод: | 302RH39120 |
| Деталь: | LID VENDOR |
| Парткод: | 302FB26290 |
| Деталь: | MOUNT SCANNER ADJUST |
| Парткод: | 302K302210 |
| Деталь: | SPACER SCANNER ADJUST |
| Парткод: | 302K302200 |
| Деталь: | MOUNT OPTION |
| Парткод: | 302MV02132 |
| Деталь: | MOUNT OPTION |
| Парткод: | 302RH02090 |
| Деталь: | LID DEHUMIDIFIER SW |
| Парткод: | 302K302890 |
| Деталь: | LK-7106 |
| Парткод: | 302RH93030 |
| Деталь: | BOX CONTROLLER |
| Парткод: | 302RH39010 |
| Деталь: | PLATE CONTROLLER SUB |
| Парткод: | 302RH39030 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302RH94120 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302RH94250 |
| Деталь: | PARTS SSD SP |
| Парткод: | 302ND94670 |
| Деталь: | PARTS SSD SP |
| Парткод: | 302L794170 |
| Деталь: | PARTS STORAGE DEVICE SP |
| Парткод: | 302ND93180 |
| Деталь: | BRACKET HDD |
| Парткод: | 302RH39160 |
| Деталь: | PIN HDD |
| Парткод: | 302MV39341 |
| Деталь: | BUSHING FAN |
| Парткод: | 302JD19140 |
| Деталь: | PARTS WIFI UNIT SP |
| Парткод: | 303RR94010 |
| Деталь: | CONN.CORD ASSY FPC WIFI |
| Парткод: | 302ND46731 |
| Деталь: | RAIL KUIO |
| Парткод: | 302R439070 |
| Деталь: | PARTS PWB KUIO ASSY SP |
| Парткод: | 302K994270 |
| Деталь: | WIRE KUIO POWER |
| Парткод: | 302RH46410 |
| Деталь: | WIRE FFC KUIO |
| Парткод: | 302RH46320 |
| Деталь: | WIRE HDD POWER |
| Парткод: | 302RH46360 |
| Деталь: | WIRE HDD DATA 1 |
| Парткод: | 302N446130 |
| Деталь: | WIRE MAIN-LVU |
| Парткод: | 302RH46040 |
| Деталь: | LID CONTROLLER |
| Парткод: | 302RH39020 |
| Деталь: | PLATE OPTION |
| Парткод: | 302RH39220 |
| Деталь: | LID SD-CARD |
| Парткод: | 302RH39180 |
| Деталь: | ACTUATOR SIZE DETECTION |
| Парткод: | 302K908211 |
| Деталь: | SPRING-TORSION SIZE DETECTION |
| Парткод: | 302K908220 |
| Деталь: | HOLDER SIZE DETECTION |
| Парткод: | 302K908580 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | WIRE MPF SIZE UNIT 2 |
| Парткод: | 302MV46510 |
| Деталь: | TABLE MPF B |
| Парткод: | 302MV08430 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | TABLE MPF A |
| Парткод: | 302MV08420 |
| Деталь: | TABLE MPF |
| Парткод: | 302MV08410 |
| Деталь: | CURSOR FRONT MPF |
| Парткод: | 302MV08441 |
| Деталь: | CURSOR REAR MPF |
| Парткод: | 302MV08451 |
| Деталь: | GEAR 18 BYPASS |
| Парткод: | 2C906080 |
| Деталь: | TERMINAL PAPER SIZE |
| Парткод: | 2C906090 |
| Деталь: | PARTS PWB MPF SIZE ASSY SP |
| Парткод: | 302C994030 |
| Деталь: | GUIDE FRONT MPF WIRE |
| Парткод: | 302MV08460 |
| Деталь: | ORIGINAL SIZE SWITCH |
| Парткод: | 76727010 |
| Деталь: | GUIDE REAR MPF WIRE |
| Парткод: | 302MV08470 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 302R408220 |
| Деталь: | SPRING MPF |
| Парткод: | 302MV08500 |
| Деталь: | COVER MPF |
| Парткод: | 302MV08400 |
| Деталь: | STRAP LINK MPF |
| Парткод: | 302R408230 |
| Деталь: | STOPPER STRAP |
| Парткод: | 302K308470 |
| Деталь: | LABEL BYPASS TABLE |
| Парткод: | 302MV34270 |
| Деталь: | SHEET MPF WIRE A |
| Парткод: | 302MV08520 |
| Деталь: | LABEL MPF CAUTION |
| Парткод: | 302NL34140 |
| Деталь: | PARTS MPF TABLE ASSY SP |
| Парткод: | 302NL94152 |
| Деталь: | CUSHION GUIDE CHANGE |
| Парткод: | 302NL28040 |
| Деталь: | CUSHION GUIDE CHANGE B |
| Парткод: | 302K328240 |
| Деталь: | WIRE EXIT ROLLER EARTH |
| Парткод: | 302K328210 |
| Деталь: | BASE CONVEYING EXIT |
| Парткод: | 302K328011 |
| Деталь: | PARTS GEAR Z22S EXIT SP |
| Парткод: | 302K394350 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | PARTS ROLLER EXIT SP |
| Парткод: | 302K394240 |
| Деталь: | SPRING EXIT EARTH |
| Парткод: | 302K328170 |
| Деталь: | ACTUATOR EXIT OVERFLOW |
| Парткод: | 302NL28060 |
| Деталь: | WIRE EJECT UNIT |
| Парткод: | 302K346020 |
| Деталь: | LID EXIT EMPTY SWITCH |
| Парткод: | 302K328181 |
| Деталь: | PARTS SWITCH EXIT PAPER EMPTY SP |
| Парткод: | 302K394180 |
| Деталь: | PLATE EXIT OVERFLOW |
| Парткод: | 302NL28050 |
| Деталь: | GUIDE EXIT MIDDLE |
| Парткод: | 302K328100 |
| Деталь: | GUIDE EXIT PUSH |
| Парткод: | 302K328090 |
| Деталь: | SPRING GUIDE EXIT PUSH |
| Парткод: | 302K328260 |
| Деталь: | STATIC-ELIMINATOR EXIT |
| Парткод: | 302K328250 |
| Деталь: | CUSHION GUIDE CHANGE A |
| Парткод: | 302K328220 |
| Деталь: | GUIDE CHANGE |
| Парткод: | 302K328050 |
| Деталь: | PARTS GEAR Z25S EXIT INPUT SP |
| Парткод: | 302K394360 |
| Деталь: | FRAME EXIT LOWER |
| Парткод: | 302K328030 |
| Деталь: | SPRING PULLEY |
| Парткод: | 302F928170 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | FRAME EXIT UPPER |
| Парткод: | 302K328020 |
| Деталь: | MOTOR REVERSE |
| Парткод: | 302HN44100 |
| Деталь: | PARTS GEAR Z74R-Z22S EXIT SP |
| Парткод: | 302K394340 |
| Деталь: | SHAFT GEAR BELT |
| Парткод: | 303MA16560 |
| Деталь: | SOLENOID ASSY |
| Парткод: | 302F944090 |
| Деталь: | SPRING SOLENOID |
| Парткод: | 302K328150 |
| Деталь: | ACTUATOR EXIT JS |
| Парткод: | 302NL28020 |
| Деталь: | PLATE EXIT MOTOR |
| Парткод: | 302K328111 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | SPRING EXIT FUSER SWITCH |
| Парткод: | 302K328270 |
| Деталь: | ARM ACTUATOR EXIT |
| Парткод: | 302K328160 |
| Деталь: | GUIDE EXIT OVERFLOW JS A |
| Парткод: | 302K328321 |
| Деталь: | GUIDE EXIT OVERFLOW JS INCH |
| Парткод: | 302NL28030 |
| Деталь: | GUIDE EXIT PUSH JS |
| Парткод: | 302K328290 |
| Деталь: | PULLEY FEED 6 |
| Парткод: | 302K328330 |
| Деталь: | GUIDE EXIT PUSH JS |
| Парткод: | 302NL28010 |
| Деталь: | SPRING EXIT PUSH |
| Парткод: | 302FZ28270 |
| Деталь: | PARTS EXIT UNIT SP |
| Парткод: | 302NL94050 |
| Деталь: | PARTS EXIT UNIT J SP |
| Парткод: | 302NL94060 |
| Деталь: | Узел переноса изображения |
| Парткод: | TR-7105 |
| Деталь: | PARTS MOTOR LIFT ASSY SP |
| Парткод: | 302K394190 |
| Цена: | 6 000 ₽ |
| Деталь: | PARTS MOTOR-BL W10 SP |
| Парткод: | 302LC94291 |
| Деталь: | PLATE MOTOR LOW |
| Парткод: | 302MV31030 |
| Деталь: | HOLDER DRIVE LOW A |
| Парткод: | 302MV31010 |
| Деталь: | SPRING EARTH FEED LOW |
| Парткод: | 302MV31040 |
| Деталь: | BUSH DRIVE |
| Парткод: | 302HN31590 |
| Деталь: | CLUTCH 50 Z35R |
| Парткод: | 302KV44041 |
| Цена: | 900 ₽ |
| Деталь: | SHAFT CLUTCH FEED |
| Парткод: | 302K331240 |
| Деталь: | SHAFT GEAR |
| Парткод: | 303NN31060 |
| Деталь: | GEAR Z27L IDLE |
| Парткод: | 303NN31050 |
| Деталь: | GEAR Z40R IDLE |
| Парткод: | 302K331081 |
| Деталь: | GEAR Z77R Z23L |
| Парткод: | 303NN31040 |
| Деталь: | GEAR Z33R Z44R |
| Парткод: | 303NN31070 |
| Деталь: | HOLDER DRIVE LOW B |
| Парткод: | 302MV31020 |
| Деталь: | SPRING FEED |
| Парткод: | 302HN31410 |
| Деталь: | SPRING JOINT SHAFT |
| Парткод: | 303NN31080 |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | 302HN31660 |
| Деталь: | WIRE FEED DRIVE |
| Парткод: | 302RH46020 |
| Деталь: | DR-8315D |
| Парткод: | 302MV93110 |
| Деталь: | BASE CONVEYING |
| Парткод: | 302K324011 |
| Деталь: | TERMINAL TRANSFER |
| Парткод: | 302K324080 |
| Деталь: | GUIDE CONVEYING |
| Парткод: | 302NL24090 |
| Деталь: | SPRING EARTH CONVEYING |
| Парткод: | 302K324130 |
| Деталь: | SPRING CONVEYING R |
| Парткод: | 302K324360 |
| Деталь: | LEVER CONVEYING R |
| Парткод: | 302K324070 |
| Деталь: | SPRING CONVEYING F |
| Парткод: | 302K324110 |
| Деталь: | LEVER CONVEYING F |
| Парткод: | 302K324060 |
| Деталь: | BUSH REGIST R |
| Парткод: | 302K324270 |
| Деталь: | BUSH REGIST F |
| Парткод: | 302K324180 |
| Деталь: | PARTS ROLLER REGIST RIGHT SP |
| Парткод: | 302K394220 |
| Деталь: | COLLAR TRANS ROLLER |
| Парткод: | 302H722470 |
| Деталь: | PARTS GEAR REGIST Z24R SP |
| Парткод: | 302K394330 |
| Деталь: | SPRING REGIST R |
| Парткод: | 302K324440 |
| Деталь: | SPRING REGIST F |
| Парткод: | 302K324200 |
| Деталь: | SPRING REGIST C |
| Парткод: | 302K324500 |
| Деталь: | BUSH REGIST C |
| Парткод: | 302K324470 |
| Деталь: | WIRE DU |
| Парткод: | 302K346090 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | RETAINER ACTUATOR |
| Парткод: | 302K329060 |
| Деталь: | ACTUATOR DU |
| Парткод: | 302K329040 |
| Деталь: | FRAME DU |
| Парткод: | 302K329010 |
| Деталь: | PULLEY DU |
| Парткод: | 302K329020 |
| Деталь: | SPRING DU FEED |
| Парткод: | 302K329030 |
| Деталь: | COVER HARNESS |
| Парткод: | 302K324322 |
| Деталь: | TERMINAL SEPARATION B |
| Парткод: | 302K324340 |
| Деталь: | TERMINAL SEPARATION A |
| Парткод: | 302K324090 |
| Деталь: | FILM GUIDE REGIST |
| Парткод: | 302K324290 |
| Деталь: | FILM GUIDE FEED JUNCTION |
| Парткод: | 302NL24050 |
| Деталь: | GUIDE FEED JUNCTION |
| Парткод: | 302NL24040 |
| Деталь: | SPRING TRANSFER LIFT |
| Парткод: | 302K324510 |
| Деталь: | FILM CONVEYING SHAFT |
| Парткод: | 302K304630 |
| Деталь: | SHAFT RIGHT COVER R |
| Парткод: | 302K304560 |
| Деталь: | SHAFT RIGHT COVER F |
| Парткод: | 302K304550 |
| Деталь: | PARTS CONVEYING UNIT SP |
| Парткод: | 302NL94070 |
| Деталь: | COVER ISU REAR |
| Парткод: | 302RH04130 |
| Деталь: | COVER ISU RIGHT |
| Парткод: | 302RH04120 |
| Деталь: | COVER ISU LEFT |
| Парткод: | 302RH04110 |
| Деталь: | COVER ISU LEFT SUB |
| Парткод: | 302RH04230 |
| Деталь: | LABEL OPERATION CAUTION A |
| Парткод: | 302RH34040 |
| Деталь: | LABEL OPERATION CAUTION B |
| Парткод: | 302RH34050 |
| Деталь: | COVER ISU FRONT A |
| Парткод: | 302RH04100 |
| Деталь: | LID DP |
| Парткод: | 302RH04330 |
| Деталь: | GUIDE RIGHT COVER |
| Парткод: | 302K304531 |
| Деталь: | BUSH 8 EW |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | SHAFT DU |
| Парткод: | 302K329220 |
| Деталь: | PARTS GEAR DU Z27L SP |
| Парткод: | 302K394400 |
| Деталь: | PULLEY DU 26 |
| Парткод: | 302K329280 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | BELT DU A |
| Парткод: | 302K329240 |
| Деталь: | BELT DU B |
| Парткод: | 302K329250 |
| Деталь: | PARTS ROLLER DU SP |
| Парткод: | 302K394250 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | BUSH DU |
| Парткод: | 302K329270 |
| Деталь: | SPRING HOOK |
| Парткод: | 302K304540 |
| Деталь: | JOINT JUNCTION HOOK |
| Парткод: | 302K304571 |
| Деталь: | WIRE EARTH DU |
| Парткод: | 302K329230 |
| Деталь: | COVER RIGHT MIDDLE |
| Парткод: | 302RH04370 |
| Деталь: | LABEL COVER CAUTION |
| Парткод: | 302MV34250 |
| Деталь: | LABEL BYPASS CAUTION |
| Парткод: | 302MV34260 |
| Деталь: | HOOK RIGHT COVER |
| Парткод: | 302K304520 |
| Деталь: | COVER RIGHT HOOK |
| Парткод: | 302MV04300 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | LABEL HIGH TEMP |
| Парткод: | 302MV34400 |
| Деталь: | GUIDE EXIT RIGHT |
| Парткод: | 302K328200 |
| Деталь: | PULLEY DU |
| Парткод: | 302K329020 |
| Деталь: | SPRING DU FEED |
| Парткод: | 302K329030 |
| Деталь: | STRAP RIGHT COVER |
| Парткод: | 302K304591 |
| Деталь: | PARTS RIGHT COVER UNIT SP |
| Парткод: | 302RH94190 |
| Деталь: | PARTS TABLET OPERATION SP |
| Парткод: | 302RH94070 |
| Деталь: | PARTS LCD OPERATION SP |
| Парткод: | 302RH94060 |
| Деталь: | SPONGE LCD A |
| Парткод: | 302RH05210 |
| Деталь: | SPONGE LCD B |
| Парткод: | 302RH05220 |
| Деталь: | SPONGE LCD C |
| Парткод: | 302RH05230 |
| Деталь: | SPONGE LCD D |
| Парткод: | 302RH05240 |
| Деталь: | PARTS PWB NFC ASSY SP |
| Парткод: | 302RH94050 |
| Деталь: | PARTS PWB OPERATION ASSY SP |
| Парткод: | 302RH94040 |
| Деталь: | PARTS PWB PANEL MAIN ASSY SP |
| Парткод: | 302RH94030 |
| Деталь: | SHEET OPERATION |
| Парткод: | 302RH05340 |
| Деталь: | SHEET OPERATION JP |
| Парткод: | 302RH05350 |
| Деталь: | HOLDER WIRE OPERATION |
| Парткод: | 302RH05370 |
| Деталь: | PARTS SPEAKER SP |
| Парткод: | 302RH94100 |
| Деталь: | HOLDER SPEAKER |
| Парткод: | 302RH05290 |
| Деталь: | PARTS PWB USB HUB ASSY SP |
| Парткод: | 302RH94020 |
| Деталь: | COVER OPERATION D |
| Парткод: | 302RH05360 |
| Деталь: | WIRE USB HUB |
| Парткод: | 302RH46150 |
| Деталь: | WIRE MAIN-OPERATION |
| Парткод: | 302RH46140 |
| Деталь: | WIRE PANEL DATA |
| Парткод: | 302RH46130 |
| Деталь: | CUSHION HOLDER |
| Парткод: | 303H321120 |
| Деталь: | PARTS OPERATION UNIT SP |
| Парткод: | 302RH94140 |
| Деталь: | STAY RIGHT HANDLE |
| Парткод: | 302K302141 |
| Деталь: | GUIDE FEED INNER |
| Парткод: | 302MV07040 |
| Деталь: | SENSOR OPT |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | BASE MPF |
| Парткод: | 302MV08010 |
| Деталь: | PARTS PAD SEPARATION ASSY SP |
| Парткод: | 302RH94180 |
| Деталь: | SEAL SIDE MPF |
| Парткод: | 302K308480 |
| Деталь: | WIRE MPF SIZE UNIT 1 |
| Парткод: | 302MV46450 |
| Деталь: | WIRE MPF |
| Парткод: | 302MV46580 |
| Деталь: | ACTUATOR MPF |
| Парткод: | 302K308020 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | 302K308250 |
| Деталь: | SPRING LIFT R |
| Парткод: | 302RH08080 |
| Деталь: | SPRING LIFT F |
| Парткод: | 302RH08070 |
| Деталь: | LIFT PLATE |
| Парткод: | 302K308101 |
| Деталь: | PAD LIFT |
| Парткод: | 302K308110 |
| Деталь: | SEAL GUIDE PAD |
| Парткод: | 302K308340 |
| Деталь: | ARM LIFT |
| Парткод: | 302K308140 |
| Деталь: | SPRING EARTH |
| Парткод: | 302K308240 |
| Деталь: | GUIDE UPPER MPF |
| Парткод: | 302K308030 |
| Деталь: | WIRE EARTH MPF |
| Парткод: | 302K308260 |
| Деталь: | BUSH 10 |
| Парткод: | 302K308070 |
| Деталь: | LABEL J |
| Парткод: | 302MV34190 |
| Деталь: | SHAFT MPF |
| Парткод: | 302K308080 |
| Деталь: | PARTS GEAR MPF Z28 SP |
| Парткод: | 302K394320 |
| Деталь: | ROLLER MPF |
| Парткод: | 302K308150 |
| Деталь: | PULLEY MPF |
| Парткод: | 302MV08030 |
| Деталь: | SPRING MPF ROLL |
| Парткод: | 302K308270 |
| Деталь: | PIN FEED ROLL |
| Парткод: | 302MV08020 |
| Деталь: | COVER MPF WIRE |
| Парткод: | 302MV08050 |
| Деталь: | PARTS MPF UNIT SP |
| Парткод: | 302RH94200 |
| Деталь: | PARTS ROLLER MPF ASSY SP |
| Парткод: | 302MV94021 |
Коды ошибок
0030
0060
0070
0100
0120
0130
0140
0150
0160
0170
0180
0350
0640
0650
0660
0670
0680
0800
0830
0840
0870
0920
0980
1010
1020
1030
1040
1100
1110
1800
1900
2000
2010
2500
2510
2600
2610
3100
3200
3210
3300
3310
3500
3600
3800
3900
4001
4011
4101
4201
4700
5101
6020
6030
6200
6220
6230
6250
6400
6910
7200
7210
7800
7810
7901
7911
8010
8020
8030
8090
8100
8110
8120
8130
8140
8150
8160
8170
8180
8190
8200
8210
8230
8240
8250
8260
8410
8420
8430
8500
8510
8520
8800
8900
8990
9000
9010
9040
9050
9060
9070
9080
9100
9110
9120
9130
9140
9150
9160
9170
9180
9500
9510
F000
F010
F020
F021
F022
F040
F041
F050
F051
F052
Описание
| Error code: | 0030 |
| Description: | FAX control PWB system error Processing with the fax software was disabled due to a software problem. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Reinstall the fax software. 3. Replace the FAX control PWB. |
| Error code: | 0060 |
| Display: | FUSER MOTOR |
| Description: | Engine PWB mismatch Unmatching engine and engine sub boards. Defective engine subboard |
| Causes: | Defective engine sub PWB. |
| Remedy: | Engine PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Replace the engine PWB. |
| Error code: | 0070 |
| Description: | FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX control PWB (The FAX PWB installed will not be the one designed for the machine.) 1. Install the FAX system designed for the model. 2. Reinstall the fax software. |
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0120 |
| Description: | There is a problem with Thermistor for Pre-Heater. |
| Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0130 |
| Description: | There is a problem with Thermistor for Print Heater. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0140 |
| Description: | There is a problem with Thermistor for dryer. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0180 |
| Description: | Even though the machine carries out the regular movement, the output of Maintenance Liquid Pump Sensor does not reach the expected value. |
| Causes: | Maintenance Liquid Pump Motor has a problem. Maintenance Liquid Pump Sensor has a problem. Maintenance Liquid Pump Magnet has dropped out. Wiring or Flexible Cable has short circuitted |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Maintenance Liquid Pump Motor replacement Maintenance Liquid Pump Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0350 |
| Description: | Panel PWB communication error (electronic volume I2C communication error) NACK is received during I2C communication -> retried 5 times -> rebooting command sent -> retried 5 times If NACK is still received. |
| Causes: | Operation PWB. Main PWB |
| Remedy: | Operation PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Operation PWB (YC10) and Main PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. Main PWB Replace the main PWB. |
| Error code: | 0640 |
| Description: | Hard disk error The hard disk cannot be accessed. |
| Causes: | Defective hard disk. Defective main PWB. |
| Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Lack of HDD capacity 1. Confirm the total capacity of the HDD if it is more than 320GB. Change the HDD or add it in case of lacking in capacity. Main PWB Replace the main PWB. |
| Error code: | 0650 |
| Display: | Scanner home failure CODE (0650) Turn power off, on |
| Description: | Scanner Home Failure • A low motor lock signal is not detected even after the lapse of a predetermined period of time after the Polygon Motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the Polygon Motor remains energized. |
| Causes: | • Engine Control Board, PL13.0.20 • Image Processor Board, PL2.0.4 |
| Remedy: | 1 Check connector P/J2 on the Image Processor Board. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Replace the Scanner. Does the problem persist? Go to step 3. Complete. 3 Replace the Engine Control Board. Does the problem persist? Go to step 4. Complete. 4 Replace the Power Supply. Complete. |
| Error code: | 0660 |
| Description: | Hard disk encryption key error |
| Causes: | EEPROM. HDD. Main PWB |
| Remedy: | EEPROM 1. Execute U004 if this occurs after the EEPROM has been changed. HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
| Error code: | 0670 |
| Description: | Hard disk overwriting erasure error |
| Causes: | HDD. Main PWB. |
| Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
| Error code: | 0680 |
| Description: | SSD error In case of inability of communication with the SSD. (for 35 ppm model only) |
| Causes: | SSD, Main PWB |
| Remedy: | SSD: 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Unplug the power cord from the wall outlet, and reinstall the SSD. 3. Check the connection failure between the KUIO connector of the main PWB and SSD, and reconnect it. 4. Initialize the SSD. |
| Error code: | 0800 |
| Display: | Print Unable 08 Turn the power off and then back on again. |
| Description: | Image processing error JAM010X is detected twice. |
| Causes: | Defective main PWB. |
| Remedy: | Main PWB Replace the main PWB. |
| Error code: | 0830 |
| Description: | FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX software 1. Reinstall the fax software. FAX control PWB 1. Execute initializing by U600.(Refer to the FAX service manual) 2. Replace the FAX control PWB. |
| Error code: | 0840 |
| Description: | Faults of RTC (“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check. After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T.’ |
| Causes: | The battery is disconnected from the main PWB Defective main PWB. |
| Remedy: | Battery (main PWB) 1. Make sure that the back-up batteries on the main PWB are not short-circuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main circuit PWB, check the PWB is properly grounded. Main PWB Replace the main PWB |
| Error code: | 0870 |
| Description: | PCFAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. |
| Causes: | Improper installation FAX control PWB. Defective FAX control PWB or main PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Replace the FAX control PWB. HDD Execute U024 to initialize the HDD. Main PWB Replace the main PWB. |
| Error code: | 0920 |
| Description: | Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Execute initializing by U600 (Refer to the FAX service manual). 2. Replace the FAX control PWB. |
| Error code: | 0980 |
| Description: | 24 V power down detect If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second. |
| Causes: | Defective power source PWB. |
| Remedy: | Power source PWB 1. Check the +24V output is given at YC12- 1 to 3 of the power circuit PWB. 2. Replace the power source PWB |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1030 |
| Display: | GARO W1221 |
| Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1040 |
| Display: | GL2: W0501 The memory is full. |
| Description: | PF lift motor 2 error (paper feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 2. Replace the PF lift motor 2. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1100 |
| Display: | Prepare for maint cart replacement. |
| Description: | Paper Jam There is paper jammed in the All-In-One. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Clear the paper jam, and resend the print job. |
| Error code: | 1110 |
| Description: | PF lift motor 2 error (large capacity feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively. However, the first 1 s after PF lift motor 2 is turned on is excluded from detection. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 2 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF Lift motor2. PF Lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor 2 and PF main PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the PF Lift sensor 2. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1800 |
| Description: | Paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
| Remedy: | Paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1900 |
| Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2000 |
| Description: | DDA Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 2010 |
| Display: | Paper loaded askew. Press Load/Eject and reload the paper. |
| Description: | Main motor startup error Main motor is not stabilized within 1 s since the motor is activated. |
| Causes: | Main motor. Engine PWB |
| Remedy: | Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC13) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2510 |
| Description: | Paper feed motor startup error Paper feed motor is not stabilized within 1 s since the motor is activated. |
| Causes: | Paper feed motor. Engine PWB |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Engine PWB (YC13) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2600 |
| Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2610 |
| Description: | PF paper feed motor error (paper feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 2PF - Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 3100 |
| Description: | Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor. |
| Causes: | Defective connector cable or poor contact in the connector. Defective home position sensor. Defective scanner motor. Defective ISC PWB. Defective main PWB. |
| Remedy: | The scanner mirror frame is being locked after setup. Check whether the scanner mirror frame has been unlocked and unlock if necessary. Scanner motor 1. To check the scanner motor, execute U073. 2. Move the scanner by the hand to check whether it is unusually difficult to move. 3. Check that the optical wire rope is not disengaged and engage the wire. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and Main PWB (YC11) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the scanner motor. Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Home position sensor and ISC PWB (YC8) 3. Replace the home position sensor. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3200 |
| Description: | Exposure lamp error When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LED lamp PWB. Defective ISC PWB. Defective main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and main PWB (YC11) Defective LED lamp PWB. Replace the LED lamp PWB and check for correct operation. Defective ISC PWB. Replace the ISC PWB and check for correct operation. Defective CCD PWB. Replace the ISU and check for correct operation. Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | 3210 |
| Description: | CIS lamp error When input value at the time of CIS illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Execute CCD of U061 lamp check. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. DP relay PWB Replace the DP relay PWB. |
| Error code: | 3300 |
| Description: | Optical system (AGC) error One of the gains is FF or 00 during the CCD lamp AGC is being processed. |
| Causes: | Defective connector cable or poor contact in the connector. Defective exposure lamp Defective CCD PWB. Defective ISC PWB. Defective main PWB. |
| Remedy: | LED lamp PWB 1. To check the lamp, execute U061 CCD. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. If the LED lamp won’t light, replace the LED PWB and execut U411. CCD PWB Replace the ISU and execute U411. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3310 |
| Description: | CIS AGC error After AGC, correct input is not obtained at CIS. |
| Causes: | Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. To check the lamp, execute U061 CCD. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. |
| Error code: | 3500 |
| Description: | Communication error between scanner and ASIC An error code is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective ISC PWB. Defective main PWB. |
| Remedy: | ISC PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ISC PWB (YC3) and Main PWB (YC11) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3600 |
| Description: | Scanner sequence error |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Execute U021 memory initializing. 2. Replace the ISC PWB and execute U411. |
| Error code: | 3800 |
| Description: | AFE error When writing the data, read and write data does not match 3 times in succession. No response is received in 100 ms from AEF. |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. CCD PWB (YC2) and ISC PWB (YC9) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the ISC PWB and execute U411. CCD PWB Replace the ISU and execute U411. |
| Error code: | 3900 |
| Description: | Backup memory read/write error (ISC PWB) Read and write data does not match. |
| Causes: | Defective backup memory or PWB. |
| Remedy: | Backup memory (ISC PWB) 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Replace the ISC PWB and execute U411. |
| Error code: | 4001 |
| Display: | ERROR E146-4001 Call for service. |
| Description: | Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4011 |
| Description: | Polygon motor steady-state error After Polygon motor is stabilized, the ready signal is at the H level for 15 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4101 |
| Description: | BD initialization error K After Polygon motor is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4201 |
| Display: | Replace Drum:BK |
| Description: | BD steady-state error K The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, shorted or grounded, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4700 |
| Display: | Supplies WT Box End Soon |
| Description: | VIDEO_ASIC device error Communication with the video ASIC has failed 5 times successively. After writing to the VIDEO ASIC, the error that the reading value from the same address does not match occurs 8 times successively. |
| Causes: | Engine PWB. Main PWB |
| Remedy: | Main PWB 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Check that the connectors on the main PWB are properly connected, and if not, re-connect them. 3. Replace the main PWB. |
| Error code: | 5101 |
| Description: | Main high-voltage error K Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board). |
| Causes: | Defective connector cable or poor contact in the connector. Defective high voltage PWB Defective engine PWB. |
| Remedy: | Drum unit 1. Confirm that the drum or the drum screw can rotate. 2. If it won’t rotate, replace the drum unit. 3. Check that the discharger lamp is properly connected. Charger roller unit 1. Check that the high-voltage contacts are not distorted or adhered with foreign objects. 2. Reinstall the chrager roller unit.Or, replace the charger roller unit. High voltage PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. High voltage PWB (YC2) and Engine PWB (YC16) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the High voltage PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6200 |
| Display: | No Drum Unit Install the Drum Unit. |
| Description: | Broken fuser edge heater wire Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser center thermistor 1 1. Replace the Fuser unit. |
| Error code: | 6220 |
| Description: | Abnormally high fuser edge thermistor temperature Fuser thermistor 2 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 2. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6230 |
| Description: | Broken fuser edge thermistor wire The Input signal from the fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s when the temperature at the fuser thermistor 1 is higher than 100°C/212°F. Fuser thermistor 2 detects a lower then 50°C/122°F for 15s during warming up. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 2 wire. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6250 |
| Description: | Abnormally low fuser edge thermistor temperature Fuser thermistor 2 detects a temperature lower than 100°C/212°F for 1 s during ready or print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 2. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Fuser unit and Engine PWB (YC26) If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 6910 |
| Description: | Engine software ready error The device won’t engage in ready state in 60 minutes after warming-up has began. (A previous timeout process has not been cancelled. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser rear fan motor. Defective engine PWB. |
| Remedy: | Engine PWB 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Reinstall the engine software. 3. Replace the engine PWB. |
| Error code: | 7200 |
| Display: | Jam MP Tray Remove the jammed paper from MP Tray and press [Retry]. |
| Description: | Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7210 |
| Description: | Short-circuited outer temperature sensor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7810 |
| Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 7901 |
| Description: | Drum EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB. |
| Remedy: | DR PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7911 |
| Description: | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit. |
| Remedy: | Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8010 |
| Description: | Punch motor error 1 When the punch motor is driven, punch home position sensor does not turn on within 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch home position sensor. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch home position sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch home position sensor and Punch PWB (YC8) 4. Replace the Punch home position sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8020 |
| Description: | Punch motor error 2 Home position is not obtained in 3 s after home position is initialized or in standby. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8030 |
| Description: | Punch motor error 3 Home position does not turn from On to Off in 50 ms after home position has been initialized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8090 |
| Description: | DF paddle motor error When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF paddle sensor. Defective DF paddle motor. Defective DF main PWB. |
| Remedy: | DF paddle motor 1. Execute U240 Motor - Beat to check the finisher operation. 2. Check that the paddle can rotate. 3. Check that the drive from the motor reaches the paddle. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle motor and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF paddle motor. DF paddle sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle sensor and DF main PWB (YC22) 4. Replace the DF paddle sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8100 |
| Description: | DF eject release motor error When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF bundle discharge sensor. Defective DF eject release motor. Defective DF main PWB. |
| Remedy: | DF eject release motor DF bundle discharge unit sensor 1. Execute U240 Motor - Eject Unlock (Full) to check the finisher operation. 2. Check that the eject guide of the process tray is opened and, if not, correct the guide. 3. Check that the drive from the motor reaches the eject guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF eject release motor. DF bundle discharge unit sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 4. Replace the DF bundle eject unit sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8110 |
| Description: | DF shift motor 1 error DF shift sensor 1 won’t turn on when it has travelled 160 mm after DF shift motor 1 is driven. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF shift sensor 1. Defective DF shift motor 1. Defective DF main PWB. |
| Remedy: | DF shift motor 1 [front] 1. Execute U240 Motor - Sort Test to check the finisher operation. 2. Manipulate the front shift guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front shift guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift motor 1[front] and DF main PWB (YC14) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF shift motor 1 [front]. DF shift sensor 1 [front] 1. Execute U241 Finisher - Shift Front HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift sensor 1[front] and DF main PWB (YC23) 4. Replace the DF shift sensor 1 [front]. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8120 |
| Description: | DF shift motor 2 error DF shift sensor 2 won’t turn on when it has travelled 160 mm after DF shift motor 2 is driven. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF shift sensor 2. Defective DF shift motor 2. Defective DF main PWB. |
| Remedy: | DF shift motor 2 [rear] 1. Execute U240 Motor - Sort Test to check the finisher operation. 2. Manipulate the rear shift guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear shift guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift motor 2 [rear] and DF main PWB (YC14) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF shift motor 2 [rear]. DF shift sensor 2 [rear] 1. Execute U241 Finisher - Shift Tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift sensor 2 [rear] and DF main PWB (YC23) 4. Replace the DF shift set sensor2 [rear]. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8130 |
| Description: | DF shift release motor error When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF shift release sensor. Defective DF shift release motor. Defective DF main PWB. |
| Remedy: | DF shift release motor 1. Check that cancelling the maintenance mode after executing U240 Motor - Sort for the finisher operation check lets the rear and forth cursors return to the home position. 2. Manipulate the front and rear shift guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the shift guide front and rear. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift release motor and DF main PWB (YC14) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF shift release motor. DF shift release sensor 1. Execute U241 Finisher - Shift Unlock HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift release sensor and DF main PWB (YC23) 4. Replace the DF shift release sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8140 |
| Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8150 |
| Description: | DF tray motor error 2 When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF main PWB (YC22) DF tray upper surface sensor and DF main PWB (YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8160 |
| Description: | DF tray motor error 3 When the main tray has descended, DF tray sensor 4 does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF tray sensor 3. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 4 1. Execute U241 Finisher - Tray Middle to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 4 and DF main PWB (YC23) 4. Replace the DF tray sensor 4. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8170 |
| Description: | DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8180 |
| Description: | DF side registration motor 1 error 2 JAM6810 (jam in front of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1. 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8190 |
| Description: | DF side registration motor 2 error 1 When initial operation, DF side registration sensor 2 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
| Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8200 |
| Description: | DF side registration motor 2 error 2 JAM6910 (jam in rear of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
| Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8210 |
| Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
| Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8230 |
| Description: | DF staple motor error 1 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF staple sensor Replace the staple unit. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8240 |
| Description: | DF staple motor error 2 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8250 |
| Description: | DF tray motor error 4 The lock signal of the motor is detected continuously for 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF tray motor and DF main PWB (YC16) DF tray sensor 3 and DF main PWB (YC23) Defective DF tray motor. Replace the DF tray motor. Defective DF main PWB. Replace the DF main PWB and check for correct operation. |
| Error code: | 8260 |
| Description: | DF middle motor home position error DF paddle sensor is not turned on within 1s after driving the DF middle motor. |
| Causes: | DF middle motor. DF paddle sensor. DF main PWB |
| Remedy: | DF middle motor 1. Execute U240 Motor - Middle(H)(L). 2. Check that the drive from the motor reaches the paddle. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF middle motor and DF main PWB (YC12) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF middle motor. DF paddle sensor 1. Execute U241 Finisher - Lead Paddle to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF paddle sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8410 |
| Description: | Punch slide motor error 1 The punch slide sensor won’t turn On when home position has been moved by 30 mm. |
| Causes: | Defective connector cable or poor contact in the connector. Defective slide sensor. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch slide sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide sensor and Punch PWB (YC6) 4. Replace the punch slide sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8420 |
| Description: | Punch slide motor error 2 In detection of paper edges, the paper edge cannot be detected in 30 mm move. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch paper edge sensor 1,2 1. Execute U241 Punch - Edge Face 1,2,3,4 to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch paper edge sensor 1,2 and Punch PWB (YC5,YC7) 4. Replace the punch paper edge sensor 1,2. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8430 |
| Description: | Punch unit communication error Communication with the punch unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8500 |
| Description: | Mailbox communication error Communication failed to be established after the mailbox was hooked up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | MB main PWB 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB main PWB (YC3) and DF main PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB main PWB DF main PWB Replace the DF main PWB |
| Error code: | 8510 |
| Description: | MB conveying motor error 1 When initial operation, MB home position sensor does not turn on within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor. Defective MB main PWB. |
| Remedy: | MB conveying motor 1. If the transfer roller won’t rotate smoothly, repair its mechanism. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
| Error code: | 8520 |
| Description: | MB conveying motor error 2 When standby operation, MB home position sensor does not turn off within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor Defective MB main PWB. |
| Remedy: | MB conveying motor 1. Execute Mail Box - Conv of U240 finisher operation check. 2. Manipulate the conveying roller of the mailbox to check it can smoothly rotate. 3. Check that the drive from the motor reaches the conveying roller. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
| Error code: | 8800 |
| Description: | Document finisher main program error Document finisher main program error at power up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8900 |
| Description: | Document finisher backup error Read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective DF main PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB |
| Error code: | 8990 |
| Description: | Finisher setup error In case the bridge (AK) is not installed while the DF is connected. (35/40 ppm model only) |
| Causes: | Bridge unit Document finisher. DF main PWB. Engine PWB |
| Remedy: | Finisher 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DF main PWB - Engine PWB(YC24): 30 ppm model - Engine PWB(YC31): 35/40 ppm models 2. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. DF main PWB 1. Check EEPROM mount and correct it. 2. Replace the DF main PWB. |
| Error code: | 9000 |
| Description: | Document processor communication error Communication with the document processor is not possible. |
| Causes: | Defective connector cable or poor contact in the connector Defective PWB. |
| Remedy: | DP main PWB 1. Check that the versions of the main unit firmware and the DP firmware are identical. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP main PWB(YC1) and ISC PWB(YC12) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP main PWB ISC PWB Replace the ISC PWB. |
| Error code: | 9010 |
| Description: | Coin vender communication error A communication error from coin vender is detected 10 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Data setup failure. Defective coin vender control PWB. Defective PWB. |
| Remedy: | U206 setting Set maintenance mode U206 to off when a coin vender is not installed. Coin vender control PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Coin vender control PWB and Engine PWB (YC23) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Coin vender control PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 9040 |
| Description: | DP lift motor going up error When the DP lift motor is driven, DP lift sensor 1 does not turn on within 1500 pulse. (Three recovery times.) The above has been detected 5 times. * : The number of detection should be weighted with one for the rise at job start and two for the irregular rise during transporting. The accumulated number must be cleared at completion of a normal rise. The default threshold is 5. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DP lift sensor 1. Defective DP lift motor. Defective DP main PWB. |
| Remedy: | DP lift motor 1. Execute U906 Separating Operation Release. 2. Execute U243 Lift Motor to check the DP motor operation. 3. Check that the original document lift guide can move upwards. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift motor and DP main PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DP lift motor. DP lift sensor 1 1. Execute U244 Lift L-Limit to check DP switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift sensor 1 and DP main PWB (YC4) 4. Replace the DP lift sensor 1. DP main PWB Replace the DP main PWB |
| Error code: | 9050 |
| Description: | DP lift motor going down error When the DP lift motor is driven, DP lift sensor 2 does not turn on within 1500 pulse. (Three recovery times.) The above has been detected 1 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DP lift sensor 2. Defective DP lift motor. Defective DP main PWB. |
| Remedy: | DP lift motor 1. Execute U906 Separating Operation Release. 2. Execute U243 Lift Motor to check the DP motor operation. 3. Check that the original document lift guide can move downwards. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift motor and DP main PWB (YC5) If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DP lift motor. DP lift sensor 2 1. Execute U244 Lift L-Limit to check DP switch. 2. Confirm that the DP lift sensor 2 has been firmly fitted. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift sensor 2 and DP main PWB (YC2) 4. Replace the DP lift sensor2. DP main PWB Replace the DP main PWB |
| Error code: | 9060 |
| Description: | DP EEPROM error Mismatch of reading data from two locations occurs 3 times successively. Mismatch between writing data and reading data occurs 3 times successively. |
| Causes: | Defective DP main PWB. Device damage of EEPROM. |
| Remedy: | DP main PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the EEPROM has been properly installed. 3. Replace the DP main PWB Device damage of EEPROM Contact the Service Support. |
| Error code: | 9070 |
| Description: | Communication error between DP and SHD A communication error is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DPSHD PWB. |
| Remedy: | DP SHD PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP SHD PWB (YC1) and DP main PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP SHD PWB. |
| Error code: | 9080 |
| Description: | LED fault detection A block is existent below a peak which was obtained by activating the LEDs in the four CIS blocks at power on, which is less than 80hex. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS Defective DPSHD PWB. |
| Remedy: | DP CIS 1. Execute CIS automatic original document alignment by U411. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DP SHD PWB (YC2) DP SHD PWB (YC1) and DP main PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the CIS and execute U411. DP SHD PWB Replace the DP SHD PWB. |
| Error code: | 9100 |
| Description: | Coin vender control PWB error Communication error has been detected at the coin mec of the coin vender control PWB. |
| Causes: | Defective coin vender control PWB. |
| Remedy: | Coin vender control PWB Replace the coin mec. |
| Error code: | 9110 |
| Description: | Coin vender rejector error Communication error has been detected in connection with the coin mec and the rejector. |
| Causes: | Rejector installed incorrectly. Defective rejector. |
| Remedy: | Rejector 1. Check that the rejector is firmly installed and, if not, install firmly. 2. Replace the rejector. |
| Error code: | 9120 |
| Description: | Sensor error in coin vender change (Yen 10) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9130 |
| Description: | Sensor error in coin vender change (Yen 50) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9140 |
| Description: | Sensor error in coin vender change (Yen 100) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9150 |
| Description: | Sensor error in coin vender change (Yen 500) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Change tube Check no exchange jam is observed at the outlet and, if necessary, repair it. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9160 |
| Description: | Coin vender pay-out error Coin is paid out despite the pay-out motor is determined not active. |
| Causes: | Defective pay-out motor. |
| Remedy: | Pay-out motor Replace the coin mec. |
| Error code: | 9170 |
| Description: | Coin vender pay-out sensor error Coin is paid out despite the pay-out motor is determined not active. |
| Causes: | Change jam at the pay-out. Defective pay-out motor. Defective pay-out sensor. |
| Remedy: | Pay-out area Check no exchange jam is observed at the outlet and, if necessary, repair it. Pay-out motor Replace the coin mec. Pay-out sensor Replace the coin mec. |
| Error code: | 9180 |
| Description: | DP feed-shift motor error The HP cannot be detected even after executing the HP detection retrial 3 consecutive times. HP detection: when the DP feed-shift motor is driven to move to the HP, the HP is not detected after it is rotated once. |
| Causes: | DP feed-shift motor. DP feed-shift sensor |
| Remedy: | DP feed-shift motor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Confirm that the connector of the DP feed-shift motor is firmly connected, and if necessary, push the unit all the way in. 3. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DP feed-shift motor - Engine PWB (YC6) 4. If the wire is disconnected, short-circuited or has a ground fault, or the connector pin is deformed, replace the wire. 5. Replace the DF feed-shift motor. DP feed-shift sensor 1. Rotate the DP feed-shift motor manually to check that it is not unusually difficult to rotate. 2. Check if the DP feed-shift sensor is out of position because it has dropped off and if the sensor light is interrupted by the actuator. 3. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DP feed-shift sensor - DP main PWB (YC4) DP main PWB - Engine PWB (YC6) 4. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. 5. Replace the DP feed-shift sensor. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 9500 |
| Description: | ISC PWB error A |
| Causes: | Main PWB. ISC PWB. |
| Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC PWB 4. Contact the Service Support. |
| Error code: | 9510 |
| Description: | ISC PWB error B |
| Causes: | Main PWB. DP SHD PWB. |
| Remedy: | Main PWB DP SHD PWB 1. Reinsert the connector if its connection is loose. DP relay PWB (YC2) and DP SHD PWB (YC3) 2. Replace the main PWB. 3. Replace the DP SHD PWB. 4. Contact the Service Support. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F021 |
| Description: | System memory error (RAM reading/writing error or ASIC memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the main PWB ASIC when the main unit starts up. |
| Remedy: | 1 Resetting the main power The main PWB does not properly start up. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F022 |
| Description: | System memory error (RAM reading/writing error or ASIC memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the DP relay PWB ASIC when the main unit starts up. |
| Remedy: | 1 Resetting the main power The main PWB does not properly start up. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. 3 Checking the DP relay PWB The DP relay PWB is not properly connected or attached. Reattach the DP relay PWB and secure it with the screws. If not repaired, replace the DP relay PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F041 |
| Description: | Over than available setting number tray detection error |
| Causes: | Over than available setting number tray is installed. |
| Remedy: | Remove the available setting number tray. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F051 |
| Description: | Scanner engine program error |
| Causes: | The scanner program cannot start up |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The scanner engine RAM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the SSD The SSD is not properly attached. Reattach the SSD. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F052 |
| Description: | Panel engine program error |
| Causes: | The panel program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the panel firmware to the latest version. Firmware Update 2 Resetting the main power The panel RAM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the connection The connector is not properly connected or the wire is faulty. Clean the connectors on the operation panel main PWB and reinsert the wire connectors. If there is no continuity, replace the wire. Wiring diagram 4 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
