Kyocera TASKalfa 308ci
Рейтинг
Модули
PAPER CASSETTE
Covers 1
DP Paper Conveying Section 1
Frames Rear 1
DP ASSY SP
Paper Feed Section 1
Operation Section
Frames Base
Covers 2
DP Paper Conveying Section 2
DP Drive Section and Electrical Components
Frames Left
TRANSFER SECTION
Frames Front
DP Table Assy
Laser Scanner Section
Electrical Components 3
Electrical Components 4
Frames Right
Exit Section 1
Exit Section 2
Electrical Components 1
Frames Top
DP Paper Feed Section
ELECTRICAL COMPONENTS 2
PAPER FEED SECTION 2
Frames Rear 2
SCANNER SECTION
Developer and Image Formation Section
DP Frames
Fuser Section
DP Covers
DRIVE SECTION 2
Paper Conveying Section 2
Paper Conveying Section 1
Drive Section 1
Paper Feed Section 3
Детали SCANNER SECTION
| Деталь: | BASE CASSETTE |
| Парткод: | 302 R409010 |
| Деталь: | CURSOR END |
| Парткод: | 302R409020 |
| Деталь: | PLATE TURN |
| Парткод: | 302R409030 |
| Деталь: | LEVER SIDE CURSOR |
| Парткод: | 302R409040 |
| Деталь: | SPRING CASSETTE EARTH |
| Парткод: | 302 R409050 |
| Деталь: | GEAR Z13S JOINT |
| Парткод: | 302R409060 |
| Деталь: | INDICATER PAPER LEVEL |
| Парткод: | 302R409070 |
| Деталь: | LID LIFT GEAR |
| Парткод: | 302R409080 |
| Деталь: | SHUTTER SIZE DETECTION |
| Парткод: | 302R409090 |
| Деталь: | JOINT SIZE DETECTION |
| Парткод: | 302R409100 |
| Деталь: | PLATE BOTTOM |
| Парткод: | 302R409110 |
| Деталь: | REINFORCEMENT CURSOR |
| Парткод: | 302R409120 |
| Деталь: | LABEL PAPER LIMIT |
| Парткод: | 302R434020 |
| Деталь: | LABEL CASSETTE OPERATION |
| Парткод: | 302R434030 |
| Деталь: | RAIL INNER CASSETTE RIGHT ASSY |
| Парткод: | 302R409300 |
| Деталь: | RAIL INNER CASSETTE LEFT ASSY |
| Парткод: | 302R409310 |
| Деталь: | WORKPLATE LIFT |
| Парткод: | 302NR09070 |
| Деталь: | CURSOR LEFT |
| Парткод: | 302NT09030 |
| Деталь: | CURSOR RIGHT |
| Парткод: | 302NT09040 |
| Деталь: | LEVER CURSOR SET |
| Парткод: | 302NT09050 |
| Деталь: | SPRING CURSOR SET |
| Парткод: | 302NT09060 |
| Деталь: | GEAR Z48S LIFT |
| Парткод: | 302NT09100 |
| Деталь: | PAD BOTTOM |
| Парткод: | 302F909211 |
| Деталь: | SPRING LEVER CURSOR |
| Парткод: | 302R409130 |
| Деталь: | SPRING FIX |
| Парткод: | 302HN09190 |
| Деталь: | SIZE FIX |
| Парткод: | 302HN09240 |
| Деталь: | GEAR CASSETTE /A-49 CASSETTE A4 |
| Парткод: | 5MVG127DN071 |
| Деталь: | PIN,CASSETTE WORK PLATE |
| Парткод: | 66007310 |
| Деталь: | LABEL CASSETTE 1 |
| Парткод: | 302R434040 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302R404210 |
| Деталь: | CT-5195 |
| Парткод: | 302R493031 |
| Деталь: | COVER TRAY REAR |
| Парткод: | 302R404161 |
| Деталь: | LID TRAY REAR |
| Парткод: | 302R404170 |
| Деталь: | COVER EXIT LEFT |
| Парткод: | 302R404190 |
| Деталь: | COVER EXIT |
| Парткод: | 302R428011 |
| Деталь: | COVER TRAY |
| Парткод: | 302R404140 |
| Деталь: | MOUNT DF FRONT |
| Парткод: | 302R402280 |
| Деталь: | COVER RIGHT LOWER |
| Парткод: | 302R404080 |
| Деталь: | Cover Right Rear |
| Парткод: | 302R404070 |
| Деталь: | COVER RIGHT TOP |
| Парткод: | 302R404050 |
| Деталь: | LID RIGHT TOP |
| Парткод: | 302R404180 |
| Деталь: | SPONGE RIGHT TOP |
| Парткод: | 302R404220 |
| Деталь: | COVER FRONT RIGHT |
| Парткод: | 302R404060 |
| Деталь: | COVER EXIT FRONT |
| Парткод: | 302R404030 |
| Деталь: | COVER FRONT |
| Парткод: | 302R404010 |
| Деталь: | COVER FRONT UPPER |
| Парткод: | 302R404020 |
| Деталь: | PLATE MAGNET |
| Парткод: | 302NL04270 |
| Деталь: | STRAP FRONT COVER |
| Парткод: | 302R404200 |
| Деталь: | COVER EXIT TOP |
| Парткод: | 302R404040 |
| Деталь: | COVER CONTROLLER LEFT |
| Парткод: | 302WL04010 |
| Деталь: | COVER LEFT LOWER |
| Парткод: | 302R404120 |
| Деталь: | COVER REAR LOWER |
| Парткод: | 302R404110 |
| Деталь: | COVER REAR RIGHT |
| Парткод: | 302R404090 |
| Деталь: | COVER REAR LEFT |
| Парткод: | 302R404100 |
| Деталь: | LID MAIN |
| Парткод: | 302V539041 |
| Деталь: | LABEL EMBLEM 308C |
| Парткод: | 302WL34010 |
| Деталь: | EMBLEM |
| Парткод: | 303R304051 |
| Деталь: | PLATE OPTION |
| Парткод: | 302RH39220 |
| Деталь: | COVER ISU REAR |
| Парткод: | 302R417180 |
| Деталь: | PLATE EARTH COVER TRAY |
| Парткод: | 302R402320 |
| Деталь: | SHEET COVER FRONT L |
| Парткод: | 302R434200 |
| Деталь: | SPONGE FFC |
| Парткод: | 302WL39020 |
| Деталь: | HOUSING CONVEYING |
| Парткод: | 3V2NM18110 |
| Деталь: | ACTUATOR TIMING |
| Парткод: | 3V2NM18260 |
| Деталь: | SPRING-TORSION SET |
| Парткод: | 302M518180 |
| Деталь: | PLATE EARTH B |
| Парткод: | 3V2NM18150 |
| Деталь: | PLATE EARTH A |
| Парткод: | 3V2NM18140 |
| Деталь: | PARTS ROLLER CONVEYING B SP |
| Парткод: | 303R394070 |
| Деталь: | PARTS ROLLER CONVEYING A SP |
| Парткод: | 303R394060 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | GEAR Z22S ONEWAY |
| Парткод: | 3V2NM18400 |
| Деталь: | ONE WAY CLUTCH /A-49 MPF A4 |
| Парткод: | 5AAVCLTCH018 |
| Деталь: | PARTS GEAR Z22S EXIT SP |
| Парткод: | 302K394350 |
| Деталь: | PARTS ROLLER EXIT SP |
| Парткод: | 303R394080 |
| Деталь: | PARTS ROLLER LOOP SP |
| Парткод: | 303R394090 |
| Деталь: | GEAR Z22S |
| Парткод: | 3V2NM18370 |
| Деталь: | GUIDE SEPARATE |
| Парткод: | 3V2NM18820 |
| Деталь: | LEVER SEPARATE |
| Парткод: | 3V2NM18860 |
| Деталь: | SPRING PICKUP |
| Парткод: | 302LV06040 |
| Деталь: | SHAFT PULLEY |
| Парткод: | 303M824200 |
| Деталь: | PULLEY CONVEYING BK |
| Парткод: | 303M824210 |
| Деталь: | HOLDER PULLEY |
| Парткод: | 3V2NM18900 |
| Деталь: | SHAFT LOOP |
| Парткод: | 303R324130 |
| Деталь: | LEVER LOOP B |
| Парткод: | 3V2NM18880 |
| Деталь: | GUIDE UPPER |
| Парткод: | 3V2NM18730 |
| Деталь: | SHAFT GUIDE READING |
| Парткод: | 303M824130 |
| Деталь: | PULLEY GUIDE READING |
| Парткод: | 303LL24190 |
| Деталь: | STATIC ELIMINATOR |
| Парткод: | 303LJ28040 |
| Деталь: | GEAR Z40S |
| Парткод: | 3V2NM18360 |
| Деталь: | BUSH PF |
| Парткод: | 3V2NM18090 |
| Деталь: | ACTUATOR PUSH |
| Парткод: | 3V2NM18060 |
| Деталь: | SPRING-COMPRESSION RELEASE |
| Парткод: | 3V2NM18100 |
| Деталь: | GEAR Z25L-Z18P |
| Парткод: | 302R431530 |
| Деталь: | GEAR Z16S-Z25P |
| Парткод: | 302R431540 |
| Деталь: | BELT S2M 244 |
| Парткод: | 302R431570 |
| Деталь: | BRACKET TERMINAL |
| Парткод: | 302R439310 |
| Деталь: | SPRING HV MAIN |
| Парткод: | 302R439320 |
| Деталь: | SPRING HV MAG |
| Парткод: | 302R439330 |
| Деталь: | SPRING HV SLEEVE |
| Парткод: | 302R439340 |
| Деталь: | LID TERMINAL |
| Парткод: | 302R439380 |
| Деталь: | SPRING DRUM PWB |
| Парткод: | 302R439390 |
| Деталь: | PARTS PWB DRUM DLP CONNECT ASSY SP |
| Парткод: | 302R694040 |
| Деталь: | SPRING DLP PWB |
| Парткод: | 302R439400 |
| Деталь: | RAIL MIDDLE TRANSFER R |
| Парткод: | 302R402510 |
| Деталь: | PIN CLN DRIVE A |
| Парткод: | 302R431730 |
| Деталь: | PIN CLN DRIVE B |
| Парткод: | 302R431740 |
| Деталь: | SPRING HOOK RAIL TRANSFER |
| Парткод: | 302 R402650 |
| Деталь: | SPRING CONTACT 2T |
| Парткод: | 302R439560 |
| Деталь: | SPRING TRANS K |
| Парткод: | 302R439410 |
| Деталь: | SPRING TRANS M |
| Парткод: | 302R439420 |
| Деталь: | SPRING TRANS C |
| Парткод: | 302R439430 |
| Деталь: | SPRING TRANS Y |
| Парткод: | 302R439440 |
| Деталь: | SPRING TRANS ARM |
| Парткод: | 302 R439450 |
| Деталь: | SPRING TRANS LEFT |
| Парткод: | 302R439460 |
| Деталь: | SHAFT CLN DRIVE |
| Парткод: | 302R431510 |
| Деталь: | GEAR Z15L |
| Парткод: | 302R431860 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | GEAR Z17R MIDDLE |
| Парткод: | 303K831070 |
| Деталь: | GEAR Z19L-Z14R TONNER SUPPLY |
| Парткод: | 302HN21200 |
| Деталь: | BRACKET TENSION PULLEY |
| Парткод: | 302R431580 |
| Деталь: | SPRING MAIN DRIVE A |
| Парткод: | 302K031410 |
| Деталь: | SHEET TENSION |
| Парткод: | 302R431600 |
| Деталь: | GEAR Z27L-Z21P |
| Парткод: | 302R431750 |
| Деталь: | BELT S2M 800 |
| Парткод: | 302R431560 |
| Деталь: | GEAR Z27R-Z21R |
| Парткод: | 302R431520 |
| Деталь: | PULLEY Z21P S2M |
| Парткод: | 302R431550 |
| Деталь: | PLLLEY TENSION |
| Парткод: | 302R431590 |
| Деталь: | PARTS TONER SUPPLY ASSY SP |
| Парткод: | 302R494141 |
| Деталь: | PARTS BRACKET TERMINAL ASSY SP |
| Парткод: | 302R494040 |
| Деталь: | DPASSY SP |
| Парткод: | 302R493011 |
| Деталь: | GEAR FEED Z26L |
| Парткод: | 302R406070 |
| Деталь: | PULLEY FEED ASSY |
| Парткод: | 302F906230 |
| Цена: | 750 ₽ |
| Деталь: | GEAR FEED Z30H |
| Парткод: | 302F906280 |
| Деталь: | PULLEY PICKUP ASSY |
| Парткод: | 302HN06080 |
| Цена: | 480 ₽ |
| Деталь: | SHAFT PULLEY FEED |
| Парткод: | 302K306100 |
| Деталь: | BUSH 4 |
| Парткод: | 302K306460 |
| Деталь: | HOLDER PICKUP |
| Парткод: | 302R406020 |
| Деталь: | BUSH PICKUP HOLDER |
| Парткод: | 302R406030 |
| Деталь: | BUSH DRIVE 8 |
| Парткод: | 302K331230 |
| Деталь: | RETARD ROLLER ASSY |
| Парткод: | 302F909171 |
| Цена: | 900 ₽ |
| Деталь: | FRAME FEED UPPER |
| Парткод: | 302R406010 |
| Деталь: | SHAFT FEED DRIVE |
| Парткод: | 302R406040 |
| Деталь: | SPRING PICKUP |
| Парткод: | 302R406050 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302R406060 |
| Деталь: | FRAME FEED LOW |
| Парткод: | 302R406100 |
| Деталь: | HOLDER RETARD |
| Парткод: | 302R406110 |
| Деталь: | FILM RETARD |
| Парткод: | 302R406120 |
| Деталь: | SPRING RETARD |
| Парткод: | 302R406130 |
| Деталь: | FRAME FEED |
| Парткод: | 302R424060 |
| Деталь: | PARTS ROLLER REGIST SP |
| Парткод: | 302SZ94090 |
| Деталь: | BUSH REGIST EW |
| Парткод: | 302HN24410 |
| Деталь: | GEAR Z19L REG REAR |
| Парткод: | 302HN24060 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | SPRING EARTH REGIST R |
| Парткод: | 302R424090 |
| Деталь: | GEAR Z25L |
| Парткод: | 302S018170 |
| Деталь: | BUSH FEED DRIVE |
| Парткод: | 302F931490 |
| Деталь: | SHEET REGIST FEED |
| Парткод: | 302NR06540 |
| Деталь: | HOLDER CLEANER REGIST |
| Парткод: | 302R424220 |
| Деталь: | SPRING FEED EARTH A |
| Парткод: | 302R424100 |
| Деталь: | SPRING FEED EARTH B |
| Парткод: | 302R424110 |
| Деталь: | GUIDE FEED LOW LEFT |
| Парткод: | 302R406600 |
| Деталь: | FILM FEED LOW |
| Парткод: | 302R406610 |
| Деталь: | PARTS CLEANER REGIST ASSY SP |
| Парткод: | 302R494120 |
| Деталь: | MOUNT TORQUE LIMITTER |
| Парткод: | 302SZ24020 |
| Деталь: | TORQUE LIMITTER REGIST |
| Парткод: | 302SZ24030 |
| Деталь: | PARTS PRIMARY FEED ASSY SP |
| Парткод: | 302R494210 |
| Деталь: | PARTS HOLDER PICK UP ASSY SP |
| Парткод: | 302R494170 |
| Деталь: | PLATE EARTH LCD |
| Парткод: | 302V505150 |
| Деталь: | PARTS TABLET OPERATION SP |
| Парткод: | 302NM94121 |
| Деталь: | PARTS LCD OPERATION SP |
| Парткод: | 302P194230 |
| Деталь: | CONN.CORD ASSY S04194 PANEL-OPERATION(L) |
| Парткод: | 302WL46070 |
| Деталь: | CONN.CORD ASSY S04193 PANEL-OPERATION(R) |
| Парткод: | 302WL46060 |
| Деталь: | FILM FFC LCD |
| Парткод: | 302R605120 |
| Деталь: | COVER OPERATION F |
| Парткод: | 302WL05010 |
| Деталь: | FILM OPERATION |
| Парткод: | 302R605150 |
| Деталь: | LENS LED |
| Парткод: | 3V2NM05300 |
| Деталь: | KEY ENERGY SAVER |
| Парткод: | 302R405140 |
| Деталь: | KEY LOGOUT |
| Парткод: | 302R405080 |
| Деталь: | KEY RESET |
| Парткод: | 3V2NM05110 |
| Деталь: | KEY STOP |
| Парткод: | 3V2NM05100 |
| Деталь: | KEY START |
| Парткод: | 302R405220 |
| Деталь: | KEY LEFT |
| Парткод: | 302SZ05030 |
| Деталь: | KEY HOME |
| Парткод: | 302R605100 |
| Деталь: | KEY 10 |
| Парткод: | 302R605060 |
| Деталь: | PARTS PWB OPERATION ASSY SP |
| Парткод: | 302WL94050 |
| Деталь: | SPRING EARTH LCD |
| Парткод: | 302H005620 |
| Деталь: | MOUNT OPERATION |
| Парткод: | 302WL05030 |
| Деталь: | CUSHION LCD |
| Парткод: | 302V505130 |
| Деталь: | PLATE EARTH ISU |
| Парткод: | 302K302A50 |
| Деталь: | SHEET FRAME CENTER |
| Парткод: | 302J502020 |
| Деталь: | CUSHION EJECT GUIDE |
| Парткод: | 303H321050 |
| Деталь: | PARTS PWB PANEL MAIN ASSY SP |
| Парткод: | 302WL94040 |
| Деталь: | HINGE OPERATION |
| Парткод: | 302R405201 |
| Деталь: | LID HINGE |
| Парткод: | 302R605090 |
| Деталь: | COVER OPERATION R |
| Парткод: | 302WL05020 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | LID PANEL |
| Парткод: | 302R605050 |
| Деталь: | COVER PANEL |
| Парткод: | 302SZ05040 |
| Деталь: | SHEET OPERATION EN |
| Парткод: | 302SZ05110 |
| Деталь: | SHEET OPERATION KDA EN |
| Парткод: | 302SZ05120 |
| Деталь: | LID OPERATION REAR |
| Парткод: | 302V505050 |
| Деталь: | HOLDER FULCRUM OPERATION |
| Парткод: | 302R405100 |
| Деталь: | PARTS OPERATION UNIT L SP |
| Парткод: | 302WL94060 |
| Деталь: | PULLEY FEED PF |
| Парткод: | 303NJ06070 |
| Деталь: | SHAFT GUIDE PULLEY |
| Парткод: | 302 R409380 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | FOOT |
| Парткод: | 302MV02190 |
| Деталь: | COVER INNER |
| Парткод: | 302R403530 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000007+H01 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302H004660 |
| Деталь: | HOLDER SPRING L |
| Парткод: | 302R403570 |
| Деталь: | SPRING HOOK L |
| Парткод: | 302R403550 |
| Деталь: | SPRING HOOK R |
| Парткод: | 302R403540 |
| Деталь: | GEAR EXIT JOINT Z26S |
| Парткод: | 2BL21390 |
| Деталь: | GEAR Z18S |
| Парткод: | 302R403350 |
| Деталь: | GEAR Z15L-Z18S |
| Парткод: | 302R403330 |
| Деталь: | PLATE DRIVE WTB |
| Парткод: | 302R403320 |
| Деталь: | PARTS,FAN IMAGE SP |
| Парткод: | 302FZ94660 |
| Деталь: | SEAL FAN MOTOR A |
| Парткод: | 302 R403630 |
| Деталь: | FILM FRONT FAN |
| Парткод: | 302R403660 |
| Деталь: | PLATE FRONT FAN |
| Парткод: | 302R403610 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | DUCT FRONT |
| Парткод: | 302R403620 |
| Деталь: | HOLDER SENSOR |
| Парткод: | 302R403520 |
| Деталь: | SPACER LED |
| Парткод: | 302K312400 |
| Деталь: | LEVER ID SENSOR |
| Парткод: | 302R403590 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 302R403700 |
| Деталь: | ACTUATOR SWITCH |
| Парткод: | 302R403710 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | LABEL BLACK |
| Парткод: | 302K034090 |
| Деталь: | LABEL MAGENTA |
| Парткод: | 302K034100 |
| Деталь: | LABEL CYAN |
| Парткод: | 302K034110 |
| Деталь: | LABEL YELLOW |
| Парткод: | 302K034120 |
| Деталь: | FILM INNER COVER |
| Парткод: | 302R403650 |
| Деталь: | ARM SPRING A |
| Парткод: | 3V2NM18890 |
| Деталь: | SPRING-COMPRESSION ARM B |
| Парткод: | 3V2NM18970 |
| Деталь: | GUIDE LOOP |
| Парткод: | 3V2NM18120 |
| Деталь: | ARM SPRING B |
| Парткод: | 3V2NM18940 |
| Деталь: | SPRING-COMPRESSION ARM A |
| Парткод: | 3V2NM18960 |
| Деталь: | FRICTION PLATE LF |
| Парткод: | 3HK07240 |
| Деталь: | LABEL LOOP |
| Парткод: | 3V2NM18980 |
| Деталь: | GUIDE PF |
| Парткод: | 303R307020 |
| Деталь: | ACTUATOR ORIGINAL |
| Парткод: | 3V2NM18750 |
| Деталь: | ACTUATOR PF |
| Парткод: | 3V2NM18790 |
| Деталь: | SPRING-TORSION PF |
| Парткод: | 3V2NM18620 |
| Деталь: | HOOK PAPER FEED R |
| Парткод: | 3V2NM18170 |
| Деталь: | SPRING HOOK |
| Парткод: | 3V2NM18760 |
| Деталь: | HOOK PAPER FEED F |
| Парткод: | 3V2NM18160 |
| Деталь: | COVER PF |
| Парткод: | 303R307010 |
| Деталь: | CUSHION PF |
| Парткод: | 3V2NM18180 |
| Деталь: | FRICTION PLATE STOPPER PAPER |
| Парткод: | 3V2NM18580 |
| Деталь: | ACTUATOR BASE |
| Парткод: | 303K502200 |
| Деталь: | GUIDE WIRE A |
| Парткод: | 3V2NM18070 |
| Деталь: | COVER DRIVE |
| Парткод: | 3V2NM18320 |
| Деталь: | GEAR Z51S |
| Парткод: | 3V2NM18330 |
| Деталь: | GEAR Z50S |
| Парткод: | 3V2NM18340 |
| Деталь: | GEAR Z54S-Z33S |
| Парткод: | 3V2NM18350 |
| Деталь: | GEAR Z54S-Z33S B |
| Парткод: | 3V2NM18500 |
| Деталь: | LEVER LOOPA |
| Парткод: | 3V2NM18870 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | PLATE EARTH MOTOR |
| Парткод: | 303LJ02100 |
| Деталь: | SHAFT CAM |
| Парткод: | 303R324120 |
| Деталь: | GEAR Z32S PI |
| Парткод: | 3V2NM18950 |
| Деталь: | CAM LOOP |
| Парткод: | 3V2NM18830 |
| Деталь: | MOUNT DRIVE B |
| Парткод: | 3V2NM18310 |
| Деталь: | PARTS MOTOR ROTARY SP |
| Парткод: | 302KY94140 |
| Деталь: | GEAR Z35S |
| Парткод: | 3V2NM18390 |
| Деталь: | GEAR Z51S-Z17S |
| Парткод: | 3V2NM18380 |
| Деталь: | GUIDE WIRE B |
| Парткод: | 3V2NM18080 |
| Деталь: | PARTS DRIVE ASSY A SP |
| Парткод: | 302NM94231 |
| Деталь: | PARTS BRACKET HV LEFT ASSY SP |
| Парткод: | 302R494160 |
| Деталь: | LID WIRE GUIDE |
| Парткод: | 302H039270 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SHEET LSU |
| Парткод: | 302R402300 |
| Деталь: | TR-5205 |
| Парткод: | 302V593050 |
| Деталь: | SPACER POSITIONING DRUM |
| Парткод: | 302R402700 |
| Деталь: | SPRING HOOK RAIL TRANSFER F |
| Парткод: | 302 R402680 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SEAL FAN MOTOR B |
| Парткод: | 302R403640 |
| Деталь: | SEAL FAN MOTOR C |
| Парткод: | 302R403670 |
| Деталь: | FRAME MIDDLE |
| Парткод: | 302R402040 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | HOLDER PAPER LIMIT SENSOR |
| Парткод: | 302R406210 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | DUCT DLP FRONT |
| Парткод: | 302R433040 |
| Деталь: | STOPPER DRUM |
| Парткод: | 302 R402670 |
| Деталь: | SPRING DRUM STOPPER |
| Парткод: | 302R402690 |
| Деталь: | SPONGE DLP FRONT |
| Парткод: | 302R433060 |
| Деталь: | RAIL DRUM BK |
| Парткод: | 302R402570 |
| Деталь: | RAIL DRUM R |
| Парткод: | 302R402580 |
| Деталь: | RAIL DRUM L |
| Парткод: | 302R402590 |
| Деталь: | RAIL DRUM Y |
| Парткод: | 302R402600 |
| Деталь: | GEAR Z15L |
| Парткод: | 302R403310 |
| Деталь: | GUIDE CONTAINER A |
| Парткод: | 302R402550 |
| Деталь: | HOLDER SHUTTER |
| Парткод: | 302R415100 |
| Деталь: | HOOK SHUTTER CONT B |
| Парткод: | 302K002A90 |
| Деталь: | SPRING HOOK SHUTTER |
| Парткод: | 302K002B80 |
| Деталь: | SHUTTER PIPE UP |
| Парткод: | 302R415080 |
| Деталь: | SEAL SHUTTER SUPPLY |
| Парткод: | 302R415240 |
| Деталь: | SPRING SHUTTER SUPPLY A |
| Парткод: | 302K015320 |
| Деталь: | SEAL LID D DLP |
| Парткод: | 302FZ14810 |
| Деталь: | RAIL CONTAINER L |
| Парткод: | 302R402531 |
| Деталь: | DAMPER CONTAINER |
| Парткод: | 302R402760 |
| Деталь: | SPRING DAMPER CONT |
| Парткод: | 302K002B70 |
| Деталь: | RAIL OUTER CASSETTE RIGHT ASSY |
| Парткод: | 302R409320 |
| Деталь: | RAIL OUTER CASSETTE LEFT ASSY |
| Парткод: | 302R409330 |
| Деталь: | RAIL CONTAINER C |
| Парткод: | 302R402540 |
| Деталь: | RAIL CONTAINER R |
| Парткод: | 302R402520 |
| Деталь: | MOUNT INTERLOCK SW |
| Парткод: | 302R402740 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | SHEET HARNESS |
| Парткод: | 302R403720 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390009++H01 |
| Деталь: | TABLE MAIN |
| Парткод: | 3V2R418010 |
| Деталь: | CURSOR FRONT |
| Парткод: | 3V2NM18460 |
| Деталь: | CURSOR REAR |
| Парткод: | 3V2NM18470 |
| Деталь: | COVER CURSOR |
| Парткод: | 3V2R418020 |
| Деталь: | GEAR CASSETTE /A-49 CASSETTE A4 |
| Парткод: | 5MVG127DN071 |
| Деталь: | LABEL FACE UP |
| Парткод: | 303R334020 |
| Деталь: | PARTS TABLE MAIN ASSY SP |
| Парткод: | 302R494110 |
| Деталь: | LK-5195 |
| Парткод: | 302R493151 |
| Деталь: | PARTS UNIT LOW VOLTAGE 100 SP |
| Парткод: | 302SZ94100 |
| Деталь: | PARTS UNIT LOW VOLTAGE 200 SP |
| Парткод: | 302SZ94110 |
| Деталь: | SHEET LVU L |
| Парткод: | 302R439190 |
| Деталь: | MOUNT MAIN LOW |
| Парткод: | 302WL39010 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302WL94010 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302WL94020 |
| Деталь: | PARTS PWB ENGINE ASSY SP |
| Парткод: | 302WL94030 |
| Деталь: | LID WIRE GUIDE |
| Парткод: | 302H039270 |
| Деталь: | PLATE MAIN LOW |
| Парткод: | 302R439030 |
| Деталь: | MOUNT SPRING HV |
| Парткод: | 302R439550 |
| Деталь: | SPRING HV SLEEVE R |
| Парткод: | 302R439590 |
| Деталь: | SPRING HV MAG R |
| Парткод: | 302R439600 |
| Деталь: | SPRING HV MAIN R |
| Парткод: | 302R439610 |
| Деталь: | SPRING TRANS 2T |
| Парткод: | 302R439480 |
| Деталь: | SPRING TCL |
| Парткод: | 302R439680 |
| Деталь: | SPRING MID TRANS |
| Парткод: | 302R439580 |
| Деталь: | LID SPRING HV |
| Парткод: | 302R439670 |
| Деталь: | SPRING HV SLEEVE R4 |
| Парткод: | 302R439620 |
| Деталь: | SPRING HV MAG R4 |
| Парткод: | 302R439630 |
| Деталь: | SPRING HV MAIN R4 |
| Парткод: | 302R439640 |
| Деталь: | BRACKET HVU 2 |
| Парткод: | 302R439470 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302LC94380 |
| Деталь: | SPRING HV PT PB |
| Парткод: | 302R439500 |
| Деталь: | SPRING HV PT CLN |
| Парткод: | 302R439490 |
| Деталь: | SPRING HV BK 1T |
| Парткод: | 302R439510 |
| Деталь: | SPRING HV M 1T |
| Парткод: | 302R439520 |
| Деталь: | SPRING HV C 1T |
| Парткод: | 302R439530 |
| Деталь: | SPRING HV Y 1T |
| Парткод: | 302R439540 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390011++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM590001++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610004++H01 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390003++H01 |
| Деталь: | PARTS MEMORY MODULE SP |
| Парткод: | 302WL94070 |
| Деталь: | SHEET HVU |
| Парткод: | 302R439090 |
| Деталь: | NUT FUSER A /FS-1800 /3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | PLATE MOUNT HV H |
| Парткод: | 302R639020 |
| Деталь: | FAN COOLING 40-15 |
| Парткод: | 302H044120 |
| Деталь: | DUCT CLUTCH A |
| Парткод: | 302R433140 |
| Деталь: | DUCT CLUTCH B |
| Парткод: | 302R433150 |
| Деталь: | SHEET HVU |
| Парткод: | 302R439090 |
| Деталь: | PLATE PWB HVU |
| Парткод: | 302R439200 |
| Деталь: | PARTS UNIT HIGH VOLTAGE MAIN SP |
| Парткод: | 302R594040 |
| Деталь: | SEAL FRAME LONG |
| Парткод: | 302LZ02070 |
| Деталь: | PARTS ROLLER FEED MIDDLE SP |
| Парткод: | 302R494370 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | GEAR Z21L |
| Парткод: | 302K923110 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | BUSH 4-7 |
| Парткод: | 302LC03230 |
| Деталь: | SHAFT DRIVE BOTTLE |
| Парткод: | 302 R403600 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | GEAR Z25S |
| Парткод: | 303MA16120 |
| Деталь: | HOLDER REGIST SENSOR |
| Парткод: | 302R424070 |
| Деталь: | SPRING SENSOR REG EARTH |
| Парткод: | 302R424150 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 303NW94040 |
| Деталь: | GUIDE WIRE ENGINE |
| Парткод: | 302R439110 |
| Деталь: | PARTS ID SENSOR ASSY SP |
| Парткод: | 302R694060 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SHUTTER CLEANER ID |
| Парткод: | 302R402630 |
| Деталь: | FELT CLEANER ID |
| Парткод: | 302HN02970 |
| Деталь: | SPRING SHUTTER ID |
| Парткод: | 302NR02830 |
| Деталь: | PIN LSU |
| Парткод: | 302R402710 |
| Деталь: | SPRING PIN LSU |
| Парткод: | 302R402790 |
| Деталь: | PARTS SPEAKER SP |
| Парткод: | 302LC94370 |
| Деталь: | PARTS PWB SWITCH ASSY SP |
| Парткод: | 302NG94300 |
| Деталь: | SPRING FUSER |
| Парткод: | 302F931270 |
| Деталь: | HOLDER MAIN KEY |
| Парткод: | 302NG04210 |
| Деталь: | KEY POWER |
| Парткод: | 302R404280 |
| Деталь: | NUT FUSER |
| Парткод: | 302K926050 |
| Деталь: | SPRING FUSER EARTH |
| Парткод: | 302R402780 |
| Деталь: | PLATE EARTH EXIT |
| Парткод: | 302R402620 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | PLATE EARTH FUSER |
| Парткод: | 302R431460 |
| Деталь: | CORE 8-16X10 |
| Парткод: | 3HK27050 |
| Деталь: | PARTS MOTOR-PM FUSER SP |
| Парткод: | 302SZ94080 |
| Деталь: | SPRING FUSER DRIVE |
| Парткод: | 302NR31800 |
| Деталь: | GEAR Z44R-Z16S |
| Парткод: | 302NR31250 |
| Деталь: | GEAR Z26S |
| Парткод: | 302NR31260 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | BUSH DU |
| Парткод: | 302F929140 |
| Деталь: | FAN COOLING 40-15 |
| Парткод: | 302H044120 |
| Деталь: | GEAR Z34 CONT D |
| Парткод: | 302H731780 |
| Деталь: | PULLEY PA |
| Парткод: | 302HN24400 |
| Деталь: | PARTS SOLENOID FEED SHIFT SP |
| Парткод: | 302K994380 |
| Деталь: | PARTS MOTOR EJECT SP |
| Парткод: | 302P794060 |
| Деталь: | HOUSING EXIT |
| Парткод: | 302R428020 |
| Деталь: | GUIDE CHANGE |
| Парткод: | 302R428050 |
| Деталь: | PULLEY EXIT REVERSE |
| Парткод: | 302R428080 |
| Деталь: | PLATE EXIT |
| Парткод: | 302R428090 |
| Деталь: | PARTS ROLLER EXIT JS SP |
| Парткод: | 302R494340 |
| Деталь: | PARTS ROLLER EXIT JS2 SP |
| Парткод: | 302R494350 |
| Деталь: | SHAFT EXIT DU |
| Парткод: | 302R428120 |
| Деталь: | PARTS ROLLER EXIT FD SP |
| Парткод: | 302R494360 |
| Деталь: | GEAR Z28S |
| Парткод: | 302R428140 |
| Деталь: | GEAR EXIT Z28S OW |
| Парткод: | 302R428150 |
| Деталь: | GEAR Z40R-Z25S |
| Парткод: | 302R428160 |
| Деталь: | BUSH EXIT 4 |
| Парткод: | 302R428170 |
| Деталь: | GUIDE EXIT RIGHT |
| Парткод: | 302R428190 |
| Деталь: | SPRING GUIDE RIGHT F |
| Парткод: | 302R428200 |
| Деталь: | SPRING GUIDE RIGHT R |
| Парткод: | 302R428210 |
| Деталь: | ACTUATOR EXIT C |
| Парткод: | 302R428220 |
| Деталь: | COVER FRONT |
| Парткод: | 302R428230 |
| Деталь: | COVER MOTOR |
| Парткод: | 302R428240 |
| Деталь: | SPRING EXIT EARTH A |
| Парткод: | 302R428250 |
| Деталь: | SPRING EXIT EARTH B |
| Парткод: | 302R428260 |
| Деталь: | SPRING EXIT |
| Парткод: | 302R428290 |
| Деталь: | CUSHION EXIT GUIDE |
| Парткод: | 302R428300 |
| Деталь: | SPRING CHANGE GUIDE |
| Парткод: | 302R428320 |
| Деталь: | PULLEY EXIT REVERSE |
| Парткод: | 302R428330 |
| Деталь: | LABEL EXIT |
| Парткод: | 302R434130 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | PARTS EXIT ASSY SP |
| Парткод: | 302R494050 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | STOPPER EARTH MIDDLE |
| Парткод: | 302FZ22760 |
| Деталь: | PULLEY PA |
| Парткод: | 302HN24400 |
| Деталь: | GUIDE EXIT PUSH |
| Парткод: | 302K328090 |
| Деталь: | SPRING GUIDE EXIT PUSH |
| Парткод: | 302K328260 |
| Деталь: | GUIDE EXIT |
| Парткод: | 302R428030 |
| Деталь: | COVER GUIDE EXIT |
| Парткод: | 302R428040 |
| Деталь: | ACTUATOR EXIT A |
| Парткод: | 302R428060 |
| Деталь: | ACTUATOR EXIT B |
| Парткод: | 302R428070 |
| Деталь: | PULLEY EXIT REVERSE |
| Парткод: | 302R428080 |
| Деталь: | SHAFT EXIT DU |
| Парткод: | 302R428120 |
| Деталь: | GUIDE EXIT UPPER |
| Парткод: | 302R428180 |
| Деталь: | STATIC ELIMINATOR |
| Парткод: | 302R428270 |
| Деталь: | ACTUATOR EXIT D |
| Парткод: | 302R428280 |
| Деталь: | SPRING EXIT |
| Парткод: | 302R428290 |
| Деталь: | CUSHION ACTUATOR |
| Парткод: | 302R428310 |
| Деталь: | ACTUATOR EXIT E |
| Парткод: | 302R428340 |
| Деталь: | RING STOPPER 4 |
| Парткод: | 5MVL177DN001 |
| Деталь: | CUSHION EXIT PUSH |
| Парткод: | 302R428350 |
| Деталь: | PARTS EXIT ASSY SP |
| Парткод: | 302R494050 |
| Деталь: | HOLDER RELEASE TC |
| Парткод: | 302R431810 |
| Деталь: | BUSH DRIVE |
| Парткод: | 302HN31590 |
| Деталь: | GEAR Z12L RELEASE TC |
| Парткод: | 302R431850 |
| Деталь: | GEAR Z47S |
| Парткод: | 302R431830 |
| Деталь: | WORM-WHEEL RELEASE DRIVE Z40L-Z21S |
| Парткод: | 302K021480 |
| Деталь: | PARTS MOTOR DC ASSY SP |
| Парткод: | 302 R494190 |
| Деталь: | PLATE RELEASE TC |
| Парткод: | 302R431820 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 302KK04570 |
| Деталь: | CASE FAN MOTOR |
| Парткод: | 302R603030 |
| Деталь: | FAN LSU 60-25 |
| Парткод: | 302GR44080 |
| Цена: | 2 800 ₽ |
| Деталь: | PARTS PIPE TR CLN ASSY SP |
| Парткод: | 302R494150 |
| Деталь: | COVER FAN MOTOR |
| Парткод: | 302R603170 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302LC25780 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | PARTS PWB RFID ASSY SP |
| Парткод: | 302 R694110 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000007+H01 |
| Деталь: | DUCT EXIT FAN |
| Парткод: | 302R433070 |
| Деталь: | PARTS PWB KUIO ASSY SP |
| Парткод: | 302K994270 |
| Деталь: | RAIL KUIO |
| Парткод: | 302R439070 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | ACCESS.BAND |
| Парткод: | 7YZM410002++H01 |
| Деталь: | MOUNT USB |
| Парткод: | 302R405210 |
| Деталь: | SPRING USB HOLD |
| Парткод: | 302K905900 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | PLATE EARTH SHIELD |
| Парткод: | 302V539130 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | LEVER FEED ROLLER |
| Парткод: | 3V2NM18131 |
| Деталь: | HOLDER PICKUP B |
| Парткод: | 3V2NM18190 |
| Деталь: | GEAR PICKUP 18 |
| Парткод: | 3V2NM18610 |
| Деталь: | GEAR Z13S |
| Парткод: | 3V2NM18632 |
| Деталь: | SHAFT PICKUP |
| Парткод: | 303R324100 |
| Деталь: | STOPPER PAPER |
| Парткод: | 3V2NM18650 |
| Деталь: | PARTS PULLEY PICKUP ASSY SP |
| Парткод: | 302R494420 |
| Деталь: | SHAFT ROLLER PF |
| Парткод: | 303R324110 |
| Деталь: | GEAR Z18S FEED ROLLER |
| Парткод: | 3V2NM18710 |
| Деталь: | SPRING-TORSION LF |
| Парткод: | 3V2NM18780 |
| Деталь: | PULLEY PF |
| Парткод: | 3V2NM18800 |
| Деталь: | BUSH 4 |
| Парткод: | 302K306460 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | COLLAR PF |
| Парткод: | 3HK07270 |
| Деталь: | COLLAR S SPRING |
| Парткод: | 3V2NM07080 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARALLEL PIN 2.0X10 |
| Парткод: | 7BP512010B0CH01 |
| Деталь: | PARTS PULLEY PAPER FEED ASSY SP |
| Парткод: | 302R494430 |
| Деталь: | PAD SEPARATION |
| Парткод: | 302LW07100 |
| Деталь: | CUSHION PAD |
| Парткод: | 302LW07120 |
| Деталь: | PAD FRONT SEP |
| Парткод: | 303K507102 |
| Деталь: | MOUNT PAD |
| Парткод: | 303LJ07030 |
| Деталь: | FILM FRONT SEP |
| Парткод: | 303LJ07090 |
| Деталь: | SPRING PAD |
| Парткод: | 303LJ24140 |
| Деталь: | CUSHION MOUNT PAD |
| Парткод: | 3V2NM18560 |
| Деталь: | HOLDER PAD |
| Парткод: | 3V2NM18660 |
| Деталь: | GUIDE READING |
| Парткод: | 3V2NM18520 |
| Деталь: | SPRING READING |
| Парткод: | 303LJ02070 |
| Деталь: | PARTS READING UPPER ASSY SP |
| Парткод: | 303R394100 |
| Деталь: | GUIDE LOWER RIGHT |
| Парткод: | 303R324080 |
| Деталь: | SPRING-COMPRESSION CONVEYING |
| Парткод: | 3V2NM18550 |
| Деталь: | SHAFT CONVEYING |
| Парткод: | 303LJ24110 |
| Деталь: | PULLEY CONVEYING |
| Парткод: | 3V2NM18240 |
| Деталь: | GUIDE LOWER LEFT |
| Парткод: | 3V2NM18530 |
| Деталь: | SPRING-COMPRESSION REGIST A |
| Парткод: | 3V2NM18280 |
| Деталь: | SPRING-COMPRESSION REGIST B |
| Парткод: | 3V2NM18290 |
| Деталь: | SHAFT CONVEYING |
| Парткод: | 303R324090 |
| Деталь: | LEVER REGIST |
| Парткод: | 303R324020 |
| Деталь: | PARTS HOLDER PICKUP ASSY SP |
| Парткод: | 303R394020 |
| Деталь: | PARTS HOLDER PAD ASSY SP |
| Парткод: | 303R394030 |
| Деталь: | MOUNT INTERLOCK SW B |
| Парткод: | 302R402770 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | HOLDER DRAWER |
| Парткод: | 302R402260 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | PLATE EARTH DF |
| Парткод: | 302R402290 |
| Деталь: | HOLDER WIRE A |
| Парткод: | 303LL02180 |
| Деталь: | MOUNT HEATER PWB |
| Парткод: | 302R439160 |
| Деталь: | SPRING TRANS FAN |
| Парткод: | 302R439660 |
| Деталь: | PARTS PWB HEATER RELAY ASSY SP |
| Парткод: | 302R694050 |
| Деталь: | PLATE MAIN LEFT |
| Парткод: | 302R439020 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | DUCT FUSER MOTORA |
| Парткод: | 302R433160 |
| Деталь: | DUCT FUSER MOTOR B |
| Парткод: | 302R433170 |
| Деталь: | MOUNT ENGINE |
| Парткод: | 302R439080 |
| Деталь: | SHIELD SCREW |
| Парткод: | 302K903620 |
| Деталь: | PAD SEPARATION |
| Парткод: | 302R408250 |
| Деталь: | SEAL SEPARATION |
| Парткод: | 302R408210 |
| Деталь: | HOLDER SEPARATION |
| Парткод: | 302K308041 |
| Деталь: | SPRING SEPARATION |
| Парткод: | 302R408240 |
| Деталь: | CUSHION HOLDER F |
| Парткод: | 302K308300 |
| Деталь: | CUSHION HOLDER R |
| Парткод: | 302K308310 |
| Деталь: | MOUNT SEPARATION |
| Парткод: | 302MV08040 |
| Деталь: | ROLLER MPF |
| Парткод: | 302K308150 |
| Деталь: | SPRING MPF ROLL |
| Парткод: | 302K308270 |
| Деталь: | PIN FEED ROLL |
| Парткод: | 302MV08020 |
| Деталь: | PULLEY MPF |
| Парткод: | 302MV08030 |
| Деталь: | BASE MPF |
| Парткод: | 302R408010 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | ACTUATOR MPF |
| Парткод: | 302K308020 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | 302K308250 |
| Деталь: | SPRING LIFT F |
| Парткод: | 302K308130 |
| Деталь: | SPRING LIFT R |
| Парткод: | 302K308120 |
| Деталь: | PLATE LIFT |
| Парткод: | 302R408040 |
| Деталь: | PAD LIFT |
| Парткод: | 302K308111 |
| Деталь: | ARM LIFT |
| Парткод: | 302K308140 |
| Деталь: | SPRING EARTH |
| Парткод: | 302R408130 |
| Деталь: | GUIDE UPPER MPF |
| Парткод: | 302R408020 |
| Деталь: | STAY MPF UPPER |
| Парткод: | 302R408030 |
| Деталь: | BUSH 10 |
| Парткод: | 302K308070 |
| Деталь: | SHAFT MPF |
| Парткод: | 302R408050 |
| Деталь: | PARTS GEAR MPF Z28 SP |
| Парткод: | 302K394320 |
| Деталь: | PARTS HOLDER SEPARATION SP |
| Парткод: | 302R494180 |
| Деталь: | PARTS ROLLER MPF ASSY SP |
| Парткод: | 302MV94021 |
| Деталь: | GEAR Z36L-Z20S |
| Парткод: | 302HN31030 |
| Деталь: | PARTS DC MOTOR ASSY C SP |
| Парткод: | 302R494290 |
| Деталь: | HOUSING DRIVE |
| Парткод: | 302R409500 |
| Деталь: | LID HOUSING DRIVE |
| Парткод: | 302R409510 |
| Деталь: | GEAR Z57S |
| Парткод: | 302R409520 |
| Деталь: | JOINT LIFT |
| Парткод: | 302R409530 |
| Деталь: | GEAR Z34S-Z16S |
| Парткод: | 302R409540 |
| Деталь: | SPRING JOINT LIFT |
| Парткод: | 302R409550 |
| Деталь: | GEAR Z41S Z14S |
| Парткод: | 303K831280 |
| Деталь: | HOLDER PAPER SENSOR |
| Парткод: | 302 R409360 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000007+H01 |
| Деталь: | PARTS PWB THERMISTOR ASSY SP |
| Парткод: | 302R694190 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302LC94380 |
| Деталь: | DUCT BASE REAR |
| Парткод: | 302R433120 |
| Деталь: | DUCT BASE FRONT |
| Парткод: | 302R433130 |
| Деталь: | HOLDER PWB |
| Парткод: | 302R439170 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610004++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510018++H01 |
| Деталь: | DUCT DLP REAR A |
| Парткод: | 302R433010 |
| Деталь: | DUCT DLP REAR B |
| Парткод: | 302R433020 |
| Деталь: | GUIDE WIRE INLET |
| Парткод: | 302R439120 |
| Деталь: | LID WIRE GUIDE |
| Парткод: | 302H039270 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | MOUNT INLET A |
| Парткод: | 302R439050 |
| Деталь: | GUIDE WIRE LVU |
| Парткод: | 302R439130 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | CAP DECK PIN |
| Парткод: | 302R439140 |
| Деталь: | SEAL CASE D DLP |
| Парткод: | 302FZ14970 |
| Деталь: | SHIELD SCREW |
| Парткод: | 302H002380 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390005++H01 |
| Деталь: | PARTS LIFT MOTOR ASSY SP |
| Парткод: | 302R494220 |
| Деталь: | PARTS PAPER SENSOR ASSY SP |
| Парткод: | 302R494130 |
| Деталь: | SLIDER ISU |
| Парткод: | 302H917450 |
| Деталь: | STOPPER BUSH ISU |
| Парткод: | 302KW17150 |
| Деталь: | BUSH ISU |
| Парткод: | 302NM17150 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | PIN COVER |
| Парткод: | 303MH04040 |
| Деталь: | PIN DLP RAIL |
| Парткод: | 302GR02852 |
| Деталь: | PARTS ISU TOP SP |
| Парткод: | 302R694010 |
| Деталь: | SPRING EARTH ISU B |
| Парткод: | 302R417220 |
| Деталь: | MOUNT TENSION PULLEY |
| Парткод: | 3V2NM17210 |
| Деталь: | PULLEY TENSION |
| Парткод: | 302M417180 |
| Деталь: | SPRING-COMPRESSION ISU BELT |
| Парткод: | 3V2NM17600 |
| Деталь: | SPRING EARTH ISU A |
| Парткод: | 302R417050 |
| Деталь: | PARTS MOTOR ISU SP |
| Парткод: | 302LW94060 |
| Деталь: | GEAR Z63R-P32 ISU |
| Парткод: | 3V2NM17200 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | BUSHING FAN |
| Парткод: | 302JD19140 |
| Деталь: | PIN LSU |
| Парткод: | 302JD19150 |
| Деталь: | SHEET FFCB |
| Парткод: | 302R417110 |
| Деталь: | TAPE FFC BD |
| Парткод: | 302NR19260 |
| Деталь: | BELT ISU |
| Парткод: | 302R417040 |
| Деталь: | SHAFT ISU |
| Парткод: | 302R417030 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBFZZ65C002H01 |
| Деталь: | SHEETFFCA |
| Парткод: | 302R417090 |
| Деталь: | LABEL CAUTION |
| Парткод: | 302R434110 |
| Деталь: | COVER ISU BOTTOM |
| Парткод: | 302V517020 |
| Деталь: | CONN.CORD ASSY FPC WIFI |
| Парткод: | 302ND46732 |
| Деталь: | ISU ASSY L SP |
| Парткод: | 302R493140 |
| Деталь: | PARTS WIFI UNIT SP |
| Парткод: | 303RR94010 |
| Деталь: | MC-5195 |
| Парткод: | 302R493060 |
| Деталь: | DV-5195K |
| Парткод: | 302R493072 |
| Деталь: | DV-5195M |
| Парткод: | 302R493082 |
| Деталь: | DV-5195C |
| Парткод: | 302R493092 |
| Деталь: | DV-5195Y |
| Парткод: | 302R493102 |
| Деталь: | DK-5195 |
| Парткод: | 302R493053 |
| Деталь: | BASE DP |
| Парткод: | 303R302010 |
| Деталь: | STOPPER BASE |
| Парткод: | 303R402020 |
| Деталь: | SPRING-COMPRESSION EXIT |
| Парткод: | 3V2NM18990 |
| Деталь: | SHAFT EJECT PULLEY |
| Парткод: | 302F928290 |
| Деталь: | PULLEY EJECT |
| Парткод: | 3HK10030 |
| Деталь: | SPONGE EJECT |
| Парткод: | 3HK10060 |
| Деталь: | SPONGE ORIGINAL MAT FILM |
| Парткод: | 303PH02030 |
| Деталь: | CUSHION ORIGINAL MAT B |
| Парткод: | 303MX02032 |
| Деталь: | Hinge Left |
| Парткод: | 303R302021 |
| Деталь: | Hinge Right |
| Парткод: | 303R302031 |
| Деталь: | PLATE HINGE |
| Парткод: | 303R302050 |
| Деталь: | FK-5347 |
| Парткод: | 302WL93020 |
| Деталь: | FK-5345 |
| Парткод: | 302WL93010 |
| Деталь: | COVER WIRE FUSER |
| Парткод: | 302R402750 |
| Деталь: | COVER FRONT |
| Парткод: | 303R304010 |
| Деталь: | COVER FRONT B |
| Парткод: | 303R304040 |
| Деталь: | COVER REARA |
| Парткод: | 303R304020 |
| Деталь: | COVER REAR B |
| Парткод: | 303R304030 |
| Деталь: | ARM PF COVER |
| Парткод: | 303R302040 |
| Деталь: | STOPPER 4 |
| Парткод: | 302FZ25740 |
| Деталь: | LABEL SIZE DIRECTION |
| Парткод: | 303R334010 |
| Деталь: | PLATE ORIGINAL |
| Парткод: | 302H918021 |
| Деталь: | CUSHION ORIGINAL MAT A |
| Парткод: | 303MX02022 |
| Деталь: | PARTS MOTOR-BL ASSY D SP |
| Парткод: | 302 R494461 |
| Деталь: | PARTS MOTOR-BL ASSY B SP |
| Парткод: | 302R494441 |
| Деталь: | PLATE DRUM EARTH |
| Парткод: | 302R412150 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | GEAR Z44L-Z33L |
| Парткод: | 302R431430 |
| Деталь: | GEAR Z63R-Z24R |
| Парткод: | 302NR31240 |
| Деталь: | GEAR Z35R |
| Парткод: | 302R431420 |
| Деталь: | HOLDER CONT DRIVE R |
| Парткод: | 302R431620 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | SPRING JOINT |
| Парткод: | 302NR02290 |
| Деталь: | GEAR JOINT Z38S |
| Парткод: | 302R431640 |
| Деталь: | GEAR Z50S |
| Парткод: | 302R431660 |
| Деталь: | GEAR Z25S-Z50L |
| Парткод: | 302R431650 |
| Деталь: | PARTS DC MOTOR ASSY B SP |
| Парткод: | 302 R494200 |
| Деталь: | PLATE MOTOR DC |
| Парткод: | 302R431630 |
| Деталь: | HOLDER CONT DRIVE F |
| Парткод: | 302R431610 |
| Деталь: | DR-5195 |
| Парткод: | 302R493041 |
| Деталь: | PARTS MOTOR-BL ASSY E SP |
| Парткод: | 302 R494471 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SPRING TC L |
| Парткод: | 302HG24150 |
| Деталь: | BUSH REG R |
| Парткод: | 302HN24110 |
| Деталь: | STOPPER BUSH REG |
| Парткод: | 302HN24150 |
| Деталь: | SPRING SEP EARTH A |
| Парткод: | 302HN24270 |
| Деталь: | SPRING DU |
| Парткод: | 302HN24290 |
| Деталь: | STOPPER TC SPRING |
| Парткод: | 302NT22010 |
| Деталь: | PULLEY PA |
| Парткод: | 302HN24400 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 302KK04570 |
| Деталь: | SHEET REGIST C |
| Парткод: | 302KV06260 |
| Деталь: | SHEET REGIST CR |
| Парткод: | 302KV06410 |
| Деталь: | GEAR Z31R |
| Парткод: | 302KV24110 |
| Деталь: | PARTS ROLLER REGIST RUBBER SP |
| Парткод: | 302R494400 |
| Деталь: | SPRING EARTH REGIST RUBBER |
| Парткод: | 302NR24110 |
| Деталь: | BUSH REGIST EW |
| Парткод: | 302NR24120 |
| Деталь: | SPRING REGIST L |
| Парткод: | 302NR24140 |
| Деталь: | SPRING REGIST R |
| Парткод: | 302NR24150 |
| Деталь: | SPRING BRUSH EARTH |
| Парткод: | 302R422040 |
| Деталь: | SPRING PAPER CHUTE |
| Парткод: | 302R422080 |
| Деталь: | GUIDE FEED DU |
| Парткод: | 302R424020 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | 302R424030 |
| Деталь: | ACTUATOR DU |
| Парткод: | 302R424040 |
| Деталь: | SPRING DU ACTUATOR |
| Парткод: | 302R424080 |
| Деталь: | SPRING GUIDE EARTH |
| Парткод: | 302R424120 |
| Деталь: | SPRING MIDDLE PULLEY |
| Парткод: | 302R424130 |
| Деталь: | SPRING EARTH CONVEYING |
| Парткод: | 302R424140 |
| Деталь: | LABEL CONVEYING A |
| Парткод: | 302R424160 |
| Деталь: | PLATE GUIDE CONVEYING |
| Парткод: | 302R424210 |
| Деталь: | COVER HARNESS A |
| Парткод: | 302R429100 |
| Деталь: | SHEET DISCHARGER |
| Парткод: | 302R424280 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SHEET PAPER GUIDE EARTH |
| Парткод: | 302NT22030 |
| Деталь: | WIRE CONVEYING UNIT |
| Парткод: | 302R646350 |
| Деталь: | PARTS CONVEYING ASSY SP |
| Парткод: | 302R494061 |
| Деталь: | GEAR Z22L TC ROLL B |
| Парткод: | 302R422090 |
| Деталь: | SPRING SEP EARTH B |
| Парткод: | 302HN22080 |
| Деталь: | TAPE BRUSH |
| Парткод: | 302HN22100 |
| Деталь: | PARTS ROLLER TRANSFER SP |
| Парткод: | 302NR94061 |
| Цена: | 4 400 ₽ |
| Деталь: | BRUSH DISCHARGER |
| Парткод: | 302NR22030 |
| Деталь: | HOLDER BRUSH |
| Парткод: | 302NR22101 |
| Деталь: | BUSH TRANS REAR |
| Парткод: | 302R422010 |
| Деталь: | LEVER TRANS RELEASE F |
| Парткод: | 302R422020 |
| Деталь: | LEVER TRANS RELEASE R |
| Парткод: | 302R422030 |
| Деталь: | GUIDE PAPER CHUTE A |
| Парткод: | 302R422100 |
| Деталь: | SHEET PAPER CHUTE |
| Парткод: | 302R422060 |
| Деталь: | BUSH TRANS F |
| Парткод: | 302R422070 |
| Деталь: | LABEL CONVEYING B |
| Парткод: | 302R424170 |
| Деталь: | LABEL CONVEYING CAUTION |
| Парткод: | 302R434191 |
| Деталь: | HOOK DU RELEASE |
| Парткод: | 302 R429040 |
| Деталь: | COVER RELEASE HOOK |
| Парткод: | 302R429130 |
| Деталь: | SPRING HOOK L |
| Парткод: | 302KV29150 |
| Деталь: | SPRING HOOK R |
| Парткод: | 302KV29160 |
| Деталь: | SPRING EARTH DU A |
| Парткод: | 302R429070 |
| Деталь: | STOPPER MPFFEED |
| Парткод: | 302KV08180 |
| Деталь: | SPRING CONVEYING STOPPER |
| Парткод: | 302R429140 |
| Деталь: | PARTS ROLLER DU L SP |
| Парткод: | 302R494380 |
| Деталь: | PARTS ROLLER DU SP |
| Парткод: | 302R494410 |
| Деталь: | BUSH SPIRAL |
| Парткод: | 302K312341 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | BUSH DU JOINT |
| Парткод: | 302R429120 |
| Деталь: | GEAR Z21L DU |
| Парткод: | 302R429020 |
| Деталь: | SPRING EARTH DU B |
| Парткод: | 302R429080 |
| Деталь: | BUSH ROLLER EARTH |
| Парткод: | 302KV29190 |
| Деталь: | SPRING EARTH DU ROLL |
| Парткод: | 302R429060 |
| Деталь: | PULLEY P24-S2M |
| Парткод: | 302KV29200 |
| Деталь: | PULLEY P24 DU |
| Парткод: | 302NR29040 |
| Деталь: | BELT S2M Z256 |
| Парткод: | 302R429050 |
| Деталь: | COVER HARNESS B |
| Парткод: | 302R429110 |
| Деталь: | COVER BELT DU |
| Парткод: | 302R429150 |
| Деталь: | SHAFT RIGHT COVER F |
| Парткод: | 302K304550 |
| Деталь: | FILM CONVEYING SHAFT |
| Парткод: | 302K304630 |
| Деталь: | SHAFT RIGHT COVER R |
| Парткод: | 302K304560 |
| Деталь: | STRAP RIGHT COVER |
| Парткод: | 302R429090 |
| Деталь: | COVER RIGHT |
| Парткод: | 302R429010 |
| Деталь: | STRAP LINK MPF |
| Парткод: | 302R408230 |
| Деталь: | STOPPER STRAP |
| Парткод: | 302K308470 |
| Деталь: | PARTS 2ND TRANS ASSY SP |
| Парткод: | 302R494070 |
| Деталь: | SPRING FEED |
| Парткод: | 302HN31410 |
| Деталь: | BUSH DRIVE |
| Парткод: | 302HN31590 |
| Деталь: | SPRING INPUT MPF |
| Парткод: | 302HN31650 |
| Цена: | 150 ₽ |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | 302HN31660 |
| Деталь: | SOLENOID MPF |
| Парткод: | 302HN44160 |
| Деталь: | GEAR Z28S |
| Парткод: | 302K331170 |
| Деталь: | GEAR Z45S INPUT MPF A |
| Парткод: | 302K331180 |
| Деталь: | GEAR Z45S INPUT MPF B |
| Парткод: | 302K331190 |
| Деталь: | BUSH DRIVE 8 |
| Парткод: | 302K331230 |
| Деталь: | GEAR Z35R |
| Парткод: | 302K931510 |
| Деталь: | PARTS MOTOR-BL ASSY F SP |
| Парткод: | 302 R494481 |
| Деталь: | BUSH DRIVE POM |
| Парткод: | 302LV31480 |
| Деталь: | GEAR Z72R-Z28L |
| Парткод: | 302NR31020 |
| Деталь: | GEAR Z72R-Z40L |
| Парткод: | 302NR31030 |
| Деталь: | GEAR Z24L |
| Парткод: | 302NR31060 |
| Деталь: | GEAR Z26L |
| Парткод: | 302NR31070 |
| Деталь: | GEAR Z25R OUTPUT CL |
| Парткод: | 302NR31090 |
| Деталь: | GEAR Z32L OUTPUT CL |
| Парткод: | 302NR31100 |
| Деталь: | SHAFT CLUTCH FEED |
| Парткод: | 302NR31110 |
| Деталь: | PIN DRIVE D |
| Парткод: | 302NR31340 |
| Деталь: | SHEET FEED DRIVE A |
| Парткод: | 302NR31680 |
| Деталь: | PARTS CLUTCH 35 Z35R SP |
| Парткод: | 302NR94010 |
| Деталь: | CAM MPF |
| Парткод: | 302R408190 |
| Деталь: | CONNECTOR 292254-2 |
| Парткод: | 7YCC02B1003+H01 |
| Деталь: | HOLDER FEED DRIVE R |
| Парткод: | 302R431210 |
| Деталь: | HOLDER FEED DRIVE F |
| Парткод: | 302R431220 |
| Деталь: | GEAR Z31L |
| Парткод: | 302R431280 |
| Деталь: | GEAR Z48R-Z22S |
| Парткод: | 302R431310 |
| Деталь: | SHAFT CLUTCH DLP |
| Парткод: | 302R431350 |
| Деталь: | GEAR Z25R |
| Парткод: | 302R431320 |
| Деталь: | ONE-WAY CLUTCH 6 |
| Парткод: | 302R424270 |
| Деталь: | GEAR Z24R |
| Парткод: | 302R431330 |
| Деталь: | GEAR Z27R |
| Парткод: | 302R431270 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | SHAFT JOINT REGIST |
| Парткод: | 302R431360 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR Z22R |
| Парткод: | 302R431300 |
| Деталь: | GUIDE FEED DRIVE |
| Парткод: | 302R431230 |
| Деталь: | SHAFT JOINT MID |
| Парткод: | 302R431250 |
| Деталь: | PARTS FEED DRIVE ASSY SP |
| Парткод: | 302R494081 |
| Деталь: | SPRING BYPASS TEBLE |
| Парткод: | 302FB17700 |
| Деталь: | TABLE MPF A |
| Парткод: | 302R408060 |
| Деталь: | TABLE MPF B |
| Парткод: | 302R408070 |
| Деталь: | TABLE MPF D |
| Парткод: | 302R408090 |
| Деталь: | CURSOR MPF FRONT |
| Парткод: | 302R408100 |
| Деталь: | CURSOR MPF REAR |
| Парткод: | 302R408110 |
| Деталь: | STOPPER GEAR |
| Парткод: | 302 R408150 |
| Деталь: | SPRING CURSOR |
| Парткод: | 302R408160 |
| Деталь: | STOPPER MULTI |
| Парткод: | 302 R408170 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 302R408220 |
| Деталь: | LABEL MPF CAUTION |
| Парткод: | 302R434010 |
| Деталь: | GEAR 20,PAPER FEED DRIVE |
| Парткод: | 35322020 |
| Деталь: | TABLE MPF C |
| Парткод: | 302R408080 |
| Деталь: | PARTS MPF TABLE ASSY L SP |
| Парткод: | 302R494090 |
Коды ошибок
C0030
C0070
C0100
C0120
C0130
C0140
C0150
C0160
C0170
C0180
C0350
C0360
C0640
C0800
C0830
C0840
C0870
C0920
C0950
C0970
C1010
C1020
C1030
C1040
C1800
C1810
C1900
C1910
C2101
C2102
C2112
C2201
C2202
C2211
C2500
C2600
C2610
C2700
C2760
C2820
C3100
C3200
C3300
C3500
C3800
C4001
C4011
C4101
C4102
C4103
C4104
C4201
C4600
C4700
C5101
C5102
C5103
C5104
C6000
C6020
C6030
C6040
C6050
C6200
C6220
C6230
C6250
C6400
C6610
C6910
C7001
C7002
C7003
C7004
C7101
C7102
C7103
C7104
C7200
C7210
C7221
C7231
C7401
C7402
C7403
C7404
C7411
C7412
C7413
C7414
C7601
C7602
C7611
C7612
C7613
C7614
C7620
C7800
C7810
C7901
C7902
C7903
C7904
C7911
C7912
C7913
C7914
C8000
C8090
C8100
C8140
C8160
C8170
C8180
C8190
C8200
C8210
C8230
C8260
C8500
C8510
C8520
C8800
C8900
C9180
C9500
C9540
F000
F010
F020
F040
F050
Описание
| Error code: | C0030 |
| Description: | FAX PWB system error |
| Causes: | The FAX processing cannot be continued due to the FAX firmware error. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. |
| Error code: | C0070 |
| Description: | Toner motor |
| Causes: | Abnormal detection of FAX control PWB incompatibility in the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Remedy: | 1 Checking the FAX PWB The incompatible FAX PWB is installed. Install the FAX PWB for the applicable model. 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0100 |
| Description: | Charge corona winding problem |
| Causes: | An abnormal status is output from the flash memory. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. If not repaired, replace the main PWB. |
| Error code: | C0120 |
| Description: | MAC address data error |
| Causes: | The MAC address data is incorrect. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the MAC address The MAC address is incorrect. Replace the main PWB when the MAC address is not indicated on the network status page. |
| Error code: | C0130 |
| Description: | Backup memory read / write error |
| Causes: | The reading or writing into the flash memory is unavailable. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reconnect the connectors on the main PWB. At that time, fix or replace the wires if they are pinched by other parts or have any damage. When the issue is not resolved, replace the main PWB. |
| Error code: | C0140 |
| Description: | Backup memory (EEPROM) data problem • Reading data from EEPROM is abnormal. |
| Causes: | Data damage of EEPROM. |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | C0150 |
| Description: | Engine EEPROM reading / writing error |
| Causes: | 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing data. 2. The data read reading in 2 points mismatches 8 times continuously. 3. The read data and the write data mismatch 8 times continuously. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0160 |
| Description: | Engine PWB EEPROM data error |
| Causes: | The data read from the EEPROM is judged as abnormal. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing U021 The storage data in the EEPROM on the engine PWB is faulty. Execute U021. Executing U021 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. |
| Error code: | C0170 |
| Description: | Charger count error |
| Causes: | The values in one of the billing counters, life counter or the scanner counter mismatch between the main side and the engine side. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. Detaching and reattaching the main PWB 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0180 |
| Description: | Machine serial number mismatch |
| Causes: | The machine serial Nos. in the main PWB and the EEPROM on the engine PWB mismatch when turning the power on. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. Executing U004 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0350 |
| Description: | Panel PWB communication error (Electronic volume I2C communication error) |
| Causes: | Since NACK was received during the I2C communication, the retry was repeated 5 times and the initial command was transmitted, and then the retry was repeated 5 times again. After that, NACK was also received. |
| Remedy: | 1 Resetting the main power The operation of the operation panel main PWB is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Operation panel main PWB - Main PWB • Operation panel main PWB - NFC PWB Wiring diagram 3 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. Detaching and reattaching the operation panel PWB 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 5 Replacing the NFC PWB The NFC PWB is faulty. Replace the NFC PWB. |
| Error code: | C0360 |
| Description: | Engine CPU - Feed ASIC communication error |
| Causes: | The communication with the feed ASIC failed 10 times continuously. |
| Remedy: | 1 Resetting the main power The engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Feed PWB - Engine PWB Wiring diagram 4 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0640 |
| Description: | Hard Disk error |
| Causes: | The HDD cannot be accessed properly. |
| Remedy: | 1 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 2 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 3 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 4 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0800 |
| Description: | Image processing error |
| Causes: | The print sequence jam (J010x) was detected 2 times continuously. |
| Remedy: | 1 Checking the image data The image data is faulty. When this issue occurs only when handling the certain image data, check if the image data is faulty. 2 Checking the situation The printing operation of the certain file is faulty. Acquire the jobs log if the phenomenon can be reproduced by specifying the job when the error was detected.` 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. Detaching and reattaching the main PWB 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0830 |
| Description: | FAX PWB flash program area checksum error |
| Causes: | The program stored in the flash memory on the FAX PWB is broken so it cannot perform. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 2 Checking the FAX PWB The FAX PWB is not properly connected. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0840 |
| Description: | RTC error ("Time for maintenance T" appears) |
| Causes: | [Check at start-up] • RTC values are old. • Power has not been turned on for over 5 years. • RTC value is older than 2000/1/1 00:01. [Periodic check per 5 minutes after start-up] • RTC values are older than the ones at the last check. • Partial operation by power reset after C840 error and "Time for Maintenance T" is indicated. |
| Remedy: | 1 Executing U906 The backup battery on the main PWB is faulty, and so, the RTC settings are erased after unplugging the power cord. Execute U906 to reset the display [Maintenance T]. After that, set the date/time (RTC) in the System menu. (It is necessary to execute this process whenever to unplug/plug the power cord.) Executing U906 2 Replacing the main PWB The main PWB is faulty, or the backup battery runs out. If service call error C0840 frequently appears after performing the previous step, replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0870 |
| Description: | PC FAX Image data transmission error |
| Causes: | Data was not properly transmitted even if the specified times of retry were made when the large volume data is transmitted between the FAX PWB and the main PWB. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 3 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 6 Executing U024 The data stored in the SSD is faulty. Execute U024 [SSD Format]. Executing U024 |
| Error code: | C0920 |
| Description: | 1st drawer lift |
| Causes: | The backup data could not be stored since the file system of the flash memory is faulty. |
| Remedy: | 1 Initializing the fax FAX control values are incorrect Execute U600 to initialize the FAX. Executing U600 2 Checking the FAX PWB The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Reinstalling the FAX PWB The FAX PWB is not properly installed. Reinstall the FAX PWB. FAX Installation Guide 4 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 5 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0950 |
| Description: | 4th drawer lift problem |
| Causes: | Print processing of the received FAX could not be executed and the job continues staying. |
| Remedy: | 1 Resetting the main power The printing process is not properly executed. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is faulty. Upgrade the main firmware to the latest version. Firmware upgrade |
| Error code: | C0970 |
| Description: | Cleaning unit EEPROM error • An error occurs in EEPROM data read or write for the cleaning unit. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective cleaning unit. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC5 on the engine PWB and the cleaning unit, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective cleaning unit. Replace the cleaning unit. |
| Error code: | C1010 |
| Description: | Lift motor 1 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 1 is installed. 2. The lock-up signal is not released for 1s after lift motor 1 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift motor 1 - Feed PWB Wiring diagram 4 Checking lift motor 1 Lift motor 1 is faulty. Check the operation of lift motor 1, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 1 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 1 is not properly attached or faulty. Reattach lift sensor 1. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1020 |
| Description: | Lift motor 2 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 2 is installed. 2. The lock-up signal is not released for 1s after lift motor 2 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Lift motor 2 - Feed PWB Wiring diagram 4 Checking lift motor 2 Lift motor 2 is faulty. Check the operation of lift motor 2, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 2 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 2 is not properly attached or faulty. Reattach lift sensor 2. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1030 |
| Description: | Lift motor 3 error • When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on. This error is detected four times successively. • During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 3. Defective lift motor 3. Poor contact of lift motor 3 connector terminals. Defective lift limit switch 3. Poor contact of lift limit switch 3 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 3. Replace lift motor 3. Defective lift motor 3. Check for continuity across the coil. If none, replace lift motor 3. Poor contact of lift motor 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 3. Run maintenance item U031 and turn lift limit switch 3 on and off manually. Replace lift limit switch 3 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB |
| Error code: | C1040 |
| Description: | Lift motor 4 error • When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on. This error is detected four times successively. • During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 4. Defective lift motor 4. Poor contact of lift motor 4 connector terminals. Defective lift limit switch 4. Poor contact of lift limit switch 4 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 4. Replace lift motor 4. Defective lift motor 4. Check for continuity across the coil. If none, replace lift motor 4. Poor contact of lift motor 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 4. Run maintenance item U031 and turn lift limit switch 4 on and off manually. Replace lift limit switch 4 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB. |
| Error code: | C1800 |
| Description: | Large capacity feeder communication error Condition: When turning the main power off and on while disconnecting the connector of the cable from the side multi feeder, this service call error does not reappear. (It is caused by the large capacity feeder.) |
| Causes: | The communication error was detected 10 times continuously. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the large capacity feeder firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB (Large capacity feeder) - PF main PWB (Side multi feeder) • PF main PWB (Side multi feeder) - Engine PWB Wiring diagram 3 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Large capacity feeder) Detaching and reattaching the PF main PWB (Large capacity feeder) 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1810 |
| Description: | Side Multi Feeder communication error Object: Side multi feeder |
| Causes: | The communication error was detected 10 times continuously. |
| Remedy: | 1 Checking the connection It is not properly connected to the main unit. Reconnect the cable of the side multi feeder to the main unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB - Engine PWB Wiring diagram 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1900 |
| Description: | Large capacity feeder EEPROM error Condition: When outputting Event Log after turning the main power off and on while disconnecting the connector of the cable from the side multi feeder, this service call error is not recorded. (It is caused by the large capacity feeder.) (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously when writing. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the large capacity feeder firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB (Large capacity feeder) - PF main PWB (Side multi feeder) • PF main PWB (Side multi feeder) - Engine PWB Wiring diagram 3 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Large capacity feeder) Detaching and reattaching the PF main PWB (Large capacity feeder) 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1910 |
| Description: | Side Multi Feeder EEPROM error (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously when writing. |
| Remedy: | 1 Checking the connection It is not properly connected to the main unit. Reconnect the cable of the side multi feeder to the main unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB - Engine PWB (Cable from the Side Multi Feeder) Wiring diagram 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2101 |
| Description: | Developer motor error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking the developer motor The developer motor drive is faulty. Execute U030 [DLP(K)] and check the developer motor K operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 5 Checking the developer motor The developer motor is not properly attached or faulty. Reattach the developer motor. If not repaired, replace the motor. Detaching and reattaching the developer motor 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2102 |
| Description: | Developer motor C error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor C drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor C is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking developer motor C The developer motor C drive is faulty. Execute U030 [DLP(C)] and check the developer motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 5 Checking developer motor C Developer motor C is not properly attached or faulty. Reattach developer motor C. If not repaired, replace the motor. Detaching and reattaching the main drive unit 6 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2112 |
| Description: | Developer motor CMY Startup error (DC brushless) |
| Causes: | The steady signal does not turns on for 2s continuously after developer motor C/M/Y started up. |
| Remedy: | 1 Replacing the gear The gear does not rotate properly Replace the developer unit drive gear if it is faulty 2 Replacing the developer unit The developer roller does not rotate properly Check if the developer roller rotates, and replace the developer unit C/M/Y if not rotating 3 Checking the drive parts The drive parts do not operate properly Execute U030 [DLP(CMY)] to check if the developer motor C/M/Y drive gear rotates or has excessive load. Apply grease and repair the parts 4 Checking the connection The connector is not connected properly. Or wires are faulty Re-insert the following connector of the wire If there is no conductivity, replace the wire. Developer motor C/M/Y - Engine PWB 5 Checking developer motor C/ M/Y The developer motor C/M/Y is not installed properly or is faulty Reattach the developer motor C/M/Y If not resolved, replace it 6 Updating the firmware Firmware version is not the latest. Upgrade the firmware to the latest version 7 Checking the Engine PWB The engine PWB is faulty Replace the engine PWB |
| Error code: | C2201 |
| Description: | Drum motor steady-state error |
| Causes: | The ready signal is at the H level for 1s continuously after the drum motor became stable. |
| Remedy: | 1 Checking the drum motor The drum motor drive is faulty. Execute U030 [Process] and check the drum motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 4 Checking the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 5 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2202 |
| Description: | Drum motor C steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB C at every 1s. |
| Remedy: | 1 Checking drum motor C The drum motor C drive is faulty. Execute U030 [Process] and check the drum motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2211 |
| Description: | Drum motor startup error |
| Causes: | The ready signal does not turn on when passing 2s after the drum motor starts up. |
| Remedy: | 1 Checking the drum motor The drum motor operation is faulty. Execute U030 [Process] and check the drum motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the drum unit and the developer unit The drum does not properly rotate. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 4 Replacing the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 5 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C2500 |
| Description: | Feed motor error |
| Causes: | The ready signal is not at the L level after passing 2s since the feed motor drive was started. |
| Remedy: | 1 Checking the feed motor The operation of the feed motor is faulty. Execute U030 [Feed] to check the feed motor operation. Check if the drive gears rotate and have no excessive load, and apply the grease (EM-LP, Part no: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the feed motor The feed motor is faulty. Replace the feed motor. 4 Replacing the feed drive unit The feed drive unit is faulty. Replace feed drive unit. Detaching and reattaching the Feed Drive Unit 5 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 6 Firmware upgrade The firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB 8 Replacing the feed image PWB The power can`t be supplied to the feed drive PWB. Replace the feed image PWB. |
| Error code: | C2600 |
| Description: | PF feed motor error |
| Causes: | The ready signal is not at the L level (stable rotation) after passing 1s since the PF feed motor drive started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected, or it is faulty. Execute U247 [2PF] or [LCF] > [Motor On] to check the paper feed operation. If the PF feed motor does not operate properly, reconnect the connector of the motor. Check if the PF feed roller and the drive gears rotate smoothly and have no excessive load, apply the grease (EM-50LP, Part no.: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF PWB • PF PWB - Engine PWB (Drawer connector between the paper feeder and the main unit) Service Manual - Section 8 `PWBs` 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF Drive Unit 4 Firmware upgrade The engine firmware or the PF firmware is faulty. Upgrade the engine firmware and the PF firmware to the latest version. Firmware Update 5 Replacing the PF PWB The PF PWB is faulty. Replace the PF PWB. Detaching and reattaching the PF PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C2610 |
| Description: | PF feed motor error (Large Capacity Feeder in the main unit) |
| Causes: | The ready signal is not at the L level (stable rotation) for passing 2s since the PF feed motor drive is started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected. The drive parts are faulty. Execute U247 [LCF] > [Motor On] to check the paper feeding operation. If the PF feed motor does not properly operate, reconnect the connector. Check if the PF feed roller and the drive gears rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. Executing U247 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF main PWB • PF main PWB - Engine PWB Wiring diagram 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF drive unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C2700 |
| Description: | Color release motor error |
| Causes: | Turning the color release sensor on and off is not detected for 5s while the color release motor is driving. |
| Remedy: | 1 Checking the drive components The drive transmission from the color release motor error is faulty. Execute U030 [CMY Release]. If the drive from the motor is not transmitted, repair the drive parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 5 Primary transfer belt unit replacement The primary transfer roller lift-up drive section is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2760 |
| Description: | Transfer motor startup error |
| Causes: | The belt motor FG signal is not stable when passing 5s after the transfer motor drive starts. |
| Remedy: | 1 Checking the drive components The drive transmission from the transfer motor is faulty. Check if the excessive load is not applied to the drive gears, rollers and the belt by rotating them, and clean the drive parts of the primary transfer belt unit. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Transfer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Checking the primary transfer belt unit The primary transfer belt unit is not properly installed or faulty Reinstall the primary transfer belt unit. If not repaired, replace it. Detaching and reattaching the primary transfer belt unit 4 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Checking the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2820 |
| Description: | Transfer motor steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the FG signal from the transfer motor at every 1s. |
| Remedy: | 1 Checking the transfer motor The drive transmission from the transfer motor is faulty. Execute U030 [Belt Meand] and check if the drive gears, roller and the belt have no excessive load by rotating them. Then, clean the drive section of the primary transfer belt unit. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Transfer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Checking the primary transfer belt unit The primary transfer belt unit is faulty. Reinstall the primary transfer belt unit. If not repaired, replace it. Detaching and reattaching the primary transfer belt unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 6 Checking the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3100 |
| Description: | Carriage error |
| Causes: | When turning the power on or finishing originals scan through the scanner, the alignment of the home position sensor (turning on / off the sensor) fails and the error is detected. Then, the error is detected twice continuously even the initial operation is executed. |
| Remedy: | 1 Unlocking the scanner mirror frame The scanner mirror frame is not unlocked. Unlock the scanner mirror frame (lamp unit assy). Unlocking the scanner mirror frame 2 Checking the scanner movement A load is applied to the scanner movement. Check the operation of the lamp by U073 or manually moving it. If there is an excess load, check if there are any foreign objects on the optical wire or optical wire drum and clean it. After that, apply grease on the scanner rail. Detaching and reattaching the scanner wires 3 Checking the scanner wires The scanner wires are dirty or come off. Clean and reattach the scanner wires. Detaching and reattaching the scanner wires 4 Checking the scanner motor The scanner motor is faulty. Reattach the scanner motor and reconnect the connector. If not repaired, replace it. 5 Checking the belt tension of the scanner motor A load is applied to the scanner movement since the belt tension is improper. Adjust the scanner motor belt tension properly. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Scanner motor - Engine PWB Wiring diagram 7 Checking the home position sensor The home position sensor is not properly attached. Reattach the home position sensor. 8 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Home position sensor - Engine PWB Wiring diagram 9 Replacing the home position sensor The home position sensor is faulty. Replace the home position sensor. 10 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3200 |
| Description: | LED lamp startup error |
| Causes: | The white reference data acquired by lighting the LED lamp at the initial operation does not reach the specified value. Or, the light amount detected by the CCD PWB is not enough. (2 or more LED lamps do not light. The light does not reach the CCD PWB due to condensation.) |
| Remedy: | 1 Checking the LED lamp The LED lamp does not light. Execute U061 [CCD] and check if the LED lamp is lit. If not, replace the lamp unit. After that, execute U411 [Table(ChartA)]. Detaching and reattaching the lamp unit 2 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB • LED PWB - CCD PWB Wiring diagram 3 Checking the mirror The mirror or lens is frosted due to condensation. Clean the mirrors. If the condensation at the scanner section is resolved naturally by opening the document processor or the platen cover, turn the power switch off and on. 4 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3300 |
| Description: | CCD AGC error (For the internal count) |
| Causes: | Brightness of the LED lamp is darker while one of the LED lamp does not turn on or brighter than expected when processing the AGC for the CCD lamp. |
| Remedy: | 1 Checking the LED lamp The LED lamp is faulty. Check if the LED lamp lights by executing U061 [CCD]. If it does not light, replace the lamp unit and execute U411 [Table (ChartA) ]. Detaching and reattaching the lamp unit 2 Cleaning the backside of the contact glass The white reference sheet is dirty. Clean the white reference sheet at the backside of the contact glass. Detaching and reattaching the contact glass 3 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is peeled off, deformed or the FFC is broken, replace the FFC. • LED PWB - CCD PWB • CCD PWB - Engine PWB Wiring diagram 4 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 5 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3500 |
| Description: | Communication error between the scanner and the ASIC |
| Causes: | The communication error is detected during the communication between the scanner ASIC and the scanner CPU. |
| Remedy: | 1 Resetting the main power ASIC does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3800 |
| Description: | AFE error |
| Causes: | The writing data and the reading data mismatch 3 times continuously when writing. No response is not returned from AFE for 100ms. |
| Remedy: | 1 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is peeled off, deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB Wiring diagram 2 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4001 |
| Description: | Polygon motor synchronization error |
| Causes: | The ready signal is not at the L level when passing 30s after the polygon motor drive starts. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Polygon motor - Engine PWB Wiring diagram 2 Checking the polygon motor The polygon motor does not rotate properly. Check the rotation sound of the polygon motor, and reattach or replace the LSU if it does not rotate properly. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4011 |
| Description: | Polygon motor steady-state error |
| Causes: | The ready signal is at the H level for 15s continuously after the polygon motor drive becomes stable. |
| Remedy: | 1 Checking the connection FFC is not connected properly. Or it is faulty. Clean the FFC terminals of the following FFC and reconnect them. If the FFC terminal is deformed or broken, replace the FFC. • LSU (APC PWB) - Engine PWB Service Manual - Section 8 `PWBs` 2 Checking the polygon motor The polygon motor does not rotate properly. Check the rotation sound of the polygon motor, and reattach or replace the LSU if it does not rotate properly. Detaching and reattaching the LSU 3 Firmware upgrade The engine firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C4101 |
| Description: | BD initialization error |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4102 |
| Description: | BD initialization error C |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • APC PWB C - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4103 |
| Description: | BD initialization error M |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • APC PWB M - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4104 |
| Description: | BD initialization error Y |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • APC PWB Y - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4201 |
| Description: | BD steady-state error |
| Causes: | The BD signal is not detected during the laser lighting. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4600 |
| Description: | LSU cleaning motor error |
| Causes: | The LSU cleaning motor lock-up is detected. Or, the motor continues shifting for 8s or more in the same direction. |
| Remedy: | 1 Executing the Laser Scanner Cleaning The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Execute Laser Scanner Cleaning. 2 Cleaning the LSU cleaning drive gear and the cleaning pad The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Clean the LSU cleaning drive gear and the cleaning pad. 3 Replacing the LSU The LSU cleaning drive gear, cleaning wire or pad is deformed or faulty. Replace the LSU. Detaching and reattaching the LSU 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • LSU cleaning motor - Engine PWB Wiring diagram 5 Checking the LSU cleaning motor The LSU cleaning motor is not properly attached or faulty. Reattach the LSU cleaning motor. If not repaired, replace the motor. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4700 |
| Description: | VIDEO ASIC device error |
| Causes: | 1. The communication with VIDEO ASIC failed 5 times continuously. 2. After writing the data to VIDEO ASIC, the value mismatching error repeated 8 times continuously by trying to read the data from the same address. |
| Remedy: | 1 Resetting the main power The ASIC operation on the PWB is faulty. Turn off the power switch and unplug the power cord. After 5s passes, reconnect the power cord and turn on the power switch. 2 Checking the connection The connector is not properly connected. Reinsert the connectors on the engine PWB all the way. 3 Firmware upgrade The firmware is not the latest version. Upgrade the main firmware and the engine firmware to the latest version. 4 Checking the engine PWB The connector and FFC are not connected properly or the wire, FFC or PWB is faulty. Clean the terminal of the connectors on the engine PWB, reconnect the connector of the wire, and reconnect the FFC terminal. If the wire or the FFC is faulty, repair or replace it. If not resolved, replace the engine PWB. 5 Checking the main PWB The connector and FFC are not connected properly or the wire, FFC or PWB is faulty. Clean the terminal of the connectors on the main PWB, reconnect the connector of the wire, and reconnect the FFC terminal. If the wire or the FFC is faulty, repair or replace them. If not resolved, replace the main PWB. |
| Error code: | C5101 |
| Description: | Main high-voltage error |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the high-voltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Repair the main charger roller contact (wire spring) inside the high-voltage PWB so that it firmly contacts. Detaching and reattaching the high-voltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw does not properly rotate due to the excessive load. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Replacing the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity.• High-voltage PWB - Engine PWB Wiring diagram 7 Replacing the high-voltage PWB The high-voltage PWB is faulty. Replace the high-voltage PWB. Detaching and reattaching the high-voltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5102 |
| Description: | Main high-voltage error C |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5103 |
| Description: | Main high-voltage error M |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5104 |
| Description: | Main high-voltage error Y |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6000 |
| Description: | IH heating error 1 |
| Causes: | The fuser center thermistor temperature does not reach 100°C / 212°F when passing 60s since warm-up starts. Or, the ready display temperature is not detected when passing 420s since the fuser center thermistor temperature reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Executing U169 The IH setting mismatches the power source specification. Set the fuser destination same as the IH PWB voltage at U169. Executing U169 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature cannot be detected properly due to the broken thermostat or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6020 |
| Description: | Fuser center thermistor high temperature error |
| Causes: | The fuser center thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6030 |
| Description: | Fuser center thermistor broken |
| Causes: | The output from the fuser center thermistor is under 20°C / 68°F level during warm-up. Or, the temperature detected at the fuser center thermistor does not change for 10s after turning the fuser heater on. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6040 |
| Description: | Fuser heater error |
| Causes: | The fuser center thermistor outputs the abnormal value for 1s continuously. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6050 |
| Description: | Fuser center thermistor low temperature error |
| Causes: | The fuser center thermistor detects less than 100°C / 212°F for 1s after warm-up, or during print or standby. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 11 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit |
| Error code: | C6200 |
| Description: | Fuser IH ends heating error |
| Causes: | The temperature detected at the fuser edge thermistor does not reach 100°C / 212°F within 60s since warmup starts. The temperature detected at the fuser edge thermistor does not reach the ready display temperature within 60s since it reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. 6 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. Executing U030 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 11 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 12 Replacing the IH unit The IH unit is faulty. Replace the IH unit. |
| Error code: | C6220 |
| Description: | Fuser edge thermistor high temperature error |
| Causes: | The fuser edge thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. 8 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the fuser edge fan motor Dust accumulates on the fuser edge fan motor, or the motor is not properly attached. Clean the front / rear fuser edge fan motors and reattach them. Fan Motors Attachable Direction |
| Error code: | C6230 |
| Description: | Fuser edge thermistor broken |
| Causes: | The fuser edge thermistor detects 37°C / 98°or less for 1s when the fuser center thermistor detects 100°C / 212°F or more for 1s during warm-up. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature cannot be detected properly due to the heater broken or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. 9 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 10 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 11 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6250 |
| Description: | Fuser edge thermistor low temperature error |
| Causes: | The fuser edge thermistor detects less than 100°C / 212°F for 1s during print or standby. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature cannot be detected properly due to the heater broken or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. Detaching and reattaching the fuser IH PWB 9 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 10 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 11 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6400 |
| Description: | Zero-cross signal error • The engine PWB does not detect the zero-crossing signal (Z CROSS SIG) for 5 s. |
| Causes: | Poor contact in the connector terminals. Defective DC power source PWB. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and YC6 on the DC power source PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective DC power source PWB. Check if the zero-crossing signal is output from YC6-3 on the DC power source PWB. If not, replace the DC power source PCB. Defective engine PWB. Replace the engine PWB if C6400 is detected while YC6-3 on the DC power source PWB outputs the zero-crossing signal. |
| Error code: | C6610 |
| Description: | Fuser release sensor error |
| Causes: | 1. The fuser release sensor does not turn off when passing 5s from the instruction to the fuser release motor to reduce the fuser pressure. 2. The fuser release sensor does not turn on when passing 5s from the instruction to the fuser release motor to increase the fuser pressure. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Checking the motor operation / connection The connector is not properly connected. Or, the wire is faulty. Execute U030 [Fuser Release] and check the fuser release motor operation. If the motor does not properly operate, clean the terminal of the following wire connectors and reconnect them. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB Wiring diagram 3 Replacing the fuser unit The fuser release motor or the fuser release sensor, etc. is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6910 |
| Description: | Engine firmware unexpected error |
| Causes: | 1. The engine stable control continued for one hour. 2. The feed motor does not drive when passing 3s or more while the drum motor or developer motor is driving. 3. The only high voltage remote signal turned on while the drum is stopped. 4. The main charge bias turned off while the developer bias turned on. |
| Remedy: | 1 Resetting the main power The power startup delays. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the engine PWB The engine PWB is not properly attached. Or, the connector is not properly connected. Fix the engine PWB with the screw to make sure the grounding and reinsert the connector on the engine PWB all the way. Detaching and reattaching the engine PWB 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7001 |
| Description: | Toner motor error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Toner motor - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7002 |
| Description: | Toner motor C error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner motor C - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7003 |
| Description: | Toner motor M error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner motor M - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7004 |
| Description: | Toner motor Y error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner motor Y - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7101 |
| Description: | Toner sensor error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The drive gears for the developer unit are damaged. (The spiral cannot rotate.) Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7102 |
| Description: | Toner sensor C error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7103 |
| Description: | Toner sensor M error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7104 |
| Description: | Toner sensor Y error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7200 |
| Description: | Internal thermistor broken (For the internal count) |
| Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) exceeds the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
| Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7210 |
| Description: | Internal thermistor short-circuited (For the internal count) |
| Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) is less than the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
| Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7221 |
| Description: | LSU thermistor broken |
| Causes: | The input sampling value of the PD PWB (LSU thermistor) exceeds the reference value. (After the error is detected, the detected temperature is regarded as 23°C / 73°F.) |
| Remedy: | 1 Executing U139 The PD PWB is faulty. Execute U139 [LSU] to check the in-machine temperature around the LSU. (Go to the next step.) Executing U139 2 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • PD PWB (Connects to the APC PWB in the LSU) - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 3 Replacing the LSU The LSU (LSU thermistor) is faulty. Replace the LSU. Detaching and reattaching the LSU 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7231 |
| Description: | LSU thermistor short-circuited |
| Causes: | The input sampling value of the PD PWB (LSU thermistor) is lower than the reference value. (After the error is detected, the detected temperature is regarded as 23 degrees.) |
| Remedy: | 1 Executing U139 The PD PWB is faulty. Execute U139 [LSU] to check the in-machine temperature around the LSU. (Go to the next step.) Executing U139 2 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • PD PWB (Connects to the APC PWB in the LSU) - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 3 Replacing the LSU The LSU (LSU thermistor) is faulty. Replace the LSU. Detaching and reattaching the LSU 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7401 |
| Description: | Developer unit type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in the developer unit does not match the main unit. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB• Front PWB - Engine PWB Wiring diagram 2 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7402 |
| Description: | Developer unit C type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in the developer unit C does not match the main unit. |
| Remedy: | 1 Checking the developer unit The developer unit of the different type is installed. Install the proper developer unit. Detaching and reattaching the developer unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB?• Front PWB - Engine PWB Wiring diagram 3 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7403 |
| Description: | Developer unit M type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in the developer unit M does not match the main unit. |
| Remedy: | 1 Checking the developer unit The developer unit of the different type is installed. Install the proper developer unit. Detaching and reattaching the developer unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB • Front PWB - Engine PWB Wiring diagram 3 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7404 |
| Description: | Developer unit Y type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in the developer unit Y does not match the main unit. |
| Remedy: | 1 Checking the developer unit The developer unit of the different type is installed. Install the proper developer unit. Detaching and reattaching the developer unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB• Front PWB - Engine PWB 3 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7411 |
| Description: | Drum unit type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in drum unit does not match the main unit. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB• Front PWB - Engine PWB Wiring diagram 2 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. Detaching and reattaching the drum unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7412 |
| Description: | Drum unit C type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in drum unit C does not match the main unit. |
| Remedy: | 1 Checking the drum unit and the developer unit The drum unit of the different type is installed. Install the proper drum unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB?• Front PWB - Engine PWB Wiring diagram 3 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. Detaching and reattaching the drum unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. Detaching and reattaching the front PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7413 |
| Description: | Drum unit M type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in drum unit M does not match the main unit. |
| Remedy: | 1 Checking the drum unit and the developer unit The drum unit of the different type is installed. Install the proper drum unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB• Front PWB - Engine PWB Wiring diagram 3 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. Detaching and reattaching the front PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7414 |
| Description: | Drum unit Y type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in drum unit Y does not match the main unit. |
| Remedy: | 1 Checking the drum unit and the developer unit The drum unit of the different type is installed. Install the proper drum unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB• Front PWB - Engine PWB Wiring diagram 3 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. Detaching and reattaching the front PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7601 |
| Description: | Front ID sensor error (For the internal count) |
| Causes: | • Dark potential error: The sensor output value (FrontDarkP and FrontDardS) is less than 0.15V, or more than 0.80V. • Light potential error: FrontBrightS is less than FrontDarkS, or FrontBrightP is less than Front- DarkP+0.5V. |
| Remedy: | 1 Cleaning the front ID sensor The front ID sensor is dirty. Clean the front ID sensor surface. 2 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not properly operate, reattach the cleaning solenoid. Executing U033 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Cleaning solenoid - Relay PWB • Relay PWB - Feed PWB • Feed PWB - Engine PWB Wiring diagram 4 Replacing the cleaning solenoid The cleaning solenoid is faulty. Replace the cleaning solenoid. 5 Checking the front ID sensor The front ID sensor is not properly attached. Reattach the front ID sensor. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Front ID sensor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 7 Replacing the front D sensor The front ID sensor is faulty. Check if the value of U465 [T7 CTD] is fluctuated before and after Calibration, and replace the front ID sensor if it was not fluctuated (uncalibrated) . Executing U465 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7602 |
| Description: | ID sensor error |
| Causes: | • Dark potential error: The sensor output value (FrontDarkP and FrontDardS) is less than 0.15V, or more than 0.80V. • Light potential error: FrontBrightS is less than FrontDarkS, or FrontBrightP is less than Front- DarkP+0.5V. |
| Remedy: | 1 Cleaning the ID sensor The ID sensor is dirty. Clean the ID sensor surface. 2 Checking the ID sensor shutter The ID sensor shutter does not operate properly. If the ID sensor shutter does not operate properly when executing U033 [ID Sensor] , reattach the cleaning solenoid. Executing U033 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Cleaning solenoid - Relay PWB • Relay PWB - Feed PWB • Feed PWB - Engine PWB Wiring diagram 4 Replacing the cleaning solenoid The cleaning solenoid is faulty. Replace the cleaning solenoid 5 Checking the ID sensor The ID sensor is not properly attached. Reattach the ID sensor. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • ID sensor - Feed PWB 7 Replacing the ID sensor The ID sensor is faulty. Check if the value of "T7 CTD" at U465 fluctuates before and after executing Calibration. If not (no adjustment), replace the ID sensor. Executing U465 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7611 |
| Description: | Bias calibration read value error (Black) |
| Causes: | The ID sensors cannot properly read the patch density on the primary transfer belt when executing Calibration or the color adjustment. |
| Remedy: | 1 Resetting the main power The ID sensor does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 (In case if the printout is light) Checking the developer unit (35ppm or faster models) The developing roller does not contact with the drum. Switch the lock lever up and down and return the developer roller to the setting position. If the developer roller does not return due to the breakage of the lock lever or the failure of the developer roller pressure wire, replace the developer unit. Detaching and reattaching the Developer Unit 3 (In case if the printout is light) Checking the connecting gear of the front cover for the maintenance (25/32PPM models) The developer roller does not contact the drum since it does not properly interlock with the opening and closing operation of the front cover for the maintenance. If the developer roller does not contact the drum even if closing the front cover for the maintenance, reattach the gear connecting to the front cover for the maintenance. 4 (In case if the printout is light) Cleaning / replacing the LSU. The laser does not output properly from the LSU. Or, LSU dustproof glass is dirty. Clean the LSU. If not repaired, replace it. Detaching and reattaching the LSU 5 (In case if the printout is light) Improving the condensation of the drum surface (35ppm or faster models) Condensation on the drum surface Execute the drum refresh. And next, set [On] at U339 [Drum heater] to turn on the drum heater. Adjust/ Maintenanc e Menu (Operation Guide - Section 10) Maintenanc e Mode List 6 Cleaning the ID sensor The ID sensor is dirty. Clean the surface of the front and rear ID sensors. 7 Executing Calibration The last calibration failed. Execute U464 [Calib]. Maintenanc e Mode List 8 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not operate properly, reattach the cleaning solenoid. Maintenanc e Mode List 9 Checking the primary transfer unit The primary transfer belt surface is dirty. Clean the surface of the primary transfer belt, or replace the primary transfer unit. Detaching and reattaching the Primary Transfer Unit 10 Checking the ID sensor The ID sensor is not properly attached, or the connector is not properly connected. Reattach the front and rear ID sensors and reconnect the connectors. 11 (When the image is too light) Checking the main high voltage PWB / transfer high voltage PWB Proper current does not flow as the main high voltage PWB or the contact point of the transfer high voltage PWB is faulty. Reattach the main high voltage PWB and the transfer high voltage PWB. 12 (When the image is too light) Checking the drum unit / developer unit / LSU The parts for the drum unit, developer unit and LSU is dirty or worn out. In case if the image is too light, clean the drum unit, developer unit and the LSU. Or, replace them. Maintenanc e parts replacement procedures 13 Firmware upgrade The firmware is not the latest version. Upgrade the firmware to the latest version. Firmware Update 14 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front ID sensor and Rear ID sensor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 15 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 16 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C7612 |
| Description: | Bias calibration read value error (Cyan) |
| Causes: | The ID sensors cannot properly read the patch density on the primary transfer belt when executing Calibration or the color adjustment. |
| Remedy: | 1 Resetting the main power The ID sensor does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 (In case if the printout is light) Checking the developer unit (35ppm or faster models) The developing roller does not contact with the drum. Switch the lock lever up and down and return the developer roller to the setting position. If the developer roller does not return due to the breakage of the lock lever or the failure of the developer roller pressure wire, replace the developer unit. Detaching and reattaching the Developer Unit 3 (In case if the printout is light) Checking the connecting gear of the front cover for the maintenance (25/32PPM models) The developer roller does not contact the drum since it does not properly interlock with the opening and closing operation of the front cover for the maintenance. If the developer roller does not contact the drum even if closing the front cover for the maintenance, reattach the gear connecting to the front cover for the maintenance. 4 (In case if the printout is light) Cleaning / replacing the LSU. The laser does not output properly from the LSU. Or, LSU dustproof glass is dirty. Clean the LSU. If not repaired, replace it. Detaching and reattaching the LSU 5 (In case if the printout is light) Improving the condensation of the drum surface (35ppm or faster models) Condensation on the drum surface Execute the drum refresh. And next, set [On] at U339 [Drum heater] to turn on the drum heater. Adjust/ Maintenanc e Menu (Operation Guide - Section 10) Maintenanc e Mode List 6 Cleaning the ID sensor The ID sensor is dirty. Clean the surface of the front and rear ID sensors. 7 Executing Calibration The last calibration failed. Execute U464 [Calib]. Maintenanc e Mode List 8 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not operate properly, reattach the cleaning solenoid. Maintenanc e Mode List 9 Checking the primary transfer unit The primary transfer belt surface is dirty. Clean the surface of the primary transfer belt, or replace the primary transfer unit. Detaching and reattaching the Primary Transfer Unit 10 Checking the ID sensor The ID sensor is not properly attached, or the connector is not properly connected. Reattach the front and rear ID sensors and reconnect the connectors. 11 (When the image is too light) Checking the main high voltage PWB / transfer high voltage PWB Proper current does not flow as the main high voltage PWB or the contact point of the transfer high voltage PWB is faulty. Reattach the main high voltage PWB and the transfer high voltage PWB. 12 (When the image is too light) Checking the drum unit / developer unit / LSU The parts for the drum unit, developer unit and LSU is dirty or worn out. In case if the image is too light, clean the drum unit, developer unit and the LSU. Or, replace them. Maintenanc e parts replacement procedures 13 Firmware upgrade The firmware is not the latest version. Upgrade the firmware to the latest version. Firmware Update 14 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front ID sensor and Rear ID sensor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 15 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 16 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C7613 |
| Description: | Bias calibration read value error (Magenta) |
| Causes: | The ID sensors cannot properly read the patch density on the primary transfer belt when executing Calibration or the color adjustment. |
| Remedy: | 1 Resetting the main power The ID sensor does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 (In case if the printout is light) Checking the developer unit (35ppm or faster models) The developing roller does not contact with the drum. Switch the lock lever up and down and return the developer roller to the setting position. If the developer roller does not return due to the breakage of the lock lever or the failure of the developer roller pressure wire, replace the developer unit. Detaching and reattaching the Developer Unit 3 (In case if the printout is light) Checking the connecting gear of the front cover for the maintenance (25/32ppm models) The developer roller does not contact the drum since it does not properly interlock with the opening and closing operation of the front cover for the maintenance. If the developer roller does not contact the drum even if closing the front cover for the maintenance, reattach the gear connecting to the front cover for the maintenance. 4 (In case if the printout is light) Cleaning / replacing the LSU. The laser does not output properly from the LSU. Or, LSU dustproof glass is dirty. Clean the LSU. If not repaired, replace it. Detaching and reattaching the LSU 5 (In case if the printout is light) Improving the condensation of the drum surface (35ppm or faster models) Condensation on the drum surface Execute the drum refresh. And next, set [On] at U339 [Drum heater] to turn on the drum heater. Adjust/ Maintenanc e Menu (Operation Guide - Section 10) Maintenanc e Mode List 6 Cleaning the ID sensor The ID sensor is dirty. Clean the surface of the front and rear ID sensors. 7 Executing Calibration The last calibration failed. Execute U464 [Calib]. Maintenanc e Mode List 8 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not operate properly, reattach the cleaning solenoid. Maintenanc e Mode List 9 Checking the primary transfer unit The primary transfer belt surface is dirty. Clean the surface of the primary transfer belt, or replace the primary transfer unit. Detaching and reattaching the Primary Transfer Unit 10 Checking the ID sensor The ID sensor is not properly attached, or the connector is not properly connected. Reattach the front and rear ID sensors and reconnect the connectors. 11 (When the image is too light) Checking the main high voltage PWB / transfer high voltage PWB Proper current does not flow as the main high voltage PWB or the contact point of the transfer high voltage PWB is faulty. Reattach the main high voltage PWB and the transfer high voltage PWB. 12 (When the image is too light) Checking the drum unit / developer unit / LSU The parts for the drum unit, developer unit and LSU is dirty or worn out. In case if the image is too light, clean the drum unit, developer unit and the LSU. Or, replace them. Maintenanc e parts replacement procedures 13 Firmware upgrade The firmware is not the latest version. Upgrade the firmware to the latest version. Firmware Update 14 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front ID sensor and Rear ID sensor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 15 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 16 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C7614 |
| Description: | Bias calibration read value error (Yellow) |
| Causes: | The ID sensors cannot properly read the patch density on the primary transfer belt when executing Calibration or the color adjustment. |
| Remedy: | 1 Resetting the main power The ID sensor does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 (In case if the printout is light) Checking the developer unit (35ppm or faster models) The developing roller does not contact with the drum. Switch the lock lever up and down and return the developer roller to the setting position. If the developer roller does not return due to the breakage of the lock lever or the failure of the developer roller pressure wire, replace the developer unit. Detaching and reattaching the Developer Unit 3 (In case if the printout is light) Checking the connecting gear of the front cover for the maintenance (25/32PPM models) The developer roller does not contact the drum since it does not properly interlock with the opening and closing operation of the front cover for the maintenance. If the developer roller does not contact the drum even if closing the front cover for the maintenance, reattach the gear connecting to the front cover for the maintenance. 4 (In case if the printout is light) Cleaning / replacing the LSU. The laser does not output properly from the LSU. Or, LSU dustproof glass is dirty. Clean the LSU. If not repaired, replace it. Detaching and reattaching the LSU 5 (In case if the printout is light) Improving the condensation of the drum surface (35ppm or faster models) Condensation on the drum surface Execute the drum refresh. And next, set [On] at U339 [Drum heater] to turn on the drum heater. Adjust/ Maintenanc e Menu (Operation Guide - Section 10) Maintenanc e Mode List 6 Cleaning the ID sensor The ID sensor is dirty. Clean the surface of the front and rear ID sensors. 7 Executing Calibration The last calibration failed. Execute U464 [Calib]. Maintenanc e Mode List 8 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not operate properly, reattach the cleaning solenoid. Maintenanc e Mode List 9 Checking the primary transfer unit The primary transfer belt surface is dirty. Clean the surface of the primary transfer belt, or replace the primary transfer unit. Detaching and reattaching the Primary Transfer Unit 10 Checking the ID sensor The ID sensor is not properly attached, or the connector is not properly connected. Reattach the front and rear ID sensors and reconnect the connectors. 11 (When the image is too light) Checking the main high voltage PWB / transfer high voltage PWB Proper current does not flow as the main high voltage PWB or the contact point of the transfer high voltage PWB is faulty. Reattach the main high voltage PWB and the transfer high voltage PWB. 12 (When the image is too light) Checking the drum unit / developer unit / LSU The parts for the drum unit, developer unit and LSU is dirty or worn out. In case if the image is too light, clean the drum unit, developer unit and the LSU. Or, replace them. Maintenanc e parts replacement procedures 13 Firmware upgrade The firmware is not the latest version. Upgrade the firmware to the latest version. Firmware Update 14 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front ID sensor and Rear ID sensor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 15 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 16 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C7620 |
| Description: | Automatic color registration error |
| Causes: | 1. The patch print position on the primary transfer belt is not within the readable area by the ID sensor. 2. The primary transfer belt surface is dirty, or the patch print density is too light. |
| Remedy: | 1 Resetting the main power The ID sensor does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing Calibration The last calibration failed. Execute U464 [Calib]. Maintenanc e Mode List 3 (In case if the printout is light) Checking the developer unit (35ppm or faster models) The developing roller does not contact with the drum. Switch the lock lever up and down and return the developer roller to the setting position. If the developer roller does not return due to the breakage of the lock lever or the failure of the developer roller pressure wire, replace the developer unit. Detaching and reattaching the Developer Unit 4 (In case if the printout is light) Checking the connecting gear of the front cover for the maintenance (25/32PPM models) The developer roller does not contact the drum since it does not properly interlock with the opening and closing operation of the front cover for the maintenance. If the developer roller does not contact the drum even if closing the front cover for the maintenance, reattach the gear connecting to the front cover for the maintenance. 5 (In case if the printout is light) Cleaning / replacing the LSU. The laser does not output properly from the LSU. Or, LSU dustproof glass is dirty. Clean the LSU. If not repaired, replace it. Detaching and reattaching the LSU 6 (In case if the printout is light) Improving the condensation of the drum surface (35ppm or faster models) Condensation on the drum surface Execute the drum refresh. And next, set [On] at U339 [Drum heater] to turn on the drum heater. Adjust/ Maintenanc e Menu (Operation Guide - Section 10) Maintenanc e Mode List 7 Cleaning the ID sensor The ID sensor is dirty. Clean the surface of the front and rear ID sensors. 8 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not operate properly, reattach the cleaning solenoid. Maintenanc e Mode List 9 Checking the primary transfer unit The primary transfer belt surface is dirty. Clean the surface of the primary transfer belt, or replace the primary transfer unit. Detaching and reattaching the Primary Transfer Unit 10 (When the image is too light) Checking the main high voltage PWB / transfer high voltage PWB Proper current does not flow as the main high voltage PWB or the contact point of the transfer high voltage PWB is faulty. Reattach the main high voltage PWB and the transfer high voltage PWB. 11 (When the color registration occurs) Checking the LSU / drum unit LSU or drum unit is not installed correct position. Or, LSU is faulty. If the color registration occurs, reinstall the LSU and the drum unit at the proper position. If not repaired, replace the LSU. Detaching and reattaching the Drum Unit Detaching and reattaching the LSU 12 Checking the ID sensor The ID sensor is not properly attached, or the connector is not properly connected. Reattach the front and rear ID sensors and reconnect the connectors. 13 Firmware upgrade The firmware is not the latest version. Upgrade the firmware to the latest version. Firmware Update 14 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front ID sensor and Rear ID sensor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 15 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 16 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C7800 |
| Description: | Outer thermistor broken (For the internal count) |
| Causes: | The external temperature sensor (external thermistor) cannot be accessed. No response is received from the external thermistor 5 times continuously for 5ms or more when accessing the external thermistor. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Room temperature sensor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Replacing the external temperature sensor The external temperature sensor is faulty. Replace the external temperature sensor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7810 |
| Description: | Short-circuited external thermistor • The thermistor input value is 0.5 V or less. |
| Causes: | Poor contact in the connector terminals. Defective humidity sensor. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC13 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective humidity sensor. Replace the humidity sensor. Defective engine PWB. Replace the engine PWB. |
| Error code: | C7901 |
| Description: | Drum unit EEPROM error |
| Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB • Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7902 |
| Description: | Drum unit C EEPROM error |
| Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB • Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7903 |
| Description: | Drum unit M EEPROM error |
| Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB?• Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7904 |
| Description: | Drum unit Y EEPROM error |
| Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB?• Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7911 |
| Description: | Developer unit EEPROM error |
| Causes: | The toner sensor (EEPROM) in the developing unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit - Front PWB • Front PWB - Engine PWB Wiring diagram 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7912 |
| Description: | Developer unit C EEPROM error |
| Causes: | The toner sensor (EEPROM) in the developing unit C cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit C - Front PWB • Front PWB - Engine PWB 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7913 |
| Description: | Developer unit M EEPROM error |
| Causes: | The toner sensor (EEPROM) in the developing unit M cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit M - Front PWB • Front PWB - Engine PWB 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7914 |
| Description: | Developer unit Y EEPROM error |
| Causes: | The toner sensor (EEPROM) in the developing unit Y cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit M - Front PWB • Front PWB - Engine PWB 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C8000 |
| Description: | Fnisher type mismatch problem • Absence of the finisher is detected. |
| Causes: | Different type of the finisher is installed. |
| Remedy: | Install the correct finisher. |
| Error code: | C8090 |
| Description: | DF paddle motor error Object: 4000-sheet finisher |
| Causes: | 1. The DF paddle sensor does not turn on when passing 1s during the DF paddle motor drive. 2. The DF paddle sensor does not turn off after driving for 1s while the sensor is on. |
| Remedy: | 1 Checking the DF paddle drive components The DF paddle drive parts are not properly attached or faulty. Reattach the DF paddle drive parts. If not repaired, replace them. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •DF paddle motor - DF main PWB • DF paddle sensor - DF main PWB Wiring diagram 3 Replacing the DF paddle motor The DF paddle motor is faulty. Execute U240 [Motor] > [Beat]. If the DF paddle motor does not properly operate, replace it. Executing U240 4 Replacing the DF paddle sensor The DF paddle sensor is faulty. Execute U241 [Finisher] > [Lead Paddle]. If the DF paddle sensor does not properly operate, replace it. Executing U241 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8100 |
| Description: | DF eject release motor error Object: 4000-sheet finisher |
| Causes: | 1. The DF paper bundle ejection switch does not turn on when passing 1s while driving the DF ejection release motor. 2. The DF paper bundle ejection switch does not turn off when driving it for 1s after it turns on. |
| Remedy: | 1 Checking the DF paper stack eject unit The eject guide in the DF paper stack eject unit is deformed. Correct the DF paper stack eject unit. 2 Checking the DF paper stack eject unit drive components The DF paper bundle ejection unit drive parts are not properly attached or faulty. Reattach the DF paper bundle eject unit drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF ejection release motor - DF main PWB • DF paper bundle ejection switch - DF main PWB Wiring diagram 4 Replacing the DF eject release motor The DF eject release motor is faulty. Execute U240 [Motor] > [Eject Unlock (HP) ]. If the DF exit release motor does not properly operate, replace it. Executing U240 5 Checking the DF paper stack eject switch The DF paper bundle ejection switch is not properly attached or faulty. Reattach the DF paper bundle ejection switch. If not repaired, replace the switch. 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8140 |
| Description: | Main tray error 1 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 does not turn on when passing 30s while lifting up the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8160 |
| Description: | DF tray motor error 3 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 4 or 5 does not turn on when passing 60s while descending the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 4 - DF main PWB • DF tray sensor 5 (When installing the Folding Unit) - DF main PWB 6 Checking DF tray sensor 4, 5 DF tray sensor 4 or 5 is not properly attached or faulty. Reattach DF tray sensor 4 or 5 and execute U241 [Finisher] > [Tray L-Limit] or [Tray L-Limit (BL) ]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8170 |
| Description: | DF side registration motor 1 error 1 Object: 4000-sheet finisher |
| Causes: | The home position cannot be detected after passing 3s when relocating to the home position. |
| Remedy: | 1 Checking the front DF side registration guide The front DF side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. 5 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8180 |
| Description: | DF side registration motor 1 error 2 Object: 4000-sheet finisher |
| Causes: | J6810/J6811/J6812 (Front DF side registration jam) was detected 2 times continuously. |
| Remedy: | 1 Checking the front DF side registration guide The front side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive components. 3 Replacing the front DF side registration guide drive components The front DF side registration guide drive components are faulty. Replace the front DF side registration guide drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB 5 Checking DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. Executing U240 6 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8190 |
| Description: | DF side registration motor 2 error 1 Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while executing the operation of returning to the home position. |
| Remedy: | 1 Checking the rear DF side registration guide The rear DF side registration guide is not assembled properly. If the rear DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear DF side registration guide drive components The rear DF side registration guide drive parts are not properly attached or faulty. Reattach the rear DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 2 - DF main PWB • DF side registration sensor 2 - DF main PWB 4 Replacing DF side registration motor 2 DF side registration motor 2 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking DF side registration sensor 2 DF side registration sensor 2 is not properly attached or faulty. Reattach DF side registration sensor 2 and execute U241 [Finisher] > [Width Tail HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8200 |
| Description: | DF side registration motor 2 error 2 Object: 4000-sheet finisher |
| Causes: | J6910 (Rear DF side registration jam) is detected twice continuously. |
| Remedy: | 1 Checking the rear DF side registration guide The rear DF side registration guide is not assembled properly. If the rear DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear DF side registration guide drive components The rear side registration guide drive parts are not properly attached or faulty. Reattach the rear DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 2 - DF main PWB • DF side registration sensor 2 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 2 DF side registration motor 2 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 2 does not properly operate, replace it. 5 Checking DF side registration sensor 2 DF side registration sensor 2 is not properly attached or faulty. Reattach DF side registration sensor 2 and execute U241 [Finisher] > [Width Tail HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8210 |
| Description: | DF staple motor front/rear error Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while returning to the home position at the initial operation. |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple unit is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the DF staple unit drive components The DF staple unit drive parts are not properly attached or faulty. Reattach the DF staple unit drive parts. If not repaired, replace the parts. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple motor - DF main PWB • DF staple sensor - DF main PWB Wiring diagram 4 Replacing the DF staple motor The DF staple motor is faulty. Execute U240 [Motor] > [Staple]. If the DF staple motor does not properly operate, replace the DF staple unit. 5 Checking the DF staple sensor The DF staple sensor is not properly attached or faulty. Reattach the DF staple sensor. Then, replace the DF staple unit if the sensor is not fixed. Detaching and reattaching the DF staple unit 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8230 |
| Description: | DF staple motor error Object: 4000-sheet finisher |
| Causes: | J7000 (DF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple cannot operate manually without paper jam, repair the part that restricts the DF staple. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple unit - DF main PWB Wiring diagram 3 Replacing the DF staple unit The DF staple unit is faulty. Replace the DF staple unit. Detaching and reattaching the DF staple unit 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8260 |
| Description: | DF middle motor HP detection error Object: 4000-sheet finisher |
| Causes: | J7900 (DF paddle jam) is detected twice continuously. |
| Remedy: | 1 Checking the DF paddle drive components The DF paddle drive parts are not properly attached or faulty. Reattach or replace the DF paddle drive components. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF middle motor - DF main PWB • DF paddle sensor - DF main PWB Wiring diagram 3 Replacing the DF middle motor The DF middle motor is faulty. Execute U240 [Motor] > [Middle (H) ] or [Middle (L) ]. If the DF middle motor does not properly operate, replace it. Executing U240 4 Checking the DF paddle sensor The DF paddle sensor is not properly attached or faulty. Reattach the DF paddle sensor and execute U241 [Finisher] > [Lead Paddle]. If the sensor does not properly operate, replace it. Executing U241 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8500 |
| Description: | Main program error (Mail Box) / Mail Box communication error Object: 4000-sheet finisher + Mail box |
| Causes: | The main program of the mail box is faulty when turning the power on. The communication error appears 10 times continuously after finishing the mail box firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the MB firmware and the DF firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB main PWB - DF main PWB 4 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8510 |
| Description: | MB conveying motor error 1 Object: 4000-sheet finisher + Mail box |
| Causes: | The MB home position sensor does not turn on after passing 5s during the initial operation. |
| Remedy: | 1 Checking the MB conveying roller The MB conveying roller is not assembled properly. If the MB conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB conveying motor - MB main PWB • MB home position sensor - MB main PWBPWB Wiring diagram 3 Replacing the MB conveying motor The MB conveying motor is faulty. Execute U240 [Mail Box] > [Conv]. If the MB conveying motor does not properly operate, replace it. 4 Checking the MB home position sensor The MB home position sensor is not properly attached or faulty. Reattach the MB home position sensor and execute U241 [Mail Box] > [Motor HP]. If the sensor does not properly operate, replace it. Executing U241 5 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. |
| Error code: | C8520 |
| Description: | MB conveying motor error 2 Object: 4000-sheet finisher + Mail box |
| Causes: | The MB home position sensor does not turn off after passing 1s during the standby operation. |
| Remedy: | 1 Checking the MB conveying roller The MB conveying roller is not assembled properly. If the MB conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the MB conveying roller drive components The MB conveying roller drive parts are not properly attached or faulty. Reattach the MB conveying roller drive components. 3 Replacing the MB conveying roller drive components The MB conveying roller drive components are faulty. Replace the MB conveying roller drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB conveying motor - MB main PWB • MB home position sensor - MB main PWBPWB 5 Replacing the MB conveying motor The MB conveying motor is faulty. Execute U240 [Mail Box] > [Conv]. If the MB conveying motor does not properly operate, replace it. Executing U240 6 Checking the MB home position sensor The MB home position sensor is not properly attached or faulty. Reattach the MB home position sensor and execute U241 [Mail Box] > [Motor HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. |
| Error code: | C8800 |
| Description: | Main program error (DF) / Engine - DF communication error Object: 4000-sheet finisher |
| Causes: | The main program is faulty when turning on the power. The Engine -DF communication error is detected 10 times continuously. |
| Remedy: | 1 Resetting the main power The program does not start up properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the DP firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • DF main PWB - Engine PWB Wiring diagram 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C8900 |
| Description: | DF backup error Object: 4000-sheet finisher (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • DF main PWB - Engine PWB Wiring diagram 2 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C9180 |
| Description: | DP feed-shift motor error Object: Mechanically reversed DP with the DP feed belt Remarks: When detecting the DP feed-shift motor error (C9180) (up to 2 times), display J9002. |
| Causes: | HP can`t be detected even after the retrying process for the HP detection of the DP feed-shift guide for 3 times continuously. * HP detection of the DP feed-shift guide: When the DP feed-shift motor moves to HP, if HP can`t be detected even driving the DP feed-shift motor for 1 round, the retry is done. |
| Remedy: | 1 Removing the original The original accordion jam in the guide between the DP reversing tray and the DP registration roller (The position is not visible when the DP upper cover is opened) Remove the original which is stuck in the guide between the DP reversing tray and DP registration roller. 2 Cleaning the original conveying guide. Sticky foreign objects adhere to the original conveying guide Clean the original conveying guide. 3 Resetting the main power The DP feed-shift motor is not controlled correctly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 4 Checking the DP feed-shift motor The DP feed-shift motor is not rotated correctly. Or, there is an excess load. After removing the DP feed-shift motor and repair it by rotating the drive section manually, reattach it. 5 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the connector terminal of the wire and reconnect. If there is no continuity, replace the wire. EDP feed-shift motor - DP PWB EDP feed-shift sensor - DP PWB Service Manual - Section 8 `PWBs` 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the DP feed-shift motor The DP feed-shift motor is faulty. Replace the DP feed-shift motor. 8 Checking the DP feed-shift sensor The DP feed-shift sensor is not attached properly or faulty. Reattach the DP feed-shift sensor. If not repaired, replace it. 9 Replacing the DP PWB The DP PWB is faulty. Replace the DP PWB. Detaching and reattaching the DF PWB |
| Error code: | C9500 |
| Description: | Image processing circuit error (Scanner) |
| Remedy: | 1 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • Engine PWB - Main PWB Wiring diagram 2 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C9540 |
| Description: | Backup data error |
| Causes: | When multiple parts are replaced at the same time, the internal data is changed and it interferes with the machine operation. Consequently, the main unit cannot recover. |
| Remedy: | 1 Checking the PWB Multiple PWBs were replaced at the same time. Recover to the original, if 2 or more of the following related parts were replaced at the same time. • Related parts: Memory, each PWB 2 Checking the unit Multiple units were replaced at the same time. Be sure not to perform the following works at the same time when the memory or each PWB is replaced. • Replacing the drum unit or the developer unit • Relocating the drum units to other colorspositioninsideamainunit` |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
