Lexmark X925
Рейтинг
Модули
Flatbed and ADF
PAPER FEED
Paper exit
Base 1
Printhead controller board cables
550 sheet option feeder paper feed
Electrical 1
550 sheet option feeder base
Duplex components 2
Fuser
Paper trays
Duplex components 1
ADF 1
550 sheet option feeder tray
550 sheet option feeder covers
Flatbed
Upper assembly
Base 2
ADF 2
COVERS
Electrical 2
Base 3
Детали Duplex components 1
| Деталь: | Paperfeed unit |
| Парткод: | 40X6176 |
| Деталь: | Registration sensor cable |
| Парткод: | 40X6193 |
| Деталь: | PHOTO SENSOR |
| Парткод: | 40X1104 |
| Деталь: | Registration sensor actuator spring |
| Парткод: | 40X6189 |
| Деталь: | REGISTRATION SENSOR ACTUATOR |
| Парткод: | 40X6188 |
| Деталь: | STATIC DISCHARGE BRUSH |
| Парткод: | 40X6195 |
| Деталь: | Standard registration roller |
| Парткод: | 40X6581 |
| Деталь: | MPF registration roller |
| Парткод: | 40X6580 |
| Деталь: | Registration gear |
| Парткод: | 40X6185 |
| Деталь: | Lower registration spring |
| Парткод: | 40X6183 |
| Деталь: | Upper registration spring |
| Парткод: | 40X6184 |
| Деталь: | FEED ROLL |
| Парткод: | 40X6179 |
| Деталь: | Feed roll gear |
| Парткод: | 40X6177 |
| Деталь: | Pickup gear |
| Парткод: | 40X6178 |
| Деталь: | Pick roll |
| Парткод: | 40X6180 |
| Деталь: | Separator roll |
| Парткод: | 40X6186 |
| Деталь: | TORQUE LIMITER |
| Парткод: | 40X6187 |
| Деталь: | Pickup lever A |
| Парткод: | 40X6181 |
| Деталь: | Registration sensor cable |
| Парткод: | 40X6190 |
| Деталь: | Upper registration spring |
| Парткод: | 40X6422 |
| Деталь: | Lower registration spring |
| Парткод: | 40X6423 |
| Деталь: | Paperfeed clutch |
| Парткод: | 40X6191 |
| Деталь: | Paperfeed clutch cable |
| Парткод: | 40X6194 |
| Деталь: | Paperfeed unit motor |
| Парткод: | 40X6192 |
| Деталь: | Engine paperfeed cable |
| Парткод: | 40X6367 |
| Деталь: | Paperfeed maintenance kit |
| Парткод: | 40X6372 |
| Деталь: | Paper feed screw parts pack |
| Парткод: | 40X7447 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | 40X6579 |
| Деталь: | Photo sensor (exit sensor) |
| Парткод: | 40X1104 |
| Деталь: | Exit sensor cable |
| Парткод: | 40X6168 |
| Деталь: | Paper exit Guide |
| Парткод: | 40X6745 |
| Деталь: | Main unit drive |
| Парткод: | 40X6173 |
| Деталь: | Photo interrupter cable |
| Парткод: | 40X6261 |
| Деталь: | PHOTO SENSOR |
| Парткод: | 40X1104 |
| Деталь: | Sub frame |
| Парткод: | 40X6160 |
| Деталь: | Belt motor |
| Парткод: | 40X6162 |
| Деталь: | Belt motor cable |
| Парткод: | 40X6262 |
| Деталь: | Drive unit motor |
| Парткод: | 40X6161 |
| Деталь: | Base 1 screw parts pack |
| Парткод: | 40X7052 |
| Деталь: | Registration sensor cable |
| Парткод: | 40X6193 |
| Деталь: | Fuser power cable (110V) |
| Парткод: | 40X6211 |
| Деталь: | Fuser power cable (220V) |
| Парткод: | 40X6440 |
| Деталь: | Paper exit sensor cable |
| Парткод: | 40X6168 |
| Деталь: | Fuser exit sensor cable |
| Парткод: | 40X6278 |
| Деталь: | Printhead controller board |
| Парткод: | 40X6756 |
| Деталь: | Density sensor cable |
| Парткод: | 40X6201 |
| Деталь: | Theta sensor cable |
| Парткод: | 40X6198 |
| Деталь: | Power supply fan cable |
| Парткод: | 40X6210 |
| Деталь: | RIP print controller cable |
| Парткод: | 40X6370 |
| Деталь: | Printhead controller option cable |
| Парткод: | 40X6369 |
| Деталь: | RIP Harness cable |
| Парткод: | 40X6748 |
| Деталь: | Option paperfeed cable |
| Парткод: | 40X6365 |
| Деталь: | Vertical paperfeed sensor |
| Парткод: | 40X1107 |
| Деталь: | Type2 feed roll |
| Парткод: | 40X1111 |
| Деталь: | Horizontal sensor (paperfeed) |
| Парткод: | 40X1173 |
| Деталь: | Retainer clip |
| Парткод: | 40X1106 |
| Деталь: | Option tray feed roll |
| Парткод: | 40X1078 |
| Деталь: | Option tray pick roll |
| Парткод: | 40X1077 |
| Деталь: | Option tray separator roll |
| Парткод: | 40X1079 |
| Деталь: | Torque limiter clutch |
| Парткод: | 40X1080 |
| Деталь: | Timing belt S |
| Парткод: | 40X6235 |
| Деталь: | Timing belt L |
| Парткод: | 40X6237 |
| Деталь: | Opt tray door closed sensor |
| Парткод: | 40X6234 |
| Деталь: | Main interface cable |
| Парткод: | 40X6232 |
| Деталь: | Option paperfeed clutch |
| Парткод: | 40X6236 |
| Деталь: | 550 sheet paperfeed screw parts pack |
| Парткод: | 40X7452 |
| Деталь: | LV fuser power cable |
| Парткод: | 40X6211 |
| Деталь: | HV fuser power cable |
| Парткод: | 40X6440 |
| Деталь: | Theta sensor |
| Парткод: | 40X6197 |
| Деталь: | Theta sensor cable |
| Парткод: | 40X6198 |
| Деталь: | Sensor B/S cleaner |
| Парткод: | 40X6264 |
| Деталь: | Main power button |
| Парткод: | 40X6371 |
| Деталь: | Insulation seal |
| Парткод: | 40X6213 |
| Деталь: | 110 V Low voltage power supply |
| Парткод: | 40X6204 |
| Деталь: | 220 V Low voltage power supply |
| Парткод: | 40X5984 |
| Деталь: | Engine power supply cable |
| Парткод: | 40X6747 |
| Деталь: | Power supply fan cable |
| Парткод: | 40X6210 |
| Деталь: | Sub main power cable |
| Парткод: | 40X6926 |
| Деталь: | MPSP cable (scanner - low volt power supply) |
| Парткод: | 40X6753 |
| Деталь: | RIP power supply cable |
| Парткод: | 40X6752 |
| Деталь: | 110V Scanner power supply |
| Парткод: | 40X6750 |
| Деталь: | 220V Scanner power supply |
| Парткод: | 40X6751 |
| Деталь: | Main power cable |
| Парткод: | 40X6749 |
| Деталь: | Sensor A/S cleaner |
| Парткод: | 40X6263 |
| Деталь: | Sensor Cover |
| Парткод: | 40X6266 |
| Деталь: | Sensor cover spring |
| Парткод: | 40X6265 |
| Деталь: | DENSITY SENSOR |
| Парткод: | 40X6199 |
| Деталь: | Density sensor cable |
| Парткод: | 40X6201 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | 40X6202 |
| Деталь: | Humidity sensor cable |
| Парткод: | 40X6203 |
| Деталь: | Paper size sensors |
| Парткод: | 40X6428 |
| Деталь: | MAIN FAN |
| Парткод: | 40X6206 |
| Деталь: | Power supply fan |
| Парткод: | 40X6205 |
| Деталь: | HVT cable |
| Парткод: | 40X6425 |
| Деталь: | RIP Harness cable |
| Парткод: | 40X6748 |
| Деталь: | RIP print controller cable |
| Парткод: | 40X6370 |
| Деталь: | RIP board |
| Парткод: | 40X6317 |
| Деталь: | Engine board fan |
| Парткод: | 40X6427 |
| Деталь: | High volt power supply cable |
| Парткод: | 40X6208 |
| Деталь: | High volt power supply |
| Парткод: | 40X6212 |
| Деталь: | UICC - RIP cable |
| Парткод: | 40X6305 |
| Деталь: | USB front reader cable |
| Парткод: | 40X6309 |
| Деталь: | USB card reader cable |
| Парткод: | 40X6310 |
| Деталь: | RIP - scanner FFC cable (ribbon cable) |
| Парткод: | 40X6311 |
| Деталь: | RIP scanner cable |
| Парткод: | 40X6312 |
| Деталь: | Modem card |
| Парткод: | 40X7055 |
| Деталь: | Electrical screw parts pack |
| Парткод: | 40X7448 |
| Деталь: | UL1 Interface cable |
| Парткод: | 40X6361 |
| Деталь: | UL2 Interface cable |
| Парткод: | 40X6362 |
| Деталь: | Option switch sensor |
| Парткод: | 40X6430 |
| Деталь: | Rising unit hub |
| Парткод: | 40X6358 |
| Деталь: | Rising unit spring |
| Парткод: | 40X6359 |
| Деталь: | TIMING BELT |
| Парткод: | 40X6360 |
| Деталь: | Option interface board |
| Парткод: | 40X6231 |
| Деталь: | Main interface cable |
| Парткод: | 40X6232 |
| Деталь: | Stepper motor cable |
| Парткод: | 40X6233 |
| Деталь: | Option stepper motor |
| Парткод: | 40X6230 |
| Деталь: | Opt tray paper lift motor |
| Парткод: | 40X6229 |
| Деталь: | 550 sheet paperfeed screw parts pack |
| Парткод: | 40X7452 |
| Деталь: | MPF roll |
| Парткод: | 40X6578 |
| Деталь: | MPF Maintenance kit |
| Парткод: | 40X6457 |
| Деталь: | MPF separator spring |
| Парткод: | 40X6412 |
| Деталь: | MPF pad holder |
| Парткод: | 40X6411 |
| Деталь: | MPF bottom cover |
| Парткод: | 40X6415 |
| Деталь: | MPF catch |
| Парткод: | 40X6414 |
| Деталь: | Sub tray |
| Парткод: | 40X6141 |
| Деталь: | A/S pushing spring |
| Парткод: | 40X6136 |
| Деталь: | Duplex cover roller |
| Парткод: | 40X6137 |
| Деталь: | B/S pushing spring |
| Парткод: | 40X6135 |
| Деталь: | RIGHT COVER |
| Парткод: | 40X6134 |
| Деталь: | Safety spring |
| Парткод: | 40X6133 |
| Деталь: | Safety switch rod |
| Парткод: | 40X6127 |
| Деталь: | Door lever lock |
| Парткод: | 40X6128 |
| Деталь: | Lever open spring |
| Парткод: | 40X6131 |
| Деталь: | LEVER SHAFT |
| Парткод: | 40X6130 |
| Деталь: | Door lever |
| Парткод: | 40X6129 |
| Деталь: | LEVER GUIDE |
| Парткод: | 40X6132 |
| Деталь: | Duplex cover pin |
| Парткод: | 40X6983 |
| Деталь: | MPF tray support arm |
| Парткод: | 40X6981 |
| Деталь: | MPF roller bushing |
| Парткод: | 40X6418 |
| Деталь: | Cover 1 screw parts pack |
| Парткод: | 40X6499 |
| Деталь: | Multipurpose tray |
| Парткод: | 40X6223 |
| Деталь: | Main paper tray |
| Парткод: | 40X6219 |
| Деталь: | Tray rack gear |
| Парткод: | 40X6220 |
| Деталь: | Tray pinion gear |
| Парткод: | 40X6221 |
| Деталь: | Cassette screw parts pack |
| Парткод: | 40X7451 |
| Деталь: | MPF Clutch |
| Парткод: | 40X6419 |
| Деталь: | Duplex ground cable |
| Парткод: | 40X6259 |
| Деталь: | PHOTO SENSOR |
| Парткод: | 40X1104 |
| Деталь: | MPF - Engine board cable |
| Парткод: | 40X6416 |
| Деталь: | MPF paper empty lever |
| Парткод: | 40X6982 |
| Деталь: | A/S Carrying roller |
| Парткод: | 40X6152 |
| Деталь: | Duplex roller bushing |
| Парткод: | 40X6147 |
| Деталь: | B/S Carrying roller |
| Парткод: | 40X6153 |
| Деталь: | C/S Carrying roller |
| Парткод: | 40X6154 |
| Деталь: | Discharge brush plate |
| Парткод: | 40X6277 |
| Деталь: | Duplex ground plate |
| Парткод: | 40X6148 |
| Деталь: | Duplex static brush |
| Парткод: | 40X6260 |
| Деталь: | F2/S Transfer spring |
| Парткод: | 40X6159 |
| Деталь: | Transfer roll bushing |
| Парткод: | 40X6143 |
| Деталь: | Roller guide spring |
| Парткод: | 40X6151 |
| Деталь: | Roller guide |
| Парткод: | 40X6258 |
| Деталь: | Transfer roll |
| Парткод: | 40X6012 |
| Деталь: | Duplex clutch cable |
| Парткод: | 40X6158 |
| Деталь: | 2/S Transfer spring |
| Парткод: | 40X6150 |
| Деталь: | Transfer contact plate |
| Парткод: | 40X6149 |
| Деталь: | Inner duplex cover |
| Парткод: | 40X6142 |
| Деталь: | Duplex carrying gear |
| Парткод: | 40X6144 |
| Деталь: | Paper exit sensor lever |
| Парткод: | 40X6145 |
| Деталь: | Duplex timing belt |
| Парткод: | 40X6155 |
| Деталь: | Duplex clutch |
| Парткод: | 40X6157 |
| Деталь: | Drive gear |
| Парткод: | 40X6146 |
| Деталь: | Carry cover |
| Парткод: | 40X6257 |
| Деталь: | Cover 1 screw parts pack |
| Парткод: | 40X6499 |
| Деталь: | ADF input tray |
| Парткод: | 40X6338 |
| Деталь: | Tray paper size sensors |
| Парткод: | 40X6966 |
| Деталь: | ADF tray bottom cover |
| Парткод: | 40X6979 |
| Деталь: | ADF paper stop |
| Парткод: | 40X6345 |
| Деталь: | Upper flatbed top cover |
| Парткод: | 40X6346 |
| Деталь: | Right ADF cover |
| Парткод: | 40X6344 |
| Деталь: | Flatbed hinge |
| Парткод: | 40X6334 |
| Деталь: | Lower flatbed top cover |
| Парткод: | 40X6347 |
| Деталь: | Flatbed cushion |
| Парткод: | 40X6432 |
| Деталь: | ADF HINGE |
| Парткод: | 40X6333 |
| Деталь: | ADF relay card |
| Парткод: | 40X6329 |
| Деталь: | ADF cable |
| Парткод: | 40X6433 |
| Деталь: | ADF relay card cover |
| Парткод: | 40X6342 |
| Деталь: | Left ADF cover |
| Парткод: | 40X6343 |
| Деталь: | Release Arm |
| Парткод: | 40X6542 |
| Деталь: | Idle clutch roller |
| Парткод: | 40X6544 |
| Деталь: | Idle pulley roller |
| Парткод: | 40X6543 |
| Деталь: | ADF screws and fasteners parts pack |
| Парткод: | 40X5867 |
| Деталь: | Option paper tray |
| Парткод: | 40X6246 |
| Деталь: | Right option tray cover |
| Парткод: | 40X6357 |
| Деталь: | DRIVE ROLLER |
| Парткод: | 40X6227 |
| Деталь: | Right front option cover |
| Парткод: | 40X6251 |
| Деталь: | Right rear option cover |
| Парткод: | 40X6252 |
| Деталь: | Right switch cover |
| Парткод: | 40X6254 |
| Деталь: | Stand base foot |
| Парткод: | 40X6224 |
| Деталь: | Left option cover |
| Парткод: | 40X6250 |
| Деталь: | Rear option cover |
| Парткод: | 40X6248 |
| Деталь: | Rear connector cover |
| Парткод: | 40X6249 |
| Деталь: | Upper front option cover |
| Парткод: | 40X6255 |
| Деталь: | Right middle option cover |
| Парткод: | 40X6253 |
| Деталь: | Photo interrupter (Horizontal sensor) |
| Парткод: | 40X1173 |
| Деталь: | 550 sheet paperfeed screw parts pack |
| Парткод: | 40X7452 |
| Деталь: | Flatbed upper cover |
| Парткод: | 40X6320 |
| Деталь: | CCD chassis |
| Парткод: | 40X6321 |
| Деталь: | 30 pin FFC ribbon cable |
| Парткод: | 40X6323 |
| Деталь: | 18 pin FFC ribbon cable |
| Парткод: | 40X6324 |
| Деталь: | ICC PCBA |
| Парткод: | 40X6322 |
| Деталь: | UICC (User interface controller card) |
| Парткод: | 40X6973 |
| Деталь: | Button assembly (op panel top) |
| Парткод: | 40X6957 |
| Деталь: | Op panel access cover |
| Парткод: | 40X6959 |
| Деталь: | Op panel bottom |
| Парткод: | 40X6958 |
| Деталь: | 10.2 inch touchscreen display w/haptics |
| Парткод: | 40X6307 |
| Деталь: | Flatbed front cover |
| Парткод: | 40X6978 |
| Деталь: | Model name cover |
| Парткод: | 40X6443 |
| Деталь: | CCD belt |
| Парткод: | 40X6326 |
| Деталь: | Optical paper size sensors |
| Парткод: | 40X6548 |
| Деталь: | Flatbed cover open sensor |
| Парткод: | 40X6325 |
| Деталь: | Op panel light pipe |
| Парткод: | 40X6977 |
| Деталь: | Scanner rubber pad |
| Парткод: | 40X6757 |
| Деталь: | Scanner stopper screw |
| Парткод: | 40X6758 |
| Деталь: | Scanner sub rubber screw |
| Парткод: | 40X6759 |
| Деталь: | Dimension screw |
| Парткод: | 40X6760 |
| Деталь: | SPEAKER ASSEMBLY |
| Парткод: | 40X7117 |
| Деталь: | UICC - Display cable |
| Парткод: | 40X6306 |
| Деталь: | LED printhead assembly |
| Парткод: | 40X6429 |
| Деталь: | LED FFC ribbon cable |
| Парткод: | 40X6216 |
| Деталь: | LED printhead |
| Парткод: | 40X6218 |
| Деталь: | Printhead controller board |
| Парткод: | 40X6756 |
| Деталь: | CONTACT SPRING |
| Парткод: | 40X6215 |
| Деталь: | TONER SENSOR |
| Парткод: | 40X6214 |
| Деталь: | PRCONT option cable |
| Парткод: | 40X6369 |
| Деталь: | Upper assembly screw parts pack |
| Парткод: | 40X7449 |
| Деталь: | Sub unit drive |
| Парткод: | 40X6163 |
| Деталь: | FUSER FAN |
| Парткод: | 40X6742 |
| Деталь: | Fuser duct |
| Парткод: | 40X6170 |
| Деталь: | Exit solenoid bracket |
| Парткод: | 40X6355 |
| Деталь: | Exit drive unit solenoid |
| Парткод: | 40X6165 |
| Деталь: | Engine power supply (Door interlock) cable |
| Парткод: | 40X6368 |
| Деталь: | Door open switch |
| Парткод: | 40X6166 |
| Деталь: | PHOTO SENSOR |
| Парткод: | 40X1104 |
| Деталь: | Fuser exit sensor cable |
| Парткод: | 40X6278 |
| Деталь: | Engine paperfeed cable (Paper exit unit) |
| Парткод: | 40X6367 |
| Деталь: | Exit drive unit motor |
| Парткод: | 40X6164 |
| Деталь: | Tray lift motor cable |
| Парткод: | 40X6209 |
| Деталь: | Paper tray lift motor |
| Парткод: | 40X6172 |
| Деталь: | Base 2 screw parts pack |
| Парткод: | 40X7442 |
| Деталь: | Outer ADF top cover |
| Парткод: | 40X6331 |
| Деталь: | ADF paperpath sensors |
| Парткод: | 40X6531 |
| Деталь: | Paper present sensor actuator |
| Парткод: | 40X6540 |
| Деталь: | Paper in sensor actuator |
| Парткод: | 40X6539 |
| Деталь: | Top cover release handle |
| Парткод: | 40X6340 |
| Деталь: | Inner ADF top cover |
| Парткод: | 40X6332 |
| Деталь: | ADF pick roll assembly |
| Парткод: | 40X6327 |
| Деталь: | ADF separator roll |
| Парткод: | 40X6328 |
| Деталь: | Mylar ADF pad |
| Парткод: | 40X6953 |
| Деталь: | ADF media paperpath guide |
| Парткод: | 40X6349 |
| Деталь: | Duplex timing sensor |
| Парткод: | 40X6976 |
| Деталь: | Gear w/spring holder |
| Парткод: | 40X6532 |
| Деталь: | Spur G28T gear |
| Парткод: | 40X6538 |
| Деталь: | Spur G63-27T gear |
| Парткод: | 40X6537 |
| Деталь: | Spur G36T gear |
| Парткод: | 40X6536 |
| Деталь: | Duplex out sensor actuator |
| Парткод: | 40X6974 |
| Деталь: | Duplex out sensor |
| Парткод: | 40X6975 |
| Деталь: | Scan sensor w/ paper in sensor |
| Парткод: | 40X6534 |
| Деталь: | Scan sensor actuator |
| Парткод: | 40X6535 |
| Деталь: | ADF main feeder |
| Парткод: | 40X6348 |
| Деталь: | ADF drive clutch |
| Парткод: | 40X6335 |
| Деталь: | ADF solenoid |
| Парткод: | 40X6434 |
| Деталь: | ADF motor frame w/motors |
| Парткод: | 40X6330 |
| Деталь: | Cover open sensor actuator |
| Парткод: | 40X6541 |
| Деталь: | Idle roller w/shaft |
| Парткод: | 40X6533 |
| Деталь: | Separator roll lock |
| Парткод: | 40X6547 |
| Деталь: | Roller bearing |
| Парткод: | 40X6336 |
| Деталь: | Top cover release hook |
| Парткод: | 40X6341 |
| Деталь: | ADF screws and fasteners parts pack |
| Парткод: | 40X5867 |
| Деталь: | Complete Duplex |
| Парткод: | 40X6126 |
| Деталь: | A/S link arm spring |
| Парткод: | 40X6272 |
| Деталь: | A/S link arm |
| Парткод: | 40X6268 |
| Деталь: | Op panel front cover |
| Парткод: | 40X6303 |
| Деталь: | Op panel front cover w/card reader |
| Парткод: | 40X6302 |
| Деталь: | Paper size sensor cable |
| Парткод: | 40X6120 |
| Деталь: | Paper size sensor |
| Парткод: | 40X6114 |
| Деталь: | Sensor frame |
| Парткод: | 40X6354 |
| Деталь: | Tray stop |
| Парткод: | 40X6121 |
| Деталь: | Transfer belt door (DS Lock) |
| Парткод: | 40X6169 |
| Деталь: | Upper front logo cover |
| Парткод: | 40X6289 |
| Деталь: | RIGHT HINGE |
| Парткод: | 40X6282 |
| Деталь: | FRONT COVER |
| Парткод: | 40X6280 |
| Деталь: | LEFT HINGE |
| Парткод: | 40X6283 |
| Деталь: | LEFT COVER |
| Парткод: | 40X6122 |
| Деталь: | ACCESS COVER |
| Парткод: | 40X6124 |
| Деталь: | Option cable |
| Парткод: | 40X6369 |
| Деталь: | Option cover |
| Парткод: | 40X6125 |
| Деталь: | BACK COVER |
| Парткод: | 40X6298 |
| Деталь: | Cable cover |
| Парткод: | 40X6297 |
| Деталь: | Printer top cover |
| Парткод: | 40X6296 |
| Деталь: | Op panel paper exit guide |
| Парткод: | 40X6743 |
| Деталь: | Output bin full lever |
| Парткод: | 40X6417 |
| Деталь: | B/S link arm spring |
| Парткод: | 40X6273 |
| Деталь: | B/S link arm |
| Парткод: | 40X6269 |
| Деталь: | Safety switch spring |
| Парткод: | 40X6270 |
| Деталь: | Release link |
| Парткод: | 40X6267 |
| Деталь: | Release spring |
| Парткод: | 40X6271 |
| Деталь: | Back cave cover |
| Парткод: | 40X6294 |
| Деталь: | INNER RIGHT COVER |
| Парткод: | 40X6301 |
| Деталь: | UPPER RIGHT COVER |
| Парткод: | 40X6295 |
| Деталь: | Transfer belt |
| Парткод: | 40X6011 |
| Деталь: | RIP cover |
| Парткод: | 40X6292 |
| Деталь: | Cave LED cover |
| Парткод: | 40X6304 |
| Деталь: | MFP cave light assembly |
| Парткод: | 40X6755 |
| Деталь: | Cave light cable |
| Парткод: | 40X6314 |
| Деталь: | Op panel under cover. (used on 40X6743) |
| Парткод: | 40X6744 |
| Деталь: | Upper paper exit cover (used on 40X6743) |
| Парткод: | 40X6293 |
| Деталь: | Cover 1 screw parts pack |
| Парткод: | 40X6499 |
| Деталь: | ENGINE BOARD |
| Парткод: | 40X6746 |
| Деталь: | Engine power supply cable |
| Парткод: | 40X6747 |
| Деталь: | Power supply fan cable |
| Парткод: | 40X6210 |
| Деталь: | Belt motor cable |
| Парткод: | 40X6262 |
| Деталь: | Main fan cable (fan included) |
| Парткод: | 40X6206 |
| Деталь: | Humidity sensor cable |
| Парткод: | 40X6203 |
| Деталь: | Paper size sensor cable |
| Парткод: | 40X6120 |
| Деталь: | Engine board fan cable (fan included) |
| Парткод: | 40X6427 |
| Деталь: | MPF Clutch |
| Парткод: | 40X6419 |
| Деталь: | MPF-Engine board cable |
| Парткод: | 40X6416 |
| Деталь: | Registration sensor cable |
| Парткод: | 40X6190 |
| Деталь: | RIP Harness cable |
| Парткод: | 40X6748 |
| Деталь: | Photo interrupter cable (Belt up/down) |
| Парткод: | 40X6261 |
| Деталь: | Paperfeed clutch cable |
| Парткод: | 40X6194 |
| Деталь: | Exit solenoid cable (w/solenoid) |
| Парткод: | 40X6165 |
| Деталь: | Tray lift motor cable |
| Парткод: | 40X6209 |
| Деталь: | Fuser fan cable (fan included) |
| Парткод: | 40X6171 |
| Деталь: | Engine paperfeed cable |
| Парткод: | 40X6367 |
| Деталь: | Drive unit motor (w/motor) |
| Парткод: | 40X6161 |
| Деталь: | Duplex clutch harness |
| Парткод: | 40X6158 |
| Деталь: | Main power cable |
| Парткод: | 40X6749 |
| Деталь: | Remote off switch cable |
| Парткод: | 40X7454 |
| Деталь: | Cover closed actuator cable |
| Парткод: | 40X7455 |
| Деталь: | Paper tray size switch cable |
| Парткод: | 40X7456 |
| Деталь: | Electrical screw parts pack |
| Парткод: | 40X7448 |
Коды ошибок
111.01
112.01
113.01
114.01
121.01
121.02
121.03
121.04
121.05
126.xx
130.xx
132.00
132.xx
136.xx
140
146.01
146.03
146.04
146.05
149.01
171.01
172.01
173.01
174.01
840.01
840.02
840.03
841.00
841.01
841.02
841.03
841.04
841.05
841.06
842.00 ... 842.02
843.00
844.00
849.01
849.10
900.xx
910.xx
941.01
941.02
941.03
941.04
941.05
950.xx
952.xx
953.xx ... 958.xx
959.xx
960.xx
961.xx
964.xx
975.xx ... 991.xx
Описание
| Error code: | 111.01 |
| Description: | Service printhead error LED printhead (K) failure Open circuit detected in the LED printhead. |
| Remedy: | 1 Check the LED Printhead (K) for proper installation. Is the LED Printhead (K) properly installed? Go to step 2. Install the LED Printhead (K) properly. 2 Check the event log for the history of errors that occurred. 1. Enter the Diagnostics Menu. 2. Navigate to EVENT LOG. 3. Touch Display Event Log. Has any connection-related errors occurred? Go to step “111.02–111.04 LED printhead (K) signal failure”. Replace the LED Printhead (K). Go to “LED printhead removal”. |
| Error code: | 112.01 |
| Description: | Service printhead error LED printhead (C) failure Open circuit detected in the LED printhead. |
| Remedy: | 1 Check the LED Printhead (C) for proper installation. Is the LED Printhead (C) properly installed? Go to step 2. Install the LED Printhead (C) properly. 2 Check the event log for the history of errors that occurred 1. Enter the Diagnostics Menu. 2. Navigate to EVENT LOG. 3. Touch Display Event Log. Has any connection-related errors occurred? Go to step “112.02–112.04 LED printhead (C) signal failure”. Replace the LED Printhead (C). Go to “LED printhead removal”. |
| Error code: | 113.01 |
| Description: | Service printhead error LED printhead (M) failure Open circuit detected in the LED printhead. |
| Remedy: | 1 Check the LED printhead (M) for proper installation. Is the LED printhead (M) properly installed? Go to step 2. Install the LED printhead (M) properly. 2 Check the event log for the history of errors that occurred. 1. Enter the Diagnostics Menu. 2. Navigate to EVENT LOG. 3. Touch Display Event Log. Has any connection-related errors occurred? Go to step “113.02–113.04 LED printhead signal failure (M)”. Replace the LED Printhead (M). Go to “LED printhead removal”. |
| Error code: | 114.01 |
| Description: | Service printhead error LED printhead (Y) failure Open circuit detected in the LED printhead. |
| Remedy: | 1 Check the LED printhead (Y) for proper installation. Is the LED printhead (Y) properly installed? Go to step 2. Install the LED printhead (Y) properly. 2 Check the event log for the history of errors that occurred. 1. Enter the Diagnostics Menu. 2. Navigate to EVENT LOG. 3. Touch Display Event Log. Has any connection-related errors occurred? Go to “113.02–113.04 LED printhead signal failure (M)”. Replace the LED printhead (Y). Go to “LED printhead removal”. |
| Error code: | 121.01 |
| Description: | Service fuser error Encoder pulse fail No change was detected on the speed of the belt for more than 1 second. |
| Remedy: | 1 Check the fuser assembly. Is the above component properly connected? Go to step 2. Replace the connections. 2 Replace the fuser assembly. Go to “Fuser assembly removal”. Does the error remain? Go to step 3. Problem resolved 3 POR the machine. Does the error continue? Replace the upper printer engine PCBA. Go to “Upper printer engine PCBA removal”. Problem resolved |
| Error code: | 121.02 |
| Description: | Thermistor 2 error |
| Remedy: | 1 Is the fuser properly installed? Make sure that it is properly seated. Go to step 2. Reinstall the fuser. 2 Is the fuser cable properly connected to CN19 on the printhead controller board? Go to step 3. Properly connect the connector. 3 Check the fuser cable for continuity. Is there continuity? Problem solved Replace the fuser cable. 4 Replace the printhead controller board. Does this fix the problem? Problem solved Go to step 5. 5 Replace the fuser. Does this fix the problem Problem solved Contact second level support. |
| Error code: | 121.03 |
| Description: | Service fuser error Heat belt (center) disconnection error Open circuit is detected at the fuser heat belt. |
| Remedy: | 1 Check the fuser assembly. Is the above component properly connected? Go to step 2. Remove foreign particles, and replace the connections. 2 Replace the fuser assembly. Go to “Fuser assembly removal”. Does the error remain? Go to step 3. Problem resolved 3 POR the machine. Does the error continue? Replace the upper printer engine PCBA. Go to “Upper printer engine PCBA removal”. Problem resolved |
| Error code: | 121.04 |
| Description: | Service fuser error Heat belt (center) overheat error Temperature in the heat belt has exceeded the limit. |
| Remedy: | 1 Check the fuser assembly. Is the above component properly connected? Go to step 2. Remove foreign particles, and replace the connections. 2 Replace the fuser assembly. Go to “Fuser assembly removal”. Does the error remain? Go to step 3. Problem resolved 3 POR the machine. Does the error continue? Replace the upper printer engine PCBA. Go to “Upper printer engine PCBA removal”. Problem resolved |
| Error code: | 121.05 |
| Description: | Service fuser error Heat belt (rear) disconnection error Open circuit is detected at the fuser heat belt. |
| Remedy: | 1 Check the fuser assembly. Is the above component properly connected? Go to step 2. Remove foreign particles, and replace the connections. 2 Replace the fuser assembly. Go to “Fuser assembly removal”. Does the error remain? Go to step 3. Problem resolved 3 POR the machine. Does the error continue? Replace the upper printer engine PCBA. Go to “Upper printer engine PCBA removal”. Problem resolved |
| Error code: | 126.xx |
| Description: | Power switch error |
| Remedy: | 1 Is the power switch cable properly connected to CN27 on the engine controller board? Properly connect the connector. Go to step 2 2 Replace the power switch. Does this fix the problem? Problem resolved Go to step 3. 3 Replace the engine controller board. Does this fix the problem. Problem resolved Go to step 4. 4 Replace the power switch cable harness. Does this fix the problem? Problem resolved Contact your second level support. |
| Error code: | 130.xx |
| Description: | High voltage power supply error |
| Remedy: | 1 Check CN11 on the printhead controller board, and CN01 on the HVPS for proper connectivity. Are the connection properly connected? Go to step 2 Properly connect the connections. 2 Check the HVPS - printhead controller cable for continuity. Is there continuity? Go to step 4. Go to strep 3. 3 Replace the HVPS-printhead controller cable. Does this resolve the problem? Problem solved Go to step 4. 4 Replace the printhead controller board. Does this resolve the issue? Problem solved Go to step 5. 5 Replace the HVPS. Does this resolve the issue? Problem solved Contact your second level support. |
| Error code: | 132.00 |
| Description: | Density sensor error |
| Remedy: | 1 Is the density sensor cleaner stuck in place Go to step 2 Release the cleaner. Replace if damaged. 2 Is the cable connecting the density sensor to CN14 on the printhead controller board connected securely on both ends. Go to step 3. Securely connect the cable. 3 Check the density sensor cable for continuity. Is there continuity? Go to step 4. Replace the density sensor cable. 4 Replace the density sensor. Does this fix the problem? Problem solved. Replace the printhead controller board. |
| Error code: | 132.xx |
| Description: | Abnormal theta sensor |
| Remedy: | 1 Is the reference pattern for the color plane alignment printing properly on the transfer belt? Go to step 4. Go to step 2. 2 Did all the colors print on the test pattern? Go to step 4. Go to step 3. 3 Replace the LED head of the colors that failed to print. Did this fix the problem? Problem solved Go to step 4. 4 Check CN01 on the HVPS, CN11 on the printhead controller, and the CN1-4 for proper connections. Are the connected properly? Go to step 5. Connect the cables properly. 5 Is the Theta sensor cable connected properly connected to CN 8 on the printhead controller board and Theta sensor? Go to step 6. Properly connect the cable to CN8 on the printhead controller board and Theta sensor. 6 Is the sensor misaligned, the sponge blocking the sensor and the cover opening and closing smoothly? Properly align the sensor and reposition the sponge on the theta sensor cover. Make sure the cover opens and closes smoothly. Go to step 7. 7 Replace the theta sensor Problem solved Go to step 8. 8 Replace the engine controller board. Does this fix the problem? Problem solved Go to step 9. 9 Replace the HVPS. Does this fix the problem? Problem solved. Contact your second level support. |
| Error code: | 136.xx |
| Description: | Temperature humidity sensor error |
| Remedy: | 1 Is CN4 on the MDCONT board securely connected Go to step 2 Connect the cable securely. 2 Replace the humidity sensor cable. Does this fix the problem? Problem solved. Go to step 3. 3 Replace the temperature humidity sensor. Does this fix the problem? Problem solved. Replace the printhead controller board. |
| Error code: | 140 |
| Display: | SVC 140 ERROR |
| Description: | Motor |
| Remedy: | DC motor accel stall - staging - replace the Staging motor. If this does not fix the problem, replace the “System board” |
| Error code: | 146.01 |
| Description: | Tray1 error |
| Remedy: | 1 Check the cable connecting the paper tray lift motor to CN 6 on the engine board. Is the cable properly connected at both ends? Go to step 3 Go to step 2 2 Connect the cable properly at both ends. Does this fix the problem? Problem resolved. Go to step 3. 3 Check the paper tray lift motor for continuity. Is there continuity? Go to step 5. Go to step 4. 4 Replace the paper tray lift motor cable. Does this fix the problem. Problem resolved. Go to step 5. 5 Replace the paper tray lift motor. Does this fix the problem? Problem resolved. Go to step 6. 6 Replace the engine board. Does this fix the problem? Problem resolved. Contact your second level support. |
| Error code: | 146.03 |
| Description: | Tray 3 error |
| Remedy: | 1 Check the cable connecting the option paper tray to the option connector on the back of the printer. Is the cable properly connected on both ends. Go to step 3 Go to step 2 2 Connect the cable properly at both ends. Does this fix the problem? Problem resolved. Go to step 3. 3 Check the option cable’s connection to CN 13 on the printhead controller board. Is it properly connected? Go to step 4. Go to step 5. 4 Check the option cable in the printer for continuity. Is there continuity? Go to step 5. Go to step 6. 5 Replace the option cable. Did this fix the problem? Problem resolved. Go to step 6. 6 Check CN120 on the expansion feeder controller for proper connectivity. Is it properly connected? Go to step 8. Go to step 7. 7 Reconnect the connection at CN120. Did this fix the problem? Problem resolved. Go to step 8. 8 Check the cable connecting CN103 and the paper full sensor for proper connectivity. Is the cable properly connected on both ends? Go to step 10. Go to step 9. 9 Re connect the c11 Replace the paper full sensor cable. Did this fix the problem? Problem solved. Go to step 12. 12 Replace the paper full sensor. Did this fix the issue? Problem solved. Go to step 13. 13 Replace the expansion paper feeder controller board. Did this fix the issue? Problem solved. Go to step 14. 14 Check pins 6 and 7 on CN13 of the printer controller board for + 24V. Is the voltage correct? Contact your second level support. Replace the printer controller boardable at both ends. Did this fix the problem? Problem solved. Go to step 10. 10 Check the paper full sensor cable for continuity. Is there continuity? Go to step 12. Go to step 11. |
| Error code: | 146.04 |
| Description: | Tray 4 error |
| Remedy: | 1 Check CN 121 on the first expansion paper feeder’s expansion feeder controller board for proper connectivity. Is it properly connected? Go to step 3. Go to step 2. 2 Reconnect the cable to CN 121.Did this fix the problem? Problem resolved. Go to step 3. 3 Check CN 120 on the second expansion paper feeder’s expansion feeder controller board for proper connectivity. Is it properly connected? Go to step 5. Go to step 4. 4 Reconnect the cable to CN 120.Did this fix the problem? Problem resolved. Go to step 5. 5 Check CN 103 on the second expansion paper feeder’s expansion feeder controller board for proper connectivity. Is it properly connected? Go to step 7. Go to step 6. 6 Reconnect the cable to CN 103.Did this fix the problem? Problem resolved. Go to step 7. 7 Replace the paper full sensor. Does this fix the problem? Problem resolved. Go to step 8. 8 Replace the expansion paper feeder controller board. Does this fix the problem? Problem resolved. Contact you second level support. |
| Error code: | 146.05 |
| Description: | Tray 5 error |
| Remedy: | 1 Check CN 121 on the second expansion paper feeder’s expansion feeder controller board for proper connectivity. Is it properly connected? Go to step 3. Go to step 2. 2 Reconnect the cable to CN 121.Did this fix the problem? Problem resolved. Go to step 3. 3 Check CN 120 on the third expansion paper feeder’s expansion feeder controller board for proper connectivity. Is it properly connected? Go to step 5. Go to step 4. 4 Reconnect the cable to CN 120.Did this fix the problem? Problem resolved. Go to step 5. 5 Check CN 103 on the third expansion paper feeder’s expansion feeder controller board for proper connectivity. Is it properly connected? Go to step 7. Go to step 6. 6 Reconnect the cable to CN 103.Did this fix the problem? Problem resolved. Go to step 7. 7 Replace the paper full sensor. Does this fix the problem? Problem resolved. Go to step 8. 8 Replace the expansion paper feeder controller board. Does this fix the problem? Problem resolved. Contact you second level support. |
| Error code: | 149.01 |
| Description: | Fuser / paper exit motor error |
| Remedy: | 1 Is the fuser / paper exit motor cable properly connected to the motor and CN16 on the engine board? Go to step 2 Connect the cables at both ends. 2 Check the cable for continuity. Is there continuity? Go to step 3. Replace the fuser/paper exit motor cable. 3 Replace the paper exit/fuser motor. Did this fix the problem? Problem solved. Go to step 4. 4 Replace the engine board. Did this fix the problem? Problem solved. Go to step 5. 5 Replace the printhead controller board. Did this fix the issue? Problem solved. Contact your second level support. |
| Error code: | 171.01 |
| Description: | Service engine error Controller cooling fan failure |
| Remedy: | The controller cooling fan is not functioning. |
| Error code: | 172.01 |
| Description: | Service engine error Front upper cooling fan failure The front upper cooling fan is not functioning. |
| Remedy: | 1 Check the front upper cooling fan. Is the above component properly connected? Go to step 2. Replace the connections. 2 Replace the front upper cooling fan. Go to “Front upper cooling fan removal”. Does the error continue? Go to step 3. Problem resolved 3 POR the machine. Does the error continue? Replace the upper printer engine PCBA. Go to “Upper printer engine PCBA removal”. Problem resolved |
| Error code: | 173.01 |
| Description: | 173.01 Service engine error LVPS cooling fan failure The LVPS cooling fan is not functioning. |
| Remedy: | 1 Check the LVPS sub cooling fan. Is the above component properly connected? Go to step 2. Replace the connections. 2 Replace the LVPS sub cooling fan. Go to “LVPS sub cooling fan removal”. Does the error continue? Go to step 3. Problem resolved 3 POR the machine. Does the error continue? Replace the lower engine PCBA. Go to “Lower engine PCBA removal”. Problem resolved |
| Error code: | 174.01 |
| Description: | Service engine error Rear left lower cooling fan failure The HVPS cooling fan is not functioning. |
| Remedy: | 1 Check the charge roll HVPS cooling fan. Is the above component properly connected? Go to step 2. Replace the connections. 2 Replace the charge roll HVPS cooling fan. Go to “Charge roll HVPS cooling fan removal”. Does the error continue? Go to step 3. Problem resolved 3 POR the machine. Does the error continue? Replace the lower engine PCBA. Go to “Lower engine PCBA removal”. Problem resolved |
| Error code: | 840.01 |
| Description: | The scanner is disabled and can’t be used. |
| Remedy: | Enter the configuration mode to re-enable the scanner. |
| Error code: | 840.02 |
| Description: | The scanner is disabled and can’t be used. |
| Remedy: | Enter the configuration mode to re-enable the scanner. |
| Error code: | 840.03 |
| Description: | Scanner cable has been unplugged. |
| Remedy: | 1 Remove the system board upper shield. See “System board upper shield removal”. Check the cable for proper connection. Remove the ADF rear cover. See “ADF rear cover removal”. Check the cable for proper connection. Remove the scanner rear cover. See “Scanner rear cover removal”. Check the cable for proper connection. Are any of the cables unplugged? Reseat the cable. Go to step 2. 2 Check the cable for damage. Are any of the cables damaged? Replace the cable. Go to step 3. 3 Replace the ADF controller card. See “ADF controller card removal”. Does the error clear? Problem solved. Go to step 4. 4 Replace the scanner interface card. See “Scanner interface card removal”. Does the error clear? Problem solved. Replace the system board. See “System board removal”. |
| Error code: | 841.00 |
| Description: | Service scanner failure Image pipeline ASIC failure The image pipeline for processing the data that comes from the scanner, prior to being printed, has failed. |
| Remedy: | 1 Perform a POR. Does the error occur when the power is turned off/on? Go to step 2. Perform several print tests. If the problem remains, then go to step 2. 2 Turn the printer off for 60 seconds. Does the error occur when the power is turned off/on again? Replace the RIP card assembly. Go to “RIP PCBA removal”. Problem resolved 3 Perform a POR. Does the error occur when the power is turned off/on? Go to step 2. Perform several print tests. If the problem remains, then go to step 2. |
| Error code: | 841.01 |
| Description: | Invalid AFE setting. |
| Remedy: | 1 POR the device a few times. Did the error re-occur? Go to step 2. Problem resolved 2 Check the connections on the 8 and 30 pin cables connecting the CCD to the ICC card. Are the cables properly connected? Go to step 3. Go to step 4. 3 Properly connect the cables. Did this fix the issue? Problem resolved Go to step 4. 4 Check the 8 and 30 pin CCD cables for continuity. Is there continuity? Go to step 6. Go to step 5. 5 Replace the cable that lacked continuity. Did this fix the problem? Problem resolved Go to step 6. 6 Replace the CCD. Did this fix the issue. Problem resolved Go to step 7. 7 Replace the ICC board in the flatbed. Did this fix the issue. Problem solved Replace the RIP board. |
| Error code: | 841.02 |
| Description: | Delayed interrupt detected. |
| Remedy: | 1 POR the device a few times. Did the error re-occur? Go to step 2. Problem resolved 2 Update the firmware. Before doing so, contact your second level support for the correct level firmware to flash the device with. Did this resolve the issue? Problem resolved Go to step 3. 3 Replace the RIP board. Did this fix the issue? Problem resolved Contact second level support. |
| Error code: | 841.03 |
| Description: | Failed indirect register test. |
| Remedy: | 1 POR the device a few times. Did the error re-occur? Go to step 2. Problem resolved 2 Replace the RIP. Did this fix the issue? Problem resolved Contact second level support. |
| Error code: | 841.04 |
| Description: | Failed external DRAM test. |
| Remedy: | 1 POR the device a few times. Did the error re-occur? Go to step 2. Problem resolved 2 Replace the RIP. Did this fix the issue? Problem resolved Contact second level support. |
| Error code: | 841.05 |
| Description: | Image pipe timeout |
| Remedy: | 1 POR the device a few times. Did the error re-occur? Go to step 2. Problem resolved 2 Replace the RIP. Did this fix the issue? Problem resolved Contact second level support. |
| Error code: | 841.06 |
| Description: | Scanner did not initiate scan |
| Remedy: | 1 Check the cables connecting the RIP board to the scanner for damage. Is there any visible damage? Go to step 2. Go to step 3. 2 Replace the faulty cables. Did this fix the problem? Problem resolved Go to step 3. 3 Check the cables for continuity. Is there continuity? Go to step 5. Go to step 4. 4 Replace the faulty cable. Did this fix the problem? Problem resolved Go to step 5. 5 Is the flatbed LED illuminating when the scan command is issued? Go to step 6. Go to step 7. 6 Replace the CCD. Did this fix the problem? Problem resolved Go to step 7. 7 Replace the ICC card. Did this fix the problem? Problem resolved Go to step 8. 8 Replace the RIP board. Did this fix the issue? Problem resolved Contact second level support. |
| Error code: | 842.00 ... 842.02 |
| Description: | 842.00 No response 842.01 HW Protocol 842.02 Logical protocol |
| Remedy: | 1 POR the device. Did the error re-occur? Go to step 2. Problem resolved 2 Check all the connections from the ICC card to the ADF relay card and RIP board to ICC card. Also check the CCD cables for proper connectivity. Are the cables properly connected? Go to step 3 Go to step 4. 3 Properly connect all the cables. Did this fix the issue? Problem resolved Go to step 4. 4 Check the cables for continuity. Is there continuity? Go to Step 6. Go to step 5. 5 Replace the faulty cable. Did this fix the issue? Problem resolved Go to step 6. 6 Is the CCD LED illuminating and not moving when a scan command is given? Replace the CCD. Go to step 7. 7 Replace the ICC card. Did this fix the issue? Problem resolved Go to step 8. 8 Replace the ADF relay card. Did this fix the issue? Problem resolved Go to step 9. 9 Replace the RIP board. Did this fix the issue? Problem resolved Contact your second level support. |
| Error code: | 843.00 |
| Description: | The flatbed scanner carriage home position is not detected by the sensor (flatbed scanner home position). |
| Remedy: | Step 1 Check the ADF to flatbed scanner connection for proper connectivity. Is the above connection properly connected? Go to step 2. Replace the connection. Step 2 Check the sensor (flatbed scanner home position) for damage or detachment. Is the above sensor properly attached or free from damage? Go to step 3. Reattach or replace the sensor (flatbed scanner home position). Step 3 Check the sensor (flatbed scanner home position) for proper operation. a Enter the Diagnostics Menu. b Touch SCANNER TESTS. c Touch Sensor Tests. d See the line item “sensor (flatbed scanner home position).” Does the display on the operator panel change every time the sensing area of the above sensor is interrupted or blocked? Go to step 5. Go to step 4. Step 4 Check the sensor (flatbed scanner home position) for proper connection. Is the above component properly connected? Reattach or replace the sensor (flatbed scanner home position). Replace the connection. Step 5 Check the flatbed scanner drive motor for proper operation. a Enter the Diagnostics Menu. b Touch MOTOR TESTS. c Touch flatbed drive motor. d Perform test. Does the motor operate properly? Go to step 7. Go to step 6. Step 6 Check the flatbed scanner motor for proper connection. Is the above component properly connected? Replace the ADF rear side drive parts pack. Replace the connection. Step 7 Place an undamaged document on the flatbed scanner and perform a scanner test. Does the problem remain? Replace the flatbed scanner controller board. See “Flatbed scanner PCBA removal”. Problem resolved. Step 8 Place an undamaged document on the flatbed scanner and perform a scanner test. Does the problem remain? Replace the ADF controller board. See “ADF controller card removal”. Problem resolved. |
| Error code: | 844.00 |
| Description: | Service scanner failure Exposure lamp failure A failure has occurred with the exposure lamp. |
| Remedy: | 1 Check the exposure lamp for connection. Is the above component connected properly? Replace the exposure lamp. Go to “LED exposure bar removal”. Replace the connection. 2 Perform a POR. Does the error remain when the power is turned off/on? Replace the scanner controller PCBA. Go to “Scanner controller PCBA removal”. Problem resolved |
| Error code: | 849.01 |
| Description: | HD/Config ID Mismatch |
| Remedy: | Uninstall the modem |
| Error code: | 849.10 |
| Description: | Machine has an installed hard drive that should not be present. |
| Remedy: | Uninstall the hard drive. |
| Error code: | 900.xx |
| Description: | RIP software error |
| Remedy: | 1. POR the machine and print a simple test page to determine if the problem is system software related, or if the customer is sending a corrupted print job. 2. Check all connections on the system card assembly. 3. Replace the system card assembly if problem remains. |
| Error code: | 910.xx |
| Description: | DC pick motor stall |
| Remedy: | Turn off printer for 10 seconds and restart. If error re-occurs, replace RIP board. |
| Error code: | 941.01 |
| Description: | Service tray 1 failure sensor (media level) late error (tray 1) The sensing area of the sensor (media level) in the media tray 1 is not interrupted within the specified time after the lift tray has risen to operating level. |
| Remedy: | 1 Check the media. Is media loaded in tray 1 properly? Go to step 2. Load media properly. 2 Check the sensor (media level) (tray 1) for proper operation. 1. Enter the Diagnostics Menu. 2. Touch INPUT TRAY TESTS. 3. Touch Sensor Test. 4. Touch Tray 1. 5. Touch Media level. Does the display on the operator panel, change every time the media tray is opened and closed? Go to step 4. Go to step 3. 3 Check the sensor (media level) (tray 1) for proper connection. Is the above component properly connected? Replace the sensor (media level). Go to “Sensor (media level) removal”. Replace the connection. 4 Check the media feed/lift motor (tray 1) for proper operation. Caution: When performing motor tests, ensure that all cover and door interlock switches are overridden. 1. Enter the Diagnostics Menu. 2. Touch MOTOR TESTS. 3. Touch Tray 1 media feed/lift motor. Warning: The media tray must be opened before performing this test or paper jam may occur. Does the above component operate properly? Go to step 6. Go to step 5. 5 Check the media feed/lift motor (tray 1) for proper connection. Is the above component properly connected? Replace the media feed/lift motor. Go to “Media feed lift motor removal”. Replace the connection. 6 Perform a POR. Does the error continue when the power is turned off/on? Replace the upper printer engine card assembly. Go to “Upper printer engine card assembly removal”. Problem solve |
| Error code: | 941.02 |
| Description: | MDC error |
| Remedy: | 1 Are the cables connecting CN24 on the engine board, CN5 on the printhead controller, and CN03 in the LVPS properly connected? Go to step 3. Go to step 2. 2 Re connect the cables. Did this fix the problem Problem resolved Go to step 3. 3 Check the cables for continuity. Is there continuity? Go to step 5. Go to step 4. 4 Replace the cables. Did this fix the issue? Problem resolved Go to step 5. 5 Check pins 1,3, and 7 on CN03 on the LVPS for +5V, and pins 5, and 9 for +24V. Are the voltages correct? Go to step 7 Go to step 6. 6 Replace the LVPS. Did this fix the problem? Problem resolved Go to step 7 7 Replace the engine board. Does this fix the issue? Problem resolved Go to step 8. 8 Replace the printhead controller board. Did this fix the issue? Problem resolved Contact your second level of support. |
| Error code: | 941.03 |
| Description: | CPU error |
| Remedy: | 1 POR the printer. Does the problem go away? Problem resolved Go to step 2. 2 Replace the printhead controller. Does this fix the problem? Problem resolved Go to step 3. 3 Replace the RIP board. Did this fix the issue? Problem resolved Contact your second level support. |
| Error code: | 941.04 |
| Description: | Abnormal MDC controller |
| Remedy: | 1 Are the cables connecting CN24 on the engine board, CN5 on the printhead controller, and CN03 in the LVPS properly connected? Go to step 3. Go to step 2. 2 Re connect the cables. Did this fix the problem Problem resolved Go to step 3. 3 Check the cables for continuity. Is there continuity? Go to step 5. Go to step 4. 4 Replace the cables. Did this fix the issue? Problem resolved Go to step 5. 5 Check pins 1,3, and 7 on CN03 on the LVPS for +5V, and pins 5, and 9 for +24V. Are the voltages correct? Go to step 7 Go to step 6. 6 Replace the LVPS. Did this fix the problem? Problem resolved Go to step 7 7 Replace the engine board. Does this fix the issue? Problem resolved Go to step 8. 8 Replace the printhead controller board. Did this fix the issue? Problem resolved Contact your second level of support. |
| Error code: | 941.05 |
| Description: | Abnormal EEPROM |
| Remedy: | 1 POR the printer a few times. Did this fix the issue? Problem resolved. Go to step 2. 2 Replace the printhead controller. Does this fix the problem? Problem resolved Go to step 3. 3 Replace the RIP board. Did this fix the issue? Problem resolved Contact your second level support. |
| Error code: | 950.xx |
| Description: | Mismatch between EEPROM and mirror memory |
| Remedy: | Warning: When replacing any of the following components: • Operator panel assembly • System card assembly Only replace one component at a time. Replace the required component and perform a POR before replacing a second component listed above. If this procedure is not followed, the printer will be rendered inoperable. Never replace two or more of the components listed above without a POR after installing each one or the printer will be rendered inoperable. Never install and remove components listed above as a method of troubleshooting components. Once a component has been installed in a machine, it can not be used in another machine. It must be returned to the manufacturer. Go to NVRAM mismatch failure service check. 1 Check the operator panel assembly. Was the operator panel assembly recently replaced? Go to step 3. Go to step 2. 2 Check the system card assembly. Was the system card assembly recently replaced? Go to step 4. Contact next level of support. 3 Replace the current operator panel assembly with the original operator panel assembly. Does the error remain? Go to step 5. Problem solved. 4 Replace the current system card assembly with the original system card assembly. Go to “System card assembly removal (X651, X652, X654, X656, and X658)”. Go to step 6. Problem solved. 5 If problem continues, replace the original operator panel assembly with a new and not previously installed operator panel assembly. Does the error continue? Contact the next level of support. Problem solved. 6 If the problem continues, replace the original panel assembly with a new ann not previously installed operator panel door assembly or the operator panel assembly. Go to “Operator panel door assembly removal (models X651, X652, X654, and X656)”. Go to “Operator panel assembly removal (model X658)”. Contact the next level of support. Problem solved. |
| Error code: | 952.xx |
| Description: | A recoverable NVRAM Cyclic Redundancy Check error occurred. |
| Remedy: | Power the machine off/on to reset the error condition. |
| Error code: | 953.xx ... 958.xx |
| Description: | 953.xx Service NVRAM Failure 954.xx Service NVRAM Failure 955.00 Service Code CRC <loc> 956.xx Service System Board 957.xx Service System Board 958.xx Service NAND Failure |
| Remedy: | Replace the RIP board. For the 958 error, replace the UICC card if replacing the RIP board does not fix the problem. |
| Error code: | 959.xx |
| Description: | Print cartridge authentication failure The system card can not properly authenticate the print cartridge or the authentication process has failed. |
| Remedy: | Replace the system card assembly. |
| Error code: | 960.xx |
| Description: | RAM memory error: RAM soldered on the controller board is bad |
| Remedy: | • POR the printer. • If the problem persists, then replace the controller board. |
| Error code: | 961.xx |
| Description: | RAM memory error: memory card in slot is bad. |
| Remedy: | Replace the bad memory card. |
| Error code: | 964.xx |
| Description: | Download Emulation Cyclic Redundancy Check Error: checksum failure detected in the emulation header or emulation file. |
| Remedy: | 1. Disable the Download Emulation. Program the download emulation into the firmware card again. 2. Replace the system card assembly if problem remains. |
| Error code: | 975.xx ... 991.xx |
| Description: | 975.xx Standard network or Network Card X 976.xx Standard network or Network Card X 982.xx Service <device> 990.xx Service <device> 991.xx Service <device> Card |
| Remedy: | Call your second level support. |
Название
LEXMARK Блок фотобарабана черный
LEXMARK Блок фотобарабана голубой
LEXMARK Блок фотобарабана пурпурный
LEXMARK Блок фотобарабана желтый
LEXMARK Контейнер для отработанного тонера
LEXMARK Тонер-картридж голубой
LEXMARK Тонер-картридж черный
LEXMARK Тонер-картридж пурпурный
LEXMARK Тонер-картридж желтый
