OKI B420dn

Рейтинг

Парткаталог
Коды ошибок

Модули

Frame-Lower-Assy

Front-Guide-Assy

Base-Assy

Stacker-Cover-Assy

MPT-Assy

Rear-Cover-Assy

PCB-Assy

Printer Unit

Детали Frame-Lower-Assy

Деталь:	Frame-SubAssy.-Lower
Парткод:	43993401

Деталь:	Damper-Oil
Парткод:	42596601

Деталь:	Board-TT1
Парткод:	43998001

Деталь:	Lever-In-Sensor
Парткод:	43903301

Деталь:	Spring-Sensor_IN
Парткод:	42797101

Деталь:	Spring-WriteSensor
Парткод:	41415801

Деталь:	Sensor-Toner(Adhesive)
Парткод:	43993601

Деталь:	Lever-Eject-Sensor
Парткод:	43206401

Деталь:	Spring-SNS(F/R)
Парткод:	40386501

Деталь:	PHOTO-INTERRUPTER
Парткод:	40135301

Деталь:	CONN Cord-AMP6P- AMP3PX2
Парткод:	43961401

Деталь:	Roller-Transfer(282)
Парткод:	43979601

Деталь:	Bearing-TR
Парткод:	43330101

Деталь:	Spring-TR
Парткод:	43401401

Деталь:	Lever-Reset-L
Парткод:	43903601

Деталь:	Collar-Reset-Lever
Парткод:	43598801

Деталь:	OR-Roller-Back up
Парткод:	44009501

Деталь:	Spring-Bias
Парткод:	41584101

Деталь:	Holder-BU
Парткод:	43448601

Деталь:	Bearing-Ball
Парткод:	41584201

Деталь:	COLLAR
Парткод:	43448701

Деталь:	COLLAR
Парткод:	43448702

Деталь:	Roller-Registration
Парткод:	43903701

Деталь:	Holder-Regist L
Парткод:	41279501

Деталь:	Holder-Regist R
Парткод:	41279601

Деталь:	Gear-Pressure
Парткод:	41279801

Деталь:	Bearing-Pressure
Парткод:	41279401

Деталь:	Plate-Contact PA
Парткод:	41280401

Деталь:	Gear-Regist
Парткод:	41279701

Деталь:	Bearing-Regist L
Парткод:	41279301

Деталь:	Lever-Reset-R
Парткод:	43904001

Деталь:	Motor-DC-Main
Парткод:	43906601

Деталь:	SOFT GASKET NLCG
Парткод:	44120401

Деталь:	Gear-Assy-Clutch
Парткод:	43905402

Деталь:	Gear-Assy-Clutch
Парткод:	43905403

Коды ошибок

001

002

003

004

005

006

007

020

023

024

030

031

034

040

041

042

043

049

063

070

072

073

074

075

081

0xF0C

0xF0D

0xFFF

104

106

112

120

121

122

123

124

126

127

128

134

153

163

170

171

172

173

182

190

203

204

207

208

209

213

230

231

923

928

982

Деталь:	Frame-Assy.-Separator(Black)
Парткод:	43418002

Деталь:	JST8P-JST8P CONN Cord-Wire
Парткод:	43957601

Деталь:	Guide-Assy.-Front(Black)
Парткод:	43993803

Деталь:	Plate-Assy.-P.C.B.(230V)
Парткод:	43993102

Деталь:	Cover-Assy.-Stacker(Black)
Парткод:	43994804

Error code:	001
Display:	Service Call 001: Error
Description:	Leading edge of the recording paper fails to reach the Timing Sensor. (1st Cassette)
Causes:	Recording paper jam. Timing Sensor abnormal.
Remedy:	Is the error display reproducible? Power OFF/ON Replace CU PCB. (Must replace EEPROM)

Error code:	003
Description:	ISI Exception (Instruction read failure)

Error code:	004
Description:	Alignment Exception (Memory access error)

Error code:	005
Description:	Program Exception (Illegal instruction, trap instruction, privilege violation, and so on)

Error code:	006
Display:	Service call 006: Error
Description:	Floating-point Unavailable Exception
Remedy:	Is the error message displayed again? If the RAM DIMM is mounted, remove it and turn the power supply Off/On. Replace 86M board Remount RAM DIMM Replace RAM DIMM

Деталь:	Roller-BIAS-FU
Парткод:	43222001

Деталь:	Roller-Pinch
Парткод:	43355101

Деталь:	Spring-Separator
Парткод:	42069901

Деталь:	Frame-Assy.-Separator
Парткод:	43418001

Error code:	007
Display:	Service call 007: Error
Description:	1. Leading edge of the recording paper fails to reach the Paper Exit Sensor. 2. Recording paper has not completely passed the Paper Exit Sensor.
Causes:	Recording paper jam. Paper Exit Sensor abnormal.
Remedy:	Is the error message displayed again? If the RAM DIMM is mounted, remove it and turn the power supply Off/On. Replace 86M board Remount RAM DIMM Replace RAM DIMM

Error code:	020
Display:	Service Call 020: Error
Description:	CU ROM Hash Check Error 1
Causes:	Is program ROM DIMM set properly? Is error recovered by replacing program ROM DIMM?
Remedy:	Reset program ROM DIMM. Replace program ROM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	023
Display:	Service call 023: Error
Description:	CU Font ROM Hash error
Causes:	Does error display reappear?
Remedy:	Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.

Error code:	024
Display:	Service Call 024:Error
Description:	CU Font ROM Hash Error
Causes:	Does this error message reappear?
Remedy:	Does this error message reappear? Yes Power OFF/ON. Replace the printer control PCB.

Error code:	030
Display:	Service Call 030: Error
Description:	CU Slot1 DIMM RAM Check Error
Causes:	Is subject RAM DIMM set properly? Is error recovered by replacing subject ROM DIMM?
Remedy:	Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	031
Display:	Service Call 031: Error
Description:	CU Slot2 DIMM RAM Check Error
Causes:	Is subject RAM DIMM set properly? Is error recovered by replacing subject ROM DIMM?
Remedy:	Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	034
Display:	Service call 034: Error
Description:	RAM Configuration Error
Remedy:	RAM Configuration Error

Error code:	040
Display:	Service Call 040: Error
Description:	CU EEPROM Error
Causes:	Is error recovered by replacing EEPROM on CU board?
Remedy:	Replace EEPROM. (Recover user environment.) Replace TIG board. (Replace EEPROM)

Error code:	041
Display:	Service Call 041: Error
Description:	CU Flash Error Flash ROM error on CU board.
Causes:	Does error display reappear?
Remedy:	Replace TIG board. (Replace EEPROM.)

Error code:	042
Display:	Inspection is required. 042:Error
Description:	Flash File System Error
Causes:	Does this error message reappear?

OKI B420dn

Модули

Детали Frame-Lower-Assy

Коды ошибок

Описание

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	043
Display:	Inspection is required. 043:Error
Description:	Low toner.
Causes:	Toner is getting low. Defective Toner Sensor.

Error code:	049
Display:	Service Call 049: Error
Description:	CU type mismatch CU ROM does not match with the device.
Causes:	Is proper program ROM set?
Remedy:	Replace program ROM DIMM. Replace with proper program ROM DIMM.

Error code:	063
Display:	Service Call 063: Error
Description:	Network comm. Error Abnormal H/W I/F between CU-NIC.
Causes:	Is network board set properly? Is error recovered by replacing network board?
Remedy:	Set properly. Replace Network. Replace TIG board. (Replace EEPROM.)

Error code:	070
Display:	Service Call 070: Error
Description:	CANT_HAPPEN PS firmware fault detected.
Causes:	Confirm that error is recovered by turning power OFF/ON.
Remedy:	Replace TIG board. (Replace EEPROM.)

Error code:	072
Display:	Service Call 072: Error
Description:	Engine communication error I/F error between PU-CU.
Causes:	Is CU assembly set properly? Is error recovered by replacing TIG board?
Remedy:	Set properly. Replace TIG board. (Replace EEPROM.) Replace PU board.

Error code:	073
Display:	Reboot the printer. 073: Error xxxxxxxx
Description:	Video Error Error is detected when expanding the video data. (Illegal data is received.)
Remedy:	Is the CU assembly installed normally? Does this error recur? Re-install the CU assembly normally. Change the PC with another PC having high specifications, or alternately reduce resolution power and execute the print again. Replace the CU board. Replace the interface cable. Re-install the PC Printer driver. Is the CU assembly installed normally? Does this error recur? Does the error depend on print Data? Re-install the CU assembly normally. Execute the print again. Print any other data. Replace the CU board. Send the data to design division and request analysis of the data.

Error code:	074
Display:	POWER OFF/ON 074:Error xxxxxxxx 075:Error xxxxxxxx
Description:	F/W Overrun detect
Causes:	Is CU assembly set properly?

Error code:	075
Display:	Power off/on 075: Error
Description:	An error was detected during image data expansion.
Causes:	Is the CU/PU installed properly?
Remedy:	Does this error recur? Yes Cycle the power. Replace the CU/ PU board.

Error code:	081
Display:	Service Call 081: Error
Description:	Parameter Match Check Error
Remedy:	Normal Read/Write not possible with EEPROM or Flash. If the condition does not change replace CU PCB.

Error code:	104
Display:	Service Call 104: Error
Description:	Developer Motor Failure The Developer Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Developer Drive Assembly, PL8.1.1 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Developer Drive Assembly for damage. Are any parts of the Developer Drive Assembly damaged or excessively worn? Replace the Developer Drive Assy. Go to Step 2. 2 Check the Developer Motor connection. Is P/J491 connected to the harness? Go to Step 3. Reconnect the Developer Motor. 3 Test the Developer Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Developer Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Developer Motor. Is the +24 V across P/J491-1 <=> P/J 481-5? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J491. 2. Check continuity between J48 <=> J491. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness.