OKI C941

Рейтинг

Модули

Comsumable -2

Feeder-Assy

Board-Power-Sub-assy

Motor-Assy-JobOFF

Holder-Assy-soft SW

Hopping-Unit

Duplex-Unit

Plate-Assy-Retard

Plate-Base-Assy

Frame-Assy-TC

Frame-Assy-TC-R

Printer-NIP

Common

Contact-Assy

Plate-Assy-Side-RA

Motor-Assy-FAN

Cover-Assy-Front

Case-Cassette-Assy

LSD-Unit

Comsumable -1

Main-Frame-Assy

Plate-Assy-Front

Sensor-Assy-WT

EJ-Rail-Assy

MPT-Unit

Plate-Assy-Side-LB

Holde-Head-Assy

Plate-Assy-Rear

Printer-Unit-PX753

Детали

Деталь:	CLUTCH
Парткод:	45366007

Деталь:	PWR unit-ACDC Switch
Парткод:	44978701

Деталь:	Motor-Fan
Парткод:	45180201

Деталь:	Motor-Resist
Парткод:	42058201

Деталь:	OR-Board-F1W
Парткод:	45540901

Деталь:	Roller-Assy-Regist-T
Парткод:	45177801

Деталь:	PX753 F1T-1 maintenance board
Парткод:	45642404

Деталь:	OR-Board-F1K
Парткод:	45540401

Деталь:	Geard-Motor(Option)
Парткод:	42694602

Деталь:	Motor-Assy-Geard
Парткод:	45171801

Деталь:	Motor-Assy-Geard
Парткод:	45171801

Деталь:	LED Head Unit-63TRL
Парткод:	45538601

Деталь:	CASSETTE ASSY.
Парткод:	45180401

Деталь:	Eject-Assy-Joboff
Парткод:	45238101

Деталь:	Lever-Stacker-Full
Парткод:	45241001

Деталь:	Cover-Assy-OP-Panel
Парткод:	45247201

Деталь:	Sheet-OP-Panel
Парткод:	45247901

Деталь:	Duplex-Unit
Парткод:	45286301

Деталь:	OR-Board-AHV-5 colors
Парткод:	45392601

Деталь:	OR-Board-AHV-4 colors
Парткод:	45392602

Деталь:	F1D-1 maintenance board
Парткод:	45642402

Деталь:	F1D-2 maintenance board
Парткод:	45642403

Деталь:	maintenance board
Парткод:	45623706

Деталь:	maintenance board
Парткод:	45623707

Деталь:	maintenance board
Парткод:	45623708

Деталь:	OR-Board-F1X
Парткод:	45539901

Деталь:	Frame-Assy-TC-A (White Duct)
Парткод:	45519801

Деталь:	Frame-Assy-TC-A (Clear Duct)
Парткод:	45519802

Деталь:	OR-Board-F1G
Парткод:	45540601

Деталь:	OR-Board-AHR
Парткод:	45449201

Деталь:	OR-MFH
Парткод:	45169301

Деталь:	Motor-Fan
Парткод:	42781702

Деталь:	Filter-Front
Парткод:	45512901

Деталь:	Motor-FAN(60-15)
Парткод:	45516301

Деталь:	OR-Board-F1E
Парткод:	45541001

Деталь:	Guide Assy.-Tail
Парткод:	42717003

Деталь:	Gear-Assy-Oneway-Z33
Парткод:	45470301

Деталь:	Gear-Assy-Oneway-Z33-R
Парткод:	45470401

Деталь:	OR-Board-F1L
Парткод:	45540501

Деталь:	Hopping-Unit
Парткод:	45173501

Деталь:	Sensor-Assy-Front
Парткод:	45188301

Деталь:	Motor-Fan
Парткод:	45552101

Деталь:	OR-Board-F1N
Парткод:	45540101

Деталь:	Guide-Assy-Eject-Lower
Парткод:	45235201

Деталь:	Guide-Assy-Eject-Lower-SP
Парткод:	45235202

Деталь:	Decurl-Assy
Парткод:	45246501

Деталь:	Hopper-Assy
Парткод:	45220001

Деталь:	OR-Board-F1S
Парткод:	45540301

Деталь:	CONN-Assy-Fuser
Парткод:	45198401

Деталь:	Holder-Head-F
Парткод:	45206801

Деталь:	Holder-Head-R
Парткод:	45206901

Деталь:	Motor-Fan
Парткод:	45180202

Деталь:	Belt-Drive-Assy
Парткод:	45189701

Деталь:	Fuser-Drive-Assy
Парткод:	45192101

Деталь:	Motor Assy.-Regist
Парткод:	45192901

Деталь:	Read Write System Contact
Парткод:	45085901

Деталь:	Belt-Mini Pitch(B190)
Парткод:	42846706

Деталь:	Motor-Assy-ID
Парткод:	45207401

Деталь:	Motor-Assy-ID(K)
Парткод:	45207402

Деталь:	MPT-Unit
Парткод:	45218901

Деталь:	Roller-Assy-Regist-2
Парткод:	45228601

Деталь:	Roller-Assy-Synchro
Парткод:	45230601

Деталь:	Regist-Sensor-Assy_753
Парткод:	45231901

Деталь:	Guide-Assy-Eject-M
Парткод:	45233601

Деталь:	Guide-Assy-Eject-M-SP
Парткод:	45233602

Деталь:	Moto-FAN(60)
Парткод:	45516801

Деталь:	OR-Board-F1N
Парткод:	45540101

Деталь:	OR-Board-F1H
Парткод:	45540201

Коды ошибок

001

002, 003, 005

012

020

024

030

040

042, 043, 045

051

052

067

069

070

072

073

074, 075

077

081

104

106

108

111

112

113

114

115

121

123

124

125

126

128

134

135

143

147

163

166

167

168

169

170, 171

172, 173

181 ... 185

188

190

203, 204

207, 208

213, 214

230

231

241 ... 245

247

249

250

251

254

257

901, 902

903, 904

993

994

F0C

FFF

Описание

Парткод

Название

OKI Блок фотобарабана желтый

OKI Блок фотобарабана пурпурный

OKI Блок фотобарабана голубой

OKI Блок фотобарабана черный

OKI Блок фотобарабана белый

OKI Блок фотобарабана прозрачный

OKI Узел термозакрепления (печка)

OKI (45531213) Ремень переноса

OKI Комплект для печати белым плашечным цветом

OKI Комплект прозрачного плашечного цвета (набор глянцевый)

OKI Емкость для отработанного тонера

OKI Тонер-картридж желтый (24000 стр.)

OKI Тонер-картридж пурпурный (24000 стр.)

OKI Тонер-картридж голубой (24000 стр.)

OKI Тонер-картридж черный (24000 стр.)

OKI Тонер-картридж белый

OKI Тонер-картридж прозрачный

OKI Тонер-картридж желтый (38000 стр.)

OKI Тонер-картридж пурпурный (38000 стр.)

OKI Тонер-картридж голубой (38000 стр.)

OKI Тонер-картридж черный (38000 стр.)

Деталь:	Fuser-Unit-PX753-100V- Consumable
Парткод:	45531111

Деталь:	Fuser-Unit-PX753-120V- Consumable
Парткод:	45531112

Деталь:	Fuser-Unit-PX753-230V- Consumable
Парткод:	45531113
Цена:	24 800 ₽

Деталь:	Box-Waste-Toner- PX753(ODA)
Парткод:	45531502

Error code:	001
Display:	Service Call 001: Error
Description:	Leading edge of the recording paper fails to reach the Timing Sensor. (1st Cassette)
Causes:	Recording paper jam. Timing Sensor abnormal.
Remedy:	Is the error display reproducible? Power OFF/ON Replace CU PCB. (Must replace EEPROM)

Error code:	012
Display:	Power Off/On 012:Error
Description:	The length of the received document is over 2 meter (78.7in).
Remedy:	Does this error message reappear? Yes Power OFF/ON. Replace the printer control PCB.

Error code:	020
Display:	Service Call 020: Error
Description:	CU ROM Hash Check Error 1
Causes:	Is program ROM DIMM set properly? Is error recovered by replacing program ROM DIMM?
Remedy:	Reset program ROM DIMM. Replace program ROM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	024
Display:	Service Call 024:Error
Description:	CU Font ROM Hash Error
Causes:	Does this error message reappear?
Remedy:	Does this error message reappear? Yes Power OFF/ON. Replace the printer control PCB.

Error code:	030
Display:	Service Call 030: Error
Description:	CU Slot1 DIMM RAM Check Error
Causes:	Is subject RAM DIMM set properly? Is error recovered by replacing subject ROM DIMM?
Remedy:	Reset subject RAM DIMM. Replace RAM DIMM. Replace TIG board. (Replace EEPROM)

Error code:	040
Display:	Service Call 040: Error
Description:	CU EEPROM Error
Causes:	Is error recovered by replacing EEPROM on CU board?
Remedy:	Replace EEPROM. (Recover user environment.) Replace TIG board. (Replace EEPROM)

Деталь:	Belt-Unit-PX753(ODA)
Парткод:	45531212

Error code:	051
Display:	Service Call 051: Error
Description:	CU Fan Error Abnormal CPU cooling fan on CU board.
Causes:	Is connector set properly on CU board? Is error recovered by replacing fan?
Remedy:	Connect properly. Replace fan. Replace TIG board. (Replace EEPROM.)

Error code:	052
Display:	Power Off/on 052: Error
Description:	Image Processor Driver Error
Causes:	Does this error message reappear?
Remedy:	Is the error display reproducible? Power OFF/ON Replace CU PCB. (Replace EEPROM)

Error code:	067
Display:	Service Call 067:Error
Description:	A communication error was detected during communication with the Sleep Mode interface monitoring program.
Causes:	Does this error recur?
Remedy:	A communication error was detected during communication with the Sleep Mode interface monitoring program. If power cycling does not solve the problem, maintenance by a service engineer is required.

Error code:	069
Display:	Service Call 069:Error
Description:	Malfunction of the NIC chip was detected.
Causes:	Does this error recur?
Remedy:	Does this error recur? Yes Power OFF/ON. Replace the printer control PCB.

Error code:	070
Display:	Service Call 070: Error
Description:	CANT_HAPPEN PS firmware fault detected.
Causes:	Confirm that error is recovered by turning power OFF/ON.
Remedy:	Replace TIG board. (Replace EEPROM.)

Error code:	072
Display:	Service Call 072: Error
Description:	Engine communication error I/F error between PU-CU.
Causes:	Is CU assembly set properly? Is error recovered by replacing TIG board?
Remedy:	Set properly. Replace TIG board. (Replace EEPROM.) Replace PU board.

Error code:	073
Display:	Reboot the printer. 073: Error xxxxxxxx
Description:	Video Error Error is detected when expanding the video data. (Illegal data is received.)
Remedy:	Is the CU assembly installed normally? Does this error recur? Re-install the CU assembly normally. Change the PC with another PC having high specifications, or alternately reduce resolution power and execute the print again. Replace the CU board. Replace the interface cable. Re-install the PC Printer driver. Is the CU assembly installed normally? Does this error recur? Does the error depend on print Data? Re-install the CU assembly normally. Execute the print again. Print any other data. Replace the CU board. Send the data to design division and request analysis of the data.

Error code:	077
Display:	Power Off/On 077:Error xx
Description:	Detected of abnormal condition during image data expansion
Causes:	Does this error recur?
Remedy:	Does this recur? Yes Power OFF/ON. Replace the printer control PCB

Error code:	081
Display:	Service Call 081: Error
Description:	Parameter Match Check Error
Remedy:	Normal Read/Write not possible with EEPROM or Flash. If the condition does not change replace CU PCB.

Error code:	104
Display:	Service Call 104: Error
Description:	Developer Motor Failure The Developer Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Developer Drive Assembly, PL8.1.1 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Developer Drive Assembly for damage. Are any parts of the Developer Drive Assembly damaged or excessively worn? Replace the Developer Drive Assy. Go to Step 2. 2 Check the Developer Motor connection. Is P/J491 connected to the harness? Go to Step 3. Reconnect the Developer Motor. 3 Test the Developer Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Developer Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Developer Motor. Is the +24 V across P/J491-1 <=> P/J 481-5? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J491. 2. Check continuity between J48 <=> J491. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness.

OKI C941

Модули

Детали

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	106
Display:	Service Call 106: Error
Description:	Motor Failure One of the primary drive motors has failed.
Causes:	• Main Drive Assembly, PL8.1.2 • Developer Drive Assembly, PL8.1.1 • Fuser Drive Assembly, PL5.2.25 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11
Remedy:	1 Check the motors. Run the Service Diagnostics motor tests to determine the failed part. Is the failed part the Main Drive Motor? Go to. Test the Fuser Motor. 2 Is the failed part the Fuser Drive Motor? Go to. Test the Developer Motor. 3 Is the failed part the Developer Drive Motor? Go to. Replace the Engine Control Board.

Error code:	108
Display:	Service Call 108:Error
Description:	Printhead Error
Remedy:	Yellow printhead lost Hsync Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J7 and J8 on the system board. Go to “System board” If the cables are connected correctly to the system board and to the printhead assembly, replace the “Printhead diagnostics”. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics”

Error code:	111
Display:	SVC 111 ERROR
Description:	Printhead Error
Causes:	Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization
Remedy:	No first Hysnc - magenta Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J11 and J12 on the system board. Go to “System board”. If the cables are connected correctly to the system board and to the printhead assembly, go to “Printhead diagnostics”

Error code:	112
Display:	SVC 112 ERROR
Description:	Printhead Error
Causes:	Incorrect color DTM installation, incorrect PCU installation, development bias error, MCU, LD control malfunction, loss of synchronization
Remedy:	No first Hysnc - yellow Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J7 and J8 on the system board. Go to “System board”. If the cables are connected correctly to the system board and to the printhead assembly, go to “Printhead diagnostics”. Note: Do not adjust or replace any printhead before performing checks in “Printhead diagnostics”

Error code:	113
Display:	SVC 113 ERROR
Description:	Finisher Stapler Failure, Code 113 The staple home sensor doesn’t turn ON within 2 seconds after the stapler motor started to turn backwards.
Causes:	• Finisher Control Board • Staple Unit Assembly
Remedy:	1 1. Enter service diagnostics. 2. Run the Stapler Home sensor test. 3. Does the value change from H to L when the stapler is moved away from the home position? Go to step 6. Go to step 2. 2 1. Measure the voltage between finisher board connector P852-2 and frame ground. 2. Does the voltage change between 0 and +5 VDC when the sensor is blocked and unblocked? Replace the finisher control board. Go to step 3. 3 1. Measure the voltage at the Finisher Board connector P852-1. 2. Dose the voltage measure +5 VDC? The home sensor or the wiring is bad. Replace the staple unit assembly. Go to step 4. 4 1. Disconnect the Stapler Unit Assembly. 2. Measure the voltage between the finisher board connector P852-1 and frame ground. 3. Does the voltage measure +5 VDC? Replace the stapler unit assembly. Go to step 5. 5 Is +24 VDC present at either J847-7 or J847-9? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. 6 1. Enter service diagnostics and run the “Stapler Close Motor” test. 2. Does the stapler motor operate correctly? Replace the finisher control board. Go to step 7. 7 With the Stapler Close Motor test running is +24 VDC present at J847-7? Replace in the following order: • stapler head assembly • finisher control board Troubleshoot and repair the +24 VDC interlock circuit.

Error code:	114
Display:	Service Call 114:Error
Description:	Front Tamper Home Sensor Failure, Code 114 With the Front Tamper Home Sensor OFF the Front Tamper Home Sensor did not turn ON within 800 ms after the move to the Front Tamper Home position has begun. With the Front Tamper Home Sensor on the Front Tamper Sensor did not turn Off when the Front Tamper Home Sensor is deactuated.
Causes:	• Front Tamper Motor • Finisher Control Board
Remedy:	1 1. Run the Front Tamper Low Front or Front Tamper Low Rear test in diagnostics. 2. Does the front tamper guide operate? Go to step 6. Go to step 2. 2 Does the front tamper motor operate? Check the tampering mechanism for a mechanical problem. Go to step 3. 3 1. Check pins J877 A pins 1,3,4 and 6. 2. Is +24 VDC present on any of the pins? Go to step 4. Go to step 5. 4 1. Check the following wires for and open circuit or short circuit to ground. Is any wire open or shorted? J877A-1 to J848B-7 J877A-3 to J848B-9 J877A-4 to J848B-10 J877A-6 to J848B-12 Repair or replace the wiring harness. Replace in order until resolved: • front tamper motor • finisher control board 5 Is +24 VDC present on pins J848B-8 and J848B-11 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. 6 1. Check the tamper front home sensor in diagnostics. 2. Does the value change from H to L when the tamper is moved away from the home position? Replace the finisher control board. Repair the sensor using the Transmissive Sensor troubleshooting procedure.

Error code:	115
Display:	Service Call 115:Error
Description:	Rear Tamper Home Sensor Failure, Code 115 With the Rear Tamper Home Sensor OFF the Rear Tamper Home Sensor did not turn On within 800 ms after the move to the Rear Tamper Home position has begun. With the Rear Tamper Home Sensor on the Rear Tamper Sensor did not turn Off when the Rear Tamper Home Sensor is deactuated.
Causes:	• Rear Tamper Motor • Finisher Control Board
Remedy:	1 1. Run the Rear Tamper Low Front or Rear Tamper Low Rear test in diagnostics. 2. Does the rear tamper guide operate? Go to step 6. Go to step 2. 2 Does the rear tamper motor operate? Check the tampering mechanism for a mechanical problem. Go to step 3. 3 1. Check pins J878A pins 1,3,4 and 6. 2. Is +24 VDC present on any of the pins? Go to step 4. Go to step 5. 4 1. Check the following wires for and open circuit or short circuit to ground. 2. Is any wire open or shorted? 3. J878A-1 to J848B-1 4. J878A-3 to J848B-3 5. J878A-4 to J848B-4 6. J878A-6 to J848B-6 Repair or replace the wiring harness. Replace in order until resolved: • rear tamper motor • finisher control board 5 Is +24 VDC present on pins J848B-2 and J848B-5 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. 6 1. Check the tamper rear home sensor in diagnostics. 2. Does the value change from H to L when the tamper is moved away from the home position? Replace the finisher control board. Repair the sensor circuit using the transmissive sensor troubleshooting procedure.

Error code:	121
Display:	Service Call 121: Error
Description:	Fuser Error
Causes:	Is cable between PU board andhighvoltage power LSI connected properly?
Remedy:	Wrong fuser lamp - BUR - replace the fuser assembly

Error code:	123
Display:	Service Call 123: Error
Description:	Finisher Set Clamp Failure, Code 123 The set clamp home sensor did not turn on within 2 seconds after the set clamp started operation.
Causes:	• Set Clamp Solenoid • Finisher Control Board
Remedy:	1 1. Check the Set Clamp home sensor in diagnostics. 2. Does the value change from H to L while rotating the actuator? Go to step 2. Use the transmissive Sensor procedure to diagnose and repair the sensor. 2 Does the solenoid energize when running the Set Clamp Paddle test in diagnostics? Go to step 3. Go to step 4. 3 1. Run the Eject Forward Test and then the Eject Release Test in diagnostics. 2. Does the set clamp paddle turn once? Replace the finisher control board. Go to step 4. 4 Is +24 VDC present at P848A-10? Go to step 5. Go to step 6. 5 Is +24 VDC present at P848A-11? Replace the finisher control board. Replace the set clamp solenoid. 6 Is +24 VDC present at test point 9 on the finisher control board? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit.

Error code:	124
Display:	Service Call 124: Error
Description:	Finisher Communication Failure, Code 124
Remedy:	There are no diagnostic routines for problems involving serial communications. It is recommended that you address the following assemblies in this order: • Finisher Control Board • Engine Control Board • Perform continuity checks on any wiring harnesses involved.