Ricoh Aficio Color 5560
Рейтинг
Модули
Opetation Panel
TRANSFER BELT UNIT 3
Used Tonner Section 2
PAPER REGISTRATION 2
ARDF Exterior
ELECTRICAL SECTION 3
Drive Section 5
ARDF Drive & Electrical 2
Paper Transfer 2
ELECTRICAL SECTION 7
OPTICS SECTION 1
DUPLEX UNIT 3
ARDF Frame
FUSING UNIT 1
By-pass Feed 2
ARDF Drive & Electrical 1
VERTICAL TRANSPORT
Tonner Supply 3
Used Tonner Section 1
Paper Exit 3
OPTICS SECTION 3
DRIVE SECTION 3
DUPLEX UNIT 1
Original Exit 2
ELECTRICAL SECTION 6
Universal Tray 2
TANDEM TRAY 2
Paper Exit 2
OPTICS SECTION 4
FUSING UNIT 3
PAPER REGISTRATION 1
TANDEM TRAY 1
ELECTRICAL SECTION 2
Original Trans 1
EXTERIOR 1
Transfer Belt Cleaning
EXTERIOR 2
FRAME SECTION 1
FUSING UNIT 2
Tonner Supply 2
Tonner Supply 1
Transfer Cover
Fusing Unit 4
ELECTRICAL SECTION 4
Transfer Entrance 1
DUPLEX UNIT 2
Original Feed 2
PCU 2
Paper Transfer 1
Paper Exit 1
Drive Section 1
Transfer Entrance 3
Paper Exit 4
Frame Section 4
ELECTRICAL SECTION 8
DEVELOPMENT UNIT
By-pass Feed 1
LASER UNIT
Original Exit 1
PCU 1
Transfer Entrance 2
Original Feed 1
TRANSFER BELT UNIT 2
ELECTRICAL SECTION 5
ARDF Original Tray
TANDEM TRAY 3
Original Trans 2
DUPLEX UNIT 4
ELECTRICAL SECTION 1
Universal Tray 1
FRAME SECTION 2
DRIVE SECTION 2
DRIVE SECTION 4
DUPLEX UNIT 5
Original Trans 3
OPTICS SECTION 2
Frame Section 3
TRANSFER BELT UNIT 1
Детали ARDF Frame
| Деталь: | Operation Panel (NA) |
| Парткод: | B132 7212 |
| Деталь: | Operation Panel (EU) |
| Парткод: | B132 7213 |
| Деталь: | Keytop:Application:Job (NA) |
| Парткод: | B132 7331 |
| Деталь: | Keytop+O8176:Job (EU) |
| Парткод: | B132 7341 |
| Деталь: | Keytop:Application:Copy (NA) |
| Парткод: | B132 7332 |
| Деталь: | Keytop:Application:Copy (EU) |
| Парткод: | B132 7342 |
| Деталь: | Keytop:Application:Doc (NA) |
| Парткод: | B132 7333 |
| Деталь: | Keytop:Application:Doc (EU) |
| Парткод: | B132 7343 |
| Деталь: | Keytop:Application:Base |
| Парткод: | B132 7273 |
| Деталь: | Keytop:Application:Cover |
| Парткод: | B132 7274 |
| Деталь: | Keytop:Scanner:NA (B181) |
| Парткод: | B737 7219 |
| Деталь: | Keytop:Scanner:EU (B181) |
| Парткод: | B737 7229 |
| Деталь: | Keytop:Printer:NA (B181) |
| Парткод: | B737 7218 |
| Деталь: | Keytop:Printer:EU (B181) |
| Парткод: | B737 7228 |
| Деталь: | Decal - Inkjet:Paper |
| Парткод: | B132 1562 |
| Деталь: | Lens:Data:In |
| Парткод: | B132 7276 |
| Деталь: | DIAL |
| Парткод: | B027 1444 |
| Деталь: | Keytop:Counter |
| Парткод: | B132 7263 |
| Деталь: | Lens:Keytop:1 |
| Парткод: | B132 7275 |
| Деталь: | Keytop:Collar Adjust |
| Парткод: | B132 7262 |
| Деталь: | Keytop:Confirm |
| Парткод: | B132 7261 |
| Деталь: | Keytop:Block Diagram |
| Парткод: | B132 7260 |
| Деталь: | Keytop:Clear:Modes |
| Парткод: | B132 7349 |
| Деталь: | Keytop:Preheat |
| Парткод: | B132 7258 |
| Деталь: | Keytop: Interrupt |
| Парткод: | B132 7257 |
| Деталь: | Keytop:10key |
| Парткод: | B132 7252 |
| Деталь: | Keytop:Clear/Stop |
| Парткод: | B132 7254 |
| Деталь: | Keytop:Start |
| Парткод: | B132 7265 |
| Деталь: | Keytop:Sample Copy |
| Парткод: | B132 7253 |
| Деталь: | Keytop:Power Source |
| Парткод: | B132 7256 |
| Деталь: | PCB:OP-L |
| Парткод: | B132 7310 |
| Деталь: | PCB:OP-R |
| Парткод: | B132 7300 |
| Деталь: | Shadeing Plate:Touch Panel |
| Парткод: | B132 7286 |
| Деталь: | Insulating Sheet:LCD:Touch Panel |
| Парткод: | B132 7297 |
| Деталь: | Touch Panel:HVGA |
| Парткод: | B180 5258 |
| Деталь: | Long Spacer - Touch Panel |
| Парткод: | B027 1484 |
| Деталь: | Short Spacer - Touch Panel |
| Парткод: | B027 1485 |
| Деталь: | LCD:H-VGA:EDMGU95WDF:BK |
| Парткод: | B140 7510 |
| Деталь: | Bracket:LCDC:Assy |
| Парткод: | B132 7282 |
| Деталь: | Bracket:OP-R |
| Парткод: | B132 7290 |
| Деталь: | Clamp:LWS-05S |
| Парткод: | B132 7296 |
| Деталь: | PCB:OPU (NA) |
| Парткод: | B132 5194 |
| Деталь: | PCB:OPU (EU) |
| Парткод: | B132 5195 |
| Деталь: | Harness:OP-L:15 |
| Парткод: | B132 7314 |
| Деталь: | Harness:OP-L:14 |
| Парткод: | B132 7313 |
| Деталь: | Harness - SDG OP-R 13 |
| Парткод: | B104 5083 |
| Деталь: | Harness - SDG OP-R 10 |
| Парткод: | B104 5084 |
| Деталь: | Bracket:Coupling:Machine or Cop |
| Парткод: | B132 7287 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Keytop:Round:Coupling |
| Парткод: | B132 7266 |
| Деталь: | Power Pack:T1/T2 |
| Парткод: | AZ32 0138 |
| Деталь: | Insulating Sheet:Power Pack |
| Парткод: | B132 6145 |
| Деталь: | Guard:Right |
| Парткод: | B132 6170 |
| Деталь: | Guard:Left |
| Парткод: | B132 6171 |
| Деталь: | Guard:Rear |
| Парткод: | B132 6172 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Spring Plate:Cam |
| Парткод: | B132 6124 |
| Деталь: | Stopper:On-Off |
| Парткод: | B132 6157 |
| Деталь: | DUCT |
| Парткод: | B132 6121 |
| Деталь: | Harness:Density Sensor |
| Парткод: | B132 5237 |
| Деталь: | Belt Sensor |
| Парткод: | B132 6119 |
| Деталь: | Bracket:Belt Sensor |
| Парткод: | B132 6122 |
| Деталь: | Stand |
| Парткод: | B132 6156 |
| Деталь: | Harness:Intermediate Transfer:39pin |
| Парткод: | B132 5376 |
| Деталь: | Harness:Intermediate Transfer:18pin |
| Парткод: | B132 5377 |
| Деталь: | Harness:Transfer Unit:Belt Cleaning |
| Парткод: | B132 5355 |
| Деталь: | Plate:Bracke |
| Парткод: | B132 6165 |
| Деталь: | Grip:Application |
| Парткод: | B712 5605 |
| Деталь: | Duct:Side Plate:Rear:Front:Assy |
| Парткод: | B132 2443 |
| Деталь: | Toner Outlet Sub-unit:Cover:PCU |
| Парткод: | B132 6572 |
| Деталь: | Transport Screw:Side |
| Парткод: | B132 6556 |
| Деталь: | Toner Outlet Sub-unit |
| Парткод: | B132 6570 |
| Деталь: | Gear:29Z |
| Парткод: | B132 6592 |
| Деталь: | Gear:25Z |
| Парткод: | AB01 0135 |
| Деталь: | Holder:Drive Sub-unit |
| Парткод: | B132 1316 |
| Деталь: | Shaft:Horizontal:Assy |
| Парткод: | B132 1311 |
| Деталь: | Holder:Drive Sub-unit |
| Парткод: | B1321320 |
| Деталь: | Flange:Timing Pulley |
| Парткод: | B132 1312 |
| Деталь: | Timing Belt:40S2M308 |
| Парткод: | AA04 3300 |
| Деталь: | Timing Pulley:30T |
| Парткод: | AB03 0300 |
| Деталь: | Shaft:Drive:Diagonal,slanted:Assy |
| Парткод: | B132 1315 |
| Деталь: | Gear:30Z |
| Парткод: | AB01 3189 |
| Деталь: | Gear:26Z |
| Парткод: | AB01 3122 |
| Деталь: | Case:Drive:Assy |
| Парткод: | B132 6540 |
| Деталь: | Shaft:Drive:Short:Assy |
| Парткод: | B132 6545 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Transport Screw:Lengthwise |
| Парткод: | B132 6561 |
| Деталь: | PIPE |
| Парткод: | B132 6531 |
| Деталь: | Duct:Connecting:Pull Out |
| Парткод: | B132 2462 |
| Деталь: | Cover:Drawer |
| Парткод: | B1321229 |
| Деталь: | Toner Catchpan:CM |
| Парткод: | B132 6597 |
| Деталь: | Toner Catchpan:K |
| Парткод: | B132 6599 |
| Деталь: | Arm:Tightener |
| Парткод: | B1321325 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0160 |
| Деталь: | Screw:DIA4:M3 |
| Парткод: | AA14 3550 |
| Деталь: | Toner Outlet Sub-unit:Assy |
| Парткод: | B132 6533 |
| Деталь: | GUIDE PLATE |
| Парткод: | B065 6372 |
| Деталь: | Transport Roller |
| Парткод: | AF02 2149 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0327 |
| Деталь: | Driven Shaft |
| Парткод: | AA14 0829 |
| Деталь: | Transport Roller Lever |
| Парткод: | B065 6453 |
| Деталь: | Screw - Scale |
| Парткод: | AA14 3812 |
| Деталь: | Driven Release Lever |
| Парткод: | B065 6454 |
| Деталь: | Driven Pressure Lever |
| Парткод: | B065 6455 |
| Деталь: | Front Side Plate - Paper Feed |
| Парткод: | B065 6336 |
| Деталь: | Support Guide Plate |
| Парткод: | B065 6371 |
| Деталь: | Relay Shaft |
| Парткод: | B065 6317 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1469 |
| Деталь: | Rear Side Plate - Paper Feed |
| Парткод: | B065 6330 |
| Деталь: | Gear - 18Z |
| Парткод: | AB01 1470 |
| Деталь: | Tray Link Guide |
| Парткод: | B065 6452 |
| Деталь: | Paper Tray Link |
| Парткод: | B065 6346 |
| Деталь: | Arm Screw |
| Парткод: | 58 942 540 |
| Деталь: | SPRING |
| Парткод: | AA06 0900 |
| Деталь: | Pulley:Idler:30t/24z |
| Парткод: | AB01 7690 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3575 |
| Деталь: | Vertical Transport Link |
| Парткод: | B065 6456 |
| Деталь: | SPRING |
| Парткод: | AA06 0901 |
| Деталь: | Ground Plate:Stepper Motor:Paper Fe |
| Парткод: | B140 6378 |
| Деталь: | Stepper Motor:Paper Feed Unit:Assy |
| Парткод: | B132 6655 |
| Деталь: | MOTOR BRACKET |
| Парткод: | B065 6394 |
| Деталь: | SPRING |
| Парткод: | AA06 0904 |
| Деталь: | Motor Base |
| Парткод: | B065 6415 |
| Деталь: | Pulley - 20T |
| Парткод: | AB03 0733 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3576 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2080 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A294 6700 |
| Деталь: | Reverse Driven Shaft |
| Парткод: | B065 6307 |
| Деталь: | Driven Reverse Gear - 21Z |
| Парткод: | AB01 1391 |
| Деталь: | Reverse Gear |
| Парткод: | AB01 1471 |
| Деталь: | Reverse Drive Shaft |
| Парткод: | B065 6306 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 1491 |
| Деталь: | Gear - 38Z |
| Парткод: | AB01 1490 |
| Деталь: | Pulley - 30Z |
| Парткод: | AB03 0734 |
| Деталь: | Ground Plate:Reverse:Paper Feed Unit |
| Парткод: | B140 6377 |
| Деталь: | DC Solenoid:Reverse:Assy |
| Парткод: | B132 6670 |
| Деталь: | ADF:Assy |
| Парткод: | B132 7451 |
| Деталь: | Cover:Front |
| Парткод: | B652 1902 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Cover:Rear |
| Парткод: | B652 1952 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Stopper:Guide Plate:Pressure Plate |
| Парткод: | B652 4903 |
| Деталь: | Pressure Plate Tape |
| Парткод: | B477 2715 |
| Деталь: | Pressure Plate:Assy |
| Парткод: | B652 4741 |
| Деталь: | Guide Plate:Pressure Plate |
| Парткод: | B652 4902 |
| Деталь: | MAGNET |
| Парткод: | G012 1 531 |
| Деталь: | Decal:Misfeed Removal |
| Парткод: | B652 4905 |
| Деталь: | STEPPED SCREW |
| Парткод: | A859 7211 |
| Деталь: | Decal:Misfeed Removal |
| Парткод: | B652 1906 |
| Деталь: | Decal:Misfeed Removal:Exit |
| Парткод: | B6521905 |
| Деталь: | Hinge:C/T Box:Upper |
| Парткод: | B132 5933 |
| Деталь: | Hinge:C/T Box:Lower |
| Парткод: | B132 5930 |
| Деталь: | Bracket:Guard:Harness |
| Парткод: | B132 1113 |
| Деталь: | Fan Motor MM80 |
| Парткод: | AX64 0159 |
| Деталь: | Bracket:Fan Motor |
| Парткод: | B132 5944 |
| Деталь: | Seal:C/T Box:Upper:Side |
| Парткод: | B132 5813 |
| Деталь: | Bracket:C/T Box:Right Upper |
| Парткод: | B132 5941 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3718 |
| Деталь: | Stopper:C/T Box:Upper |
| Парткод: | B132 5989 |
| Деталь: | Bracket:C/T Box:Upper |
| Парткод: | B132 5940 |
| Деталь: | Grip:Application |
| Парткод: | B712 5605 |
| Деталь: | Large Drum Stay Ground Plate |
| Парткод: | B070 6877 |
| Деталь: | GROUNDING PLATE |
| Парткод: | A267 7586 |
| Деталь: | Bracket: Interface:Fix:Auxiliary |
| Парткод: | B132 5965 |
| Деталь: | Ground Plate:Base:Control Board |
| Парткод: | B132 5807 |
| Деталь: | Bracket: Interface |
| Парткод: | B132 5963 |
| Деталь: | Arm:Hinge:C/T Box |
| Парткод: | B132 5947 |
| Деталь: | Bracket:Connector:Right |
| Парткод: | B132 6764 |
| Деталь: | Harness:Bank:Rear:3way |
| Парткод: | B132 5396 |
| Деталь: | Connector Spring |
| Парткод: | AA06 3268 |
| Деталь: | Bracket:Arm:Assy |
| Парткод: | B132 6726 |
| Деталь: | Bracket:Connector:Left |
| Парткод: | B132 6763 |
| Деталь: | LOCK ARM |
| Парткод: | B065 6769 |
| Деталь: | Spring - Large |
| Парткод: | AA06 2251 |
| Деталь: | DC Motor:Rise:Tandem LCT:Assy |
| Парткод: | B132 6759 |
| Деталь: | Spring - Small |
| Парткод: | AA06 2252 |
| Деталь: | DC Solenoid:Coupling:Assy |
| Парткод: | B132 6762 |
| Деталь: | DC Solenoid:Lock:Assy |
| Парткод: | B132 6765 |
| Деталь: | Spring:Connector:Tandem LCT |
| Парткод: | AA06 3902 |
| Деталь: | Spacer - 6mm |
| Парткод: | AA13 2203 |
| Деталь: | INTERFACE HARNESS |
| Парткод: | B477 5751 |
| Деталь: | Harness: Motor: Exit |
| Парткод: | B652 5421 |
| Деталь: | Harness:Solenoid:Reverse |
| Парткод: | B652 5426 |
| Деталь: | Harness:Paper Size Sensor |
| Парткод: | B652 5406 |
| Деталь: | Harness:Original Sensor |
| Парткод: | B652 5401 |
| Деталь: | Harness:Motor:Pick Up |
| Парткод: | B652 5441 |
| Деталь: | Paper Feed Motor Harness |
| Парткод: | B477 5691 |
| Деталь: | PCB:Main Control |
| Парткод: | B652 5501 |
| Деталь: | Stepper Motor:Base:Rise:Assy |
| Парткод: | B652 2911 |
| Деталь: | Bracket:Motor:Base:Assy |
| Парткод: | B652 2343 |
| Деталь: | Timing Belt:B40S2M158 |
| Парткод: | B652 2347 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A806 2287 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A806 2285 |
| Деталь: | Spacer - 8x20x1 |
| Парткод: | AA132152 |
| Деталь: | Timing Pulley - T30/Z20 S2M/M0.8 |
| Парткод: | A806 2161 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A806 2283 |
| Деталь: | Stepper Motor:Exit:Assy |
| Парткод: | B652 4722 |
| Деталь: | Timing Belt:B40S2M138 |
| Парткод: | B652 4728 |
| Деталь: | Scanning Motor- DC 7.4W |
| Парткод: | B477 3721 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B652 3211 |
| Деталь: | Tension Spring:Tension:Transport |
| Парткод: | AA06 0991 |
| Деталь: | Guide Plate:Stepper Motor |
| Парткод: | B652 3215 |
| Деталь: | Timing Belt:B60S2M280 |
| Парткод: | B652 1721 |
| Деталь: | Timing Belt:B40S2M230 |
| Парткод: | B652 4153 |
| Деталь: | Bracket:Solenoid:Reverse:Upper |
| Парткод: | B652 4223 |
| Деталь: | Damper - Junction Gate Solenoid |
| Парткод: | A697 2102 |
| Деталь: | DC Solenoid:Assy |
| Парткод: | B652 4222 |
| Деталь: | Bracket:Shaft:Scanning:Assy |
| Парткод: | B652 1781 |
| Деталь: | PULLEY |
| Парткод: | B477 3217 |
| Деталь: | Screw: Safety |
| Парткод: | AA14 3791 |
| Деталь: | PULLEY |
| Парткод: | B477 3175 |
| Деталь: | TENSION SPRING |
| Парткод: | B652 3174 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Belt Tensioner:Assy |
| Парткод: | B652 3231 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Transport Unit:Assy |
| Парткод: | B132 3850 |
| Деталь: | Transport Belt |
| Парткод: | AA04 0033 |
| Деталь: | Transport Roller:Driven |
| Парткод: | AF02 2064 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Transport Roller:Drive |
| Парткод: | B132 3851 |
| Деталь: | Supporting Plate:Vacuum |
| Парткод: | B132 3862 |
| Деталь: | Fan Motor MM60/15mm:24V |
| Парткод: | AX64 0158 |
| Деталь: | Harness:Transport Belt:Fan |
| Парткод: | B132 5248 |
| Деталь: | Collection Coil:Toner:Assy |
| Парткод: | B132 6260 |
| Деталь: | Tray:Toner Catchpan:Assy |
| Парткод: | B132 6257 |
| Деталь: | Stay:Pull Out |
| Парткод: | B132 6304 |
| Деталь: | Gear:30T |
| Парткод: | AB01 7338 |
| Деталь: | Timing Belt:S2M208 |
| Парткод: | AA04 3578 |
| Деталь: | Pulley:31T |
| Парткод: | AB03 0275 |
| Деталь: | Stopper:Transfer/Separation Unit |
| Парткод: | B132 6286 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Pulley:40T |
| Парткод: | AB03 0748 |
| Деталь: | Holder:Heater |
| Парткод: | B132 6507 |
| Деталь: | Heat Sink:Heater:Toner |
| Парткод: | B132 6506 |
| Деталь: | Heater:115V:18W:Upper |
| Парткод: | AX40 0176 |
| Деталь: | Heater:240V:18W:Upper |
| Парткод: | AX40 0178 |
| Деталь: | Cover:Heater |
| Парткод: | B132 6508 |
| Деталь: | Toner Hopper Shield |
| Парткод: | AA15 3448 |
| Деталь: | Bracket: LCT |
| Парткод: | B132 5866 |
| Деталь: | Shield:Exhaust |
| Парткод: | B132 2438 |
| Деталь: | Seal:Duct:Exhaust:Rear |
| Парткод: | B132 2478 |
| Деталь: | Duct:Exhaust:Rear |
| Парткод: | B132 2425 |
| Деталь: | Fan Motor:Sirocco |
| Парткод: | AX65 0041 |
| Деталь: | Stay:Sirocco |
| Парткод: | B132 2429 |
| Деталь: | Bracket:Stay:Sirocco |
| Парткод: | B132 2430 |
| Деталь: | OZONE FILTER |
| Парткод: | B132 2436 |
| Деталь: | DUST FILTER |
| Парткод: | B132 2435 |
| Деталь: | Shield:Filter |
| Парткод: | B132 2439 |
| Деталь: | Cover:Filter |
| Парткод: | B132 2437 |
| Деталь: | Bracket:Finishing Sub-unit |
| Парткод: | B132 5867 |
| Деталь: | Harness:AC Drive Board |
| Парткод: | B132 5380 |
| Деталь: | Duct:Exit:Exhaust:Exit |
| Парткод: | B132 6860 |
| Деталь: | Bracket:Duplex:Exhaust:Front |
| Парткод: | B132 6950 |
| Деталь: | Fan Motor:Upper:Assy |
| Парткод: | B132 6954 |
| Деталь: | Fan Motor:Lower:Assy |
| Парткод: | B132 6951 |
| Деталь: | Cover:Left Upper |
| Парткод: | B1321503 |
| Деталь: | Screw: M4:DIA5 |
| Парткод: | AA14 3559 |
| Деталь: | Exposure Glass:Sheet Through |
| Парткод: | BC01 2007 |
| Деталь: | SEAL |
| Парткод: | B065 1782 |
| Деталь: | Scale Bracket |
| Парткод: | B065 1787 |
| Деталь: | Scale Bracket Seal |
| Парткод: | B065 1773 |
| Деталь: | Bracket: Filter: Assy |
| Парткод: | B132 1856 |
| Деталь: | Filter: Scanner |
| Парткод: | B132 1864 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Left Scale |
| Парткод: | B065 1772 |
| Деталь: | Scale:Sheet Through (NA) |
| Парткод: | B1321687 |
| Деталь: | Scale:Sheet Through:Assy (EU) |
| Парткод: | B132 1686 |
| Деталь: | Exposure Glass |
| Парткод: | A2501752 |
| Деталь: | Scale:Rear:Printing |
| Парткод: | B132 1692 |
| Деталь: | Bracket:ADF |
| Парткод: | B1321885 |
| Деталь: | Decal - Copy:Original |
| Парткод: | B132 1583 |
| Деталь: | Cover:Right Upper |
| Парткод: | B132 1502 |
| Деталь: | RIGHT STAY |
| Парткод: | B065 1785 |
| Деталь: | Spring Plate:Ground Plate:ADF |
| Парткод: | B1321898 |
| Деталь: | Mylar:Frame:Front |
| Парткод: | B1321683 |
| Деталь: | Mylar:Frame:Middle |
| Парткод: | B132 1684 |
| Деталь: | Mylar:Frame:Rear |
| Парткод: | B1321685 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54 421 924 |
| Деталь: | Cushion - 0.5 |
| Парткод: | AA16 1137 |
| Деталь: | Stepper Motor:Reverse:Assy |
| Парткод: | B132 4780 |
| Деталь: | Bracket:Motor:Reverse:Assy |
| Парткод: | B132 4810 |
| Деталь: | Gear:22/24Z |
| Парткод: | AB01 7687 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3291 |
| Деталь: | DC Solenoid:Reversal:Assy |
| Парткод: | B132 4745 |
| Деталь: | Stepper Motor:Jogger:Assy |
| Парткод: | B132 4650 |
| Деталь: | Bracket:Stepper MotorJogger |
| Парткод: | B132 4696 |
| Деталь: | Stepper Motor:Transport:Assy |
| Парткод: | B132 4785 |
| Деталь: | Bracket:Stepper Motor:Transport |
| Парткод: | B132 4789 |
| Деталь: | Timing Belt:40S2M360G |
| Парткод: | AA04 3309 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Lever:Roller:Driven:Reversal |
| Парткод: | B132 4663 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2327 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Stay:Bearing:Reversal |
| Парткод: | B132 4665 |
| Деталь: | MAGNETIC |
| Парткод: | AA02 1 034 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA143183 |
| Деталь: | Jogger Fence:Front |
| Парткод: | B132 4681 |
| Деталь: | JOGGER FENCE:REAR |
| Парткод: | B132 4682 |
| Деталь: | Spring Plate - Rear Jogger Fence |
| Парткод: | B065 4683 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3811 |
| Деталь: | Table:Duplex:Left |
| Парткод: | B132 4720 |
| Деталь: | Arm:Roller:Reversal:Driven |
| Парткод: | B132 4661 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3592 |
| Деталь: | Driven Reversal Roller |
| Парткод: | AF02 0591 |
| Деталь: | Bushing - 8x10x5 |
| Парткод: | AA08 2063 |
| Деталь: | Reversal Roller Shaft |
| Парткод: | AA14 8631 |
| Деталь: | Bracket:Reversal:Driven:Assy |
| Парткод: | B132 4655 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Stay:Frame:Left |
| Парткод: | B477 1152 |
| Деталь: | Arm Shaft |
| Парткод: | B477 1171 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3020 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 1136 |
| Деталь: | Hinge:Left:Assy |
| Парткод: | B652 1210 |
| Деталь: | Contact Point Shaft |
| Парткод: | A806 1135 |
| Деталь: | Right Frame Stay |
| Парткод: | B477 1161 |
| Деталь: | Sheet: Exit: Lower |
| Парткод: | B652 1135 |
| Деталь: | Hinge:Right:Assy |
| Парткод: | B652 1220 |
| Деталь: | Sensor Feeler |
| Парткод: | B4771185 |
| Деталь: | Sensor bracket |
| Парткод: | B477 1181 |
| Деталь: | Detection Sensor Harness |
| Парткод: | B477 5611 |
| Деталь: | Harness:Sensor:Reverse:Upper |
| Парткод: | B652 5446 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B477 2621 |
| Деталь: | Bracket:Pressure:Transport Belt |
| Парткод: | B652 1131 |
| Деталь: | TENSION SPRING |
| Парткод: | B652 1132 |
| Деталь: | Pulley:Belt Tensioner |
| Парткод: | A257 6112 |
| Деталь: | Cover:Roller:Scanning:Peen |
| Парткод: | B652 3136 |
| Деталь: | Bracket:Magnet Catch:Pressure Plate |
| Парткод: | B652 4904 |
| Деталь: | Front Left Stopper |
| Парткод: | B477 1191 |
| Деталь: | Adjusting Pin:Transport Belt Unit |
| Парткод: | B652 1141 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Fusing Unit (NA) |
| Парткод: | B132 4017 |
| Деталь: | Fusing Unit (EU) |
| Парткод: | B132 4027 |
| Деталь: | Heater - 350W/120V |
| Парткод: | AX43 0140 |
| Деталь: | Heater - 350W/230V |
| Парткод: | AX43 0139 |
| Деталь: | Heater - 350W/230V |
| Парткод: | AX43 0137 |
| Деталь: | Heater - 350W/120V |
| Парткод: | AX43 0138 |
| Деталь: | Heater - 590W/230V |
| Парткод: | AX44 0225 |
| Деталь: | Heater - 590W/120V |
| Парткод: | AX44 0226 |
| Деталь: | Thermostat:190C:250V/17A |
| Парткод: | AW11 0042 |
| Деталь: | Thermostat:189C:250V/17A |
| Парткод: | AW11 0043 |
| Деталь: | Temperature Sensor:Assy |
| Парткод: | B132 4150 |
| Деталь: | Thermostat:149C:250V/17A |
| Парткод: | AW11 0045 |
| Деталь: | Thermostat:150C:250V/17A |
| Парткод: | AW11 0044 |
| Деталь: | Thermistor:Pressure Roller |
| Парткод: | AW10 0098 |
| Деталь: | Fusing Cover |
| Парткод: | B132 4061 |
| Деталь: | Stay:Fusing Unit |
| Парткод: | B132 4071 |
| Деталь: | Harness:Thermostat:Upper Middle |
| Парткод: | B132 4152 |
| Деталь: | Fusing Entrance Guide Plate:Upper |
| Парткод: | B132 4133 |
| Деталь: | Plate:Temperature Sensor:Front |
| Парткод: | B132 4158 |
| Деталь: | Heater Holder:Upper Front |
| Парткод: | B132 4144 |
| Деталь: | Plate:Temperature Sensor:Rear |
| Парткод: | B132 4159 |
| Деталь: | Heater Holder:Hot Roller |
| Парткод: | B132 4145 |
| Деталь: | Housing:Temperature Sensor |
| Парткод: | B132 4149 |
| Деталь: | Fusing Entrance Guide Plate:Lower |
| Парткод: | B132 4273 |
| Деталь: | Heater Holder:Lower |
| Парткод: | B132 4245 |
| Деталь: | Knob Screw - 4m |
| Парткод: | B051 4103 |
| Деталь: | Thermostat Terminal |
| Парткод: | B065 4121 |
| Деталь: | Fusing Protective Sheet |
| Парткод: | B132 4289 |
| Деталь: | Tag:Red:Short |
| Парткод: | A232 3936 |
| Деталь: | Manual Feed Unit:Assy |
| Парткод: | B132 2800 |
| Деталь: | Cover:Manual Feed Unit |
| Парткод: | B132 2859 |
| Деталь: | Holder:Manual Feed Table:Front |
| Парткод: | B132 2819 |
| Деталь: | Harness:Manual Feed Unit |
| Парткод: | B132 5249 |
| Деталь: | Feeler:Paper End Sensor |
| Парткод: | B132 2845 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Feeler Roller |
| Парткод: | A134 2661 |
| Деталь: | Bracket:Sensor:Manual Feed |
| Парткод: | B132 2848 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0952 |
| Деталь: | DC Solenoid:Pickup:Assy |
| Парткод: | B132 2839 |
| Деталь: | One-way Clutch |
| Парткод: | AA08 3014 |
| Деталь: | Gear:42z |
| Парткод: | AB01 1307 |
| Деталь: | Roller:Manual Feed Unit:Drive |
| Парткод: | B132 2856 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Stopper:Magnetic Clutch |
| Парткод: | B132 2857 |
| Деталь: | Holder:Manual Feed Table:Rear |
| Парткод: | B132 2823 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Paper Feed Roller:Feed:Manual Feed |
| Парткод: | AF031081 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | Gear -15T |
| Парткод: | 54 472 706 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0080 |
| Деталь: | Guide Plate:Feed |
| Парткод: | B132 2837 |
| Деталь: | Ground Plate:Manual Feed |
| Парткод: | B132 2846 |
| Деталь: | Arm:Pickup:Manual Feed |
| Парткод: | B132 2835 |
| Деталь: | Shaft:Feed Roller |
| Парткод: | AA14 0761 |
| Деталь: | Bushing - 8x18x11 |
| Парткод: | AA08 3013 |
| Деталь: | Magnetic Clutch:0.53N M:36Z |
| Парткод: | AX20 0277 |
| Деталь: | Guide Plate:Separator Assy |
| Парткод: | B132 2825 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3016 |
| Деталь: | Shaft:Separator:Drive:Assy |
| Парткод: | B132 2849 |
| Деталь: | Gear:24Z |
| Парткод: | AB01 1306 |
| Деталь: | Paper Feed Roller:Separate |
| Парткод: | AF03 2080 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A294 6700 |
| Деталь: | Shaft:Separator:Driven:Assy |
| Парткод: | B132 2851 |
| Деталь: | Gear:21Z |
| Парткод: | AB01 1305 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0954 |
| Деталь: | Le ve r: Press u re: Se pa rato r |
| Парткод: | B132 2853 |
| Деталь: | Paper Feed Motor - DC 7.4W |
| Парткод: | B477 3711 |
| Деталь: | Paper Feed Motor Stay |
| Парткод: | B477 3115 |
| Деталь: | Paper Feed Motor Bracket |
| Парткод: | B477 3111 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0842 |
| Деталь: | Spacer:Reverse Roller:Rear |
| Парткод: | B652 1633 |
| Деталь: | Gear -37Z |
| Парткод: | B477 3161 |
| Деталь: | Gear - 31Z |
| Парткод: | B477 3151 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | PULLEY |
| Парткод: | A548 2139 |
| Деталь: | Separation Shaft Stopper |
| Парткод: | A806 2244 |
| Деталь: | Gear - 24Z |
| Парткод: | B477 3123 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Separation Roller Shaft |
| Парткод: | B477 3121 |
| Деталь: | Feeler - Pick-up Roller Cam |
| Парткод: | A680 2262 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Pick-up Roller Cam |
| Парткод: | B477 3251 |
| Деталь: | Stepper Motor:MM42:0.95A:9.5V |
| Парткод: | AX04 0139 |
| Деталь: | Gear - 20Z |
| Парткод: | B477 3143 |
| Деталь: | Timing Belt:B40S3M186 |
| Парткод: | B652 1643 |
| Деталь: | Gear - 23Z |
| Парткод: | B477 3141 |
| Деталь: | PULLEY |
| Парткод: | B477 3177 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Timing Belt:B40S2M178 |
| Парткод: | B6521773 |
| Деталь: | Pulley - 39Z |
| Парткод: | B301 2141 |
| Деталь: | Timing Belt:B60S2M212 |
| Парткод: | B652 1613 |
| Деталь: | PULLEY |
| Парткод: | B477 3145 |
| Деталь: | Paper Feed Drive Bracket |
| Парткод: | B477 3181 |
| Деталь: | PULLEY |
| Парткод: | B477 3171 |
| Деталь: | Timing Belt:B40S2M170 |
| Парткод: | B652 1674 |
| Деталь: | Timing Belt:B40S3M180 |
| Парткод: | B652 1673 |
| Деталь: | PULLEY |
| Парткод: | B477 3173 |
| Деталь: | Damper - Junction Gate Solenoid |
| Парткод: | A697 2102 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 1134 |
| Деталь: | Shaft:Slider |
| Парткод: | B652 1133 |
| Деталь: | Guide:Relay:Paper Feed Unit |
| Парткод: | B132 6758 |
| Деталь: | Sheet:Micro Switch:12mm |
| Парткод: | B132 5999 |
| Деталь: | Bracket:Micro Switch:Paper Bank |
| Парткод: | B132 5971 |
| Деталь: | TORSION SPRING |
| Парткод: | B132 5869 |
| Деталь: | Screw:Micro Switch |
| Парткод: | B132 5868 |
| Деталь: | Transport Unit:Vertical Transport |
| Парткод: | B132 6751 |
| Деталь: | SPRING |
| Парткод: | AA06 3878 |
| Деталь: | Release Cover - Vertical Transport |
| Парткод: | B065 6429 |
| Деталь: | Decal - Grip |
| Парткод: | A029 2984 |
| Деталь: | Release Lever - Vertical Transport |
| Парткод: | B065 6426 |
| Деталь: | Release Button - Vertical Transport |
| Парткод: | B065 6428 |
| Деталь: | Release Lever - Vertical Transport |
| Парткод: | B065 6427 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3560 |
| Деталь: | Side Plate:Front:Vertical Transport |
| Парткод: | B132 6753 |
| Деталь: | Side Plate:Rear:Vertical Transport |
| Парткод: | B132 6754 |
| Деталь: | Pressure Plate:Transport Roller:Driven:No.1 |
| Парткод: | B132 6752 |
| Деталь: | Transport Pressure Plate |
| Парткод: | B065 6407 |
| Деталь: | Stepped Screw - M5 |
| Парткод: | AA14 3715 |
| Деталь: | Vertical Driven Roller |
| Парткод: | AF02 0295 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0241 |
| Деталь: | Spring - 10mm |
| Парткод: | AA06 3487 |
| Деталь: | Transport Roller |
| Парткод: | AF02 0562 |
| Деталь: | Gear - 24Z/40Z |
| Парткод: | AB01 7619 |
| Деталь: | Gear - 35Z |
| Парткод: | AB01 1466 |
| Деталь: | TIMING BELT |
| Парткод: | AA04 3575 |
| Деталь: | Joint Unit Guide Plate Assy |
| Парткод: | B140 6472 |
| Деталь: | Relay Unit Harness |
| Парткод: | B065 6489 |
| Деталь: | Supporting Plate:Side Plate |
| Парткод: | B132 3217 |
| Деталь: | Brushless Motor:Drive:Paper Feed |
| Парткод: | GX06 0015 |
| Деталь: | Bracket:Fix:Right |
| Парткод: | B132 3218 |
| Деталь: | Filter:Duct |
| Парткод: | B132 2475 |
| Деталь: | Cover:Lower:Black |
| Парткод: | B132 3229 |
| Деталь: | Gear:75Z |
| Парткод: | B132 3224 |
| Деталь: | Shaft:Drive |
| Парткод: | B132 3222 |
| Деталь: | Gear:21/32Z |
| Парткод: | B132 3223 |
| Деталь: | Guide:Shaft:Drive |
| Парткод: | AA08 2139 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Cover:Drawer |
| Парткод: | B132 3435 |
| Деталь: | Bracket: Drawer |
| Парткод: | B132 3434 |
| Деталь: | Bracket:PCB |
| Парткод: | B132 3431 |
| Деталь: | PCB:CNB |
| Парткод: | B132 5440 |
| Деталь: | Harness:CNB:Left |
| Парткод: | B132 5228 |
| Деталь: | Harness:Toner Hopper:Uni:Drawer:CNB |
| Парткод: | B132 5227 |
| Деталь: | SHEET |
| Парткод: | B132 3245 |
| Деталь: | Shield:Joint:PCU |
| Парткод: | B132 6578 |
| Деталь: | Case:Toner Outlet Sub-unit:Cover |
| Парткод: | B132 6519 |
| Деталь: | Case:Toner Outlet Sub-unit |
| Парткод: | B132 6518 |
| Деталь: | Toner Catchpan:Tank:Entrance |
| Парткод: | B132 6539 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Transport Screw:Upper:Assy |
| Парткод: | B132 6520 |
| Деталь: | Harness:Toner Recycling Section |
| Парткод: | B132 5393 |
| Деталь: | Photointerruptor:Feeler: Square |
| Парткод: | AW02 0147 |
| Деталь: | Base:Toner Outlet Sub-unit:Assy |
| Парткод: | B132 6512 |
| Деталь: | Bracket:Toner Outlet Sub-unit:Drive |
| Парткод: | B132 6514 |
| Деталь: | TENSION SPRING |
| Парткод: | B132 6542 |
| Деталь: | Gear:31/44Z |
| Парткод: | AB01 1029 |
| Деталь: | Shaft:Toner Outlet Sub-unit |
| Парткод: | B132 6527 |
| Деталь: | Shaft:Drive:Long:Assy |
| Парткод: | B132 6548 |
| Деталь: | Gear:18Z |
| Парткод: | AB01 3299 |
| Деталь: | Brushless motor |
| Парткод: | AX06 0302 |
| Деталь: | Cover:DC Motor |
| Парткод: | B132 6537 |
| Деталь: | Gear:14/30Z |
| Парткод: | AB01 1248 |
| Деталь: | Gear:32Z |
| Парткод: | AB01 1247 |
| Деталь: | Bushing:Transport Screw |
| Парткод: | B132 6536 |
| Деталь: | Toner Collection Gear |
| Парткод: | B065 3587 |
| Деталь: | Spacer - M6 |
| Парткод: | AA13 2208 |
| Деталь: | SPRING |
| Парткод: | B065 3561 |
| Деталь: | Guide:Spring:Discharge Used Toner |
| Парткод: | B132 6526 |
| Деталь: | Guide Plate:Left Upper:Assy |
| Парткод: | B132 7115 |
| Деталь: | Roller:MM14 |
| Парткод: | B132 7033 |
| Деталь: | Grip:Guide Plate:Left |
| Парткод: | B132 7015 |
| Деталь: | Guide Plat:Left Lower:Assy |
| Парткод: | B132 7110 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Spring:Guide Plate:Open And Close |
| Парткод: | AA06 3909 |
| Деталь: | Gate Pawl:Reverse |
| Парткод: | B132 7054 |
| Деталь: | Guide Plate:Middle:Transport |
| Парткод: | B132 7004 |
| Деталь: | Guide Plate:Middle:Left |
| Парткод: | B132 7064 |
| Деталь: | Arm: Pressure |
| Парткод: | B132 7045 |
| Деталь: | Shaft:Release:Guide Plate |
| Парткод: | B132 7029 |
| Деталь: | Plate:Transport Roller |
| Парткод: | B132 7132 |
| Деталь: | Lever:Release |
| Парткод: | B132 7098 |
| Деталь: | Guide Plate:Middle:Right |
| Парткод: | B132 7017 |
| Деталь: | Roller:Middle |
| Парткод: | B132 7031 |
| Деталь: | Spring Plate:Middle |
| Парткод: | B132 7020 |
| Деталь: | Stay:Supporting Plate |
| Парткод: | B132 7160 |
| Деталь: | Guide:Entrance:Right Rear |
| Парткод: | B132 7103 |
| Деталь: | Stay:Shaft:Assy |
| Парткод: | B132 7097 |
| Деталь: | Lever:Release:Guide Plate:Lower |
| Парткод: | B132 7046 |
| Деталь: | Side Plate:Rear:Assy |
| Парткод: | B132 7078 |
| Деталь: | DC Solenoid:Bracket:Assy |
| Парткод: | B132 7148 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 2330 |
| Деталь: | Side Plate:Front:Assy |
| Парткод: | B132 7076 |
| Деталь: | Carriage:No.2:Assy |
| Парткод: | B132 1801 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | Mirror:No.2 |
| Парткод: | B132 1818 |
| Деталь: | Mirror:No.3 |
| Парткод: | B132 1819 |
| Деталь: | Holder:Pulley |
| Парткод: | B132 1815 |
| Деталь: | Pulley - High Voltage Supply Cord |
| Парткод: | G570 2834 |
| Деталь: | Original Sensor:H1-66 |
| Парткод: | AW01 0116 |
| Деталь: | Original Sensor:H81.5 |
| Парткод: | AW01 0115 |
| Деталь: | Original Sensor:H2-66 |
| Парткод: | AW01 0114 |
| Деталь: | Bracket:Original Sensor |
| Парткод: | B132 1861 |
| Деталь: | Carriage:No.1 :Assy |
| Парткод: | B132 1751 |
| Деталь: | GRIP |
| Парткод: | G570 2731 |
| Деталь: | Feeler:Home Position Sensor:No.1 |
| Парткод: | B132 1766 |
| Деталь: | Holder:Connector |
| Парткод: | B1321767 |
| Деталь: | Stay:Wire |
| Парткод: | B132 1758 |
| Деталь: | REFLECTOR |
| Парткод: | B132 1762 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A1931767 |
| Деталь: | Mirror:No.1 :Assy |
| Парткод: | B1321757 |
| Деталь: | Harness:Connecting:Scanner:Lamp |
| Парткод: | B132 5304 |
| Деталь: | Xenon Lamp:100000LX |
| Парткод: | B1321890 |
| Деталь: | DC Motor:MM56:15W |
| Парткод: | AX06 0281 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket:Sensor |
| Парткод: | B1321307 |
| Деталь: | Bracket:Brushless Motor:Peen |
| Парткод: | B132 1291 |
| Деталь: | Gear:72Z |
| Парткод: | AB01 0136 |
| Деталь: | Gear:Pulley:72Z/20T |
| Парткод: | AB01 7684 |
| Деталь: | Gear:108Z |
| Парткод: | AB01 0137 |
| Деталь: | Bracket: Plate |
| Парткод: | B1321297 |
| Деталь: | Shaft:Drive:Cleaning |
| Парткод: | B132 1300 |
| Деталь: | Shaft:Drive:T ransfer |
| Парткод: | B1321295 |
| Деталь: | Stepped Screw - Guide Plate |
| Парткод: | 52 164 198 |
| Деталь: | Receptacle:Connector:6p |
| Парткод: | B132 2325 |
| Деталь: | Receptacle:Development Vias:Assy |
| Парткод: | B132 3186 |
| Деталь: | Harness:T :Sensor:Drawer |
| Парткод: | B132 5272 |
| Деталь: | Harness:Development:BM |
| Парткод: | B132 5340 |
| Деталь: | Harness:Development:CY |
| Парткод: | B132 5342 |
| Деталь: | Bracket:Drawer:Paper Feed Unit |
| Парткод: | B1321020 |
| Деталь: | Screw:Spring:Drawer |
| Парткод: | AA14 3794 |
| Деталь: | Spring Connector:9.8n |
| Парткод: | AA06 3670 |
| Деталь: | Duct:Joint:Fusing |
| Парткод: | B132 2428 |
| Деталь: | Connector Guide Pin |
| Парткод: | AA14 3797 |
| Деталь: | Harness:Duplex:DRB:Drawer |
| Парткод: | B132 5260 |
| Деталь: | Receptacle:Assy |
| Парткод: | B132 3650 |
| Деталь: | Bracket:Spring Plate:Assy |
| Парткод: | B132 7107 |
| Деталь: | Duct:Connecting:Pull Out:Rear |
| Парткод: | B132 2461 |
| Деталь: | Harness:Sensor:Drawer:Black |
| Парткод: | B132 5270 |
| Деталь: | Harness:Sensor:Drawer:MCY |
| Парткод: | B132 5271 |
| Деталь: | Duct:Joint:Fusing:Rear |
| Парткод: | B132 2453 |
| Деталь: | Inner Cover:Duplex Unit:Assy |
| Парткод: | B132 4525 |
| Деталь: | Decal:Warning (High Temperature) |
| Парткод: | B132 4797 |
| Деталь: | Duplex Unit:Assy |
| Парткод: | B132 4500 |
| Деталь: | Grip:Release:Duplex Unit |
| Парткод: | B132 4674 |
| Деталь: | Release Lever Shaft |
| Парткод: | B065 4673 |
| Деталь: | Arm:Lock:Duplex |
| Парткод: | B132 4671 |
| Деталь: | Duplex Release Bracket |
| Парткод: | B065 4675 |
| Деталь: | SPRING |
| Парткод: | AA06 2320 |
| Деталь: | Release Lever Bracket |
| Парткод: | B065 4672 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Stay:Duplex Unit:Upper |
| Парткод: | B132 4987 |
| Деталь: | Guide Plate:Jogger:Upper |
| Парткод: | B132 4874 |
| Деталь: | Guide Plate:Duplex:Exit |
| Парткод: | B132 4869 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA14 3811 |
| Деталь: | Table:Duplex:Right |
| Парткод: | B132 4725 |
| Деталь: | Bracket:Sensor:Right |
| Парткод: | B132 4727 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0149 |
| Деталь: | Harness:Sensor:Duplex:3p |
| Парткод: | B132 5263 |
| Деталь: | GUIDE PLATE:TRANSPORT:LOWER |
| Парткод: | B132 4730 |
| Деталь: | Spring Plate - Driven Roller |
| Парткод: | B065 4731 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2077 |
| Деталь: | Guide Plate Band |
| Парткод: | A096 4928 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3581 |
| Деталь: | Guide Plate Pressure Holder |
| Парткод: | A229 4727 |
| Деталь: | Guide Stopper Roller |
| Парткод: | AF02 2067 |
| Деталь: | Guide Plate Lever |
| Парткод: | B065 4531 |
| Деталь: | Decal - Guide Plate Lever |
| Парткод: | B065 4867 |
| Деталь: | Guide Plate Lever Hook |
| Парткод: | B065 4933 |
| Деталь: | Gate Pawl:Reverse:Lower:Left |
| Парткод: | B652 4527 |
| Деталь: | Gate Pawl:Reverse:Lower:Right |
| Парткод: | B652 4528 |
| Деталь: | Cushion - Bin Solenoid Lever |
| Парткод: | A458 2251 |
| Деталь: | Bushing:Reverse:Lower:Gate Pawl |
| Парткод: | B652 4520 |
| Деталь: | Roller:Scanning:Exit:Driven |
| Парткод: | B652 4519 |
| Деталь: | Driven Exit Arm |
| Парткод: | B477 2637 |
| Деталь: | Exit Arm Spring |
| Парткод: | B477 4127 |
| Деталь: | Guide Plate:Reverse:Lower |
| Парткод: | B652 4516 |
| Деталь: | Stepped Screw - M6 |
| Парткод: | A232 2356 |
| Деталь: | Short Arm Shaft |
| Парткод: | B477 2645 |
| Деталь: | Long Arm Shaft |
| Парткод: | B477 2641 |
| Деталь: | Lever:Reverse:Lower |
| Парткод: | B652 4529 |
| Деталь: | Driven Exit Scanning Roller |
| Парткод: | B477 2636 |
| Деталь: | Arm:Pressure:Reverse:Lower |
| Парткод: | B652 4517 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 4518 |
| Деталь: | TENSION SPRING |
| Парткод: | B652 4530 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B477 2621 |
| Деталь: | Bracket:Reverse:Lower |
| Парткод: | B652 4522 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | EXIT ROLLER |
| Парткод: | B652 4726 |
| Деталь: | Guide Plate:Reverse:Lower:Fix |
| Парткод: | B652 4602 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B6521853 |
| Деталь: | Bushing- Exit Driven Roller |
| Парткод: | A859 4836 |
| Деталь: | DRIVEN EXIT ROLLER |
| Парткод: | B477 2861 |
| Деталь: | Cover: Exit |
| Парткод: | B652 1852 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Harness:Sensor:Reverse:Lower |
| Парткод: | B652 5456 |
| Деталь: | Cover:Sensor:Reverse:Lower |
| Парткод: | B652 1854 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Timing Pulley:44t |
| Парткод: | B652 4727 |
| Деталь: | Harnessd:Electric Potential Sensor |
| Парткод: | B132 5229 |
| Деталь: | Harness:Sensor:KM |
| Парткод: | B132 5357 |
| Деталь: | Harness:Sensor:CY |
| Парткод: | B132 5358 |
| Деталь: | Power Pack:B |
| Парткод: | AZ320137 |
| Деталь: | Base:Electric Potential Sensor |
| Парткод: | B132 5415 |
| Деталь: | Bracket:Power Pack:Development |
| Парткод: | B132 5861 |
| Деталь: | Stay:Bracket:Power Pack:Development |
| Парткод: | B132 5863 |
| Деталь: | Harness:DRB:ADF:Power Source |
| Парткод: | B132 5258 |
| Деталь: | Stay:Harness:Power Pack:Development |
| Парткод: | B132 5864 |
| Деталь: | Stay:Duct |
| Парткод: | B132 2431 |
| Деталь: | Duct:Exhaust |
| Парткод: | B132 2434 |
| Деталь: | Duct:Joint:Exhaust:Assy |
| Парткод: | B132 2455 |
| Деталь: | Seal:Duct:Exhaust |
| Парткод: | B132 2479 |
| Деталь: | Bracket:Stay:Duct |
| Парткод: | B132 2432 |
| Деталь: | Duct:Exhaust:Assy |
| Парткод: | B132 6861 |
| Деталь: | Fan Motor MM80 |
| Парткод: | AX64 0159 |
| Деталь: | Bracket:Stay:Duct:Right |
| Парткод: | B132 2433 |
| Деталь: | Duct:Exit:Exhaust:Assy |
| Парткод: | B132 6901 |
| Деталь: | Fan:Sirocco:DC24V:2speed |
| Парткод: | AX65 0042 |
| Деталь: | Shield:Sirocco |
| Парткод: | B132 6966 |
| Деталь: | Paper Tray:Universal:DOM:Assy |
| Парткод: | B132 6770 |
| Деталь: | Link:Side Fence |
| Парткод: | B132 6789 |
| Деталь: | Link:End Fence |
| Парткод: | B132 6788 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B132 6793 |
| Деталь: | Positioning Stopper Lever |
| Парткод: | B065 6538 |
| Деталь: | Spring Plate |
| Парткод: | A134 2978 |
| Деталь: | Plate:Side Fence |
| Парткод: | B132 6791 |
| Деталь: | Side Fence Pad |
| Парткод: | A096 6553 |
| Деталь: | Tray Bottom Plate:Assy |
| Парткод: | B132 6785 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3005 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B132 6795 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA00 2010 |
| Деталь: | Spring Plate:Paper Tray:Earth |
| Парткод: | B132 6798 |
| Деталь: | Decal:Paper Tray:Paper Set Direction |
| Парткод: | B132 6786 |
| Деталь: | Decal - Positioning |
| Парткод: | B065 6545 |
| Деталь: | Arm:End Fence:Lock |
| Парткод: | B132 6783 |
| Деталь: | END FENCE |
| Парткод: | AF01 7032 |
| Деталь: | Side Fence:Rear:Auxiliary |
| Парткод: | B132 6797 |
| Деталь: | Gear:16z |
| Парткод: | AB01 2327 |
| Деталь: | Misfeed Removal Guide |
| Парткод: | A176 6695 |
| Деталь: | Tension Spring:Side Fence:Rear |
| Парткод: | AA06 0961 |
| Деталь: | Bottom Plate Lift Shaft |
| Парткод: | B065 6524 |
| Деталь: | Lift Lever |
| Парткод: | B065 6526 |
| Деталь: | Tandem LCT Unit:Right (NA) |
| Парткод: | B132 7506 |
| Деталь: | Tandem LCT Unit:Right (EU) |
| Парткод: | B132 7505 |
| Деталь: | Inner Cover:Tandem LCT |
| Парткод: | B132 7586 |
| Деталь: | Decal - Caution |
| Парткод: | AA00 2246 |
| Деталь: | Right Stopper |
| Парткод: | B065 6859 |
| Деталь: | Protection -inner Cover |
| Парткод: | B065 6875 |
| Деталь: | Decal - Paper Set - Right |
| Парткод: | B065 6877 |
| Деталь: | Side Fence:Right Front |
| Парткод: | B132 7578 |
| Деталь: | Plate:Paper:Assy |
| Парткод: | A294 6734 |
| Деталь: | Base:Tandem LCT:Right |
| Парткод: | B132 7543 |
| Деталь: | Friction pad |
| Парткод: | 52 012 858 |
| Деталь: | Sensor bracket |
| Парткод: | A294 6706 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Misfeed Removal Guide |
| Парткод: | A176 6695 |
| Деталь: | Seal - 4x10x70 (B181/B200) |
| Парткод: | AA15 3063 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA00 2010 |
| Деталь: | Side Fence:Tandem LCT:Right |
| Парткод: | B132 7576 |
| Деталь: | Side plate |
| Парткод: | A294 6666 |
| Деталь: | Decal - Right Paper Set |
| Парткод: | A096 6677 |
| Деталь: | Interlock Guide - Tandem LCT |
| Парткод: | B065 6672 |
| Деталь: | Exit Roller:Exit:Drive |
| Парткод: | B132 7086 |
| Деталь: | Reverse Roller:Drive |
| Парткод: | B132 7081 |
| Деталь: | Guide Plate:Shaft:Assy |
| Парткод: | B132 7151 |
| Деталь: | Roller:Middle |
| Парткод: | B132 7087 |
| Деталь: | Roller:Middle:Duplex Sub-unit |
| Парткод: | B132 7088 |
| Деталь: | Roller:Decura:Entrance |
| Парткод: | B132 7161 |
| Деталь: | Roller:Decura:Exit |
| Парткод: | B132 7085 |
| Деталь: | Washer M6 - Scanner Unit |
| Парткод: | H0531174 |
| Деталь: | Spring - Lower Exit Roller |
| Парткод: | A4701704 |
| Деталь: | Shift Clutch |
| Парткод: | A4701703 |
| Деталь: | Pulley:19Z |
| Парткод: | B132 7051 |
| Деталь: | Timing Belt:T198 |
| Парткод: | B132 7116 |
| Деталь: | Tightener:Front Upper:Assy |
| Парткод: | B132 7112 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0695 |
| Деталь: | Pulley:13T |
| Парткод: | B132 7048 |
| Деталь: | Roller:Tightener |
| Парткод: | B132 7025 |
| Деталь: | Bracket:Connector |
| Парткод: | B132 7069 |
| Деталь: | Pulley:15T |
| Парткод: | B132 7036 |
| Деталь: | Pulley:15T |
| Парткод: | B132 7028 |
| Деталь: | Timing Belt:T213 |
| Парткод: | B132 7117 |
| Деталь: | Roller:Tightener |
| Парткод: | B132 7059 |
| Деталь: | Shaft:Base:Tightener |
| Парткод: | B132 7141 |
| Деталь: | Pulley:37T |
| Парткод: | B132 7080 |
| Деталь: | Spring:Tightener |
| Парткод: | B132 7143 |
| Деталь: | Gear:Z20 |
| Парткод: | B132 7138 |
| Деталь: | Gear:Z28 |
| Парткод: | B132 7144 |
| Деталь: | Pulley:Z13 |
| Парткод: | B132 7162 |
| Деталь: | Gear:Z27 |
| Парткод: | B132 7030 |
| Деталь: | Gear:29Z |
| Парткод: | B132 7060 |
| Деталь: | Gear:22Z |
| Парткод: | B132 7055 |
| Деталь: | Stopper:Guide |
| Парткод: | B132 7155 |
| Деталь: | Stabilizer |
| Парткод: | B132 1891 |
| Деталь: | Bracket:Invertor |
| Парткод: | B132 1851 |
| Деталь: | Bracket:Fan:MM40: Invertor |
| Парткод: | B132 1852 |
| Деталь: | Fan Motor:15mm:24V |
| Парткод: | AX64 0164 |
| Деталь: | Screw:6x1.7 |
| Парткод: | AA14 3802 |
| Деталь: | Pulley:Tension:Timing Belt:Assy |
| Парткод: | B132 1710 |
| Деталь: | Bracket: Motor |
| Парткод: | B132 1702 |
| Деталь: | PRESSURE SPRING |
| Парткод: | G029 4150 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | A1341724 |
| Деталь: | Stepper Motor:Scanner |
| Парткод: | B132 1703 |
| Деталь: | Cover:Damper |
| Парткод: | B132 1714 |
| Деталь: | Cover:Shaft |
| Парткод: | B132 1716 |
| Деталь: | Drive Were:Scanner |
| Парткод: | B1321729 |
| Деталь: | Bracket:Tension |
| Парткод: | B132 1724 |
| Деталь: | Bracket:Tension:Fix |
| Парткод: | B1321725 |
| Деталь: | Spring:Drive Were |
| Парткод: | B132 1723 |
| Деталь: | Timing Belt:100S2M266 |
| Парткод: | AA04 3314 |
| Деталь: | Pulley:40T |
| Парткод: | B1321720 |
| Деталь: | PULLEY |
| Парткод: | AB03 2070 |
| Деталь: | Screw:Mechanical Drive Section |
| Парткод: | B132 1719 |
| Деталь: | Harness:SIOB:SBU |
| Парткод: | B132 5301 |
| Деталь: | Harness:SIOB:Fan Motor |
| Парткод: | B132 5302 |
| Деталь: | Harness:SIOB:Original Sensor |
| Парткод: | B132 5300 |
| Деталь: | PCB:SIOB |
| Парткод: | B132 5495 |
| Деталь: | Bracket:Pulley |
| Парткод: | B132 1671 |
| Деталь: | PULLEY |
| Парткод: | AB03 2069 |
| Деталь: | Cover:Polygon Mirror Motor |
| Парткод: | B1321675 |
| Деталь: | Fan Motor:Mm60 |
| Парткод: | AX64 0151 |
| Деталь: | Gasket:Cover:Shaft |
| Парткод: | B1321728 |
| Деталь: | Tension Spring:Hot Roller |
| Парткод: | B132 4194 |
| Деталь: | STAY:UPPER |
| Парткод: | B132 4103 |
| Деталь: | Bracket:Guide Plate:Upper |
| Парткод: | B132 4132 |
| Деталь: | Fusing Belt |
| Парткод: | B132 4089 |
| Деталь: | Gear:Upper:52Z |
| Парткод: | AB01 3635 |
| Деталь: | Hot Roller |
| Парткод: | AE01 0052 |
| Деталь: | Lever:Heat Roller:Rear |
| Парткод: | B132 4120 |
| Деталь: | HEAT ROLLER |
| Парткод: | B132 4084 |
| Деталь: | Side Plate:Upper Rear |
| Парткод: | B132 4101 |
| Деталь: | Harness:Fusing Unit:No.2 |
| Парткод: | B132 5205 |
| Деталь: | Ball Bearing:DIA30xDIA37x7 |
| Парткод: | AE03 0057 |
| Деталь: | Thermal Insulating Bushing |
| Парткод: | AE03 2027 |
| Деталь: | Gear:Hot Roller:44z |
| Парткод: | AB01 3620 |
| Деталь: | Gear - 46Z |
| Парткод: | AB01 3702 |
| Деталь: | Gear:Drive:Press Fit |
| Парткод: | B132 4123 |
| Деталь: | Harness:Thermostat:Upper Front |
| Парткод: | B132 4151 |
| Деталь: | Lever:Heat Roller:Front |
| Парткод: | B132 4121 |
| Деталь: | Side Plate:Upper Front |
| Парткод: | B132 4102 |
| Деталь: | Collar:Shaft:Drive |
| Парткод: | B132 4125 |
| Деталь: | Roller: Coupling:Knob:Fusing |
| Парткод: | B132 4138 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 3703 |
| Деталь: | Ball Bearing:DIA25:DIA37 |
| Парткод: | AE03 0058 |
| Деталь: | Ball Bearing - 8x15.6x4mm |
| Парткод: | AE030013 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | A077 4239 |
| Деталь: | Adjusting Pin:Heat Roller |
| Парткод: | B132 4122 |
| Деталь: | Harness Clamp |
| Парткод: | B132 4189 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Heater Holder:Upper Rear |
| Парткод: | B132 4143 |
| Деталь: | Spacer:Gear:Idler |
| Парткод: | B132 4119 |
| Деталь: | Stopper:Heat Roller:Upper Rear |
| Парткод: | B132 4147 |
| Деталь: | PAPER FEED UNIT |
| Парткод: | B132 6620 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF03 0081 |
| Деталь: | Paper Feed Roller:Feed |
| Парткод: | AF03 1082 |
| Деталь: | Pick-up Gear Cover |
| Парткод: | B065 6350 |
| Деталь: | Idler Gear |
| Парткод: | AB01 1465 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Pick-up Arm |
| Парткод: | B065 6357 |
| Деталь: | SPRING |
| Парткод: | AA06 0898 |
| Деталь: | Feed Roller Shaft |
| Парткод: | AA14 0828 |
| Деталь: | Feed Lever |
| Парткод: | B065 6445 |
| Деталь: | SPRING |
| Парткод: | AA06 0897 |
| Деталь: | Paper Feed Sensor Bracket |
| Парткод: | B065 6358 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Feed Stay |
| Парткод: | B065 6364 |
| Деталь: | Upper Paper Feed Harness |
| Парткод: | B065 6488 |
| Деталь: | SPRING |
| Парткод: | AA06 0899 |
| Деталь: | DC Solenoid:Pickup:Assy |
| Парткод: | B132 6659 |
| Деталь: | Gear - 21Z/38Z |
| Парткод: | AB01 7617 |
| Деталь: | Paper End Sensor Bracket |
| Парткод: | B065 6345 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Lower Paper Feed Harness |
| Парткод: | B065 6487 |
| Деталь: | Paper Feed Guide Plate |
| Парткод: | B140 6339 |
| Деталь: | Transport Roller |
| Парткод: | AF02 0562 |
| Деталь: | Gear - 35Z |
| Парткод: | AB01 1466 |
| Деталь: | Heat Sink Base |
| Парткод: | B065 6334 |
| Деталь: | Heat Sink Spring |
| Парткод: | AA06 3889 |
| Деталь: | HEAT SINK |
| Парткод: | B065 6337 |
| Деталь: | Heat Sink Sheet |
| Парткод: | B065 6338 |
| Деталь: | Paper Feed Unit Stay |
| Парткод: | B065 6375 |
| Деталь: | Drive bracket |
| Парткод: | B065 6366 |
| Деталь: | Feed Gear Cover |
| Парткод: | B065 6353 |
| Деталь: | Driven Pressure Lever |
| Парткод: | B065 6457 |
| Деталь: | SPRING |
| Парткод: | AA06 0896 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA14 3718 |
| Деталь: | Decal -Paper Tray 1 |
| Парткод: | B065 6635 |
| Деталь: | Cover:Tandem LCT |
| Парткод: | B132 6671 |
| Деталь: | Tandem LCT Unit:Left (NA) |
| Парткод: | B132 7513 |
| Деталь: | Tandem LCT Unit:Left (EU) |
| Парткод: | B132 7512 |
| Деталь: | LEFT SIDE PLATE |
| Парткод: | A294 6645 |
| Деталь: | Bracket:Cover:Tandem LCT:Assy |
| Парткод: | B070 6516 |
| Деталь: | Decal - Paper Set - Left |
| Парткод: | B065 6846 |
| Деталь: | Left Front Fence |
| Парткод: | A294 6643 |
| Деталь: | Tray Bottom Plate:Left Front |
| Парткод: | B132 7540 |
| Деталь: | Tray Bottom Plate:Left Middle:Assy |
| Парткод: | B098 6639 |
| Деталь: | Tray Bottom Plate:Left Rear |
| Парткод: | B132 7541 |
| Деталь: | Decal - Left Paper Set |
| Парткод: | A096 6678 |
| Деталь: | Left Rear Fence |
| Парткод: | A294 6630 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA00 2010 |
| Деталь: | Stopper - Interlock Switch |
| Парткод: | A294 6650 |
| Деталь: | Timing Pulley - 15T |
| Парткод: | AB03 3085 |
| Деталь: | Pulley Braket |
| Парткод: | B065 6821 |
| Деталь: | Tension Spring:Timing Belt:10n |
| Парткод: | AA06 0987 |
| Деталь: | Shaft - Back Fence Slider |
| Парткод: | AA14 0685 |
| Деталь: | Slider:Back Fence:Left |
| Парткод: | B132 7564 |
| Деталь: | Timing Belt Cover |
| Парткод: | B065 6823 |
| Деталь: | Back Fence:Left |
| Парткод: | B132 7561 |
| Деталь: | Timing Belt S3M 196T |
| Парткод: | AA04 3271 |
| Деталь: | Pulley Bracket |
| Парткод: | B065 6830 |
| Деталь: | Gear - 48T |
| Парткод: | AB01 9475 |
| Деталь: | Timing Pulley - 15T |
| Парткод: | AB03 3084 |
| Деталь: | DC Harness - Left |
| Парткод: | B070 5473 |
| Деталь: | Shaft - Timing Pulley |
| Парткод: | AA14 0686 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Gear - Z18 |
| Парткод: | AB01 3798 |
| Деталь: | Left DC Motor Bracket |
| Парткод: | B070 6666 |
| Деталь: | DC Motor:Tandem LCT |
| Парткод: | AX04 0145 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0163 |
| Деталь: | Base:Tandem LCT:Left:Assy |
| Парткод: | B065 6832 |
| Деталь: | Bracket:Photointerruptor:Left |
| Парткод: | B132 7566 |
| Деталь: | Coupling Lever - Left |
| Парткод: | A248 6615 |
| Деталь: | INTERFACE CABLE |
| Парткод: | B132 5369 |
| Деталь: | Cable:LVDS:LDB |
| Парткод: | B132 5367 |
| Деталь: | PCB:BICU |
| Парткод: | B132 5130 |
| Деталь: | PCB:IOB |
| Парткод: | B132 5410 |
| Деталь: | Harness:Upper Front |
| Парткод: | B132 5375 |
| Деталь: | Harness:Upper Rear |
| Парткод: | B132 5231 |
| Деталь: | Harness:Middle |
| Парткод: | B132 5379 |
| Деталь: | Harness:IOB:PP1 :pFC |
| Парткод: | B132 5381 |
| Деталь: | Harness:Shielded Wire:MB |
| Парткод: | B132 5214 |
| Деталь: | PCB:PPB |
| Парткод: | B132 5435 |
| Деталь: | Bracket:PPB |
| Парткод: | B132 5960 |
| Деталь: | Bracket:Mother Board |
| Парткод: | B132 5961 |
| Деталь: | Harness:CSS |
| Парткод: | B132 5370 |
| Деталь: | PCB:DDR-DIMM:256MB |
| Парткод: | B132 5763 |
| Деталь: | PCB:Mother Board |
| Парткод: | B132 5766 |
| Деталь: | Harness:HDD:Fan Motor |
| Парткод: | B132 5993 |
| Деталь: | Bracket:CSS |
| Парткод: | B132 5966 |
| Деталь: | PCB:N-PI:Assy |
| Парткод: | B188 5731 |
| Деталь: | Guide Plate:Paper Feed:Lower |
| Парткод: | B652 2142 |
| Деталь: | Separation Cap |
| Парткод: | B477 2151 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Separation Support Pad |
| Парткод: | B301 1155 |
| Деталь: | Separation Pad Holder |
| Парткод: | B301 1156 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Reverse Roller |
| Парткод: | A859 2241 |
| Деталь: | Torque Limiter - Separator |
| Парткод: | A293 6399 |
| Деталь: | Compression Spring:0.5n |
| Парткод: | B652 4156 |
| Деталь: | Bushing - 4mm |
| Парткод: | A680 1661 |
| Деталь: | Roller:Driven:Reverse:Middle |
| Парткод: | B652 4155 |
| Деталь: | Bracket:Guide Plate:Lower |
| Парткод: | B652 2127 |
| Деталь: | Reverse Roller Shaft |
| Парткод: | B477 3131 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Cushion:Guide Plate:Reverse:Exit |
| Парткод: | B652 2128 |
| Деталь: | Stay:Reverse Roller:Assy |
| Парткод: | B652 2122 |
| Деталь: | Guide:Stay:Reverse Roller |
| Парткод: | B652 2126 |
| Деталь: | Guide Plate:Original Table |
| Парткод: | B652 2432 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Gate Pawl:Reverse:Upper |
| Парткод: | B652 4203 |
| Деталь: | Cushion - Bin Solenoid Lever |
| Парткод: | A458 2251 |
| Деталь: | Bracket:Discharge Brush:Assy |
| Парткод: | B652 4205 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | A681 2416 |
| Деталь: | EXIT ROLLER |
| Парткод: | B652 4726 |
| Деталь: | Bracket:Sensor:Reverse:Middle |
| Парткод: | B652 4133 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Guide Plate:Reverse:Middle:Upper |
| Парткод: | B652 4122 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Hook:Solenoid:Reverse:Upper |
| Парткод: | B652 4212 |
| Деталь: | Tension Spring:Hook:Gate Pawl |
| Парткод: | B652 4213 |
| Деталь: | Timing Pulley:44t |
| Парткод: | B652 4727 |
| Деталь: | Operating Instructions - Security (NA) |
| Парткод: | B132 8307 |
| Деталь: | Operating Instructions - Main (NA) |
| Парткод: | B132 8607 |
| Деталь: | Operating Instructions - Copy (NA) |
| Парткод: | B132 8707 |
| Деталь: | O/I Holder - Assembly |
| Парткод: | B027 8521 |
| Деталь: | Cloth Holder |
| Парткод: | B065 1371 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B065 1374 |
| Деталь: | Sponge:SD-Card:Plate |
| Парткод: | B1321529 |
| Деталь: | Lever:Guide Plate |
| Парткод: | B132 1511 |
| Деталь: | Holder: Stand |
| Парткод: | B1321226 |
| Деталь: | Decal - Paper Size (B181) |
| Парткод: | B065 8490 |
| Деталь: | Inner Cover:Paper Feed |
| Парткод: | B132 1558 |
| Деталь: | Inner Cover:Paper Feed |
| Парткод: | B132 6761 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | B0701307 |
| Деталь: | Hinge:Door:Lower:Assy |
| Парткод: | B1321453 |
| Деталь: | Tray:Holder:PCU |
| Парткод: | B132 2393 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 1012 |
| Деталь: | Holder: PCU |
| Парткод: | B132 2391 |
| Деталь: | Plate:Drum Shaft |
| Парткод: | B132 2392 |
| Деталь: | Gear:Development Roller |
| Парткод: | B132 3120 |
| Деталь: | Adjusting Pin:Development |
| Парткод: | B132 3079 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Sheet:Logo:NA (B181) |
| Парткод: | B1321533 |
| Деталь: | Sheet:Logo:Lan:LDC160C (B181) |
| Парткод: | B132 1537 |
| Деталь: | Sheet:Logo:Nsa:DSC460 (B181) |
| Парткод: | B1321538 |
| Деталь: | Sheet:Logo:Rex:DSC460 (B181) |
| Парткод: | B132 1539 |
| Деталь: | Sheet:Logo:Ges:DSC460:EU (B181) |
| Парткод: | B1321540 |
| Деталь: | Sheet:Logo:Inf:ISC4560 (B181) |
| Парткод: | B132 1541 |
| Деталь: | Sheet:Logo:Aficio5560 (B200) |
| Парткод: | B2001533 |
| Деталь: | Sheet:Logo:Svn:SDC555 (B200) |
| Парткод: | B2001535 |
| Деталь: | Sheet:Logo:Ges:CS555 (B200) |
| Парткод: | B200 1536 |
| Деталь: | Sheet:Logo:Lan:LC155 (B200) |
| Парткод: | B2001537 |
| Деталь: | Sheet:Logo:Nsa:CS555 (B200) |
| Парткод: | B2001538 |
| Деталь: | Sheet:Logo:Rex:CS555 (B200) |
| Парткод: | B2001539 |
| Деталь: | Sheet:Logo:Ges:CS555:EU (B200) |
| Парткод: | B2001540 |
| Деталь: | Hinge:Door:Upper |
| Парткод: | B132 1452 |
| Деталь: | Door:Front:Assy |
| Парткод: | B132 1456 |
| Деталь: | Cover:Main Switch |
| Парткод: | B132 1512 |
| Деталь: | Case:Main Switch |
| Парткод: | B132 1513 |
| Деталь: | Grip:Door:Front |
| Парткод: | B132 1514 |
| Деталь: | Lever:Micro Switch |
| Парткод: | B132 1515 |
| Деталь: | Door Catch |
| Парткод: | B1321526 |
| Деталь: | Cap:Toner Supply:Upper |
| Парткод: | B132 3179 |
| Деталь: | Holder:Cap:Receiving Sub-unit |
| Парткод: | B132 3084 |
| Деталь: | Stopper:Charge |
| Парткод: | B027 31 70 |
| Деталь: | Toner Collection Coil |
| Парткод: | AD04 3086 |
| Деталь: | Case:Belt Cleaning:Assy |
| Парткод: | B132 6503 |
| Деталь: | Holder:Spring:Roller:Pressure |
| Парткод: | B132 6459 |
| Деталь: | Spring:Roller:Pressure |
| Парткод: | AA06 3423 |
| Деталь: | Case:Spring:Roller:Pressure |
| Парткод: | B132 6460 |
| Деталь: | Gear:12Z |
| Парткод: | AB01 3296 |
| Деталь: | Bushing:Holder:Blade |
| Парткод: | AA08 3021 |
| Деталь: | Ground Plate:Belt Cleaning |
| Парткод: | B132 6462 |
| Деталь: | Spring:Joint:Discharge Used Toner |
| Парткод: | AA06 3424 |
| Деталь: | Joint:Discharge Used Toner |
| Парткод: | B132 6461 |
| Деталь: | Roller:Pressure |
| Парткод: | B132 6469 |
| Деталь: | Shield:Case:Belt Cleaning:No.2 |
| Парткод: | AA15 2371 |
| Деталь: | Shield:Case:Belt Cleaning |
| Парткод: | AA15 2370 |
| Деталь: | Belt Cleaning Blade |
| Парткод: | AD04 1107 |
| Деталь: | Spring:Blade:Belt Cleaning |
| Парткод: | AA06 0094 |
| Деталь: | Holder:Blade:Belt Cleaning:Assy |
| Парткод: | B132 6470 |
| Деталь: | Joint:Drive:Brush:Belt Cleaning |
| Парткод: | B132 6475 |
| Деталь: | Seal:Upper:Belt Cleaning |
| Парткод: | B132 6120 |
| Деталь: | Cover:Case:Coating Bar |
| Парткод: | B132 6453 |
| Деталь: | Brush:Belt Cleaning |
| Парткод: | AD04 2071 |
| Деталь: | Bushing:Brush:Rear |
| Парткод: | AA08 0279 |
| Деталь: | Case:Coating Bar:Assy |
| Парткод: | B132 6450 |
| Деталь: | Belt Cleaning Scraper Blade |
| Парткод: | AD04 1109 |
| Деталь: | Roller:Bias |
| Парткод: | B132 6468 |
| Деталь: | Receptacle: Brush :Assy |
| Парткод: | B132 6454 |
| Деталь: | Gear -13Z |
| Парткод: | AB01 3298 |
| Деталь: | Gear -13Z |
| Парткод: | AB01 3297 |
| Деталь: | Gear -13Z |
| Парткод: | AB01 3295 |
| Деталь: | Bushing:Brush:Front |
| Парткод: | AA08 0278 |
| Деталь: | Shield:Cover:Coating Bar:Side |
| Парткод: | AA15 2368 |
| Деталь: | Snap Ring |
| Парткод: | G011 1058 |
| Деталь: | Shield:Brush:Front |
| Парткод: | AA15 2366 |
| Деталь: | Seal:Brush:Rear |
| Парткод: | AA15 2316 |
| Деталь: | Seal:Case:Coating Bar |
| Парткод: | AA15 2372 |
| Деталь: | Stay:Roller:Pressure:Front |
| Парткод: | B132 6484 |
| Деталь: | Stay:Roller:Pressure:Rear |
| Парткод: | B132 6485 |
| Деталь: | Decal - Cover |
| Парткод: | B065 4480 |
| Деталь: | Cover:Left Middle |
| Парткод: | B132 1506 |
| Деталь: | Cover:Left Lower |
| Парткод: | B1321509 |
| Деталь: | Waste Toner Bottle |
| Парткод: | B132 6596 |
| Деталь: | Rivet - M6 |
| Парткод: | B0391367 |
| Деталь: | Cover:Ozone Filter |
| Парткод: | B132 1516 |
| Деталь: | Cover:Rear Middle |
| Парткод: | B132 1507 |
| Деталь: | Screw:M4:Exterior |
| Парткод: | AA14 3801 |
| Деталь: | Cover:Rear Upper |
| Парткод: | B132 1504 |
| Деталь: | Cover:Right Lower |
| Парткод: | B1321508 |
| Деталь: | Connector cap |
| Парткод: | B065 1341 |
| Деталь: | Cover:Rear Lower:Assy |
| Парткод: | B132 1471 |
| Деталь: | Cover:Right Middle |
| Парткод: | B1321505 |
| Деталь: | G4 Cap |
| Парткод: | B065 1344 |
| Деталь: | LCT Cover |
| Парткод: | B065 1303 |
| Деталь: | Slide Rail:Toner Supply:Assy |
| Парткод: | AA07 0064 |
| Деталь: | Sheet:Stay |
| Парткод: | B132 6949 |
| Деталь: | Stay:Intermediate Transfer:Left |
| Парткод: | B1321003 |
| Деталь: | Duct:Fusing:Upper |
| Парткод: | B132 2426 |
| Деталь: | Duct:Imaging Unit:Exhaust:Assy |
| Парткод: | B132 6958 |
| Деталь: | Duct:Imaging Unit:Sub-assy |
| Парткод: | B132 6978 |
| Деталь: | Duct:Imaging Unit:1st:Assy |
| Парткод: | B132 6971 |
| Деталь: | Duct:Imaging Unit:Exhaust:Assy |
| Парткод: | B132 6965 |
| Деталь: | Cover:Duct:Imaging Unit:Assy |
| Парткод: | B132 6980 |
| Деталь: | Duct:Imaging Unit:23st:Assy |
| Парткод: | B132 6973 |
| Деталь: | Duct:Imaging Unit:4st:Assy |
| Парткод: | B132 6975 |
| Деталь: | Duct:Humidity Control:Assy |
| Парткод: | B132 2470 |
| Деталь: | Bracket:Exhaust:Harness |
| Парткод: | B132 6867 |
| Деталь: | Bracket:Hinge:Door |
| Парткод: | B132 1462 |
| Деталь: | Turret Spring |
| Парткод: | AA06 3052 |
| Деталь: | Hinge Shaft |
| Парткод: | A096 1355 |
| Деталь: | Screw: M4 |
| Парткод: | AA14 3545 |
| Деталь: | Duct:Fusing:Side:Assy |
| Парткод: | B132 6896 |
| Деталь: | Screw: Safety |
| Парткод: | AA14 3791 |
| Деталь: | Heat Pipe:Assy |
| Парткод: | B132 6884 |
| Деталь: | Duct:Fusing:Exit:Upper:Left |
| Парткод: | B132 6917 |
| Деталь: | Duct:Fusing:Exit:Upper |
| Парткод: | B132 6892 |
| Деталь: | Duct:Exit:Upper:Left:Assy |
| Парткод: | B132 6908 |
| Деталь: | Duct:Exit:Upper |
| Парткод: | B132 6912 |
| Деталь: | Decal - Y Toner Supply |
| Парткод: | GA00 3016 |
| Деталь: | Decal - C Toner Supply |
| Парткод: | GA00 3018 |
| Деталь: | Decal - M Toner Supply |
| Парткод: | GA00 3017 |
| Деталь: | Decal - K Toner Supply |
| Парткод: | GA00 3019 |
| Деталь: | Cover Oil Application Unit |
| Парткод: | B132 4178 |
| Деталь: | Guide Plate:Fusing Exit:Upper |
| Парткод: | B132 4174 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Grip:Oil Application Unit |
| Парткод: | B132 4168 |
| Деталь: | Lever:Oil Application Unit:Front |
| Парткод: | B132 4165 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2138 |
| Деталь: | Bracket:Oil Application Unit |
| Парткод: | B132 4160 |
| Деталь: | Shaft:Oil Application Unit |
| Парткод: | B132 4163 |
| Деталь: | TORSION SPRING:LEVER |
| Парткод: | B132 4197 |
| Деталь: | Lever:Oil Application Unit:Rear |
| Парткод: | B132 4164 |
| Деталь: | Compression Spring - 2.5n |
| Парткод: | B132 4191 |
| Деталь: | Bushing:Cleaning Roller |
| Парткод: | AE031057 |
| Деталь: | Oil Supply Roller |
| Парткод: | AE04 0062 |
| Деталь: | Hot Roller Cleaning Roller |
| Парткод: | AE04 2051 |
| Деталь: | Housing:Thermostat |
| Парткод: | B132 4148 |
| Деталь: | Bracket:Thermistor:Hot Roller |
| Парткод: | B132 4146 |
| Деталь: | Housing:Thermostat |
| Парткод: | B132 4153 |
| Деталь: | Bracket:Torsion Spring:Peen |
| Парткод: | B132 4127 |
| Деталь: | Torsion Spring:Oil Application Unit |
| Парткод: | B132 4195 |
| Деталь: | Stripper Pawls:Assy |
| Парткод: | B132 4258 |
| Деталь: | Stripper Pawl Stay |
| Парткод: | B132 4256 |
| Деталь: | Torsion Spring:Lever:Rear |
| Парткод: | B132 4190 |
| Деталь: | Spring Plate:Oil Application Unit |
| Парткод: | B132 4269 |
| Деталь: | Torsion Spring:Guide Plate |
| Парткод: | B132 4198 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Duct:Development:Front:Y |
| Парткод: | B132 2459 |
| Деталь: | Duct:Development:Front |
| Парткод: | B132 2458 |
| Деталь: | Seal:Fan Motor |
| Парткод: | B132 2485 |
| Деталь: | Fan Motor:MM40:15mm |
| Парткод: | AX64 0149 |
| Деталь: | Shield:Duct |
| Парткод: | B132 2474 |
| Деталь: | Duct:Toner Hopper |
| Парткод: | B132 2457 |
| Деталь: | Shield:Duct:Left |
| Парткод: | B132 2476 |
| Деталь: | Heat Insulation:Toner Supply Unit |
| Парткод: | B132 3246 |
| Деталь: | Cover:Lower:Color |
| Парткод: | B132 3230 |
| Деталь: | Toner Supply Unit:Assy |
| Парткод: | B132 3336 |
| Деталь: | Tube:Black |
| Парткод: | B132 3436 |
| Деталь: | Coil:Guard:Tube:Black |
| Парткод: | B132 3438 |
| Деталь: | Toner End Sensor |
| Парткод: | AW23 0009 |
| Деталь: | Tube:Color |
| Парткод: | B132 3437 |
| Деталь: | Coil:Guard:Tube:Color |
| Парткод: | B132 3439 |
| Деталь: | Seal:Duct:Toner Hopper:Lower |
| Парткод: | B132 2496 |
| Деталь: | Toner Supply Unit:Assy |
| Парткод: | B132 3202 |
| Деталь: | STAY |
| Парткод: | B132 3428 |
| Деталь: | Spring Plate:Stand |
| Парткод: | B132 3240 |
| Деталь: | Lever:Stand |
| Парткод: | B132 3239 |
| Деталь: | Shaft:Lever: Stand |
| Парткод: | B132 3216 |
| Деталь: | Spring Plate:Lever:Stand |
| Парткод: | B132 3242 |
| Деталь: | Guide Plate:Lever:Stand |
| Парткод: | B132 3241 |
| Деталь: | Inner Cover:Left |
| Парткод: | B132 3236 |
| Деталь: | Stand: Left |
| Парткод: | B132 3237 |
| Деталь: | Guide:Stand |
| Парткод: | B132 3238 |
| Деталь: | Guide:Arm:Stopper:Holder |
| Парткод: | B132 3323 |
| Деталь: | Arm:Stopper:Holder:Color |
| Парткод: | B132 3322 |
| Деталь: | Bracket:Stopper:Holder:Left:Assy |
| Парткод: | B132 3316 |
| Деталь: | Bracket:Stopper:Holder:Right:Assy |
| Парткод: | B132 3314 |
| Деталь: | Decal:Lever:Toner Supply:M |
| Парткод: | B132 3331 |
| Деталь: | Decal:Lever:Toner Supply:C |
| Парткод: | B132 3332 |
| Деталь: | Decal:Lever:Toner Supply:Y |
| Парткод: | B132 3333 |
| Деталь: | Holder:Toner Cartridge:Color:Assy |
| Парткод: | B132 3287 |
| Деталь: | Cover:Black |
| Парткод: | B132 3232 |
| Деталь: | Inner Cover:Right |
| Парткод: | B132 3235 |
| Деталь: | Cover:Lower:Holder:Y |
| Парткод: | B132 3254 |
| Деталь: | Cover:Lower:Holder:M |
| Парткод: | B132 3252 |
| Деталь: | Cover:Lower:Holder:C |
| Парткод: | B132 3253 |
| Деталь: | Cover:Color |
| Парткод: | B132 3233 |
| Деталь: | Sheet:Cover:Holder |
| Парткод: | B132 3234 |
| Деталь: | Arm:Stopper:Holder:Black |
| Парткод: | B132 3321 |
| Деталь: | Decal:Lever:Toner Supply:K |
| Парткод: | B132 3330 |
| Деталь: | Holder:Toner Cartridge:Black:Assy |
| Парткод: | B132 3286 |
| Деталь: | Cover:Lower:Holder:Black |
| Парткод: | B132 3251 |
| Деталь: | SHEET |
| Парткод: | B132 3245 |
| Деталь: | Knob:Front |
| Парткод: | B132 7008 |
| Деталь: | Decal:LED:E1 |
| Парткод: | B132 7130 |
| Деталь: | Decal:LED:D1 |
| Парткод: | B132 7131 |
| Деталь: | Knob Joint |
| Парткод: | A166 4290 |
| Деталь: | Fusing Unit Knob |
| Парткод: | AG05 1144 |
| Деталь: | Inner Cover:Pull Out:Left |
| Парткод: | B132 1198 |
| Деталь: | Lever:Release |
| Парткод: | B132 2716 |
| Деталь: | LED:Red:MU93-5001 |
| Парткод: | B132 7146 |
| Деталь: | Bracket: LED: Left |
| Парткод: | B132 7121 |
| Деталь: | Fan Motor:Assy |
| Парткод: | B132 6940 |
| Деталь: | Harness:Front:Fan |
| Парткод: | B132 5243 |
| Деталь: | Bracket:LED:Pull Out:Right |
| Парткод: | B1321239 |
| Деталь: | Lever:Pull Out:Printing |
| Парткод: | B1321184 |
| Деталь: | Inner Cover:Pull Out:Middle |
| Парткод: | B1321200 |
| Деталь: | Decal:Caution:Pull Out |
| Парткод: | B132 1238 |
| Деталь: | Duct:Fusing:Vacuum:Assy |
| Парткод: | B132 6931 |
| Деталь: | Fan Motor:Mm60 |
| Парткод: | AX64 0151 |
| Деталь: | Registration Roller Knob |
| Парткод: | A060 2512 |
| Деталь: | Inner Cover:Pull Out:Right |
| Парткод: | B132 1189 |
| Деталь: | Decal:Lever:B4 |
| Парткод: | B132 2709 |
| Деталь: | Seal:Duct:Upper |
| Парткод: | B132 6925 |
| Деталь: | Seal:Inner Cover:Lower |
| Парткод: | B132 6928 |
| Деталь: | Cover:Duct:Middle |
| Парткод: | B132 7150 |
| Деталь: | Bracket:Inner Cover:Pull Out:Left |
| Парткод: | B1321240 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Bracket:Paper Feed Sensor |
| Парткод: | B132 4284 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0118 |
| Деталь: | Guide Plate:Fusing Exit:Lower |
| Парткод: | B132 4283 |
| Деталь: | Pressure Roller Cleaning Felt Assy |
| Парткод: | B132 4075 |
| Деталь: | Holder:Lever:Pressure Roller |
| Парткод: | B132 4255 |
| Деталь: | Bushing:Cleaning Roller:Pressure:Upper |
| Парткод: | AE03 1060 |
| Деталь: | Bushing:Cleaning Roller:Pressure:Lower |
| Парткод: | AE031059 |
| Деталь: | Harness:Fusing Unit:No.1:100V |
| Парткод: | B132 5204 |
| Деталь: | Harness:Fusing Unit:No.1:200V |
| Парткод: | B132 5209 |
| Деталь: | Screw - Inner Cover |
| Парткод: | B004 5843 |
| Деталь: | Pressure Spring Holder |
| Парткод: | A030 4145 |
| Деталь: | Stripper Pawls:Assy |
| Парткод: | B132 4290 |
| Деталь: | Terminal:4P:187 |
| Парткод: | AA11 3037 |
| Деталь: | Bracket: Drawer |
| Парткод: | B132 4244 |
| Деталь: | SPRING |
| Парткод: | G003 5674 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE02 0144 |
| Деталь: | Gear:Lower:49z |
| Парткод: | AB01 3636 |
| Деталь: | BALL BEARING |
| Парткод: | AE03 0040 |
| Деталь: | Heater Holder:Lower |
| Парткод: | B132 4245 |
| Деталь: | Lever: Pressure |
| Парткод: | B132 4233 |
| Деталь: | Holder:Spring:Rear |
| Парткод: | B132 4230 |
| Деталь: | Lever:Release |
| Парткод: | B132 4238 |
| Деталь: | Lever:Turn |
| Парткод: | B132 4232 |
| Деталь: | Compression Spring:Pressure:300n |
| Парткод: | B132 4192 |
| Деталь: | Side Plate:Lower Rear |
| Парткод: | B132 4201 |
| Деталь: | Tension Spring:Heat Roller |
| Парткод: | B132 4193 |
| Деталь: | Stay:Lower |
| Парткод: | B132 4203 |
| Деталь: | Stay:Right Lower |
| Парткод: | B132 4204 |
| Деталь: | Housing:Thermostat |
| Парткод: | B132 4148 |
| Деталь: | Side Plate:Lower Front |
| Парткод: | B132 4202 |
| Деталь: | Holder:Spring:Front |
| Парткод: | B132 4231 |
| Деталь: | Harness:Thermostat:Lower Front |
| Парткод: | B132 4249 |
| Деталь: | Bracket:Connector |
| Парткод: | B132 4246 |
| Деталь: | Harness:Manual Feed:Stepper Motor |
| Парткод: | B132 5218 |
| Деталь: | Harness:DRB:IOB:Power Source |
| Парткод: | B132 5213 |
| Деталь: | Harness:Large Capacity Tray:DRB |
| Парткод: | B132 5216 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | B132 5211 |
| Деталь: | Harness:Drb:Safety Switch:Fan |
| Парткод: | B132 5383 |
| Деталь: | Harness:Duplex:DRB:Drawer |
| Парткод: | B132 5260 |
| Деталь: | PCB DRB |
| Парткод: | B132 5428 |
| Деталь: | PCB:DMB |
| Парткод: | B132 5425 |
| Деталь: | Harness:Drum:Motor:KM |
| Парткод: | B132 5267 |
| Деталь: | PCB:TMB |
| Парткод: | B132 5476 |
| Деталь: | Bracket:Power Pack |
| Парткод: | B132 5979 |
| Деталь: | Harness:Bank:Front:3way |
| Парткод: | B132 5395 |
| Деталь: | Harness:Bank:Rear:3way |
| Парткод: | B132 5396 |
| Деталь: | Harness:IOB:PP1 :pFC |
| Парткод: | B132 5381 |
| Деталь: | PCB:pFC |
| Парткод: | B132 5461 |
| Деталь: | Harness:Main |
| Парткод: | B132 5350 |
| Деталь: | Power Pack:C |
| Парткод: | AZ320136 |
| Деталь: | Bracket:DRV |
| Парткод: | B132 5862 |
| Деталь: | Case:Remove Paper Dust |
| Парткод: | B132 2605 |
| Деталь: | Bracket:Remove Paper Dust:Assy |
| Парткод: | B132 2601 |
| Деталь: | Bracket:Registration Sensor |
| Парткод: | B132 2620 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Harness:Pull Out:Uni:26pin |
| Парткод: | B132 5245 |
| Деталь: | Optics Sensor:Photo |
| Парткод: | AW00 0010 |
| Деталь: | Stay:Registration Guide |
| Парткод: | B132 2700 |
| Деталь: | Registration Guide:Upper |
| Парткод: | B132 2673 |
| Деталь: | Lever:Un Lock |
| Парткод: | B132 2671 |
| Деталь: | Bushing - 4x6x7mm |
| Парткод: | 54 432 668 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0957 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0962 |
| Деталь: | Side Plate:Open And Close:Front |
| Парткод: | B132 2674 |
| Деталь: | Shaft:Lock |
| Парткод: | B132 2670 |
| Деталь: | Lever: Knob:Release |
| Парткод: | B132 2644 |
| Деталь: | Registration Guide:Upper |
| Парткод: | B132 2682 |
| Деталь: | Shaft:Contact Point:Lever |
| Парткод: | B132 2681 |
| Деталь: | Knob:Release |
| Парткод: | B132 2651 |
| Деталь: | Registration Guide:Connecting |
| Парткод: | B132 2680 |
| Деталь: | Side Plate:Open And Close:Rear |
| Парткод: | B132 2669 |
| Деталь: | Cover:Drive Sub-unit |
| Парткод: | B132 1188 |
| Деталь: | Harness:Dehumidifier |
| Парткод: | B132 5265 |
| Деталь: | Screw: Drawer |
| Парткод: | AA14 3792 |
| Деталь: | Stud:Contact Point |
| Парткод: | B132 2703 |
| Деталь: | Seal:Remove Paper Dust |
| Парткод: | B132 2626 |
| Деталь: | Seal:Remove Paper Dust:Inner Back |
| Парткод: | B132 2627 |
| Деталь: | Seal:Optics Sensor:Middle |
| Парткод: | B132 2632 |
| Деталь: | Shoulder Screw - Front Cover |
| Парткод: | AA143129 |
| Деталь: | SPRING |
| Парткод: | AA062318 |
| Деталь: | Decal:Grip:E3 |
| Парткод: | B132 4796 |
| Деталь: | Lever:Open And Close:Reverse Unit |
| Парткод: | B132 4647 |
| Деталь: | Release Lever |
| Парткод: | AG05 1141 |
| Деталь: | Lower Entrance Guide Plate |
| Парткод: | A229 4623 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3579 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | Duplex Driven Roller |
| Парткод: | A229 4624 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | Side Plate:Front:Reverse Unit |
| Парткод: | B132 4627 |
| Деталь: | Tension Spring:Black |
| Парткод: | AA06 2328 |
| Деталь: | Entrance Inverter Roller |
| Парткод: | AF02 1074 |
| Деталь: | Spacer:Gate Pawl |
| Парткод: | B132 4643 |
| Деталь: | Front Gate Pawl |
| Парткод: | A293 4613 |
| Деталь: | Reverse Roller |
| Парткод: | A293 4611 |
| Деталь: | Rear Gate Pawl |
| Парткод: | A293 4614 |
| Деталь: | Side Plate:Rear:Reverse Unit:Assy |
| Парткод: | B132 4620 |
| Деталь: | Joint Holder |
| Парткод: | B065 4632 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3582 |
| Деталь: | Drive Joint |
| Парткод: | A229 4740 |
| Деталь: | Sensor bracket |
| Парткод: | B065 4644 |
| Деталь: | Duplex Discharge Brush |
| Парткод: | A229 4617 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0119 |
| Деталь: | Harness:Sensor:Reverse Unit |
| Парткод: | B132 4985 |
| Деталь: | Guide Plate:Entrance:Upper:Assy |
| Парткод: | B132 4640 |
| Деталь: | Stopped Screw - M4x17 |
| Парткод: | AA14 3426 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Shaft:Cleaner |
| Парткод: | AA14 3789 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | B301 1286 |
| Деталь: | Spacer - M6.5x1 |
| Парткод: | A418 1158 |
| Деталь: | Compression Spring:Paper FeedJoint |
| Парткод: | AA06 3435 |
| Деталь: | SPACER |
| Парткод: | AA13 2013 |
| Деталь: | Guide Plate Cushion |
| Парткод: | A806 1163 |
| Деталь: | Front Entrance Guide |
| Парткод: | B477 2172 |
| Деталь: | Feed-in Unit Stopper |
| Парткод: | A680 1621 |
| Деталь: | Bushing - 8mm |
| Парткод: | A628 1225 |
| Деталь: | Feed Belt Drive Roller |
| Парткод: | A8061293 |
| Деталь: | Separation Shaft |
| Парткод: | B477 2191 |
| Деталь: | Feed Belt |
| Парткод: | A806 1295 |
| Деталь: | SPRING BELT GUIDE ROLLER |
| Парткод: | A806 4261 |
| Деталь: | Feed Belt Driven Roller |
| Парткод: | A806 1294 |
| Деталь: | Transport Belt Roller Shaft |
| Парткод: | A8061298 |
| Деталь: | Feed Belt Bracket |
| Парткод: | A806 1292 |
| Деталь: | Rear Entrance Guide |
| Парткод: | B477 2182 |
| Деталь: | Pick-up Roller Lever |
| Парткод: | B477 2231 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Pickup Roller:Coupling |
| Парткод: | B477 2226 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | B477 2225 |
| Деталь: | Spacer - 6x20x1 |
| Парткод: | AA132171 |
| Деталь: | Timing Belt:B40S2M142 |
| Парткод: | B652 2213 |
| Деталь: | Timing Pulley:21T |
| Парткод: | B652 2212 |
| Деталь: | Guide:Paper Feed Belt:Front |
| Парткод: | B652 2215 |
| Деталь: | Pick-up Roller Bracket |
| Парткод: | B477 2222 |
| Деталь: | Timing Pulley - T19/Z23 S2M/M0.6 |
| Парткод: | A806 2151 |
| Деталь: | Gear - Z18 |
| Парткод: | A806 2271 |
| Деталь: | PCU-K |
| Парткод: | B132 2211 |
| Деталь: | PCU-CMY |
| Парткод: | B132 2212 |
| Деталь: | Electric Potential Sensor |
| Парткод: | B132 2344 |
| Деталь: | Joint PCU |
| Парткод: | B132 3600 |
| Деталь: | Positioning Plate:Cleaning |
| Парткод: | B132 2335 |
| Деталь: | Drum Stay:Rear |
| Парткод: | B132 3607 |
| Деталь: | OPC Drum |
| Парткод: | B132 9510 |
| Деталь: | Bushing:Brush Roller |
| Парткод: | B132 3655 |
| Деталь: | Bushing - 6x8x5 |
| Парткод: | AA08 2106 |
| Деталь: | Drum Cleaning Brush Assy |
| Парткод: | B132 3555 |
| Деталь: | Drum Stay:Front:Assy |
| Парткод: | B132 3601 |
| Деталь: | Drum Cleaning Blade |
| Парткод: | B132 3560 |
| Деталь: | Drum Charge Roller Assy |
| Парткод: | B132 2270 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW14 0012 |
| Деталь: | Stay:Temperature & Humidity Sensor |
| Парткод: | B132 2380 |
| Деталь: | Drum Lubricant Bar |
| Парткод: | B132 3573 |
| Деталь: | Ground Plate:Brush Roller |
| Парткод: | B132 3656 |
| Деталь: | Cleaning Brush Seal Rear |
| Парткод: | B132 3653 |
| Деталь: | Cleaning Brush Seal Front |
| Парткод: | B132 3654 |
| Деталь: | Discharge Lamp:LED Array |
| Парткод: | B132 2269 |
| Деталь: | Developer Cartridge Black |
| Парткод: | B200 9640 |
| Деталь: | Developer Cartridge Cyan |
| Парткод: | B200 9660 |
| Деталь: | Developer Cartridge Magenta |
| Парткод: | B200 9670 |
| Деталь: | Developer Cartridge Yellow |
| Парткод: | B200 9680 |
| Деталь: | Stay:Toner Catch |
| Парткод: | B132 3070 |
| Деталь: | Gear - 30Z |
| Парткод: | B132 3596 |
| Деталь: | Transport Screw |
| Парткод: | B132 3580 |
| Деталь: | Lubricant Bar Weight |
| Парткод: | B132 3574 |
| Деталь: | STEPPED SCREW |
| Парткод: | 54 472 769 |
| Деталь: | Paper Discharge Plate |
| Парткод: | B132 6268 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3716 |
| Деталь: | Stay:Brush Roller:Assy |
| Парткод: | B132 6253 |
| Деталь: | Stay:Transfer Unit |
| Парткод: | B132 6274 |
| Деталь: | Shaft:Contact Point |
| Парткод: | B132 6287 |
| Деталь: | Paper Transfer Roller |
| Парткод: | B132 6250 |
| Деталь: | Gear:40Z |
| Парткод: | B132 6303 |
| Деталь: | Spring:Pressure |
| Парткод: | B132 6306 |
| Деталь: | PTR Cleaning Brush |
| Парткод: | B132 6255 |
| Деталь: | Bushing:6x10x6 |
| Парткод: | AA08 2137 |
| Деталь: | Guide Plate:Entrance:Assy |
| Парткод: | B132 6295 |
| Деталь: | Shield:Guide Plate:Entrance |
| Парткод: | B132 6323 |
| Деталь: | PTR Lubricant Bar |
| Парткод: | B132 6289 |
| Деталь: | PTR Cleaning Blade |
| Парткод: | B132 6265 |
| Деталь: | Holder:Blade |
| Парткод: | B132 6269 |
| Деталь: | Spring:Blade |
| Парткод: | B132 6299 |
| Деталь: | Gear:40Z |
| Парткод: | B132 6301 |
| Деталь: | Joint:Transfer:Drive |
| Парткод: | B132 6284 |
| Деталь: | Gear:40Z |
| Парткод: | B132 6302 |
| Деталь: | Bracket:Gear: Idler |
| Парткод: | B132 6311 |
| Деталь: | Base:Transfer Roller:Rear:Assy |
| Парткод: | B132 6307 |
| Деталь: | Spring:Pressure |
| Парткод: | B132 6288 |
| Деталь: | Gear:21Z |
| Парткод: | AB01 1124 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Timing Belt:S2M170 |
| Парткод: | AA04 3587 |
| Деталь: | Pulley:23T |
| Парткод: | AB03 0749 |
| Деталь: | Supporting Plate:Pull Out |
| Парткод: | B132 1186 |
| Деталь: | Gear:20/29Z |
| Парткод: | AB01 1125 |
| Деталь: | Gear:20Z |
| Парткод: | AB01 1126 |
| Деталь: | Basefront |
| Парткод: | B132 6314 |
| Деталь: | Rear bushing |
| Парткод: | AA08 0154 |
| Деталь: | Spring:Tightener:Transport Screw |
| Парткод: | B132 6337 |
| Деталь: | Pulley:Belt Tensioner |
| Парткод: | A257 6112 |
| Деталь: | Tightener:Transfer:Transport Screw:Assy |
| Парткод: | B132 6331 |
| Деталь: | Side Plate:Positioning:Transfer:Fro |
| Парткод: | B132 6334 |
| Деталь: | Seal:Guide Plate:Entrance:Lower |
| Парткод: | B132 6327 |
| Деталь: | Seal:Side Plate:Rear |
| Парткод: | B132 6326 |
| Деталь: | Seal:Side Plate:Front |
| Парткод: | B132 6325 |
| Деталь: | Grip:Guide Plate:Upper |
| Парткод: | B132 7056 |
| Деталь: | Pawl:Guide Plate:Fix |
| Парткод: | B132 7044 |
| Деталь: | Shaft:Release:Guide Plate:Upper |
| Парткод: | B132 7052 |
| Деталь: | Spring:Tightener |
| Парткод: | AA06 3908 |
| Деталь: | Stopper:Pipe |
| Парткод: | B132 7105 |
| Деталь: | Guide Plate:Transport:Upper:Left |
| Парткод: | B132 7016 |
| Деталь: | Spring Plate:Upper:Right |
| Парткод: | B132 7013 |
| Деталь: | Roller:Middle |
| Парткод: | B132 7031 |
| Деталь: | Bushing:DIA6 |
| Парткод: | AA08 0213 |
| Деталь: | Guide Plate:Transport:Upper:Right |
| Парткод: | B132 7010 |
| Деталь: | Sound Proofing Material |
| Парткод: | B132 7124 |
| Деталь: | Guide Plate:Entrance:Upper |
| Парткод: | B132 7129 |
| Деталь: | Guide:Entrance:Right Front |
| Парткод: | B132 7164 |
| Деталь: | Decura:Heat Pipe:DIA15 |
| Парткод: | B132 7005 |
| Деталь: | Bracket:Positioning Plate:Rear |
| Парткод: | B132 7133 |
| Деталь: | Bushing - MM5 |
| Парткод: | AA08 0240 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3906 |
| Деталь: | Supporting Plate:Pull Out:Front |
| Парткод: | B132 1159 |
| Деталь: | Shaft:Knob |
| Парткод: | B132 7037 |
| Деталь: | Gear:28Z |
| Парткод: | B132 7002 |
| Деталь: | Bracket: Lever |
| Парткод: | B132 7007 |
| Деталь: | Holder:Bearing:Front |
| Парткод: | B132 7011 |
| Деталь: | Bracket:Bearing:Front |
| Парткод: | B132 7039 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | DC Motor:Drive:Transfer |
| Парткод: | B1321330 |
| Деталь: | DC Motor:On-off:Assy |
| Парткод: | B1321338 |
| Деталь: | Collar:Joint:Drive |
| Парткод: | B132 2488 |
| Деталь: | Joint:Drive:K |
| Парткод: | B132 2487 |
| Деталь: | Joint:Drive |
| Парткод: | B132 2486 |
| Деталь: | Drum Shaft:K |
| Парткод: | B132 2491 |
| Деталь: | Drum Shaft |
| Парткод: | B132 2481 |
| Деталь: | Bracket: On-Off: Plate |
| Парткод: | B1321339 |
| Деталь: | DC Motor:Drum:DIA87:Assy |
| Парткод: | B132 2493 |
| Деталь: | Stud: Drive: Motor: Drum |
| Парткод: | B132 1264 |
| Деталь: | DC Motor:MM63:24W |
| Парткод: | AX06 0280 |
| Деталь: | Bracket: Drive |
| Парткод: | B1321260 |
| Деталь: | Gear:Pulley:60Z/36T |
| Парткод: | AB01 7681 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0950 |
| Деталь: | Bracket:Tightener:Drive |
| Парткод: | B132 1266 |
| Деталь: | Timing Pulley:44t |
| Парткод: | AB03 0767 |
| Деталь: | Timing Belt:60S2M396 |
| Парткод: | AA04 3963 |
| Деталь: | Pulley:Idler |
| Парткод: | B132 1282 |
| Деталь: | Timing Pulley:37T |
| Парткод: | AB03 0766 |
| Деталь: | Shaft:Drive:Brush Roller:Assy |
| Парткод: | B1321275 |
| Деталь: | Shaft:Drive:Development:Assy |
| Парткод: | B132 1270 |
| Деталь: | Bracket:Auxiliary:Drive |
| Парткод: | B1321265 |
| Деталь: | Seal:Duct:Side Plate:Rear:Rear |
| Парткод: | B132 2467 |
| Деталь: | Duct:Side Plate:Rear:Rear |
| Парткод: | B132 2421 |
| Деталь: | Duct:Side Plate:Rear:Front |
| Парткод: | B132 2420 |
| Деталь: | Gear:32Z |
| Парткод: | AB01 1301 |
| Деталь: | Guard:Pull Out |
| Парткод: | B132 1192 |
| Деталь: | Guide Plate:Paper Bank:Assy |
| Парткод: | B132 2767 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0203 |
| Деталь: | Transport Roller:Driven |
| Парткод: | B132 2639 |
| Деталь: | Driven Roller Spring |
| Парткод: | AA06 3254 |
| Деталь: | Guide Plate:Connecting:Right Upper |
| Парткод: | B132 2636 |
| Деталь: | HARNESS:SENSOR |
| Парткод: | B132 5247 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Bracket:Sensor |
| Парткод: | B132 2773 |
| Деталь: | DC Solenoid:24V:16.5W:Assy |
| Парткод: | B132 2594 |
| Деталь: | Arm:Guide |
| Парткод: | B132 2649 |
| Деталь: | Arm:Perpendicular |
| Парткод: | B132 2650 |
| Деталь: | Support Stay:Solenoid |
| Парткод: | B132 2753 |
| Деталь: | Bracket:Solenoid |
| Парткод: | B132 2661 |
| Деталь: | Rail:Solenoid:Release |
| Парткод: | B132 2667 |
| Деталь: | Cover:Motor:Registration |
| Парткод: | B132 2723 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Bracket:Tightener |
| Парткод: | B132 2720 |
| Деталь: | TENSION SPRING |
| Парткод: | B132 2710 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B132 2711 |
| Деталь: | Timing Belt:60S2M138 |
| Парткод: | AA04 3312 |
| Деталь: | Stepper Motor:Registration:Assy |
| Парткод: | B132 2722 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket:Photointerruptor |
| Парткод: | B1321233 |
| Деталь: | Guide:Duplex:Upper Right |
| Парткод: | B132 4868 |
| Деталь: | Harness:Paper Exit Unit |
| Парткод: | B132 5244 |
| Деталь: | Bracket:Sensor |
| Парткод: | B132 7049 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Cover: Exhaust |
| Парткод: | B132 7023 |
| Деталь: | Discharge Brush |
| Парткод: | AA12 0084 |
| Деталь: | Stay:Exit:Assy |
| Парткод: | B132 7018 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3577 |
| Деталь: | Ball Bearing:Driven:MM4 |
| Парткод: | AA08 4053 |
| Деталь: | Exit Roller:Driven:Upper |
| Парткод: | B132 7147 |
| Деталь: | Shaft:Lever:Left Inner Rear |
| Парткод: | B132 7123 |
| Деталь: | Lever:Stopper |
| Парткод: | B132 7041 |
| Деталь: | SPRING |
| Парткод: | AA06 2319 |
| Деталь: | Lever:Open And Close |
| Парткод: | B132 7042 |
| Деталь: | Bracket: Stay: Left |
| Парткод: | B132 7119 |
| Деталь: | Bracket: Fix: Front |
| Парткод: | B132 7043 |
| Деталь: | Duct:Pull Out |
| Парткод: | B132 2463 |
| Деталь: | Seal:Duct:Pull Out |
| Парткод: | B132 2484 |
| Деталь: | Cover:Base:Pull Out |
| Парткод: | B1321220 |
| Деталь: | Harness:Pull Out:Uni:39pin |
| Парткод: | B132 5242 |
| Деталь: | Harness:High Voltage Supply Cord |
| Парткод: | B132 5356 |
| Деталь: | Power Pack:D |
| Парткод: | AZ31 0029 |
| Деталь: | Insulating Sheet:Pull Out |
| Парткод: | B1321228 |
| Деталь: | Knob Screw |
| Парткод: | 54131875 |
| Деталь: | Handle:Pull Out |
| Парткод: | B132 1191 |
| Деталь: | Shaft:Lock:Pull Out |
| Парткод: | B132 1185 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3951 |
| Деталь: | Cam:Transfer Roller |
| Парткод: | B132 6305 |
| Деталь: | Toner Catchpan |
| Парткод: | B132 6285 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | A267 5814 |
| Деталь: | Holder:Spring:Pull Out |
| Парткод: | B132 1221 |
| Деталь: | Bracket:Release:Lock |
| Парткод: | B132 1190 |
| Деталь: | Roller:Lock:Pull Out |
| Парткод: | AA13 2300 |
| Деталь: | Bracket: Lock |
| Парткод: | B132 1183 |
| Деталь: | Supporting Plate:Bracket:Lock |
| Парткод: | B132 1224 |
| Деталь: | Bracket: Fix: Rear |
| Парткод: | B132 7050 |
| Деталь: | Shaft:Stopper |
| Парткод: | B132 7096 |
| Деталь: | Holder:Shaft |
| Парткод: | B132 7070 |
| Деталь: | Bracket:Interlock:Lever |
| Парткод: | B132 1193 |
| Деталь: | Actuator:Pull Out |
| Парткод: | B132 1194 |
| Деталь: | Bracket:Drawer:Pull Out |
| Парткод: | B132 1195 |
| Деталь: | Guide Plate:Fusing Unit |
| Парткод: | B132 1155 |
| Деталь: | Bracket:Knob:Fusing/paper Exit Unit |
| Парткод: | B132 1152 |
| Деталь: | Gear:18Z |
| Парткод: | AB01 3309 |
| Деталь: | Gear:13/20Z |
| Парткод: | AB01 7688 |
| Деталь: | Gear - 16Z |
| Парткод: | AB01 3363 |
| Деталь: | Shaft:Knob:Fusing/Paper Exit Unit |
| Парткод: | B132 1156 |
| Деталь: | Collar:DIA18 |
| Парткод: | B1321235 |
| Деталь: | Guide Plate - Upper Heat Sink |
| Парткод: | A248 6103 |
| Деталь: | Heater:115V:18W:Upper |
| Парткод: | AX40 0176 |
| Деталь: | Heater:240V:18W:Upper |
| Парткод: | AX40 0178 |
| Деталь: | Heat Sink:Heater:Upper:Fiber |
| Парткод: | B070 6293 |
| Деталь: | Supporting Plate:Stay |
| Парткод: | B132 6669 |
| Деталь: | Slide Rail:Tandem LCT |
| Парткод: | AA07 0072 |
| Деталь: | Slidebracket |
| Парткод: | B065 6774 |
| Деталь: | Stay:Tandem LCT:Assy |
| Парткод: | B132 6696 |
| Деталь: | Rail:Tandem LCT:Left:Assy |
| Парткод: | B132 7590 |
| Деталь: | Left Rail Bracket |
| Парткод: | B132 6742 |
| Деталь: | Lock Arm - Tandem Tray |
| Парткод: | B065 6135 |
| Деталь: | SPRING |
| Парткод: | AA06 0761 |
| Деталь: | Side Plate:Front:Paper Bank |
| Парткод: | B132 6689 |
| Деталь: | Rail:Paper Tray:Assy |
| Парткод: | B132 7591 |
| Деталь: | Seal - Misfeed Removal |
| Парткод: | AA15 0406 |
| Деталь: | Bracket: Holder: Assy |
| Парткод: | B132 6630 |
| Деталь: | Decal:Main Switch Display:On (NA) |
| Парткод: | B1321553 |
| Деталь: | Decal - Main Switch Display:Off (NA) |
| Парткод: | B1321555 |
| Деталь: | Inner Cover:Main Switch |
| Парткод: | B132 1551 |
| Деталь: | Shaft:Micro Switch:Front |
| Парткод: | B132 5855 |
| Деталь: | Lever:Micro Switch |
| Парткод: | B132 5853 |
| Деталь: | Safety switch spring |
| Парткод: | A2571165 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 1012 |
| Деталь: | Bracket:Main Switch |
| Парткод: | B132 5851 |
| Деталь: | Screw:Micro Switch |
| Парткод: | B132 5852 |
| Деталь: | Duct:Main:Vacuum:Assy |
| Парткод: | B132 6876 |
| Деталь: | Fan Motor:Mm60 |
| Парткод: | AX64 0151 |
| Деталь: | Duct:Main:Heat Sinker:Assy |
| Парткод: | B132 6871 |
| Деталь: | Humidity Control:Assy |
| Парткод: | B132 2409 |
| Деталь: | Seal:Fan:Humidity Control |
| Парткод: | B132 2465 |
| Деталь: | Fan Motor:MM60:25mm:24V |
| Парткод: | AX64 0150 |
| Деталь: | FILTER |
| Парткод: | B132 2468 |
| Деталь: | Humidity Control:Assy |
| Парткод: | B132 2410 |
| Деталь: | Duct:Imaging Unit:Rear:Assy |
| Парткод: | B132 6926 |
| Деталь: | Duct:Imaging Unit:Front:Assy |
| Парткод: | B132 6921 |
| Деталь: | Fan Motor:15mm:24V |
| Парткод: | AX64 0164 |
| Деталь: | Bracket:Connector |
| Парткод: | B132 2489 |
| Деталь: | Bracket:Drawer:Toner Supply |
| Парткод: | B132 3489 |
| Деталь: | Cover:Drawer |
| Парткод: | B132 3491 |
| Деталь: | Bracket:Fix:Toner Supply |
| Парткод: | B132 3493 |
| Деталь: | Duct:Vacuum:Entrance |
| Парткод: | B132 6855 |
| Деталь: | Duct:Vacuum:Assy |
| Парткод: | B132 6851 |
| Деталь: | Development Unit |
| Парткод: | B132 3080 |
| Деталь: | Gear:Development Roller |
| Парткод: | B132 3120 |
| Деталь: | Gear -21Z |
| Парткод: | B132 3118 |
| Деталь: | Gear - 19/27Z |
| Парткод: | B132 3123 |
| Деталь: | Gear - 27Z |
| Парткод: | B132 3124 |
| Деталь: | DENSITY SENSOR |
| Парткод: | B132 3199 |
| Деталь: | Cover:Gear:Assy |
| Парткод: | B132 3155 |
| Деталь: | Case:Developer:Upper |
| Парткод: | B132 3086 |
| Деталь: | Drum Stay:PCU:Rear |
| Парткод: | B132 2329 |
| Деталь: | Drum Stay:PCU:Front |
| Парткод: | B132 2328 |
| Деталь: | Adjusting Pin:Magnetic Roller |
| Парткод: | B132 3159 |
| Деталь: | Cover:Manual Feed:Machine or Copier |
| Парткод: | B132 2816 |
| Деталь: | Decal - Inkjet:Manual Feed |
| Парткод: | B132 1482 |
| Деталь: | Manual Feed Table:Assy |
| Парткод: | B132 2809 |
| Деталь: | Side Fence:Auxiliary:Front |
| Парткод: | B132 2863 |
| Деталь: | Side Fence:Auxiliary:Rear |
| Парткод: | B132 2866 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B132 2861 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B132 2864 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | B132 2875 |
| Деталь: | Guide:Manual Feed Table |
| Парткод: | B132 2868 |
| Деталь: | Rear Rack |
| Парткод: | A232 6083 |
| Деталь: | Gear - 16Z |
| Парткод: | G011 3305 |
| Деталь: | Paper size sensor |
| Парткод: | B132 2873 |
| Деталь: | Imaging Unit |
| Парткод: | B1321950 |
| Деталь: | PCB:Sync Detector Board:Side |
| Парткод: | B132 5185 |
| Деталь: | Door Stopper |
| Парткод: | A2591258 |
| Деталь: | Decal - LD 655 |
| Парткод: | AA00 0217 |
| Деталь: | Cover:Polygon Motor:Assy |
| Парткод: | B132 2185 |
| Деталь: | Polygon Motor |
| Парткод: | B132 2156 |
| Деталь: | Positioning Pin |
| Парткод: | B132 1971 |
| Деталь: | Harness:LDB:LDD |
| Парткод: | B132 5366 |
| Деталь: | Cover:Upper:Sub-assy |
| Парткод: | B132 2172 |
| Деталь: | Harness:Imaging Unit |
| Парткод: | B132 5226 |
| Деталь: | Shield:Shield Glass |
| Парткод: | B132 2085 |
| Деталь: | Grip:Shield Glass |
| Парткод: | B132 2094 |
| Деталь: | Shield Glass |
| Парткод: | AC01 5041 |
| Деталь: | Rail:Shield Glass |
| Парткод: | B132 2093 |
| Деталь: | Thermistor Plate |
| Парткод: | G060 1908 |
| Деталь: | Thermistor:Imaging Unit |
| Парткод: | AW10 0100 |
| Деталь: | Cable:LVDS:LDB |
| Парткод: | B132 5367 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Guide Plate:Lower:Pull Out |
| Парткод: | B652 2152 |
| Деталь: | Decal:Guide Plate:Reverse:Exit |
| Парткод: | B652 4119 |
| Деталь: | Guide Plate:Reverse:Exit:Upper |
| Парткод: | B652 4114 |
| Деталь: | Guide:Reverse:Exit |
| Парткод: | B652 4116 |
| Деталь: | Guide:Reverse:Exit:Middle |
| Парткод: | B652 4117 |
| Деталь: | Guide Plate:Reverse:Middle:Upper |
| Парткод: | B652 4115 |
| Деталь: | Guide Plate:Reverse:Entrance |
| Парткод: | B652 4103 |
| Деталь: | Reverse Roller:Exit:Drive |
| Парткод: | B652 4152 |
| Деталь: | EXIT ROLLER |
| Парткод: | B652 4726 |
| Деталь: | Paper Feed Sensor Bracket |
| Парткод: | B477 2495 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Harness:Sensor:Exit |
| Парткод: | B652 5461 |
| Деталь: | Guide:Scanning:Exit:Long |
| Парткод: | B652 4506 |
| Деталь: | Guide:Scanning:Exit:Short |
| Парткод: | B652 4507 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Guide:Scanning:Exit:Exit |
| Парткод: | B652 4501 |
| Деталь: | Discharge Brush:Exit:L37 |
| Парткод: | B652 4503 |
| Деталь: | Discharge Brush:Exit:L16 |
| Парткод: | B652 4504 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50 530 447 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A859 2230 |
| Деталь: | Timing Pulley:44t |
| Парткод: | B652 4727 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Timing Pulley - T28 S2M |
| Парткод: | A806 2111 |
| Деталь: | PIN |
| Парткод: | C1051866 |
| Деталь: | Guide Bracket |
| Парткод: | B477 2145 |
| Деталь: | Shield:Duct:Intermediate Transfer |
| Парткод: | B132 2450 |
| Деталь: | Duct:Drum Stay |
| Парткод: | B132 2442 |
| Деталь: | Duct:Drum Stay:PCU |
| Парткод: | B132 2423 |
| Деталь: | Inner Cover:Drum Stay |
| Парткод: | B132 2399 |
| Деталь: | Filter:Duct:Intermediate Transfer |
| Парткод: | B132 2466 |
| Деталь: | Duct:Intermediate Transfer |
| Парткод: | B132 2454 |
| Деталь: | Fan Motor:MM40:15mm |
| Парткод: | AX64 0149 |
| Деталь: | Harness:Sensor:Fan Motor |
| Парткод: | B132 5232 |
| Деталь: | Plate:Lever |
| Парткод: | B132 2365 |
| Деталь: | Lever:Drum Stay:Left |
| Парткод: | B132 2366 |
| Деталь: | Side Plate Lever |
| Парткод: | A257 3441 |
| Деталь: | Drum Stay |
| Парткод: | B132 2318 |
| Деталь: | Heat Insulation:Drum Stay |
| Парткод: | B132 2388 |
| Деталь: | Seal:Drum Stay:Lower |
| Парткод: | B132 2417 |
| Деталь: | Registration Roller:Upper |
| Парткод: | B132 2629 |
| Деталь: | Registration Roller:Lower |
| Парткод: | B132 2617 |
| Деталь: | LED:Radiate |
| Парткод: | AX56 0011 |
| Деталь: | Harness:LED:Sensor |
| Парткод: | B132 5246 |
| Деталь: | Bracket:Optics Sensor |
| Парткод: | B132 2624 |
| Деталь: | Registration Guide:Lower |
| Парткод: | B132 2610 |
| Деталь: | Ball Bearing - 8x12x5 |
| Парткод: | A247 2800 |
| Деталь: | Spacer - 1x8x12 |
| Парткод: | AA13 2025 |
| Деталь: | Timing Pulley:35T |
| Парткод: | AB03 0302 |
| Деталь: | Pawl:Lock:Front |
| Парткод: | B132 2708 |
| Деталь: | Bushing - 4x6x7mm |
| Парткод: | 54 432 668 |
| Деталь: | Shaft:Lock |
| Парткод: | B132 2691 |
| Деталь: | Pawl:Lock:Rear |
| Парткод: | B132 2692 |
| Деталь: | SPRING |
| Парткод: | AA06 6372 |
| Деталь: | Bushing - M8 |
| Парткод: | AA08 2116 |
| Деталь: | Roller:Connecting:Drive |
| Парткод: | B132 2658 |
| Деталь: | Guide Plate:Entrance:Lower Left |
| Парткод: | B132 2790 |
| Деталь: | EXIT ROLLER SPRING |
| Парткод: | AA06 3433 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA08 0034 |
| Деталь: | Transport Roller:Driven:Duplex |
| Парткод: | B132 2675 |
| Деталь: | Front Bushing - Registration |
| Парткод: | G020 2780 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2304 |
| Деталь: | Collar - 8mm |
| Парткод: | 54 462 901 |
| Деталь: | Cover:Harness:Pull Out |
| Парткод: | B132 1232 |
| Деталь: | Rear Bushing - Registration Roller |
| Парткод: | G020 2781 |
| Деталь: | Gear:50Z |
| Парткод: | AB01 1300 |
| Деталь: | Guide Plate:Open And Close:Middle |
| Парткод: | B132 2641 |
| Деталь: | Guide:Paper Feed:Upper |
| Парткод: | B477 2342 |
| Деталь: | Decal:Misfeed Removal:Paper Feed |
| Парткод: | B652 1811 |
| Деталь: | Decal:Display Guidance |
| Парткод: | B652 1812 |
| Деталь: | Decal:Size:Original |
| Парткод: | B652 1807 |
| Деталь: | Paper Feed Cover Grip |
| Парткод: | B477 1821 |
| Деталь: | Paper Feed Release Lever |
| Парткод: | B4771825 |
| Деталь: | SPRING |
| Парткод: | B477 4117 |
| Деталь: | Grip Shaft |
| Парткод: | B4771831 |
| Деталь: | Bracket:Pressure:Pickup |
| Парткод: | B652 1822 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 1824 |
| Деталь: | Pressure Plate:Pickup |
| Парткод: | B652 1823 |
| Деталь: | Rear Cover Bracket |
| Парткод: | B477 1851 |
| Деталь: | Front Cover Bracket |
| Парткод: | B477 1841 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | Paper feed Cover |
| Парткод: | B477 1791 |
| Деталь: | Pull Out Roller Bracket |
| Парткод: | B477 2361 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B477 2491 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0037 |
| Деталь: | SPRING |
| Парткод: | B477 4111 |
| Деталь: | Driven Pull Out Roller |
| Парткод: | B477 2351 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | A697 2131 |
| Деталь: | Bracket:Paper Size Sensor |
| Парткод: | B652 2523 |
| Деталь: | Photointerruptor:Paper Size Sensor: |
| Парткод: | AW02 0155 |
| Деталь: | Ph oto i nte rru pto r: E ntra n ce |
| Парткод: | AW02 0154 |
| Деталь: | Harness:Paper Size Sensor |
| Парткод: | B652 5411 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Harness:Sensor:Stopper Guide |
| Парткод: | B652 5416 |
| Деталь: | Relay Roller Arm |
| Парткод: | B477 2373 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 2505 |
| Деталь: | Driven Paper Feed Roller |
| Парткод: | B477 2372 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Cam:On-Off |
| Парткод: | B132 6111 |
| Деталь: | Shaft:Cam:Color |
| Парткод: | B132 6112 |
| Деталь: | Shaft:Positioning |
| Парткод: | B132 6094 |
| Деталь: | Roller:Opposed:Belt Cleaning |
| Парткод: | B132 6065 |
| Деталь: | Roller:Opposed |
| Парткод: | B132 6073 |
| Деталь: | Roller:T ransfer:Front |
| Парткод: | B132 6069 |
| Деталь: | Roller:Drive |
| Парткод: | B132 6055 |
| Деталь: | Shaft:Cam |
| Парткод: | B132 6113 |
| Деталь: | Cam:On-Off:Black |
| Парткод: | B132 6114 |
| Деталь: | Gear:16z |
| Парткод: | B132 6130 |
| Деталь: | Holder:Opposed:Rear:Assy |
| Парткод: | B132 6150 |
| Деталь: | Joint:Transfer:Drive |
| Парткод: | B132 6099 |
| Деталь: | Holder:Opposed:Transfer:Front |
| Парткод: | B132 6143 |
| Деталь: | Grip:On-Off |
| Парткод: | B132 6131 |
| Деталь: | Joint:Intermediate Transfer:Front:Assy |
| Парткод: | B132 6175 |
| Деталь: | Compression Spring:Plate:Intermedia |
| Парткод: | B132 6136 |
| Деталь: | Plate:Intermediate Transfer:Front |
| Парткод: | B132 6134 |
| Деталь: | Bracket:Fix:C/T Box:Lower:Auxiliary |
| Парткод: | B132 5912 |
| Деталь: | Bracket:Fix:C/T Box:Lower |
| Парткод: | B132 5911 |
| Деталь: | Bracket:Power Pack:Fix:Upper |
| Парткод: | B132 5980 |
| Деталь: | Bracket:Power Pack:Fix:Lower |
| Парткод: | B132 5981 |
| Деталь: | Harness:Shielded Wire:MB |
| Парткод: | B132 5214 |
| Деталь: | Harness:Dc Power Supply:Main |
| Парткод: | B132 5210 |
| Деталь: | Power Supply Unit:100V |
| Парткод: | AZ25 0018 |
| Деталь: | Power Supply Unit:200V |
| Парткод: | AZ25 0020 |
| Деталь: | Bracket:Power Supply Unit:Fix:Left |
| Парткод: | B132 5978 |
| Деталь: | Harness:AC Drive:DC Power Supply |
| Парткод: | B132 5202 |
| Деталь: | Harness:Leak Breaker:AC Drive |
| Парткод: | B132 5201 |
| Деталь: | Bracket:Leak Breaker:Rear |
| Парткод: | B132 5990 |
| Деталь: | Power Supply Cord:Stopper:NA |
| Парткод: | B132 5361 |
| Деталь: | Power Supply Cord:Stopper:EU |
| Парткод: | B132 5362 |
| Деталь: | Stopper:Power Supply Cord |
| Парткод: | B132 5995 |
| Деталь: | Bracket:Power Supply Cord:EXP |
| Парткод: | B132 5994 |
| Деталь: | Bracket:Leak Breaker |
| Парткод: | B132 5985 |
| Деталь: | Bracket:AC Drive Board:Welding |
| Парткод: | B132 5810 |
| Деталь: | Harness:Fusing:100V:C1a (B132) |
| Парткод: | B132 5371 |
| Деталь: | AC Control Board:100V |
| Парткод: | B132 5530 |
| Деталь: | AC Control Board:200V |
| Парткод: | B132 5532 |
| Деталь: | Harness:AC Drive Board |
| Парткод: | B132 5380 |
| Деталь: | Harness:Bank:Dehumidifier |
| Парткод: | B132 5392 |
| Деталь: | Harness :AC:Main:Switch |
| Парткод: | B132 5200 |
| Деталь: | Rail - Side Fence |
| Парткод: | G564 4151 |
| Деталь: | Table Side Fence |
| Парткод: | B477 2272 |
| Деталь: | Side Fence Pad |
| Парткод: | A376 4599 |
| Деталь: | Original Sensor Feeler Stud |
| Парткод: | B477 2286 |
| Деталь: | Original Sensor Feeler |
| Парткод: | A806 1351 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Base:Original Table:Assy |
| Парткод: | B652 2351 |
| Деталь: | Decal:Base:Original |
| Парткод: | B652 2354 |
| Деталь: | Harness:Original Sensor |
| Парткод: | B652 5451 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Original Sensor Bracket |
| Парткод: | B477 2281 |
| Деталь: | Photo Refiection Sensor:Original Table |
| Парткод: | AW01 0112 |
| Деталь: | Shaft:Rise:Base |
| Парткод: | B652 2333 |
| Деталь: | Bushing - 8mm |
| Парткод: | A628 1225 |
| Деталь: | Lever:Rise:Base |
| Парткод: | B652 2334 |
| Деталь: | Bracket: Lever: Rise: Base |
| Парткод: | B652 2335 |
| Деталь: | Shaft:Base:Rear:Assy |
| Парткод: | B652 2363 |
| Деталь: | Arm:Roller:Reverse:Upper |
| Парткод: | B652 2403 |
| Деталь: | Pressure Roller - Reverse |
| Парткод: | B351 3752 |
| Деталь: | Compression Spring:3.1n |
| Парткод: | B652 2404 |
| Деталь: | Bushing - 8mm |
| Парткод: | 50 530 223 |
| Деталь: | Ground Plate:Shaft:Base |
| Парткод: | B652 2323 |
| Деталь: | Bushing:Original Table |
| Парткод: | B652 2375 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Discharge Brush |
| Парткод: | A859 3225 |
| Деталь: | Stopper:Original Table |
| Парткод: | B652 2392 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 2393 |
| Деталь: | Guide Plate:Reverse:Upper |
| Парткод: | B652 2322 |
| Деталь: | Snap Ring |
| Парткод: | C101 2360 |
| Деталь: | Gear - Z47 |
| Парткод: | A806 2281 |
| Деталь: | Shaft:Cleaner |
| Парткод: | AA14 3789 |
| Деталь: | Original Table:Face Front:Printing |
| Парткод: | B652 2372 |
| Деталь: | Original Table:Behind |
| Парткод: | B652 2383 |
| Деталь: | Harness:Sensor:Original Table |
| Парткод: | B652 5436 |
| Деталь: | DC Solenoid:End Fence:Front:Assy |
| Парткод: | B132 7547 |
| Деталь: | Hook - Tension Sprong |
| Парткод: | A248 6713 |
| Деталь: | Tension Spring - Long |
| Парткод: | AA06 0757 |
| Деталь: | End Fence:Front:Adhesion |
| Парткод: | B132 7589 |
| Деталь: | Front Support Bracket |
| Парткод: | A294 6722 |
| Деталь: | End Fence:Rear |
| Парткод: | B132 7556 |
| Деталь: | Rear Support Bracket |
| Парткод: | A294 6723 |
| Деталь: | DC Solenoid:End Fence:Rear:Assy |
| Парткод: | B132 7571 |
| Деталь: | Right Rear Side Plate |
| Парткод: | A294 6676 |
| Деталь: | Sensor bracket |
| Парткод: | A294 6721 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Sheet - Photointerrupter |
| Парткод: | A267 1820 |
| Деталь: | Wire Ring |
| Парткод: | A248 6694 |
| Деталь: | Stay -rightbase |
| Парткод: | B065 6870 |
| Деталь: | End Fence Cover Front |
| Парткод: | B070 6667 |
| Деталь: | Tension Spring - Short |
| Парткод: | AA06 0758 |
| Деталь: | Lever:Release:Front |
| Парткод: | B070 6683 |
| Деталь: | Sensor bracket |
| Парткод: | A294 6720 |
| Деталь: | Wire Pulley - M10 |
| Парткод: | AB03 2058 |
| Деталь: | Guide - Pulley |
| Парткод: | A248 6695 |
| Деталь: | Pulley - M10 |
| Парткод: | AB032719 |
| Деталь: | Cover:Pulley:Drive Were |
| Парткод: | B132 7550 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 3781 |
| Деталь: | Bushing - 8mm |
| Парткод: | 50 530 223 |
| Деталь: | Oil Damper Bracket |
| Парткод: | B065 6872 |
| Деталь: | OIL DAMPER |
| Парткод: | A248 6701 |
| Деталь: | Side Plate:Tandem:Right Front |
| Парткод: | B070 6668 |
| Деталь: | Front Roller - Slide Rail |
| Парткод: | A294 6655 |
| Деталь: | Cushion - Small |
| Парткод: | AA16 1130 |
| Деталь: | Feeler - Paper Height Sensor |
| Парткод: | A294 6690 |
| Деталь: | Small Lever |
| Парткод: | B065 6864 |
| Деталь: | Roller - Slide Rail |
| Парткод: | AF02 2105 |
| Деталь: | Spacer - 6mm |
| Парткод: | AA13 2203 |
| Деталь: | Large Lever |
| Парткод: | B065 6862 |
| Деталь: | Lever:Release:Rear |
| Парткод: | B070 6684 |
| Деталь: | Cushion - Large |
| Парткод: | AA16 1129 |
| Деталь: | SENSOR |
| Парткод: | AW01 0113 |
| Деталь: | Bracket:Connector:Tandem LCT |
| Парткод: | B132 7575 |
| Деталь: | DC Harness - Tandem LCT |
| Парткод: | B070 5474 |
| Деталь: | Right Drive Shaft |
| Парткод: | A248 6687 |
| Деталь: | Entrance Scanning Guide |
| Парткод: | B477 2581 |
| Деталь: | SPRING |
| Парткод: | B477 4115 |
| Деталь: | Driven Entrance Scanning Roller |
| Парткод: | B477 2577 |
| Деталь: | Bushing- 4x8x4.5mm |
| Парткод: | 53 241 658 |
| Деталь: | SPACER |
| Парткод: | A374 2181 |
| Деталь: | Entrance Scanning Roller Shaft |
| Парткод: | B477 2575 |
| Деталь: | Arm:Roller:Scanning:Entrance |
| Парткод: | B477 2574 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A422 1063 |
| Деталь: | Entrance Scanning Base |
| Парткод: | B477 2561 |
| Деталь: | Guide Bracket |
| Парткод: | B477 2145 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Harness:Registration Sensor |
| Парткод: | B652 5431 |
| Деталь: | Registration Sensor Bracket |
| Парткод: | B477 2665 |
| Деталь: | Guide Plate:Entrance:Upper:Assy |
| Парткод: | B652 3251 |
| Деталь: | Discharge Brush |
| Парткод: | A859 3225 |
| Деталь: | Drive Relay Roller |
| Парткод: | B477 2121 |
| Деталь: | Roller:Scanning:Entrance:Drive |
| Парткод: | B652 2411 |
| Деталь: | Roller:Pull Out:Drive |
| Парткод: | B652 2112 |
| Деталь: | Roller:Scanning:Exit:Drive |
| Парткод: | B652 2421 |
| Деталь: | Timing Belt:B80S3M417 |
| Парткод: | B6521783 |
| Деталь: | Timing Belt:B60S2M172 |
| Парткод: | B652 3135 |
| Деталь: | Paper Feed Cover Bracket |
| Парткод: | B4771775 |
| Деталь: | Bushing - 16x18x5 |
| Парткод: | AA08 2141 |
| Деталь: | Screw: Safety |
| Парткод: | AA14 3791 |
| Деталь: | Timing Belt:B40S2M230 |
| Парткод: | B652 4153 |
| Деталь: | Timing Pulley - T28 S2M |
| Парткод: | A806 2111 |
| Деталь: | Duplex Turn Roller |
| Парткод: | AF02 1075 |
| Деталь: | Driven Transport Roller |
| Парткод: | AF02 1077 |
| Деталь: | Drive Inverter Roller |
| Парткод: | AF02 1076 |
| Деталь: | Left Drive Roller |
| Парткод: | AF02 1078 |
| Деталь: | Jogger Guide Rod |
| Парткод: | B065 4694 |
| Деталь: | Right Drive Roller |
| Парткод: | AF02 1079 |
| Деталь: | Timing Pulley - 24Z |
| Парткод: | AB03 0583 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2118 |
| Деталь: | Timing Belt:40S2M278G |
| Парткод: | AA04 3310 |
| Деталь: | Timing Belt:40S2M302G |
| Парткод: | AA04 3311 |
| Деталь: | Gear:45Z |
| Парткод: | AB01 1 497 |
| Деталь: | PULLEY |
| Парткод: | AB01 7614 |
| Деталь: | Gear:22Z |
| Парткод: | AB01 1498 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 1496 |
| Деталь: | Pulley - 29Z |
| Парткод: | AB03 0731 |
| Деталь: | Seal:C/T Box:Cover:Side |
| Парткод: | B132 5812 |
| Деталь: | Seal:C/T Box:Cover:Middle |
| Парткод: | B132 5809 |
| Деталь: | Gasket:Cover:C/T Box |
| Парткод: | B132 5831 |
| Деталь: | Cover:C/T Box:Small |
| Парткод: | B132 5958 |
| Деталь: | Harness:HDD:RAID1 |
| Парткод: | B132 5731 |
| Деталь: | Harness:HDD:RAID2 |
| Парткод: | B132 5732 |
| Деталь: | Harness:HDD:RAID3 |
| Парткод: | B132 5733 |
| Деталь: | Harness:HDD:RAID4 |
| Парткод: | B132 5734 |
| Деталь: | Harness:HDD:Power Source |
| Парткод: | B132 5735 |
| Деталь: | HDD Assy |
| Парткод: | B132 5820 |
| Деталь: | PCB: Interface |
| Парткод: | B132 5762 |
| Деталь: | Right Guide 1 |
| Парткод: | G1085108 |
| Деталь: | Left Guide 1 |
| Парткод: | G1085107 |
| Деталь: | NVRAM |
| Парткод: | B132 9590 |
| Деталь: | Sheet:Cover:C/T Box |
| Парткод: | B132 5832 |
| Деталь: | PCB:Control Board |
| Парткод: | B132 5768 |
| Деталь: | SD-Card:Copy |
| Парткод: | B132 5730 |
| Деталь: | Rail:Upper:Long:Right |
| Парткод: | B132 5923 |
| Деталь: | Rail:Upper:Long:Left |
| Парткод: | B132 5924 |
| Деталь: | Drum Stay:Control Board:Welding |
| Парткод: | B132 5928 |
| Деталь: | Ground Plate:Panel |
| Парткод: | B070 6899 |
| Деталь: | Large Drum Stay Ground Plate |
| Парткод: | B070 6877 |
| Деталь: | Ground Plate:Drum Stay:Small |
| Парткод: | B070 6879 |
| Деталь: | Grip:Bracket:Control Board |
| Парткод: | B132 5816 |
| Деталь: | Decal:Caption: Interface |
| Парткод: | B132 5818 |
| Деталь: | Cover:SD-Card:Control Board |
| Парткод: | B132 5969 |
| Деталь: | Cover:Connector:Control Board |
| Парткод: | B132 5925 |
| Деталь: | Interface Panel Assy |
| Парткод: | B070 6894 |
| Деталь: | Knob Screw:Panel |
| Парткод: | B070 6898 |
| Деталь: | Guard:GAP:C/T Box |
| Парткод: | B132 1528 |
| Деталь: | Decal:Caution:HDD:Fan |
| Парткод: | B132 5819 |
| Деталь: | Slide Rail:Right:Assy |
| Парткод: | B132 6693 |
| Деталь: | Decal - Paper Tray 2 |
| Парткод: | B065 6636 |
| Деталь: | Decal- Paper Tray 3 |
| Парткод: | B065 6637 |
| Деталь: | Slide Rail:Left:Sub-assy |
| Парткод: | B132 6692 |
| Деталь: | Paper Tray Cover - Long |
| Парткод: | B065 6632 |
| Деталь: | Paper Tray Cover - Short |
| Парткод: | B065 6633 |
| Деталь: | Left Support Plate |
| Парткод: | B065 6589 |
| Деталь: | Right Support Plate |
| Парткод: | B065 6588 |
| Деталь: | Paper Tray Holder Base |
| Парткод: | B065 6591 |
| Деталь: | Stay:Holder:Paper Tray:Assy |
| Парткод: | B132 6653 |
| Деталь: | Total Counter:7FIG:24V:MI2 |
| Парткод: | AX31 0047 |
| Деталь: | Bracket:Total Counter |
| Парткод: | B132 5976 |
| Деталь: | Decal:Total Counter |
| Парткод: | B132 5996 |
| Деталь: | Base:Slide Rail:No.2:Peen |
| Парткод: | B065 6781 |
| Деталь: | Tray Lock Spring - 19mm |
| Парткод: | AA06 0534 |
| Деталь: | T ray Lock Arm |
| Парткод: | B065 6136 |
| Деталь: | Slide Rail Base |
| Парткод: | B065 6783 |
| Деталь: | Stay:Machine or Copier:Left:Peen |
| Парткод: | B132 1115 |
| Деталь: | Cover:Stay:Left |
| Парткод: | B1321222 |
| Деталь: | Slide Rail:Pull Out:Left |
| Парткод: | AA07 0066 |
| Деталь: | Bracket:Sensor:Entrance |
| Парткод: | B132 7101 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0107 |
| Деталь: | Harness:Exit:Sensor |
| Парткод: | B132 5253 |
| Деталь: | Stud:Guide Pin |
| Парткод: | AA14 3421 |
| Деталь: | Guide Plate:Left Lower:Assy |
| Парткод: | B132 7114 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3907 |
| Деталь: | Stopper:Pressure |
| Парткод: | B132 7038 |
| Деталь: | Slide Rail:Toner Supply:Assy |
| Парткод: | AA07 0064 |
| Деталь: | Stay:Slide Rail:Toner Supply |
| Парткод: | B132 3486 |
| Деталь: | Guide:Registration:Open And Close |
| Парткод: | B132 2718 |
| Деталь: | Slide Rail:Pull Out:Right |
| Парткод: | AA07 0067 |
| Деталь: | Stay:Machine Or Copier:Right Lower |
| Парткод: | B132 1004 |
| Деталь: | Lever:Large Capacity Tray |
| Парткод: | B132 2717 |
| Деталь: | Shaft:Guide Plate |
| Парткод: | B132 2666 |
| Деталь: | Guide Plate:LCT |
| Парткод: | B132 2637 |
| Деталь: | Left Gasket - Front Rear |
| Парткод: | B0101289 |
| Деталь: | Magnet Catch:Original Table:25.5N |
| Парткод: | AG07 0513 |
| Деталь: | Bushing:6x8x5 |
| Парткод: | AA08 0265 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0960 |
| Деталь: | Guide Plate:LCT:Open And Close |
| Парткод: | B132 2662 |
| Деталь: | Bracket:Sensor:Large Capacity Tray |
| Парткод: | B132 2654 |
| Деталь: | Harness:Paper Feed Unit |
| Парткод: | B132 5250 |
| Деталь: | Bracket:Cover:LCT |
| Парткод: | B1321008 |
| Деталь: | Bracket:Fix:Manual Feed |
| Парткод: | B132 2815 |
| Деталь: | Stepper Motor:Paper Feed Unit:Assy |
| Парткод: | B132 6655 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0958 |
| Деталь: | Bracket:Drive:Paper Feed Sub-unit |
| Парткод: | B132 2760 |
| Деталь: | Timing Pulley:35T |
| Парткод: | AB03 0301 |
| Деталь: | Timing Belt:40S2M150 |
| Парткод: | AA04 3313 |
| Деталь: | Spacer - 1x8x12 |
| Парткод: | AA13 2025 |
| Деталь: | Ball Bearing - 8x12x5 |
| Парткод: | A247 2800 |
| Деталь: | Harness:Fusing:100V:C1a (B132) |
| Парткод: | B132 5371 |
| Деталь: | Harness:Power Supply Unit:Fusing:200V(B181) |
| Парткод: | B132 5373 |
| Деталь: | Harness:Power Supply Unit:Fusing:100V(B200) |
| Парткод: | B132 5372 |
| Деталь: | Harness:Power Supply Unit:200V (B200) |
| Парткод: | B132 5374 |
| Деталь: | Gear:103Z |
| Парткод: | AB01 0133 |
| Деталь: | Shaft:Drive: Vacuum |
| Парткод: | B1321367 |
| Деталь: | Gear:22Z |
| Парткод: | AB01 1250 |
| Деталь: | DC Motor:DIA86:38W |
| Парткод: | AX06 0279 |
| Деталь: | Bracket:Drive:Fusing:Assy |
| Парткод: | B1321350 |
| Деталь: | Timing Pulley:47T |
| Парткод: | AB03 0770 |
| Деталь: | Timing Pulley:47T |
| Парткод: | AB03 0768 |
| Деталь: | Gear:Pulley:96Z/30T |
| Парткод: | AB01 7685 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 0951 |
| Деталь: | Bracket:Tightener:Assy |
| Парткод: | B132 1356 |
| Деталь: | Shaft:Drive:Fusing:Assy |
| Парткод: | B1321360 |
| Деталь: | Pulley:Idler |
| Парткод: | B132 1370 |
| Деталь: | Timing Belt:40S3M471 |
| Парткод: | AA04 3965 |
| Деталь: | Timing Belt:60S3M741 |
| Парткод: | AA04 3964 |
| Деталь: | Timing Pulley:44t |
| Парткод: | AB03 0771 |
| Деталь: | Timing Pulley:44t |
| Парткод: | AB03 0772 |
| Деталь: | Shaft:Drive:Reverse:Assy |
| Парткод: | B1321363 |
| Деталь: | Bracket:Sub:Drive:Fusing |
| Парткод: | B132 1355 |
| Деталь: | Gear:40Z |
| Парткод: | AB01 1304 |
| Деталь: | Gear:30Z |
| Парткод: | AB01 1302 |
| Деталь: | Bracket:Gear: Swivel |
| Парткод: | B132 2679 |
| Деталь: | Spacer:MM12 |
| Парткод: | B132 2699 |
| Деталь: | Shaft:Drive:Paper Feed |
| Парткод: | B132 2762 |
| Деталь: | Gear:33Z |
| Парткод: | AB01 1303 |
| Деталь: | Stepped Screw - M3x26.5 |
| Парткод: | A555 1671 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B132 6550 |
| Деталь: | Bracket:Used Toner Sensor:Install |
| Парткод: | B132 6547 |
| Деталь: | Oil End Sensor |
| Парткод: | AW02 0164 |
| Деталь: | Harness:Bank:Middle |
| Парткод: | B132 5394 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B132 6566 |
| Деталь: | Gear -30Z |
| Парткод: | AB01 3467 |
| Деталь: | Bracket:Used Toner Sensor |
| Парткод: | B132 6525 |
| Деталь: | Bracket:Dc Motor:No.2 |
| Парткод: | B132 6544 |
| Деталь: | Gear: 17/51Z |
| Парткод: | AB01 7000 |
| Деталь: | Shaft:Idler:DC Motor |
| Парткод: | B132 6593 |
| Деталь: | DC Motor:On-Off:Assy (B132)(B200) |
| Парткод: | B180 3991 |
| Деталь: | DC Motor:Rise:Paper Tray |
| Парткод: | AX04 0144 |
| Деталь: | Paper Tray Positioning Bracket |
| Парткод: | B065 6174 |
| Деталь: | Paper Tray Stopper |
| Парткод: | B065 6172 |
| Деталь: | Bracket:Paper Size Sensor:No.1 |
| Парткод: | B132 6737 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0010 |
| Деталь: | Harness:Bank:Tray:Paper Size Sensor |
| Парткод: | B132 5397 |
| Деталь: | Bracket:Power Supply Unit:Right |
| Парткод: | B132 5977 |
| Деталь: | Bracket:Earth:Power Supply Unit:Rear:Peen |
| Парткод: | B132 5827 |
| Деталь: | Bracket:Power Supply Unit:Right:EXP |
| Парткод: | B132 5997 |
| Деталь: | Duplex Gate Pawl |
| Парткод: | B065 4733 |
| Деталь: | Gate Pawl Cushion |
| Парткод: | B065 4738 |
| Деталь: | Lower Duplex Guide Plate |
| Парткод: | A294 4626 |
| Деталь: | SPACER |
| Парткод: | B065 4865 |
| Деталь: | Stay:Timing Belt |
| Парткод: | B132 4689 |
| Деталь: | Timing Belt - 40S2M810G |
| Парткод: | AA04 3294 |
| Деталь: | Slider:Jogger Fence:Front |
| Парткод: | B132 4692 |
| Деталь: | Slider:Jogger Fence:Rear |
| Парткод: | B132 4693 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0148 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0149 |
| Деталь: | Bracket:Sensor:Reverse:Exit |
| Парткод: | B132 4715 |
| Деталь: | Gear - 30Z/45Z |
| Парткод: | AB01 7615 |
| Деталь: | Guide Plate:Transport:Upper:Assy |
| Парткод: | B132 4710 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0984 |
| Деталь: | DC Solenoid:Gate Pawl:Assy |
| Парткод: | B132 4740 |
| Деталь: | Duplex Guide |
| Парткод: | A096 4595 |
| Деталь: | Bracket:Support:Positioning Pin |
| Парткод: | B132 4619 |
| Деталь: | Bracket:Drawer:32pin:Duplex |
| Парткод: | B132 4790 |
| Деталь: | Harness:Duplex Unit:32p |
| Парткод: | B132 5261 |
| Деталь: | Bracket:Drawer:12pin:Duplex |
| Парткод: | B132 4791 |
| Деталь: | Harness:Duplex Unit:12pin |
| Парткод: | B132 5262 |
| Деталь: | Jogger Pulley |
| Парткод: | AB03 0732 |
| Деталь: | SPRING |
| Парткод: | AA06 2318 |
| Деталь: | Jogger Bracket |
| Парткод: | B065 4820 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket:Home Position Sensor:Jogger |
| Парткод: | B132 4699 |
| Деталь: | Tension Spring:Lock:Lever |
| Парткод: | B652 3145 |
| Деталь: | Hook:Lock:Image Reading Unit:Front |
| Парткод: | B652 3144 |
| Деталь: | Shaft:Lever:Misfeed Removal:Assy |
| Парткод: | B652 3141 |
| Деталь: | Transport Belt |
| Парткод: | B652 3121 |
| Деталь: | Roller:Transport Belt:Drive |
| Парткод: | B652 3112 |
| Деталь: | Stopper:Roller:Drive |
| Парткод: | B652 3119 |
| Деталь: | Discharge Brush:Short |
| Парткод: | B652 3158 |
| Деталь: | Discharge Brush:Long |
| Парткод: | B652 3157 |
| Деталь: | Discharge Brush:Middle |
| Парткод: | B652 3159 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B477 2621 |
| Деталь: | Guide:Transport Belt:Front |
| Парткод: | B652 3116 |
| Деталь: | Housing:Transport Belt Unit |
| Парткод: | B652 3110 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B652 3125 |
| Деталь: | Guide:Transport Belt:Rear |
| Парткод: | B652 3117 |
| Деталь: | Spacer:Transport Belt |
| Парткод: | B652 3156 |
| Деталь: | Roller:Pressure |
| Парткод: | B652 3113 |
| Деталь: | Bracket: Roller: Driven |
| Парткод: | B652 3123 |
| Деталь: | Driven Roller:Scanning |
| Парткод: | B652 3124 |
| Деталь: | Pin:Guide Plate:Paper Feed |
| Парткод: | AA14 3788 |
| Деталь: | DC Solenoid:Reverse:Lower:Assy |
| Парткод: | B652 4766 |
| Деталь: | Lever:Reverse:Lower:DC Solenoid |
| Парткод: | B652 4532 |
| Деталь: | Bracket:Reverse:Lower:DC Solenoid |
| Парткод: | B652 4533 |
| Деталь: | Damper - Junction Gate Solenoid |
| Парткод: | A697 2102 |
| Деталь: | Lens Unit |
| Парткод: | B132 1731 |
| Деталь: | INTERFACE CABLE |
| Парткод: | B132 5369 |
| Деталь: | COVER |
| Парткод: | B132 1674 |
| Деталь: | Bracket:Open And Close:Left |
| Парткод: | B132 1871 |
| Деталь: | Rubber Bushing |
| Парткод: | A2571884 |
| Деталь: | Bracket: Positioning: Left |
| Парткод: | B132 1877 |
| Деталь: | Cushion - Motor |
| Парткод: | AA16 1104 |
| Деталь: | Spring Plate:Earth:Scanner Unit |
| Парткод: | B1321897 |
| Деталь: | Bracket:Positioning:Right |
| Парткод: | B132 1874 |
| Деталь: | Lever:Scanner Unit:Open And Close |
| Парткод: | B132 1886 |
| Деталь: | Fan Motor:Mm60 |
| Парткод: | AX64 0151 |
| Деталь: | Bracket:Open And Close:Right |
| Парткод: | B132 1872 |
| Деталь: | Ground Wire:Scanner |
| Парткод: | B132 1896 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Sheet - Photointerrupter |
| Парткод: | A267 1820 |
| Деталь: | Ground Plate:Scanner:Rear |
| Парткод: | B132 1112 |
| Деталь: | Plate:Rod |
| Парткод: | B132 1889 |
| Деталь: | Rod:Open And Close:Scanner Unit |
| Парткод: | B1321888 |
| Деталь: | Seal:Inner Cover |
| Парткод: | B1321678 |
| Деталь: | Cover:Siob |
| Парткод: | B132 1677 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Guide Roller - B |
| Парткод: | A300 2134 |
| Деталь: | Rail:Left:Assy |
| Парткод: | B132 4835 |
| Деталь: | Rail:Right:Assy |
| Парткод: | B132 4591 |
| Деталь: | Roller - Positioning Guide |
| Парткод: | 67 542 866 |
| Деталь: | Hexagonal Bolt:M12x35 |
| Парткод: | AA14 3798 |
| Деталь: | Heat Sink:Heater:Lower:NA:Assy |
| Парткод: | B140 6225 |
| Деталь: | Heat Sink:Heater:Lower:EU:Assy |
| Парткод: | B140 6226 |
| Деталь: | Cover:Temperature/Humidity Sensor |
| Парткод: | B132 6579 |
| Деталь: | Guide:Tank:Discharge Used Toner |
| Парткод: | B132 6577 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW14 0012 |
| Деталь: | Caster: 1470n |
| Парткод: | AH01 2031 |
| Деталь: | Flanged Hexagonal Head Bolt:Caster |
| Парткод: | AA14 3803 |
| Деталь: | Harness:Duplex:Fan:Middle |
| Парткод: | B132 5266 |
| Деталь: | Fan Motor:MM80 |
| Парткод: | AX64 0163 |
| Деталь: | Bracket:Fan:Duplex |
| Парткод: | B132 1118 |
| Деталь: | Cushion - Motor |
| Парткод: | AA16 1104 |
| Деталь: | PAPER GUIDE SHEET |
| Парткод: | A096 6693 |
| Деталь: | BRACKET |
| Парткод: | B065 1092 |
| Деталь: | Bracket: Holder: Assy |
| Парткод: | B132 4830 |
| Деталь: | Harness:Transfer Unit:MCY |
| Парткод: | B132 5352 |
| Деталь: | Terminal:Collar |
| Парткод: | B132 6140 |
| Деталь: | Terminal:Yellow |
| Парткод: | B132 6149 |
| Деталь: | Compression Spring:Transfer:Collar:Rear |
| Парткод: | B132 6147 |
| Деталь: | Plate:Upper:Positioning Sensor:Assy |
| Парткод: | B132 6178 |
| Деталь: | Positioning Sensor:Assy |
| Парткод: | B132 6141 |
| Деталь: | Image Transfer Belt |
| Парткод: | B132 6050 |
| Деталь: | Harness:Positioning Sensor |
| Парткод: | B132 5378 |
| Деталь: | Bushing:Front |
| Парткод: | B132 6116 |
| Деталь: | BUSHING |
| Парткод: | B132 6115 |
| Деталь: | Compression Spring:Transfer:Collar |
| Парткод: | B132 6144 |
| Деталь: | Roller:Driven |
| Парткод: | B132 6061 |
| Деталь: | Roller:Intermediate Transfer |
| Парткод: | B132 6080 |
| Деталь: | Bracket:Collar |
| Парткод: | B132 6077 |
| Деталь: | Harness:Transfer Unit:K |
| Парткод: | B132 5351 |
| Деталь: | Terminal:Black |
| Парткод: | B132 6137 |
| Деталь: | Shaft:Contact Point:Collar |
| Парткод: | B132 6098 |
| Деталь: | Compression Spring:Transfer:Black |
| Парткод: | B132 6133 |
| Деталь: | Bracket:On-off:Black |
| Парткод: | B132 6076 |
Коды ошибок
SC101
SC120
SC121
SC141
SC142
SC144
SC161
SC180
SC195
SC202
SC203
SC204
SC205
SC210
SC211
SC212
SC213
SC220
SC221
SC222
SC223
SC224
SC225
SC226
SC227
SC230
SC231
SC232
SC233
SC234
SC235
SC236
SC237
SC240
SC241
SC242
SC243
SC268
SC269
SC300
SC301
SC302
SC303
SC312
SC313
SC314
SC315
SC316
SC317
SC318
SC319
SC320
SC321
SC322
SC323
SC324
SC325
SC326
SC327
SC336
SC337
SC338
SC339
SC340
SC341
SC342
SC343
SC348
SC360
SC361
SC362
SC363
SC364
SC365
SC366
SC367
SC372
SC373
SC374
SC375
SC396
SC397
SC398
SC399
SC400
SC410
SC411
SC412
SC413
SC414
SC415
SC416
SC417
SC418
SC420
SC421
SC422
SC423
SC424
SC425
SC426
SC427
SC432
SC433
SC434
SC435
SC436
SC437
SC438
SC439
SC440
SC441
SC442
SC443
SC445
SC446
SC450
SC455
SC460
SC484
SC485
SC487
SC488
SC496
SC497
SC498
SC503
SC504
SC505
SC506
SC510
SC515
SC516
SC530
SC531
SC532
SC533
SC534
SC541
SC542
SC543
SC544
SC545
SC546
SC547
SC548
SC549
SC550
SC551
SC552
SC553
SC554
SC555
SC556
SC561
SC562
SC563
SC564
SC565
SC620
SC621
SC622
SC624
SC630
SC632
SC633
SC634
SC635
SC670
SC672
SC680
SC687
SC701
SC705
SC720
SC721
SC723
SC724
SC725
SC726
SC727
SC728
SC730
SC740
SC741
SC742
SC743
SC744
SC750
SC751
SC752
SC753
SC760
SC761
SC762
SC763
SC764
SC765
SC766
SC767
SC770
SC775
SC790
SC817
SC818
SC819
SC821
SC822
SC824
SC826
SC828
SC833
SC834
SC850
SC851
SC853
SC854
SC855
SC856
SC857
SC860
SC861
SC863
SC864
SC865
SC866
SC867
SC868
SC870
SC873
SC874
SC875
SC880
SC900
SC920
SC921
SC925
SC990
SC991
SC992
SC997
SC998
Описание
| Error code: | SC101 |
| Description: | Exposure lamp error The white level peak did not reach the prescribed threshold when the white plate was scanned. |
| Causes: | The scanner has scanned the white plate, but cannot detect the certain white level. • Defective exposure lamp • Defective exposure lamp stabilizer • Defective power source harness • Defective signal harness • High-voltage cable leak • Defective darkness starting characteristic |
| Remedy: | • Dirty optics • Exposure lamp defective • Exposure lamp does not turn ON • Lamp stabilizer defective • High voltage line leak • Power/signal harness defective |
| Error code: | SC120 |
| Description: | Scanner home position error 1 The scanner home position sensor did not detect the home position (did not go OFF) after the scanner moved forward 20 mm.. |
| Causes: | The scanner home position sensor does not detect the scanner leaving the home position. • Defective scanner home position sensor • Defective scanner home position sensor harness • Defective scanner motor driver • Defective scanner motor |
| Remedy: | • Scanner motor driver board defective • Scanner motor defective • Scanner HP sensor defective • Harness between scanner motor and scanner I/O board disconnected or broken. |
| Error code: | SC121 |
| Description: | Scanner home position error 2 The scanner home position sensor did not go ON after the scanner moved forward 1 mm and the feeler entered the HP sensor. |
| Causes: | The scanner home position sensor does not detect the scanner coming back to the home position. • Defective scanner home position sensor • Defective scanner home position sensor harness • Defective scanner motor driver • Defective scanner motor |
| Remedy: | • Scanner motor defective • Scanner HP sensor disconnected, defective |
| Error code: | SC141 |
| Description: | Black level detection error During AGC the value for black level was not within ±2 of the prescribed value. The copier can reproduce monochrome, but not color. |
| Causes: | The automatic adjustment has failed to correct the black level to the permissible range. • Defective SBU board • Defective harness |
| Remedy: | • SBU defective • Harness defective |
| Error code: | SC142 |
| Description: | White level detection error During AGC the value for white level was not within ±7 of the prescribed value. |
| Causes: | The automatic adjustment has failed to correct the white level to the permissible range. • Defective scanner drive • Defective optical section • Defective SBU board • Defective harness |
| Remedy: | • Exposure lamp defective • Harness disconnected, damaged • Dirty exposure glass, optics • Scanner motor, drive assembly defective • SBU board defective |
| Error code: | SC144 |
| Description: | SBU (Sensor Board Unit) communication error When the machine is switched ON, or when the machine returns to full operation from the energy save mode, the machine can not access the SBU register, or the SBU register values are abnormal. |
| Causes: | Cannot correctly establish communication with the SBU. • Defective harness • Defective destination device (e.g., BICU, etc) • Defective SBU |
| Remedy: | • Dirty exposure glass or optics • SBU board defective • SBU harness disconnected, defective |
| Error code: | SC161 |
| Description: | IDU (Image Discrimination Unit) error After the command is written into the DFID self-diagnosis startup register, the correct value is not stored in the register for the prescribed length of time after power ON. -or- After the negate interruption of FGATE occurs, IDU is not recognized within the prescribed time during scanning. |
| Causes: | • Check harness connections between SBU and IPU/VBCU • IPU defective • VBCU defective |
| Remedy: | • IPU board defective (defective connection between ASIC and DFID, defective LSYNC-signal) |
| Error code: | SC180 |
| Description: | Scanner Unit Exhaust Fan Lock The scanner unit exhaust fan did not switch on within 10 sec. after the CPU issued the ON signal. |
| Causes: | • Foreign object interfering with operation of fan • Fan motor harness disconnected or defective • Fan defective • SIOB board defective • SBU board defective |
| Error code: | SC195 |
| Description: | Machine serial number error The number registered for the machine serial number does not match. |
| Causes: | Comparison of the product identification code in the machine serial number (11 digits). The product identification code in the machine serial number (11 digits) does not match. |
| Remedy: | • Confirm the correct serial number of the machine in the specifications Important! WHEN SC195 OCCURS, THE SERIAL NUMBER MUST BE INPUT. PLEASE CONTACT YOUR TECHNICAL SUPERVISOR. |
| Error code: | SC202 |
| Description: | Polygon motor error 1: ON timeout The polygon mirror motor does not reach the targeted operating speed: • Within 10 seconds after turning ON. • Within 10 sec. after changing speed |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective • Polygon motor defective. |
| Error code: | SC203 |
| Description: | Polygon motor error 2: OFF timeout The polygon mirror motor does leave the READY status within 10 seconds after the polygon motor switches OFF. |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective • Polygon motor defective. |
| Error code: | SC204 |
| Description: | Polygon motor error 3: Polygon motor lock signal error The polygon motor lock signal goes HIGH (inactive) while the laser diode is firing. |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective |
| Error code: | SC205 |
| Description: | Polygon motor error 4: Polygon motor lock signal unstable When the polygon motor switches ON, or after the speed of the motor changes, the polygon motor lock signal goes HIGH (inactive). |
| Causes: | • Switch the machine off/on (problem was probably due to electronic noise) • Replace the harness if cycling the machine off/on does not solve the problem • Polygon motor defective • Polygon mirror motor control board defective • IPU defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective |
| Error code: | SC210 |
| Description: | Laser beam detection error 1: K (Black) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • CK Laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC211 |
| Description: | Laser beam detection error 1: Y (Yellow) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • CK laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC212 |
| Description: | Laser beam detection error 1: M (Magenta) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC213 |
| Description: | Laser beam detection error 1: C (Cyan) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC220 |
| Description: | Laser Synchronization Detector Error 1: K Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 black, or leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU is defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC221 |
| Description: | Laser Synchronization Detector Error 2: K Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for black, leading edge for any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC222 |
| Description: | Laser Synchronization Detector Error 1: Y Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 yellow, leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) (ASIC) on the BICU defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC223 |
| Description: | Laser Synchronization Detector Error 2: Y Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for yellow, leading edgefor any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC224 |
| Description: | Laser Synchronization Detector Error 1: M Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 magenta, leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC225 |
| Description: | Laser Synchronization Detector Error 2: M Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for magenta, leading edge for any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC226 |
| Description: | Laser Synchronization Detector Error 1: C Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 cyan, leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Cycle the machine off/on • YM Laser unit defective |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC227 |
| Description: | Laser Synchronization Detector Error 2: C Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for cyan, leading edgefor any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC230 |
| Description: | FGATE error 1: Feedback remains HIGH for K write After the start of timing to create the black image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC231 |
| Description: | FGATE error 1: Feedback remains LOW for K write After the start of timing to create the black image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC232 |
| Description: | FGATE error 1: Feedback remains HIGH for Y write After the start of timing to create the yellow image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC233 |
| Description: | FGATE error 1: Feedback remains LOW for Y write. After the start of timing to create the yellow image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC234 |
| Description: | FGATE error 1: Feedback remains HIGH for M write. After the start of timing to create the magenta image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC235 |
| Description: | FGATE error 1: Feedback remains LOW for M write. After the start of timing to create the magenta image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC236 |
| Description: | FGATE error 1: Feedback remains HIGH for C write. After the start of timing to create the cyan image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC237 |
| Description: | FGATE error 1: Feedback remains LOW for C write. After the start of timing to create the cyan image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC240 |
| Description: | LD error 1: K An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD. |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC241 |
| Description: | LD error 1: Y An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Cycle the machine off/on • CK laser unit defective |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC242 |
| Description: | LD error 1: M An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC243 |
| Description: | LD error 1: C An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC268 |
| Description: | Optical unit sensor error. At power ON, one of the two temperature sensors in the optics unit detected a temperature lower than 0°C for more than 1 sec. -or- It detected a temperature higher than 100°C for more than 1 sec. |
| Causes: | After the main power switch ON, writing thermistor temperature is detected at 100ms intervals an ... • Less than -30 degrees Celsius is detected for more than 4 seconds (Thermistor defective). • More than 105 degrees Celsius is detected for more than 1 second (Thermistor short). |
| Remedy: | • Thermistor disconnected (causes extremely low temperature reading) • Thermistor damaged and short circuited (causes extremely high temperature reading) • BICU defective |
| Error code: | SC269 |
| Description: | Exposure thermistor 2 error. At power on, exposure thermistor 2 detected a temperature lower than 0°C for more than 1 sec. -or- It detected a temperature higher than 100°C for more than 1 sec. |
| Causes: | • Thermistor disconnected (causes extremely low temperature reading) • Thermistor damaged and short circuited (causes extremely high temperature reading) • BCU defective |
| Remedy: | • Thermistor disconnected (causes extremely low temperature reading) • Thermistor damaged and short circuited (causes extremely high temperature reading) • BICU defective |
| Error code: | SC300 |
| Description: | AC charge output error 1: K An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC301 |
| Description: | AC charge output error 2: M An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | • Disconnect the high voltage cable from Terminal C of the power pack. • Attach a voltmeter to the terminal. • If there is no output from the terminal, replace the power pack. -or- • If there is output from the terminal, test the resistance between the high voltage cable and the ground. • If resistance is nearly "0", check the high-voltage harness for defects and replace it if necessary. • Test the conductivity between the PCU and the ground. If there is no conductivity between the PCU and ground, replace the PCU. • If there is no charge PWM signal, replace the harness and/or BCU. |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC302 |
| Description: | AC charge output error 3: C An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | This SC is issued if the BICU detects a short in the power pack 10 times consecutively. Open circuit (+) / Short circuit (-) |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC303 |
| Description: | AC charge output error 4: Y An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | • Disconnect the high voltage cable from Terminal C of the power pack. • Attach a voltmeter to the terminal. • If there is no output from the terminal, replace the power pack. -or- • If there is output from the terminal, test the resistance between the high voltage cable and the ground. • If resistance is nearly "0", check the high-voltage harness for defects and replace it if necessary. • Test the conductivity between the PCU and the ground. If there is no conductivity between the PCU and ground, replace the PCU. • If there is no charge PWM signal, replace the harness and/or BCU. |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC312 |
| Description: | Charge, development error 1: K 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Pre-charge unit set incorrectly. • Pre-charge unit contact is broken or defective. |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC313 |
| Description: | Charge, development error 2: M 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Make sure that the settings of SP2202 are at the defaults. • Check harness connections between charge roller and transfer power pack. • Defective charge roller • Defective power pack |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC314 |
| Description: | Charge, development error 3: C 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Make sure that the settings of SP2202 are at the defaults. • Check harness connections between charge roller and transfer power pack. • Defective charge roller • Defective power pack |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC315 |
| Description: | Charge, development error 4: Y 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Make sure that the settings of SP2202 are at the defaults. • Check harness connections between charge roller and transfer power pack. • Defective charge roller • Defective power pack |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC316 |
| Description: | AC bias charge adjustment error 1: K An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC317 |
| Description: | AC bias charge adjustment error 2: M An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC318 |
| Description: | AC bias charge adjustment error 3: C An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC319 |
| Description: | AC bias charge adjustment error 4: Y An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC320 |
| Description: | Development power pack error 1: K An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC321 |
| Description: | Development power pack error 2: M An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC322 |
| Description: | Development power pack error 3: C An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC323 |
| Description: | Development power pack error 4: Y An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC324 |
| Description: | Development motor error 1: K The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC325 |
| Description: | Development motor error 2: M The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC326 |
| Description: | Development motor error 3: C The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC327 |
| Description: | Development motor error 4: Y The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC336 |
| Description: | Developer set error 1: K The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC337 |
| Description: | Developer set error 2: M The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC338 |
| Description: | Developer set error 3: C The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC339 |
| Description: | Developer set error 4: Y The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC340 |
| Description: | Toner cartridge set error 1: K The machine cannot read the ID chip of the black, magenta, cyan, or yellow toner cartridge. |
| Causes: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly |
| Remedy: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly 1. Open the front door. 2. Press down the release lever on the top edge of the toner bin to of the affect toner cartridge to release it, then pull the bin out to open it. 3. Remove the toner cartridge and set it again. |
| Error code: | SC341 |
| Description: | Toner cartridge set error 2: M The machine cannot read the ID chip of the black, magenta, cyan, or yellow toner cartridge. |
| Causes: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly |
| Remedy: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly 1. Open the front door. 2. Press down the release lever on the top edge of the toner bin to of the affect toner cartridge to release it, then pull the bin out to open it. 3. Remove the toner cartridge and set it again. |
| Error code: | SC342 |
| Description: | Toner cartridge set error 3: C The machine cannot read the ID chip of the black, magenta, cyan, or yellow toner cartridge. |
| Causes: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly |
| Remedy: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly 1. Open the front door. 2. Press down the release lever on the top edge of the toner bin to of the affect toner cartridge to release it, then pull the bin out to open it. 3. Remove the toner cartridge and set it again. |
| Error code: | SC343 |
| Description: | Toner cartridge set error 4: Y The machine cannot read the ID chip of the black, magenta, cyan, or yellow toner cartridge. |
| Causes: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly |
| Remedy: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly 1. Open the front door. 2. Press down the release lever on the top edge of the toner bin to of the affect toner cartridge to release it, then pull the bin out to open it. 3. Remove the toner cartridge and set it again. |
| Error code: | SC348 |
| Description: | Toner hopper motor error. 2 sec. after the motor START signal is output, a LOCK signal cannot be detected. |
| Causes: | • Motor harness disconnected, loose, or defective • Toner pump overload • Sub hopper overload • Toner hopper motor defective |
| Remedy: | • Motor harness disconnected, loose, or defective • Powder pump overload • Sub hopper overload • Toner hopper motor defective |
| Error code: | SC360 |
| Description: | TD sensor (Vt high) error 1: K The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC361 |
| Description: | TD sensor (Vt high) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC362 |
| Description: | TD sensor (Vt high) error 3: C The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC363 |
| Description: | TD sensor (Vt high) error 4: Y The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC364 |
| Description: | TD sensor (Vt low) error 1: K The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective, replace the PCU Note: The TD sensor cannot be replaced independently. The PCU must be replaced if the TD sensor is defective. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC365 |
| Description: | TD sensor (Vt low) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | These SC codes are issued if the TD sensor output is less than 0.5V after 10 consecutive readings. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC366 |
| Description: | TD sensor (Vt low) error 3: C The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | These SC codes are issued if the TD sensor output is less than 0.5V after 10 consecutive readings. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC367 |
| Description: | TD sensor (Vt low) error 4: Y The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | These SC codes are issued if the TD sensor output is less than 0.5V after 10 consecutive readings. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC372 |
| Description: | TD sensor adjustment error 1: K During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | The TD sensor of the affected development unit could not be initialized within 2.9±0.2V. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC373 |
| Description: | TD sensor adjustment error 2: M During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | The TD sensor of the affected development unit could not be initialized within 2.9±0.2V. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC374 |
| Description: | TD sensor adjustment error 3: C During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | TD harness sensor disconnected, loose or defective Harness between TD sensor and drawer disconnected, defective • TD sensor defective, replace the PCU Note: The TD sensor cannot be replaced independently. The PCU must be replaced if the TD sensor is defective. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC375 |
| Description: | TD sensor adjustment error 4: Y During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | The voltage reading during process control for Vsg_reg was not within the correct range (4.0±0.5V). Vsg_reg is the voltage reading of the light reflected directly from the bare surface of the ITB. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC396 |
| Description: | Drum motor error 1: K When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Disconnected or defective motor harness. • Motor slips due to excessive load |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC397 |
| Description: | Drum motor error 2: M When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Disconnected or defective motor harness. • Motor slips due to excessive load |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC398 |
| Description: | Drum motor error 3: C When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Drum motor harness loose, broken, defective • Drum motor defective • DTMB defective |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC399 |
| Description: | Drum motor error 4: Y When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Drum motor harness loose, broken, defective • Drum motor defective • DTMB defective |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC400 |
| Description: | ID sensor error 1: Calibration Before adjustment Vsg_reg<0.5 but Vsg_reg could not be adjusted to the target Vsg_reg = 4.0±0.2V during process control. |
| Causes: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. |
| Remedy: | • ID sensor harness disconnected, loose, defective • ID sensor dirty • ID sensor defective • ITB unit drawer connector dirty |
| Error code: | SC410 |
| Description: | ID sensor error 2: Development γ K Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC411 |
| Description: | ID sensor error 3: Development γ M Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC412 |
| Description: | ID sensor error 4: Development γ C Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC413 |
| Description: | ID sensor error 5: Development γ Y Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC414 |
| Description: | ID sensor error 6: Development start voltage K The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC415 |
| Description: | ID sensor error 7: Development start voltage M The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC416 |
| Description: | ID sensor error 8: Development start voltage C The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC417 |
| Description: | ID sensor error 9: Development start voltage Y The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC418 |
| Description: | LED error during Vsg adjustment. PWM value: Ifsg>2000 This means the current to the LED of the ID sensor is abnormal. |
| Causes: | • ID sensor dirty • ID sensor defective |
| Remedy: | • ID sensor dirty • ID sensor defective |
| Error code: | SC420 |
| Description: | Potential sensor error 1: Vd Adjustment K The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC421 |
| Description: | Potential sensor error 2: Vd Adjustment M The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC422 |
| Description: | Potential sensor error 3: Vd Adjustment C The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC423 |
| Description: | Potential sensor error 4: Vd Adjustment Y The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC424 |
| Description: | Potential sensor error 5: Vl adjustment K Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC425 |
| Description: | Potential sensor error 6: Vl adjustment M Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC426 |
| Description: | Potential sensor error 7: Vl adjustment C Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC427 |
| Description: | Potential sensor error 8: Vl adjustment Y Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC432 |
| Description: | Potential sensor error 1: Vr K Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC433 |
| Description: | Potential sensor error 2: Vr M Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC434 |
| Description: | Potential sensor error 3: Vr C Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC435 |
| Description: | Potential sensor error 4: Vr Y Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC436 |
| Description: | Potential sensor error 5: Vd K The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC437 |
| Description: | Potential sensor error 6: Vd M The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC438 |
| Description: | Potential sensor error 7: Vd C The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC439 |
| Description: | Potential sensor error 8: Vd Y The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC440 |
| Description: | Image transfer power pack error 1: K An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC441 |
| Description: | Image transfer power pack error 2: M An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC442 |
| Description: | Image transfer power pack error 3: C An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC443 |
| Description: | Image transfer power pack error 4: Y An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC445 |
| Description: | Image transfer motor error The control board of the image transfer motor generated signals that indicate there is problem with the image transfer motor. |
| Causes: | • Defective ITB contact motor • Defective ITB contact sensor • Defective ITB unit |
| Remedy: | • Image transfer motor defective • ITB control board defective • ITB overloaded • Encoder strip on the front edge of the belt damaged. |
| Error code: | SC446 |
| Description: | ITB lift motor error The state of the ITB lift sensor does not change its state (switching from OFF to ON or vice versa), even after the ITB lift motor starts rotating. |
| Causes: | The transfer belt drive motor failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • ITB lift sensor dirty, disconnected, defective • ITB lift motor disconnected, defective |
| Error code: | SC450 |
| Description: | Transfer power pack output error An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the power pack 250 times at 2nd transfer output within 500 ms. |
| Causes: | • Damaged insulation on the high-voltage supply cable • Damaged insulation around the highvoltage power supply. • Check SIOB harness connections • SIOB defective |
| Remedy: | • Damaged insulation on the high-voltage supply cable • Damaged insulation around the highvoltage power supply. |
| Error code: | SC455 |
| Description: | PTR motor error The lock signal from the paper transfer motor is not detected within 1 sec. after the motor switched ON. |
| Causes: | • Motor disconnected • PTR shaft locked, needs cleaning, blocked by obstruction • Drive shaft of the ITB locked and overloaded, needs cleaning, or blocked by obstruction • DRB disconnected, defective |
| Remedy: | • Motor disconnected • PTR shaft locked, needs cleaning, blocked by obstruction • Drive shaft of the ITB locked and overloaded, needs cleaning, or blocked by obstruction • DRB (motor drive board) disconnected, defective |
| Error code: | SC460 |
| Description: | Separation power pack output error An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the power pack 250 times at D(AC) within 500 ms. |
| Causes: | • Damaged insulation on the high-voltage supply cable (replace cable) • Damaged insulation around the transfer power pack |
| Remedy: | • Damaged insulation on the high-voltage supply cable • Damaged insulation around the highvoltage power supply. 1. Replace the high-voltage supply cable. 2. Replace the high-voltage power supply unit. 3. Replace the IOB. |
| Error code: | SC484 |
| Description: | Waste toner bottle full The toner full sensor goes HIGH for more than 500 ms, indicating that the waste toner bottle is full. |
| Causes: | • Remove the used toner bottle • Empty the used toner bottle and reinstall it |
| Remedy: | • Remove waste toner bottle, empty it |
| Error code: | SC485 |
| Description: | Waste toner transport motor error The lock signal of the waste toner transport motor remains HIGH for more than 600 ms. |
| Causes: | The used toner transport motor failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • Waste toner transport motor defective |
| Error code: | SC487 |
| Description: | Waste toner bottle set error The set sensor of the waste toner bottle remains LOW for more than 500 ms. (The sensor goes HIGH when the bottle is installed correctly.) |
| Causes: | • Used toner bottle not installed • Remove used toner bottle and reinstall correctly |
| Remedy: | • Install the waste toner bottle • Remove waste toner bottle and reinstall correctly |
| Error code: | SC488 |
| Description: | Waste toner transport lock Waste toner cannot be transported to the waste toner bottle. |
| Causes: | Used toner is not being moved to the used toner bottle. |
| Remedy: | • Blockage in the line to the waste toner bottle |
| Error code: | SC496 |
| Description: | MUSIC sensor error The MUSIC sensor detected an abnormal pattern on the ITB because: • A/D converter exceeded upper or lower limit. • The pattern used to calculate the amount of skew is abnormal. • The reading of the pattern exceeded the length of time the LED projected light. • LED light could not be adjusted correctly. |
| Causes: | This SC is issued if one or more of the following occurred: • MUSIC sensor sampling abnormal • Sensor LED adjustment abnormal • Number of patches abnormal • ITB scratched • Main scan registration abnormal • Sub scan registration abnormal • Main scan magnification abnormal • Main scan magnification error diffusion abnormal • Lens refraction abnormal |
| Remedy: | • MUSIC sensor defective or disconnected • MUSIC pattern abnormal; do a forced process control (SP3821) and check the result (section 4.2.4). |
| Error code: | SC497 |
| Description: | Temperature and humidity sensor error 1: PCU The thermistor output of the temperature and humidity sensor above the black PCU was not within the prescribed range (0.5V to 4.2V) |
| Causes: | The machine detected one of these problems with the temperature/humidity sensor located under the rear end of the K PCDU: • The temperature sensor output was less than 0.5V or more than 2.8V three times in one minute, indicating a problem with the temperature detection. • The humidity sensor output was more than 2.4V for three times in one minute, indicating a problem with humidity detection. |
| Remedy: | • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective |
| Error code: | SC498 |
| Description: | Temperature and humidity sensor error 2 The thermistor output of the temperature and humidity sensor at below the waste toner bottle was not within the prescribed range (0.5V to 4.2V) |
| Causes: | The machine detected one of these problems with the temperature/humidity sensor located under the rear end of the K PCDU: • The temperature sensor output was less than 0.5V or more than 2.8V three times in one minute, indicating a problem with the temperature detection. • The humidity sensor output was more than 2.4V for three times in one minute, indicating a problem with humidity detection. |
| Remedy: | • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective |
| Error code: | SC503 |
| Description: | Tray 1 feed error • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC504 |
| Description: | Tray 2 feed error • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC505 |
| Description: | Tandem tray rear fence motor error • The return sensor does not switch ON within 10 sec. after the rear fence motor switches ON. • The HP sensor does not switch ON 10 sec. after the rear fence motor switches ON. • The HP sensor and return sensor switch ON at the same time. |
| Causes: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty |
| Remedy: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty |
| Error code: | SC506 |
| Description: | Tandem tray back fence motor error. The back fence should be closed but the fence was not detected in the closed position within 500 ms. -or- The back fence should be open but the fence was not detected in the open within 500 ms. |
| Causes: | The tray lift motor, pick-up solenoid, lift sensor, or lower limit sensor did not operate correctly. |
| Remedy: | • Paper loaded incorrectly • Back fence motor harness disconnected, loose, defective • Back fence motor defective • Paper blocking sensors • Paper stuck between tray and motor • Back fence close, back fence open sensor harnesses disconnected, loose, or defective. • Back fence close, back fence open sensor defective • Paper or other obstacle is interfering with movement of the fence |
| Error code: | SC510 |
| Description: | LCT tray error. • When the bottom plate is lifted, the upper limit sensor does not come on for 30 sec. • When the bottom plate is lowered, the lower limit sensor does not come on for 30 sec. • After lift begins, the upper limit sensor does not switch ON before the pick-up solenoid switches ON. • The paper end sensor switches ON during lift and the upper limit sensor does not switch ON for 2.5 s, and a message prompts user to reset paper. |
| Causes: | • Tray lift motor harness, disconnected, loose, or defective • Tray lift motor defective • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Remedy: | • Tray lift motor harness, disconnected, loose, or defective • Tray lift motor defective • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Error code: | SC515 |
| Description: | Duplex jogger motor error 1. When the jogger fence moves to the home position, the jogger fence HP sensor does not switch on even after the duplex jogger motor has moved the jogger fence 153.5 mm. |
| Causes: | The CIS cleaning fan motor in the right drawer failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors or motor • Return sensor or HP sensor defective or dirty |
| Error code: | SC516 |
| Description: | Duplex jogger motor error 2. When the jogger fence moves from the home position, the jogger fence HP sensor does not turn off even if the duplex jogger motor has moved the jogger fence 153.5 mm. |
| Causes: | A LOW motor LOCK signal was not detected after the motor switched off after 10 consecutive attempts. |
| Remedy: | • Paper or other obstacle has jammed mechanism • HP sensor connector disconnected or defective • HP sensor defective |
| Error code: | SC530 |
| Description: | Fan error 1: fusing cooling fan motor. The BICU does not receive the lock signal 5 seconds after the fusing unit fan switches ON. |
| Causes: | • Disconnected or defective motor harness. • Defective LSU fan motor |
| Remedy: | • Fusing cooling fan disconnected, defective • BICU defective |
| Error code: | SC531 |
| Description: | Fan error 2: fusing cooling fan motor. The lock signal remained HIGH for 5 sec. while the fan at the front of the fusing unit near the heat dissipation fins was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective LSU fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC532 |
| Description: | Fan error 3: PCB box fan. The lock signal remained HIGH for 5 sec. while the fan that cools the printed circuit boards was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective air intake fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC533 |
| Description: | Fan error 4: fusing exhaust fan. The lock signal remained HIGH for 5 sec. while the fan that draws air out of the fusing unit was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective PSU fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC534 |
| Description: | Fan error 5: duplex exhaust fan. The lock signal remained HIGH for 5 sec. while the fan that draws air out of the duplex unit was operating. |
| Causes: | • Fan harness disconnected or damaged • Fan blocked by an obstruction • Fan damaged |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC541 |
| Description: | Heating roller thermistor 1 error 1: Poor connection. The temperature measured by the heating roller thermistor does not reach 130°C after 10 tries and 65 sec. have elapsed. |
| Causes: | • Disconnected thermistor • Defective harness connection |
| Remedy: | • Heating roller thermistor harness connection loose, disconnected, defective • Defective heating roller thermistor |
| Error code: | SC542 |
| Description: | Heating roller thermistor 1 error 2: No warmup. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects ready temperature. |
| Causes: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp |
| Remedy: | • Thermistor is bent, installed incorrectly • Defective heating roller thermistor • Heating roller fusing lamp broken Do SP5810 to cancel the SC fusing code. |
| Error code: | SC543 |
| Description: | Heating roller thermistor 1 error 3: Software - High temperature. The thermistor detected a temperature over 230°C. |
| Causes: | • Defective I/O control (EGB) • Defective EGB |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature out of control Do SP5810 to cancel the SC fusing code. |
| Error code: | SC544 |
| Description: | Heating roller thermistor 1 error 4: Hardware - High temperature. The thermistor detected a temperature over 260°C. |
| Causes: | The machine detected the CPU port LOW twice at 100 ms intervals and issued this SC. This check is always done to check for overheating, even if SC543 does not detect the problem. |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC545 |
| Description: | Heating roller thermistor 1 error 5: Lamp remains ON. After hot roller reaches warmup temperature, the fusing lamps remained ON at full capacity for 25 sec. after reaching the warmup temperature while the hot roller was not rotating. |
| Causes: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Error code: | SC546 |
| Description: | Heating roller thermistor 2 error 1: Thermistor disconnected. The temperature measured by the heating roller thermistor does not reach 0°C after 45 sec. and remains over this temperature for 10 readings. |
| Causes: | Unstable connector contact of fusing thermistor |
| Remedy: | • Loose connection of the heating roller thermistor • Defective heating roller thermistor |
| Error code: | SC547 |
| Description: | Zero cross error. When the main switch is turned ON, the machine checks how many zero-cross signals are generated within 500 ms. This SC code is issued if the number of zerocross signals detected is either more than 66 or less than 45 for 10 readings. Note: Zero cross signals, generated from an ac power supply, are used to generate a trigger pulses to control the applied power accurately. |
| Causes: | Defective fusing lamp relay |
| Remedy: | • Electrical noise on the power supply line • Fusing relay damaged: replace the PSU. Normally, this SC is cancelled if you do SP5810 to cancel the SC fusing code. |
| Error code: | SC548 |
| Description: | Heating roller thermistor 2 error 2: Failed to reach warmup temperature. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects warmup temperature. |
| Causes: | • Defective fusing lamp • Defective thermistor |
| Remedy: | • Thermistor is bent, installed incorrectly • Defective heating roller thermistor • Heating roller fusing lamp broken • Defective BICU |
| Error code: | SC549 |
| Description: | Heating roller thermistor 2 error 3: Software - High Temperature. The thermistor detected a temperature over 250°C. |
| Causes: | • Do SP5810 to cancel the SC fusing code. • TRIAC short, AC drive board defective • VBCU defective |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic. Do SP5810 to cancel the SC fusing code. |
| Error code: | SC550 |
| Description: | Heating roller thermistor 2 error 4: Hardware - High Temperature. The thermistor detected a temperature over 260°C. |
| Causes: | • Do SP5810 to cancel the SC fusing code. • TRIAC short, AC drive board defective • VBCU defective |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC551 |
| Description: | Pressure roller thermistor error 1. The temperature measured by the pressure roller thermistor does not reach 0°C for 200 sec. |
| Causes: | In the condition of relay ON, the end thermistor on the fusing detects less than 0 degrees Celsius for more than 5 seconds. |
| Remedy: | • Loose connection of the pressure roller thermistor • Defective pressure roller thermistor • Defective BICU Do SP5810 to cancel the SC fusing code. |
| Error code: | SC552 |
| Description: | Pressure roller thermistor error 2. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects ready temperature. |
| Causes: | • Defective or deformed non-contact thermistor • Incorrect power supply input at the main power socket |
| Remedy: | • Pressure roller thermistor harness loose, disconnected, defective • Pressure roller thermistor defective |
| Error code: | SC553 |
| Description: | Pressure roller thermistor error 3: Software -High temperature. The thermistor detected a temperature over 220°C. |
| Causes: | • Defective main board • Defective PSU |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC554 |
| Description: | Pressure roller thermistor error 4: Hardware - High temperature. The thermistor detected a temperature over 230°C. |
| Causes: | • Defective main board • Defective PSU • Defective fusing unit |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC555 |
| Description: | Pressure roller thermistor error 5: Lamp remains ON. After hot roller reaches warmup temperature, the pressure roller fusing lamp remains for 6 sec. while the hot roller is not rotating. |
| Causes: | The fusing lamp reached the warm-up temperature and then attained fusing temperature (full power), but remained on after paper passed through the fusing unit (hot roller was not rotating). |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken Do SP5810 to cancel the SC fusing code. |
| Error code: | SC556 |
| Description: | Heating roller thermistor 2 error 5: Lamp remains ON. After hot roller reaches warmup temperature, the pressure roller fusing lamp remains for 6 sec. while the hot roller is not rotating. |
| Causes: | More than 1 degree Celsius temperature difference (between Center – End thermistor) is detected for 1.5 seconds 5 times in a row. |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Error code: | SC561 |
| Description: | Hot roller thermistor error 1: Thermistor disconnected. The temperature measured by the hot roller thermistor does not reach the prescribed warm-up temperature within 100 sec. |
| Causes: | Temperature detected at less than 0°C. Note: These are the two NC sensors on the side of the fusing unit. |
| Remedy: | • Loose connection of the hot roller thermistor • Defective hot roller thermistor • Defective BICU |
| Error code: | SC562 |
| Description: | Hot roller thermistor error 2: Failure to reach warmup temperature. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects ready temperature. |
| Causes: | Fusing temperature control failed to achieve the warm-up temperature. Note: These are the two NC sensors on the side of the fusing unit. |
| Remedy: | • Hot roller fusing lamp broken • Defective hot roller thermistor • Defective BICU. Do SP5810 to cancel the SC fusing code. |
| Error code: | SC563 |
| Description: | Hot roller thermistor error 3: Software - High Temperature. The thermistor detected a temperature over 250°C 10 times within 1 sec. |
| Causes: | Temperature incorrect due to a TRIAC short or other problem with IOB or AC drive board |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC564 |
| Description: | Hot roller thermistor error 4: Hardware - High Temperature. The thermistor detected a temperature over 260°C. |
| Causes: | Temperature incorrect due to a TRIAC short or other problem with IOB or AC drive board |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC565 |
| Description: | Hot roller thermistor error 5: Lamp remains ON. After hot roller reaches warmup temperature, the hot roller fusing lamp remains for 6300 sec. while the hot roller is not rotating. |
| Causes: | • Do SP5810 to cancel the SC fusing code. • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken Do SP5810 to cancel the SC fusing code. |
| Error code: | SC620 |
| Description: | ARDF communication error. A BREAK signal occurs after the machine detects the ARDF, or a communication timeout occurs. |
| Causes: | No response from the ADF after connection to the main machine or an error occurred after connection. |
| Remedy: | • ARDF disconnected • IPU board harness disconnected, defective • IPU board defective • Spurious noise from the power supply line • ARDF control board defective |
| Error code: | SC621 |
| Description: | Mailbox-to-Finisher communication error. Communication between the mailbox and finisher is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | The UART generated an error when the finisher was connected. |
| Remedy: | • Connection cable between mailbox and finisher disconnected, defective • Finisher main board defective • BICU defective • PSU defective |
| Error code: | SC622 |
| Description: | LCT communication error. Communication between the copier and LCT is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | • Paper tray control board defective • BCU defective • IOB defective • Paper tray-main machine connection error |
| Remedy: | • Connection cable between the LCT and copier is disconnected, defective • LCT main board defective • BICU defective • PSU defective |
| Error code: | SC624 |
| Description: | Mailbox-to-copier communication error. Communication between the mailbox and copier is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | • Mailbox cable disconnected, defective • Mailbox main board defective • VBCU defective • PSU defective |
| Remedy: | • Mailbox cable disconnected, defective • Mailbox main board defective • BICU defective • PSU defective |
| Error code: | SC630 |
| Description: | RSS communication error. An error was detected in communication via RSS between the machine and the RSS center. Error occurred on a public line at the RSS terminal. |
| Remedy: | • No action required |
| Error code: | SC632 |
| Description: | Key/card counter device error 1. After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • The serial line from the device to the copier is unstable, disconnected, or defective. |
| Remedy: | • The serial line from the device to the copier is unstable, disconnected, or defective. |
| Error code: | SC633 |
| Description: | Key/card counter device error 2. During communication with the device, the BICU received a break (Low) signal. |
| Causes: | • The serial line from the device to the copier is unstable, disconnected, or defective. |
| Remedy: | • The serial line from the device to the copier is unstable, disconnected, or defective. |
| Error code: | SC634 |
| Description: | Key/card counter device error 3. After installation of the device, a message alerts user to a backup RAM error. |
| Causes: | •X Counter device control board defective •X Backup battery of counter device defective |
| Remedy: | • Device control board defective • Device control board backup battery defective |
| Error code: | SC635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Remedy: | • Device control board defective • Device control board backup battery defective |
| Error code: | SC670 |
| Description: | Engine startup error. • Engine does not respond within 30 s after power ON. • Engine down detected suddenly during power ON and warmup. |
| Causes: | The engine failed to communicate with the firmware. Firmware update failure. |
| Remedy: | • BICU installation incorrect • BICU defective • Sudden communication reset occurred between the BICU and the controller. |
| Error code: | SC672 |
| Description: | GW controller startup error. • After power ON, the line between the GW controller and the operation panel did not open for normal operation. • After normal startup, communication with the GW controller stopped. |
| Causes: | • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector loose, broken, or defective • Controller late |
| Remedy: | • GW Controller stalled • GW Controller installed incorrectly • GW Controller board defective • Operation panel harness disconnected or defective |
| Error code: | SC680 |
| Description: | BICU-MUSIC communication error. The main CPU fails to communicate with the MUSIC CPU within 5 sec. and three attempts failed. |
| Causes: | • Toner cartridge memory chip loose connection • Memory chip problem • Memory chip cable wiring problem |
| Remedy: | • Toner cartridge ID chip harness disconnected, defective • Toner cartridge ID chip defective • Toner cartridge installed incorrectly • Toner cartridge defective • UART communication failure; replace the BICU |
| Error code: | SC687 |
| Description: | Memory address command error. The BICU does not receive a memory address command from the controller 120 seconds after paper is in the position for registration. |
| Causes: | The BICU did not receive a memory address command from the controller within the prescribed time after the paper reached the registration sensor. |
| Remedy: | • BICU-Controller connection loose, defective • BICU defective • Controller defective |
| Error code: | SC701 |
| Description: | Original pick-up operation error. Even though the pick-up motor is rotating clock-wise, the pick-up roller home position sensor cannot detect the position of the pickup roller. |
| Causes: | Even though the pickup motor is rotating clock-wise, the pickup roller home position sensor cannot detect the position of the pickup roller. |
| Remedy: | • Pick-up roller HP sensor harness loose, disconnected, defective • Pick-up roller HP sensor defective • Pick-up motor harness loose, disconnected, defective • Pick-up motor defective • ARDF control board defective |
| Error code: | SC705 |
| Description: | ARDF bottom plate lift motor. • The bottom plate HP sensor did not detect the home position of the bottom plate after the bottom plate lift motor switches ON and lowers the bottom plate. • The bottom plate position sensor does not detect the position of the plate after the lift motor switches ON and raises the bottom plate. |
| Causes: | The bottom plate HP sensor did not detect the home position of the bottom plate after the bottom plate lift motor switches on and lowers the bottom plate. The bottom plate position sensor does not detect the position of the plate after the lift motor switches on and raises the bottom plate. |
| Remedy: | • ARDF feed motor disconnected, defective • Bottom plate HP sensor disconnected, defective • ARDF main board defective |
| Error code: | SC720 |
| Description: | Finisher lower transport motor error. No encoder pulse signal is detected for the transport motor within the prescribed time. The 1st failure issues an original jam message, and the 2nd failure issues this SC code. |
| Causes: | • Harness short-circuit -80 only • Overload • Motor defective • Solenoid defective -03, -80 only • Connector disconnected • Encoder defective -10, -25, -34 -81 only • Home position sensor defective |
| Remedy: | • Lower transport motor disconnected, defective • Finisher connection to transport motor loose, defective • Lower transport motor defective • Finisher main board defective |
| Error code: | SC721 |
| Description: | Finisher jogger motor error. The jogger fences move out of the home position but the HP sensor output does not change within the specified number of pulses. The 1st failure issues an original jam message, and the 2nd failure issues this SC code. |
| Causes: | • Overcurrent (-03 only) • Staple jam (-44 only) • Encoder error (-11, -11, -25, -44) • Motor defective • Connecter disconnected, or loose • Motor overload • HP sensor defective • Paper surface sensor defective (-70 only) |
| Remedy: | • Jogger HP sensor disconnected, defective • Jogger motor disconnected, defective • Jogger motor overloaded due to obstruction • Finisher main board and jogger motor connection loose, defective • Finisher main board defective |
| Error code: | SC723 |
| Description: | Finisher feed-out motor. The stack feed-out belt HP sensor does not activate within the specified time after the stack feed-out belt motor turns ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The motor that drives the rotation of the positioning sponge roller is not operating. |
| Remedy: | • Stack feed-out HP sensor disconnected, defective • Feed-out motor disconnected, defective • Finisher main board connection to feed out motor disconnected, defective • Motor overload due to obstruction |
| Error code: | SC724 |
| Description: | Finisher stapler hammer motor error. Stapling does not finish within the prescribed time after the staple hammer motor turns ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The motor that lowers and raises the positioning roller above the stapling tray not operating. |
| Remedy: | • Stapler hammer motor overloaded due to obstruction, jammed staple, number of sheets exceeds limit for stapling • Stapler hammer motor disconnected, defective • Staple hammer motor HP sensor disconnected, defective |
| Error code: | SC725 |
| Description: | Finisher exit guide plate motor error. After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The motor that opens and closes the exit guide at the shift tray exit is not operating correctly. |
| Remedy: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Error code: | SC726 |
| Description: | Shift jogger motor 1 error. The sides fences do not retract within the prescribed time after the shift jogger motor switches ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The drag roller arm with the sponge roller did not return to its home position within the prescribed time. |
| Remedy: | • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective |
| Error code: | SC727 |
| Description: | Shift jogger motor 2 error. The side fences do not retract within the prescribed time after the shift jogger motor switches ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Error code: | SC728 |
| Description: | Shift jogger retraction motor error. The side fences do not retract within the prescribed time after the retraction motor switches ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The side fences at the exit of the finisher did not leave (or arrive at) their home positions within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Error code: | SC730 |
| Description: | Finisher Tray 1 shift motor error. The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Error code: | SC740 |
| Description: | Finisher corner stapler motor error. The stapler motor does not switch off within the prescribed time after operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The stapler motor did not switch off within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Remedy: | • Staple jam • Number of sheets in the stack exceeds the limit for stapling • Stapler motor disconnected, defective |
| Error code: | SC741 |
| Description: | Finisher corner stapler rotation motor error. The stapler does not return to its home position within the specified time after stapling. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The stapler did not return to its home position (or did not leave its home position) within the specified time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Stapler rotation motor disconnected, defective • Stapler rotation motor overloaded due to obstruction • Stapler rotation HP sensor disconnected, defective |
| Error code: | SC742 |
| Description: | Finisher stapler movement motor error. The stapler HP sensor is not activated within the specified time after the stapler motor turned ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The stapler did not return to its home position (or leave its home position) within the specified time after stapling. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Stapler movement motor disconnected, defective • Stapler movement motor overloaded due to obstruction • Stapler HP sensor disconnected, defective |
| Error code: | SC743 |
| Description: | Booklet stapler motor error 1. The front stapler unit saddlestitch motor does not start operation within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The booklet stapler motor did not start stapling within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Front motor disconnected, defective • Front motor overloaded due to obstruction |
| Error code: | SC744 |
| Description: | Booklet stapler motor error 2. The rear stapler unit saddlestitch motor does not start operation within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Rear motor disconnected, defective • Rear motor overloaded due to obstruction |
| Remedy: | • Rear motor disconnected, defective • Rear motor overloaded due to obstruction |
| Error code: | SC750 |
| Description: | Finisher tray 1 (upper tray lift) motor error. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The shift tray paper height sensor did not change its status within the prescribed time after the tray was raised or lowered. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Tray lift motor disconnected, defective • Upper tray paper height sensor disconnected, defective • Finisher main board connection to motor loose • Finisher main board defective |
| Error code: | SC751 |
| Description: | Finisher tray 2 (lower tray lift) motor error. The lower tray paper height sensor does not change its status with the specified time after the tray raises or lowers. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Tray lift motor disconnected, defective • Upper tray paper height sensor disconnected, defective • Finisher main board connection to motor loose • Finisher main board defective |
| Remedy: | • Tray lift motor disconnected, defective • Upper tray paper height sensor disconnected, defective • Finisher main board connection to motor loose • Finisher main board defective |
| Error code: | SC752 |
| Description: | Finisher pressure plate motor error. Pressure plate motor operating but the plate is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Pressure plate HP sensor disconnected, defective • Pressure plate motor disconnected, defective • Pressure plate motor overloaded due to obstruction |
| Remedy: | • Pressure plate HP sensor disconnected, defective • Pressure plate motor disconnected, defective • Pressure plate motor overloaded due to obstruction |
| Error code: | SC753 |
| Description: | Return roller motor error. Occurs during the operation of the lower tray pressure motor. |
| Causes: | The drag roller HP sensor did not detect the drag roller in (or out of) its home position within the prescribed time. (The drag drive motor drives the timing belt that rotates the drag roller at the shift tray exit.) |
| Remedy: | • Motor harness disconnected, loose, defective • Motor overloaded • Home position sensor harness disconnected, loose, defective • Home position defective |
| Error code: | SC760 |
| Description: | Finisher punch motor error. The punch HP sensor is not activated within the specified time after the punch motor turned ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The punch HP sensor did not detect the punch movement motor in (or out) of its home position within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Punch HP sensor disconnected, defective • Punch motor disconnected, defective • Punch motor overload due to obstruction |
| Error code: | SC761 |
| Description: | Finisher folder plate motor error. The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | 1. Over current of bridge unit motor 2. Over current due to short-circuit in PCB |
| Remedy: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Error code: | SC762 |
| Description: | Finisher pressure plate motor error. Pressure plate motor operating but the plate is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The punch switch motor failed to turn on within the specified time. |
| Remedy: | • Pressure plate HP sensor disconnected, defective • Pressure plate motor disconnected, defective • Pressure plate motor overloaded due to obstruction |
| Error code: | SC763 |
| Description: | Punch movement motor error. Occurs during operation of the punch unit. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The punch movement HP sensor did not detect the punch at its home position (or out of its home position) within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC764 |
| Description: | Paper position sensor slide motor error. Occurs during operation of the punch unit. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The system detected an error at the CIS (Contact Image Sensor) inside the punch unit during paper registration for paper punching. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC765 |
| Description: | Folding unit bottom fence lift motor. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The bottom fence in the booklet fold unit did not return to the home position within the specified time. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC766 |
| Description: | Clamp roller retraction motor error. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The clamp roller did not return to the home position within the specified time. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC767 |
| Description: | Stack junction gate motor error. Occurs during operation of the punch unit. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Stack junction mechanism overloaded due to an obstruction • Stack junction gate HP sensor connector loose, broken, defective • Stack junction gate HP sensor defective • Stack junction gate motor connector loose, broken, defective • Stack junction gate motor defective • Main control board defective |
| Remedy: | • Motor harness disconnected, loose, defective • Motor overload • Motor defective |
| Error code: | SC770 |
| Description: | Cover interposer tray bottom plate motor error. • After the motor starts to raise the bottom plate, the bottom plate position sensor does not detect the plate at the specified time (3 s). • After the motor starts to lower the bottom plate, the bottom plate HP sensor does not detect the bottom plate. |
| Causes: | In the first tray: • The upper limit sensor did not detect the bottom plate within the specified time after the lift motor switched on to lift the bottom plate. • The lower limit sensor did not direct the bottom plate within the specified time after the lift motor switched on to lower the bottom plate. Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code. |
| Remedy: | • Bottom plate position sensor, disconnected, defective • Bottom plate HP sensor disconnected, defective |
| Error code: | SC775 |
| Description: | Cover interposer tray feed motor |
| Causes: | The top fence HP sensor did not detect the top fence at (or out of) the home position within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor overload • Motor defective |
| Error code: | SC790 |
| Description: | Finisher staple waste hopper full. The staple waste hopper is full of cut staples. |
| Causes: | The jogger fence HP sensor failed to detect the jogger fence at the home position within the specified time. |
| Remedy: | • If the hopper is full, empty the hopper • If the hopper is not full, the hopper full sensor is disconnected, defective |
| Error code: | SC817 |
| Description: | Boot loader error. The boot loader cannot read one of the following: self-diagnostic module, kernel, or one of the files of the root file system, or the check of one of these items on the system SD card failed. |
| Causes: | • File or module on the system SD card is corrupted • File or module on the system SD card is illegal • Make sure that the system SD card is the one designed for the machine • Replace controller board. |
| Remedy: | • File or module on the system SD card is corrupted • File or module on the system SD card is illegal • Make sure that the system SD card is the one designed for the machine • Replace system ROM on the controller board |
| Error code: | SC818 |
| Description: | Watchdog error. While the system program is running, a bus hold or interrupt program goes into an endless loop, preventing any other programs from executing. |
| Causes: | • System program defective; switch off/on, or change the controller firmware if the problem cannot be solved • Controller board defective • Replace the peripheral device |
| Remedy: | • System program defective; switch OFF/ON, or change the controller firmware if the problem cannot be solved • Controller board defective • Controller option malfunction |
| Error code: | SC819 |
| Description: | Fatal kernel error. Due to a control error, a RAM overflow occurred during system processing. One of the following messages was dis |
| Causes: | • Controller board defective |
| Remedy: | • System program defective • Controller board defective • Optional board defective • Replace controller firmware 0x696e init died 0x766d vm_pageout: Virtual Memory is full 4361 Cache Error NOTE: For more details about this SC code error, execute SP5990 to print an SMC report so you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | SC821 |
| Description: | Self-diagnostic error 1: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • ASIC (controller board defective) |
| Error code: | SC822 |
| Description: | Self-diagnostic error 2: HDD |
| Error code: | SC824 |
| Description: | Self-diagnostic error 4: NVRAM NVRAM device does not exist, NVRAM device is damaged, NVRAM socket damaged |
| Causes: | • Controller board detective |
| Remedy: | • NVRAM defective • Controller board defective • NVRAM backup battery exhausted • NVRAM socket damaged |
| Error code: | SC826 |
| Description: | Self-diagnostic Error: NVRAM (RTC Option) If this NVRAM is installed, the difference between the 1 second measurement of RTC and 1 second CPU timer exceeds the allowable limit. |
| Causes: | • RTC device error |
| Error code: | SC828 |
| Description: | Self-diagnostic error 7: ROM • Measuring the CRC for the boot monitor and operating system program results in an error. • A check of the CRC value for ROMFS of the entire ROM area results in an error. |
| Causes: | A firmware type error or checksum error occurred. |
| Remedy: | • Software defective • Controller board defective • ROM defective NOTE: For more details about this SC 833, SC834 error, execute SP5990 to print an SMC report so you can read the error code. The error code is not displayed on the operation panel. The additional error codes (0F30, 0F31, etc. are listed in the SMC report. |
| Error code: | SC833 |
| Description: | Self-diagnostic error 8: Engine I/F ASIC |
| Remedy: | 0F30 0F31 ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. • Replace the mother board 0F41 The read/write check done for resident RAM on the mother board could not be done correctly. • Replace the mother board 50B1 Could not initialize or read the bus connection. • Check for loose connections at the mother board. • Replace the mother board 50B2 Value of the SSCG register is incorrect. • Check for loose connections at the mother board. • Replace the mother board |
| Error code: | SC834 |
| Description: | Self-diagnostic error 9: Optional Memory RAM DIMM 5101 The write/verify check for the optional RAM chip on the engine mother board gave an error. |
| Causes: | • Controller defective |
| Remedy: | • Controller defective • Mother board defective |
| Error code: | SC850 |
| Description: | Net I/F error. • Duplicate IP addresses. • Illegal IP address. • Driver unstable and cannot be used on the network. |
| Causes: | • IP address setting incorrect • Ethernet board defective • Controller board defective |
| Remedy: | • IP address setting incorrect • Ethernet board defective • Controller board defective |
| Error code: | SC851 |
| Description: | IEEE 1394 I/F error. Driver setting incorrect and cannot be used by the 1394 I/F. |
| Causes: | Driver setting incorrect and cannot be used by the 1394 I/F. |
| Remedy: | • NIB (PHY), LINK module defective; change the Interface Board • Controller board defective |
| Error code: | SC853 |
| Description: | Wireless LAN Error 1. During machine start-up, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | During machine start-up, the machine can access the board that holds the wireless LAN (Bluetooth), but not access the wireless LAN card. |
| Remedy: | • Wireless LAN card missing (was removed) |
| Error code: | SC854 |
| Description: | Wireless LAN Error 2. During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | The board that holds the wireless LAN card (Bluetooth) could be accessed, but the wireless LAN card could not be accessed while the machine was operating. |
| Remedy: | • Wireless LAN card missing (was removed) |
| Error code: | SC855 |
| Description: | Wireless LAN error 3. An error was detected on the wireless LAN card (802.11b or Bluetooth). |
| Causes: | An error was detected for the wireless LAN card (802.11b or Bluetooth). |
| Remedy: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | SC856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN card (802.11b or Bluetooth). |
| Causes: | An error was detected for the wireless LAN board (Bluetooth). |
| Remedy: | • Wireless LAN card defective • PCI connector (to the mother board) loose |
| Error code: | SC857 |
| Description: | USB I/F Error. The USB driver is not stable and caused an error. |
| Causes: | The USB driver is unstable and generated an error. |
| Remedy: | • Bad USB card connection • Replace the controller board |
| Error code: | SC860 |
| Description: | HDD startup error at main power ON. • HDD is connected but a driver error is detected. • The driver does not respond with the status of the HDD within 30 s. |
| Causes: | HDD is connected but a driver error is detected, or the driver did not respond with the status of the HDD within 30 s. |
| Remedy: | • HDD is not formatted • Label name input during formatting is corrupted; format the hard disk again • HDD is defective |
| Error code: | SC861 |
| Description: | HDD re-try failure. At power ON with the HDD detected, power supply to the HDD is interrupted, after the HDD is awakened from the sleep mode, the HDD is not ready within 30 s. |
| Causes: | At power on with the HDD detected, power supply to the HDD is interrupted, after the HDD is awakened from the sleep mode, the HDD is not ready within 30 s. |
| Remedy: | • Harness between HDD and board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | SC863 |
| Description: | HDD data read failure. The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Remedy: | • HDD defective Note: If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM, and the next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. |
| Error code: | SC864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to an CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | During HDD operation, the HDD cannot respond to an CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Remedy: | • HDD defective |
| Error code: | SC865 |
| Description: | HDD access error. HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Remedy: | • HDD defective. |
| Error code: | SC866 |
| Description: | SD card error 1: Confirmation. The machine detects an electronic license error in the application on the SD card in the controller slot immediately after the machine is turned ON. The program on the SD card contains electronic confirmation license data. If the program does not contain this license data, or if the result of the check shows that the license data in the program on the SD card is incorrect, then the checked program cannot execute and this SC code is displayed. |
| Causes: | The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. Note: • The program on the SD card contains electronic confirmation license data. • If the program does not contain this license data, or if the result of the check shows that the license data in the program on the SD card is incorrect, then the checked program cannot execute and this SC code is displayed. |
| Remedy: | • Program missing from the SD card • Download the correct program for the machine to the SD card |
| Error code: | SC867 |
| Description: | SD card error 2: SD card removed. The SD card in the boot slot when the machine was turned on was removed while the machine was ON. |
| Causes: | An application SD card has been removed from the slot (mount point of /mnt/sd*). |
| Remedy: | • Insert the SD card, then turn the machine OFF and ON. |
| Error code: | SC868 |
| Description: | SD card error 3: SD card access. An error occurred while an SD card was used. |
| Causes: | • SD card defective • SD controller defective |
| Remedy: | • SD card not inserted correctly • SD card defective • Controller board defective Note: If you want to try to reformat the SD card, use SD Formatter Ver 1.1. |
| Error code: | SC870 |
| Description: | Address book data error. Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Software bug • Inconsistency of Address Book source location (machine/delivery server/LDAP server) • Inconsistency of Address Book encryption setting or encryption key (NVRAM was replaced individually without formatting the Address Book) • Address Book storage device (SD) was temporarily removed or hardware configuration does not match the application configuration. • Address Book data corruption was detected. |
| Remedy: | • Software defective. Turn the machine OFF/ON. If this is not the solution for the problem, then replace the controller firmware. • HDD defective. More Details • Do SP5846 050 (UCS (User info control service) Settings – Initialize all Directory Info.) to reset all address book data. • Reset the user information with SP5832 006 (HDD Formatting– User Information). • Replace the HDDs. • Boot the machine from the SD card. |
| Error code: | SC873 |
| Description: | HDD mail send data error. An error was detected on the HDD immediately after the machine was turned ON, or power was turned OFF while the machine used the HDD. |
| Causes: | An error was detected on the HDD immediately after the machine was turned on, or power was turned of while the machine was using the HDD. |
| Remedy: | • Do SP5832-007 (Format HDD – Mail TX Data) to initialize the HDD. • Replace the HDD |
| Error code: | SC874 |
| Description: | Delete All error 1: HDD. A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit (B735) running from an SD card. |
| Causes: | • Error detected in HDD data delete program • Error detected in NVRAM data delete program • The "Delete All" option was not set |
| Remedy: | • Turn the main switch OFF/ON and try the operation again. • Install the Data Overwrite Security Unit again. For more, see section “1. Installation”. • HDD defective |
| Error code: | SC875 |
| Description: | Delete All error 2: Data area. An error occurred while the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B660 running from an SD card. |
| Causes: | • HDD logical formatting failed. • The modules failed to erase data. |
| Remedy: | • Turn the main switch OFF/ON and try the operation again. |
| Error code: | SC880 |
| Description: | File Format Converter (MLB) error. A request to get access to the MLB was not answered within the specified time. |
| Causes: | • MLB defective, replace the MLB |
| Remedy: | • MLB defective, replace the MLB |
| Error code: | SC900 |
| Description: | Electrical total counter error. The total counter contains something that is not a number. |
| Causes: | The total counter contains data that is not a number. |
| Remedy: | • NVRAM incorrect type • NVRAM defective • NVRAM data scrambled • Unexpected error from external source |
| Error code: | SC920 |
| Description: | Printer error 1. An internal application error was detected and operation cannot continue. |
| Causes: | • The software’s bug • Unexpected hardware configuration such as insufficient memory |
| Remedy: | • Software defective; turn the machine OFF/ON, or change the controller firmware • Insufficient memory |
| Error code: | SC921 |
| Description: | Printer error 2. When the application started, the necessary font was not on the SD card. |
| Causes: | When the printer application started, the specified font could not be found on the SD card. |
| Remedy: | • Font not on the SC card |
| Error code: | SC925 |
| Description: | Net File function error. The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue. The HDDs are defective and they cannot be debugged or partitioned, so the Scan Router functions (delivery of received faxes, document capture, etc.), Web services, and other network functions cannot be used. HDD status codes are displayed below: |
| Causes: | The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue. The HDDs are defective and they cannot be debugged or partitioned, so the Scan Router functions (delivery of received faxes, document capture, etc.), Web services, and other network functions cannot be used. HDD status codes are displayed below the SC code: |
| Remedy: | Procedure 1 If the machine shows SC codes for HDD errors (SC860 ~ SC865) with SC 925, do the recovery procedures for SC860 ~ SC865. Procedure 2 If the machine does not show one of the five HDD errors (SC860 ~ SC865), turn the machine power OFF and ON. If this is not the solution for the problem, then initialize the NetFile partition on the HDD with SP5832-011 (HDD Formatting). NetFiles: Jobs printed from the document server using a PC and DeskTopBinder • Before you initialize the NetFile partition on the HDD, tell the customer that: • Received faxes on the delivery server will be erased • All captured documents will be erased • DeskTopBinder job history will be erased • Documents on the document server, and scanned documents, will not be erased. • The first time that the network gets access to the machine, the management information must be configured again (this will use a lot of time). Before you initialize the Netfile partition with SP5832-011, do these steps: 1. Go into the User Tools mode and do “Delivery Settings” to print all received fax documents that are scheduled for delivery. Then erase them. 2. In the User Tools mode, do Document Management> Batch Delete Transfer Documents. 3. Do SP5832-011, then turn the machine power OFF and ON. Procedure 3 If “Procedure 2” is not the solution for the problem, do SP5832-001 (HDD Formatting – All), then turn the machine power OFF and ON. SP5832-001 erases all document and address book data on the hard disks. Ask the customer before you do this SP code. Procedure 4 If “Procedure 3” is not the solution for the problem, replace the HDD. |
| Error code: | SC990 |
| Description: | Software error 2 The software performs an unexpected function and the program cannot continue. |
| Causes: | An unexpected operation was encountered by the software. |
| Remedy: | • Software defective, re-boot 1) Execute SP7403 or print an SMC Report (SP5990) to read the history of the 10 most recent logged errors. 2) If you press the zero key on the operation panel with the SP selection menu displayed, you will see detailed information about the recently logged SC990 or SC991, including the software file name, line number, and so on. 1) is the recommended method, because another SC could write over the information for the previous SC. |
| Error code: | SC991 |
| Description: | Software error 3 The software performs an unexpected function and the program cannot continue. However, unlike SC990, recovery processing allows the program to continue. |
| Causes: | The software peformed an unexpected function and the program cannot continue. Recovery processing allows the program to continue. |
| Remedy: | • Software defective, re-boot 1) Execute SP7403 or print an SMC Report (SP5990) to read the history of the 10 most recent logged errors. 2) If you press the zero key on the operation panel with the SP selection menu displayed, you will see detailed information about the recently logged SC990 or SC991, including the software file name, line number, and so on. 1) is the recommended method, because another SC could write over the information for the previous SC. |
| Error code: | SC992 |
| Description: | Software error 4: Undefined An error not controlled by the system occurred (the error does not come under any other SC code). |
| Causes: | An error not controlled by the system occurred (the error does not come under any other SC code). |
| Remedy: | • Software defective • Turn the machine power OFF and ON. The machine cannot be used until this error is cleared. |
| Error code: | SC997 |
| Description: | Cannot select application function An application does not start after the user pushed the correct key on the operation panel. |
| Causes: | An application did not start after pressing the appropriate key on the operation panel. |
| Remedy: | • Software bug • A RAM or DIMM option necessary for the application is not installed or not installed correctly. |
| Error code: | SC998 |
| Description: | Application cannot start Register processing does not operate for an application within 60 s after the machine power is turned ON. No applications not start correctly, and all end abnormally. |
| Causes: | Register processing did not execute for an application within 60 sec. after the machine was switched on. No applications start correctly, and all end abnormally. |
| Remedy: | • Software bug • A RAM or DIMM option necessary for the application is not installed or not installed correctly. |
