Ricoh CL5000
Рейтинг
Модули
ELECTRICAL SECTION 2
FUSING UNIT 2
PCU SECTION
FRAME SECTION
PAPER CASSETTE
ELECTRICAL SECTION 3
EXTERIOR 1
PAPER EXIT SECTION
DEVELOPMENT SECTION
PAPER REGISTRATION
Drive Section 1
Vertical Transport 2
ELECTRICAL SECTION 1
BY-PASS FEED UNIT 2
EXTERIOR 2
FUSING UNIT 1
DRIVE SECTION 3
DRIVE SECTION 2
BY-PASS FEED UNIT 1
LD unit
Детали ELECTRICAL SECTION 2
| Деталь: | I/O Board |
| Парткод: | G070 5214 |
| Деталь: | I/O Base Bracket |
| Парткод: | G070 5531 |
| Деталь: | Harness - Bcu-iob |
| Парткод: | G070 5301 |
| Деталь: | Toner End Sensor Harness |
| Парткод: | G070 5305 |
| Деталь: | Intermediate Transfer Harness |
| Парткод: | G070 5311 |
| Деталь: | BCU Board |
| Парткод: | G070 5120 |
| Деталь: | SPRING HOLDER |
| Парткод: | G070 4320 |
| Деталь: | Spring - Oil Supply Roller |
| Парткод: | AA06 3895 |
| Деталь: | Spring Plate - Oil Supply Roller |
| Парткод: | G070 4317 |
| Деталь: | Terminal Cover - Oil Supply Roller |
| Парткод: | G070 4316 |
| Деталь: | Holder - Oil Supply roller |
| Парткод: | G070 4313 |
| Деталь: | Roller Terminal - Oil Supply |
| Парткод: | G070 4314 |
| Деталь: | High Voltage Harness |
| Парткод: | G070 5368 |
| Деталь: | Connector bracket |
| Парткод: | G070 4310 |
| Деталь: | AC Harness - Fusing Unit (120V) |
| Парткод: | G070 5323 |
| Деталь: | AC Harness - Fusing Unit (230V) |
| Парткод: | G070 5360 |
| Деталь: | BCU Bracket |
| Парткод: | G070 5516 |
| Деталь: | Power Supply Unit - 120V |
| Парткод: | AZ23 0101 |
| Деталь: | Power Supply Unit - 230V |
| Парткод: | G070 5057 |
| Деталь: | Power Supply Unit Cover |
| Парткод: | G070 5503 |
| Деталь: | FLAT CABLE COVER |
| Парткод: | G070 1981 |
| Деталь: | DC Power Supply Harness |
| Парткод: | G070 5365 |
| Деталь: | Harness - Bcu-ppi |
| Парткод: | G070 5302 |
| Деталь: | Relay Harness - Operation Panel |
| Парткод: | G070 5319 |
| Деталь: | Bank Relay Harness |
| Парткод: | G070 5341 |
| Деталь: | Fusing Unit - Fusing Belt Assembly |
| Парткод: | G070 4005 |
| Деталь: | Thermistor Holder |
| Парткод: | G070 4051 |
| Деталь: | Fusing Lamp - 120V 770W |
| Парткод: | AX44 0161 |
| Деталь: | Fusing Lamp - 230V 770W |
| Парткод: | AX44 0162 |
| Деталь: | Fusing Lamp - 120V 350W |
| Парткод: | AX43 0078 |
| Деталь: | Fusing Lamp - 230V 350W |
| Парткод: | AX43 0079 |
| Деталь: | Pressure Thermistor |
| Парткод: | AW10 0061 |
| Деталь: | Oil End Sensor |
| Парткод: | G024 4740 |
| Деталь: | Fusing Knob |
| Парткод: | G070 4147 |
| Деталь: | Spring - Oiling Roller |
| Парткод: | AA06 3865 |
| Деталь: | Bushing -4x8x8.5 |
| Парткод: | AE03 1054 |
| Деталь: | Bushing -4x9x13 |
| Парткод: | AE03 1055 |
| Деталь: | Rubber Shield - 4x8x3 |
| Парткод: | G070 4087 |
| Деталь: | Gear - 36Z |
| Парткод: | AB01 1436 |
| Деталь: | BELT TENSION SPRING |
| Парткод: | AA06 0875 |
| Деталь: | Belt Tension Lever |
| Парткод: | G070 4116 |
| Деталь: | Front Stopper - Oil Supply Unit |
| Парткод: | G070 4114 |
| Деталь: | Sensor Holder |
| Парткод: | G070 4118 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Rear Stopper - Oil Supply Unit |
| Парткод: | G070 4152 |
| Деталь: | Ball Bearing - 20x32x7 |
| Парткод: | AE03 0050 |
| Деталь: | Pressure Roller - Assembly |
| Парткод: | AE02 0119 |
| Деталь: | Gear - 47Z |
| Парткод: | AB01 1435 |
| Деталь: | Idler Gear - 28Z/35Z |
| Парткод: | AB01 7570 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | G070 4052 |
| Деталь: | Lower Pressure Roller Stay |
| Парткод: | G070 4050 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0876 |
| Деталь: | Front Oil Tank Absorber |
| Парткод: | G070 4073 |
| Деталь: | Oil Tank - Pressure Sub-unit |
| Парткод: | G070 4069 |
| Деталь: | Rear Oil Pan - Pressure Unit |
| Парткод: | G070 4063 |
| Деталь: | Rear Oil Absorber |
| Парткод: | G070 4066 |
| Деталь: | Spring Plate - Pressure Unit |
| Парткод: | G070 4064 |
| Деталь: | Front Oil Pan - Pressure Unit |
| Парткод: | G070 4062 |
| Деталь: | Front Oil Absorber |
| Парткод: | G070 4065 |
| Деталь: | Oil Tank Absorber - Long |
| Парткод: | G070 4074 |
| Деталь: | Oil Supply Roller - Oil Supply |
| Парткод: | AE04 0050 |
| Деталь: | Oil Apply Roller - Oil Supply |
| Парткод: | AE04 0037 |
| Деталь: | Heat Insulation - Sensor Holder |
| Парткод: | G070 4120 |
| Деталь: | Front Oil Tank Absorber |
| Парткод: | G070 4072 |
| Деталь: | Roller Clutch - 4mm |
| Парткод: | B051 4138 |
| Деталь: | Torsion Spring - Rear |
| Парткод: | B051 4118 |
| Деталь: | Torsion Spring - Front |
| Парткод: | B051 4120 |
| Деталь: | Charge Corona Assembly |
| Парткод: | B051 2151 |
| Деталь: | OPC Belt Waste Toner Bottle |
| Парткод: | G070 2100 |
| Деталь: | Transfer Belt Waste Toner Bottle |
| Парткод: | G070 6310 |
| Деталь: | Flanged Hexagonal Head Bolt -M4x14 |
| Парткод: | G070 2358 |
| Деталь: | PCU Drive Joint |
| Парткод: | G070 2318 |
| Деталь: | Wire Cleaning Motor |
| Парткод: | G070 2176 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 0087 |
| Деталь: | Spacer - 4x6x1 |
| Парткод: | A096 3863 |
| Деталь: | Corona Wire:Charge Corona |
| Парткод: | G070 2110 |
| Деталь: | Corona Wire Spring |
| Парткод: | 54 422 108 |
| Деталь: | Positioning Pin |
| Парткод: | A172 7611 |
| Деталь: | Charge Corona Grid |
| Парткод: | G070 2156 |
| Деталь: | Charge Corona Cleaner Holder |
| Парткод: | G070 2167 |
| Деталь: | FRONT POSITIONING PLATE |
| Парткод: | G070 2119 |
| Деталь: | Raer Positioning Plate |
| Парткод: | G070 2120 |
| Деталь: | Grip Belt - PCU |
| Парткод: | G070 2344 |
| Деталь: | Doble Gear - 15Z/23Z |
| Парткод: | AB01 7595 |
| Деталь: | Rear Bracket - ITB Cleaning Unit |
| Парткод: | G070 6394 |
| Деталь: | Idler Gear - 20Z |
| Парткод: | AB01 4215 |
| Деталь: | Idler Gear - 19Z |
| Парткод: | AB01 4224 |
| Деталь: | Gear - 26Z |
| Парткод: | AB01 7631 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 1475 |
| Деталь: | Knob Screw - Charge Corona |
| Парткод: | G070 2174 |
| Деталь: | Grid Shadeing Plate |
| Парткод: | G070 2136 |
| Деталь: | Front End Block Cover |
| Парткод: | G070 2159 |
| Деталь: | Rear End Block Cover |
| Парткод: | G070 2160 |
| Деталь: | Rear Bracket - Grid Plate |
| Парткод: | G070 2161 |
| Деталь: | Spring Plate - Gridtension |
| Парткод: | G070 2162 |
| Деталь: | Spring Plate - Screw Shaft |
| Парткод: | G070 2163 |
| Деталь: | Cleaner Slider - Charge Corona |
| Парткод: | G070 2166 |
| Деталь: | Charge Corona Cleaner |
| Парткод: | G070 2168 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1472 |
| Деталь: | Gear - 13Z |
| Парткод: | AB01 1473 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 1474 |
| Деталь: | Idler Gear - 35Z |
| Парткод: | AB01 1476 |
| Деталь: | Cleaner Screw Shaft |
| Парткод: | G070 2165 |
| Деталь: | Slider Ring |
| Парткод: | A172 7650 |
| Деталь: | Belt Cleaning Assembly |
| Парткод: | G070 6300 |
| Деталь: | Charge Section Assembly |
| Парткод: | G070 2050 |
| Деталь: | Spacer - End Block |
| Парткод: | G070 2164 |
| Деталь: | Cap - 20mm |
| Парткод: | A257 3490 |
| Деталь: | Left Cover Hinge |
| Парткод: | G070 1075 |
| Деталь: | Grip Bracket - Left |
| Парткод: | G070 1109 |
| Деталь: | GRIP |
| Парткод: | G070 1107 |
| Деталь: | Left Bracket - Door Switch |
| Парткод: | G070 5571 |
| Деталь: | Left Link - Safety Switch |
| Парткод: | G070 5569 |
| Деталь: | Left Tension Spring |
| Парткод: | G070 5567 |
| Деталь: | Left Shoe |
| Парткод: | G070 2624 |
| Деталь: | Slide Switch Cover |
| Парткод: | G070 5556 |
| Деталь: | Switch Bracket - Power Source |
| Парткод: | G070 5558 |
| Деталь: | Small Link - Power Source |
| Парткод: | G070 5559 |
| Деталь: | Switch Link - Power Source |
| Парткод: | G070 5557 |
| Деталь: | PCU Lower Rail |
| Парткод: | G070 2372 |
| Деталь: | Upper Support Stay |
| Парткод: | G070 2370 |
| Деталь: | PCU Upper Rail |
| Парткод: | G070 2371 |
| Деталь: | DENSITY SENSOR |
| Парткод: | AW01 0097 |
| Деталь: | Fusing Unit Rail |
| Парткод: | G070 4302 |
| Деталь: | Fusing Unit Rail |
| Парткод: | G070 4300 |
| Деталь: | Charge Ground Plate |
| Парткод: | G070 2135 |
| Деталь: | On/off Rail |
| Парткод: | G070 6405 |
| Деталь: | Grounding Plate - Belt Cleaning |
| Парткод: | G070 6406 |
| Деталь: | Grounding Plate Bracket |
| Парткод: | G070 6227 |
| Деталь: | Hook Bracket |
| Парткод: | G070 4828 |
| Деталь: | Right Cover Hook |
| Парткод: | G070 1180 |
| Деталь: | Right Rail |
| Парткод: | G070 2620 |
| Деталь: | Grip Bracket - Front Right |
| Парткод: | B051 1132 |
| Деталь: | Right Grip |
| Парткод: | G070 1108 |
| Деталь: | COVER HINGE |
| Парткод: | G070 1074 |
| Деталь: | Front Lower Guide |
| Парткод: | G070 2335 |
| Деталь: | PCU Rail Seal - 3x30x5 |
| Парткод: | G070 1104 |
| Деталь: | PCU Rail Seal - 9x19x5 |
| Парткод: | G070 1105 |
| Деталь: | Right Rail Shoe |
| Парткод: | G070 2622 |
| Деталь: | Lower Shield - PCU Rail |
| Парткод: | G070 1092 |
| Деталь: | Paper Tray Assy |
| Парткод: | G070 2700 |
| Деталь: | Front Side Fence |
| Парткод: | G070 2712 |
| Деталь: | END FENCE |
| Парткод: | AF01 7025 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | AF01 1047 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52 152 713 |
| Деталь: | Spring - 5.9n/16.6n |
| Парткод: | AA06 3628 |
| Деталь: | Rear Side Fence |
| Парткод: | G070 2716 |
| Деталь: | Joint - Feed Roller Shaft |
| Парткод: | G070 2728 |
| Деталь: | SPRING |
| Парткод: | AA06 3630 |
| Деталь: | Bushing - 8x12x10 |
| Парткод: | B039 2727 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G070 2725 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Base Stopper |
| Парткод: | G070 2711 |
| Деталь: | Ground Plate- Bottom Plate |
| Парткод: | G070 2719 |
| Деталь: | Gear - 16Z |
| Парткод: | A267 2869 |
| Деталь: | PAPER FEED ROLLER SHAFT |
| Парткод: | G070 2726 |
| Деталь: | Friction pad |
| Парткод: | G070 2722 |
| Деталь: | Spring - 2.8n |
| Парткод: | AA06 3629 |
| Деталь: | Paper Feed Roller - 36mm |
| Парткод: | AF03 1059 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Paper Size Sensor Link |
| Парткод: | G070 2710 |
| Деталь: | Decal - Paper Set Direction |
| Парткод: | G070 2730 |
| Деталь: | Decal - OHP Paper Feed |
| Парткод: | B051 2580 |
| Деталь: | Decal - End Fence |
| Парткод: | B051 2581 |
| Деталь: | Front Lever - Stopper |
| Парткод: | G070 2714 |
| Деталь: | Spring Plate Stopper |
| Парткод: | G070 2713 |
| Деталь: | Front Side Fence |
| Парткод: | AF01 6097 |
| Деталь: | Rear Lever Stopper |
| Парткод: | G070 2717 |
| Деталь: | Rear Side Fence |
| Парткод: | AF01 6098 |
| Деталь: | SCREW |
| Парткод: | AA14 3493 |
| Деталь: | Right Link - Transport Cover |
| Парткод: | G070 1196 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | G070 2607 |
| Деталь: | Leading Edghe Guide |
| Парткод: | G070 2608 |
| Деталь: | Front Support Plate - Right Cover |
| Парткод: | G070 1354 |
| Деталь: | RIGHT COVER |
| Парткод: | G070 1357 |
| Деталь: | Rear Support Plate - Right Cover |
| Парткод: | G070 1356 |
| Деталь: | Rear Right Cover Hook |
| Парткод: | G070 1353 |
| Деталь: | SPRING |
| Парткод: | AA06 3402 |
| Деталь: | SPRING HOLDER |
| Парткод: | A232 1284 |
| Деталь: | Un Lock Hook |
| Парткод: | G070 1361 |
| Деталь: | GUIDE PLATE |
| Парткод: | G070 2606 |
| Деталь: | Connector Holder |
| Парткод: | G070 2118 |
| Деталь: | Discharge Harness |
| Парткод: | G070 5307 |
| Деталь: | Terminal Holder |
| Парткод: | G070 2126 |
| Деталь: | Charge Spring |
| Парткод: | G070 2138 |
| Деталь: | Charge Corona Terminal |
| Парткод: | G070 2124 |
| Деталь: | PCU Grounding Plate |
| Парткод: | G070 2336 |
| Деталь: | Positioning Sensor - Transfer Belt |
| Парткод: | AW01 0096 |
| Деталь: | Bracket - Positioning Sensor |
| Парткод: | B051 6160 |
| Деталь: | Feeler |
| Парткод: | G070 2096 |
| Деталь: | Waste Toner Bottle Bracket |
| Парткод: | G070 2107 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Bracket - Waste Toner Sensor |
| Парткод: | G070 6407 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Paper End Sensor Feeler |
| Парткод: | G070 2646 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Release Lever |
| Парткод: | G070 2645 |
| Деталь: | Feeler - Paper Bolume Sensor |
| Парткод: | G070 2647 |
| Деталь: | Paper End Sensor Bracket |
| Парткод: | G070 2642 |
| Деталь: | Sensor Rear Bracket |
| Парткод: | G070 2644 |
| Деталь: | Paper Feed Harness |
| Парткод: | G070 5309 |
| Деталь: | Power Pack - BCTCLD C1B |
| Парткод: | AZ32 0117 |
| Деталь: | Sensor Front Bracket |
| Парткод: | G070 2643 |
| Деталь: | Feeler Holder - Vertical Transport |
| Парткод: | G070 2637 |
| Деталь: | Vertical Transport Feeler |
| Парткод: | G070 2638 |
| Деталь: | SPRING |
| Парткод: | AA06 6633 |
| Деталь: | Terminal Holder |
| Парткод: | G070 6166 |
| Деталь: | TERMINAL |
| Парткод: | G070 6165 |
| Деталь: | Support Plate - Front Right |
| Парткод: | G070 1087 |
| Деталь: | High Voltage Harness -Dischage Pin |
| Парткод: | G070 5369 |
| Деталь: | High Boltage Harness - T2 |
| Парткод: | G070 5351 |
| Деталь: | High Voltage Harness |
| Парткод: | G070 5368 |
| Деталь: | Harness - Bcu-ppi |
| Парткод: | G070 5302 |
| Деталь: | Poshitioning Sensor Plate |
| Парткод: | G070 6161 |
| Деталь: | Charge Corona Terminal Assy |
| Парткод: | G070 2131 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0014 |
| Деталь: | LEFT INNER COVER |
| Парткод: | G070 1370 |
| Деталь: | Development Inner Cover |
| Парткод: | G070 1375 |
| Деталь: | Operation panel Assembry (LT) |
| Парткод: | G070 5620 |
| Деталь: | Operation panel Assembry (A4) |
| Парткод: | G070 5630 |
| Деталь: | Exit cover |
| Парткод: | G070 1330 |
| Деталь: | Exit Right Cover |
| Парткод: | G070 1335 |
| Деталь: | REAR RIGHT COVER |
| Парткод: | G070 1265 |
| Деталь: | Duplex Small Cap |
| Парткод: | G070 1262 |
| Деталь: | Duplex Cap |
| Парткод: | G070 1261 |
| Деталь: | Front right cover |
| Парткод: | G070 1260 |
| Деталь: | Corona Wire Spring |
| Парткод: | 54 422 108 |
| Деталь: | Inner Cover - Lower Right |
| Парткод: | G070 1380 |
| Деталь: | Front door |
| Парткод: | G070 1250 |
| Деталь: | Hinge pin |
| Парткод: | A166 1363 |
| Деталь: | Operation Sheet |
| Парткод: | G070 1397 |
| Деталь: | PCU Upper Decal |
| Парткод: | G070 2373 |
| Деталь: | Magnet Catich - Front Cover |
| Парткод: | G070 1253 |
| Деталь: | Decal - Emblem (LAN) |
| Парткод: | G071 1385 |
| Деталь: | Decal - Emblem (INF) |
| Парткод: | G071 1386 |
| Деталь: | Decal - Emblem (GES) |
| Парткод: | G071 1387 |
| Деталь: | Decal - Emblem (REX) |
| Парткод: | G071 1388 |
| Деталь: | Decal - Emblem (NSA) |
| Парткод: | G071 1389 |
| Деталь: | Decal - Emblem (RIC NA) |
| Парткод: | G071 1396 |
| Деталь: | Decal - Emblem (RIC EU) |
| Парткод: | G071 1397 |
| Деталь: | Wire - Operation Panel |
| Парткод: | G070 5367 |
| Деталь: | Rubber Foot - 23mm |
| Парткод: | GH01 0005 |
| Деталь: | Decal - Inkjet Paper Caution |
| Парткод: | GA00 3038 |
| Деталь: | Decal - Machine Guide |
| Парткод: | G070 2374 |
| Деталь: | Feeler - Paper Overflow |
| Парткод: | A267 4478 |
| Деталь: | Overflow Shaft |
| Парткод: | G070 4472 |
| Деталь: | Discharge Brush |
| Парткод: | AA12 0103 |
| Деталь: | Transport Exit Roller |
| Парткод: | AF02 0545 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Feeler - Paper Feed Sensor |
| Парткод: | A267 4476 |
| Деталь: | Exit Guide Plate |
| Парткод: | G070 4455 |
| Деталь: | Edit Grounding Plate |
| Парткод: | G070 4458 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1229 |
| Деталь: | Gear - 27Z |
| Парткод: | AB01 1425 |
| Деталь: | Exit Angle |
| Парткод: | G070 4495 |
| Деталь: | Exit Drive Bracket |
| Парткод: | G070 4920 |
| Деталь: | 4 Bin Rrar Bracket |
| Парткод: | G070 4491 |
| Деталь: | Spring Plate - Outer Tension Roller |
| Парткод: | G070 4466 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Roller - 9mm |
| Парткод: | G070 4459 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2112 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | G070 4461 |
| Деталь: | Idle Roller |
| Парткод: | G047 4785 |
| Деталь: | 4 Bin Front Bracket |
| Парткод: | G070 4490 |
| Деталь: | Fusing Exit Roller |
| Парткод: | AF02 0546 |
| Деталь: | Guide Plate - Fusing Exit |
| Парткод: | G070 4481 |
| Деталь: | Right Upper Stay |
| Парткод: | G070 1060 |
| Деталь: | Gear - 14Z |
| Парткод: | AB01 1230 |
| Деталь: | Discharge Brush |
| Парткод: | AA12 0113 |
| Деталь: | Grounding Plate - Fusing Exit |
| Парткод: | G070 4492 |
| Деталь: | Bracket - Fusing Exit Feeler |
| Парткод: | G070 4477 |
| Деталь: | Sensor Bracket - Fusing Exit |
| Парткод: | G070 4486 |
| Деталь: | Photointerruptor - EE-SX4235A-P1 |
| Парткод: | AW02 0056 |
| Деталь: | Connecting Harness - Fusing Exit |
| Парткод: | G070 5303 |
| Деталь: | Fusing Exit Feeler |
| Парткод: | G070 4476 |
| Деталь: | Decal Warning (High Temperature) |
| Парткод: | AA00 0301 |
| Деталь: | Spring - Fusing Exit Feeler |
| Парткод: | G070 4478 |
| Деталь: | Seal - Exit |
| Парткод: | G070 4496 |
| Деталь: | Clip - Discharge Brush |
| Парткод: | G070 4462 |
| Деталь: | Terminal Cover - Doctor Blade |
| Парткод: | G070 3293 |
| Деталь: | Doctor Blade Terminal |
| Парткод: | G070 3291 |
| Деталь: | Rear Toner End Sensor |
| Парткод: | G070 5270 |
| Деталь: | Doctor Blade Terminal |
| Парткод: | G070 3292 |
| Деталь: | Rear Side Plate |
| Парткод: | G070 3232 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | G070 3239 |
| Деталь: | Harness - ID Sensor Board |
| Парткод: | G070 5285 |
| Деталь: | ID Sensor Board |
| Парткод: | G070 5281 |
| Деталь: | Bias Terminal Cover |
| Парткод: | G070 3295 |
| Деталь: | Development Shaft - FC |
| Парткод: | G070 4607 |
| Деталь: | Development Vias Terminal |
| Парткод: | G070 3236 |
| Деталь: | High Boltage Harness - B2 |
| Парткод: | G070 5353 |
| Деталь: | Left Upper Stay |
| Парткод: | G070 1059 |
| Деталь: | Side Plate - Front Left |
| Парткод: | G070 3233 |
| Деталь: | Display Decal - Magenta |
| Парткод: | G024 6992 |
| Деталь: | Display Decal - Cyan |
| Парткод: | G024 6991 |
| Деталь: | Display Decal - Yellow |
| Парткод: | G024 6993 |
| Деталь: | Display Decal - Black |
| Парткод: | G024 6994 |
| Деталь: | Spring Cap |
| Парткод: | G070 3240 |
| Деталь: | Development Unit - Y Assy |
| Парткод: | G070 3502 |
| Деталь: | Development Unit - C Assy |
| Парткод: | G070 3503 |
| Деталь: | Development Unit - M Assy |
| Парткод: | G070 3501 |
| Деталь: | Doctor Blade Bias Harness |
| Парткод: | G070 5363 |
| Деталь: | Harness - BCU-ID |
| Парткод: | G070 5364 |
| Деталь: | Front Toner End Sensor |
| Парткод: | G070 5260 |
| Деталь: | Damper - Development Roller |
| Парткод: | G070 3248 |
| Деталь: | Damper Cover |
| Парткод: | G070 3237 |
| Деталь: | Frontside Plate |
| Парткод: | G070 3231 |
| Деталь: | Color Shaft - Development |
| Парткод: | G070 4605 |
| Деталь: | Lower Shield - Front Left |
| Парткод: | G070 1094 |
| Деталь: | Front Lower Middle Shield |
| Парткод: | G070 1093 |
| Деталь: | Slide Rail |
| Парткод: | G070 6145 |
| Деталь: | Grounding Plate - Slide Rail |
| Парткод: | G070 6175 |
| Деталь: | Slide Rail Stopper |
| Парткод: | G070 6157 |
| Деталь: | Left Lower Rail |
| Парткод: | G070 6150 |
| Деталь: | Power Supply Unit Cover |
| Парткод: | G070 6158 |
| Деталь: | Right Lower Rail |
| Парткод: | G070 6152 |
| Деталь: | Gear - 32Z |
| Парткод: | AB01 1421 |
| Деталь: | Gap Gear Guide |
| Парткод: | G070 1197 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gear - 28Z |
| Парткод: | AB01 1225 |
| Деталь: | Drive Roller - Vertical Transport |
| Парткод: | AF02 0537 |
| Деталь: | Registration Drive Roller |
| Парткод: | AF02 0536 |
| Деталь: | BUSHING |
| Парткод: | AA08 0271 |
| Деталь: | Registration Sensor Harness |
| Парткод: | G070 5310 |
| Деталь: | Photo Reflection Sensor |
| Парткод: | AW01 0049 |
| Деталь: | Registration Sensor Bracket |
| Парткод: | G070 2577 |
| Деталь: | Knob Screw - M4 |
| Парткод: | G070 6174 |
| Деталь: | Registration Guide |
| Парткод: | G070 2573 |
| Деталь: | Stopper Bracket |
| Парткод: | G070 6170 |
| Деталь: | Screw - M3 |
| Парткод: | G070 6173 |
| Деталь: | Drive Case - Assembly |
| Парткод: | G070 4700 |
| Деталь: | Brushless Motor - DC8.8W 9Z |
| Парткод: | AX06 0224 |
| Деталь: | Harness - IOB-OPC |
| Парткод: | G070 5317 |
| Деталь: | Fly Wheel - 140mm |
| Парткод: | G070 4732 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0868 |
| Деталь: | Magnetic clutch |
| Парткод: | AX21 0078 |
| Деталь: | Magnetic clutch |
| Парткод: | AX21 0079 |
| Деталь: | Harness - IOB-Transport M |
| Парткод: | G070 5304 |
| Деталь: | Brushless Motor - DC26W 9Z |
| Парткод: | AX06 0230 |
| Деталь: | Development Drive Bracket |
| Парткод: | G070 4611 |
| Деталь: | Gear - 93Z/42Z |
| Парткод: | AB01 7565 |
| Деталь: | Idler Gear - 67Z |
| Парткод: | AB01 0353 |
| Деталь: | Harness Guide |
| Парткод: | G070 5543 |
| Деталь: | Spring Plate - Brushless Motor |
| Парткод: | G070 4731 |
| Деталь: | Rear Arm |
| Парткод: | G070 6239 |
| Деталь: | Separation Bias Wire |
| Парткод: | G070 5356 |
| Деталь: | Transport Guide W/t Discharge Pins |
| Парткод: | G070 6231 |
| Деталь: | Transfer Unit Frame |
| Парткод: | G070 6204 |
| Деталь: | Arm Shaft |
| Парткод: | G070 6240 |
| Деталь: | Frame Stay |
| Парткод: | G070 6205 |
| Деталь: | Rear Grounding Plate |
| Парткод: | G070 6210 |
| Деталь: | Terminal Cover Sheet |
| Парткод: | G070 6243 |
| Деталь: | Transfer Roller Terminal |
| Парткод: | G070 6218 |
| Деталь: | Front Arm |
| Парткод: | G070 6238 |
| Деталь: | Separation Terminal |
| Парткод: | G070 6220 |
| Деталь: | Transfer Unit Spring -10n |
| Парткод: | AA06 3876 |
| Деталь: | Vertical Transport Sheet |
| Парткод: | G070 6229 |
| Деталь: | Right Cover Guide - By-pass Feed |
| Парткод: | G070 1281 |
| Деталь: | Transfer Roller Bushing |
| Парткод: | G070 6202 |
| Деталь: | Transfer Roller Holder |
| Парткод: | G070 6206 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | G070 6200 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | G070 6201 |
| Деталь: | Collar - 8x11x10 |
| Парткод: | G070 6236 |
| Деталь: | Entrance Guide |
| Парткод: | G070 6245 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G070 2584 |
| Деталь: | Right Guide Plate |
| Парткод: | G070 2583 |
| Деталь: | Registration Driven Roller - 14mm |
| Парткод: | AF02 1068 |
| Деталь: | BUSHING |
| Парткод: | AA08 0259 |
| Деталь: | Spring - 20n |
| Парткод: | AA06 3631 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | A232 2862 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | SPRING |
| Парткод: | AA06 3563 |
| Деталь: | Transfer Unit Stopper |
| Парткод: | G070 6221 |
| Деталь: | Right Cover - Vertical Transport |
| Парткод: | G070 1359 |
| Деталь: | Ground Wire - 2nd Transfer Arm |
| Парткод: | G070 5370 |
| Деталь: | Registration Driven Cleaner |
| Парткод: | G070 2585 |
| Деталь: | Temperature/humidity Sensor |
| Парткод: | AW14 0010 |
| Деталь: | Sensor bracket |
| Парткод: | G070 5542 |
| Деталь: | Fan Motor - DC2.4W |
| Парткод: | AX64 0103 |
| Деталь: | Fan Motor - 60x25mm |
| Парткод: | AX64 0134 |
| Деталь: | Connector bracket |
| Парткод: | G070 5541 |
| Деталь: | Upper Charge Duct |
| Парткод: | G070 1085 |
| Деталь: | Lower Charge Duct |
| Парткод: | G070 1086 |
| Деталь: | Duct Shield |
| Парткод: | G070 1083 |
| Деталь: | Application Middle Bracket |
| Парткод: | G070 5523 |
| Деталь: | ROM-DIMM PCB-PS/PCL |
| Парткод: | G070 5851 |
| Деталь: | Application Right Middle Bracket |
| Парткод: | G070 5526 |
| Деталь: | Card cover |
| Парткод: | G070 5527 |
| Деталь: | Stud - M3x40x6 |
| Парткод: | G070 5529 |
| Деталь: | Print Control Board |
| Парткод: | G070 5844 |
| Деталь: | Application Rear Rack |
| Парткод: | G070 5486 |
| Деталь: | Front Rack |
| Парткод: | G070 5469 |
| Деталь: | Fan Motor - 60x15mm |
| Парткод: | AX64 0133 |
| Деталь: | Philips Screw - M3 |
| Парткод: | C218 3051 |
| Деталь: | By-pass Feed Unit Harness |
| Парткод: | G070 5330 |
| Деталь: | Gate Relay Harness |
| Парткод: | G070 5337 |
| Деталь: | Lower Duct Seal |
| Парткод: | G070 1100 |
| Деталь: | Upper Duct Seal - 90x10x4 |
| Парткод: | G070 1101 |
| Деталь: | Middle Duct Seal - 10x70x4 |
| Парткод: | G070 1102 |
| Деталь: | Latch Duct Seal - 12x20 |
| Парткод: | G070 1103 |
| Деталь: | Knob Screw |
| Парткод: | AA14 9731 |
| Деталь: | TOTAL COUNTER |
| Парткод: | G070 9099 |
| Деталь: | USB Board |
| Парткод: | B525 5660 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Separation Roller - Manual Feed |
| Парткод: | AF03 2046 |
| Деталь: | Torque Limiter - 40mnm 18mm |
| Парткод: | G060 2900 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Separator Guide Plate |
| Парткод: | G304 6808 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3016 |
| Деталь: | Drive Roller - By-pass Feed |
| Парткод: | AF02 0543 |
| Деталь: | DC Solenoid - Pick-up |
| Парткод: | G060 2937 |
| Деталь: | Transmission Drive Bracket |
| Парткод: | G304 6832 |
| Деталь: | Tightener Arm |
| Парткод: | G304 6829 |
| Деталь: | Idler Gear - 25z |
| Парткод: | AB01 1223 |
| Деталь: | SPRING |
| Парткод: | AA06 0872 |
| Деталь: | Gear - 28Z |
| Парткод: | AB01 1224 |
| Деталь: | Separation Drive Gear - 22Z |
| Парткод: | AB01 1222 |
| Деталь: | Magnetic Clutch - 245mnm 35Z |
| Парткод: | AX20 0230 |
| Деталь: | Feed Shaft |
| Парткод: | AA14 0742 |
| Деталь: | pickup roller |
| Парткод: | AF03 0022 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 1387 |
| Деталь: | LOWER COVER |
| Парткод: | G304 6867 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1416 |
| Деталь: | Drive Shaft |
| Парткод: | AA14 0741 |
| Деталь: | Driven Shaft |
| Парткод: | G304 6810 |
| Деталь: | Photointerruptor - EE-SX4235A-P1 |
| Парткод: | AW02 0056 |
| Деталь: | Feeler - Paper End |
| Парткод: | G060 2931 |
| Деталь: | Guide Plate - Drive Gear |
| Парткод: | G304 6828 |
| Деталь: | Roller Clutch - 6x14x10 |
| Парткод: | AA08 3018 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3499 |
| Деталь: | Stopper Plate |
| Парткод: | G060 2914 |
| Деталь: | Grouding Wire Harness |
| Парткод: | G304 5332 |
| Деталь: | FEED ROLLER |
| Парткод: | G047 3257 |
| Деталь: | By-pass Feed Housing |
| Парткод: | G304 6804 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 0409 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | SPRING |
| Парткод: | AA06 3401 |
| Деталь: | Gear - Separation Driven |
| Парткод: | AB01 1417 |
| Деталь: | Pick-up Arm - Manual Feed |
| Парткод: | G060 2932 |
| Деталь: | Feeler Roller |
| Парткод: | A134 2661 |
| Деталь: | By-pass Feed Unit Harness |
| Парткод: | G304 5331 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3568 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | A232 2862 |
| Деталь: | LEFT COVER |
| Парткод: | G070 1271 |
| Деталь: | Left Cover Hook |
| Парткод: | G070 1291 |
| Деталь: | Bushing - Left Cover Hook |
| Парткод: | G070 1293 |
| Деталь: | Development Unit Cover |
| Парткод: | G070 1290 |
| Деталь: | REAR COVER |
| Парткод: | G070 1340 |
| Деталь: | Exhaust Filter Dust Filter |
| Парткод: | A259 2337 |
| Деталь: | Rear Filter Cover |
| Парткод: | G070 1069 |
| Деталь: | Sound Proofing - Cover Filter |
| Парткод: | G070 1077 |
| Деталь: | FILTER COVER |
| Парткод: | G070 1084 |
| Деталь: | OZONE FILTER |
| Парткод: | AA01 0113 |
| Деталь: | Exhaust filter |
| Парткод: | AA01 2120 |
| Деталь: | Upper Exit Cover |
| Парткод: | G070 1320 |
| Деталь: | Paper exit Cover |
| Парткод: | G070 1312 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0014 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Upper Case - Safety Switch |
| Парткод: | G070 5562 |
| Деталь: | Right Tension Spring |
| Парткод: | G070 5565 |
| Деталь: | Right Link - Safety Switch |
| Парткод: | G070 5568 |
| Деталь: | Link Middle Lever |
| Парткод: | G070 5563 |
| Деталь: | Right Tension Spring |
| Парткод: | G070 5566 |
| Деталь: | Lower Case - Safety Switch |
| Парткод: | G070 5561 |
| Деталь: | Link Outer Lever |
| Парткод: | G070 5564 |
| Деталь: | Link Middle Lever - Left |
| Парткод: | G070 5570 |
| Деталь: | Rear Link Lever |
| Парткод: | G070 5573 |
| Деталь: | Link Lever - Rear Right |
| Парткод: | G070 5574 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | G070 5575 |
| Деталь: | Knob Screw - M4x10 |
| Парткод: | A217 1340 |
| Деталь: | Harness - LDB-LD5V |
| Парткод: | G070 5320 |
| Деталь: | Harness - IOB 24V |
| Парткод: | G070 5315 |
| Деталь: | Vertical Filter Cover Seal - 7x60 |
| Парткод: | G070 1096 |
| Деталь: | Rear Filter Cover Seal-7x16x2 |
| Парткод: | G070 1097 |
| Деталь: | Front Filter Cover Seal-5x105x2 |
| Парткод: | G070 1098 |
| Деталь: | Middle Filter Cover Seal-5x53x3 |
| Парткод: | G070 1099 |
| Деталь: | Cushion - Safety Switch |
| Парткод: | G070 5576 |
| Деталь: | Film - Paper Feed Sensor |
| Парткод: | G070 1322 |
| Деталь: | Tray Heater Kit - 120V 9W1W |
| Парткод: | G070 9502 |
| Деталь: | Tray Heater Kit - 230V 9W1W |
| Парткод: | G070 9503 |
| Деталь: | Pick-off Pawl - Pressure Roller |
| Парткод: | G070 4004 |
| Деталь: | Knob Screw - M4 |
| Парткод: | AA14 3524 |
| Деталь: | Grip Decal |
| Парткод: | AA00 3016 |
| Деталь: | Thermofuse - 131C |
| Парткод: | G060 4351 |
| Деталь: | Decal - Warning |
| Парткод: | GA00 0025 |
| Деталь: | Stripper Pawl - Pressure Roller |
| Парткод: | AE04 4041 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Grip Decal |
| Парткод: | AA00 3013 |
| Деталь: | Shaft Support Plate |
| Парткод: | G070 4148 |
| Деталь: | Fusing Upper Cover |
| Парткод: | G070 4150 |
| Деталь: | Guide Plate - Fusing Exit |
| Парткод: | G070 4106 |
| Деталь: | Fusing Belt Upper Stay |
| Парткод: | G070 4221 |
| Деталь: | Stripper Pawl Spring |
| Парткод: | AA06 9261 |
| Деталь: | Front Electrode Plate |
| Парткод: | G070 4132 |
| Деталь: | Rearelectrode Plate |
| Парткод: | G070 4135 |
| Деталь: | Connecting Electrode Plate |
| Парткод: | G070 4141 |
| Деталь: | Fusing AC Harness - 120V |
| Парткод: | G070 5332 |
| Деталь: | Fusing AC Harness - 230V |
| Парткод: | G070 5361 |
| Деталь: | Rear Pressure Terminal Electrode |
| Парткод: | G070 4143 |
| Деталь: | Fusing Lower Cover |
| Парткод: | G070 4130 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Front Oil Absorber Felt |
| Парткод: | G070 4138 |
| Деталь: | Spring Plate - Front Fusing Cover |
| Парткод: | G070 4136 |
| Деталь: | Spring Plate - Rear Fusing Cover |
| Парткод: | G070 4137 |
| Деталь: | Transfer/separation Receptacle |
| Парткод: | G070 6223 |
| Деталь: | Magnetic Clutch - 0.4nm 46z |
| Парткод: | AX20 0224 |
| Деталь: | Timing Belt - 120TS2M |
| Парткод: | AA04 3567 |
| Деталь: | Gear - 33Z/30T |
| Парткод: | AB01 7561 |
| Деталь: | Paper Feed Tightener |
| Парткод: | G070 4908 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0869 |
| Деталь: | Gear - 40Z/42Z |
| Парткод: | AB01 7560 |
| Деталь: | GRIP |
| Парткод: | G070 1107 |
| Деталь: | Feed Drive Shaft |
| Парткод: | G070 4907 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Magnetic Clutch Bracket |
| Парткод: | G070 4906 |
| Деталь: | Right Grip |
| Парткод: | G070 1108 |
| Деталь: | Grip Bracket - Rear Light |
| Парткод: | G070 1110 |
| Деталь: | Stepper Motor - DC4.42W |
| Парткод: | G568 2702 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | AA16 1153 |
| Деталь: | Drive Bracket - Paper Feed |
| Парткод: | G070 4903 |
| Деталь: | Gear - 58Z/37Z |
| Парткод: | AB01 7563 |
| Деталь: | Gear - 32Z/33T |
| Парткод: | AB01 7562 |
| Деталь: | Timing Belt - 480TS3M |
| Парткод: | AA04 3568 |
| Деталь: | Grip Bracket - Left |
| Парткод: | G070 1109 |
| Деталь: | High Boltage Harness - T2 |
| Парткод: | G070 5351 |
| Деталь: | Transport Bracket Assembly |
| Парткод: | G070 4800 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0881 |
| Деталь: | Brushless Motor - DC26W 10Z |
| Парткод: | AX06 0225 |
| Деталь: | Harness - IOB-Transport M |
| Парткод: | G070 5304 |
| Деталь: | FAN DUCT |
| Парткод: | G070 1070 |
| Деталь: | Timing Belt - 117TS2M |
| Парткод: | AA04 3566 |
| Деталь: | Timing Pulley - 24Z/34T |
| Парткод: | AB01 7555 |
| Деталь: | Tightener Assembly |
| Парткод: | G070 4741 |
| Деталь: | Paper Size Sensor Bracket |
| Парткод: | G070 2631 |
| Деталь: | Holder - Paper Tray |
| Парткод: | G060 2801 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0024 |
| Деталь: | Shielding Plate |
| Парткод: | G070 5502 |
| Деталь: | Gear - 98Z/20T |
| Парткод: | AB01 7554 |
| Деталь: | Spring Clutch - 27Z |
| Парткод: | AB04 0018 |
| Деталь: | Swivel Bracket |
| Парткод: | G070 4810 |
| Деталь: | Gear - 25Z/36Z |
| Парткод: | G070 4851 |
| Деталь: | DC Solenoid - Transfer Roller |
| Парткод: | G070 4821 |
| Деталь: | Second Drive Shaft |
| Парткод: | AA14 5544 |
| Деталь: | Gear - 33Z |
| Парткод: | AB01 4210 |
| Деталь: | Gear - 30Z |
| Парткод: | AB01 4209 |
| Деталь: | Gear - 33Z/27Z |
| Парткод: | G070 4850 |
| Деталь: | Arm bracket |
| Парткод: | G070 4825 |
| Деталь: | On/Off Cam - Second Brake |
| Парткод: | G070 4829 |
| Деталь: | Magnetic Clutch - 32Z |
| Парткод: | AX20 0236 |
| Деталь: | Cleaning Drive Shaft |
| Парткод: | AA14 5547 |
| Деталь: | Grar - 65z/20z |
| Парткод: | AB01 7557 |
| Деталь: | Cleaning On/Off Shaft |
| Парткод: | AA14 5546 |
| Деталь: | Gear - 24Z/53Z |
| Парткод: | AB01 7556 |
| Деталь: | Gear - 49Z |
| Парткод: | AB01 4208 |
| Деталь: | DC Solenoid - Belt Cleaning |
| Парткод: | G070 4820 |
| Деталь: | Cleaning On/off Cam |
| Парткод: | G070 4818 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3647 |
| Деталь: | SPRING SPACER |
| Парткод: | G070 4823 |
| Деталь: | Gear - 18Z |
| Парткод: | AB01 1437 |
| Деталь: | Second Shaft - On/Off |
| Парткод: | G070 4832 |
| Деталь: | Cam Roller |
| Парткод: | G070 4834 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Fusing Inner Bracket |
| Парткод: | G070 4806 |
| Деталь: | Transport Bracket |
| Парткод: | G070 4801 |
| Деталь: | Paper Size Sensor Harness |
| Парткод: | G070 5366 |
| Деталь: | Front Cover - By-pass Feed |
| Парткод: | G304 6859 |
| Деталь: | Hinge Lock |
| Парткод: | G304 6868 |
| Деталь: | Hexagonal Set Screw - M3x8 |
| Парткод: | G304 6811 |
| Деталь: | Upper Cover - By-pass Feed |
| Парткод: | G304 6848 |
| Деталь: | Rear Cover - By-pass Feed |
| Парткод: | G304 6847 |
| Деталь: | Front Side Fence |
| Парткод: | G304 6841 |
| Деталь: | Rear Side Fence |
| Парткод: | G304 6842 |
| Деталь: | Decal - By-pass Feed Direction |
| Парткод: | G304 6813 |
| Деталь: | Paper Guide - Manual Feed Tabl |
| Парткод: | G060 2905 |
| Деталь: | MANUAL FEED TABLE |
| Парткод: | G304 6839 |
| Деталь: | By-pass Feed Table Cover |
| Парткод: | G304 6840 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G012 3050 |
| Деталь: | Decal - OHP Paper Feed |
| Парткод: | B051 2580 |
| Деталь: | COVER |
| Парткод: | G070 1941 |
| Деталь: | Front Cover Shield |
| Парткод: | G070 1942 |
| Деталь: | Decal - LD 655 |
| Парткод: | AA00 0217 |
| Деталь: | LD Unit Cover |
| Парткод: | G070 1971 |
| Деталь: | Cover Bracket - LD Unit |
| Парткод: | G070 1972 |
| Деталь: | Imaging Unit |
| Парткод: | G070 1855 |
| Деталь: | Shield Glass Cover |
| Парткод: | G070 1952 |
| Деталь: | Cleaner Holder |
| Парткод: | G070 1954 |
| Деталь: | Polygon Scanner |
| Парткод: | G070 1975 |
| Деталь: | Polygon Motor Harness |
| Парткод: | G070 5322 |
| Деталь: | Cylindrical Lens |
| Парткод: | G029 1975 |
| Деталь: | Sync Detector Holder |
| Парткод: | G070 1925 |
| Деталь: | Sync Detector Board |
| Парткод: | G070 5240 |
| Деталь: | Harness - FFC-LD |
| Парткод: | G070 5325 |
| Деталь: | Harness - LD Control Board-sync |
| Парткод: | G070 5342 |
| Деталь: | Shield Glass |
| Парткод: | G070 1903 |
| Деталь: | Harness - BCU-LD Power |
| Парткод: | G070 5321 |
| Деталь: | Positioning Pin |
| Парткод: | G070 1902 |
| Деталь: | Cleaner Grip |
| Парткод: | G070 1956 |
| Деталь: | Cleaner Shaft |
| Парткод: | G070 1953 |
| Деталь: | CLEANER |
| Парткод: | G070 1955 |
Коды ошибок
201
220
221
230
231
241
280
281
282
300
301
302
305
350
351
352
400
401
410
411
412
413
420
421
430
440
460
461
480
481
502
503
515
520
541
542
543
544
545
546
551
552
553
554
555
556
560
640
641
670
680
687
730
740
741
742
743
744
745
750
751
800
801
802
803
818
819
820
821
822
823
824
827
828
829
835
836
838
850
851
853
854
855
856
857
860
861
862
863
864
865
900
990
991
998
999
Описание
| Error code: | 201 |
| Display: | ERROR 201 COMMAND |
| Description: | PU F/W Flash write error (Reserved) |
| Causes: | • Defective polygon motor • Defective harness |
| Remedy: | 1. Connect the cable correctly. 2. Replace the engine control board. 3. Replace the laser scanning unit. 4. Check or replace the cable. |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 221 |
| Description: | Laser synchronizing detection error: start position [K]: LD1 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 241 |
| Display: | Service call 241:Error |
| Description: | LD error: Y The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 280 |
| Description: | Paper Jam Clear Paper Path Leave sheets in Finisher area 5 |
| Causes: | • Defective BCU • Poor electrical connection • Noise |
| Remedy: | Primary: Media has jammed in the Finisher Option. Open the finisher option front door to access the jammed pages. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “280 Paper Jam” on page 2-82. |
| Error code: | 281 |
| Description: | GAPCI communication error Data is transferred. - The CPU does not detect the communication ACK signal from GAPCI. |
| Causes: | • Defective BCU |
| Remedy: | Jam is detected at the fuser or the bridge unit. |
| Error code: | 282 |
| Description: | Staple Jam Check Stapler Remove Job from Finisher |
| Causes: | • Defective BCU |
| Remedy: | The stapler device detects a paper jam during normal stapler operation such as when printing and stapling jobs. Check stapler are for jam in accumulator or stapler. Remove stapler cartridge to check for staple jam. Note: After the error has been cleared, the printer does not reprint any pages which existed in the accumulator for stapling. The following actions can be taken while either the primary or secondary messages are displayed: Press Go to initiate priming and resume printing. |
| Error code: | 300 |
| Description: | High voltage power output error |
| Causes: | The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). |
| Remedy: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. |
| Error code: | 301 |
| Description: | Fuser web must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 305 |
| Display: | ERROR 305 USB TIME OUT |
| Description: | Charge Corona Wire Cleaner Error The charge wire cleaner did not: (1) come from the home position within 5 s, or (2) did return to the home position within 3.75 s due to wire cleaner overload. |
| Causes: | • Cleaner unit blocked or damaged • Until replacement parts become available, set SP2804 to "0" to disable the charge-corona cleaning function so the machine can operate. |
| Error code: | 350 |
| Description: | ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0 |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 351 |
| Description: | ID sensor error 2 The ID sensor output voltage is 5.0V and the PWM signal input to the ID sensor is 0 when checking the ID sensor pattern |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 352 |
| Description: | ID sensor error 3 For 2 s during the ID sensor pattern check, the ID sensor pattern edge voltage is not 2.5V or the pattern edge is not detected within 800 ms. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 400 |
| Display: | Open top cover 400: Paper size error |
| Description: | TM sensor error |
| Causes: | The CPU detected a low voltage of the positive reflection output under the threshold in the TM sensor. |
| Remedy: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. 1. Clean the TM sensors. 2. Replace the TM sensors. 3. Check the image transfer unit. 4. Turn the power Off and On. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 410 |
| Description: | ID sensor error: Development K. D evelopment gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | 1. Replace the ID/ MUSIC sensors. 2. Check the harness connection to the LD unit. 3. Replace the LD unit. 4. Check the harness connection to the CGB HVPS. 5. Replace the CGB HVPS. 6. Replace the developer. |
| Error code: | 411 |
| Display: | SVC 411 ERROR |
| Description: | IRQ timer 1 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 412 |
| Display: | SVC 412 ERROR |
| Description: | IRQ timer 2 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 413 |
| Display: | CAPSHTR CAPOFF |
| Description: | ID sensor error: Development Y. Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | 1. Replace the ID/ MUSIC sensors. 2. Check the harness connection to the LD unit. 3. Replace the LD unit. 4. Check the harness connection to the CGB HVPS. 5. Replace the CGB HVPS. 6. Replace the developer. |
| Error code: | 420 |
| Display: | ERROR 420 Z POSITION |
| Description: | Potential sensor error: Vd Adjustment K. The drum potential sensor detects 150V or more on the drum (Vd) for 0.7 msec. when the high voltage charge is supplied to the drum for the initial sampling before exposure. |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Drum worn |
| Remedy: | 1. Clean or replace the drum potential sensor. 2. Replace the drum unit. |
| Error code: | 421 |
| Display: | ERROR 421 !CHECK FILTER |
| Description: | Potential sensor error: Vd Adjustment C. The drum potential sensor detects 150V or more on the drum (Vd) for 0.7 msec. when the high voltage charge is supplied to the drum for the initial sampling before exposure. |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Drum worn |
| Remedy: | 1. Clean or replace the drum potential sensor. 2. Replace the drum unit. |
| Error code: | 430 |
| Description: | Quenching lamp error At the completion of auto process control initialization, the potential of the drum surface detected by the potential sensor is more than -400V, the prescribed value. |
| Causes: | • Quenching lamp defective • Quenching lamp harness disconnected • Quenching lamp connector loose, defective |
| Error code: | 440 |
| Description: | Transfer Output Error. A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 460 |
| Description: | DC Separation Corona Output Error A dc separation feedback voltage of less than 0.5 V was detected after more than 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 461 |
| Description: | Humidity sensor error The output is 4.5 V (or higher) or 0.3 V (or lower) for 12 seconds. |
| Causes: | • Short circuit in the humidity sensor • Defective circuit • Defective connector |
| Error code: | 480 |
| Display: | Remove paper 480: Stacker full |
| Description: | Agitator Motor Error |
| Causes: | The agitator motor error is detected twice for 10 msec during the initialization at power-on or after the cover is closed. |
| Remedy: | • Disconnected or defective harness • Defective agitator motor 1. Check or replace the harness. 2. Replace the agitator motor. |
| Error code: | 481 |
| Description: | OPC belt sensor error |
| Causes: | • Defective OPC belt unit • Dirty OPC belt • Loose connection • Defective OPC belt sensor • Defective input output device • Defective BCU |
| Error code: | 502 |
| Display: | Service Call 502: Error |
| Description: | Tray 2 must be rebuilt |
| Causes: | Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB. Too much paper in the tray. Paper or other material is jammed in the parts between the tray and motor. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB. |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 515 |
| Display: | ERROR 515 DETECTION ERROR |
| Description: | DADF belt should be replaced |
| Causes: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty Note • This problem will not issue the SC code on the operation panel. • The machine will prompt the operator to reset tray by opening and closing it. • If the problem persists, the machine will display again and the tray cannot be used. |
| Error code: | 520 |
| Description: | Replace optics filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 556 |
| Description: | Unstable fusing temperature (rear) The fusing temperature varies 50° C or more within 1 second, and this occurs 2 consecutive times. |
| Causes: | • Thermistor defective or out of position • Power supply unit defective |
| Error code: | 560 |
| Description: | Zero cross error The main switch is turned on; the fusing relay turns on. - 50 Hz or 60 Hz is not detected within 5 seconds. |
| Causes: | • Defective relay circuit • Defective PSU • Incorrect power supply |
| Error code: | 640 |
| Description: | Communication error: Engine Controller (Check sum error) Sum value is added each command frame. Sum check means: STX xx xx xx xx sum ETX -> The least significant 7 bits of xx + xx + xx+ xx is compared with the sum Example: STX 80h 81h 82h 83h 06h ETX -> 80h + 81h + 82h + 83h = 206h If sum value is 06h, data is correct. This SC is not displayed when it occurs; count is executed only by logging. |
| Causes: | Hard error with PCI |
| Remedy: | 1. Turn the main switch off and on. |
| Error code: | 641 |
| Description: | BICU control data transfer abnormal A sampling of the control data sent from the BICU reveals an abnormality. |
| Causes: | • Defective controller board • External noise • Defective BCU |
| Remedy: | 1. Replace the controller board. 2. Replace the BCU. |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 680 |
| Description: | BCU error |
| Causes: | • Defective BCU |
| Remedy: | 1. Replace the EEPROM. 2. Replace the engine control board. |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 741 |
| Description: | Finisher corner stapler rotation motor error The stapler does not return to its home position within the specified time after stapling. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Defective stapler rotation motor • Overload to the stapler rotation motor • Defective stapler rotation HP sensor |
| Remedy: | 1. Replace the stapler rotation motor. 2. Replace the stapler rotation HP sensor. |
| Error code: | 742 |
| Description: | Finisher stapler movement motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished for a certain time. For the 1000-sheet booklet finisher • The stapler HP sensor is not activated within the specified time after the stapler motor turned on. (first detection: jam error, consecutive twice detection SC code). |
| Causes: | • Motor overload • Loose connection of the stapler home position sensor • Loose connection of the stapler movement motor • Defective stapler home position sensor • Defective stapler movement motor |
| Remedy: | 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor. |
| Error code: | 743 |
| Description: | Booklet stapler motor error 1 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher The front stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | • Motor overload • Loose connection of the front stapler motor • Defective front stapler motor |
| Remedy: | Replace the front stapler motor. |
| Error code: | 744 |
| Description: | Booklet staple motor error 2 The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher The rear stapler unit saddle-stitch motor does not start operation within the specified time. |
| Causes: | • Motor overload • Loose connection of the rear stapler motor • Defective rear stapler motor |
| Remedy: | Replace the front stapler motor. |
| Error code: | 745 |
| Description: | Feed-Out Belt Motor Error (Finisher B830) The stack feed-out belt HP sensor does not activate within the specified time after the stack feed-out belt motor turns on. The 1st detection failure causes a jam error, and the 2nd failure causes this SC code. |
| Causes: | If the motor is operating • Stack feed-out HP sensor harness loose, broken, defective • Stack feed-out HP sensor defective If the motor is not operating: • Feed-out belt motor blocked by an obstruction • Feed-out belt motor harness loose, broken, defective • Feed-out belt motor defective • Booklet finisher main board defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the stack feed-out belt HP sensor. 4. Replace the feed-out belt motor. 5. Replace the finisher main board. |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 751 |
| Description: | Stack pressure solenoid error The stack pressure solenoid in the finisher is not operating. |
| Causes: | • Solenoid harness loose, broken • Solenoid obstructed • Stack height sensor dirty, harness loose, broke • Solenoid defective • Stack height sensor defective |
| Error code: | 800 |
| Description: | Startup without video output end error (K) Video transfer to the engine is started, but the engine did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Error code: | 801 |
| Display: | SYSTEM HALT (*) 801 : (C)OPCODE |
| Description: | Video output error (Y) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 802 |
| Display: | SYSTEM HALT (*) 802 : (C)SLOT |
| Description: | Video output error (M) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 803 |
| Display: | SYSTEM HALT (*) 803 : (C)CPU ADDR |
| Description: | Video output error (C) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 835 |
| Display: | SYSTEM HALT (*) 835 : FW/PRN MDL |
| Description: | Self-diagnostic error: Centronic device |
| Causes: | [1102] Loopback connector is connected but check results in an error. • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [110C] Loopback connector is connected but check results in an error. • ASIC device error • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [1120] Centronic loopback connector is not connected for detailed self-diagnostic test. • Centronic loopback connector not connected correctly • Centronic loopback connector defective • ASIC device defective Replace the controller board. |
| Error code: | 836 |
| Display: | SYSTEM HALT (*) 836 : FW/SV MDL |
| Description: | Self-diagnostics error: Font ROM (standard) |
| Causes: | Turn the main switch off and on. Replace the standard ROM-DIMM. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the controller board. |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 850 |
| Description: | Net I/F error Duplicate IP addresses. Illegal IP address. Driver unstable and cannot be used on the network |
| Causes: | • IP address setting incorrect • NIB (PHY) board defective • Controller board defective |
| Remedy: | Turn the main switch off and on. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 862 |
| Description: | Bad sector number error The number of bad sectors in the HDD (image data area) goes over 101. |
| Causes: | • Defective HDD |
| Remedy: | Format the HDD with SP5832-001. Replace the HDD. |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
| Error code: | 999 |
| Display: | Service call 999: Error |
| Description: | Stapler Motor Error |
| Causes: | • Color registration (MUSIC) failure |
| Remedy: | 1 Are staples jammed in the stapler? Go to step 2. Go to step 3. 2 Clear the staple jam and run the staple test in diagnostic mode or run a staple job. Does the problem reoccur? Replace the staple cartridge and to go step 4. Problem solved. 3 Are the connectors CN5 on the stapler and PJ1 on the finisher control board securely connected? Go to step 5. Securely connect the connectors. 4 Did replacement of the stapler cartridge resolve the problem? Problem resolved. Replace the stapler. 5 Make sure the finisher set switch is activated. Measure for 5 V dc between pins 11 and 12 on stapler connector CN5. Is 5 V dc present? Replace the stapler. Replace the finisher control board. 6 Did replacement of the finisher control board correct the problem? Problem solved. Go to step 7. 7 Is there continuity on the stapler to finisher control board cable? Replace the power supply. Replace the cable. |
