Samsung CLP-610ND
Рейтинг
Модули
SCF Unit
Exit Cover
TOP COVER
Fuser drive
Feed Drive
OPE Unit
Front Cover
CASSETTE
Fuser
CASSETTE ASSEMBLY
Cover Unit
MP TRAY
PTB Unit
MAIN
SCF Cassette
FRAME
Детали Feed Drive
| Деталь: | ELA HOU-UNIT_SCF |
| Парткод: | JC96-04502A |
| Деталь: | ELA Unit-Idle_SCF |
| Парткод: | JC96-04019A |
| Деталь: | MEA UNIT-P/UPJHOUSING |
| Парткод: | JC97-02233A |
| Цена: | 460 ₽ |
| Деталь: | MEA UNIT-GEARjPICKjUP |
| Парткод: | JC97-02691A |
| Деталь: | As-Unit_Feed1 |
| Парткод: | JC81-03458A |
| Цена: | 460 ₽ |
| Деталь: | ELA Hou-Cst Sensor Hawk16 |
| Парткод: | JC96-02127A |
| Деталь: | MEA UNIT-TERMINALTR |
| Парткод: | JC97-01401A |
| Деталь: | ELA Unit-Motor SCF |
| Парткод: | JC96-03956A |
| Деталь: | ELA HOU-UNITjCASSETTE |
| Парткод: | JC96-04503A |
| Деталь: | Gear-Feed |
| Парткод: | JC66-01262A |
| Деталь: | SHAFT-PICK UPjSCF |
| Парткод: | JC66-01277A |
| Деталь: | Ring-CS |
| Парткод: | 6044-000001 |
| Деталь: | HOLDER-PICKjUPjSCF |
| Парткод: | JC61-01743A |
| Деталь: | Spring-TS |
| Парткод: | 6107-001170 |
| Деталь: | Ring-E |
| Парткод: | 6044-000125 |
| Деталь: | SHAFT-FEEDjSCF |
| Парткод: | JC66-01276A |
| Деталь: | GROUND-PJMOTORJSCF |
| Парткод: | JC63-01137A |
| Деталь: | SHEET-GUIDEjPATH |
| Парткод: | JC63-01163A |
| Деталь: | HOLDER-P-REGI |
| Парткод: | JC61-01579A |
| Деталь: | Bearing-Pick Up |
| Парткод: | JC66-10202A |
| Деталь: | BRUSH-PICK |
| Парткод: | JC67-00204A |
| Деталь: | GROUND-PjFRONTjBOTTOM |
| Парткод: | JC63-01136A |
| Деталь: | Foot-ML80 |
| Парткод: | JC61-40001A |
| Деталь: | GROUND-PJREARJBOTTOM |
| Парткод: | JC63-01140A |
| Деталь: | PLATE-GNDjREARjTOP |
| Парткод: | JC61-01904A |
| Деталь: | PLATE-GNDjFRAMEjSCF |
| Парткод: | JC61-01903A |
| Деталь: | GROUND-PjSHAFT |
| Парткод: | JC63-01141A |
| Деталь: | PMO-REMOVEjLOCKjCST |
| Парткод: | JC72-01355A |
| Деталь: | GROUND-P-PAPERjSIZE |
| Парткод: | JC63-00675A |
| Деталь: | BAR-PJCROSS BOTTOM |
| Парткод: | JC71-00042A |
| Деталь: | COVER-M-DUMMYjSCF |
| Парткод: | JC63-00686A |
| Деталь: | IPR-GROUND TOP |
| Парткод: | JC70-11028A |
| Деталь: | PMO-ACTUATOR EMPTY,SCF |
| Парткод: | JC72-00992A |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | 0604-001095 |
| Деталь: | COVER-FRONTjSCF |
| Парткод: | JC63-01305A |
| Деталь: | COVER-LEFTJSCF |
| Парткод: | JC63-01303A |
| Деталь: | Solenoid-Main |
| Парткод: | JC33-00012A |
| Деталь: | COVER-RIGHTjSCF |
| Парткод: | JC63-01304A |
| Деталь: | FRAME-SCF |
| Парткод: | JC61-01902A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | MEA-COVER EXIT |
| Парткод: | JC97-02847A |
| Деталь: | COVER-EXIT |
| Парткод: | JC63-01289A |
| Деталь: | COVER-FUSER EXIT |
| Парткод: | JC63-01299A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | MEC-Brush Antistatic |
| Парткод: | JC75-00095A |
| Деталь: | GROUND-EXIT |
| Парткод: | JC63-01277A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000282 |
| Деталь: | ELA-COVER TOP |
| Парткод: | JC96-04415A |
| Деталь: | ELA-COVER TOP |
| Парткод: | JC96-04415B |
| Деталь: | ELA-COVER TOP |
| Парткод: | JC96-04415C |
| Деталь: | Cover-Top |
| Парткод: | JC63-01278A |
| Деталь: | PMO-STACKER RX |
| Парткод: | JC72-01346D |
| Деталь: | MEA COVER-EXIT |
| Парткод: | JC97-02847A |
| Деталь: | ELA-OPE |
| Парткод: | JC96-04416A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | ELA UNIT-FUSER DRIVE |
| Парткод: | JC96-04501A |
| Деталь: | ELA UNIT-FUSER BLDC |
| Парткод: | JC96-04501B |
| Деталь: | BRACKET-FUSER DRIVE L |
| Парткод: | JC61-01859A |
| Деталь: | GEAR-IDLE EXIT |
| Парткод: | JC66-01 371 A |
| Деталь: | GEAR-IDLE DEVE |
| Парткод: | JC66-01 393A |
| Деталь: | GEAR-RDCN FU |
| Парткод: | JC66-01 392A |
| Деталь: | GEAR-IDLE DEVE |
| Парткод: | JC66-01 368A |
| Деталь: | GEAR- RDCN FU |
| Парткод: | JC66-01386A |
| Деталь: | GEAR- RDCN FU |
| Парткод: | JC66-01927A |
| Деталь: | GEAR-RDCN FU |
| Парткод: | JC66-01 387A |
| Деталь: | GEAR-RDCN FU |
| Парткод: | JC66-01 388A |
| Деталь: | GEAR-RDCN EXIT |
| Парткод: | JC66-01 381 A |
| Деталь: | BUSH-D6/L4 |
| Парткод: | JC61 -00699A |
| Деталь: | SHAFT-CLUTCH FU |
| Парткод: | JC66-01341A |
| Деталь: | GEAR-IDLE DEVE |
| Парткод: | JC66-01 366A |
| Деталь: | CLUTCH-BK DEVE |
| Парткод: | JC47-00006D |
| Деталь: | GEAR-DRV FU |
| Парткод: | JC66-01 362A |
| Деталь: | LATCH-M-HUB CLUTCH |
| Парткод: | JC66-01 070A |
| Деталь: | GEAR-FUSER RDCN OUT V |
| Парткод: | JC66-01155A |
| Деталь: | BRACKET-FUSER DRIVE R |
| Парткод: | JC61-01860A |
| Деталь: | BRACKET-FUSER R BLDC |
| Парткод: | JC61-01860B |
| Деталь: | MOTOR STEP |
| Парткод: | JC31 -00076A |
| Деталь: | Motor BLDC |
| Парткод: | JC31 -00090A |
| Деталь: | GUIDE-FUSER R |
| Парткод: | JC61 -01 851 A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000301 |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000269 |
| Деталь: | PMO-IMPELLER_DRV |
| Парткод: | JC72-00825A |
| Деталь: | MEA UNIT-FEED DRIVE |
| Парткод: | JC97-02854A |
| Деталь: | GEAR-RDCN FEED(79/39) |
| Парткод: | JC66-01385A |
| Деталь: | GEAR-RDCN FEED(43/23) |
| Парткод: | JC66-01383A |
| Деталь: | GEAR-RDCN FEED(35/22) |
| Парткод: | JC66-01382A |
| Деталь: | GEAR-DRV MAIN PICK-UP |
| Парткод: | JC66-01363A |
| Деталь: | GEAR-RDCN FEED(55/54) |
| Парткод: | JC66-01384A |
| Деталь: | BRACKET-FEED DRIVE |
| Парткод: | JC61-01835A |
| Деталь: | ELA-OPE |
| Парткод: | JC96-04416A |
| Деталь: | ELA-OPE |
| Парткод: | JC96-04416B |
| Деталь: | ELA-OPE |
| Парткод: | JC96-04416C |
| Деталь: | Cover-OPE |
| Парткод: | JC63-01300A |
| Деталь: | Cover-OPE |
| Парткод: | JC63-01300B |
| Деталь: | Cover-OPE |
| Парткод: | JC63-01300C |
| Деталь: | KEY-STOP |
| Парткод: | JC64-00301A |
| Деталь: | KEY-MENU |
| Парткод: | JC64-00300A |
| Деталь: | LENS-STATUS |
| Парткод: | JC67-00218A |
| Деталь: | HOLDER-LCD |
| Парткод: | JC61-01847A |
| Деталь: | PBA SUB-OPE |
| Парткод: | JC92-01872A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | MEA-Cover Front |
| Парткод: | JC97-02846A |
| Деталь: | Cover-Front |
| Парткод: | JC63-01274A |
| Деталь: | SUPPORT-PTB R |
| Парткод: | JC61-01849A |
| Деталь: | SUPPORT-PTB L |
| Парткод: | JC61-01848A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | LEVER-PTB |
| Парткод: | JC66-01354A |
| Деталь: | Spring ETC-Guide Deve |
| Парткод: | JC61-00038A |
| Деталь: | BRACKET-P-COVER LOCK |
| Парткод: | JC61-01050A |
| Деталь: | KNOB-HANDLE |
| Парткод: | JC64-00299A |
| Деталь: | LOCKER-FRONT R |
| Парткод: | JC64-00306A |
| Деталь: | LOCKER-FRONT L |
| Парткод: | JC64-00305A |
| Деталь: | HOLDER-LOCKER FRONT R |
| Парткод: | JC61-01843A |
| Деталь: | HOLDER-LOCKER FRONT L |
| Парткод: | JC61-01842A |
| Деталь: | Spring-ES |
| Парткод: | 6107-001138 |
| Деталь: | HOLDER-KNOB HANDLE |
| Парткод: | JC61-01841A |
| Деталь: | COVER-FRONT PATH |
| Парткод: | JC63-01290A |
| Деталь: | LEVER-COUPLING R |
| Парткод: | JC66-01353A |
| Деталь: | LEVER-COUPLING L |
| Парткод: | JC66-01352A |
| Деталь: | LEVER-PTB TOP |
| Парткод: | JC66-01421A |
| Деталь: | Spring-CS |
| Парткод: | 6107-001345 |
| Деталь: | MEA-TRAY MP |
| Парткод: | JC97-02894A |
| Деталь: | ELA HOU-UNIT_CASSETTE |
| Парткод: | JC96-04498A |
| Деталь: | MEA UNIT-REGISTRATION |
| Парткод: | JC97-02897A |
| Деталь: | MEA-KNOCK_UP_PLATE |
| Парткод: | JC97-02888A |
| Деталь: | MEA-GUIDE_EXETENSION |
| Парткод: | JC97-02887A |
| Деталь: | MEA UNIT-GEAR_BASE |
| Парткод: | JC97-02889A |
| Деталь: | MEA-GEAR PICKUP_MP |
| Парткод: | JC97-02893A |
| Деталь: | MEA-COVER_CASSETTE |
| Парткод: | JC97-02885A |
| Деталь: | MEA-HOLDER PAD_MP |
| Парткод: | JC97-02892A |
| Цена: | 500 ₽ |
| Деталь: | MEA-KNOCK_UP PLATE_MP |
| Парткод: | JC97-02891A |
| Деталь: | ELA Unit-Roller P/Up MP |
| Парткод: | JC96-02686B |
| Деталь: | MEA-GUIDE PAPER DUP |
| Парткод: | JC97-02890A |
| Деталь: | MEA-HOLDER_PAD_SHEET |
| Парткод: | JC97-03077A |
| Деталь: | PMO-Idle Pick Up MP |
| Парткод: | JC72-01003A |
| Деталь: | SHAFT-MP_PICK_UP |
| Парткод: | JC66-01348A |
| Деталь: | COVER-DRAW_CONNECTOR |
| Парткод: | JC63-01286A |
| Деталь: | HARNESS-MP DRAWER_MP |
| Парткод: | JC39-00659A |
| Деталь: | GROUND-REGI_BRKT |
| Парткод: | JC63-01282A |
| Деталь: | ACTUATOR-FEED_EMPTY |
| Парткод: | JC66-01403A |
| Деталь: | PHOTO-INTERRUPTER |
| Парткод: | 0604-001095 |
| Деталь: | GUIDE-PAPER_MPF |
| Парткод: | JC61-01865A |
| Деталь: | Roller-Feed |
| Парткод: | JC66-01347A |
| Деталь: | PMO-PLATE_LOCKER |
| Парткод: | JC72-00972A |
| Деталь: | Spring Etc-Locker,Plate |
| Парткод: | JG61-70531A |
| Деталь: | Spring-CS |
| Парткод: | 6107-001166 |
| Цена: | 280 ₽ |
| Деталь: | ADJUST-M-CASSETTE_L |
| Парткод: | JC70-00300A |
| Деталь: | ADJUST-M-CASSETTE_R |
| Парткод: | JC70-00301A |
| Деталь: | PLATE-GND_KNOCKUP |
| Парткод: | JC61-01940A |
| Деталь: | SHEET-MPF |
| Парткод: | JC63-01291A |
| Деталь: | PLATE-GND-BRKT-GEAR |
| Парткод: | JC61-01923A |
| Деталь: | HOLDER-_M_GEAR REGI |
| Парткод: | JC61-01128A |
| Деталь: | Spring-CS |
| Парткод: | 6107-001249 |
| Деталь: | GEAR-M-REGI |
| Парткод: | JC66-00774A |
| Деталь: | HOLDER-_M_CLUTCH GEAR |
| Парткод: | JC61-01127A |
| Деталь: | COVER-GEAR_BOX |
| Парткод: | JC63-01285A |
| Деталь: | SOLENOID-PICK_UP |
| Парткод: | JC33-00022A |
| Цена: | 600 ₽ |
| Деталь: | LEVER-LINK_INDICATOR |
| Парткод: | JC66-01355A |
| Деталь: | Gear-Pinion |
| Парткод: | JG66-40003A |
| Цена: | 260 ₽ |
| Деталь: | ROLLER-IDLE FEED |
| Парткод: | JC66-00764A |
| Деталь: | SPRING ETC-ROLLER |
| Парткод: | JC61-01274A |
| Деталь: | PMO-Bearing Shaft |
| Парткод: | JC72-41191B |
| Цена: | 430 ₽ |
| Деталь: | BUSH-D6/L4 |
| Парткод: | JC61-00699A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | Ring-E |
| Парткод: | 6044-000125 |
| Деталь: | FRAME-CASSETTE |
| Парткод: | JC61-01856A |
| Деталь: | HOLDER-PAD |
| Парткод: | JC61-02159A |
| Деталь: | RPR-FRICTION PAD |
| Парткод: | JC73-00140A |
| Цена: | 90 ₽ |
| Деталь: | PLATE-PAD |
| Парткод: | JC61-02237A |
| Деталь: | SHEET PAD |
| Парткод: | JC63-01669A |
| Деталь: | GROUND-PAD |
| Парткод: | JC63-01205A |
| Деталь: | Spring Etc-Exit Roll FD |
| Парткод: | JC61-70911A |
| Деталь: | HOUSING-HOLDER PAD |
| Парткод: | JC61-01978A |
| Цена: | 280 ₽ |
| Деталь: | ELA UNIT-FUSER LV,CLP-660 |
| Парткод: | JC96-04495A |
| Деталь: | ELA UNIT-FUSER HV,CLP-660 |
| Парткод: | JC96-04496A |
| Цена: | 10 200 ₽ |
| Деталь: | ELA UNIT-FUSER LV,CLP-610 |
| Парткод: | JC96-04544A |
| Деталь: | ELA UNIT-FUSER HV,CLP-610 |
| Парткод: | JC96-04545A |
| Цена: | 9 700 ₽ |
| Деталь: | COVER-FUSER_LOWER |
| Парткод: | JC63-01312A |
| Деталь: | Guide-INPUT |
| Парткод: | JC61-01933A |
| Деталь: | LEVER-JAM_L |
| Парткод: | JC66-01417A |
| Деталь: | LEVER-JAM_R |
| Парткод: | JC66-01416A |
| Деталь: | Roller-Pressure |
| Парткод: | JC66-01412A |
| Деталь: | BRACKET-PR_R |
| Парткод: | JC61-01917A |
| Деталь: | BRACKET-PR_L |
| Парткод: | JC61-01916A |
| Деталь: | Bearing-Ball |
| Парткод: | 6601-001341 |
| Деталь: | GROUND-PR |
| Парткод: | JC63-01308A |
| Деталь: | GROUND-PR_SUB |
| Парткод: | JC63-01335A |
| Деталь: | ACTUATOR-FUSER |
| Парткод: | JC66-01404A |
| Деталь: | GUIDE-ACTUATOR |
| Парткод: | JC61-01938A |
| Деталь: | Spring ETC-Actuator |
| Парткод: | JC61-70903A |
| Деталь: | Spring-ES |
| Парткод: | 6107-001323 |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000269 |
| Деталь: | SCREW-HEX |
| Парткод: | 6009-001492 |
| Деталь: | BRACKET-FUSER |
| Парткод: | JC61-01915A |
| Деталь: | HOLDER-BRACKET |
| Парткод: | JC61-01931A |
| Деталь: | SUPPORT-BRACKET |
| Парткод: | JC61-01921A |
| Деталь: | Spring-ES |
| Парткод: | 6107-001324 |
| Деталь: | DRUM-FUSER_BELT |
| Парткод: | JC66-01413A |
| Деталь: | ROLLER-HEAT |
| Парткод: | JC66-01411A |
| Деталь: | LAMP-HALOGEN,CLP-660 |
| Парткод: | 4713-001221 |
| Деталь: | LAMP-HALOGEN,CLP-660 |
| Парткод: | 4713-001222 |
| Деталь: | LAMP-HALOGEN,CLP-610 |
| Парткод: | 4713-001229 |
| Деталь: | LAMP-HALOGEN,CLP-610 |
| Парткод: | 4713-001228 |
| Деталь: | BUSH-HR |
| Парткод: | JC61-01928A |
| Деталь: | GEAR-FUSER |
| Парткод: | JC66-01405A |
| Деталь: | Bearing-Ball |
| Парткод: | 6601-001478 |
| Деталь: | ROLLER-FUSER |
| Парткод: | JC66-01410A |
| Деталь: | Ring-E |
| Парткод: | 6044-000231 |
| Деталь: | Ring-E |
| Парткод: | 6044-000125 |
| Деталь: | BRACKET-HR |
| Парткод: | JC61-01918A |
| Деталь: | Bearing-Ball |
| Парткод: | 6601-001479 |
| Цена: | 1 400 ₽ |
| Деталь: | THERMISTOR-NTC ASSY |
| Парткод: | 1404-001355 |
| Деталь: | HOLDER-LAMP |
| Парткод: | JC61-01920A |
| Деталь: | THERMOSTAT |
| Парткод: | 4712-001039 |
| Деталь: | COVER-FUSER_UPPER |
| Парткод: | JC63-01311A |
| Деталь: | BRACKET-FU_DRIVE |
| Парткод: | JC61-01919A |
| Деталь: | GEAR-IDLE Z15 |
| Парткод: | JC66-01406A |
| Деталь: | GEAR-IDLE Z39 |
| Парткод: | JC66-01407A |
| Деталь: | GROUND-UPPER |
| Парткод: | JC63-01309A |
| Деталь: | GROUND-LOWER |
| Парткод: | JC63-01307A |
| Деталь: | HOLDER-CONNECTOR |
| Парткод: | JC61-01929A |
| Деталь: | HARNESS-FUSER DRAW_F,CLP-661 |
| Парткод: | JC39-00667A |
| Деталь: | HARNESS-FUSER DRAW_F,CLP-661 |
| Парткод: | JC39-00668A |
| Деталь: | HARNESS-FUSER DRAW_F,CLP-611 |
| Парткод: | JC39-00768A |
| Деталь: | HARNESS-FUSER DRAW_F,CLP-611 |
| Парткод: | - |
| Деталь: | GUIDE-OUTPUT |
| Парткод: | JC61-01934A |
| Деталь: | ROLLER-EXIT IDLE |
| Парткод: | JC66-00608A |
| Деталь: | GROUND-EXIT |
| Парткод: | JC63-01310A |
| Деталь: | BUSH-6_D |
| Парткод: | JC61-00423A |
| Деталь: | Spring Etc-Exit Roll FD |
| Парткод: | JC61-70911A |
| Деталь: | HOLDER-EXIT(MC) |
| Парткод: | JC61-00547A |
| Деталь: | ROLLER-FD R |
| Парткод: | JC66-01233A |
| Деталь: | PMO-Roller FD F |
| Парткод: | JC72-41007A |
| Деталь: | ROLLER-EXIT |
| Парткод: | JC66-01415A |
| Деталь: | GEAR-_M_EXIT |
| Парткод: | JC66-00782A |
| Деталь: | GUIDE-DUPLEX |
| Парткод: | JC61-01935A |
| Деталь: | HANDLE-FUSER_R |
| Парткод: | JC64-00311A |
| Деталь: | LOCKER-FUSER_R |
| Парткод: | JC64-00309A |
| Деталь: | HANDLE-FUSER_L |
| Парткод: | JC64-00312A |
| Деталь: | LOCKER-FUSER_L |
| Парткод: | JC64-00310A |
| Деталь: | SPRING ETC-DEVE REAR |
| Парткод: | JC61-00550A |
| Деталь: | HOLDER-HARNESS |
| Парткод: | JC61-01930A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000282 |
| Деталь: | FELT-CLEAN TONER |
| Парткод: | JC63-00903 |
| Деталь: | Датчик наличия бумаги |
| Парткод: | 0604-001415 |
| Цена: | 240 ₽ |
| Деталь: | Резиновый элемент на ролик захвата бумаги из основного лотка |
| Парткод: | JC73-00223A |
| Цена: | 350 ₽ |
| Деталь: | MEA UNIT-COVER |
| Парткод: | JC97-02941A |
| Деталь: | MEA UNIT-COVER |
| Парткод: | JC97-02941B |
| Деталь: | MEA UNIT-COVER |
| Парткод: | JC97-02941C |
| Деталь: | MEA UNIT-COVER |
| Парткод: | - |
| Деталь: | ELA-COVER TOP |
| Парткод: | JC96-04415A |
| Деталь: | ELA-COVER TOP |
| Парткод: | JC96-04415B |
| Деталь: | ELA-COVER TOP |
| Парткод: | JC96-04415C |
| Деталь: | ELA-COVER TOP |
| Парткод: | - |
| Деталь: | COVER-TOP SUB |
| Парткод: | JC63-01279A |
| Деталь: | COVER-LEFT |
| Парткод: | JC63-01275A |
| Деталь: | FAN |
| Парткод: | JC31-00050A |
| Деталь: | COVER-RIGHT |
| Парткод: | JC63-01276A |
| Деталь: | MEA-BRACKET REAR |
| Парткод: | JC97-03052A |
| Деталь: | MEA-Cover Front |
| Парткод: | JC97-02846A |
| Деталь: | SHAFT-HINGE LINK |
| Парткод: | JC66-00835A |
| Деталь: | HOLDER-LINK FRONT |
| Парткод: | JC61-01846A |
| Деталь: | LINK-SUPPORT |
| Парткод: | JC66-01358A |
| Деталь: | Cover-Rear |
| Парткод: | JC61-02211A |
| Деталь: | COVER-REAR HDD |
| Парткод: | JC63-01314A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000269 |
| Деталь: | MEA-TRAY MP |
| Парткод: | JC97-02894A |
| Деталь: | COVER-MP_TRAY |
| Парткод: | JC63-01287A |
| Деталь: | TRAY-ASF_INPUT |
| Парткод: | JC63-01293A |
| Деталь: | LINK-TRAY_MP_L |
| Парткод: | JC66-01349A |
| Деталь: | LINK-TRAY_MP_R |
| Парткод: | JC66-01350A |
| Деталь: | Gear-Pinion |
| Парткод: | JG66-40003A |
| Цена: | 260 ₽ |
| Деталь: | GUIDE-_M_SIDE MP L |
| Парткод: | JC61-01043A |
| Деталь: | GUIDE-_M_SIDE MP R |
| Парткод: | JC61-01042A |
| Деталь: | ELA UNIT-PTB SET_DUPLEX |
| Парткод: | JC96-04406A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000282 |
| Деталь: | PIN-SPRING |
| Парткод: | 6043-001097 |
| Деталь: | Spring-CS |
| Парткод: | 6107-001364 |
| Деталь: | Spring-CS |
| Парткод: | 6107-001365 |
| Деталь: | Spring-ES |
| Парткод: | 6107-001316 |
| Деталь: | BUSH-D6/L4 |
| Парткод: | JC61-00699A |
| Деталь: | BUSH-6_D(L) |
| Парткод: | JC61-00884A |
| Деталь: | HOLDER-M-TENSION |
| Парткод: | JC61-01092A |
| Деталь: | HOLDER-M-TRANSFER |
| Парткод: | JC61-01093A |
| Деталь: | SPRING ETC-DEV_FRONT |
| Парткод: | JC61-01678A |
| Деталь: | PLATE-SAW FUSER |
| Парткод: | JC61-01754A |
| Деталь: | HOLDER-PAPER C,L |
| Парткод: | JC61-01820A |
| Деталь: | HOLDER-PAPER C,R |
| Парткод: | JC61-01821A |
| Деталь: | HOLDER-DRAW |
| Парткод: | JC61-01822A |
| Деталь: | FRAME-PTB |
| Парткод: | JC61-01823A |
| Деталь: | FRAME-DUMMY, L |
| Парткод: | JC61-01824A |
| Деталь: | FRAME-DUMMY,R |
| Парткод: | JC61-01825A |
| Деталь: | GUIDE-BELT |
| Парткод: | JC61-01826A |
| Деталь: | GUIDE-DRIVE |
| Парткод: | JC61-01827A |
| Деталь: | PLATE-DUMMY TENSION |
| Парткод: | JC61-01828A |
| Деталь: | PLATE-GROUND BACKUP |
| Парткод: | JC61-01829A |
| Деталь: | PLATE-GROUND PTB |
| Парткод: | JC61-01830A |
| Деталь: | PLATE-GROUND TENSION |
| Парткод: | JC61-01831A |
| Деталь: | PLATE-HV PCR |
| Парткод: | JC61-01832A |
| Деталь: | PLATE-HV TR_M |
| Парткод: | JC61-01833A |
| Деталь: | PLATE-HV TR_Y |
| Парткод: | JC61-01834A |
| Деталь: | PLATE-GND RESISTANCE |
| Парткод: | JC61-02179A |
| Деталь: | SEAL-WASTE BOTTOM |
| Парткод: | JC62-00163A |
| Деталь: | SEAL-WASTE FILM |
| Парткод: | JC62-00166A |
| Деталь: | SEAL-BLADE PTB,L |
| Парткод: | JC62-00355A |
| Деталь: | SEAL-BLADE PTB,R |
| Парткод: | JC62-00356A |
| Деталь: | SEAL-BRKT PTB,L |
| Парткод: | JC62-00357A |
| Деталь: | SEAL-BRKT PTB,R |
| Парткод: | JC62-00358A |
| Деталь: | COVER-DUPLEX GEAR |
| Парткод: | JC63-01267A |
| Деталь: | COVER-UPPER PTB |
| Парткод: | JC63-01268A |
| Деталь: | COVER-HANDLE INNER |
| Парткод: | JC63-01269A |
| Деталь: | COVER-WASTE TONER,L |
| Парткод: | JC63-01270A |
| Деталь: | COVER-WASTE TONER,U |
| Парткод: | JC63-01271A |
| Деталь: | HANDLE-LOCKER PTB |
| Парткод: | JC64-00296A |
| Деталь: | LOCKER-PTB,L |
| Парткод: | JC64-00297A |
| Деталь: | LOCKER-PTB,R |
| Парткод: | JC64-00298A |
| Деталь: | ROLLER-PAPER CHARGE |
| Парткод: | JC66-00918A |
| Деталь: | ROLLER-TENSION,PTB |
| Парткод: | JC66-00920A |
| Деталь: | Roller-Transfer |
| Парткод: | JC66-00922B |
| Деталь: | SHAFT-P-LOCKBAR REAR |
| Парткод: | JC66-01089A |
| Деталь: | GEAR-DUP DRIVE Z34 |
| Парткод: | JC66-01322A |
| Деталь: | GEAR-DUP IDLE Z33 |
| Парткод: | JC66-01323A |
| Деталь: | GEAR-DUP RDCN Z2923 |
| Парткод: | JC66-01324A |
| Деталь: | GEAR-DUP IDLE Z21 |
| Парткод: | JC66-01325A |
| Деталь: | ROLLER-DRIVE PTB |
| Парткод: | JC66-01331A |
| Деталь: | ROLLER-BACKUP CLEAN |
| Парткод: | JC66-01332A |
| Деталь: | DRUM-PTB BELT |
| Парткод: | JC66-01333A |
| Деталь: | COUPLER-PTB |
| Парткод: | JC67-00213A |
| Деталь: | MEA UNIT-CLEANING PTB |
| Парткод: | JC97-02247B |
| Деталь: | BRACKET-P-CLN,PTB |
| Парткод: | JC61-01109A |
| Деталь: | BLADE-CLEANING PTB |
| Парткод: | JC61-01280B |
| Деталь: | PBA SUB-PTB CRUM |
| Парткод: | JC92-01868A |
| Деталь: | SENSOR-CTD |
| Парткод: | JC32-00006A |
| Деталь: | HARNESS-PTB DRAW_P |
| Парткод: | JC39-00664A |
| Деталь: | HARNESS-ACR_SENSOR |
| Парткод: | JC39-00653A |
| Деталь: | R-METAL GLAZE |
| Парткод: | 2009-001197 |
| Деталь: | MEA UNIT-DUPLEX |
| Парткод: | JC97-02898A |
| Деталь: | Belt-Timing Gear |
| Парткод: | 6602-001084 |
| Деталь: | Bush-M-Feed, Dup |
| Парткод: | JC61-00665A |
| Деталь: | Spring ETC-Dup |
| Парткод: | JC61-01277A |
| Деталь: | GUIDE-ALIGN-DUP |
| Парткод: | JC61-01839A |
| Деталь: | GROUND-ALIGN_DUP |
| Парткод: | JC63-01297A |
| Деталь: | Shaft-Idle Roll, Dup |
| Парткод: | JC66-00444A |
| Деталь: | Roller-M-Idle_ Dup |
| Парткод: | JC66-00896A |
| Деталь: | Pulley-M-18-Dummy_Dup |
| Парткод: | JC66-00900A |
| Деталь: | Roller-Feed_Dup |
| Парткод: | JC66-00901A |
| Деталь: | GEAR |
| Парткод: | JC66-01400A |
| Деталь: | BRUSH-DUPLEX |
| Парткод: | JC67-00205A |
| Деталь: | ICT-Stud Paper Guide, Dp |
| Парткод: | JC70-00457A |
| Деталь: | PCT-SILP WASHER |
| Парткод: | JK72-00058A |
| Деталь: | ELA HOU-MAIN_SODIMM,CLP-660 |
| Парткод: | JC96-04583A |
| Деталь: | ELA HOU-MAIN_SODIMM,CLP-660 |
| Парткод: | JC96-04583B |
| Деталь: | PBA SUB-RAM DIMM,128MB |
| Парткод: | JC92-01889A |
| Деталь: | ELA HOU-MAIN_SODIMM,CLP-610 |
| Парткод: | JC96-04841A |
| Деталь: | PBA-RAM DIMM,DDR2 |
| Парткод: | JC92-01923A |
| Деталь: | A4 CLBP,GDI,N/W,DUPLEX |
| Парткод: | CLP-610ND |
| Деталь: | A4 CLBP,PCL,N/W,DUPLEX |
| Парткод: | CLP-660ND |
| Деталь: | A4 CLBP,PCL,N/W |
| Парткод: | CLP-660N |
| Деталь: | ELA UNIT-MAIN_FRAME |
| Парткод: | JC96-04490A |
| Деталь: | ELA UNIT-MAIN_FRAME |
| Парткод: | JC96-04490B |
| Деталь: | LINK-HINGE |
| Парткод: | JC66-01422A |
| Деталь: | HVPS |
| Парткод: | JC44-00136A |
| Деталь: | ELA Unit-Lsu |
| Парткод: | JC96-04500A |
| Деталь: | GUIDE-_M_BUSH HARNESS S |
| Парткод: | JC61-01012A |
| Деталь: | ELA UNIT-DUCT_FUSER |
| Парткод: | JC96-04487A |
| Деталь: | FAN-DC |
| Парткод: | JC31-00072A |
| Деталь: | ELA UNIT-BRACKET_MAIN |
| Парткод: | JC96-04864A |
| Деталь: | SMPS-PSP_TYPE4_V1 |
| Парткод: | JC44-00091A |
| Деталь: | SMPS-PSP_TYPE4_V2C |
| Парткод: | JC44-00092A |
| Деталь: | FDB-MULTI_TRIAC V2C,CLP-660 |
| Парткод: | JC44-00143A |
| Деталь: | FDB-MULTI_TRIAC V1,CLP-660 |
| Парткод: | JC44-00142A |
| Деталь: | FDB-SINGLE TRIAC V2C,CLP-610 |
| Парткод: | JC44-00153A |
| Деталь: | FDB-SINGLE TRIAC V1 ,CLP-610 |
| Парткод: | JC44-00152A |
| Деталь: | HARNESS-AC_INLET |
| Парткод: | JC39-00662A |
| Деталь: | BRACKET-DUMMY_POWER |
| Парткод: | JC61-01867A |
| Деталь: | BRACKET-MAIN |
| Парткод: | JC61-01866A |
| Деталь: | PBA-MAIN,CLP-660 |
| Парткод: | JC92-01870A |
| Деталь: | PBA-MAIN,CLP-660 |
| Парткод: | JC92-01870B |
| Деталь: | PBA-MAIN,CLP-610 |
| Парткод: | JC92-01949A |
| Деталь: | PBA-MAIN,CLP-610 |
| Парткод: | JC92-01949B |
| Деталь: | DAMPER-HINGE |
| Парткод: | JC66-01425A |
| Деталь: | FRAME-DAMPER_R |
| Парткод: | JC61-01911A |
| Деталь: | BRACKET-HINGE_R |
| Парткод: | JC61-01897A |
| Деталь: | FRAME-DAMPER_L |
| Парткод: | JC61-01912A |
| Деталь: | BRACKET-HINGE_L |
| Парткод: | JC61-01896A |
| Деталь: | CABLE CLAMP |
| Парткод: | 6502-001093 |
| Деталь: | ELA UNIT-FUSER LV,CLP-660 |
| Парткод: | JC96-04495A |
| Деталь: | ELA UNIT-FUSER HV,CLP-660 |
| Парткод: | JC96-04496A |
| Цена: | 10 200 ₽ |
| Деталь: | ELA UNIT-FUSER LV,CLP-610 |
| Парткод: | JC96-04544A |
| Деталь: | ELA UNIT-FUSER HV,CLP-610 |
| Парткод: | JC96-04545A |
| Цена: | 9 700 ₽ |
| Деталь: | MEA UNIT-COVER |
| Парткод: | JC97-02941C |
| Деталь: | MEA UNIT-COVER |
| Парткод: | JC97-02941A |
| Деталь: | MEA UNIT-COVER |
| Парткод: | JC97-02941B |
| Деталь: | ELA UNIT-DEV BK_SET |
| Парткод: | JC96-04391A |
| Деталь: | ELA UNIT-DEV C_SET |
| Парткод: | JC96-04392A |
| Деталь: | ELA UNIT-DEV M_SET |
| Парткод: | JC96-04393A |
| Деталь: | ELA UNIT-DEV Y_SET |
| Парткод: | JC96-04394A |
| Деталь: | ELA UNIT-PTB SET_DUPLEX |
| Парткод: | JC96-04406A |
| Деталь: | ELA HOU-UNIT_CASSETTE |
| Парткод: | JC96-04498A |
| Деталь: | ELA HOU-UNIT_SCF |
| Парткод: | JC96-04502A |
| Деталь: | USB cable |
| Парткод: | - |
| Деталь: | POWER CORD |
| Парткод: | - |
| Деталь: | FLAT CABLE, 410mm |
| Парткод: | JC39-00651A |
| Деталь: | FLAT CABLE, 390mm |
| Парткод: | JC39-00650A |
| Деталь: | ELA HOU-UNIT-CASSETTE |
| Парткод: | JC96-04503A |
| Деталь: | MEA-UNIT_HOLDER PAD |
| Парткод: | JC97-02844A |
| Деталь: | FRAME-M_CASSETTE |
| Парткод: | JC61-01220C |
| Деталь: | GUIDE-M-PAPER SIZE |
| Парткод: | JC61-01227A |
| Деталь: | FRACKET-P-EXTENTION |
| Парткод: | JC61-01223A |
| Деталь: | GUIDE-M_EXTENSION CST |
| Парткод: | JC61-01224C |
| Деталь: | KNOB-M_REAR |
| Парткод: | JC64-00190B |
| Деталь: | Spring Etc-Guide Paper |
| Парткод: | JC61-00414A |
| Деталь: | GUIDE-M-LOCK A |
| Парткод: | JC61-00267B |
| Деталь: | GUIDEM_REAR |
| Парткод: | JC61-01226B |
| Деталь: | Guide-P-Rear Paper CST |
| Парткод: | JC61-00751A |
| Деталь: | PMO-Locker Plate |
| Парткод: | JC72-41210A |
| Деталь: | SPRING ETC-LOCKER_PLATE |
| Парткод: | JC61-70531A |
| Деталь: | PLATE-P-KNOCK UP |
| Парткод: | JC61-01245A |
| Деталь: | Spring Etc-Plate K/Up |
| Парткод: | JC61-00455A |
| Деталь: | RPR-Pad Cassette |
| Парткод: | JC73-00141A |
| Цена: | 80 ₽ |
| Деталь: | Spring Etc-Exit Roll FD |
| Парткод: | JC61-70911A |
| Деталь: | Holder-M-Pad_Housing |
| Парткод: | JC61-01228A |
| Деталь: | GROUND-CASSETTE |
| Парткод: | JC63-01206A |
| Деталь: | Gear-Pinion |
| Парткод: | JC66-40003A |
| Деталь: | GUIDE-P-SIDE_L |
| Парткод: | JC67-01222A |
| Деталь: | CAP-M-GUIDE SIDE_L |
| Парткод: | JC67-00037A |
| Деталь: | GUIDE-P-SIDE_R |
| Парткод: | JC61-01244A |
| Деталь: | Guide-M_Side Lock |
| Парткод: | JC61-01225B |
| Деталь: | LEVER-INDICATOR_SCF |
| Парткод: | JC66-01409A |
| Деталь: | labelM-cassette |
| Парткод: | JC68-01552A |
| Деталь: | SHUTTER-PATH |
| Парткод: | JC64-00268A |
| Деталь: | Guide-Paper |
| Парткод: | JC61-01724A |
| Деталь: | COVER_HANDLE |
| Парткод: | JC63-01306A |
| Деталь: | SCREW-TAPPING |
| Парткод: | 6002-000440 |
| Деталь: | ELA UNIT-MAIN_FRAME |
| Парткод: | JC96-04490A |
| Деталь: | ELA UNIT-MAIN_FRAME |
| Парткод: | JC96-04490B |
| Деталь: | ELA UNIT-FRAME_BOTTOM |
| Парткод: | JC96-04480A |
| Деталь: | FRAME-LSU |
| Парткод: | JC61-01927A |
| Деталь: | ELA UNIT-DEVE_CRUM |
| Парткод: | JC96-04488A |
| Деталь: | ELA UNIT-FRAME_TOP |
| Парткод: | JC96-04479A |
| Деталь: | ELA UNIT-FRAME_TOP |
| Парткод: | JC96-04479B |
| Деталь: | SPONGE-SEALING_LSU |
| Парткод: | JC72-01379A |
| Деталь: | ELA UNIT-FUSER BLDC |
| Парткод: | JC96-04501B |
| Деталь: | ELA UNIT-FUSER DRIVE |
| Парткод: | JC96-04501A |
| Деталь: | SPRING ETC-LOCK_PTB_R |
| Парткод: | JC61-01879A |
| Деталь: | LOCKER-PTB_R |
| Парткод: | JC64-00303A |
| Деталь: | BRACKET-LOCKER_PTB_R |
| Парткод: | JC61-01869A |
| Деталь: | LEVER-FUSER FRAME |
| Парткод: | JC66-01300A |
| Деталь: | SCREW-HEX |
| Парткод: | 6009-001492 |
| Деталь: | BRACKET-LOCKER_PTB_L |
| Парткод: | JC61-01855A |
| Деталь: | LOCKER-PTB_L |
| Парткод: | JC64-00304A |
| Деталь: | SPRING ETC-LOCK_PTB_L |
| Парткод: | JC61-01899A |
| Деталь: | ELA UNIT-OPE_LEFT |
| Парткод: | JC96-04481A |
| Деталь: | ELA UNIT-FRAME_LEFT |
| Парткод: | JC96-04482A |
| Деталь: | MEA UNIT-COVER_OPEN |
| Парткод: | JC97-02883A |
| Деталь: | ELA UNIT-DUCT_FUSER |
| Парткод: | JC96-04487A |
| Деталь: | GUIDE-HARNESS_CABLE |
| Парткод: | JC61-01890A |
| Деталь: | Bar-P_Cross Bottom |
| Парткод: | JC71-00042A |
| Деталь: | ELA UNIT-FRAME_RIGHT |
| Парткод: | JC96-04485A |
| Деталь: | MEA UNIT-FEED DRIVE |
| Парткод: | JC97-02854A |
| Деталь: | MEA-GEAR PICK UP |
| Парткод: | JC97-02895A |
| Деталь: | CAP-MAIN PICK-UP GEAR |
| Парткод: | JC67-00215A |
| Деталь: | SOLENOID-PICK_UP |
| Парткод: | JC33-00022A |
| Цена: | 600 ₽ |
| Деталь: | PLATE-GND-SOLENOID |
| Парткод: | JC61-01922A |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000196 |
| Деталь: | Screw-Taptite |
| Парткод: | 6003-000269 |
| Деталь: | BUSH-6_D |
| Парткод: | JC61-00423A |
| Деталь: | FRAME-BOTTOM |
| Парткод: | JC61-01871A |
| Деталь: | GUIDE-PICK UP |
| Парткод: | JC61-01878A |
| Деталь: | MEC-Brush Antistatic |
| Парткод: | JC67-00295A |
| Деталь: | ELA Unit-Pick Up |
| Парткод: | JC96-04491A |
| Деталь: | SEAL-BOTTOM |
| Парткод: | JC62-00462A |
| Деталь: | SEAL-FILM SCATTERING |
| Парткод: | JC62-00364A |
| Деталь: | MEA-ROLLER_PICK UP |
| Парткод: | JC97-03132A |
Коды ошибок
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
Описание
| Error code: | 01 |
| Display: | ERROR CONDITION INVALID HEAD |
| Description: | The ERROR light flashes. |
| Causes: | The printhead was replaced with one that is not a genuine Zebra™ printhead. |
| Remedy: | Install a genuine Zebra printhead. |
| Error code: | 02 |
| Display: | ERROR CONDITION RIBBON OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly. |
| Remedy: | Load ribbon correctly. 1. Load ribbon correctly. See Load Ribbon on page 64. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Load media correctly. See Load Media on page 58. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Print a sensor profile. See Print Sensor Profile on page 89. The ribbon out threshold (marked by the word RIBBON) is likely too high, above the black area that indicates where the ribbon is detected. 2. Calibrate the sensors or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. |
| Error code: | 03 |
| Display: | WARNING RIBBON IN |
| Description: | The ERROR light flashes. |
| Causes: | Ribbon is loaded, but the printer is set for direct thermal mode. |
| Remedy: | Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81. |
| Error code: | 04 |
| Display: | ERROR CONDITION PAPER OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded. |
| Remedy: | Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration. |
| Error code: | 05 |
| Display: | ERROR CONDITION HEAD OPEN |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The printhead is not fully closed. The head open sensor is not working properly. |
| Remedy: | Replace the sensor. |
| Error code: | 06 |
| Display: | THERMISTOR FAULT |
| Description: | The ERROR light flashes. |
| Causes: | The printhead has a faulty thermistor. |
| Remedy: | Replace the printhead. |
| Error code: | 07 |
| Display: | WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD |
| Description: | The printer stops; the ERROR light is on; the printer cycles through these three messages. |
| Causes: | The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 08 |
| Display: | WARNING HEAD COLD |
| Description: | The printer prints while the ERROR light flashes. |
| Causes: | The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 09 |
| Display: | WARNING HEAD TOO HOT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The printhead is over temperature. |
| Remedy: | Allow the printer to cool. Printing automatically resumes when the printhead elements cool to an acceptable operating temperature. |
| Error code: | 10 |
| Display: | DEFRAGMENTING |
| Description: | The printer stops. |
| Causes: | The printer is defragmenting memory. |
| Remedy: | Caution • Do NOT turn off the printer power during defragmenting. Doing so can damage the printer. Allow the printer to finish defragmenting. If you get this error message frequently, check your label formats. Formats that write to and erase memory frequently may cause the printer to defragment often. Using properly coded label formats usually minimizes the need for defragmenting. If this error message does not go away, contact Technical Support. The printer requires service. |
| Error code: | 11 |
| Display: | ERROR CONDITION CUTTER JAM |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers. The cutter blade is in the media path. |
| Remedy: | Turn off the printer power and unplug the printer. Inspect the cutter module for debris and clean as needed following the cleaning instructions in Clean the Cutter Module on page 135. |
| Error code: | 12 |
| Description: | General print quality issues |
| Causes: | The printer is set at the incorrect print speed. You are using an incorrect combination of labels and ribbon for your application. The printer is set at an incorrect darkness level. The printhead is dirty. Incorrect or uneven printhead pressure. The printhead is improperly balanced. |
| Remedy: | For optimal print quality, set the print speed to the lowest possible setting for your application via control panel, the driver, or the software. See Adjust Print Speed on page 79. You may want to perform the FEED Self Test on page 120. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. For optimal print quality, set the darkness to the lowest possible setting for your application via the control panel, the driver, or the software. See Adjust Print Darkness on page 78. You may want to perform the FEED Self Test on page 120 to determine the ideal darkness setting. Clean the printhead. See Clean the Printhead and Platen Roller on page 131. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Adjust the printhead balance. |
| Error code: | 13 |
| Description: | Long tracks of missing print on several labels |
| Causes: | Print element damaged. |
| Remedy: | Replace the printhead. |
| Error code: | 14 |
| Description: | Wrinkled ribbon |
| Causes: | Ribbon fed through the machine incorrectly. Incorrect burn temperature. Incorrect or uneven printhead pressure. Media not feeding properly; walking from side to side. The strip plate needs adjusting. The printhead needs vertical adjustment. The printhead is improperly balanced. The printhead and platen roller need to be realigned. |
| Remedy: | See Load Ribbon on page 64. Set the darkness to the lowest possible setting for good print quality. See Adjust Print Darkness on page 78. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Make sure that media is snug by adjusting the media guide, or call a service technician. Adjust the printhead balance. |
| Error code: | 15 |
| Description: | Printing too light or too dark over the entire label |
| Causes: | The media or ribbon is not designed for high-speed operation. You are using an incorrect combination of media and ribbon for your application. You are using ribbon with direct thermal media. Incorrect or uneven printhead pressure. |
| Remedy: | Replace supplies with those recommended for high-speed operation. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. Direct thermal media does not require ribbon. To check if you are using direct thermal media, perform the label scratch test in When to Use Ribbon on page 62. Set the pressure to the minimum needed. See Adjust Printhead Pressure on page 70. |
| Error code: | 16 |
| Description: | Smudge marks on labels |
| Causes: | The media or ribbon is not designed for high-speed operation. |
| Remedy: | Replace supplies with those recommended for high-speed operation. |
| Error code: | 17 |
| Description: | Misregistration/skips labels |
| Causes: | The printer is not calibrated. Improper label format. |
| Remedy: | Recalibrate the printer. Use correct label format. |
| Error code: | 18 |
| Description: | Misregistration and misprint of one to three labels |
| Causes: | The platen roller is dirty. Media does not meet specifications. |
| Remedy: | See Clean the Printhead and Platen Roller on page 131. Use media that meets specifications. |
| Error code: | 19 |
| Description: | Vertical drift in top-of-form position |
| Causes: | The printer is out of calibration. Vertical drift occurs during normal printer operation. Note • A vertical drift of ± 4 to 6 dot rows (approximately 0.5 mm) is within normal tolerances. The platen roller is dirty. |
| Remedy: | Recalibrate the printer. Calibrate the printer. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. |
| Error code: | 20 |
| Description: | Vertical image or label drift |
| Causes: | The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media. |
| Remedy: | Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation. |
| Error code: | 21 |
| Description: | The bar code printed on a label does not scan. |
| Causes: | The bar code is not within specifications because the print is too light or too dark. Not enough blank space around the bar code. |
| Remedy: | Perform the FEED Self Test on page 120. Adjust the darkness or print speed settings as necessary. Leave at least 1/8 in. (3.2 mm) between the bar code and other printed areas on the label and between the bar code and the edge of the label. |
| Error code: | 22 |
| Description: | Loss of printing registration on labels. Excessive vertical drift in top-of-form registration. |
| Causes: | The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly. |
| Remedy: | Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58. |
| Error code: | 23 |
| Description: | Auto Calibrate failed. |
| Causes: | Media or ribbon is loaded incorrectly. The sensors could not detect the media or ribbon. The sensors are dirty or positioned improperly. The sensors are dirty, or media is positioned improperly for the sensors to detect. The media type is set incorrectly. |
| Remedy: | Ensure that media and ribbon are loaded correctly. Manually calibrate the printer. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Ensure that the sensors are clean and that media is positioned properly. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. |
| Error code: | 24 |
| Description: | A label format was sent to the printer but was not recognized. The DATA light does not flash. |
| Causes: | The communication parameters are incorrect. |
| Remedy: | Check the printer driver or software communications settings (if applicable). If you are using serial communication, check the serial port setting in the control panel menu. See Set Serial Communications on page 91. If you are using serial communication, make sure you are using a null modem cable or a null modem adapter. Using the control panel controls, check the protocol setting. It should be set to NONE. See Set Protocol on page 93. If a driver is used, check the driver communication settings for your connection. |
| Error code: | 25 |
| Description: | A label format was sent to the printer. Several labels print, then the printer skips, misplaces, misses, or distorts the image on the label. |
| Causes: | The serial communication settings are incorrect. |
| Remedy: | Ensure that the flow control settings match. Check the communication cable length. See Table 5 on page 48 for requirements. Check the printer driver or software communications settings (if applicable). |
| Error code: | 26 |
| Description: | A label format was sent to the printer but was not recognized. The DATA light flashes but no printing occurs. |
| Causes: | The prefix and delimiter characters set in the printer do not match the ones in the label format. Incorrect data is being sent to the printer. |
| Remedy: | Verify the prefix and delimiter characters. See Set Format Prefix Character on page 94 and Set Delimiter Character on page 95 for the requirements. Check the communication settings on the computer. Ensure that they match the printer settings. If the problem continues, check the label format. |
| Error code: | 27 |
| Description: | Broken or melted ribbon |
| Causes: | Darkness setting too high. |
| Remedy: | 1. Reduce the darkness setting. 2. Clean the printhead thoroughly. |
| Error code: | 28 |
| Description: | The printer does not detect when the ribbon runs out. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly. |
| Causes: | The ribbon-out threshold is set too high to detect the ribbon. On a sensor profile, the ribbon-out threshold (circled in Figure 15) appears above the black bars that indicate the ribbon. This happens if you calibrate the printer without ribbon and later insert ribbon without recalibrating the printer or loading printer defaults. |
| Remedy: | 1. Print a sensor profile (see Print Sensor Profile on page 89), and note the location of the ribbon-out threshold (circled in Figure 15). 2. Calibrate the printer, this time using ribbon, or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. Important • Loading defaults resets all printer parameters back to factory defaults. 3. Print another sensor profile, and compare it to the first one. 4. If the ribbon-out threshold is still too high, you may manually change the value. |
| Error code: | 29 |
| Description: | The ribbon light is on even though ribbon is loaded correctly. |
| Causes: | The printer was not calibrated for the label and ribbon being used. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. |
| Error code: | 30 |
| Description: | The LCD displays a language that I cannot read |
| Causes: | The language parameter was changed through the control panel or a firmware command. |
| Remedy: | 1. Press SETUP/EXIT to enter configuration mode. 2. Press MINUS (-). The printer displays the LANGUAGE parameter in the current language. Even if you cannot recognize the characters displayed, you can still scroll to another language. 3. Press SELECT to select the parameter. 4. Press PLUS (+) or MINUS (-) to scroll through the choices until you find a language that you can read. 5. Press SETUP/EXIT. The LCD displays SAVE CHANGES in the original language. 6. Press SETUP/EXIT again to exit configuration mode and save the changes (if the language does not change, you may need to scroll to a different save option by pressing PLUS (+) or MINUS (-) in the previous step). 7. Repeat this process, if necessary, until you reach the desired language. |
| Error code: | 31 |
| Description: | The LCD is missing characters or parts of characters |
| Causes: | The LCD may need replacing. |
| Remedy: | Run the Power-On Self Test on page 117 and check that the LCD display shows all characters. If not, replace the LCD. |
| Error code: | 32 |
| Description: | Changes in parameter settings did not take effect |
| Causes: | Parameters are set incorrectly. A command turned off the ability to change the parameter. A command changed the parameter back to the previous setting. If the problem continues, there may be a problem with the main logic board. |
| Remedy: | 1. Set parameters and save permanently. 2. Turn the printer off (O) and then on (I). Refer to the ZPL Programming Guide. Refer to the ZPL Programming Guide. Replace the main logic board. |
| Error code: | 33 |
| Description: | The printer fails to calibrate or detect the top of the label. |
| Causes: | The printer was not calibrated for the label being used. The printer is configured for continuous media. The driver or software configuration is not set correctly. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81. Driver or software settings produce commands that can overwrite the printer configuration. Check the driver or software media-related setting. |
| Error code: | 34 |
| Description: | Non-continuous labels are being treated as continuous labels. |
| Causes: | The printer was not calibrated for the media being used. The printer is configured for continuous media. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81. |
| Error code: | 35 |
| Description: | All lights are on, but nothing displays on the LCD, and the printer locks up. |
| Causes: | Internal electronic or firmware failure. |
| Remedy: | Turn the printer power off (O) and then on (I). If the printer locks up again, replace the main logic board. |
| Error code: | 36 |
| Description: | The printer locks up while running the Power-On Self Test. |
| Causes: | Main logic board failure. |
| Remedy: | Replace the main logic board. |
| Error code: | 37 |
| Description: | Non-continuous labels are being treated as continuous labels. |
| Causes: | The printer is configured for continuous media. The printer was not calibrated for the media being used. |
| Remedy: | Set the media type to noncontinuous media. See Set Media Type on page 56. Perform the calibration procedure in Calibrate Media and Ribbon Sensors on page 67. |
| Error code: | 38 |
| Description: | All lights are on, but nothing displays on the LCD, and the printer locks up. |
| Causes: | Internal electronic or firmware failure. |
| Remedy: | Turn the printer power Off (O) and then On (I). If the printer locks up again, replace the main logic board. |
| Error code: | 39 |
| Description: | The printer locks up while running the Power-On Self Test. |
| Causes: | Main logic board failure. |
| Remedy: | Replace the main logic board. |
| Error code: | 40 |
| Display: | Scanner locked |
| Description: | 10-348 ERROR 40 FUSER MAIN LAMP FAILURE Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault, Clear <10-348 & 10-350> is run. |
| Causes: | 1. Deformed paper sensor actuator or faulty sensor. 2. SMPS PBA or Main PBA is defective 3. Faulty cables or connectors. |
| Remedy: | Switch printer power OFF. Remove the Fuser Assembly. Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Replace the Engine Control Board. |
| Error code: | 41 |
| Display: | Self Diagnostic LSU |
| Description: | Install or Reseat Fuser, Code 41 Front thermistor open error. This is a cold condition. Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault is performed. |
| Causes: | • Fuser • Engine Control Board |
| Remedy: | 1 1. Turn OFF power and remove the Fuser Assembly. 2. Measure the resistance between the fuser connector P600-4 and P600-6. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Replace the engine control board. Go to step 3. 3 1. Turn OFF printer power. 2. Check for an open circuit or poor connection between J600-4 to J600-6 to J404A-2. 3. Is the wiring OK? Replace the engine control board. Repair or replace the wiring harness. |
| Error code: | 42 |
| Display: | Self Diagnostic Temperature |
| Description: | 10-352 ERROR 42 FUSER STS (FRONT) WARM TIME FAILURE |
| Causes: | 1. The ‘Open Cover’ microswitch may be stuck or faulty 2. The tab on the front cover may be damaged or broken 3. Check the connector and cables between Switch and main PBA. |
| Remedy: | Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board. |
| Error code: | 43 |
| Display: | Send Error (AUTH) |
| Description: | 10-353 ERROR 43 FUSER SSR1 ON TIME FAILURE |
| Causes: | 1. The ‘Open Cover’ microswitch may be stuck or faulty 2. Check the connector and cables between Switch and main PBA. |
| Remedy: | Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board. |
| Error code: | 44 |
| Display: | Send Error (DNS) |
| Description: | Fuser Sub Lamp Overheat Failure, Code 44 The front thermistor has detected an overheat condition. Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault is performed. |
| Causes: | • Fuser • Engine Control Board |
| Remedy: | 1 1. Turn OFF power, remove the fuser assembly and allow it to cool down. 2. Measure the resistance between the Fuser connector P600-7 and P600-9. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Go to step 4. Go to step 3. 3 1. Turn OFF printer power. 2. Measure the resistance between J641-4 and J641-5 on the engine control board. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 4. Repair or replace the wiring harness. 4 1. Turn printer power back ON. 2. Is there ~+3.4 VDC between J590-3 and ground? Check the AC wiring harness to the fuser. If the check is OK, replace the AC drive assembly. Replace the engine control board. |
| Error code: | 45 |
| Display: | Send Error (POP3) |
| Description: | Fuser STS (Rear) Failure, Code 45 Rear Thermistor open error. The machine logic detected an open circuit in the rear thermistor. |
| Causes: | • Fuser • Engine Control Board |
| Remedy: | 1 1. Turn OFF power, remove the fuser assembly and allow it to cool down. 2. Measure the resistance between the Fuser connector P600-7 and P600-9. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Replace the engine control board. Go to step 3. 3 1. Turn printer power OFF. 2. Check for an open circuit or poor connection between J641-4 and J641-5. 3. Is the wiring harness OK? Replace the engine control board. Repair or replace the wiring harness. |
| Error code: | 46 |
| Display: | Send Error (SMTP) |
| Description: | 10-354 ERROR 46 FUSER STS (REAR) WARM TIME FAILURE |
| Causes: | 1. Check stability of 24V supply to LSU. |
| Remedy: | Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-7 and P600-9. Does the resistance measure between 20 ohms and 100 ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-3 and P404A-4 on the Engine Control Board. Does the resistance measure between 20K ohms and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board. |
| Error code: | 47 |
| Display: | Send Error (Wrong Config) |
| Description: | 10-356 ERROR 47 FUSER SSR2 ON TIME FAILURE |
| Causes: | There is disconnection in the paper transfer bias supply circuit. (Dirty or deformed electrodes) |
| Remedy: | Measure the resistance between the Fuser Assembly connector P600-1 and P600-3. Does the resistance measure approximately 6 ohms for a 110 VAC Fuser or approximately 20 ohms for a 220 VAC Fuser? Y↓N→ Replace the Fuser Assembly. Measure the resistance between the Fuser Assembly connector P600-7 and P600-9. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-3 and P404A-4 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Reinstall the Fuser. Switch printer power ON. Does the Fuser get warm? Y↓N→ Replace the Chassis AC Power Assembly. Replace the Engine Control Board. |
| Error code: | 48 |
| Display: | [Stop Pressed] |
| Description: | Fan Failure, Code 48 The machine logic detected a failure of the Fuser fan, LVPS fan, or rear fan. |
| Causes: | • Fuser Fan • LVPS Fan • Rear Fan |
| Remedy: | 1 1. Enter service diagnostics and run the fan test. 2. Does the fuser fan rotate at a high speed? Go to step 4. Go to step 2. 2 1. Check for voltage at J222-4. 2. Does the voltage measure +24 VDC? Go to step 3. Check the wiring to the fuser fan, if the wiring is OK, replace the engine control board. 3 Does the front panel indicate the fans are ON? Replace the fan. Check the wiring to the fuser fan, if the wiring is OK, replace the engine control board. 4 Does the rear fan revolve at high speed? Go to step 7. Go to step 5. 5 1. Check for voltage at J552-1. 2. Does the voltage measure +24 VDC? Go to step 6. Check the wiring to the rear fan, if the wiring is OK replace the interface board. If the problem continues, replace the engine control board. 6 Does the front panel indicate the fans are ON? Replace the rear fan. Check the wiring tot he rear fan, if the wiring is OK, replace the engine control board. 7 Does the LVPS fan revolve at high speed? The fans are operating correctly. If the problem persists, replace the engine control board. Go to step 8. 8 1. Check for voltage at J214-4. 2. Is +24 VDC present? Go to step 9. Check the wiring to the LVPS fan, if the wiring is OK, replace the engine control board. 9 Does the front panel indicate the fans are ON? Replace the LVPS assembly. Check the wiring to the LVPS fan, if the wiring is OK, replace the engine control board. |
| Error code: | 49 |
| Display: | Tray 1 Paper Empty |
| Description: | There is no paper in the tray 1. |
| Causes: | Pressure roller thermistor, pressure roller lamp connector, MCU |
| Remedy: | Load paper in the tray 1. |
| Error code: | 50 |
| Display: | Tray 2 Paper Empty |
| Description: | Fuser Fan Failure The Fuser Fan rotation signal indicates to the Engine Control Board that the fan is no longer operational. |
| Causes: | • Fuser Fan, PL5.3.31 • FAN/PHD/MOT Harness, PL10.1.9 • Engine Control Board, PL9.1.16 |
| Remedy: | 1 Check the Fuser Fan for damage. Remove the Front Cover. Is the fan damaged? Replace the Fuser Fan. Go to Step 2. 2 Check the Fuser Fan connection. Is P/J482 connected to the harness? Go to Step 2. Reconnect the Fan. 3 Check orientation of the Fuser Fan. Does the Fan’s label face into the chute? Go to Step 3. Correct the installation. 4 Test the Fuser Fan. Run the Service Diagnostics Fuser Fan test. Does the Fan operate. Go to Step 6. Go to Step 5. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J482. 2. Check continuity between J48 <=> P483. Go to Step 5. Replace the FAN/PHD/MOT Harness. 6 Check the fan rotation signal. Print one sheet. Is there +3.3 V across P/J48-A12 <=> P/J48-A13? Replace the Engine Control Board. Replace the Fuser Fan. |
| Error code: | 51 |
| Display: | Send Error (DNS) |
| Description: | Rear Fan Failure The Rear Fan rotation signal indicates the fan is no longer operational. |
| Causes: | • Rear Fan, PL1.1.19 • LVPS, PL9.1.6 • Engine Control Board, PL9.1.16 • LV Harness, PL10.1.2 |
| Remedy: | 1 Check the Rear Fan for damage. Remove the Rear Cover. Is the fan damaged? Replace the Rear Fan. Go to Step 2. 2 Check the Rear Fan connection. Is P/J166 connected to the harness? Go to Step 3. Connect the Fan. 3 Check orientation of the Rear Fan. Does the Fan’s label face inwards? Go to Step 4. Correct the installation. 4 Test the Rear Fan. Run the Service Diagnostics Rear Fan test. Does the fan operate? Go to Step 6. Go to Step 5. 5 Check for +24 V to the fan. Disconnect P/J166. Is there +24 V across P166-1 <=> P166-3? Replace the Rear Fan. Replace the LVPS. 6 Check the fan rotation signal to the LVPS. Print one sheet. Is there +3.3 V between P/J166-1 <=> P/J166-3? Replace the Fuser Fan. Go to Step 7. 7 Check the rotation signal from the LVPS. Print one sheet. Is there +3.3 V between P/J165-15 <=> P/J165-3? Replace the LVPS. Go to Step 8. 8 Check the fan rotation signal at the Engine Control Board. Print one sheet. Is there +3.3 V between P/J61-4 <=> P/J61-16? Replace the LV Harness Replace the Engine Control Board. |
| Error code: | 52 |
| Display: | Send Error (POP3) |
| Description: | Fan Failure One of the two fans has failed resulting in a fatal error. |
| Causes: | • Rear Fan, PL1.1.19 • Fuser Fan, PL5.3.31 |
| Remedy: | 1 Check the fans for damage or debris: • Fuser Fan, PL1.1.19 • Rear Fan, PL5.3.31 Is either fan damaged? Replace the defective fan. Go to Step 3. 2 Replace the defective fan. Does the error persist? Go to Step 3 Complete 3 Test the fans. Run the Service Diagnostics fan tests to isolate the defective fan. Did one of the fans fail? Go to the troubleshooting procedure for the specific fan. If both fans pass, replace the Engine Control Board. |
| Error code: | 53 |
| Display: | Send Error (SMTP) |
| Description: | The password did not match in a relay or mailbox transmission, and the transmission ended in failure. |
| Causes: | · Loose cable connection · Defective controller fan · Defective IOD1 board · Defective MCTL board |
| Remedy: | Confirm that both parties are using the same system password and the both units are compatible. Then, ask the remote party to transmit again. |
| Error code: | 54 |
| Display: | Send Error (Wrong Config) |
| Description: | 10-398 ERROR 54 FAN FAILURE |
| Causes: | · Loose cable connection · Defective ozone fan · Defective IOD2 board · Defective MCTL board |
| Remedy: | Enter Service Diagnostics Mode. Run the “Fuser Fan” test. Does the Fuser Fan operate? Y↓N→ Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-1 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-4 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-3 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the Fuser Fan. Replace the Fuser Fan Assembly. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-5 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-8 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-7 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the +24 VDC LVPS Fan. Replace the +24 VDC LVPS Fan. |
| Error code: | 55 |
| Display: | [Stop Pressed] |
| Description: | Stop/Clear has been pressed during a fax transmission. |
| Causes: | · Loose cable connection · Defective fusing unit fan · Defective IOD1 board · Defective MCTL board |
| Remedy: | Try again. |
| Error code: | 56 |
| Display: | Toner Empty |
| Description: | The toner cartridge has run out. The machine stops printing. |
| Causes: | Harness connection failure of back cover switch ASSY. Eject actuator failure. Eject sensor PCB ASSY failure. Main PCB failure |
| Remedy: | Replace the toner cartridge with a new one. |
| Error code: | 57 |
| Display: | Toner Low |
| Description: | The toner cartridge is almost empty. |
| Remedy: | Take out the toner cartridge and thoroughly shake it. By doing this, you can temporarily reestablish printing operations. |
| Error code: | 58 |
| Display: | Tray 1 Paper Empty |
| Description: | There is no paper in the tray 1. |
| Causes: | Harness connection failure between fuser unit and eject sensor PCB. Fuser unit failure. LVPS PCB failure. Eject sensor PCB ASSY failure. Main PCB failure |
| Remedy: | Load paper in the tray 1. |
Название
Samsung Тонер-картридж голубой (2000 стр.)
Samsung Тонер-картридж голубой (5000 стр.)
Samsung Тонер-картридж черный (2500 стр.)
Samsung Тонер-картридж черный (5500 стр.)
Samsung Тонер-картридж пурпурный (2000 стр.)
Samsung Тонер-картридж пурпурный (5000 стр.)
Samsung Узел ремня переноса в сборе
Samsung Тонер-картридж желтый (2000 стр.)
Samsung Тонер-картридж желтый (5000 стр.)
