Samsung ML-2570

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Скорость печати A4

Цветность печати

черно-белая

Общие характеристики
Тип	лазерный/светодиодный
Цветность печати
Технология печати	лазерная
Тип устройства	Принтер
Размещение	настольный
Макс. формат	A4
Печать фотографий
Телефон
Сканер
Копир
Факс
Принтер
Двусторонняя печать
Печать без полей
Прямая печать
Макс, разрешение для ч/б печати
По Y	1 200
По X	1 200
Скорость ч/б печати
A4	24
Время выхода первого отпечатка
Ч/б	9
Расходные материалы
Количество картриджей	1
Ресурс ч/б картриджа/тонера	3 000
Печать на:
Фотобумаге
Рулоне
CD/DVD
Конвертах
Матовой бумаге
Пленках
Глянцевой бумаге
Этикетках
Карточках
Телефон
Проводная трубка
Спикерфон
Стандарт DECT
Беспроводная трубка
АОН
Caller ID
Автоответчик
Языки управления
PostScript 3
PostScript
PCL 6
PostScript 2
PCL 5e
PPDS
PDF
PCL 5c
Лотки
Подача бумаги
Стандартная	250
Вывод бумаги
Стандартный	100
Финишер
Брошюровщик
Электронная сортировка
Сортировка со сдвигом
Степлер
Сортер
Интерфейсы
Версия USB	2,0
LPT
USB
FireWire (IEEE 1394)
Ethernet (RJ-45)
Устройство для чтения карт памяти
Веб-интерфейс
RS-232
Инфракрасный порт
Bluetooth
Wi-Fi
Память/Процессор
Объем памяти	32
Макс, объем памяти	32
Процессор	Samsung
Частота процессора	400
Дополнительная информация
Мин. системные требования
Поддержка ОС
Windows
Linux
Mac OS
DOS
Уровень шума
В режиме ожидания	35
При работе	53
Габариты
Вес	5,6
Ширина	354
Высота	246
Глубина	297

Коды ошибок

00 ... 05

20, 21, 22

60, 62, 68

Описание

Парткод

ML-2010D3

MLT-D119S

Название

Samsung Тонер-картридж черный

Samsung 119 Тонер-картридж черный

Error code:	00 ... 05
Display:	Ready(kind of paper)
Description:	The printer is ready, the paper is detected when the first paper is printed. 00: Legal ,01: Letter ,02: A4 ,03: EXEC ,04: B5 ,05: Folio, 06: A5/A6

Error code:	20, 21, 22
Display:	Print Start
Description:	The engine controller received the print order from the video controller. 20: 1st, 21: MP, 22: SCF

Error code:	30
Description:	The LCD displays a language that I cannot read
Causes:	The language parameter was changed through the control panel or a firmware command.
Remedy:	1. Press SETUP/EXIT to enter configuration mode. 2. Press MINUS (-). The printer displays the LANGUAGE parameter in the current language. Even if you cannot recognize the characters displayed, you can still scroll to another language. 3. Press SELECT to select the parameter. 4. Press PLUS (+) or MINUS (-) to scroll through the choices until you find a language that you can read. 5. Press SETUP/EXIT. The LCD displays SAVE CHANGES in the original language. 6. Press SETUP/EXIT again to exit configuration mode and save the changes (if the language does not change, you may need to scroll to a different save option by pressing PLUS (+) or MINUS (-) in the previous step). 7. Repeat this process, if necessary, until you reach the desired language.

Error code:	40
Display:	Scanner locked
Description:	10-348 ERROR 40 FUSER MAIN LAMP FAILURE Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault, Clear <10-348 & 10-350> is run.
Causes:	1. Deformed paper sensor actuator or faulty sensor. 2. SMPS PBA or Main PBA is defective 3. Faulty cables or connectors.
Remedy:	Switch printer power OFF. Remove the Fuser Assembly. Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Replace the Engine Control Board.

Error code:	50
Display:	Tray 2 Paper Empty
Description:	Fuser Fan Failure The Fuser Fan rotation signal indicates to the Engine Control Board that the fan is no longer operational.
Causes:	• Fuser Fan, PL5.3.31 • FAN/PHD/MOT Harness, PL10.1.9 • Engine Control Board, PL9.1.16
Remedy:	1 Check the Fuser Fan for damage. Remove the Front Cover. Is the fan damaged? Replace the Fuser Fan. Go to Step 2. 2 Check the Fuser Fan connection. Is P/J482 connected to the harness? Go to Step 2. Reconnect the Fan. 3 Check orientation of the Fuser Fan. Does the Fan’s label face into the chute? Go to Step 3. Correct the installation. 4 Test the Fuser Fan. Run the Service Diagnostics Fuser Fan test. Does the Fan operate. Go to Step 6. Go to Step 5. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J482. 2. Check continuity between J48 <=> P483. Go to Step 5. Replace the FAN/PHD/MOT Harness. 6 Check the fan rotation signal. Print one sheet. Is there +3.3 V across P/J48-A12 <=> P/J48-A13? Replace the Engine Control Board. Replace the Fuser Fan.

Error code:	61
Display:	Nongenuine Toner Replace Toner 1
Description:	The toner cartridge installed is not a genuine cartridge.
Causes:	The printer warms up when the printer is turned on or the cover is closed, or wake from sleep mode.
Remedy:	This message appears when you selected stop at the Non Genuine Toner prompt. Install the genuine toner cartridge.

Error code:	64
Display:	Toner Exhausted Replace Toner 1
Description:	Cover Open
Causes:	The Printer Cover is open or Toner Cartridge not installed.

Error code:	65
Display:	Toner Exhausted Replace Toner
Description:	The life span of the toner cartridge is reached.
Causes:	· Loose cable connection · Defective development solenoid – replace the front cover unit · Defective IOD2 board · Defective MCTL board
Remedy:	This message appears when you selected continue at the Toner Exhausted prompt. Install the genuine toner cartridge.

Error code:	69
Display:	Sleep Mode
Description:	Sleep Mode
Causes:	It means that the printer fuser is turned off, and the power consumption is minimized.
Remedy:	1) Check the harness connected between the Engine controller and the paper size board. (If the harness is out, insert it to the connector.) 2) In the Engine diagnostic mode, operate the MPF trans sensor to check if it is operating. (If it is not operating, replace the paper size board.) 3) Replace the MPF transfer.

Error code:	70
Display:	No Paper
Description:	No Paper
Causes:	No paper in the paper cassette.

Error code:	71
Display:	Paper Jam 0
Description:	Paper Jam 0
Causes:	The front part of paper is jammed between pickup unit and Feed sensor.

Error code:	72
Display:	Paper Jam 1
Description:	Engine Firmware Failure The Engine Control Board detected a firmware error.
Causes:	• Engine Control Board, Pl9.1.16 • EEPROM Board, PL9.1.12
Remedy:	1 Cycle printer power. Does the error persist? Go to Step 2. Complete 2 Is P/J144 on the EEPROM Board properly seated and defect free? Go to Step 3. Reseat P/J144 or replace the EEPROM Board. 3 Turn printer power off and then back on. Does the error persist? Replace the Engine Control Board. Complete

Error code:	73
Display:	Paper Jam 2
Description:	Paper Jam 2
Causes:	The front part of paper is jammed just after passing through the discharge sensor.

Error code:	76
Display:	Out Bin Full
Description:	Fuser Firmware Failure A failure was detected in the Fuser Firmware.
Causes:	• Fuser, PL5.1.1 • FSR/ADC Harness, PL5.2.28 • Engine Control Board, PL9.1.16
Remedy:	1 Check the Fuser for damage. Is the Fuser damaged? Replace the Fuser. Go to Step 2. 2 Check the Fuser connection for damage. Any broken or bent pins? Repair or replace the parts. Go to Step 3. 3 Replace the Fuser. Does the error persist? Go to Step 4. Complete 4 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J361. 2. Check continuity between J36 <=> J361. Replace the Engine Control Board. Replace the FSR/ ADC Harness.

Error code:	95
Display:	LSU Not Ready
Description:	Non-Xerox Imaging Unit A Imaging Unit CRUM I.D. error indicates that a non-Xerox Imaging Unit is installed.
Causes:	• Imaging Unit, PL6.1.1 • CRUM Board, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Imaging Unit part number. Is the Imaging Unit a genuine Xerox Phaser 6300/6350 part? Go to Step 2. Replace the Imaging Unit. 2 Check the Imaging Unit for damage. Is the Imaging Unit damaged? Replace the Imaging Unit. Go to Step 4. 3 Replace the Imaging Unit. Does the error persist? Go to Step 5. Complete 4 Check the CRUM connection. Is P/J710 connected to the harness? Go to Step 3. Connect the CRUM 5 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J710 <=> J484. Go to Step 4. Replace the PHD2 Harness. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J484. 2. Check continuity between J48<=>P484. Go to Step 5. Replace the FAN/ PHD/MOT Harness. 7 Replace the Imaging Unit. Does the error persist? Replace the Engine Control Board. Complete

Samsung ML-2570

Общие характеристики

Тип

Цветность печати

Технология печати

Тип устройства

Размещение

Макс. формат

Печать фотографий

Телефон

Сканер

Копир

Факс

Принтер

Двусторонняя печать

Печать без полей

Прямая печать

Макс, разрешение для ч/б печати

Скорость ч/б печати

Время выхода первого отпечатка

Расходные материалы

Количество картриджей

Ресурс ч/б картриджа/тонера

Печать на:

Телефон

Проводная трубка

Спикерфон

Стандарт DECT

Беспроводная трубка

АОН

Caller ID

Автоответчик

Языки управления

Лотки

Подача бумаги

Вывод бумаги

Финишер

Брошюровщик

Электронная сортировка

Сортировка со сдвигом

Степлер

Сортер

Интерфейсы

Версия USB

LPT

USB

FireWire (IEEE 1394)

Ethernet (RJ-45)

Устройство для чтения карт памяти

Веб-интерфейс

RS-232

Инфракрасный порт

Bluetooth

Wi-Fi

Память/Процессор

Объем памяти

Макс, объем памяти

Процессор

Частота процессора

Дополнительная информация

Мин. системные требования

Поддержка ОС

Уровень шума

Габариты

Вес

Ширина

Высота

Глубина

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку