Samsung ML-5200A
Рейтинг
Модули
Top Cover Exploded View
Feeder (1/2) Exploded View
Fuser Exploded View
Motor Exploded View
PCB Exploded View
Front Cover Exploded View
Feeder (2/2) Exploded View
Frame Exploded View
Main Exploded View
Детали PCB Exploded View
| Деталь: | MEA-UNITTRAY |
| Парткод: | JC97-01135C |
| Деталь: | MEA Unit-Cover Rear |
| Парткод: | JC97-01154B |
| Деталь: | MEA UNIT-SEPARATE |
| Парткод: | JC97-01132A |
| Деталь: | SPRING-KNOCK UP |
| Парткод: | JC61-70934A |
| Деталь: | HOLDER K/SPRING ASSY |
| Парткод: | JC97-01169A |
| Деталь: | SPRING-SEPARATE |
| Парткод: | JC61-70935A |
| Деталь: | SPRING-EXTENSION |
| Парткод: | JC61-70950A |
| Деталь: | MEA UNIT-KNOCK UP |
| Парткод: | JC97-01127A |
| Деталь: | MEA UNIT-CLUTCH |
| Парткод: | JC97-01129A |
| Деталь: | MEA UNIT-PICK UP |
| Парткод: | JC97-01130A |
| Деталь: | BUSHING SHAFT LOCK |
| Парткод: | JG72-40849A |
| Деталь: | HOLDER SPRING K-UP |
| Парткод: | JC72-41153A |
| Деталь: | GROUND K-UP |
| Парткод: | JC70-11016A |
| Деталь: | ELA-UNIT FUSER |
| Парткод: | JC96-00971F |
| Деталь: | ELA-UNIT FUSER |
| Парткод: | JC96-00971H |
| Деталь: | REDRIVE |
| Парткод: | JC97-01223A |
| Деталь: | MEA ETC-HOLDER P/R |
| Парткод: | JC97-01204A |
| Деталь: | Roller-Pressure |
| Парткод: | JC75-10981A |
| Деталь: | MEA ETC-ROLLER EXIT |
| Парткод: | JC97-01126A |
| Деталь: | BEARING-EXIT |
| Парткод: | JC75-10968A |
| Деталь: | UNIT EXIT F/DOWN |
| Парткод: | JC66-10200A |
| Деталь: | GEAR-EXIT(18) |
| Парткод: | JC66-40956A |
| Деталь: | THERMOSTAT |
| Парткод: | 4712-000001 |
| Деталь: | GEAR-IDLE2(Z19) |
| Парткод: | JC66-40945A |
| Деталь: | GEAR-IDLE3(Z14) |
| Парткод: | JC66-40946A |
| Деталь: | GROUND-PLATE,FU |
| Парткод: | JC70-11003A |
| Деталь: | LAMP-HALOGEN |
| Парткод: | 4713-001080 |
| Деталь: | LAMP-HALOGEN |
| Парткод: | 4713-001081 |
| Деталь: | GEAR-FUSER |
| Парткод: | JC66-40379A |
| Деталь: | BEARING-H/R,L |
| Парткод: | JC66-10203A |
| Деталь: | HEAT-ROLLER |
| Парткод: | JC71-20903A |
| Деталь: | ROLLER-EXIT,F/UP |
| Парткод: | JC72-20901A |
| Деталь: | BEARING-H/R,R |
| Парткод: | JC66-10207A |
| Деталь: | ROLLER-F/UP(2) |
| Парткод: | JC72-20902A |
| Цена: | 500 ₽ |
| Деталь: | SHAFT-IDLE, F/UP |
| Парткод: | JC70-20901A |
| Деталь: | Guide-Claw |
| Парткод: | JC72-41128A |
| Деталь: | THERMISTOR |
| Парткод: | 1404-001128 |
| Деталь: | SPRING-EXIT,F/UP |
| Парткод: | JC61-70936A |
| Деталь: | Spring-ES |
| Парткод: | JC61-70962A |
| Деталь: | SPRING-EXIT,F/DOWN |
| Парткод: | JC61-70937A |
| Деталь: | SPRING-IDLE FU |
| Парткод: | JC70-11066A |
| Деталь: | ELA-UNIT MOTOR |
| Парткод: | JC96-01200A |
| Деталь: | PBA SUB-HVPS |
| Парткод: | JC92-01002A |
| Деталь: | ENGINE TO HVPS |
| Парткод: | JC39-40558A |
| Деталь: | JOINT-B/D |
| Парткод: | JC92-01001A |
| Деталь: | FUSE(V2) 250VAC T5A |
| Парткод: | 3601-000002 |
| Деталь: | FUSE |
| Парткод: | 3601-000157 |
| Деталь: | ENGINE TO JOINT |
| Парткод: | JC39-40564A |
| Деталь: | PBA MAIN-ENGINE |
| Парткод: | JC96-00974A |
| Деталь: | PBA MAIN-ENGINE |
| Парткод: | JC96-00973A |
| Деталь: | CONTROLLER |
| Парткод: | JC96-00975A |
| Деталь: | SIMM ACCESS |
| Парткод: | JC70-11015A |
| Деталь: | OPERATOR PANEL |
| Парткод: | JC39-40579A |
| Деталь: | ENGINE TO CONTROLLER |
| Парткод: | JC39-40548A |
| Деталь: | STACKER(RX) |
| Парткод: | JC72-41270A |
| Деталь: | STACKER-EXTEND |
| Парткод: | JC72-41278A |
| Деталь: | Cover-Stacker |
| Парткод: | JC72-41267A |
| Деталь: | FRAME-STACKER |
| Парткод: | JC72-41268A |
| Деталь: | STOPPER |
| Парткод: | JC72-41170A |
| Деталь: | Cover-Front |
| Парткод: | JC72-00022A |
| Деталь: | DUCT |
| Парткод: | JC97-01219B |
| Деталь: | GUIDE-STACKER |
| Парткод: | JC72-41269A |
| Деталь: | COVER-EXIT |
| Парткод: | JC72-41276A |
| Деталь: | LED |
| Парткод: | JC72-41263A |
| Деталь: | KEY |
| Парткод: | JC72-41262A |
| Деталь: | PBA-PANEL |
| Парткод: | JC92-01059A |
| Деталь: | COVER-PCB |
| Парткод: | JC72-41275A |
| Деталь: | ASSY-COVER FRONT |
| Парткод: | JC96-00981A |
| Деталь: | MEA UNIT-FRAME SUP |
| Парткод: | JC97-01128A |
| Деталь: | MEA-UNIT GEAR FEED |
| Парткод: | JC97-01131A |
| Деталь: | ACTUATOR EMPTY |
| Парткод: | JC72-41151A |
| Деталь: | SEPARATE PAPER |
| Парткод: | JC72-41155A |
| Деталь: | ASSY-P.EMPTY |
| Парткод: | JC92-01044A |
| Деталь: | PRINTHEAD TO HVPS |
| Парткод: | JC39-40566A |
| Деталь: | UNIT-LSU |
| Парткод: | JC59-10505A |
| Деталь: | COVER OPEN SENSOR |
| Парткод: | JC92-01081A |
| Деталь: | SPRING-C/O |
| Парткод: | JC61-70931A |
| Деталь: | ACTUATOR-C/O |
| Парткод: | JC72-41134A |
| Деталь: | COVER-C/O |
| Парткод: | JC72-41139A |
| Деталь: | FRAME BASE UPPER |
| Парткод: | JC72-41141A |
| Деталь: | CAP PLATE,G/DEVE L |
| Парткод: | JC72-41173A |
| Деталь: | SPRING-G/DEVE |
| Парткод: | JC61-70932A |
| Деталь: | CAP PLATE,G/DEVE R |
| Парткод: | JC72-41135A |
| Деталь: | SOLENOID |
| Парткод: | JC33-10004A |
| Деталь: | Roller-Transfer |
| Парткод: | JC75-10963A |
| Деталь: | MEA UNIT-HOLDER TR R |
| Парткод: | JC97-01112A |
| Деталь: | MEA-UNIT SEPARATE(L) |
| Парткод: | JC97-01133A |
| Деталь: | MEA-UNIT SEPARATE(R) |
| Парткод: | JC97-01134A |
| Деталь: | MEA-UNIT FRAME LOWER |
| Парткод: | JC97-01123A |
| Деталь: | CBF-HARNESS,3P,BLK |
| Парткод: | JC39-40550A |
| Деталь: | CBF-HARNESS,3PWHT |
| Парткод: | JC39-40581A |
| Деталь: | ASSY-FEED SENSOR |
| Парткод: | JC92-01017A |
| Деталь: | Actuator-Exit |
| Парткод: | JC72-41130A |
| Деталь: | COVER WIRE FU |
| Парткод: | JC72-41138A |
| Деталь: | MEA UNIT-TERMINAL TR |
| Парткод: | JC97-01113A |
| Деталь: | MEA UNIT-TERMINAL L |
| Парткод: | JC97-01114A |
| Деталь: | ELA UNIT FUSE DEVE |
| Парткод: | JC96-01117A |
| Деталь: | POWER SWITCH |
| Парткод: | JC39-40585A |
| Деталь: | PICK ROLLER ACCESS |
| Парткод: | JC72-41244A |
| Деталь: | ELA UNIT-PTL |
| Парткод: | JC96-01190A |
| Деталь: | MEA UNIT-HOLDER TR L |
| Парткод: | JC97-01160A |
| Деталь: | HOLDER SPRING |
| Парткод: | JC72-41156A |
| Деталь: | GUIDE BOSS DEVE |
| Парткод: | JC72-41243A |
| Деталь: | RUBBER FOOT |
| Парткод: | JC73-10926A |
| Деталь: | COVER TOP |
| Парткод: | JC72-41279A |
| Деталь: | COVER SIDE,L |
| Парткод: | JC72-41086C |
| Деталь: | DC FAN MOTOR |
| Парткод: | JC31-30502A |
| Деталь: | COVER SIDE,R |
| Парткод: | JC72-41087C |
| Деталь: | Cover-Bottom |
| Парткод: | JC72-41089C |
Коды ошибок
00 ... 04
20
30
40
50
60, 62, 68
61
64
69
70
71
72
73
95
Описание
| Error code: | 00 ... 04 |
| Description: | Ready(paper type) |
| Causes: | The printer is in printable state. The paper type is sensed after one page printing. |
| Error code: | 20 |
| Description: | Vertical image or label drift |
| Causes: | The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media. |
| Remedy: | Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation. |
| Error code: | 30 |
| Description: | The LCD displays a language that I cannot read |
| Causes: | The language parameter was changed through the control panel or a firmware command. |
| Remedy: | 1. Press SETUP/EXIT to enter configuration mode. 2. Press MINUS (-). The printer displays the LANGUAGE parameter in the current language. Even if you cannot recognize the characters displayed, you can still scroll to another language. 3. Press SELECT to select the parameter. 4. Press PLUS (+) or MINUS (-) to scroll through the choices until you find a language that you can read. 5. Press SETUP/EXIT. The LCD displays SAVE CHANGES in the original language. 6. Press SETUP/EXIT again to exit configuration mode and save the changes (if the language does not change, you may need to scroll to a different save option by pressing PLUS (+) or MINUS (-) in the previous step). 7. Repeat this process, if necessary, until you reach the desired language. |
| Error code: | 40 |
| Display: | Scanner locked |
| Description: | 10-348 ERROR 40 FUSER MAIN LAMP FAILURE Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault, Clear <10-348 & 10-350> is run. |
| Causes: | 1. Deformed paper sensor actuator or faulty sensor. 2. SMPS PBA or Main PBA is defective 3. Faulty cables or connectors. |
| Remedy: | Switch printer power OFF. Remove the Fuser Assembly. Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Replace the Engine Control Board. |
| Error code: | 50 |
| Display: | Tray 2 Paper Empty |
| Description: | Fuser Fan Failure The Fuser Fan rotation signal indicates to the Engine Control Board that the fan is no longer operational. |
| Causes: | • Fuser Fan, PL5.3.31 • FAN/PHD/MOT Harness, PL10.1.9 • Engine Control Board, PL9.1.16 |
| Remedy: | 1 Check the Fuser Fan for damage. Remove the Front Cover. Is the fan damaged? Replace the Fuser Fan. Go to Step 2. 2 Check the Fuser Fan connection. Is P/J482 connected to the harness? Go to Step 2. Reconnect the Fan. 3 Check orientation of the Fuser Fan. Does the Fan’s label face into the chute? Go to Step 3. Correct the installation. 4 Test the Fuser Fan. Run the Service Diagnostics Fuser Fan test. Does the Fan operate. Go to Step 6. Go to Step 5. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J482. 2. Check continuity between J48 <=> P483. Go to Step 5. Replace the FAN/PHD/MOT Harness. 6 Check the fan rotation signal. Print one sheet. Is there +3.3 V across P/J48-A12 <=> P/J48-A13? Replace the Engine Control Board. Replace the Fuser Fan. |
| Error code: | 60, 62, 68 |
| Display: | Fuser Error |
| Description: | Fuser Error |
| Causes: | The error in the fuser occurred. There is a short circuit in the thermistor and the thermostat while printing, Low Temperature Error occurs. • 60: Open Fuser Error • 62: Low Heat Error • 68: Over Heat Error |
| Remedy: | 1. If the thermostat is open replace the fuser and check following items. 2. If the thermistor sensor device is located deep in the sponge, replace the fuser. 3. Check if the circuit of overheat mode works properly. 4. Run DCU mode : Perform DCU diagnostic code 10. |
| Error code: | 61 |
| Display: | Nongenuine Toner Replace Toner 1 |
| Description: | The toner cartridge installed is not a genuine cartridge. |
| Causes: | The printer warms up when the printer is turned on or the cover is closed, or wake from sleep mode. |
| Remedy: | This message appears when you selected stop at the Non Genuine Toner prompt. Install the genuine toner cartridge. |
| Error code: | 64 |
| Display: | Toner Exhausted Replace Toner 1 |
| Description: | Cover Open |
| Causes: | The Printer Cover is open or Toner Cartridge not installed. |
| Error code: | 69 |
| Display: | Sleep Mode |
| Description: | Sleep Mode |
| Causes: | It means that the printer fuser is turned off, and the power consumption is minimized. |
| Remedy: | 1) Check the harness connected between the Engine controller and the paper size board. (If the harness is out, insert it to the connector.) 2) In the Engine diagnostic mode, operate the MPF trans sensor to check if it is operating. (If it is not operating, replace the paper size board.) 3) Replace the MPF transfer. |
| Error code: | 70 |
| Display: | No Paper |
| Description: | No Paper |
| Causes: | No paper in the paper cassette. |
| Error code: | 71 |
| Display: | Paper Jam 0 |
| Description: | Paper Jam 0 |
| Causes: | The front part of paper is jammed between pickup unit and Feed sensor. |
| Error code: | 72 |
| Display: | Paper Jam 1 |
| Description: | Engine Firmware Failure The Engine Control Board detected a firmware error. |
| Causes: | • Engine Control Board, Pl9.1.16 • EEPROM Board, PL9.1.12 |
| Remedy: | 1 Cycle printer power. Does the error persist? Go to Step 2. Complete 2 Is P/J144 on the EEPROM Board properly seated and defect free? Go to Step 3. Reseat P/J144 or replace the EEPROM Board. 3 Turn printer power off and then back on. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 73 |
| Display: | Paper Jam 2 |
| Description: | Paper Jam 2 |
| Causes: | The front part of paper is jammed just after passing through the discharge sensor. |
| Error code: | 95 |
| Display: | LSU Not Ready |
| Description: | Non-Xerox Imaging Unit A Imaging Unit CRUM I.D. error indicates that a non-Xerox Imaging Unit is installed. |
| Causes: | • Imaging Unit, PL6.1.1 • CRUM Board, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9 |
| Remedy: | 1 Check the Imaging Unit part number. Is the Imaging Unit a genuine Xerox Phaser 6300/6350 part? Go to Step 2. Replace the Imaging Unit. 2 Check the Imaging Unit for damage. Is the Imaging Unit damaged? Replace the Imaging Unit. Go to Step 4. 3 Replace the Imaging Unit. Does the error persist? Go to Step 5. Complete 4 Check the CRUM connection. Is P/J710 connected to the harness? Go to Step 3. Connect the CRUM 5 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J710 <=> J484. Go to Step 4. Replace the PHD2 Harness. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J484. 2. Check continuity between J48<=>P484. Go to Step 5. Replace the FAN/ PHD/MOT Harness. 7 Replace the Imaging Unit. Does the error persist? Replace the Engine Control Board. Complete |
