Samsung ML-6050

Рейтинг

Парткаталог
Коды ошибок

Модули

Main Exploded View

Second Cassette Frame Exploded View

Cassette Exploded View

Fuser Exploded View

Motor Exploded View

Cover Exploded View

Pick-Up Exploded View

Frame Exploded View

Second Cassette Exploded View

Детали

Деталь:	ELA HOU-SCF(ML-6050)
Парткод:	JC96-01268A

Деталь:	E-ring
Парткод:	6044-000126

Деталь:	BEARING ROLLER IDLER
Парткод:	JC66-10304A

Деталь:	TAPTITE SCREW
Парткод:	6003-000179

Деталь:	TAPTITE SCREW
Парткод:	6003-000344

Деталь:	FOOT RUBBER
Парткод:	JC61-40301A

Деталь:	GUIDE INNER UPPER
Парткод:	JC72-40307B

Деталь:	Gear-Feed
Парткод:	JC66-40014A

Деталь:	ROLLER-INNER UPPER
Парткод:	JC75-10028A

Деталь:	E-ring
Парткод:	6044-000125

Деталь:	GEAR DOUBLE OPTION
Парткод:	JC66-40363A

Деталь:	BRKT MOTOR (SCF)
Парткод:	JC70-10986A

Деталь:	STEP MOTOR
Парткод:	3101-001158

Деталь:	SHIELD-PCB
Парткод:	JC70-10451A

Деталь:	COVER-LEFT
Парткод:	JC72-40368B

Деталь:	TAPTITE SCREW
Парткод:	6002-000194

Деталь:	MACHINE SCREW
Парткод:	6001-000131

Деталь:	SOLENOID-MAGNET
Парткод:	JC33-10001A

Деталь:	HUB CLUTCH
Парткод:	JC72-40587A

Деталь:	SPRING-TS,CLUTCH
Парткод:	JC61-70331A

Деталь:	GEAR IDLER OPTION
Парткод:	JC66-40365A

Деталь:	GEAR IDLE Z19
Парткод:	JC66-40012A

Деталь:	GUIDE RAIL
Парткод:	JC72-40371A

Деталь:	BEARING-FEED
Парткод:	JC72-40531A

Деталь:	GEAR P/UP OPTION
Парткод:	JC66-40364A

Деталь:	COLLAR CLUTCH P1
Парткод:	JC72-40569B

Деталь:	CBF HARNESS
Парткод:	JC39-40544A

Деталь:	PBA MAIN
Парткод:	JC92-01077A

Деталь:	CBF HARNESS
Парткод:	JC39-40305A

Деталь:	Label Warning
Парткод:	JC68-20417A

Деталь:	LABEL(R)-SCF(12)
Парткод:	JC68-30936A

Деталь:	Cover-Rear
Парткод:	JC72-40362B

Деталь:	FRAME UPPER
Парткод:	JC70-10027A

Деталь:	FRAME LEFT(SCF)
Парткод:	JC70-10023A

Деталь:	ACTUATOR-ARM
Парткод:	JC72-40370A

Деталь:	CS STOP RING
Парткод:	6044-000001

Деталь:	PIN PARELLED,P/U
Парткод:	JC70-40360A

Деталь:	STOPPER-SCF
Парткод:	JC72-41347A

Деталь:	MACHINE SCREW
Парткод:	6001-001532

Деталь:	FRAME LOWER
Парткод:	JC70-11065A

Деталь:	SHAFT PICKUP
Парткод:	JC70-40002A

Деталь:	IDLE-SCF
Парткод:	JC72-41 348A

Деталь:	HODER-HOUSING
Парткод:	JC72-40654A

Деталь:	RUBBER P/UP
Парткод:	JC73-40907A

Деталь:	BRKT SUPPORT
Парткод:	JC70-10461A

Деталь:	COVER-RIGHT
Парткод:	JC72-40367B

Деталь:	TAPTITE SCREW
Парткод:	6003-000205

Деталь:	GROUND ROLLER
Парткод:	JC70-10467A

Деталь:	FRAME RIGHT(SCF)
Парткод:	JC70-10022A

Деталь:	MACHINE SCREW
Парткод:	6001-000153

Деталь:	CABLE CLAMP
Парткод:	6502-000003

Деталь:	MEA RACK-FEEDER CAS
Парткод:	JC97-01077A

Деталь:	PMO-TRAY-MANUAL
Парткод:	JC72-41387A

Деталь:	PMO-HOLDER FINGER
Парткод:	JC72-41182A

Деталь:	IMP, FINGER
Парткод:	JC70-10213A

Деталь:	IMP, GUIDE PLATE-PAPER
Парткод:	JC70-10219A

Деталь:	SPRING-KNOCK UP
Парткод:	JC61-70951A

Деталь:	LOCKER-PLATE
Парткод:	JC72-41210A

Деталь:	MMP, PAD
Парткод:	JC73-10911A

Деталь:	LABEL-PLATE
Парткод:	JC68-30929A

Деталь:	IPR-PLT KNOCK UP(12)
Парткод:	JC70-11022A

Деталь:	SPRING-LOCKERPLATE
Парткод:	JG61-70531A

Деталь:	LABEL-HEIGHT
Парткод:	JG68-30572A

Деталь:	PMO-GUIDE LEGAL
Парткод:	JC72-41393A

Деталь:	IPR-BRACKET_LEGAL
Парткод:	JC70-11086A

Деталь:	PMO-GUIAE_LETTER
Парткод:	JC72-41392A

Деталь:	IPR-BRACKET_LETTER
Парткод:	JC70-11087A

Деталь:	IPR-TENSION_LETTER
Парткод:	JC70-11085A

Деталь:	PMO-ADJUSTER_S CAST
Парткод:	JC72-41394A

Деталь:	IPR-GUIDE-PLATE
Парткод:	JC70-10993A

Деталь:	PMO-FRAME_CASSETTE, P
Парткод:	JC72-41382A

Деталь:	SCREW-TAPTITE M3x10 FH, WHITE
Парткод:	6003-000002

Деталь:	GUIDE-CASSETTE, M
Парткод:	JC72-00013A

Деталь:	PMO-GUIDE SUB CAST.
Парткод:	JC72-41225A

Деталь:	PMO-GUIDE REAR
Парткод:	JC72-41180A

Деталь:	ELAHOU-FUSER(110V)
Парткод:	JC96-01093A

Деталь:	ELA HOU-FUSER(220V)
Парткод:	JC96-01094A

Деталь:	CBF-HARNESS-FU(110)
Парткод:	JC39-40609A

Деталь:	CBF-HARNESS-FU(220)
Парткод:	JC39-40610A

Деталь:	SCREW-MACHINE M3x6, BH+
Парткод:	6001-000131

Деталь:	SCREW-TAPTITE M3x12, FH+
Парткод:	6003-000198

Деталь:	THERMISTOR-NTC
Парткод:	1404-001117

Деталь:	SCREW-TAPTITE M3x8, BH+
Парткод:	6003-000119

Деталь:	NPR-ELECTRODE FU R
Парткод:	JC71-10201A

Деталь:	PMO-ROLLER EXIT F/UP
Парткод:	JC72-40342A

Деталь:	SPRING-PS, EXIT F/UP
Парткод:	JC70-11067A

Деталь:	PMO-ACTUATOR EXIT
Парткод:	JC72-41079A

Деталь:	BEARING-EXIT FU
Парткод:	JC66-10201A

Деталь:	IPR-FUSER LOWER
Парткод:	JC70-10983A

Деталь:	PMO-BUSHING PR
Парткод:	JC72-41078A

Деталь:	SPRING-PR
Парткод:	JC61-70923A

Деталь:	PMO-BUSHING HR, R
Парткод:	JC72-41077A

Деталь:	NEX-ROLLER HEAT
Парткод:	JC71-20901A

Деталь:	MEC-ROLLER PRESSURE
Парткод:	JC75-10956A

Деталь:	PMO-GUIDE PATH
Парткод:	JC72-41074A

Деталь:	PMO-BUSHING HR, L
Парткод:	JC72-41076A

Деталь:	GEAR-FUSER
Парткод:	JC66-40926A

Деталь:	MEC-ROLLER EXIT, FU/LR
Парткод:	JC75-10955A

Деталь:	PMO-FUSER REAR
Парткод:	JC72-41075A

Деталь:	LAMP-HALOGEN
Парткод:	4713-001075

Деталь:	LAMP-HALOGEN
Парткод:	4713-001076

Деталь:	BEARING-EXIT FU L
Парткод:	JC66-10200A

Деталь:	GEAR-EXIT
Парткод:	JC66-40209A
Цена:	260 ₽

Деталь:	PMO-FUSER UPPER
Парткод:	JC72-41073A

Деталь:	Ring-CS
Парткод:	6044-000001

$samsung\JC66-40964A.jpg$

Деталь:	GEAR-EXIT, L/ID
Парткод:	JC66-40964A
Цена:	500 ₽

Деталь:	NPR-ELECTRODE FUSER
Парткод:	JC71-10902A

$xerox\4712-000001.jpg$

Деталь:	THERMOSTAT
Парткод:	4712-000001

Деталь:	PMO-CLAW SEPARATOR
Парткод:	JC72-41064A

Деталь:	SPRING-CLAW
Парткод:	JC61-70922A

Деталь:	ELA HOU-MOTOR MAIN
Парткод:	JC96-01099A

Деталь:	IPR-BRKT_GEAR
Парткод:	JC70-10984A

Деталь:	SCREW-MACHINE M3x6
Парткод:	6001-000131

Деталь:	GEAR-FUSER DRIVE
Парткод:	JC66-40378A

Деталь:	GEAR-125/18
Парткод:	JC66-40376A

Деталь:	IPR-BRKT, MOTOR
Парткод:	JC70-10985A

Деталь:	MOTOR-STEP
Парткод:	3101-001144

Деталь:	GEAR-132/50 (12)
Парткод:	JC66-40959A

Деталь:	GEAR-IDLE, FU
Парткод:	JC66-40377A

Деталь:	GEAR-IDLE OPC (12)
Парткод:	JC66-40960A

Деталь:	GEAR-OPC DRV2
Парткод:	JC66-40001A

Деталь:	GEAR-OPC DRIVE (12)
Парткод:	JC66-40961A

Деталь:	GEAR-FEED DRV (12)
Парткод:	JC66-40962A

Деталь:	FILM-BRACKET
Парткод:	JC73-00002A

Деталь:	ELA HOU-CVR_MAIN
Парткод:	JC96-01365A

Деталь:	ELA HOU-CVR_MAIN
Парткод:	JC96-01364A

Деталь:	SPRING-HOOK LEVER
Парткод:	6107-000133

Деталь:	LEVER-HOOK
Парткод:	JC72-40325A

Деталь:	PLATE-SPRING, DEV
Парткод:	JC70-10223A

Деталь:	Screw-Taptite
Парткод:	6003-000002

Деталь:	SPRING-COVER OPEN, L
Парткод:	JC61-70944A

Деталь:	STACKER-SUB
Парткод:	JC72-41220A

Деталь:	HINGE-HSG, R
Парткод:	JC72-41216A

Деталь:	SHAFT-COVER OPEN
Парткод:	JC70-10228A

Деталь:	PAD-DUMMY
Парткод:	JC73-30912A

Деталь:	BRUSH-ANTI
Парткод:	JC74-40902A

Деталь:	GROUND-ANTI
Парткод:	JC70-11057A

Деталь:	GUIDE-DUMMY
Парткод:	JC72-41111A

Деталь:	COVER-EXIT
Парткод:	JC72-41221A

Деталь:	LOCKER-EXIT
Парткод:	JC72-41286A

Деталь:	Screw-Taptite
Парткод:	6003-000196A

Деталь:	COVER-MAIN
Парткод:	JC72-41214A

Деталь:	BUTTON-C/O
Парткод:	JC72-40336D

Деталь:	SPRING-CS (BUTTON)
Парткод:	6107-000117

Деталь:	SPRING-COVER OPEN, R
Парткод:	JC61-70945A

Деталь:	COVER-FRONT, LED
Парткод:	JC72-41215F

Деталь:	COVER-FRONT, XAR
Парткод:	JC72-41215E

Деталь:	WINDOW-LED
Парткод:	JC72-41397A

Деталь:	BUTTON-PANEL, LED
Парткод:	JC72-41219A

Деталь:	PBA-PANEL, LED
Парткод:	JC92-00346A

Деталь:	CAP-PANEL WIRE
Парткод:	JC72-41222A

Деталь:	MEA RACK-FEEDER
Парткод:	JC97-01078A

Деталь:	PLT, GEAR-PICK UP
Парткод:	JC66-40219A

Деталь:	Washer-Plain
Парткод:	6031-000021

Деталь:	PLT, BEARING-PICK UP
Парткод:	JC66-10202A

Деталь:	IMP, SHAFT-PICK UP
Парткод:	JC70-10231A

Деталь:	PLT, LEVER-PICK UP
Парткод:	JC72-40254A

Деталь:	SPRING PICK-UP
Парткод:	JC61-70966A

Деталь:	PLT, FRAME-FEED
Парткод:	JC72-41115A

Деталь:	PMP, IDLE-PICKUP
Парткод:	JC72-41234A

Деталь:	PLT, HOUSING-PICK UP
Парткод:	JC72-40252A

Деталь:	PLT, RUBBER-PICKUP
Парткод:	JC73-40907A

Деталь:	IMP, GUIDE-FEED
Парткод:	JC70-10992A

Деталь:	SPRING-FEED (2)
Парткод:	JC61-70942A

Деталь:	PLT, HOLDER-FEED2
Парткод:	JC72-41185A

Деталь:	PLT, SUB HOLER-FEED, SMALL
Парткод:	JC72-40266A

Деталь:	PLT, ROLLER-FEED, LARGE
Парткод:	JC72-40261A

Деталь:	PLT, ROLLER-FEED, SMALL
Парткод:	JC72-40262A

Деталь:	IMP, SHAFT-FEED, IDLER
Парткод:	JC70-10230A

Деталь:	PLT, ROLLER-FEED, DRIVE
Парткод:	JC72-41295A

Деталь:	SCREW (M3X6 FH+, BLK)
Парткод:	6003-000002

Деталь:	PLT, HOLDER-FEED1
Парткод:	JC72-41184A

Деталь:	SPRING-FEED (1)
Парткод:	JC61-70941A

Деталь:	IMP, SHAFT-FEED
Парткод:	JC70-10229A

Деталь:	PLT, GEAR-FEED
Парткод:	JC66-40375A

Деталь:	PLT, GEAR-P/UP DRIVE
Парткод:	JC66-40219A

Деталь:	IMP, GND-FEED
Парткод:	JC70-10991A

Деталь:	ELAHOU-FRAME (12)
Парткод:	JC96-01338B

Деталь:	SHEET COVER OPC
Парткод:	JC72-40909A

Деталь:	GUIDE-SKEW(12)
Парткод:	JC72-41350A

Деталь:	ACTUATOR-FEED(12)
Парткод:	JC72-00012A

Деталь:	Spring-CS
Парткод:	6107-000104

Деталь:	CONNECTOR TERMINAL2
Парткод:	3712-000165

Деталь:	SCREW-TAPTITE 310
Парткод:	6003-000002

Деталь:	CONNECTOR TERMINAL1
Парткод:	3712-000166

Деталь:	GROUND-PLT MOTOR
Парткод:	JC70-10013A

Деталь:	CBF HARNESS
Парткод:	JC39-40576A

Деталь:	ROLLER EXIT MAIN
Парткод:	JC72-41081A

Деталь:	GROUND-OPC(12)
Парткод:	JC70-11070A

Деталь:	GUIDE-DUST
Парткод:	JC70-11068A

Деталь:	MOTOR BOARD
Парткод:	JC92-01045A

Деталь:	ELA-DEVELOPER, GUID
Парткод:	JC96-00290A

Деталь:	FAN DC 24V
Парткод:	3103-001049

Деталь:	SWITCH
Парткод:	JC39-00004A

Деталь:	MEA RACK-BRKT_EXIT
Парткод:	JC97-01198A

Деталь:	EARTH PLATE FUSER
Парткод:	JC70-10911A

Деталь:	ELA HOU-PTL
Парткод:	JC96-01150A

Деталь:	CBF HARNESS
Парткод:	JC39-40546A

Деталь:	GND PLATE G/TR
Парткод:	JC70-10980A

Деталь:	GROUND-EXIT
Парткод:	JC70-11058A

Деталь:	MEA RACK-TR HOLDER, L
Парткод:	JC97-01079A

Деталь:	Roller-Transfer
Парткод:	JC75-10962A

Деталь:	HEA RACK-HOU EXIT
Парткод:	JC97-01104A

Деталь:	MEA RACK-TR HOLDER, R
Парткод:	JC97-01071A

Деталь:	GEAR-TRANSFER (12)
Парткод:	JC66-40949A

Деталь:	LSU-HARNESS
Парткод:	JC39-40540A

Деталь:	CBF-HARNESS
Парткод:	JG39-40179A

Деталь:	GUIDE-FUSER
Парткод:	JC72-41223A

Деталь:	BASE FRAME
Парткод:	JC72-41113A

Деталь:	SHIELD CAP WIRE
Парткод:	JC70-10003A

Деталь:	SHIELD ICU
Парткод:	JC70-10225A

Деталь:	CBF HARNESS
Парткод:	JC39-40009A

Деталь:	FILM-EMI
Парткод:	JC74-10908A

Деталь:	DAMPER-PLATE
Парткод:	JC72-41288A

Деталь:	GROUND-ICU
Парткод:	JC70-10006A

Деталь:	GUIDE-TRANSFER
Парткод:	JC70-1 0220A

Деталь:	SHEET GUIDE-TR
Парткод:	JC74-10907A

Деталь:	SCREW-TAPTITE 38
Парткод:	6003-000119

Деталь:	PLATE-SAW
Парткод:	JC70-10232A

Деталь:	HOLDER-SAW PLATE
Парткод:	JC72-40247A

Деталь:	ELA HOU-THERMISTOR
Парткод:	JC96-01148A

Деталь:	SPRING-CVR OPEN (12)
Парткод:	JC61-70964A

Деталь:	ACTUATOR-C/O
Парткод:	JC72-40269A

Деталь:	ELA-DEVELOPER, GUID
Парткод:	JC96-00291A

Деталь:	ROM COVER
Парткод:	JC72-41186A

Деталь:	MEA RACK-EMPTY_ACT
Парткод:	JC97-01207A

Деталь:	ACTUATOR-TR
Парткод:	JC72-41287A

Деталь:	HOLDER-ACTUATOR
Парткод:	JC72-41289A

Деталь:	PBA MAIN-CLN
Парткод:	JC92-01084A

Деталь:	CBF-HARNESS
Парткод:	JC39-4051 3A

Деталь:	ELA-HOU CLEANING PLT
Парткод:	JC96-01229A

Деталь:	CAP-GND WIRE
Парткод:	JC72-00011A

Деталь:	CBF-HARNESS MOTOR
Парткод:	JC39-40575A

Деталь:	ROLLER EXIT FR
Парткод:	JC72-41082A

Деталь:	Spring-CS
Парткод:	6107-000106

Деталь:	HOLDER-EXIT
Парткод:	JC72-41080A

Деталь:	GUIDE-DEV L
Парткод:	JC72-40274A

Деталь:	SPRING-PS G/DEV
Парткод:	JC61-70001A

Деталь:	GEAR-EXIT/U ID
Парткод:	JC66-40006A

Деталь:	RING-C ID3
Парткод:	6044-000159

$samsung\JC66-40964A.jpg$

Деталь:	GEAR-EXIT, IDLE(Z17)
Парткод:	JC66-40964A
Цена:	500 ₽

Деталь:	BRACKET_EXIT
Парткод:	JC70-11075A

Деталь:	EARTH TRNAS (12)
Парткод:	JC70-11023A

Деталь:	HOLDER-PTL
Парткод:	JC72-41187A

Деталь:	PBA MAIN PTL
Парткод:	JC92-01050A

Деталь:	CBF HARNESS
Парткод:	JC39-40543A

Деталь:	BUSHING-TR12 (L)
Парткод:	JC72-41283A

Деталь:	SPRING-TR (12)
Парткод:	JC61-70940A

Деталь:	HOLDER-TR L (12)
Парткод:	JC72-41285A

Деталь:	SPRING-PLATE (12)
Парткод:	JC70-11050A

Деталь:	GEAR-EXIT
Парткод:	JC66-40209A
Цена:	260 ₽

Деталь:	BEARING-EXIT
Парткод:	JC75-10529A

Деталь:	ROLL EXIT FR/UP
Парткод:	JC75-10957A

Деталь:	MEA Rack-Exit Roller
Парткод:	JC97-01098A

Деталь:	HOUSING-EXIT (250)
Парткод:	JC72-41114A

Деталь:	BUSHING-TR12 (R)
Парткод:	JC72-41060A

Деталь:	HOLDER-TR R (12)
Парткод:	JC72-41062A

Деталь:	GUIDE-DEV R
Парткод:	JC72-40275A

Деталь:	SPRING-EMPTY
Парткод:	JC61-70965A

Деталь:	ACTUATOR-EMPTY12
Парткод:	JC72-41290A

Деталь:	MEA RACK-CAST.SCF
Парткод:	JC97-01196A

Деталь:	GUIDE CST
Парткод:	JC72-40306A

Деталь:	PMO-GUIDE-2ND CAST.
Парткод:	JC72-41227A

Деталь:	PLATE-COLOR
Парткод:	JC72-41226A

Деталь:	SPRING ES
Парткод:	6107-001047A

Деталь:	ROLLER EXIT
Парткод:	JC72-40361A

Деталь:	TAPTITE SCREW
Парткод:	6003-000196

Деталь:	SPRING KNOCKUP
Парткод:	JC61-70951A

Деталь:	GUIDE SCF
Парткод:	JC70-11076A

Деталь:	FINGER
Парткод:	JC70-10213A

Деталь:	PLT KNOCK-UP (12)
Парткод:	JC70-11022A

Деталь:	MMP, PAD
Парткод:	JC73-10911A

Деталь:	LABEL(R) PLATE
Парткод:	JC68-30929A

Деталь:	LOCKER-PLATE
Парткод:	JC72-41 21 0A

Деталь:	SPRING-LOCKER PLATE
Парткод:	JG61-70531A

Деталь:	GUIDE PAPER
Парткод:	JC70-10219A

Деталь:	LABEL(R) HEIGHT
Парткод:	JG68-30572A

Деталь:	GUIDE-LEGAL
Парткод:	JC72-41180A

Деталь:	IPR-BRACKET_LEGAL
Парткод:	JC70-11086A

Деталь:	PMO-GUIDE_LETTER
Парткод:	JC72-41392A

Деталь:	IPR-BRACKET_LETTER
Парткод:	JC70-11087A

Деталь:	IPR-TENSION_LETTER
Парткод:	JC70-11085A

Деталь:	GUIDE-SIDE CASSETTE
Парткод:	JC72-41116A

Деталь:	GUIDE PLATE
Парткод:	JC70-10993A

Деталь:	FRAME-CASSETTE
Парткод:	JC72-41183A

Деталь:	PMO-GUIDE REAR
Парткод:	JC72-41180A

Error code:	01
Display:	ERROR CONDITION INVALID HEAD
Description:	The ERROR light flashes.
Causes:	The printhead was replaced with one that is not a genuine Zebra™ printhead.
Remedy:	Install a genuine Zebra printhead.

Error code:	02
Display:	ERROR CONDITION RIBBON OUT
Description:	The printer stops; the ERROR light flashes.
Causes:	In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly.
Remedy:	Load ribbon correctly. 1. Load ribbon correctly. See Load Ribbon on page 64. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Load media correctly. See Load Media on page 58. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Print a sensor profile. See Print Sensor Profile on page 89. The ribbon out threshold (marked by the word RIBBON) is likely too high, above the black area that indicates where the ribbon is detected. 2. Calibrate the sensors or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73.

Error code:	03
Display:	WARNING RIBBON IN
Description:	The ERROR light flashes.
Causes:	Ribbon is loaded, but the printer is set for direct thermal mode.
Remedy:	Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81.

Error code:	04
Display:	ERROR CONDITION PAPER OUT
Description:	The printer stops; the ERROR light flashes.
Causes:	The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded.
Remedy:	Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration.

Error code:	05
Display:	ERROR CONDITION HEAD OPEN
Description:	The printer stops; the ERROR light flashes.
Causes:	The printhead is not fully closed. The head open sensor is not working properly.
Remedy:	Replace the sensor.

Error code:	06
Display:	THERMISTOR FAULT
Description:	The ERROR light flashes.
Causes:	The printhead has a faulty thermistor.
Remedy:	Replace the printhead.

Error code:	07
Display:	WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD
Description:	The printer stops; the ERROR light is on; the printer cycles through these three messages.
Causes:	The printhead data cable is not properly connected. The printhead has a faulty thermistor.
Remedy:	Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead.

Error code:	08
Display:	WARNING HEAD COLD
Description:	The printer prints while the ERROR light flashes.
Causes:	The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor.
Remedy:	Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead.

Error code:	09
Display:	WARNING HEAD TOO HOT
Description:	The printer stops; the ERROR light flashes.
Causes:	The printhead is over temperature.
Remedy:	Allow the printer to cool. Printing automatically resumes when the printhead elements cool to an acceptable operating temperature.

Error code:	10
Display:	DEFRAGMENTING
Description:	The printer stops.
Causes:	The printer is defragmenting memory.
Remedy:	Caution • Do NOT turn off the printer power during defragmenting. Doing so can damage the printer. Allow the printer to finish defragmenting. If you get this error message frequently, check your label formats. Formats that write to and erase memory frequently may cause the printer to defragment often. Using properly coded label formats usually minimizes the need for defragmenting. If this error message does not go away, contact Technical Support. The printer requires service.

Деталь:	ELAHOU-FRAME(12)
Парткод:	JC96-01092A

Деталь:	ELA-DEVE UNIT
Парткод:	ML+6000D5

Деталь:	UNIT-LSU
Парткод:	JC59-10507A

Деталь:	PRO-COVER_SIMM
Парткод:	JC72-41224A

Error code:	11
Display:	ERROR CONDITION CUTTER JAM
Description:	The printer stops; the ERROR light flashes.
Causes:	Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers. The cutter blade is in the media path.
Remedy:	Turn off the printer power and unplug the printer. Inspect the cutter module for debris and clean as needed following the cleaning instructions in Clean the Cutter Module on page 135.

Error code:	12
Description:	General print quality issues
Causes:	The printer is set at the incorrect print speed. You are using an incorrect combination of labels and ribbon for your application. The printer is set at an incorrect darkness level. The printhead is dirty. Incorrect or uneven printhead pressure. The printhead is improperly balanced.
Remedy:	For optimal print quality, set the print speed to the lowest possible setting for your application via control panel, the driver, or the software. See Adjust Print Speed on page 79. You may want to perform the FEED Self Test on page 120. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. For optimal print quality, set the darkness to the lowest possible setting for your application via the control panel, the driver, or the software. See Adjust Print Darkness on page 78. You may want to perform the FEED Self Test on page 120 to determine the ideal darkness setting. Clean the printhead. See Clean the Printhead and Platen Roller on page 131. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Adjust the printhead balance.

Error code:	13
Description:	Long tracks of missing print on several labels
Causes:	Print element damaged.
Remedy:	Replace the printhead.

Error code:	14
Description:	Wrinkled ribbon
Causes:	Ribbon fed through the machine incorrectly. Incorrect burn temperature. Incorrect or uneven printhead pressure. Media not feeding properly; walking from side to side. The strip plate needs adjusting. The printhead needs vertical adjustment. The printhead is improperly balanced. The printhead and platen roller need to be realigned.
Remedy:	See Load Ribbon on page 64. Set the darkness to the lowest possible setting for good print quality. See Adjust Print Darkness on page 78. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Make sure that media is snug by adjusting the media guide, or call a service technician. Adjust the printhead balance.

Error code:	15
Description:	Printing too light or too dark over the entire label
Causes:	The media or ribbon is not designed for high-speed operation. You are using an incorrect combination of media and ribbon for your application. You are using ribbon with direct thermal media. Incorrect or uneven printhead pressure.
Remedy:	Replace supplies with those recommended for high-speed operation. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. Direct thermal media does not require ribbon. To check if you are using direct thermal media, perform the label scratch test in When to Use Ribbon on page 62. Set the pressure to the minimum needed. See Adjust Printhead Pressure on page 70.

Error code:	16
Description:	Smudge marks on labels
Causes:	The media or ribbon is not designed for high-speed operation.
Remedy:	Replace supplies with those recommended for high-speed operation.

Error code:	17
Description:	Misregistration/skips labels
Causes:	The printer is not calibrated. Improper label format.
Remedy:	Recalibrate the printer. Use correct label format.

Error code:	18
Description:	Misregistration and misprint of one to three labels
Causes:	The platen roller is dirty. Media does not meet specifications.
Remedy:	See Clean the Printhead and Platen Roller on page 131. Use media that meets specifications.

Error code:	19
Description:	Vertical drift in top-of-form position
Causes:	The printer is out of calibration. Vertical drift occurs during normal printer operation. Note • A vertical drift of ± 4 to 6 dot rows (approximately 0.5 mm) is within normal tolerances. The platen roller is dirty.
Remedy:	Recalibrate the printer. Calibrate the printer. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131.

Error code:	20
Description:	Vertical image or label drift
Causes:	The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media.
Remedy:	Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation.

Samsung ML-6050

Модули

Детали

Коды ошибок

Описание

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Error code:	21
Description:	The bar code printed on a label does not scan.
Causes:	The bar code is not within specifications because the print is too light or too dark. Not enough blank space around the bar code.
Remedy:	Perform the FEED Self Test on page 120. Adjust the darkness or print speed settings as necessary. Leave at least 1/8 in. (3.2 mm) between the bar code and other printed areas on the label and between the bar code and the edge of the label.

Error code:	22
Description:	Loss of printing registration on labels. Excessive vertical drift in top-of-form registration.
Causes:	The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly.
Remedy:	Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58.

Error code:	23
Description:	Auto Calibrate failed.
Causes:	Media or ribbon is loaded incorrectly. The sensors could not detect the media or ribbon. The sensors are dirty or positioned improperly. The sensors are dirty, or media is positioned improperly for the sensors to detect. The media type is set incorrectly.
Remedy:	Ensure that media and ribbon are loaded correctly. Manually calibrate the printer. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Ensure that the sensors are clean and that media is positioned properly. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81.

Error code:	24
Description:	A label format was sent to the printer but was not recognized. The DATA light does not flash.
Causes:	The communication parameters are incorrect.
Remedy:	Check the printer driver or software communications settings (if applicable). If you are using serial communication, check the serial port setting in the control panel menu. See Set Serial Communications on page 91. If you are using serial communication, make sure you are using a null modem cable or a null modem adapter. Using the control panel controls, check the protocol setting. It should be set to NONE. See Set Protocol on page 93. If a driver is used, check the driver communication settings for your connection.

Error code:	25
Description:	A label format was sent to the printer. Several labels print, then the printer skips, misplaces, misses, or distorts the image on the label.
Causes:	The serial communication settings are incorrect.
Remedy:	Ensure that the flow control settings match. Check the communication cable length. See Table 5 on page 48 for requirements. Check the printer driver or software communications settings (if applicable).

Error code:	27
Description:	Broken or melted ribbon
Causes:	Darkness setting too high.
Remedy:	1. Reduce the darkness setting. 2. Clean the printhead thoroughly.

Error code:	28
Description:	The printer does not detect when the ribbon runs out. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly.
Causes:	The ribbon-out threshold is set too high to detect the ribbon. On a sensor profile, the ribbon-out threshold (circled in Figure 15) appears above the black bars that indicate the ribbon. This happens if you calibrate the printer without ribbon and later insert ribbon without recalibrating the printer or loading printer defaults.
Remedy:	1. Print a sensor profile (see Print Sensor Profile on page 89), and note the location of the ribbon-out threshold (circled in Figure 15). 2. Calibrate the printer, this time using ribbon, or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. Important • Loading defaults resets all printer parameters back to factory defaults. 3. Print another sensor profile, and compare it to the first one. 4. If the ribbon-out threshold is still too high, you may manually change the value.

Error code:	29
Description:	The ribbon light is on even though ribbon is loaded correctly.
Causes:	The printer was not calibrated for the label and ribbon being used.
Remedy:	Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90.

Error code:	30
Description:	The LCD displays a language that I cannot read
Causes:	The language parameter was changed through the control panel or a firmware command.
Remedy:	1. Press SETUP/EXIT to enter configuration mode. 2. Press MINUS (-). The printer displays the LANGUAGE parameter in the current language. Even if you cannot recognize the characters displayed, you can still scroll to another language. 3. Press SELECT to select the parameter. 4. Press PLUS (+) or MINUS (-) to scroll through the choices until you find a language that you can read. 5. Press SETUP/EXIT. The LCD displays SAVE CHANGES in the original language. 6. Press SETUP/EXIT again to exit configuration mode and save the changes (if the language does not change, you may need to scroll to a different save option by pressing PLUS (+) or MINUS (-) in the previous step). 7. Repeat this process, if necessary, until you reach the desired language.

Error code:	31
Description:	The LCD is missing characters or parts of characters
Causes:	The LCD may need replacing.
Remedy:	Run the Power-On Self Test on page 117 and check that the LCD display shows all characters. If not, replace the LCD.