
Samsung ProXpress M4530ND
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A4
Число страниц в месяц
200000
Скорость печати
A4
47
Цветность печати
черно-белая
Общие характеристики |
|
---|---|
Область применения |
большой офис |
Тип устройства |
Принтер |
Макс. формат |
A4 |
Факс |
|
Сканер |
|
Печать фотографий |
|
Копир |
|
Телефон |
|
Размещение |
настольный |
Тип |
лазерный/светодиодный |
Цветность печати |
|
Технология печати |
лазерная |
Число страниц в месяц |
200 000 |
Принтер |
|
Пигментные чернила |
|
Печать без полей |
|
Система непрерывной подачи чернил |
|
Макс, длина отпечатка |
356 |
Макс, ширина отпечатка |
216 |
Двусторонняя печать |
![]() |
Прямая печать |
![]() |
Макс, разрешение для ч/б печати |
|
По X | 1 200 |
По Y | 1 200 |
Скорость ч/б печати |
|
A4 | 47 |
Время выхода первого отпечатка |
|
Ч/б | 6,5 |
Сканер |
|
Слайд-адаптер |
|
Стандарт WIA |
|
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Расходные материалы |
|
Количество картриджей |
1 |
Ресурс ч/б картриджа/тонера |
7 000 |
Печать на: |
|
Фотобумаге |
|
CD/DVD |
|
Рулоне |
|
Этикетках |
![]() |
Матовой бумаге |
![]() |
Конвертах |
![]() |
Глянцевой бумаге |
![]() |
Карточках |
![]() |
Пленках |
![]() |
Плотность бумаги |
|
Минимальная | 60 |
Максимальная | 220 |
Факс |
|
Цветной |
|
PC Fax |
|
Телефон |
|
Проводная трубка |
|
Caller ID |
|
Автоответчик |
|
Спикерфон |
|
Стандарт DECT |
|
АОН |
|
Беспроводная трубка |
|
Языки управления |
|
PostScript 2 |
|
PCL 5c |
|
PPDS |
|
PostScript |
![]() |
PCL 6 |
![]() |
PCL 5e |
![]() |
![]() |
|
PostScript 3 |
![]() |
Лотки |
|
Емкость лотка ручной подачи |
50 |
Подача бумаги |
|
Стандартная | 650 |
Максимальная | 2 300 |
Вывод бумаги |
|
Стандартный | 500 |
Финишер |
|
Брошюровщик |
|
Степлер |
|
Сортировка со сдвигом |
|
Электронная сортировка |
|
Сортер |
|
Интерфейсы |
|
Wi-Fi |
|
Устройство для чтения карт памяти |
|
FireWire (IEEE 1394) |
|
RS-232 |
|
Инфракрасный порт |
|
AirPrint |
|
LPT |
|
Bluetooth |
|
Wi-Fi 802.11n |
|
Версия USB |
2,0 |
Ethernet (RJ-45) |
![]() |
Веб-интерфейс |
![]() |
USB |
![]() |
Память/Процессор |
|
Объем памяти |
512 |
Макс, объем памяти |
2 048 |
Частота процессора |
1 000 |
Дополнительная информация |
|
Экран |
|
Работа от аккумулятора |
|
Поддержка ОС |
|
DOS |
|
Mac OS |
![]() |
Windows |
![]() |
Linux |
![]() |
Потребляемая мощность |
|
В режиме ожидания | 10 |
При работе | 700 |
Уровень шума |
|
При работе | 54 |
В режиме ожидания | 26 |
Габариты |
|
Вес |
22 |
Глубина |
460 |
Высота |
368 |
Ширина |
431 |
Модули
Exit
DUPLEX
Frame-Base
FRAME-MAIN
Frame-Middle
FRAME-RIGHT
FRAME-PICK UP
MAIN
PAPER FEED
MP-UPPER and MP LOWER
DRIVE-MAIN
Fuser
CASSETTE
TOP-COVER
Frame-Upper
FRAME-LEFT
Детали
Деталь: | EXIT, M4530 |
Парткод: | JC90-01071C |
Деталь: | DRIVE EXIT, ML-5015ND,SEC,1,31,GRAY |
Парткод: | JC93-00349A |
Деталь: | EXIT-ROLLER DUPLEX, ML-5015ND,SEC |
Парткод: | JC90-01092A |
Деталь: | GUIDE-DEFLECTOR, ML-6510ND,PC,NH-1035,BLA |
Парткод: | JC61-03891A |
Деталь: | ROLLER-EXIT_UPPER, ML-6510ND,EPDM,SUM22,6 |
Парткод: | JC66-02663A |
Деталь: | ROLLER-EXIT_LOWER, ML-6510ND,EPDM |
Парткод: | JC66-02664A |
Деталь: | BRUSH-ANTISTATIC, CLP-660,AL+SUS FIBER,22 |
Парткод: | JC67-00295A |
Деталь: | GEAR-M_EXIT UPPER, SCX-6345N/XRX,POM,0.8, |
Парткод: | JC66-01017A |
Деталь: | GEAR-M_EXIT LOWER, SCX-6345N/XRX,POM,0.8, |
Парткод: | JC66-01018A |
Деталь: | GEAR-M-EXIT DUP Z21, ML-3560,POM,1,21,WHT |
Парткод: | JC66-00854A |
Деталь: | FRAME-CAP EXIT, ML-5015ND,ABS+PC,BLACK |
Парткод: | JC61-04283A |
Деталь: | FRAME-EXIT, M4580,ABS+PC,230NH,SPLIT BROW |
Парткод: | JC61-04282B |
Деталь: | CAP-ROLLER_EXIT, ML-6510ND,PC,Black |
Парткод: | JC67-00477A |
Деталь: | PHOTO-INTERRUPTER, TR,BK |
Парткод: | 0604-001325 |
Деталь: | DUPLEX, ML-5015ND,SEC |
Парткод: | JC90-01076A |
Деталь: | GUIDE-DUPLEX REAR, ML-5015ND,ABS,BLACK,GU |
Парткод: | JC61-04267A |
Деталь: | DUPLEX-GUIDE LOWER, ML-5015ND,SEC |
Парткод: | JC90-01087A |
Деталь: | BELT-TIMING GEAR, 32S2M152,CR+GF+NF,T3.2, |
Парткод: | 6602-001588 |
Деталь: | BELT-TIMING GEAR, RUBBER,T1.36,L168MM,BLK |
Парткод: | 6602-001581 |
Деталь: | FRAME-STOPPER CASSETTE, ML-5015ND,SEC |
Парткод: | JC93-00369A |
Деталь: | DUPLEX-FEEDER UPPER, ML-5015ND,SEC |
Парткод: | JC90-01084A |
Деталь: | GUIDE-DUPLEX UPPER, SECC,1.0T,PAPER |
Парткод: | JC61-04221A |
Деталь: | FRAME-PICK UP, ML-5015ND,SEC |
Парткод: | JC93-00383A |
Деталь: | SPRING-TS, SWP B,BK,0.70,ID3.4,5.79 |
Парткод: | 6107-002857 |
Деталь: | ROLLER IDLE-IDLE MP, CLX-9350,POM,SW-01 |
Парткод: | JC66-02291A |
Деталь: | PHOTO-INTERRUPTER, TR,BK |
Парткод: | 0604-001325 |
Деталь: | HOLDER-HARNESS DRAW, ML-5015ND,ABS,BLACK |
Парткод: | JC61-04253A |
Деталь: | HARNESS-FUSER_FR, ML-4510ND,UL10272,AWG26 |
Парткод: | JC39-01444A |
Деталь: | DRIVE-DUPLEX, ML-5015ND,SEC |
Парткод: | JC93-00352A |
Деталь: | HOLDER-DUP LOWER, ML-5015ND,ABS+GF20%,BLA |
Парткод: | JC61-04249A |
Деталь: | SPRING-TS, SWP B,1,6.2 |
Парткод: | 6107-002850 |
Деталь: | BRACKET-SUPPORT FRAME, ML-5015ND,SECC,1.2 |
Парткод: | JC61-04269A |
Деталь: | EXIT, M4530 |
Парткод: | JC90-01071C |
Деталь: | FRAME-UPPER, M4580,SEE |
Парткод: | JC93-00955A |
Деталь: | FRAME-LEFT, ML-5015ND,SEC |
Парткод: | JC93-00364A |
Деталь: | DUPLEX, ML-5015ND,SEC |
Парткод: | JC90-01076A |
Деталь: | FRAME-RIGHT, ML-4510ND,XIC |
Парткод: | JC93-00367B |
Деталь: | BRACKET-CROSS BAR R, ML-5015ND,SECC,1.0T |
Парткод: | JC61-04271A |
Деталь: | HVPS, 24V,21.6V27.6V,MAX 7KV,MAX-2KV,M45 |
Парткод: | JC44-00239B |
Деталь: | PBA-USB HOST, CLX-3170FN,SEC,,,45mm35mm |
Парткод: | JC92-02048A |
Деталь: | FRAME-FEED IDLE, ML-5015ND,SEC |
Парткод: | JC93-00384A |
Деталь: | FRAME-MIDDLE, M4580,SEE |
Парткод: | JC93-00959A |
Деталь: | MP-LOWER, ML-5015ND,SEC |
Парткод: | JC90-01081A |
Деталь: | MP-UPPER, ML-5015ND,SEC |
Парткод: | JC90-01079A |
Деталь: | FAN-DC, CLX-8380ND/XAA,UL10272 AWG26, AM |
Парткод: | JC31-00086A |
Деталь: | DUCT-FAN MAIN, ML-5015ND,ABS,BLACK |
Парткод: | JC67-00516A |
Деталь: | CLUTCH-ELECTRIC, ML-4510ND,POM,2.5kgf.cm |
Парткод: | JC47-00033E |
Деталь: | PBA-COVER OPEN SENSOR, ML-4510ND,SEC,COVE |
Парткод: | JC92-02371A |
Деталь: | SMPS-V2, ML-5010ND,PSPN-Type4-V2,Flyback, |
Парткод: | JC44-00092C |
Деталь: | FDB-PETREL_V2, ML-5010ND,PETREL FDB-V2,AC |
Парткод: | JC44-00204A |
Деталь: | DRIVE-MAIN, M4580,SSDP |
Парткод: | JC93-00923A |
Деталь: | PBA-JOINT, ML-4510ND,PBA-JOINT,FR-1,1L,14 |
Парткод: | JC92-02374A |
Деталь: | COVER-SMPS, ML-5015ND,SEC |
Парткод: | JC95-01410A |
Деталь: | ROLLER IDLE-FEED_DRIVE, ML-5015ND,EPDM,SU |
Парткод: | JC66-02965A |
Деталь: | HOLDER-COVER FRONT L, M4580,PC,BLACK,NH-1 |
Парткод: | JC61-06333A |
Деталь: | HOLDER-COVER FRONT R, M4580,PC,BLACK,NH-1 |
Парткод: | JC61-06334A |
Деталь: | FRAME-TERMINAL, M4580,SEE |
Парткод: | JC93-00960A |

Деталь: | FRAME-ROLLER TRANSFER, ML-501ND,SEC,H12.5 |
Парткод: | JC93-00393A |
Цена: | 2 600 ₽ |
Деталь: | CORE ROTOR, SCX-6320F,STS304,0.1t,SAW |
Парткод: | JC70-10232D |
Деталь: | PHOTO-INTERRUPTER, TR,BK |
Парткод: | 0604-001325 |
Деталь: | ACTUATOR-FEED, ML-5015ND,POM,BLACK,ACTUAT |
Парткод: | JC66-02913A |
Деталь: | ACTUATOR-REGI, ML-5015ND,POM,BLACK,ACTUAT |
Парткод: | JC66-02914A |
Деталь: | FRAME-REGI, ML-5015ND,SEC |
Парткод: | JC93-00385A |
Деталь: | FRAME-MIDDLE, ML-5015ND,ABS+PC,BLACK |
Парткод: | JC61-04281A |
Деталь: | HOLDER-SAW, ML-6510ND,PC,W216.8,L16,Black |
Парткод: | JC61-03906A |
Деталь: | ROLLER TR-FRAME-ROLLER TRANSFER UV, Petre |
Парткод: | JC93-00420A |
Деталь: | HOLDER-GND_TR, ML-6510ND,ABS+PC,W21.7,L19 |
Парткод: | JC61-03959B |
Деталь: | HOLDER-GEAR_TR, ML-6510ND,ABS+PC,W21.7,L1 |
Парткод: | JC61-03984B |
Деталь: | FRAME-RIGHT, ML-4510ND,XIC |
Парткод: | JC93-00367B |
Деталь: | FRAME-GUIDE CASSETTE RIGHT, ML-4510ND,XIC |
Парткод: | JC93-00361B |
Деталь: | DRIVE-FEED, ML-5015ND,SEC |
Парткод: | JC93-00350A |
Деталь: | SPRING-ES, SWP-B,PI0.35,D4.25,L33.8,ID3.9 |
Парткод: | 6107-001259 |
Деталь: | DRIVE FUSER-BRACKET, ML-5015ND,SEC |
Парткод: | JC93-00351A |
Деталь: | GUIDE-FUSER R, ML-5015ND,ABS+PET,GC-0700H |
Парткод: | JC61-04262A |
Деталь: | HOLDER-CONNECTOR SCF, ML-5015ND,ABS+PC,BL |
Парткод: | JC61-04242A |
Деталь: | HARNESS-SCF, ML-4510ND,UL10272,AWG26,UL10 |
Парткод: | JC39-01441A |
Деталь: | FOOT-HOLDER_LOWER, ML-6510ND,PC,BLACK |
Парткод: | JC61-03946A |
Деталь: | GEAR-RETARD IDLE B, ML-5015ND,POM,1.0,23, |
Парткод: | JC66-02886A |
Деталь: | GEAR-RETARD RDCN, ML-5015ND,POM,0.6 1.0, |
Парткод: | JC66-02885A |
Деталь: | FRAME-RIGHT, ML-5015ND,EGI-SECC,1 |
Парткод: | JC61-04285A |
Деталь: | GUIDE-CASSETTE R, ML-5015ND,ABS,BLACK,GUI |
Парткод: | JC61-04265A |
Деталь: | SWITCH-SIGNAL, Lever Type,PBT, POM, BsP,D |
Парткод: | JC34-00001A |
Деталь: | HARNESS-CST_JOINT, ML-4510ND,UL10272,AWG2 |
Парткод: | JC39-01440A |
Деталь: | BRACKET-GROUND CASSETTE, ML-5015ND,SECC,1 |
Парткод: | JC61-04289A |
Деталь: | RING-CS, ID2.8,OD8,T0.25,BLACK,SK-5 |
Парткод: | 6044-000001 |
Деталь: | LEVER-PICK_UP, ML-6510ND,POM,W66,L29.5,F2 |
Парткод: | JC66-02627A |
Деталь: | SPRING-ES, SWP,PI0.5,MD5.1,L30,ID4.4,OD5. |
Парткод: | 6107-001517 |
Деталь: | FRAME-PICK UP, ML-5015ND,SEC |
Парткод: | JC93-00383A |
Деталь: | PULLEY-DUPLEX, ML-5015ND,POM |
Парткод: | JC66-02902A |
Деталь: | ROLLER IDLE-DUPELX_DRIVE, ML-5015ND,EPDM, |
Парткод: | JC66-02966A |
Деталь: | HARNESS-DUP & UPLIMIT_SEN, ML-4510ND,UL1027 |
Парткод: | JC39-01443A |
Деталь: | HOLDER-PICK UP, ML-5015ND,PC+GF |
Парткод: | JC61-04255A |
Деталь: | ADJUST-DUPLEX OPEN, ML-5015ND,ABS,ICE GRE |
Парткод: | JC70-00598A |
Деталь: | PHOTO-INTERRUPTER, TR,BK |
Парткод: | 0604-001325 |
Деталь: | SPRING-CS, SWP B,0.5,17.5,4.7,5.7 |
Парткод: | 6107-002854 |
Деталь: | GROUND-DUPLEX BRACKET, ML-5015ND,STS,0.2, |
Парткод: | JC63-02982A |
Деталь: | BRUSH-PICK, ML-6510ND,SUS FIBER,35,71.7,N |
Парткод: | JC67-00468A |
Деталь: | GEAR-RETARD IDLE A, ML-5015ND,POM,0.6,29, |
Парткод: | JC66-02895A |
Деталь: | ACTUATOR-DUPLEX, ML-5015ND,POM,BLACK,ACTU |
Парткод: | JC66-02906A |

Деталь: | ADF-MEA UNIT-ROLLER PU, SCX-6345N/XRX,XER |
Парткод: | JC97-02259A |
Цена: | 240 ₽ |
Деталь: | MEA UNIT-IDLE FORWARD, SCX-6345N/XRX,XERO |
Парткод: | JC97-02292A |
Деталь: | GEAR-M_PU JOINT, SCX-6345N/XRX,POM,0.7,21 |
Парткод: | JC66-00943A |
Деталь: | HOUSING-PICKUP, ML-5015ND,PC |
Парткод: | JC61-04235A |
Деталь: | ACTUATOR-PAPER EMPTY, ML-5015ND,PC,BLACK, |
Парткод: | JC66-02905A |
Деталь: | GEAR-M_IDLE PU, SCX-6345N/XRX,POM,0.7,22, |
Парткод: | JC66-00940A |
Деталь: | HOLDER-ACTUATOR EMPTY, ML-5015ND,ABS |
Парткод: | JC61-04259A |
Деталь: | SPRING-TS, SUS304,0.5,6.2 |
Парткод: | 6107-002855 |
Деталь: | MEA UNIT-GEAR ONE WAY, SCX-6345N/XRX,XERO |
Парткод: | JC97-02291A |
Деталь: | CASSETTE, M4580,SEC |
Парткод: | JC90-01091B |
Деталь: | FRAME, M4530,SEE,220V |
Парткод: | JC93-00961C |
Деталь: | COVER-TOP, M4530ND |
Парткод: | JC95-01991A |
Деталь: | COVER-LEFT, M4580,HIPS,SPLIIT GRAY,S-834 |
Парткод: | JC63-04646A |
Деталь: | COVER-MP, M4530,ABS,340.18,SPLIT GRAY,CM- |
Парткод: | JC63-04648C |
Деталь: | COVER-LEFT NFC, M4580,HIPS,SPLIIT GRAY,S- |
Парткод: | JC63-04695A |
Деталь: | COVER-MAILBOX, M4530,ABS,SPLIT BROWN BLAC |
Парткод: | JC63-05081A |
Деталь: | MP SUB-TRAY, M4580,SEC |
Парткод: | JC90-01083B |
Деталь: | COVER-REAR, M4580,SEE |
Парткод: | JC95-01409B |
Деталь: | COVER-CASSETTE REAR, M4580,SEE |
Парткод: | JC95-01436B |
Деталь: | COVER-FRONT, M4580,SEE |
Парткод: | JC95-01948A |
Деталь: | COVER-RIGHT, M4530 |
Парткод: | JC95-01950B |
Деталь: | SENSOR-HUMIDITY, CHS-CSC-20,CLP-660,050C |
Парткод: | JC32-00005A |
Деталь: | PBA-MAIN, M4530ND,SEC,C4N,6L,MAIN PBA,155 |
Парткод: | JC92-02802A |
Деталь: | LSU, ML-5010ND,SEC,Single,A4(Ltr),600dpi, |
Парткод: | JC97-03877A |
Цена: | 4 800 ₽ |

Деталь: | FUSER, M4580,SEC,WORLD,220V |
Парткод: | JC91-01177A |
Цена: | 16 700 ₽ |
Деталь: | FAN-DC, CLX-8380ND/XAA,UL10272 AWG26,AMP |
Парткод: | JC31-00088A |

Деталь: | Резина ролика захвата бумаги |
Парткод: | CET7911 |
Деталь: | MP-UPPER, ML-5015ND,SEC |
Парткод: | JC90-01079A |
Деталь: | MP-LOWER, ML-5015ND,SEC |
Парткод: | JC90-01081A |
Деталь: | MP-PICK UP, ML-5015ND,SEC |
Парткод: | JC90-01080A |
Цена: | 2 400 ₽ |
Деталь: | GUIDE-M_DOC SENSOR, SCX-6320F,HIPS,2.5T,P |
Парткод: | JC61-00788A |
Деталь: | STOPPER-PAPER MP, ML-5015ND,PC |
Парткод: | JC61-04231A |
Деталь: | PHOTO-INTERRUPTER, TR,BK |
Парткод: | 0604-001325 |
Деталь: | FRAME-MP UPPER_SUB, ML-5015ND,ABS |
Парткод: | JC61-04233A |
Деталь: | MP-RETARD, ML-5015ND,SEC |
Парткод: | JC90-01082A |
Деталь: | FRAME-MP LOWER, ML-5015ND,PC |
Парткод: | JC61-04234A |
Деталь: | SLEEVE-MP, ML-2855ND,6,41.4,10 |
Парткод: | JC61-02808A |

Деталь: | ROLLER IDLE-RUBBER-PICK_UP, ML-2851ND,-,1 |
Парткод: | JC73-00295A |
Цена: | 380 ₽ |

Деталь: | ROLLER IDLE-RUBBER-TL, ML-6510ND,EPDM80%+ |
Парткод: | JC73-00328A |
Цена: | 430 ₽ |
Деталь: | COUPLER-TORQUE_LIMITER, ML-6510ND,NTR,290 |
Парткод: | JC67-00465A |
Деталь: | DRIVE-MAIN, M4580,SSDP |
Парткод: | JC93-00923A |
Деталь: | MOTOR BLDC-38W, M4580,3/10,38W,DC 24V,800 |
Парткод: | JC31-00075C |
Деталь: | CLUTCH-ELECTRIC, ML-4510ND,POM,2.5kgf.cm |
Парткод: | JC47-00033E |
Деталь: | GEAR-PICKUP PULLEY, ML-5015ND,POM,2.0, 0. |
Парткод: | JC66-02870A |
Деталь: | GEAR-FUSER RDCN A, ML-5015ND,POM,0.5, 0.8 |
Парткод: | JC66-02874A |
Деталь: | GEAR-DEVE IDLE, M4580,POM,0.4,67,BLACK,JI |
Парткод: | JC66-04153A |
Деталь: | BELT-TIMING GEAR, RUBBER,T1.36,L168MM,BLK |
Парткод: | 6602-001581 |
Деталь: | GEAR-OPC DRIVE, M4580,POM,0.4,115,BLACK,J |
Парткод: | JC66-04151A |
Деталь: | GEAR-DEVE RDCN, M4580,POM,0.4,73,BLACK,JI |
Парткод: | JC66-04154A |
Деталь: | GEAR-AGI IDLE B, ML-5015ND,POM,0.8, 0.8,4 |
Парткод: | JC66-02861A |
Деталь: | GEAR-AGI IDLE A, M4580,POM,0.4/0.8,63/22, |
Парткод: | JC66-04155A |
Деталь: | GEAR-AGI IDLE C, ML-5015ND,POM,0.8, 0.8,5 |
Парткод: | JC66-02862A |
Деталь: | GEAR-FEED RDCN, ML-5015ND,POM,0.8,28,24.0 |
Парткод: | JC66-02872A |
Деталь: | MOTOR DC, NF213G-1020515,DC24V,CLX-8380ND |
Парткод: | JC31-00078A |
Цена: | 1 600 ₽ |
Деталь: | MOTOR BLDC, DV 24V,2.0A,25W,ML-5015ND,TYP |
Парткод: | JC31-00144B |
Деталь: | FUSER-EXIT UPPER, ML-5010ND,SEC,EXP |
Парткод: | JC91-01043A |
Деталь: | FUSER-EXIT LOWER, ML-5010ND,SEC,EXP |
Парткод: | JC91-01040A |
Деталь: | FUSER-LEVER PRESSURE, ML-5010ND,SEC,EXP |
Парткод: | JC91-01045A |
Деталь: | GEAR-PR, ML-5010ND,PPS,1,33,37.32 |
Парткод: | JC66-02854A |
Деталь: | ROLLER FUSER-PRESSURE, M4580,24.5,STKM,1. |
Парткод: | JC66-02855B |
Деталь: | BRUSH-EXIT, ML-5010,SUS FIBER,0.9T,W6.2,L |
Парткод: | JC67-00528A |
Деталь: | FUSER-BELT, M4580,SEC,WORLD,220V |
Парткод: | JC91-01175A |
Деталь: | THERMISTOR-NTC ASSY, 7Kohm,3390K,0.3MWC |
Парткод: | 1404-001799 |
Деталь: | THERMOSTAT, AC125/250V,195+-5100 |
Парткод: | 4712-001085 |
Деталь: | HARNESS-FUSER_FU, M4580,UL3398,4,250,WHT, |
Парткод: | JC39-02125A |
Деталь: | FUSER-BIAS PRESSURE ROLLER, ML-5010ND,SEC |
Парткод: | JC91-01044A |
Деталь: | HOLDER-M-IDLE ROLLER, ML-2150,PC,BLK |
Парткод: | JC61-00785A |
Деталь: | ROLLER, ML-165,POM |
Парткод: | JC72-40981A |
Деталь: | SPRING-TS, SUS304,PI0.45,D3.85,L20,W10,ID |
Парткод: | 6107-001159 |
Цена: | 260 ₽ |
Деталь: | ROLLER-EXIT_F_UP, ML-6510ND,SILICON |
Парткод: | JC66-02973A |
Деталь: | ACTUATOR-EXIT, ML-5010ND,PA66,2T,20.1,125 |
Парткод: | JC66-02850A |
Деталь: | HOLDER-M_REAR_LEVER, SCX-5530FN,PC,t1.5,1 |
Парткод: | JC61-01625A |
Деталь: | BELT FUSER-DRUM, CLP-670ND,SUS,LSR,Non-co |
Парткод: | JC66-02037B |
Деталь: | LAMP-HALOGEN, 230V,1300W,266 |
Парткод: | 4713-001574 |
Деталь: | HANDLE-CASSETTE, M4580,HIPS,3,112.5,432,S |
Парткод: | JC64-00961A |
Деталь: | INDICATOR-PAPER, M4580,ABS,1.5,SPLIT GRAY |
Парткод: | JC64-00962A |
Деталь: | CSP-FRAME_GUIDE PAPER DUMMY, ML-4210ND,AB |
Парткод: | JC81-08737B |
Деталь: | CASSETTE FRAME, M4580,SEC |
Парткод: | JC90-01288A |
Деталь: | CSP-GEAR LIFTING, ML-6510ND,POM,F20-02 |
Парткод: | JC81-08478A |
Деталь: | GEAR-M_PINION 24, SCX-6345N/XRX,POM,1,24, |
Парткод: | JC66-01020A |
Деталь: | CSP-GEAR IDLE RETARD, ML-6510ND,POM,M90-4 |
Парткод: | JC81-08477A |
Деталь: | GEAR-PICKUP DRIVE, SCX-6555N,POM,1,25,NAT |
Парткод: | JC66-01676A |
Деталь: | CASSETTE-RETARD, ML-6510ND,XRX |
Парткод: | JC90-01049A |
Деталь: | PAD-MP(PLUS), SCX-5315F,Urethan Sponge,90 |
Парткод: | JC69-00494A |
Деталь: | CASSETTE SUB-GUIDE REAR PAPER, M4580,SEC |
Парткод: | JC90-01050F |
Деталь: | CASSETTE SUB-SIDE RIGHT, M4580,SEC |
Парткод: | JC90-01047D |
Деталь: | CASSETTE SUB-SIDE LEFT, M4580,SEC |
Парткод: | JC90-01048C |

Деталь: | ADF-MEA UNIT-ROLLER PU, SCX-6345N/XRX,XER |
Парткод: | JC97-02259A |
Цена: | 240 ₽ |
Деталь: | COVER-TOP, M4530ND |
Парткод: | JC95-01991A |
Деталь: | COVER-REAR DUMMY, M4530,ABS,SPLIT GRAY,CM |
Парткод: | JC63-05080A |
Деталь: | TRAY-ASF OUT, M4530,ABS,91.4,SPLIT BROWN |
Парткод: | JC63-05086A |
Деталь: | COVER-TOP 4LINE, M4530,ABS,SPLIT BROWN BL |
Парткод: | JC63-05082A |
Деталь: | COVER-USB, M4530,HIPS,SPLIT BROWN BLACK,H |
Парткод: | JC63-05084A |
Деталь: | HARNESS-DIRECT USB, M4530,UL2725,400,GRAY |
Парткод: | JC39-02361A |
Деталь: | LEVER-STACKING, ML-5015ND,PC,77,64.3,BLAC |
Парткод: | JC66-02904A |
Деталь: | DAMPER-LEVER STACKING, ML-5015ND,VHM-C 15 |
Парткод: | JC66-03030A |
Деталь: | PBA-OPE, M4530,SEC,FR1,3Array,197 X 100,4 |
Парткод: | JC92-02796A |
Деталь: | KEY-OPE PAD, M4530,SI,99.47,1.0,GRAY |
Парткод: | JC64-00997A |
Деталь: | KEY-STOP, CLP-680ND,ABS,14.15,SPLIT ORANG |
Парткод: | JC64-00813A |
Деталь: | KEY-POWER, CLP-680ND,ABS,13.36,1.5T,SPLIT |
Парткод: | JC64-00812A |
Деталь: | None |
Парткод: | JC64-01001A |
Деталь: | COVER-LCD 4LINE, M4530,PC,NATURAL (TRANSP |
Парткод: | JC63-05085A |
Деталь: | GROUND-LCD, M4530,STS304,0.2,45.6,69.2,GR |
Парткод: | JC63-05087A |
Деталь: | LCD, YMC12864-309BEEFDGN,ML-4510ND,128 |
Парткод: | JC07-00020A |
Деталь: | HARNESS-OPE GND, M4530,UL1007,225,GRAY/BL |
Парткод: | JC39-02362A |
Деталь: | HOLDER-LCD, CLX-4195FN,ABS,69.7,49.55,W94 |
Парткод: | JC61-05530A |
Деталь: | LENS-BACKLIGHT, CLX-4195FN,PC,64.54x44.32 |
Парткод: | JC67-00651A |
Деталь: | HARNESS-4LINE OPE, M4530,UL10272,230,GRAY |
Парткод: | JC39-02360A |
Деталь: | FRAME-UPPER, M4580,SEE |
Парткод: | JC93-00955A |
Деталь: | PBA-DEVE CRUM JOINT, CLX-9350,SEC,,FR-4 |
Парткод: | JC92-02163A |
Деталь: | PBA-ERASER, ML-4510ND,24V,PBA-ERASER,FR-1 |
Парткод: | JC92-02373A |
Деталь: | DUCT-MAIN DEVE, M4580,ABS,HF-0660I,BLACK |
Парткод: | JC67-00752A |
Деталь: | HOLDER-ERASER, ML-5015ND,PC |
Парткод: | JC61-04247A |
Деталь: | HOLDER-CONNECTOR DEVE, ML-5015ND,ABS,BLAC |
Парткод: | JC61-04243A |
Деталь: | FRAME-LEFT, ML-5015ND,SEC |
Парткод: | JC93-00364A |
Деталь: | FAN-DC, CLX-8380ND/XAA,UL10272 AWG26, AM |
Парткод: | JC31-00086A |
Деталь: | PHOTO-INTERRUPTER, TR,BK |
Парткод: | 0604-001325 |
Деталь: | GUIDE-FUSER L, ML-5015ND,ABS+PET,GC-0700H |
Парткод: | JC61-04261A |
Деталь: | FRAME-GUIDE CASSETTE LEFT, ML-5015ND,SEC |
Парткод: | JC93-00360A |
Деталь: | FRAME-TERMINAL FUSER, ML-5015ND,SEC |
Парткод: | JC93-00371A |
Коды ошибок
11-2T11, 11-2T21, 11-2T31
11-2T41, 11-2T51, 11-2T61
A1-1112, A1-1113
A1-1210, A1-2110
A1-2112, A1-2113
A1-2410, A1-2610
A1-5110
A3-3212
A3-3312, A3-3320
A4-1110
C1-1110, C1-111A
C1-1140, C1-1150, C1-1170
C1-1311, C1-1313, C1-1314
C1-1411
C1-1512
C1-1712
C3-1110
C3-1140, C3-1150, C3-1170
C3-1312
C3-1411, C3-1414
C3-1512
C3-1712
C6-1120
H1-1210, H1-1211
H1-1222
H1-1230
H1-1251, H1-1252, H1-1254
H1-1253
H1-1310, H1-1311
H1-1322
H1-1330
H1-1351, H1-1352, H1-1354
H1-1353
H1-1410, H1-1411
H1-1422
H1-1430
H1-1451, H1-1452, H1-1454
H1-1453
H1-1510, H1-1511
H1-1522
H1-1530
H1-1551, H1-1552, H1-1554
H1-1553
M1-1110
M1-1610
M1-3122
M1-4111
M1-5111, M1-5112, M1-5113
M1-5120
M1-5612
M2-1110, M2-1111
M2-1114, M2-1214
M2-2211, M2-2212
M2-2214, M2-2310
M3-1110, M3-1111, M3-1112
M3-2130
S1-2411
S1-2511
S2-1110
S2-331C, S2-331D, S2-3321
S2-4210
S2-4310
S6-3113
S6-3123
S6-3128
S6-3231
S6-3232
S6-3233
S6-3234
S6-3235
S6-3236
S7-2110
U1-2112, U1-2120, U1-2132
U1-2115, U1-2116
U1-2117
U1-2135, U1-23xx
U2-1111, U2-1112
U2-1113, U2-1114
Описание
Error code: | 11-2T11, 11-2T21, 11-2T31 |
Description: | Paper mismatch Tray X Paper mismatch MPT |
Causes: | Paper in tray is not matched to the machine paper setting. |
Remedy: | 1) Check and change the paper setting of the corresponding tray properly. |
Error code: | 11-2T41, 11-2T51, 11-2T61 |
Description: | Paper mismatch Tray X Paper mismatch MPT |
Causes: | Paper in tray is not matched to the machine paper setting. |
Remedy: | 1) Check and change the paper setting of the corresponding tray properly. |
Error code: | A1-1112, A1-1113 |
Description: | Motor Failure: #A1-1112. Turn off then on. Call for service if the problem persists Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists |
Causes: | Main(Feed/Fuser) motor operation is abnormal. • A1–1112 : Main motor is not operated for print-job. • A1–1113 : Main motor is operating but machine recognizes status as "Stopped". |
Remedy: | 1) Turn the machine off. Check if there are any foreign substances or paper around the paper path. 2) Remove the right cover. 3) Check if the main motor connector is connected correctly. 4) If the connection is OK, turn the machine on. Enter SVC mode. Select the main motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) Check the motor operation. a) If the motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the main(feed/fuser) motor. • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board. - If the control signal is abnormal, replace the main board. b) If the motor is operational, • Check the Pin No 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. 5) If the main motor operation is normal, remove the fuser unit. Check if the fuser unit has any problem. Replace the fuser unit. |
Error code: | A1-1210, A1-2110 |
Description: | Fan Failure: #A2-xxxx. Tum off then on. Call for service if the problem ~rsists |
Causes: | SMPS or Fuser or LSU or Deve fan is not operational. |
Remedy: | 1) Tum the machine off. 2) Check if the corresponding fan connector is connected coll`ectly. 3) If the connection is OK, Enter SVC mode and execute fan test. 4) If the fan is not operational, measure the fan power. a) If 24V power is generated, replace the defective fan. SMPS fan: JC31--00153A • Main(Fuser) fan : JC31- 00088A • LSU fan : JC31- 00086A • Deve fan : JC31–00086A b) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00092C (220V) / JC44-00091C (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92–02802A(M4530ND) / JC92–02801A(M4530NX)). 5) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. b) Check fan operation as connected or disconnected. • If the Lock signal is 0V continually, check the harness. If the harness is OK, replace the main board. • If the signal value is different from the table above, replace the fan. |
Error code: | A1-2112, A1-2113 |
Description: | Motor Failure: #A1-1112. Turn off then on. Call for service if the problem persists Motor Failure: #A1-1113. Turn off then on. Call for service if the problem persists |
Causes: | OPC/Deve motor operation is abnormal. • A1–2112 : OPC/Deve motor is not operated for print-job. • A1–2113 : OPC/Deve motor is operating but machine recognizes status as "Stopped". |
Remedy: | 1) Turn the machine off. Check if there are any foreign substances or paper around the paper path. 2) Remove the right cover. 3) Check if the OPC/Deve motor connector is connected correctly. 4) If the connection is OK, turn the machine on. Enter SVC mode. Select the OPC/Deve motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) Check the motor operation. a) If the OPC/Deve motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the OPC/Deve motor. • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board. - If the control signal is abnormal, replace the main board. b) If the OPC/Deve motor is operational, • Check the Pin No 8. If the value is abnormal, replace the main board. If the value is normal, replace the harness. 5) If the OPC/Deve motor operation is normal, remove the imaging unit. Check if the imaging unit has any problem. Replace the imaging unit. |
Error code: | A1-2410, A1-2610 |
Description: | Fan Failure: #A2-xxxx. Tum off then on. Call for service if the problem ~rsists |
Causes: | SMPS or Fuser or LSU or Deve fan is not operational. |
Remedy: | 1) Tum the machine off. 2) Check if the corresponding fan connector is connected coll`ectly. 3) If the connection is OK, Enter SVC mode and execute fan test. 4) If the fan is not operational, measure the fan power. a) If 24V power is generated, replace the defective fan. SMPS fan: JC31--00153A • Main(Fuser) fan : JC31- 00088A • LSU fan : JC31- 00086A • Deve fan : JC31–00086A b) If 24V power is not generated, • Measure the 24V power on the SMPS board. If the SMPS board(JC44-00092C (220V) / JC44-00091C (110V)) is defective, replace it. • If the SMPS board is normal, replace the main board(JC92–02802A(M4530ND) / JC92–02801A(M4530NX)). 5) If the fan operation is normal but the error persists, a) Check the yellow line signal with DVM. b) Check fan operation as connected or disconnected. • If the Lock signal is 0V continually, check the harness. If the harness is OK, replace the main board. • If the signal value is different from the table above, replace the fan. |
Error code: | A1-5110 |
Display: | Motor Failure: #A1-5110. Turn off then on. Call for service if the problem persists |
Description: | Supply motor operation is abnormal. |
Causes: | Supply motor operation is abnormal. |
Remedy: | 1) Turn the machine off. 2) Remove the right cover. 3) Check if the DC motor (toner supply motor) connector in the main drive unit is connected correctly. 4) If the connection is OK, turn the machine on. Enter SVC mode. Select the DC motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines) Check the motor operation. a) If the DC motor is not operational, • Check the signal and power with the DVM. • If the checked result is normal, replace the DC motor(JC31-00078A) or the main drive unit(JC93–00923A). • If the checked result is abnormal, check the following. - If 24V power is not generated, replace the SMPS board(JC44-00092C (220V) / JC44-00091C (110V)). - If the control signal is abnormal, replace the main board(JC92–02722A). b) If the DC motor is operational, • If the value on the main board is abnormal, replace the main board. If the value is normal, replace the harness. |
Error code: | A3-3212 |
Description: | Sensor Failure: #A3-3212. Turn off then on. Call for service if the problem persists |
Causes: | Inner temperature sensor is defective. |
Remedy: | 1) Enter SVC mode. Execute sensor test to check its operation. (Diagnostics > Engine Diagnostics > Engine Test Routines) 2) Measure the resistance value of the connector at both ends. If the value is not in 47.5KΩ ~ 52.5KΩ (@ 25 ℃), replace the inner temp sensor. 3) If the sensor is normal, replace the main board. |
Error code: | A3-3312, A3-3320 |
Description: | Sensor Failure: #A3-3312. Turn off then on. Call for service if the problem persists The room temperature is not suitable for this set use. Please adjust room temperature |
Causes: | Outer temperature/humidity sensor is defective. |
Remedy: | 1) Enter SVC mode. Execute sensor test to check its operation. (Diagnostics > Engine Diagnostics > Engine Test Routines > Outer Temperature) 2) Measure the resistance value of the connector at both ends. If the value is not in 47.5KΩ ~ 52.5KΩ (@ 25 ℃), replace the outer temperature/humidity sensor. 3) If the harness and sensor are normal, replace the main board. |
Error code: | A4-1110 |
Display: | Lamp Failure: #A4-1110. Open the door, then close it. Call for service if the problem persists |
Description: | Erase Lamp does not turn on. |
Causes: | Erase Lamp does not turn on. |
Remedy: | 1) Enter SVC mode. Execute the erase lamp test. (Diagnostics > Engine Diagnostics > Engine Test Routines > Erase Lamp) 2) If the erase lamp does not turn on, replace it(JC92-02373A). |
Error code: | C1-1110, C1-111A |
Display: | C1-1110, C1-111A Toner error |
Description: | Prepare new yellow toner cartridge. Shake toner cartridge and then install. Replace toner cartridge if the problem persists |
Causes: | Toner remained is 5 ~ 30% of its life. |
Remedy: | 1) Order new yellow toner cartridge because toner cartridge with level of “Low” will be exhausted soon. |
Error code: | C1-1140, C1-1150, C1-1170 |
Description: | Replace with new toner cartridge. End of life, Replace with new toner cartridge. |
Causes: | Toner cartridge is at the end of its life. |
Remedy: | 1) Open the front cover. 2) Remove the toner cartridge. 3) Install the new toner cartridge. 4) Close the front cover. |
Error code: | C1-1311, C1-1313, C1-1314 |
Description: | Toner Cartridge Failure: #C1-1311. Install toner cartridge again Shake toner cartridge and then install. Call for service if the problem persists Did not supply enough toner. Remove seal tape of toner cartridge or shake it. Call for service if the problem persists |
Causes: | Toner supply is inefficient or abnormal. |
Remedy: | 1) Turn the machine off. Open the front cover 2) Remove the toner cartridge. Shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge. 3) If the problem persists, check the follows. a) Check if the Toner Supply Drive Unit(JC93–00436A) is defective. b) Check if the Toner Duct Drive Unit(JC93–00451A) is defective. 4) If the problem persists, replace the toner cartridge. 5) If the problem persists, replace the drum unit. |
Error code: | C1-1411 |
Display: | Toner cartridge is not installed. Install it. |
Description: | Toner cartridge is not installed. Install the cartridge |
Causes: | The toner cartridge is not installed. / The machine can’t detect the toner cartridge. |
Remedy: | 1) Turn the machine off then on. 2) Remove the toner cartridge. Thoroughly roll the cartridge five or six times to distribute the toner evenly inside the cartridge. And reinstall the toner cartridge. 3) Check if the CRUM contact area is contaminated. Clean it. |
Error code: | C1-1512 |
Display: | Toner cartridge is not compatible. Check users guide. |
Description: | Toner cartridge is not compatible. Check users guide. |
Causes: | Toner cartridge is not compatible. |
Remedy: | 1) Print the supply information report. Check information of the toner cartridge. 2) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
Error code: | C1-1712 |
Display: | Error: #C1-1712 / Toner Cart Failure: #C1-1712. Call for service |
Description: | The machine can’t detect the CRUM chip of the toner cartridge. |
Causes: | The data of CRUM is not detected. / CRUM is defective. |
Remedy: | These errors are for M3375/3875/4075. 1) Open the front cover. 2) Remove the toner cartridge. 3) Check if the CRUM terminal is contaminated. Clean it. 4) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one. |
Error code: | C3-1110 |
Display: | Prepare IMG. Unit / Prepare new imaging unit Replace IMG. Unit / Replace with new imaging unit |
Description: | The remaining imaging unit is less than 10% / The imaging unit is at the end of its life. |
Causes: | Imaging unit has almost reached the end of its life. |
Remedy: | These errors are for M3325/3825/4025. Check the life remaining of the imaging unit. If its life is at the end, turn the machine off and replace the imaging unit with new one. |
Error code: | C3-1140, C3-1150, C3-1170 |
Display: | C3-1140, C3-1150, C3-1170 Imaging unit errors |
Description: | Replace with new imaging unit End of life, Replace with new imaging unit. |
Causes: | Imaging unit is at the end of its life. |
Remedy: | 1) Open the front cover. 2) Remove the imaging unit and replace it with new one. 3) Close the front cover. |
Error code: | C3-1312 |
Display: | Imaging Unit Failure: #C3-1312. Install imaging unit again. |
Description: | Imaging Unit Failure: #C3-1312. Install imaging unit again |
Causes: | Toner supply is inefficient or abnormal. |
Remedy: | 1) Turn the machine off. Open the front cover 2) Remove the toner cartridge. Shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge. 3) If the problem persists, check the follows. a) Check if the Toner Supply Drive Unit(JC93–00436A) is defective. b) Check if the Toner Duct Drive Unit(JC93–00451A) is defective. 4) If the problem persists, replace the toner cartridge. 5) If the problem persists, replace the drum unit. |
Error code: | C3-1411, C3-1414 |
Description: | Imaging unit is not installed. Install the unit Imaging Unit Failure: #C3-1414. Install imaging unit again. |
Causes: | The imaging unit is not installed properly. |
Remedy: | 1) Open the front cover. 2) If the imaging unit is not installed, install it. Try to test the machine again. 3) If the imaging unit is installed, remove it. Check if the modular jack is contaminated or broken. 4) Clean the modular jack or replace the imaging unit. 5) If it is OK, check the CN22 harness connection on the main board. 6) If the harness is defective, replace it. 7) Turn the machine off then on. Try to test the machine. |
Error code: | C3-1512 |
Display: | Imaging unit is not compatible. Check user`s guide |
Description: | Imaging unit is not compatible. Check the user guide |
Causes: | Imaging unit is not compatible. |
Remedy: | 1) Open the front cover. Remove the imaging unit. 2) Check if the label information of the imaging unit is same with the machine’s one. (ex. /SEE) 3) If label information is different from the machine or the imaging unit is not a samsung genuine, replace it with a new one. |
Error code: | C3-1712 |
Description: | Imaging unit Failure: #C3-1712. Call for service. |
Causes: | The data of CRUM is not detected. |
Remedy: | 1) Open the front cover. 2) Remove the imaging unit check that its modular jack is contaminated or deformed. 3) If it is defective, replace it with new one. 4) Close the front cover. |
Error code: | C6-1120 |
Display: | Replace new Fuser unit |
Description: | Replace with new fuser unit |
Causes: | The life of the fuser unit has expired. |
Remedy: | 1) Turn the machine off. 2) Replace the fuser unit(JC91-01157A (220V) /JC91-01158A (110V)). 3) Turn the machine on. |
Error code: | H1-1210, H1-1211 |
Display: | Paper jam in Tray 2. |
Description: | Paper jam has occurred in tray2. |
Causes: | Paper jam has occurred in tray2. |
Remedy: | 1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray2 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray2 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray2 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 6) Check if the AS-SPRING_ES is deformed or assembled properly. 7) If the problem persists after checking No. 1-7, replace the SCF board(JC92-02754A). 8) If the problem persists, replace the Drop connector harness. |
Error code: | H1-1222 |
Display: | Pulled Out Tray2 Cassette |
Description: | The option tray is not inserted perfectly. |
Causes: | Tray 2 is pulled out or the cassette detection sensor connector is not connected or broken. |
Remedy: | 1. Remove and re-install the option tray. |
Error code: | H1-1230 |
Display: | Error: #H1-1230 / Input System Failure: #H1-1230. Check tray 2 connection |
Description: | Communication error has occurred. |
Causes: | The communication error between the tray 2 and the main machine has occurred. |
Remedy: | 1) Turn the machine off then on. 2) If the problem persists, turn the machine off. 3) Remove the SCF right cover. (Refer to 3.3.23.1) 4) Check if the interface connector is connected to the SCF main board. If the interface connector is defective, replace it. 5) If the problem persists, replace the SCF main board.(JC92-02636A) |
Error code: | H1-1251, H1-1252, H1-1254 |
Display: | Paper is low in Tray 2. Load paper. Paper is empty in tray 2. Load paper. |
Description: | Paper in the tray2 is less than 10% of specification. / The photo sensor is defective. |
Causes: | Paper in the tray2 is less than 10% of specification. / The photo sensor is defective. |
Remedy: | 1) Remove tray2. Load the paper in tray2. 2) If paper is loaded but error message has not disappeared, check the following. a) Check if the paper empty sensor is contaminated. If so, clean it. b) If the paper empty sensor(0604-001325) is defective, replace it. c) If the empty actuator(JC66–02613A) is defective, replace it. |
Error code: | H1-1253 |
Display: | Input System Failure #H1-1253 : Pull Tray 2 out and insert it. |
Description: | The paper is not fed from tray2. |
Causes: | The paper is not fed from tray2. |
Remedy: | 1) Check if the Gear-Idle Lift is broken. 2) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 3) If the connection is OK, replace the cassette detection sensor(JC34-00001A). 4) Check if the Lift-Motor connector is connected properly. 5) If the problem persists, replace the Lift-Motor(JC81-08705A). |
Error code: | H1-1310, H1-1311 |
Display: | Paper jam in Tray 3. |
Description: | Paper jam has occurred in tray3. |
Causes: | Paper jam has occurred in tray3. |
Remedy: | 1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray3 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray2 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray3 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 7) If the problem persists after checking No. 1-7, replace the SCF board(JC92-02754A). 8) If the problem persists, replace the Drop connector harness. |
Error code: | H1-1322 |
Display: | Tray 3 cassette is pulled out. Insert it properly. |
Description: | Tray 3 cassette is pulled out. Insert it properly. |
Causes: | Tray 3 is pulled out or the auto size sensor connector is not connected or broken. |
Remedy: | 1) Remove and insert tray3 correctly. 2) If the problem persists, remove tray3 and tray4. Look inside machine. 3) Check if the auto size sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the auto size sensor(JC93-00018A). 5) If the problem persists, replace the DCF board(JC92-02453A). |
Error code: | H1-1330 |
Description: | Input System Failure: #H1-1330. Check tray 3 connection. |
Causes: | The communication error between the tray 3 and the main machine has occurred. |
Remedy: | 1) Turn the machine off. 2) Check the connection on SCF board. Reconnect the harness. 3) If the drawer connector is deformed or broken, replace it. (AS-HARNESS HSCF : JC81–09742A / HOLDER-CONNECTOR_SCF : JC61–01742A)) 4) If the problem persists, replace the SCF main board(JC92-02754A). |
Error code: | H1-1351, H1-1352, H1-1354 |
Display: | Paper is low in Tray 3. Load paper. Paper is empty in tray 3. Load paper. |
Description: | Paper is low in Tray 3. Load paper. Paper is empty in Tray 3. Load paper. |
Causes: | Paper in the tray is less than 10% of specification. / The photo sensor is defective. |
Remedy: | 1) Remove tray3. Load the paper in tray3. 2) If paper is loaded but error message has not disappeared, check the following. a) Remove the DCF pick up unit1. b) Check if the photo sensor in the DCF pick up unit1 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. d) If the actuator(JC66-03199A) is defective, replace it. |
Error code: | H1-1353 |
Display: | Input System Failure #H1-1353 : Pull Tray 3 out and insert it. |
Description: | Input System Failure #H1-1353 : Pull Tray 3 out and insert it. |
Causes: | The paper is not fed from tray3. |
Remedy: | 1) Remove and insert tray3 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit1. b) Check if the photo sensor in the DCF pick up unit1 is contaminated, clean it. c) If the photo sensor(0604-001393) is defective, replace it. |
Error code: | H1-1410, H1-1411 |
Display: | Paper jam in Tray 4. |
Description: | Paper jam has occurred in tray4. |
Causes: | Paper jam has occurred in tray4. |
Remedy: | 1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray4 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray2 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray4 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 6) Check if the AS-SPRING_ES is deformed or assembled properly. 7) Check if the Press D-cut of the Gear-Lifting(JC81-08478A) is broken. 8) If the problem persists after checking No. 1-7, replace the SCF board(JC92-02754A). 9) If the problem persists, replace the Drop connector harness. |
Error code: | H1-1422 |
Display: | Tray 4 cassette is pulled out. Insert it properly. |
Description: | Tray 4 cassette is pulled out. Insert it properly. |
Causes: | Tray 4 is pulled out or the auto size sensor connector is not connected or is broken. |
Remedy: | 1) Remove and insert tray4 correctly. 2) If the problem persists, remove tray3 and tray4. Look inside machine. 3) Check if the auto size sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the auto size sensor(JC93-00018A). 5) If the problem persists, replace the DCF board(JC92-02453A). |
Error code: | H1-1430 |
Description: | Input System Failure: #H1-1430. Check tray 4 connection. |
Causes: | The communication error between the tray 4 and the main machine has occurred. |
Remedy: | 1) Turn the machine off. 2) Check the connection on SCF board. Reconnect the harness. 3) If the drawer connector is deformed or broken, replace it. (AS-HARNESS HSCF : JC81–09742A / HOLDER-CONNECTOR_SCF : JC61–01742A)) 4) If the problem persists, replace the SCF main board(JC92-02754A). |
Error code: | H1-1451, H1-1452, H1-1454 |
Display: | Paper is low in Tray 4. Load paper. Paper is empty in tray 4. Load paper. |
Description: | Paper is low in Tray 4. Load paper. Paper is empty in Tray 4. Load paper. |
Causes: | Paper in tray4 is less than 10%. / The photo sensor is defective. |
Remedy: | 1) Remove tray4. Load the paper in tray4. 2) If paper is loaded but error message has not disappeared, check the following. a) Remove the DCF pick up unit2. b) Check if the photo sensor in the DCF pick up unit2 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. d) If the actuator(JC66-03199A) is defective, replace it. |
Error code: | H1-1453 |
Display: | Input System Failure #H1-1453 : Pull Tray 4 out and insert it. |
Description: | Input System Failure #H1-1453 : Pull Tray 4 out and insert it. |
Causes: | The paper is not fed from tray4. |
Remedy: | 1) Remove and insert tray4 correctly. 2) Turn the machine off then on. 3) If the problem persists, turn the machine off. 4) Remove the Bracket Rear Cover after removing 5 screws. 5) Check if the connection between the DCF pick up drive and DCF board is correct. 6) If the connection is OK, replace the pick up drive unit(JC93-00442A). 7) If the problem persists, check the following. a) Remove the DCF pick up unit2. b) Check if the photo sensor in the DCF pick up unit2 is contaminated. If so, clean it. c) If the photo sensor(0604-001393) is defective, replace it. |
Error code: | H1-1510, H1-1511 |
Description: | Paper jam in Tray 5. |
Causes: | Paper jam has occurred in tray5. |
Remedy: | 1) Remove the jammed paper. If the problem persists, check the followings. 2) Check if the paper is loaded in the tray5 properly. 3) Check if the pick up/forward/reverse rollers(JC97–02259A) of the tray5 are defective or worn out. 4) Check if the Empty/ Pick up/ Regi-Act sensor of the tray4 is working properly. 5) Check the connection between the motor/clutch and the SCF board. Reconnect the harness. 6) Check if the AS-SPRING_ES is deformed or assembled properly. 7) Check if the Press D-cut of the Gear-Lifting(JC81-08478A) is broken. 8) If the problem persists after checking No. 1~7, replace the SCF board(JC92-02754A). 9) If the problem persists, replace the Drop connector harness. |
Error code: | H1-1522 |
Description: | Tray 5 cassette is pulled out. Insert it properly. |
Causes: | Tray 5 is pulled out or the cassette detection sensor connector is not connected or broken. |
Remedy: | 1) Remove and insert tray5 correctly. 2) If the problem persists, remove tray5 again. 3) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 4) If the connection is OK, replace the cassette detection sensor(JC34-00001A). 5) If the problem persists, replace the SCF board(JC92-02754A). |
Error code: | H1-1530 |
Description: | Input System Failure: #H1-1530. Check tray 5 connection. |
Causes: | The communication error between the tray 5 and the main machine has occurred. |
Remedy: | 1) Turn the machine off. 2) Check the connection on SCF board. Reconnect the harness. 3) If the drawer connector is deformed or broken, replace it. (AS-HARNESS HSCF : JC81–09742A / HOLDER-CONNECTOR_SCF : JC61–01742A)) 4) If the problem persists, replace the SCF main board(JC92-02754A). |
Error code: | H1-1551, H1-1552, H1-1554 |
Description: | Paper is low in Tray 5. Load paper. Paper is empty in tray 5. Load paper. |
Causes: | Paper in the tray5 is less than 10% of specification. / The photo sensor is defective. |
Remedy: | 1) Remove tray5. Load the paper in tray5. 2) If paper is loaded but error message has not disappeared, check the following. a) Check if the paper empty sensor is contaminated. If so, clean it. b) If the paper empty sensor(0604-001325) is defective, replace it. c) If the empty actuator(JC66–02613A) is defective, replace it. |
Error code: | H1-1553 |
Description: | Input System Failure #H1-1553 : Pull Tray 5 out and insert it. |
Causes: | The paper is not fed from tray5. |
Remedy: | 1) Check if the Gear-Idle Lift is broken. 2) Check if the cassette detection sensor cable is connected correctly. Unplug and reconnect it. 3) If the connection is OK, replace the cassette detection sensor(JC34-00001A). 4) Check if the Lift-Motor connector is connected properly. 5) If the problem persists, replace the Lift-Motor(JC81-08705A). |
Error code: | M1-1110 |
Display: | Paper Jam in Tray1. |
Description: | Paper jam in tray 1. Please remove the paper |
Causes: | The jammed paper has occurred in the tray. |
Remedy: | 1) Clear the jam from the tray1. 2) Remove the tray. Check if the loaded paper is in proper place. Align it. 3) If the jammed paper occurred before entering it to the separation roller, check the Sheet Retard / Pickup roller / Forward roller / CST Knock up / CST Knock up Spring. 4) If the jammed paper occurred after entering it to the separation roller, check the Ribs in paper path. |
Error code: | M1-1610 |
Display: | Paper jam in MP Tray. |
Description: | Paper Jamin MP tray |
Causes: | The jammed paper has occurred in the MP tray. |
Remedy: | 1) Remove the jammed paper. 2) If the jammed paper occurs continually, check the followings. a) Check if the pick up/forward/reverse roller are worn out or contaminated. Clean the contaminated part or replace it. b) Check if the actuator is assembled correctly. 3) If the pick up clutch is defective, replace it. 4) If the problem persists, replace the MP unit. |
Error code: | M1-3122 |
Display: | Tray 1 cassette is pulled out. Insert it properly. |
Description: | Tray 1 cassette is pulled out. Insert it properly. |
Causes: | Tray 1 is pulled out or the auto size sensor connector is not connected or broken. |
Remedy: | 1) Remove and insert Tray1 correctly. 2) If Tray1 is not locked or pulled out without holding the locking lever, remove Tray1. 3) Check if foreign substance or paper is inside the space between Tray1,2. If so, please remove it. 4) If the problem persists, check that the auto size sensor is connected properly. 5) If the problem persists, replace the main board(JC92–02452A). |
Error code: | M1-4111 |
Display: | Input System Failure #M1-4111 : Pull Tray 1 out and insert it. |
Description: | Input System Failure #M1–4111 : Pull Tray 1 out and insert it. |
Causes: | The paper is not fed from tray1. |
Remedy: | 1) Remove tray1 and re-install it. 2) If the problem persists, turn the machine off then on. 3) Enter SVC mode. Execute pickup motor test. (Diagnostics > Engine Diagnostics > Engine Test Routines > 100-0370) 4) If the pick up motor operation is abnormal, turn the machine off. 5) Remove the rear cover. 6) Check if the connection between pickup drive unit1 and main board is secure. 7) If the connection is OK, replace the pickup drive unit(JC93-00442A). 8) If the problem persists, check the pickup unit1. a) Check if the photo sensor in the pickup unit1 is defective. b) If the sensor(0604–001393) is defective, replace it. |
Error code: | M1-5111, M1-5112, M1-5113 |
Description: | Paper is low in tray 1. Load paper Paper is empty in tray 1. Load paper. |
Causes: | Paper is low (M1–5111) or empty(M1–5112, M1–5113) in Tray1. |
Remedy: | 1) Check if the paper is loaded in tray1. Load the paper. 2) Check if the empty actuator(JC66-02905A) of the pick up Assy is assembled correctly. If it is broken or deformed, replace it. 3) Check if the empty sensor is connected correctly. If the harness is defective, replace it. 4) Check if the empty sensor(0604-001325) is defective, if so replace it. |
Error code: | M1-5120 |
Display: | Paper empty in tray 1 / Paper is empty in tray 1. Load paper All Tray Empty / Paper is empty in all tray. Load paper |
Description: | There is no paper in the tray1. / Actuator-Paper Empty or photo sensor is defective. |
Causes: | Paper is empty in all tray. |
Remedy: | 1) Load the paper in the tray1. If the problem persists, check the followings after turning the machine off. 2) If the Actuator-Paper Empty(JC66-02762A) is defective, replace it. (Refer to 3.3.21) 3) If the photo sensor(0604-001393) is defective, replace it. Check if the connector is connected properly. 4) If the problem persists, replace the main board. |
Error code: | M1-5612 |
Display: | Paper is empty in MP Tray. Load paper. |
Description: | Paper is empty in MP Tray. Load paper. |
Causes: | Paper in the MP tray is less than 10%. / The photo sensor is defective. |
Remedy: | 1) Load the paper in the MP tray. 2) If paper is loaded but error message has not disappeared, check the following : a) If the photo sensor is contaminated, clean it. b) If the photo sensor is defective, replace it(0604–001393). c) If the actuator is defective, replace it(JC66-03217A). |
Error code: | M2-1110, M2-1111 |
Description: | Paper jam in tray. Paper jam inside of machine. |
Causes: | The paper has jammed at the feed sensor. |
Remedy: | 1) Remove the tray1. Remove the jammed paper. And install the tray. 2) If the problem persists, check the followings. 3) Check if the feed sensor connector is connected correctly. 4) Check if the regi. roller is contaminated or worn out. 5) Check the regi. clutch connection. If the regi. clutch(JC47-00033E) is defective, replace it. 6) Check the pick up clutch connection. If the pick up clutch(JC47-00033E) is defective, replace it. |
Error code: | M2-1114, M2-1214 |
Description: | Paper jam in tray. Paper jam inside of machine. |
Causes: | The paper has jammed at the feed sensor. |
Remedy: | 1) Remove the tray1. Remove the jammed paper. And install the tray. 2) If the problem persists, check the followings. 3) Check if the feed sensor connector is connected correctly. 4) Check if the regi. roller is contaminated or worn out. 5) Check the regi. clutch connection. If the regi. clutch(JC47-00033E) is defective, replace it. 6) Check the pick up clutch connection. If the pick up clutch(JC47-00033E) is defective, replace it. |
Error code: | M2-2211, M2-2212 |
Description: | Paper jam inside of duplex path Paper jam at the top of duplex path Paper jam at the bottom of duplex path |
Causes: | The paper did not enter the duplex path and has jammed. |
Remedy: | 1) Remove the jammed paper. If the same error occurs continually, check the following. 2) Check if there are any obstacles or contamination in the duplex path. 3) Check if the exit actuator(JC66-02850A) of the fuser unit works normally. 4) Check if the exit motor works normally and its connector is connected properly. 5) If the exit motor is defective, replace it or exit drive unit(JC93-00349A). 6) Check if the duplex clutch works normally and its connector is connected properly. 7) If the duplex clutch(JC47-00033E) is defective, replace it. |
Error code: | M2-2214, M2-2310 |
Description: | Paper jam inside of duplex path Paper jam at the top of duplex path Paper jam at the bottom of duplex path |
Causes: | The paper did not enter the duplex path and has jammed. |
Remedy: | 1) Remove the jammed paper. If the same error occurs continually, check the following. 2) Check if there are any obstacles or contamination in the duplex path. 3) Check if the exit actuator(JC66-02850A) of the fuser unit works normally. 4) Check if the exit motor works normally and its connector is connected properly. 5) If the exit motor is defective, replace it or exit drive unit(JC93-00349A). 6) Check if the duplex clutch works normally and its connector is connected properly. 7) If the duplex clutch(JC47-00033E) is defective, replace it. |
Error code: | M3-1110, M3-1111, M3-1112 |
Description: | Paper jam in exit area. Paper jam inside of machine |
Causes: | Paper jam has occurred around the exit area. |
Remedy: | 1) Remove the jammed paper. If the same error occurs continually, check the following. 2) Check if there are any obstacles or contamination in the duplex path. 3) Check if the exit actuator(JC66-02850A) of the fuser unit works normally. 4) Check if the exit motor works normally and its connector is connected properly. 5) If the exit motor is defective, replace it or exit drive unit(JC93-00349A). 6) Remove the exit drive unit. Check if the gear is worn out or broken. If necessary, replace the exit drive unit. 7) Remove the fuser unit. If there is any broken or defective part of the fuser unit. Replace it or fuser unit(JC91–01177A (220V) / JC91–01176A (110V)). |
Error code: | M3-2130 |
Display: | Output bin full Remove paper |
Description: | Paper in output bin is full. Remove printed paper |
Causes: | The machine detected that the output tray has got full or the bin-full sensor is defective. |
Remedy: | 1) Remove the paper on the output tray. (The maximum loading capacity is 150 sheets based on standard paper (80 g/m²).) 2) Check if the Bin-full Sensor connector is connected properly. Reconnect it or replace the Bin-full sensor. |
Error code: | S1-2411 |
Display: | Error #S1-2411 Turn off then on. |
Description: | A communication error failure has occurred at HDD of main controller. |
Causes: | Hard Disk is not installed in the machine. / Hard Disk is defective. |
Remedy: | 1. Format the hard disk. 2. If the problem persists, replace the hard disk. |
Error code: | S1-2511 |
Description: | Error: #S1-2511 / MSOK System Failure: #S1-2511.Call for service |
Causes: | MSOK is not installed properly. / MSOK is defective. |
Remedy: | 1) Turn the machine off then on. If the problem persists, check the followings. 2) Check if the MSOK is inserted correctly. Remove and reinstall it. 3) If the problem persists, replace the main board. |
Error code: | S2-1110 |
Description: | Engine Failure: #S2-1110. Call for service if the problem persists |
Causes: | The CPU in main board has some problem. (Booting error, Communication error etc.) |
Remedy: | 1) Turn the machine off then on. 2) If the problem persists, replace the main board. |
Error code: | S2-331C, S2-331D, S2-3321 |
Description: | Calibrating... Please Wait Wait delay time for lower fixing temperature… Supplying and mixing toner to developer unit. Please wait... |
Causes: | These errors show the engine status. |
Remedy: | 1) Please wait until this error will disappear. |
Error code: | S2-4210 |
Display: | Front door is open. Close it. |
Description: | Front door is open. Close it. |
Causes: | Front cover or Side cover is opened. |
Remedy: | 1) Close the front cover correctly. 2) Check if the cover open sensor connector is connected properly. Reconnect it. 3) If the sensor is defective, replace it. |
Error code: | S2-4310 |
Description: | Rear door is open. Close the door |
Causes: | Rear cover is opened. |
Remedy: | 1) Open the rear cover and close it correctly. 2) Open the rear cover. 3) Check if the switch contact of the rear cover is deformed. 4) Remove the left cover. 5) Check the connection between the cover open sensor and HVPS board. Reconnect the harness. If the harness is defective, replace it. 6) Open the rear cover. Check if the message is changed when pushing the micro switch(cover open sensor). 7) If the cover open sensor is defective, replace it. |
Error code: | S6-3113 |
Description: | Network Failure: #S6-3113. Turn off then on. Call for service if the problem persists |
Causes: | Network PHY chip is defective. |
Remedy: | 1) Replace the main board. |
Error code: | S6-3123 |
Display: | This IP address conflicts with that of other system. Check it. |
Description: | This IP address conflicts with that of other system. Check it. |
Causes: | Network has some problem. (IP address conflicts with that of other system. / Communication error / There is no response when checking the ping test.) |
Remedy: | Change the machine’s IP address. • Execute the Samsung Easy Printer Manager program. (Device setting > Network > IP address). Change the IP address. • In case of DHCP or Bootp, reboot the machine to receive a new IP address. |
Error code: | S6-3128 |
Display: | 802.1x authentication failed. Please Contact the System Administrator |
Description: | There is no response when checking the ping test. ID or Password is incorrect. |
Causes: | Network error. ( A authenticator(eg switch) rejected authentication. / There is no response when checking the ping test.) |
Remedy: | 1) Change the IP adredd (Machine Setup > Network Setting > Login > TCP/IP > Select the network protocol > IP Setting 2) Inut the Network Login ID and Password correctly. |
Error code: | S6-3231 |
Description: | Can not find a wireless network. Please check the wireless environment |
Causes: | The machine can not find the SSID(Service Set Identifier). |
Remedy: | 1) Check the setting-up for wireless network. |
Error code: | S6-3232 |
Description: | Wireless security settings are incorrect. Please change the settings |
Causes: | Wireless security settings like a WEP/WPA/WPA2 are incorrect. |
Remedy: | 1) Turn the machine and AP off then on. 2) Change the wireless network settings. |
Error code: | S6-3233 |
Description: | Not connected from the wireless AP. If you do not reconnect automatically, check the wireless settings |
Causes: | Wireless BSSID value is 0 or wireless module is disconnected. |
Remedy: | 1) Turn the machine and AP off then on. 2) Change the wireless network settings. |
Error code: | S6-3234 |
Description: | Failed connection to WPS. Try again or set up other wireless connection |
Causes: | WPS connection to AP is failed. |
Remedy: | 1) Retry the connection with WPS button. |
Error code: | S6-3235 |
Description: | Error: #S6-3235 / Wi-Fi Direct is not ready. Turn off then on. Call for service if the problem persists |
Causes: | Wi-Fi Direct is not ready because of library initialization. |
Remedy: | 1) Turn the machine off then on. 2) If the problem persist, initialize the wireless setting and try again. |
Error code: | S6-3236 |
Description: | Error: #S6-3236 / Failed to connect to Wi-Fi Direct. Turn off your mobile device and turn it on |
Causes: | Failed to connect to Wi-Fi Direct. |
Remedy: | 1) Turn off Wi-Fi Direct function then on. 2) Turn off your mobile device and turn it on. 3) Turn off the printer and turn it on. |
Error code: | S7-2110 |
Display: | Fuser Failure: #S7-2110. Turn off then on |
Description: | Fuser Failure: #S7-2110. Turn off then on |
Causes: | Heater control relay is abnormal. |
Remedy: | 1) Turn the machine off. Re-install the fuser unit, then turn the machine on. 2) If the problem persists, replace the Fuser unit(110V : JC91-01158A, 220V : JC91-01157A). |
Error code: | U1-2112, U1-2120, U1-2132 |
Description: | Fuser unit Failure: #Ul-2xxx. Tum off then on. Call for service if the problem perists |
Causes: | T11e temperature control of fuser unit is abnormal. (Open Heat EITor or Low Heat EITor or Over Heat EITor) I T11ennistor is defective. I Fuser unit connection is bad. |
Remedy: | 1) After checking the fuser installation, turn the machine off then on. 2) Open the rear cover. Lift up the right side and release the rear cover. 3) If there is no problem, remove 4 screws. 4) Lift up the both levers. Then take off the fuser unit. 5) Remove the Frame-cover-upper after removing 2 screws. And measure the thermostat continuity. Check if the thermostat is opened. 6) Measure the LAMP-HALOGEN resistance value from the center and both sides. Check if it has the continuity. 7) Check if the Draw-connector harness is correct. Check its color. 8) Check if 2 thermistor connectors are connected properly. 9) Measure the Thermistor resistance value from the center and both sides. Check if it has the continuity. (3 Red Circles) 10)Check if the thermistor connector on the main board is connected properly. 11) Check if the FDB connector is connected properly. 12)Check if the voltage in user environment is in this range (80V ~ 140V, 160V ~ 260V). 13)If there is no problems for above steps, update the firmware. 14)Replace the FDB(JC44-00204A(220V)/JC44-00203A(110V)). If the problem persists, replace the SMPS(JC44-00092C(220V)/JC44-00091C(110V)) If the problem persists, replace the main board. |
Error code: | U1-2115, U1-2116 |
Display: | Fuser Unit Failure #U1-2115 : Turn off then on. Fuser Unit Failure #U1-2116 : Turn off then on. |
Description: | Error #U1-2115 Turn off then on Error #U1-2116 Turn off then on |
Causes: | The fuser unit has the problem for pressure control. |
Remedy: | 1) Turn the machine off. Remove and reinstall the fuser unit. Turn the machine off. Is this error message disappeared? 2) Open the rear cover. Check if the fuser pressure cam is working normally. • If the cam operation is normal, replace the cam sensor. 3) Remove the side cover. Check if the fuser motor is working normally. 4) Check if the swing-gear is in the position below when the cam works. If not, replace the fuser drive unit. |
Error code: | U1-2117 |
Display: | Fuser Unit Failure: #U1-2117. Turn off then on |
Description: | Fuser unit Failure: #U1-2117. Turn off then on. |
Causes: | The machine can’t detect that the fuser unit is installed. |
Remedy: | 1) After checking the fuser installation, turn the machine off then on. 2) Open the rear cover. Lift up the right side and release the rear cover. 3) If there is no problem, remove 4 screws. 4) Lift up the both levers. Then take off the fuser unit. 5) If there is no problem for above steps, assemble and reinstall fuser unit. Then turn the machine on. 6) If the same error persists, execute the memory clear. 7) If the same error persists, replace the fuser unit with new one. 8) If the same error persists, replace the main board. |
Error code: | U1-2135, U1-23xx |
Description: | Fuser unit Failure: #Ul-2xxx. Tum off then on. Call for service if the problem perists |
Causes: | T11e temperature control of fuser unit is abnormal. (Open Heat EITor or Low Heat EITor or Over Heat EITor) I T11ennistor is defective. I Fuser unit connection is bad. |
Remedy: | 1) After checking the fuser installation, turn the machine off then on. 2) Open the rear cover. Lift up the right side and release the rear cover. 3) If there is no problem, remove 4 screws. 4) Lift up the both levers. Then take off the fuser unit. 5) Remove the Frame-cover-upper after removing 2 screws. And measure the thermostat continuity. Check if the thermostat is opened. 6) Measure the LAMP-HALOGEN resistance value from the center and both sides. Check if it has the continuity. 7) Check if the Draw-connector harness is correct. Check its color. 8) Check if 2 thermistor connectors are connected properly. 9) Measure the Thermistor resistance value from the center and both sides. Check if it has the continuity. (3 Red Circles) 10)Check if the thermistor connector on the main board is connected properly. 11) Check if the FDB connector is connected properly. 12)Check if the voltage in user environment is in this range (80V ~ 140V, 160V ~ 260V). 13)If there is no problems for above steps, update the firmware. 14)Replace the FDB(JC44-00204A(220V)/JC44-00203A(110V)). If the problem persists, replace the SMPS(JC44-00092C(220V)/JC44-00091C(110V)) If the problem persists, replace the main board. |
Error code: | U2-1111, U2-1112 |
Display: | U2-1111, U2-1112, U2-1113, U2-1114 LSU failure errors |
Description: | LSU Failure: #U2-1111. Turn off then on. LSU Failure: #U2-1112. Turn off then on. |
Causes: | LSU motor does not operate of it operates abnormally. Motor ready signal is abnormal. |
Remedy: | 1) Turn the machine off then on. Check for the LSU motor operation sound during warm-up. 2) Print a Demo page and check the printout is normal. 3) If the problem persists, check the following: • If the LSU motor makes a sound, a) By SVC mode, Check if the motor ready signal is occurred. (Diagnostics > Engine Diagnostics > Engine Test Routines > 110–0000) b) If not, open the side-cover and replace the LSU(JC97–04017B) • If the LSU motor does not make a sound, a) Unplug and reconnect the LSU flat cable connecting the LSU. Then check the operation sound of LSU. b) Unplug and reconnect the LSU flat cable on main board. Then check the operation sound of LSU. c) If the LSU flat cable is defective, replace FFC. d) If the LSU cable is OK, replace the LSU(JC97–04017B) |
Error code: | U2-1113, U2-1114 |
Display: | U2-1111, U2-1112, U2-1113, U2-1114 LSU failure errors |
Description: | LSU Failure: #U2-1113. Turn off then on. LSU Failure: #U2-1114. Turn off then on. |
Causes: | LSU motor does not operate of it operates abnormally. Motor ready signal is abnormal. |
Remedy: | 1) Turn the machine off then on. Check for the LSU motor operation sound during warm-up. 2) Print a Demo page and check the printout is normal. 3) If the problem persists, check the following: • If the LSU motor makes a sound, a) By SVC mode, Check if the motor ready signal is occurred. (Diagnostics > Engine Diagnostics > Engine Test Routines > 110–0000) b) If not, open the side-cover and replace the LSU(JC97–04017B) • If the LSU motor does not make a sound, a) Unplug and reconnect the LSU flat cable connecting the LSU. Then check the operation sound of LSU. b) Unplug and reconnect the LSU flat cable on main board. Then check the operation sound of LSU. c) If the LSU flat cable is defective, replace FFC. d) If the LSU cable is OK, replace the LSU(JC97–04017B) |