Samsung SCX-1150F

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

термическая струйная

Макс. формат

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Технология печати	термическая струйная
Тип	струйный
Тип устройства	МФУ
Телефон
Макс. формат	A4
Цветность печати	цветная
Размещение	настольный
Сканер
Печать фотографий
Копир
Факс
Принтер
Печать без полей
Пигментные чернила
Двусторонняя печать
Прямая печать
Макс, разрешение для ч/б печати
По X	2 400
По Y	1 200
Скорость ч/б печати
A4	10
A4	7
Копир
Макс, количество копий за цикл	99
Значение масштаба
Минимальное	0,25
Максимальное	4
Макс, разрешение (ч/б)
По Y	300
По X	300
По Y	600
По X	600
По Y	1 200
Скорость ч/б копирования
A4	5
Сканер
Устройство автоподачи оригиналов	одностороннее
Макс. формат оригинала	A4
Емкость устройства автоподачи оригиналов	30
Оттенки серого	256
Тип сканера	протяжный
Тип датчика сканера	ПЗС (CCD)
Разрешение сканера
По Х	600
Печать на:
CD/DVD
Фотобумаге
Рулоне
Карточках
Конвертах
Пленках
Этикетках
Глянцевой бумаге
Матовой бумаге
Факс
Цветной
PC Fax
Память	320
Макс, скорость передачи данных	33,6 Кбит/с
Телефон
Автоответчик
Спикерфон
Проводная трубка
Беспроводная трубка
Стандарт DECT
АОН
Caller ID
Языки управления
PostScript 3
PCL 5c
PCL 5e
PCL 6
PPDS
PDF
PostScript
PostScript 2
Подача бумаги
Стандартная	100
Финишер
Брошюровщик
Степлер
Электронная сортировка
Сортер
Сортировка со сдвигом
Интерфейсы
Версия USB	2,0
RS-232
Устройство для чтения карт памяти
Инфракрасный порт
Bluetooth
Веб-интерфейс
FireWire (IEEE 1394)
Wi-Fi
Ethernet (RJ-45)
USB
LPT
Дополнительная информация
Экран
Поддержка ОС
Linux
Mac OS
DOS
Windows
Потребляемая мощность
В режиме ожидания	15
Габариты
Высота	315
Глубина	440
Ширина	477
Вес	10

Модули

Scanner assembly

ADF unit

Main Cover Assembly

Feeder Unit

Main assembly

Engine Assy

OPE Unit

Детали

Деталь:	MEA-COVER PLATEN ASSY
Парткод:	JB81-00226A

Деталь:	ELA HOU-ADF MOTOR ASSY
Парткод:	JB96-01340A

Деталь:	MEA UNIT-PICK UP ASSY
Парткод:	JC97-01582A

Деталь:	SCREW TAPPING
Парткод:	6002-000175

Деталь:	Screw-Taptite
Парткод:	6003-000196

Деталь:	Screw-Taptite
Парткод:	6003-000269

Деталь:	NPR-SPRING PINCH DRIVE
Парткод:	JB71-00038A

Деталь:	IPR SHAFT EXIT
Парткод:	JC70-00242A

Деталь:	PMO-COVER PLATEN(4IN1)
Парткод:	JB72-01165A

Деталь:	ICT-SHAFT PINCH
Парткод:	JC70-00265A

Деталь:	RPR-ROLLER EXIT IDLE
Парткод:	JC73-00091A

Деталь:	PMO-ROLL PINCH
Парткод:	JG72-40663A

Деталь:	MPR-WHITE SPONGE SHEET
Парткод:	JB74-00049A

Деталь:	PMO-COVER ADF UPPER
Парткод:	JC72-00736A

Деталь:	RMO-ADF RUBBER
Парткод:	JC73-00052A

Деталь:	PMO-HOLDER ADF
Парткод:	JB72-00825A

Деталь:	RPR-SPONGE ADF
Парткод:	JB73-10913A

Деталь:	SPRING ETC-COILADF
Парткод:	JC61-00040A

Деталь:	CBF HARNESS ADF ROLLER GND
Парткод:	JC39-00187A

Деталь:	CBF HARNESS-DRIVER GND
Парткод:	JB39-00065A

Деталь:	PMO-ACTUATOR SENSOR SCAN
Парткод:	JC72-00746A

Деталь:	SPRING ETC-TORSION DOC (CC2-F)
Парткод:	JB61-00076A

Деталь:	PMO-ACTUATOR SENSOR REGI
Парткод:	JC72-00747A

Деталь:	PBASUB-ADF DETSEN
Парткод:	JC92-01366A

Деталь:	PBASUB-ADF POS SEN
Парткод:	JC92-01365A

Деталь:	PMO-ACTUATOR SENSOR DOC
Парткод:	JB72-00837A

Деталь:	MOTORADF
Парткод:	JC31-00017A

Деталь:	IPR-BRKT ADF MOTOR
Парткод:	JC70-00224A

Деталь:	GEAR-CLUTCH 29
Парткод:	JB66-00101A

Деталь:	PMO-WHITE CLUTCH SUB 29
Парткод:	JB72-00844A

Деталь:	GEAR-CLUTCH 39
Парткод:	JC66-00322A

Деталь:	GEAR-IDLE20/33
Парткод:	JG66-40038A

Деталь:	GEAR-REDUCTION 45/19
Парткод:	JC66-00324A

Деталь:	GEAR-JAM REMOVE
Парткод:	JC66-00329A

Деталь:	GEAR-IDLE25
Парткод:	JG66-40036A

Деталь:	PMO-COVER OPEN
Парткод:	JB72-01167A

Деталь:	PMO-GUIDE PAPER
Парткод:	JB72-00843A

Деталь:	CBF D SUB_CABLE-ADF-MAIN(CABLE)
Парткод:	JB39-00146A

Деталь:	IPR-SPRING PINCH
Парткод:	JC70-00260A

Деталь:	MAIN-ADF
Парткод:	JB92-01200A

Деталь:	PMO-COVER ADF LOWER
Парткод:	JC72-00735A

Деталь:	NPR-SPRING GND
Парткод:	JC71-00031A

Деталь:	MEC- BRUSH ANTISTATIC
Парткод:	JC75-00095A

Деталь:	SPRING ETC-WHITE BAR
Парткод:	JC61-00548A

Деталь:	IPR-BRKT WHITE BAR
Парткод:	JC70-00225A

Деталь:	PPR-WHITE BAR SHEET
Парткод:	JC72-00752A

Деталь:	GEAR-EXIT 23
Парткод:	JC66-00323A

Деталь:	SPRING-CLUTCH
Парткод:	JC61-00062A

Деталь:	PMO-BUSHING HOLDER
Парткод:	JG72-40732A

Деталь:	RMO-ROLLER EXIT
Парткод:	JC73-00088A

Деталь:	Ring-C
Парткод:	6044-000159

$xerox\JB66-00103A.jpg$

Деталь:	GEAR-ADF 38
Парткод:	JB66-00103A
Цена:	260 ₽

Деталь:	PMO-BUSH
Парткод:	JB72-00819A

Деталь:	RMO-ROLLER DRIVE
Парткод:	JC73-00087A

Деталь:	GEAR-IDLE17/35
Парткод:	JG66-40039A

Деталь:	PMO-TX STACKER
Парткод:	JB72-01166A

Деталь:	PMO-DOC GUIDE(L)
Парткод:	JB72-01171A

Деталь:	PMO-DOC GUIDE(R)
Парткод:	JB72-01170A

Деталь:	GEAR PINION
Парткод:	JG66-40003A
Цена:	260 ₽

Деталь:	PMO-HINGE FRAME
Парткод:	JB72-01175A

Деталь:	PMO-HINGE BRAKE
Парткод:	JB72-01177A

Деталь:	PMO-HINGE SCREW
Парткод:	JB72-01176A

Деталь:	SUPT BRACKET-HINGE
Парткод:	JB61-00110A

Деталь:	PMO-HINGE PRESSURE
Парткод:	JB72-01178A

Деталь:	PMO-HINGE BODY
Парткод:	JB72-01174A

Деталь:	ICT-HINGE SHAFT (4 in 1)
Парткод:	JB70-00236A

Деталь:	MEA-COVER MAIN
Парткод:	JB97-01539A

Деталь:	PMO-DOOR FRONT
Парткод:	JB72-01144A

Деталь:	FOOT-RUBBER
Парткод:	JB61-40901A

Деталь:	MPR-FELT UPPER
Парткод:	JB74-00014A

Деталь:	MPR-FELT LOWER
Парткод:	JB74-00015A

Деталь:	CBF HARNESS-MAIN_COVER OPEN
Парткод:	JB39-00116A

Деталь:	PMO-BASE STACKER
Парткод:	JB72-01143A

Деталь:	PMO-EXIT TRAY MIDDLE
Парткод:	JB72-00978C

Деталь:	PMO-EXIT TRAY EXTENSION
Парткод:	JB72-00982C

Деталь:	MEA UNIT-FEEDER
Парткод:	JB97-01535A

Деталь:	MEA UNIT-PICKUP ROLL
Парткод:	JB97-00965A

Деталь:	RMO-BUCKLER FRICTION
Парткод:	JB73-00019A

Деталь:	ELA UNIT-ENGINE ASSY
Парткод:	JB96-01330A

Деталь:	MEC-HOLDER ROLLER
Парткод:	JB75-11111A

Деталь:	MEAUNIT-BRKT LF
Парткод:	JB97-01536A

Деталь:	MEC-PULLEY IDLE
Парткод:	JB75-11110A

Деталь:	ICT-SHAFT CR
Парткод:	JB70-40906A

Деталь:	SPRING-SHAFT CR
Парткод:	JB61-70913A

Деталь:	MEAUNIT-C/R/SEC
Парткод:	JB96-01303A

Деталь:	BEARING-FEED R
Парткод:	JB66-10002A

Деталь:	MEC-ROLLER FEED
Парткод:	JB75-11112A

Деталь:	PRP-ENCODER STRIP(V)
Парткод:	JB72-00662A

Деталь:	MEC-FRAME BASE
Парткод:	JB75-00170A

Деталь:	ELAUNIT-C/R MOTOR
Парткод:	JB96-01312A

Деталь:	SPRING-PS ENCODER
Парткод:	JB61-70917A

Деталь:	MEC-FRAME MAIN
Парткод:	JB75-00349A

Деталь:	MEC-FRAME HOME
Парткод:	JB75-00174A

Деталь:	SPRING-ES ACTUATOR
Парткод:	JB61-70919A

Деталь:	PMO-ACTUATOR FEED
Парткод:	JB72-40993A

Деталь:	MOTOR-STEP LF(V)
Парткод:	JB31-00007A

Деталь:	PMO-STOPPER PULLEY
Парткод:	JB72-41212A

Деталь:	MEC-SUB FRAME BASE
Парткод:	JB75-11126A

Деталь:	MOTOR-DC CARRIAGE
Парткод:	JB31-00005A

Деталь:	CBF-HARNESS-DC MOTOR
Парткод:	JB39-00094A

Коды ошибок

Описание

Парткод

Ink-C60

Ink-M50

Название

Samsung Цветной струйный картридж

Samsung Черный струйный картридж

Деталь:	Belt-Timing Gear
Парткод:	6602-001067
Цена:	420 ₽

Деталь:	ELA ETC-BRKT SCAN MOTOR
Парткод:	JB96-01344A

Деталь:	ELA MODUL-SCANNER (UMAX)
Парткод:	JB96-01317A

Деталь:	MOTOR-SCAN
Парткод:	JB31-00011A
Цена:	1 300 ₽

Деталь:	ELA UNIT-ENGINE ASSY(4 IN 1)
Парткод:	JB96-01330A

Деталь:	MEA-COVER REAR(4 IN 1)
Парткод:	JB97-01537B

Деталь:	CBF HARNESS-POWER GND
Парткод:	JB39-00131A

Деталь:	CBF HARNESS-MAIN POWER
Парткод:	JB39-00129A

Error code:	01
Display:	ERROR CONDITION INVALID HEAD
Description:	The ERROR light flashes.
Causes:	The printhead was replaced with one that is not a genuine Zebra™ printhead.
Remedy:	Install a genuine Zebra printhead.

Error code:	02
Display:	ERROR CONDITION RIBBON OUT
Description:	The printer stops; the ERROR light flashes.
Causes:	In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly.
Remedy:	Load ribbon correctly. 1. Load ribbon correctly. See Load Ribbon on page 64. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Load media correctly. See Load Media on page 58. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Print a sensor profile. See Print Sensor Profile on page 89. The ribbon out threshold (marked by the word RIBBON) is likely too high, above the black area that indicates where the ribbon is detected. 2. Calibrate the sensors or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73.

Деталь:	MCT-SCAN GLASS
Парткод:	JB74-00050A

Деталь:	IPR-HOLDER GLASS
Парткод:	JB70-00148A

Деталь:	PMO-PULLEY
Парткод:	JB72-00763A

Деталь:	CABLE TIE
Парткод:	6501-000115

Error code:	03
Display:	WARNING RIBBON IN
Description:	The ERROR light flashes.
Causes:	Ribbon is loaded, but the printer is set for direct thermal mode.
Remedy:	Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81.

Error code:	04
Display:	ERROR CONDITION PAPER OUT
Description:	The printer stops; the ERROR light flashes.
Causes:	The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded.
Remedy:	Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration.

Error code:	05
Display:	ERROR CONDITION HEAD OPEN
Description:	The printer stops; the ERROR light flashes.
Causes:	The printhead is not fully closed. The head open sensor is not working properly.
Remedy:	Replace the sensor.

Error code:	06
Display:	THERMISTOR FAULT
Description:	The ERROR light flashes.
Causes:	The printhead has a faulty thermistor.
Remedy:	Replace the printhead.

Error code:	07
Display:	WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD
Description:	The printer stops; the ERROR light is on; the printer cycles through these three messages.
Causes:	The printhead data cable is not properly connected. The printhead has a faulty thermistor.
Remedy:	Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead.

Error code:	08
Display:	WARNING HEAD COLD
Description:	The printer prints while the ERROR light flashes.
Causes:	The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor.
Remedy:	Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead.

Error code:	09
Display:	WARNING HEAD TOO HOT
Description:	The printer stops; the ERROR light flashes.
Causes:	The printhead is over temperature.
Remedy:	Allow the printer to cool. Printing automatically resumes when the printhead elements cool to an acceptable operating temperature.

Error code:	10
Display:	DEFRAGMENTING
Description:	The printer stops.
Causes:	The printer is defragmenting memory.
Remedy:	Caution • Do NOT turn off the printer power during defragmenting. Doing so can damage the printer. Allow the printer to finish defragmenting. If you get this error message frequently, check your label formats. Formats that write to and erase memory frequently may cause the printer to defragment often. Using properly coded label formats usually minimizes the need for defragmenting. If this error message does not go away, contact Technical Support. The printer requires service.

Error code:	11
Display:	ERROR CONDITION CUTTER JAM
Description:	The printer stops; the ERROR light flashes.
Causes:	Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers. The cutter blade is in the media path.
Remedy:	Turn off the printer power and unplug the printer. Inspect the cutter module for debris and clean as needed following the cleaning instructions in Clean the Cutter Module on page 135.

Error code:	12
Description:	General print quality issues
Causes:	The printer is set at the incorrect print speed. You are using an incorrect combination of labels and ribbon for your application. The printer is set at an incorrect darkness level. The printhead is dirty. Incorrect or uneven printhead pressure. The printhead is improperly balanced.
Remedy:	For optimal print quality, set the print speed to the lowest possible setting for your application via control panel, the driver, or the software. See Adjust Print Speed on page 79. You may want to perform the FEED Self Test on page 120. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. For optimal print quality, set the darkness to the lowest possible setting for your application via the control panel, the driver, or the software. See Adjust Print Darkness on page 78. You may want to perform the FEED Self Test on page 120 to determine the ideal darkness setting. Clean the printhead. See Clean the Printhead and Platen Roller on page 131. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Adjust the printhead balance.

Samsung SCX-1150F

Общие характеристики

Технология печати

Тип

Тип устройства

Телефон

Макс. формат

Цветность печати

Размещение

Сканер

Печать фотографий

Копир

Факс

Принтер

Печать без полей

Пигментные чернила

Двусторонняя печать

Прямая печать

Макс, разрешение для ч/б печати

Скорость ч/б печати

Копир

Макс, количество копий за цикл

Значение масштаба

Макс, разрешение (ч/б)

Скорость ч/б копирования

Сканер

Устройство автоподачи оригиналов

Макс. формат оригинала

Емкость устройства автоподачи оригиналов

Оттенки серого

Тип сканера

Тип датчика сканера

Разрешение сканера

Печать на:

Факс

Цветной

PC Fax

Память

Макс, скорость передачи данных

Телефон

Автоответчик

Спикерфон

Проводная трубка

Беспроводная трубка

Стандарт DECT

АОН

Caller ID

Языки управления

Подача бумаги

Финишер

Брошюровщик

Степлер

Электронная сортировка

Сортер

Сортировка со сдвигом

Интерфейсы

Версия USB

RS-232

Устройство для чтения карт памяти

Инфракрасный порт

Bluetooth

Веб-интерфейс

FireWire (IEEE 1394)

Wi-Fi

Ethernet (RJ-45)

USB

LPT

Дополнительная информация

Экран

Поддержка ОС

Потребляемая мощность

Габариты

Высота

Глубина

Ширина

Вес

Модули

Детали

Коды ошибок

Описание

Error code:	13
Description:	Long tracks of missing print on several labels
Causes:	Print element damaged.
Remedy:	Replace the printhead.

Error code:	14
Description:	Wrinkled ribbon
Causes:	Ribbon fed through the machine incorrectly. Incorrect burn temperature. Incorrect or uneven printhead pressure. Media not feeding properly; walking from side to side. The strip plate needs adjusting. The printhead needs vertical adjustment. The printhead is improperly balanced. The printhead and platen roller need to be realigned.
Remedy:	See Load Ribbon on page 64. Set the darkness to the lowest possible setting for good print quality. See Adjust Print Darkness on page 78. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Make sure that media is snug by adjusting the media guide, or call a service technician. Adjust the printhead balance.

Error code:	15
Description:	Printing too light or too dark over the entire label
Causes:	The media or ribbon is not designed for high-speed operation. You are using an incorrect combination of media and ribbon for your application. You are using ribbon with direct thermal media. Incorrect or uneven printhead pressure.
Remedy:	Replace supplies with those recommended for high-speed operation. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. Direct thermal media does not require ribbon. To check if you are using direct thermal media, perform the label scratch test in When to Use Ribbon on page 62. Set the pressure to the minimum needed. See Adjust Printhead Pressure on page 70.

Error code:	16
Description:	Smudge marks on labels
Causes:	The media or ribbon is not designed for high-speed operation.
Remedy:	Replace supplies with those recommended for high-speed operation.

Error code:	17
Description:	Misregistration/skips labels
Causes:	The printer is not calibrated. Improper label format.
Remedy:	Recalibrate the printer. Use correct label format.

Error code:	18
Description:	Misregistration and misprint of one to three labels
Causes:	The platen roller is dirty. Media does not meet specifications.
Remedy:	See Clean the Printhead and Platen Roller on page 131. Use media that meets specifications.

Error code:	19
Description:	Vertical drift in top-of-form position
Causes:	The printer is out of calibration. Vertical drift occurs during normal printer operation. Note • A vertical drift of ± 4 to 6 dot rows (approximately 0.5 mm) is within normal tolerances. The platen roller is dirty.
Remedy:	Recalibrate the printer. Calibrate the printer. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131.

Error code:	20
Description:	Vertical image or label drift
Causes:	The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media.
Remedy:	Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation.

Error code:	21
Description:	The bar code printed on a label does not scan.
Causes:	The bar code is not within specifications because the print is too light or too dark. Not enough blank space around the bar code.
Remedy:	Perform the FEED Self Test on page 120. Adjust the darkness or print speed settings as necessary. Leave at least 1/8 in. (3.2 mm) between the bar code and other printed areas on the label and between the bar code and the edge of the label.

Error code:	22
Description:	Loss of printing registration on labels. Excessive vertical drift in top-of-form registration.
Causes:	The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly.
Remedy:	Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58.