Canon imageCLASS MF521dw
Рейтинг
Модули
100B External Covers, Panels, Etc. (MF525dw)
104B Internal Components 4 (120V)
104E Internal Components 4 (230V)
103 INTERNAL COMPONENTS 3
400D Reader Assembly (230V
130A Control Panel Assembly (MF521dw, MF525x, MF525dw)
102C Internal Components 2 (230V)
930A Main Controller PCB Assembly Set (MF521, MF525 Series)
102B Internal Components 2 (120V)
100E External Covers, Panels, Etc. (MF525x)
101 INTERNAL COMPONENTS 1
160 READER/ADF ASSEMBLY
400B Reader Assembly (120V LTN)
161 Paper Feeder Assembly
Детали 400B Reader Assembly (120V LTN)
| Деталь: | TRAY, PAPER DELIVERY |
| Парткод: | FE8-0822-000 |
| Деталь: | BUSHING, M.P. COVER |
| Парткод: | FE8-0827-000 |
| Деталь: | RIGHT COVER ASSY |
| Парткод: | FM1-T493-000 |
| Деталь: | COVER, FRONT, RIGHT |
| Парткод: | FE8-6700-000 |
| Деталь: | CARTRIDGE DOOR ASSY |
| Парткод: | FM1-T490-000 |
| Деталь: | SHAFT, SUPPORT |
| Парткод: | RC4-3002-000 |
| Деталь: | LINK, PRESSURE RELEASE |
| Парткод: | RC4-4479-000 |
| Деталь: | TOP COVER ASSY |
| Парткод: | FM1-T494-000 |
| Деталь: | REAR DOOR ASSY |
| Парткод: | FM1-T491-000 |
| Деталь: | LEFT COVER ASSY |
| Парткод: | FM1-T492-000 |
| Деталь: | SPEAKER |
| Парткод: | FK3-3944-000 |
| Деталь: | LABEL, CASSETTE OPERATOR |
| Парткод: | FU2-1858-000 |
| Деталь: | LABEL, HIGH TMP. CAUTION |
| Парткод: | FU2-1860-000 |
| Деталь: | COVER, IOT |
| Парткод: | FE8-0835-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, TOP, REAR |
| Парткод: | FE8-6707-000 |
| Деталь: | COVER, USB |
| Парткод: | FE8-6704-000 |
| Деталь: | SHEET, HANDSET |
| Парткод: | FL1-0525-000 |
| Цена: | 800 ₽ |
| Деталь: | BUTTON, DOOR, FRONT |
| Парткод: | FE8-0831-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | MODULE, WLAN |
| Парткод: | FK4-4651-000 |
| Деталь: | FIXING POWER SUPPLY PCB ASSY |
| Парткод: | FM2-A823-000 |
| Деталь: | L.V. POWER SUPPLY PCB ASSY |
| Парткод: | FM2-A825-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | FK4-5013-000 |
| Деталь: | FAN |
| Парткод: | RK2-1378-000 |
| Деталь: | PAPER FEED DRIVE ASSY |
| Парткод: | RM2-5715-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | NCU PCB ASSEMBLY |
| Парткод: | FM2-D816-000 |
| Деталь: | OFFHOOK PCB ASSEMBLY |
| Парткод: | FM1-R867-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | FK2-8767-000 |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | MODULE, WLAN |
| Парткод: | FK4-4651-000 |
| Деталь: | FIXING POWER SUPPLY PCB ASSY |
| Парткод: | FM2-A824-000 |
| Деталь: | L.V. POWER SUPPLY PCB ASSY |
| Парткод: | FM2-A826-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | FK4-5013-000 |
| Деталь: | FAN |
| Парткод: | RK2-1378-000 |
| Деталь: | PAPER FEED DRIVE ASSY |
| Парткод: | RM2-5715-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | NCU PCB ASSEMBLY |
| Парткод: | FM2-D816-000 |
| Деталь: | OFFHOOK PCB ASSEMBLY |
| Парткод: | FM1-R867-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | FK2-8767-000 |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | ROLLER, TRANSFER |
| Парткод: | RM1-4023-000 |
| Деталь: | HOLDER, TRANSFER ROLLER, RIGHT |
| Парткод: | RC4-3133-000 |
| Деталь: | HOLDER, TRANSFER ROLLER, LEFT |
| Парткод: | RC4-3134-000 |
| Деталь: | PAPER PICK-UP ROLLER ASSY |
| Парткод: | RM2-5741 -000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU8-2935-000 |
| Деталь: | ROLLER, MULTI-PURPOSE |
| Парткод: | RL2-0656-000 |
| Деталь: | PAD, MULTI-PURPOSE SEPARATION |
| Парткод: | RL2-0657-000 |
| Деталь: | REGISTRATION ASSY |
| Парткод: | FM1-N761-000 |
| Деталь: | MULTI-PURPOSE GEAR ASSY |
| Парткод: | RM2-5700-000 |
| Деталь: | SOLENOID ASSY |
| Парткод: | RM1-5421 -000 |
| Деталь: | HINGE, CARTRIDGE DOOR, LEFT |
| Парткод: | RC4-3010-000 |
| Деталь: | DC CONTROLLER PCB ASSEMBLY |
| Парткод: | FM2-C918-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | FK4-4208-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1670-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | SPACER, CIS |
| Парткод: | FE8-3479-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FE8-6736-000 |
| Деталь: | CONTACT IMAGE SENSOR,FA106H-01 |
| Парткод: | FK4-4050-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-5054-000 |
| Деталь: | PULLEY UNIT |
| Парткод: | FL1-1412-000 |
| Деталь: | DC MOTOR ASSEMBLY |
| Парткод: | FM1-T334-000 |
| Деталь: | CABLE, READER SIGNAL, 3 |
| Парткод: | FM2-C968-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | COPYBOARD GLASS UNIT |
| Парткод: | FM1-T335-000 |
| Деталь: | LABEL, WIDTH SIZE |
| Парткод: | FE8-6737-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FE8-9143-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FE8-4196-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | FM1-U532-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-T083-000 |
| Деталь: | COVER, PANEL, REAR |
| Парткод: | FE8-8103-000 |
| Деталь: | COVER, PANEL, REAR UPPER |
| Парткод: | FE8-6209-000 |
| Деталь: | COVER, PANEL, REAR LOWER |
| Парткод: | FE8-6210-000 |
| Деталь: | COVER, PANEL, LOWER |
| Парткод: | FE8-6211-000 |
| Деталь: | COVER, PANEL MOUNT, LEFT |
| Парткод: | FE8-6708-000 |
| Деталь: | COVER, PANEL MOUNT, RIGHT |
| Парткод: | FE8-6709-000 |
| Деталь: | COVER, PANEL MOUNT, UPPER |
| Парткод: | FE8-6710-000 |
| Деталь: | HINGE ASSEMBLY |
| Парткод: | FM1-T109-000 |
| Деталь: | CABLE, HDMI |
| Парткод: | FK4-5012-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | NPN |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM1-V152-000 |
| Деталь: | CASSETTE ASSY |
| Парткод: | FM1-N488-000 |
| Деталь: | LABEL, CST. PAPER SIZE |
| Парткод: | FU2-1855-000 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | RM2-5745-000 |
| Деталь: | BACK END LIMIT ASSEMBLY |
| Парткод: | RM2-5746-000 |
| Деталь: | LEVER, SWITCH |
| Парткод: | FE8-0847-000 |
| Деталь: | USB RELAY PCB ASSEMBLY |
| Парткод: | FM1-R870-000 |
| Цена: | 3 400 ₽ |
| Деталь: | SWITCH PCB ASSY |
| Парткод: | FM1-V946-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE8-7096-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1670-000 |
| Деталь: | COVER, FULL DETECT SENSOR |
| Парткод: | RC4-3219-000 |
| Деталь: | FILM BIAS ASSY |
| Парткод: | RM2-5689-000 |
| Деталь: | PAPER RE-PICK UP CLUTCH ASSY |
| Парткод: | RM2-8514-000 |
| Деталь: | MAIN MOTOR ASSY |
| Парткод: | RM2-8684-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | MAIN CONTROLLER PCB ASSY SET |
| Парткод: | FM1-U534-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM1-V151-000 |
| Деталь: | CASSETTE ASSY |
| Парткод: | FM1-N488-000 |
| Деталь: | LABEL, CST. PAPER SIZE |
| Парткод: | FU2-1855-000 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | RM2-5745-000 |
| Деталь: | BACK END LIMIT ASSEMBLY |
| Парткод: | RM2-5746-000 |
| Деталь: | LEVER, SWITCH |
| Парткод: | FE8-0847-000 |
| Деталь: | USB RELAY PCB ASSEMBLY |
| Парткод: | FM1-R870-000 |
| Цена: | 3 400 ₽ |
| Деталь: | SWITCH PCB ASSY |
| Парткод: | FM1-V946-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE8-7096-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1670-000 |
| Деталь: | COVER, FULL DETECT SENSOR |
| Парткод: | RC4-3219-000 |
| Деталь: | FILM BIAS ASSY |
| Парткод: | RM2-5689-000 |
| Деталь: | PAPER RE-PICK UP CLUTCH ASSY |
| Парткод: | RM2-8514-000 |
| Деталь: | MAIN MOTOR ASSY |
| Парткод: | RM2-8684-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | TRAY, PAPER DELIVERY |
| Парткод: | FE8-0822-000 |
| Деталь: | BUSHING, M.P. COVER |
| Парткод: | FE8-0827-000 |
| Деталь: | RIGHT COVER ASSY |
| Парткод: | FM1-T493-000 |
| Деталь: | COVER, FRONT, RIGHT |
| Парткод: | FE8-6700-000 |
| Деталь: | CARTRIDGE DOOR ASSY |
| Парткод: | FM1-T490-000 |
| Деталь: | SHAFT, SUPPORT |
| Парткод: | RC4-3002-000 |
| Деталь: | LINK, PRESSURE RELEASE |
| Парткод: | RC4-4479-000 |
| Деталь: | TOP COVER ASSY |
| Парткод: | FM1-T494-000 |
| Деталь: | REAR DOOR ASSY |
| Парткод: | FM1-T491-000 |
| Деталь: | LEFT COVER ASSY |
| Парткод: | FM1-T492-000 |
| Деталь: | SPEAKER |
| Парткод: | FK3-3944-000 |
| Деталь: | LABEL, CASSETTE OPERATOR |
| Парткод: | FU2-1858-000 |
| Деталь: | LABEL, HIGH TMP. CAUTION |
| Парткод: | FU2-1860-000 |
| Деталь: | COVER, IOT |
| Парткод: | FE8-0835-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, TOP, REAR |
| Парткод: | FE8-6707-000 |
| Деталь: | COVER, USB |
| Парткод: | FE8-6704-000 |
| Деталь: | SHEET, HANDSET |
| Парткод: | FL1-0525-000 |
| Цена: | 800 ₽ |
| Деталь: | BUTTON, DOOR, FRONT |
| Парткод: | FE8-0831-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | MICROSWITCH |
| Парткод: | RK2-0534-000 |
| Деталь: | FAN |
| Парткод: | RK2-1378-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | RK2-6259-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | RK2-6260-000 |
| Деталь: | H.V. POWER SUPPLY PCB ASSY |
| Парткод: | RM2-7945-000 |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | RM2-5528-000 |
| Деталь: | TAG CABLE ASSY |
| Парткод: | RM2-5702-000 |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1670-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FL1-4062-000 |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FE8-4191-000 |
| Деталь: | PANEL, COPYBOARD |
| Парткод: | FE8-6741-000 |
| Деталь: | COVER, REAR |
| Парткод: | FE8-3474-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FE8-3475-000 |
| Деталь: | RING, E |
| Парткод: | FE8-3636-000 |
| Деталь: | BUSHING |
| Парткод: | FE8-3643-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FE8-3644-000 |
| Деталь: | PANEL, OPEN/CLOSE |
| Парткод: | FL1-2517-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-N703-000 |
| Деталь: | ROLLER, PICK-UP |
| Парткод: | FC8-9251-000 |
| Цена: | 440 ₽ |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL3-1023-000 |
| Цена: | 600 ₽ |
| Деталь: | GEAR, 23T |
| Парткод: | FU2-1865-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1902-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1903-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE8-3462-000 |
| Деталь: | HINGE |
| Парткод: | FM1-T197-000 |
| Деталь: | COVER, HANDLE, LOWER |
| Парткод: | FE8-6739-000 |
| Деталь: | CAP |
| Парткод: | FE8-4189-000 |
| Деталь: | PAPER FEED GUIDE ASSEMBLY |
| Парткод: | FM1-P584-000 |
| Деталь: | DOCUMENT TRAY ASSEMBLY |
| Парткод: | FM1-N711 -000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | READER/ADF ASSEMBLY |
| Парткод: | NPN |
| Деталь: | SPACER, CIS |
| Парткод: | FE8-3479-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FE8-6736-000 |
| Деталь: | CONTACT IMAGE SENSOR,FA106H-01 |
| Парткод: | FK4-4050-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-5054-000 |
| Деталь: | PULLEY UNIT |
| Парткод: | FL1-1412-000 |
| Деталь: | DC MOTOR ASSEMBLY |
| Парткод: | FM1-T334-000 |
| Деталь: | CABLE, READER SIGNAL, 3 |
| Парткод: | FM2-C968-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | COPYBOARD GLASS UNIT |
| Парткод: | FM1-T335-000 |
| Деталь: | LABEL, WIDTH SIZE |
| Парткод: | FE8-6737-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FE8-9143-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FE8-4194-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | FM1-U532-000 |
| Деталь: | GUIDE ASSEMBLY, UPPER |
| Парткод: | FM1-N704-000 |
| Деталь: | ROLLER |
| Парткод: | FE8-3440-000 |
| Деталь: | FLAG,SENSOR |
| Парткод: | FE8-3444-000 |
| Деталь: | STOPPER, DOCUMENT |
| Парткод: | FE8-3645-000 |
| Деталь: | GUIDE, UPPER |
| Парткод: | FL1-2518-000 |
| Деталь: | SEPARATION PAD ASSEMBLY |
| Парткод: | FM1-P580-000 |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | FU2-1875-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-1904-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1905-000 |
| Деталь: | ROLLER, AUXILIARY |
| Парткод: | FU2-1906-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1922-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | PAPER FEEDER ASSEMBLY SET |
| Парткод: | FM1-U530-000 |
| Деталь: | GUIDE, PAPER DELIVERY |
| Парткод: | FE8-3446-000 |
| Деталь: | FLAG,SENSOR |
| Парткод: | FE8-3448-000 |
| Деталь: | BUSHING |
| Парткод: | FE8-3458-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE8-3459-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE8-3460-000 |
| Деталь: | RING, E |
| Парткод: | FE8-3636-000 |
| Деталь: | STOPPER, RATCHET SPRING |
| Парткод: | FE8-3655-000 |
| Деталь: | RATCHET, PAPER FEED ROLLER |
| Парткод: | FE8-3656-000 |
| Деталь: | LEVER, RELEASE |
| Парткод: | FE8-3657-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FL1-1367-000 |
| Деталь: | SHEET, GUIDE |
| Парткод: | FL1-1369-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FM1-N407-000 |
| Деталь: | MOTOR DRIVE ASSY |
| Парткод: | FM1-N709-000 |
| Деталь: | CABLE, SIGNAL, DF, 3 |
| Парткод: | FM2-C967-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-006 |
| Деталь: | CABLE, SENSOR |
| Парткод: | FM1-X903-000 |
| Деталь: | CABLE, GROUNDING |
| Парткод: | FM2-C969-000 |
| Деталь: | GEAR, 67T |
| Парткод: | FU2-1867-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU2-1869-000 |
| Деталь: | GEAR, 38T |
| Парткод: | FU2-1870-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1902-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1907-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1908-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | FK4-5055-000 |
| Деталь: | HOLDER, CONTACT IMAGE SENSOR |
| Парткод: | FE8-3450-000 |
| Деталь: | GLASS HOLDER UNIT |
| Парткод: | FL1-2502-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1924-000 |
| Деталь: | CONTACT IMAGE SENSOR SET |
| Парткод: | FM1-T027-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FL1-4365-000 |
| Деталь: | PAPER FEEDER ASSEMBLY |
| Парткод: | NPN |
Коды ошибок
E000-0000
E001-0000
E003-0000
E004-0000
E004-0005
E014-0000
E014-0001
E015-0001
E015-0002
E015-0003
E015-0004
E052-0000
E066-0000
E100-0000
E110-0000
E110-0001
E196-0000
E196-1000
E196-2000
E196-3000
E196-3001
E202-0001
E202-0002
E246-0000, E247-0000
E302-0001
E302-0002
E350-0000 ... E355-0005
E719-0000
E732-0001
E736-0000
E736-0001
E743-0000
E744-0001
E744-0002
E744-1001
E744-5000
E744-6000
E744-7000
E746-0000
E766-9000
E805-0001
E805-0002
E808-0000
Описание
| Error code: | E000-0000 |
| Description: | Startup error The temperature detected by the main or sub thermistor does not rise to the specified value during startup control. |
| Causes: | The detection temperature of the main thermistor did not increase after start of the power distribution to the heater. |
| Remedy: | - Check the fixing film connector. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0000 |
| Description: | Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature 235 deg C) during temperature control |
| Causes: | The main thermistor detected a temperature of higher than 255 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0000 |
| Description: | Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E004-0000 |
| Description: | Fixing power supply drive circuit error |
| Causes: | 43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly. |
| Error code: | E004-0005 |
| Description: | Fixing Relay fusion error |
| Causes: | At power ON or recovery from sleep mode, a zero cross signal was detected three times during the period of 100 ms after completion of CPU initialization. |
| Remedy: | 1. Check the harness/connector between the Fixing Assembly and the DC Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the DC Controller PCB. |
| Error code: | E014-0000 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor startup error The target speed was not reached within a specified time after startup of the motor. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E014-0001 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E015-0001 |
| Description: | Cassette 1 lift up motor error |
| Causes: | Cassette 1 lift up motor error |
| Remedy: | Reconnect the connector J151 on the DC controller PCB and the relay connector J742. Check the cassette media stack surface sensor in the sensor monitor mode. If a failure is found, replace the lifter drive unit. Replace the lifter drive unit. |
| Error code: | E015-0002 |
| Description: | Cassette 2 lift up motor error |
| Causes: | Cassette 2 lift up motor error |
| Remedy: | Reconnect the connector J2003 on the paper feeder driver PCB and the relay connector J702. Check the paper feeder media stack surface sensor in the sensor monitor mode. If a failure is found, replace the pickup unit. Reconnect the connector J2006 on the paper feeder driver PCB. Replace the lifter drive unit. |
| Error code: | E015-0003 |
| Description: | Cassette 3 lift-up error |
| Causes: | After lift-up of the Lifting Plate of the second casstte of the Paper Feeder started, ON status of the Paper Surface Sensor of the second casstte of the Paper Feeder was not detected within the specified period of time. |
| Remedy: | 1. Turn ON the power with the cassette of the Paper Feeder removed, insert the cassette, and then check the operation sound of the Lifter Motor. When there is operation sound of the Lifter Motor, check if the Lifting Plate has been lifted up. <When the Lifting Plate has been lifted up> 1. Check the harness/connector between the Paper Feeder Controller PCB and the Paper Surface Sensor of the Paper Feeder. 2. Replace the Paper Feeder Controller PCB. 3. Replace the DC Controller PCB. <When the Lifting Plate has not been lifted up> 1. Check the condition of the gear of the Paper Feeder (missing teeth, swing). 2. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter mater. 3. Replace the Drive Unit (included the Lifter Motor). <When there is no operation sound of the motor> 1. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter Motor of the Paper Feeder Unit. 2. Replace the Cassette Feeder Controller PCB. 3. Replace the DC Controller PCB. |
| Error code: | E015-0004 |
| Description: | Cassette 4 lift-up error |
| Causes: | After lift-up of the Lifting Plate of the third casstte of the Paper Feeder started, ON status of the Paper Surface Sensor of the third casstte of the Paper Feeder was not detected within the specified period of time. |
| Remedy: | 1. Turn ON the power with the cassette of the Paper Feeder removed, insert the cassette, and then check the operation sound of the Lifter Motor. When there is operation sound of the Lifter Motor, check if the Lifting Plate has been lifted up. <When the Lifting Plate has been lifted up> 1. Check the harness/connector between the Paper Feeder Controller PCB and the Paper Surface Sensor of the Paper Feeder. 2. Replace the Paper Feeder Controller PCB. 3. Replace the DC Controller PCB. <When the Lifting Plate has not been lifted up> 1. Check the condition of the gear of the Paper Feeder (missing teeth, swing). 2. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter mater. 3. Replace the Drive Unit (included the Lifter Motor). <When there is no operation sound of the motor> 1. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter Motor of the Paper Feeder Unit. 2. Replace the Cassette Feeder Controller PCB. 3. Replace the DC Controller PCB. |
| Error code: | E052-0000 |
| Description: | Erroneous connection to duplex unit Disconnection of the duplex unit was detected after power-on, detection of normal connection to the duplex unit, and start of communication. |
| Causes: | Failed to detect 2-sided unit Cause: improper 2-sided unit connection |
| Remedy: | - Check the connectors of the duplex unit and DC controller PCB. - Replace the duplex controller PCB. - Replace the DC controller PCB. |
| Error code: | E066-0000 |
| Description: | Environment sensor failure |
| Causes: | Environment sensor failure |
| Remedy: | Replace the environment sensor. |
| Error code: | E100-0000 |
| Description: | BD detection PCB failure The BD detection PCB is faulty. |
| Causes: | Yellow optical assembly failure |
| Remedy: | - Check the connector of the BD detection PCB. - Replace the laser scanner unit. - Replace the DC controller PCB. |
| Error code: | E110-0000 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor initial operation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0001 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor rotation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E196-0000 |
| Description: | Invalid RFU execution requested |
| Causes: | D-con update for the host machine or the optional cassette is not completed. |
| Error code: | E196-1000 |
| Description: | Main Controller PCB reading/writing error Error in reading/writing of main program in the Main Controller PCB |
| Causes: | Error in writing in / reading from ROM (main) Cause: Problem in main controller PCB |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E196-2000 |
| Description: | ROM read/write error (Error in storing each setting values for user mode / service mode / factory mode) |
| Causes: | Error in writing in/reading from ROM (storing settings) Cause: Problem in main controller PCB |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Update the set of the Controller Firmware (2) Replace the Main Controller Board. |
| Error code: | E196-3000 |
| Description: | ROM writing/reading error (eMMC) |
| Causes: | Unable to read/write data from the eMMC. The eMMC failure occurred. |
| Remedy: | 1. Update the firmware. 2. Replace the Main Controller PCB (UN30). |
| Error code: | E196-3001 |
| Description: | ROM-ID mismatch (eMMC) |
| Causes: | The eMMC was replaced incorrectly. The eMMC failure occurred. |
| Remedy: | 1. Update the firmware. 2. Replace the Main Controller PCB (UN30). |
| Error code: | E202-0001 |
| Description: | Reader HP sensor fault |
| Causes: | Reader HP outward fault The CCD unit moves backward, but does not move to the home position. |
| Remedy: | - Replace reader HP sensor. - Replace reader motor sensor. - Replace reader unit. |
| Error code: | E202-0002 |
| Description: | Contact Sensor HP error, Failure in return |
| Causes: | Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board. |
| Error code: | E246-0000, E247-0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E302-0001 |
| Description: | Shading error |
| Causes: | When the light intensity is below the reference level at shading |
| Remedy: | 1. Disconnect and then connect the Flexible Cable. 2. Replace the Flexible Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB (PCB2). |
| Error code: | E302-0002 |
| Description: | Shading error |
| Causes: | Image sampling for shading was not completed. |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Check the connection of the harness. 3. Replace the Main Controller PCB. 4. Replace the Reader Unit. |
| Error code: | E350-0000 ... E355-0005 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the sales company. |
| Error code: | E719-0000 |
| Description: | Erroneous communication with card reader (serial communication) - Disconnection from the card reader has been detected since communication started after confirmation of normal connection to the card reader (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.) |
| Causes: | Erroneous communication with card reader (serial communication) - Disconnection from the card reader has been detected since communication started after confirmation of normal connection to the card reader (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.) |
| Remedy: | - Check the connectors of the card reader and image processor PCB. - Replace the card reader for normal connection. - Replace the image processor PCB. |
| Error code: | E732-0001 |
| Description: | Scanner communication error |
| Causes: | Scanner communication error |
| Remedy: | 1. Update the firmware. 2. Replace the Main Controller PCB. |
| Error code: | E736-0000 |
| Description: | CCU communication error The installed modem PCB is incompatible. |
| Causes: | Error in CCU-modem communication Cause: Problem in FAX-NCU PCB / main controller PCB |
| Remedy: | - Check the connectors of the image processor PCB and modem. - Replace the modem PCB. - Replace the image processor PCB. |
| Error code: | E736-0001 |
| Description: | Error in ROM for backing up fax data |
| Causes: | An error occurred in ROM for backing up fax data. |
| Remedy: | 1. Check the connection of the NCU PCB (UN38). 2. Replace the NCU PCB (UN38). 3. Replace the Main Controller PCB (UN30). |
| Error code: | E743-0000 |
| Description: | Error in main controller communication An error in reading of/writing to the Flash ROM in the Main Controller occurred. |
| Causes: | Software sequence error |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. |
| Error code: | E744-0001 |
| Description: | Language file/boot ROM/USB memory error The language file version does not match Bootable. |
| Causes: | Language file version error The language file version does not match Bootable. |
| Remedy: | Download a language file of the correct version. |
| Error code: | E744-0002 |
| Description: | Language file/boot ROM/USB memory error The language file is longer than the permitted size. |
| Causes: | Language file size error The language file is longer than the permitted size. |
| Remedy: | Download a language file of the correct version. |
| Error code: | E744-1001 |
| Description: | Firmware version error Version of the main program and the version of the start-up program was not matched. |
| Causes: | Versions of Bootable and BootRom do not match |
| Remedy: | Install the set of the controller firmware. |
| Error code: | E744-5000 |
| Description: | Error in the Control Panel PCB Error in the Control Panel PCB (microcomputer). |
| Causes: | Error in panel microcomputer |
| Remedy: | 1. Check the Control Panel PCB, and install the firmware (PANEL). 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB. |
| Error code: | E744-6000 |
| Description: | Communication error with Wireless LAN board. |
| Causes: | Communication with the Wireless LAN PCB could not be established. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Wireless LAN Board. (4) Replace the Main Controller Board. |
| Error code: | E744-7000 |
| Description: | Main Controller PCB error An error in the microcomputer which retains fax job information of the Main Controller PCB. |
| Causes: | An error in the microcomputer which retains fax job information of the Main Controller PCB. |
| Remedy: | 1. Install the firmware of BKUP. 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB. |
| Error code: | E746-0000 |
| Description: | Main Controller PCB error Main Controller communication error occurred (other than scan). |
| Causes: | Communication error occurred in main controller PCB (other than scannerrelated) Cause: Problem in main controller PCB |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E766-9000 |
| Description: | Scanner power state error An error was detected in power state of the Laser Scanner Unit. |
| Causes: | Error in laser scanner unit power supply Cause: Problem in firmware |
| Error code: | E805-0001 |
| Description: | Error in duplex cooling fan |
| Causes: | Fan 1 failure |
| Error code: | E805-0002 |
| Description: | Fan Motor 2 error |
| Causes: | The Sub Fan fails to rotate at the specified rotation speed. |
| Remedy: | 1. Check the connection of the Sub Fan. 2. Replace the Sub Fan. |
| Error code: | E808-0000 |
| Description: | Fixing drive circuit failure - The heater does not turn on. - A fixing drive motor failure was detected. |
| Causes: | Printer detected failure in low-voltage power supply Cause: Failure in low-voltage power supply, problem in DC controller PCB |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the fixing drive motor. - Replace the DC controller PCB. - Replace the power supply PCB. |
