Canon imageCLASS MF8010Cn
Рейтинг
Модули
FIXING ASSY
INTERNAL COMPONENTS 3
INTERNAL COMPONENTS 1
LASER SCANNER ASSY
READER/ ADF ASSEMBLY (ADF MODEL)
PAPER FEEDER ASSEMBLY (ADF MODEL)
INTERMEDIATE TRANS. BELT ASSY
EXTERNAL COVERS, PANELS, ETC.
INTERNAL COMPONENTS 2
INTERNAL COMPONENTS 4
INTERNAL COMPONENTS 5
MAIN CONTROLLER PCB ASSEMBLY
CASSETTE
READER ASSEMBLY
READER/COPYBOARD ASSEMBLY (COPYBOARD MODEL)
Детали INTERNAL COMPONENTS 4
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM3-3434-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | RM1-4432-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | RM1-4433-000 |
| Цена: | 10 700 ₽ |
| Деталь: | ROLLER, PRESSURE |
| Парткод: | RC2-2146-000 |
| Цена: | 3 000 ₽ |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-3435-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | RM1-4430-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | RM1-4431-000 |
| Деталь: | GUIDE, CABLE, D |
| Парткод: | RC2-1822-000 |
| Деталь: | GUIDE, CABLE, F |
| Парткод: | RC2-1824-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-2111-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-2112-000 |
| Деталь: | BLOCK, LOCK, RIGHT |
| Парткод: | RC2-2142-000 |
| Деталь: | BLOCK, LOCK, LEFT |
| Парткод: | RC2-2143-000 |
| Деталь: | CAP, GUIDE |
| Парткод: | RC2-2144-000 |
| Деталь: | FLAG, DOOR SENSOR, REAR |
| Парткод: | RC2-2879-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RC2-2880-000 |
| Деталь: | COVER, DOOR SENSOR |
| Парткод: | RC2-2881-000 |
| Деталь: | SUPPORT, HIGH VOLTAGE PCB |
| Парткод: | RC2-2899-000 |
| Деталь: | LEVER, CARTRIDGE TRAY PUSH |
| Парткод: | RC2-2902-000 |
| Деталь: | HOLDER, CARTRIDGE TRAY PUSH |
| Парткод: | RC2-2904-000 |
| Деталь: | LEVER, CARTRIDGE TRAY PUSH |
| Парткод: | RC2-2906-000 |
| Деталь: | GUIDE, I.T.B., R |
| Парткод: | RC2-2907-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | RC2-3100-000 |
| Деталь: | HOLDER, CONTACT SPRING |
| Парткод: | RL1-1844-000 |
| Деталь: | HOLDER, CONTACT SPRING |
| Парткод: | RL1-1845-000 |
| Деталь: | HOLDER, CONTACT SPRING |
| Парткод: | RL1-1846-000 |
| Деталь: | SCREW, D, M3X12 |
| Парткод: | XA9-1830-000 |
| Деталь: | PAPER FEED GUIDE ASSY |
| Парткод: | RM1-4448-030 |
| Деталь: | I.T.B. LOCK LEVER ASSY, LEFT |
| Парткод: | RM1-4482-000 |
| Деталь: | I.T.B. LOCK LEVER ASSY, RIGHT |
| Парткод: | RM1-4483-000 |
| Деталь: | H.V. POWER SUPPLY PCB ASSY |
| Парткод: | RM1-4689-000 |
| Деталь: | ROLLER, TRANSFER |
| Парткод: | RM1-4445-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2017-000 |
| Деталь: | PAPER PICK-UP DRIVE ASSY |
| Парткод: | FM3-3454-000 |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1449-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, HOLDER |
| Парткод: | RC2-2014-000 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | RM1-4425-000 |
| Деталь: | PICK-UP ROLLER ASSY |
| Парткод: | RM1-4426-000 |
| Деталь: | COVER, SPRING, LEFT |
| Парткод: | FC7-9868-000 |
| Деталь: | COVER, SPRING, RIGHT |
| Парткод: | FC7-9869-000 |
| Деталь: | PRIORITY SLOT TRAY ASSY |
| Парткод: | FM3-3441-000 |
| Деталь: | RAIL, CASSETTE, RIGHT FRONT |
| Парткод: | RL1-1849-000 |
| Деталь: | HOLDER, MF TRAY, RIGHT |
| Парткод: | RC2-2006-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | RU6-2016-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2042-000 |
| Деталь: | RAIL, CASSETTE, LEFT FRONT |
| Парткод: | RC2-1878-000 |
| Деталь: | RAIL, CASSETTE, LEFT REAR |
| Парткод: | RC2-1879-020 |
| Деталь: | ARM, PRESSURE, LEFT |
| Парткод: | RC2-1882-000 |
| Деталь: | ARM, PRESSURE, RIGHT |
| Парткод: | RC2-1883-000 |
| Деталь: | ARM, MF TRAY, LEFT |
| Парткод: | RC2-1993-000 |
| Деталь: | ARM, MF TRAY, RIGHT |
| Парткод: | RC2-1997-000 |
| Деталь: | HOLDER, MF TRAY, LEFT |
| Парткод: | RC2-2007-000 |
| Деталь: | RAIL, CASSETTE, RIGHT REAR |
| Парткод: | RL1-1850-000 |
| Деталь: | PRIORITY SLOT DRIVE ASSY |
| Парткод: | RM1-4459-000 |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | FM3-3453-000 |
| Деталь: | ROLLER, PICK-UP |
| Парткод: | FC7-6189-000 |
| Цена: | 550 ₽ |
| Деталь: | BUSHING |
| Парткод: | FC7-6320-000 |
| Деталь: | FLAG, DOCUMENT SCANNER |
| Парткод: | FC7-6321-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC7-6322-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FC9-1503-000 |
| Деталь: | COVER, REAR |
| Парткод: | FC9-1532-000 |
| Деталь: | COVER, FRONT UPPER |
| Парткод: | FC9-1533-000 |
| Деталь: | TRAY, DOCUMENT |
| Парткод: | FC9-1534-000 |
| Деталь: | TRAY, SUB DOCUMENT |
| Парткод: | FC9-1535-000 |
| Деталь: | PANEL, OPEN/CLOSE |
| Парткод: | FC9-1536-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FC9-1539-000 |
| Деталь: | COVER, BASE |
| Парткод: | FC9-4502-000 |
| Деталь: | PLATE, PAPER SIZE |
| Парткод: | FC9-5115-000 |
| Деталь: | PLATE, PAPER SIZE |
| Парткод: | FC9-7575-000 |
| Деталь: | PLATE, PAPER SIZE |
| Парткод: | FC9-7576-000 |
| Деталь: | PLATE, PAPER SIZE |
| Парткод: | FC9-5109-000 |
| Деталь: | TRAY, SUB |
| Парткод: | FC9-5655-000 |
| Деталь: | GUIDE, DOCUMENT, FRONT |
| Парткод: | FC9-5656-000 |
| Деталь: | GUIDE, DOCUMENT, REAR |
| Парткод: | FC9-5657-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FC9-7561-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FC9-7562-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FC9-7564-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FC9-7563-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FC9-7565-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FC9-7566-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FC9-7568-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FC9-7567-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL2-6637-000 |
| Цена: | 650 ₽ |
| Деталь: | HINGE, ADF |
| Парткод: | FL3-2453-000 |
| Деталь: | HOLDER, DOCUMENT,RELEASE SHEET |
| Парткод: | FL3-3539-000 |
| Деталь: | PAPER FEED GUIDE ASSEMBLY |
| Парткод: | FM4-1883-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM3-9538-000 |
| Цена: | 3 700 ₽ |
| Деталь: | SCREW, M3X10 |
| Парткод: | XA9-0831-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU7-0672-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2018-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FU7-8405-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FU7-8406-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FU7-8407-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0895-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2007-000 |
| Деталь: | RETAINING RING |
| Парткод: | HC1-0586-000 |
| Деталь: | BUSHING |
| Парткод: | HU1-1022-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | RATCHET, PAPER FEED ROLLER |
| Парткод: | FC7-6052-010 |
| Деталь: | PAD, SEPARATION |
| Парткод: | FC7-6297-000 |
| Цена: | 230 ₽ |
| Деталь: | HOLDER, SEPARATION PAD |
| Парткод: | FC7-6299-000 |
| Деталь: | CLAMP, SEPARATION PAD |
| Парткод: | FC7-6300-000 |
| Деталь: | LEVER, RELEASE |
| Парткод: | FC9-1512-000 |
| Деталь: | PLATE, ROLLER GROUNDING |
| Парткод: | FC9-1523-000 |
| Деталь: | GUIDE, PAPER DELIVERY |
| Парткод: | FC9-1526-000 |
| Деталь: | SHEET, SEPARATION PAD |
| Парткод: | FC9-5654-000 |
| Деталь: | ARM, SEPARATION SWING |
| Парткод: | FL3-1431-000 |
| Деталь: | GUIDE LOWER ASSEMBLY |
| Парткод: | FL3-1437-000 |
| Деталь: | PAPER FEED ROLLER ASSEMBLY |
| Парткод: | FM4-1885-000 |
| Деталь: | PAPER DELIVERY ROLLER ASSY |
| Парткод: | FL3-2458-000 |
| Деталь: | DRIVE PLATE ASSEMBLY |
| Парткод: | FM4-1880-000 |
| Деталь: | MOTOR DRIVE ASSY |
| Парткод: | FM4-8857-000 |
| Деталь: | ROLLER, AUXILIARY |
| Парткод: | FU5-6992-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU6-2998-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU6-2999-000 |
| Деталь: | GEAR, 20T |
| Парткод: | FU7-0667-000 |
| Деталь: | GEAR, 54T |
| Парткод: | FU7-0668-000 |
| Деталь: | GEAR, 46T/23T |
| Парткод: | FU7-0669-000 |
| Деталь: | GEAR, 36T |
| Парткод: | FU7-0671-000 |
| Деталь: | GEAR, 21T/42T |
| Парткод: | FU7-0676-000 |
| Деталь: | GEAR, 51T/17T |
| Парткод: | FU7-0678-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2016-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2008-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2010-000 |
| Деталь: | RETAINING RING |
| Парткод: | HC1-0586-000 |
| Деталь: | BUSHING |
| Парткод: | HU1-1022-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-004 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | GUIDE ASSEMBLY, UPPER |
| Парткод: | FM4-1882-000 |
| Деталь: | PAPER FEEDER ASSEMBLY |
| Парткод: | FM4-8856-000 |
| Деталь: | INTERMEDIATE TRANS. BELT ASSY |
| Парткод: | RM1-7866-000 |
| Деталь: | EMBLEM |
| Парткод: | FC5-5256-000 |
| Деталь: | EMBLEM |
| Парткод: | RC2-0062-000 |
| Деталь: | COVER, LEFT |
| Парткод: | FC9-4440-000 |
| Деталь: | COVER, RIGHT |
| Парткод: | FC9-4441-000 |
| Деталь: | GUIDE, SIDE, RIGHT |
| Парткод: | FC9-4442-000 |
| Деталь: | GUIDE, HANDLE |
| Парткод: | FC9-4443-000 |
| Деталь: | COVER, RIGHT FRONT |
| Парткод: | FC9-4446-000 |
| Деталь: | COVER, UPPER REAR |
| Парткод: | FC9-4449-000 |
| Деталь: | COVER, LOWER REAR |
| Парткод: | FC9-4451-000 |
| Деталь: | GUIDE, REAR |
| Парткод: | FC9-4452-000 |
| Деталь: | COVER, PAPER PICK-UP SLOT |
| Парткод: | FC9-4454-000 |
| Деталь: | COVER, MODULAR |
| Парткод: | FC9-4584-000 |
| Деталь: | HINGE ASSEMBLY |
| Парткод: | FM4-1493-000 |
| Деталь: | LABEL, GROUNDING CAUTION |
| Парткод: | FU7-8091-000 |
| Деталь: | COVER, TOP |
| Парткод: | FM4-4262-000 |
| Деталь: | COVER UNIT, FRONT |
| Парткод: | FM4-4266-000 |
| Деталь: | LABEL, FEED JAM CLEARING |
| Парткод: | FU7-8088-000 |
| Деталь: | LABEL, FEED JAM CLEARING |
| Парткод: | FU7-8089-000 |
| Деталь: | LABEL, HIGH TMP. CAUTION |
| Парткод: | FU7-8090-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM4-8630-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM4-8632-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM4-8642-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM4-8643-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM4-8637-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM4-8640-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM4-8636-000 |
| Деталь: | P-CI PCB ASSEMBLY |
| Парткод: | FM4-8967-000 |
| Деталь: | OFFHOOK PCB ASSEMBLY |
| Парткод: | FM4-8968-000 |
| Деталь: | MODEM PCB ASSEMBLY |
| Парткод: | FM4-9252-000 |
| Деталь: | MODEM PCB ASSEMBLY |
| Парткод: | FM4-9254-000 |
| Деталь: | MODEM PCB ASSEMBLY |
| Парткод: | FM4-9253-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | FM4-3684-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | FM4-3679-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | FM4-3678-000 |
| Деталь: | CORD, POWER SUPPLY |
| Парткод: | FM4-3695-000 |
| Деталь: | CORD, POWER SUPPLY |
| Парткод: | FM4-3696-000 |
| Деталь: | GUIDE, CABLE, A |
| Парткод: | RC2-1819-000 |
| Деталь: | GUIDE, CABLE, B |
| Парткод: | RC2-1820-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | RC2-1821-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-1922-000 |
| Деталь: | GUIDE, CABLE, RIGHT |
| Парткод: | RC2-2887-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | RC2-3071-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | MOTOR, DC |
| Парткод: | RL1-1617-000 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | RM1-4443-000 |
| Деталь: | SUB DRIVE ASSY |
| Парткод: | RM1-4478-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0104-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FL3-5856-000 |
| Деталь: | CORD, POWER |
| Парткод: | FK2-4390-000 |
| Деталь: | CORD, POWER |
| Парткод: | FK2-9583-000 |
| Деталь: | CORD, POWER |
| Парткод: | FH2-7082-000 |
| Деталь: | CORD, POWER, 230V |
| Парткод: | FH2-7080-000 |
| Деталь: | CAM, FRONT COVER, LEFT |
| Парткод: | FC7-9827-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, DOOR SIDE, LEFT |
| Парткод: | FC9-4455-000 |
| Деталь: | COVER, DOOR SIDE, RIGHT |
| Парткод: | FC9-4456-000 |
| Деталь: | FIXING DRIVE ASSY |
| Парткод: | FM3-3455-000 |
| Деталь: | COVER, CARTRIDGE TRAY, LOWER |
| Парткод: | RC2-1784-000 |
| Деталь: | LEVER, RAIL, LEFT |
| Парткод: | RC2-1871-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1561-000 |
| Деталь: | LEVER, ESTRANGEMENT |
| Парткод: | RC2-1911-000 |
| Деталь: | STOPPER, LEVER |
| Парткод: | RC2-1914-000 |
| Деталь: | CLAW, FRONT DOOR, LEFT |
| Парткод: | RC2-2871-000 |
| Деталь: | CLAW, FRONT DOOR, RIGHT |
| Парткод: | RC2-2872-000 |
| Деталь: | FLAG, DOOR SENSOR, FRONT |
| Парткод: | RC2-2877-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | RC2-2878-000 |
| Деталь: | CLAMP, CARTRIDGE TRAY, LEFT |
| Парткод: | RC2-3108-000 |
| Деталь: | CLAMP, CARTRIDGE TRAY, RIGHT |
| Парткод: | RC2-3109-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-1872-000 |
| Деталь: | CARTRIDGE TRAY ASSY |
| Парткод: | RM1-4428-000 |
| Деталь: | PLATE, USB GROUNDING |
| Парткод: | FC9-4507-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-1886-000 |
| Деталь: | DC CONTROLLER PCB ASSY |
| Парткод: | FM4-3676-000 |
| Деталь: | USB PCB ASSEMBLY |
| Парткод: | FM4-3989-000 |
| Деталь: | SPEAKER ASSEMBLY |
| Парткод: | FK2-9878-000 |
| Деталь: | CABLE, FIXING OUTER |
| Парткод: | FM4-3690-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | FK2-8767-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | RK2-3125-000 |
| Деталь: | FIXING POWER SUPPLY ASSEMBLY |
| Парткод: | FM4-3683-000 |
| Деталь: | GUIDE, CABLE, E |
| Парткод: | RC2-1823-000 |
| Деталь: | COVER, FIXING POWER SUPPLY |
| Парткод: | RC2-1830-000 |
| Деталь: | PLATE, STATIC CHARGE |
| Парткод: | RC2-2889-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-1951-000 |
| Деталь: | WIRELESS LAN PCB ASSEMBLY |
| Парткод: | FM4-9831-000 |
| Деталь: | IC, T6TH5EFG-0002(0), STANDARD |
| Парткод: | FK2-7852-000 |
| Деталь: | IC, MB87S1801 |
| Парткод: | FK2-8321-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM4-9260-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM4-9259-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM4-9258-000 |
| Деталь: | CASSETTE |
| Парткод: | FM4-4263-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FC9-1650-000 |
| Деталь: | MOUNT, SUPPORTER |
| Парткод: | FC9-2101-000 |
| Деталь: | SPACER, CIS |
| Парткод: | FC9-7573-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-1884-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-1950-000 |
| Деталь: | READER COVER UNIT |
| Парткод: | FM4-4308-000 |
| Деталь: | READER COVER UNIT |
| Парткод: | FM0-0437-000 |
| Деталь: | DC MOTOR ASSEMBLY |
| Парткод: | FM4-4301-000 |
| Деталь: | CONTACT IMAGE SENSOR ASSY |
| Парткод: | FM4-9076-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | SCREW, TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | CORE |
| Парткод: | FK2-5242-000 |
| Деталь: | CABLE, READER |
| Парткод: | FM4-3653-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | FM4-8847-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | FM0-0436-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FC9-1539-000 |
| Деталь: | COVER, BASE |
| Парткод: | FC9-4502-000 |
| Деталь: | PLATE, PAPER SIZE |
| Парткод: | FC9-7576-000 |
| Деталь: | COPYBOARD COVER ASSEMBLY |
| Парткод: | FM4-8634-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FU7-8406-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
Коды ошибок
E000-0000
E001-0000
E001-0001
E003-0000
E003-0001
E004-0000
E012-0000
E012-0001
E014-0000
E014-0001
E015-0001
E020-0000
E021-1003
E021-2003
E024-0000
E024-0001
E024-0002
E024-0003
E052-0000
E066-0000
E070-0000
E078-0000
E100-0000
E100-0001
E100-0002
E100-0003
E110-0000
E194-0000
E196-0000
E196-1000
E196-2000
E198-0000
E202-0001
E202-0002
E351-0000
E733-0000
E736-0000
E744-0001
E744-0002
E744-1001
E744-4000
E744-5000
E746-0000
E766-8000
E766-9000
E766-xxxx
E804-0004
E805-0005
E806-0000
E808-0000
E840-0000
Описание
| Error code: | E000-0000 |
| Description: | Startup error The temperature detected by the main or sub thermistor does not rise to the specified value during startup control. |
| Causes: | The detection temperature of the main thermistor did not increase after start of the power distribution to the heater. |
| Remedy: | - Check the fixing film connector. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0000 |
| Description: | Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature 235 deg C) during temperature control |
| Causes: | The main thermistor detected a temperature of higher than 255 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0001 |
| Description: | Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control. |
| Causes: | The sub thermistor detected a temperature of higher than 290 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0000 |
| Description: | Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0001 |
| Description: | Abnormally low temperature (detected by sub thermistor) After the temperature detected by the sub thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The sub thermistor detected a temperature of lower than 80 degree C for more than 2 seconds when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E004-0000 |
| Description: | Fixing power supply drive circuit error |
| Causes: | 43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly. |
| Error code: | E012-0000 |
| Description: | Error in ITB motor activation. |
| Causes: | The cycle of ITB motor speed detection signal does not move in the specified cycle after ITB motor drive is started. Cause Failure in ITB motor, failure in DC controller PCB |
| Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
| Error code: | E012-0001 |
| Description: | Error in ITB motor activation. |
| Causes: | If the ITB motor speed detection signal comes off the specified cycle after it turned once to the specified cycle. Cause Failure in ITB motor, failure in DC controller PCB. |
| Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
| Error code: | E014-0000 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor startup error The target speed was not reached within a specified time after startup of the motor. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E014-0001 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E015-0001 |
| Description: | Cassette 1 lift up motor error |
| Causes: | Cassette 1 lift up motor error |
| Remedy: | Reconnect the connector J151 on the DC controller PCB and the relay connector J742. Check the cassette media stack surface sensor in the sensor monitor mode. If a failure is found, replace the lifter drive unit. Replace the lifter drive unit. |
| Error code: | E020-0000 |
| Description: | Density sensor failure warning |
| Error code: | E021-1003 |
| Description: | Error in developing motor |
| Causes: | Developing motor does not rotate. Cause Failure in developing motor, failure in DC controller PCB. |
| Remedy: | - Check the connectors of developing motor, DC controller PCB - Replace the developing motor - Replace the DC controller PCB |
| Error code: | E021-2003 |
| Description: | Error in developing motor |
| Causes: | The cycle of developing motor speed detection signal does not move in the specified cycle after developing motor drive is started. Cause Failure in developing motor, failure in DC controller PCB |
| Remedy: | - Check the connectors of developing motor, DC controller PCB - Replace the developing motor - Replace the DC controller PCB |
| Error code: | E024-0000 |
| Description: | Toner level sensor failure |
| Causes: | Failure output from the toner level sensor (Yellow). Cause Memory controller PCB assembly fault, DC controller PCB assembly fault, toner cartridge fault. |
| Remedy: | - Replace toner cartridge - Replace memory controller PCB - Replace DC controller PCB |
| Error code: | E024-0001 |
| Description: | Toner level sensor failure |
| Causes: | Failure output from the toner level sensor (Magenta). Cause Memory controller PCB assembly fault, DC controller PCB assembly fault, toner cartridge fault. |
| Remedy: | - Replace toner cartridge - Replace memory controller PCB - Replace DC controller PCB |
| Error code: | E024-0002 |
| Description: | Toner level sensor failure |
| Causes: | Failure output from the toner level sensor (Cyan). Cause Memory controller PCB assembly fault, DC controller PCB assembly fault, toner cartridge fault. |
| Remedy: | - Replace toner cartridge - Replace memory controller PCB - Replace DC controller PCB |
| Error code: | E024-0003 |
| Description: | Toner level sensor failure |
| Causes: | Failure output from the toner level sensor (Black). Cause Memory controller PCB assembly fault, DC controller PCB assembly fault, toner cartridge fault. |
| Remedy: | - Replace toner cartridge - Replace memory controller PCB - Replace DC controller PCB |
| Error code: | E052-0000 |
| Description: | Erroneous connection to duplex unit Disconnection of the duplex unit was detected after power-on, detection of normal connection to the duplex unit, and start of communication. |
| Causes: | Failed to detect 2-sided unit Cause: improper 2-sided unit connection |
| Remedy: | - Check the connectors of the duplex unit and DC controller PCB. - Replace the duplex controller PCB. - Replace the DC controller PCB. |
| Error code: | E066-0000 |
| Description: | Environment sensor failure |
| Causes: | Environment sensor failure |
| Remedy: | Replace the environment sensor. |
| Error code: | E070-0000 |
| Description: | Error in ITB / TOP sensor |
| Causes: | Error in ITB / TOP sensor Cause: Problem in ITB / TOP sensor / DC controller PCB |
| Remedy: | • Check connectors of ITB unit and DC controller PCB. • Replace ITB units • Replace DC controller PCBs |
| Error code: | E078-0000 |
| Description: | Error in primary transfer disengagement. |
| Causes: | Primary transfer disengagement mechanism did not work properly. Cause Disengagement mechanism error, ITB Tension Sensor error, Pickup Motorerror, DC Controller PCB error |
| Remedy: | - Check the disengagement mechanism. - Check the connectors of the ITB Tension - - Sensor, Pickup Motor and the DC Controller PCB (J167, J202, J160, J201, J140). - Replace the ITB Tension Sensor. - Replace the Pickup Motor. - Replace the DC Controller PCB. |
| Error code: | E100-0000 |
| Description: | BD detection PCB failure The BD detection PCB is faulty. |
| Causes: | Yellow optical assembly failure |
| Remedy: | - Check the connector of the BD detection PCB. - Replace the laser scanner unit. - Replace the DC controller PCB. |
| Error code: | E100-0001 |
| Description: | Error detection on any of scanner motor, laser unit, and BD detection at scanner area. |
| Causes: | Magenta optical assembly failure |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Laser Scanner Unit. (2) Replace the DC Controller Board. |
| Error code: | E100-0002 |
| Description: | Optical assembly error (Laser) |
| Causes: | Cyan optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E100-0003 |
| Description: | Optical assembly error (Laser) |
| Causes: | Black optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0000 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor initial operation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E194-0000 |
| Description: | Error in CPR sensor |
| Causes: | If CPR sensor is judged error. Cause Soiling in density detection sensor, failure in density detection sensor, failure in DC controller PCB, failure in toner cartridge. |
| Remedy: | - Check the connector of DC controller PCB - Replace the ITB unit - Replace the DC controller PCB - Replace the toner cartridge |
| Error code: | E196-0000 |
| Description: | Invalid RFU execution requested |
| Causes: | D-con update for the host machine or the optional cassette is not completed. |
| Error code: | E196-1000 |
| Description: | Main Controller PCB reading/writing error Error in reading/writing of main program in the Main Controller PCB |
| Causes: | Error in writing in / reading from ROM (main) Cause: Problem in main controller PCB |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E196-2000 |
| Description: | ROM read/write error (Error in storing each setting values for user mode / service mode / factory mode) |
| Causes: | Error in writing in/reading from ROM (storing settings) Cause: Problem in main controller PCB |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Update the set of the Controller Firmware (2) Replace the Main Controller Board. |
| Error code: | E198-0000 |
| Description: | DC controller memory failure |
| Causes: | A checksum failure is found in the block where specific information of the DC controller PCB is saved. A communication error occurred when reading the specific information of the DC controller PCB from the NVRAM at power-on. |
| Remedy: | If the failure cannot be removed by turning the power OFF/ON, replace the DC controller PCB. |
| Error code: | E202-0001 |
| Description: | Reader HP sensor fault |
| Causes: | Reader HP outward fault The CCD unit moves backward, but does not move to the home position. |
| Remedy: | - Replace reader HP sensor. - Replace reader motor sensor. - Replace reader unit. |
| Error code: | E202-0002 |
| Description: | Contact Sensor HP error, Failure in return |
| Causes: | Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board. |
| Error code: | E351-0000 |
| Description: | Main controller PCB fault |
| Causes: | Internal error of the main controller PCB Cause Main controller PCB fault. |
| Remedy: | - Check the connection of main controller PCB. - Replace main controller PCB. |
| Error code: | E733-0000 |
| Description: | Erroneous communication between controller and printer Cannot communicate with the printer at startup. |
| Causes: | Printer communication error (communication error at initial communication and negotiation packet error) |
| Remedy: | - Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB. |
| Error code: | E736-0000 |
| Description: | CCU communication error The installed modem PCB is incompatible. |
| Causes: | Error in CCU-modem communication Cause: Problem in FAX-NCU PCB / main controller PCB |
| Remedy: | - Check the connectors of the image processor PCB and modem. - Replace the modem PCB. - Replace the image processor PCB. |
| Error code: | E744-0001 |
| Description: | Language file/boot ROM/USB memory error The language file version does not match Bootable. |
| Causes: | Language file version error The language file version does not match Bootable. |
| Remedy: | Download a language file of the correct version. |
| Error code: | E744-0002 |
| Description: | Language file/boot ROM/USB memory error The language file is longer than the permitted size. |
| Causes: | Language file size error The language file is longer than the permitted size. |
| Remedy: | Download a language file of the correct version. |
| Error code: | E744-1001 |
| Description: | Firmware version error Version of the main program and the version of the start-up program was not matched. |
| Causes: | Versions of Bootable and BootRom do not match |
| Remedy: | Install the set of the controller firmware. |
| Error code: | E744-4000 |
| Description: | Engine ID error (Invalid engine connection is detected) |
| Causes: | Error in engine ID Detected illegal engine connection |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the DC Controller Board. (2) Update the Engine Firmware. (3) Update the set of the Controller Firmware |
| Error code: | E744-5000 |
| Description: | Error in the Control Panel PCB Error in the Control Panel PCB (microcomputer). |
| Causes: | Error in panel microcomputer |
| Remedy: | 1. Check the Control Panel PCB, and install the firmware (PANEL). 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB. |
| Error code: | E746-0000 |
| Description: | Main Controller PCB error Main Controller communication error occurred (other than scan). |
| Causes: | Communication error occurred in main controller PCB (other than scannerrelated) Cause: Problem in main controller PCB |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E766-8000 |
| Description: | Digital registration error Information at digital registration could not be obtained. |
| Causes: | Incorrect digital registration 3 point information Cause: Problem in firmware |
| Remedy: | 1. Install the Engine Controller firmware. 2. Install the set of the controller firmware. 3. Replace the Engine Controller PCB. |
| Error code: | E766-9000 |
| Description: | Scanner power state error An error was detected in power state of the Laser Scanner Unit. |
| Causes: | Error in laser scanner unit power supply Cause: Problem in firmware |
| Error code: | E766-xxxx |
| Description: | Firmware error An error due to the controller software occurred so that print could not be proceeded. |
| Causes: | Error in connection occurred due to main controller software *: xxxx Task number related to Exception is shown in decimal Cause: Problem in firmware |
| Remedy: | Due to firmware error, the possibility of solving the error by replacing the Main Controller PCB is low. Check the installed engine again. |
| Error code: | E804-0004 |
| Description: | Controller Fan error Since the startup of the Controller Fan, the Fan was locked for a specified consecutive period of time. |
| Causes: | Power supply cooling fan does not rotate in the specified rotation speed. Cause: Problem in power supply cooling fan / DC controller PCB |
| Remedy: | 1. Check power supply to the Controller Fan. 2. Replace the Controller Fan. |
| Error code: | E805-0005 |
| Description: | Error in duplex cooling fan |
| Causes: | Duplex cooling fan can not rotate the specified number of rotations. Cause Failure in duplex cooling fan, failure in DC controller PCB |
| Remedy: | - Check the connectors of duplex cooling fan and DC controller PCB - Replace the duplex cooling fan |
| Error code: | E806-0000 |
| Description: | Fan Motor cannot rotate at specified revolution speed. |
| Causes: | Fixing / fixing power supply cooling fan does not rotate in the specified rotation speed. Cause: Problem in fixing / fixing power supply cooling fan / DC controller PCB |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Main Fan Unit. (2) Replace the DC Controller Board. |
| Error code: | E808-0000 |
| Description: | Fixing drive circuit failure - The heater does not turn on. - A fixing drive motor failure was detected. |
| Causes: | Printer detected failure in low-voltage power supply Cause: Failure in low-voltage power supply, problem in DC controller PCB |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the fixing drive motor. - Replace the DC controller PCB. - Replace the power supply PCB. |
| Error code: | E840-0000 |
| Description: | Pressure release mechanism failure |
| Causes: | The target pressure position was not reached even when 3.5 seconds (approximately 1.5 rotation of the cam) elapsed after start of the fixing motor reverse rotation. |
| Remedy: | Check the gears and detection flags related to fixing pressure release mechanism. Replace the fixing pressure release sensor (PS9). Replace the fixing motor. Replace the fixing assembly. |
